INSTALLATION AND WIRE

CONNECTION MANUAL

1. SAFETY PRECAUTIONS

❏

Symbol Identification

This manual uses symbols and icons to indicate safety precautions and concerns during the installation procedure. Be sure to carefully read and understand each precaution prior to beginning the installation.

WARNING

• This symbol is intended to alert the user to the presence of important operating instructions. Failure to heed the instructions may result in severe injury or death.

CAUTION

• This symbol is intended to alert the user to the presence of important operating instructions. Failure to heed the instructions can result in injury or material damage.

❏

Before Use

WARNING

• Confirm the battery voltage of the vehicle to be installed. This unit is designed only for vehicles with DC

12V power supply.

• Disconnect the negative terminal of the battery before connecting wires, otherwise an electric shock, injury by short circuit may occur.

Car battery

❏

Installation Precautions

WARNING

• When installing the unit to a vehicle with an airbag system, never install it in a place where it may affect the operation of the airbag.

• Do not install this unit in the following locations:

A location interfering with the driver’s visual range or operation.

A location where the gear shift or brake pedal are hindered.

A location where passengers are at risk.

An unstable location, or where the system may fall.

CAUTION

• Do not install the system in the locations described below. This may cause a fire, accident or electrical shock:

A location exposed to rain or dust.

An unstable location, or where the system may fall.

• Do not install this unit in a place exposed to direct sunlight, heat or a place where the vent holes or heat radiation holes are covered.

• When you install the antenna, mount it in a place where the elements of the antenna do not protrude beyond the edge of the front, back, left and right of the vehicle.

If it comes in contact with pedestrians, it may cause an accident.

❏

Installation Notes

WARNING

• Please note the position of pipes, tanks and electrical wirings before installing the unit into the vehicle; failure in avoiding these may cause a fire or malfunction.

CAUTION

• Use only the supplied parts.

If unspecified parts are used, they may cause damage.

• Any holes made in the body of the vehicle should be sealed with a silicon adhesive.

If exhaust fumes or water penetrates into the vehicle, this may cause an accident.

• Fasten the bolts securely when installing the unit. If the bolts are loose an accident or malfunction could occur.

❏

Connection Notes

WARNING

• Loom all cables according to the instruction manual, so as not to hinder operation.

• Wire the connecting cords/cables away from high temperature areas.

If the coatings of the cables melt, it could cause an accident/fire by a short circuit.

Take care when wiring in the engine compartment.

• When wiring the connecting cables in a vehicle with an airbag system, never feed the cables through a place where it may affect the operation of the airbag.

An airbag not operating correctly in an emergency may cause increased injury.

NX604/FX503 57

CAUTION

• Verify wires with a digital multi-meter prior to making any connections.

Many new vehicles use multiplexed and/or low voltage circuits that can be damaged if a test light or logic probe is used.

• Connect cables appropriately. If a wrong connection is made, this may cause a fire or accident.

• When passing cables through the body of the vehicle, use nonconductive grommets.

If the coatings of the cables are worn out by rubbing, this may cause an accident, fire or a short circuit.

• After wiring cables, fix them with insulation tape.

• Be sure to switch off the vehicle when connecting or disconnecting cables to/from the unit, otherwise an electric shock, injury or accident may occur.

2. PACKAGE CONTENTS

Main unit

Quick Start Guide & Installation

Manual

CD-ROM

• Owner’s manual

• Owner’s manual - Navigation (NX604 only)

Power supply cable

RCA pin cable (6ch)

RCA pin cable (Rear AUX-IN/Rear

Video Out)

Bag for accessories

• Flat head screw (M5 × 8 mm)

............................................................8

• Hexagonal bolt (M5 × 8 mm)

............................................................8

• Rubber cap (for RCA pin cable)

..........................................................10

• Cable holder (NX604 only)

���������������� 3

• Double-sided tape for fastening GPS antenna (NX604 only)

���������������� 1

• Cable tie ������������ 1

Finisher

Warranty card

GPS antenna (NX604 only)

USB Cable

Microphone (NX604 only)

Notice

• The provided disc (CD-ROM manual) cannot be played back on this unit.

3. GENERAL CAUTIONS

● Do not open the case. There are no user- serviceable parts inside. If you drop anything into the unit during installation, consult your dealer or an authorized

Clarion service center.

4. CAUTIONS ON INSTALLATION

● Prepare all articles necessary for installing the main unit before starting.

● Install the unit within 35° of the horizontal plane. (Figure 1)

Max. 35°

5. INSTALLING THE MAIN UNIT

This unit is designed for fixed installation in the dashboard.

● When installing the main unit in NISSAN vehicles, use the parts attached to the unit and follow the instructions in Figure

3.

When installing the main unit in TOYOTA vehicles, use the parts attached to the vehicle and follow the instructions in

Figure 4.

● Wire as shown in Section 9 → P.61.

● Reassemble and secure the unit in the dashboard and set the face panel and center panel.

Mounting Screw Holes (Side View of the Main Unit)

Figure 1

● If you have to do any modification on the car body, such as drilling holes, consult your car dealer beforehand.

● Use the included screws for installation.

Using other screws can cause damage.

(Figure 2)

Chassis Chassis

Damage

Max. 3 mm (M4 screw)/

Max. 8 mm (M5 screw)

Figure 2

For NISSAN vehicle

For TOYOTA vehicle

58 NX604/FX503

❏

Installing the Main Unit in a NISSAN Vehicle

❏

Installing the Main Unit in a TOYOTA Vehicle

Install by using parts attached to the vehicle. (Screws marked are attached to the vehicle.)

Main Unit 6-Spacer (thickness: 1 mm)

Main Unit

8-Hexagonal screw

(M5 x 8)

Finisher ✽ 1

Mounting bracket

(1 pair for the left and right sides)

Figure 3

6-Flat head screw

(M5 x 8)

(attached to the main unit)

✽ 1 Position the face panel with its wide edge at the bottom. Fit the edge into the groove of the main unit.

Center Panel ✽ 2

✽ 3

Mounting bracket

(1 pair for the left and right sides)

Figure 4

✽ 2 Some panel openings are too small for the unit depending on the vehicle type and model. In such a case, trim the upper and lower sides of the panel frame by about 0.5 to 1.5 mm so the unit can be inserted smoothly.

✽ 3 If a hook on the installation bracket interferes with the unit, bend and flatten it with a nipper or similar tool.

Typical Mounting Brackets

Example 1 Example 2

Affix the screws to the marks.

Example 3

NX604/FX503 59

❏

Vehicles other than NISSAN and TOYOTA

In some cases the center panel may require modification. (Trimming, filing, etc.)

6. REMOVING THE MAIN UNIT

When the main unit is to be removed, disassemble it in the reverse of the order in

“INSTALLING THE MAIN UNIT”. → P.58

7. CAUTIONS ON WIRING

● Be sure to turn the power off before wiring.

Be particularly careful where you route the wires.

● Keep them well away from the engine, and exhaust pipe, etc. Heat may damage the wires.

● If the fuse should blow, check to see if the wiring is correct.

If a fuse is blown, replace it with a new one of the same specification as the original.

● To replace the fuse, remove the old fuse of the power supply cable and insert the new one. (Figure 5)

Fuse (15A

FUSE)

Fuse holder

Figure 5

● There are various types of fuse holder.

Do not let the battery side touch other metal parts.

CAUTION

• After connecting the HDMI and USB cables to the unit, use a cable tie to tie them down. (Figure 6)

Cable tie

HDMI

Cable

Figure 6

USB Cable

8. INSTALLING THE GPS ANTENNA (NX604 ONLY)

WARNING

• Do not install the GPS antenna in a place where it may interfere with the operation of the airbag or hinder the driver’s visual range.

• Do not use the navigation system with the GPS antenna cable cut off. The power line in the cable may be short-circuited.

● The supplied GPS antenna is for installation inside the vehicle. Do not install it outside the vehicle.

● Install the GPS antenna more than 19.7in (50 cm) away from the main unit, other audio devices such as CD player, and a radar detector. If it is installed near these devices, GPS reception may be impaired.

● To improve the GPS signal reception, install the GPS antenna horizontally on a flat plane.

● Do not wax or paint the cover of the GPS antenna. This may reduce the performance of the GPS antenna.

● Install the GPS antenna at least 3.9in (10 cm) away from the windshield.

● Wipe off the dirt of the mounting surface before installing the GPS antenna.

● Stick the double-sided tape to the bottom face of the GPS antenna.

Double-sided tape

Bottom face of the GPS antenna

60 NX604/FX503

● Mount the GPS antenna.

Stick it surely on a flat plane of the passenger-side dashboard where GPS signal interruption is minimized.

● Wire the GPS antenna cable.

Fasten the cable using the Cable holders.

GPS antenna

Cable holder

9. WIRE CONNECTION

Radio antenna jack

GPS antenna jack (NX604 only)

Rear Vision

Camera terminal

Refer to the following page.

USB terminal

HDMI cable

(sold separately)

HDMI/MHL conversion adapter

Android smartphone

HDMI conversion cable or

Android smartphone

SiriusXM-

Connect

Vehicle Tuner terminal (sold separately)

Steering wheel remote control terminal (sold separately)

Microphone

Gray

Black

Black

Gray

Black

Purple

Red

Right

Left

Front audio output terminal

White

Red

Right

Left

Rear audio output terminal White

Red

White

Yellow

Right

Left

Subwoofer output terminal

(MONO 2ch) video output terminal

Yellow video input terminal

Red

Right audio input terminal

White

Left

External

Amplifier

Rear Monitor iPod/iPhone

Connection cable

(CCA-750)

NX604/FX503 61

Blue/White

Orange/White

Blue

Grass-Green

Purple/White

Yellow

+12V main power

Black

Purple

Rear right

Purple/Black

Rear right

Red

+12V accessory

Gray

Front right

Gray/Black

Ground

Front right

White

White/Black

Front left

Front left

Green

Green/Black

Rear left

Rear left

Amplifier turn-on lead

Illumination

Auto antenna

Parking brake lead

Reverse gear lead

See next page for how to connect the parking brake lead.

Connecting the parking brake lead

Connect the lead to parking brake lamp ground in the meter panel.

● Connecting the parking brake lead to lamp ground allows you to watch video images when the parking brake is engaged.

● When the parking brake lead is not connected, the monitor will not display video images.

● If “ Audio Only” appears on the screen just after turning on the ACC power of the car, release the parking brake while confirming safety, and then engage the parking brake again.

Parking brake lamp

+ lead to battery

Parking brake

● How to attach the electro-tap

1. Place the Parking brake lead at the stopper, and fold it back in the direction of the arrow.

2. Pass the Parking brake signal lead through, and fold it back in the direction of the arrow.

Electro-tap

(sold separately)

Parking brake signal lead

Parking brake signal lead

Parking brake signal lead

Parking brake lead

(Grass-Green)

Stopper

Parking brake lead

(Grass-Green)

❏

Connecting the Accessories

Connection to the Rear Vision Camera for vehicle

The Rear Vision Camera for vehicle can be connected to optional Rear Vision Camera input cable (CCA-644) with RCA pin cable. For detailed information, refer to the instruction sheet or manual for the Rear Vision Camera.

● Be sure to connect the reverse gear lead to the vehicle ’s relevant terminal.

● Connect the Rear Vision Camera to the RCA pin cable; if not, the screen turns black while the gearshift lever is in the reverse gear position.

SiriusXM-Connect Vehicle Tuner

Connect this tuner to SiriusXM-Connect Vehicle Tuner terminal.

For more information on how to install the SiriusXM Connect Vehicle tuner, consult the installation guide included with the tuner.

62 NX604/FX503