ADC 6624-2-061-01 telephony cable

ADC 6624-2-061-01 telephony cable
LSA-PLUS®
Copper Connectivity Solutions For Telecommunication Networks
KRONE LSA-PLUS® Series 2 & avaNTi Modules and Accessories
ADC LSA-PLUS® Series 2 & LSA-PLUS® avaNTi connection systems include Connection,
Disconnection, Switching modules, MDF, Cable Termination blocks, Back-Mount frames,
protection systems, Enclosures and other related accessories.
LSA-PLUS® Overview
The LSA-PLUS® Quick Connection System offers an integrated contact for
use in all line plant and private network services.
Lötfrei Schraubfrei Abisolierfrei Preiswert Leicht zu handhaben Universell andwendbar Sicher und Schnell No solder
No use of screws
No insulation removal
Cost effective
Easy to use
Universal application
Secure and fast
LSA-PLUS® connection systems support connection, line splitting, switching and earthing of connections
in telecommunication and data networks. The contact is resistant to climatic and other environmental
conditions. Technical contact security results in the formation of a gas-tight connection with very
low transmission resistance. Special attention to maximum contact safety regardless of climatic and
ambient conditions results in high degree of technical security through gas-tight, low resistance
joint. Connection is made through the special insertion tool, assuring that the connection quality is
always repeatable.
A wide range of accessories, including overvoltage protection, marking caps and test cords ensures
that LSA-PLUS® systems can be used throughout the local loop, in main distribution frames,
cross-connect cabinets, distribution points and at the customer premises.
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
ADC LSA-PLUS® connection systems include connection and switching modules for eight or ten pairs,
all featuring the patented LSA-PLUS® insulation displacement connection (IDC) technology.
Fig- Local Loop Components
The ADC LSA-PLUS® contact functions in the same basic manner regardless of the type of module
in which it is placed. Using the LSA-PLUS® insertion tool (5), the plastic insulated copper wire or
jumper (4) is inserted into the contact slot (2). The contact slot contains contact tags (3) set at a
45-degree angle to the wire. Through the action of the tool, the contact tags twist in an axial movement
and at the same time cut through the wire insulation and push the insulation material to both sides
of the contact. Through material displacement and the subsequent torsional and restoring forces (6,7)
of the contact tags, two permanent gas-tight surface areas are formed. This connection prevents any
movement in the contact area that would undo the connection. For additional protection of the contact
area, plastic clamping ribs (1) are provided above and below the connection area. These clamping ribs
firmly grip the wire insulation, preventing any movement of the wire in the contact area. In the same
termination process, the LSA-PLUS® insertion tool cuts the wire and insulation to the correct length.
If the wire needs to be re-terminated, the LSA-PLUS® KRONE insertion tool has a swing-out hook, which
is used to remove the wire from the contact.
7
6
LSA-PLUS® Quick Connection Technique
1.
2.
3.
4.
5.
6.
7.
Plastic clamping ribs
Contact slot
Contact tags
Wire
KRONE Insertion Tool.
Torsional forces on the contact
Restoring forces of the contact
The Quick Connection Technique is a highly reliable and cost effective wire connection system for
modern telecommunications and data networks. It is a comprehensive system built around the widely
accepted ‘KRONE’ termination module with its range of built-in features. This is complemented with
an extensive selection of accessories for protection, circuit identification and testing. The LSA-PLUS®
system uses a unique Insulation Displacement Contact (IDC) technique which eliminates the need
to wire-strip, solder or make screw terminations, and dramatically increases productivity. This system
is supplied for connections in various fields like telecom and structured cabling.
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
The LSA-PLUS® Quick Connection Technique
1. Insulation clamping ribs hold wires firmly in position and isolate the contact area from vibration and other forms of mechanical stress.
2. Flexible silver-plated contacts*, positioned at 45o angle across the axis of the wire, make a solid, gas tight connection.
3. Constant axial and torsion restoring forces, created by the unique contract and plastic housing, sustains a durable connection.
Contact at 45°
Positioning the contacts at a 45o angle leaves more wire between contact points and provides a
reliable, stress resistant connection.
Contact at 90°
Positioning contacts at a 90o angle produces a point of weakness subject to possible breakage.
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
NECTION CONTACT
The 3-point Insulation Displacement Connection (IDC) method of termination gives durable and long
lasting connections.
A correctly terminated IDC prevents:
• Corrosion
• Loosening due to vibration
• High resistance connections
• Movement of the wire
If required, the connection can be redone easily and only the small portion of the wire must be
removed. The connection can only be accomplished with the KRONE insertion tool, leading to
greater contact security and assuring that when the connection is remade, no particles of insulation
or wire remain in the connection area. Most importantly, the connection is repeatable. Every time
a connection is made, the properties of the connection will be the same. The LSA-PLUS® IDC is
a reliable, secure and quick contact method. The method has been proven as an electrically and
mechanically sound method of connecting normal voice and data cabling.
DISCONNECTION CONTACT
CONNECTION CONTACT
DISCONNECTION CONTACT
S2 Disconnection Modules use a two piece contact (normally closed), with a convenient
disconnection feature. By inserting a disconnect plug into a wire pair, you can temporarily or
permanently disconnect the circuit. A Test Cord can be inserted into a pair to test each side
(look both ways) of the circuit independently. This greatly accelerates fault identification.
CONNECTION CONTACT
The centre contact point can also be used for monitoring or over voltage protection.
CONNECTION CONTACT
Connection Modules have a one piece contact providing a continuous link between
permanent wiring and jumper wiring, giving provision for monitoring access and
SWITCHING CONTACTovervoltage protection.
DISCONNECTION CONTACT
CONNECTION CONTACT
CONTACT
Features & Benefits
SWITCHING CONTACT
Switching Modules house individual contacts and hence the circuits are disconnected when
idle. By inserting plugs, cords or over voltage protection, the circuits can be connected when
necessary.
* Modules with Tin Plated contacts are also available.
Testing
ADC products and components pass through rigorous tests to maintain
a high quality standard.
ADC Tests
Quality Results
High insulation resistance is maintained even
under extremely humid conditions.
Vibration resistance test
Determines whether building vibrations and other load causes contact disturbance in the contacts. No contact disturbance observed. A high
contact and grip force is sufficient to maintain
both the connector & the connection in the defined position.
Contact pressure relief test
Simulates artificial ageing by storing the
contacts for longer periods at higher temperatures. The quality of the contact
is subsequently tested.
No change in the LSA-PLUS® contact or
housing that could impede functional
or operational reliability
Temperature shock test
Contact quality is not reduced, even under Test to determine if frictional corrosion occurs under these extreme conditions.
extreme temperature changes and whether
temperature reactions in the connector housing
has avoidable effects.
Humidity resistance test
Tests the effects of high humidity on contacts
and insulation material.
Not even high humidity affects contacts or insulation resistance.
Corrosive atmosphere test
Tests how the contacts react to the effect of
harmful gases in an aggressive industrial
atmosphere.
Most aggressive constituents in the atmosphere do not affect the quality of the contacts.
Long Term stability test
ADC creates accelerated artificial ageing processes. This provides a solid base for highly accurate reports on the service life and behaviour
of ADC contact under extreme conditions
The unrestricted service life of ADC components for the normal life of a
building/network is guaranteed
Insulation resistance test
Tests the resistance between the insulated contacts of connectors.
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
Contact resistance test
The quality of LSA-PLUS® contact is not
A reliability test that indicates the reaction of the compromised, even after repeated and
tough loads.
LSA-PLUS® contacts to a variety of test loads.
LSA-PLUS® Series 2
LSA-PLUS® ELECTRICAL DATA
After four days exposure to a climate of 40° C and 93% relative humidity
Insulation Resistance
Dielectric Strength
Current Rating
LSA-PLUS® CONTACT
Contact Resistance
≥5x104Ohms
≥2000Vrms
≥Current carrying capacity of terminated
conductor
1mΩ ≤ 5mΩ guaranteed
Total Contact Resistance including
Disconnection contacts
Contact Spring Force for Disconnecting
≤ 10mΩ
3N (approx. 300g)
contacts
Peak voltage
(with pulses 1.2/50µ sec)
≥ 3.6 V
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
Impulse current
(with pulses 8/20 µ sec)
5 kA
Number of Re-Terminations
≥200
≤1pF
Thermoplastic (PBT) UL 94, V-0
≥28%
Coupling Capacitance Between Wires.
Plastic Housing Material
Oxygen Index
LSA-PLUS® TECHNICAL DATA
Disconnection, Connection, Switching and Earth Modules for Plastic Insulated Copper Conductors
Insulation Diameter
0.40 - 0.80mm. (AWG 26 - 20)
7/0.2 - 7/0.32mm
0.70 - 1.50mm
Number of Equal Diameter
2 max. (up to 0.65mm each)
Copper Conductor Diameter
Multistrand Conductor
Solid Conductors Per Slot
Number of Equal Diameter
1 max.
Multistrand Conductors Per Slot
ENVIRONMENTAL DATA
Environment for use
Indoors or enclosed cabinets outdoors with a
minimum degree of protection to IP54 (IEC-529)
Storage temperature
Operating temperature
Max. operating humidity
-40° to +90°C
-20° C - +80° C
93% relative humidity non-condensing
Installation for LSA-PLUS® S2 Modules
1. Fix the back mount frame in a vertical position on the MDF/
Exchange Room and ensure a safe earth connection is established,
through the Bus Bar.
2. Introduce cable and strip
the sheath (free conductor length should equal
distance of furthest
module+200MM).
Then secure cable to the MDF Frame.
4. Termination of wires.
a. Choose the bottom most slots on MDF to fit
module.
b. Hold the module about 50 mm - 80 mm from
allocated position on the back mount frame.
c. Push wire bundle at lease 150 mm through the module guide loop in the direction
of the permanent side and retain by bending wires over.
d. Place module in allocated position (surplus wire in a loop).
e. Pull wires between the guide notches and lay it into the contact slots.
f. Terminate wires with the 'KRONE' Insertion Tool. Discard surplus wire.
g. Repeat procedure by fixing modules from bottom to top.
5. Jumpering
a. Press jumper wires into the bottom row of
contact slot (jumper side) and connect using
the 'KRONE' Insertion Tool; (Pair 1-5 to the
left side, pair 6-10 to the right side).
b. Lead jumper wires through jumper guide/
ring on either side of the module as
required.
6. Wire can be removed using hook housed at
the side of the 'KRONE' Insertion Tool.
7. To remove the module from backmount frame use the
swing-out module extractor on the 'KRONE' Insertion tool.
Press tags on backmount frame inwards at both
ends and pull module forwards.
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
3. Form wires into 10-pair groups for each allocated
position, by bringing inside the frame, through the
cable entry holes.
LSA-PLUS® avaNTi
FEATURES & BENEFITS
The Space Saver
The expansion of mobile communication networks, the introduction of third generation mobile phone
systems (3G, UMTS) and the steady growth of IP networks, have created a demand for bandwidth
Space
in both access and transmission networks. This 30%
in turn causes
the extension of existing hubs and the
installation of new hubs.
Savings
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
As a Telecom service provider, one of your prime concerns is to enhance your connection density.
While you work towards achieving your goal of adding more connections, you must equip yourself
with a connection system that meets the needs of Next Generation Networks. The first step towards
a well-built network is to have a strong basic building block: a smart, next generation disconnection
module-The LSA-PLUS® avaNTi.
30% Space
Savings
The LSA-PLUS® avaNTi helps save space and
cut costs in comparison to a traditional MDF
(Main Distribution Frame) thus broadening
your network resulting in increased bottom
line. The LSA-PLUS® avaNTi is an easy-to-use
disconnection module that features a high
connection density and requires only the
traditional ADC LSA-PLUS® insertion tool to
get it connected.
Saves space.
Stabilizes performance.
Improves efficiency.
Saves money.
Easy to use.
Saves space.
Stabilizes performance.
Improves efficiency.
Unique Design, built for ease-of-use.
Saves money.
• The system
sideto
is situated
Easy
use. at the back at a right angle
- no accidental access.
• The test access and the jumper contacts are accessible
from the front and very clearly arranged
- User-friendly activation
• The modules are designed for mounting onto
back-mount frames
• Compact MDF Tag blocks
• The cable wires are fed in from the back or from the side so that
when the module has been installed, only the jumper wires
are directly accessible.
• For any work on the cable side, the module can always
be released from its installed position so that new
wiring work can be done.
• The jumper space between the modules is just
large enough to accommodate the cable and
jumper sides in different planes.
• Despite the generous jumper channels, the modules are mounted with a bare minimum
pitch of 17.5mm.
•
The LSA-PLUS® avaNTi tag block for 100/64/128 pair comprises of 10/8 pair modules, set of side
mount label holders, number plugs, stainless steel back-mount frame and fixing elements. The
modules are mounted on the back mount frame and can beinstalled on the MDF verticals or cross
connection cabinets/pillars. The module pitch is 17.5mm which contributes to a space saving of
about 30%
• The LSA-PLUS® avaNTi offers 4-pole test cords, special cords with over voltage protection for test purposes. On one end is a plug designated for the LSA-PLUS® avaNTi module, equipped with a snap-in element. On the other end are 2 or 4 sockets for 4mm plugs (banana plugs).
The 4-pole cord has been especially designed to measure the incoming or outgoing
signals in the LSA-PLUS® avaNTi disconnection modules.
•
The LSA-PLUS® avaNTi is equipped with single pair protection plug fitted with 3-pole GD tube
and PTC resistors for over voltage and over current protection. This acts as a complete protection
component, which, when inserted into the LSA-PLUS® avaNTi disconnection module, achieves
complete protection meeting ITU K.12 and K.20 standards.
Backmount frame options
Enhanced Efficiency
The LSA-PLUS® avaNTi can be used to enhance your efficiency levels multifold.
The various areas of its application are:
•
•
•
•
•
•
•
At sites where many copper wires have to be distributed
In high density MDF`s (1600 pairs in 3.5 meters or 1000 pairs in 2.2 meters)
At sites where active components also have to be installed and space becomes premium.
For eg. DLC's, ONU's
In cross connection cabinets
In co-location rooms where there is very little space available
Where access to the module's cable side needs to be restricted
In co-location rooms, individual access for operators required for switching work, without access to cabling of other operators
Security features for protection
•
•
•
•
•
It protects your cable wiring from accidental access during jumper work
It provides you with a secure investment for the future
30% less mounting pitch (17.5mm) than that of traditional Series 2 modules for cross
connection cabinets, without any loss in robustness
High degree of modularity in arrangement
Connection errors completely avoided
Identification and Marking Facilities
The side label holders fixed on the right hand side jumper guide of the module fitted with
plug numbers serves to identify cable pairs as well as the block. The top label holder is in black
colour and bottom most in red. The rest are in grey colour for easy identification of block in a
1600/1000 pair MDF verticals. Red coloured marking caps are available for marking important
jumper pairs wherever required. Dummy plugs are available to prevent accidental disconnection
of important lines. Disconnection plugs are available to disconnect lines from the active network.
a.Custom built frames of arbitrary length.
b.Standard Back mount frame as below:
10 way for 100 pair block
8 way for 64 pair block
16 way for 128 pair block
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
Two forms of backmount frames are available:
TECHNICAL DATA
Module Specifications
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
Contact Resistance Insulation Resistance
Plastic
Contact Material
Contact Re-Terminations Conductor Diameter Range
Insulation Diameter Range
Operational Temperature
Mounting Pitch
Contact Stability
Electrical safety
Product
Width
Height
Depth
LSA-PLUS® avaNTi module
100 pair MDF tag block
100 pair MDF tag block with protection
64 pair MDF tag block
128 pair MDF tag block
130.0
130.0
130.0
130.0
130.0
17.5
180.0
180.0
145.0
285.0
40.0
70.0
105.0
70.0
70.0
Product Dimensions (in mm)
Single Pair Protection Plug for avaNTi MDF (1600 pairs Per vertical)
Max. Operating voltage (a/b-e, a-b) Vmax,e
Nominal DC spark-over voltage Vsdcn
Impulse spark-over voltage @1 kV/μs (a/b-e)
Impulse life time (300 times 10/1000μs, alternating polarity)
Nominal arrester surge current (8/20 μs; a/b-e)
Nominal arrester alt. discharge current (50hz,1s; a/b-e)
Fail safe response time @ 5 Arms
Max. Operating current (a-a’/b-b’) @ 25°C
Rated line resistance (a-a’/b-b’) @ 145mA, 25°C
Resistance balance
Max. Switching Current of PTC @ Vmax=230Vrms
Max. Switching Time of PTC @ 1Arms
Capacitance (1MHz/1Vrms; a/b-e, a-b)
Insulation resistance @ 100V(a-b, a-e, b-e)
Operating temperature
Storage temperature
Electrical characteristics
Mechanical characteristics
Climatic characteristics
Circuit Diagram
≤2.5 mΩ
>50000 MΩ
PBTP UL94 Rated VO
Brass Alloy
0.4mm (26 AWG) 1 conductor per contact ≥ 200 re-terminations
0.5mm (24 AWG) 1 conductor per contact ≥200 re-terminations
0.63mm(22 AWG) 1 conductor per contact ≥200 re-terminations
0.4 to 0.63mm
0.7 to 1.5mm
-20 to +80ºC
17.5mm
satisfying IEC 352 Part 4
satisfying EN 60950, Conforms to CE low-voltage guidelines
180 V
180-300 V
<900 V
100 A
5 kA
5 Arms
<5 Secs
120 mA
6-25 Ω
<0.5 Ω
3 Arms
2.5 Secs
<1.50 pF
>1000 MΩ
-20°…+60°C
-40°…+80°C
ITU-T K.12 compliant
Sinusoidal wave acc. To IEC 68-2-6
DIN IEC 68 part 2-2/3 (thermal resistance)
DIN IEC 68 part 2-1(cold resistance)
Component Dimensions
Ordering Information
LSA-PLUS® Series 2 Modules and Accessories
MODULES
KRONE LSA-PLUS® Series 2 Disconnection Module
Disconnection module for 8/10 pair with disconnection contact.
Disconnect contact used for opening the circuit. Testing is possible
in both directions. Can accept 3 or 5 point protection elements.
10 Pair
8 Pair
Ordering Information
Pack Qty.
Product No.
KRONE LSA-PLUS® Series 2 Disconnection Module 2/10
1
6089 2 011-02
KRONE LSA-PLUS® Series 2 Disconnection Module 2/8
1
6036 2 002-00
KRONE LSA-PLUS® Disconnection Module 2/5
Disconnection module for 5 pair with disconnection contact. Disconnect
contact used for opening the circuit. Testing is possible in both directions.
Ordering Information
Description
Pack Qty.
KRONE LSA-PLUS® Series 2 Disconnection Module 2/5
1
Product No.
6904 2 204- 00
KRONE LSA-PLUS® Earth Module
For connecting drain wires to an earth contact
without soldering, wire-stripping or the use of screws.
Ordering Information
Description
KRONE
LSA-PLUS®
Pack Qty.
Earth Module 2/30
KRONE LSA-PLUS® Earth Module 2/38
Product No.
1
6036 2 006-00
1
6089 2 017-07
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
Description
BACK MOUNT FRAME
Back Mount Frame CT Block
Back Mount Frame 2/10 for cabinets and pillars. For mounting
LSA-PLUS® modules 2/10.
Ordering Information
Description
Pack Qty.
Product No.
Back Mount Frame 2/10 6 way
1
6901 2 006-14
Back Mount Frame 2/10 11 way
1
6901 2 006-13
Back Mount Frame Series 2 for 2/8 and 2/10 modules
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
Back Mount Frame (stainless steel) 2/10 or 2/8 to mount LSA-PLUS®
modules. For indoors, you can use directly on to MDF’s, Walls, Wall
Mount Frames, boxes. For outdoors, you can use it on weather proof
out door distribution boxes.
Ordering Information
Description
Pack Qty.
Product No.
Back Mount Frame 2/10, 1 way
1
6442 3 230-01
Back Mount Frame 2/10, 2 way
1
6050 3 230-02
Back Mount Frame 2/10, 3 way
1
6050 3 230-03
Back Mount Frame 2/10, 5 way
1
6050 3 230-05
Back Mount Frame 2/10, 10 way
1
6442 3 230-10
Back Mount Frame 2/10, 11 way
1
6442 3 230-11
Back Mount Frame 2/8, 9 way
1
6441 3 230-09
Back Mount Frame 2/8, 17 way
1
6441 3 230-17
MDF (Main Distribution Frame) TAG BLOCKS
MDF Tag Block 100 pair
MDF Tag Blocks 2/10 for 100 pair with 10 LSA-PLUS® disconnection
Modules for use on “Line Side“ (subscriber) of MDF’s.
Ordering Information
Description
Pack Qty.
Product No.
MDF Tag Block 22.5 mm. Pitch
1
6901 1 001-01
MDF Tag Block 25 mm. Pitch
1
6901 1 001-11
MDF Tag Block 64 & 128 Pair
MDF Tag Blocks 2/ 8 for 64 pair with 8 LSA-PLUS® disconnection
Modules for use on “Exchange Side“ (Switch) of MDF’s.
Ordering Information
Description
Pack Qty.
Product No.
MDF Tag Block 64 pair
1
6901 1 002-11
MDF Tag Block 128 pair
1
6901 1 102-11
64 Pair
128 Pair
CT Block for cross connect cabinets
Ordering Information
Description
Pack Qty.
Product No.
CT Box,100 pair connection modules
1
6901 1 006-00
CT Box,100 pair disconnection modules
1
6901 1 106-02
CT Box, 50 pair connection modules
1
6901 1 107-01
CT Box, 50 pair disconnection modules
1
6901 1 107-02
PROTECTION SYSTEMS
Over voltage and Over current protection components that satisfies all safety requirements of
modern telecommunication systems.
Single Pair Protection Plug (IPM)
This provides both voltage and current protection for
single pair on line side. The primary protection is built in
by 3 pole GD Tube. The over current protection is provided
by Positive Thermal Coefficient resistor (PTC).
Ordering Information
Description
Pack Qty.
Product No.
Earth Bar 2/10
1
69053320-00
Single pair protection plug
1
6905 2 604-01
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
CT Blocks for 100 and 50 pairs, for pillars and cross connect cabinets with
LSA PLUS® disconnection or Connection modules.
Protection Magazine 10 pair
This provides voltage protection for 10 pairs on line side.
The magazine can house up to ten 3 pole GD Tubes.
Ordering Information
Description
Pack Qty.
Magazine 10 pair
Product No.
1
6089 2 023 -01
ACCESSORIES
Accessories for testing telephone lines, local loop. Label holders, marking caps & disconnection plugs.
TestCords
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
Test Cords help test telephone lines and loop testing
from subscriber end to exchange side MDFs.
Test Cord
Connection Cord
Open Ended
Ordering Information
Description
Test Cord 2/2, 2 pole open ended with 1 plug 2/2
1.5m
3.0m
6.0m
Test Cord 2/2, 2 pole with 2 banana Plugs
1.5m
3.0m
6.0m
Connection Cord 2/2 2 pole with Plugs 1.5m
3.0m
6.0m
Test Cord 2/4, 4 pole open ended with 1 plug 2/4 1.5m
3.0m
6.0m
Test Cord 2/4, 4 pole with 4 banana Plugs 1.5m
3.0m
6.0m
Connection Cord 2/4 4 pole with 2 plug 1.5m
3.0m
6.0m
Pack Qty. Product No.
1
1
1
6624 2 071-00
6624 2 071-03
6624 2 071-06
1
1
1
6624 2 061-00
6624 2 061-03
6624 2 061-06
1
1
1
6624 2 081-00
6624 2 081-03
6624 2 081-06
1
1
1
6907 2 001-00
6907 2 001-03
6907 2 001-06
1
1
1
6907 2 501-00
6907 2 501-03
6907 2 501-06
1
1
1
6907 2 301-00
6907 2 301-03
6907 2 301-06
Disconnection Plugs
Used for disconnecting single subscriber line or for simultaneous
disconnection of all subscriber lines in LSA-PLUS® disconnection
module 2/10.
Ordering Information
Description
Pack Qty.
Product No.
Disconnection Plug 1 pair
1
6089 3 055-00
Disconnection Plug 10 pair
1
6089 3 130-01
Marking Caps
Ordering Information
Description
Marking Caps
Pack Qty.
1
Product No.
6089 3 006-00
Dust Cover
This dust cover protects the LSA-PLUS® module
installations in groups of 100 pairs against destructive
dust deposits.
Ordering Information
Description
Pack Qty.
Product No.
Dust Cover 2/10 deep, for 100 pairs
1
6092 3 034-00
Dust Cover 2/10 flat, for CT Block
1
6092 3 016-00
Label Holder
Directly mounted on to the Back Mount Frame. Fixing on the first
or last position on the BMF is recommended.
Description
Ordering Information
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
Single Pair marking cap for marking important
lines in LSA-PLUS® connection or disconnection
modules 2/10.
Pack Qty.
Product No.
Label Holder 2/10
1
6092 2 012-01
Label Holder 2/8
1
6901 2 010-02
Plug Numbers
For identification of LSA-PLUS® S2 modules.
Ordering Information
Description
Pack Qty.
Printed 0...9
1
6900 3 017-00
Product No.
Printed 10...100
1
6900 3 018-00
KRONE* Insertion Tool
The insertion tool can be used for terminating wires
(jumper and UGC). It can also be used to remove modules
and wires from tag blocks.
Ordering Information
Description
Pack Qty.
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
Insertion Tool
1
Product No.
6089 2 003-00
INDOOR DP BOXES
Kronnection Boxes
Kronnection Boxes are available in three compact sizes suitable for surface
installation. Boxes are made up of a self extinguishing polystyrene material.
Ordering Information
Description
Pack Qty.
Product No.
Kronnection Box I, 30 pair
1
6436 1 013-20
Kronnection Box II, 50 pair
1
6406 1 015-20
Kronnection Box III, 100 pair
1
6437 1 020-20
Metal Connection Boxes
Metal Boxes are available in three compact sizes suitable for surface installation.
Boxes are made of CRCA sheet and come with a powder coating.
Ordering Information
Description
Pack Qty.
Product No.
Metal connection box 30 pair
1
6901 1 500-01
Metal connection box 50 pair
1
6901 1 500-02
Metal connection box 100 pair
1
6901 1 500-03
* Modules to be ordered seperately
OUTDOOR / INDOOR BOXES
Kronnection Box A-30
The Kronection Box A-30 is designed to accommodate up to 30 pairs both in indoor
and outdoor installation. They are made of glass fiber reinforced polyester. It protects
the installed devices against dust and rain water (protection according to IP 54). The
box can be mounted directly on the wall or on a pole with a pole mounting bracket.
Ordering Information
Description
Pack Qty.
Box A-30
Product No.
1
6902 1 001-42
This type of frame has the module installation for the line and system
sides vertically in a single profile frame.
This allows jumpering within a single vertical row.
•
•
•
Advantages:
Modular, space-saving installation
Optimal adaptation to available space
Minimal installation time, since the frame is delivered pre-assembled
MDF frame to terminate 1000 pairs, 3.5 meters
Preferred frame variant for 1000 pairs for accommodation of 10 pair LSA-PLUS®
modules on the line side and 8 pair LSA-PLUS® module horizontally on the
system.
Ordering Information
Description
Pack Qty.
Product No.
Set of 5 verticals (Main)
1
6901 2 100-05
Set of 4 verticals (Main)
1
6901 2 100-04
Set
of Frame
3 verticals
(Expansion)
MDF
to terminate
1000pairs, 3.5 meters 1
6901 2 003-03
Set of 2 vertical (Expansion)
6901 2 100-02
1
1250
1020
LINE SIDE
(vertical)
EXCHANGE SIDE
(horizontal)
16
13
15
12
14
11
13
10
12
11
9
4500
10
8
3500
9
7
8
~ -3175
7
6
6
5
5
4
4
3
2
225
3
2
1
400
1
250
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
Main Distribution Frames
550
>1250
MDF Frame to terminate 1000 pairs, 3.5 meters
MDF frame to terminate 600 pairs, 3.2 or 2.2 meters
Preferred frame variant for 1000/600 pairs for accommodation of 10 pair LSA-PLUS® modules
on the line side and 8 pair LSA-PLUS® module horizontally on system side.
Ordering Information
Description
Pack Qty.
1
6901 2 600-15
Set of 4 verticals (Main)
1
6901 2 600-04
Set of 3 verticals (Expansion)
1
6901 2 600-03
Set of 1 vertical (Expansion)
MDF Frame to terminate 1000/600pairs, 3.2 meters
1
6901 2 600-02
LINE SIDE
(vertical)
EXCHANGE SIDE
(horizontal)
13
10
12
9
11
10
8
9
8
6
3500
5
6
5
~ -3175
7
4
4
3
3
2
225
2
1
1
400
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
4500
7
Product No.
Set of 5 verticals (Main)
250
550
>1250
MDF Frame to terminate 1000/600 pairs, 3.2 meters
Ordering Information
LSA-PLUS® avaNTi Modules and Accessories
MODULES
LSA-PLUS® avaNTi Modules
Disconnection module for 8/10 pair with disconnection contact.
Disconnect contact used for opening the circuit. It can accept
3 or 5 protection elements.
Ordering Information
Product No.
1
6904 2 501-01
LSA-PLUS® avaNTi Disconnection Module 2/8
1
6904 2 502-01
MDF Tag Blocks
MDF Tag Blocks 2/10 for 100 pair with 10 avaNTi disconnection
modules for use on “Line Side“ (subscriber) of MDF’s
Ordering Information
Description
LSA-PLUS®
avaNTi MDF Tag Block 100pair Pack Qty.
1
Backmount Frames
Backmount Frame to mount avaNTi modules 2/8 or 2/10. In indoors,
use directly on the MDF, Walls, Wall Mount Frames, boxes as well as
weather proof out door distribution boxes.
Ordering Information
Description
Backmount Frame, 3 way
Pack Qty.
1
Product No.
6905 3 436-03
Backmount Frame, 8 way
1
6908 3 436-08
Backmount Frame, 10 way
1
6908 3 436-10
Backmount Frame, 16 way
1
6908 3 436-16
Product No.
6901 1 103-11
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
Pack Qty.
LSA-PLUS® avaNTi Disconnection Module 2/10
Description
MDF Tag Blocks
MDF Tag Blocks 2/ 8 for 64/128 pair with 8 avaNTi disconnection
modules for use on “Exchange Side“ (Switch) of MDF’s
Ordering Information
Description
Pack Qty.
Product No.
LSA-PLUS® avaNTi
MDF Tag Block 64 pair
1
6901 1 103-12
LSA-PLUS® avaNTi
MDF Tag Block 128 pair
1
6901 1 103-13
Protection
This provides both over voltage and over current protection for single pair on line side.
Ordering Information
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
Description
Pack Qty.
Single pair protection plug
1
6905 2 609-02
Set of 10 with Earth bar
1
6905 1 609-02
Earth bar
1
6905 3 609-03
Accessories
KRONE Insertion Tool
The insertion tool can be used for terminating wires (jumper and UGC).
It can also be used to remove modules and wires from tag blocks.
Ordering Information
Description
Insertion Tool
Pack Qty.
1
Product No.
6089 2 003-00
Test Cord
Test Cords help test telephone lines and loop testing
from subscriber end to exchange side MDFs.
Ordering Information
Description
Product No.
Pack Qty.
Product No.
Test Cord 2/4 4 pole with protection - 6mtrs
1
6907 2 703-06
Test Cord 2/4 4 pole with 4 banana plugs - 1.5 mtrs
1
6907 2 702-00
Test Cord 2/4 4 pole with 4 banana plugs- 6mtrs
1
6907 2 702-06
* Modules to be ordered seperately
Disconnection Plug
Used for disconnecting single subscriber line or for
simultaneous disconnection of all subscriber lines in LSA-PLUS®
avaNTi disconnection module 2/10. Single Pair marking cap for
marking important lines in LSA-PLUS® avaNTi connection
or disconnection modules 2/10.
Ordering Information
Description
Pack Qty.
Product No.
Disconnection Plug 1 pair (red)
1
6904 3 501-16
Disconnection Plug 10 pair (grey)
1
6904 3 501-18
Marking cap1 pair (red)
1
6089 3 006-00
Dummy plug 1 pair (black)
1
6904 3 501-17
Ordering Information
Description
LSA-PLUS® avaNTi termination outrigger
Pack Qty.
1
Product No.
6901 3 007-44
The LSA-PLUS® avaNTi termination outrigger is helpful in terminating
ground cable on the module with ease.
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
Wiring Accessories for BMF (Back Mount Frame)
Main Distribution Frames
MDF is the interface between the subscriber cables coming from the local network (line side) and
the switching equipment in the exchange (system side). ADC MDFs are available in a free standing
version. (On request available in wall-secured version too).
The MDFs are delivered pre-assembled thus minimising installation time.
MDF Frame to terminate 1600 pairs*, height 3.5 meters
Ordering Information
Pack Qty.
Product No.
Set of 5 verticals (Main)
1
6901 2 164-05
Set of 4 verticals (Main)
1
6901 2 164-04
Set of 3 verticals (Expansion)
1
6901 2 164-03
Set of 2 vertical (Expansion)
1
6901 2 164-02
MDF frame to terminate 1000 pairs*,height 3.5 meters
Ordering Information
Description
Pack Qty.
Product No.
Set of 5 verticals (Main)
1
6901 2 162-05
Set of 4 verticals (Main)
1
6901 2 162-04
Set of 3 verticals (Expansion)
1
6901 2 162-03
Set of 2 vertical (Expansion)
1
6901 2 162-02
MDF frame to terminate 1000 pairs*, height 2.2 meters
Ordering Information
Description
Pack Qty.
Product No.
Set of 5 verticals (Main)
1
6901 2 163-05
Set of 4 verticals (Main)
1
6901 2 163-04
Set of 3 verticals (Expansion)
1
6901 2 163-03
Set of 2 vertical (Expansion)
1
6901 2 163-02
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
Description
* As per TEC spec
KRONE type is NOT KRONE*
It is observed that there are duplicates of original KRONE* products being sold in the market passing off as original
KRONE* products. Using these duplicate products affects the functionality and quality of your network. Please
ensure you use original KRONE* products for an efficient network. Original KRONE* products are sold ONLY
through authorised distributors*.
In accordance with TEC specifications, KRONE* MDF’s are supplied as a package unit which includes the
frames, line and exchange side tag blocks, IPM’s for protection, insertion tools and test cords and disconnection
plugs. This is done because the design ensures 100% compatibility of accessories provided by KRONE with the
KRONE* MDF’s.
Original KRONE IPMS
with original KRONE blocks
Original KRONE IPMS with
'KRONE TYPE' blocks
Original KRONE block with
competitor IPMS

LSA-PLUS® Series 2 & avaNTi Modules and Accessories
These pictures demonstrate how a duplicate (also
known as ‘KRONE type’) Tag Block/IPMS when used
with KRONE IPMS/Tag Block affect the functionality
of the product.
KRONE Communications Ltd is now ADC India Communications Ltd. However some of the
products and accessories (ie: Modules, tag blocks etc) continue to carry the famous brand name ‘KRONE’
* Visit www.adc.com/in for a list of ADC’s authorised Distributors.
LSA-PLUS® Series 2 & avaNTi Modules and Accessories
www.adc.com/in
Corporate Office & Factory: P B No. 5812, 10 ‘C’ II Phase, Peenya, BANGALORE - 560 058. India
Ph: +91 80 2839 6101 / 6291, Fax +91 80 2372 2753 Toll Free: 1800 425 8232
For a listing of ADC India's sales office locations, please refer to our website
ADC Telecommunications, Inc., P.O. Box 1101, Minneapolis, Minnesota USA 55440-1101
Specifications published here are current as of the date of publication of this document. Because we are continuously
improving our products, ADC reserves the right to change specifications without prior notice. At any time, you may
verify product specifications by contacting our headquarters office in Minneapolis. ADC Telecommunications, Inc.
views its patent portfolio as an important corporate asset and vigorously enforces its patents. Products orfeatures
contained herein may be covered by one or more U.S. or foreign patents. An Equal Opportunity Employer
400255IN 06/10
Revision 1
© 2010 ADC Telecommunications, Inc. All Rights Reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement