CS102 Combined Spreader and Liquid controller

CS102 Combined Spreader and Liquid controller
Electro-Hydraulic Controls
CS102
Designed and Manufactured by
Combined Spreader and Liquid controller
"
Powerful design
… three controllers in one
Spreader, Pre-wet, De-ice
"
Full featured
… Pass and Blast, real time
data logging, RS232 port
"
Direct hydraulic drive
… three electro-hydraulic
drivers, adjustable PWM,
current control
"
Flexible
… open or closed loop
automatic or manual
"
Field programmable
… no special tools required.
The CS102 combines three controls into one. First as a standard spreader control the CS102 regulates granular
products using a standard conveyor (or auger) and spinner, ground speed control in pounds per mile. Secondly,
the CS102 adds a low flow liquid control in gallons per ton over the granular control for those vehicles that prewet the granular material as it exits the hopper. Third, the CS102 can control the larger liquid product pumps
required for de-icing applications, control is in gallons per mile
Features of the CS102:
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Automatic ground speed control, calibrated in true engineering units
Spreader control in pounds per mile, adjustable maximum feed rate 100 to 3000 lbs. per mile
Pre-wet liquid, ratio control in gallons per ton of granular, adjustable maximum ratio 5 to 16 gal/ton
De-ice liquid control in gallons per mile, adjustable maximum rate 10 to 500 gal/mile
Spinner control, 4 lane width selections, detented, each individually programmable, 0 to 100%
Open loop or closed loop servo drive for both granular and liquid.
Operator features; Blast, Pass, eight granular products, manual mode, English or metric
Supervisory features; Feed rate limits, manual lockout, Blast rate, material types
Data logging; records accumulated totals for each product dispensed, ten year real time clock
RS232 port for easy field upgrades using a laptop or data retrieval using a field printer, see FP100
Automatic short circuit protection, built-in diagnostics for valves and sensors
Easily programmed using the existing front panel, no special tools required, pass code protected
Optional cable; 9-pin twist lock, split loom, 15 ft valve leg, 8 ft transmission leg, pigtail ends.
One year warranty, FOB factory, Kent, WA. 98032
Electrical specification:
!
!
!
!
!
!
Operating voltage: 11-16vdc, -30 to 75 deg C operation, internally fused
Outputs: (3) current controlled PWM, high effiecency mosfet drivers, transcient suppression diodes
Inputs: (1) ac or dc type for mph, (2) current sinking for servo feedback pulse sensors
Electrical interface: AMP CPC-9 pin connector, Motiv standard pinout
Enclosure: flange mounted, painted steel, size 6.5" x 4.5" x 4.5"
Comm. port: RS232C, 9600 baud, N-8-1; 4 wire power, ground, Rx,Tx
CS102E1A
CS102
MECHANICAL
ALL DIMENSIONS ARE IN INCHES
6.5
6.0
4.5
POWER
Pre-Wet
Spread
Set PW
Off
Anti-Ice
4.5
COMM
PORT
LBS PER MILE
GAL PER MILE
CL
Prod
Cal
Man
Off 1
LANE
2
3
4
PASS
RATE
BLAST
HANDLES
CAPTIVE MOUNTING FASTENERS
PANEL SEAL
FUNCTIONAL BLOCK
GRANUAL
PWM
VEHICLE
POWER
12 vdc
Fb
CS102
PWM
Fb
DE-ICE
CONVEYOR VALVE
PUMP VALUE
SHAFT SENSOR
LIQUID FLOW SENSOR
PRE WET VALVE
LIQUID FLOW SENSOR
MPH
PWM
SPINNER VALVE
RS232
COMM PORT
CS102E1A
106 EAST TITUS ST.
KENT, WA 98032
(253) 854-1002
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement