bollards - Barrier Group
SECTION
01
BOLLARDS
Products in this section are primarily used for traffic control, property protection
and ram-raid prevention. Our bollards are available in a wide range of styles
and materials to suit most applications. We have a product sure to satisfy
your requirements, whether it be surface mounted, in-ground, retractable or
removable bollards. Manufactured from heavy wall tube in either mild steel or
stainless steel, these products are built to take the knocks.
You may also be interested in pages:
23
BUMPA-BAR
25
SHOCK ABSORBING
GUARD RAILS
36
POST & RAIL
78
FLEXIBLE BOLLARDS
3
STAINLESS STEEL BOLLARDS
Our round stainless steel bollards are offered in three
designs: below ground for installation into a concrete
footing, core drilled for installation into a core drilled
hole using epoxy adhesive, or surface mount for bolted
installations.
Manufactured from marine grade 316 stainless steel these
bollards are all finished with No. 4 mechanical linish
before being electro-polished. This is recommended for
installation near coastal areas to minimise the risk of
tea staining and to ensure the bollards maintain a high
quality appearance over many years.
SECTION
01
A
D
C
All our stainless steel bollards have a fully welded
and polished cap. This helps present a high quality
appearance required for architectural environments.
For the ultimate high quality presentation, polished
stainless steel skirts are available as an option to cover
the base plates and fixings.
Value features:
E
GROUND
LEVEL
316 grade polished stainless steel.
Electro-polished for maximum protection.
Three methods of installation.
90 or 140mm diameter.
Optional cover skirts available.
F
B
ANCHORING
BARS
BELOW GROUND & SURFACE MOUNT MODELS
BELOW GROUND, SURFACE MOUNT & CORE DRILLED SPECIFICATIONS
Welded and polished flat cap.
PART NO.
C90BG-SS
C90CD-SS
C90SM-SS
COV90-SS
C140BG-SS
C140CD-SS
C140SM-SS
COV140-SS
Optional base cover.
A
B
C
D
E
F
(mm)
(mm)
(mm)
(mm)
(mm)
Stainless
Grade
Weight
(kg)
Cap
(mm)
3.05
3.05
3.05
–
–
6
–
–
225
316
316
316
3.40
3.40
3.40
–
–
10
–
–
300
316
316
316
8kgs
7.4kgs
7.4kgs
0.3kgs
25kgs
22kgs
19kgs
0.5kg
Welded Flat
Welded Flat
Welded Flat
N/A
Welded Flat
Welded Flat
Welded Flat
N/A
900
300
90
900
200
90
900
–
90
Optional 90mm base cover – stainless steel
1200
500
140
1200
200
140
1200
–
140
Optional 140mm base cover – stainless steel
Surface Finishes
L
EP
















Surface Finish: L – No.4 Linished. EP – Electro-polished.
BOLLARDS
Copyright © 2012 Barrier Group Pty. Ltd.
4
SECTION
01
ROUND BOLLARDS
Our fixed round, surface mount and below ground bollards
are designed for traffic control situations and asset
protection.
The surface mount bollards have fully welded base plates
and are suitable for installation onto any concrete surface.
The below ground bollards have fully welded starter bars
for installation into new concrete footings. Suitable for
installation in asphalt or any soft surface where a concrete
footing will be necessary.
C
C
A
All our bollards are supplied complete with necessary
fixings. They are manufactured from heavy wall mild
steel and hot dip galvanised as standard with the option
of powder coating as a final finish. (Safety yellow is our
standard colour. Other colours are available on request).
A
D
D
Optional chain rings are available for connecting chains
or ropes. Simply order with chain rings. Chain rings can
also be purchased separately for retro fitting to existing
bollards by drilling and tapping M10 threads as required.
E
Value features:
Cast aluminium caps provide high quality finish.
Standard class 1 reflective band.
Fully welded heavy steel base plate.
Welded starter bars for fixing into concrete footing.
All models hot dip galvanised as standard.
B
Polyethylene protective sleeves are available to suit round
90 and 140mm bollards. For more information see page 5.
ANCHORING
BARS
B
SURFACE MOUNT & BELOW GROUND MODELS
Cast aluminium caps.
Surface mount flange.
SURFACE MOUNT SPECIFICATIONS FOR ROUND BOLLARDS
PART NO.
C63SM
C63SM-G
C90SM
C90SM-G
C140SM
C140SM-G
C165SM
C165SM-G
C220SM
C220SM-G
A
B
C
D
E
Weight
(mm)
(mm)
(mm)
(mm)
(mm)
(kg)
900
900
900
900
1200
1200
1300
1300
1300
1300
150
150
225
225
300
300
350
350
400
400
63.5
63.5
90
90
140
140
165
165
220
220
1.6
1.6
5
5
5
5
5
5
6.4
6.4
6
6
6
6
10
10
12
12
12
12
4
4
9
9
23
23
34
34
45
45
No. of Fixings
3
3
4
4
4
4
4
4
4
4
Size of Fixing
(sleeve anchor)
Cap
10 x 50mm
10 x 50mm
12 x 60mm
12 x 60mm
16 x 65mm
16 x 65mm
20 x 75mm
20 x 75mm
20 x 105mm
20 x 105mm
Push in
Push in
Fixed
Fixed
Fixed
Fixed
Loose
Loose
Loose
Loose
Surface Finishes
G
P















Surface Finish: G – Galvanised. P – Powder coated safety yellow unless specified a custom colour.
BOLLARDS
Copyright © 2012 Barrier Group Pty. Ltd.
5
SECTION
01
Welded anchoring bars.
Optional chain rings (FIX1117).
BELOW GROUND SPECIFICATIONS FOR ROUND BOLLARDS
PART NO.
C63BG
C63BG-G
C90BG
C90BG-G
C140BG
C140BG-G
C165BG
C165BG-G
C220BG
C220BG-G
A
B
C
D
Weight
Size of Anchoring Bars
(kg)
Anchoring
Bars
(mm)
(mm)
(mm)
(mm)
900
900
900
900
1200
1200
1300
1300
1300
1300
300
300
380
380
500
500
650
650
650
650
63.5
63.5
90
90
140
140
165
165
220
220
1.6
1.6
5
5
5
5
5
5
6.4
6.4
4
4
12
12
29
29
40
40
53
53
2
2
2
2
2
2
2
2
2
2
30 x 30 x 50mm angle
30 x 30 x 50mm angle
30 x 30 x 50mm angle
30 x 30 x 100mm angle
30 x 30 x 100mm angle
30 x 30 x 100mm angle
30 x 30 x 100mm angle
30 x 30 x 100mm angle
30 x 30 x 100mm angle
30 x 30 x 100mm angle
Surface Finishes
Cap
Push in
Push in
Fixed
Fixed
Fixed
Fixed
Loose
Loose
Loose
Loose
G
P















Surface Finish: G – Galvanised. P – Powder coated safety yellow unless specified a custom colour.
BOLLARD PROTECTION SLEEVES
Barrier bollard protection sleeves offer a quick, simple
and economical way to recondition old rusted, faded
or scratched bollards without ever needing to remove,
replace or re-paint again.
Barrier’s modular bollard protection sleeves and caps
fit any standard 140mm or 90mm diameter bollards,
regardless of whether they are ours or a competitor’s.
Ideal for shopping centres, carparks, schools and
warehouses. Particularly useful in food processing
facilities where chipped or flaking paint and powder coat
surfaces are a health hazard.
They can be washed down and are not affected by most
chemicals or oils etc.
The 140mm diameter sleeve module is 300mm in length
and 225mm for the 90mm diameter model. The modules
can be grouped in single colours or alternating colours
for additional safety awareness. Eg. Yellow/Black or
Red/White. Our bollard sleeves and caps offer economical
long term indoor/outdoor protection and always look fresh.
The super tough polyethylene sleeve caps complete the
installation of our bollard protection sleeves. The cap is
secured in place which in turn prevents the sleeves from
being removed.
You won’t ever need to repair
scratched, rusted or faded bollards again!
BOLLARDS
Available for 90 and 140mm round bollards.
PART No.
PBS90-Y
DESCRIPTION
90mm Yellow sleeve module
PART No.
PBS140-Y
DESCRIPTION
140mm Yellow sleeve module
PBSC90-Y
90mm Yellow sleeve cap
PBSC140-Y
140mm Yellow sleeve cap
PBS90-B
90mm Black sleeve module
PBS140-B
140mm Black sleeve module
PBSC90-B
90mm Black sleeve cap
PBSC140-B
140mm Black sleeve cap
PBS90-R
90mm Red sleeve module
PBS140-R
140mm Red sleeve module
PBSC90-R
90mm Red sleeve cap
PBSC140-R
140mm Red sleeve cap
PBS90-W
90mm White sleeve module
PBS140-W
140mm White sleeve module
PBSC90-W
90mm White sleeve cap
PBSC140-W
140mm White sleeve cap
Copyright © 2012 Barrier Group Pty. Ltd.
6
SECTION
01
SQUARE BOLLARDS
Our fixed, square surface mount and below ground bollards
are designed for traffic control situations and asset
protection.
The surface mount bollards have fully welded base plates
and are suitable for installation onto any concrete surface.
C
The below ground bollards have fully welded starter bars
for installation into new concrete footings. Suitable for
installation in asphalt or any soft surface where a concrete
footing will be necessary.
C
A
All our bollards are supplied complete with necessary
fixings. They are manufactured from heavy wall mild
steel and hot dip galvanised as standard with the option
of powder coating as a final finish. (Safety yellow is our
standard colour. Other colours are available on request).
A
D
D
Optional chain rings are available for connecting chains
or ropes to our bollards. Simply order with chain rings.
Chain rings can also be purchased separately for retro
fitting to existing bollards by drilling and tapping M10
threads as required.
E
B
ANCHORING
BARS
Value features:
Available in two sizes.
Standard class 1 reflective band.
Fully welded heavy steel base plate.
Welded starter bars for fixing into concrete footing.
All models hot dip galvanised as standard.
B
SURFACE MOUNT & BELOW GROUND MODELS
SURFACE MOUNT SPECIFICATIONS FOR SQUARE BOLLARDS
PART NO.
