User Manual
YDM 3109
User Manual
Keep this manual safe for future reference
※The functions and design of this product can be changed without notice for quality improvement.
※Chinese manual is from 33 page.
ISL-1213-00 rev.1
Please read the following before using your Yale product
IMPORTANT SAFETY
INSTRUCTIONS
Please read the following safety instructions to prevent any accident, property damage and
inconvenience. Children should be well educated for the operating instruction. Keep this
manual in a convenient place so that you can refer to it when necessary.
•This
product is designed and manufactured to assure personal safety. Improper use can result in personal damage or
property loss. Please observe the procedures for installation, use and servicing.
Yale is a precision electronic device. All safety and operating instructions should be read before the
•
must be followed to protect yourself and your property.
product is operated.
•Refer
all servicing to qualified service personnel. Servicing is required when the product is damaged or to be re-installed.
your installation conditions with the local service provider before installation as your door prep might be different
from the standard this lock conforms with.
explains product functions and features.
•Check
prohibited
must observe
•The
products warranty does not cover defects or damages arising from the door defects, improper installation, lack of or
improper maintenance, improper storage, shipping and handling, ordinary wear and tear, misuse, abuse, accident,
unauthorized service or use with unauthorized service parts.
•Disassembly,
rework and reverse engineering are prohibited without a written approval of Yale except for a normal
installation of the product.
•The
trademarks, trade names, designs, copyright, patents and other proprietary right used on or embodied in the product
and this manual shall remain the exclusive property of the manufacturer, cannot be copied or used in any form without
the written authorization by Yale.
02
•Visit
our website www.yaledigital.com.cn for more information on the products.
•The
information in this manual is subject to change without notice.
Yale digital door lock is
a precision electronic
device.
Clean only with dry
cloth. Do not use water
that can cause damage
to the electronic circuit.
Do not attempt to
disassemble the unit
by yourself. That can
cause an electronic
shock and product
damage.
When you move,
contact your local
service personnel
for re-installation.
Check the service
charge with your
service provider.
Overview
Do not use an
inappropriate tool
that can cause
damage or malfunction of the product.
Handle the unit
with care.
Excessive force,
careless handling
may cause product
damage.
Be careful not to have
an unauthorized user
know your security
code. Change your
code periodically.
Do not use water and
any type of solvent
such as gasoline or
benzene as they can
cause damage to
electronic circuit,
deterioration and/or
paint peel-off.
Do not have your
card key lost or
stolen.
■ Immediate re-registration
of all remaining keys is
required to invalidate the
lost key.
■
Proximity card identification
Triple access
You can unlock the door by the card, the security code or the
mechanical key at your convenience. You do not need to worry
about accidental lockouts by losing or forgetting the key.
Make sure the door
is securely locked
whenever you
leave your house,
especially in the
manual lock mode.
Make sure the distance
between the door and
door frame is not
widened more than
5mm.
Keep card key reader
part clean and dry.
Dust off dirt smoothly
with a soft cloth.
Remove all of the
batteries before
installing or
removing a remote
control module.
■
■
5mm
■
■
Break-in / Damage alarm
80dB alarm will go off if anyone attempts to damage the lock or
forces the door open.
Volume control
You can change the volume. The break-in alarm still operates
even if the silent mode is on.
■
Forced lock mode
Internal forced lock prevents anyone to unlock from the outside
and external forced lock makes only manual thumbturn
available to open the lock from the inside.
■
Remote control
You can use a remote control by installing the applicable
Remote control module. (This option may not be available
depending on your country or local dealer.)
Automatic locking
Just closing the door will automatically lock the door. Manual
operation is also available.
Emergency power supply
When the batteries are completely discharged you can easily
supply emergency power to the lock with the 9V battery.
Easy and simple operation
One-touch operation allows every user including children and
senior the simplest use.
■
■
Anti-collision
Contacting multiple cards does not cause error to the lock. The
card key reader will recognize the card key among a pack of cards.
Verification with the palm
The security code is verified by palm touching to randomize any
fingerprint residues on the keypad so protect from exposing it.
Easy re-registration of keys
If you lose a key, you can invalidate the lost key by reregistering all other keys. You can register up to 40 card keys
to add users.
Safe handle
Protects from any break-in attempts through the safe handle.
■
■
■
Educate your
children about the
proper use of the
product.
■
You can use your ISO 14443 A type RFID card such as credit
card or pass card as your card key.
■
Smart Pad
Keypad displays functional operation with lighting.
Basic Operation
CONTENTS
Please do remember below operation!
1. Card Key Registration
4. Unlocking the door from the outside
7. Volume control
Specifications
08
Identification of Product
09
① Contact Card key
Press
button Contact all the keys
you wish to register
on one by one
Press
button
② Wake up the lock with the palm touch, enter the
security code and retouch the lock with the palm.
2. Security Code Registration
① Mute : [Volume] Button
How to use
② Normal : [Volume] Button
1. Registering Card Keys
11
2. Registering Security Code
13
3. Locking the door from the outside
14
4. Unlocking the door from the outside
Press
button Enter the security code Press
(6~12digits)
button
① Contact the card key on [card key reader], or
3. Locking the door from the outside
① The automatic Lock Sensor detects the door
closing and locks the door within 5 seconds, or
② Touch the keypad with palm for locking the
door in
[Manual Lock Mode]
6. Forced Locking
① Forced Lock Mode from inside.
② Forced Lock Mode from outside.
or
Manual Lock Mode :
Press [
] Button.
With the
palm
Contact
5 seconds
Contact [ ]
3 seconds after put
security code
2. Remote control
28
Cautions
2. Lost card key
31
15
3. Product malfunction
31
5. Locking the door from the inside
17
4. Emergency mechanical key override
32
② Enter the security code, or
6. Unlocking the door from the inside
17
③ Press and hold [
7. Enabling/disabling Safe handle
18
Chinese Manual
33
8. Automatic / Manual Lock Mode
20
9. Forced Lock Mode
21
10. Break-in / Damage alarm
22
11. Wrong-try Lock-out
23
12. Volume control
24
13. Battery use & Replacement
25
14. Displaying operation status (Smart Pad)
26
8. Turning off the alarm
② Manual Lock Mode :
Press [
] Button
27
30
5. Automatic / Manual Lock Mode
① Automatic Lock Mode :
Press [
] Button
1. Remote control module
1. Emergency power supply
③ Loud : [Volume] Button
Security Code
Option
] button for 5 seconds
9. Emergency power supply
9V Battery can be
used to supply
electricity to the unit.
Specifications
Parts
Identification of Product
Specifications
Remarks
Front (Front Body)
68.6(W) x 306.6(H) x 27(D)(70.6)mm, Zinc die-casting
Back (Main Body)
72.8(W) x 306.6(H) x 37.0(D)(80.8), Flame-Retardant ABS, Zinc D/C
1. Front
(Front Body, install on the outside of the door)
Operating temperature : -15~55℃ (5~131˚F)
Card Keys
Battery
Lock case
Option
Remote Control
Zinc die-casting
Card Key Reader
4 EA
Up to 40 keys (sold separately)
4EA 1.5V AA alkaline batteries (Operating voltage: 4.5 ~ 6 V)
Last up to 10 months (10 times used a day)
Dead Bolt Jam Lamp
Steel and SUS304
Wireless
Lock case
Battery Change Lamp
Latch Bolt
Lever
Optional
※Battery life may vary depending on temperature, moisture levels, frequency of use and the quality of the batteries.
※Please make sure that all parts are included when purchasing the product.
※Optional products may not be available depending on your country or local dealer.
※Pull down
Emergency Cover
Identification of Product
Lever
Keypad (10-Key)
Automatic
Locking Sensor
Reset button
■Basic Contents
■Option
Emergency Power
Supply Terminal
Dead Bolt
• 4 Card keys
• Emergency keys
• Screws
• Installation Template
• 4 Batteries
• Users Manual
Emergency Key
9V Emergency battery
(Optional)
Emergency Cover
Front (Front Body)
08
Back (Main Body)
Lock case
Remote control
Remote control module
09
How to Use
2. Back (Back Body, install on the inside of the door)
1. Registering Card Keys
1.5V AA Alkaline Batteries (4EA)
Battery Cover
▣ Keep the door open while you register card key to prevent yourself from accidentally
Slot for Remote control
module(Option)
getting locked out.
Registration button
Lever
How to Use
Auto / Manual Lock button
Volume Control Switch
Safe handle button
▣
▣
Manual thumb turn
4 card keys are provided at
purchase and you can register
up to 40 card keys.
If you lose your current card
key, re-register all the remaining
keys to invalidate the lost key.
▣
▣
Contact your local dealer for additional
card keys.
ISO 14443 A type RFID card can be
registered as your card key.
Internal Forced Lock Switch
All card keys should be registered at a time.
10
11
2. Registering Security Code
Press
[Registration] button
Contact all the card keys
you wish to register on the
[card key reader] one by one
Press
[Registration] button
Check the key
operation
▣ Keep the door open while you register the security code to prevent yourself from accidentally getting locked out.
▣
12
•The numbers of registered
cards are shown on the
keypad.
The registration is
completed with a “pi-bibing” sound.
Opening the door with
your card key. Contact
your card key to [card
key reader]
Press
[Registration] button
Enter your security
code
Press
[Registration] button
Opening the door
with your card key
Touch the keypad with the
palm
Contact card key
Open [Battery Cover] and
Press
[Registration]
button.
Enter the code you wish
to register. (6~12 digits)
If it takes too long (over
7 seconds) to enter the
code after pressing
[register security code]
button, the code will not
be registered.
<
> and <
>
buttons can not be used
for security codes.
The registration is
completed with a “pi-bibing” sound.
•When registering the
security code, it shows
what the user has just
registered in order.
Check your security
code
How to Use
If it takes too long (over 7
seconds) to contact a
card key after pressing
[Registration] button,
the card will not be
registered.
If you hear a “pik” sound, the
card keys are registered.
If you hear a “ti-to-ti-to” sound,
the card key had been already
registered.
Set a code of 6~12 digits using the number buttons
▣ The old code is automatically deleted when registering a new code.
Pik
Open [Battery Cover] and
Press
[Registration]
button.
(6 digits)
(12 digits)
000000 ~ 000000000000
Once registration
is completed,
make it sure to
open the lock
with your new
security code.
Opening the door with your
code
Touch with the palm [keypad]
Enter security code
Touch with the palm [keypad]
13
3. Locking the door from the outside
4. Unlocking the door from the outside
※Please check Automatic / Manual Lock Mode
Automatic
lock mode
The automatic lock sensor detects the door
closing and locks the door automatically
within 5 seconds.
Within 5
seconds
Di-di-ding
Contact card key
Confirming the door open
Pi-bi-bi
ng
The door locks when touch the keypad
with the palm.
Manual
lock mode
Di-di-ding
Security
code
(Normal)
Touch the keypad
with the palm
Enter your
security code
Touch the keypad
with the palm again
or press
button
or
As the automatic lock function does not work in manual lock mode, make sure to check that the door is securely locked
when leaving the premises.
14
How to Use
Unlocking
the door
with card
key
Confirming the
door open
Pi-bi-bi
ng
Confirming the lock
unlocked with a “pibi-bing” sound
•The keypad cannot be operable in case of wearing the glove.
•Using the palm or pressing
button do the same function after entering the security code.
•If the card key does not work properly, please contact the card key after touching the keypad with the palm.
15
Opening the lock by the fake PIN code
5. Locking the door from the inside
•This explains how to open the lock with the fake PIN code.
Touch the
keypad with
the palm
Press any number (fake PIN
code) and the right PIN code
Touch the
keypad with the
palm or press
button
Confirming
Automatic
lock mode
Use [manual thumb turn] on the
back body.
Fake PIN code ➔ Right PIN code
or
or
Right PIN code ➔ Fake PIN code
Please slightly
touch the exterior
keypad.
•This feature is not working when the lock is
locked down due to wrong-try lock-out delay.
Within 5 seconds
Please slightly touch
the exterior keypad
or press
button
to finish.
Pi-bi-bi
ng
How to Use
Opening
the lock
by the
fake PIN
code
When set on automatic lock mode,
the automatic lock sensor detects
the door closing and locks the door
automatically within 5 seconds.
Manual
lock mode
The lock is unlocked
with melody (“Pi-bibing”)
6. Unlocking the door from the inside
•When any incorrect PIN codes are inputted five times in a row, it turns the lock down for three minutes.
•When this function is on, the user cannot use the fake PIN code function until any normal verification through key, card, fingerprint, PIN code,
or opening the lock from inside is made. So, the user is encouraged to use the right PIN code without any fake number to verify the lock.
Down the lever
while pressing
the Safe handle
button
① Down the lever while pressing
the Safe handle button
② Turn the manual knob
Pi-bi-bing
•Use the fake PIN code feature whenever there is any chance of exposing the right PIN code to others.
16
17
7. Enabling/disabling Safe handle
YDM3109 protects from any break-in attempts through the Safe handle button.
Egressing when the Safe handle egress button is on
Factory default : Enabled status
Enabled
status
Disabling
Safe handle
Enabling
Safe handle
Take out the hexagon
wrench which is docked
in the battery cover.
The hexagon wrench
Take out the hexagon
wrench which is docked
in the battery cover.
The hexagon wrench
fixing bolt
Example
fixing bolt
Safe handle
button
How to Use
Safe handle
button
Down the lever while pressing the
Safe handle egress button
Disabled
status
Turn the fixing bolt on
the side of the inner
lever to the right
while pressing the
Safe handle button.
Turn the fixing bolt on
the side of the inner lever
to the left until the Safe
handle button pops out.
•The
locking bolt would not be retracted in case of not pressing the button.
•When the fire detection sensor is on, the feature is still on so the user must follow the usual procedure to open the door.
Be careful not losing the fixing bolt when you loosen it to set the feature on.
18
19
8. Automatic / Manual Lock Mode
9. Forced Lock Mode
Automatic locking sensor which detects the door closing and automatically locks the door in 5 seconds. Automatic lock
mode is a factory default setting.
External forced lock mode
①
Push up the Button
on
Mode.
Manual Mode
Automatic Mode
Setting
external
forced lock
mode on with
the card key
Contact card key
Confirming external forced Lock
Contact the card key on
[card key reader] for 5
seconds until you hear 3
beeps.
External forced lock
mode is set on with
“Di-ri-ric” sound.
How to Use
Setting it on
automatic lock
mode
5 seconds
②
Setting it on
manual lock
mode
Push down the Button
on
Mode.
Automatic Mode
Manual Mode
Setting
external
forced lock
mode on with
the security
code
Touch the keypad
with the palm
Enter the
security code
Press
button for
3 seconds until you
hear 3 beeps
Confirming
external forced
Lock
External forced lock
mode is
completed
with “Di-ri
-ric” sound.
Internal forced lock mode
When internal forced lock mode is on, the keypad is not functioning.
20
18
A warning beep sound will go off if anyone attempts to verify by the security
code or the card from outside.
Turn the mode
21
10. Break-in / Damage alarm
11. Wrong-try Lock-out
No keypad function is available during this wrong-try lock-out delay.
The break-in and damage alarm work regardless of this function.
80dB alarm goes off when the lock is damaged or anybody
breaks in by force while the door is locked.
Enter your security
code
(Choose one of the four options below.)
Press
[Unlock]
button on the remote
control
Press and hold
[Registration] button
for 5 seconds
Contact your card key
5 times
The lighting digit on the keypad
is showing remaining time
•The system will resume the operation
or
22
Lock-out 3 minutes
How to Use
Turning off the alarm
•If incorrect security codes or unregistered
card keys are attempted 5 times in a row,
it will lock out for about 3 minutes with the
blinking LED.
or
or
Resuming
automatically after 3 minutes of lock-out.
If you press
[Registration] button on
the back body or down the lever while
pressing the Safe handle egress button,
it resumes the operation.
23
12. Volume control
This function can control the operating sounds so that the door can be opened and closed without disturbing others.
❶ Silent Mode
Setting the volume Button on “ 0 ”
Setting the volume Button on “ 1 ”
❸ Loud Mode
Setting the volume Button on “ 2 ”
■ Battery life
(stand alone)
This product uses 4 1.5V
alkaline AA batteries which
can be used approximately 10
months on the condition of 10
times open/close cycles per
day.
1.5V AA size alkaline battery
10 months
1:1 actual size
■Battery replacement
warning
Replace all 4 batteries when
the low battery war ning
melody rings and the LED
turns red. (Use authentic
alkaline batteries)
Do not mix new and
used batteries.
The LED turn red
LED
(Red)
※ Battery life may
vary due to
temperature,
moisture,
frequency of
use, and the
quality of the
batteries.
How to Use
❷ Normal Mode
13. Battery use & Replacement
When a
low battery
warning
melody rings
•Always check + and - directions when inserting batteries.
•Use the authentic alkaline batteries. It is a user’s responsibility for damage
caused by using unauthentic batteries.
•Dispose of used batteries according to the instructions.
※RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE NATIONAL CODE OR RECYCLING PROGRAM.
24
25
Option
14. Displaying operation status (Smart Pad)
❶ Battery Replacement warning
❹ External / Internal forced locking
Starting from the left column, the LED
comes on from left to right to left for
twice.
Battery Icon lights on.
1. Remote control module
Remote control module should be installed in advance to use remote control.
Open [battery cover] and insert the module into the slot. Proper functioning of
the module can be checked by operating a remote control.
•Remote control module :
Required for the use of
remote control
Installing remote control module
❺ Break-in / Damage warning
❷ Dead Bolt locking motion warning
The LED keeps coming on to the
clockwise when a break-in or damage
is happened.(Alarm lasts for 30 minutes)
Locking Icon lights on.
26
Confirming
When registering the security code,
it shows what the user has just registered
in order.
(Right : In case of registering 1, 2, 3, 4, 5
and 6)
❼ Card Key registration
1 minute
passed
➞ 2 minutes
remaining
Put batteries back
in (Check + , directions)
Option
If incorrect security codes or unregistered card keys
are attempted 5 times in a row, it will lock out for about
3 minutes with the blinking LED.
Wrong-try Lock-out
warning starts
➞ 3 minutes
remaining
Insert remote control
module into the slot
❻ Security Code registration
❸ Wrong-try Lock-out warning
1 minute
passed
Open [battery
cover] and remove
all batteries
➞ 1 minute
remaining
When registering the card keys,
Keypad displays the number of registered
card keys.
(Right : is on ➞ 3 keys have been
registered)
Di-ri-ri-ri-ring
27
2. Remote control
Deleting remote control registration
The remote control is an FSK(Frequency Shift Keying) type that uses a Floating ID encoding system, which changes the
wireless code each time you use it, so that there is no risk of hacking. It is non-directional and the operational range is up
to 10~20m.
※Caution! The operational range may vary depending on the installation environment.
Re-registration automatically deletes the previous registered remote control.
Press
[Registration] button
Press
buttons
,
,
Press
[Registration] button
Deleting remote control
registration
Registering remote control
Press
[Registration] button
Press
buttons
,
,
Press [Registration]
button located on the
front of the remote
control with a pin
Press
[Registration] button
Remote control registration
is cancelled with a “di-ri-riring” sound.
Check remote
control operation
Option
How to use the remote control
You can register up to 5
remote controls
consecutively. In order to
register consecutively,
press [Registration] button
on eaeh remote control
with 10 second intervals.
Remote control makes a
beep when it is properly
registered.
28
Locking the door
Press
[close] button, and the door
will lock within 2~3 seconds.
Unlocking the door
Press
[open] button, and the door
will unlock within 2~3 seconds.
Changing the batteries
Open up the battery cover at the back of the
remote control and change the batteries.
Press [open] or
[close] button to
check the
operation
29
Cautions
1. Emergency power supply
2. Lost card key
In case the batteries are completely discharged 9V battery can be used to supply electricity to the unit. Unlock with the card
key or security code while contacting a 9V battery just like the below instruction. Discharged batteries should be replaced
right away.
If you lose your card, rest of card keys must be re-registered to invalidate
missing one.
Lost card key
Discharged
Holding a 9V
battery
Security code use
Change
Batteries
Confirming
Enter the security code in case you lose the card key or you are not carrying it.
※It is a user’s liability to break the lock because the user did not register any
security code.
Open the
door
3. Product malfunction
Press reset button located in the left of [emergency power terminal] with a pin and
try again with the key or the security code.
If it still does not work, call for after-sales service.
Replace all of the
batteries
Check out if a card
key and security
code work properly
after replacing all
batteries.
Reset Button
Cautions
Touch the keypad with the
palm. Enter the security code
and retouch the keypad or
press
button.
30
Re-registering card key
31
4. Emergency mechanical key override
Please operate the lock with the mechanical key when there is a problem to the lock or unlock the door that is the same
as below listed.
•Forgotten security code
•Electronic malfunction
※ Please slide the cover downward
A hole on
emergency key
Pull down the
emergency cover
• Keep the mechanical override key in a safe place.
Otherwise, you may not get a free after-sales service even within during the warranty period.
32
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement