Multi-Format Broadcast

Monitor

BEM-182, 212, 242

User’s Guide

Contents

Introduction.................................................................................................................................3

Features.......................................................................................................................................3

Safety Instructions.......................................................................................................................4

Front............................................................................................................................................5

Tally.............................................................................................................................................7

Rear.............................................................................................................................................7

OSD Menu.......................................................................................................................................9

VIDEO........................................................................................................................................9

DISPLAY 1...............................................................................................................................11

DISPLAY 2...............................................................................................................................13

COLOR.....................................................................................................................................15

MARKER..................................................................................................................................16

OSD 1........................................................................................................................................17

OSD 2........................................................................................................................................19

AUDIO......................................................................................................................................20

GPI............................................................................................................................................22

SYSTEM...................................................................................................................................23

Monitor Control via Serial Port................................................................................................24

USB Firmware Update..............................................................................................................24

External Remote Control..........................................................................................................25

List of Compatible Video Formats (HDMI)..............................................................................26

List of Compatible Video Formats (SDI)..................................................................................27

Specifications............................................................................................................................29

Dimensions................................................................................................................................35

Troubleshooting........................................................................................................................36

Warranty Information................................................................................................................38

Modification of Product............................................................................................................38

Caution on Menu Operation......................................................................................................38

Caution for Monitor Placement.................................................................................................38

Caution for Usage.....................................................................................................................38

2

Features

Firmware Update with USB Memory

Focus Assistance/False Color (SDI)

Waveform/Vectorscope (SDI)

Closed Caption (CEA-608/708) (SDI)

Time Code (SDI)

8~16ch Audio Level Meter

Video Exposure Range Check (SDI)

UMD Mode (SDI)

AFD & V-CHIP (SDI)

Various Markers

H/V Delay (SDI)

Tally LED Control Output R/G/B/W Internal Patterns Rack & VESA Mount (Option)

3G SDI input (Level A/B)

1~16Ch Audio Level Meters

3

Safety Instructions

• To help avoid damaging your monitor, connect only one power (AC or DC) in operation.

• Rough handling of product may cause physical damage or malfunction.

• Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock.

• To avoid electric shock, never touch the inside of the monitor. Only a qualified should open the monitor’s case.

• Openings in the monitor cabinet are provided for ventilation. To prevent overheating, these openings should not be blocked or covered.

• Put your monitor in a location with low humidity and a minimum of dust. Avoid places like damp basement or dusty hallways.

• Place the monitor on a solid surface and treat it carefully. The screen is made of glass and can be damaged if dropped or sharply hit.

• Do not attempt to remove the back cover, as you will be exposed to a shock hazard. The back cover should only be removed by qualified service personnel.

• Unplug the monitor power before you connect external devices to the monitor.

• If your monitor does not operate normally, or if there are any unusual sounds or smells coning from it, unplug it immediately and contact us.

• Please do not disassemble the monitor. No service will be provided in that case.

• Displaying fixed picture for a long time may cause an afterimage or dead spots. To recover LCD pixels, display whole white picture on screen for a n hour or two and pixels will be recovered.

• No service will be provided for user’s own color calibration.

4

Front

①

②

③

④

⑤

⑥

⑦

⑧

⑨

⑩

⑪

1) Power (Standby) Button

2) Input

HDMI / SDI Input Selection.

3) Marker On/Off

4) Scan

Switches scan mode.

5) R/G/B/Gray

Switches to display Red, Green, Blue or Gray color only.

6) H/V Delay

Displays ancillary data.

7) WF/VS (SDI)

Displays waveform, vectorscope.

* Some afterimage might be left on Waveform when the input picture freezed long on interlace signal.

5

* On SDI 2K input with Psf scanning mode, displaying Circle or

Horizontal Line pattern might cause an afterimage effect. However, it will be disappeared after the picture is changed.

8) Function Keys

User-preferred function can be assigned to function keys. Assignable functions are listed below.

● ALM (Audio Level Meter) Display On/Off

● Freeze Frame On/Off

● UMD Display

● Front Button LED On/Off

● Video Loss Display On/Off

● Focus Assist

● False Color

● Exposure Range Check

● Audio Mute

● 1:1 Scan On/Off

● Caption Display

● Time Code

9) Menu

Displays Menu.

10) Adjust Knob

Works as arrow keys or selector.

11) Phone Jack

Headphone Output.

6

Tally

Tally mode displays Red, Green, Amber color by the input from tally (RJ-45 GPI) input port.

Rear

1) SDI IN

2) SDI OUT

SDI Loop-through out.

3) HDMI IN

4) USB

USB Port for firmware update.

5) SERIAL 1

Serial port for firmware update and monitor control.

7

6) SERIAL 2

Serial port for firmware update and monitor control.

7) REMOTE

Ethernet port for monitor control.

8

OSD Menu

Menu opens up by pressing Menu button. This button also works as Exit button on the Menu. The brightness knob works as up/down arrow. To select something, press either enter button or the knob.

* The menu may disappear on no signal or unstable signal input.

* Menu setting is saved for each input mode. So the user should make selection on an appropriate input mode.

VIDEO

Brightness

Adjust brightness.

Contrast

Adjust contrast.

Chroma (Hue)

Adjust chroma.

Phase

Adjust phase.

Sharpness

Adjust sharpness. Default: 12s.

SDI 3G Mode

Set this mode if the input is 3G HD SDI. SDI 3G mode support SMPTE standards listed below:

▶ A_MS1_YCbCr422_10

: 3G SDI Level-A Mapping Structure 1 – YCbCr 4:2:2/10 bit

▶ A_MS2_YCbCr444_10

9

: 3G SDI Level-A Mapping Structure 2 – YCbCr 4:4:4/10 bit

▶ A_MS2_RGB444_10

: 3G SDI Level-A Mapping Structure 2 – RGB 4:4:4/10 bit

▶ A_MS3_YCbCr444_12

: 3G SDI Level-A Mapping Structure 3 – YCbCr 4:4:4/12 bit

▶ A_MS3_RGB444_12

: 3G SDI Level-A Mapping Structure 3 – RGB 4:4:4/12 bit

▶ A_MS4_YCbCr422_12

: 3G SDI Level-A Mapping Structure 4 – YCbCr 4:2:2/12 bit

▶ B_MS1_YCbCr422_10

: 3G SDI Level-B Mapping Structure 1 – YCbCr 4:2:2/10 bit

▶ B_MS2_YCbCr444_10

: 3G SDI Level-B Mapping Structure 2 – YCbCr 4:4:4/10 bit

▶ B_MS2_RGB444_10

: 3G SDI Level-B Mapping Structure 2 – RGB 4:4:4/10 bit

▶ B_MS3_YCbCr444_12

: 3G SDI Level-B Mapping Structure 3 – YCbCr 4:4:4/12 bit

▶ B_MS3_RGB444_12

: 3G SDI Level-B Mapping Structure 3 – RGB 4:4:4/12 bit

▶ B_MS4_YCbCr422_12

: 3G SDI Level-B Mapping Structure 4 – YCbCr 4:2:2/12 bit

▶ B_2X_DS1_YCbCr422_10

: 3G SDI Level-B Data Stream 1 – YCbCr 4:2:2/10 bit, Dual Link SMPTE-372M

▶ B_2X_DS2_YCbCr422_10

: 3G SDI Level-B Data Stream 2 – YCbCr 4:2:2/10 bit, Dual Link SMPTE-372M

Especially for 3G Level B signals, the format should be set manually.

Also, be aware that the format information might be lost on power down.

10

DISPLAY 1

Aspect

Set the aspect ratio of the screen. 16:9, 4:3, Native(Original) are selectable.

1:1 Scan

Set this on to display picture in 1:1 pixel mapping.

Anarmorphic

Set this mode to resize the screen to 3.56:1, 2.74:1, 2.59:1, 2.55:1, 2.40:1, 2.39:1, 2.35:1, 1.85:1,

1.75:1, 1.66:1, or 1.37:1.

Waveform Display

Select waveform display mode. Choose Normal to analyze whole screen, choose Line Select to analyze a specific line of the screen.

Waveform Line Select

Select the line when you select Line Select mode for Waveform display.

Waveform Color Mode

Choose either Single or Mixed.

Waveform Intensity

Set waveform color’s intensity between 0~63.

WFM & Vector Size

Set Waveform and Vectorscope size among three kinds.

WFM & Vector Blend

Set transparency of Waveform and Vectorscope window between 0~6.

11

Timecode Display

Set this mode on to display timecode from SDI signal. Select the appropriate timecode that you wish to display among LTC (Longitudinal Time Code), VITC (Vertical Interval Time Code),

DVITC (Digital Vertical Interval Time Code).

Timecode Position

Set Top or Bottom position for timecode.

12

DISPLAY 2

Exposure Range Check (Video Range Check)

Checks Y, C level and displays over-exposed or under-exposed area on screen. The base value can be Y, Cb, or Cr.

Y Range Max / Min

Set Y range value for range check.

C Range Max / Min

Set C range value for range check.

Blink Color

The filled area color by range check can be either Black, Blue, Green or Red.

Blink Time

Set blinking time of the area between 1 to 5 seconds.

Focus Assist

Turns on Focus Assist mode. This mode can be set also by pressing Focus Assist button in front.

Focus Assist Level (Sensitivity)

The sensitivity of the focus assist function can be set between 0 to 48.

Focus Assist Color

Set brush color of focus assist mode among Blue, Green, and Red.

False Color

Shows pictures in specific colors as its luminance level other than the original colors. Much exposed area is filled with red while little exposed area is purple.

13

* 10-bit, 12-bit Dithered gradient pattern might not be displayed clearly in this mode.

14

COLOR

Dithering

Set this mode on to display gradient more smoothly.

Color Temperature

VAR, 3200K, 5400K, 6500K, 9300K color temperatures are preset and selectable by user. On User mode, user can adjust RGB gain and bias. Adjusting on User mode is recommended to professional users.

15

MARKER

Marker Ratio

Select one of preset markers or user marker. To display marker, press Marker button in front of the monitor.

Center Marker

Set preference to display center marker or not.

Safety Area 16:9

Adjust size of the safety area when marker displayed on 16:9 screen.

Safety Area 4:3

Adjust size of the safety area when marker displayed on 4:3 screen.

Marker Color

Select marker’s color among White, Red, Green, Blue, Gray and Black.

Marker Mat

Set how to display outside of the safety area. Normal, Half(Gray), Black are selectable.

Marker Thickness

Set marker thickness between 1 to 10.

User Marker H1 / User Marker H2 / User Marker V1 / User Marker V2

Set user marker’s position. H1 for left, H2 for right, V1 for top, V2 for bottom. The positions are saved as the selected marker name such as USER1.

16

OSD 1

OSD Display Time

Set OSD menu display time. Choose 0 for infinite.

OSD Blend

Set transparency of the menu between 0 to 5.

OSD(Menu) Position

Set menu position among Left Top, Right Top, Left Bottom, Right Bottom and Center.

V-Chip

SD-SDI, Composite signal might contain V-Chip data. Turn this mode on to display V-Chip information on screen.

Closed Caption

Select one of 608 Line 21, 608 VANC, 608 Transcoded, 708 to display Closed Captions. In special condition such as menu display status, captions are not displayed.

CC708 Service

Select one of CC service as your preference.

Service 1: general captions.

Service 2: translated captions.

Service 3,4: not assigned.

CC608 StartLine

Display line of captions are selectable by user. (e.g. 13)

17

Internal Pattern

To test monitor display without signal, turn this mode on. Several patterns such as Color Bars, Blue,

Green, Red, White and Black are selectable.

UMD Display

Set this mode on to display UMD text on screen.

UMD Color

Select UMD text color among Red, Green, and Amber.

UMD Edit

Set the UMD source ID to display on screen.

18

OSD 2

PIP Source

Selects the main picture source for Picture-in-Picture mode. The sub-picture source is automatically selected to the other input. (e.g. If HDMI is set as main, SDI is automatically set as sub-picture)

PIP Mode

Adjusts mode of the sub-picture among Small, Large, or Side by Side.

PIP Position

Selects position of the sub-picture.

19

AUDIO

Audio Level Meter

Turns on/off audio level meters.

Level Meter SDI Channel

Set the audio channels to display.

Level Meter Type

Select one of two types: pair or group.

Level Meter Direction

Select one of two orientations : Horizontal or Vertical.

Level Meter Size

Select the size of the meters : Small or Large.

Level Meter Position

Select the position of the meters : Upper or Lower.

Peak Hold Decay Time

Set the decay time of the meters.

3G Level B Audio

Select one audio signals when there are two inputs.

Embedded Audio Left

Select audio channel for left (Ch 1 ~ 15)

20

Embedded Audio Right

Select audio channel for right (Ch 2 ~ 16)

Audio Source

Select audio source for speaker among Auto / SDI / HDMI.

When both SDI, HDMI cables are connected, It is able to listen to SDI audio on HDMI video input by this menu. However, It is not able to listen to HDMI audio on SDI video input.

21

GPI

GPI Control

Turns on/off external monitor control function.

GPI Port 1,2,3,4,5,6

Assigns each GPI port’s function. (e.g. SDI 1 input, HDMI input, Tally Red) See EXTERNAL

REMOTE CONTROLLING section for details.

Remote ID Number

Assigns the ID for the monitor to control through serial port. 0 to 99 can be assigned.

Serial Remote

Turns serial remote function on. All front buttons are locked on this mode. To exit from this mode, press and hold Menu button for 3 seconds.

22

SYSTEM

Function 1,2

Assigns a function to each function button.

Backlight

Set the backlight intensity from 0 to 40. An LCD panel requires more than 30 minutes to be settled to a new backlight value.

Front Button LED

Set front LEDs on/off status.

Font Button Lock

Locks front buttons not to work. Press and hold Menu button for 3 seconds to exit from this mode.

Update Firmware

Turns update mode on. Select Serial or USB port for update. After firmware update, the monitor should be turned off/turned on, and Factory Default should be loaded before use.

Setup Load

Load monitor settings from Factory Default, User 1/2/3/4.

Setup Save

Save current monitor setting to use later. 4 settings can be saved.

Firmware Version

This version number is required when you request for service.

Operating Time

This indicates total hours that the monitor operated.

23

Monitor Control via Serial Port

This is optional feature of the monitor.

User can control multiple monitors via serial port on the back. Connect PC and monitor with RS-

422 (general telephone cable), using an appropriate gender. (e.g. a RS-232C to RS-422 gender, or a

USB to RS-232C to RS-422 gender)

In most cases this kind of gender is needed because PC does not have phone port, but RS-232C port or USB.

PC Software BWS-100 will be provided as request.

PC

(Wall System Controller)

BWS-100

Adaptor (RS-232C to RS-422 Converter)

USB Firmware Update

To update your monitor's firmware, request for a new firmware file to your local reseller or to BON

Electronics.

Move the file on a USB flash memory, insert it to your monitor. Please beware the file should be located in the root(top folder level).

Also, the USB flash memory should have FAT32 or FAT file system. (USB memory has FAT32 file system, usually)

Set Update Firmware item as USB from SYSTEM menu.

Some part of firmware cannot be updated by USB updating procedure, so please get help from your local dealer or expert before you update firmware with USB memory.

Error Message when USB access or file not exist

Message when file on USB detected

You can also use Serial Port and your PC to update the firmware. Please request for help to your local dealer or directly to BON Electronics.

24

External Remote Control

Connecting GPI Port(RJ-45)

Turning the monitor off is recommended before cable connection. Assignable functions are listed below.

Function Name

SDI-1 Input

SDI-2 Input

HDMI Input

YPbPr Input

CVBS-1 Input

CVBS-2 Input

CVBS-3 Input

KEY-UP ▲

KEY-DOWN ▼

KEY- MENU

KEY-ENTER

Aspect

1:1 Scan On/Off

H/V Delay On/Off

TC Display On/Off

ALM Display On/Off

Freeze On/Off

Front Button LED On/Off

Tally Red On/Off

Tally Green On/Off

Description

Switches the input to SDI-1

Switches the input to SDI-2

Switches the input to HDMI

Switches the input to YPbPr

Switches the input to CVBS-1

Switches the input to CVBS-2

Switches the input to CVBS-3

CURSOR UP on Menu Control.

CURSOR DOWN on Menu Control.

Menu On/Off

Enter Button

Aspect On/Off

1:1 SCAN Function On/Off

H/V Delay Function On/Off

TC Display On/Off

Audio Level Meters Display On/Off

Freeze Frame On/Off

Front Button LED On/Off.

Tally Red LED On/Off

Tally Green LED On/Off

Backlight

Set the backlight intensity from 0 to 40. An LCD panel requires more than 30 minutes to be settled to a new backlight value.

Front Button LED

Set front LEDs on/off status.

25

List of Compatible Video Formats (HDMI)

NO

Signal Input

Formats

NTSC

PAL

720*576/50i

720*480/59.94i

720*480/60i

720*576/50p

720*480/59.94p

720*480/60p

1280*720/23.98p

1280*720/24p

1280*720/25p

1280*720/29.97p

1280*720/30p

1280*720/50p

1280*720/59.94p

1280*720/60p

1920*1080/50i

1920*1080/59.94i

1920*1080/60i

1920*1080/23.98p

1920*1080/24p

1920*1080/25p

1920*1080/29.97p

1920*1080/30p

1920*1080/50p

1920*1080/59.94p

1920*1080/60p

18

19

20

21

14

15

16

17

22

23

24

25

26

10

11

12

13

8

9

7

6

3

4

1

2

5

6

INPUT

HDMI

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

26

List of Compatible Video Formats (SDI)

NO

Input Signal

Formats

1 NTSC

2 PAL

3 525/60i (SD)

4 625/50i (SD)

5 720*480/59.94p

6 720*576/50p

7 1280*720/23.98p

9 1280*720/24p

9 1280*720/50p

10 1280*720/59.94p

11 1280*720/60p

12 1920*1035/59.94i

13 1920*1035/60i

14 1920*1080/50i

15 1920*1080/59.94i

16 1920*1080/60i

17 1920*1080/23.98p

18 1920*1080/23.98psf

19 1920*1080/24p

20 1920*1080/24psf

21 1920*1080/25p

22 1920*1080/25psf

23 1920*1080/29.97p

24 1920*1080/29.97psf

25 1920*1080/30p

26 1920*1080/30psf

27 1920*1080/50p

28 1920*1080/59.94p

29 1920*1080/60p

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

√

√

√

-

-

-

-

-

-

√

√

√

√

√

√

√

√

-

√

√

√

√

√

√

√

-

-

-

-

-

√

√

√

-

-

-

-

√

√

√

√

√

√

√

√

-

√

√

√

√

√

√

√

-

-

-

-

-

√

√

√

√

√

√

√

√

√

√

√

-

√

√

√

-

-

-

-

√

√

√

√

√

√

√

√

√

√

√

Single

HD/SD-SDI

3G

YUV4:2:2

3G

YUV4:4:4

-

3G

RGB444

-

-

-

27

30 2048*1080/23.98p

31

36

2048*1080/23.98psf

32

35

2048*1080/24p

33 2048*1080/24psf

34 2048*1080/25p

2048*1080/25psf

2048*1080/29.97p

37 2048*1080/30p -

-

√

√

√

√

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

√

√

√

√

√

√

√

√

28

Specifications

BEM-182

LCD

Size

18.5"

Resolution

1366 x 768

0.3 x 0.3mm

Pixel Pitch

Color

16.7M(8bit) Colors

Viewing Angle(deg)

170(H), 160(V)

Luminance of White

Contrast

250 cd/m²

1000 : 1

Back Light

LED

Display Area (H x V)

Input

409.8 x 230.4 mm (16.1 x 9.0 inches)

1 x BNC

HD/SD-SDI, 3G/1.485G/270M

1 x HDMI

Output

HDMI1.3 (with HDCP v.1.3), 19pin Female

1 x BNC

Input Signal Format

SDI Loop Through

SMPTE 425M AB

Level A MS1, MS2, MS3, MS4

Level B MS1, MS2, MS3, MS4

2048*1080,24p/psf,23.98p/psf

2K, SMPTE 428M

SMPTE 274M/292M

1920*1080i (60, 59.94, 50)

1920*1080p (30, 29.97, 25, 24, 24sF, 23.98, 23.98sF)

SMPTE 296M

1280*720p/60,59.94,50

29

SMPTE 260M

SMPTE 125M/259M

1920*1035i/60,59.94

720*480i/60,59.94, 720*576i/50

576i(50)

ITU R-BT.656

Audio

1 x Phone Jack Out

General

Headphone Out(Stereo)

1 x RJ-45

GPI-7 Port for control

2 x RJ-11

RS-422, RJ-11P Jack

1x USB

Dimensions(WxHxD)

For firmware update

Power Requirements

Weight

DC 12V/24V

Power Consumption

Operating Humidity

21W

Operating Temperature

0°C ~ 40°C

20% ~ 80% RH

5.0 kg / 10.0 lbs

Main Body : 459.0x264.0x38.3 mm / 18.0x10.3x1.5 inches

Accessories

• Power Cable • AC-Adapter • Manual • Cleaner

Options

• Rack Mount kit • Sun Hood •Screen Proctector •Wall Bracket •

Tilting Stand

• Carrying Case • V-Battery Mount • Anton Bauer Battery Mount

BEM-212

LCD

Size

Resolution

Pixel Pitch

21.5"

1920 x 1080

0.24825mm

30

Color

Viewing Angle(deg)

Luminance of White

Contrast

Back Light

16.7M(8bit) Colors

178(H), 178(V)

250 cd/m²

3000 : 1

LED

476.64 x 268.11 mm (18.7 x 10.6 inches)

Display Area (H x V)

Input

1 x BNC

HD/SD-SDI, 3G/1.485G/270M

HDMI1.3 (with HDCP v.1.3), 19pin Female

1 x HDMI

Output

1 x BNC

Input Signal Format

SDI Loop Through

SMPTE 425M AB

2K, SMPTE 428M

SMPTE 274M/292M

Level A MS1, MS2, MS3, MS4

Level B MS1, MS2, MS3, MS4

2048*1080,24p/psf,23.98p/psf

1920*1080i (60, 59.94, 50)

1920*1080p (30, 29.97, 25, 24, 24sF, 23.98, 23.98sF)

SMPTE 296M

SMPTE 260M

SMPTE 125M/259M

ITU R-BT.656

Audio

1280*720p/60,59.94,50

1920*1035i/60,59.94

720*480i/60,59.94, 720*576i/50

576i(50)

Headphone Out(Stereo)

1 x Phone Jack Out

General

1 x RJ-45

2 x RJ-11

GPI-7 Port for control

RS-422, RJ-11P Jack

31

1x USB

For firmware update

Power Requirements

DC 12V/24V

Power Consumption

39W

Operating Temperature

0°C ~ 40°C

Operating Humidity

20% ~ 80% RH

Weight

6kg / 13.2lbs

Dimensions(WxHxD)

Main Body : 523 x 299 x 38 mm / 20.5 x 11.7 x 1.5 inches

Accessories

• Power Cable • AC-Adapter • Manual • Cleaner

Options

• Rack Mount kit • Sun Hood •Screen Proctector •Wall Bracket •

Tilting Stand

• Carrying Case • V-Battery Mount • Anton Bauer Battery Mount

BEM-242

LCD

Size

Resolution

Pixel Pitch

Color

Viewing Angle(deg)

Luminance of White

Contrast

Back Light

Display Area (H x V)

Input

1 x BNC

24"

1920 x 1080

0.27675mm

16.7M(8bit) Colors

178(H), 178(V)

250 cd/m²

3000 : 1

LED

531.36 x 298.89mm (20.9 x 11.8 inches)

HD/SD-SDI, 3G/1.485G/270M

32

1 x HDMI

Output

SMPTE 425M AB

HDMI1.3 (with HDCP v.1.3), 19pin Female

1 x BNC

Input Signal Format

SDI Loop Through

Level A MS1, MS2, MS3, MS4

Level B MS1, MS2, MS3, MS4

2K, SMPTE 428M

2048*1080,24p/psf,23.98p/psf

SMPTE 274M/292M

1920*1080i (60, 59.94, 50)

1920*1080p (30, 29.97, 25, 24, 24sF, 23.98, 23.98sF)

SMPTE 296M

SMPTE 260M

SMPTE 125M/259M

1280*720p/60,59.94,50

1920*1035i/60,59.94

720*480i/60,59.94, 720*576i/50

576i(50)

ITU R-BT.656

Audio

1 x Phone Jack Out Headphone Out(Stereo)

General

1 x RJ-45

GPI-7 Port for control

2 x RJ-11

RS-422, RJ-11P Jack

1x USB

For firmware update

Power Requirements

DC 12V/24V

Power Consumption

40W

Operating Temperature

0°C ~ 40°C

Operating Humidity

20% ~ 80% RH

Weight

6.8 kg / 15.0 lbs

Dimensions(WxHxD)

Main Body : 583.6x330.6x38.1 mm / 22.8x12.9x1.5 inches

33

Accessories

Options

• Power Cable • AC-Adapter • Manual • Cleaner

• Rack Mount kit • Sun Hood •Screen Proctector •Wall Bracket •

Tilting Stand

• Carrying Case • V-Battery Mount • Anton Bauer Battery Mount

This specifications are subject to change without prior notice for product improvement.

34

Dimensions

MODEL

BEM-182

Unit mm inches

W H

459.0

264.0

18.0

10.3

D

38.3

1.5

Remark without Stand

MODEL

BEM-212

Unit mm inches

W

523

20.5

H

299

11.7

D

38

1.5

Remark without Stand

MODEL

BEM-242

Unit mm inches

W

583

22.8

H

330

12.9

D

38

1.5

Remark without Stand

35

Troubleshooting

Try these if you have trouble in using the monitor. Call for Service if you can't solve the problem even after you tried these solutions.

Symptom Solution

Power isn't turned on

Check Connectivity of Power Cable between Outlet and the Monitor.

Press and Hold Power button for more than one second.

Try with Other Monitor or Electric Device using the same Power Cable.

Check if battery voltage is above 12V when the monitor powered by battery.

Screen is Black and All Button Lights are

On in startup process

Reconnect the Power and Restart the Monitor.

(Call for Service if the Symptom appeared more than 3 times)

Screen is Black on Startup and there's neither BON Logo nor "No Signal"

Display, but Buttons are Working

Reconnect the Power and Restart the Monitor.

(Call for Service if the Symptom appeared more than 3 times)

There's a delay in BON Logo Display on

Startup

It is normal and No Reaction Required.

BON Logo appeared on Startup, but No

Screen Output when Input Signal

Connected

Remove Input Cable and Check if "No Signal" appears on Screen.

- restart the Monitor if you can't see "No Signal"

- Make Monitor "Factory Default" and Try again and Try again

- Check the Cable Connectivity

- Try with Different Cable

- Check the Input Format and Frequency

- Try with Different Input Device. If successful, the Failed Input Device may

Generate Non-Standard Signal (Please Inform Us its Model Name).

"No Signal" appears on the Screen

Check the Input Selection.

Make Monitor "Factory Default" and Try again.

Try with Different Input Cable.

Check the Cable Connection.

Check if the Input Format and Frequency is Supported.

Try with Different Input Device. If successful, the Failed Input Device may

Generate Non-Standard Signal (Please Inform Us its Model Name).

36

Strange Color on BON Logo on Startup

Reconnect the Power and Restart the Monitor.

(Call for Service if the Symptom appeared more than 3 times)

Make Monitor "Factory Default" and Try again.

the Startup Logo Color was ok but Strange

Color on Active Screen

Select Test Pattern(Internal Pattern) in the menu and See if R,G,B Color is

Correct.

Check the Input Selection.

Try with Different Cable.

Check if Each Cable is correctly Connected when you use Component as Input.

Screen Position Mismatch

Make Monitor "Factory Default" and Try again.

Reconnect the Power and Restart the Monitor.

Try with Different Input Device. If successful, the Failed Input Device may

Generate Non-Standard Signal (Please Inform Us its Model Name).

No Audio Output

Colors look different between different models

Check if the Volume level is 0.

Display the Audio Level Meters and See its output.

Give your Monitor 1 hour warmup time.

Because Different Panels have different Characteristics, Colors might look

Different.

Colors look different between same models

Give your Monitor 1 hour warmup time.

Same Panels are not exactly same but they have a tolerance range among them by the Panel Manufacturer, so Colors might look Different.

* The tolerance range is in Panel Standard Document included in CD

37

Warranty Information

Free Service

If the product needs to be repaired in 12 months from the purchase.

Exceptions

• damage caused by accident, abuse, misuse, water, flood, fire, or other acts of nature or external causes

• damage caused by service performed by anyone who is not an authorized service provider

• damage to a product that has been modified or altered without the written permission of BON

Service to be Charged

If the product needs to be repaired after 1 year and before 4 years from the purchase.

Modification of Product

Dimensions, specifications or design of the product are subject to change without prior notice for product improvement.

Caution on Menu Operation

OSD Menu might be freezed or broken on very high-quality or complicated pictures input. In that case, turn off the power for 5 seconds and turn it on to make Menu works.

Caution for Monitor Placement

For long lifetime and proper operation of the monitor, all surface of the monitor should not be blocked by any material for ventilation.

Caution for Usage

This monitor is designed to be used for broadcasting purpose. Using it as PC monitor is not recommended.

38

Corporate Headquarters

Tresebelle-Sky 2F, 1479 Gayang-2, Gangseo-gu, Seoul, South Korea

Research / Service Center

Vision Tower 7F, 1481 Gayang-2, Gangseo-gu, Seoul, South Korea

Telephone

+82 2 2659 0333

FAX

+82 2 2659 8133

Web http://www.bon.co.kr

Email [email protected]

39