A
B
C
D
E
Weight
(mm)
(mm)
(mm)
(mm)
(mm)
(kg)
No. of Fixings
CS90SM
900
200
90
5
6
12.75
4
CS90SM-G
900
200
90
5
6
12.75
4
CS150SM
1200
300
150
5
10
32
4
300
150
5
10
32
4
CS150SM-G 1200
FIX1117
Metric shoulder gold eye bolt – can be attached to any of the above when requested.
Surface Finishes
Size of Fixing
(sleeve anchor)
Cap
12 x 60mm
12 x 60mm
20 x 75mm
20 x 75mm
Welded Flat
Welded Flat
Welded Flat
Welded Flat
G
P





–

–
BELOW GROUND SPECIFICATIONS FOR SQUARE BOLLARDS
PART NO.
A
B
C
D
Weight
(mm)
(mm)
(mm)
(mm)
(kg)
Anchoring
Bars
CS90BG
900
400
90
5
16.5
2
CS90BG-G
900
400
90
5
16.5
2
CS150BG
1200
500
150
5
38
2
500
150
5
38
2
CS150BG-G 1200
Metric shoulder gold eye bolt – can be attached to any of the above when requested.
FIX1117
Size of Anchoring Bars
30 x 30 x 50mm angle
30 x 30 x 50mm angle
30 x 30 x 100mm angle
30 x 30 x 100mm angle
Surface Finishes
Cap
Welded Flat
Welded Flat
Welded Flat
Welded Flat
G
P





–

–
Surface Finish: G – Galvanised. P – Powder coated safety yellow unless specified a custom colour.
BOLLARDS
Copyright © 2012 Barrier Group Pty. Ltd.
7
SHOCK ABSORBING BOLLARDS
The Shock Absorbing Bollard (SAB) has the ability
to shift sideways if hit at or near ground level.
If the impact is higher up the bollard, it can tilt up to
8 degrees, at which point it locks up offering maximum
protection. Alternatively if the contact is of a deflection
or glancing nature, the SAB is able to rotate through
360 degrees.
Each SAB comes fitted with high impact polyethylene
protective sleeves. The sleeves are U.V. stabilised and
won’t fade, rot, rust or peel. Never have to paint chipped,
scratched or rusted bollards again. (For more information
on protective bollard sleeves see page 5).
SABs are designed to be used anywhere vehicles are
manoeuvring at low speeds, such as carparks and
warehouses etc. The self centering design means the
SABs can take repeated impacts without incurring
permanent damage. They simply absorb the impact and
return to their original position.
These unique characteristics result from the combination
of clever engineering and the use of high tech composite
materials. SABs are available in 140mm diameter in
either core drilled in-ground or surface mounted models.
Note: Not recommended for high speed traffic
environments.
SECTION
01
140mm
5mm Wall
Protective
Polyethylene
Sleeves
over hot dip
galvanised bollard
1200mm
Value features:
Eliminates damage caused by low speed impacts.
Moves in 3 directions simultaneously to absorb impact.
Suitable for indoor or outdoor use.
Ideal for carparks and warehouses etc.
Absorbs low speed impacts without sustaining damage.
Fitted with Yellow/Black protective polyethylene sleeves.
Absorbs the impact and returns to its original position.
Available in core drilled or surface mount models.
Polypropylene
Tim-rings
50mm
350mm
200mm
Specifications:
Description:
Shock Absorbing Bollard (SAB).
Material:
Mild steel and composite core structure.
Finish:
Height:
Yellow / Black high impact
polyethylene sleeves over galvanised
bollard.
1200mm above ground.
Diameter:
140mm (bollard).
Weight:
Approx. 33kgs.
Installation:
Core drilled – 50mm hole x 200mm deep.
Surface mount – 4 x M12 x 102mm
structural anchors (supplied).
This is what can happen to
rigidly fixed bollards with
even a low speed impact.
SABs simply absorb this
kind of impact.
PART No.
DESCRIPTION
SAB140-CD
Shock Absorbing Bollard – Core drilled 140mm dia.
SAB140-SM
Shock Absorbing Bollard – Surface mount 140mm dia.
BOLLARDS
SURFACE MOUNT & BELOW GROUND MODELS
Shock Absorbing Bollard (SAB140-CD shown)
360º
1
8º
2
20mm
3
DEFLECTION IMPACT
TYPICAL UPPER IMPACT
TYPICAL LOWER IMPACT
Ability to rotate
through 360º
Maximum angle of
deflection 8º
Maximum sideways
deflection 20mm at
ground level
The vast majority of damage caused to assets is by vehicles manoeuvring at
low speed. SABs have the ability to completely eliminate this damage.
Copyright © 2012 Barrier Group Pty. Ltd.
8
SECTION
01
FOLD DOWN BOLLARD
Fold Down Bollards have been designed for applications
such as vehicle access control.
In the lay flat position the bollard is only 80mm high
allowing sufficient vehicle clearance. In the upright
position it stands 800mm high with a broad face of
150mm wide. Comes complete with a reflective sign face
for greater visibility.
Supplied with a 40mm padlock also available as a key
lockable model which includes two keys.
The vehicle bollards are available as a surface mount
model or can be used with an in-ground kit (BGK4) for
setting into new concrete. For installation into asphalt
it is recommended to use a concrete footing for added
strength and stability.
It can be supplied in either hot dip galvanised or high
visibility safety yellow powder coat. Replacement or
additional sign face ordered separately.
Value features:
Stands 800mm tall when locked up.
Only 80mm high in the lay flat position.
Available in surface mount or used with concrete
footing kit.
Padlock lockable model includes fixings and padlock.
Key lockable model includes fixings and two keys.
Hot dip galvanised or finished in high visibility safety
yellow powder coat.
Broad 150mm face includes reflective sign face.
BGK4
The fold down bollard stands 800mm high in the upright position.
Specifications:
Description:
Fold down access barrier.
Material:
Mild steel.
Finish:
Safety yellow powder coat and galvanised
or galvanised only.
Height:
Down 80mm / Up 800mm.
Weight:
Operating 5kgs / Shipping 12kgs.
Fixing:
Surface mount supplied with 4 off
12 x 60mm. Masonry anchors.
Locking:
40mm padlock (supplied) or key lockable.
Sign:
Class 2 reflective sheeting
120 x 500mm (included).
For parking space protection
see our Lok-Up on page 70.
Only 80mm high in the lay flat position.
PART No.
DESCRIPTION
FD150
Powder coated fold down bollard – Padlock
FD150-G
Galvanised coated fold down bollard – Padlock
FD150K
Powder coated fold down bollard – Key lockable
FDS1
Reflective sign face with Red & Yellow diagonal stripes
BGK4
In-ground kit for FD150
BOLLARDS
FDS150K – Key lockable.
FDS150 – Padlock.
Copyright © 2012 Barrier Group Pty. Ltd.
Need Advice?
We can offer technical support over
the phone or maybe you simply need
a specification sheet.
CALL NOW!
Installation?
or just a site inspection…
Some things just can’t be conveyed over the phone.
In this case a site visit from one of our experienced
representatives or installers will help us better
understand your requirements, and allow us to
recommend an appropriate solution that satisfies
your needs.
CALL NOW!
Or...Something
Custom Made?
As designers and manufacturers with
many years of experience, we can produce
a new design or modify an existing
product to suit your unique requirements.
CALL NOW!
10
section
01
Cam-lok Removable BollardS
The Cam-lok range of removable bollards with their heavy steel
construction were originally designed to help combat ‘Ram-raids’ on
businesses. While they still serve this security role with thousands of
them now in the field, we find that our Cam-lok’s are being used more
and more in architectural environments for managing vehicle access in
restricted areas.
These are very expensive and make up a substantial part of the cost
of the finished bollard, which is why most competitors removable
bollards currently on the market use cheap, very poor quality locks that
are unreliable and readily breached. While this may reduce the initial
investment, it compromises the effectiveness of the bollard and the
long term security of your assets.
These architectural applications vary from the security role in that
there is a greater demand for an aesthetically pleasing design, hence
the use of polished stainless steel instead of the more industrial
powder coated finishes.
Another area where our product differs from most is that all our steel
bollards (including those with powder coated finishes) are hot dip
galvanised during manufacture. Alternatively our stainless steel models
are made from marine grade 316.
However some things never change, one of these is our insistence
on using only the very highest quality ‘Bi-lock’ removable core lock
mechanisms with security registered keying.
Cam-lok removable bollards come in two styles. Freestanding for shop
front or public open space installations, and roller door models for the
protection of factory roller shutter doors.
Cam-lok Specifications
POST
Part No.
BCL90
BCL90-G
BCL90-SS
BCL90RD
BCL90RD-G
BCL140
BCL140-G
BCL140-SS
(kgs)
cored
sleeve
Part No.
12.3
12.3
9.0
12.5
12.5
21
21
17
bcl90s-cd
bcl90s-cd
bcl90ss-cd
bcl90s-cd
bcl90s-cd
bcl140s-cd
bcl140s-cd
bcl140Ss-cd
POST
POST
A
B1
B2
C
Post
Description
Finish
(mm)
(mm)
(mm)
(mm)
90
90
90
90
90
140
140
140
950
950
950
950
950
1050
1050
1050
200
200
200
200
200
200
200
200
5.0
5.0
3.05
5.0
5.0
5.0
5.0
3.40
90mm freestanding post
Powder coated
90mm freestanding post
Galvanised
90mm freestanding post
316 stainless steel
90mm roller door post with door brackets
Powder coated
90mm roller door post with door brackets
Galvanised
140mm freestanding post
Powder coated
140mm freestanding post
Galvanised
140mm freestanding post
316 stainless steel
D2
(mm)
concrete
sleeve
Part No.
(mm)
225
225
225
225
225
225
225
225
bcl90s-nc
bcl90s-nc
bcl90ss-nc
bcl90s-nc
bcl90s-nc
bcl140s-nc
bcl140s-nc
bcl140Ss-nc
425
425
425
425
425
425
425
425
D1
Cam-lok accessories
Surface mounted bollard storage
Hanging post holders
Replacement locks and keys
These robust storage units offer a secure
location to place your Cam-lok bollards while
they are out of the ground. Because the
bollard locks into the holder in the same way
it does into the in-ground sleeve they are safe
to mount outside, where they are close to
where they are being used. They are a welded
steel design and plated to resist rusting,
available in two sizes to suit both 90 and
140mm bollards.
Hanging post holders are manufactured
from anodised aluminium. Because they
are not lockable they are best suited for
internal storage of idle Cam-lok bollards.
Each hanging holder is designed to hold one
bollard, and will accept either 90 or 140mm
models. They must be fixed into a sturdy
wall, alternatively they can be post mounted
if required.
Our premium ‘Bi-lock’ components have
a number of benefits. Because of the
removable core design, locks can quickly
be re-keyed or damaged cores replaced if
necessary without the need to dismantle the
bollard to access the lock body. As all keys
and locks are registered to the owner keys
can not be cut without authorisation.
PART No. DESCRIPTION
BCL90H
Cam-lok 90mm surface mount storage unit
PART No. DESCRIPTION
PART No. DESCRIPTION
BCL140H
Cam-lok 140mm surface mount storage unit
BHH
BCLKEY
BOLLARDS Wall mount bollard storage unit
Cam-lok additional registered key
Copyright © 2014 Barrier Group Pty. Ltd.
11
CAM-LOK FEATURES
SECTION
ROLLER DOOR
01
FREE STANDING
SECURITY
REGISTERED
KEY
SECURITY
REGISTERED
KEY
New caps & handles
New cast aluminium handles, caps and lock
shrouds finished in a silver grey metallic
powder coat add a refined architectural look
and improved grip to our removable bollards.
A
C
B1
Above Ground
6mm THICK
FLIP TOP
PEDESTRIAN
CAP
6mm THICK
FLIP TOP
PEDESTRIAN
CAP
Premium locking system
B2
Our Cam-lok bollards are fitted with
top quality ‘Bi-lock’ security locks with
quick change cores that can be removed
for maintenance or rekeying without
disassembling the bollard.
Below Ground
D1
D2
Either of these in-ground sleeves are available
for all removable bollards. Please specify core
drilled or new concrete when ordering.
NEW CONCRETE SLEEVES
CORE DRILLED SLEEVES
New concrete sleeves are used where there is
no existing concrete and a footing needs to
be poured. Such applications would include
gravel or bitumen surfaces or where the
bollards need to be installed into a garden
bed or grassed area. The sleeves are open
to the bottom to allow for drainage and
incorporate a hinged 6mm thick flush cap.
Where sleeves are to be installed into
existing concrete a hole 106mm in diameter
is core drilled into the slab, the sleeve is
then set into the hole using an appropriate
epoxy adhesive. The bollard interlocks with
the sleeve to form a burst proof connection.
When the bollard is removed the hole is
covered by a 6mm thick hinged flush cap.
BOLLARDS
Roller door brackets
These heavy duty roller door brackets
interlock with the bollard shackle to lock the
door down to the ground thereby offering
maximum security against ‘ram raiding’ or
levering up of the door.
Copyright © 2012 Barrier Group Pty. Ltd.
12
section
01
sleeve-lok Removable BollardS
The Sleeve-lok range of removable bollards with their heavy steel
construction are well suited to help combat “Ram-raids” on
businesses. They have served this security role now for over 12 years
with thousands having been installed in all manner of applications.
We find that our Sleeve-lok’s are also very widely used for managing
vehicle access in restricted areas. These include industrial sites, parks
and gardens and numerous other public space environments.
shop front or public open space installations, and roller door models
for the protection of factory roller shutter doors.
Sleeve-lok removable bollards are differentiated from the Cam-lok
range by their locking method. Where the Cam-lok’s use high security
locks with an internal locking mechanism, the Sleeve-lok’s use a
simple padlock design whereby the cap on the in-ground sleeve is
secured to a high strength steel shackle welded onto the bollard.
Another area of improvement and one where our entire bollard range
differs from our competitors, is that they are all hot dip galvanised
during manufacture. This includes bollards that are have a powder
coated finish. This is a significant development as hot dip galvanising
has a dramatic impact on reducing corrosion and increasing the
service life of the bollard.
In keeping with a greater demand for an aesthetically pleasing design
in street furniture and fixtures used in public open spaces, we have
undertaken a major re-design of our removable bollard range. This is
evident in the smart new cast aluminium caps and handles on the
Sleeve-lok bollards.
Sleeve-lok removable bollards come in two styles. Freestanding for
sleeve-lok Specifications
(kgs)
cored
sleeve
Part No.
4.5
4.5
12
12
12.2
12.2
21
21
bSl63s-cd
bSl63s-cd
bSl90s-cd
bSl90s-cd
bSl90s-cd
bSl90s-cd
bSl140s-cd
bSl140s-cd
POST
POST
POST
A
B1
B2
C
Post
Part No.
Description
Finish
(mm)
(mm)
(mm)
(mm)
BSL63
BSL63-G
BSL90
BSL90-G
BSL90RD
BSL90RD-G
BSL140
BSL140-G
63mm freestanding post
63mm freestanding post
90mm freestanding post
90mm freestanding post
90mm roller door post with door brackets
90mm roller door post with door brackets
140mm freestanding post
140mm freestanding post
Powder coated
Galvanised
Powder coated
Galvanised
Powder coated
Galvanised
Powder coated
Galvanised
63
63
90
90
90
90
140
140
900
900
950
950
950
950
1050
1050
150
150
200
200
200
200
200
200
1.6
1.6
5.0
5.0
5.0
5.0
5.0
5.0
D2
(mm)
concrete
sleeve
Part No.
(mm)
150
150
225
225
225
225
225
225
bSl63s-nc
bSl63s-nc
bSl90s-NC
bSl90s-NC
bSl90s-NC
bSl90s-NC
bSl140s-nc
bSl140s-nc
300
300
425
425
425
425
425
425
D1
sleeve-lok accessories
Surface mounted bollard storage
Hanging post holders
High security padlocks
These robust storage units offer a secure
location to place your Sleeve-lok bollards
while they are out of the ground. Because the
bollard locks into the holder in the same way
it does into the in-ground sleeve the holder
is safe to mount outside where it is close to
where it is being used. They are a welded
steel design and plated to resist rusting,
available in three sizes to suit 63, 90 and
140mm bollards.
Hanging post holders are manufactured from
an anodised aluminium extrusion. Because
they are not lockable they are best suited for
internal storage of idle Sleeve-lok bollards.
Each hanging holder is designed to hold one
bollard, and will accept either 90 or 140mm
bollards (Note: 63mm models are not suited
to hanging holders). Hanging holders must
be fixed into a sturdy wall or they can be post
mounted if required.
We sell and recommend the use of a high
quality padlock with a shielded shackle to
help prevent tampering. The BPL2 is a high
strength lock with a 9mm protected shackle.
It is chrome plated to resist corrosion and
is supplied with 2 keys per lock. Locks can
be supplied keyed alike if you have multiple
units or keyed differently.
PART No. DESCRIPTION
BSL63H
Sleeve-lok 63mm surface mount storage unit
BSL90H
Sleeve-lok 90mm surface mount storage unit
PART No. DESCRIPTION
PART No. DESCRIPTION
BSL140H
Sleeve-lok 140mm surface mount storage unit
BHH
BPL2
BOLLARDS Wall mount bollard storage unit
High security 9mm shielded padlock (2 keys)
Copyright © 2014 Barrier Group Pty. Ltd.
13
SLEEVE-LOK FEATURES
SECTION
ROLLER DOOR
01
FREE STANDING
25mm
REFLECTIVE
BAND
25mm
REFLECTIVE
BAND
New caps & handles
New cast aluminium handles and caps
finished in a silver grey metallic powder coat
add a refined architectural look and improved
grip to our removable bollards.
A
C
B1
Above Ground
6mm THICK
FLIP TOP
PEDESTRIAN
CAP
6mm THICK
FLIP TOP
PEDESTRIAN
CAP
Positive locking
Sleeve-lok bollards are secured into the
ground by padlocking the 6mm thick sleeve
cap to the 10mm thick welded shackle on the
bollard with our BPL2 high security padlock.
B2
Below Ground
D1
D2
Either of these in-ground sleeves are available
for all removable bollards. Please specify core
drilled or new concrete when ordering.
NEW CONCRETE SLEEVES
CORE DRILLED SLEEVES
New concrete sleeves are used where there is
no existing concrete and a footing needs to
be poured. Such applications would include
gravel or bitumen surfaces or where the
bollards need to be installed into a garden
bed or grassed area. The sleeves are open
to the bottom to allow for drainage and
incorporate a hinged 6mm thick flush cap.
Where sleeves are to be installed into
existing concrete a hole 106mm in diameter
is core drilled into the slab, the sleeve is
then set into the hole using an appropriate
epoxy adhesive. The bollard interlocks with
the sleeve to form a burst proof connection.
When the bollard is removed the hole is
covered by a 6mm thick hinged flush cap.
BOLLARDS
Roller door brackets
These heavy duty roller door brackets
interlock with the welded bollard shackle to
lock the door down to the ground, thereby
offering maximum security against ‘ram
raiding’ or levering up of the door.
Copyright © 2012 Barrier Group Pty. Ltd.
14
SECTION
01
SURFACE MOUNT
REMOVABLE BOLLARDS
Surface mount removable bollards are designed
for applications where the floor cannot be core drilled
or penetrated. For example, spaces with suspended,
prestressed slabs or clean areas such as food preparation or
pharmaceutical processing.
They are available in two different models, the Cam-lok
model and the Tee-lok model. Structurally both models are
identical but offer different locking systems depending on
the level of security required.
Cam-lok model
This heavy duty bollard locks into the surface mounted
receiver shoe via an internal locking system which utilises
a high security cam lock with registered keys.
(2 keys are supplied per order. Additional keys may be
purchased if required).
Tee-lok model
The surface mount Tee-lok is exactly the same as the
surface mount Cam-lok except that it does not employ
high security locking. Instead, the Tee-lok uses our unique
‘T’ handle key to unlock and remove the bollard from the
receiver shoe.
Tee-lok is ideally suited to low or medium security
applications, where the aim is to stop vehicles entering
unauthorised areas or separating vehicles from
pedestrians, especially around work places.
Value features:
Strong 90mm post with 5mm thick wall.
Heavy steel receiver shoe only 20mm high
when post removed.
Requires only 4 off 12mm holes, 65mm deep.
No core drilling or slab penetration.
Internal locking system with either high
security cam-loks with registered keys
or unique ‘T’ handle keys.
Fixings for receiver shoe are inaccessible
when post locked in.
Optional colours available on request.
Tee-lok model shown.
Specifications:
Description:
Surface mount removable bollards.
Material:
Steel post 90mm diameter with 5mm wall.
Finish:
Zinc plated and E-Coated prior to safety
yellow powder coat.
Height:
950mm post height.
Receiver shoe only 20mm high with post
removed.
Weight:
Post 11.9kgs / Receiver shoe 2.9kgs.
Installation:
4 off 12 x 65mm sleeve anchors.
PART No.
DESCRIPTION
SMCL
Cam-lok surface mount bollard
BCLKEY
Additional Cam-lok registered key
SMTL
Tee-lok surface mount bollard
BRKEY
Additional ‘T’-handle key for Tee-lok
SMCLH
Receiver shoes for Cam-lok / Tee-lok
(Also used as a storage unit for bollards)
BOLLARDS
Bollard installed into shoe.
Bollard to shoe interlock (SMCLH).
Cam-lok model (SMCL).
Tee-lok model (SMTL).
Copyright © 2012 Barrier Group Pty. Ltd.
Retractable bollards are designed for medium security
applications such as traffic and parking control. They offer
a simple, trouble free operation proven over many years of
installation.
Note: A retractable bollard should not be used where
high security locking is required, such as car yards etc.
For these applications insurance companies insist on
our “Cam-lok” removable bollards.
The retractable bollard is now available with a choice of
two different materials. The BR900 has a 5mm thick
mild steel bollard that is zinc coated and E-Coated before
being powder coated in hi-vis safety yellow with two
reflective bands. The BR900-SS has a 3.05mm thick
316 marine grade stainless steel bollard. As this model is
designed for more architectural applications it does not
include reflective bands.
15
Black
anti-slip surface
RETRACTABLE BOLLARDS
– Powder Coated or Stainless Steel
SECTION
01
50mm Class 1
Reflective Band
(2 places)
BR900 Steel
model only
90mm
900mm
Now available with the
option of a 316 marine grade
stainless steel bollard
(without reflective bands)
Powder coat
E-Coat
Zinc
Value features:
Locks in both up and down positions.
Strong circular design 90mm diameter x 5mm wall.
Black anti-slip surface on top of bollard.
Unique low cost ‘T’ handle key.
Convenient, no loose posts to store.
Galvanised in ground casing.
Available with a powder coated finish or 316 grade
stainless steel bollards.
Trouble free design. Only 2 moving parts.
Internal locking system can’t be tampered with or
fouled by dirt or water.
Note: 2 keys supplied per order. Additional keys may
be purchased.
Concrete
footing
Galvanised
in-ground
casing
Compacted fill
1150mm
Specifications
Description:
Material:
Finish:
Height:
Weight:
Locking:
Installation:
Retractable bollard for vehicle access
and parking control.
Bollards 90mm diameter with 5mm mild
steel or 3.05mm 316 stainless steel wall.
In ground casing 140mm with 5mm wall
mild steel.
Powder coated models are zinc plated prior
to E-Coating and finally powder coated.
Stainless steel models are marine grade 316.
In-ground casings for all models are hot
dip galvanised.
Drainage
aggregate
Above ground 900mm.
Below ground 1150mm.
BR900 41.5kgs / Operating weight 6kgs.
BR900-SS 38kgs / Operating weight 4kgs.
Unique internal locking mechanism
with ‘T’ handle key.
Excavation and concrete footing.
350mm
Diameter
E-COATING is another name for electrocoating, electropainting, or
electrophoretic lacquering. It is used to deposit a paint or lacquer
coating (rather than metal, as is deposited by electroplating).
PART No.
DESCRIPTION
BR900
Retractable bollard assembly – powder coated
BR900R
Replacement bollard
BR900-SS
Retractable bollard assembly – 316 stainless steel
BR900R-SS
Replacement 316 stainless steel bollard
BRKEY
Additional ‘T’ handle key for retractable bollard
BOLLARDS
1. Locks in down position.
2. Turn to unlock and lift.
3. Turn to lock in up position.
Copyright © 2012 Barrier Group Pty. Ltd.
16
IP03
RETRACTABLE BOLLARDS
SECTION
01
Installation Procedure:
1. Set out and bore holes approximately
500mm diameter. Recommended
spacing for bollards is 1400mm
maximum, centre to centre. Holes
should be 100mm deeper than the
length of the galvanised ground
casing. (PHOTO 1).
2. Place coarse gravel in the bottom
of the hole, sit the bollard on this
base until the top flange plate is
approximately 10mm above the
natural ground level. Ensure bollard
is plumb then place more gravel
around the bollard until the hole is
approximately 1/3 full. (PHOTO 2).
1.
2.
3.
4.
5.
6.
3. Replace some of the excavated
soil from the hole and compact until
the hole is approximately 2/3 full.
Check the operation of the bollard.
(PHOTO 3).
4. When satisfied the bollard is plumb
and at the correct height, cover the
top with tape to prevent entry of
cement into bollard casing. Fill the
balance of the hole with 35-50 mpa
concrete. Add steel reinforcing if
required. (PHOTO 4).
5. Finish off concrete as desired,
remove the protective tape and clean
around the bollard and top flange.
(PHOTO 5).
6. Stand back and admire your
beautiful work. Well done! (PHOTO 6).
PLEASE NOTE
a. When finishing off the concrete, taper the surface
slightly away from the surface flange. This will
reduce the amount of water that finds its way into
the ground casing.
b. The coarse gravel in the bottom of the hole acts
as a drainage sump for water that finds its way
into the casing. This is normal and should not be
seen as a problem.
c. Never allow the bollard to free-fall from the raised
position. Always lower using the ‘T’ handle key.
Photos courtesy of R.L. Reed Inc. (Las Vegas).
BOLLARDS
Copyright © 2012 Barrier Group Pty. Ltd.
IP04
17
RETRACTABLE BOLLARDS
SECTION
01
Locking Procedure:
1. Insert the ‘fingers only’ of the key
into the bollard, as shown.
Note: Slot in bollard is off-centre.
Insert key so that handle is facing
out on ‘short’ side of the cap.
1. Insert key to short side.
2. Fully insert and pivot key
to upright position.
3. Rotate to unlock then lift.
4. Lift until fully extended.
5. Rotate to lock.
6. Confirm bollard is locked.
(DIAGRAM 1).
2. Fully insert key while pivoting
upwards into the vertical position.
Note: It is important that the key is
fully inserted until it can not go any
further. (DIAGRAM 2).
3. Lift the key until the weight of
the bollard is taken.
Rotate anti-clockwise to unlock.
(DIAGRAM 3).
4. Lift bollard until fully extended.
(DIAGRAM 4).
5. While holding bollard in the fully
extended position, rotate in
anti-clockwise direction until it
stops. Remove the key. The bollard
should now be locked in the upright
position. (DIAGRAM 5).
6. Now re-insert the ‘fingers only’ of the
key and support the bollards weight,
then twist from left to right. If locked
correctly there will be minimal
rotation. If not locked, the bollard
will fully rotate and retract.
(DIAGRAM 6).
Note: Reverse procedure to unlock and
lower bollard.
WARNING
NEVER ALLOW
THE BOLLARD
TO FREE FALL
INTO THE GROUND.
DAMAGE MAY RESULT.
BOLLARDS
Copyright © 2012 Barrier Group Pty. Ltd.
ATTENTION Architects, Specifiers and Buyers!
Recycling. Is it really good for the environment, or just a load of old rubbish?
It has long been my opinion that specifiers and buyers of wheel stops and speed humps manufactured from recycled
rubber naively accept without question, that recycling of old tyres and other scrap rubber into new products is good for the
environment.
To answer the above question, Barrier Group has engaged Dr Enda Crossin and his team from the Centre for Design at
RMIT University in Melbourne, to undertake a comparison Life Cycle Assessment (LCA) study of the cradle to grave
environmental impacts including end of life disposal scenarios for our new LLDPE Compliance wheel stops and those
made from recycled rubber.
As part of our product development and marketing activities, Barrier Group are interested in investigating the environmental
impacts of the Compliance one piece wheel stop system, and how these impacts compare with those of similar wheel stop
systems, produced from recycled rubber. This study will provide insights into the comparative environmental properties of
the two wheel stop systems which will support Barrier Group in identifying key areas for product improvement and innovation.
Goal & scope
The primary aim of the study is to quantify and compare the life cycle environmental impacts, including those related to
manufacture, distribution, use and disposal, of the following wheel stop systems:
1. Compliance one piece wheel stop, produced from injection-moulded linear low-density polyethylene (LLDPE)
by Barrier Group Pty. Ltd.
2. Recycled rubber wheel stop, produced from reclaimed tyres and scrap rubber of unknown origins by various
manufacturers.
In order to assess the life cycle impacts of the two wheel stop systems six key indicators will be applied to the study,
they are described in the table below.
Table 2-1: Impact assessment indicators to be applied
Indicators
Unit
Description
Global Warming
kg CO2 eq
Climate change effects resulting from the emission of carbon dioxide (CO2), methane and other greenhouse gases into the
atmosphere. Factors applied to convert emissions of greenhouse gas emissions into carbon dioxide (CO2) equivalents emissions
conform to IPCC 2007 factors for a 100 year time horizon.
Water use
kL H2O
Water usage. Total of all water used by the processes considered.
Solid waste
kg
Solid waste generated. Total of all solid waste generated by the processes considered. This indicator has been designed according
to the first CML impact assessment method (CML 92 V2.04). Note that the CML 92 is the only European impact assessment
method that takes solid waste into account. CML is a research centre based in the Institute of Environmental Sciences of Leiden
(Netherlands).
Photo-oxidation
formation
C2H4-eq
Photochemical Ozone Creation Potential (POCP) (also known as summer smog) for emission of substances to air is calculated with
the UNECE Trajectory model (including fate), and expressed in kg ethylene equivalents/kg emission
Human toxicity
DALY
Total damage caused by non-carcinogenic and carcinogenic emissions measured in disability adjusted life years (DALY), a rate of
mortality and disability, which ranks years of life lost with years of disease and disability.
Depletion of minerals
& fossil fuels
MJ Surplus
The additional energy required to extract resources (both mineral and fossil) due to depletion of reserves, leaving lower quality
reserves behind.
The minerals indicator has been designed from an Eco-Indicator impact assessment method (Eco-indicator 1999 (H) V2.05).
Eco-Indicator is an impact assessment method developed by Product Ecology Consultants, a Dutch based research and consultancy
company. The method has been developed between 1997 and 1999, commissioned by the Dutch Ministry of Urban Planning,
Housing and the Environment.
The terms of engagement for this study were outlined with RMIT in November 2011 and the study commenced in April 2012.
It is anticipated the study will be completed in August of 2012 at which time the results will be published on our websites
and be available for downloading. They will also be distributed on request in hard copy.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement