Harman Kardon AVR 445 Owner's Manual

ENGLISH
AVR 445 Audio/Video Receiver
OWNER’S MANUAL
AVR 445
Downloaded from www.Manualslib.com manuals search engine
Table of Contents
3
4
4
5
7
10
14
16
16
16
17
18
20
21
21
23
23
23
23
24
25
26
27
28
30
31
33
34
35
36
36
38
38
38
39
39
40
40
40
40
41
41
41
42
42
43
43
43
44
44
44
44
45
45
45
45
46
46
46
47
48
49
49
49
49
49
Introduction
Safety Information
Unpacking
Front Panel Controls
Rear Panel Connections
Main Remote Control Functions
Zone II Remote Control Functions
Installation and Connections
Audio Connections
Video Connections
HDMI Connections
SCART A/V Connections
System and Power Connections
Speaker Selection
Speaker Placement
System Configuration
First Turn On
Using the On-Screen Display
System Setup
In/Out Input Setup
Audio Setup
Surround Setup
Night Mode Settings
Using EzSet/EQ
Manual Setup
Speaker Setup
Delay Settings
Output Level Adjustment
Additional Input Adjustments
Operation
Surround Mode Chart
Basic Operation
Source Selection
6/8-Channel Direct Input
Controls and Use of Headphones
Surround Mode Selection
Digital Audio Playback
Dolby Digital
DTS
PCM Audio Playback
Selecting a Digital Source
Digital Bitstream Indicators
USB Playback
Speaker/Channel Indicators
Night Mode
Using The Bridge™
Tape Recording
Front Panel Input/Output Connections
Output Level Adjustment with Source
EzSet/EQ Operation on/off Signals
Dim Function
Memory backup
Advanced Features
Front Panel Display Fade
Display Brightness
Turn-On Volume Level
Semi-OSD Settings
Full-OSD Time Out Adjustment
DMP The Bridge Auto Power
Multiroom Operation
Infrared Output Selection
Tuner Operation
Basic Tuner Operation
Station Selection
Preset Tuning
RDS Operation
2 TABLE OF CONTENTS
Downloaded from www.Manualslib.com manuals search engine
49
RDS Tuning
49
RDS Display Options
50
Program Search
51 Programming the Remote
51
Configuring the Remote
51
Preprogrammed Code Entry
52
Automatic Code Entry
52
Learning Commands
53
Learning Codes for an Input Selector
53
Device Priority
54
Macro Programming
56
Punch-Through Configuration
57
Renaming
59
Resetting the Remote
59
Backlight Options
61 Troubleshooting Guide
61
Processor Reset
62 Appendix
65 Technical Specifications
Declaration of Conformity
We, Harman Consumer Group, Inc.
2, route de Tours
72500 Château-du-Loir,
FRANCE
declare in own responsibility, that the product described in
this owner’s manual is in compliance with technical
standards:
EN 55013:2001+A1:2003
EN 55020:2002+A1:2003
EN 61000-3-2:2000
EN 61000-3-3.1995+A1:2001
EN 60065:2002
Jurjen Amsterdam
Harman Consumer Group, Inc.
09/06
Typographical Conventions
In order to help you use this manual with the remote control, front-panel controls and rear-panel
connections, certain conventions have been used.
EXAMPLE – (bold type) indicates a specific remote control or front-panel button, or rear-panel
connection jack
EXAMPLE – (OCR type) indicates a message that is visible on the front-panel information display
EXAMPLE – (Synchro type) indicates a message that is displayed on the remote control’s LCD screen
1 – (number in a square) indicates a specific front-panel control
– (number in a circle) indicates a rear-panel connection
0 – (number in an oval) indicates a button or indicator on the remote
A – (letter in an oval) indicates a button on the Zone II remote
The appearance of the text or cursor for your receiver’s on-screen menus may vary slightly from the
illustrations in this manual. Whether the text appears in all uppercase or upper- and lowercase
characters, performance and operation remain the same.
Thank you for choosing Harman Kardon!
With the purchase of a Harman Kardon AVR 445
you are about to begin many years of listening
enjoyment.
The AVR 445 has the most extensive range of
audio and video processing, control and connectivity options ever offered by Harman Kardon,
enabling it to provide the best possible audio
and video reproduction with any type of source
material. Teaming advanced processing circuitry
with proprietary technologies such as EzSet/EQ,
the AVR 445 seamlessly integrates every
component in your entertainment system to
deliver the best possible sound and images.
Some of the leading-edge features that are
available with the AVR 445, such as HDMI™
connectivity, are new to even the most
experienced home theater enthusiast.
To obtain the maximum enjoyment from your
new receiver, we urge you to read this manual.
A few minutes spent learning the functions of
the various controls will enable you to take
advantage of all the power the AVR is able to
deliver.
If you have any questions about this product, its
installation or its operation, please contact your
retailer or custom installer. They are your best
local sources of information.
Description and Features
The AVR 445 serves as the hub of your home
entertainment system, providing a wide range of
listening possibilities for almost any audio or
video program source, whether it is the broadcast of a movie or sporting event in HDTV or a
vintage mono or stereo recording. When playing
digital audio sources, the AVR 445 decodes
Dolby Digital, Dolby Digital EX, DTS and DTS-ES
data streams. Two-channel stereo and matrix
surround sources benefit from all current Dolby
Pro Logic IIx modes and DTS Neo:6. The latest
version of our proprietary Logic 7® process is onboard to create a wider, more enveloping sound
field and more defined surround channel positioning, regardless of the type of source material.
Additional audio playback and processing
options include a direct connection to
compatible computer-based sources through a
direct USB connection.
The AVR 445 takes the “video” part of its name
seriously. Along with two HDMI inputs and three
60MHz analog component video inputs, the AVR
445 converts incoming analog signals to component for single wire connections. Tying audio and
video together, the AVR 445 provides A/V sync
delay so that the lip sync errors –
commonly seen when digital video processing is
used in a source, program or video display – are
eliminated.
Coax and optical digital outputs are available for
direct connection to digital recorders, and both
the front panel analog audio/video and coaxial
digital jacks may be switched to outputs for use
with portable recorders – a Harman Kardon
exclusive. Two video recording outputs, preampout and a color-coded eight-channel input make
the AVR virtually future-proof, with everything
needed to accommodate tomorrow’s new formats right on board.
The AVR 445’s flexibility and power extend
beyond your main home theater or listening
room. The AVR includes a sophisticated multizone control system that allows you to select
one source for use in the main room and a
different one (Audio) in a second room.
Complete control over volume is possible with a
separate infrared control link. To make it easy to
operate the AVR from a remote room, a separate
“ZR 10” remote is included.
Additional multiroom options include the option
to assign two of the AVR’s output channels to the
multiroom system and the ability to link the AVR
to innovative A-BUS® keypads for multiroom
operation without the need for external amplifiers.
The AVR 445’s powerful amplifier uses traditional
Harman Kardon high-current design technologies
to meet the wide dynamic range of any program
selection.
Harman Kardon invented the high-fidelity
receiver more than fifty years ago. With state-ofthe-art circuitry and time-honored circuit designs,
the AVR is the perfect combination of the latest in
digital audio technology, a quiet yet powerful
analog amplifier in an elegant, easy-to-use
package.
■ Dolby* Digital, Dolby Digital EX and
Dolby Pro Logic* IIx Decoding, and the
full suite of DTS® modes, including
DTS-ES® 6.1 Discrete & Matrix and
Neo:6® and DTS 96/24.
■ Seven channels of high-current amplification with two channels assignable to
either surround back or multiroom
applications.
■ Harman Kardon’s exclusive Logic 7®
processing, along with a choice of
Dolby Virtual Speaker processing for
use when only two speakers are
available.
■ Dolby Headphone to create spacious,
open sound fields when using headphones.
■ USB connectivity for audio playback
with compatible computers and quick
system upgrades.
■ Two HDMI™ 1.1 and three assignable
high-bandwidth analog component
inputs for compatibility with the latest
high-definition video sources.
■ Harman Kardon’s advanced EzSet/EQ
automatically configures speaker
settings and sets room equalization for
quick, easy and accurate system setup.
■ High-bandwidth, HDTV-compatible
component video switching.
■ Front panel analog A/V inputs,
switchable to outputs.
■ Front panel digital inputs for easy
connection to portable digital devices
and the latest video game consoles.
■ Multiple digital inputs and outputs.
■ On-screen menu and display system.
■ Extensive multiroom options, including
a standard Zone II remote, assignable
amplifier channels and A-BUS/READY
capability for listening to a separate
source in a remote zone.
®
■ 6-Channel/8-Channel Direct Input and
Preamp Outputs for Easy Expansion and
Use with Future Audio Formats.
■ Extensive bass management options,
including Quadruple Crossover.
■ A/V Sync delay adjustable for each
input delivers perfect lip sync with
digital programs or video displays.
INTRODUCTION 3
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Introduction
Introduction / Safety Information
Important Safety Information
READ THIS BEFORE OPERATING
YOUR UNIT.
Do not install this equipment in a confined space
such as a case or similar – away from direct
sunlight, heat sources, vibration, dust, moisture,
and/or cold. Avoid installing this unit where foreign object may fall onto this unit and/or this
unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Burning objects (i.e. candles), as they may
cause fire, damage to this unit, and/or
personal injury.
– Containers with liquid in them, as they may
fall and liquid may cause electrical shock to
the user and/or damage to this unit.
Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat
radiation. If the temperature inside this unit
rises, it may cause fire, damage to this unit,
and/or personal injury.
Install this unit near the AC outlet and where the
AC power plug can be reached easily.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state
is called the standby mode. In this state, this unit
is designed to consume a very small quantity of
power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
Verify Line Voltage Before Use
Your AVR 445 has been designed for use with
220-240-Volt AC current. Connection to a line
voltage other than that for which it is intended
can create a safety and fire hazard and may
damage the unit.
If you have any questions about the voltage
requirements for your specific model, or about
the line voltage in your area, contact your dealer
before plugging the unit into a wall outlet.
Do Not Use Extension Cords
To avoid safety hazards, use only the power cord
attached to your unit. We do not recommend
that extension cords be used with this product.
As with all electrical devices, do not run power
cords under rugs or carpets or place heavy
objects on them. Damaged power cords should
be replaced immediately by an authorized
service depot with a cord meeting factory
specifications.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC
outlet, always pull the plug, never pull the cord.
If you do not intend to use the unit for any
considerable length of time, disconnect the plug
from the AC outlet.
Do Not Open the Cabinet
There are no user-serviceable components inside
this product. Opening the cabinet may present a
shock hazard, and any modification to the
product will void your guarantee. If water or any
metal object such as a paper clip, wire or a
staple accidentally falls inside the unit,
disconnect it from the AC power source
immediately, and consult an authorized service
station.
Installation Location
■ To assure proper operation and to avoid the
potential for safety hazards, place the unit on
a firm and level surface. When placing the
unit on a shelf, be certain that the shelf and
any mounting hardware can support the
weight of the product.
■ Make certain that proper space is provided
both above and below the unit for ventilation.
If this product will be installed in a cabinet or
other enclosed area, make certain that there
is sufficient air movement within the cabinet.
Under some circumstances a fan may be
required.
■ Do not place the unit directly on a carpeted
surface.
■ Avoid installation in extremely hot or cold
locations, or an area that is exposed to direct
sunlight or heating equipment.
■ Avoid moist or humid locations.
■ Do not obstruct the ventilation slots on the
top of the unit, or place objects directly over
them.
Cleaning
When the unit gets dirty, wipe it with a clean,
soft, dry cloth. If necessary, wipe it with a soft
cloth dampened with mild soapy water, then a
fresh cloth with clean water. Wipe dry immediately with a dry cloth. NEVER use benzene,
aerosol cleaners, thinner, alcohol or any other
volatile cleaning agent. Do not use abrasive
cleaners, as they may damage the finish of metal
parts. Avoid spraying insecticide near the unit.
Moving the Unit
Before moving the unit, be certain to disconnect
any interconnection cords with other components, and make certain that you disconnect the
unit from the AC outlet.
Unpacking
The carton and shipping materials used to
protect your new receiver during shipment were
specially designed to cushion it from shock and
vibration. We suggest that you save the carton
and packing materials for use in shipping if you
move, or should the unit ever need repair.
To minimize the size of the carton in storage,
you may wish to flatten it. This is done by
carefully slitting the tape seams on the bottom
and collapsing the carton. Other cardboard
inserts may be stored in the same manner.
Packing materials that cannot be collapsed
should be saved along with the carton in a
plastic bag.
If you do not wish to save the packaging
materials, please note that the carton and other
sections of the shipping protection are
recyclable. Please respect the environment and
discard those materials at a local recycling
center.
4 INTRODUCTION / SAFETY INFORMATION
Downloaded from www.Manualslib.com manuals search engine
M
N
R
ENGLISH
Front Panel Controls
Q
AVR 445
2
3
1
7 5 P O G
4
8
9
6 B D
A
C
H
E
J
I K
F
L
1 Main Power Switch
2 System Power Control
3 Power Indicator
4 Headphone Jack
5 Surround Mode Group Selector
6 Speaker Selector
7 ‹ Button
8 Tone Mode
9 Surround Mode Selector
) Tuning Selector
! Tuner Band Selector
@ Set Button
# Preset Station Selector
$ › Button
% Input Source Selector
^ RDS Selector
& Delay Adjust Selector
* Digital Optical 4 Input
( Input/Output Status Indicators
Ó Digital Coax 4 Jack
Ô Video 4 Input/Output Jacks
 Front Panel Control Door
Ò Surround Mode Indicators
Ú Speaker/Channel Input Indicators
Û Digital Select Button
Ù Channel Select Button
ı Volume Control
ˆ Input Indicators
˜ Main Information Display
¯ Remote Sensor Window
˘ EzSet/EQ Microphone Jacks
1 Main Power Switch: Press this button to
apply power to the AVR. When the switch is
pressed in, the unit is placed in a Standby
mode, as indicated by the orange LED 3
surrounding the System Power Control 2.
This button MUST be pressed in to operate the
unit. To turn the unit off completely and prevent
the use of the remote control, this switch
should be pressed until it pops out from the
front panel so that the word “OFF” may be
read at the top of the switch.
NOTE: This switch is normally left in the “ON”
position.
4 Headphone Jack: This jack may be used to
listen to the AVR’s output through a pair of headphones. Be certain that the headphones have a
standard 6.3 mm stereo phone plug. Note that
the main room speakers and all Preamp
Outputs will automatically be turned off
when the headphone jack is in use.
6 Speaker Selector: Press this button to
begin the process of configuring the AVR for the
type of speakers it is being used with. For complete information on configuring the speaker settings using the front-panel controls see page 33.
2 System Power Control: When the Main
Power Switch 1 is “ON,” press this button to
turn on the AVR; press it again to turn the unit
off (to Standby). Note that the Power Indicator
surrounding the switch 3 will turn blue when
the unit is on.
3 Power Indicator: This LED will be
illuminated in orange when the unit is in the
Standby mode to signal that the unit is ready to
be turned on. When the unit is in operation, the
indicator will turn blue.
5 Surround Mode Group Selector: Press this
button to select the top-level group of surround
modes. Each press of the button will select a
major mode grouping in the following order:
Dolby Modes ➜ DTS Digital Modes ➜ DSP
Modes ➜ Stereo Modes ➜ Logic 7 Modes
Once the button is pressed so that the name of
the desired surround mode group appears in the
on-screen display and in the Lower Display Line
˜, press the Surround Mode Selector 9 to
cycle through the individual modes available. For
example, press this button to select Dolby modes,
and then press the Surround Mode Selector
9 to choose from the various mode options.
7 ‹ Button: When an adjustment is being
made using the Channel Select Ù or Digital
Select Û buttons, this button may be pressed
to scroll through the available options.
8 Tone Mode: Pressing this button enables or
disables the Balance, Bass and Treble tone
controls. When the button is pressed so that the
words TONE I N appear in the Main Information Display ˜, the settings of the Bass
and Treble controls and of the Balance control
will affect the output signals. When the button is
pressed so that the words TONE OUT appear
in the Main Information Display ˜, the
output signal will be “flat,” without any balance,
bass or treble alteration, no matter how the
actual Controls are adjusted. (For more information, see page 39).
FRONT PANEL CONTROLS 5
Downloaded from www.Manualslib.com manuals search engine
Front Panel Controls
9 Surround Mode Selector: Press this
button to cycle through the individual surround
modes available after the Surround Mode
Group Selector 5 was pressed (see item 5
above). Note that depending on the type of
input, some modes are not always available. (See
page 36 for more information about surround
modes).
) Tuning Selector: Press the left side of the
button to tune lower frequency stations and the
right side of the button to tune higher frequency
stations. When a station with a strong signal is
reached, MANUAL TUNED or AUTO
TUNED will appear in the Main Information
Display ˜ (see page 49 for more information
on tuning stations).
! Tuner Band Selector: Pressing this button
will automatically switch the AVR to the Tuner
mode. Pressing it again will switch between the
AM and FM frequency bands, holding it pressed
for some seconds will switch between stereo and
mono receiving and between automatic and
manual tuning mode (See page 49 for more
information on the tuner).
@ Set Button: When making choices during
the setup and configuration process, press this
button to enter the desired setting as shown in
the Main Information Display ˜ into the
AVR’s memory.
# Preset Stations Selector: Press this
button to scroll up or down through the list of
stations that have been entered into the preset
memory. (See page 49 for more information on
tuner programming.)
$ › Button: When an adjustment is being
made using the Channel Select Ù or Digital
Select Û buttons, this button may be pressed
to scroll through the available options.
% Input Source Selector: Press this button to
change the input by scrolling through the list of
input sources.
^ RDS Select Button: Press this button to display the various messages that are part of the RDS
data system of the AVR’s tuner. (See page 49 for
more information on RDS).
& Delay Adjust Selector: Press this button to
begin the process of adjusting the delay settings
for Dolby surround modes. See page 33 for more
information on delay adjustments.
* Digital Optical 4 Input: Connect the optical
digital audio output of an audio or video product
to this jack. When the Input is not in use, be
certain to keep the plastic cap installed to avoid
dust contamination that might degrade future
performance.
( Input/Output Status Indicators: These
LED indicators will normally light green to show
that the front panel Video 4 A/V Ô jacks are
operating as an input. When either of these jacks
has been configured for use as an output, the
indicator will turn red to show that the jack may
be used for recording. (See page 43 for more
information on configuring the front panel jacks
as outputs, rather than inputs.)
Ó Digital Coax 4 Jack: This jack is normally
used for connection to the output of portable
audio devices, video game consoles or other
products that have a coax digital jack.
Ô Video 4 Input/Output Jacks: These
audio/video jacks may be used for temporary
connection to video games or portable audio/
video products such as camcorders and portable
audio players. They may also be configured as
output jacks (also S-Video) to feed a signal to
any recording Audio or Video device (see page 43
for more information).
 Front-Panel Control Door: To open the
door so that the front-panel jacks and controls
behind this door may be accessed, gently pull the
door down and towards you using either upper
corner of the door.
Ò Surround Mode Indicators: The current
selected mode or function will appear as one of
these indicators. Note that when the unit is
turned on, the entire list of available modes will
light briefly, and then revert to normal operation
with only the active mode indicator illuminated.
Ú Speaker/Channel Input Indicators: These
indicators are multipurpose, indicating either the
speaker type selected for each channel or the
incoming data-signal configuration. The left, center,
right, right surround and left surround speaker
indicators are composed of three boxes, while the
subwoofer is a single box. The center box lights
when a “Small” speaker is selected, and the two
outer boxes light when “Large” speakers are
selected. When none of the boxes are lit for the
center, surround or subwoofer channels, no speaker
has been selected for that position. (See page 31
for more information on configuring speakers.) The
letters inside each of the center boxes display
active input channels. For standard analog inputs,
only the L and R will light, indicating a stereo
input. When a digital source is playing, the indicators will light to display the channels begin
received at the digital input. When the letters
flash, the digital input has been interrupted. (See
page 42 for more information on the Channel
Indicators).
Û Digital Select Button: When playing a
source that has a digital output, press this button
to select between the Optical * and
Coaxial Ó Digital inputs (See page 41 for
more information).
Ù Channel Select Button: Press this button
to begin the process of trimming the channel
output levels using an external audio source.
(For more information on output level trim
adjustment, see page 44).
ı Volume Control: Turn this knob clockwise
to increase the volume, counterclockwise to
decrease the volume. If the AVR is muted,
adjusting volume control will automatically
release the unit from the silenced condition.
ˆ Input indicators: The current selected
mode or function will appear as one of these
indicators. Note that when the unit is turned on,
the entire list of available modes will light briefly,
and then revert to normal operation with only
the active mode indicator illuminated.
˜ Main Information Display: This display
delivers messages and status indications to help
you operate the receiver.
¯ Remote Sensor Window: The sensor
behind this window receives infrared signals from
the remote control. Aim the remote at this area
and do not block or cover it unless an external
remote sensor is installed.
˘ EzSet/EQ Microphone Jack: Before
starting the EzSet/EQ automated setup process,
plug the microphone into this jack. The
microphone does not need to be plugged in at
other times.
6 FRONT PANEL CONTROLS
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Rear Panel Connections
AM Antenna
FM Antenna
Tape Inputs
Tape Outputs
Main Subwoofer Output
DVD Audio Inputs
CD Inputs
Multiroom Audio Outputs
A-BUS Connector
8-Channel Direct Inputs
Digital Audio Outputs
Video Monitor Outputs
DVD Video Inputs
Front Speaker Outputs
Center Speaker Outputs
Surround Speaker Outputs
Switched AC Accessory Outlet
USB Connector
AC Power Cord Jack
Video 2 Component Video Inputs
Component Video Outputs
Video 1 Component Video Inputs
Remote IR Output
Remote IR Input
Multiroom IR Input
Video 1 Video Outputs
Video 1 Video Inputs
HDMI Output
Video 3 Video Inputs
! Video 2 Video Inputs
Optical Digital Inputs
Coaxial Digital Inputs
" HDMI Inputs
# Video 2 Audio Inputs
$ Video 3 Audio Inputs
% Video 1 Audio Inputs
& Video 1 Audio Outputs
Preamp Outputs
' Surround Back/Multiroom Speaker Outputs
) RS-232 Port
* Fan Vents
+ DVD/Video 3 Component Video Inputs
, Remote IR Carrier Output
- Trigger 1 Output
. The Bridge TheBridge Digital Media Player
(DMP) Input
NOTE: To assist in making the correct connections for multichannel input/output and speaker
connections, all connection jacks and terminals
have been color coded in conformance with the
latest CEA standards as follows:
Front Left:
White
Front Right:
Red
Center:
Green
Surround Left:
Blue
Surround Right:
Gray
Surround Back Left:
Brown
Surround Back Right:
Tan
Subwoofer (LFE):
Purple
Digital Audio:
Orange
Composite Video:
Yellow
Component Video “Y”: Green
Component Video “Pr”: Red
Component Video “Pb”: Blue
AM Antenna: Connect the AM loop antenna
supplied with the receiver to these terminals. If an
external AM antenna is used, make connections to
the AM and GND terminals in accordance with
the instructions supplied with the antenna.
DVD Audio Inputs: Connect these jacks to
the analog audio jacks on a DVD or other audio
or video source.
FM Antenna: Connect the supplied indoor or
an optional external FM antenna to this terminal.
Tape Inputs: Connect these jacks to the
PLAY/OUT jacks of an audio recorder.
Tape Outputs: Connect these jacks to the
RECORD/INPUT jacks of an audio recorder.
Main Subwoofer Output: Connect this
jack to the line-level input of a powered
subwoofer. If an external subwoofer amplifier is
used, connect this jack to the subwoofer
amplifier input. If only one subwoofer is used in
your system, connect it here.
TM
CD Inputs: Connect these jacks to the
analog output of a compact disc player or CD
changer or any other audio source.
Multiroom Audio Outputs: Connect these
jacks to an optional audio power amplifier to
listen to the source selected by the multiroom
system in a remote room.
A-BUS Connector: Connect this jack to an
optional A-BUS-certified remote room keypad or
amplifier to extend the multiroom capabilities of
your AVR. See page 20 for more information on
A-BUS.
REAR PANEL CONNECTIONS 7
Downloaded from www.Manualslib.com manuals search engine
Rear Panel Connections
8-Channel Direct Inputs: These jacks are
used for connection to source devices such as
DVD-Audio or SACD players with discrete analog
outputs. Depending on the source device in use,
all eight jacks may be used, though in many
cases only connections to the front left/right,
center, surround left/right and LFE (subwoofer
input) jacks will be used for standard 5.1 audio
signals.
Digital Audio Outputs: Connect these
jacks to the matching digital input connector on
a digital recorder such as a CD-R or MiniDisc
recorder.
Video Monitor Outputs: Connect this jack
to the composite and/or S-Video input of a TV
monitor or video projector to view the on-screen
menus and the output of any standard Video or
S-Video source selected by the receiver’s video
switcher.
DVD Video Inputs: Connect these jacks to
the composite or S-Video output jacks on a DVD
player or other video source.
Front Speaker Outputs: Connect these
outputs to the matching + or – terminals on your
left and right speakers. In conformance with the
new CEA color code specification, the White terminal is the positive, or "+" terminal that should
be connected to the red (+) terminal on Front
Left speaker with the older color coding, while
the Red terminal is the positive, or "+" terminal
that should be connected to the red (+) terminal
on Front Right speaker. Connect the black (–)
terminals on the AVR to the black (–) terminals
on the speakers. See page 16 for more
information on speaker polarity.
Center Speaker Outputs: Connect these
outputs to the matching + and – terminals on
your center channel speaker. In conformance with
the new CEA color code specification, the Green
Terminal is the positive, or "+" terminal that
should be connected to the red (+) terminal on
speakers with the older color coding. Connect
the black (–) terminal on the AVR to the black
negative (–) terminal on your speaker. (See page
16 for more information on speaker polarity.)
Surround Speaker Outputs: Connect
these outputs to the matching + and – terminals
on your surround channel speakers. In conformance with the new CEA color code specification, the Blue terminal is the positive, or "+"
terminal that should be connected to the red (+)
terminal on the Surround Left speaker with older
color coding, while the Gray terminal should be
connected to the red (+) terminal on the
Surround Right speaker with the older color
coding. Connect the black (–) terminal on the
AVR to the matching black negative (–) terminals
for each surround speaker. (See page 16 for more
information on speaker polarity.)
Switched AC Accessory Outlet: This outlet
may be used to power any device that you wish
to have turn on when the AVR is turned on with
the System Power Control switch 2.
USB Connector: Connect a cable with a
USB “Mini B” connector to the AVR and the
other end to a compatible computer running
Windows® 2000, Windows® XP or higher with
the latest service packs installed, to use this port
to listen to audio from the computer through the
AVR 445. This connection is also used to connect
a compatible computer to the AVR for firmware
upgrades, when available. See page 41 for more
information on playback of computer audio with
the AVR. Instructions for upgrades will accompany the upgrade file download package.
AC Power Cord Jack: Connect the AC
power cord to this jack when the installation is
complete. To ensure safe operation, use only the
power cord supplied with the unit. If a replacement is required it must be of the same type and
capacity.
Component Video 2 Inputs: These inputs
may be used with any video source device
equipped with analog Y/Pr/Pb or RGB component
video outputs. The factory default is for these
jacks to be a linked to the Video 2 input, but you
may change the setting at any time through the
IN/OUT SETUP menu. See page 16 for
more information on configuring the component
video inputs.
Monitor Component Video Outputs:
Connect these outputs to the component video
inputs of a video projector or monitor. When a
source connected to one of the two
Component Video Inputs is selected the
signal will be sent to these jacks.
8 REAR PANEL CONNECTIONS
Downloaded from www.Manualslib.com manuals search engine
Component Video 1 Inputs: These inputs
may be used with any source device equipped
with analog Y/Pr/Pb or RGB component video
outputs. The factory default is for these jacks to
be a linked to the Video 1 input, but you may
change the setting at any time through the
IN/OUT SETUP menu. See page 16 for
more information on configuring the component
video inputs.
Note: All component inputs/outputs can be used
for RGB signals too, in the same way as
described for the Y/Pr/Pb signals, then connected
to the jacks with the corresponding color.
RGB connection is not possible if the source outputs a separate sync signal.
Remote IR Output: This connection permits
the IR sensor in the receiver to serve other
remote controlled devices. Connect this jack to
the “IR IN” jack on Harman Kardon or other
compatible equipment.
Remote IR Input: If the AVR’s front-panel
IR sensor is blocked due to cabinet doors or
other obstructions, an external IR sensor may be
used. Connect the output of the sensor to this
jack.
Multiroom IR Input: Connect the output of an
IR sensor in a remote room to this jack to operate
the AVR’s multiroom control system.
Video 1 Video Outputs: Connect these
jacks to the RECORD/INPUT composite or
S-Video jack on a VCR.
Video 1 Video Inputs: Connect these jacks
to the PLAY/OUT composite or S-Video jacks on
a VCR or other video source.
HDMI Output: Connect this jack to the
HDMI input on a compatible HDMI-equipped
video display.
Video 3 Video Inputs: Connect these jacks
to the PLAY/OUT composite or S-Video jacks on
any video source.
! Video 2 Video Inputs: Connect these jacks
to the PLAY/OUT composite or S-Video jacks on
a second VCR or other video source.
Optical Digital Inputs: Connect the
optical digital output from a DVD player, HDTV
receiver, LD player, MD player or CD player to
these jacks. The signal may be either a Dolby
Digital signal, a DTS signal, a 2 channel MPEG 1
signal or a standard PCM digital source.
Coaxial Digital Inputs: Connect the coax
digital output from a DVD player, HDTV receiver,
LD player, MD player or CD player to these jacks.
The signal may be either a Dolby Digital signal,
DTS signal, a 2 channel MPEG 1 signal or a
standard PCM digital source. Do not connect the
RF digital output of an LD player to these jacks.
" HDMI Inputs: Connect the HDMI output of
video sources such as a DVD player, set-top box
or HDTV tuner to either of these jacks.
# Video 2 Audio Inputs: Connect these jacks
to the PLAY/OUT audio jacks on a second VCR
or other audio or video source.
$ Video 3 Audio Inputs: Connect these jacks
to the PLAY/OUT audio jacks on any audio or
video source.
% Video 1 Audio Inputs: Connect these jacks
to the PLAY/OUT audio jacks on a VCR or other
audio or video source.
& Video 1 Audio Outputs: Connect these
jacks to the RECORD/INPUT audio jacks on
a VCR or any other Audio recorder.
Preamp Outputs: Connect these jacks to an
optional, external power amplifier for
applications where higher power is desired.
' Surround Back/Multiroom Speaker
Outputs: These speaker terminals are normally
used to power the surround back left/surround
back right speakers in a 7.1 channel system.
However, they may also be used to power the
speakers in a second zone, which will receive the
output selected for a multiroom system.
To change the output fed to these terminals from
the default of the Surround Back speakers to the
Multiroom Output, you must change a setting in
the Multiroom Menu of the OSD system. See
page 47 for more information on configuring this
speaker output. In normal surround system use,
the brown and black terminals are the surround
back left channel positive (+) and negative (–)
connections and the tan and black terminals are
the surround back right positive (+) and negative
(–) terminals.
For multiroom use, connect the brown and black
SBL terminals to the red and black connections
on the left remote zone speaker and connect the
tan and black SBR terminals to the red and black
terminals on the right remote zone speaker.
) RS-232 Port: This jack may be used to
control the AVR 445 over a bi-directional RS-232
serial control link to a compatible computer or
programmable remote control system. Due to the
complexity of programming RS-232 commands
we strongly recommend that connections to this
port for control purposes be made by a trained
and qualified technician. This jack may also link
to a compatible computer to upgrade the
software and operating system of the AVR 445
when appropriate upgrades are available.
* Fan Vents: These ventilation holes are the
output of the AVR’s airflow system. To ensure
proper operation of the unit and to avoid
possible damage to delicate surfaces, make
certain that these holes are not blocked and that
there is at least three inches of open space
between the vent holes and any wooden or
fabric surface.
.
Digital Media Player (DMP)
Connector: With the AVR 445 turned off,
connect one end of the optional Harman Kardon
to this proprietary connector, and the
other to your compatible Apple iPod. When the
Digital Media Player source is selected, you may
view your iPod’s control and navigation
messages on your video display (if one is
connected to one of the Video Monitor
Outputs ), and in the Upper and Lower
Display Lines ˜. You may navigate the iPod
and select tracks for playback using the
⁄¤‹ › Buttons EF, the Set Button
FQ and Transport Controls PP on
your AVR remote. See page 43 for more
information.
+ DVD/Video 3 Component Video Inputs:
These inputs may be used with any source device
equipped with analog Y/Pr/Pb or RGB component
video outputs. The factory default is for these
jacks to be a linked to the DVD input, but you
may change the setting at any time through the
IN/OUT SETUP menu. See page 17 for
more information on configuring the component
video inputs.
, Remote IR Carrier Output: The output of
this jack is the full signal received at the
Remote Sensor Window ¯ or input through
the Remote IR Input including the carrier
frequency that is removed from signals at the
Remote IR Output . Use this output to
extend IR remote signals to the input of
compatible products by direct connection or
through the use of optional, external IR
“blasters”. If you are in doubt as to which of the
two IR Output jacks to use, we recommend that
you consult with your dealer or installer, or check
with the manufacturer of the external equipment
you wish to control.
- Trigger 1 Output: Connect this jack to the
“Trigger In” jack of an optional external
component such as an audio power amplifier
that you want to be controlled to mirror the
power state of the AVR 445. When this
connection is used, the AVR 445 will automatically send a low-voltage signal to the connected
device that turns it on when the AVR 445 is on
and off when the AVR 445 is placed in the
Standby Mode. The connected component must
respond to 6-volt presence as the control signal.
REAR PANEL CONNECTIONS 9
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Rear Panel Connections
Main Remote Control Functions
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Power Off Button
IR Transmitter Window
LCD Information Display
Power On Button
Input Selectors
AVR Selector
AM/FM Tuner Select
6-Channel/8-Channel Direct Input
Test Button
Sleep Button
Surround Mode Selector
Night Mode
Channel Select Button
Dim Button
Navigation Button
Set Button
Digital Select
Numeric Keys
Tuner Mode
Direct Button
Tuning Up/Down
OSD Button
Dolby Mode Select Button
DTS Digital Mode Selector
Logic 7 Mode Select Button
Transport Controls
Light Button
Skip Up/Down Buttons
Stereo Mode Select Button
DTS Neo:6 Mode Select
Macro Buttons
Disc Skip Button
Preset Up/Down
Clear Button
Memory Button
Delay/Prev. Ch.
Program Button
Speaker Select
Multiroom
Volume Up/Down
EzSet/EQ On/Off Button
Channel Up/Down Selector
Mute
Tone Control Button
NOTE: The function names shown here are each
button’s feature when used with the AVR. Most
buttons have additional functions when used
with other devices.
The jack on the upper right side of the remote is
reserved for future use. Do not remove the plug
provided or connect any device to the jack.
10 MAIN REMOTE CONTROL FUNCTIONS
Downloaded from www.Manualslib.com manuals search engine
3
0
1
2
4
5
8
A
O
J
I
7
M
N
H
C
E
F
G
P
P
P
Q
K
6
D
L
B
9
IMPORTANT NOTE: The AVR 445’s remote may
be programmed to control up to seven devices,
including the AVR. Before using the remote, it is
important to remember to press the Input
Selector button 4 that corresponds to the
unit you wish to operate. In addition, the AVR’s
remote is shipped from the factory to operate the
AVR and most Harman Kardon CD or DVD players
and cassette decks. The remote is also capable of
operating a wide variety of other products using
the control codes that are part of the remote or
by learning commands from other remotes. Before
using the remote with other products, follow the
instructions on pages 51-52 to program the proper codes for the products in your system.
It is also important to remember that many of
the buttons on the remote take on different
functions, depending on the product selected
using the Input Selector Button 4. The
descriptions shown here primarily detail the functions of the remote when it is used to operate
the AVR.
0 Power Off Button: Press this button to
place the AVR or a selected device unit in the
Standby mode. Note that when the AVR is
switched off this will turn off the main room
functions, but if the Multiroom system is activated,
it will continue to function.
1 IR Transmitter Window: Point this window
towards the AVR when pressing buttons on the
remote to make certain that infrared commands
are properly received.
2 LCD Information Display: This two-line
screen displays various information depending on
the commands that have been entered into the
remote.
3 Power On Button: Press this button to turn
on the power to a device selected by pressing one
of the Input Selectors 4 (except Tape).
4 Input Selectors: Pressing one of these
buttons will perform three actions at the same
time. First, if the AVR is not turned on, this will
power up the unit. Next, it will select the source
shown on the button as the input to the AVR.
Finally, it will change the remote control so that
it controls the device selected.
The buttons labeled DVD, DMP and HDMI 1 are
each used to select either of two input sources:
• The first press of the DVD Button selects the
component connected to the DVD inputs. A second press of this button selects the component
connected to the CD inputs.
• The first press of the button labeled DMP
selects The Bridge as the input. A second press of
this button selects the device connected to the
Tape inputs.
• The first press of the HDMI 1 button selects the
device that is connected to the HDMI 1 jack.
A second press selects the device connected to
the HDMI 2 jack.
In normal operation, the remote will revert to
controlling the AVR when no button is pressed
for 6 seconds. This allows the remote to
automatically return to control of important
functions such as volume, mute and surround
mode selection after you have used the remote
to control another device. If you wish to change
the length of time that the remote operates
another device, or to have the remote remain
active for control of the other device (such as a
DVD player or set-top box) until you manually
return control to the AVR by pressing the AVR
Selector 5, follow the instructions on page
38.
5 AVR Selector: Pressing this button will
switch the remote so that it will operate the AVR’s
functions. If the AVR is in the Standby mode, it will
also turn the AVR on.
6 AM/FM Tuner Select: Press this button to
select the AVR’s tuner as the listening choice.
Pressing this button when the tuner is in use will
select between the AM and FM bands.
7 6-Channel/8 Channel Direct Input:
Press this button to select the device connected
to the 6-Channel Direct Inputs or the
8-Channel Direct Inputs (the input
available will depend on the selection 5.1 or
6.1/7.1 made in the surround mode setting,
see page 26 for more information).
8 Test Tone: Press this button to begin the
sequence used to calibrate the AVR’s output levels.
(See page 34 for more information on calibrating
the AVR.)
9 Sleep Button: Press this button to place
the unit in the Sleep mode. After the time shown
in the display, the AVR will automatically go into
the Standby mode. Each press of the button
changes the time until turn-off in the following
order:
90
min
80
min
70
min
60
min
50
min
40
min
30
min
20
min
10
min
OFF
Hold the button pressed for two seconds to turn
off the Sleep mode setting.
Note that this button is also used to change
channels on your TV, VCR and Sat receiver when
the appropriate source is selected, using the
device Input Selectors 4.
A Surround Mode Selector: Press this button to select any of the HALL, THEATER surround
modes. Note that depending on the type of
input, some modes are not always available. (See
page 36 for more information about surround
modes.) Note that this button is also used to
tune channels on your TV, VCR and Sat receiver
when the appropriate source is selected using
the device Input Selector 4.
B Night Mode: Press this button to activate
the Night mode. This mode is available only with
Dolby Digital encoded sources, and it preserves
dialog (center channel) intelligibilty at low volume levels (See page 27 for more information).
C Channel Select Button: This button is
used to start the process of setting the AVR’s
output levels with an external source. Once this
button is pressed, use the ⁄/¤ buttons E to
select the channel being adjusted, then press the
Set button F, followed by the ⁄/¤ buttons
E again, to change the level setting. (See page
34 for more information.)
D Dim Button: Press this button to activate
the Dimmer function, which reduces the brightness of the front-panel display, or turns it off
entirely. Press the button once to change the
display to reduce the brightness by 50%, and
press it again within five seconds and the main
display will go completely dark. Note that this
setting is temporary; regardless of any changes,
the display will always return to full brightness
when the AVR is turned on. The blue illumination
around the Standby/On Button 1 will always
remain at full brightness regardless of the setting
to remind you that the AVR is still turned on. The
blue accent lighting inside the volume control
will also remain at full brightness when the panel
is at 50%, but go out when the panel lights are
fully dimmed.
MAIN REMOTE CONTROL FUNCTIONS 11
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Main Remote Control Functions
Main Remote Control Functions
E Navigation Button: This single disc-like
button is used to change or scroll through items
in the on-screen menus or on the front panel or
to make configuration settings such as digital
inputs or delay timing. When changing a setting,
first press the button for the function or setting
to be changed (e.g., press the Digital Select
Button G to change a digital input) and then
press one of these buttons to scroll through the
list of options or to increase or decrease a setting. The sections in this manual describing the
individual features and functions contain specific
information on using these buttons for each
application.
F Set Button: This button is used to enter
settings into the AVR’s memory. It is also used in
the setup procedures for delay time, speaker
configuration and channel output level
adjustment.
G Digital Select: Press this button to assign
one of the digital inputs *Ó to a source.
(See page 41 for more information on using
digital inputs.)
H Numeric Keys: These buttons serve as a
ten-button numeric keypad to enter tuner preset
positions. They are also used to select channel
numbers when TV, VCR or Sat receiver has been
selected on the remote, or to select track
numbers on a CD, DVD or LD player, depending
on how the remote has been programmed.
I Tuner Mode: Press this button when the
tuner is in use to select between automatic
tuning and manual tuning. When the button is
pressed so MANUAL appears in the Main
Information Display ˜, pressing the Tuning
buttons K) will move the frequency up or
down in single-step increments. When the FM
band is in use and AUTO appears in the Main
Information Display ˜, pressing this button
will change to monaural reception making even
week stations audible. (See page 49 for more
information.)
J Direct Button: Press this button when the
tuner is in use to start the sequence for direct
entry of a station’s frequency. After pressing the
button simply press the proper Numeric Keys
H to select a station (See page 49 for more
information on the tuner).
12 MAIN REMOTE CONTROL FUNCTIONS
Downloaded from www.Manualslib.com manuals search engine
K Tuning Up/Down: When the tuner is in use,
these buttons will tune up or down through the
selected frequency band. If the Tuner Mode
button I has been pressed or the Band button
! on the front panel was held pressed so that
AUTO appears in the Main Information
Display ˜, pressing either of the buttons will
cause the tuner to seek the next station with
acceptable signal strength for quality reception.
When the MANUAL appears in the Main
Information Display ˜, pressing these
buttons will tune stations in single-step
increments. (See page 50 for more information.)
L OSD Button: Press this button to activate
the On Screen Display (OSD) system used to set
up or adjust the AVR’s parameters.
M Dolby Mode Selector: This button is used
to select one of the available Dolby Surround
processing modes. Each press of this button will
select one of the Dolby Pro Logic II modes, Dolby
3 Stereo or Dolby Digital. Note that the Dolby
Digital mode is only available with a digital input
selected and the other modes only as long as a
Dolby Digital source is not playing (except
Pro Logic II with Dolby Digital 2.0 recordings, see
Note on page 40). See page 27 for the available
Dolby surround mode options.
N DTS Digital Mode Selector: When a DTS
source is in use the AVR will select the
appropriate mode automatically and no other
mode will be available. Pressing this button will
display the mode currently selected by the AVR´s
decoder, depending on the surround material
played and the speaker setting (see item 6,
page 5). When a DTS source is not in use, this
button has no function. (See page 27, 32 for the
available DTS options.)
O Logic 7 Selector: Press this button to
select one of the available Logic 7 surround
modes. (See page 36 for the available Logic 7
options.)
P Transport Control Buttons: These buttons
do not have any functions for the AVR, but they
may be programmed for the forward/reverse play
operation of a wide variety of CD or DVD players,
and audio or video- cassette recorders. (See page
51 for more information on programming the
remote.)
Q Light Button: Press this button to activate
the remote’s built-in backlight for better legibility
of the buttons in a darkened room.
Skip Up/Down Buttons: These buttons do
not have a direct function with the AVR, but
when used with a compatibly programmed CD or
DVD player/changer they will change the tracks
on the disc currently being played.
Stereo Mode Selector: Press this button
to select a stereo playback mode. When the
button is pressed so that DSP SURR OFF
appears in the Main Information Display ˜,
the AVR will operate in a bypass mode with true
fully analog, two-channel left/right stereo mode
with no surround processing or bass
management as opposed to other modes where
digital processing is used. When the button is
pressed so that SURROUND OFF appears in
the Main Information Display ˜, you may
enjoy a two-channel presentation of the sound
along with the benefits of bass management.
When the button is pressed so that 5 C H
STEREO or 7 C H STEREO appears, the
stereo signal is routed to all five speakers, if
installed. (See page 40 for more information on
stereo playback modes).
DTS Neo:6 Mode Selector: Pressing this
selector button cycles the AVR through the
various DTS Neo:6 modes, which extract a fiveor seven-channel surround field from two-channel program material (from PCM source or
analog input signal). The first press selects the
last DTS Neo:6 surround mode that was in use,
and each subsequent press selects the next
mode in the following order:
DTS Neo:6 MUSIC
DTS Neo:6
MOVIES
Macro Buttons: Press these buttons to
store or recall a “Macro”, which is a pre-programmed sequence of commands stored in the
remote. (See page 54 for more information on
storing and recalling macros.)
Disc Skip Button: This button has no
direct function for the AVR but may be used to
change the disc in a CD or DVD changer when
the remote is programmed for that type of
device.
Preset Up/Down: When the tuner is in
use, press these buttons to scroll through the
stations programmed into the AVR’s memory.
When CD or DVD is selected using the Input
Selector button 4, these buttons may function as Slow Fwd/Rev (DVD) or ”+10” (CD, CDR).
Clear Button: Press this button to clear
incorrect entries when using the remote to directly
enter a radio station’s frequency.
Memory Button: Press this button to enter
a radio station into the AVR’s preset memory. Two
underline indicators will flash at the right side of
the Main Information Display ˜, you then
have five seconds to enter a preset memory
location using the Numeric Keys H. (See
page 49 for more information.)
Delay Select Button: This button selects
adjustments to the A/V Sync Delay and the
individual channel displays. The first press of the
button displays an A/V SYNC DELAY
message in the Lower Display Line ˜ and in
the on-screen display, which means that you may
change the amount of time that all channels are
delayed together behind the video. This enables
you to compensate for the loss of lip sync that
may be caused by digital video processing in your
display or by television stations. To change the
A/V Sync Delay, press the Set Button F while
the A/V SYNC DELAY message is visible
and then use the ⁄/¤ Navigation Button E
to change the setting so that the sound and the
video image are in sync. To change the delay for
an individual output channel, press the ⁄/¤
Navigation Button E until the desired
channel name is shown, and then press the Set
Button F. Use the ⁄/¤ Navigation
Buttons E to change the delay amount. (See
page 33 for more information on delay options.)
Program Button: This button is used to
begin the process of programming the remote.
Press and hold this button for three seconds to
place the remote in the programming mode.
Once the red LED under the Set Button F
lights, release the button. You may then select
from the desired option. (See pages 51-59 for
more information on configuring the remote.)
ENGLISH
Main Remote Control Functions
Speaker Select: Press this button to begin
the process of configuring the AVR’s Bass
Management System for use with the type of
speakers used in your system. Once the button
has been pressed, use the ⁄/¤ buttons E to
select the channel you wish to set up. Press the
Set Button F and then select the speaker
type (Large, Small or None) appropriate with the
speaker in use. (See page 21 for more
information.)
Multi-Room: Press this button to activate
the Multiroom system or to begin the process of
changing the input or volume level for the
second zone. (See page 47 for more information
on the Multiroom system.)
Volume Up/Down: Press these buttons to
raise or lower the system volume.
EzSet/EQ Button: Press this button to turn
the filters used by EzSet/EQ on or off. This allows
you to hear the difference in system performance
when EzSet/EQ is engaged or out of the signal
path.
Channel Up/Down Selector: This button
has no function when the AVR is being
controlled, but when programmed for use with a
VCR, TV, cable box, satellite receiver or other
similar product it will change the channel up or
down. See pages 51-59 for more information on
programming the remote.
Mute: Press this button to momentarily
silence the AVR or TV set being controlled,
depending on which device has been selected.
When the AVR remote is being programmed to
operate another device, this button is pressed with
the Input Selector button 4 to begin the
programming process. (See page 51 for more
information on programming the remote.)
Tone Control Button: This button controls
the tone mode settings, enabling adjustment of
the bass and treble boost/cut. You may also use
it to take the tone controls out of the signal path
completely for “flat” response. The first press of
the button displays a TONE I N message in the
Lower Display Line ˜ and in the on-screen
display. To take the controls out of the signal
path press either of the ⁄/¤ Navigation
Buttons E until the display reads TONE
OUT. To change the bass or treble settings,
press the button again until the desired option
appears in the Lower Display Line ˜ and in
the on-screen display and then press either of
the ⁄/¤ Navigation Buttons E to enter the
desired boost or cut setting. See page 25 for
more information on the tone controls.
MAIN REMOTE CONTROL FUNCTIONS 13
Downloaded from www.Manualslib.com manuals search engine
Zone II Remote Control Functions
A
K
E
J
B
D
C
J
We strongly recommend that the ZR 10 remote
be used for the initial configuration and setup
process for the AVR 445.
A Power Off: When used in the room where
the AVR is located, press this button to place the
unit in Standby. When it is used in a remote room
with a sensor that is connected to the Multi IR
jack , this button turns the Multi-Room system
off.
B AVR Selector: Press this button to turn on
the AVR. The input in use when the unit was last
on will be selected.
Q
C AM/FM Tuner Select: Press this button to
select the Tuner as the input to the Multiroom
system. Press it again to change between the AM
and FM bands.
P
D Input Selectors: When the AVR is off,
press one of these buttons to turn the unit on
and to select a specific input. When the unit is
already in use, pressing one of these buttons will
change the input.
F
I
The Zone II remote may be used in either the
same room where the AVR is located, or it may
be used in a separate room with an optional
infrared sensor that is connected to the AVR’s
Multi IR input jack .
H
E OSD Button: Press this button to activate
the On Screen Display (OSD) system used to set
up or adjust the AVR’s parameters.
O
G
N
M
L
J
A
B
C
D
E
F
G
H
I
J
K
L
M
Power Off
AVR Selector
AM/FM Tuner Select
Input Selectors
OSD Button
Navigation Controls
Numeric Keys
Disc Skip
Volume Up/Down
Blank Buttons
Mute
Clear Button
Direct Button
14 ZONE II REMOTE CONTROL FUNCTIONS
Downloaded from www.Manualslib.com manuals search engine
N
O
P
Q
Memory Button
Tuner Mode Button
Transport Controls
Set Button
The Bridge
/DMP Selector
NOTE: The Zone II remote may be used in either
the same room where the AVR is located, or it
may be used in a separate room with an
optional infrared sensor that is connected to the
AVR’s Multi IR input jack f. When it is used in
the same room as the AVR, it will control the
F Navigation Controls: Depending on the
menu or function in use, pressing these buttons
will navigate through menus, scroll through
option lists or configuration choices, or move the
cursor position. Press the left, right, up or down
button, as appropriate to the adjustment being
made.
functions of the AVR or any compatible
Harman Kardon products in that room. When it
is used in a separate room via a sensor
connected to the Multi IR Jack f, the buttons
for power, input source, volume and mute will
control the source and volume for the second
zone, as connected to the Multi Out Jacks •.
(See page 47 for complete information on using
the Multiroom system.)
G Numeric Keys: These buttons serve as a
ten-button numeric keypad to enter tuner preset
positions. They are also used to select channel
numbers when TV, VCR or Sat receiver has been
selected on the remote, or to select track
numbers on a CD, DVD or LD player, depending
on how the remote has been programmed.
N Memory Button: Press this button to enter
a radio station into the AVR’s preset memory. Two
underline indicators will flash at the right side of
the Main Information Display ˜, you then
have five seconds to enter a preset memory
location using the Numeric Keys G. (See
page 49 for more information.)
H Disc Skip: Press this button to change discs
on compatible Harman Kardon CD or DVD
changers.
O Tuner Mode: Press this button when the
tuner is in use to select between automatic
tuning and manual tuning. When the button is
pressed so MANUAL appears in the Main
Information Display ˜, pressing the Tuning
buttons K will move the frequency up or down
in single-step increments. When the FM band is
in use and AUTO appears in the Main
Information Display ˜, pressing this button
will change to monaural reception making even
week stations audible. (See page 49 for more
information.)
I Volume Up/Down: When used in the room
where the AVR is located, press this button to
raise or lower the volume in that room. When it
is used in a remote room with a sensor that is
connected to the Multi IR Jack , this button
will raise or lower the volume in the remote
room.
J Blank Buttons: These buttons are not
active. Pressing them will not change or control
any function on the AVR 445 or other IR devices.
K Mute: When used in the room where the
AVR is located, press this button to temporarily
silence the unit. When it is used in a remote
room with a sensor that is connected to the
Multi IR Jack , this button will temporarily
silence the feed to the remote room only. Press
the button again to return to the previous
volume level.
Important Note: No matter in which room the
Zone II remote is used, as with the main remote
it is important to remember to press the Input
Selector button D that corresponds to the
unit you wish to operate befor you change the
device to be controlled.
L Clear Button: Press this button to clear
incorrect entries when using the remote to directly
enter a radio station’s frequency.
M Direct Button: Press this button when the
tuner is in use to start the sequence for direct
entry of a station’s frequency. After pressing the
button simply press the proper Numeric Keys
G to select a station (See page 49 for more
information on the tuner).
ENGLISH
Zone II Remote Control Functions
P Transport Control Buttons: These buttons
do not have any functions for the AVR, but they
are programmed for the forward/reverse play
operation of a wide variety of Harman Kardon
CD or DVD players, and audio- or video-cassette
recorders.
Q Set Button: This button is used to enter
settings into the AVR’s memory. It is also used in
the setup procedures for delay time, speaker
configuration and channel output level
adjustment.
Digital Media Player (DMP)
Selector: When Harman Kardon’s
(optional) is connected to
Digital
Media Player (DMP) Connector . and a
compatible Apple® iPod® is docked in
,
pressing this selector will select the iPod as the
audio source input device for the AVR 445. In
addition, if a video display is connected to one of
the Video Monitor Outputs , the iPod’s
messages will appear on screen, and in the
Upper and Lower Display Lines ˜. The
⁄/¤/‹/› Buttons EF, the Set Button
FQ and the Transport Controls PP
may be used to navigate the iPod and to operate
many functions. See page 43, and the manuals
for The Bridge and your iPod for more
information.
ZONE II REMOTE CONTROL FUNCTIONS 15
Downloaded from www.Manualslib.com manuals search engine
Installation and Connections
After unpacking the unit, and placing it on a solid
surface capable of supporting its weight, you will
need to make the connections to your audio and
video equipment.
5. Assemble the AM Loop Antenna supplied with
the unit as shown below. Connect it to the AM
and GND screw terminals .
Audio Equipment Connections
We recommend that you use high-quality
interconnect cables when making connections to
source equipment and recorders to preserve the
integrity of the signals.
When making connections to audio source
equipment or speakers it is always a good
practice to unplug the unit from the AC wall
outlet. This prevents any possibility of
accidentally sending audio or transient signals to
the speakers that may damage them.
1. Connect the analog output of a CD player to
the CD inputs .
NOTE: When the CD player has both fixed and
variable audio outputs it is best to use the fixed
output unless you find that the input to the
receiver is so low that the sound is noisy, or so
high that the signal is distorted.
2. Connect the analog Play/Out jacks of a
cassette deck, MD, CD-R or other audio recorder
to the Tape Input jacks . Connect the analog
Record/In jacks on the recorder to the Tape
Output jacks on the AVR.
3. Connect the digital output of any digital
sources such as a CD or DVD changer or player,
advanced video game, a digital satellite receiver,
HDTV tuner or digital cable set-top box or the
output of a compatible computer sound card to
the Optical and Coaxial Digital Inputs
*Ó.
4. Connect the Coaxial or Optical Digital
Outputs on the rear panel of the AVR to the
matching digital input connections on a CD-R or
MiniDisc recorder.
6. Connect the supplied FM antenna to the FM
(75 ohm) connection . The FM antenna may
be an external roof antenna, an inside powered
or wire lead antenna or a connection from a
cable system. Note that if the antenna or
connection uses 300-ohm twin-lead cable, you
should use a 300-ohm-to-75-ohm adapter to
make the connection.
7. Connect the front, center and surround
speaker outputs ' to the respective
speakers.
To ensure that all the audio signals are carried to
your speakers without loss of clarity or
resolution, we suggest that you use high-quality
speaker cable. Many brands of cable are
available and the choice of cable may be
influenced by the distance between your
speakers and the receiver, the type of speakers
you use, personal preferences and other factors.
Your dealer or installer is a valuable resource to
consult in selecting the proper cable.
Regardless of the brand of cable selected, we
recommend that you use a cable constructed of
fine, multistrand copper with an area greater than
2 mm2.
Cable with an area of 1.5 mm2 may be used for
short runs of less than 4 m. We do not
recommend that you use cables with an area less
than 1 mm2 due to the power loss and
degradation in performance that will occur.
Cables that are run inside walls should have the
appropriate markings to indicate listing with any
appropriate testing agency standards. Questions
about running cables inside walls should be
referred to your installer or a licensed electrician
who is familiar with the applicable local building
codes in your area.
When connecting wires to the speakers, be
certain to observe proper polarity. Note that the
positive (+) terminal of each speaker connection
now carries a specific color code as noted on
page 7. However, most speakers will still use a
red terminal for the postive (+) connection.
Connect the “negative” or “black” wire to the
same terminal on both the receiver and the
speaker.
16 INSTALLATION AND CONNECTIONS
Downloaded from www.Manualslib.com manuals search engine
NOTE: While most speaker manufacturers
adhere to an industry convention of using black
terminals for negative and red ones for positive,
some manufacturers may vary from this
configuration. To assure proper phase and
optimal performance, consult the identification
plate on your speaker or the speaker’s manual to
verify polarity. If you do not know the polarity of
your speaker, ask your dealer for advice before
proceeding, or consult the speaker’s
manufacturer.
We also recommend that the length of cable
used to connect speaker pairs be identical. For
example, use the same length piece of cable to
connect the front-left and front-right or
surround-left and surround-right speakers, even
if the speakers are a different distance from the
AVR.
8. Connections to a subwoofer are normally
made via a line level audio connection from the
Subwoofer Output to the line-level input
of a subwoofer with a built-in amplifier. When a
passive subwoofer is used, the connection first
goes to a power amplifier, which will be
connected to one or more subwoofer speakers.
If you are using a powered subwoofer that does
not have line-level input connections, follow the
instructions furnished with the speaker for
connection information.
9. If an external multi-channel audio source with
5.1 or 7.1 outputs such as an external digital
processor/decoder, DVD-Audio or SACD player is
used, connect the outputs of that device to the
8-Channel Direct Inputs .
Analog Video Equipment
Connections
Analog video equipment is connected in the same
manner as audio components. Again, the use of
high-quality interconnect cables is recommended
to preserve signal quality.
1. Connect a VCR’s audio and video Play/Out
jacks to the Video 1 or Video 2 In jacks !
# % on the rear panel. The Audio and Video
Record/In jacks on the VCR should be connected
to the Video 1 Out jacks & on the AVR.
2. Connect the analog audio and video outputs
of a satellite receiver, cable TV converter or television set or any other video source to the Video 3
$ jacks.
3. Connect the analog audio and video outputs
of a DVD or laser disc player to the DVD jacks
.
4. If any of the video source devices has analog
component video (Y/Pr/Pb) outputs, but not
HDMI, connect them to Component Video
Inputs . The chart on page 62 has the
default settings for various source devices, but
you may make any connection and change the
configuration setting using the IN/OUT
SETUP menu, as described on page 24.
5. The default video connection for a DVD player
is to use the Component Video Input 3 Jacks
+ on the AVR, but you may change this
assignment in the IN/OUT SETUP menu
(see page 24). A DVD player’s composite and
S-video outputs may also be connected to the
DVD Video Inputs .
6. The default audio connection for a DVD player
is to link the coaxial digital audio output on the
DVD player to the Coaxial 1 Digital Audio
Input , but you may also make a connection
to either the Coaxial or Optical digital
inputs, or the Analog DVD Audio Inputs .
You may change the assignment in the
IN/OUT SETUP menu as described on page
24, or by using the front-panel Digital Input
Selector Û.
7. If you wish to use a portable audio/video
product such as a camcorder, portable media
player or digital still camera with the AVR, or
make a connection to a video game console or
other source that may not always be connected
to the AVR, connect the video outputs of the
source to the Video 4 Input/Output Jacks Ô
that are behind the Front-Panel Door .
If the source has digital audio outputs, connect
them to the Optical 4 Digital Input * or the
Coaxial 4 Digital Jack Ó.
Connection Notes:
When making connections to the Component
Video Inputs + or the Coaxial or
Optical digital audio inputs, it is a good idea
to make note of which jacks are connected to
which source, using the Worksheet in the
Appendix. This will help simplify the configuration
process.
NOTE: When connecting a device such as a
digital cable box or other set-top tuner product
with a digital audio output, we recommend that
you connect both the digital and analog outputs
of the product to your AVR. The audio input
polling feature of the AVR will then be able to
make certain that you have a constant audio
feed, since it will automatically switch the audio
input to the analog jacks if the digital feed is
interrupted or not available for a particular
channel.
8. If you have a camcorder, video game or other
audio/video device that is connected to the AVR
on a temporary, rather than permanent basis,
connect the audio, video and digital audio outputs of that device to the Front Panel Inputs
*ÓÔ. A device connected to the Video 4
jacks Ô is selected as the Video 4 input, and
connected to the digital jacks *Ó it is selected as "Optical 4" or "Coaxial 4" input. (See
page 43 for more information on input configuration.)
9. Connect the AVR to your video display using
one of the following connections, even if you will
also use an HDMI connection:
• If your video display has component video
inputs (Y/Pr/Pb), connect the Component
Video Outputs .
• If your display does not have digital or
component video inputs, connect the Video
Monitor Output on the AVR to the
matching input on your display. Only one
connection is needed, and S-video is the higher
quality signal.
HDMI Connections
HDMI™ is the abbreviation for High-Definition
Multimedia Interface, which is quickly becoming
the standard connection point between
advanced video/audio source products and
displays, particularly for high-definition video
signals. HDMI is a digital connection, eliminating
the need to convert signals back and forth from
digital to analog.
Some source or display components in your
system may use DVI (Digital Video Interface) for
digital video connections. DVI carries the same
digital video signals as HDMI but uses a larger
connector and does not transport audio or
control signals. In most cases, you may mix and
match DVI and HDMI digital video connections
by using optional connector adapters. Note,
however, that some DVI-equipped video displays
are not compatible with the HDCP copy
protection coding that is increasingly carried with
signals connected via HDMI. If you have an
HDMI source and a DVI-equipped display, you
may occasionally be unable to view a program if
the display does not include HDCP. This is not the
fault of the AVR or your source; it simply
indicates that the video display is not compatible.
The AVR 445 is equipped for HDMI switching,
which means that it is able to select either of the
two HDMI inputs as the source that feeds your
system’s video display. This preserves the digital
signal in its original form by passing it directly
through from source to display. However, this
also means that the AVR does not have access to
the signal and thus it is not able to add menus or
on-screen messages to HDMI signals, or to
process the audio that may be part of the signal
in an HDMI connection.
Therefore, the following connections are required
when the AVR 445 is used with HDMI sources:
• Connect the HDMI output of a source to either
of the HDMI Inputs ".
• Connect the HDMI Output of the AVR to
an HDMI input on your display.
• Connect either an optical or coaxial digital
audio output from the source to the AVR. The
default connections are Optical 3 for a
source connected to HDMI 1 " and
Coaxial 3 for a source connected to
HDMI 2 ". You may use any digital or analog
audio source in conjunction with the HDMI
inputs, but if it varies from the default you
must make a change to the input’s setting, as
shown on page 24.
• Even when HDMI inputs are used, it is important to make sure that a component, S-video
or composite video connection is made
between the AVR and your display. This is
needed to view both the setup menus and
on-screen messages, and to view other (nonHDMI) video sources. The AVR 445 does not
convert analog video signals to HDMI.
INSTALLATION AND CONNECTIONS 17
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Installation and Connections
Installation and Connections
SCART A/V Connections
For the connections described above your video
device needs RCA (cinch) connectors or/and SVideo connectors for all Audio and Video signals:
Any normal video device (Not SVHS or High 8)
for only playback needs 3 RCA jacks, VCRs for
record and playback even 6 RCA jacks. Any
S-Video device (SVHS, High 8) needs 2 RCA
(Audio) and 1 S-Video jack (Video), if it´s a playback unit, or 4 RCA (Audio In/Out) and
2 S-Video (Video In/Out) jacks, if it´s a recording
VCR.
Many european video devices are equipped with
RCA (Cinch) or S-Video jacks only partially, not
for all audio and video in/outputs needed as
described above, but with a so called Scart or
Euro-AV connector (almost rectangular jack with
21 pins, see drawings on next page).
In that case the following Scart to Cinch adapters
or cables are needed:
• Units for playback, such as satellite receivers,
camcorders, DVD or LD players, need an
adapter from Scart to 3 RCA plugs, see fig. 1
(normal video devices) or from Scart to 2
RCA+1 S-Video plugs, see fig. 4 (S-Video
devices).
• HiFi VCRs need an adapter from Scart to 6 RCA
plugs, see fig. 2 (normal video), or from Scart
to 4 Audio+2S-Video jacks, see fig. 5
(S-Video VCR). Read carefully the instruction
attached to the adapter to find which of the six
plugs is used for the record signal to the VCR
(connect with the AVR´s Out jacks) and for the
playback signal from the VCR (connect with the
AVR´s In jacks). Do not misconnect Audio and
Video signals. Don´t hesitate to consult your
dealer, if you are uncertain.
• If you use only normal video devices the TV
monitor needs an adapter from 3 RCA plugs to
Scart (fig. 3) only. If also S-Video devices are
used an adapter from 2 RCA+1S-Video plugs
to Scart is needed additionally (fig. 6), connected to the SCART input on your TV that is provided for S-Video.
18 INSTALLATION AND CONNECTIONS
Downloaded from www.Manualslib.com manuals search engine
Note that only the video plugs (the "yellow"
cinch plug in fig. 3 and the S-Video plug in
fig. 6) must be connected to the TV Monitor
Output , and the volume on the TV must be
reduced to minimum.
Important Note for Adapter Cables:
If the cinch connectors of the adapter you’ll use
are labeled, connect the Audio and Video ”In”
plugs with the corresponding Audio and Video
”In” jacks on the AVR (and with a VCR connect
the ”Out” plugs to the ”Out” jacks on the AVR).
Note that with some adapter types it may be just
turned around: If no signal is audible/ visible
when the VCR is playing connect the “Out” plugs
to the ”In” jacks on the AVR and turned around.
If the adapter plugs are not labeled in that way,
pay attention to the signal flow directions as
shown in the diagrams above and in the instruction attached to the adapter. If uncertain, don’t
hesitate to consult your dealer.
Black
Black
Figure 1:
SCART/Cinch-Adapter for
playback;
signal flow:
SCART → Cinch
Yellow
Yellow
Red
Red
Black
Black
Red
Red
Blue 1
Blue
Yellow
Yellow
Figure 2:
SCART/Cinch-Adapter for
record and playback;
signal flow:
SCART ↔ Cinch
Green 1
Green
White
White
Black
Black
Figure 3:
Cinch/SCART-Adapter for
playback;
signal flow:
Cinch → SCART
Yellow
Yellow
Red
Red
Rot
Red
Figure 4:
SCART/S-Video Adapter
for playback;
signal flow:
SCART → Cinch
Schwarz
Black
S-Video InIn
S-Video
Schwarz
Black
Rot
Red
Blau1
Blue
Gelb
Yellow
Figure 5:
SCART/S-Video Adapter
for record and playback;
signal flow:
SCART ↔ Cinch
Important Note for the Use of
SCART-Cinch Adapters:
When video sources are connected to the TV
directly with a SCART cable, specific control
signals apart from Audio/Video signals will be
fed to the TV. These specific signals are: With all
video sources, the signal for automatic input
selection that switches the TV automatically to
the appropriate input as soon as the video
source is started. And with DVD players, the
signals automatically turning the TV to 4:3/16:9
format (with 16:9 TVs or with 4:3 TVs with
selectable 16:9 format) and turning the RGB
video decoder of the TV on or off, depending on
the DVD player´s setting. With any adapter cable,
these control signals will be lost and the
appropriate setting of the TV must be made
manually.
Note for RGB signal with SCART:
If you use a unit providing RGB signals on a
SCART output (as e.g. most DVD players do) and
you want to use that RGB signal, this SCART
output must be connected directly to your TV.
Although the AVR can switch three-way video
signals (like component signals Y/Pb/Pr), most
TVs need separate sync signals for RGB (also
with SCART) that cannot be switched and
provided by the AVR.
RGB signals can be pathed through the AVR only
when no separate sync signal is needed (see last
”Video Connection Note” on page 16).
S-Video InIn
S-Video
S-Video
Out
S-Video Out
Rot
Red
Figure 6:
SCART/S-Video Adapter
for playback;
signal flow:
Cinch → SCART
Schwarz
Black
S-Video Out
S-Video
Out
1
Also other colours possible, e.g. brown and grey.
INSTALLATION AND CONNECTIONS 19
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Installation and Connections
Installation and Connections
System and Power Connections
The AVR 445 is designed for flexible use with
multiroom systems, external control components
and power amplifiers.
Main Room Remote Control Extension
If the receiver is placed behind a solid or smoked
glass cabinet door, the obstruction may prevent
the remote sensor from receiving commands.
In this event, the remote sensor of any
Harman Kardon or other compatible device, not
covered by the door, or an optional remote
sensor may be used. Connect the Remote IR
Output of that device or the output of the
remote sensor to the Remote IR Input jack .
If other components are also prevented from
receiving remote commands, only one sensor is
needed. Simply use this unit’s sensor or a remote
eye by running a connection from the Remote
IR Output jack to the Remote IR Input
jack on Harman Kardon or other compatible
equipment.
Multiroom IR Link
The key to remote room operation is to link the
remote room to the AVR’s location with wire for
an infrared receiver and speakers or an amplifier.
The remote room IR receiver (this can be an
optional IR receiver or any other remotable
Harman Kardon device in the remote room with
IR sensor integrated) should be connected to the
AVR via standard coaxial cable. Connect the
Remote IR Output of the device or of the
optional sensor with the Multiroom IR Input
jack on the AVR’s rear panel.
If other Harman Kardon compatible source equipment is part of the main room installation, the
Remote IR Output jack on the rear panel
should be connected to the IR IN jack on that
source device. This will enable the remote room
location to control source equipment functions.
When a remote IR sensor is used to control nonHarman Kardon source equipment, we recommend that you make a direct connection or use
an optional, external IR “blaster” connected to
the Remote IR Carrier Output Jack ,. If you
are in doubt as to which IR Output jack to use
for the equipment in your system, contact your
dealer or installer, or the manufacturer’s support
site and ask whether the unit to be controlled
uses “full carrier” or “stripped” carrier IR
commands. When “full carrier commands” are
used, make the connection to the Remote IR
Carrier Output Jack ,. Otherwise, make the
connection to the Remote IR Output Jack as noted above.
20 INSTALLATION AND CONNECTIONS
Downloaded from www.Manualslib.com manuals search engine
NOTE: All remotely controlled components must
be linked together in a “daisy chain”. Connect
the IR OUT jack of one unit to the IR IN of the
next to establish this chain.
Multiroom Audio Connections
Depending on your system`s requirement and
distance from the AVR to the remote room, three
options are available for audio connection:
Option 1: Use high-quality, shielded audio interconnect phono cable from the AVR’s location to
the remote room. In the remote room, connect
the interconnect cable to a stereo power amplifier. The amplifier will be connected to the room’s
speakers. At the AVR, plug the audio interconnect
cables into the Multiroom Output Jacks on the AVR’s rear panel.
Option 2: Place the amplifier that will provide
power to the remote location speakers in the
same room as the AVR, and connect the
Multiroom Output jacks on the rear panel
of the AVR to the audio input of the remote room
amplifier. Use the appropriate speaker wire to
connect the optional power amplifier to the
remote speakers. High-quality wire of at least
2.5 mm2 is recommended for long multiroom
connections.
Option 3: Taking advantage of the AVR’s built-in
seven-channel amplifier, it is possible to use two
of the amplifier channels to power speakers in
the remote room. When using this option you will
not be able to use the full 7.1-channel
capabilities of the AVR in the main listening
room, but you will be able to add another
listening room without additional external power
amplifiers. To use the internal amplifiers to power
a remote zone, connect the speakers for the
remote room location to the Surround
Back/Multiroom Speaker Outputs '. Before
using the remote room you will need to configure
the amplifiers for surround operation by
changing a setting in the Multiroom menu,
following the instructions shown on page 47.
NOTE: For all options, you may connect an
optional IR sensor (Harman Kardon He 1000) in
the remote room to the AVR via an appropriate
cable. Connect the sensor’s cable to the
Multiroom IR Input on the AVR and use
the Zone II remote to control the room volume.
Alternatively, you may install an optional volume
control between the output of the amplifiers and
the speakers.
A-BUS Installation Connections
The AVR is among the very few receivers
available today that offers built-in A-BUS/READY
operation. When used with an optional A-BUS
keypad or control module, you have all the
benefits of remote zone operation without the
need for an external power amplifier.
®
To use the AVR with an approved A-BUS product,
simply connect the keypad or module that is in
the remote room to the AVR using standard
“Category 5” wiring that is properly rated for the
inwall use specific to the installation. Terminate
the wiring at the receiver end to a standard
RJ-45 jack in compliance with the instructions
furnished with the A-BUS module.
No further installation or adjustment is needed,
as the A-BUS connector on the AVR routes the
signals in and out of the keypad to their proper
destination for power, signal source and control.
The output fed to the A-BUS jack is determined
by the AVR’s multiroom system, and the menus
may be used as is.
RS-232 Connections
The AVR is equipped with an RS-232 Serial
Connection Port ) that may be used for two
purposes. When the port is connected to a
compatible, optional, external computer, keypad
or control system the AVR is capable of
bi-directional communications that enable the
external system to control the AVR, and for the
AVR to report status and handshake data back to
the controller. Use of the RS-232 port for this
type of control requires specific technical
knowledge, and we recommend that any connection and programming for control be made by a
trained installer or technician familiar with the
equipment being used.
The physical connection to the AVR’s RS-232 port
is a standard D-9 connection but to assure
compatible and proper operation, specific
software commands and pin wiring schemes may
be required.
USB Connections
The AVR 445 is one of the few A/V receivers to
offer a USB connection that may be used for
both playback of compatible audio content from
a computer and for loading of system updates
(when available).
The physical connection between a computer and
the AVR is a simple one, requiring only a cable
with a USB “A” type connector on one side and a
USB “Mini B” on the other.
Connect the larger, “A” connector on the cable to
your computer or a USB hub and the end with
the “Mini” USB connector to the USB Jack on the AVR’s rear panel.
NOTES ON USB:
• The USB jack on the AVR is for connection to a
computer, or to a hub connected to a
computer, only. DO NOT connect it directly to
other devices such as card readers, USB
memory storage devices, external hard drives,
USB accessories, digital cameras or cellular
phones. Connection to these devices may
cause damage to the device and/or the AVR
that is not covered by the AVR’s warranty.
• The AVR’s USB connection may only be used
for audio playback and system upgrades. It
may not be used for other purposes, such as
system control, video or still-image playback.
Trigger Jack Connection
The AVR is equipped with a low-voltage Amp
Trigger Jack - that may be used to activate
optional, external power amplifiers, screen
motors, motorized blinds or other compatible
products that may be part of a home theater
installation. Once the connections are made,
operation is seamless in that the low-voltage
control signal is sent to the screen, blinds or
other device when the AVR is turned on, and it is
turned off along with the AVR. Due to the
complexity of interfacing with powercontrolled devices, we strongly
recommend that the installation be done
by a qualified installer.
The AVR’s trigger jack is a 3.5mm mono plug
that delivers a 5-volt DC signal to the center pin
(“tip”) of the plug (+) with the outer shaft
(“ring”) of the plug as the negative (–) or ground
connection.
AC Power Connections
This unit is equipped with an accessory AC outlet. It may be used to power accessory devices,
but should not be used with high-current draw
equipment such as power amplifiers. The total
power draw to the Switched Outlet must
not exceed 100 watts.
The Switched outlet will receive power only
when the unit is on completely. This is recommended for devices that have no power switch or
a mechanical power switch that may be left in
the “ON” position.
NOTE: Many audio and video products go into a
Standby mode when they are used with switched
outlets, and cannot be fully turned on using the
outlet alone without a remote control command.
The AVR features a removable power cord that
allows wires to be run to a complex installation
so that the unit, itself, need not be installed until
it is ready for connection. When all connections
described above have been made, connect the
AC Power cord to the AC Power Cord Jack .
The AVR draws significantly more current than
other household devices such as computers that
use removable power cords. For that reason, it is
important that only the cord supplied with the
unit (or a direct replacement of identical
capacity) be used.
Once the power cord is connected, you are
almost ready to enjoy the AVR’s incredible power
and fidelity!
Speaker Selection
No matter which type or brand of speakers is
used, the same model or brand of speaker should
be used for the front-left, center and front-right
speakers. This creates a seamless front soundstage and eliminates the possibility of distracting
sonic disturbances that occur when a sound
moves across mismatched front-channel
speakers.
Speaker Placement
The placement of speakers in a multichannel
home-theater system can have a noticeable
impact on the quality of sound reproduced.
Once the center-channel speaker is installed,
position the left-front and right-front speakers so
that they are as far away from one another as
the center-channel speaker is from the preferred
listening position. Ideally, the front-channel
speakers should be placed so that their tweeters
are no more than 60cm above or below the
tweeter in the center-channel speaker.
They should also be at least 0.5 meter from your
TV set unless the speakers are magnetically
shielded to avoid colourings on the TV screen.
Note that most speakers are not shielded, even
with complete surround sets only the Center
speaker may be.
Depending on the specifics of your room
acoustics and the type of speakers in use, you
may find that imaging is improved by moving the
front-left and front-right speakers slightly forward of the center-channel speaker. If possible,
adjust all front loudspeakers so that they are
aimed at ear height when you are seated in the
listening position.
Using these guidelines, you’ll find that it takes
some experimentation to find the correct location
for the front speakers in your particular
installation. Don’t be afraid to move things
around until the system sounds correct. Optimize
your speakers so that audio transitions across the
front of the room sound smooth.
When the AVR is used in 5.1-channel operation,
the preferred location for surround speakers is on
the side walls of the room, at or slightly behind
the listening position. In a 7.1-channel system,
both side surround and back surround speakers
are required. The center of the speaker should
face you (see below).
A 6.1 surround speaker adds an additional center
back surround speaker to the system, enabling
you to enjoy the benefits of advanced surround
modes such as Dolby Digital EX, DTS-ES and
Harman Kardon’s proprietary Logic 7/7.1
processing.
To step up to a 6.1 system, first place the
speakers for a 5.1 system. The “sixth” speaker
should ideally be placed at the center of the
room’s rear wall, pointing directly toward the
front center channel speaker.
Depending on the type of center-channel speaker
in use and your viewing device, place the center
speaker either directly above or below your TV, or
in the center behind a perforated front-projection
screen.
INSTALLATION AND CONNECTIONS 21
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Installation and Connections
Installation and Connections
Note: The 6.1-channel configuration is not
recommended for the AVR 445. We strongly
recommend a 7.1-channel installation as
described below. When 6.1-channel materials are
played through a 7.1-channel system, the same
surround back channel information is played
through both the left and right surround back
speakers.
For more information on subwoofer placement,
as well as a variety of topics relating to audio
and home theater, visit the Technology section of
our Web site at www.harmankardon.com. Links
are provided there to informative white papers
written by the acoustic and electronics experts at
Harman Kardon and at our parent company,
Harman International Industries, Inc.
If you are only able to install a single surround
back speaker at this time, you will not be able to
run the full EzSet/EQ 7.1-channel calibration
procedure. In that case, we suggest you install all
of your speakers except the surround back
speaker, and run the EzSet/EQ procedure for a
5.1-channel system (see page 28). After EzSet/EQ
has finished, connect the single surround back
speaker to the left Surround Back Speaker
Outputs . Then follow the instructions
starting on page 30 to manually configure your
surround back speaker.
Notes on speaker placement:
1. The limitations of your listening room, including the placement of walls and furniture, may
make it difficult to follow the speaker placement
suggestions shown above. Depending on the
specific layout of the room, here are some ways
to compensate for unusual conditions:
We recommend that you consider adding a second surround back speaker as soon as possible.
Rear surround speakers are required when a full
7.1-channel system is installed, and they may
also be used in 5.1 channel mode as an alternative mounting position when it is not practical to
place the main surround speakers at the sides of
the room. Speakers may be placed on a rear wall,
behind the listening position. As with the side
speakers, the center of the rear surrounds should
face you. The speakers should be no more than
2 meters behind the rear of the seating area.
The additional Surround Back Left/Right speakers
are placed at about 150 degrees on the circle,
pointing inward, toward the listening area. The
easiest way to visualize the placement of these
speakers is to place the surround back left
speaker directly opposite the right front speaker
and to place the surround back right speaker
directly opposite the left front speaker.
Subwoofers produce largely nondirectional
sound, so they may be placed almost anywhere
in a room. Actual placement should be based on
room size and shape and the type of subwoofer
used. One method of finding the optimal location
for a subwoofer is to begin by placing it in the
front of the room, about 15cm from a wall, or
near the front corner of the room. Another
method is to temporarily place the subwoofer in
the spot where you will normally sit, and then
walk around the room until you find a spot
where the subwoofer sounds best. Place the
subwoofer in that spot. You should also follow
the instructions of the subwoofer’s manufacturer,
or you may wish to experiment with the best
location for a subwoofer in your listening room.
22 INSTALLATION AND CONNECTIONS
Downloaded from www.Manualslib.com manuals search engine
A) Front Channel Speaker Installation with
Direct-View TV Sets or Rear-Screen Projectors
5.1-Channel System
• Try to follow the suggested placement, but
move the speakers within a meter from the
preferred locations.
• Regardless of where they are placed, always try
to make certain that the main surround
speakers are the same distance from the front
speakers. (For example, try not to have the
right surround speaker further back into the
room than the left surround speaker.)
• If it is not possible to wall-mount or place
speakers on a shelf, consider the use of
optional floor stands, available for many
speakers.
6.1-Channel System
2. When using ceiling-mounted in-wall speakers,
follow the same guidelines shown for
conventional floorstanding or shelf-mounted
speakers.
3. When you have reassigned the surround back
channels for use in a multiroom system, follow
the speaker placement instructions for a
5.1-channel system for your main listening area
(see page 21).
At least 15 cm from celling
At least 60 cm
7.1-Channel System
Once the speakers have been placed in the room
and connected, the remaining steps are to
program the system configuration memories.
Although it is necessary to assign input/output
settings and surround mode choices manually,
we recommend that you take advantage of the
power and precision of EzSet/EQ to automatically
select and enter the settings for all other audio
parameters. This will not only save you time; it
will ensure that your room is calibrated and
equalized with an accuracy not possible when
these settings are made manually. You are now
ready to power up the AVR to begin these final
adjustments.
First Turn On
You are now ready to power up the AVR to begin
these final adjustments.
1. Make certain that the AC power cord is firmly
inserted in to the AC Power cord Recepticle
and plug the cord into an unswitched AC
outlet. To maintian the unit's safety rating,
DO NOT substitute the power cord for one with
lower current capacity.
2. Press the Main Power Switch 1 in until it
latches and the word “OFF” on the top of the
switch disappears inside the front panel. Note
that the Power Indicator 3 will turn orange,
indicating that the unit is in the Standby mode.
3. Remove the protective plastic film from the
main front-panel lens. If left in place, the film
may affect the performance of your remote
control.
4. Install the four supplied AAA batteries in the
remote as shown. Be certain to follow the (+)
and (–) polarity indicators that are on the top of
the battery compartment.
5. Turn the AVR on either by pressing the System
Power Control 2 or the Input Source
Selector % on the front panel, or via the
remote by pressing the Power On Button 3,
AVR Selector 5 or any of the Input
Selectors 46 on the remote. The Power
Indicator 3 will turn blue to confirm that the
unit is on, and the Main Information Display
˜ will also light up.
NOTE: After pressing one of the Input Selector
buttons 4 to turn the unit on, press the AVR
Selector 5 to have the remote control the AVR
functions.
Using the On-Screen Display
When making the following adjustments, you
may find them easier to make via the unit’s
on-screen display system. These easy-to-read
displays give you a clear picture of the current
status of the unit and facilitate speaker, delay,
input or digital selection you are making.
To view the on-screen menus, make certain that
you have made a video connection to the
appropriate matching input of your TV or
projector. In order to view the AVR 445’s displays,
the correct video source must be selected on the
video display. On-screen menus may be viewed
through component, S-video or composite video
connections, but they are not available when an
HDMI source is selected as the input or through
the HDMI Output .
IMPORTANT NOTE: When viewing the on-screen
menus using a CRT-based projector, plasma display
or any direct-view CRT monitor or television, it is
important that they not be left on the screen for an
extended period of time. As with any video display,
but particularly with projectors, constant display of
a static image such as these menus or video game
images may cause the image to be permanently
“burned into” the CRT. This type of damage is not
covered by the AVR warranty and may not be covered by the projector TV set’s warranty.
The AVR has two on-screen display modes,
“Semi-OSD” and “Full-OSD.” When making configuration adjustments, it is recommended that
the Full-OSD mode be used. This will place a
complete status report or option listing on the
screen, making it easier to view the available
options and make the settings on the screen. The
Semi-OSD mode uses one-line displays only.
Note that when the full OSD system is in use, the
menu selections are not shown in the Information Display ˜. When the full OSD menu system is used, OSD ON will appear in the Upper
Display Line ˜.
When the semi-OSD system is used in conjunction
with the discrete configuration buttons, the on
screen display will show a single line of text with
the current menu selection. That selection will also
be shown in the Upper or Lower Display Line
˜.
The full OSD system can always be turned on or
off by pressing the OSD button L. When this
button is pressed the MASTER MENU
(Figure 7) will appear, and adjustments are made
from the individual menus. Note that the menus
will remain on the screen for 20 seconds after
the latest action was made on the screen menu,
then they will “time-out” and disappear from the
screen. The time-out may be increased to as
much as 50 seconds by going to the
ADVANCED SELECT menu, and changing
the item titled FULL OSD TIME OUT.
The semi-OSD system is also available as a system default, although it may be turned off by
using the ADVANCED SELECT menu. (See
page 46). With the semi-OSD system, you may
make adjustments directly, by pressing the buttons on the front panel or remote control for the
specific parameter to be adjusted. For example,
to change the digital input for any of the sources,
press the Digital Select Button ÛG and
then any of the Selector buttons ‹ / › 7$ or
⁄/¤ E on the front panel or remote.
**
MASTER
MENU
**
→ IN/OUT SETUP
AUDIO ADJUST
SURROUND SETUP
EZSET/EQ
MULTI-ROOM
ADVANCED
Figure 7
The full-OSD menus remain on the screen for
twenty seconds after the last button press, after
which they “time out” and disappear from the
screen. The length of time menus remain on the
screen before the time-out may be increased to
as long as fifty seconds by adjusting the settings
for FULL OSD TIME OUT in the
ADVANCED SELECT menu, as shown on
page 46.
NOTE: Semi-OSD messages are not available
when a 480p or any high definition image is
being viewed.
System Setup
The AVR features an advanced memory system
that enables you to establish different
configurations for component video assignment,
digital input, surround mode for each input
source. To ease the speaker setting, the same
speaker setting can also be made for all inputs.
This flexibility enables you to custom tailor the
way in which you listen to each source and have
the AVR memorize them. This means, for
example, that you may associate different surround modes and analog or digital inputs with
different sources. Once these settings are made,
they will automatically be recalled whenever you
select that input.
To simplify initial configuration and operation,
the AVR has been preconfigured with input
settings that are typical for home theater
systems. These settings are detailed in the
worksheets in the Appendix. Before adjusting the
input settings, it is a good idea to compare your
input connections to the defaults so that you
may see where changes need to be made.
SYSTEM CONFIGURATION 23
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
System Configuration
System Configuration
Before using the unit, you will probably want to
change the settings for some inputs so that they
are properly configured to reflect the use of
digital or analog inputs and the surround mode
associated with the input. Remember that since
the AVR memorizes the settings for each input
individually, you will need to make these
adjustments for each input used. However, once
they are made, further adjustment is only
required when system components are changed.
To make this process as quick and as easy as
possible, we suggest that you use the full-OSD
system with the on-screen menus, and step
through each input.
In/Out Setup
The first step in configuring the AVR is to select
an input, i.e. to associate an analog or digital
input with each input source in use, e.g. CD or
DVD. Note that once an input is selected, all
settings for the Digital Input, Speaker Configuration and Surround Mode will ”attach” themselves to that input and be stored in a nonvolatile memory. This means that once made, the
selection of an input will automatically recall
those settings. For that reason, the procedures
described below must be repeated for each input
source so that you have the opportunity to
custom tailor each source to your specific
listening requirements. However, once made they
need not be changed again unless you need to
alter a setting.
When using the full-OSD system to make the
setup adjustments, press the OSD button L
once so that the MASTER MENU (Figure 7)
appears. Note that the ➞ cursor will be next to
the IN/OUT SETUP line. Press the Set
button F to enter the menu and the
IN/OUT SETUP menu (Figure 8) will
appear on the screen. Press the ‹/› buttons E
until the desired input name appears in the
highlighted video, as well as being indicated in
the front panel Input Indicators ˆ.
*
IN/OUT
SETUP
*
→ SOURCE: VIDEO 1
TITLE:
AUDIO IN-PORT: ANALOG
AUDIO AUTO POLL: ON OFF
VIDEO IN-PORT: AUTO
COMPONENT INPUT: COMP 1
VIDEO PROCESS: V CONVER
A/V SYNC DLAY: 0mS
MASTER MENU PAGE 2
Figure 8
When any input other than the tuner, 8-channel
inputs or USB input, is selected as the source,
you have the option of renaming the input as it
appears in the on-screen and front panel messages. This is helpful if you have more than one
VCR, if you wish to associate a specific product
brand name with the input, or to simply enter
any name that will help you to remember which
source is being selected.
24 SYSTEM CONFIGURATION
Downloaded from www.Manualslib.com manuals search engine
To change the input name, press the ⁄/¤
Navigation Button E on the remote so that
the ➞ cursor is pointing to TITLE. Next, press
and hold the Set Button F for a few seconds
until a flashing box appears to the right of the
colon. Immediately release the Set Button F,
as you are now ready to enter the device name.
Press the ⁄/¤ Navigation Button E and
note that a complete set of alpha-numeric
characters will appear with the start of the
alphabet in capital letters followed by the lowercase letters and then numbers and symbols.
When you press the ¤ Navigation Button
E, a series of symbols and numbers will
appear, followed by a reverse list of the alphabet
in lower-case letters. Press the button either way
until the first letter of the desired name appears.
If you wish to enter a blank space as the first
character, press the › Navigation Button E.
When the desired character appears, press the ›
Navigation Button E and repeat the process
for the next letter, and continue until the desired
name is entered, up to a maximum of fourteen
characters.
Press the Set Button F to enter the input
name into the system memory and to proceed
with the configuration process.
The audio input defaults for all sources except
the Tuner, USB and 6/8-Channel Direct inputs are
shown in the table in the Appendix. If your
system configuration follows the default table, no
changes are needed and you may press the
⁄/¤ Navigation Button EF to move to
the next line.
With the cursor pointing to AUDIO
IN-PORT, press the ‹ / › Navigation
Button EF to change the default to a
different audio input connection. When the name
of the desired input appears, press the ⁄/¤
Navigation Button EF to move to the
next line.
In normal operation, when a digital audio stream
is interrupted, the unit will automatically switch
to the analog inputs associated with that source.
This is particularly useful with cable set-top boxes
where the input is normally digital, but
occasionally changes to analog. If you wish to
configure an input so that the auto-poll circuit is
turned off, while the on-screen cursor is pointing
to the AUDIO AUTO POLL line, simply
press the ‹ / › Navigation Button EF so
that OFF (rather than O N) is in a white video
highlight.
When the desired auto-poll setting is entered,
press the ⁄/¤ Navigation Button EF to
move to the next line.
When the cursor is at the VIDEO IN-PORT
line, you are able to select an alternative to the
default input setting for the video input
associated with any source except HDMI 1 and
HDMI 2. For the Video 1 and Video 4 inputs, the
factory default of AUTO will select either
composite or S-video, depending on which has
an active signal. For the Video 2, Video 3 and
DVD inputs, the AUTO setting will normally
select the default component input, but if it is
not in use, the system will revert to a composite
or S-video output if either one is active.
You may set COMPONENT INPUT to OFF
if you aren’t using component video, and the AVR
will not select the component video inputs.
To have the AVR always look to a specific source
connection when an input is selected, make
certain that the on-screen cursor is pointing to
the VIDEO IN-PORT line, and then press
the ‹ / › Navigation Button EF until the
name of the desired input appears.
Note that this setting is not available when the
HDMI inputs are selected. The choice of available
inputs may vary according to whether an audioonly source (such as the tuner, CD or tape) or an
audio/ video source (such as Video 1–Video 4 or
DVD) is selected.
When the desired video input setting has been
made, press the ⁄/¤ Navigation Button
EF to move to the next line.
If your system includes any sources that are
equipped with Y/Pr/Pb component video outputs,
the AVR is able to switch them to send the
proper signals to your video display. Each of the
Component Video Inputs JL is
assigned to a default source, as shown in the
table in the Appendix, but if you have connected
your system differently than the factory settings,
you may select any of the three inputs for any
source except the HDMI inputs or the Tuner. If
your system does not include component video
at this time, or if you do not need to change
these defaults, press the ¤ Navigation Button
EF to go to the next setting.
To change the Component Video assignment,
first make certain that the ➞ cursor is pointing
to the COMPONENT I N line on the menu
screen, and then press the ‹ / › Navigation
Button EF until you see the desired input
in the highlighted video.
When the desired component input has been
selected, press the ¤ Navigation Button
EF go to the next setting.
At the VIDEO PROCESS line, you are able
to select whether video format conversion, is to
be used with the input source being configured.
If you do not need to change the setting, simply
press the ⁄/¤ Navigation Button EF to
move to the next line.
The V -CONVERSION setting will not apply
any video enhancement or processing to the
incoming video signal, but it will output it in one
of the following ways, depending on the input
source.
• A standard-definition (480i or 576i) analog
signal (composite, S-video or component) will
be converted so that it is available at its input
resolution, at the standard composite, S-video
or component analog video outputs. The signal
will also be available at the record outputs.
• An analog component high-definition signal
will be output at its input resolution as an
analog component signal, but not through the
analog composite or S-video monitor, or HDMI
or record outputs.
• HDMI input signals, regardless of their resolution, will be output through the HDMI outputs.
The BYPASS setting will not apply any video
enhancement or processing to the incoming
video signal, but it will output it in one of the following ways, depending on the input source.
• Analog signals (composite, S-video or component) will output only in the resolution and format that matches the input for both the main
“Monitor” connection as well as for the record
outputs.
• HDMI input signals, regardless of their resolution, will be output through the HDMI outputs.
When any needed change to the video processing setting has been made, press the ⁄/¤
Navigation Button EF to move to the
next line.
At the A/V SYNC DELAY line, you are able
to enter a setting that delays the audio output
slightly behind the video so that the loss of lip
sync that may occur due to digital video
processing in the transmission of a program, in
the playback unit or in the display is corrected.
This lack of lip sync is not a fault of the sources;
rather, it is a by-product of video signal
processing. In most cases, we recommend that
the delay adjustment be made using the directaccess controls on the remote so that you may
more accurately adjust the delay while viewing
the on-screen image, following the instructions
shown on page 33, but you may also make it
here using the menu system. As the amount of
delay needed may vary from one source to
another, we strongly recommend that you adjust
it for each input.
To adjust the A/V sync delay time from the
IN/OUT SETUP menu, make certain that
the cursor is pointing to the A/V SYNC
DELAY line, and then press the ‹ / ›
Navigation Button EF until the desired
amount of delay is applied so that the on-screen
video matches the audio.
When all configuration adjustments on this menu
screen have been made, press the ⁄/¤
Navigation Button EF until the onscreen cursor is pointing to PAGE 2 and then
press the Set Button FQ to move to the
second screen of input/output settings. If all
settings for input configuration are complete,
press the ⁄/¤ Navigation Button EF
until the on-screen cursor is pointing to
MASTER MENU and then press the Set
Button FQ to return to the main menu
screen.
The second page of the IN/OUT SETUP
menu (Figure 9) allows you to further configure
the AVR 445 for special custom features.
SE TU P
*
➔ VIDE O
4
:I N
OU T
REC
OU T
:A NA LO G
MAST ER
M E NU
P AG E
*
IN /O U T
1
Figure 9
An exclusive Harman Kardon feature is the ability
to switch front panel jacks from their normal use
as inputs to output connections so that portable
recording devices may easily be connected. The
front panel analog Video 4 Jacks Ô are
normally set as an input for use with camcorders,
video games and other portable audio/video
products, but they may be switched to an output
for connection to portable audio/video recorders.
To temporarily switch them to outputs, select the
IN/OUT SETUP menu. Press the ¤ button
EF until the on-screen ➞ cursor is pointing
to the VIDEO 4 line. Press the › button
EF so that the word OUT is highlighted.
Note that the Input/Output Status Indicator
( between the S and Composite video jacks
will turn red, indicating that the analog Video 4
jacks Ô are now record outputs.
Selection of the jacks as an output will remain
effective as long as the AVR is on. However, once
the unit is turned off, the jack will revert to its
normal use as an input when the unit is turned on
again.
The REC OUT line enables you to select what
the audio output is at the analog record outputs
for the input source being configured. Press the
‹ / › Navigation Button EF to choose
one of the following if you wish to change the
default setting:
• ANALOG selects an unprocessed passthrough of an analog source and is the default
setting for most inputs.
When the adjustment has been made, or if no
adjustment is required and all settings on this
page are complete, press the ⁄/¤ Navigation
Button EF until the on-screen cursor is
pointing to PAGE 1 and then press the Set
Button FQ to return to the main
IN/OUT SETUP menu to configure another
input, or if no further input configuration
adjustments are needed, press the ⁄/¤
Navigation Button EF until the onscreen cursor is pointing to MASTER MENU
and then press the Set Button FQ to
return to the main menu screen.
Audio Setup
This menu allows you to configure the tone controls. If you do not wish to change any of those
settings at this time, proceed to the next menu
screen. However, to make configuration changes
to those parameters, make certain that the
MASTER MENU is on the screen with the ➞
cursor pointing to the AUDIO SETUP line,
and press the Set Button FQ. The
AUDIO SETUP menu (Figure 12) will appear.
*
A UD IO
→TO N E
BA S S
TR E BL E
BA C K
TO
S ET U P
*
: I N
:0
:0
M AS TE R
OU T
M EN U
Figure 12
The first line controls whether or not the
bass/treble tone controls are in the signal path.
The normal default is for them to be in-line, but if
you wish to remove them from the circuit for
“flat” response, first make certain that the ➞
cursor is pointing to the TONE line on the
menu and press the ‹ / › Navigation Button
EF so that OUT is highlighted in reverse
video.
If you wish to leave the tone controls in the
signal path, the amount off boost or cut for bass
and treble may be adjusted by pressing the
⁄/¤ Navigation Button EF so that the
➞ cursor is next to the line for the setting you
wish to adjust. Next, press the ‹ / › Navigation
Button EF until the desired setting is
shown.
When all desired changes have been made on
this menu, press the ⁄/¤ Navigation Button
EF so that the ➞ cursor is next to the
B A C K T O M A I N M E N U line and press
the Set Button FQ.
• DSP DOWNMIX selects a two-channel
downmix of a multichannel digital input.
SYSTEM CONFIGURATION 25
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
System Configuration
System Configuration
Surround Setup
The next step for that input is to set the surround
mode you wish to use with that input. Since
surround modes are a matter of personal taste,
feel free to select any mode you wish – you may
change it later. The Surround Mode chart on page
36 may help you select the mode best suited to
the input source selected. For example you may
select Dolby Pro Logic II or Logic 7 for most
analog inputs and Dolby Digital for inputs
connected to digital sources. In the case of inputs
such as a CD Player, Tape Deck or Tuner, you may
wish to set the mode to Stereo, if that is your
preferred listening mode for standard stereo
sources, where it is unlikely that surround encoded material will be used. Alternatively, the 5
Channel Stereo or Logic 7 Music mode may also
be a good choice for stereo-only source material.
It is easiest to complete the surround setup using
the full-OSD on-screen menus. From the
MASTER menu (Figure 7), press the ⁄/¤
buttons EF until the ➞ cursor is next to the
SURROUND SELECT menu. Press the Set
Button FQ so that the SURROUND
SELECT menu (Figure 13) is on the screen.
** SURROUND SETUP **
➔SOURCE:
VIDEO 1
AUDIO IN PORT: ANALOG
AUDIO IN: PCM 44.1kHz
ADC SAMPLING: 48K 96K
SURR MODE: LOGIC 7
SURR SELECT: MUSIC 5.1
DEFAULT SURR: LAST
SURROUND CONFIG
DOLBY SURR SETUP
BACK TO MASTER MENU
Figure 13
The first line on the menu allows you to select
the input for which the specific surround settings
will be applied. Press the ‹/› Navigation
Buttons EF to select the input source to
be configured.
The AUDIO IN-PORT and AUDIO I N
lines are for display only and may not be
changed through the SURROUND SETUP
menu. The AUDIO IN-PORT displays the
physical connection source for the current active
input, and the AUDIO I N line shows the
signal type present. Note that an UNLOCK
message in the AUDIO I N line indicates that
a digital physical input source has been selected,
but that no data stream is present.
When the input selection has been made, press
the ⁄/¤ Navigation Button EF to move
to the next configuration line.
The ADC SAMPLING line is where you
determine whether the unit’s upsampling feature
is turned on or off. The default setting of 48kHz
puts the feature in a bypass, or “off,” mode and
will pass digital audio data through the DSP at
its native sample rate. To process incoming
44.1kHz signals at a higher resolution,
26 SYSTEM CONFIGURATION
Downloaded from www.Manualslib.com manuals search engine
upsampled 96kHz sample rate, press the ‹/›
Navigation Buttons EF once so that
96kHz is highlighted.
When the desired setting has been made, or if no
adjustment is required at this line, press the
⁄/¤ Navigation Button EF to move to
the next configuration line.
The SURR MODE and SELECT lines are
related, as they guide you to the choice of the
surround mode that will be activated whenever
the input being configured is selected.
At the SURR MODE line, press the ‹/›
Navigation Buttons EF to select the
surround mode group (such as Dolby modes, DTS
modes, Logic 7 modes, and DSP or Stereo modes)
that is applicable to the input source. After
making a selection, press the ⁄/¤ Navigation
Button EF to move to the SELECT line.
At the SELECT line, you are able to choose
the specific mode to be used from within the
major surround mode group. The choice of modes
is governed by the input type (as some modes
such as Dolby Digital or DTS-ES are not available
for analog sources), as well as by the speaker
configuration, since some modes are only
available when a full 7.1 speaker complement is
present. The full list of available modes is
detailed in the surround mode chart on page 36.
In addition, you may also use the settings in the
SURROUND CONFIG menus to delete
modes you do not normally use from the
available choices.
When both a surround mode group and a
specific surround mode have been selected, press
the ⁄/¤ Navigation Button EF to move
to the next configuration line.
The DEFAULT SURR mode line is where you
choose the mode that is activated when a digital
source is selected. The factory default setting of
LAST will activate the last-used mode for any
digital source. If you prefer to always have a
digital source switch to the specific mode
encoded by digital data flags in the incoming
audio data stream, press the ‹/› Navigation
Buttons EF so that ORIGINAL
appears.
Before proceeding to the SURROUND
CONFIG line, it is worth noting that the
settings in the submenus attached to that line
may require a considerable amount of time to
complete. Although they are useful in that they
allow you to customize the list of surround
modes that appear in normal use of the AVR, you
may wish to bypass those settings at this time so
that you may complete the configuration process.
You may return to this menu line at a later time,
once you have had a chance to listen to the
various surround modes and determine which
you want to “keep” and which you do not want
to use. The settings in this line are not primary
controls and do not impact the way the AVR
“sounds.”
To proceed to the SURROUND CONFIG
line, press the ⁄/¤ Navigation Button
EF to move to that line; otherwise, press it
again to move to the DOLBY SURR
SETUP line and skip to the instructions for
that setting.
The SURROUND CONFIG line is your
gateway to a broad range of surround mode
configurations. To continue, press the Set
Button FQ to go to the main
SURROUND CONFIG menu (Figure 14).
**
➔ L
D
D
D
P
P
O
O
O
T
C
C
SURROUND
GIC 7
LBY M
LBY 2
S CON
M 44.
M 96k
BACK
TO
U
.
F
1
G
L
0
I
/
C
LO
TI
C
G
48
ON
CONFIG
**
BAL:OFF
CONFIG
ONFIG
kHz
FIG
CONFIG
SURROUND
CONFIG
Figure 14
The LOGIC 7 GLOBAL line is the only item
on this menu page that is menu-specific, and it
allows you to select whether or not Logic 7 will
be the default surround mode for any incoming
audio signal. The default setting is OFF, which
chooses the native mode. Press the ‹/›
Navigation Buttons EF so that O N
appears, to activate the global Logic 7 setting for
this input.
The remaining five items in this menu are global
settings that take you to a submenu listing the
individual surround modes available within the
selected mode group. To select a surround mode
list, press the ⁄/¤ Navigation Button
EF until the on-screen cursor is pointing to
the desired mode, and then press the Set
Button FQ. Within each menu, press the
⁄/¤ Navigation Button EF to move the
cursor up and down through the list, and then
press the ‹/› Navigation Buttons EF to
turn the mode “ON” or “OFF.”
• When a mode is O N, the mode will appear in
all menu selections whenever you are changing
the surround mode.
• When a mode is OFF, the mode will not
appear.
• Some modes, such as Dolby Digital, DTS and
the Stereo mode in the PCM menus, are not
defeatable.
A complete list of the AVR 445’s surround modes
may be found on page 36, but here are some
items that will help you decide which modes you
want included in your setup, and which modes
you may wish to turn off.
• The DOLBY MULT CONFIG group
contains the surround modes available when a
multichannel Dolby Digital, encoded source is
present. This includes both the native Dolby
Discrete mode, which cannot be turned off, as
well as other modes which may be applied as
post-processing on the source and system
speaker configuration.
• The DOLBY 2.0 CONFIG group contains the surround modes available when a
two-channel Dolby Digital-encoded source is
present. This includes both the native Dolby
Discrete mode, which cannot be turned off, as
well as other modes which may be applied as
post-processing on the source and system
speaker configuration.
• The DTS CONFIG group contains the surround modes available when a DTS-encoded
digital source is present. This includes both the
native DTS Discrete mode, which cannot be
turned off, as well as other modes which may
be applied as post-processing on the source
and system speaker configuration.
• The PCM 44.1/48KHZ CONFIG
group contains the surround modes available
when a PCM digital data stream is present.
This includes not only PCM sources from DVD
or CD players, but also all two-channel analog
sources that are in use, as they are converted
to PCM within the AVR 445. The modes
available include the proprietary Dolby modes
(including Dolby Headphone and Dolby Virtual
Speaker), DTS processing, our own Logic 7
modes, the conventional “DSP” modes (such
as “Hall” and “Theater”) and the “Stereo”
modes.
• The PCM 96KHZ CONFIG group
contains the surround modes available when a
PCM digital data stream is present. This
includes not only 96kHz PCM sources from
DVD or CD players, but also all two-channel
analog sources when 96kHz is chosen in the
ADC SAMPLING mode line in the
SURROUND SETUP menu. The modes
available include the proprietary Dolby mode
(including Dolby Headphone and Dolby Virtual
Speaker), DTS processing, our own Logic 7
modes, the conventional “DSP” modes (such
as “Hall” and “Theater”) and the “Stereo”
modes.
Note: When a Dolby Digital or DTS source is
selected and playing, the AVR will select the
appropriate surround mode automatically, no matter which surround mode was selected for that
input as default. Then no other surround modes
will be available, except all Pro Logic II modes with
Dolby Digital 2 channel (2.0) recordings.
On the Dolby menu (Figure 15), the selection
choices include Dolby Digital, Dolby Pro Logic II
and IIx Music, Dolby Pro Logic II and IIx Cinema,
Dolby Pro Logic, Dolby Virtual Speaker Reference
and Wide, and Dolby 3 Stereo. A complete explanation of these modes is found on Page 36.
The Dolby Digital EX mode is only available when
the system is set for 6.1/7.1 operation by configuring the Surround Back speakers to “Small” or
“Large” as described on page 31. When a disc is
playing that contains a special “flag” signal in
the digital audio data stream, the EX mode will
be selected automatically. It may also be selected
using this menu or through the front panel or
remote controls. A complete explanation of these
modes is found on page 36.
the left and right channels. A higher number
(up to “7”) produces a tighter center channel
presentatioin.
• Dimension: This setting alters the perceived
depth of the surround field by creating a
shallower presentation that appears to move
sounds toward the front of the room, or a
deeper presentation that appears to move the
center of the sound field toward the back of
the room. The setting of “O” is a neutral
default, with the range of adjustment shown
as “R-3” for a deeper, rear-oriented sound to
“F-3” for a shallower, front-oriented sound.
• Panorama: Switch this setting on or off to add
an enveloping wrap-around presentation that
increases the perception of sound along the
sides of the room.
When all surround modes that are not required
have been turned off, press the ⁄/¤
Navigation Button EF until the onscreen cursor is pointing to BACK T O
SURROUND CONFIG; then press the Set
Button FQ.
To change these parameters, press the ⁄/¤
Navigation Buttons EF while the DOLBY
SURROUND menu is on the screen until the ➞
cursor is pointing to the line on the menu with
the parameter you wish to change. Then, press
the ‹/› Navigation Buttons EF to alter
the setting to your taste.
The final item on the SURROUND SETUP
menu is the DOLBY SURR SETUP line.
When the on-screen cursor is at this line, press
the Set Button FQ to call the DOLBY
SURROUND menu (Figure 13) up on the
screen.
Note that when the Dolby Digital mode is
selected there are additional settings available
for the Night mode that are associated with the
surround mode only, not with the input. That´s
why these settings must be made only once, not
with each input in use.
When the ➞ cursor is pointing to the MODE
line, press the ‹/› Navigation Buttons
EF to select the desired Dolby surround
mode, again remembering that the choice of
available modes will vary with the type of
program material being played and the number
of speakers in your system configuratioin.
**
DOLBY
➔ MODE:
C
D
P
N
E
I
A
I
N
M
N
G
T
E
O
H
BACK
E
N
R
T
R
S
A
:
SURROUND
SURROUND
DOLBY
M OD E :
C
D
P
N
E
I
A
I
N
M
N
G
T
E
O
H
B AC K
E
N
R
T
SURROUND
D OL BY
R
W ID TH :
S IO N
:
A MA
:
:O FF
M ID
T O
SU RR
**
D I GI TA L
M
A
X
SE L E CT
**
DOLBY PLIIx
MUSIC
WIDTH : 3
ION
: 0
MA: OFF ON
OFF MID MAX
TO
**
SETUP
Figure 15
When Dolby Pro Logic II Music or Dolby Pro Logic
IIx Music is selected as the listening mode, three
special settings are available to tailor the sound
field to your listening room environment and
your individual taste and preferences. (When
other Dolby Surround modes are selected, dotted
lines will indicate that these settings are not
active.)
• Center Width: This setting adjusts the balance
of the vocal information in the front
soundstage between the center and front
left/right speakers. The lower settings spread
the center channel sound more broadly into
Figure 16
Night Mode Settings
The Night mode is a feature of Dolby Digital that
uses special processing to preserve the dynamic
range and full intelligibility of a movie sound track
while reducing the peak level. This prevents
abruptly loud transitions from disturbing others,
without reducing the sonic impact of a digital
source. Note that the Night mode is only available
when the Dolby Digital surround mode is selected.
To adjust the Night mode setting from the menu
press the OSD Button LE so that the
MASTER menu appears. Then press the ¤
button EF to access the AUDIO
SETUP and press the Set Button FQ to
select the SURROUND SETUP menu. Press
Set FQ to select the DOLBY menu (see
fig. 15).
SYSTEM CONFIGURATION 27
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
System Configuration
System Configuration
To adjust the Night mode setting, make certain
that the › cursor is on the NIGHT line of the
DOLBY menu. Next, press ‹/ › Buttons
EF to choose between the following
settings.
OFF: When OFF is highlighted, the Night mode
will not function.
MID: When MID is in the highlighted video,
a mild compression will be applied.
MAX: When MAX is in the highlighted video,
a more severe compression algorithm will be
applied.
When you want to use the Night mode feature,
we recommend that you select the MID setting
as a starting point and change to the MAX
setting later, if desired.
Note that the Night mode may be adjusted
directly any time that Dolby Digital surround
mode is selected by pressing the Night button
B. When the button is pressed, the words
D-RANGE followed by the current setting
(MID, MAX, OFF) will appear in the lower
third of the video screen and in the Main
Information Display ˜. Press the ⁄/¤
buttons EF within five seconds to select the
desired setting, then press the Set Button
FQ to confirm the setting.
When all settings on the DOLBY
SURROUND menu have been competed, press
the ⁄/¤ Navigation Button EF until
the cursor is next to BACK T O SURROUND
SETUP and press the Set Button FQ.
You may then make any additional changes to
the available options from that screen, or use
⁄/¤ Navigation Button EF to move the
cursor to the BACK T O SURROUND
CONFIG menu and press the Set Button
FQ again to back up one menu.
At the main SURROUND SETUP menu, you
may change the SOURCE to make adjustments
to another input, or when all input sources have
been configured, use ⁄/¤ Navigation Button
EF to move the cursor to the BACK T O
MASTER MENU and press the Set Button
FQ to return to the main menu so that you
may move to the next step in configuring your
AVR 445.
Using EzSet/EQ
The AVR 445 uses Harman Kardon’s EzSet/EQ
technology to automatically configure your
system to deliver the best possible performance
based on your specific speaker selection, where
the speakers are placed in the room and the
acoustic influences in your listening room. By
using a series of test signals and the processing
power of the Texas Instruments DA 610 digital
signal processor, EzSet/EQ eliminates the need
for manual adjustment of speaker “size”,
28 SYSTEM CONFIGURATION
Downloaded from www.Manualslib.com manuals search engine
crossover, delay and output level settings while it
adds the power of a multi-band parametric
equalizer to smooth out the frequency settings
for optimal sound reproduction.
In addition to making system setup quick and
easy, EzSet/EQ is more precise than manual settings. With EzSet/EQ you are able to calibrate
your system in a fraction of the time it would
take to enter the settings manually, and with
results that rival those achieved with expensive
test equipment and time consuming procedures.
The end result is a system calibration profile that
enables your new receiver to deliver the best
possible sound no matter what type of speakers
you have or what the dimensions of your
listening room are.
We recommend that you take advantage of the
precision of EzSet/EQ to calibrate your system,
but if desired you may also make any of the
configuration settings manually, or trim the
settings provided by EzSet/EQ by following the
instructions on pages 31-34.
Before starting the EzSet/EQ process, make
certain that you have connected all speakers for
your system and that you have both the EzSet/EQ
microphone and the extender rod handy. If you
have a standard camera tripod, attach the
extender rod to the tripod, and then screw the
microphone to the top of the rod. Place the
tripod at your primary listening position, at least
one meter from the nearest speaker and adjust it
so that microphone is at least one meter above
ear level. If you do not have a tripod, simply
screw the extender rod into the bottom of the
EzSet/EQ microphone.
Next, plug the microphone into the EzSet/EQ
Microphone Jack ˘ located behind the Front
Panel Control Door. The microphone cable is
approximately 6 meters long, which should
accommodate most listening room situations. If
required, you may use an optional extension
cable, available at most electronics stores, for use
in larger rooms. However, we recommend that
you make every effort to avoid using extension
cords for the microphone cable as they may
adversely affect the test results.
Finally, before going further, make certain that
the program volume is at -35dB. If there is a
volume or “level” control on your subwoofer,
make certain that it is set to at least the
midpoint, if not a bit higher
You are now ready to start the EzSet/EQ process
by following these steps:
Step 1. Navigate to the EZSET/EQ MODE
menu (Fig. 17a) by first pressing the OSD
Button L on the remote. Press the ¤
Navigation Button E until the ➔ cursor is
pointing to EZSET/EQ in the MASTER
MENU. Press the Set Button F to bring the
menu to the screen.
*
E ZS ET /E Q
Se le c t
MA I N
*
ac ti vi ty
→ AU TO M AT IC
E Q
DE S IG N
MA NU A L
EQ
D ES IG N
EZ SE T /E Q
MA NU AL
SE TUP
BA CK
TO
M AS TE R
M EN U
Figure 17a
Step 2. Select one of the two options shown
based on the way you wish to have the system
settings entered:
• In most cases, you will want to use the
Automatic mode, which calibrates the system
for speaker presence, speaker “size”, speaker
crossover, channel output level, speaker-tolistener delay time and room equalization. To
choose this mode simply press the Set Button
F, as the cursor is already pointing to
AUTOMATIC E Q DESIGN when the
menu appears on the screen.
Then press the Set Button F again when the
AUTOMATIC EZSET/EQ menu appears,
to continue to Step 3.
• If you wish to enter the speaker crossover
frequencies yourself, but want to have the
EzSet/EQ system test for and calibrate all the
other functions listed above, press the ¤
Navigation Button E to point the cursor
at EZSET/EQ SETUP and then press the
Set Button F. Once the MANUAL
SETUP menu (Fig. 18) appears, follow the
instructions on page 30 to enter your desired
settings for the Crossover Frequencies, and
then return to the EZSET/EQ MAIN
menu. Press the ¤ Navigation Button E
again so that the cursor is pointing to
MANUAL E Q DESIGN and then press the
Set Button F. When the interim message
screen appears to remind you to set the
crossovers, make sure that the cursor is
pointing to CONTINUE and press the Set
Button F again since you have already set
the crossovers.
Step 3. The FAR FIELD MEASURE
screen (Figure 17b) will appear with instructions
to place the microphone, if you have not already
done so. This screen is also the place to set the
master volume level. As noted on the screen, use
the Volume Control ı to adjust the
volume level to –35dB, as shown on the line that
appears at the bottom of the menu when the
volume is adjusted. Press the Set Button F
when the volume is set to the proper level.
* FAR FIELD MEASURE *
Place mic at ear level
near the listening
position at least 3 ft/
1m from any hard
surface.
Set volume to -35dB
→ CONTINUE
BACK TO EZSET/EQ MAIN
BACK TO MASTER MENU
VOLUME: -35dB
Figure 17b
Step 4. The final menu screen before the
EzSet/EQ process starts is a warning screen
(Figure 17c) that serves as a reminder to keep
the room as quiet as possible while the system is
in use. Extraneous noise of any kind may
adversely affect the accuracy of the system’s
results. Do not talk while the test tones are
circulating, and if possible, turn off any
ventilation systems if the noise form the air flow
is loud enough for you to hear. Should an outside
noise such as a phone ringing occur during the
test process, we recommend that you rerun
EzSet/EQ. If you do not wish to start the test
process at this time, press the ⁄/¤
Navigation Button E to return to either the
EzSet/EQ menu or the Master Menu, and press
the Set Button F. To begin the EzSet/EQ
Near Field measurements, press the ‹ / ›
Navigation Button E so that O N is highlighted in reverse video, and press the Set
Button F.
NOTE: Once the EzSet/EQ process starts, the
volume control and Standby/Off switches are
temporarily disabled while the tests are in
progress. Do not adjust the volume or turn the
unit off until you see the on-screen message
change to indicate that EzSet/EQ is finished.
WARNING
!!
During measurement
please maintain silence
while several sound
bursts are heard.
→ START :
BACK TO
BACK TO
OFF ON
EZSET/EQ MODE
MASTER MENU
Figure 17c
Step 5. At this point you will begin to hear a
series of test tones circulate among all the
speakers in your system. While this is happening,
the AVR is reading the signal to determine which
speaker positions are active, what type of
speaker is present at each active position, what
the distance is from the listening position to each
speaker, and to begin to build a profile of the
impact of the room’s acoustics on the quality of
audio reproduction. When the test is completed
you will hear the tones stop, and the system will
pause fors long as a minute while the processor
makes its calculations. Do not be alarmed if the
“WARNING” message remains on the screen
after tones stop until a results message is
displayed as shown in Step 6 or 7, below.
NOTE: While these tests detect whether a
speaker is connected to a particular output, they
cannot determine whether the speaker is in the
correct position. (For example, it can tell whether
a speaker is connected to the Surround Right
output, but it cannot tell whether the speaker is
on the right or left side of your listening room.)
For that reason, we strongly recommend that you
try to listen as the tone circulates, matching the
name shown for each channel to the location of
the speaker. If a tone is heard from a speaker
position that does not match the on-screen
message, make a note of the incorrect speaker
connections. When the test process stops you will
see a message indicating the they Far Field
measurements are complete, but since there is a
connection error press the ¤ Navigation
Button E so that the on-screen cursor in
Fig. 7 is pointing to RETURN T O MASTER
MENU and press the Set Button F. At this
point, exit all menus and turn the receiver off.
Check all speaker wire connections and then
rerun EzSet/EQ.
Step 6. When the Far Field tests are complete a
message screen will appear to confirm if the
procedure was successful or not. In most cases
there will not be any problems and you will see
the message shown in Figure 17d on your
screen. If the speaker positions shown match the
actual speaker layout in your system, press the
Set Button F to complete EzSet/EQ by performing the Near Field Measurements. Continue
the EzSet/EQ process by pressing the Set
Button F to take the Near Field measurements from the front left, center and right
speakers. By taking this separate set of measurements, the AVR is able to complete its view of the
room’s sonic signature and apply equalization as
needed to correct spikes and dips in the system’s
response. Continue these instructions with
Step 8.
* FAR FIELD COMPLETE *
EQ successful
Speaker config detected
FL
: YES
SBR: YES
CEN : YES
SBL: YES
FR
: YES
SL : YES
SR
: YES
SUB: YES
→ DO NEAR
BACK TO
FIELD
MASTER
MENU
Figure 17d
Step 7a. If the measurements are not successful
due to a missing or malfunctioning speaker, the
FAR FIELD E Q ERROR message will
appear as shown in Figure 17e. EzSet/EQ is
programmed to look for speaker pairs at the
front left/front right, surround left/surround right
and surround back left/surround back right
positions. If the test results indicate that one, but
not both of the speakers in any of these pairs is
present, the menu will show N O next to the
speaker position where the tests did not report
back that a speaker is present. Should this
message appear, make note of the suspect
speaker location, exit all menus and turn the
receiver off. Check all speaker wire connections
and then rerun EzSet/EQ.
* FAR FIELD EQ ERROR *
Detected speaker config
FL
: YES
SBR: YES
CEN : YES
SBL: YES
FR
: YES
SL : YES
SR
: NO
SUB: YES
Verify spkr connections
Verify mic position
Reduce background noise
→ BACK TO MASTER MENU
Figure 17e
Step 7b. In some cases, the system may not
function properly due to overly high output
levels. When this occurs, you will see the message shown in Figure 17f. If you see this message
verify that that the microphone is in the correct
position, and not too close to any one speaker.
Then press the Set Button F to go back to
the MASTER MENU. From there, return to the
EzSet/EQ system and when you are once again at
the FAR FIELD MEASURE screen, reduce
the system volume level by 3dB before trying
EzSet/EQ again.
*
EZSET/EQ
ERROR
*
An overload was
detected. Please
verify mic position.
Reduce the volume by
6dB and repeat the
procedure.
→ BACK
TO
MASTER
MENU
Figure 17f
SYSTEM CONFIGURATION 29
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
System Configuration
System Configuration
Step 8. When the Far Field measurements are
completed, the system will ask you to take three
Near Field measurements, one at each front
speaker position. These measurements enable
EzSet/EQ to produce the most accurate settings
for both high and low frequency equalization.
The Near Field measurements are similar to the
Far Field tests, except that the system will
“listen” to only one speaker at a time, rather
than sending the test signals to all speakers in
rotation.
At the NEAR FIELD E Q SELECT menu
(Figure 17g) that should be on your screen after
completing the instructions in Step 6, press the
Set Button F to start the near field measurements with the front left speaker. If you are
repeating the setup process, you may also use
the ⁄/¤ Navigation Button E to select
any of the three speaker positions shown.
*
NEAR
FIELD
EQ
SELECT
*
Please select
→ 1. FL Speaker
2. C Speaker
3. FR Speaker
BACK
TO
MASTER
proceed to Step 11, if an “Error” message
appears, go to Step 12.
Step 11. If the test results were successful, the
message shown in Figure 17h will appear. In
order to properly calibrate the system, you will
need to run the Near Field tests for all three front
channel speakers (left, center and right). After
running the test for the front left speaker, make
certain that the cursor is pointing towards
BACK T O NEAR FIELD and press the Set
Button F. When you are taken back to the
Near Field Select menu (Figure 17g) where you
should repeat Steps 8 through 11 until all three
front speakers have been calibrated. When that is
done the EzSet/EQ process is complete and you
should press the ¤ Navigation Button E to
return to the Master Menu.
*
NEAR
FIELD
COMPLETE
*
EZSET/EQ has successFully performed
Near Field Eq for
the selected speaker.
→ BACK
TO
NEAR
BACK
TO
MASTER
FIELD
MENU
MENU
Figure 17h
Figure 17g
At the NEAR FIELD E Q SELECT menu
(Figure 17g), you will see an instruction to place
the microphone in a different position than the
one used for the initial Far Field measurements.
This time, place the microphone close to the
speaker to be measured, at a distance of about
60 cm. In addition, the top of the microphone
should be pointed towards the speaker, rather
than pointing up as was done for the Far Field
tests. For the first measurement, place the
microphone so that it is close to, and pointing
towards, the front left speaker, and with the
on-screen ➔ cursor pointing to 1 . F L
SPEAKER, and press the Set Button F.
Step 9. You will now see a Warning message
similar to the one shown in Figure 17c except
that it will contain an option to return to the
NEAR FIELD E Q SELECT menu (Figure
17g) as well as the ability to return to the
MASTER MENU. If you are ready to proceed
with the test, make certain that the microphone
is properly pointed toward the speaker selected
for calibration, press the › Navigation Button
E so that O N is highlighted and press the
Set Button F.
Step 10. One short test signal will be sent to the
speaker position being calibrated and after a
slight pause fro the system to calculate the test
results, you will see either a “Near Field
Complete” message or a “Near Field Error”
message. In most cases, the “Complete”
message will appear, in which case you should
30 SYSTEM CONFIGURATION
Downloaded from www.Manualslib.com manuals search engine
Step 12. If a “Near Field Error” message
appears, as shown in Figure 17i, you should
check to make certain that the microphone is
about 60 cm from the speaker being tested and
that the top of the microphone unit is pointing
towards the speaker. You may also have to raise
or lower the master volume to achieve accurate
readings. After checking these two items, as
needed, make certain that the cursor is pointing
to the BACK T O NEAR FIELD line and
press the Set Button F. This will return you to
the NEAR FIELD E Q SELECT menu
(Figure 17g) where you should repeat Steps 8
through 11, adjusting the mike placement and
volume level as needed until the NEAR
FIELD COMPLETE menu (Figure 17h)
appears after the test tone stops.
*
NEAR
FIELD
Near Field Eq
successful.
ERROR
*
was
not
Please check mic
Placement and volume
Setting
→BACK TO NEAR FIELD
BACK TO MASTER MENU
Figure 17i
When both the Far Field and Near Field measurements have been successfully completed your
system is ready for use. Thanks to EzSet/EQ, the
settings for speaker “size”, speaker crossover,
channel output and individual channel delay time
have been automatically set and require no
further adjustment. In addition, EzSet/EQ also
performs a complete room equalization that
tailors the system’s performance for the best
possible sound with your combination of
speakers, speaker placement and room acoustics.
The next few pages in this manual detail the
procedure for manually entering system data, but
unless you want to view the setting information
and make an adjustment, you are now ready to
enjoy the finest in home theater and music
reproduction. Go to page 38 for complete
information on operating your AVR.
Manual Setup
In most cases it is simpler, easier and more
accurate to let EzSet/EQ take care of entering the
system parameters for speaker “size”, speaker
crossover, channel output and individual channel
delay time. However, if you feel that your listening room or system components are best suited
to manual entry of these settings, the AVR 445
also allows you to enter or trim any of these
traditional system parameters. Even if you do
make the settings manually, we recommend that
you run the EzSet/EQ tests first so that a baseline
setting is established, and then make your
adjustments from there. Note that once EzSet/EQ
has been run you do not need to adjust all system settings, only those that you want to adjust.
To view or change the current settings, press the
OSD Button L on the remote to bring up the
MASTER MENU (Figure 7). Next, press the ¤
Navigation Button E as needed until the
cursor is on the EZSET/EQ line. Navigate to
the EZSET/EQ MANUAL SETUP line.
Press the Set Button F to view the
MANUAL SETUP menu (Figure 18).
*
→
MANUAL
SETUP
*
EzSet EQ : OFF
EzSet ADJUST
SPEAKER SIZE
DELAY ADJUST
CHANNEL ADJUST
ON
BACK
MENU
TO
MASTER
Figure 18
If you have already run the EzSet/EQ calibration
system, the first line of the menu enables you to
hear the difference between the settings
established by EzSet/EQ. The default setting is
O N, which plays the incoming source with the
EzSet/EQ settings. To hear the system in a Bypass
mode, with none of the equalization filters in the
circuit path, press the ‹ / › Navigation Button
E so that OFF is highlighted. Note that once
changed, this setting will remain until you
change it again in this menu. While you may
want to use this menu option to hear the
difference that EzSet/EQ makes, we recommend
that you leave the setting on to take advantage
of the benefits of EzSet/EQ’s advanced room
correction technology.
The EZSET ADJUST line on the menu
enables you to set the system’s Tilt, or high-frequency boost. To make this adjustment, first
make sure that EZSET E Q line is set to ON, as
this item is not available when EzSet EQ is not in
the signal path. When the cursor is on the
EZSET ADJUST line, press the Set Button
F, and then press the ‹ / › Navigation
Button E to enter the desired setting. When
you have completed your adjustment, press the ›
Navigation Button E to move the cursor
down to the BACK T O MANUAL SETUP
line and press the Set Button F.
Note on Manual Setup Menus: Each of the
four major manual setup menus (Speaker Size,
Speaker Crossover, Delay Adjust and Channel
Adjust) includes a line that reads EZSET
SETTINGS. When the default setting of
OFF is shown you are able to make any
required adjustments that are available on that
menu. However, you may change the setting to
O N at any time to recall the settings established
when EzSet/EQ was last run. It is also important
to note that when the EzSet/EQ settings are in
use, the AVR will not allow any changes to be
made. To trim the settings press the ‹ / ›
Navigation Button E until the cursor is on
the EZSET SETTINGS line on the menu in
use and press the ‹ / › Navigation Button E
to change the setting to OFF. This will allow
you to make changes to the settings on that
menu.
Speaker Size Menu
Although most listeners will prefer to take
advantage of the accuracy and speed of EzSet/EQ
to make all of the necessary speaker adjustments, advanced users may wish to experiment
with how different combinations of settings
sound in their home theater environment or to
use settings other than those calculated by
EzSet/EQ, to accommodate personal listening
preferences.
The menu system used in your AVR differs somewhat from conventional speaker setup menus in
that it consolidates the speaker “size” and
crossover into one convenient menu. Even if you
are familiar with making these adjustments, it is
strongly recommended that you read the
following section of this manual.
On the SPEAKER SIZE menu (Figure 19)
you have the option to change the type of
speaker configured for each of the four position
groups, to change the crossover setting for any
one of those speakers, to adjust the setting point
for the low-pass filter that determines which
frequencies are sent to the subwoofer for lowfrequency effects (LFE) signals, to change the
subwoofer bass redirection mode when the Front
Left/Right speakers are set to Large and to
change the setting for the subwoofer size. If, as
recommended, you have first run the EzSet/EQ
system, as shown on pages 28-31, the settings
established by EzSet/EQ will be displayed as a
starting point for any manual adjustments. You
may reestablish those settings at any time during
an adjustment on this menu by pressing the
⁄/¤ Navigation Button E until the cursor
is on the EZSET SETTINGS line of the
menu and then pressing the ‹/› Navigation
Button E so that O N is highlighted in reverse
video. Note, however, that once this is done, any
manual adjustments made will be lost and must
be reentered.
Speaker Size
At each of the four speaker group positions, you
have the ability to select the speaker “size” and,
when a “Small” speaker is selected, the frequency below which low-frequency information
is sent to the subwoofer, as opposed to the
speakers for the channel being adjusted. For that
reason, before making the adjustments on the
FRONT L/R, CENTER, SIDE SURR
and BACK SURR menu lines, it is important
to know the frequency range for the speaker. This
information is typically found in the “Specifications” section of the speaker’s owner’s manual. If
you cannot find the specification for the lowest
frequency the speaker can handle, start with the
settings entered by running EzSet/EQ and then
try one setting above or below the existing entry.
We do not recommend changing the crossover
point more than that due to the possible impact
that will have on the speaker’s performance. If
you do not have access to the owner’s manual
for a particular speaker, you should be able to
obtain the needed information from the Web site
or customer service department of the speaker’s
manufacturer.
To manually adjust the speaker settings, go to
the SPEAKER SIZE menu by pressing the
OSD Button L on the remote and when the
MASTER MENU (Figure 7) appears, press the
⁄/¤ Navigation Button E until the cursor
is on the MANUAL SETUP line and press the
Set Button F. When the MANUAL
SETUP menu (Figure 18) appears, press the
⁄/¤ Navigation Button E again until the
cursor is on the SPEAKER SIZE line and
press the Set Button F.
On the SPEAKER SIZE menu (Figure 19)
you will see a display of either the settings that
were established when EzSet/EQ was run, or the
factory default settings if you have not yet run
the automated system.
*
SPEAKER
SIZE
*
→ FRONT L/R
:SM - 100Hz
CENTER
:SM - 100Hz
SIDE SURR
:SM - 100Hz
BACK SURR
:SM - 100Hz MAIN
LFE LP FLT :120 Hz
SUB MODE
:SUB
SUB SIZE
:10in/250mm
EZSET SETTINGS: OFF
ON
BACK TO MANUAL SETUP
Figure 19
To change the setting for any of the four speaker
positions, press the ⁄/¤ Navigation Button
E until the cursor points to the line where you
wish to make the change. Press the ‹/›
Navigation Button E to change the setting,
but note that when you do this for the first time
in the menu, a warning message (Figure 20) will
appear in the on-screen display reminding you to
rerun EzSet/EQ after you are finished with any
speaker configuration changes. This is necessary
to make any level output adjustments needed
after the setting changes so that the new
configuration will be properly integrated.
*
X-OVER
CHANGE
WARNING
*
Speaker X-Over Freq or
Size has been changed.
Please
re-run
EZSET/EQ
Figure 20
The warning message will remain for four
seconds and then the SPEAKER SIZE
menu will return to the screen. At this point you
may change the settings to the “size” or
crossover for any of the four speaker positions
using the Navigation Buttons E as shown
above. The information below details the settings
available for each of the speaker configurations.
At each of the four speaker position lines, you
have the option to set the speaker size and
crossover. Note that the “size” does not refer to
the speaker’s actual physical size, but rather to
the ability of the speaker to reproduce low-frequency information. If your speakers at any
position are traditional full-range models capable
of handling the full audio spectrum, select
LARGE. These speakers are called “large”
since the low-frequency drivers required to play
bass without strain or distortion are typically
eight to fifteen inches in diameter, in turn making
the speaker cabinet larger than those with small
(or no) low-frequency drivers. When the speakers
at a particular position are smaller frequencylimited speakers that do not have the ability to
properly reproduce low-frequency sounds, select
SMALL.
SYSTEM CONFIGURATION 31
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
System Configuration
System Configuration
At all speaker positions except for the front
left/right speakers, you may also select NONE.
This setting tells the system that no speakers are
present at that position, allowing the AVR to
select the correct surround modes that are
compatible with the number of speakers
installed. For example, in order to use the Dolby
Digital EX, Dolby Pro Logic IIx, DTS-ES, Logic 7/7channel and “7 Stereo” modes, you must have
either LARGE or SMALL speakers entered as
the setting for the BACK SURR channels.
When LARGE is selected for any channel, a
full-range signal will be sent to the speaker outputs for that channel. For all speaker positions
except the front left/right, when LARGE is
chosen, no derived sound will be sent to the
subwoofer output, although in all cases the
special low-frequency effects (LFE) signals
available on 5.1 or 6.1 digital programs will
always be sent to the subwoofer output.
When SMALL is selected for any channel, you
may also enter a setting for the crossover
frequency at which sound is divided between the
frequency above which sound is sent to the
channel’s speakers and below which sound is
sent to the subwoofer. When configuring a
“small” speaker, choose the setting that has the
frequency closest to that of the lowest frequency
the speakers in question are capable of handling.
If one of the six available crossover points does
not match, select the one that is above, but
closest to, the speaker’s low-frequency limit.
When there are no speakers available at a
specific position, select NONE. When this option
is chosen for the Center or Side Surround
speakers, the sound that would normally be sent
to these channels will be split between the front
left and right speakers. Note that when your
system does not include Center or Surround
speakers, the use of Dolby Virtual Speaker as a
surround mode may provide a sound field that
simulates the presence of these speakers. (See
page 37 for more information on the Dolby
Virtual Speaker mode.)
Note that when NONE is selected for the Back
Surround speakers, the 6.1/7.1 channel surround
modes are not available. When this is the case
for your system you may wish to take advantage
of the availability of the unused amplifier channel
pair to power a second set of speakers in another
room. See page 47 for more information on
amplifier configuration.)
Once any desired changes have been made to
the speaker size and/or crossover, press the
⁄/¤ Navigation Button E to move the
cursor to any other line on this menu to make a
setting change, or go to the BACK T O
MANUAL SETUP menu and then press the
Set Button F to continue with overall
configuration.
32 SYSTEM CONFIGURATION
Downloaded from www.Manualslib.com manuals search engine
LFE Low-Pass-Filter Setting
The LFE L P FLT line selects the frequency
setting below which sounds that may be
available from a special low-frequency effects
(LFE) track are sent to the subwoofer. In most
cases, this setting will be set accurately by
EzSet/EQ but, should you wish to make a change
from that setting or the 120Hz frequency that is
most commonly used in the creation of LFE
channels by motion picture sound mixers, after
making sure that the SPEAKER SIZE menu
(Figure 19) is on the screen, press the ⁄/¤
Navigation Button E so that the cursor is
pointing to LFE L P FLT. Press the ‹/›
Navigation Button E to begin the selection
process, and note that the warning message
(Figure 20) will appear reminding you to rerun
EzSet/EQ after all changes have been made.
When the SPEAKER SIZE menu returns to
the screen, press the ‹/› Navigation Button
E to make your selection. When the desired
setting appears, press the ⁄/¤ Navigation
Button E to move the cursor to any other line
on this menu where you wish to make a setting
change, or go to the BACK T O MANUAL
SETUP menu and then press the Set Button
F to continue with overall configuration.
Sub Mode Setting
When the Front Left/Right speakers are configured as “Large” and a subwoofer is detected
by EzSet/EQ or manually configured as being
available, additional options are available to
further customize bass redirection. To change
these settings, first make sure that the
SPEAKER SIZE menu (Figure 19) is on the
screen, and then press the ⁄/¤ Navigation
Button E so that the cursor is pointing to
SUB MODE. Press the ‹/› Navigation
Button E to begin the selection process, and
note that the warning message (Figure 20) will
appear reminding you to rerun EzSet/EQ after all
changes have been made.
The following options are available:
• The default setting for Large front left/right
speakers when a subwoofer is present is SUB
L/R + LFE. In this mode, all sounds below
the crossover point set on the LFE L P FLT
line will be sent to BOTH the subwoofer and
the front left/right speakers.
• To send only the LFE channel information to
the subwoofer, but have all other (“derived”)
low-frequency sounds sent to the front
left/right speakers, select the SUB (LFE)
setting.
• To have low-frequency information sent to the
subwoofer only when Large speakers are
selected, choose SUB (L/R). This option is
only available when the unit is set to
SURROUND OFF so that a pure analog
audio path is provided.
• When no subwoofer is present and Large
speakers are configured for the front left/right
position, select NONE. This will route all lowfrequency information to the front left/right
speakers.
When the SPEAKER SIZE menu returns to
the screen, replacing the warning message, press
the ‹/› Navigation Button E to make your
selection. When the desired setting appears,
press the ⁄/¤ Navigation Button E to
move the cursor to any other line on this menu
where you wish to make a setting change, or go
to the BACK T O MANUAL SETUP menu
and then press the Set Button F to continue
with overall configuration.
Subwoofer Size
The final setting on the SPEAKER SIZE
menu enables you to change the setting for the
subwoofer size. In the event that EzSet/EQ did
not accurately enter the correct size, or if you
wish to experiment with a different setting, first
make sure that the SPEAKER SIZE menu
(Figure 19) is on the screen; then press the ⁄/¤
Navigation Button E so that the cursor is
pointing to SUB SIZE and then press the ‹/›
Navigation Button E to begin the selection
process. Note that a warning message will
appear for 4 seconds to remind you to rerun
EzSet/EQ after all changes have been made.
Select a setting that best matches the diameter
of your subwoofer’s driver, or which provides the
appropriate high-pass filter setting for your system. In each case, the frequency of the high-pass
filter determines the frequencies below which no
information is sent to the subwoofer:
• The setting for an 8-inch/200mm driver
activates a 38Hz subwoofer high-pass filter.
• The setting for a 10-inch/250mm driver
activates a 30Hz subwoofer high-pass filter.
• The setting for a 12-inch/305mm driver
activates a 20Hz subwoofer high-pass filter.
• The setting for a 15-inch/380mm driver
activates a 15Hz subwoofer high-pass filter.
When all changes to Speaker-related settings
have been made, press the ⁄/¤ Navigation
Button E until the cursor is on the BACK
T O MANUAL SETUP menu and then
pressing the Set Button F so that you may
make any other adjustments to the system
parameters. It is also important to remember to
rerun the EzSet/EQ system if any changes have
been made to the settings on this menu,
following the instructions shown on page 30 for
using the Manual mode.
The Speaker Configuration may also be changed
at any time without using the full-OSD on-screen
menu system by pressing the Speaker Selector
6 on the front panel or on the remote
control. Once the button is pressed, FRONT
SPEAKER will appear in both the lower third
of the video display and the Main Information
Display ˜.
Within five seconds, either press the ‹/› buttons
7 $ on the front panel or the ⁄/¤ buttons
E on the remote to select a different speaker
position, or press the Set Button @F to
begin the adjustment process for the front left
and right speakers.
When the Set button @ F has been pressed
and the system is ready for a change to the front
speaker setting, the on-screen display and Main
Information Display ˜ will read FRONT
LARGE or FRONT SMALL depending on
the current setting. Press the ‹/› buttons 7 $
on the front panel or the ⁄/¤ buttons E on
the remote until the desired setting is shown,
using the instructions for “large” or “small”
shown earlier, then press the Set button @F.
If another speaker position needs to be changed,
press the ‹/› buttons 7 $ on the front panel
or the ⁄/¤ buttons E on the remote to
select a different speaker position, press the Set
button @ F and then the ‹/› buttons 7 $
on the front panel or the ⁄/¤ buttons E on
the remote until the correct speaker setting is
shown and press the Set button @ F again
to confirm the selection.
To assist in making these settings, the icons in
the Speaker/Channel Input Indicators Ú
will change as the speaker type is selected at
each position. When only the inner icon box is lit,
the speaker is set for “small.” When the inner box
and the two outer boxes with circles inside them
are lit, the speaker is set for “large." When no
indicator appears at a speaker location, that
position is set for “none” or “no” speaker.
Note: These icons are available only when
making setup changes without the use of the full
OSD mode.
As an example, in the Figure below, all speakers
are set for “large,” and a subwoofer is set.
compensate for this difference through the use of
the delay settings to adjust the timing for the
specific speaker placement and acoustic
conditions in your listening room or home
theater.
To re-synchronize the front, center and surround
channels at first measure and note the distance
from the listening/viewing position to the front,
center, surround and surround back (if any)
speakers in meters.
If you have already calibrated your system using
Ezset/EQ the delay settings shown will reflect the
results of the measurements made by Ezset/EQ.
No further changes are needed unless you wish
to change an item to reflect your taste or a
nonstandard system configuration. To change the
settings, follow the instructions below to enter
the distance between the speaker’s location and
your main listening position. The measurements
need not be accurate to the inch, as the system is
designed to accommodate typical listening rather
than a specific “sweet spot” position.
The Delay setting for all speakers configured for
your system will be available only (with 5.1 or
with 6.1/7.1 configuration) when any Dolby surround mode is selected (except Dolby-3-Stereo).
In addition they are selectable with these modes
only, with all other modes the delay times are
fixed. Note that the Delay settings are "Global"
for all inputs, using those Dolby modes, and need
not to be repeated with any input.
To view or change the current delay settings,
make sure the EZSET/EQ MAIN menu
(Figure 17a) is on the screen. Press the ⁄/¤
Navigation Button EF to move the
cursor to DELAY ADJUST and then press
the Set Button FQ. The DELAY
ADJUST menu (Figure 21) will appear on the
screen.
→
* DELAY ADJUST *
FL :12 ft
SBR:10 ft
CEN:12 ft
SBL:10 ft
FR :12 ft
SL :10 ft
SR :10 ft
SUB:12 ft
DELAY RESET: OFF ON
UNIT: FEET METER
EZSET SETTINGS
BACK TO MANUAL
: OFF
SETUP
ON
Figure 21
Delay Settings
Due the different distances between the listening
position for the front channel speakers and the
surround speakers, the amount of time it takes
for sound to reach your ears from the front or
surround speakers is different. You may
Next move the ➞ cursor to the UNIT line and
select the unit for distances you prefer to enter,
feet or meter. Then move the ➞ cursor to the
F L line where the first adjustment is made. Now
press the ‹ / › Buttons EF until the
distance from the front left speaker to the
preferred listening position is entered. Next press
the ¤ Button EF once to move to the next
line.
If you wish to reset all delay settings to the
factory defaults, as shown in Figure 21, press the
⁄/¤ Navigation Button EF until the
cursor is pointing to the DELAY RESET line.
Next, press the ‹/› Navigation Button
EF so that O N is highlighted in reverse
video. The settings will reset, and you may now
continue to make any needed changes following
the instructions shown below. Once you make
the first change to the default settings, the
setting on the DELAY RESET line will return
to OFF, indicating that the factory defaults are
no longer in effect.
Now the ➞ cursor will be at the CEN line so
that the delay for the center speaker may be set.
Press the ‹ / › Buttons EF until the
distance from the main listening position to the
center speaker is entered. Repeat the procedure
for all active speaker positions by pressing the
¤ Button EF again and use the
‹ / › Buttons EF to change the setting.
If you have already run Ezset/EQ, return to the
settings established by the automated system by
pressing the ⁄/¤ Navigation Button EF
until the cursor is pointing to the EZSET
SETTINGS line. Next, press the ‹/›
Navigation Button EF so that O N is
highlighted in reverse video. The settings will be
resent to the values calculated by Ezset/EQ, and
the menu will be locked so that the settings may
not be changed. To go back into the menu and
make any manual changes to one or more
channels, you must first return the cursor to the
EZSET SETTINGS line and press the ‹/›
Navigation Button EF so that OFF is
highlighted in reverse video. This will unlock the
menu to allow changes.
When the delay time for all speaker positions has
been set you may return to the master menu by
pressing the ⁄/¤ Navigation Button EF
until the ➞ cursor is pointing to BACK T O
MANUAL SETUP and then pressing the Set
Button FQ.
Note that the delay settings may also be
adjusted at any time when the Dolby Digital or
Dolby Pro Logic II modes are in use by pressing
the Delay button on the remote . Then press
the ⁄/¤ E buttons on the remote to select
the Center or Rear channels for adjustment,
followed by a press of the Set button F. Next,
press the ⁄/¤ buttons E on the remote until
the desired figure appears in the Main
Information Display ˜ and press the Set
button p twice to confirm the setting and
return to the normal display.
When the delay settings are complete, press the
¤ Button EF once so that the cursor is
next to the BACK T O MANUAL SETUP
menu line and press Set Button FQ to
return to the MANUAL SETUP menu.
SYSTEM CONFIGURATION 33
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
System Configuration
System Configuration
Output Level Adjustment
Output level adjustment is a key part of the
configuration of any surround-sound product. It
is particularly important for a digital receiver such
as the AVR, as correct outputs ensure that you
hear sound tracks with the proper directionality
and intensity.
In most cases, you will not need to make any
adjustments to the output level, as the settings
made by running Ezset/EQ are as accurate as
those made manually. However, you are able to
use the CHANNEL ADJUST menu to trim
the settings to suit your personal preferences or
to configure the system so that the output
settings are different from one input source to
another. The ability to make individual output
level adjustments on a per-input basis is useful
for listeners who may prefer different settings for
the subwoofer or an individual channel group
such as the front speakers when playing musical
selections via the CD input as opposed to the
movie soundtracks more frequently used with the
DVD input. This menu also allows you to adjust
the output levels using external sources such as a
test disc or other program material that you use
as a standard, rather than the system’s test tone.
NOTE: Listeners are often confused about the
operation of the surround channels. While some
assume that sound should always be coming
from each speaker, most of the time there will be
little or no sound in the surround channels. This
is because they are only used when a movie
director or sound mixer specifically places sound
there to create ambience, a special effect or to
continue action from the front of the room to
the rear. When the output levels are properly
set, it is normal for surround speakers to
operate only occasionally. Artificially increasing
the volume to the rear speakers may destroy the
illusion of an enveloping sound field that
duplicates the way you hear sound in a movie
theater or concert hall.
Before beginning the output level adjustment
process, make certain that all speaker
connections have been properly made. The
system volume should be turned down at first.
To view or change the current Channel Output
settings, make certain that the EZSET/EQ
MAIN menu (Figure 17a) is on the screen. Press
the ⁄/¤ Navigation Button EF to move
the cursor next to CHANNEL ADJUST and
then press the Set Button FQ. The
CHANNEL ADJUST menu (Figure 22) will
appear on the screen.
34 SYSTEM CONFIGURATION
Downloaded from www.Manualslib.com manuals search engine
*
CHAN NEL AD JUST
*
FL
: 0 dB
SB R : 0dB
→ C EN : 0 dB
SB L : 0dB
FR
: 0 dB
SL
: 0dB
SR
: 0 dB
SW 1 : 0dB
T EST TO NE: AU TO OFF MAN
L EVEL R ESET: O FF ON
C H ADJU ST: GL OBAL
E ZSET S ETTING S: OFF ON
B ACK TO MANUA L SETUP
Figure 22
To provide the maximum flexibility, channel
output level adjustments may be made either
with or without the internal test tone, and when
the tone is in use, it may be programmed to
automatically circulate among the active
channels or to only move from one channel to
the next on your command. When the
CHANNEL ADJUST menu appears, we
recommend that you first run the test tone once
in the automatic mode to verify that the speakers
have been properly connected. To do this, press
the ⁄/¤ Navigation Button EF again
until the cursor is on the TEST TONE line and
then press the ‹ / › Navigation Button
EF until AUTO is in highlighted video. The
test tone will then circulate among all channels
for five seconds at each position.
IMPORTANT NOTE: Because this test noise will
have a much lower level than normal music, the
volume must be lowered after the adjustment for
all channels is made, but BEFORE you return to
the main menu and the test tone turns off.
NOTE: Remember to verify that the speakers
have been properly connected. As the test noise
circulates, listen to make certain that the sound
comes from the speaker position shown in the
Main Information Display ˜. If the sound
comes from a speaker location that does NOT
match the position indicated in the display, turn
the AVR off using the Main Power Switch 1
and check the speaker wiring or connections to
external power amplifiers to make certain that
each speaker is connected to the correct output
terminal.
After checking for speaker placement, let the test
noise circulate again, and listen to see which
channels sound louder than the others. Using the
front left speaker as a reference, press the ‹/ ›
Buttons EF on the remote to bring all
speakers to the same volume level. When one of
the ‹/ › buttons is pushed, the test noise
circulation will pause on the channel being
adjusted to give you time to make the
adjustment. When you release the button, the
circulation will resume after five seconds. The onscreen cursor ➞ and the test noise can also be
moved directly to the speaker to be adjusted by
pressing the ⁄/¤ buttons EF on the
remote.
Continue to adjust the individual channels until
the volume level sounds the same from each
speaker. Note that adjustments should be made
with the ‹/ › Buttons EF on the remote
only, NOT the main volume controls.
If you are using a sound-pressure level (SPL)
meter for precise level adjustment with the test
tone, open the main Volume Control to
-15dB and set the individual output level for
each channel so that the meter reads 75dB,
C-Weighted Slow. After all settings are made turn
the main volume down.
You may also make these same adjustments with
complete manual control over the channel being
adjusted by pressing the⁄/¤ Navigation
Button EF until the ➞ cursor is pointing to
the TEST TONE line on the menu and then
using the ‹/› Navigation Button EF to
select MAN in the highlighted video. In the MAN
mode, the test tone will also start immediately, but
the tone will only be moved to another channel by
pressing the ⁄/¤ Navigation Button EF.
When the manual sequencing mode is active, the
tone is turned off by pressing the ⁄/¤
Navigation Button EF until the ➞ cursor
is pointing to the TEST TONE line and the
‹/› Navigation Button EF is then pressed
to select OFF in the highlighted video.
The final option for tone adjustment using the
menu system is to not use the internal test tone
at all. To do this, simply use the ⁄/¤
Navigation Button EF to change the
channel and then use the ⁄/¤ Navigation
Button EF to change the output level.
When making channel output adjustments
without the internal test tone we strongly recommend that you use a test disc in the “repeat”
mode on your DVD or CD player so that the
signal being used is constant throughout the
adjustment process.
NOTE: The subwoofer output level is not
adjustable using the test tone. To change the
subwoofer level, follow the steps for Output
Level Trim Adjustment on page 44.
When all channels have an equal volume level,
the adjustment is complete. Now turn the
Volume down to about -40dB, otherwise
the listening level may be too high as soon as
the source’s music starts to play. To exit this
menu, press the ⁄/¤ buttons EF until the
on-screen ➞ cursor is next to the BACK T O
MANUAL SETUP line, and then press the
Set Button FQ to return to the MANUAL
SETUP.
The output levels may also be adjusted at any
time using the remote control and semi-OSD
system. To adjust the output levels in this
fashion, press the Test Button 8. As soon as
the button is pressed, the test tone will begin to
circulate as indicated earlier. The correct channel
from which the test noise should be heard will be
shown in the lower third of the video screen and
in the Main Information Display ˜. While
the test noise is circulating, the proper channel
position will also be indicated in the Speaker/
Channel Input Indicators Ú by a blinking
letter within the correct channel. Turn up the
Volume until you can hear the test noise
clearly.
To adjust the output level, press the ⁄/¤
buttons E until the desired level is shown in
the display or on screen. Once the buttons are
released, the test noise will begin to circulate
again in five seconds.
IMPORTANT NOTE: The Output level
adjustment made will be effective for all inputs,
but only for the actual surround mode selected.
To be effective for any other mode select that
mode (with any input) and repeat the level
adjustment described above. This will also allow
you to compensate level differences between
speakers, that may be different with each
surround mode, or to increase or decrease the
level of certain speakers intentionally, depending
on the surround mode selected.
Note: Output level adjustment is not available
for the Surround Off mode, as no surround
speakers are used (so level differences between
the speakers in the room cannot occur). But to
compensate level differences between stereo and
other surround modes (independently from the
input selected) the outputs can be adjusted with
the Level Trim Adjustment procedure, see page
44, also for the Surround Off (Stereo) modes.
In addition to the controls for selecting channels
and the test tone operation, the settings on this
menu also allow you to reset the level settings to
either the factory default of 0dB or to reestablish the settings that were entered by
running Ezset/EQ.
To reset all channel levels to 0dB press ⁄/¤
Navigation Button EF so that the cursor
is pointing to the LEVEL RESET line and
then press the ⁄/¤ Navigation Button
EF once so O N appears in highlighted
video.
To return to the settings established by Ezset/EQ,
even if you have made manual changes to the
output trims using the steps shown above, press
⁄/¤ Navigation Button EF so that the
cursor is pointing to the EZSET
SETTINGS line and then press the ⁄/¤
Navigation Button EF once so O N
appears in highlighted video. Remember that
after turning the Ezset/EQ settings back on you
must turn return to this menu line and change
the setting to OFF if you wish to make any
manual trim adjustments.
The final setting in this menu enables you to
have the output levels remain the same for all
inputs or to be adjusted differently for each (or
any) input. While most listeners prefer to keep
the same output levels for all sources, you may
wish to raise or lower some channels, particularly
the subwoofer output for a specific source such
as a CD that is primarily used for music playback.
To enter individual settings for a specific channel,
first make sure that you have either run Ezset/EQ
and/or made any desired manual trim
adjustments to set a baseline for all channels.
After that is done, press the OSD Button E to
exit the menu system and then select the input
for which you wish to enter different level
settings by using either the Input Source
Selectors % on the front panel or the buttons
on the remote that are used to select an input
source BCD. Next, return to the
CHANNEL OUTPUT submenu using the
steps outlined above.
Additional Input Adjustments
After one input has been adjusted for Surround
mode, digital input (if any), speaker type, and
output levels, go back to the IN/OUT
SETUP line on the MASTER MENU
(Figure 7) and enter the settings for each input
that you will use. In most cases, only the digital
input and surround mode will be different from
one input to the next, while the speaker type,
crossover frequency, Night mode and output
level settings will usually be the same and may
be quickly entered by entering the same data
used for the original input.
Once the settings outlined on the previous pages
have been made, the AVR is ready for operation.
While there are some additional settings to be
made, these are best done after you have had an
opportunity to listen to a variety of sources and
different kinds of program material. These
advanced settings are described on pages 45 to
46 of this manual. In addition, any of the settings
made in the initial configuration of the unit may
be changed at any time. As you add new or
different sources or speakers, or if you wish to
change a setting to better reflect your listening
taste, simply follow the instructions for changing
the settings for that parameter as shown in this
section.
Having completed the setup and configuration
process for your AVR, you are about to
experience the finest in music and home theater
listening. Enjoy!
At the CHANNEL OUTPUT menu press
Navigation Button EF until the
cursor is pointing to the LEVEL TRIM line
and then press the ⁄/¤ Navigation Button
EF once so that INDEPENDENT
appears in highlighted video. When this setting is
active you may change the channel output levels
for any input without changing the settings
previously established for another.
⁄/¤
NOTE: With the default GLOBAL setting,
output levels are associated with the various
surround modes. As you spend time listening to
various materials and selecting a variety of
surround modes, you may wish to revisit the
CHANNEL ADJUST menu to set the output
levels.
When all changes to the Channel Output levels
and the associated level trim settings have been
made press the ⁄/¤ Navigation Button
EF until the cursor is on the BACK T O
MANUAL SETUP menu and then pressing
the Set Button FQ so that you may make
any other adjustments to the system parameters.
If the changes just made complete the manual
adjustments needed, press the OSD Button E
to exit the menu system and resume normal
system operation.
INTRODUCTION 35
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
System Configuration
Operation
Surround Mode Chart
MODE
FEATURES
DOLBY DIGITAL
Available only with digital input sources encoded with Dolby Digital data. It provides
up to five separate main audio channels and a special dedicated Low Frequency Effects
channel.
DOLBY DIGITAL EX
Available when the receiver is configured for 6.1/7.1 channel operation, Dolby Digital EX is the
latest version of Dolby Digital. When used with movies or other programs that have special
encoding, Dolby Digital EX reproduces specially encoded soundtracks so that a full 6.1/7.1
soundfield is available. When the receiver is set for 6.1/7.1 operation and a Dolby Digital signal is
present, the EX mode is automatically selected. Even if specific EX encoding is not available to
provide the additional channel, the special algorithms will derive a 6.1/7.1 output.
DTS 5.1
When the speaker configuration is set for 5.1-channel operation, the DTS 5.1 mode is
available when DVD, audio-only music or laserdiscs encoded with DTS data are played.
DTS 5.1 provides up to five separate main audio channels and a special dedicated
low-frequency channel.
DTS-ES 6.1 Matrix
DTS-ES 6.1 Discrete
When the speaker configuration is set for 6.1/7.1 operation, playback of a DTS-encoded program
source will automatically trigger the selection of one of the two DTS-ES modes. Newer discs with
special DTS-ES discrete encoding will be decoded to provide six discrete, full-bandwidth channels
plus a separate low-frequency channel. All other DTS discs will be decoded using the DTS-ES Matrix
mode, which creates a 6.1-channel sound field from the original 5.1-channel soundtrack.
DOLBY PRO LOGIC II
MOVIE
MUSIC
DOLBY PRO LOGIC
GAME
Dolby Pro Logic II is the latest version of Dolby Laboratory’s benchmark surround technology
that decodes full-range, discrete left, center right, right surround and left surround channels
from matrix surround encoded programs and conventional stereo sources when
an analog input or a digital input with PCM or Dolby Digital 2.0 recordings is in use. The
Dolby Pro Logic II Movie mode is optimized for movie soundtracks that are recorded with matrix
surround, by creating separate center, rear left and rear right signals. while the Pro Logic II Music
mode should be used with musical selections that are recorded with matrix surround or even with
normal stereo mode, creating separate rear left and rear right signals in any case. The Pro Logic II
mode creates compelling five-channel surround sound from conventional stereo recordings. Game
mode ensures that special effects are routed to the surround channels, while delivering their full
impact using the subwoofer, thus fully immersing the game player in the universe of the video game.
DOLBY PRO LOGIC IIx
MUSIC
MOVIE
GAME
Dolby Pro Logic IIx is the latest extension of Dolby Pro Logic II technology that creates a discrete
6.1 and 7.1 sound field from matrix surround or two-channel stereo sources in systems
configured for surround back speakers. Both Movie and Music versions of Pro Logic IIx are
available. Movie, Music and Game versions of Pro Logic IIx are available. Game mode ensures that
special effects are routed to the surround channels, while delivering their full impact using the
subwoofer, thus fully immersing the game player in the universe of the video game.
Logic 7 Cinema
Logic 7 Music
Exclusive to Harman Kardon for AV receivers, Logic 7 is an advanced mode that extracts the
maximum surround information from either surround-encoded programs or conventional stereo
material. Depending on the number of speakers in use and the selection made in the SURROUND
SELECT menu, the “5.1” versions of Logic 7 modes are available when the 5.1 option is chosen,
while the “7.1” versions of Logic 7 produce a full sound field presentation, including back surround
speakers when the “6.1/7.1” option is chosen. The Logic 7 C (or Cinema) mode should be used
with any source that contains Dolby Surround or similar matrix encoding. Logic 7 C delivers
increased center-channel intelligibility, and more accurate placement of sounds with fades and pans
that are much smoother and more realistic than with former decoding techniques. The Logic 7 M or
Music mode should be used with analog or PCM stereo sources. Logic 7 M enhances the listening
experience by presenting a wider front soundstage and greater rear ambience. Both Logic 7 modes
also direct low-frequency information to the subwoofer (if installed and configured) to deliver
maximum bass impact. Logic 7 adds additional bass enhancement that circulates low frequencies in
the 40Hz to 120Hz range to the front and surround speakers to deliver a less localized soundstage that
appears broader and wider than when the subwoofer is the sole source of bass energy.
36 OPERATION
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Operation
Surround Mode Chart
MODE
FEATURES
DTS Neo:6 Cinema
DTS Neo:6 Music
These two modes are available when any analog source is playing to create a six-channel
surround presentation from conventional Matrix-encoded and traditional Stereo sources. Select
the Cinema version of Neo:6 when a program with any type of analog Matrix surround encoding
is present. Select the Music version of Neo:6 for optimal processing when a nonencoded,
two-channel stereo program is being played.
DTS 96/24
DTS 96/24 is a high-resolution format that uses a 96kHz sampling rate with 24 bits to produce extended
information that improves the harmonics of the source material. The AVR is capable of automatically detecting
and decoding DTS 96/24 materials and delivering them as the artist intended.
THEATER
The THEATER mode creates a sound field that resembles the acoustic feeling of a
standard live performance theater, with stereo and even pure mono sources.
HALL 1
HALL 2
The two Hall modes create sound fields that resemble a small (HALL1) or
medium sized (HALL 2) concert hall, with stereo and even pure mono sources.
Dolby Virtual Speaker
Reference
Wide
Dolby Virtual Speaker technology uses a next-generation advanced algorithm to reproduce the
dynamics and surround sound effects of a precisely placed 5.1-channel speaker system using only
front left and right speakers. In the Reference Mode, the apparent width of the sound across
the front image is defined by the distance between the two speakers. The Wide Mode
provides a wider, more spacious front image when the two speakers areclose together.
5-Channel Stereo
7-Channel Stereo
This mode takes advantage of multiple speakers to place a stereo signal at both the front and
back of a room. Depending on whether the AVR has been configured for either 5.1 or 6.1/7.1
operation, one of these modes, but not both, is available at any time. Ideal for playing music in
situations such as a party, this mode places the same signal at the front-left and surround-left,
and at the front-right and surround-right speakers. The center channel is fed a summed mono
mix of the in-phase material of the left and right channels.
SURROUND
OFF (STEREO)
This mode turns off all surround processing and presents the pure left- and rightchannel presentation of two-channel stereo programs.
Dolby Headphone
Dolby Headphone enables ordinary stereo headphones to portray the sound of a five-speaker
surround-playback system.
OPERATION 37
Downloaded from www.Manualslib.com manuals search engine
Operation
Basic Operation
Once you have completed the setup and
configuration of the AVR, it is simple to operate
and enjoy. The following instructions should be
followed for you to maximize your enjoyment of
your new receiver:
Turning the AVR On or Off
• When using the AVR for the first time, you must
press the Main Power Switch 1 on the front
panel to turn the unit on. This places the unit in a
Standby mode, as indicated by the amber color of
the Power Indicator 3. Once the unit is in
Standby, you may begin a listening session by
pressing the System Power Control 2 or the
Source button % on the front panel or the
AVR Selector 5B. Note that the Power
Indicator 3 will turn blue. This will turn the unit
on and return it to the input source that was last
used. The unit may also be turned on from Standby
by pressing any of the Source Selector buttons
on the remote 4567BCD or
the Source button % on the front panel.
To turn the unit off at the end of a listening
session, simply press the System Power
Control 2 on the front panel or the Power
Off Button 3A on the remote. Power will
be shut off to any equipment plugged into the
rear panel Switched AC Outlets and the
Power Indicator 3 will turn orange.
When the remote is used to turn the unit “off” it
is actually placing the system in a Standby mode,
as indicated by the orange color of the Power
Indicator 3.
When you will be away from home for an
extended period of time it is always a good idea
to completely turn the unit off with the front
panel Main Power Switch 1.
NOTE: All preset memories may be lost if the
unit is left turned off with the Main Power
Switch 1 for more than two weeks.
Using the Sleep Timer
• To program the AVR for automatic turn-off,
press the Sleep Button 9 on the remote. Each
press of the button will increase the time before
shut down in the following sequence:
90
min
80
min
70
min
60
min
50
min
40
min
30
min
20
min
10
min
OFF
The sleep time will be displayed in the Lower
Display Line ˜ and it will count down until
the time has elapsed.
38 OPERATION
Downloaded from www.Manualslib.com manuals search engine
When the programmed sleep time has elapsed,
the unit will automatically turn off (to Standby
mode). Note that the front panel display will dim
to one half brightness when the Sleep function is
programmed. To cancel the Sleep function, press
and hold the Sleep Button 9 until the
information display returns to normal brightness
and the Sleep indicator numbers disappear and
the words SLEEP OFF appear in the Main
Information Display ˜.
Source Selection
• To select a source, press any of the Source
Selector buttons on the remote 467
CD.
NOTE: After pressing one of the Input Selector
buttons 4D to turn the unit on, press the
AVR Selector 5B to have the remote
control the AVR functions.
• The input source may also be changed by
pressing the front-panel Input Source Selector
button %. Each press of the button will move
the input selection through the list of available
inputs.
• As the input is changed, the AVR will automatically switch to the digital input (if selected),
surround mode component video input, A/V Sync
Delay and Night Mode configurations that were
in effect the last time that input was used.
• The front-panel Video 4 Inputs Ô, Optical
Digital 4 Input * or the Coaxial Digital 4
Input Ó may be used to connect a device such
as a video game or camcorder to your home
entertainment system on a temporary basis.
When the Video 4 Inputs Ô are configured as
outputs (see page 25) you can also connect an
audio or video recorder (composite or S-Video)
for recording the source selected.
• As the input source is changed, the new input
name will appear momentarily as an on-screen
display in the lower third of the video display. The
input name will also appear in the Main
Information Display ˜.
• When a pure audio input (CD, Tuner, Tape,
6/8 Channel Input) is selected, the last video
input used remains routed to the Video
Outputs (except from its own Video 1/
source) and Video Monitor Output . This
permits simultaneous viewing and listening to
different sources.
• When a Video source is selected, its audio
signal will be fed to the speakers and the video
signal for that input will be routed to the
appropriate Monitor Output Jack and will be
viewable on a TV monitor connected to the AVR.
If a component video source is connected to the
DVD + or Video 1 or 2 Component
Inputs, it will be routed to the Component
Video Outputs . Make certain that your TV is
set to the proper input to view the appropriate
video signal (composite, S-Video or component
video.
6-Channel/8-Channel Direct Input
• There are four input choices available for use
with sources such as a DVD-Audio or SACD
player that are connected to the 8-Channel
Direct Inputs . Select the appropriate input
according to the way your system and source
equipment is configured:
• The 6 CH DIRECT input should be used when
the SBR and SBL inputs are NOT in use and the
input source device has its own internal bass
management system. This input passes the input
from the source directly through to the volume
control without any analog to digital conversion
and it mutes the unused input jacks to prevent
unwanted noise from interfering with system
performance.
• The 6 CH DVD AUDIO input should be used
when the SBR and SBL inputs are NOT in use and
the input source device does NOT have its own
internal bass management system. When this
input is in use the analog source is converted to
digital so that you may use the same Quadruple
Crossover bass management options for the
direct input as you do with all other inputs. This
input also mutes the unused input jacks to
prevent unwanted noise from interfering with
system performance.
• The 8 CH DIRECT INPUT should be used when
an input is connected to all eight 8-Channel
Direct Inputs and when the input source
device has its own internal bass management
system. This input passes the input from the
source directly through to the volume control
without any analog to digital conversion.
• The 8 CH DVD AUDIO input should be used
when an input is connected to all eight
8-Channel Direct Inputs and the input
source device does NOT have its own internal
bass management system. When this input is in
use the analog source is converted to digital so
that you may use the same Quadruple Crossover
bass management options for the direct input as
you do with all other inputs.
Note that when the 6-Channel or 8-Channel
Input is in use, you may not select a surround
mode, as the external decoder determines the
processing in use. In addition, there is no signal
at the record outputs or bass management when
the 6-Channel or 8-Channel Direct Input is in use
and the tone or balance controls will not
function.
Controls and Use of Headphones
• Adjust the volume to a comfortable level using
the front panel Volume Control ı or remote
Volume Up/Down I buttons.
• To temporarily silence all speaker outputs press
the Mute button K. This will interrupt the
output to all speakers and the headphone jack,
but it will not affect any recording or dubbing
that may be in progress. When the system is
muted, the word MUTE will blink in the Main
Information Display ˜. Press the Mute
button K again to return to normal
operation.
• During a listening session you may wish to
adjust the Bass Control and Treble Control to
suit your listening tastes or room acoustics. Note
that these controls (and Balance) will not function when the 6/8 channel direct input is in use.
• To set the output of the AVR so that the output
is “flat,” with the tone and balance controls deactivated, press the Tone Mode button 8 once or twice so that the words Tone Out
appear momentarily in the Main Information
Display ˜. To return the tone controls to an
active condition, press the Tone Mode 8
button once or twice so that the words Tone
I n momentarily appear in the Main
Information Display ˜.
• When the tone controls are active, the amount
of bass and treble boost/cut may be adjusted by
first pressing the Tone Mode Button on the
front panel 8 or the remote two or three
times until the desired setting (BASS MODE
or TREBLE MODE) appears in the on-screen
display and the Lower Display Line ˜. Next,
use the ⁄/¤ Navigation Button E on the
remote or the ‹/ › Button on the front panel
7$ to change the setting as desired. The unit
will return to normal operation within five
seconds after the setting is changed.
• For private listening, plug the 6.3 mm stereo
phone plug from a pair of stereo headphones
into the front panel Headphone Jack 4.
Note that when the headphone’s plug is connected, the speakers will automatically mute and
a two-channel stereo signal will be sent to the
headphones. The Lower Display Line ˜ will
read DOLBY H: B P, indicating that the
headphone output is in the Bypass mode, and to
confirm that no processing is being used.
• When the headphones are in use, you may take
advantage of the Dolby Headphone modes to
bring added spaciousness to headphone listening. Press the Dolby Mode Select Button M
or the Surround Mode Group Selector 5 to
cycle through the three Dolby Headphone modes
to select the one that you prefer.
Surround Mode Selection
One of the most important features of the AVR is
its ability to reproduce a full multichannel
surround sound field from digital sources, analog
matrix surround encoded programs and standard
stereo or even mono programs.
Selection of a surround mode is based on personal
taste, as well as the type of program source
material being used. For example, CDs, motion
pictures or TV programs bearing the logo of one of
the major surround-encoding processes, such as
Dolby Surround should be played in either the
Dolby Pro Logic II Movie (with movies) or Music
(with music) surround mode, with any DTS NEO:6
mode or with Harman Kardon´s exclusive Logic 7
Movie Mode, to create a full range 5.1 channel
or (with Logic 7 and DTS NEO:6) even 7.1
channel surround signal from surround encoded
programs, with a stereophonic left and right rear
signal, just as it was recorded (e.g. sound being
recorded from left rear side will be heard from
that side only, for more details see chart on page
36).
When no rear speakers are in use, the Dolby 3
Stereo mode should be selected with all surround
recordings.
Note that when Dolby Digital 2.0 signals (e.g.
"D.D. 2.0" tracks from DVD), that are encoded
with Dolby Pro Logic information, are received
via any digital input, the Dolby Pro Logic II Movie
mode will be selected automatically (in addition
to the Dolby Digital mode) and will decode a full
range 5.1 channel surround sound even from
those recordings (see also "Dolby Digital" on
page 40).
To create wide, enveloping sound field
environments and defined pans and flyovers with
all analog stereo recordings select the Dolby Pro
Logic II Music or Emulation mode or Harman
Kardon’s exclusive Logic 7 Music mode for a
dramatic improvement in comparison to the
Dolby Pro Logic (I) mode of former times.
NOTE: Once a program has been encoded with
matrix surround information, it retains the
surround information as long as the program is
broadcast in stereo. Thus, movies with surround
sound may be decoded via any of the analog
surround modes such as Pro Logic II Cinema,
Logic 7 Cinema or DTS Neo:6 Cinema, when they
are broadcast via conventional TV stations, cable,
pay-TV and satellite transmission. In addition, a
growing number of made-for-television programs,
sports broadcasts, radio dramas and music CDs
are also recorded in surround sound. You may
view a list of these programs at the Dolby
Laboratories Web site at www.dolby.com.
Even when a program is not listed as carrying
intentional surround information, you may find
that the Dolby Pro Logic II, Dolby Pro Logic IIx,
DTS NEO:6 Music or Logic 7 Music or Enhanced
modes often deliver enveloping surround
presentations through the use of the natural
surround information present in all stereo
recordings.
However, for stereo programs without any
surround information the Theater, Hall and 5/7CH
Stereo modes should be tried (effective particularly
with old ”extreme” stereo recordings) and for
mono programs, we suggest that you try the
Theater or Hall modes.
Surround modes are selected using either the
front panel controls or the remote. To select a
new surround mode from the front panel, first
press the Surround Mode Group Selector
Button 5 until the desired major surround
mode group such as Dolby, DTS or Logic 7 is
selected. Next, press the Surround Mode
Selector Button 9 to choose the specific
individual surround mode.
To select a surround mode using the remote control, press the button for the major surround
mode group that includes the mode you wish to
choose from: Dolby M, DTS Surround N,
DTS Neo:6 , Logic 7 O, Stereo or
DSP Surround A. The first press of the button
will show the current mode from that group if it
is already in use, or the first available mode if you
are currently using another mode. To cycle
through the available modes in that group press
the button again until the desired mode appears
in the Lower Display Line ˜ and the onscreen display.
To select from the DSP modes (Hall 1, Hall 2,
Theater) press the Surround Mode Selector
A repeatedly to scroll through the list of
available modes.
OPERATION 39
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Operation
Operation
Note that the Dolby Digital or DTS modes may
only be selected when a digital input is in use. In
addition, when a digital source is present, the
AVR will automatically select and switch to the
correct mode (Dolby Digital or DTS), regardless of
the mode that has been previously selected. For
more information on selecting digital sources, see
the following section of this manual.
In order to provide maximum playback
compatibility with DVDs, the AVR 445 receiver
will always default first to the playback mode
embedded in a disc’s digital “flag” information.
For Dolby Digital discs, the following playback
modes are initially selected after the AVR locks to
the incoming digital audio data stream to
identify the selected:
When the 6-Channel/8-Channel direct inputs are
in use there is no surround processing, as these
inputs take the analog output signals from an
optional, external DVD-Audio or SACD player, or
another source device and carry them straight
through to the volume control.
• When a 5.1 audio stream is detected, the
Dolby Digital 5.1 format will be selected,
regardless of the number of speakers in your
system, in compliance with Dolby Laboratories
licensing requirements.
To listen to a program in traditional two-channel
stereo, using the front left and front right
speakers only (plus the subwoofer, if installed and
configured), press the Stereo Button 5
until SURR OFF appears in the Main
Information Display ˜.
Digital Audio Playback
Digital audio is a major advancement over older
analog surround processing systems such as
Dolby Pro Logic. It delivers five or six discrete
channels: left front, center, right front, left
surround and right surround and with DTS ES
(see below) even surround back (with identical
signals for left and right). Each channel reproduces full frequency range (20Hz to 20kHz) and
offers dramatically improved dynamic range and
significant improvements to signal-to-noise
ratios. In addition, digital systems have the
capability to deliver an additional channel that is
specifically devoted to low-frequency information. This is the “.1” channel referred to when
you see these systems described as “5.1,” “6.1”
or “7.1”. The bass channel is separate from the
other channels, but since it is intentionally
bandwidth-limited, sound designers have given it
that unique designation.
Dolby Digital
Dolby Digital (originally known as AC-3®) is a
standard part of DVD, and is available on
specially encoded LD discs and satellite broadcasts and it is a part of the new high-definition
television (HDTV) system.
Note that an optional, external RF demodulator
is required to use the AVR to listen to the Dolby
Digital sound tracks available on laser discs.
Connect the RF output of the LD player to the
demodulator and then connect the digital output
of the demodulator to the Optical or Coaxial
inputs *Ó of the AVR. No demodulator
is required for use with DVD players or DTSencoded laser discs.
40 OPERATION
Downloaded from www.Manualslib.com manuals search engine
• When a disc with the Dolby Digital EX format
flag is played, your system will automatically
switch to the EX mode when seven main
channel speakers are available.
• When a disc with Dolby Digital data, but only
2.0 audio is detected, the default mode is
Dolby Digital with Pro Logic II post-processing
when you have a 5.1 speaker system, or
Dolby Digital with Pro Logic IIx post-processing
when you have a 7.1 speaker system.
• Depending on the number of speaker channels
available in your system, once the AVR locks to
the digital signal, you may select any surround
mode or post-processing option that is
available, based on the incoming data stream’s
possible restrictions and the number of
speakers in your system. For example, when a
5.1 or 2.0 audio stream is in use, you may
select alternate postprocessing such as
Logic 7/7-Channel Movie Mode postprocessing to create the rear surrounds in
7.1 speaker systems.
DTS
DTS is another digital audio system that is
capable of delivering 5.1, 6.1 or 7.1 audio.
Although both DTS and Dolby Digital are digital,
they use different methods of encoding the
signals, and thus they require different decoding
circuits to convert the digital signals back to
analog.
DTS-encoded sound tracks are available on select
DVD and LD discs, as well as on special audioonly DTS CDs. You may use any LD, DVD or CD
player equipped with a digital output to play
DTS-encoded special audio-only CDs with the
AVR, but DTS-LDs can be played on LD players
and DTS-DVDs on DVD players only. All that is
required is to connect the player’s digital output
to either the Optical or Coaxial input on the
rear panel or front panel *Ó.
In order to listen to DVDs encoded with DTS
sound tracks, the DVD player must be compatible
with the DTS signal as indicated by a DTS logo
on the player’s front panel. Note that early DVD
players may not be able to play DTS- encoded
DVDs. This does not indicate a problem with the
AVR, as some players cannot pass the DTS signal
through to the digital outputs. If you are in doubt
as to the capability of your DVD player to handle
DTS DVDs, consult the player’s owner’s manual.
Please note that some DVD players are shipped
with their output set for Dolby Digital only. To
insure that DTS data is being sent to the AVR,
please check the setup menu system on your
DVD player to make certain that DTS data output
is enabled.
PCM Audio Playback
PCM (Pulse Code Modulation) is the noncompressed digital audio system used for
compact discs, Non-Dolby Digital/DTS Laserdiscs
and some special PCM encoded DVDs. The digital
circuits in the AVR are capable of high quality
digital-to-analog decoding, and they may be
connected directly to the digital audio output of
your CD/DVD or LD player (LD only for PCM or
DTS programs, for Dolby Digital laser discs an RF
adapter is needed, see ”Dolby Digital” above).
Connections may be made to either the Optical
or Coaxial inputs on the rear panel or the
front panel Digital Inputs *Ó.
To listen to a PCM digital source, first select the
input for the desired source (e.g., CD) to feed its
video signal (if any) to the TV monitor and to
provide its analog audio signal for recording.
Next press the Digital Select button Û G
and then use the ⁄ / ¤ buttons E on the
remote, or the Selector buttons 7$ on the
front panel, until the desired choice appears in the
Lower Display Line ˜, then press the Set
button @ F to confirm the choice.
In most cases this will be 4 8 KHZ, though in
the case of specially mastered, high-resolution
audio discs you will see a 9 6 KHZ indication.
The PCM 4 8 KHZ indication will also appear
when modes or inputs are changed for analog
sources. In those cases the system is telling you
the sampling frequency used internally at the
output of the analog-to-digital converters that
change the incoming signal from a VCR, tape
deck, the tuner, or other ana-log source to
digital.
During PCM playback the unit automatically will
turn to the default surround mode or to the
LOGIC 7 mode but you also may select any
surround mode except Dolby Digital or DTS.
Selecting a Digital Source
To utilize either digital mode you must have
properly connected a digital source to the AVR.
Connect the digital outputs from DVD players,
HDTV receivers, satellite systems or CD players to
the Optical or Coaxial inputs on the rear or
front panel *Ó. In order to provide a
backup signal and a source for analog stereo
recording, the analog outputs provided on digital
source equipment should also be connected to
their appropriate inputs on the AVR rear panel
(e.g., connect the analog stereo audio output
from a DVD to the DVD Audio inputs on
the rear panel when you connect the source’s
digital outputs).
When a digital source is playing, the AVR will
display a variety of messages to indicate the type
of bitstream received. These messages will
appear shortly after an input or surround mode is
changed, and will remain in the Main Information Display ˜ for about five seconds
before the display returns to the normal surround
mode indication.
To select a digital source such as DVD, first select
its input using the remote or front panel Input
Selector 4% as outlined in this manual in
order to feed its video signal (if any) to the TV
monitor and to provide its analog audio signal
for recording. When the digital input associated
with the input selected (e.g. “DVD”) is not
selected automatically (due to the input settings
made earlier during the system configuration, see
page 24), select the digital source by pressing
the Digital Input Selector button G Û and
then using the ⁄/¤ buttons E on the remote
or the Selector buttons 7$ on the front
panel to choose any of the OPTICAL or
COAXIAL inputs, as they appear in the
Upper Display Line ˜ or on-screen display.
• A 3 tells you that separate front left, center
and front right signals are available. This will be
displayed for Dolby Digital 5.1 and DTS 5.1
programs.
When the digital source is playing, the AVR will
automatically detect whether it is a multichannel
Dolby Digital or DTS source, MP3 or conventional
PCM signal, which is the standard output from
CD players.
Note that a digital input (e.g. coaxial) remains
associated with any analog input (e.g. DVD) as
soon as it is selected, thus the digital input need
not be re-selected each time the appropriate
input choice (e.g. DVD) is made.
Digital Bitstream Indicators
When a digital source is playing, the AVR senses
the type of bitstream data that is present. Using
this information, the correct surround mode will
automatically be selected. For example, DTS bitstreams will cause the unit to switch to DTS
decoding, and Dolby Digital bitstreams will enable
Dolby Digital decoding. When the unit senses
PCM data, from CDs and LDs and some music
DVDs or certain tracks on normal DVDs, it will
allow the appropriate surround mode to be
selected manually. Since the range of available
surround modes depends on the type of digital
data that is present, the AVR uses a variety of
indicators to let you know what type of signal is
present. This will help you to understand the
choice of modes and the input channels recorded
on the disc.
For Dolby Digital and DTS sources, a three digit
indication will appear, showing the number of
channels present in the data. An example of this
type of display is 3/2/.1.
The first number indicates how many discrete
front channel signals are present.
• A 2 tells you that separate front left and right
signals are available, but there is no discrete
center channel signal. This will be displayed for
Dolby Digital bit streams that have stereo
program material.
• A 1 tells you that there is only a mono channel
available in the Dolby Digital bitstream.
The middle number indicates how many discrete
surround channel signals are present.
• A "3" tells you that separate, discrete left
surround, center surround and right surround
signals are present. This is available only on
discs with DTS-ES digital audio.
• A 2 tells you that separate surround left and
right signals are available. This will be
displayed for Dolby Digital 5.1 and DTS 5.1
programs.
• A 1 tells you that there is only a single,
surround encoded surround channel. This will
appear for Dolby Digital bit streams that have
matrix encoding.
• A 0 indicates that there is no surround channel
information. This will be displayed for twochannel stereo programs.
The last number indicates if there is a discrete
Low Frequency Effects (LFE) channel. This is the
“.1” in the common abbreviation of “5.1” sound
and it is a special channel that contains only bass
frequencies.
• A .1 tells you that an LFE channel is present.
This will be displayed for Dolby Digital 5.1 and
DTS 5.1 programs, as available.
• A 0 indicates that there is no LFE channel
information available. However, even when
there is no dedicated LFE channel, low
frequency sound will be present at the
subwoofer output when the speaker
configuration is set to show the presence of
subwoofer.
• The information in the right side of the display
will tell you if the digital audio data contains a
special flag signal that will automatically
activate the appropriate 6.1 or 7.1 mode. This
will be shown as EX-ON or EX-OFF for Dolby
Digital bitstreams and ES-ON or ES-OFF for
DTS bitstreams.
When Dolby Digital 3/2/.1 or DTS 3/2/.1 signals
are being played, the AVR will automatically
switch to the proper surround mode, and no
other processing may be selected. When a Dolby
Digital signal with a 3/1/0 or 2/0/0 signal is
detected you may select any of the Dolby
surround modes.
It is always a good idea to check the readout for
the channel data to make certain that it matches
the audio logo information shown on the back of
a DVD package. In some cases you will see
indication for “2/0/0” even when the disc
contains a full 5.1, or 3/2/.1 signal. When this
happens, check the audio output settings for
your DVD player or the audio menu selections for
the specific disc being played to make certain
that the player is sending the correct signal to
the AVR.
USB Playback
The AVR 445 is among the very few A/V receivers
capable of direct connection to a computer for
audio playback. Once the AVR is connected,
audio streams and playback are possible through
your AVR, with all the power and performance of
the high-current amplifier, your own speakers,
and the enhanced multichannel playback made
possible through the use of Logic 7, Dolby
Pro Logic II/IIx or DTS Neo:6 processing.
The AVR’s USB connectivity may be used with
PC-compatible computers running either
Microsoft® Windows® 2000 with Service Pack 4
or higher installed, or Windows XP® or Windows
XP Media Center Edition with Service Pack 1 or
higher installed. Connect one of the available
USB jacks on your computer or a USB hub to the
USB Jack on the AVR using a cable with a
standard USB plug on one side and a USB “Mini
B” plug on the other side.
OPERATION 41
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Operation
Operation
In addition, you will need to have a media player
installed on the computer. The AVR has been
tested for operation with Windows Media Player®
Version 8.0 and above, but it is also compatible
with many other popular players such as iTunes®,
WinAmp® and Real Player®. In most cases, it is
best to always make certain that you have the
latest version of the player installed to ensure the
best compatibility.
When the connection between a computer and
the AVR is made for the first time, or if the USB
connection is plugged into a different USB jack
on a computer or hub that has not been
previously connected to the AVR, you will see a
series of pop-up messages from Windows to
indicate that the computer is configuring itself
for the new device. Since the AVR provides a
number of different functions, you may see the
“Found New Hardware” message up to four
times, one each for “A/V Receiver,” “Compatible
Device,” “Audio Receiver” and “Human Interface
Device.” When all messages have appeared and
then cleared the screen, you are almost ready to
begin.
Before selecting the USB input, first make certain
that one of the media players listed above has
been opened on the computer. Then you may
select the USB input in any of the following
ways:
• To select USB as a source from the front panel,
press the Input Source Selector Button %
until USB appears as the input name in the
Upper Display Line ˜ and in the semi-OSD
display, if available. The USB Input Source
Indicator ˆ will also light up on the front
panel.
• To select USB as the input using the main
remote press the Input Selector 4 with
DMP printed on the button twice.
• To select USB as an input using the ZR 10
remote, press the USB Input Selector D.
When the USB input is selected and the AVR is
connected to a compatible computer with one of
the media players mentioned above open, you
may then use either remote's transport controls
to start and stop playback, as well as move to
the next track. Activity of the Transport buttons
may vary from one media player to another, but
at the very least you will be able to use the Play
and Stop buttons. You may also control the
media player on a connected computer using the
Transport Controls P on the ZR 10 remote.
42 OPERATION
Downloaded from www.Manualslib.com manuals search engine
Once playback is started, the audio from a USB
source is treated the same as any other twochannel audio source, and you may apply any of
the appropriate surround processing modes.
When playing back audio from a computer via
the USB connection, the internal speakers in a
laptop computer are often muted.
Speaker/Channel Indicators
In addition to the Bitstream Indicators, the
AVR features a set of unique channel-input
indicators that tell you how many channels of
digital information are being received and/or
whether the digital signal is interrupted.
These indicators are the L/C/R/LFE/SL/SR/SBL/SBR
letters that are inside the center boxes of the
Speaker/Channel Input Indicators Ú in the
front panel Main Information Display ˜.
When a standard analog stereo or matrix
surround signal is in use, only the “L” and “R”
indicators will light, as analog signals have only
left and right channels.
Digital signals, however, may have one, two, five,
six or seven separate channels, depending on the
program material, the method of transmission
and the way in which it was encoded. When a
digital signal is playing, the letters in these
indicators will light in response to the specific
signal being received. It is important to note that
although Dolby Digital, for example, is referred to
as a “5.1” system, not all Dolby Digital DVDs or
audio tracks selected on DVD or other Dolby
Digital programs are encoded for 5.1. Thus, it is
sometimes normal for a DVD with a Dolby Digital
soundtrack to trigger only the “L” and “R”
indicators.
NOTE: Many DVD discs are recorded with both
“5.1” and “2.0” versions of the same soundtrack. When playing a DVD, always be certain to
check the type of material on the disc. Most discs
show this information in the form of a listing or
icon on the back of the disc jacket. When a disc
does offer multiple soundtrack choices, you may
have to make some adjustments to your DVD
player (usually with the “Audio Select” button or
in a menu screen on the disc) to send a full 5.1
feed to the AVR or to select the appropriate
audio track and thus language. It is also possible
for the type of signal feed to change during the
course of a DVD playback. In some cases the
previews of special material will only be recorded
in 2.0 audio, while the main feature is available
in 5.1 audio. As long as your DVD player is set
for 6-channel output, the AVR will automatically
sense changes to the bitstream and channel
count and reflect them in these indicators.
Important Note: When a digital surround
source (Dolby Digital, DTS) is played, the letters
SBL/SBR for the Surround Back channels will
appear only when a DTS ES DISCRETE 6.1 source
is played. Then this surround mode will be
indicated in the front display and on-screen
display. With all other recordings the icons for the
surround back speakers may light (when those
speakers have been configured) to indicate that a
signal will be fed to them (Matrix decoded with
NEO:6, LOGIC 7 or 7 CH Stereo), but no letters
inside will light as the unit will not receive an
input signal for the surround back channels.
The letters used by the Speaker/Channel Input
Indicators Ú also flash to indicate when a bitstream has been interrupted. This will happen
when a digital input source is selected before the
playback starts, or when a digital source such as
a DVD is put into a Pause mode. The flashing
indicators remind you that the playback has
stopped due to the absence of a digital signal
and not through any fault of the AVR. This is
normal, and the digital playback will resume
once the playback is started again.
Night Mode
A special feature of Dolby Digital is the Night
mode, which enables Dolby Digital input sources
to be played back with full digital intelligibilty
while reducing the maximum peak level and
lifting the low levels by 1/4 to 1/3. This prevents
abruptly loud transitions from disturbing others
without reducing the impact of the digital source.
The Night mode is available only when the Dolby
Digital mode is selected.
The Night mode may be engaged when a Dolby
Digital DVD is playing by pressing the Night
Button B on the remote. Next, press the ⁄/¤
buttons E to select either the middle range or
full compression versions of the Night mode. To
turn the Night mode off, press the ⁄/¤ buttons
E until the message in the lower third of the
video display and the Lower Display Line ˜
reads D-RANGE OFF.
The Night mode may also be selected to always
be on as soon as the Dolby Digital mode is
activated at either level of compression using the
options in the Surround Select menu.
See page 27 for information on using the menus
to set this option.
IMPORTANT NOTES ON DIGITAL PLAYBACK:
• When the digital playback source is stopped, or
in a pause, fast forward or chapter search mode,
the digital audio data will momentarily stop, and
the channel position letters inside the Speaker/
Channel Indicators Ú will flash. This is normal and does not indicate a problem with either
the AVR or the source machine. The AVR will
return to digital playback as soon as the data is
available and when the machine is in a standard
play mode.
• Although the AVR will decode virtually all DVD
movies, CDs and HDTV sources, it is possible that
some future digital sources may not be compatible
with the AVR.
• Note that not all digitally encoded programs
and not all audio tracks on a DVD contain full
5.1 or 6.1 channel audio. Consult the program
guide that accompanies the DVD or laser disc to
determine which type of audio has been
recorded on the disc. The AVR will automatically
sense the type of digital surround encoding used,
indicate it in the Channel Input Indicators Ú
and adjust to accommodate it.
• When a Dolby Digital or DTS source is playing,
you normally may not be able to select some of
the analog surround modes such as Dolby Pro
Logic II, Dolby 3 Stereo, Hall, Theater, 5CH/7CH
Stereo or Logic 7, except with specific Dolby
Digital 2.0 recordings that can be played with
the Pro Logic II modes too (see page 40).
• When a digital source is playing, it is possible
to make an analog recording using the Tape or Video 1 or Video 2 or "& record outputs,
even if the source is connected to any digital
input of the AVR only, as long as "Surround Off"
mode is selected (possible with a PCM source
only). But the analog two channel signal, even of
a Dolby Digital (not DTS) source, the ”Downmix”
to Stereo or Dolby Surround, can be recorded by
connecting its analog audio outputs to the
appropriate analog inputs (e.g. DVD) of the AVR.
Additionally, the digital signals will be passed
through to the Digital Audio Outputs .
Using
The AVR 445 is equipped for use with Harman
Kardon’s optional TheBridge iPod docking
station.
TM
When The Bridge is connected to the AVR and an
iPod properly docked, you may use either remote
to control the iPod for audio playback, while
using the front-panel display and on-screen
semi-OSD messages to help you locate tracks or
view information about the track being played. In
addition, connecting an iPod to the AVR through
The Bridge also charges the iPod’s battery.
Using the DMP AUTO POWER menu option,
as described on page 46, you may even have the
AVR automatically turn on with your iPod as a
playback source whenever the iPod is turned on.
Front Panel In/Outputs
• From the front panel, press the Input Source
Selector 7 on the front panel as needed.
In addition to the rear panel digital outputs, the
AVR offers Harman Kardon’s exclusive
configurable front panel output jack feature.
For easy connection of portable devices, you may
switch the front panel Video 4 jack Ô from an
input to an output by following these steps:
• From the main remote, press the Input DMP
Selector 3.
1. Press the OSD button L to view the
MASTER MENU (Figure 7).
• From the ZR 10 remote, press the /DMP
Selector .
2. Press the Set button F to enter the
IN/OUT SETUP menu (Figure 8).
To select The Bridge as the AVR’s input source:
When The Bridge is connected and a compatible
iPod properly docked, the iPod’s menu will be
replaced with “harman/kardon” at the top of the
iPod’s screen and the front panel display and
semi-OSD message will show messages that will
guide you through the menu and content
selection. If the Lower Display Line ˜ shows
an UNPLUGGED… message, please check to
see that the correct iPod adapter is used in The
Bridge and that the iPod is properly seated.
The AVR’s front-panel controls may also be used
to access a limited number of iPod functions.
Press the Tuner Mode Button ! to play or
pause the current track. The Tuning Selector
) may be used to search in reverse (left side of
button) or forward (right side of button) through
the tracks. Press the Tuner Band Selector !
to call up the iPod’s menu. Press the Preset
Station Selectors # to scroll and the Set
Button @ to select. For complete information
on using the remote or front-panel controls to
operate an iPod, see the instructions that are
included with The Bridge.
Tape Recording
In normal operation, the audio or video source
selected for listening through the AVR is sent to
the record outputs. This means that any program
you are watching or listening to may be recorded
simply by placing machines connected to the outputs for Tape Outputs or Video 1 or 2
Outputs " & in the record mode.
3. Press the ¤ button E so that the on-screen
➞ cursor is next to VIDEO 4.
4. Press either of the ‹ / › buttons E so that
the word OUT is highlighted.
5. Press the OSD button L to exit the menus
and return to normal operation.
Note that once the setting is made, the
appropriate Input/Output Status Indicator
( will turn red, indicating that the selected
analog jacks are now an output, instead of in the
default setting as an input. Once changed to an
output, the setting will remain as long as the
AVR is turned on, unless the setting is changed in
the OSD menu system, as described above. Note,
however, that once the AVR is turned off, the
setting is cancelled. When the unit is turned on
again, the front panel jacks will return to their
normal default setting as an input. If you wish to
use the jacks as an output at a future time, the
setting must be changed again using the OSD
menu system, as described above.
NOTES:
• To make an analog recording from a digital
source is possible, but only from a PCM source
(not Dolby Digital or DTS) and correctly only with
"Surround Off" mode (with any Surround mode
only the L/R front signals will be fed to the record
outputs).
When a digital audio recorder is connected to
any of the Digital Audio Outputs , you are
able to record the digital signal using a CD-R,
MiniDisc or other digital recording system.
Note that all digital signals will be passed
through to both, coaxial and optical, digital
outputs simultanously, no matter which kind of
digital input was selected.
OPERATION 43
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Operation
Operation
Output Level Adjustment
With Source Signals
Normal output level adjustment for the AVR is
established using the test tone, as outlined on
page 34. In some cases, however, it may be
desirable to adjust the output levels using
program material such as a test disc, or a
selection you are familiar with. Additionally, the
output level for the subwoofer and those for the
Stereo modes can only be adjusted using this
procedure. Note that all adjustments made with
any input will be effective with all inputs
selected, just as it is the case with the
adjustment using the test tone.
To adjust the output levels using program
material, first select the surround mode for which
you want to trim the speakers (see NOTE below),
start your program material source and set the
reference volume for the front left and front right
channels using the Volume Control I.
Once the reference level has been set, press the
Channel Select button CÙ and note that
FRONT L LEVEL will appear in the Lower
Display Line ˜. To change the level, first
press the Set button F @, and then use the
Selector buttons 7$ or the ⁄/ ¤ buttons
E to raise or lower the level. DO NOT use the
volume control, as this will alter the reference
setting.
Once the change has been made, press the Set
button F @ and then press the Selector
buttons 7$ or the ⁄/¤ buttons E to
select the next output channel location that you
wish to adjust. To adjust the subwoofer level,
press the Selector buttons 7$ or the ⁄/¤
buttons E until WOOFER LEVEL appears
in the Main Information Display ˜ or onscreen display (only available if the subwoofer is
turned on).
Press the Set button F @ when the name of
the desired channel appears in the Main
Information Display ˜ and on-screen
display, and follow the instructions shown above
to adjust the level.
Repeat the procedure as needed until all
channels requiring adjustment have been set.
When all adjustments have been made and no
further adjustments are made for five seconds,
the AVR will return to normal operation.
The channel output may also be adjusted using
the full-OSD on-screen menu system. First, set
the volume to a comfortable listening level using
the Volume Control ıI. Then, press
the OSD button L to bring up the MASTER
MENU (Figure 7). Press the ¤ Button E four
times until the on-screen ➞ cursor is next to
the MANUAL SETUP line. Press the Set
Button F, select the CHANNEL ADJUST
line and press the Set Button F to activate the
CHANNEL ADJUST menu (Figure 22).
44 OPERATION
Downloaded from www.Manualslib.com manuals search engine
*
CHANNE L ADJU ST
*
FL
: 0dB
SBR : 0dB
→ CEN : 0dB
SBL : 0dB
FR
: 0dB
SL
: 0dB
SR
: 0dB
SW1 : 0dB
TES T TONE : AUTO O FF MAN
LEV EL RES ET: OFF ON
CH ADJUST : GLOB AL
EZS ET SET TINGS: O FF ON
BAC K TO M ANUAL SETUP
Figure 22
When the menu appears, the internal test tone
will be turned off. This will allow you to use your
external test disc or other source material as the
test signal. Then, use the ⁄/¤ Buttons E to
select the channels to be adjusted. At each
channel position use the ‹ / › Buttons E to
change the output level.
Remember, when you are using a disc with test
signal (e.g. pink noise) or an external signal
generator as the source, the goal is to have the
output level at each channel be equal when
heard at the listening position, with any surround
mode selected. When your test source is a normal disc with music signals, you may adjust the
level for each channel and surround mode as you
prefer, e.g. you may lower the center channel
level when you find it to be too high or increase
the level of the rears when you find it to be too
low with specific surround modes.
If you wish to reset all the levels to their original
factory default of 0dB offset, press the ⁄/¤
Buttons E so that the on-screen cursor is
next to the LEVEL RESET line and press
the ‹ / › Buttons E so that the word O N is
highlighted. After the levels are reset, resume the
procedure outlined above to reset the levels to
the desired settings. When all adjustments are
done, press the ⁄/¤ Buttons E to move the
on-screen ➞ cursor so that it is next to BACK
T O MANUAL SETUP and then press the
Set Button F if you wish to go back to the
main menu to make other adjustments. If you
have no other adjustments to make, press the
OSD Button L to exit the menu system.
NOTE: The output levels may be separately
trimmed for each digital and analog surround
mode. If you wish to have different trim levels for a
specific mode, select that mode and then follow the
instructions in the steps shown above.
With Stereo modes the adjustment procedure
described above is the only way to trim the output level, e.g. to match the Stereo level with
other modes.
EzSet/EQ On/Off
If you wish to turn the filter settings established
by EzSet/EQ on or off to demonstrate the impact
EzSet/EQ has on the sound of your system,
simply press the EzSet/EQ On/Off button .
Using this feature does not change the settings;
it merely puts them in or out of the signal path.
Dim Function
Since the AVR will often be used when movies or
other video programming is viewed under lowlight conditions, you may wish to lower the
brightness of the front-panel displays and
indicators so that they do not distract from the
video presentation. You may dim the displays
using the menu system, as shown on page 45, or
you may control the brightness directly from the
remote.
Simply press the Dim Button D once to dim
the front panel to half the normal brightness
level; press it again to turn the displays off. Note
that when the displays are dimmed or turned off,
the blue lighting around the Standby/On
Switch 3 will continue to stay lit as a reminder
that the AVR is still turned on.
The accent lighting for the Volume Control ı
will remain at its normal level, rather than dim
when the panel displays are at half brightness.
Note that all changes to the front-panel
brightness level are temporary; the displays will
return to full brightness after the AVR is turned off
and then on again. To return the displays to full
brightness without turning the unit off, press the
Dim Button D as needed until the displays
are on.
In addition to lowering the brightness of the
displays or turning them off completely, you may
wish to have them appear whenever a button on
the remote or front panel is pushed, and then
gradually fade out after a set time period. You
may do this by making the appropriate settings in
the VFD FADE TIME OUT line of the
ADVANCED SELECT menu, as shown on
page 45.
Memory Backup
This product is equipped with a memory backup
system that preserves tuner presets and system
configuration information if the unit is turned off
completely, accidentally unplugged or subjected
to a power outage. This memory will last for
approximately two weeks, after which time all
information must be reentered.
The AVR is equipped with a number of advanced
features that add extra flexibility to the unit’s
operation. While it is not necessary to use these
features to operate the unit, they provide additional options that you may wish to use.
Front-Panel-Display Fade
In normal operation, the front-panel displays and
indicators remain on at full brightness, although
you may also dim them or turn them off as
shown on page 46. As an additional option, you
may also set the AVR so that the displays are on
whenever a button is pressed on the front panel
or remote, but then fade out after a set period of
time.
To set the front-panel displays to the Fade mode,
press the OSD Button L to bring the
Master Menu to the screen. Press the ⁄/¤
Navigation Button E so that the ➞ cursor
is pointed to the ADVANCED line, and press
the Set Button F to enter the ADVANCED
SELECT menu (Figure 23).
*
→
A D V A N C ED
VFD
FADE
S E L E C T
TIME
OUT:
*
OFF
VFD BRIGHTNESS: FULL
VOLUME DEFAULT: OFF ON
DEFAULT VOL SET: -25dB
SEMI OSD TIME OUT: 2s
FULL OSD TIME OUT: 20s
DMP
BACK
AUTO
TO
POWER:
MASTER
OFF
ON
MENU
Figure 23
With the ADVANCED SELECT menu on
your video display, press the ⁄/¤ Navigation
Button E so that the ➞ cursor is pointed to
the VFD FADE TIME OUT line. Next, press
the ‹ / › Navigation Button E so that the
amount of time that you wish the displays to
fade out after a button is pressed is shown.
Once this time is set and the unit returned to
normal operation, the displays will remain on for
the time period selected whenever a button is
pressed on the front panel or remote. After that
time they will gradually fade out, with the
exception of the lighting surrounding the
Standby/On Switch 3, which remains on to
remind you that the AVR is turned on. Note that
if the displays have been turned completely off
using the Dim Button, as shown on page 46, the
Fade function will not operate.
If you wish to make adjustments to other items
on the ADVANCED SELECT menu, press
the ⁄/¤ Navigation Button E to place the
➞ cursor next to the desired item, or place the
➞ cursor next to the BACK T O MASTER
MENU line and press the Set Button F to
make an adjustment to another menu. If you
have completed all adjustments, press the OSD
Button L to exit the menu system.
Display Brightness
Turn On Volume Level
The AVR’s front panel Main Information
Display ˜ is set at a default brightness level
that is sufficient for viewing in a normally lit
room. However, in some home theater
installations, you may wish to occasionally lower
the brightness of the display, or turn it off
completely.
To change the display brightness setting for a
specific listening session, you will need to make
an adjustment in the ADVANCED SELECT
menu. To start the adjustment, press the OSD
button L to bring the MASTER MENU to
the screen. Press the ⁄ Button E, until the onscreen ➞ cursor is next to the ADVANCED
line. Press the Set Button F to enter the
ADVANCED SELECT menu (Figure 23).
As is the case with most audio/video receivers,
when the AVR is turned on, it will always return
to the volume setting in effect when the unit was
turned off. However, you may prefer to always
have the AVR turn on at a specific setting,
regardless of what was last in use when the unit
was turned off. To change the default condition
so that the same volume level is always used at
turn-on, you will need to make an adjustment in
the ADVANCED SELECT menu. To start
the adjustment, press the OSD button L to
bring the MASTER MENU (Figure 7) to the
screen. Press the ⁄ button E, until the onscreen ➞ cursor is next to the ADVANCED
line. Press the Set button F to enter the
ADVANCED SELECT menu (Figure 23).
To change the brightness setting, at the
ADVANCED SELECT menu, make certain
that the on-screen ➞ cursor is next to the VFD
line, and press the › Button E until the
desired brightness level is highlighted in the
video display. When FULL is highlighted, the
display is at its normal brightness. When HALF
is highlighted, the display is at half the normal
brightness level. When OFF is highlighted, all of
the indicators in the Main Information
Display ˜ will go dark. Note, however, that the
Power Indicator 3, will always remain lit to
remind you that the unit is turned on.
At the ADVANCED SELECT menu make
certain that the on-screen ➞ cursor is next to the
VOLUME DEFAULT line by pressing the
⁄/¤ buttons E as needed. Next, press the ➞
button E so that the word O N is highlighted
in the video display. Next, press the ¤ button
E once so that the on-screen ➞ cursor is next
to the DEFAULT VOL SET line. To set the
desired turn-on volume, press the ‹ / › buttons
E or hold them pressed until the desired volume level is shown on the DEFAULT VOL
SET line. Note that this setting may NOT be
made with the regular volume controls.
If you wish to make other adjustments in the
menu, press the ⁄/¤ Buttons E until the onscreen ➞ cursor is next to the desired setting or
the BACK T O MASTER MENU line and
press the Set button F. If you have no other
adjustments to make, press the OSD Button L
to exit the menu system.
NOTE: Since the setting for the turn-on volume
cannot be heard while the setting is being made,
you may wish to determine the setting before
making the adjustment. To do this, listen to any
source and adjust the volume to the desired level
using the regular volume controls I. When
the desired volume level to be used at turn-on is
reached, make a note of the setting as it appears
in the lower third of the video screen or in the
Main Information Display ˜.
A typical volume level will appear as a negative
number such as -25dB. When making the
adjustment, use the ‹ / › buttons E to enter
this setting.
The display brightness may also be changed by
pressing and holding the Set button @ on the
front for three seconds until the message in the
Main Information Display ˜ reads VFD
FULL. Within five seconds, press the front
panel Selector buttons 7$ until the desired
brightness display level is shown. At that point,
press the Set button @ again to enter the
setting.
Once the desired brightness level is selected, it
will remain in effect until it is changed again or
until the unit is turned off.
Unlike some of the other adjustments in this
menu, the turn-on volume default will remain in
effect even when the unit is turned off
completely, unless it is changed or turned off in
this menu.
If you wish to make other adjustments in the
menu, press the ⁄/¤ Buttons E until the onscreen ➞ cursor is next to the desired setting or
the BACK T O MASTER MENU line and
press the Set button F. If you have no other
adjustments to make, press the OSD Button L
to exit the menu system.
ADVANCED FEATURES 45
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Advanced Features
Advanced Features
Semi-OSD Settings
Full-OSD Time Out Adjustment
The semi-OSD system places one line messages
at the lower third of the video display screen
whenever the Volume, Input Source, Surround
mode or tuner frequency of any of the
configuration settings are changed (except when
HDMI, 720p or 1080i sources are in use).
The semi-OSD system is helpful in that enables
you to have feedback on any control changes or
remote commands using the video display when
it is difficult to view the front-panel displays.
However, you may occasionally prefer to turn
these displays off for a particular listening
session. You may also want to adjust the length
of time the displays remain on the screen. Both
of those options are possible with the AVR.
The FULL OSD menu system is used to
simplify the setup and adjustment of the AVR
using a series of on-screen menus. The factory
default setting for these menus leaves them on
the screen for 20 seconds after a period of
inactivity before they disappear from the screen
or Time Out. This Time Out is a safety measure to
prevent the menu text from burning into the
CRTs in your monitor or projector, which might
happen if they were left on indefinitely. However,
some viewers may prefer a slightly longer or
shorter period before the Time Out display.
To turn off the semi-OSD system, you will need to
make an adjustment in the ADVANCED
SELECT menu (Figure 23). To start the
adjustment, press the OSD button L to bring
the MASTER MENU to the screen. Press the
⁄ Button E, until the on-screen ➞ cursor is
next to the ADVANCED line. Press the Set
Button F to enter the ADVANCED
SELECT menu.
At the ADVANCED SELECT menu make
certain that the on-screen ➞ cursor is next to the
SEMI OSD line by pressing the ⁄/¤ buttons
E as needed. Next, press the › button E so
that the word OFF is highlighted in the video
display.
Note that this setting is temporary and will
remain active only until it is changed or until the
AVR is turned off. Once the unit is turned off, the
semi-OSD displays will remain activated, even if
they were switched off for the previous listening
session.
To change the length of time that the semi-OSD
displays remain on the screen, go to the
ADVANCED SELECT Menu as outlined
earlier, and press the ⁄/¤ buttons E as
needed, until the on-screen ➞ cursor is next to
the SEMI-OSD TIME OUT line. Next,
press the ‹/› Buttons E until the desired time
in seconds is displayed. Note that unlike most of
the other options in this menu, this is a
permanent setting change, and the time-out
entry will remain in effect until it is changed,
even when the unit is turned off.
If you wish to make other adjustments in the
menu, press the ⁄/¤ Buttons E until the onscreen ➞ cursor is next to the desired setting or
the BACK T O MASTER MENU line and
press the Set button F. If you have no other
adjustments to make, press the OSD Button L
to exit the menu system.
46 ADVANCED FEATURES
Downloaded from www.Manualslib.com manuals search engine
To change the Full-OSD Time Out, you will need
to make an adjustment in the ADVANCED
SELECT menu (Figure 23). To start the
adjustment, press the OSD button L to bring
the MASTER MENU to the screen. Press the
⁄ button E, until the on-screen ➞ cursor is
next to the ADVANCED line. Press the Set
Button F to enter the ADVANCED
SELECT menu (Figure 23).
At the ADVANCED SELECT menu make
certain that the on-screen ➞ cursor is next to the
FULL OSD TIME OUT line by pressing the
⁄/¤ Buttons E as needed. Next, press the
‹ / › buttons E until the desired time is
displayed in seconds. Note that unlike most of
the other options in this menu, this is a
permanent setting change, and the time-out
entry will remain in effect until it is changed,
even when the unit is turned off.
If you wish to make other adjustments in the
menu, press the ⁄/¤ Buttons E until the
on-screen ➞ cursor is next to the desired setting
or the BACK T O MASTER MENU line and
press the Set button F. If you have no other
adjustments to make, press the OSD Button L
to exit the menu system.
DMP/ TheBridge
TM
Auto Power
When using Harman Kardon’s optional TheBridge
iPod docking station, the normal operation is to
have the iPod selected as the input source only
when it is specifically chosen. However, you may
set the AVR so that whenever the iPod is turned
on, the AVR will also turn on automatically and
set The Bridge as the input.
TM
To change the setting, first make certain that the
ADVANCED SELECT menu (Figure 23) is
on the screen, and then press the ⁄/¤
Navigation Buttons EF until the cursor is
pointing to DMP AUTO POWER. Press the
⁄/¤ Navigation Buttons EF so that O N
is highlighted to have the AVR turn on in sync
with an iPod, or OFF for standard operation.
Multiroom Operation
The AVR is fully equipped to operate as the
control center for a complete multiroom system
that is capable of sending one source to a
second zone in the house while separate source
is listened to in the main room. In addition to
providing for control over the selection of the
remote source and its volume, the AVR offers a
comprehensive range of options for powering the
speakers in the second zone.
• Using the line-level Multiroom Audio
Outputs , the selected source may be fed to
optional, external power amplifiers that may be
matched to the specifics of the installation.
• When the main room system is configured for
5.1 operation, the Surround Back Left/Right
amplifier channels may be used to power the
remote zone so that no additional amplifiers are
required.
• Using built-in A-BUS/READY technology,
optional A-BUS modules may be connected to
the AVR via a single Category Five wire, so that
remote zone speakers may be powered directly
from the module or keypad without the need for
additional power, IR sensor or volume control
wires to be run to the second zone.
®
In addition, the AVR includes a remote IR sensor
input so that remote control commands from the
Zone II remote included with the unit may be
transmitted to the unit, while standard IR
input/output jacks allow the remote zone’s
commands to be sent to compatible IR-controlled
source devices.
For installations where A-BUS modules are used,
follow the instructions provided with the A-BUS
remote modules or keypads.
Additional information will also be made available through the Harman Kardon Web Site at
www.harmankardon.com.
At the MULTI I N line, press the ‹/› buttons
E until the desired Audio/Video input to the
multi-room system appears in the highlighted
video. When the selection has been made, press
the ¤ button E once so that the ➞ on-screen
cursor is next to the MULTI VOL line.
RS-232 Control
At the MULTI VOL line, press the ‹ / ›
buttons E or hold them pressed until the
desired volume level for the multi-room system is
entered. DO NOT use the regular volume control
knobs for this setting. When all settings for the
multiroom setup have been made, press the
¤ buttons E once so that the on-screen ➞
cursor is next to the BACK T O MASTER
MENU line and press the Set button F. If you
have no other adjustments to make, press the
OSD button L to exit the menu system.
The AVR is rare among A/V receivers in that it
provides the capability for full remote control
from compatible computers or specialized remote
control systems. RS-232 programming requires
specialized programming knowledge and for that
reason we recommend that it only be done by
qualified installers.
NOTE: The RS-232 port on this product is
for use by authorized service personnel
ONLY.
For more information on using the RS-232 port
for remote control, visit the Harman Kardon
Web site at
www.harmankardon.com
or contact our customer service department.
Multiroom Setup
Once the audio and IR link connections have
been made, the AVR needs to be configured for
multiroom operation using the steps below. Press
the OSD button L to bring the MASTER
M E N U (Figure 7) to the screen. Press the ⁄
button E twice, until the on-screen ➞ cursor is
next to the MULTI-ROOM line. Press the Set
button F to enter the MULTI-ROOM
menu (Figure 24).
*
Installation
Although simple remote room systems may be
installed by the average do-it-yourself hobbyist,
the complexity of your multizone/multiroom
system involves running wires inside of walls
where the services of a specially trained installer
may be required. Regardless of who does the
work, please remember that local building codes
may govern in-wall electrical work, including
proper specification of any wiring used and the
way in which it is connected. You are responsible
for making certain that all Multiroom installation
work is done properly and in compliance with all
applicable codes and regulations.
For standard installations, follow the instructions
shown on page 16 and 20 for the connection of
speaker wire and IR remote wiring to the AVR.
For installations where the Surround Back
Left/Right amplifier channels are used to power
the remote zone, make certain that the system is
configured for that type of operation, as shown
on this page.
→
MULTI-ROOM
MULTI-ROOM
MULTI IN
MULTI VOL
SB AMPS
CARRIER OUT
BACK
TO
SETUP
*
:OFF ON
:FM PRESET01
:25dB
:MAIN MULTI
:
ZONE II
MASTER
MENU
Figure 24
When the MULTI-ROOM menu appears, the
on-screen ➞ cursor will be at the MULTIROOM line. Since this line is used to turn the
system on and off, do not make an adjustment
here unless you wish to turn the system on at
this time. To turn the system on, press the
› button E so that O N is highlighted. If you
do not wish to turn the system on at this time or
to proceed to the next step, press the ¤ Button
E once so that the ➞ on-screen cursor is next
to the MULTI I N line.
Surround Amplifier Channel Assignment
The AVR is equipped with seven full-power
amplifier channels to allow for complete
7.1-channel operation without the need for
additional external amplifiers. However, in some
installations you may wish to use the traditional
5.1-channel configuration for the main listening
room, which allows the surround back left/right
amplifier channels to be used to power speakers
placed in a remote zone location.
If you wish to use the Surround Back channel
amplifiers to power the remote zone, you must
change a setting in the MULTIROOM
SETUP menu. To make that change, first call
up the menu system by pressing the OSD
Button L to bring the MASTER MENU
(Figure 7) to the screen. Next, press the ¤
Button E until the ➞ cursor is next to the
MULTI ROOM line. Press the Set Button
F to enter the MULTIROOM SETUP
menu.
To change the setting so that the Surround Back
amplifiers are fed by the source selected through
the Multiroom system, press the ‹ / › Buttons
E so that MULTI is highlighted in reverse
video and press the Set Button F.
Remember that once this setting is made you will
not be able to take advantage of any of the
6.1/7.1- channel decoding or processing modes,
and no Surround Back speakers must be selected
in the speaker setup procedure outlined earlier. In
addition the speakers used for the remote zone
must be connected to the Surround Back/
Multiroom Speaker Outputs . The volume
for these speakers is set by the multiroom
system, as explained on page 48 of this manual.
MULTIROOM OPERATION 47
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Multiroom Operation
Multiroom Operation
Infrared Output Selection
The AVR 445 enables you to select which IR
input will be used to feed the Full Carrier IR
Output ,. The factory default setting is the IR
signal that is fed to the Multiroom IR Input
, but you may select other options.
To change this setting, first make sure the
MULTI-ROOM SETUP menu is on the
screen, and then press the ⁄/¤ Navigation
Buttons EF so that the cursor is next to
CARRIER OUT; then press the Set Button
FQ. Press the ⁄/¤ Navigation Buttons
EF to select one of these options:
• Z R 1 0 feeds the signal present at the
Multiroom IR Input to the Full Carrier
IR Output ,.
• A-BUS feeds the signal carried back from an
optional A-Bus module connected to the AVR
to the Full Carrier IR Output ,.
• FRONT feeds the received through the frontpanel Remote Sensor Window ¯ to the
Full Carrier IR Output ,.
When all needed adjustments to the MULTIROOM SETUP menu have been made, press
the ⁄/¤ Navigation Buttons EF until
the cursor is pointing to BACK T O MASTER
MENU to make changes to other menus, or
press the OSD Button L E to exit the
menu system and return to normal operation.
Multiroom Operation
When operating the AVR from a remote room
location where an IR sensor link has been connected to the AVR’s rear panel Multiroom IR
Input , you may use either the Main remote
control or the ZR 10 remote buttons BC
D. Press the AVR Selector B to turn the
unit on to the last source, or any of the other
Selector buttons to turn on to a specific source.
With the remote pointing toward an IR sensor or
A-Bus module in the remote room, you may turn
on the second zone system by pressing the AVR
Selector Button B on the ZR 10 remote to
turn the system on with the last used source for
the multiroom system active, or you may press
one of the Input Selectors D or the Tuner
Selector C or TheBridge Selector to
turn the multiroom system on directly to a
specific source.
To turn the system off from the remote room,
press the Power-Off button 0A. Remember
that the AVR may be turned on or off from the
remote room regardless of the system’s operation
or status in the main room.
NOTE: When the tuner is selected as the source
for the remote zone, any change to the frequency
or preset will also change the station being listened to in the main room, if the tuner is in use
there. Similarly, if someone in the main room
changes the station, the change will also impact
the remote room.
To activate the feed to the remote room, press
the Multiroom button on the remote.
Next, press the Set button F.
When the MULTI ON/OFF message
appears in the on-screen display and the Lower
Display Line ˜, press the Set Button F
and then press the ⁄/¤ Navigation Button
E so that display changes to MULTI O N.
Press the Set Button F again to activate the
setting. Note that this method may be used to
turn the Multiroom system on or off even when
the AVR is in the Standby mode in the main listening room.
IMPORTANT NOTE: When an A-BUS module is
connected, the AVR’s Multiroom system must be
turned on before the A-BUS module is able to
communicate with the AVR. Once turned on
using the instructions in the preceding paragraph, the Multiroom system must remain on in
order for the A-BUS module to operate.
When the unit is in the Standby mode, but ready
for Multiroom or A-BUS operation, the lighting
around the Standby/On Switch 3 remains
blue and a MULTI O N message appears in the
Lower Display Line ˜, even though the unit
is “off” in the main listening room.
When the multiroom system is turned on, the
input selected using the Multiroom Menu will be
fed to the Multiroom Output jacks on the
rear panel as well as the A-BUS Jack .
The volume will be as set in the same menu,
although it may also be adjusted using an optional IR sensor and the Zone II remote in the remote
location or on the optional audio power amplifier
connected to the Multiroom Output jacks .
TM
When the multiroom system is turned on, you
may use the same buttons on either remote that
would normally be used to control an AVR
function such as volume, source selection, tuner
control or the operation of an iPod docked to The
Bridge. If any of the input devices are connected
to the IR Output or Full Carrier IR Output
,, by either a hard-wire connection or through
an optional IR “blaster,” you may use the
Transport Controls P on the ZR 10 to
operate compatible Harman Kardon products.
48 MULTIROOM OPERATION
Downloaded from www.Manualslib.com manuals search engine
Although changes to the input source or remote
room volume will normally be made using an IR
sensor in the remote room that is connected to
the AVR, it is also possible to change those
settings from the main listening room. This is
useful for situations where some or all of the
remote rooms do not have an IR sensor, or to
take control over the remote room without
actually being in that room.
In addition to using the MULTIROOM menu,
as shown on the previous page, you may change
the source or volume in the remote zone using
the remote. Press the Multiroom Button on the remote, and when the MULTI
ON/OFF message appears in the on-screen
display and the Lower Display Line ˜, press
the Set Button F and then press the
⁄ / ¤ Navigation Button E to toggle past
that message to MULTI LEVEL or
MULTI INPUT.
To change the remote room’s input source,
when MULTI INPUT appears, press the
Set Button F, and then press the ⁄ / ¤
Navigation Button E until the desired input
appears in the on-screen display and in the
Lower Display Line ˜. Remember that only
analog or PCM input sources may be selected for
use with the Multiroom system. Dolby Digital or
DTS sources are not available to the Multiroom
system.
To change the remote room’s volume, when
MULTI LEVEL appears, press the Set
Button F, and press the ⁄ / ¤ Navigation
Button E to change the volume setting. Note
that this volume adjustment controls the level for
the output to the Multiroom Audio Outputs
and for any speakers connected to the
Surround Back/Multiroom Speaker Outputs
' when the Surround Back amplifier channels
are configured for Multiroom use, as shown on
page 47. This adjustment does NOT change the
volume level for any room where an ABUS
module is used, as that setting is only adjustable
using the A-BUS module’s volume control or
built-in IR sensor.
Once the multiroom system is turned on, it will
remain on even if the AVR is placed in the
Standby mode in the main room by pressing the
Power Off Button 0 or the System Power
Control 2 on the front panel. To turn off the
multiroom system from the main listening room,
when the AVR is on press the Multiroom button
and then the Set button F. Press the
⁄ / ¤ buttons E so that the Main
Information Display ˜ or OSD will display
MULTI OFF.
Even when the AVR is turned off (to Standby
mode) and the multiroom system is turned off
too, the multiroom system may be turned on at
any time by pressing the Multiroom button
, or any of the Selector buttons
BCD in the remote room.
Basic Tuner Operation
The AVR’s tuner is capable of tuning AM, FM and
FM Stereo broadcast stations and receiving RDS
data. Stations may be tuned manually, or they
may be stored as favorite station presets and
recalled from a 30 position memory.
Station Selection
1. Press the AM/FM Tuner Select button 6
on the remote to select the tuner as an input. The
tuner may be selected from the front panel by
either pressing the Input Source Selector %
until the tuner is active or by pressing the Tuner
Band Selector ! at any time.
2. Press the AM/FM Tuner Select button 6
or Tuner Band Selector ! again to switch
between AM and FM so that the desired
frequency band is selected.
3. Press the Tuner Mode button I on the
remote or hold the Band Selector ! on the
front panel pressed for 3 seconds to select
manual or automatic tuning.
When the button is pressed so that AUTO
appears in the Main Information Display ˜
each press of the Tuning Selectors )K will
put the tuner in a scan mode that seeks the next
higher or lower frequency station with
acceptable signal strength. An AUTO S T
TUNED indication will momentarily appear
when the station stops at a stereo FM station,
and an AUTO TUNED indication will
momentarily appear when an AM or monaural
FM station is tuned. Press the Tuning buttons
again to scan to the next receivable station.
When the button is pressed so that MANUAL
appears in the Main Information Display ˜
each tap of the Selector will increased or
decrease the frequency by one increment. When
the tuner receives a strong enough signal for
adequate reception, MANUAL TUNED will
appear in the Main Information Display ˜.
4. Stations may also be tuned directly by pressing
the Direct button J, and then pressing the
Numeric Keys H that correspond to the
station’s frequency. Note that for entering
numbers higher than 100 you need to enter only
the "1" rather than "10", the first "0" will be
added automatically. The desired station will
automatically be tuned after the latest number is
entered. If you press an incorrect button while
entering a direct frequency, press the Clear
button to start over.
NOTE: When the FM reception of a stereo
station is weak, audio quality will be increased
by switching to Mono mode by pressing the
Tuner Mode button I on the remote or
holding the Band Selector ! on the front
panel so that MANUAL appears momentarily in
the Main Information Display ˜ and then
goes out.
Preset Tuning
Using the remote, up to 30 stations may be
stored in the AVR’s memory for easy recall using
the front panel controls or the remote.
To enter a station into the memory, first tune the
station using the steps outlined above. Then:
1. Press the Memory button on the remote.
Note that two underscore lines will appear in the
Main Information Display ˜.
2. Within five seconds, press the Numeric
Keys H corresponding to the location where
you wish to store this station’s frequency. Once
entered, the preset number will appear in the
Main Information Display ˜.
3. Repeat the process after tuning any additional
stations to be preset.
Recalling Preset Stations
• To manually select a station previously entered
in the preset memory, press the Numeric Keys
H that correspond to the desired station’s
memory location.
• To manually tune through the list of stored
preset stations one by one, press the Preset
Stations Selector buttons # on the front
panel or remote.
RDS Operation
The AVR is equipped with RDS (Radio Data
System), which brings a wide range of
information to FM radio. Now in use in many
countries, RDS is a system for transmitting station
call signs or network information, a description
of station program type, text messages about the
station or specifics of a musical selection, and
the correct time.
As more FM stations become equipped with RDS
capabilities, the AVR will serve as an easy-to-use
center for both information and entertainment.
This section will help you take maximum
advantage of the RDS system.
RDS Tuning
When an FM station is tuned in and it contains
RDS data, the AVR will automatically display the
station’s call sign or other program service in the
Main Information Display ˜.
RDS Display Options
The RDS system is capable of transmitting a
wide variety of information in addition to the
initial station call sign that appears when a
station is first tuned. In normal RDS operation
the display will indicate the station name,
broadcast network or call letters. Pressing the
RDS button ^ enables you to cycle
through the various data types in the following
sequence:
• The station’s call letters (with some private
stations other information too).
• The station’s frequency (FREQ).
• The Program Type (PTY) as shown in the list
below.
NOTE: Many stations do not transmit a specific
PTY. The display will show NONE, when such a
station is selected and PTY is active.
• A “text” message (Radiotext, R T) containing
special information from the broadcast station.
Note that this message may scroll across the
display to permit messages longer than the eight
positions in the display. Depending on signal
quality, it may take up to 30 seconds for the text
message to appear; in that time, the word
TEXT will flash in the Information Display when
RT is selected.
• The current time of day (C T). Note that it may
take up to two minutes for the time to appear, in
that time the word TIME will flash in the
information display when CT is selected. Please
note that the accuracy of the time data is
dependent on the radio station, not the AVR.
Some RDS stations may not include some of
these additional features. If the data required for
the selected mode is not being transmitted, the
Main Information Display ˜ will show a
N O TYPE, N O TEXT or N O TIME
message after the individual time out.
In any FM mode the RDS function requires a
strong enough signal for proper operation.
TUNER OPERATION 49
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Tuner Operation
Tuner Operation
Program Search (PTY)
An important feature of RDS is its capability of
encoding broadcasts with Program Type (PTY)
codes that indicate the type of material being
broadcast. The following list shows the
abbreviations used to indicate each PTY, along
with an explanation of the PTY:
• (RDS ONLY)
• (TRAFFIC)
• NEWS: News
• AFFAIRS: Current Affairs
• INFO: Infomation
• SPORT: Sports
• EDUCATE: Educational
• DRAMA: Drama
• CULTURE: Culture
• SCIENCE: Sciencek
• VARIED: Varied Speech Programs
• POPM: Popular Music
• ROCKM: Rock Music
• M.O.R.M.: Middle-of-the-Road Music
• LIGHTM: Classical Music
• CLASSICS: Serious Classical Music
• OTHERM: Other Music
• WEATHER: Weather Information
• FINANCE: Financial Programs
• CHILDREN: Children’s Programs
• SOCIAL A: Social Affairs Programs
• RELIGION: Religious Broadcasts
• PHONE IN: Phone-In Programs
• TRAVEL: Travel and Touring
• LEISURE: Leisure and Hobby
• JAZZ: Jazz Music
• COUNTRY: Country Music
• NATIONAL: National Music
• OLDIES: Oldies Music
• FOLK M: Folk Music
• DOCUMENT: Documentary Programs
• TEST: Emergency Test
• ALARM: Emergency Broadcast Information
50 TUNER OPERATION
Downloaded from www.Manualslib.com manuals search engine
You may search for a specific Program Type (PTY)
by following these steps:
1. Press the RDS button ^ until the
current PTY is shown in the Main
Information Display ˜.
2. While the PTY is shown, press the Preset
Up/Down button # or hold them
pressed to scroll through the list of available
PTY types, as shown above starting with the
PTY currently received. To simply search for
the next station transmitting any RDS data,
use the Preset Up/Down button #
until RDS ONLY appears in the display.
3. Press any of the Tuning Up/Down buttons
)K, the tuner begins to scan the FM band
upwards or downwards for the first station
that has RDS data that matches the desired
selection, and acceptable signal strength for
quality reception.
4. The tuner will make up to one complete scan
of the entire FM band for the next station that
matches the desired PTY type and has
acceptable reception quality. If no such
station is found, the display will read NONE
for some seconds and the tuner will return to
the last FM station in use before the search.
NOTE: Some stations transmit constant traffic
information. These stations can be found by
selecting TRAFFIC, the option in front of
NEWS in the list. The AVR will find the next
appropriate station, even if it is not broadcasting
traffic information when the search is made.
Configuring the Remote
The AVR 445 remote is factory-programmed for
all functions needed to operate the unit. In
addition, it is also preprogrammed to operate
most recent Harman Kardon DVD players and
changers, CD players and changers, CD recorders
and cassette decks. The codes for other brand
devices may be programmed into the AVR 445
remote using its extensive library of remote codes
or a head-to-head learning process for codes not
in the internal library.
For this example, we will select “TV” to enter the
codes needed to operate your TV.
SELECT A DEVICE
TV
Figure 27
NOTE: The codes for hard-drive recorder
products (PVR) such as TiVo and Replay are
programmed by selecting VCR as the device. For
satellite-based TiVo products, check under the
brand name of the product.
Thanks to the remote’s advanced technology and
two-line LCD display, it is no longer necessary to
look up cumbersome codes when programming
the remote; following the steps outlined below,
you simply search for the brand name from the
remote’s memory. We recommend that you first
try the preprogrammed code entry method. If
that procedure is not successful, then try the
code learning method.
5. At the next menu screen on the remote (Figure
28) press the Set Button F to enter the
Manual mode, which means that you will
select the brand name of the device from the
list programmed into the remote’s memory.
Preprogrammed Code Entry
6. The next menu screen on the remote (Figure
19) will show the start of the list of available
brands. Press the ⁄¤ Navigation Buttons
E until the brand name of the device you
are programming into the remote appears on
the lower line of the display and then press
the Set Button F.
The easiest way to program the AVR remote for
operation with a source device from another
brand is to follow these steps:
1. Turn on the power to the device you wish to
program into the AVR remote. This is
important, as in a later step you will need to
see whether the device turns off to determine
whether the remote has been programmed for
the proper remote codes.
2. Press and hold the Program Button for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display 2. Release the
button when the red light under the Set
Button F appears.
HOLD PROG BUTTON
FOR 3 SECONDS
Figure 25
3. The remote’s MAIN MENU message (Figure
26), will appear in the LCD display and the
Set Button F will remain illuminated in
red. Press the Set Button F to begin the
process of selecting a device and locating the
proper remote codes.
MAIN MENU
PROGRAM DEVICE
Figure 26
4. SELECT A DEVICE will appear in the LCD
display (Figure 27).
Press the ⁄¤ Navigation Buttons E to
scroll through the list of device categories and
press the Set Button F when the device
you wish to set the codes for appears.
PROGRAM DEVICE
MANUAL
Figure 28
SELECT BRAND
RCA
Figure 29
NOTE: If the brand name for the product you
wish to program does not appear in the list, the
codes may still be available, as some manufacturers share codes. If the desired brand is not listed,
press the Clear Button to exit the programming process, and skip to the instructions
shown on page 52 for the “Automatic” method
of programming the remote. If desired, or if the
codes for your brand are not part of the remote’s
library at all, you may still use the AVR remote to
program most infrared-controlled products by
“learning” the commands from the product’s
original remote into the AVR remote. The instructions for Learning Commands are on page 52.
7. The next step is important, as it determines
which codes will operate the source device or
display. Point the AVR remote at the device
being programmed and, following the
instructions shown in the remote’s LCD
Information Display 2, press and release
the Numeric Keys H shown on the menu
screen (Figure 30) one at a time, starting with
the “1” button. After you press the “1”
Button H, the remote’s LCD screen will
briefly go blank as the code is being transmitted, but you will see the “transmit” icon
in the upper right corner of the display to
serve as confirmation that the remote is
sending out commands.
PRESS A NUMBER
CODE 1 OF 10
Figure 30
8. After you press and release the number key,
watch the device being programmed to see
whether it turns off. As shown in the instructions that will appear on the next menu screen
(Figure 31), if your device has turned off, press
the Set Button F, and then skip to Step
10. If the unit does not turn off, proceed to the
next step.
POWER OFF? Y:SET
N: NEXT# OR CLR
Figure 31
9. If the device being programmed into the AVR
remote does not turn off after you have
pressed the “1” key, continue Steps 8 and 9 by
pressing the available numeric keys shown
until the device turns off. If the device still does
not turn off after all choices have been tried,
or if there is only one number key shown as
available to try, the code for this specific
device is not in the AVR remote library under
that brand name. If that is the case, press the
Clear Button to exit the manual programming mode. Remember that the codes
may still be stored in the AVR remote’s library
under another brand, and you can have the
remote control search for them by following
the instructions below for automatic programming. You may also manually “learn” the
codes for most devices into the AVR remote by
following the Learning Commands instructions
on page 52.
10. When the device being programmed does
turn off after a numeric key has been
pressed, you must press the Set Button F
within five seconds to enter the setting into
the remote’s memory. After you press the Set
button, the top line of the LCD display will
read SAVING… and then the word SAVED
will flash four times in the center of the
bottom line.
11. When the codes are saved the remote will
return to normal operation, and whenever
you press the Input Selector Button 4
that was just programmed, the codes for the
new device will be used. If no further buttons
are pressed, the remote will revert back to
the default setting for AVR commands.
NOTE: Some brands share a common remote
control code for “Power Off” for many models.
For that reason it is possible that even though
the remote appears to be properly programmed,
you may find that some buttons do not appear to
issue the correct command. If this is the case,
repeat the procedure outlined above, but if more
than one numeric key selection is suggested in
Step 7, try a different number to see whether the
remote operates correctly.
PROGRAMMING THE REMOTE 51
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Programming the Remote
Programming the Remote
Although the AVR remote is preprogrammed with
an extensive library of codes for many major
brands, it is also possible that you may have
attempted to program a product that is too new
or too old, and thus not all of its commands will
be in the code library. You may fill in the codes
for any button that does not operate properly by
using the learning technique shown on page this
page.
Automatic Code Entry
In addition to manual code selection using the
brand name list, it is also possible to automatically search through all the codes that are stored
in the AVR remote’s library to see whether a
device will respond even if it is not listed among
the brands that appear when you program the
remote manually. To automatically search
through the codes that are available for a specific
device type (e.g., DVD, VCR), follow these steps:
1. Turn on the power to the device you wish to
program into the AVR remote. This is important, as in a later step you will need to see
whether the device turns off to determine
whether the remote has been programmed for
the proper remote codes.
2. Press and hold the Program Button for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display 2. Release the button when the red light under the Set Button
F appears.
3. The remote’s MAIN MENU message (Figure
26) will appear in the LCD display and the Set
Button F will remain illuminated in red.
Press the Set Button F to begin the
process of selecting a device and locating the
proper remote codes.
You will also see the transmit icon in the upper
right corner of the LCD display’s top line to
remind you that the remote is working even
though you may not see anything happening to
the device being programmed.
7. It will take a few seconds for the remote to
send out the first group of commands, after
which you will see a new display in the LCD
screen, as shown in Figure 33. Following the
instructions, if the device being programmed
has NOT turned off, press the ⁄ Navigation
Buttons E again to send another group of
codes. If the device being programmed has
turned off, skip to Step 9.
POWER OFF?
Y-> 1~0 N->
Figure 33
8. By pressing the ⁄ Navigation Buttons E
again, the remote will send out a new set of
commands. When it pauses, follow the instructions shown in Step 7. Depending on how
many codes are stored for a specific device
type, you may have to repeat this process as
many as fifteen times. Remember, if the device
turns off, skip to Step 9. When all the codes for
the device being programmed have been tried,
the instruction shown in Figure 34 will appear.
This means that the codes for the product you
are trying to program are not in the AVR
remote library and you will have to “learn”
them into the remote following the
instructions shown on this page. Press the
Set Button F as instructed to exit the
programming process.
REACH END POINT
EXIT -> SET KEY
Figure 34
4. SELECT A DEVICE will appear in the
LCD display (Figure 27).
Press the ⁄¤ Navigation Buttons E to
scroll through the list of device categories and
press the Set Button F when the device
for which you wish to set the codes appears.
For this example, we will select “TV” to enter
the codes needed to operate your TV.
9. If the device being programmed does turn off
after following the instructions in Step 7, you
will need to verify the code set by pressing the
Numeric Keys H in sequence, as instructed
in Figure 33. Point the remote at the device
being programmed, and press the “1” Button
H to see whether the device turns back on.
5. At the next menu screen on the remote (Figure
28), press the ⁄ Navigation Buttons E
so that the bottom line of the LCD display
reads AUTO (Figure 32) and then press the
Set Button F to enter the Automatic programming mode.
10. After pressing and releasing the “1” Button
H, check to see whether the device has
turned back on. If it has, skip to Step 12. If it
does not turn on, press the “2” Button H,
or the next button in the numeric sequence if
you are repeating the procedure, as
instructed by the LCD screen in Figure 35.
PROGRAM DEVICE
AUTO
Figure 32
6. As instructed on the next menu screen, press
the ⁄ Navigation Buttons E to begin
the automatic code search process. Your confirmation that the remote is sending out commands is the movement of a square block
across the top line of the LCD display screen
while the bottom line reads PLEASE WAIT….
52 PROGRAMMING THE REMOTE
Downloaded from www.Manualslib.com manuals search engine
POWER ON?
Y->SET N->1~0
Figure 35
11. When pressing the “1” button does not turn
the device being programmed back on,
repeat the procedure by trying the remainder
of the Numeric Keys H in sequence, each
time pressing and then releasing the button
to see whether the new device turns back on.
When it does, skip to the next step. However,
if you try all 10 numeric keys and find that
the unit will not turn on, you won’t be able
to use this method to program the device.
Press the Clear Button to exit the
programming process. You’ll need to follow
the Learning Commands instructions below
to enter the codes for this device into the
AVR remote.
12. When pressing one of the numeric keys in
Step 10 or 11 causes the device being
programmed to turn back on, follow the
instructions shown in Figure 32 and press the
Set Button F within five seconds of the
device turning on. After you press the Set
button, the top line of the LCD display will
read SAVING… and then the word SAVED
will flash four times in the center of the
bottom line.
13. When the codes are saved, the remote will
return to normal operation, and whenever
you press the Input Selector Button 4
that was just programmed, the codes for the
new device will be used. If no further buttons
are pressed, the remote will revert back to
the default setting for AVR commands.
Learning Commands
On occasions when the AVR remote does not
contain the codes for a particular product’s
remote in its built-in library, or when you wish to
program a missing or special function into one
button of a device, the AVR remote’s learning
capability allows you to do that. To teach
commands from one product’s remote into the
AVR remote, follow these steps:
The process requires that both the device’s
original remote and the AVR remote be available.
Before pressing any buttons on either remote,
place them so that the IR transmitter on the
remote from the device to be programmed is
facing the Infrared Lens 1 on the AVR’s
remote. The two remotes should be no more than
an inch apart, and there should not be any direct
sunlight or other bright light source near the
remotes.
1. Press and hold the Program Button for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display 2. Release the
button when the red light under the Set
Button F appears.
2. The remote’s MAIN MENU message (Figure
26), will appear in the LCD display and the
Set Button F will remain illuminated in
red. Press the ⁄ Navigation Buttons E
once so that Learn appears on the bottom line
of the LCD screen, as shown in Figure 36.
Press the Set Button F to begin the
process of learning commands from another
device’s remote into the AVR remote.
MAIN MENU
LEARN
Figure 36
3. The SELECT A DEVICE message will appear
in the LCD display (Figure 27). Press the ⁄¤
Navigation Buttons E to scroll through
the list of device categories and press the Set
Button F when the device for which you
wish to set the codes appears. For this example, we will select “TV” to enter the codes
needed to operate your TV.
4. The next menu screen (Figure 37) will prompt
you to select the button, or “key,” on the AVR
remote that you wish to program. Press that
button on the AVR remote.
SELECT A KEY
TO PROGRAM
Figure 37
5. Once you press the button to be programmed
on the AVR remote, press and hold the button
on the remote control for the device to be
programmed within five seconds, as instructed
on the next menu screen (Figure 38).
PRESS KEY ON
ORIGINAL REMOTE
Figure 38
6. Continue to hold the button on the original
remote until the menu on the AVR remote’s
LCD screen changes. If the code is successfully
learned you will see the display shown in
Figure 39. If you see that menu, proceed to
Step 9. If the code is not successfully learned,
you will see the display shown in Figure 40.
If that menu appears, proceed to Step 7.
LEARN MENU
LRN ANOTHER KEY
Figure 39
LEARN FAILED
RETRY
Figure 40
7. If the message shown in Figure 36 appears in
the display, press the Set Button F to try
programming the button again. When the
remote prompts you to press and hold the key
on the original remote again by showing the
display shown in Figure 38, immediately press
the button on the source remote again. To
avoid another failed attempt, make certain
that the windows on the two remotes are
facing one another.
8. Continue to hold the button on the original
remote until the AVR’s display changes again.
If the code was successfully learned, you will
see the display shown in Figure 35. In that
case, skip to the next step. If the LEARN
FAILED display (Figure 40) appears again
you may either try to program the key again,
or press the ⁄ Navigation Buttons E to
stop the process. It is possible that some
remotes may use code sequences or infrared
frequencies that are not compatible with the
AVR remote, and those codes cannot be
learned. When the display shown in Figure
41 appears, press the Set Button F to
exit the Learning system.
LEARN FAILED
EXIT
Figure 41
9. When a code has been learned successfully,
you have three options. When the display
shown in Figure 39 is on the LCD screen on
the AVR remote, you may press the Set
Button F to learn additional codes from
the buttons on a remote into the AVR
remote. Follow Steps 4 through 8 as often as
needed to complete the code-learning
process.
10. If you wish to change the name that appears
in the LCD display when the button that has
just had a new code learned is pressed, press
the ⁄ Navigation Buttons E so that the
display shown in Figure 42 appears in the LCD
display. Press the Set Button F to open
the RENAME KEY menu. Enter the new
name for the key following the instructions
shown in the Renaming Individual Keys section of this manual on page 57. If you find it
more convenient to rename the buttons at
a later time, you may do that separately by following the instructions on page 58.
LEARN MENU
RENAME KEY
Figure 42
11. When you have programmed all keys for the
desired device, press the ⁄ Navigation
Buttons E twice when the LEARN MENU
(Figure 39) appears so that you see the display show in Figure 43. The remote will
return to normal operation.
LEARN MENU
END LEARNING
Figure 43
Learning Codes for an Input
Selector
The AVR 445’s remote allows you to learn a
specific code to be attached to one of the Input
Selectors 4 so that whenever that button is
pressed, you will not only be selecting that
device as the AVR’s input and telling the remote
to use the remote codes that have been programmed to belong to that device, it also allows
you to have that special code transmitted, as
well. This allows you to have an input (or other
command) sent to a display so that when video
sources are directly connected to the display, you
can automatically command it to switch to the
same input selected for the AVR.
To learn a remote code into one of the Input
Selectors 4, follow the same steps shown
above for learning the keys for an entire device
remote with the following exceptions:
• In Step 3, press the ⁄/¤ Navigation
Button E until LEARN DEVICE
appears in the bottom line of the LCD display.
• When the SELECT A DEVICE message
(Figure 36) appears, as described in Step 4,
press the specific Input Selector Button 4
that you wish to have transmit a special code
when it is pressed.
• When the RENAME DEVICE option is
offered by the remote after the code is programmed, you will be changing the name that
is shown in the remote’s LCD display every
time that Input Selector is pressed.
Device Priority
After having programmed or learnt the different
sources, you can set the Device Priority. The
default setting is that after pressing one of the
Input Selectors and any of its function keys, the
remote control defaults back to controlling the
AVR functions after 6 seconds. You can either
extend this time to 12 seconds, or leave the
remote control to control the last used source, by
following the steps below.
1. Press and hold the Program Button until the MAIN MENU appears.
2. Press the ¤ Navigation Button E until
DEVICE PRIORITY appears. Press the Set
Button F.
3. Press the ⁄/¤ Navigation Button E to
select the requested setting. Confirm the
setting by pressing the Set Button F.
12. If you wish to program the codes for another
device, repeat the procedure outline above,
but select a different device in Step 3.
PROGRAMMING THE REMOTE 53
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Programming the Remote
Programming the Remote
Changing Devices
In the factory default settings, the AVR remote is
programmed so that the commands transmitted
correspond to the device selected by pressing
one of the Input Selectors 4. This is logical,
as you want the remote to control the device you
have selected. However, in some circumstances
you may have configured your system so that the
devices connected to the AVR do not correspond
to the default device settings and the legends
printed on the remote. For example, if your system has two VCRs you may connect the second
VCR to the VID 2 input. There is no problem in
doing that, but in normal operation the commands issued after selecting the VID 2 input are
for a television, not a VCR.
The AVR remote allows you to correct that situation through the “Changing Devices” process.
That enables you to assign the codes from one
type of device to a different button. For example,
in the steps below, we will explain how to program the VID 2 buttons to provide the commands
to operate a VCR. Of course, you may program
the remote to have any of the devices take on
the code set of any other device, as your system
requires. And, with the AVR remote’s “Rename”
function, you can even change the way the name
of the device appears on the remote’s LCD display so that you see exactly which commands are
being sent.
To program the buttons normally assigned to one
device for the commands of another, follow these
steps:
1. Press and hold the Program Button for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display 2. Release the button when the red light under the Set Button
F appears.
2. The remote’s MAIN MENU message (Figure
26), will appear in the LCD display and the
Set Button F will remain illuminated in
red. Press the ⁄ Navigation Buttons E
twice so that CHANGE DEVICE appears on
the bottom line of the LCD screen, as shown in
Figure 44. Press the Set Button F to begin
the process of reassigning the commands used
for a particular device.
MAIN MENU
CHANGE DEVICE
Figure 44
3. The next menu display is where you select the
Input Select, or device, that you wish to
change. When the display shown in Figure 45
appears, press the ⁄¤ Navigation
Buttons E to scroll through the list to find
the device you wish to use for another function. In this case we will select “TV,” and show
how to change it to take on the codes for
operating a VCR. When that device’s name
appears, press the Set Button F.
54 PROGRAMMING THE REMOTE
Downloaded from www.Manualslib.com manuals search engine
OLD DEVICE TYPE
TV
Figure 45
4. Once the “old” device type has been selected,
you need to tell the remote which set of
remote codes to use as a replacement for the
device just selected. When the instructions
shown in Figure 46 appear, press the ⁄¤
Navigation Buttons E to scroll through
the list of device categories to find the name
of the device that you wish to use. The old
device name will remain on the left side of the
LCD screen, while the replacement device list
will scroll to its right. For example, press the
⁄ Navigation Buttons E until the display
screen reads TV<-VCR to have the VID 2/TV
Button transmit the commands used to control
a VCR. Press the Set Button F when the
desired device combination appears.
NEW DEVICE TYPE
TV<-VCR
Figure 46
5. Once the new device is selected, the remainder of the process will select the codes for the
specific brand to be used, and for that reason
they are identical to the way a device is programmed using manual entry. Continue the
process as outlined in the next few steps,
remembering that if the codes for your specific
device are not found you may select any brand
and then “learn” the proper codes into the
AVR remote using the process outlined on
page 52. To begin the process, start by selecting the brand of device, as shown in Figure 29.
Press the ⁄¤ Navigation Buttons E
until the brand name of the device you are
programming into the remote appears on the
lower line of the display and then press the
Set Button F.
6. The next step is important, as it determines
which codes will operate the source device or
display. Point the AVR remote at the device
being programmed and, following the instructions shown on the remote’s LCD
Information Display 2, press and release
the Numeric Keys H one at a time, starting with the “1” button. After you press the
“1” Button H the remote’s LCD screen will
briefly go blank as the code is being transmitted, but you will see the “transmit” icon in the
upper right corner of the display to serve as
confirmation that the remote is sending out
commands.
7. After you press and release the number key,
watch the device being programmed to see
whether it turns off. As shown in the instructions that will appear on the next menu screen
(Figure 31), press the Set Button F, and
then skip to Step 9. If the unit does not turn
off, proceed to the next step.
8. If the device being programmed into the AVR
remote does NOT turn off after you have
pressed the “1” key, continue Steps 6 and 7 by
pressing the available numeric keys shown
until the device turns off. If the device still does
not turn off after all choices have been tried,
the code for this specific device is not in the
AVR remote library under that brand name. If
that is the case, we suggest that you press the
Set Button F to accept the codes from
another brand so that the programming is
completed, but remember that you will then
have to program the remote manually by
following the Learning Commands instructions
on page 52.
9. When the device being programmed does
turn off after a numeric key has been
pressed, you must press the Set Button F
within five seconds to enter the setting into
the remote’s memory. After you press the Set
button, the top line of the LCD display will
read SAVING... and then the word SAVED
will flash four times in the center of the bottom line.
10. When the codes are saved the remote will
return to normal operation, and whenever
you press the Input Selector Button 4
that was just programmed, the display will
show the original device type code at the far
left side of the display, with the name of the
new code set type in brackets. For example,
the display will read TV<-VCR in our example of replacing the TV codes with those for a
VCR.
Macro Programming
Macros enable you to easily repeat frequently
used combinations of multiple remote control
commands with the touch of a single button.
Once a macro is programmed you may send up
to 20 commands with one press of the Power On
or Macro buttons. This will greatly simplify the
process of turning on your system, changing
devices or other common tasks. Thanks to the
remote’s two-line display, it is easier than ever
for you to take advantage of the power of macro
commands.
Recording a Macro
To record a macro into the remote’s memory,
follow these steps:
1. Press and hold the Program Button for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display 2. Release the
button when the red light under the Set
Button F appears.
2. The remote’s MAIN MENU message (Figure
26), will appear in the LCD display and the
Set Button F will remain illuminated in
red. Press the ⁄ Navigation Buttons E
three times so that MACRO appears on the
bottom line of the LCD screen, as shown in
Figure 47.
Press the Set Button F to enter the main
macro menu branch.
MAIN MENU
MACRO
Figure 47
3. At the next menu screen (Figure 48) press the
Set Button F to begin recording a macro.
MACRO
RECORD A MACRO
Figure 48
4. The next display screen (Figure 49) is where
you select the button that will be used to
recall the macro. The choices are the Power
On Button 3 or one of the discrete Macro
Buttons . Press the ⁄¤ Navigation
Buttons E until the name of the button
you wish to program the macro into is shown.
For this example we will show how to program
a series of commands that will automatically
be sent out every time the Power button is
pressed.
RECORD A MACRO
POWER ON
Figure 49
5. The next screen that appears (Figure 50) is
where you select the device for the first command that will be sent out as part of the
macro. Press the ⁄¤ Navigation Buttons
E until the name of the device appears on
the left side of the lower line in the LCD display. For this example, the first button we want
to have the macro “press” is the Power On
button, so the AVR device is selected. Press the
Set Button F when the desired device
name appears to move to the next programming step.
SELECT A DEVICE
AVR
Figure 50
6. The next display (Figure 51) is where you
begin entering the individual commands for
the macro, in the order you wish them to be
transmitted. Remember that when you want to
change devices, you must first press the Input
Selector 45 for that button, and then
press the Command or Function key. Since we
want to program a series of events that occur
each time the Power On button is pressed,
press the AVR button. In your specific macro,
this is the first command button.
SELECT A DEVICE
AVR
Figure 51
7. The next display (Figure 52) and the subsequent screens are where the actual macro
programming take place. The words at the left
side of the top line of the display show the
button that is being programmed (e.g., the
Power On Button 3 or one of the Macro
Buttons ) and the indication at the right
side of the top line shows the number of
macro steps available of 20 possible steps.
Following the instructions on the remote’s LCD
screen, press the first key you wish to be transmitted in the macro. In our example, we first
want the AVR to turn on, so the Power
Button 3 should be pressed.
POWER ON
00/20
SELECT KEY PRESS
Figure 52
8. Once the first command button for the macro
has been pressed, continue to press the buttons you wish to be part of the macro, in the
order they will be used. Press each button
within five seconds of the last button, remembering to press the Input Selector 45
when you are changing device functions.
As the buttons on the remote are pressed,
the remote’s display screen will show the steps
in the macro as they are programmed (Figure
53).
[AVR]
[AVR] POWER ON
Figure 53
9. For our example, we first want the AVR Power
On button pressed, followed by the TV Power
On, followed by the Cable Box On, followed by
the selection of the Logic 7 mode. To do that,
press the buttons in this order:
• Power On 3
• VID 2/TV 4
• Power On 3
• VID 3/Cable 4
• Power On 3
• AVR 5
• Logic 7 O
As each button is pressed to enter it into the
macro you will see the button names appear
and then scroll up on the LCD display as your
confirmation of the key entry (Figure 53).
10. When all commands for the macro have been
entered, press the Set Button F to save
the macro. The display screen will show the
button to which the macro has been programmed and the number of steps used, and
the word SAVED will blink four times in the
lower line of the LCD display. When the display returns to normal, the macro has been
entered and the remote is ready for operation.
11. If a macro has been programmed into the
Power On Button 3, it will play back
anytime the Power On button is pressed. As
the macro plays, you will see the steps
appear in the remote’s LCD display. Macros
programmed into one of the four discrete
Macro buttons may be activated at any time
by pressing the appropriate button.
Erasing a Macro
Once a macro has been created and stored in the
AVR remote’s memory, you have the option of
erasing it. You may do this at any time by following these steps:
1. Press and hold the Program Button for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display 2. Release the button when the red light under the Set Button
F appears.
2. The remote’s MAIN MENU message (Figure
26), will appear in the LCD display and the
Set Button F will remain illuminated in
red. Press the ⁄ Navigation Buttons E
three times so that MACRO appears on the
bottom line of the LCD screen, as shown in
Figure 47. Press the Set Button F to enter
the main macro menu branch.
3. At the next menu screen (Figure 54) press
⁄¤ Navigation Buttons E until the bottom line in the remote’s LCD display reads
ERASE A MACRO, as shown in Figure 54.
Press the Set Button F to begin the
process of erasing a macro.
MACRO
ERASE A MACRO
Figure 54
4. The next display screen (Figure 55) is where
you select which macro will be erased. Press
the ⁄¤ Navigation Buttons E until the
number of the macro you wish to erase
appears. For this example we will erase the
Power On macro created in the previous section. When the name of the macro to be
erased appears, press the Set Button F.
ERASE A MACRO
POWER ON
Figure 55
5. The word ERASED will flash four times in the
bottom line of the remote’s LCD display, and
then the display will return to its normal condition. When that happens the macro is erased
and the remote is returned to normal operation.
Read a Macro
To check the commands stored in the remote’s
memory for one of the buttons, follow these
steps:
1. Press and hold the Program Button for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display 2. Release the button when the red light under the Set Button
F appears.
2. The remote’s MAIN MENU message (Figure
26), will appear in the LCD display and the
Set Button F will remain illuminated in
red. Press the ⁄ Navigation Buttons E
three times so that MACRO appears on the
PROGRAMMING THE REMOTE 55
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Programming the Remote
Programming the Remote
bottom line of the LCD screen, as shown in
Figure 47. Press the Set Button F to enter
the main macro menu branch.
3. At the next menu screen (Figure 56) press the
⁄¤ Navigation Buttons E until the bottom line in the remote’s LCD display shows
READ A MACRO, as shown in Figure 56.
Press the Set Button F to begin the
process of erasing a macro.
MACRO
READ A MACRO
Figure 56
4. The next display screen (Figure 57) is where
you select the macro to be read. Press the
⁄¤ Navigation Buttons E until the
name of the macro you wish to read appears.
For this example, we will read back the Power
On macro created in the previous section.
When the name of the macro to be erased
appears, press the Set Button F.
READ A MACRO
POWER ON
Figure 57
5. As soon as the Set button is pressed, the first
two steps in the macro will be appear in the
remote’s LCD screen. You may then use the
⁄¤ Navigation Buttons E to step up or
down through the list of commands stored as
the macro. As you read the display, you will
see Device Selector Buttons 45
appear in brackets, (e.g., [AVR]). When the
step in the macro is a function, navigation or
any other button, it will appear next to the
bracketed read-out of the underlying device
(e.g., [AVR] POWER ON).
6. When you are finished reviewing the macro’s
contents, press the Set Button F to return
the remote to normal operation.
Punch-Through Configuration
Punch-through is a capability of the remote that
allows the Volume controls, Channel Up/Down
buttons or Transport keys (Play, Stop, Record, Fast
Forward and Reverse, and Skip Up/Down) to link
to a different device. For example, if your TV,
cable box or satellite receiver is connected
through the AVR you will most likely want to use
the AVR’s volume control commands even when
the remote has been set to issue all other commands for the video device. “Punch-through”
enables you to easily program the remote to do
this.
Volume Punch-Through
Follow these steps to enable the Volume
Up/Down and Mute controls from one device to
be used when the remote is otherwise programmed for a different device.
Note for Volume Punch-Through:
The remote’s default settings are for the AVR’s
volume controls to be used when any input or
device is selected with the exception of the VID
56 PROGRAMMING THE REMOTE
Downloaded from www.Manualslib.com manuals search engine
2/TV button. There is no need to program the
remote for volume punch-through for the AVR’s
controls with other sources, such as DVD. To have
the AVR’s volume commands used when the TV
device is selected, follow these steps:
1. Press and hold the Program Button for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display 2. Release the button
when the red light under the Set Button F
appears.
2. The remote’s MAIN MENU message (Figure
26), will appear in the LCD display and the
Set Button F will remain illuminated in
red. Press the ⁄¤ Navigation Buttons
E until PUNCH-THROUGH appears on the
bottom line of the LCD screen, as shown in
Figure 58. Press the Set Button F to enter
the main punch-through menu branch.
MAIN MENU
PUNCH-THROUGH
Figure 58
3. At the next menu screen (Figure 59) press the
Set Button F to begin programming the
remote for Volume punch-through.
PUNCH-THROUGH
VOLUME
Figure 59
4. The next display screen (Figure 60) is where
you select the device that will receive the
punch-through commands. In our example,
that is the VID 2/TV button, as that is where
we want the AVR’s volume controls to be
active. Press the ⁄¤ Navigation Buttons
E until the name of the base device appears
and then press the Set Button F.
DEVICE IN USE
TV
Figure 60
5. At the next display screen (Figure 61), you will
select the device whose Volume Up/Down and
Mute commands will be used. Press the ⁄¤
Navigation Buttons E until the desired
device’s name appears to the right of the
device in use. In our example, that is the AVR
(indicated by AVR). When the desired
combination of devices appears, press the Set
Button F.
PUNCH-THROUGH
TV<-AVR
Figure 61
6. When the Set button is pressed, the display
will change to show you that the new combination of control commands is being saved to
the unit’s memory, as shown in Figure 62. The
word SAVED will flash four times and then
the remote will return to normal operation.
TV<-AVR [VOL]
SAVED
Figure 62
7. Once the punch-through is programmed, the
Volume Up/Down and Mute buttons of the
second device named will be used when those
buttons are pressed while the master
device is in use.
Returning the Volume Control Settings to
Default Operation:
If you wish to remove the Volume punch-through
so that the commands for Volume and Mute are
returned to the factory default setting, follow the
steps shown above, except that in Steps 4 and 5,
select the same device for both the DEVICE IN
USE on the left side of the bottom line and the
PUNCH-THROUGH device. In the example used,
the display to return the remote to default settings will appear as shown in Figure 63.
PUNCH-THROUGH
TV<-TV
Figure 63
Channel Punch-Through
Channel punch-through allows the Channel
Up/Down buttons to send commands to a different device than the one that has been selected
for other commands. For example, you may wish
to use a cable box or satellite receiver as the
source for a VCR, so you would want the
Channel Up/Down Selectors to transmit
commands to the cable box even though the
other button commands are programmed to
operate the VCR.
To program the AVR for Channel punch-through,
follow these steps. This example will show how
to program channel punch-through so that the
commands programmed for Channel Up/Down
for the VID 3/ Cable device will be transmitted
when the VID 1/VCR device has been selected as
the current device.
1. Press and hold the Program Button for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display 2. Release the button when the red light under the Set Button
F appears.
2. The remote’s MAIN MENU message (Figure
26), will appear in the LCD display and the
Set Button F will remain illuminated in
red. Press the ⁄¤ Navigation Buttons
E until PUNCH-THROUGH appears on the
bottom line of the LCD screen, as shown in
Figure 58. Press the Set Button F to enter
the main punch-through menu branch.
3. At the next menu screen, press the ⁄¤
Navigation Buttons E until CHANNEL
appears on the bottom line of the LCD screen,
as shown in Figure 64. Press the Set Button
F to begin programming the remote for
Channel punch-through.
PUNCH-THROUGH
CHANNEL
Figure 64
4. The next display screen (Figure 65) is where
you select the device that will receive the
punch-through commands. In our example,
that is the VID 1/VCR button, as that is where
we want the cable box’s channel controls to
be active. Press the ⁄¤ Navigation
Buttons E until the name of the base
device appears and then press the Set
Button F.
DEVICE IN USE
VCR
Figure 65
5. At the next display screen (Figure 66), you will
select the device whose Channel Up/Down
commands will be used. Press the ⁄¤
Navigation Buttons E until the desired
device name appears to the right of the device
in use. In our example, that is the cable box.
When the desired combination of devices
appears, press the Set Button F.
PUNCH-THROUGH
VCR<-CBL
Figure 66
6. When the Set button is pressed, the display
will change to show you that the new combination of control commands is being saved to
the unit’s memory, as shown in Figure 67. The
word SAVED will flash four times and then
the remote will return to normal operation.
VCR<-CBL [CHAN]
SAVED
Figure 67
7. Once the punch-through is programmed, the
channel up/down buttons of the second device
named will be used when those buttons are pressed while the master device is in use.
Returning the Channel Control Settings to
Default Operation:
If you wish to remove the Channel PunchThrough so that the commands for Channel
Up/Down are returned to the factory default setting, follow the steps shown above, except that
in Steps 4 and 5, select the same device for both
the DEVICE IN USE on the left side of the bottom line and the PUNCH-THROUGH device. In
the example used, the display to return the
remote to default settings will appear as shown
in Figure 68.
PUNCH-THROUGH
VCR<-VCR
Figure 68
Transport Punch-Through
Transport punch-through allows the Play P,
Stop P, Fast Forward/Reverse P, Pause
P, Record P and Skip Up/Down buttons to send commands to a different device
than the one that has been selected for other
commands. For example, you may wish to operate the transport of a second VCR you have connected to the VID 2/TV input, as shown in the
following example.
1. Press and hold the Program Button for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display 2. Release the button when the red light under the Set Button
F appears.
2. The remote’s MAIN MENU message (Figure
26), will appear in the LCD display and the
Set Button F will remain illuminated in
red. Press the ⁄¤ Navigation Buttons
E until PUNCH-THROUGH appears on the
bottom line of the LCD screen, as shown in
Figure 58. Press the Set Button F to enter
the main punch-through menu branch.
3. At the next menu screen, press the ⁄¤
Navigation Buttons E until TRANSPORT appears on the bottom line of the LCD
screen, as shown in Figure 69. Press the Set
Button F to begin programming the
remote for transport punch-through.
PUNCH-THROUGH
TRANSPORT
Figure 69
4. The next display screen (Figure 70) is where
you select the device that will receive the
punch-through commands. In our example,
that is the TV button, as that is where we want
the VCR’s transport controls to be active. Press
the ⁄¤ Navigation Buttons E until the
name of the base device appears and then
press the Set Button F.
DEVICE IN USE
TV
Figure 70
5. At the next display screen (Figure 71), you will
select the device whose transport commands
will be used. Press the ⁄¤ Navigation
Buttons E until the desired device name
appears to the right of the device in use. In our
example, that is the VCR. When the desired
combination of devices appears, press the Set
Button F.
PUNCH-THROUGH
TV<-VCR
Figure 71
6. When the Set button is pressed, the display
will change to show you that the new combination of control commands is being saved to
the unit’s memory, as shown in Figure 72.
The word SAVED will flash four times and then
the remote will return to normal operation.
TV<-VCR [TRS]
SAVED
Figure 72
7. Once the punch-through is programmed, the
transport buttons of the second device named
will be used when those buttons are pressed
while the master device is in use.
Returning the Transport Control Settings
to Default Operation:
If you wish to remove the Transport PunchThrough so that the transport commands are
returned to the factory default setting, follow the
steps shown above, except that in Steps 4 and 5,
select the same device for both the DEVICE IN
USE on the left side of the bottom line and the
PUNCH-THROUGH device. In the example used,
the display to return the remote to default settings will appear as shown in Figure 73.
PUNCH-THROUGH
TV<-TV
Figure 73
Renaming
While the names given to the buttons and inputs
on the AVR represent recognizable categories of
audio/ video products, system operation may be
easier if the displays shown in the remote’s LCD
screen are customized to reflect the specific characteristics of a playback source’s brand name or
the new function given to a specific button when
one remote’s controls are programmed into the
AVR remote. The AVR remote allows you to
change the name of either a master device or
any button on the remote using the following
steps.
Renaming a Device
To rename a specific device/input source button,
follow these steps. For this example, we will
show you how to rename the Device/Input
Selector normally shown as “TV” to “HDTV
TUNER.”
1. Press and hold the Program Button for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display 2. Release the button when the red light under the Set Button
F appears.
2. The remote’s MAIN MENU message (Figure
26), will appear in the LCD display and the
Set Button F will remain illuminated in
red. Press the ⁄¤ Navigation Buttons
E until RENAME appears on the bottom
line of the LCD screen, as shown in Figure 74.
MAIN MENU
RENAME
Figure 74
PROGRAMMING THE REMOTE 57
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Programming the Remote
Programming the Remote
3. At the next menu screen press the ⁄¤
Navigation Buttons E until RENAME
DEVICE appears on the bottom line of the
LCD screen, as shown in Figure 75. Press the
Set Button F to begin renaming a device.
RENAME
RENAME DEVICE
Figure 75
4. The next display screen (Figure 76) is where
you select the device that will be renamed. In
our example, that is the TV button. Press the
⁄¤ Navigation Buttons E until the
name of the base device appears and then
press the Set Button F.
RENAME DEVICE
TV
Figure 76
5. At the next menu screen you will see the
device name on the bottom line of the display
with a blinking cursor box to the right of the
device name. Press the ‹ Navigation
Buttons E to return the blinking cursor to
the far left side of the display line. You may
then retitle the device name as shown in the
next step.
6. To enter the new name, press the Numeric
Keys H. The letters above the numbered
buttons indicate which letter or symbol will
appear when the button is pressed during the
renaming process. The first press of the button
will enter the first letter shown, subsequent
presses of the same button will change the
display to the other letters above that numbered key. For example, since the first letter we
need to rename the input to HDTV Tuner is an
“H”, you would locate the “H” above the “4”
button, and press the button twice. The first
press shows a “G,” the second press changes
it to an “H.” Consult the table at the end of
this section to see which characters pressing a
particular button generates.
7. After you enter the first letter of the new
device name, there are three options for entering the next character:
a. To enter a letter that requires a different
numeric key to be pressed, simply press that
button. The cursor will automatically move
to the next position and the first letter
accessed by the new button will appear.
Following our example, the next letter needed is a “D,” so you would press the “3”
button once.
b. To enter a letter that uses the same numeric
key, you must first press the › Navigation
Buttons E to move the blinking cursor
block to the next position. Then press the
Numeric Key H as required to enter the
desired letter.
c. To enter a blank space, press the ›
Navigation Buttons E twice. The first
press will move the cursor to the right, and
58 PROGRAMMING THE REMOTE
Downloaded from www.Manualslib.com manuals search engine
the second press will move the cursor one
more space to the right, leaving a blank
space between the last letter and the next
one.
8. Repeat Step 7 as needed to enter all the
needed letters, numbers, characters and
spaces.
9. When the text entry is complete, press the
Set Button F. The LCD display will blink
DEVICE RENAMED three times and then
return to normal operation.
Once a device is renamed you will see the new
name on the top line of the remote’s LCD display
whenever the Input/Device Selector 4 is
pressed, or when any other command/function
button on the remote is pressed after the main
Device Selector is pressed. Note that renaming a
device in the remote will not change the name of
the input used by the on-screen menu system of
the AVR.
Notes on Renaming Devices:
• To move the cursor to the right or left of the
display during the renaming process, press the
‹ / › Navigation Buttons E as required.
• The table below shows the letters, numbers
and characters that may be accessed by pressing the Numeric Keys:
Key
1
2
3
4
5
Characters
[,],/,1
A,B,C,2
D,E,F,3
G,H,I,4
J,K,L,5
Key
6
7
8
9
0
Characters
M,N,O,6
P,Q,R,S,7
T,U,V,8
W,X,Y,Z,9
-,.,#,0
• Renaming a device changes the name of the
device only, not any of the individual key functions within that device memory. To change the
name of an individual device, follow the
instructions in the next section.
Renaming Individual Keys
Thanks to the programming flexibility of the AVR
remote, an individual button on the remote may
be assigned a feature or function that is different
from the name that appears as the factory
default when the button is pressed. However,
with the Rename Key function it is possible to
rename almost any button on the remote so that
when the button is pressed you will see a more
descriptive or appropriate name displayed.
To rename a specific button on the remote, follow these steps. For this example, we will show
you how to rename the Tone Control Button
, which is normally not used when DVD is
selected so that it reads ZOOM in the remote’s
display.
1. Press and hold the Program Button for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display 2. Release the button when the red light under the Set Button
F appears.
2. The remote’s MAIN MENU message (Figure
26), will appear in the LCD display and the
Set Button F will remain illuminated in
red. Press the ⁄¤ Navigation Buttons
E until RENAME appears on the bottom
line of the LCD screen, as shown in Figure 74.
3. At the next menu screen press the ⁄¤
Navigation Buttons E until RENAME
KEY appears on the bottom line of the LCD
screen, as shown in Figure 77. Press the Set
Button F to continue.
RENAME
RENAME KEY
Figure 77
4. The next display screen (Figure 78) is where
you select the device within which the key to
be renamed exists. Press the ⁄¤
Navigation Buttons E until the name of
the base device appears. In our example, since
we want to rename a button within the DVD
device memory, DVD should appear in the
lower line of the LCD. When the desired device
name appears, press the Set Button F.
SELECT A DEVICE
DVD
Figure 78
5. At the next menu screen you will select the
first button within the device to be renamed,
as instructed in the display shown in Figure
79. Select the button by simply pressing it on
the remote.
SELECT A KEY
Figure 79
6. Depending on whether or not the button
pressed already has a named function within
the device selected, one of two things will
happen.
a. If the button to be renamed already has a
pre-programmed, or previously renamed
title in the remote’s memory, you will see
that name on the top line of the LCD display, and a blinking block cursor will appear
on the far left side of the bottom line of the
display, as shown in Figure 80.
b. If the button to be renamed does not have a
function in the device selected, the top line
of the LCD screen will be blank, and a blinking block cursor will appear on the far left
side of the bottom line of the display, as
shown in Figure 81.
DISC SKIP
Figure 80
Figure 81
7. To enter the new name for the key, press the
Numeric Keys H. The letters above the
numbered buttons indicate which letters or
symbols will appear when the button is
pressed during the renaming process. The first
press of the button will enter the first character shown, subsequent presses of the same
button will change the display to the other letters above that numbered key. For example,
since the first letter we need to rename the
Tone button to Zoom is a “Z,” so you would
locate the “Z” above the “9” button, and
press the button four times. The first press
shows a “W,” the subsequent presses step
through the other letters available until the
“Z” appears. Consult the table on the previous
page to see which characters are available by
pressing a particular button.
8. After you enter the first letter of the new
device name, there are three options for
entering the next character:
a. To enter a letter that requires a different
numeric key to be pressed, simply press that
button. The cursor will automatically move
to the next position and the first letter
accessed by the new button will appear.
Following our example, the next letter needed is an “O,” so you would press the “6”
button once.
b. To enter a letter that uses the same numeric
key, you must first press the › Navigation
Buttons E to move the blinking cursor
block to the next position. Then press the
Numeric Key H as required to enter the
desired letter. This is the way you would
enter the second “O” in the word ZOOM,
and again for the letter “M.”
c. To enter a blank space, press the ›
Navigation Buttons E twice. The first
press will move the cursor to the right, and
the second press will move the cursor one
more space to the right, leaving a blank
space between the last letter and the next
one.
9. Repeat Steps 7 and 8 as needed to complete
entering the needed letters, numbers, characters and spaces.
10. When the text entry is complete, press the
Set Button F. The new name will be
entered into the remote’s memory, replacing
the default name.
11. At this point you have two options:
a. If you wish to program an additional key
within the same device, press the Set
Button F as instructed by the bottom
line of the LCD display reading ANOTHER
KEY. The remote will return to the SELECT
A KEY menu option as shown in Step 6.
Repeat the instructions in Steps 6 though
11 to rename the next key.
b. If you have no additional keys to rename,
press the ⁄ Navigation Buttons E
once so that the menu screen displays EXIT
on the bottom line of the display. Press the
Set Button F to return the remote to
normal operation.
Notes on Renaming Keys:
• Renaming a key does not change its function.
You may change the function of an individual
key by learning a new code into the remote.
See page 57 for more information.
• When a key is renamed it will only apply to the
specific device selected in Step 4. The same key
may be renamed as needed for each individual
device with which it is used.
Resetting the Remote
Depending on the way in which the remote has
been programmed, there may be a situation
where you wish to totally erase all changes that
have been made to the remote and return it to
the factory defaults. You may do that by following the steps shown below, but remember that
once the remote is reset, ALL changes that have
been made, including programming for use with
other devices, learned keys, macros, punchthrough settings and key names, will be erased
and any settings you had previously made will
have to be reentered.
To erase all settings and reset the remote to the
original factory default settings and displays, follow these steps:
1. Press and hold the Program Button for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display 2. Release the button when the red light under the Set Button
F appears.
2. The remote’s MAIN MENU message (Figure
26), will appear in the LCD display and the
Set Button F will remain illuminated in
red. Press the ⁄¤ Navigation Buttons
E until USER RESET appears on the bottom line of the LCD screen, as shown in Figure
82.
MAIN MENU
USER RESET
Figure 82
3. Press the Set Button F to reset the
remote. Note that once the Set Button is
pressed the process may not be stopped. While
the remote’s memory is being cleared a
RESETTING... message will appear in the
upper line of the remote’s LCD screen as
shown in Figure 83.
It may take a few minutes for the reset process
to take place, and the length of time will vary
depending on how much customization and
programming has taken place. Please be
patient; as long as the message appears in the
display the remote is functioning properly.
RESETTING...
Figure 83
4. When the remote has been totally reset and
returned to the factory default condition, a
REMOTE RESET COMPLETE message will
appear (Figure 84) briefly, and then the remote
will return to normal operation.
REMOTE RESET
COMPLETE
Figure 84
Backlight Options
The AVR 445’s remote has a built-in backlight
system that makes it easier to use the remote
when the room lighting is dimmed for an optimal
home theater experience. To turn the backlighting on, simply press the Light Button Q. That
button is made from a special “glow” material
that makes it easier to find in dark rooms. This
glow feature does not use any battery power, so
the glow will fade when the remote is kept in a
dark room for an extended period of time. You
may “recharge” it by placing the remote in normal room lighting for a few hours.
Once the Light Button Q is pressed, the
remote’s backlighting will remain on for approximately 7 seconds, and when you press any button on the remote while the backlighting is on,
the light will stay on for another 7 seconds.
However, the remote’s “Couch” function will
conserve battery power by turning both the backlighting and the LCD display off when any button
is pressed for more than 30 seconds.
You may also configure the remote so that the
backlighting will come on, any time a button is
pressed.
To set this option, follow these steps:
1. Press and hold the Program Button for
about 3 seconds while the message shown in
Figure 25 appears in the remote’s LCD display.
Release the button when the red light under
the Set Button F appears.
2. When the remote’s Main Menu message (Fig.
26) appears in the LCD display and the Set
Button F remains illuminated in red, press
the ⁄¤ Navigation Buttons E until
BACK LIGHT appears in the bottom line
of the LCD screen, as shown in Figure 85.
MAIN MENU
BACK LIGHT
Figure 85
PROGRAMMING THE REMOTE 59
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Programming the Remote
Programming the Remote
3. Press the Set Button F and then press
the⁄¤ Navigation Buttons E again so
that O N FULL appears in the bottom line of
the LCD display, as shown in Figure 86.
BACK LIGHT
ON FULL
Figure 86
4. Press the Set Button F one more time. The
LCD display will show the word SAVING on
the top line for about 2 seconds and then flash
SAVED four times on the bottom line to
indicate that the setting has been accepted by
the remote’s memory.
5. The remote’s backlighting will now turn on
whenever a button is pressed. To revert to the
original setting, follow the four steps shown
above, but in Step 3, select the option that has
the word NORMAL on the bottom line of the
LCD display.
Additional Notes on Configuring and
Operating the Remote:
• When the remote is being programmed, it will
automatically time-out if no button is pressed
within a thirty-second period. The message
shown in Figure 87 will appear briefly, and the
remote will then exit the feature being programmed and any data entered will be lost.
TIME OUT OR
CLR KEY PRESSED
Figure 87
• The programming or configuration process may
also be stopped at any time by pressing the
Clear Button . The message shown in
Figure 87 will appear, the data entered in the
current process will be lost and the remote will
return to normal operation. Any process that
was underway when the button will be pressed
must be re-started.
• Extensive use of the programming, learning
and configuration functions of the remote may
consume significantly more battery power than
normal remote operation. While the batteries
should last for four to six months in normal
operation, you may find that they need to be
changed sooner after the remote is programmed for the first time.
60 PROGRAMMING THE REMOTE
Downloaded from www.Manualslib.com manuals search engine
• When the batteries approach a level below
which the remote will not function, the
remote’s LCD screen will display a LOW
BATTERY warning as shown in Figure 88. We
strongly recommend replacing the batteries as
soon as this message appears to avoid the loss
of programming and configuration settings.
These settings are not lost when the batteries
are changed quickly.
AVR
LOW BATTERY
Figure 88
• The remote has a built-in backlight that may be
activated by pressing the Light Button Q.
This button is made from a special “glow”
material so that it is easier to find in dark
rooms. This glow feature does not consume any
electricity, but the glow will fade when the
remote is kept in a dark location for an
extended period of time. The “glow” feature
may be restored by placing the remote in
normal room light for a few hours.
• The remote’s backlight will remain lit for
approximately five seconds after the Light
Button Q is pressed, and it will stay lit for
another five seconds if any key is pressed while
the backlight is on. You may keep the backlight
lit by holding the Light Button, but extensive
use of the backlight will reduce battery life.
• The LCD display will remain on for ten seconds
after a key is pressed and then turn off to
conserve battery life.
• When any button is held for more than thirty
seconds the LCD will turn off and the remote
will stop transmitting the codes to conserve
battery life.
SYMPTOM
CAUSE
SOLUTION
Unit does not function when Main
Power Switch 1 is pushed
• No AC Power
• Make certain AC power cord is plugged
into a live outlet
• Check to see if outlet is switch controlled
Display lights, but no sound
or picture
• Intermittent input connections
• Make certain that all input and speaker
connections are secure
• Press Mute button K
• Turn up volume control
• Mute is on
• Volume control is down
Units turns on, but Front-Panel
Display does not light
• Display brightness is turned off
• Follow the instructions in the Display Brightness section
on page 45 so that the display is set to VFD FULL
No sound from any speaker;
light around Power switch 2 is red
• Amplifier is in protection mode
due to possible short
• Amplifier is in protection mode
due to internal problems
• Check speaker-wire connections for shorts at receiver
and speaker ends
• Contact your local Harman Kardon service depot
No sound from surround or
center speakers
• Incorrect surround mode
• Input is mono
• Select a mode other than Stereo
• There is no surround information from mono sources (except with
Theater and Hall surround modes)
• Check speaker mode configuration
• Some surround modes may not create rear-channel information
from nonencoded programs
• Incorrect configuration
• Stereo or Mono program material
Unit does not respond to
remote commands
• Weak batteries in remote
• Wrong device selected
• Remote sensor ¯ is obscured
• Change remote batteries
• Press the AVR Selector B
• Make certain front-panel sensor is visible to remote or
connect remote sensor
Intermittent buzzing in tuner
• Local interference
• Move unit or antenna away from computers, fluorescent lights,
motors or other electrical appliances
Letters flash in the Channel Indicator
Display Ú and Digital Audio stops
• Digital audio feed paused
• Resume play for DVD
• Check that Digital Signal is fed to the Digital Input selected
Processor Reset
In the rare case where the unit’s operation or the
displays seem abnormal, the cause may involve
the erratic operation of the system’s memory or
microprocessor.
To correct this problem, first unplug the unit from
the AC wall outlet and wait at least three
minutes. After the pause, reconnect the AC
power cord and check the unit’s operation. If the
system still malfunctions, a system reset may
clear the problem.
To clear the AVR’s entire system memory
including tuner presets, output level settings,
delay times and speaker configuration data, first
put the unit in Standby by pressing the System
Power Control button 2. Next, press the
Surround Mode 5 and the RDS ^ buttons
simultaneously for three seconds.
NOTE: Resetting the processor will erase any
configuration settings you have made for
speakers, output levels, surround modes, digital
input assignments as well as the tuner presets.
After a reset the unit will be returned to the
factory presets, and all settings for these items
must be reentered.
The unit will turn on automatically and display
the RESET message in the Main Information Display ˜. Note that once you have
cleared the memory in this manner, it is necessary
to re-establish all system configuration settings
and tuner presets.
If the system is still operating incorrectly, there
may have been an electronic discharge or severe
AC line interference that has corrupted the
memory or microprocessor.
If these steps do not solve the problem, consult
an authorized Harman Kardon service depot.
TROUBLESHOOTING GUIDE 61
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Troubleshooting Guide
APPENDIX
System Defaults
The two tables in this section show the factory default settings for the Video Inputs, Video Sources and Video Display Aspect Ratios. These tables give you the
complete picture on the AVR 445’s initial settings. You may then decide whether any item needs to be changed so that it is more appropriate for your specific
installation. Any of the settings shown may be changed as shown in the pages of the System Configuration section of this manual (pages 23 to 35).
Table 1: Video Input Defaults
INPUT
Video 1
Video 2
Video 3
Video 4
DVD
HDMI 1
HDMI 2
Tuner
CD
Tape
DMP/The Bridge
6/8 CH Direct
USB
AUDIO
INPUT
ANALOG
ANALOG
OPTICAL 1
ANALOG
COAX 1
OPTICAL 3
COAXIAL 3
ANALOG
ANALOG
ANALOG
ANALOG
ANALOG
---
VIDEO
INPUT
AUTO
AUTO
AUTO
AUTO
AUTO
HDMI 1
HDMI 2
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
COMPONENT
VIDEO INPUT
OFF
OFF
COMPONENT 1
COMPONENT 2
COMPONENT 3
----OFF
OFF
OFF
OFF
OFF
OFF
RECORD
OUTPUT
ANALOG
ANALOG
ANALOG
ANALOG
ANALOG
DSP DOWNMIX
DSP DOWNMIX
ANALOG
ANALOG
ANALOG
ANALOG
ANALOG
DSP DOWNMIX
System Default and Personal Settings Worksheets
The worksheets in this section show the system defaults for the global settings on your AVR 445. Once your system is configured manually, or through the
use of EzSet/EQ, where applicable, we recommend that you use the “Your System Settings” column to record your personal preferences so that they may be
restored in the event the AVR’s memory is lost due to an extended power outage, system upgrade, processor reset, or other major service to your unit.
Additional copies of this worksheet may be downloaded from the Harman Kardon web site at www.harmankardon.com
62 APPENDIX
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
APPENDIX
Worksheet B: Surround Configuration Defaults and Settings
Feature
Logic 7 Global
Default Surround
Dolby Pro Logic II Music Center Width
Dolby Pro Logic II Music Dimension
Dolby Pro Logic II Panorama
Dolby Pro Logic IIx Music Center Width
Dolby Pro Logic IIx Music Dimension
Dolby Pro Logic IIx Panorama
Night Mode
System Default
Off
Original
3
0
Off
3
0
Off
Off
Your System Settings
Worksheet C: Delay Defaults and Setting
Feature
Front Left
Center
Front Right
Surround Right
Surround Back Right
Surround Back Left
Surround Left
Subwoofers
System Default
12.0 Feet
12.0 Feet
12.0 Feet
10.0 Feet
10.0 Feet
10.0 Feet
10.0 Feet
12.0 Feet
Your System Settings
Worksheet D: System Defaults and Settings
Feature
Front L/R Speaker Size & X-Over
Center Speaker Size & X-Over
Surround L/R Speaker Size & X-Over
Surround Back Speaker Size & X-Over
LFE LP Filter
Sub Mode
Channel Adjust
Sub Size
VFD Fade Time Out
VFD Brightness
Volume Default
Volume Default Set
Semi OSD Time Out
Full OSD Time Out
DMP Auto Power
Surround Back Amps
Carrier Out
System Default
Small – 100 Hz
Small – 100 Hz
Small – 100 Hz
None
100 Hz
Sub
Global
10 in/250 mm
Off
Full
Off
-25dB
5 Sec
20 Sec
Off
Main
Zone II
Your System Settings
APPENDIX 63
Downloaded from www.Manualslib.com manuals search engine
64 APPENDIX
Downloaded from www.Manualslib.com manuals search engine
Treble
Bass
Tone In/Out
ADC Sampling
Auto Poll
Record Output
A/V Sync Delay
Video Processing
Component Video Input
Video In Port
Audio Auto Poll
Audio In Port
Surround Mode
Input Title
FEATURE
DVD
Worksheet E: Input Settings
Video 1
Video 2
Video 3
Video 4
HDMI 1
HDMI 2
CD
Tape
Tuner
The Bridge
USB
6/8 Ch Direct
APPENDIX
Audio Section
Stereo Mode
Continuous Average Power (FTC)
80 Watts per channel, 20 Hz–20 kHz,
@ < 0.07% THD, both channels driven into 8 ohms
5/7 Channel Surround Modes
Power Per Individual Channel
Front L&R channels:
65 Watts per channel,
@ < 0.07% THD, 20 Hz–20 kHz into 8 ohms
Center channel:
65 Watts, @ < 0.07% THD, 20 Hz–20 kHz into 8 ohms
Surround (L & R Side, L & R Back) channels:
65 Watts per channel,
@ < 0.07% THD, 20 Hz–20 kHz into 8 ohms
Input Sensitivity/Impedance
Linear (High Level)
200mV/47kohms
Signal-to-Noise Ratio (IHF-A)
95 dB
Surround System Adjacent Channel Separation
Analog Decoding
40 dB
(Pro Logic, etc.)
Dolby Digital (AC-3)
55 dB
DTS
55 dB
FM Tuner Section
Frequency Range
Usable Sensitivity
Signal-to-Noise Ratio
Distortion
Stereo Separation
Selectivity
Image Rejection
IF Rejection
87.5–108 MHz
IHF 1.3 µV/13.2 dBf
Mono/Stereo: 70/68 dB (DIN)
Mono/Stereo: 0.15/0.2%
40 dB @ 1 kHz
±400 kHz: 70 dB
80 dB
90 dB
AM Tuner Section
Frequency Range
Signal-to-Noise Ratio
Usable Sensitivity
Distortion
Selectivity
520–1710 kHz
45 dB
Loop: 500µV
1 kHz, 50% Mod: 0.8%
±10 kHz: 30 dB
Video Section
Video Format
Input Level/Impedance
Output Level/Impedance
Video Frequency Response
(Composite and S-Video)
Video Frequency
Response (Component)
PAL/NTSC
1Vp-p/75 ohms
1Vp-p/75 ohms
10 Hz–8 MHz (–3 dB)
10 Hz-50 MHz (–3 dB)
HDMI Version 1.1
Frequency Response
@ 1W (+0 dB, –3 dB)
10 Hz–130 kHz
High Instantaneous
Current Capability (HCC)
±40 Amps
Transient Intermodulation
Distortion (TIM)
Unmeasurable
Rise Time
16 µsec
Slew Rate
40V/µsec**
General
Power Requirement
Power Consumption
Dimensions (Max)
Width
Height
Depth
Weight
AC 220-240 V/50 Hz
120 W idle, 1180 W maximum
(7 channels driven)
440 mm
165 mm
435 mm
17.7 kg
Depth measurement includes knobs, buttons and terminal connections. Height measurement
includes feet and chassis. All features and specifications are subject to change without notice.
Harman Kardon and Power for the Digital Revolution are registered trademarks of
Harman International Industries, Incorporated.
The
are trademarks of Harman International Industries, Incorporated.
Bridge and
(Patent No. 5,386,478).
*Manufactured under license from Dolby Laboratories.
“Dolby,” “Pro Logic,” “Pro Logic II,” "Pro Logix IIx" and the Double-D symbol are trademarks of
Dolby Laboratories. Confidential Unpublished Works. ©1992–1999 Dolby Laboratories, Inc.
All rights reserved.
DTS and DTS Surround, DTS-ES and DTS Neo:6 are trademarks of Digital Theater Systems, Inc.
Logic 7 is a registered trademark of Harman International Industries, Incorporated.
A-BUS and A-BUS/READY ® Ready are registered trademarks of Leisure Tech Electronics Pty Ltd
Australia.
TiVo is a registered trademark of TiVo, Inc.
SACD is a trademark of Sony Corporation.
iPod is a registered trademark of Apple Computer, Inc.
DLP and Texas Instruments are trademarks of Texas Instruments.
HD-DVD is a trademark of the DVD Format/Logo Licensing Corporation (DVD FLLC).
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing, LLC.
Microsoft, Windows and Windows Media are registered trademarks of Microsoft Corporation in
the United States and other countries.
**Without input anti slewing and output isolation networks.
TM
TECHNICAL SPECIFICATIONS 65
Downloaded from www.Manualslib.com manuals search engine
ENGLISH
Technical Specifications
250 Crossways Park Drive, Woodbury, New York 11797
www.harmankardon.com
Harman Consumer Group, Inc.:
2, route de Tours, 72500 Château-du-Loir, France
© 2006 Harman Kardon, Incorporated
Part No.: ZKD3201HA00
Downloaded from www.Manualslib.com manuals search engine