- Computers & electronics
- Computer components
- System components
- Networking cards
- Tenda
- L8139D
- Data Sheet
advertisement
Table of Contents
1. P r o d u c t D e s c r i p t i o n … … … … 1
1.1 U n p a c k i n g … … … … … … … … 1
1.2 M a i n F e a t u r e s … … … … … … 1
1.3 S p e c i f i c a t i o n s … … … … … … … 2
1.4 N e t w o r k I n t e r f a c e a n d L E D
I n d i c a t o r s … … … … … … … … … … 2
2. H a r d w a r e I n s t a l l a t i o n … … … … 4
3. Software Installation……………4
1 Product Description
Thank you for purchasing TENDA
TEL9939D/TEL9939DI 10/100Mbps LAN adapter. TEL9939D/TEL9939DI is fully compliant with PCI2.2, supports ACPI
Power management, Auto-Negotiation.
And also supports data transfer rate of
10Mbps and 100Mbps, auto-detect the data transfer rate and duplex mode of the devices connected. Besides,
TEL9939D/TEL9939DI also supports
RPL/PXE. TEL9939D/TEL9939DI supports driver under the operating systems of
Windows 98, Windows ME, Windows 2000,
Windows NT, Windows XP, Windows NT,
Linux and Novell etc.
1.1 Unpacking
Please unpack the package and you could find:
TEL9939D or TEL9939DI LAN
Adapter
CD Driver
User’s Manual
1 pc
1 pc
1 copy
1 pc Quality-passed Certificate Card
1.2 Main Features z Compliant with IEEE802.3 Ethernet standard and IEEE802.3u fast
Ethernet standard z Supports data transfer rate of 10Mbps,
100MBps, 10Mbps/100Mbps under full/half duplex mode z Support NWAY Auto-Negotiation, auto detect data transfer rate, duplex
1
mode, and select optimal network connecting mode, avoid complex configuration, Plug-and-Play z Compliant with PCI 2.1, PCI 2.2 standard, support high efficient
32bit/33MHZ PCI, low CPU consumption. z Supports ACPI power management, extremely low consumption z MAX 200Mbps network throughput z Integrated First In First Out (FIFO) buffering area, enhance the data transfer capability of network z Adopting High Integration, High performance single chipset solution z Supports BootROM, insert the appointed BootROM and able to realize RPL/PXE (For TEL9939D only) z Supports abundant driving software, including almost all the common used operating system.
1.3 Specifications
Main Features
Standard
IEEE802.3
IEEE802.3u
BUS Type 32bit/33MHZ PCI BUS
Network
Interface
RJ45
I/O Address, System auto assigned
Disconnected
(IRO)
System auto assigned
Data Transfer
Rate
-10Mbps duplex half/full mode:
10/20Mbps
-100M half/full duplex mode:100/200Mbps
2
Operating
Temperature
Humidity
Consumption
0 ℃ ~45 ℃ (32 F
~112 F)
10%-90% condensing)
(non
Power input from the
PCI slot of the main-board, MAX 1.5 watts consumption
Compliances FCC Class B, CE
1.4 Network Interface and LED Indicators
TEL9939D/TEL9939DI supports one
RJ45 network Interface port, enables you to connect it to the network through Cat. 5 or Cat. 5 enhanced twisted pair cable.
TEL9939D/TEL9939DI supports one green Link/Act LED indicator. When there is no network connecting signal, the
Link/Act is OFF; When
TEL9939D/TEL9939DI is connected to the network successfully under the data transfer rate of 10Mbps or 100Mbps, the
LED Indicator is ON; When
TEL9939D/TEL9939DI is transferring or receiving data, the LED Indicator is blinking.
Location of the LED is as follows:
2 Hardware Installation
Please install the LAN Adapter according to the steps as follows:
1. Shut down your computer, unplug its power cord and remove the chassis cover.
2. Insert the contact edge of the
DGE-530T card into the connector of
3
any available PCI Bus Master expansion slot. Press the card firmly into the connector such that the card’ s contacts are fully seated in the connector.
3. Install the bracket screw that secures the card to the computer chassis and replace the computer’s chassis cover.
4. Connect TEL9901G to the network through Cat. 5 or Cat. 5 enhanced twisted pair cable.
3 Software Installation
Please install the driving software as follows:
1. Start PC, and insert the CD attached in the packing. The computer would run the CD automatically and display
TendaSetup on the screen. (If the computer is not running the CD automatically, please double click the CD and run
“TendaSetup.exe” ), please click the icon of “Driver” to install the driving software.
2. For TEL9939D, please click
“TEL9939D”, and for TEL9939DI please click “TEL9939DI”, then please select “the language of driver” and then click “Confirm” to start installation.
3. Please select the directory for
4. installation and click “ Next ”
Please click “ Finish” and you now install the driver successfully .
4
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project