CASS HUDSON CO.
Installation Instructions Dream Dinette
(Window Version)
CASS HUDSON CO.
IMPORTANT
Ensure assembly is square, straight, and centered throughout
installation process.
Vehicle wall must be reinforced prior to installation of Dream Dinette.
Slotted holes are used in order to allow for adjustment during the
installation process. Once the mechanism is installed properly the
remaining holes should be used to secure the mechanisms in place.
This document is the property of CASS HUDSON CO. It shall not be copied or duplicated in any manner without the written consent of CASS HUDSON CO.
CASS HUDSON CO.
Dream Dinette
Table Top Preparation
• Strike a centerline
down the middle of
the table top.
centerline
This document is the property of CASS HUDSON CO. It shall not be copied or duplicated in any manner without the written consent of CASS HUDSON CO.
CASS HUDSON CO.
Dream Dinette
Attach Mechanism to Table Top
• Unfold dinette
mechanism and
install two bolts being
sure not to over
tighten.
•
•
•
Strut Location for version with
22” mounting plate.
This location is not used in this
design.
Strut Location for version with
25.5” mounting plate.
This document is the property of CASS HUDSON CO. It shall not be copied or duplicated in any manner without the written consent of CASS HUDSON CO.
CASS HUDSON CO.
Dream Dinette
Attach Mechanism to Table Top
• Turn mechanism over
on to table top.
This document is the property of CASS HUDSON CO. It shall not be copied or duplicated in any manner without the written consent of CASS HUDSON CO.
CASS HUDSON CO.
Dream Dinette
Attach Mechanism to Table Top continued
• Align mechanism so
that it is centered and
flush to the edge of
the table top.
• Ensure that the
mechanism is square,
straight, and centered
to table top then
secure using all 8
hole locations.
This document is the property of CASS HUDSON CO. It shall not be copied or duplicated in any manner without the written consent of CASS HUDSON CO.
CASS HUDSON CO.
Dream Dinette
•
•
•
Attach Slide Track and Lock Bar
Place slide track in center of
table top and adjust such that
the slide block covers
approximately 1/3 of the lock
bar window.
Secure slide track into place
using slotted holes.
Firmly press lock bar into place
and secure using hardware.
Be sure the lock bar is parallel
with the slide track and the
hardware is as far apart as
possible in order to insure
proper operation of lock.
This document is the property of CASS HUDSON CO. It shall not be copied or duplicated in any manner without the written consent of CASS HUDSON CO.
CASS HUDSON CO.
Dream Dinette
Mount Assembly
• Mount assembly to
wall being sure to
utilize all 13 mounting
holes.
This document is the property of CASS HUDSON CO. It shall not be copied or duplicated in any manner without the written consent of CASS HUDSON CO.
NOTES:
UNLESS OTHERWISE SPECIFIED
REV
A
REVISION HISTORY
DESCRIPTION
DATE
07.19.07
PRODUCTION RELEASE
APPROVED
DLS
38
36
29.4
25.5
15
11
SPECIAL NOTICE
THIS DRAWING IS THE PROPERTY OF CASS HUDSON CO. IT SHALL NOT BE COPIED OR DUPLICATED IN ANY MANNER, AND SHALL NOT BE SUBMITTED TO OUTSIDE PARTIES
FOR EXAMINATION WITHOUT OUR WRITTEN CONSENT. IT SHALL BE USED WITH REFERENCE TO WORK UNDER CONTRACT OR PROPOSALS SUBMITTED BY CASS HUDSON CO.
NAME
DATE
darrens 07/19/07
DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
ANGLES ±0.5°
2 PL ±0.03 3 PL ±0.010
CASS HUDSON COMPANY
COME ROLL WITH US
TITLE
SIZE DWG NO
DREAM DINETTE
REV
DDT255X15
B
A
FILE NAME: 255X15.dft
SHEET 1 OF 1
SCALE:
WEIGHT:
">
