SIPROMAC 650A vacuum packaging machine OWNER’S MANUAL

OWNER’S MANUAL

MANUEL DE L’UTILISATEUR

VACCUM MACHINE

650A

1

2

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your machine.

Failure to comply with these instructions may result in personal injury.

General Operation

• Read, understand, and follow all instructions in the manual and on the machine before starting. Keep this manual in a safe place for further and regular reference and for ordering replacement parts.

• Only allow responsible individuals familiar with the instructions to operate the machine. Be sure to know controls and how to stop the machine quickly.

• Never put your hands near moving parts.

• Only allow qualified individuals for the maintenance of your machine.

• Remove all obstacles, which may interfere with the machine functions.

• Clear the work area such as electrical wires, buckets, knives etc.

• Be sure that everyone else is clear of your work area before operating the machine.

• Do not sit nor stand on the machine.

• Always turn off the machine after your work is done. Never leave a running machine unattended.

• Always disconnect and wait till the machine has cooled before attempting any maintenance.

• Do not wear loose fitting clothes or jewelry as they may get caught in moving parts of the machine.

• Always wear security shoes, to prevent injury caused by moving the machine or objects falling from the machine.

• Never exceed the time limit to seal, which is recommended by the manufacturer. This is to avoid any damage that may be caused to the sealing bars and to eliminate the risk of fire in the machine. Thus avoiding corporal burns.

• Never touch the sealing bars after they have been used, this will avoid corporal burns. Wait a few minutes to let the machine cool down before touching.

• Always make sure that the sealing bars are well installed in their "Guide Blocks" before starting a cycle.

• Never incline the machine more than 30 degrees, it may tip over and hurt someone seriously.

• Work only in daylight or good artificial light.

Do not operate the machine while under the influence of alcohol or drugs!

3

Service

• Use proper containers when draining the oil. Do not use food or beverage containers that may mislead someone into drinking from them. Properly dispose of the containers, or store in a safe place immediately following the draining of the oil.

• Prior to disposal, determine the proper method to dispose of waste from your local office of

Environmental Protection Agency. Recycling centers are established to properly dispose of materials in an environmentally safe fashion.

Do not pour oil or other fluids into the ground, down a drain or into a body of water

.

Warning-Your responsibility

:

This machine should only be operated by personal who can read, understand and respect warnings and instructions regarding this machine in the owners manual. Save these instructions for future reference.

4

IV

VACUUM PACKAGING MACHINE

MODEL 650A

(MC-40 SIPROMAC)

GENERAL TABLE OF CONTENTS

I OPERATION INSTRUCTIONS

III

II MECHANICAL

A- Front view general assembly drawing

B- Rear view general assembly drawing

C- Cover adjustment procedure

D- Central shaft assembly drawing

E- Seal bar assembly drawings

(twin seal)

F- Seal bar assembly drawings

(electrical bag cut option)

G- Seal bar assembly drawings

(top and bottom sealing option)

H- Gas injection kit installation drawing

(gas injection option)

ELECTRICAL

A- Electrical drawings

PNEUMATIC

A- Pneumatic drawing

5

VACUUM PACKAGING MACHINES

OPERATION INSTRUCTIONS

TABLE OF CONTENTS

1. Setting up the machine

2. Electrical connection

3. Operation

3.1 Working principles

3.2 Special packaging

3.2.1 Gas flushing

3.2.2 Top and bottom sealing (bi-active)

3.2.2 3.2.3 Electrical bag cut

3.3 Setting of digital controls

3.4 Daily cleaning

4. Trouble shooting

4.1 Failure during a packaging cycle

4.2 Insufficient vacuum

4.2.1 Leakage in the bag

4.2.2 No leakage in the bag

4.2.3 Insufficient vacuum in the chamber

4.3 Faulty seal

4.3.1 Insufficient seal

4.3.2 No seal

4.3.3 Permanent sealing current

4.3.4 Seal does not stick

4.4 Fault in the valves

4.5 Control board failure

5. Regular maintenance

2010-08-30

6

SIPROMAC INC.

VACUUM PACKAGING MACHINES

1. SETTING UP THE MACHINE:

Before choosing the site for the machine, please consider that you will also need room for packaged and non-packaged products apart from the space needed for the machine itself.

Keep in mind that the machine must not be set up upon uneven ground. Especially with mobile models, the weight of the pump might then cause warping of the machine. Then the lid will not fit correctly.

Before starting to work, check the oil view glass on the pump, if there is a sufficient quantity of oil in the pump. Never use oil other than recommanded by the producer.

Never exceed maximum quantity of oil indicated, when adding or changing oil. Verify weekly.

Normal ambient temperature for the vacuum pump is between 10 to 70 temperature below 10 o o

C.For

C; it is recommended to use synthetic oil. Please consult factory and pump manufacturer manual for more information or when ambient temperature are outside normal limits

2. ELECTRICAL CONNECTION:

Electrical connections must be made by qualified personnel. This person must make sure that the electrical entries corresponds to the proper voltage and amperage of the machine. GROUNDING INSTRUCTIONS: This appliance must be connected to a grounded, metal, permanent wiring system; or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. A qualified electrician should be consulted if there is any doubt as to whether an outlet box is properly grounded.

All vacuum machines are supplied with an electrical schematic drawing.

An important step in connecting the machine is to make sure that the pump turns in its correct rotation.

The pump should not rotate more than 3 to 4 seconds in the wrong rotation or it may cause serious damage. The proper rotation is indicated by an arrow on the

pump motor.

3. OPERATION:

3.1 Working principles:

A vacuum packaging cycle is made of 3 stages. First the vacuum is made, the air is completly taken out of the chamber and from bag containing the product. (See figure 1).

Then it is possible to inject neutral gas from the nozzles, if the product is delicate.

Finally, a mechanism pushes the sealing bar to the rubber support to seal the bag.

7

To obtain nice packages, the products and the bags have to be of proportional sizes. The bag's opening should never exceed 50 cm(2") past the seal bars. The product should be centered in height in relation to the seal bar by adjusting the spacers provided.

To obtain a good seal, make sure that no residue of fat is left between the bag's inner sides where sealing is done.

3.2 Special packaging:

3.2.1 Gas flushing (option):

There is an atmospheric pressure of 1 kg/ sq. cm (14 lbs/sq. inch) upon products when fully evacuated. Products which can be damaged by high pressure must be packaged with a partial vacuum, or the pressure must be counterbalance by inflating the bag with gas (nitrogen or carbon dioxide) before sealing after evacuation.

For gas flushing, the bags are placed on the sealing bars, the open end placed over the gas nozzles mounted alongside the sealing bar. After evacuation, the vacuum valve closes and the gas valve opens. Gas time (sec.) can be set in the program menu.

The necessary gas tank and pressure valve mounted on tank is not supplied, The pressure of the gas regulator should be set at approximately 1/3 kg/sq. cm

( 5 lbs/sq.inch.). Each machine has an adaptor for gas connection when gas flush option is ordered.

3.2.2 Top and bottom sealing (optional):

When sealing aluminium laminate bags (especially bags for e.g. coffee) it is imperative to have an upper and a lower sealing bar.

3.2.2 Electrical bag cut (optional):

This option is used to obtain a package that the excess bagtail is cut off close to the seal (cannot be used with top and bottom sealing).

8

3.3 Vacuum packaging operation:

3.3 Vacuum packaging operation:

Note: Refer to the menus structure on page 14 and the keyboard detail on page 15.

3.3.1 Basics:

Use key "POWER" to power ON / OFF the vacuum packaging machine. When the unit is energized, the identification of the last executed program is displayed on LCD screen.

Use the "ESC" key to change over from the programs menu to the functions menu and from the functions menu to the programs menu.

In functions menu, use key "SELECT" to select a function and key "ENTER" to accede and executed the selection.

In programs menu, use key "SELECT" to select a program and key "ENTER" to accede and modify the selection.

In programs submenu, use key "ENTER" to pass over the parameters and point to the following one; the parameters are blinking to point out the acquisition mode. A return to programs menu is performed automatically following the last parameter acquisition.

In program submenu, use key "ESC" to get back to the programs menu.Strike any key to clear the error messages which may be displayed on LCD screen.

3.3.2 Functions:

3.3.2.1 Create a program:

When executing the "create a program" function, the program submenu is acceded, starting with the identification. The initial identification "Pxx NO NAME" is given to the program and all parameters are established to zero; the program number is allocated automatically.

3.3.2.2 Delete a program:

When executing the "delete a program" function, the programs menu is acceded and the number of the first program in memory is blinking to point out the deletion mode. Use key "SELECT" to select a program and key "ENTER" to accede and confirm deletion of the selection. Use key "ESC" to unconfirm a deletion and to leave the function. When leaving the function, the number of the actual program on LCD screen cease to blink.

3.3.2.3 Select operating mode:

When executing the "select operating mode" function, which is available only for the automatic units, the actual selection is blinking to point out the acquisition mode. Use key "SELECT" to get through the operating modes, which are automatic, semi-automatic and manual; the validation of the selected operating mode is performed automatically. Use key "ESC" or "ENTER" to leave the function and get back to the program menu.

9

3.3.3 Programs menu:

3.3.3.1 Program identification:

For a selected program, set the identification, using the numeric keyboard characters chart; press numeric key untill the desired character is selected

(4 times for the numeric value). Use key "ENTER" to validate the character and to validate the characters string at the end(the new characters string is blinking).

In a middle of an acquisition, use key "ESC" to come backward and erase one or several characters.

Example: EXAMPLE 1

 keys 2, 2, ENTER

 E

(9 characters) keys 8, 8, 8, ENTER

 X keys 1, ENTER

 A keys 5, ENTER

 M keys 6, ENTER

 P keys 4, 4, 4, ENTER

 L keys 2, 2, ENTER

 E keys 9, 9, 9, ENTER

 space keys 1, 1, 1, 1, ENTER

 1 key ENTER to validate the characters string

3.3.3.2 Vacuum level setting:

For a selected program set the vacuum level, starting with the values; the decimal point is automatically inserted following the second digit entry and the validation is automatically performed following the third digit entry (the new vacuum level is blinking). The vacuum level is rounded off to the nearest half value. In the middle of an acquisition, use key "ENTER" to validate the vacuum level and key "ESC" to come backward and start over with a new acquisition

(the old vacuum level is blinking). Set vacuum level to zero to bypass the pressure transducer and proceed only using the vacuum plus time.

Examples: 90.0%

 keys 9, 0, 0 or 9, 0, ENTER or keys 9, 0, 1 or 9, 0, 2 or 9, 0, 3 or 9, 0, 4

97.5%

 keys 9, 7, 5 or keys 9, 7, 6 or 9, 0, 7 or 9, 0, 8 or 9, 0, 9

0.0%

 keys 0, 0, 0 or 0, ENTER

3.3.3.3 Vacuum plus time setting:

For a selected program set the vacuum plus time, in seconds; the validation is automatically performed following the second digit entry (the new vacuum plus time is blinking). In a middle of an acquisition, use key "ENTER" to validate the vacuum plus time and key "ESC" to come backward and start over with a new acquisition (the old vacuum plus time is blinking).

Examples: 1s

 keys 0, 1 or 1, ENTER

10

15s

 keys 1, 5

11

3.3.3.4 Gas flush level setting:

For a selected program set the gas flush level following the same procedure as for the vacuum level; the maximum gas flush level setting is 10% below the vacuum setting.

3.3.3.5 Sealing time setting:

For a selected program set the sealing time, starting with the seconds; the decimal point is automatically inserted following the first digit entry and the validation is automatically performed following the third digit entry (the new sealing time is blinking). The sealing time is truncated to the nearest half hundredth. In a middle of an acquisition, use key "ENTER" to validate the sealing time and key "ESC" to come backward and start over with a new acquisition

(the old sealing time is blinking).

Examples: 4.50s

 keys 4, 5, 0 or 4, 5, ENTER or keys 4, 5, 1 or 4, 5, 2 or 4, 5, 3 or 4, 5, 4

2.35s

 keys 2, 3, 5 or keys 2, 3, 6 or 2, 3, 7 or 2, 3, 8 or 2, 3, 9

0.00s

 keys 0, 0, 0 or 0, ENTER

3.3.4 Vacuum cycle execution:

For the manual units and the automatic units set on manual, close the cover to initiate a vacuum cycle. For the automatic units set on semi-automatic or on automatic, use push button "STOP / START" to initiate or interrupt a vacuum cycle. A selected program can be initiated only in the programs menu, when no modifications are in progress, and the access to the other programs and functions is denied. During cycle execution the operation status is sequencally displayed on LCD screen, except for the parameters established to zero, which are not displayed:

- chamber vacuum level during vacuum sequence,

- vacuum plus time status during vacuum plus sequence,

- chamber vacuum level during gas flush sequence,

- sealing time status during sealing sequence,

- chamber vacuum level during atmosphere sequence.7

During cycle execution, use key "1" to abort the vacuum sequence and execute the following sequence, which is gas flush or sealing, and key "ENTER" to accede and modify the program; the parameters become valid only for the following vacuum cycles.

3.3.5 System monitor:

To accede the diagnostics menu, power up the vacuum packaging machine while keeping pushed in the "ESC"key. Use key "SELECT" to select the system monitor function and key "ENTER" to accede and visualize the monitored parameters. Use key

"SELECT" to change over from the software revision, the amount of working hours done and the amount of complete cycles performed since first initialization.

12

-MENUS STRUCTURE-

• Functions menu:

"F1 CREATE A PRGM"

"F2 DELETE A PRGM"

"F3 SELECT OPMODE" (automatic units only)

• Programs menu:

"Pxx NAME"

Program submenu:

"VACUUM: xx.x%" (10.0% - 99.5%)

"VACUUM PLUS: xxs"(0s - 99s)

"GAS FLUSH: xx.x%" (0.0% - 10% below the vacuum level) (units with gas option)

"SEAL TIME: x.xxs" (0.00s - maximum unit allocated setting)

"Pxx NAME" (12 characters)

• Diagnostics menu (keys "ESC" & "POWER" for access):

"DIAGNOSTICS MENU" (access code required)

"D1 INPUTS TEST"

"D2 OUTPUTS TEST"

"D3 MODEL SELECT"

"D4 GAS OPTION"

"D5 SEALING TIME"

"D6 COOLING TIME"

"D7 OFFSET CALIB.”

"D8 VACUUM SENSOR”

"D9 SIPROMAC PUB”

"D10 LOADING TIME" (automatic units only)

"D11 UNLOADNG TIME" (automatic units only)

"SYSTEM MONITOR" (no access code required)

"SOFTWARE: R x.xx"

"WORK HRS: xxxxx"

"CYCLES: xxxxxxx"

13

-KEYBOARD DETAILS-

MC-40 CONTROLS

14

WARNING: All electrical work described in this brochure should be done by

a QUALIFIED and AUTHORIZED technician.

3.4 Daily cleaning:

For hygenic cleanliness, it is imperative to clean chamber and spacers daily. Also clean the lid rubber to assure tight seat of the lid.

Cleaning instructions for gas injection nozzles: Periodically on a regular basis the gas injection nozzles must be removed with the connection tube and soaked in a food grade soap and water solution, then dried and re-installed.

4. TROUBLE SHOOTING:

4.1 Failure during packaging cycle:

4.1.1 "VACUUM ERROR" message is displayed on LCD:

No pressure variation is picked up by the PCB transducer during the vacuum sequence within a preset period of time.

- Check vacuum lines for potential leaks or kinks.

4.1.2 "GAS FLUSH ERROR" message is displayed on LCD:

No pressure variation is picked up by the PCB transducer duringthe gas flush sequence within a preset period of time.

- Check gas flush and vacuum lines for potential leaks or kinks.

4.1.3 "ATMOSPHERE ERROR" message is displayed on LCD:

No pressure variation is picked up by the PCB transducer during the atmosphere sequence within a preset period of time.

- Check vacuum lines for potential leaks or kinks.

4.1.4 "COVER DOWN ERROR" message is displayed on LCD(manual units):

The input signal of the down position switch has been lost during cycle execution.

- Check limit switch adjustment.

15

4.2 Insufficient vacuum:

4.2.1 Leakage in the bag:

Most frequently, insufficient vacuum in bags is due to leakage in bag and not due to any fault of the machine.

Pin-hole leak for which there is no obvious explanation is due to faulty bag material.

Pin-hole leak caused by sharp edge of the product (bone, etc.).Use bone-guard or thicker film.

Tear in bag by careless handling (sharp edge on filling table, damage made by retailer or customer).

Leakage in lateral or bottom seal, complain to supplier of bags or film.

4.2.2 No leakage in the bag:

Bag is too large, therefore the surplus of air remains visible (there is surplus of air in

0.4% of the bag volume in each bag). Use bags of suitable size.

Vacuum level is too low:

Pressure bar is jammed and closes opening of bag during evacuation.

4.2.3 Insufficient vacuum in chamber:

If troubles described under 4.2.1 and 4.2.2 do not apply, there is something wrong with the evacuation.To find the leakage quickly, check for leaks with a precision vacuumeter, going back step by step from the chamber to the pump.

At the chamber (measuring point at base of valve) at maximum time of evacuation. If more than 6 torr, proceed directly to the pump, if more than 3 torr:have pump service by pump supplier.If pressure at pump is good, reconnect hoses to pump and measure again.

Verify at vacuum hose connections and valve connections.

When proceeding this way, starting from pump, loss of pressure per step must not exceed 0.5 to 1 torr.

Caution:Verify connections of measuring equipment before verifing machine.

Most frequent points of leakage: lid gasket, damaged vacuum hose or loose hose clamps.

16

4.3 Faulty seal:

4.3.1 Insufficient seal:

Damaged teflon or silicone rubber.

Sealing pressure too low, bellows leaking or pressure bar jammed.

Leakers in seal: heating wire mechanically damaged (knicked) or silicone rubber uneven.

4.3.2 No seal:

Sealing wire burnt.

Faulty contact in sealing circuit.

Sealing transformer burnt through.

Contactor does not work.

4.3.3 Permanent sealing current:

Contactor is jammed check sealing transformer for damage through overload.

4.3.4 Seal does not stick:

Insufficient layer of polyethylene (inferior quality of bags).

Seal area extremely contaminated by fat or meat juice. Use filling aid.

Sealing temperature is too low (when using very thick films).

Caution: Do not increase sealing time more than really necessary; higher temperature will reduce working life of teflon and silicone rubber.

4.4 Fault in the valve:

Vacuum or air valve does not open.

Check whether there is voltage on the magnetic valves during their period of operation. If there is no voltage a wire is broken or the PC board is damaged.

Lid does not open at the end of the cycle; air enters, but there is still 20 - 40% vacuum in chamber. Vacuum valve does not close.

17

4.5 MC40 Control board failure

NOTE:Refer to menu structure on page 13.

This board software is allowing access to a "Diagnostics Menu". Only qualified service technicians are authorized to access this menu by entering a security password.

By acceding either the "D1 input test" feature or the "D2 output test" feature,a trained technician will be able to quickly know the origin of the problem: pump, sealing system, pneumatic problem, security switches problem, etc...

Keep in mind that in most cases trouble is due to a leakage, loose electrical connection or evident dammage to the main components: vacuum pump, valves, electrical contactors, thermal overload, fuses holder or transformer.

For assistance do not hesitate to contact your local service technicians.

5. Regular maintenance:

Routine controls to be made at regular intervals:

Check teflon for wear.

Check silicone rubber for burnt spots and smooth even position.

Check pressure bar for jamming.

Check lid sealing for damage and hardened spots.

Check switch-point of micro switch, adjust if necessary.

Check evacuation hose for damage (contraction of diameter, or abrasions).

Check vacuum connections for tightness.

Check oil in pump (oil level in view glass; add if necessary. Regular change of oil - necessity indicated by change of color).

Check vacuum in chamber with precision vacuumeter.

Check function of cycle with various settings of timers.

18

MODEL 650A

COVER ADJUSTMENT PROCEDURE

Reference Drawing:# 005-0325

# 004-0122

PROBLEM: MACHINE TABLE AND COVER SEEMS TO BE STRAIGHT, LID GASKET IS GOOD

BUT COVER DOES NOT SIT PROPERLY ON BOTH SIDES OF TABLE.

1. Floor should be flat (within 1/8" approx.).

2.1 Mark position of original adjustment of guide arm length and its lower shaft position (See drawing # 005-0416; items: #39 & #16).

2.2 Loosen the two bolts on the guide arm (See drawing # 005-0325; items #39).

2.3 Now move the cover each side and check how cover sits on the table. Distance between table and lid gasket should be under 1/16" approx. If so, go to step 3.0 for guide arm adjustment. Otherwise go to step 2.4 for central arm adjustment.

2.4 Put chamber in upright position and check with a square angle to see if arms are parallel. If not, loosen bolt at the end of one arm and adjust until square (See drawing # 005-0416; items #33, #14 & #44).

2.5 When closing cover (guide arm still loose), if cover is not sitting properly on either the front or rear of the table, you have to change the height of a central pillow block (See drawing #

004-0122; item #3) until cover is sealing properly each side (less than 1/16").

3. Adjustment of guide arm: two things have to be adjusted, the length and the lower axis position.

Each of these should be adjusted separately. Fix the lower axis in a central position, then adjust guide arm length by marking its position. When chamber is at the left and at the right, tighten at the center of your marks. Adjustment can be done a couple of times until everything is ok.

19

MECHANICAL DRAWING

20

7

3

LET.

MODIFICATION DATE INT.

2

A

5

1

005C0352

ITEM PART # DESCRIPTION

004A0213 COVER HANDLE ASS'Y

11

12

13

8

9

10

5

6

7

2

3

4

004A4239 LEFT REAR ACCESS DOOR PRE-ASSY

005-0349 FILLER PLATE ASSEMBLY

005-0359 ARM SUPPORT ASSEMBLY

005A1518 TABLE ASSEMBLY W/ARM

005A1519 RIGHT REAR ACCESS DOOR ASSY

005C0465 STRUCTURE ASSEMBLY

008-0368 ARM SUPPORT SPACER

051-0360 BOLT 3/8"-16nc. X 1" S/S

051-0622 NUT 3/8"-16nc. NYLON LOCK S/S

051-0630 NUT 1/2"-13 S/S

051-0783 WASHER 3/8" FLAT THICK S/S

056-0125 HITCH PIN CLIPS 3mm X 60mm S/S

4

12

2

4

6

6

1

1

4

2

1

QT.

2

1

6

13

11

DETAIL A

8

4

1

MACHINE

PART

ITEM

MAT.

650A

BASE MACHINE ASSY

CNC

3D DWG BY

SBU

2D DWG BY

AG

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

DATE

14-07-14

14-08-04

ST-GERMAIN DE GRANTHAM

QUEBEC CANADA

N.T.S.

DEPT.

M

QTY.

1

NO.

005C0352

3

1

2

8

LET.


4

7

5

1

005A1524


001B6779 VALVE SUPPORT BRACKET

7

8

5

6

2

3

4

051-0144 SCREW #10-24 N.C 1/2"PAN PHIL. S/S

051-0572 NUT #10-24 NYLON LOCK S/S

100-0225 CLOSE NIPPLE 1/4" NPT SS

100-0463 TEE 1/4" NPT S/S

102-0361 Y BRANCH 1/4'' MNPT X 3/8'' T. QUICK

102-0410 MALE CONN.1/4"MNPTx3/8"T.QUICK

106-00701 VALVE 3WAY 24V 1/4''NPT

1

2

4

1

QT.

1

4

1

1

6

MACHINE

PART

ITEM

MAT.

650A

BELLOWS VALVE ASSY

CNC

3D DWG BY

SBU

2D DWG BY

XX

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC


QUEBEC CANADA

N.T.S.

DEPT.

M

QTY.

DATE

DATE

1

14-07-17

YY-MM-DD

NO.

005A1524

3

1

2

005A1519


1 004A4238 RIGHT REAR ACCESS DOOR PRE-ASSY

2 056-2600 SPRING PAWL LATCHE SS KNOB

3 051-0071 SCREW 4-40 x 1/4" RND SLOT S/S

4 051-0541 NUT # 4-40 NYLON LOCK SS

4

QT.

1

2

4

4

A

LET.


DETAIL A

MACHINE

650A

PART

ITEM

RIGHT REAR ACCESS DOOR ASSY

CNC

MAT.

DWG BY

SBU

APP. BY

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

DATE

13-09-16


QUEBEC CANADA

N.T.S.

DEPT.

M

QTY.

1

NO.

005A1519

5

13

2

4

3

10

8

9

DETAIL B

11

7

12

DETAIL A

6

1

005C0465


004A4090 ACCESS DOOR ASSEMBLY

5

6

7

2

3

4

004A4098 ELECTRIC BOX ASS'Y

004A4138 VACUUM SENSOR FILTER

004C0138 STRUCTURE PRE-ASSY

036-0265 GROMMET 1-1/2'' ID X 2-3/8'' OD RUBBER

036-0409 PRESSE-ETOUPE CD13

051-01385 SCREW 10-24 x 1/2"FLAT-UND. PHIL S/S

8

9

10

051-0144 SCREW #10-24 N.C 1/2"PAN PHIL. S/S

051-0180 BOLT. HEX. 1/4"-20 NC. x 1/2" S/S

051-0740 WASHER 1/4" FLAT S/S

11 056-3010-1 HINGE CONCEALED SS304 - BASE

12 056-3010-3 HINGE CONCEALED SS304 - PIN

13 102-0551 BULKHEAD 1/4"NPT X 3/8 TUBE QUICK

SILICONE ON EACH SIDE

AND ON TOP

SILICONE SUR CÔTÉ ET

DESSUS

4

4

2

8

2

2

1

3

1

1

8

QT.

1

1

B

A

1

MACHINE

PART

ITEM

MAT.

650A

STRUCTURE ASSEMBLY

CNC

DWG BY

SBU

APP. BY

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

DATE

14-07-16


QUEBEC CANADA

N.T.S.

DEPT.

M-(M)-I

QTY.

1

NO.

005C0465

LET.


2

3

004A4138


1 004A4139 VACUUM SENSOR FILTER SUPPORT

2 114-2020 FILTER / DRYER ¼"mnpt. X 1/4"t.p. COMP.

3 102-0410 MALE CONN.1/4"MNPTx3/8"T.QUICK

QT.

1

1

2

LET.


1

3

MACHINE

PART

ITEM

MAT.

VACUUM

VACUUM SENSOR FILTER

CNC

DWG BY

SBU

APP. BY

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

DATE

13-11-19


QUEBEC CANADA

N.T.S.

DEPT.

M

QTY.

1

NO.

004A4138

4

ITEM

11

12

13

14

15

16

PART # DESCRIPTION

051-0580 NUT 1/4"-20 S/S

051-0210 BOLT ¼"-20nc. X 1" S/S

051-0581 NUT 1/4"-20 NYLON LOCK S/S

051-0139 SCREW 10-24 x 1/2" FLAT PHIL S/S

028-0105 GROUND BARRIER (6 HOLES)

051-0128 SCREW 10-24 x 3/8'' TRUSS PHIL S/S

1

3

14

2

A

4

1

4

004A4098

QT.

ITEM PART #

4

4

4

1

2

3

DESCRIPTION

004A4099 E-BOX PRE-ASSY

056-3010-1 HINGE CONCEALED SS304 - BASE

056-3010-3 HINGE CONCEALED SS304 - PIN

7

8

9

10

4

5

6

004A4102 E-BOX FALSE BOTTOM

036-0430 PRESSE-ÉTOUPE CD29

036-0409 PRESSE-ETOUPE CD13

004A4100 E-BOX DOOR ASSEMBLY



051-0600 NUT 5/16" -18 S/S

16

5

PUMP

16

8

6

SEAL BAR

TOP BOTTOM OPTION

VALVES

MC-40

12

11

10

1

1

3

QT.

1

2

2

1

4

1

2

LET.

MODIFICATION

7

DATE INT.

13

15

9

NOTE:

DETAIL A

- 026-3161 - DISCONNECT SWITCH SHAFT: COUPER À

134 MM DE LONG.

MACHINE

PART

ITEM

MAT.

VACUUM

ELECTRIC BOX ASS'Y

CNC

DWG BY

SBU

APP. BY

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

DATE

13-09-23


QUEBEC CANADA

N.T.S.

DEPT.

M

QTY.

1

NO.

004A4098

4

5 CENTER WITH HANDLE

004A4100


1 004A4101 E-BOX DOOR PRE-ASSY

2 056-2612 CAM LOCK QUARTER TURN SS304

3 179-0026 D-SHAPED RUBBER SEAL 1683mm LONG

4 026-3160 HANDLE RED/YELLOW NEMA 4X,

COMPACT, PADLOCKABLE

5 127-0100 STICKER ELEC.HAZARD ISO 2-1/2''

TRIANGLE

QT.

1

1

1

1

1

16.4

434

2

LET.


1

3

418

MACHINE

PART

ITEM

MAT.

VACUUM

E-BOX DOOR ASSEMBLY

CNC

DWG BY

SBU

APP. BY

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

DATE

13-09-17


QUEBEC CANADA

N.T.S.

DEPT.

M

QTY.

1

NO.

004A4100

4

2

3

004A4090


1 004A4089 ACCESS PANEL PRE-ASSY

2 056-2600 SPRING PAWL LATCHE SS KNOB

3 051-0071 SCREW 4-40 x 1/4" RND SLOT S/S

4 051-0541 NUT # 4-40 NYLON LOCK SS

QT.

1

1

2

2

1

LET.


MACHINE

PART

ITEM

MAT.

VACUUM

ACCESS DOOR ASSEMBLY

CNC

DWG BY

SBU

APP. BY

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

DATE

13-09-11


QUEBEC CANADA

N.T.S.

DEPT.

M

QTY.

1

NO.

004A4090

16

12

2

16

14

6

7

A

DETAIL A

B

C

LET.

15

17

18

13

17

MODIFICATION

DETAIL C

DATE INT.

D

5

1

005A1518


001-1876 LOWER WIRE SUPPORT

11

12

13

14

15

8

9

10

5

6

7

2

3

4

002-0326

002-0327 RIGHT SEAL BAR GUIDE BLOCK

002-0390 COVER ARM COLLAR

004B0383 COVER ARM ASSY

004C0137 TABLE ASSEMBLY

005-0651

036-0409

051-0178

051-0185

LEFT SEAL BAR GUIDE BLOCK

BELLOWS ASSEMBLY

PRESSE-ETOUPE CD13

SCREW 1/4"-20 x 5/16" SKT SET S/S

SCREW 1/4-20x 1/2"PAN PHIL S/S

051-0212 SCREW 1/4"-20 x 1" PAN PHILL S/S

051-0250 BOLT ¼"-20nc. X 1½" S/S

051-0422 BOLT 3/8"-16nc. X 3¼" S/S



16

17



18 056-01675 KEY 1/4" SQ. x 1 1/4" ROUNDED END S/S

19 105-0450 METAL CABLE CLAMPS #6 SS

8

16

4

17

4

1

8

1

32

8

4

3

4

1

4

4

4

QT.

1

4

9

4

3

19

1

14

10

DETAIL D

PART

ITEM

MAT.

MACHINE

650A

TABLE ASSEMBLY W/ARM

CNC

3D DWG BY

SBU

2D DWG BY

AG

DETAIL B

DEPT. TOL.

USINAGE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

TOLERIE

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC


QUEBEC CANADA

N.T.S.

DATE

DATE

14-07-10

14-07-31

DEPT.

M

QTY.

1

NO.

005A1518

ITEM PART #

20 051-0760

DESCRIPTION

WASHER 5/16" FLAT S/S

21

22


075-1655 2 BOLT FLANGED BEARING 1-1/4"

PLASTIC

QT.

16

16

4

ITEM PART #

15 051-0441

DESCRIPTION

BOLT 1/2"-13 x 1 1/2" SS

16 051-0560 NUT #8-32 NYLON LOCK S/S

17

18

19

051-0600

051-0630

051-0720

NUT 5/16" -18 S/S

NUT 1/2"-13 S/S

WASHER #8 FLAT S/S

004C0137

QT.

8

ITEM PART #

1

DESCRIPTION

002A3941 SPRING ADJ. PIVOT

6

16

8

6

12

13

14

5

6

7

2

3

4

8

9

10

11

002A4002 SPRING ADJ. PIVOT SPACER

002B0331 CENTRAL SHAFT

004A3937 SHACKLE ASS'Y

004A3968 SPRING INSERT ASSEMBLY

005A1437 MICRO SWITCH COLLAR ASSY

005A1517 SPRING BLOCK PRE-ASSY

005C0355 TABLE WELDED ASSEMBLY

008A1953 SPRING

026-0750 ROLLER PLUNGER SWITCH SPDT

036-0400 WIRE CONNECT. 3/8'' NPT

CD09/O-RING/NUT

036-0400 WIRE CONNECTOR 3/8'' NPT NUT

051-0142 SCREW 8-32 x1-1/2"RND PHIL S/S

051-0300 BOLT 5/16"-18 x 3/4" S/S

8

3

2

8

4

QT.

8

16

3

8

1

8

8

6

16

PROCÉDURE D'AJUSTEMENT DES

RESSORTS / SPRING ADJUSTMENT

PROCEDURE:

- LES RESSORTS DOIVENT ÊTRE INSTALLÉ

LORSQUE LA TABLE EST INSTALLÉ SUR LE BATI.

- INSTALLER LES RESSORTS DE FAÇON LÂCHE ET

SERRER LES ÉCROUS À LA MAIN.

- TENDRE DE FAÇON ÉGALE LES RESSORTS. LA

LONGEUR ÉTIRÉ MOINS LA LONGEUR INITIAL DOIT

ÊTRE ÉGALE POUR CHAQUE RESSORT.

- NE PAS FAIRE PLUS DE 10 TOURS PAR RESSORT À

LA FOIS

------------

- SPRING MUST BE INSTALLED ONCE THE TABLE IS

ASSEMBLED ON THE STRUCTURE

- INSTALL THEM LOOSELLY BY THIGHTENING THE

NUT BY HAND

- TENSION SPRING EQUALLY. THE STRECHTED

LENGTH MINUS THE INITIAL LENGTH MUST BE THE

SAME ON EACH SPRING.

- DO NOT STRETCH THE SPRING BY MORE THAN

10 NUT TURN AT A TIME PER SPRING.

LET.


MACHINE

PART

ITEM

MAT.

650A

TABLE ASSEMBLY

CNC

3D DWG BY

SBU

2D DWG BY

SBU

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

DATE

14-07-09

14-10-08


QUEBEC CANADA

N.T.S.

DEPT.

M-I

QTY.

1

NO.

004C0137

4

7

3

6

11

59.4

59.4

AJUSTEMENT DE L'ARBRE / SHAFT ADJUSTMENT

- UTILISER LES CALES POUR POSITIONNER L'ARBRE

- CENTRER L'ARBRE HORIZONTALEMENT DANS LE TROU DE LA TABLE

------------

- USE BLOC TO SPACE THE SHAFT ACCORDINGLY

- CENTER SHAFT HORIZONTALLY IN THE TABLE HOLE

C

B

004C0137

22

21

18

15

2

14

20

9

5

17 1

DETAIL B

9

DETAIL A

A

8

17

MACHINE

PART

ITEM

MAT.

650A

TABLE ASSEMBLY

CNC

3D DWG BY

SBU

2D DWG BY

10

19

16

DETAIL C

DEPT. TOL.

USINAGE

METRIC INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC


TOLERIE

SOUDAGE

± 0.1

± 0.5

± 0.5

13

QUEBEC CANADA

N.T.S.

DATE

DATE

14-07-09

DEPT.

M-I

QTY.

1

NO.

004C0137

004A3968


1 002A3989 SPRING ADJUSTMENT ROD

2 051-0600 NUT 5/16" -18 S/S

3 002B3940 SPRING INSERT

QT.

1

2

1

2 3

2

1

B

A

LET.

AJOUT 420A ET 650A

AJOUTER 620A

MODIFICATION

14-08-04 SBU

13-01-23 J.G.

DATE INT.

MACHINE

PART

ITEM

MAT.

VACUUM

SPRING INSERT ASSEMBLY

CNC

DWG BY

J.G.

APP. BY

650A

620A

600A

420A

MACHINE

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

DATE

13-01-15


QUEBEC CANADA

N.T.S.

DEPT.

M-(M)

QTY.

LISTE

NO.

004A3968

8

4

4

2

QTY

B

A

LET.

AJOUT 420A ET 650A

AJOUTER 620A

MODIFICATION

14-08-04 SBU

13-01-23 J.G.

DATE INT.

2

004A3937


1 004A3935 SHACKLE PRE-ASS'Y

2 001A6269 SHACKLE PLATE

3 056-0118 COTTER PIN 3/32" x 1" S/S

QT.

1

1

1

1

3

MACHINE

PART

ITEM

MAT.

VACUUMS

SHACKLE ASS'Y

CNC

DWG BY

J.G.

APP. BY

650A

620A

600A

420A

MACHINE

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

DATE

12-11-06


QUEBEC CANADA

N.T.S.

DEPT.

M-(M)

QTY.

LISTE

NO.

004A3937

8

4

4

2

QTY

3

8

5

1 9 6

2

6

7

4

5

8

9

005F0548

ITEM PART #

1

2

3

DESCRIPTION

001-0269 SEAL BAR GUIDE

001B1900 INTERIOR BELLOWS COVER

001B1901 EXTERIOR BELLOWS COVER

002B4161 SEAL BAR SUPPORT (ECO)

004D0255 SEAL BAR PRE-ASS'Y

051-0230 HEX BOLT 1/4-20 x 1 1/4" SS

051-0251 CAP. HEX. SKT BOLT 1/4"-20 NC. x 1 1/2"



1

1

10

5

QT.

2

1

1

10

4

-ITEM #2 ÉGAL AVEC L'ITEM #4 & #5.

-ITEM #2 FLUSH WITH ITEM #4 & #5.

-END VIEW-

LET.


4

7

-BAG CUT OPTION-

MACHINE

650A, 680A & 700A

PART

SEAL BAR ASS'Y W/SUPPORT

ITEM CNC

MAT.

DWG BY

S.L.

APP. BY

700A

680A

650A

MACHINE

4

4

4

QTY

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

14-02-12

DATE


QUEBEC CANADA

N.T.S.

DEPT.

M-I-(M)

QTY.

LISTE

NO.

005F0548

7

6

ITEM PART #

1

2

004D0255

DESCRIPTION

002A4171 SEAL BAR

002A4172 BANDING BUCKLE

8

9

6

7

3

4

5

005A1443 ELEMENT BINDER RIGHT

005A1444 ELEMENT BINDER LEFT

027-0400 CONNECTOR ADAPTOR

039-02115 ROUND CUT-OFF ELEMENT 0.9MM

039-0222 TAPERED BAND 3MM X 0.3MM

051-0146 SCREW 10-24 X 1" PAN PHIL S/S


13

14

15

16

10 051-01752 SET SCREW 10-32 SS 3/16"

11 051-01752 SET SCREW 10-32 SS 3/16"

12 051-0550 NUT #8-32 SS

077-0014 SPRING C0240-040-1250 SS COMP.

171-0180 TAPE CLEAR SUPER BOND 3/4" 854.5mm (0.026)

176-0200 TEFLON TAPE, 5MIL

176-0203 TEFLON TAPE UNCOATED 5MIL (0.78)

4

2

1

1

2

2

8

1

1

1

1

2

2

6

QT.

1

4

OVER THE ELEMENT 16 INSTALLÉ SUR L'ÉLÉMENT

UNDER THE ELEMENT 15 INSTALLÉ SOUS L'ÉLÉMENT

PERMETTRE DE BOUGER LIBREMENT 3 ALLOW TO MOVE FREELY

12

1

LET.

13

8

DETAIL A


2

10

5

14

A

-BAG CUT (ECO) -

MACHINE

650A , 680A & 700A

PART

SEAL BAR PRE-ASS'Y

ITEM CNC

MAT.

DWG BY

S.L.

APP. BY

700A

680A

650A

MACHINE

4

4

4

QTY

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

DATE

14-02-12


QUEBEC CANADA

N.T.S.

DEPT.

M-(M)-I

QTY.

LISTE

NO.

004D0255

9

8

5

1

6

8

7

4

6

7

4

5

8

9

005D0549

ITEM PART #

1

2

3

DESCRIPTION

004B0256 SEAL BAR PRE-ASS'Y

002A0357 SEAL BAR SUPPORT

051-0251 CAP. HEX. SKT BOLT 1/4"-20 NC. x 1 1/2"

001A1900 INTERIOR BELLOWS COVER

001A1901 EXTERIOR BELLOWS COVER

001-0269 SEAL BAR GUIDE

051-0230 HEX BOLT 1/4-20 x 1 1/4" SS



1

1

2

10

QT.

1

1

5

8

10

ITEM #2 ÉGAL AVEC L'ITEM #4 & #5.

ITEM #2 FLUSH WITH ITEM #4 & #5.

-END VIEW-

I

LET.

004B0256 WAS 004A0256

MODIFICATION

13-08-12 SBU

DATE INT.

2

3

-TOP & BOTTOM SEALING OPTION-

MACHINE

650A, 680A & 700A

PART

SEAL BAR ASS'Y W/SUPPORT

ITEM

MAT.

CNC

DWG BY

SBU

APP. BY

700A

680A

650A

MACHINE

4

4

4

QTY

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

13-08-12

DATE


QUEBEC CANADA

N.T.S.

DEPT.

M-I-(M)

QTY.

LIST

NO.

005D0549

14

4


13

8

1

VOIR DÉTAIL A

6

3

7

6

11

DETAIL B

4

5

INSTALLER CONTRE L'ENCOCHE DE L'ITEM #2 11 INSTALL AGAINST NOTCH OF ITEM #2

G

AJOUT PINCE TEFLON, CHANGE TEFLON 13-08-12 SBU

LET.


3

14

12

8

9

10

11

12

6

7

4

5

ITEM PART #

1

2

3

13

14

004B0256

DESCRIPTION

002A4129 SEAL BAR

001-2666 ELEMENT BINDER



051-0100 SCREW 8-32 X 3/8" PAN PHIL S/S

051-0550 NUT #8-32 SS


179-0003 SILICONE 2mm x 15mm (0.9) 1

176-0220 TEFLON TAPE, PRESS SENSITIVE 2" (0.104) 1

039-0220 BI-ACTIVE SEALING ELEMENT (0.09)

056-1400 1/4"SET SCREW BANDING BUCKLE S/S

176-0203 TEFLON TAPE, 5MIL UNCOATED ZONE

854.5mm (0.085)

1

1

2

077-0095 SPRING C 0360-059-1250 S/S

001-0266 TEFLON HOLD DOWN PLATE

2

2

4

2

8

2

QT.

1

2

8

BEND AFTER SEAL BAND

INSTALLATION

PLIER APRÈS L'INSTALLATION

DE LA BANDE DE SCELLAGE

10

9

B

DÉTAIL A

TOP & BOTTOM

SEALING OPTION

MACHINE

580A, 650A, 680A & 700A

PART

SEAL BAR PRE-ASS'Y

ITEM CNC

MAT.

DWG BY

SBU

APP. BY

700A

680A

650A

580A

MACHINE

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

13-08-12

DATE


QUEBEC CANADA

N.T.S.

DEPT.

M-(M)-I

QTY.

LISTE

NO.

004B0256

4

4

4

2

QTY

A

3

CE COTÉ DE LA BARRE DOIT ÊTRE ÉGAL

AU SUPPORT

THIS SIDE OF SEAL BAR TO FIT FLUSH

WITH SUPPORT

K

AJOUT PINCE TEFLON, CHANGE TEFLON 13-08-12 SBU

LET.


6

15

1

10

11

12

16

005C0437

ITEM PART #

1

2

3

DESCRIPTION

002B0378 UPPER SEAL BAR SUPPORT

002C0396 UPPER SEAL BAR

051-0232 SCREW 1/4-20x 1-1/4"SKT CAP SS

8

9

10

6

7

4

5

11

001-2666 ELEMENT BINDER



051-0104 SCREW 8-32 x 3/8" RND PHIL S/S

051-0550 NUT #8-32 SS


179-0003 SILICONE 2mm x 15mm ADHESIVE 828mm

(0.83)

176-0220 TEFLON TAPE 0.010", PRESS SENSITIVE 2"

828mm (2.72)

12

13

14

039-0220 BI-ACTIVE SEALING ELEMENT (6mm) 871mm

(0.087)

056-1400 1/4"SET SCREW BANDING BUCKLE S/S

077-0095 SPRING C 0360-059-1250 S/S

15 001B1571 UPPER TEFLON HOLDER

16 176-0203 TEFLON TAPE UNCOATED 0.005", 828mm

(2.72)

6

4

2

1

9

2

2

9

QT.

1

1

8

1

1

8

9

8

2

2

1

2

2

15

5

DETAIL A

7

5

INSTALLER CONTRE L'ENCOCHE DE L'ITEM #4

13

13 INSTALL AGAINST NOTCH OF ITEM #4


-TOP & BOTTOM SEALING OPTION-

MACHINE

580A, 650A, 680A & 700A

PART

UPPER SEAL BAR ASS'Y W/SUPPORT

ITEM CNC

MAT.

DWG BY

SBU

APP. BY

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

13-08-12

DATE


QUEBEC CANADA

N.T.S.

DEPT.

QTY.

M-(M)-I

2

NO.

005C0437

11

LET.

1

INSTALLER TROU DE CE CÔTÉ

DU RÉSERVOIR D'HUILE

INSTALL THIS HOLE ON THE OIL

RESERVOIR SIDE

MODIFICATION

4

DATE INT.

2

7

9

8

1

005A1535


001B6563 PUMP SUPPORT

5

6

7

2

3

4

8

9

10

11

004A4240 BELLOWS ELBOW CONNECTOR ASSY

051-0360 BOLT 3/8"-16nc. X 1" S/S



051-09931 BOLT M10 X 20MM HEX SS

100-1250 STRAIGHT 2"MNPT X 2" HOSE BARB SS

104-0151 HOSE 2"ID VACUUM TIGERFLEX 560MM

105-0258 EAR CLAMP 2" S/S

125-0070 BUSCH RA-0165 230-460V/3PH/60HZ

125-0075 BUSCH RA-0165 575V/3PH/60HZ

QT.

2

1

8

8

20

4

1

1

1

1

2

10

3

5

6 USE BLUE LOCTITE

165M³ BUSCH PUMP

MACHINE

PART

ITEM

MAT.

650A

PUMP "BUSCH" 165M³

CNC

3D DWG BY

SBU

2D DWG BY

SBU

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

SIPROMAC

DATE

DATE

14-10-08

14-10-08


QUEBEC CANADA

N.T.S.

DEPT.

M-I

QTY.

1

NO.

005A1535

LET.

3

4

2

MODIFICATION

DETAIL A

DATE INT.

7

13

15

14 12

1

005A1522


004-0183 VAC./ATM. VALVE SUPP. PRE-ASS'Y

11

12

13

14

15

8

9

10

16

17

5

6

7

2

3

4

051-0360 BOLT 3/8"-16nc. X 1" S/S



100-0095 STREET ELBOW 90° X 2'' NPT SS

100-0250 CLOSE NIPPLE 2" NPT SS

100-0250 CLOSE NIPPLE 1-1/2"NPT S/S

100-0487 TEE 2"npt. S/S

100-0558 RED. BUSHING 2"mnpt. X 1"fnpt S/S

100-0561 RED.BUSH. 2"NPTx1-1/2"NPT SS


104-0151 HOSE 2"ID VACUUM 572MM


105-0120 SCREW CLAMPS 1-13/16'' TO 2-3/4'' ALL S/S


106-0051 VALVE 2WAY 24V 1-1/2"NPT60Hz

106-0060 VALVE 2WAY 24V 2'' NPT(B80) 60HZ

1

1

3

1

3

1

1

2

1

1

2

3

2

4

1

QT.

1

2

OUT

11

5

17

OUT

IN

9

8

IN

6

16 A

10

7

1

-OPTION - 165M³, 255M³ & 305M³ PUMP

MACHINE

VACUUM

PART

VACUUM/ATMOSPHERE VALVE ASSY

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

N.T.S.

SIPROMAC


QUEBEC CANADA

ITEM

MAT.

CNC

DWG BY

SBU

APP. BY

DATE

DATE

13-09-18

DEPT.

M

QTY.

1

NO.

005A1522

LET.

MODIFICATION

15

IN

DATE INT.

11

12

13

1

005A1521


004-0183 VAC./ATM. VALVE SUPP. PRE-ASS'Y

11

12

13

14

8

9

10

15

16

5

6

7

2

3

4

051-0360 BOLT 3/8"-16nc. X 1" S/S



100-0095 STREET ELBOW 90° X 2'' NPT SS

100-0250 CLOSE NIPPLE 2" NPT SS

100-0250 CLOSE NIPPLE 1-1/2"NPT S/S

100-0487 TEE 2"npt. S/S

100-0558 RED. BUSHING 2"mnpt. X 1"fnpt S/S

100-0561 RED.BUSH. 2"NPTx1-1/2"NPT SS



105-0120 SCREW CLAMPS 1-13/16'' TO 2-3/4'' ALL S/S


106-0051 VALVE 2WAY 24V 1-1/2"NPT60Hz

106-0060 VALVE 2WAY 24V 2'' NPT(B80) 60HZ

1

1

2

1

1

1

1

1

1

2

2

2

4

1

QT.

1

2

OUT

16

OUT

5

7

10

IN

A

1

6

2

4

8

9

14

3

DETAIL A

-OPTION - 165M³, 255M³ & 305M³ PUMP

MACHINE

VACUUM

PART

VACUUM/ATMOSPHERE VALVE ASSY

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

N.T.S.

SIPROMAC


QUEBEC CANADA

ITEM

MAT.

CNC

DWG BY

SBU

APP. BY

DATE

DATE

13-09-18

DEPT.

M

QTY.

1

NO.

005A1521

ITEM PART #

8 104-0151

DESCRIPTION

HOSE 2"ID VACUUM TIGERFLEX 560MM

9 105-0258 EAR CLAMP 2" S/S

10

11

12

13

125-0080

125-0085

125-0087

125-0088

BUSCH RA-0255 230-460V/3PH/60HZ

BUSCH RA-0255 575V/3PH/60HZ

BUSCH RA-0305 230-460V/3PH/60HZ

BUSCH RA-0305 575V/3PH/60HZ

10 11 12 13

2

1

1

1

1

QT.

1

2

1

005A1520


001B6563 PUMP SUPPORT

5

6

7

2

3

4

004A4240 BELLOWS ELBOW CONNECTOR ASSY

051-0360 BOLT 3/8"-16nc. X 1" S/S



051-09931 BOLT M10 X 20MM HEX SS


7

9

QT.

2

1

8

8

20

4

1

8

SMALL HOLES MUST

BE ON OIL RESERVOIR SIDE

3

5

5

4

A

LET.

001B6563 WAS 001A6563

MODIFICATION

14-05-28 SBU

DATE INT.

USE BLUE LOCTITE 6

1

-OPTION - 255M³ & 305M³ PUMP

MACHINE

650A

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

PART

PUMP "BUSCH" 255 & 305 M³

N.T.S.

ITEM

MAT.

CNC

DWG BY

SBU

APP. BY

DATE

DATE

14-07-16

SIPROMAC


QUEBEC CANADA

DEPT.

M-I

QTY.

1

NO.

005A1520

1

004B4113


1 106-0010 VALVE 2WAY N.C. 24VAC 1/4'' NPT(SMC)

2 102-0330 ELBOW 1/4" NPT X 3/8" HOSE QUICK

3 100-0065 STREET ELBOW 1/4" NPT SS

4 102-0361 Y BRANCH 1/4'' MNPT X 3/8'' T. QUICK

QT.

1

1

1

1

2

A

LET.

VALVE UPDATE

MODIFICATION

14-05-27 SBU

DATE INT.

3

4

-OPTION - GAS

MACHINE

PART

ITEM

MAT.

VACUUM

GAS VALVE ASSEMBLY (OPTION)

CNC

DWG BY

SBU

APP. BY

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

DOUBLE CHAMBER

SINGLE CHAMBER

MACHINE

SIPROMAC

2

1

QTY


QUEBEC CANADA

N.T.S.

DATE

DATE

14-05-27

DEPT.

M

QTY.

LISTE

NO.

004B4113

AIR PRESSURE

TO OTHER VALVE

6

5

6

4

6

FROM PUMP

8

7

TO BELLOWS

004B4105


1 001B6779 VALVE SUPPORT BRACKET

2 051-0144 SCREW #10-24 N.C 1/2"PAN PHIL. S/S

3 051-0572 NUT #10-24 NYLON LOCK S/S

4 100-0225 CLOSE NIPPLE 1/4" NPT SS

5 100-0463 TEE 1/4" NPT S/S



8 106-00701 VALVE 3WAY 24V 1/4''NPT

1

1

3

QT.

1

4

4

1

1

1

3

2

A

LET.

UPDATE VALVE

MODIFICATION

14-05-27 SBU

DATE INT.

-OPTION - AIR REGULATOR

MACHINE

VACUUM

PART

BELLOWS VALVE ASSY (OPT AIR REG)

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

N.T.S.

ITEM

MAT.

CNC

DWG BY

SBU

APP. BY

DATE

DATE

14-05-27

SIPROMAC


QUEBEC CANADA

DEPT.

M

QTY.

1

NO.

004B4105

40°

A

LET.

VALVE UPDATED

MODIFICATION

14-05-27 SBU

DATE INT.

AIR PRESSURE

INLET

6

4

5

VACUUM FROM

OTHER VALVE

004B4103


1 004A4140 AIR REGULATOR SUPPORT

7 100-0065 STREET ELBOW 1/4" NPT SS

3 100-0225 CLOSE NIPPLE 1/4" NPT SS

2 100-0463 TEE 1/4" NPT S/S



8 106-00701 VALVE 3WAY 24V 1/4''NPT

4 114-0147 PRESSURE REGUL. 0-60 PSI 1/4" NPT

5 114-0245 PRESSURE GAUGE 60 PSI 1/8" NPT

3

6

AIR PRESSURE

TO OTHER VALVE

2

1

1

3

1

QT.

1

2

1

1

1

1

9

TO BELLOWS

7

6

8

-OPTION - AIR REGULATOR

MACHINE

600A & 620A

DEPT. TOL.

USINAGE

TOLERIE

SOUDAGE

METRIC

± 0.1

± 0.5

± 0.5

INCH

± 0.004"

± 0.020"

± 0.020"

PART

AIR REGULATOR VALVE ASSY

N.T.S.

ITEM

MAT.

CNC

DWG BY

SBU

APP. BY

DATE

DATE

14-05-27

SIPROMAC


QUEBEC CANADA

DEPT.

M

QTY.

1

NO.

004B4103

SIPROMAC 650A vacuum packaging machine OWNER’S MANUAL

Assistant Bot

OWNER’S MANUAL

MANUEL DE L’UTILISATEUR

VACCUM MACHINE

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Do not pour oil or other fluids into the ground, down a drain or into a body of water

Warning-Your responsibility

VACUUM PACKAGING MACHINE

MODEL 650A

(MC-40 SIPROMAC)

VACUUM PACKAGING MACHINES

OPERATION INSTRUCTIONS

SIPROMAC INC.

VACUUM PACKAGING MACHINES

-MENUS STRUCTURE-

-KEYBOARD DETAILS-

MC-40 CONTROLS

MODEL 650A

COVER ADJUSTMENT PROCEDURE

MECHANICAL DRAWING

DETAIL A

A

DETAIL B

B

DÉTAIL A

TOP & BOTTOM

SEALING OPTION

A

DETAIL A

-TOP & BOTTOM SEALING OPTION-

165M³ BUSCH PUMP

-OPTION - 165M³, 255M³ & 305M³ PUMP

-OPTION - 165M³, 255M³ & 305M³ PUMP

-OPTION - 255M³ & 305M³ PUMP

-OPTION - GAS

-OPTION - AIR REGULATOR

-OPTION - AIR REGULATOR

Key Features

Frequently Answers and Questions

How do I set the vacuum level on the 650A vacuum packaging machine?

What are the different operating modes available on the 650A vacuum packaging machine?

How do I clean the 650A vacuum packaging machine?

Related manuals

Sipromac

SIPROVAC 620A

Sipromac

380T

Berkel

450A

Berkel

250 Series Vacuum Packaging

Berkel

250

Berkel

550A

Berkel

Crib Toy 550A

Berkel

Vacuum Cleaner BK45767

Berkel

450A

CombiSteel

7004.0045

CombiSteel

7004.0040