TL8230A - MR Cavalieri SA

TL8230A - MR Cavalieri SA
TL8230A
User Guide
Programmable Thermostat
1.
4.
Description
Power-up
Honeywell’s TL8230A programmable thermostat can be connected to an
electric heater to control the room temperature.
On/Off switch *
Press the Day button to set the day.
Temperature display
5.
Error Messages
Mode display
Day and time
settings
LO: The measured temperature is below 32°F (0°C).
Heating is activated.
Preset temperature
icon
Heating power **
Period display
Program button
HI:
The measured temperature is above 122°F (50°C).
Temperature
preset buttons
Program
clear button
6.
Backlight
Temperature
adjustment
buttons
Mode selection /
program exit
Backlight button
**
) and displays the
Press the Hour and Min buttons to set the time.
Time and day display
Appears when
the setpoint is
displayed
*
Upon power-up, the thermostat is in manual mode (
actual temperature.
Set the switch to Off to cut power to the heater. This will not affect the time and temperature settings.
The thermostat displays the heater duty cycle required to maintain the desired temperature. For example,
appears when the heater is activated 40 percent of the
time.
When the backlight button is pressed, the display illuminates for 5 seconds.
When either of the
buttons is pressed, the display illuminates for 10 seconds.
7.
Temperature Setting
Setpoint
Display
% of duty cycle
1 to 24% 25 to 49% 50 to 74% 75 to 99%
The thermostat generally displays the actual temperature. To view the
setpoint, press one of the
buttons once or press the backlight button. The
setpoint will appear for the next 5 seconds.
100%
2.
Assembly/Disassembly
•
•
To change the setpoint, press one of the
buttons until the desired temperature is displayed. To scroll faster, hold the button.
Preset buttons
To remove the control module from the power
base, loosen the captive screw underneath the
thermostat and pull the two components apart
as shown.
The thermostat has 3 temperature preset buttons:
Comfort preset button
Economy preset button
Vacation preset button
To use a preset temperature, press the appropriate button. The corresponding
icon
,
or
will be displayed.
To install the control module onto the power
base, reverse the above procedure.
NOTE: Always keep the thermostat's vents clean and
unobstructed.
The following table shows the intended use and the default setting of each of
the preset buttons.
3.
Configuration
Icon
Intended use
Default setting
Some thermostat configurations can be
modified via the switches on the back of the
control module.
Comfort
70°F (21°C)
(when at home)
Economy
62°F (16.5°C)
(when asleep or away from home)
Default (factory) settings are inside the gray cells.
Vacation
(during prolonged absence)
b.
50°F (10°C)
#
Functionality
UP
DN
SW1
Temperature format a
°F
°C
SW2
Early Start b
Time format
Disable
Enable
Set the desired temperature using the
12-hour
24-hour
Press and hold the appropriate preset button until the corresponding
icon is displayed.
SW3
a.
New
If you change the temperature display format, the preset buttons ( , and
)
will return to their default settings.
Early Start functions in Automatic mode only. When this function is enabled, the
thermostat calculates the optimal time to start heating in order to obtain the desired
temperature by the set time. The thermostat re-assesses the start time daily based
on the previous day’s performance.
TL8230A
To store a preset temperature:
buttons.
Press Mode/Ret to exit.
69-1803
3/5/05
You created this PDF from an application that is not licensed to print to novaPDF printer (http://www.novapdf.com)
1/2
Use the following grid to record the new schedule.
8.
Operating Modes
Period
Setting
MO
TU
WE
TH
FR
SA
SU
The thermostat has 3 operating modes.
Automatic - The temperature is set according to the energy-saving
schedule. To place the thermostat in this mode, press Mode/Ret until
is
displayed. The current period setting is also displayed.
Temporary Bypass: If you modify the setpoint (by pressing the
,
or
button) when the thermostat is in automatic mode, the new setpoint
will be used until the beginning of the next period.
:
10.
Manual - The energy-saving schedule is not used. The temperature must
Technical Specifications
be set manually. To place the thermostat in this mode:
Press Mode/Ret until
is displayed.
Set the temperature using the
,
or
button.
Vacation - The thermostat is set to the Vacation temperature. Press
to place the thermostat in Vacation mode.
9.
Energy-saving Schedule
The schedule consists of 4 periods per day which represents a typical week
day. You can program the thermostat to skip the periods that do not apply to
your situation. For example, you can skip periods 2 and 3 for the weekend.
Period
Description
Associated temperature setting
Wake-up
Away from home
Return home
Sleep
The Comfort ( ) temperature is used in periods 1 and 3 and the Economy
( ) temperature is used in periods 2 and 4. For example, when the period
changes from 1 to 2, the setpoint automatically changes from Comfort setting
( ) to Economy setting ( ).
You can have a different program for each day of the week; i.e., each period
can start at different time for each day of the week. The thermostat has been
programmed with the following schedule.
Period
Setting
MO
TU
WE
TH
FR
SA
SU
6:00
am
6:00
am
6:00
am
6:00
am
6:00
am
6:00
am
6:00
am
8:00
am
8:00
am
8:00
am
8:00
am
8:00
am
--:--
--:--
6:00
pm
6:00
pm
6:00
pm
6:00
pm
6:00
pm
--:--
--:--
10:00
pm
10:00
pm
10:00
pm
10:00
pm
10:00
pm
10:00
pm
10:00
pm
To modify the schedule:
Press Pgm to access the programming mode. Period 1 is selected.
Press Day to select the day to program (hold for 3 seconds to select the
entire week).
Power supply: refer to the power base installation instructions
Display range: 32°F to 140°F (0°C to 60°C)
Setpoint range: 40°F to 86°F (5°C to 30°C)
Display resolution: 1°F (0.5°C)
Storage: -4°F to 120°F (-20°C to 50°C)
Heating cycle length: 15 minutes
Data backup: In the event of a power failure, most settings are saved. Only
the time must be re-adjusted if the power failure lasts more than 2 hours. The
thermostat will return to the mode that was active prior to the power failure.
11.
Warranty
Honeywell warrants this product, excluding battery, to be free from defects in the
workmanship or materials, under normal use and service, for a period of five (5)
years from the date of purchase by the consumer. If at any time during the warranty
period the product is determined to be defective or malfunctions, Honeywell shall
repair or replace it (at Honeywell's option).
If the product is defective,
(i)
return it, with a bill of sale or other dated proof of purchase, to the place from
which you purchased it, or
(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care will make
the determination whether the product should be returned to the following
address: Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr N,
Golden Valley, MN 55422, or whether a replacement product can be sent to
you.
This warranty does not cover removal or reinstallation costs. This warranty shall
not apply if it is shown by Honeywell that the defect or malfunction was caused by
damage which occurred while the product was in the possession of a consumer.
Honeywell's sole responsibility shall be to repair or replace the product within the
terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR
DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF
ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS
PRODUCT. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES
ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE FIVE-YEAR DURATION
OF THIS WARRANTY. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which
vary from state to state.
If you have any questions concerning this warranty, please write Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-4681502. In Canada, write Retail Products ON15-02H, Honeywell Limited/Honeywell
Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V4Z9.
Press Hour and Min to set the start time of the selected period, or press
Clear if you want to skip the period (--:-- is displayed).
Press Pgm to select another period, or press Day to select another day.
Then repeat step 3.
Press Mode/Ret to exit the programming mode.
NOTE: If no button is pressed for 60 seconds, the thermostat will automatically exit the programming mode.
TL8230A
12.
Customer Assistance
If you have any questions about the operation of your thermostat, please go to
www.honeywell.com/yourhome, or call Honeywell Customer Care toll-free
at 1-800-468-1502.
Printed in China
69-1803
3/5/05
You created this PDF from an application that is not licensed to print to novaPDF printer (http://www.novapdf.com)
2/2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement