Washing Machine OWNER`S Manual
사양 확인 및 배포
2009.08.26
세)생산기술팀
CONTACT INFORMATION
Website : http://www.e-daewoo.com
Call : 1-877-393-7823(1-877-DWESVC3)
Washing Machine OWNER'S Manual
DWD-WD1353WC/SC/RC
Features
■ Economic wash system
With artificial intelligence, the washer uses minimum energy and water by selecting
optimal water level and washing time.
■ Low noise system
The washer minimizes the washing and spinning noises by sensing the
amount of laundry.
■ Child-Lock
The Child-Lock system is adopted to prevent children from pressing any
button to change the program during operation.
■ Automatic Liquid Detergent Inlet
The washer offers convenience by automatic supply system of detergent
CONTENTS
Page
IMPORTANT SAFETY GUIDE................................................................................................................................2
PARTS AND FEATURES.........................................................................................................................................3
INSTALLATION INSTRUCTIONS............................................................................................................................4
INSTALLATION OF ACCESSORIES......................................................................................................................8
TO USE AUTOMATIC DETERGENT DISPENSER...............................................................................................9
OPERATING YOUR WASHER..............................................................................................................................10
THE FUNCTION OF CONTROL PANEL..............................................................................................................12
WASHING PROGRAM..........................................................................................................................................14
WASHING PROCEDURE AND SELECTION......................................................................................................16
GUIDE FOR OTHER USEFUL PROGRAMS.......................................................................................................17
MAINTENANCE.....................................................................................................................................................21
HOW TO CLEAN THE FILTER..............................................................................................................................22
REMOVING STAINS..............................................................................................................................................23
TROUBLE SHOOTING..........................................................................................................................................24
SPECIFICATION....................................................................................................................................................25
A NOTE TO YOU
Thank you for buying a DAEWOO appliance.
DAEWOO washers are easy to use, save time, and help you manage your home better.
This manual contains valuable information about how to operate and maintain your washer property and safely.
Please read it carefully.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to
prevent property damage, personal injury, or loss of life
IMPORTANT SAFETY INSTRUCTIONS
WARNING! - To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions,
including the following :
1. Read all instructions before using the appliance.
2. Do not wash or dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning
solvents, other flammable or explosive substances as they give off vapors that could ignite or explode.
3. Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near
children.
4. Before the appliance is removed from service or discarded, remove the door.
5. Do not reach into the appliance if the drum is moving.
6. Do not install or store this appliance where it will be exposed to the weather.
7. Do not tamper with controls
8. Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the usermaintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.
9. Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances
give off vapors that could ignite or explode.
10. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more.
HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a washing
machine, turn on all hot water faucets and let the water flow from each for several minutes.
This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by
providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
WARNING! - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a
qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not
modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified
electrician
OPERATION INSTRUCTIONS
"WARNING - To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance." This statement is omitted when the operating instructions are preceded by the safety instructions and are
included in the same manual.
Understanding your responsibilities when using the washer.
1. Do not use chlorine bleach ancd ammonida or acid(such as vingar or rust remover) in the same wash. Hazardous fumes can form.
2. Unplug power supply cord before attemping to service your washer.
3. Do not wash fiberglass material. small particles can stick to fabrics washed in following loads and cause skin irritation.
4. Do not spray water on the control panel of the washer. It could cause fire or an electric shock.
5. In case of the dual valve model, If you connect only cold water inlet valve, while water temperature is selected as hot or warm, there
can be water leakage form unconnected water inlet valve.
2
PARTS AND FEATURES
The parts and features of your washer are illustrated on the page.
Become familiar with all parts and features before using your washer.
NOTE
The drawings in the book may vary from your washer model.
They are designed to show the different features of all models coverd by this book,
So your model may not include all the features.
INLET HOSE
(HOT, OPTION)
INLET HOSE
(COLD)
POWER PLUG
CONTROL PANEL
DOOR
DRAIN HOSE
PUMP COVER
ADJUSTABLE LEG
Accessories
Drain hose
Inlet hose
Wrench
Owner’s Manual
Cap holder (4EA)
Pedestal (OPTION)
∗ Design of
pedestals is
subject to
change without
manufacturers
notice.
3
UNIT LEVELER AS
INSTALLATION INSTRUCTIONS
Removing transit bolts
1. Before operating the washer,
remove the transit bolts(4ea)
along with the rubber.
• If the bolts are not removed, it
may cause heavy vibration,
noise and malfunction.
2. U
nscrew the 4 bolts with the
spanner supplied. Keep the 4
bolts and spanner for future use.
• Whenever the appliance is
transported, the
transit bolts must be refitted.
3. Close holes with supplied cap
holders.
Location of your washer
• Check location where the washer will be installed. Make sure you have everything necessary for correct installation.
• Do not place or store your washer below 0°C (32°F) to avoid any damage from freezing.
Drain Hose
• Do not place or store laundry products on top of washer at any times.
Washer
• Install the washer on the horizontal solid floor. If the washer is installed on an unsuitable floor,
it could make considerable noise, vibrate severely and cause a malfunction.
If the washer is not level, adjust leg up or down for horizontal installation.
• Ventilation openings must not be obstructed by carpeting when the
Laundry
washer is installed on a carpeted floor.
Tub
• Leave some space (right & left : 1 inch, rear : 4 inch).
• In case of built-in installation, the distance between top of the washer
Approx.
1 inch
and bottom of upper plate should be at least 3mm.
Level adjustment
① If the washer is installed on an unsuitable floor, it could make
considerable noise, vibrate and cause a malfunction.
② Adjust the level of washer using adjustable legs.
• Please check if there is any gap between the four adjustable legs and the floor.
• Turning adjustable legs by the enclosed spanner and adding UNIT LEVELER AS, adjust the level of washer and
swaying of washer.
• After the adjustment is finished, turn the fixing nuts up tightly so that the washer maintains the adjustment.
Fixing Nut
adjustable leg
③ Make it sure that the washer does not sway when you press down the four corners of the washer’s top plate.
NOTE
There should be no swaying of washer and all the
adjustable legs should stick to the floor closely.
4
Connecting water supply hose
(Connect to the
w ate r
valv e of the w ashe r)
(Connect to the faucet)
• Water supply pressure must be between 4.5 and 145 PSI
(30~1000 kPa).
• Do not crossthread when connecting inlet hose to the valve. If
the water supply pressure is more than 145 PSI, a pressure
reducing device should be installed.
• Two Sealing washers are supplied with the water inlet hoses to
prevent water leaks.
• Check for leakage of washing machine connections by turning
the tap completely on.
• Periodically check the condition of the hose and replace the
hose if necessary.
• Make sure that there is no kink in the hose and that it is not
crushed.
• Be sure that the two water input ports are connected to the
correct water faucets. The connector for hot water is colored red.
Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact your local service center.
Do not install your washing machine in a room where temperatures below freezing may occur.
Frozen hoses may burst under pressure. The reliability of the electronic control unit may be impaired at
temperatures below the freezing point
If the appliance is delivered in the winter months and temperatures are below freezing, store the washing machine
at room temperature for a few hours before putting it into operation.
Drain system
max. 40inch
min. 24inch
• Never forget to install drain hose before operating your
washer.
• Open the packing box, and there is a drain hose inside the drum.
• Connect the drain hose to the drain outlet at the back side of the washer.
• Top of laundry tub must be at least 24 inches high and no higher than 40 inches from bottom of washer.
• When installing the drain hose to tub(sink), secure it tightly with a string.
• Proper securing of the drain hose will protect the floor from damage due to water leakage.
• When the drain hose is too long, do not force it back into the washer. This will cause abnormal noise.
max. 40inch
min. 24inch
Electrical connection
• Do not use an extension cord or double adaper.
• If the supply cold is damaged, it must be replaced by a qualified person in order to avoid a hazard.
• If the machine will not be used for an extended time, unplug it and shut off the water supply.
• Connect the machine to a grounded outlet in occordance with current wiring regulations.
• The appliance must be positioned so that the plug is easily accesible.
5
max. 40inch
min. 24inch
Minimum clearances for closet
installation
Installation Clearances
• Washer dimensions
• Closet installations require a minimum clearance.
Sides - 1 in(2.5cm)
Rear - 1 in(10.2cm)
Top - 32 in(81.3cm)
.9"
40 cm)
4
(10
3"
(7.6cm)
48 in.2*
(310 cm2)
40.1
(102cm)
27
(68.6 "
cm)
24 in.2*
(155 cm2)
31.8
(80.9cm)
• The location must be large enough to fully open the
washer door.
• Most installations require a minimum clearance.
Sides - 1 in(2.5cm)
Rear - 4 in(10.2cm)
Top - 32 in(81.3cm)
3"
(7.6cm)
[Closet Ventilation]
32"
(81.3cm)
• Additional spacing should be considered for
installation and servicing.
• Companion appliance spacing should also be
considered.
1"
(2.5 cm)
27"
(68.6 cm)
[Front view]
6
1"
(2.5 cm)
Power outlet
• Must be within 60 in. (1.5 m) of either side of the
washer. Do not overload the outlet with more than
one appliance.
• Time-delay fuse or circuit breaker is
recommended.
NOTE: It is the personal responsibility and
obligation of the customer to have a proper
outlet installed by a qualified electrician.
1"
(2.5 cm)
31.8"
(80.9cm)
1"
(2.5 cm)
[Side view]
Level floor
• Allowable slope under entire washer is 1°.
• To minimize noise and vibration, the washer
MUST be installed on a solidly constructed
floor.
• Carpeting and soft tile surfaces are not
recommended.
• Never install the washer on a platform or weakly
supported structure
NOTE: A firm, solid floor is even more critical to a
front-loading washer than to a top-loader. If your floor is wood and/or frame
construction, you may need to reinforce it.
Front-loaders use substantially faster spin
speeds than top-loaders, causing greater
vibration. If the floor is not solid, your washe
will vibrate. You will hear and feel the
vibration throughout your house.
7
INSTALLATION OF ACCESSORIES
*Please be sure to read and follow the installation operation manual. (Pedestal Model : P-W151W)
CAUTION : When installing the said product, please be sure to let the expert with electrictiy & machine related
training and sufficient experiences install it.
People’s safety is the first priority.
There are many safety particulars in the guidebook and
product. Therefore, please be sure to read and abide by all
safety particulars.
6. In order for the washer or dryer to operate properly the
combination of adjustable cases on the bottom must be
balanced. If the adjustable legs are not balanced due to a
unstable platform, it is needed to balance them by
adjusting the horizontal adjustment legs. And, to fix the
position of these legs, tighten the bolts by using wrench
provided as much as possible. This would result in a
balanced operation.
Excessive load is dangerous.
In case of installing and carrying the adjustable cases of
the washer and dryer, more than two persons should
do it together. Please let children not play on the cases.
Installation methods
1. Please take out the height-high shelf and its installation
manual from the wrapped box.
2. Please untie 4 horizontal adjustment legs of the washer
and dryer.
3. Please turn and insert 4 horizontal adjustment legs in the
lower part of adjustable cases.
7. Take out the back cover and screw from the left part of the
height-high shelf drawer.
Assemble 10 svrews at the holes back of the shelf.
8. After transferring it into the desired installation spot, try to
operate the washer or dryer and check whether there are
any mechanial noises and vibration.
N.B : In order for the washer or dryer to be operate the
combination of adjustable cases on the plain bottom.
When they are not at a level with each adjustment
legs of adjustable cases, leave the horizontal
adjustment legs as it is, and fasten the lock nut
towards the cases solidly.
4. Please place the washer or dryer on the adjustable cases.
N.B : The washer and dryer are heavy so that more than
two persons have to raise them together.
N.B : P
lease pull out the plugs of the washer and dryer in
use, lock the faucet and divide the supply hose and
drainage hose. Then, please pull out water from all
hoses.
5. After pulling out and opening the drawers of adjustable
cases forwards, pull out the accessory bags for bolts from
the drawer sand insert the spring washer (b) and plain
washer (c) into the joint
BOLT (a) in order.
9. After transferring them in the desired installation location,
get the washer or dryer operated and check whether there
are any mechanical noises and vibration.
8
TO USE AUTOMATIC DETERGENT DISPENSER
About detergent
About bleach
Designed specially to use only
HE(High Efficiency) detergent
'For HE-Washer'
& 'Safe for all loads'
Your DAEWOO washer is designed to use only High Efficiency (HE)detergents.
HE detergents are formulated specifically for Automatic liquid detergent dispenser washers and contain suds
reducing components.
HE detergents make less suds, improve washing and rinsing performance, and help to keep the interior of your
DAEWOO washer clean.
If a regular detergent is used, it may cause oversudsing and unsatisfactory performance.
For the best washing and rinsing performance, low-sudsing HE detergents are strongly recommended.
And this is also designed to use only bleach for HE-Washer and 'safe for all loads'.
If a regular bleach is used, it may cause decolorazation.
Concentration Level
This dispenser can use any liquid HE (High Efficiency) detergent, regardless of its concentration level.
Many liquid HE (High Efficiency) detergents can be found in a concentrated form, meaning that it has more active
ingredients in each drop, taking up less space as it uses less fluid per wash.
•T
he concentration level can usually be found on the label or cap of the liquid HE (High Efficiency) detergent bottle.
• You can select the concentration of your detergent every time. Detergent concentration levels consist of 3
step(C1 : Regular, C2 : Concentrated X2, C3 : Concentrated X3). Softener/Bleach concentration levels consists
of 2 step(S1/B1 : Regular, S2/B2 : Concentrated X2). All default concentration are set for X2.
• If the concentration is not explicitly identified on the bottle, select “X2” as the concentration level when setting the
automatic detergent dispenser options.
Concentration Level Setting
Detergent levels can be changed as following instrucion.
And the default concentration of all detergent is set.
Step 1. Press
Delay Wash button and Power button during three seconds to select liquid HE(High Efficiency)
detergent.
+
Step 2. Set
the detergent concentration by pressing the following buttons.
Main-Liquid
(X2)
(X3)
(X1)
(X2)
(X1)
(X2)
(X2)
(X1)
(X2)
Softener
Bleach
to confirm detergent concentration.
Step 3. After
Power button
After confirming, the power off by itself.
9
(X2)
OPERATING YOUR WASHER
To obtain the best washing results, you must operate your washer properly.
This section gives you this important information.
Adding and refilling the main-liquid detergent/fabric softener/bleach
• If the power is on and the one of detergents is insufficient,
will light up and buzzer on 10 times.
Detergent Case Cover
• And display the warning indication for each compartment.
: Main-Liquid Detergent
: Bleach
: Softener
Main-Liquid Detergent
Bleach
Softener
Pouring detergent, main-liquid detergent, liquid bleach, and liquid fabric softener to the automatic
dispenser following these steps:
1. Open the dispenser entrance cap according to the open guide direction.
2. Pour the laundry products under maximum fill line.
3. Close the dispenser entrance cap according to the close guide direction.
•
•
•
•
•
Not using powder detergents, but only using liquid detergents.
Do not input other substances except for laundry detergent, bleach, and softener.
Pouring each laundry products in their respective dispenser compartments.
Do not exceed the maximum fill line.
Check the caps closed tight.
• Each compartment has a maximum capacity as below.
Main-Liquid Detergent : 70 Oz(2L)
Bleach : 42 Oz(1.2L)
Softener : 70 Oz(2L)
NOTE : If you want to use bleach, press 'Bleach' button. The bleach will be automatically dispensed at the proper time during the wash cycle.
10
Preparing clothes for washing
• Close zippers, snaps, and hooks to avoid snagging
other items.
Remove pin, buckles, and other hard objects to avoid
scratching the washer interior.
• Empty pockets and pull them inside out.
• Turn down cuffs and turn synthetic knits inside out to
avoid pilling.
• Tie strings and sashes to avoid tangling.
• Treat spots and stains.
(See “Removing stains” )
Sorting
• Separate heavily soiled items from lightly soiled ones, even if they would normally be washed together.
• Separate dark colors from light colors, colorfast items from non-colorfast item.
Soil (Heavy, Normal, Light) Separate clothes according to amount of soil.
Color (White, Lights, Darks) Separate white clothes from colored clothes.
Lint (Lint producers, Collectors) Wash lint producers and lint collectors separately.
Loading
• Drop items into washer loosely.
Items should move easily through wash water for
best cleaning and wrinkle-free results.
• Mix large and small items in each load.
Load evenly to maintain washer balance.
An unbalanced load can make the washer vibrate
during spin.
• Load washer properly and select correct load size
setting. Overloading and selecting a setting too
small for the wash load can :
- Cause poor cleaning
- Increase wrinkling
- Create excessive lint
- Wear out items faster (because of pilling)
• Reduce wash time when using a small load size
setting. Load with only a few small items needs less
wash time.
• Use a large load size setting to reduce wrinkling |with permanent press clothes and some synthetic
knits.These items should have more room to move in the water than heavy items. (towels, jeans)
11
THE FUNCTION OF CONTROL PANEL
Press this switch to turn the power “ON” or “OFF”.
Operation and temporary stop is repeated as it is pressed. When you want to change program in
operating; Press the “Start / Pause” button → Select the program that you want to change → Press
the “Start / Pause” button again.
You can select the course you want and each lamp is turned on when that course is selected.
You can select the wash/rinse course you want and each lamp is turned on when that course is
selected.
You can select the spin speed you want and each lamp is turned on when that spin speed is
selected.
You can select the soil level you want and each lamp is turned on when that level is selected.
As this button is pressed, the soil level is selected by ’Normal’ → ’Heavy’ → ’Light’
You can select the volume of beeper you want and each lamp is turned on when that volume of
bepper is selected.
As this button is pressed, the volume of beeper is selected by ’Low’ → ’High’ → ’Off’
12
If can be used to pre-engaged in for wash 1 hour to 12 hours.
use to memorize frequently used program
To make a Custom Program.
1. Select a cycle.(’18:88’or’CEP’will be shown by turns)
2. Select Wash/Rinse Temperature, Spin Speed, and Soil Level.
3. Select other desired Options.
4. Press Start/Pause Button.
Use this function when you want to protect any accident occurring from handling of washer by a
child.
During an operation of washer, press ’BEEPER’buttons simultaneously during 3 second.
If this mode will be set successfully, Child Lock Lamp will be burn out.In Child Lock mode, no
button functions except Power button. And if you want to release this mode, press
’BEEPER’buttons simultaneously again during 3 second.
→
→
Change
the desired
program
→
*The Child Lock will be cancelled when power is off.
Use this option to raise the temperature of water Instead of heater.
If using this option, heater does not operate.
This option features :
• For tough stained clothes, underwear, or baby clothes.
• Steam is available with Sanitary, Bulky/Large, Perm.Press,Cotton/Normal, and Baby Wear cycles.
• Upgraded washing performance with low energy and water consumption.
• Do not load delicates such as wool, silk, and easily discolored clothes.
Note :
• Steam wash is a highly concentrated and efficient.It may seem there is no water inside the drum,
but this is normal.
• Steam spray may not be seen clearly through the door; however, the washer is spraying steam
strongly inside.
• During the steam operation, a spraying sound will be heard.This is not a malfunction.
Do not reach into the washer while operating.Steam can cause severe burns.
Adds time to the wash for better stain removal.
This option provides an additional rinse.
Use this option to ensure the removal of detergent or bleach residue from garments.
Use this option to rinse and then spin.
Use this option to supply bleach during the wash cycle.
13
WASHING PROGRAM
Program
Fabric type
Proper Temp.
Default data
Maximum Load
Normal
Mixed loads, Work Clothes,
Jeans, Shirts.
Warm / Cold
Wash: main wash
Rinse: 2
Spin: Medium
soil level : normal
Refer to
rating label
Cotton
Cotton, Linen, Towels, Shirts,
Sheets
Warm / Cold
Wash: main wash
Rinse: 2
Spin: Extra High
soil level : normal
Refer to
rating label
Delicate
Delicated laundry easily
damaged. (silk, curtains)
Cold / Cold
Wash: main wash
Rinse: 1
Spin: Low
soil level : normal
Refer to
rating label
Heavy
Duty
Heavy soiled clothes (blue-jean,
climbing clothes, back pack,
sports wear)
Warm / Warm
Wash: main wash
wash Rinse: 2
Spin: Medium
soil level : Heavy
Refer to
rating label
Sanitary
Heavy soiled underwear, work
clothes, diapers, etc.
Extra hot/cold
(Hot/Warm)
Wash: main wash
Rinse: 2
Spin: Medium
soil level : normal
Refer to rating
label
Steam
Spray
Comforter, Shirts, Trousers
(except especially delicate fabrics)
* Do not use Steam Spray with items
such as wool, blankets leather
jackets, silk, wet clothes, lingerie,
foam products, or electric blankets.
Speed
Wash
Lightly soiled clothes and
frequently washing clothes and
small amount of clothes.
Wash.
Cold / Cold
Wash: main wash
Rinse: 1
Spin: Low
soil level : light
Less than 3 kg
baby care
Baby’s clothing or any fabric that
requires extra rinsing
Warm/Warm
Wash: main wash
Rinse: 4
Spin: Medium
soil level : Normal
Less than 2 kg
Warm/Warm
Wash: main wash
Rinse: 1
Spin: Low
soil level : Normal
Less than
7 pairs.
Gym Shoes Machine washable shoes used
inside the gym.
Drum
Cleaning
Use to clean the Tub
and Drum.
The appropriate cleaning time is
one time per a month.
-
Cold/Cold
14
Steam
Wash: soak
Rinse: 2
Spin: Low
1 ~ 5 dry
clothes
Without load.
Soak
Baby care
Delay
Wash
Steam
Extra
Wash
Extra
Rinse
Rinse
+Spin
Bleach
Custom
Program
O
O
O
O
O
O
O
O
O
O
O
Delicate
Steam Spray
O
Cotton
O
O
O
O
O
O
O
Normal
O
O
O
O
O
O
O
Heavy Duty
O
O
O
O
O
O
O
Gym shoes
O
O
O
O
O
O
Sanitary
O
O
O
O
O
O
O
Speed wash
O
O
O
O
O
O
O
O
O
Drum Cleaning
15
WASHING PROCEDURE AND SELECTION
1. PROGRAM
1
Put the laundry into the Drum and check the detergent and softener in the detergent
case. If each detergent is not enough, pour the detergent into the detergent case.
Then close the Door.
Note : the method of using detergent refers title ‘OPERATING YOUR WASHER’ in this
manual.
2
Press the Power button.
• The LED shows only ‘- --’ signal.
Note : If the one of detergent is not enough, not only display the warning indication and hear warning sound, but the washer can be operating.
3
Select the program using the program selection dial.
• If you press ‘Start/Pause’ button after pressing Power button without selecting
program, the ‘Normal’ program is selected as default program.
• If you want to change the ‘Wash/Rinse’ and ‘Water Temperature’ and ‘Spin Speed’ and ‘Soil Level’ and ‘Beeper’, select program what you want to change by pressing
each button.
• If you want to use bleach, press ‘Bleach’ button. The bleach will be automatically
dispensed at the proper time during the wash cycle.
4
Press the ‘Start/Pause’ button.
• The washer will be operated with locking Door and supplying water after sensing the
amount of laundry automatically.
Note
• If you want to change the setting program during operation, press the ‘Start/Pause’ button to hold the
operation and change the program you want to change by pressing each corresponding button.
16
GUIDE FOR OTHER USEFUL PROGRAMS
1. Steam
1
Put 5 items or less into the Drum.
Then close the Door.
Note : Wipe the water off the drum.
Press the Power button.
2
• The LED shows only ‘- --’ signal.
Note : If the one of detergent is not enough, not only display the warning indication and hear warning sound, but the washer can be operating.
3
Select ‘Steam’ program using the program selection dial.
4
Press ‘Start/Pause’ Button.
Press ‘Start/Pause’ Button
• The ‘Steam’ program is not like other washing or drying cycles.
• Due to the characteristics of cotton fibers, this program is not recommended for 100% cotton clothing.
• Remove stains from clothing before using the ‘Steam’ program to prevent permanently setting the stains by
high heat.
• Be sure the faucet is open. This program uses a little water to produce steam.
• Be careful not to touch the door. It can be very hot.
• Do not load the following items: - Wool, blankets, leather jackets, silk, wet clothes, lingerie, foam products, or electric blankets.
• After removing clothes from the ‘Steam’ program they may feel slightly damp. Wait at least 10 minutes before
putting the clothes on.
• Best results are achieved when articles are of similar size and fabric type. Do not overload.
• Do not reach into the washer while operating. Steam can cause severe burns.
• Keep pets away from the washer.
17
2. Delay Wash
1
2
Put the laundry into the Drum and check the detergent and softener in the detergent
case.
If each detergent is not enough, pour the detergent into the detergent case.
Then close the Door.
Note : the method of using detergent refers title ‘OPERATING YOUR WASHER’ in this
manual.
Press the Power button.
• The LED shows only ‘- --’ signal.
Note : If the one of detergent is not enough, not only display the warning indication and hear warning sound, but the washer can be operating.
3
Select the program using the program selection dial.
• If you press ‘Start/Pause’ button after pressing Power button without selecting
program, the ‘Normal’ program is selected as default program.
• If you want to change the ‘Water Temperature’ and ‘Soil leve’ and ‘Washing Course’
and ‘Rinse Time(s)’ and ‘Spin Speed’, select program what you want to change by
pressing each button.
• If you want to use bleach, press ‘Bleach’ button.The bleach will be automatically
dispensed at the proper time during the wash cycle.
4
Press the ‘Delay Wash’ button.
• The ‘Delay Wash’ LED is to be lighting.
• Select the delay you want from 1 hour to 12 hours by pressing button.
• The displayed time shows program finishing time.
Press the ‘Start/Pause’ button.
• If you make this program successfully,only ‘Delay Wash’ and ‘Lock’ LED are lighting.
Note :
• If you want to check the selected program,press the ‘Start/Pause‘ button again.
•P
reparing washing before starting ‘Delay Wash’.
- Turn on the water tap.
- Load laundry and close Door.
- Place the detergent and fabric softener in the detergent case.
•T
he actual time of finishing is a little different with your selecting time because of water supply condition and selected water
temperature.
• ‘Gym Shoes’ and ‘Delicate’ and ‘Drum Cleaning’ and ‘Steam Spray’ program are not select ‘Delay Wash’.
• Adding clothes during ‘Delay Wash’ operation is not allowed.
18
3. CUSTOM PROGRAM
1
Put the laundry into the Drum and check the detergent and softener in the detergent
case.
If each detergent is not enough, pour the detergent into the detergent case.
Then close the Door.
Note : the method of using detergent refers title ‘OPERATING YOUR WASHER’ in this
manual.
2
Press the Power button.
• The LED shows only ‘- --’ signal.
Note : If the one of detergent is not enough, not only display the warning indication and hear warning sound, but the washer can be operating.
3
Press the Custom button.
• ‘18:88’ or ‘CEP’ will be shown by turns.
4
Press Start/pause Button.
• The washer will be operated with locking Door.
Note :
Use to memorize frequently used program
To make a Custom Program.
1. Select a cycle. (‘18:88’ or ‘CEP’ will be shown by turns)
2. Select Wash/Rinse Temperature, Spin Speed, and Soil Level.
3. Select other desired Options.
4. Press Start/Pause Button.
4. BLEACH
1
2
Put the laundry into the Drum and close the Door.
Press the Power button.
• The LED shows only ‘- --’ signal.
Note : If the one of detergent is not enough, not only display the warning indication and hear warning sound, but the washer can be operating.
3
Select the program using the program selection dial except for ‘Steam Spray’ program.
4
Press ‘Bleach’ button.
• The bleach will be automatically dispensed at the proper time during the wash cycle.
5
Press Start/pause Button.
• The washer will be operated with locking Door.
19
5. ONLY SPIN
1
2
Put the laundry into the Drum and close the Door.
Press the Power button.
• The LED shows only ‘- --’ signal.
Note : If the one of detergent is not enough, not only display the warning indication and hear warning sound, but the washer can be operating.
3
Select the ‘SPIN CONDITION’ you want by pressing ‘SPIN’ button.
• The ‘Normal’ program is selected automatically.
• The water temperature is selected to ‘Cold/Cold’ automatically.
4
Press the ‘Start/Pause’ button.
• The washer will be operated with locking Door.
6. RINSE+SPIN
1
Put the laundry into the Drum and check the detergent and softener in the detergent
case.
If each detergent is not enough,pour the detergent into the detergent case.
Then close the Door.
Note : the method of using detergent refers title ‘OPERATING YOUR WASHER’ in this
manual.
2
Press the Power button.
• The LED shows only ‘- --’ signal.
Note : If the one of detergent is not enough, not only display the warning indication and hear warning sound, but the washer can be operating.
3
Select the program you want using the program selection dial.
• If you press ‘RINSE+SPIN’ button without selecting program, the ‘Normal’ program is
selected as default program.
4
Press the ‘RINSE+SPIN’ button.
• ‘1’ time rinse and ‘Medium’ rpm spin speed and ‘Cold/Cold’ water temperature are
selected automatically.
• ‘Low’ rpm spin speed is selected in ‘DELICATE’ program.
• If you want to change the Rinse time(s)and Spin condition, press each corresponding
button.
5
Press the ‘Start/Pause’ button.
• The washer will be operated with locking Door.
Note : The water temperature selecting is possible during this process.
20
MAINTENANCE
Proper care of your washer can extend its life. This section explains how to care for your washer properly and
safely.
Cleaning your washer
Exterior
Interior
Wipe up detergent, bleach, and other spills with
a soft, damp cloth or sponge as they occur.
Occasionally wipe the outside of the washer to
keep its looking like new one.
Clean interior with 250ml of chlorine bleach
mixed with 500ml of detergent.
Run washer through a complete cycle.
Repeat this process if necessary.
Do not put sharp or metal object in your washer, or they can damage
the finish.
Check all pockets for pins, clips, money, bolts, nuts, etc.
Do not lay these objects in your washer after emptying pockets.
Winter storage or moving care
IInstall and store your washer where it will not freeze. Because some water may stay in the hoses, freezing can
damage your washer.
If you store or move your washer during freezing weather, winterize it.
To winterize washer
To use washer again
• Turn off water faucet.
• Flush water pipes and hoses.
• Disconnect and drain water inlet hoses.
• Reconnect water inlet hoses.
• Run washer on a drain and spin setting for 1 minute.
• Turn on water faucet.
• Unplug the power supply cord.
• Reconnect power supply cord.
Non-use or vacation care
Operate your washer only when you are at home.
If you are on vacation or don‘t use your washer for an extended period of time, you should:
• Unplug the power supply cord or turn off eletrical power to the washer.
• Turn off the water supplier to the washer.
This helps avoid accidental flooding (due to a water pressure surge) while you are away.
21
HOW TO CLEAN THE FILTER
Cleaning the water inlet filter
Clean the filter when water leaks from the water inlet.
① Pull the power plug out
before cleaning it.
② Turn off the water
supply to the washer
and separate the inlet
hose.
③ Pull the inlet filter out.
④ Remove the dirt from
the inlet filter with a
brush.
Cleaning the drain filter
• This drain filter is used to screen the foreign stuffs such as threads, coins, pins, buttons etc.
• If the drain filter is not cleaned at proper time(every 10 times of use), drain problem could be caused.
CAUTION : Be careful when draining if the water is hot.
① Open the lower cover(1) by using ② Unplug the cap hose(2), allowing ③ Remove any foreign material
a coin. Remove the cap hose(2)
the water to flow out. At this time
from the pump filter(3).
to pull out the hose.
use a vessel to prevent water
After cleaning, turn the pump
filter clockwise and insert the cap
flowing on to the floor.
hose(2) to the original place.
When water does not flow any
Close the lower cover.
more, turn the pump filter(3) open
to the left.
Cleaning the automatic detergent tanks
• If you want to clean the automatic detergent tanks, give DAEWOO Service center call.In that case, a service
man will teach the method of cleaning the automatic detergent tanks or clean the automatic detergent tanks.
• If you connect with the internet site, you can get the information of cleaning the automatic detergent tanks.
22
REMOVING STAINS
Stained, heavily-soiled, or greasy items may need to be prewashed or soaked for best results.
Soaking helps remove protein-type stains like blood, milk or grass.
Stain removal rules
• Use warm water for soaking or prewashing stained laundry. Hot water can set stains.
• Most stains are easier to remove when they are fresh.
• Before treating any stain, find out what kind of stain it is, how old the stain is, what kind of fabric it is, and whether the fabric is
colorfast. (Check the care label)
• Washing and drying can set some stains.
• Start with cold or warm water. Hot water can set some stains.
• When bleach is recommended, use a bleach that is safe for the fabric.
• Put the stained area face down on a paper towel or white cloth. Apply the stain remover to the back of the stain.
This forces the stain off fabric instead of through it.
Stain removal guide
STAIN
TO REMOVE
Blood
Rinse immediately in COLD water.
If stain remains, soak in cold water with an enzyme prewash.
Chewing gum
Use ice in plastic bag to harden the gum.
Scrape off what you can and the sponge with white spirits.
Cocoa, Chocolate
Sponge with COLD water and soak in an enzyme prewash.
If stains persist, rub in a little detergent and rinse in cold water.
Coffee
Blot up quickly and rinse out in COLD water.
Rub in a little detergent and wash in the maximum temperature allowed for the fabric type.
Cream/Milk/Ice cream
Rinse in COLD water and wash normally. If stain is still apparent, sponge with white spirits.
Deodorant
Rub affected area with white vinegar and then rinse out in COLD water. Sponge with white spirits.
Treat stiffened areas with enzyme prewash.
Egg
Soak in a COLD enzyme prewash, rinse and wash normally.
Fabric/Softener
Rub affected area with bar soap and wash normally.
Fruit stains
Treat as soon as possible by sponging with COLD water.
Rub a little detergent on the stain and wash normally.
Grass
Sponge with white spirits. Rub in an enzyme prewash and wash as normally.
Grease and oil
Lay the affected area face down on an absorbent cloth and work from the back.
Sponge with white spirits or dry cleaning fluid. Wash normally.
Iron or rust
Apply lemon juice and salt and place in the sun. Wash normally.
Lipstick
Sponge with white methylated spirits and wash normally.
Mildew
Wash in WARM water and detergent.
Moisten area with lemon juice, dry in the sun and wash normally.
If stain persists and the fabric allows, use a bleach.
Mud
Brush off any dry mud. Rinse in cold water.
If stain persists rub in a little detergent and wash normally.
Paint-oil based
Scrape off any fresh paint and sponge with a non flammable dry cleaning fluid
and wash normally.
Paint-water based
Treat while still wet, rinse in WARM water and wash normally.
Scorch marks
Dampen a cloth with hydrogen peroxide, lay it over the affected area and press
with a fairly hot iron.
23
TROUBLE SHOOTING
Most problems are easily solved if you understand the cause.
Check the following list for problem before calling for service.
If the error mode such as IE, OE, UE were displayed on the control part,in order to solve these problem, first turn
off the power of the washing machine and then turn on the power pressing Power button.
If PFE error mode was displayed on the control part,in order to solve this problem, first turn off the power of the
washing machine,second turn on the power pressing Power button, third press SPIN button and last press
Start/Hold button.
PROBLEM
CHECK POINT
• The washer will not operate at
all.
• Is there a power failure?
• Is the power cord correctly connected to an electric outlet?
• Did you turn on the power?
• Did you press Start/Hold button?
• Is there correct amount of laundry in the washer?
” will light up in this case.)
• Is the door open? (The lamp “
• Water is not supplied
Error display
• Did you connect the inlet hose and open the water tap?
• Is the inlet hose or the water tap frozen?
• Is the water supply shot off?
• Is there any foreign matter blocking up the inlet hose filter?
• The washer will not drain
Error display
• Is the drain hose frozen or blocked up by dirt?
• Is the drain hose kinked or deformed?
• Is the end of the drain hose immersed in water?
• Is there excessive dirt inside the drain filter?
• The washer will not spin
Error display
• Is the clothes in the drum collected on one side?
• Is the washer installed on an uneven floor or is the vibration serious?
• The washer will stop during
spinning .
•S
pinning is insufficient.
Error display
• Is the filter of the drain pump clogged?
• Is the drain pump operated?
• Did you use the proper amount of detergent?
• Is the drain hose placed higher than 1m above floor?
• Display the warning indication,
,
,
• Is Main-detergent enough?
• LEP : Main-Liquid Detergent, BEP : Bleach, SEP : Softener
• Vibrating and too noisy,
• Is the washer installed on an uneven floor?
• Have all the transit bolts removed?
Note
•If
and
error mode are showed on LED panel, please contact service center.
These cases are not malfunctions;
• The sound “wing” heard during water supply is the operating sound made by the water inlet valve.
24
SPECIFICATION
MODEL
DWD-WD1353WC/SC/RC
Dimension (inches)
27 x 31.8 x 40.1 (W x D x H) (Door open D : 40.9)
Unit Weight (lbm)
198.4(Net) / 227(Gross)
Wash capacity
3.92 cu.ft. DOE, 4.5 cu.ft. IEC, 10.4kg
Spin Speed (RPM)
1300 rpm max.
Operating Water Pressure
4.5~145 PSI (30~1000 kPa)
Electrical Spec.
120V / 60Hz, 10 A
WIRING DIAGRAM
25
DAEWOO washer LIMITED WARRANTY
Your DAEWOO will be will repaired or replaced, at DAEWOO’s option, if it proves to be defective in material or
workmanship under normal use, during the warranty period ("Warranty Period") set forth below, effective from the date
("Date of Purchase") of original consumer purchase of the product. This limited warranty is good only to the original
purchaser of the product and effective only when used in the United States, including Hawaii, and U.S. Territories.
WARRANTY PERIOD :
LABOR : ONE YEAR from the Date of Purchase.
PART : ONE YEAR from the Date of Purchase.
Replacement Units and Repair Parts may be new or factory remanufactured.
Replacement Units and Repair Parts are warrantyed for the remaining portion of the original unit’s warranty period.
HOW SERVICE IS HANDLED :
IN-HOME Service: Please retain dealer’s dated bill of sale or delivery ticket as evidence of the Date of Purchase for
proof of warranty, and submit a copy of the bill of sale to the service person at the time warranty service is provided.
Please call 1-877-393-7823(1-877-DWESVC3) and choose the appropriate option to locate your nearest
DAEWOO Autorized Service Center or visit website at : http://www.e-daewoo.com
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARRICULAR PURPOSE.
TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE
EXPRESS WARRANTY PERIOD ABOVE.
NEITHER THE MANUFACTURER NOR ITS U.S DISTRIBUTOR SHALL BE LIABLE FOR ANY INCIDENTAL
CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE. INCLUDING WITHOUT
LIMITATION, LOST REVENUES OR PRO PROFITS, OR ANY OTHER DAMAGE WHETHER BASED IN
CONTRACT, TORT, OR OTHERWISE.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how an
implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal
rights and you may also have other rights that vary from state to state.
THIS LIMITED WARRANTY DOES NOT APPLY TO :
Service trips to your home to deliver, pick up, and/or install the product, instruct, or replace hose fuses or correct wiring,
or correction of unauthorized repairs.
Damages or operating problem that result from misuse, abuse, operation outside environmental specifications or
contrary to the requirements of precautions in the Operating Guide, accident, vermin, fire, flood, improper installation,
acts of God, unauthorized modification or alteration, incorrect electrical current or voltage, or commercial use, or use for
other than intended purpose.
The cost of repair or replacement under these excluded circumstances shall be borne by the consumer.
CUSTOMER INTERACTIVE CENTER NUMBER
To obtain Customer Assistance, Product Information, or Dealer or Authorized Service Center location:
Call 1-877-393-7823(1-877-DWESVC3) and select the appropriate option from the menu. Or visit our website : http://
www.e-daewoo.com
TO CONTACT DAEWOO ELECTRONICS BY MAIL:
DAEWOO Customer Service
300-3E State Hwy Rt 17 South
Lodi,NJ 07644
Version : 2009-07-15 Rev.1
ABOUT THIS MANUAL
VISION CREATIVE. INC.
서울 종로구 통의동
6번지 이룸빌딩 4층
담
당
배상일 님
F.MODEL
B.MODEL
DWD-WD1353WC/SC/RC
언
영어
어
BUYER
DEAN
BRAND
대우일렉
COUNTRY
1차
2차
일
정
3차
4차
5차
제
판
규
격
인
쇄
애드컴
MEMO 접수 : DWD-WD136* 베이직 화일로 모델명 변경
090824 - 수정 총 2p(표지, 27)
090825 - 수정 총 1p(2)
090826 - 신규 총 2p(9,10)
- 수정 총 12p(1,4,6,7,11,12,16~20,24)
연락처
VISION
담 당
방 문 수(chois)
TEL : 730-0660 FAX : 730-3788
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement