GALILEO™ STROBE POWER SUPPLY
SNG690-P
WARNING
High Voltage! Wait 5 minutes after shutting the unit OFF before attempting service. Warranty void if seal is broken.
Included with the Power Supply:
1.
One Power Wire Harness consisting of one amp 3 pin connector with three wires: red (+), black (-) and violet.
2.
One Flash Control Wire Harness consisting of one amp 3 pin connector with three wires: yellow, green and blue.
GALILEO™
Strobe Power Supply
6 Head 90 Watt
Featuring
WARNING: High Voltage! Please wait 5 minutes after shutting this unit off before attempting service. Warranty void if seal is broken.
Output
1
Output
2
Output
3
Output
4
Output
5
Output
6
WARNING
This Power Supply is NOT waterproof.
This Strobe Power Supply must be mounted in an area protected from the weather and water.
OUTPUT SOCKETS
LIGHT HEAD CONNECTION
FUSE
POWER
INPUT SOCKET
FLASH CONTROL
INPUT SOCKET
STROBE POWER SUPPLY
SPECIFICATIONS
Voltage
Current
Power
Fuse
Number of Heads
10-30 Vdc
8.5 Amps @12.8 Vdc
90 Watts
15 Amp
6
Figure A.
INSTALLATION
1.
Install the Strobe Power Supply in a protected location using the Power Supply itself as a template. THE POWER SUPPLY
MUST BE MOUNTED TO A METAL SURFACE. Make sure all of the connectors are easily accessible. The unit is mounted using the
4 mounting holes on a 6” x 2.5” rectangle.
2.
Install the Strobe Light Heads in the preferred locations.
3.
String the 3 conductor cables between the lights and Power
Supply. Make sure the cable is secure along the chosen routing inside the vehicle to prevent it from damage by chafing or binding.
Be sure to keep the cable away from engine HOT spots.
NOTE
When routing the cable, make sure the end with the closed tip terminals (male pins) is toward the Power Supply and the end with the open tip terminals (female pins) is toward the light head.
MALE AMP CONNECTOR
(to be mated with the AMP output socket on the power supply)
Insert wires with male pins into the proper locations in the male
AMP connector:
RED WIRE - HOLE 1
BLACK WIRE - HOLE 2
WHITE WIRE - HOLE 3
FEMALE AMP
CONNECTOR
Insert wires with female pins into the proper locations in the female
AMP connector:
RED WIRE - HOLE 1
BLACK WIRE - HOLE 2
WHITE WIRE - HOLE 3
AMP WIRE HARNESS
(attached to strobe light head)
Figure B.
4.
Insert the pins on each end of the conductor cables into the amp connectors. Each end of these cables has a factory crimped pin on each of the three wires, see Figure B.
POWER WIRE HARNESS ASSEMBLY
The Power Wire Harness Assembly consists of an amp 3 pin connector with red and black wires to supply power and ground, and a violet wire to select different patterns, see Figure D.
NOTE
It is important to follow the correct color code when inserting the pins into the amp connectors.
5.
Connect the cables to the Strobe Light Heads.
6.
Plug the other end of the cable into the Light Head Output
Socket on the Strobe Power Supply, see Figure A. The location of the connector for each light head attached to the unit will be determined by the flash pattern selected, see Figure E.
7.
Plug the Flash Control Wire Harness Assembly into the Flash
Control Input Socket on the Strobe Power Supply. Connect the wires from the Flash Control Wire Harness Assembly to the switch control panel, see Flash Control Wire Harness Assembly Section.
8.
Plug the Power Wire Harness Assembly into the Power Input
Socket. Connect the Strobe Power Supply to the power source to complete the installation, see Power Wire Harness Assembly
Section.
AMP 3 PIN
CONNECTOR
HOUSING
RIDGE INDICATES
LOCATION OF HOLE #1
Figure D.
NOTE
RED WIRE - HOLE 1
BLACK WIRE - HOLE 2
VIOLET WIRE - HOLE 3
If the special flash options (Double, Quint,
WarpFlash™) are to be used, see Special Mode
Section.
FLASH CONTROL WIRE HARNESS ASSEMBLY
The Flash Control Wire Harness Assembly consists of an amp 3 pin connector with three wires: yellow, green and blue, see Figure
C. The blue wire controls the light head outlets 1-4 and the green wire controls the light head outlets 5 and 6. The yellow wire is used for pattern selection.
NOTE
If the special flash options (Double, Quint,
WarpFlash™) are to be used, see Special Mode
Section.
SIMULTANEOUS
FLASH A
1 2 3 4 5 6
CONTROL POWER
BLUE
VIOLET
SIMULTANEOUS
FLASH B
GREEN
YELLOW
BLACK (-)
RED (+)
RIDGE INDICATES
LOCATION OF HOLE #1
Figure E.
AMP 3 PIN
CONNECTOR
HOUSING
Figure C.
YELLOW WIRE - HOLE 1
GREEN WIRE - HOLE 2
BLUE WIRE - HOLE 3
The Flash Control Harness Assembly must be connected to the
Flash Control Input Socket located on the Strobe Power Supply, see Figure A. Use 18 gauge wire to extend the proper Flash
Control Harness wires to a customer supplied switching system.
The Power Wire Harness is connected to the Power Input Socket located on the Strobe Power Supply, see Figure A. If necessary, use 18 gauge wire to extend the violet wire to a customer supplied switching system, see Figure G. Connect the red wire to the positive (+) side of the battery making sure to place a customer supplied 15 amp fuse at the battery. Connect the black wire to the negative (-) side of the battery or to the vehicle chassis.
NOTE
To extend the power (+) and ground (-) wires, use the following as a guide:
1 to 10 ft. use 18 AWG Wire
10 to 20 ft. use 16 AWG Wire
20 to 30 ft. use 14 AWG Wire
30 to 50 ft. use 12 AWG Wire
SWITCH CONTROL OPTIONS
Figures F and G show some of the standard switch control options that can be easily wired to complete a Strobe Light System.
Figure F shows an ON/OFF control system that quad flashes all heads.
Figure G shows how any flash option could be installed depending on which control wire(s) are attached to the switch.
CONTROL POWER
RED (+)
DIRECT CONNECTION
OPTIONAL CONNECTION
CONTROL POWER
RED (+)
VIOLET
(remove)
15 AMP FUSE
(+)10-30 Vdc
SPST ON/OFF SWITCH
(Rear View)
15 AMP FUSE
(+)10-30 Vdc
SPST ON/OFF SWITCH
(Rear View)
Figure F.
Standard Quad Flash All Heads ON/OFF Switching
Figure G.
Special Pattern Options ON/OFF Switching
To Reduce EMI emissions, ONE end of the shield (drain wire) of the extension cable connecting the output of the power supply to the Lighthead should be connected to ground. Make sure ONLY ONE END of the shield is tied to ground. The other end needs to be taped or cut.
WARRANTY
Sirennet warranties the SNG690-P Galileo™ Strobe Power Supply for two (2) years from the date of purchase to the original purchaser against any manufactured defects or workmanship. This warranty is a 100% replacement value warranty. It applies only to units installed according to manufacturer’s installation instructions and operated within the units specifications. Warranty is void if the unit was installed incorrectly or maliciously damaged. All warranty claims must be accompanied by a dated proof of purchase.
Sirennet retains the right to be the sole mediator of what constitutes defects in performance or manufacturing.
!
W A R N IN G
P E R S O N A L IN J U R Y H A Z A R D
M ounting this devic e in a n im proper loc a tion m a y im pa ir the des ig ned s a fety c ha ra c teris tic s of the vehic le in the event of a c ollis ion.
C ons ult the vehic le m a nufa c turer before ins ta lling this or a ny other a fterm a rk et devic e to determ ine its proper m ounting loc a tion.
Fa ilure to c ons ult a nd follow the vehic le m a nufa c turer’s m ounting rec om m enda tions m a y res ult in s erious pers ona l injury or dea th.
SPECIAL MODE
To select any one of the different Flash Modes, simply connect the yellow, violet, blue and green wires to a switch in the following combinations. POWER = 10-30 Vdc and NC/GND = no connection or ground.
STEP 1
Select Pattern
STEP 2
Select Heads to Flash
VIOLET
NC/GND
NC/GND
POWER
POWER
YELLOW
NC/GND
POWER
NC/GND
POWER
PATTERN
Double Flash (235 FPM)
Quad Flash (140 FPM)
Quint Flash (140 FPM)
WarpFlash™ (700 FPM)
GREEN
NC/GND
NC/GND
POWER
POWER
BLUE
NC/GND
POWER
NC/GND
POWER
PATTERN
All Heads OFF
1 & 2 Alt. 3 & 4
5 Alt. 6
1 & 2 & 5 Alt. 3 & 4 & 6
NOTE
Applying voltage to only the violet and/or the yellow wire(s) will not turn on the Power Supply. Only the green and blue wire(s) will turn the Power Supply on.
SNG690-P 12.09
