K-3581T VAULT
SOAP DISPENSER HOLE
FAUCET HOLE
WHEN PLOTTING TEMPLATE FULL SIZE
Make sure horizontal and vertical dimensions
match the dimensions labeled on the template.
K-3581T
VAULT
OFFSET SELF-RIMMING AND UNDERCOUNTER KITCHEN
/
CUT-OUT TEMPLATE / INSTALLATION INSTRUCTIONS
·
WARNING: Risk of personal injury. Metal
surfaces are sharp and can cause severe cuts.
Use gloves and handle sink edges Carefully.
·
·
·
For new installations:
· Cut along the line dedicated to the installation type as
you desire.
· Carefully place the cutout template on the countertop
in the desired position.
· Make sure the sink will not interfere with the cabinet.
· Trace the cutout template outline onto the countertop.
· Drill a pilot hole inside the cutting line. Using a jig or
keyhole saw, cut along the outline to cut out the
opening in the Countertop.
·
·
RECOMMENDED TOOLS AND MATERIALS
·
·
·
·
·
·
·
·
For existing installations:
· Carefully lift the old sink out of the countertop.
· Compare the existing cut-out to the required cut-out
size.
· If needed, enlarge the cut-out hole according to the
directions for new installations.
·
·
·
·
·
·
·
·
Safety Glasses
Measuring Tape
Pencil
Drill
Putty Knife
Silicone Sealant
Pipe Wrench
Plumbers Putty
Plus:
· Level
· Cross Screwdriver
· Keyhole/Jigsaw
· Gloves
1.
1. Preparation
· Verify that there are no gaps.
· Allow the sealant to cure for at least 30 minutes.
·
·
· Apply silicone sealant.
· Immediately wipe away any excess sealant.
·
·
4. Connect Water Supply and Test
4.
· Install the garbage disposal, if used, according to the
manufacturer's instructions.
· Connect and tighten the trap to the strainer, and
complete the water supply connections to the faucet
according to the instructions packed with the faucet.
· Run water into the sink and check for leaks.
·
·
·
·
·
·
·
·
·
·
·
B. Undercounter Installation
· Install the strainer(s).
· Verify all required sink holes correspond with the
countertop cutout.
·
B.
·
·
Cutout template
35
·
·
28
Cutout template outline
·
·
·
·
Pilot Hole
Countertop
Trace the outline of the cutout template
on the countertop with a pencil at the
desired installation location.
ROUGHING-IN
K-3581T-1S
Unit: mm
Cut along the outline to cut out
the opening in the countertop
2. Install the Faucet Fitting and Drain
2.
· Install the faucet overflow pipe and strainer according
to the manufacturer's instructions.
·
800
400
200
· Measure the cabinet opening where the sink will be
installed. Plan for adequate clearance between the
faucet handles and the backsplash or finished wall.
· Construct a wood frame for the inside of the cabinet.
Allow adequate clearance for the faucet valving and
sink basin. Ensure the frame will support the entire
sink Rim.
·
·
Apply silicone sealant.
Stainless Steel
48.5
NOTE: If you are reusing fittings from an old sink, use
plumbers putty under the faucet base and top flange of
the strainer.
3. Install the Sink
Rinse your stainless steel sink thoroughly after each use,
and use a dabbing action to dry with a clean, soft cloth.
Clean stainless steel once a week.
3.
Clearance for the Sink Basin
Wood Frame
480
A. Self-rimming Installation
· Place the sink into the cut-out hole, and adjust it to a
proper position.
· Trace the outside outline of the sink onto the
countertop.
· Polish the inner side of the outside outline until the
inner side is about 2.5mm lower than the countertop.
· Install the clips into hole of the hook.
· Adjust the clip teeth parallel to the sink edge.
CARE AND CLEANING
A.
·
· Lower the sink into the cabinet. Verify the sink is
supported by the frame.
· Verify the sink is level, make any adjustments as
needed.
· Apply silicone sealant.
· Install the countertop.
·
·
2.5mm
·
·
·
·
·
·
/
Always apply stainless steel cleaner/polish with a
nonabrasive cloth or sponge, working with, not across the
grain. Do not use steel wool, wire brushes or abrasive
pads to clean your sink.
If you use cleaners containing chlorides, be sure to rinse
the surface immediately after you clean it to avoid
corrosion. Do not allow cleaners to remain in contact with
the sink surface for long periods of time.
Kohler kitchen sink accessories, including bottom basin
racks, wire rinse baskets, cutting boards and colanders
will help protect the surface of your sink.
K-3581T-2SD
400
70
46
If the surface becomes excessively dirty, consider using
baking soda, or a general purpose cleaner.
48.5
Clip Placement
747mm
786mm
RIM OF SINK
FOR SELF-RIMMING INSTALLATION
CUT ALONG THIS LINE
FOR UNDERCOUNTER INSTALLATION
CUT ALONG THIS LINE
1131858-T01-A
15
519180
, 2009
ã
ã Copyright Kohler China Ltd., 2009
466mm
·
WARNING: Risk of personal injury. Metal
surfaces are sharp and can cause severe cuts.
Use gloves and handle sink edges carefully.
Observe all local plumbing and building codes.
Shut off the hot and cold water supplies.
Prior to installation, unpack the new sink and inspect it
for damage. Return the sink to its protective carton
until you are ready to install it.
Inspect the drain and supply tubing. Replace if
necessary.
All information in these instructions is based on the
latest product information available at the time of
publication. Kohler china..reserves the right to make
changes at any time without notice.
·
370mm
·
·
·
· Apply a bead of quality sealant on the back rim of the
sink.
· Position the sink onto the cut-out area. Don't loose the
clips.
· Tighten the screws to lower the sink rim down onto the
countertop. Do not overtighten.
· Use a dry cloth to wipe away any excess sealant.
INSTALLATION THE NEW SINK
BEFORE YOU BEGIN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising