cycle computer
(E is ||
Cros
CYCLE COMPUTER
CP-F1008
Manual
Before using the computer, please
through this manual thoroughly.
X Please keep this manual for future reference.
How to install the unit on your bicycle x
@Bracket sensor
@ Sensor rubber pedestal pad o e o pum pe ©
O Super magnet >< S make sure the
> d
ONylon ties (x9) > В does not hinder
O
7
A
(С
<
@Bracket rubber pedestal pad N AR full rotation,
(fig 3)
o
o 1
A
5
@The bracket sensor installation
Insert bracket sensor @ into speed sensor pedestal pad @
as (fig 1) shows.
(fig 4)
(fig 1)
<=
N
> Click! (({ —
Install the speed sensor , Z >
© to the front fork by ст
fastening it with the
nylon ties @ (fig 2) GE) N
8
AD Fasten the speed sensor @ loosely to adjust the position and angle.
After securing the sensor code with nylon
ties, wrap the wire of the sensor code to
the brake wire and handlebar or the handle
stem. Turn the handlebar to make sure the
sensor code does not hinder full rotation.
(fig 3)
@Install the bracket
The bracket @ can be installed on the
handiebar or handle stem<fig 4)
Set the bracket on the bracket pedestal.
Fasten the bracket to the handle bar or
handle stem with nylon ties. ¿fig 5)
"а
(fig 5)
[ Important ! ) Fasten the speed sensor @ loosely to adjust the position and angle.
When it is at the desired position, secure it by tightening the nylon ties.
Slide the computer onto the bracket until it
clicks.
When removing the computer, press the
release lever and slide it off (fig 6)
@The super magnet installation
{fig 7)
(fig 8
1 Install the magnet @ оп the front spoke so
that the face of the magnet is directed
towards the sensor surface.
Make sure that the path of the rotating
magnet @ passes the line of the speed
sensor @ (©) mark.{fig 4)
%Super magnet © is compatible with both
fiat spokes and the round spokes)
2 Adjust the distance between the super
magnet © and the speed sensor O until
that it does not exceed Smm. If the
distance is farther than 5mm, adjust the
speed sensor @ angle. (fig 8)
3 Once the installation point has been
decided, install the super magnet securely.
1 Rotate the front wheel gently to check that
the speed is displayed on the computer.
2. After checking the speed display on the
computer, adjust and cut the surplus
nylon ties @. {fig 9)
3. If the speed is not displayed on the
computer, re-adjust the installation points.
When it is at the desired position, secure it by tightening the nylon ties. (fig 6 (fig 9)
, os FE EN EN EN EN EN EN EN EN EE EN EN EN EN SE EN SN SE EN BN BN BN SN EN BN BN EN SN EN BN OOO OO OO O а “= `
! Do not concentrate on the computer while riding. ! CLEAR THE COMPUTER
! Install the magnet, sensor, and bracket securely. Check these periodically. | 1
Warning Dispose of used batteries according to local regulations. 1
1 8 1 Press the MODE button © and select
I Avoid having the computer in direct sunlight for unnecessary or extended ! pu 12HR or 24 HR.
! periods.
| /N When cleaning the computer, bracket and sensor, do not use thinners, | 2
, Caution benzene, or alcohol. I A When selecting 12 HR, select morning (A)
CNE ’ or afternoon (P) .
Adjust digit
Press the MODE button
(to select
Change screen
Press the MODE button D
to change screen
Move to
next setting
digit
Press and hold the MODE
button €) 2 secs
Reset data
Press and hold
the MODE button (1) 3 secs
(DST, CAL)
For the detail please refer
RESET DATA on the back page
Turn to
next function
Press the SET button ®to
turn to next function
Rekey data
Press the SET button ®
to enter setting mode
For the detail please refer E SET button
and operation on the back page
Quit
setting mode
Press and hold
the SET button®2 secs
O
Press the MODE button O button
ats
(a
>
«ани
Press and hold the MODE
0»
(>
(>
TE)
() for 2 seconds Press the SET button ©
to increase the value. to move to the next digit. to store the digit.
OCLEAR THE COMPUTER
1 A battery is already included in the main unit when purchased. Hold down the MODE
button 0) and SET button G)simultaneously for more than 3 seconds to initiate the
computer and clear all data.
IMPORTANT: be sure to go through the steps of initiating the computer before use,
otherwise the computer may run with errors.
2 The LCD segments will be tested automatically after the unit is initiated.
3 Press the MODE button () to stop the LCD testing, then the flickering "Km/h".
BJ UNIT SELECTION
| Clear the computer |
© O
Press the MODE button to choose
“KM/H” or “M/H”.
Then press the SET button © to store
the selection.
2 WHEEL CIRCUMFERENCE ! You can set two wheel circumferences.
Precise Measurement (Fig. a)
1 Roll the wheel until the valve stem is at its
lowest point, closest to the ground, and mark
this point on the ground.
Pr 2 Get on the bicycle and have a helper push
you until the valve stem returns to its lowest
point. Mark the second point on the ground.
3 Measure the distance between the marks by
millmeter. Enter this value (mm) to set the
wheel circumference. You can get a suitable
circumference value from the table. (Fig b)
4 Press the MODE button (Dto store the data.
5 Start setting the digit from thousandth. Press
the MODE button (Dto store the thousandth
digit, and move to hundredth and so on.
6 Once the wheel circumference has been
completed, press the SET button®to store
the data.
3
selection.
4
ЮМоуе to
ODO setting
and resetting
f=
END setting
the screen.
Press the MODE button (J) to store the
@A new user who does NOT need
to enter ODO
Press the SET button © for two seconds,
and initial setting will be completed.
@A user who NEEDS to enter ODO
Press the SET button O), and ODO
Setting and resetting mode appears on
РТ ODO Setting : total odometer setting
000000~999999
and ...
Enter the odometers as shown in the
illustration to the left.
Once all odometer data have been entered,
press the SET button © for two seconds,
initial setting will be completed.
">
