Tri-Band 4G-C
Tri-Band 4G-C
Adjustable Gain
800 / AWS 1700 / 2100 / 1900 MHz
In-Building Wireless
Smart Technology ™
Signal Booster
Contents:
Antenna Options & Accessories . . . . . . . . . . . . . . . . . . . . 1
Quick Install Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Finding the Strongest Signal. . . . . . . . . . . . . . . . . . . . . . . 5
Outside Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . 6
Inside Antenna Installation. . . . . . . . . . . . . . . . . . . . . . . . 8
Installing a Wilson Electronics Signal Booster. . . . . . . . . 9
Powering up a Wilson Electronics Signal Booster. . . . . . . 9
Understanding the Signal Booster Lights . . . . . . . . . . . . 10
Warnings and Recommendations. . . . . . . . . . . . . . . . . . 12
Guarantee & Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Appearance of device and accessories may vary.
Note: This manual contains important safety and operating information. Please read and
follow the instructions in this manual. Failure to do so could be hazardous and result in
damage to your Signal Booster.
Installation Instructions for the Following Wilson
Electronics Signal Booster:
Tri-Band 4G-C
Adjustable Gain 800 / AWS 1700 / 2100 / 1900 MHz
In-Building Wireless Smart Technology ™ Signal Booster
Model # 272770 FCC ID: PW0272770 IC: 4726A-272770
The term “IC” before the radio certification number only signifies that Industry Canada technical
specifications were met.
How it Works
Wilson Electronics Signal Boosters are bi-directional devices that deliver service
levels consistent with what would be expected in areas of high cell network coverage.
They amplify a weak or shadowed signal in mobile, marine, machine to machine
and in-building applications. When using a Wilson Electronics Signal Booster in
conjunction with Wilson Electronics antennas, the Outside Antenna will collect the
cell tower signal and send it through the cable to the Signal Booster. The signal is
then amplified and re-transmitted through the Inside Antenna into the room. Cell
phones and cellular data cards in that area then communicate with the improved
signal. When a cell phone or cellular device transmits, the signal is received by
the Inside Antenna, amplified by the Signal Booster and transmitted back to the
cell tower through the Outside Antenna.
Inside this Package
Note: Kits may contain different accessories
AC/DC
Power Supply
5V / 4A
(859998)
Outdoor Antenna Options
1. Wide Band Directional Antenna
700-2700 MHz (304411)
2. Pole Mount Panel Antenna
700-2700 MHz (304453)
3. 2 (qty.) 20’ RG-58 coaxial cables (951104)
1
2
3
Signal Booster
Indoor Antenna Options & Accessories
A. Wide-Band Panel Antenna 700-2700 MHz
(multiple mounting options)
B. 50 Ohm Lightning Surge Protector with N-Connector (859902)
Splitter options on page 8
A
B
Appearance of device and accessories may vary.
1
To purchase, call Wilson Electronics Sales Department at: 800-204-4104
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Quick Install Overview
Refer to Installation Diagram on page 3 & 4. Contact Wilson Electronics Technical
Support Team with any questions at 866-294-1660.
1. Select a location to install the Signal Booster that is away from excessive heat,
direct sunlight, moisture and has proper ventilation. Do not place the Signal
Booster in an air-tight enclosure.
2. Select a location on the roof of the building to install the Outside Antenna. Use
a cell phone in test mode to find the strongest signal from the cell tower (refer
to pages 5 & 6). Visit www.WilsonElectronics.com to find test mode function for
your particular cell phone.
3. Run the Outside Antenna cable to the Signal Booster and attach it to the
connector labeled “Outside Antenna” on the Signal Booster. Run the Inside
Antenna cable to the Signal Booster and attach it to the connector labeled
“Inside Antenna” on the Signal Booster. For more information on running cable
(refer to page 7). Lightning Surge Protection is recommended for all in-building
installations (refer to page 7).
4. Select a location for the Inside Antenna, preferably in the center of where the
signal needs to be amplified. A minimum separation distance of 20 vertical
(within the null zone) or 50 horizontal feet is necessary for proper operation.
If the inside coverage is not sufficient you may need to increase the separation
distance even further (refer to installation diagram on pages 3 & 4).
5. Before powering up the Signal Booster, verify that both the Outside Antenna and
the Inside Antenna are connected and check that all connections are tight.
Note: Be careful when plugging the connectors in so as not to bend the center
pins on the connectors (refer to page 9).
6. The Signal Booster has been packaged with the gain control knobs adjusted to
the highest gain position. If any of the lights are not green, please refer to pages
10 & 11.
Warning: Connecting the Signal Booster directly to a cell phone with use of an adapter will damage the cell phone and/or the Signal Booster.
IMPORTANT NOTICE
• It is very important to power your Signal Booster using a
surge protected AC Power Strip with at least a 1000 Joule
rating.
• Failure to do this will void your warranty in the event of a
power surge or lightning strike.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
2
Installation Diagram
Outside
Antenna
Inside Antenna
Preferred Method: Place the Inside
Antenna in the ceiling facing down for
the best coverage.
Note: The Inside Antenna may be
mounted on the wall directly under the
Outside Antenna, in the null zone, if
20 feet of vertical separation can be
maintained.
Null Zone: The area under the
Outside Antenna, where the
Outside Antenna radiates the
least.
Note: A Lightning Surge Protector is
recommended for all building installations
(sold separately). Make sure the protector
is installed in line between the Outside
Antenna and the Signal Booster.
Inside Antenna
(Optional
second
antenna for
additional
coverage).
Power
Supply
Typical Installation
3
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Before Getting Started
This guide will help you properly install your Wilson Electronics Signal Booster. It
is important to read through all of the installation steps for your particular
application prior to installing any equipment. Read through the instructions,
visualize where all the equipment will need to be installed and do a soft
installation before mounting any equipment. Contact Wilson Electronics Technical
Support with any questions at: 866-294-1660.
Splitter (2-way, 3-way or
4-way if using multiple
Inside Antennas)
Lightning
Surge Protector
(recommended)
Inside Antenna
(Optional
third antenna
for additional
coverage)
Signal
Booster
Surge Protector
Power Strip
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
4
Reasons for Weak Cellular Signals
Anyone who uses a cell phone or cellular data card knows the frustration of not
being able to connect to or maintain a strong cellular signal. When this occurs, it is
generally due to one of two reasons:
1. Location of the Nearest Cell Tower – Cell towers are situated to provide broad
coverage; however, there are many areas in which signal strength may be
reduced by topographic features or by local government restrictions on the
height or placement of the towers themselves. Rural areas generally have
fewer cell towers than urban regions.
2. Natural and Man-Made Obstructions – Signal strength can also be negatively
affected by trees, hills, buildings, weather, and other obstructions. You may be
relatively close to a cell tower but still unable to make a call. This often occurs
in homes, offices and other buildings in which stucco, concrete or metal walls
may block the signal.
The Signal Booster works with two antennas. The Inside Antenna communicates
with your cell phone and the Outside Antenna communicates with the cell tower.
The Outside Antenna receives the cell tower signal and sends it through the cable
to the Signal Booster, where it is amplified and re-transmitted much stronger
through the Inside Antenna into the room. When the Inside Antenna picks up
a signal from your cellular device, the Signal Booster amplifies that signal and
transmits it through the cable to the Outside Antenna and back to the cell tower.
Note: The Signal Booster will only operate if there is an adequate signal to amplify.
Finding the Strongest Signal
When installing your Signal Booster’s Outside Antenna, aiming it towards the best
signal source from your service provider is important. The best way of getting the
strongest signal is to have one person on the roof to rotate the Outside Antenna,
which is connected to the Signal Booster. Turning the Outside Antenna about 45
degrees at a time, while the second person is watching the signal strength on the
phone inside the building. This allows you to read the signal strength from the cell
tower. It is preferable to have the phone in the test mode so the actual signal
strength can be read, as bars are not the most accurate.
Go to www.WilsonElectronics.com for help in finding the test mode for your
phone. Always make sure the person inside the building gives the signal time to
arrive and register on the phone (between 10-30 seconds for phone to reset to the
signal reading).
5
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Cell Signal
Cell Tower
Outside
Wide Band
Antenna
Signal Strength Graph
EXCELLENT
-50dB
-60dB
GOOD
-70dB
-80dB
POOR
-90dB
NO
SIGNAL
-100dB
-110dB
Signal readings usually appear as a negative number (for example, -86). The
closer you get to zero the stronger the signal (see graph above).
Selecting a Direction for the Outside Antenna
Select a location on the roof of the building to install the Outside Antenna. Use a
cell phone in test mode to find the strongest signal from the cell tower (see below
for more information). To get the strongest signal possible, it is very important to set
up your Outside Antenna properly. The Inside and the Outside Antenna must be
mounted in such a way that they are able to pick up the best possible cell signal on
the outside of the building and provide the best possible signal on the inside of the
building. Mount the Outside Antenna as high as possible facing the cell tower in an
area with the best possible signal coverage.
Note: Never point the front of a Directional Antenna toward the Inside Antenna.
Refer to Figures 1 & 2 on page 10.
Outside Antenna Installation (#304411 shown)
Antenna
Drip hole on bottom
Cell Tower
The antenna should be mounted as shown in the illustration above.The mounting
bracket, included with antenna, is adjustable and will accommodate pipe
diameters from 1.25 inches to 2 inches (pipe sold separately #901117). Mount
the antenna so that there is at least 3 feet of clearance in all directions around it.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
6
the phone in the test mode so the actual signal strength can be read, as bars
are not the most accurate. Go to www.WilsonElectronics.com for help in finding
the test mode for your phone. Always make sure the person inside the building
gives the signal time to arrive and register on the phone (between 10-30
seconds for phone to reset to the signal reading).
Warning: The outside fixed antenna must be connected with a minimum
of 26 feet of RG58 coax cable.
Warning: Lightning protection is recommended for all installations (sold
separately #859902). Take extreme care to ensure that neither
you nor the antenna comes near any electric power lines.
Lightning Protection Installation
(sold separately)
Install the Lightning Surge Protector
(LSP) close to the Signal Booster. Attach
the cable from the Outside Antenna to the
surge protector, using a short length of low
loss cable; attach one end to the LSP and
the other to the Outside Antenna connector
on the Signal Booster. Ensure the LSP
is properly grounded (ground wire not
included). Visit www.WilsonElectronics.com
or contact Wilson Electronics Sales Team at
800-204-4104.
To Outside
Antenna
Lightning
Surge Protector
(sold separately)
Ground Wire
(not included)
To Signal Booster
To Inside
Antenna
Signal Booster
Surge Protector Power Strip
Mounting Tips for Running Outside Antenna Cable
If you are mounting the Outside Antenna on the roof of your building, we have
found that it is easiest to run your cable underneath the down side of your roof’s
flashing. If you have satellite TV service installed you may be able to follow the
same route as the satellite TV cables that are already running from outside of your
building to the inside.
After routing the cable, we recommend sealing any areas where the cable passes
into the building with cable bushings, silicone or other waterproof sealant to keep
your installation from leaking. If you are mounting the Outside Antenna to the
outside wall of your home or building, the simplest way is to run the cable on the
outside of the wall and attach it to the exterior of your home or office. Then drill
a hole through the wall where you want the cable to appear on the inside of the
7
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
building. Before drilling, make sure that there are no electrical outlets, sewer or
water pipes, or electrical wiring in the wall that you are about to drill through as this
could potentially harm you or damage the building.
After drilling the required hole, run the cable through and seal it with cable
bushings, silicone or other waterproof sealant to enclose the hole that you have
created. In some instances, it may be possible to run the cable up into the fascia of
the attic overhang. In this circumstance, the cable will be accessible in the attic for
further routing.
Inside Antenna Installation
(Instructions are for optional Panel Antenna)
Select a location for the Inside Antenna, preferably in the center of where the
signal needs to be amplified. A minimum separation distance of 20 vertical feet
(within the null zone) or 50 horizontal feet is necessary for proper operation.
If the inside coverage is not sufficient you may need as much as 75 feet of
horizontal separation. Refer to installation diagram on pages 3 & 4.
Inside
Antenna
Ceiling
Drywall
Ceiling
Rafters
In some cases, multiple Inside Antennas may be required, for instance if you
have multiple rooms with poor signal. A signal may be split by using a splitter
(sold separately). Refer to installation diagram on pages 3 & 4.
Warning: An Inside Antenna must have a separation distance from all persons
that is at least 15 inches for the Panel Antenna.
Optional Wide Band
Inside Antenna
(sold separately–
multiple mounting
options)
Splitter Options: (sold separately)
2-way
(859957)
3-way
(859980)
4-way
(859981)
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
8
Wilson Electronics Signal Booster Installation
Select a location to install the Signal Booster that is away from excessive heat,
direct sunlight, moisture and that has proper ventilation. Do not place the Signal
Booster in an air-tight enclosure. Recommended installation locations for inbuilding Signal Boosters are near a power outlet and in a closet or on a shelf.
Note: It is important to have adequate air ventilation. Maintain at least 6 inches
of clearance from surrounding objects. Be careful when plugging the
connector in so as not to damage the center pins on the connectors.
Run the Outside Antenna cable to the Signal Booster and attach it to the
connector labeled “Outside Antenna” on the Signal Booster. Run the Inside
Antenna cable to the Signal Booster and attach it to the connector labeled “Inside
Antenna” on the Signal Booster.
Note: For distances of 20 feet or more, use Wilson low loss cable.
Powering up a Wilson Electronics Signal Booster
1. Never point the front of a Directional Outside Antenna toward the Inside Antenna.
Refer to Figures 1 & 2 on page 10.
2. Ensure that both the Outside Antenna cable and the Inside Antenna cable are
connected to the Signal Booster and the connections are tight before powering
up the Signal Booster.
3. Plug the power supply into the Signal Booster input marked “POWER” (carefully,
to avoid damaging the center pin) and then into a Surge Protector Power Strip.
4. If the Signal Booster does not have a green light(s), refer to pages 10 & 11.
5. Using multiple Signal Boosters in one installation could cause interference to the
cell tower (except for the In-Line Signal Booster 806215).
6. Contact Wilson Electronics Technical Support Team with any questions at
866-294-1660 or email [email protected] Technical Support hours are
Mon.- Fri. 7 am to 6 pm MST.
9
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
CORRECT INSTALLATION
Point antennas away from each other
Inside Panel
Antenna
Signal Booster
Figure 1
Outdoor
Antenna
INCORRECT INSTALLATION
Never point antennas toward each other
Inside Panel
Antenna
Signal Booster
Figure 2
Understanding the Signal Booster Lights and
Troubleshooting
Note: Reset the Signal Booster by disconnecting and reconnecting the power
supply from the Signal Booster.
Note: All red lights must be resolved before orange lights.
1. Green
The indicator lights on the Signal Booster will be a green if the unit is powered
up and working properly.
2. Orange
The Signal Booster is experiencing receiver overload. The Signal Booster has
protection circuits to prevent the disruption of cell towers. If one or more of the
lights are orange, this indicates that the Signal Booster has automatically
reduced the gain due to close proximity to a cell tower. To view how much the
gain has been reduced, turn the knob down until the light turns green. This
is the Actual Gain that the Signal Booster is operating on. Since the Signal
Booster adjusts gain automatically, there is no need to turn the gain down. If the
gain is not adequate for good coverage, you will need to turn the gain to
maximum and then turn the Outside Antenna away from the cell tower until the
lights turn to green. If the Signal Booster will not respond, turn the gain down
5 dB and then turn the Outside Antenna away from the cell tower. Continue
to adjust the gain and the antenna position until the light turns green. Contact
Wilson Electronics Technical Support Team for assistance.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
10
3. Red
If any of the lights on the Signal Booster are red, it is indicating the Signal
Booster has shut down to prevent an oscillation, most likely caused by
the Inside and Outside Antennas being physically too close to each other.
Without this patented protection, oscillations could be transmitted to the cell
tower, blocking calls to and from the cell tower. Oscillation occurs just like
in an audio system when you put a microphone next to a speaker and get
a big squeal. When the Inside Antenna is too close to the Outside Antenna,
the same type of oscillation occurs. If the Signal Booster has a red light, the
following steps need to be done for each affected band.
First, check the Signal Booster by unplugging the power supply and
removing the coax cables from the Signal Booster. Adjust the gain to
minimum and plug the Signal Booster back in. You should now have a green
light. If not, contact Wilson Electronics Technical Support Team.
If your lights are green then unplug the Signal Booster, reconnect the coax
cables and ensure all connections are tight. Plug the Signal Booster back in.
Increase the gain until you get a red light (for example, it may be at 50 dB
for the red light) then decrease the gain until you get a green light. If your
coverage is sufficient then you are done. If not, you will need to separate
the Inside and Outside antennas further apart. Separating the antennas is
very important to get the necessary gain for the system to provide maximum
coverage and a green light.
The Outside Antenna needs to be pointed at the cell tower with its back
facing towards the Inside Antenna (refer to Figures 1 & 2 on page 10).
Without proper orientation of the antennas, you will not be able to get the
maximum gain from the Signal Booster.
Note: If the antennas cannot be sufficiently separated, the Signal Booster will
have to operate with reduced performance by decreasing the Gain until
a green light is obtained.
11
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Warnings and Recommendations
Warning: The Directional Antenna must always be located so the back or
side points to the Inside Antenna. Never point the front of the
Outside Antenna toward the Inside Antenna – this is to prevent
oscillation.
Warning: Connecting the Signal Booster directly to the cell phone with use of
an adapter will damage the cell phone.
Warning: Use only the power supply provided. Use of a non-Wilson
Electronics product may damage your equipment.
Warning: RF Safety: All Inside Antennas used with this Signal Booster
may not have gain (less cable loss) that exceeds 10.1 dBi and
must be located at least 8 inches from all people. Outside fixed
antennas may not have gain that exceeds -0.46 dBi (less cable
loss) and must be located least 41 inches from all people. The
Outside Antenna must be connected with a minimum of 40 feet
of RG58 coax cable. All antennas shown on page 1 meet these
requirements.
Warning: Verify that both the Outside Antenna and the Inside Antenna are
connected to the Signal Booster before powering up the Signal
Booster.
Recommendation: Lightning Surge Protection is recommended for all in-building
installations.
This device complies with Part 15 of FCC rules. Operation is subject to two
conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation. Changes or modifications not expressly approved by Wilson
Electronics could void the authority to operate this equipment.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
12
About Wilson Electronics
Wilson Electronics, LLC has been a leader in the wireless communications industry
for over 40 years. The company designs and manufactures Signal Boosters,
Antennas and related components that significantly improve cellular phone signal
reception and transmission in a wide variety of applications, mobile (marine, RV,
vehicles) and in-building (home, office, machine to machine).
With extensive experience in antenna and Signal Booster research and design, the
company’s engineering team uses a state-of-the-art testing laboratory, including
an anechoic chamber and network analyzers, to fine-tune antenna designs and
performance. For its Signal Boosters, Wilson Electronics uses a double electrically
insulated RF enclosure and cell tower simulators for compliance testing.
Wilson Electronics Signal Boosters feature patented Smart Technology ™ that
enables them to automatically adjust their power based on cell tower requirements.
By detecting and preventing oscillation (feedback), signal overload and interference
with other users, these Smart Technology ™ Signal Boosters improve network cell
phone areas without compromising carrier systems.
All products are engineered and assembled in the company’s 100,000 square-foot
headquarters in St. George, Utah. Wilson Electronics has product dealers in all 50
states as well as in countries around the world.
13
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics 30-day money-back
guarantee. If for any reason the performance of any product is not acceptable, simply
return the product directly to the reseller with a dated proof of purchase.
2-Year Warranty
Wilson Electronics Signal Boosters are warranted for two (2) years against defects in
workmanship and/or materials. Warranty cases may be resolved by returning the product
directly to the reseller with a dated proof of purchase.
Signal Boosters may also be returned directly to the manufacturer at the consumer’s
expense, with a dated proof of purchase and a Returned Material Authorization (RMA)
number supplied by Wilson Electronics. Wilson Electronics shall, at its option, either repair
or replace the product. Wilson Electronics will pay for delivery of the repaired or replaced
product back to the original consumer if located within the continental U.S.
This warranty does not apply to any Signal Booster determined by Wilson Electronics to
have been subjected to misuse, abuse, neglect, or mishandling that alters or damages
physical or electronic properties.
Failure to use a surge protected AC Power Strip with at least a 1000 Joule rating will void
your warranty.
RMA numbers may be obtained by contacting Technical Support at 866-294-1660.
Disclaimer : The information provided by Wilson Electronics, LLC is believed to be
complete and accurate. However, no responsibility is assumed by Wilson Electronics,
LLC for any business or personal losses arising from its use, or for any infringements of
patents or other rights of third parties that may result from its use.
Copyright © 2013 Wilson Electronics, LLC. All rights reserved.
U.S. Patent Nos. – 7,221,967; 7,729,669; 7,486,929; 7,409,186; 7,783,318
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
14
Signal Booster Specifications
Tri-Band 4G-C
Model Number
272770
Antenna connectors
N-Female
Antenna impedance
50 Ohms
Dimensions
8.875 x 6.0 x 1.5 inch (22.5 x 15.2 x 3.8 cm)
Weight
2.8 lbs (1.270 kg)
Frequency
1
1710-2155 MHz / 824-894 MHz / 1850-1990 MHz
Passband Gain (nominal)
Uplink
Downlink
2
20 dB Bandwidth (nominal)
Uplink
Downlink
3
3
Power output for single cell phone (uplink) dBm
Power output for single cell phone (downlink) dBm
1700 / 2100 MHz
(Typical / Maximum)
800 MHz
(Typical / Maximum)
1900 MHz
(Typical / Maximum)
70 dB / 77 dB
65 dB / 72 dB
69 dB / 77 dB
69 dB / 76 dB
70 dB / 77 dB
71 dB / 78 dB
1700-2100 MHz
(Typical / Maximum)
800 MHz
(Typical / Maximum)
1900 MHz
(Typical / Maximum)
78 MHz / 87 MHz
85 MHz / 94 MHz
40 MHz / 45 MHz
38 MHz / 42 MHz
71 MHz / 79 MHz
77 MHz / 85 MHz
1700 MHz
800 MHz
1900 MHz
30.45
33.65
30.54
2100 MHz
800 MHz
1900 MHz
23.76
20.67
21.26
Power output for multiple received signals
(uplink) dBm
4
The maximum power is reduced
by the number of signals:
Maximum Power
Number of signals
1700 MHz
800 MHz
1900 MHz
2
20.8
24.5
22.7
3
17.3
20.9
19.2
4
14.8
18.4
16.7
5
12.8
16.5
14.8
6
11.2
14.9
13.2
Power output for multiple received signals
(downlink) dBm
4
The maximum power is reduced
by the number of signals:
Maximum Power
Number of signals
2100 MHz
800 MHz
1900 MHz
2
20.1
24.6
22.3
3
16.5
21.1
18.8
4
14.0
18.6
16.3
5
12.1
16.7
14.3
6
10.5
15.1
12.7
Facteur de bruit (liaison descendante/montante typique)
Isolation
Exigences d’alimentation
4 dB nominal
> 90 dB
110-240V AC, 50-60 Hz, 20W
Notes:
1. Nominal gain is the maximum gain at any frequency in the passband.
2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB lower than the passband
amplification. One of the frequencies is lower than the passband and the other is higher.
3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating
would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power
reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device.
4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: [email protected]
Phone: 866-294-1660 Local: 435-673-5021 Fax: 435-656-2432
www.twitter.com/WilsonCellular
www.facebook.com/WilsonCellular
111170_Rev06_06.19.13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement