Smart Temperature Transmitters STT 3000 Series Page 01

Smart Temperature Transmitters STT 3000 Series Page 01
Page 01
Smart Temperature Transmitters
STT 3000 Series
Precision devices, proven in the field
STT170
Smart Temperature
Transmitters
 Cost-effective, low-tier
solution with 4-20 mA
communications
 Universally PC
programmable for both
RTDs and thermocouples
 PC configuration
 Ultra compact size fits into
the smallest DIN B head
mount housing
 Sensor library with over a
dozen of the most-used
temperature sensor curves
 HART/4-20 mA output
 FOUNDATION™ fieldbus
protocol
 FISCO Certified
 FF DTM Support
STT250
Smart Temperature
Transmitters
 Universal sensor inputs
 Compact size allows direct
head mounting
 Broad selection of housings
and materials
 Remote communications
 Available with integral
engineering units meter
 Dual input model with
advanced diagnostics and
redundant sensor for critical
applications
 Supports 4-20ma/HART
Version 5 and 6/DE Output
 Sensor Matching function
 Supports EDDL and DTM
 TÜV SIL2 Certification for
safety applications
STT350
Smart Temperature
Transmitters
 For applications requiring
the ultimate in performance
and advanced solutions
 One model for most
thermocouples or RTDs (2-,
3-, or 4- wire)
 No board change,
potentiometer adjustment,
or calibration required
 Remote configurability and
rangeability
 Explosion-proof housing on
DIN rail mounting
 Remote communications for
configuration or diagnostics,
Delta T, and redundant
sensor capabilities are
standard
STT800
Temperature Measurement
Assembly
The STT800 is an installationready temperature
measurement assembly for
any of the STT 3000
transmitters, sensor heads,
sensors, thermo wells and
process connections. It is
available in short delivery
cycles and comes with custom
calibration and agency
approvals. These are high
quality probes with an
exceptional level of support
that provide ease of
engineering, procurement and
installation.
The STT800 is offered in
three models:
 STT820 – Rigid probe
assembly
 STT830 – Threaded and
socket weld thermo well
assembly
 STT840 – Drilled and
flanged thermo well
assembly
 ATEX, CSA, FM Approvals
available on all the STT800
Assemblies
PT CONTROMATIC PRIMA MANDIRI
Page 02
Software Tools
Configuration and Management Tools
Trouble-free and reliable device management
SCT 3000 Smartline
Configuration Toolkit
Smartline Configuration Toolkit
is a PC-based engineering and
maintenance tool designed
specifically for use with
Honeywell’s family of smart
field devices based on the DE
protocol.
 Access to configuration
database parameters
 Verifies all parameters are
correct
 Enables “Management of
Change”
 Microsoft Windows 95b, 98,
NT (4.0), 2000 and XP
MCT202
Honeywell MC Toolkit
The MC Toolkit handles
multiple communication
protocols, letting you configure,
monitor, diagnose, and
manage smart devices from
Honeywell and other suppliers.
This handheld configurator is
available in intrinsic as well as
non intrinsic safe versions
suitable for usage in safe as
well as hazardous areas.
 Configures both DE and
HART protocols
 Automatically verifies device
identification and database
configuration
 Provides full self-diagnostic
and device diagnostic
support
 Configures any HART
device with a published
HART Device Descriptions
(DD), regardless of device
manufacturer.
Field Device Manager
Express
Field Device Manager Express
software is versatile and
flexible, enabling process plant
engineers and operators to
perform on-thego smart device
maintenance anywhere in the
plant. It operates with Windows
7 laptop or desktop operating
systems and is used for
managing and configuring
smart HART and Profibus field
instruments.
 Provides full access to
device parameters,
configuration wizards,
diagnosis procedures
 On-line and off-line device
configuration and
maintenance information
support using both EDDL
and DTM technologies
 Simplifies commissioning
and maintenance with an
easy-to-use interface for
common tasks
 Automatic device discovery
 Provides device history as a
way to easily compare
today’s configuration with
last week’s or last month’s
Honeywell’s software tools help users configure, install, manage and maintain
smart field devices efficiently. All products are intuitive and feature rich and
easy-to-use interfaces for plant maintenance engineers, managers and
instrument technicians to manage field devices
PT CONTROMATIC PRIMA MANDIRI
Page 03
Analytical Instruments
Smart Sensors
Unique measurement technology
Unique Innovations
Honeywell is an industry proven
leader or analytical products and
solutions with unique technologies.
Innovations in analytical
measurements lead to more
reliable systems, lower total cost
solutions and safer environments.
This results in process control that
maximizes up-time and minimizes
cost to add to your bottom line.
Hydrogen Purity Concentration
The principles of thermal
conductivity are used to determine
the concentration of a specific gas
in a binary gas mixture. This
measurement is used to determine
the concentration of the coolant
and purge gases (H2 and CO2)
used on start-up and operating
cycles on hydrogen cooled turbine
generators.
 Low Drift Reduces Need for
Frequent Calibrations
 Rapid Response Provides
Immediate Indication of Process
Changes
 Time Proven, Reliable
Measurement Ensures Safe
Start-up and Operation
 On-line Measurement Helps
Increase Efficiency and Save
Operating Costs
Meredian® Glass pH Electrodes
Honeywell’s traditional glass
sensor electrodes offer time proven
reliable pH measurement for
selected applications. Designs
include combination electrodes, as
well as separate measuring and
reference electrodes.
 High Purity Water Assembly for
Accurate pH Measurement in
Low Conductivity Sample
 Separate Measuring and
Reference Electrodes Lowers
Replacement Costs
 Platinum and Gold Electrodes
for Accurate Measurement of
ORP
High Performance HB Series
Unique, rugged reference
technology extends the lifetime in
harsh process applications. This
saves on maintenance and
replacement costs
 Prevents Sensor Poisoning
 Prevent Internal Leaks and
Plugging
 Allows Extreme Temperature
and Pressure Tolerance
 Allows for Long Life in Low and
High pH Applications
DL5000 Dissolved Oxygen
Accurate and stable dissolved
oxygen measurements can be
made using Honeywell’s unique
equilibrium probe technology. This
unique technology provides
excellent performance in low parts
per billion (ppb) as well as parts
per million (ppm) applications.
 Unique Equilibrium Probe
Technology
 No Replacement of Membrane,
Electrolyte or Electrode
 Unaffected by Fouling
 Not Flow Sensitive
Durafet® pH Electrodes
Honeywell pioneered innovative pH
measurement with the first
industrial, non-glass, ISFET (Ion
Sensitive Field Effect Transistor)
based pH sensor–the Durafet pH
electrode.
 Waterproof Vario Pin Connector
Options
 Rugged Non-glass Design
Lowers Replacement Costs
 Long Term Stability Reduces
Calibration Frequency
 3-A Sanitary Design for On-line
pH Measurement in Food &
Dairy
PT CONTROMATIC PRIMA MANDIRI
Page 04
Analytical Instruments
Multiple Input Analyzer
Greater value and enhanced performance
UDA2182 Series Analyzers
The UDA2182 Series is a versatile, dual or single input
analyzer that measures pH, ORP, contacting
conductivity and dissolved oxygen. The “mix-andmatch” input design offers the user flexibility for a wide
range of applications. Its common form, fit and
function to older Honeywell analyzers make it a quick
and easy retrofit into existing panels and installations.
 Versatile Multiple Input Analyzer
 Mix and Match Process Measurements
 Entire Status at a Glance–Graphic LED Display
 Fast and Easy Commissioning–Even Wireless
Configuration
 Remote Monitoring Using Web Pages
 Single or Dual Input for pH, ORP, Contacting
Conductivity or Dissolved Oxygen
 Dual Input in any Measurement Combination
 PID Control Option
 Up to 3 Analog Outputs
 Up to 4 Alarm Relays
 Backlit Graphical LED Display
 Type 4 Case
 Infrared PC and Pocket PC Configuration
 FM/CSA Class 1, Div 2 Approval
 Event History Log
 Real Time Clock
 Auto Clean/Auto Calibration Functions
 Ethernet/Modbus Communications
 Eastern European Languages
pH Input
The pH input will accept a wide variety of
sensors–non-glass Durafet®, HB high performance pH
series and traditional glass Meredian® electrodes,
ORP combination electrodes and the HPW700 high
purity system. In addition to the basic unit the pH input
has:
 Auto Buffer Calibration
 High Purity Water Solution Compensation
 0.2 sec Update Rate for Fast Responding Durafet
pH Electrodes
Conductivity Input
The conductivity input will accept signals
from Honeywell’s standard selection of
contacting conductivity cells. The
conductivity unit also has:
 Temperature Compensation Curves
 Calculation of % Rejection/Passage and
Difference of Two Cells
 Conversions to ppm, ppb or ppt Total
Dissolved Solids (TDS)
 CO2 Concentration Algorithm
 pH from Differential Conductivity
Dissolved Oxygen Input
The dissolved oxygen input is from
Honeywell’s unique equilibrium probe. It has
these additional features:
 ppm or ppb Measurement
 Automatic or Manual Calibration
 Ambient Temperature and Atmospheric
Pressure Compensation
PT CONTROMATIC PRIMA MANDIRI
Page 05
Analytical Instruments
pH/ORP
Improved accuracy to optimize your process
A range of analyzers and transmitters for use with
Honeywell glass and non-glass sensors and mountings to
measure pH and ORP. Included in this offering is the
Durafet pH electrode, the only industrial, solid state pH
electrode on the market. For sanitary applications in the
food and dairy industries, the Sanitary Durafet is authorized
to use the 3A symbol.
For pure water applications, the HPW7000 Hi-pHurity pH
measurement system guarantees a 0.1 pH accuracy in
water samples with conductivity less than 10 uS. All the
above mentioned measurements can be used in process,
wastewater and pure water applications.
Instruments
UDA2182 Universal Dual Analyzer
DirectLine® Model DL421/422
APT 2000/4000pH Transmitter/Analyzer
Measurement
pH/ORP
pH/ORP
pH/ORP
Plastic Polysulfone Enclosure, NEMA4X,
123 x 48 x 46 mm
(4.84 x 1.89 x 1.81 In)
Plastic Enclosure Made of PBT NEMA4X,
IP65 rating
Case (HxWxD)
Display
LCD Dot Matrix, 128 x 64 dpi
LCD 4-digit, & 7-segment
7-segment LCD Display
Display Accuracy
Display Accuracy
pH : ± 0.02, Temp : ± 1.0 (C or F)
pH : ± 0.02, Temp : ± 1.0° (± 0.1° F)
Control Capability /
Advanced features
PID Control, Ethernet/Modbus
Communications, Pocket PC and infrared
configuration, Auto-buffer Calibration, High
Purity Water Solution compensation, 0.2
sec Update Rate, E European Languages
Integral Electronics / Sensor Design,
One or Two Point Calibration,
Auto Buffer Recognition
Electronic and Sensor Diagnostics, Auto Buffer
Recognition, Hart communication for transmitter
Operating Condition 0° to 60°C (32° to 140°F)
-20° to 85°C (-4° to 185°F)
-20° to 55°C (-4° to 131°F)
Operating Voltage
90-264 Vac
17-63 Hz
16-42 Vdc
2000 : 14-40 Vdc
4000 : 20-253 Vdc
Analog Outputs
Up to Three 4 to 20mA
One 4 to 20mA
2000 : One 4 to 20mA
4000 : Two 4 to 20mA
(One Dedicated to Temp)
Relays
Up to 4 Relays
N/A
2000 : N/A
4000 : Hi/Lo Alarm Relays
Mountings
Pipe, Wall, or Panel
Integral : No Electronics Mounting
Needed.
Remote : Pipe, Wall or DIN Rail
Pipe, Wall, or Panel
Approvals
CE; FM Class 1, Div. 2;
UL/CSA General Purpose
CE for Industrial Applications, ULGeneral Purpose; CSA General Purpose
FM Class I, Div 1, Groups A-D (IS); FM
Class I, Div 2, Groups A-D (N.I Field
Wiring)
CE : FM Class 1, Div. 2 (APT4000);
FM Class I, Div. 1 IS (APT2000) and Cenelec
PT CONTROMATIC PRIMA MANDIRI
Page 06
Analytical Instruments
pH/ORP
Improved accuracy to optimize your process
Sensors
Durafet® Solid State
pH Electrode
Meredian II Glass
pH Electrode
Oxidation Reduction
Potential (ORP) Electrode
HPW7000 Hi-pHurity pH
Measurement System
Measurement Range
0-14 pH
0-14 pH
1999 to 1999 mV
4-10 pH
Temperature Range
-10° to 130°C (14° to 266°F)
0° to 110°C (32° to 230°F)
-5° to 110°C (23° to 230°F)
10° to 80°C (40° to 176°F)
Pressure & Temp
Rating
Depend on Sensor
Depend on Sensor
Depend on Sensor
1 to - 10 in. WC (0.249 to - 2.49
kPa)
10° to 80°C (40° to 176°F)
Material of
Construction
Ryton body, solid state
electrode, viton and EPDM
seals
Ryton body, glass electrode,
EPDM seals
Ryton body, gold or platinum
electrode,EPDM seals
316L SS flow chamber, glass
electodes, 316 SS temp sensor
Mounting
See mounting type
See mounting type
See mounting type
Panel mounting option
Mounting
7773 Mounting
7774 mounting
7777 mounting
7794 mounting
HB Series
Measurement Range
0-14 pH
± 1600 mV ORP
0-14 pH
± 1600 mV ORP
0-14 pH
± 1600 mV ORP
0-14 pH
0-14 pH
± 1600 mV ORP
Depend on Sensor
Depend on Sensor
Depend on Sensor
-10° to 110°C
(14° to 230°F)
Depend on Sensor
Immersion/Polypropylene
: 689 kPa @ 60°C
(100 psig @ 140°F)
316 SS :
Determined by electrode
Up to
689 kPa @ 50°C
(100 psig @ 122°F)
Up to
689 kPa @ 100°C
(100 psig @ 212°F)
CPVC and Polypropylene
Pressure and
Temperature Rating
316 SS :
689 kPa @ 80°C
(100 psig @ 176°F)
CPVC :
689 kPa @ 50°C
(100 psig @ 122°F)
689 kPa @ 100°C
(100 psig @ 212°F)
Kynar :
1034 kPa @ 140°C
(150 psig @ 284°F)
Flow - throught/
Polypropylene :
689 kPa @ 60°C
(100 psig @ 140°F)
316SS:
515 kPa @ 80°C
(150 psig @ 176°F)
Material of
Construction
Polypropylene, Ryton,
or 316 SS
Ball valve, mounting
Durapet & glass
nipple & extension tube, electrode
316 SS or CPVC o-rings: bodies: Ryton
EPDM & Viton
Body: Polysulfone
Body: CPVC,
Polypropylene, kynar
Special Features
Allows separate
meassuring and
reference electrodes in
one mounting
Insertion/removal under
pressure without
interrupting process
Sanitary 3-A approval for
food and dairy
applications
Rugged reference
design minimizes fouling
a poisoning in harsh
environments
Mountings
Immersion or
flow-through
1 1/4 in. NIPT (316 SS)or Immersions or in-line tee
1 1/2 in. NIPT (CPVC)
(3/4 in. NPT fitting)
pipe nipple through ball
valve
1 1/2,2 or 3 inch
tri- clamp flange
mounting
Model 546: in-line or
submersion
Model 547: Ball valve
Model 551: Nut-loc
PT CONTROMATIC PRIMA MANDIRI
Page 07
Analytical Instruments
Conductivity
proven technology for reliable measurements
A range of analyzers and transmitters for use with
Honeywell contacting and toroidal Conductivity cells and
Mountings to measure conductivity, resistivity, salinity and
These measurements can be made in many idustrial
process and pure water applications.
Instruments
UDA2182
Universal Dual Analyzer
DirectLine
Model DL423
APT 2000/4000CC
Contacting Conductivity
APT 2000/4000TC
Toroidal Conductivity
Case (HxWxD
Plastic enclosure made of
GE Valox® 357 CSA Type 4X
(NEMA 4X)
Plastic polysulfone enclosure,
IP66, 123 x 48 x 46 mm
(4.84 x 1.89 x 1.81 in)
Plastic enclosure made of PBT
NEMA4X, IP65 rating
Plastic enclosure made of PBT
NEMA4X, IP65 rating
Display
LCD dot matrix, 128 x 64 dpi
LCD 4-digit, 7-segment
7-segment LCD display
7-segment LCD display
Display Accuracy
0.05% of reading Temperature:
0.1% from -10° to 100°C ±1.0°C
from 101° to 140°C
Conductivity/resistivity: greater
of ±2 counts or ±0.5% of reading.
Concentration: ±0.5% of reading.
Temperature: ±0.1°C from -10° to
Conductivity:
1% of measured value or ±(0.4
microS/cm* cell constant)
Conductivity:
1% of measured value
±(0.2 microS/cm
±1 Significant digit)
Control Capabilities
/Advanced Features
PID control; Pocket PC and infrared
configuration, temp. compensation
curves; CO2 concentration; ppm, ppb or
TDS conversions, Ethernet/Modbus
communications,
E. European languages
Integral electronics/sensor design;
trim value or 1 point solution
calibration
Measures conductivity,
resistivity, or salinity; electronics
and sensor diagnostics, Hart
communication for transmitter
Measures conductivity, or
chemical concentration;
electronics and sensor diagnostics,
Hart communication option
Operating Conditions
0° to 60°C (32° to 140°F)
-20° to 85°C (-4° to 185°F)
-20° to 55°C (-4° to 131°F)
-20° to 55°C (-4° to 13°F)
Operating Voltage
90-264 Vac
47-63 Hz
16-42 Vdc
2000: 14-42 Vdc
4000: 20-253 V,
AC or DC
2000: 14-42 Vdc
4000: 20-253 V, AC or DC
Analog Outputs
Up to three 4 to 20mA
One 4 to 20 mA
2000: One 4 to 20 mA; 4000:
Two 4 to 20 mA (one dedicated
to temp)
One 4 to 20 mA
Relays
Up to 4 relays
N/A
2000: N/A; 4000: Hi/Lo alarm
relays
2000: N/A; 4000: Hi/Lo alarm relays
Mountings
Pipe, wall, or panel
Remote: pipe, wall or DIN rail
Pipe, wall or panel
Pipe, wall or panel
Approvals
CE; FM Class 1, Div. 2;
UL/CSA general purpose
CE for industrial applications;
UL/CSA general purpose FM
CE; FM Class 1, Div. 2
(APT4000);
CE; FM Class 1, Div. 2 (APT4000)
Sensors
4973 Contacting
Conductivity Cells
4905 Contacting
Conductivity Cells
4909 Contacting
Conductivity Cells
5000TC Toroidal
Conductivity Cells
Measurement
Range
0.01, 0.1, 1.0, 10.0 cell constants,
0.055μS/cm to 250 mS/cm
0.01, 0.1, 10.0, 50 cell constants,
0.055μS/cm to 1S/cm
0.01, 0.1, 10.0, 50 cell
constants,
0.2 to 200 milliSiemens/cm
Pressure and
Temperature
1724 kPa @ 140°C
(250 psig @ 284°F)
1034 kPa @ 130°C
(150 psig @ 266°F)
SS: 3.45 bar @ 140°C (50psi
@ 284°F); CPVC: 2.07 bar @
140°C (30psi @ 284°F)
0.055μS/cm to 1S/cm
FM Class 1, Div. 1 IS
(APT2000); CENELEC
Polypropylene: 6.9 bar @ 100°C (100psi
@ 212°F); PVDF: 6.9 bar @ 120°C
(100psi @ 248°F); PEEK: 13.8 bar @
150°C (200psi @ 302°F); PFA Teflon:
13.8 bar @ 150°C (200psi @ 302°F)
Material of
Constructions
Titanium or graphite
Nickel or platinum
Nickel or platinum
Polypropylene, PVDF, PEEK, PFA
Teflon
Mountings
3/4 inch NPT threaded fitting
1 inch NPT threaded fitting
Insertion/Removal ball valve
Immersion, union adapter, sanitary
assembly in CPVC or SS allows 2 inch flange or insertion/removal
insertion/removal of cell without
stopping process
PT CONTROMATIC PRIMA MANDIRI
Page 08
Analytical Instruments
DISSOLVED OXYGEN
patented techniques for DO monitoring
Instruments
UDA2182
Universal Dual Analyzer
DL424 ppm
DLO425 ppb
Case (HxWxD
Plastic enclosure made of GE Valox®
357 CSA Type 4X (NEMA 4X)
Plastic polysulfone enclosure, IP66,
123 x 48 x 46 mm (4.84 x 1.89 x 1.81 in)
Plastic polysulfone enclosure,
IP66,123 x 48 x 46 mm (4.84 x
1.89 x 1.81 in)
Display
LCD dot matrix, 128 x 64 dpi
LCD 4-digit, 7 segment
LCD 4-digit, 7 segment
Display Accuracy
D.O.: 0.5% of reading
Temp.: ±1.0°C
0.01 ppm
0.1 ppb in 0-20 ppb range
1.0 ppb in 0-200 ppb range
Control Capabilities
/Advanced Features
0° to 60°C (32° to 140°F)
-20° to 60°C (-4° to 185°F)
-20° to 60°C (-4° to 185°F)
Operating Conditions
PID control; Pocket PC and infrared
configuration; ppb or ppm
measurement, automatic or manual
calibration; temperature and pressure
compensation,Ethernet/Modbus
communications,
E. European languages
Integral electronics/sensor design
Integral electronics/sensor
design
Operating Voltage
90-264 Vac; 47-63 Hz
16-42 Vdc
16-42 Vdc
Analog Outputs
Up to three 4 to 20mA
One (1) 4 to 20 ma
One (1) 4 to 20 ma
Relays
Up to 4 relays
Pipe, wall, or panel
N/A
N/A
Integral, no electronics mounting needed Integral, no electronics mounting
Remote: pipe, wall or DIN rail
needed
Remote: pipe, wall or DIN rail
CE; FM Class 1, Div. 2;
UL/CSA General Purpose
UL and CSA general purpose
Mountings
Approvals
Sensor
DL5000 Equilibrium Probe
for ppm & ppm application
Measurement Range
0-20,000 ppb or 0-20 ppm
Temperature Range
Pressure and
Temperature Ratings
2° to 60°C (35.6° to 140°F)
316SS: 50 psi (345 kPa)
CPVC: 30 psi (207 kPa)
Materials of Construction
316SS or CPVC housing
Special Features
Equilibrium probe design
requires no internal probe
maintenance
Mountings
Immersion in tank, in-line
or sample flow chamber
Dimensions (OD)
219 x 34 mm (8.62 x 1.32
in),1 inch NPT pipe size, 20
feet waterproof cable
Response Time
85% in 60 seconds
UL and CSA general purpose
CENELEC
These analyzers/probe systems determine the levels of dissolved
oxygen in water. The patented equilibrium dissolved oxygen probe
design is unaffected by inert fouling or changes in flow conditions.
The system’s analyzer/controller measures either ppb DO levels in
power plant and semiconductor applications
for corrosion detection or dearator efficiency or
ppm DO levels in wastewater, environmental and process
applications for control and compliance.
PT CONTROMATIC PRIMA MANDIRI
Page 09
Analytical Instruments
GAS ANALYZERS
greater value and enhanced performance
Thermal Conductivity
A thermal conductivity system that measures
concentrations of hydrogen purity and CO2 gas. This
measurement is typically made in hydrogen-cooled
generators.
7866 Digital Thermal Conductivity Analyzer
The 7866 Thermal Conductivity Analyzer is designed to
provide a highly sensitive and accurate analysis of a binary
(2-component) mixture of gases.
The analyzer can also be calibrated to measure a
single component of a multicomponent gas mixture,
providing the background gases constitute a stable mixture
(such as air), or have approximately the same thermal
conductivity. It uses the principles of
thermal conductivity, to determine the concentration of a
sample gas through the measurement of thermal losses
from two highly stable, matched thermistor probes inserted
in a stainless steel block.















Easy to use prompts
Security code protected
Reliable solid state design
High speed of response
High sensitivity
Excellent stability
Low maintenance requirement
Low installation costs through optional remote mounting
capability of the sensing unit (transmitter)
Explosion-proof housing on the sensing unit available for
Class1, Div1 areas
Signal transmission from the sensing unit up to 1000 feet
over unshielded lead wires
Panel-mounted 1/4 DIN control unit with easy-to-read
display
Current output signal from the control unit representing
measured PV
Single or dual alarms
A triple range analyzer for hydrogen-cooled generator
applications is available
Optional Modbus communications supports configuration
and data acquisition
7872 Gas Sampling System
The pre-packaged 7872 sampling system provides a
complete pre-engineered panel designed specifically for
hydrogen cooled generator applications in utility, paper mills
and other co-generation applications.
The sampling system allows easy, convenient
calibration of all three ranges.
The 7872 sample panel is an optional part of the 7866
analyzer and includes all components mounted on a single
steel panel.
Components of the sampling system include:





Flow Control Module
Calibration Module and Bypass Module
Pressure Regulator
Air Filter
Rugged Stainless Steel Tubing, Valves and Fittings
Sampling System
Construction
7872 Sample Panel
12 gauge steel, enamel
finish, with components
mounted,piped and tested
1, 2 or 3 as specified
Dimensions (W x H x D)
Sample Requirement
(Sensing Unit)
0.2 to 4.2 cfh flow 37 mm
Hg Pressure min.
53.7 x 76.2 x 15.4 cm (21 x
30 x 6 in)
Weight (approx.)
50 lbs (22.5 kg)
Power Requirement
(Control Unit)
Universal 90 to 264 Vac, 50
to 60 Hz
Calibrating Gases
CO2, H2 and 75% H2 in
N2
Weight
(Sensing Unit/Control Unit)
8.5 kg (18 3/4 lb)/1.3 kg
(3.0 lbs)
Sample Temperature
Up to 104°C (220°F)
Sample Pressure
1 to 100 psig (6.9 to 69
kPa)
H2 Purity Gas Analyzer
Accuracy
7866 Analyzer
±2% of span
Response Time (for H2)
Initial, <1 sec 63%,13 sec,
90%, 23 sec, 99%, 40 sec
Measuring Range
PT CONTROMATIC PRIMA MANDIRI
Page 10
Controllers
UNIVERSAL DIGITAL CONTROLERS
Simple to install, easy to configure and easy to operate
Universal Digital Controllers
DC 1000
Product Description
DC 1000 family of microprocessor based
The UDC 700 is a 1/32 DIN format, OEM
controllers combine a high degree of functionality controller designed for a large number of
and reliability at a very low price in 4 different DIN applications.
sizes.
UDC 700
RS485 Modbus
The UDC 1200 provides a high degree of
functionality and reliability in a small format
(1/16 DIN) at a very low price. A limit control
model is also available.
Front Face Format
48 x 48 mm (1.89 x 1.89 in)
48 x 96 mm (1.89 x 3.78 in)
72 x 72 mm (2.83 x 2.83 in)
96 x 96 mm (3.78 x 3.78 in)
49 x 25 mm (1.93 x 0.98 in)
48 x 48 mm (1.89 x 1.89 in)
Analog Inputs
1 or 2
1
1
Input Signal Types
Thermocouples, RTDs, mV, V, mA
Thermocouples, RTDs, mV, mA
Thermocouples, RTDs, mV, V, mA
Digital Inputs
N/A
N/A
1
Analog Outputs
Up to 2
N/A
Up to 3
Digital Outputs Control
Up to 2
Up to 2
Up to 2
Digital Outputs Alarm
Up to 3
Up to 2
Up to 2
Accuracy (at ref. cond.)
±0.5% of F.S.
±0.1% of span
±0.1% of span
Loops
1
1
1
Networking
Rs232 or RS485 ASCII
Rs485 Modbus
Rs485 ASCII or Modbus
ACCUTUNE™ II with Fuzzy Logic (Available on the UDC
2500, UDC 3200 and UDC 3500 Controllers)
Accutune II provides a new truly plug-and-play tuning
algorithm which will, at the touch of a button or through a
digital input, accurately identify and tune any process
including integrating processes and those with dead-time.
This speeds up and simplifies startup, plus allows retuning
at any setpoint. Also
included is the original Accutune adaptive
tuning algorithm that can automatically and
continuously retune whenever a setpoint
step change is implemented or whenever a
process variable disturbance occurs.
included is the original Accutune adaptive tuning algorithm
that can automatically and ontinuously retune whenever a
setpoint step change is implemented or whenever a
process variable disturbance occurs.
Fuzzy logic is used to suppress process
variable overshoot due to setpoint changes or externally
induced process disturbances. It operates independently
from Accutune tuning. It does not change PID constants, but
temporarily modifies the internal controller response to
suppress overshoot.
Fuzzy logic is used to suppress process variable overshoot
due to setpoint changes or externally induced process
disturbances. It operates independently from Accutune
tuning. It does not change PID constants, but temporarily
modifies the internal controller response to suppress
overshoot.
This allows more aggressive tuning to co-exist with smooth
process variable responses. It can be enabled or disabled
depending on the application or the control criteria.
This allows more aggressive tuning to co-exist with smooth
process variable responses. It can be enabled or disabled
depending on the application or the control criteria.
PT CONTROMATIC PRIMA MANDIRI
Page 11
Controllers
UNIVERSAL DIGITAL CONTROLERS
Simple to install, easy to configure and easy to operate
Universal Digital Controllers
UDC 1700
UDC 2500
UDC 3200
UDC 3500
Product Description
The UDC 1700 is a 1/8 DIN
microprocessor based controller.
It provides high quality and
performance at low cost
The UDC 2500 is a low-cost
digital controller providing
multi-language prompts
(FR, EN, GE, IT, SP) and code for
unmatched operating simplicity
The UDC 3200 is a 1/4 DIN
general purpose digital controller
offering a high degree of
functionality and operating
simplicity model is also available.
The UDC 3500 with dual loop
and math capability is ideal
for process applications
Front Face Format
48 x 96 mm (1.89 x 3.78 in)
96 x 96 mm (3.78 x 3.78 in)
96 x 96 mm (3.78 x 3.78 in)
96 x 96 mm (3.78 x 3.78 in)
Analog Inputs
1
1 high level, 1 universal
2 universal
4 high levels, 1 universal
Input Signal Types
Thermocouples, RTDs, mV, V, mA
Thermocouples, RTDs, mV, V, mA,
RH, Radiamatic
Thermocouples, RTDs, mV, V, mA,
RH, Radiamatic, carbon, oxygen
Thermocouples, RTDs, mV, V, mA,
RH, Radiamatic, carbon, oxygen
Digital Inputs
1
2
2
4
Analog Outputs
Up to 3
2 (4 to 20 mA)
2 (4 to 20 mA)
3 (4 to 20 mA)
Digital Outputs Control
Up to 2
Up to 2
Up to 2
Up to 4
Digital Outputs Alarm
Up to 2
Up to 2
Up to 2
Up to 4
Accuracy (at ref. cond.)
±0.1% of span
±0.25% of span
±0.2% of span
±0.10% of span
Loops
1
1
1
2
Networking
Rs485 ASCII or Modbus
Ethernet or Modbus RTU
Ethernet or Modbus RTU
Ethernet or Modbus RTU
Infrared Port
Yes
Yes
Yes
Yes
Honeywell Controller Value
Process Instrument Explore (P.I.E.) Software
Every Honeywell Controller, Programmer and Indicator
offers you the best price/performance ratio compared with
any competitive instrument in its class.
P.I.E. is a PC based, intuitive software program that runs on
a Pocket PC, desktop or laptop. It can be used either online
or offline to create UDC2500, UDC3200 and UDC3500
configurations.
Our complete line is engineered to provide you with
“targeted functionality”–solutions tailored to your specific
process control requirements–so you only buy what you
need.






Clear and informative operator interface
Easy to setup and operate
Straightforward installation and maintenance
Single-button turning for precise control
Fuzzy logic overshoot suppression
Unsurpassed quality and support
Configurations can be easily downloaded to the
controller via its communication or infrared port.
Process Instrument Explore (P.I.E.) Software
Each UDC2500, UDC3200 and UDC3500 has an infrared
communications port that provides a non-intrusive
connection to the controller while maintaining Type 4X and
IP66 integrity.
You can duplicate an instrument’s configuration, obtain
maintenance information just by pointing your Pocket PC in
the direction of the instrument.
PT CONTROMATIC PRIMA MANDIRI
Page 12
Programmers and Indicators
DIGITAL CONTROLLER PROGRAMERS AND INDICATORS
Simple to install, easy to configure and easy to operate
Digital Controller
Programmers
DCP 50
DCP 100
DCP 300
DCP 550
Product Description
The low-cost DCP 50 is ideal for
set point programming
applications where space is
at a premium.
The low-cost, ¼ DIN format DCP
100 programmer is an entry-level
product in the Set Point Programmer
range. It provides an attractive price/
performance ratio.
The general-purpose DCP
300 programmer is fully
dedicated to execute control of
temperature, humidity, pressure,
flow and other variables.
The high-performance DCP 550
programmer provides advanced
setpoint programming, sensing,
SP generation, ramp and soak
switching and timing in one unit.
Front Face Format
48 x 48 mm (1.89 x 1.89 in)
96 x 96 mm (3.78 x 3.78 in)
96 x 96 mm (3.78 x 3.78 in)
144 x 144 mm (5.67 x 5.67 in)
Programs
4
8
19
99
Segments Per Program
16
16
30
99 (2000 total max)
Analog Inputs
1
1
1 or 2
1 or 2
Analog Outputs
Up to 3
6
12
16
Digital Outputs
Up to 2
Up to 3
Up to 3
Up to 3
Accuracy (at ref. cond.)
Up to 2
8
8
16 events
Accuracy (at ref. cond.)
±0.1% of span
±0.25% of span
±0.1% of span
±0.1% of span
Loops
1
1
1 or 2
1 or 2
PID Group
1
1
8
9
Networking
RS485 Modbus
Rs485 ASCII or Modbus
-
Rs485 ASCII
Programmers
Product Description
DCP 200
¼ DIN format, a graphic/text LCD
display is an affordable temperature
and process controller with
advanced functionality including
profiling and datalogging options.
Indicators
Product Description
UDC 703
The UDC 703 is a 1/32 DIN
format indicator for small space
requirements.
UDI 1700
The UDI 1700 is a horizontal,
1/8 DIN format, low-cost indicator
for most process variable types.
Front Face Format
96 x 96 mm (3.78 x 3.78 in)
Size (L x H x D)
48 x 25 x 100 mm
96 x 48 x 100 mm
Programs
64
Accuracy
±0.10% of span
±0.10% of span
Segments Per Program
255
Analog Inputs
1 universal
1 universal
Analog Inputs
1
Input Signal Types
Thermocouples, RTDs,
Thermocouples, RTDs,
Digital Inputs
1
Display Types
4 digits-LED (red)
4 digits-LED (red)
Analog Outputs
2
Alarm Set Points
2
3
Digital Outputs
8
Digital Input
No
Yes
Accuracy
0.1%
Transmitter Power
No
Yes
Loops
1
Networking
Rs485 Modbus
Rs485 ASCII or Modbus
PID Group
1
Networking
RS232, RS485, Ethernet
PT CONTROMATIC PRIMA MANDIRI
Page 13
Recorders and Data Acquisition
Circular and Strip Chart Recorders
Dependable, versatile and low maintenance
Circular Chart Recorders
Honeywell Circular Chart Recorders are preferred for batch
processes. The circular chart record displays the
entire batch operation over a specific unit of time,
from one hour to 31 days.
An additional advantage of the circular chart record is easy
filing and copying for reference. Compared to the strip chart
record, the circular chart has a shorter calibrated chart
width.
Circular Chart Recorders
DR4300 Basic
Dr4300
DR4500 Classic
DR4500 Truline
Chart Size
254 mm (10 in)
254 mm (10 in)
305 mm (12 in)
305 mm (12 in)
Reference Accuracy
0.35%
0.20%
0.10%
0.10%
Analog Inputs
2
2
2
4
Digital Display
N/A
Yes
Yes
Yes
Chart Type
Preprinted
Preprinted
Preprinted
Self-printing thermal paper
Control
N/A
2 loops
2 loops
2 loops
Math
N/A
Totalization
Ye
Yes
Networking
N/A
Modbus RTU
Modbus RTU
Modbus RTU
Optional Software
N/A
Trend Manager Pro/Specview
Trend Manager Pro/Specview
Trend Manager Pro/Specview
Strip Chart Recorders
Honeywell Strip Chart Recorders are most
commonly chosen for continuous
processes where the chart record allows the
operator to quickly detect
out-of-tolerance deviations over a long-term trend.
Strip Chart Recorders
DPR180
DPR250
Display
Digital
254 mm (10 in)
Paper Width
180 mm (7.09 in)
0.20%
Reference Accuracy
0.05%
2
Multipoint Channels
24
Yes
Continuous Pens
N/A
Preprinted
Roll or Fan-Fold Charts
Yes
2 loops
Configuration
PC or Keyboard
Totalization
Data Storage
PCMCIA; Compact Flash
Modbus RTU
Networking
ASCII, Modbus, RTU
Trend Manager Pro/Specview
Optional Software
Trend Manager Pro/Specview
Trend Manager Pro/Specview
The long length of the strip chart allows recorders to
run unattended for long periods without the
necessity for frequent chart replacement. For
corrosion detection or dearator efficiency or ppm DO
levels in wastewater, environmental and process
applications for control and compliance.
PT CONTROMATIC PRIMA MANDIRI
Page 14
Recorders and Data Acquisition
Paperless Recorders and Data Acquisition
Electronic data for improved decision-making
Paperless Recorders
eZtrend QXe
Minitrend QX
Multitrend SX
Displays
127 mm (5.0 in) Color (QVGA)
140 mm (5.5 in) Color TFT (QVGA)
307 mm (12.1 in) Color (SVGA)
Analog Inputs
Up to 12
Up to 16
Up to 48
Data Storage
USB Memory Key
Compact flash/USB Memory Key
Compact flash/USB Memory Key
Sample Rate
100/200/500ms
20/100/200/500ms
20/100/200/500ms
Digital I/O
Up to 8DI/8DO
Up to 16DI/16DO
Up to 48DI/48DO
Networking
Ethernet/RS485, OPC Server, Web
Ethernet/RS485 Modbus, OPC Server, Web
Ethernet/RS485 Modbus, OPC Server, Web
Math Functions/Math Scripts
Yes/No
Yes/Yes
Yes/Yes
Reference Accuracy
±0.1% Typical-TC
±0.1% Typical-TC
±0.1% Typical-TC
Configuration
PC or front panel
PC or front panel
PC or front panel
Remote Viewing
Internal Web Page
Internal Web Page
Internal Web Page
PT CONTROMATIC PRIMA MANDIRI
Page 15
Wireless Solutions
ONEWIRELESS FIELD DEVICES
Simple and efficient network that enables increased safety, reliability and efficiency
XYR 6000 Transmitters
XYR 6000 transmitters provide highly accurate pressure,
temperature, analog input, valve position, digital input
measurements or a digital output, and transmit the
measured value wirelessly using the 2.4 GHz ISM band
and ISA100.11a open protocol to a Honeywell
Mutinode or Field Device Access Point gateway.
XYR 6000
transmitters provide the ability to obtain data from remote
and hazardous measurement locations without the need to
run wires.
Transmitters
XYR 6000 Transmitters (condensed specifications)
Radio Frequency:
2.4Ghz, License Free, Direct Sequence Spread Spectrum (DSSS) Technology; ISA100.11a Compliant
Sensors Radio Power:
125-400 mW
Range:
305 m (1000 ft) with Integral 2 dBi Antenna
Transmitter Power:
2 “D” size 3.6 V Li - Non Rechargeable Batteries
Battery Life:
Up to 10 years
Diagnostics:
Extensive Device Status Capability
Wireless Solutions:
OneWireless Compatible and ISA100 Compliant
Software:
Local and Software Configurable
LCD Display:
Local, Alpha Numeric, 8 Segment, Always On
Operating Temperature:
-40° to 85°C (-40° to 185°F)
Hazardous Approvals:
FM, CSA, ATEX, IECEx, InMetro, SAEx
Enclosures:
NEMA Type 4X, IP 66/67 and NEMA 8 (Explosion Proof), Stainless Steel Housing Available
Connection:
Optional 4dBi Integral, Remote 8 dBi Omni Directional or 14dBi Directional antennas
Differential Pressure
Ranges:
400” H2O (1,000 mbar), 100 psi (7,000 mbar),3000 psi (210,000 mbar)
Gauge Pressure
Ranges:
500, 3000, 6000 and 10,000 psi (35, 210, 415 and 690 bar) In-Line Meter Body; 500 and 3000 psi,
Absolute Pressure
Ranges:
500 psia (35 barA)
Flange Mount:
Ranges:
400” H2O (1000 mbar), Pseudo Flange, 100 psi (7000 mbar)
Remote Seal:
Ranges:
400” H2O (1000 mbar), 100 psi (7000 mbar) DP; 500 psi (35 bar), 3000 psi (210 bar) GP; 500 psia (35
Temperature/DI
Remote Probe:
Analog Input
Temperature + DI; 3 TC Max, 2 RTD Max, 3 DIs Max
4-20 or 0-20ma/0-5 or 1-5V
Accuracy:
±0.10%
Discrete Inputs :
Three Inputs; Dry Contact Only, No Voltage or Current; 1 Kohm Maximum Impedance
Position:
Provides position monitoring for items like linear distances or valve position
Acoustic:
Not Available
Base Radio:
FDAP, Multinode/Gateway; 2-802.11 a/b/g (Wifi/Wireless Ethernet)
1-(ISA100 Compliant) Sensor Radio
2-Ethernet Cables for Optional Connections to Wired Devices
Power:
24 VDC ±10% at 25 Watts; -40° to 75°C (-40° to 167°F); IP 66, NEMA 4X Enclosure;
Class 1 Div2/ATEX Zone II Certified; Integral and Remote Antennas Available
PT CONTROMATIC PRIMA MANDIRI
Page 16
Modular Systems
HC 900 CONTROL SYSTEM
modular solutions for diverse control requirements
HC900 Controller
The rack-based HC900 is a modular, scalable platform
available in 3 rack sizes (4, 8 and 12 I/O slots) and three
CPU performance choices (C70R, C50, C30) to handle a
wide range of automation requirements.
The CPU options available for the HC900 Controller
include: C30 and C50 for non-redundant applications; C70
for redundant networking; C70R for redundant CPU
applications and redundant networking. To maximize
installation flexibility, up to 4 remote I/O racks may be
connected to a single controller to reduce wiring and
installation costs.
This C50 and C70 CPU supports a single direct connected
remote rack or up to 4 remote racks when connected
through an external Ethernet switch. The C70R CPU
supports a single direct connected rack or up to 5 remote
racks using external switches.
A variety of analog and digital modules are available to
support up to a total of 1920 I/O points. Up to 480 universal
analog inputs minimize the number of input cards and
spare parts required.
The versatile HC900 Controller is the perfect solution for
unit control requiring integrated loop and logic processing.
It is also the ideal data acquisition package with up to 480
universal analog inputs, extensive math and free form
calculations.
Intuitive function block software allows you to quickly get up
and running, saving you time and money. Ethernet Open
Connectivity simplifies plant network integration.
Redundant CPU’s, Power Supplies and Networks maximize
process uptime.
The HC900 offers an integrated solution that costeffectively performs loop and logic control of stand-alone,
unit processes.
The combination of analog control loops, setpoint
programs, function block configuration, data acquisition and
an extensive assortment of predefined analog and digital
blocks make the HC900 the ideal choice for thermal
processing, water treatment, food & beverage
processing, power generation, pharmaceutical,
manufactured goods, semiconductor industries and other
HC900
Controller
Analog Inputs
Up to 480 universal analog inputs, 960 high level
Accuracy
±0.1% of span (field calibration to ±0.05% of span)
Analog Outputs
Up to 200; user specified span from 0 to 20 mA maximum,
12 bits, 0.1% Accuracy
Digital Inputs/Outputs
Up to 1920, contact DI, 24 Vdc DI/DO
Function Blocks
C70, C70R CPU-5000; C50 CPU-2000; C30 CPU-400
I/O Racks Per System
Up to 5 total
Control Loops
PID, on/off, cascade, ratio, %C, RH, dewpoint
Control Output Types
Current, time-proportioning, position proportioning,
three-position step
 Process
Setpoint Programmers
50 segments each, 16 event outputs, profiles stored in
controller
Setpoint Scheduler
50 segments, 8 ramp/soak outputs, 8 auxiliary outputs,
16 events, schedules stored in controller
 Universal analog inputs
 Stores setpoint profiles,
Recipes
50 variables each
 Remote Terminal Panels
Communication
Ethernet 10baseT; Modbus/TCP protocol; up to 5 Ethernet
hosts; up to 32 peer to peer controllers; Serial Modbus
RTU,RS485 or RS232, Slave (up to 16) or master operation
 Redundant CPU’s, power
Power Supply
120 Vac to 240 Vac or 24Vdc
Operating Temp.
0° to 60°C (0° to 140°F)
Humidity
10% RH to 90% RH, non-condensing
Rack Size
4 Slot
8 Slot
12 Slot
266.7 mm (10.5 in) 419.1 mm (16.5 in) 571.5 mm (22.5 in)
Controller:
Control Designer Software:
 Modular I/O design
 Multiloop PID Control
 Setpoint


programmers,scheduler

 Process logic, timers,
counters

algorithms,calculations
recipes
(RTP)
supplies



Windows Vista, XP SP2
Professional support,
Windows 7
Drag and drop soft wiring
of function block objects
Load configuration via
ethernet, serial
communication modem
Graphic hard copy
records
Load/upload, monitor
configuration via modem
Database export in CSV
or TAB DELIMITED
formats
PT CONTROMATIC PRIMA MANDIRI
Page 17
Modular Systems
HC 900 CONTROL SYSTEM
modular solutions for diverse control requirements
Operator Interface
Model 900CS10-00
Model 900CS15-00
Display
Size: 264 mm (10.4 in)
Pixels: 640 X 480; Color LCD
381 mm (15 in)
Pixels: 1024 X 768 Color LCD
Data Logging
Media: Volatile RAM memory,
optional non-volatile flash card
memory or removable USB
memory module, Secure Data
Archiving; Data Types: Process
history, alarms, events,
diagnostics, user changes;
Export format: CSV
Media: Volatile RAM memory,
optional non-volatile flash card
memory or removable USB
memory module, Secure Data
Archiving; Data Types: Process
history, alarms, events,
diagnostics,user changes;
Export format: CSV
Power Supply
+24 VDC ±20% @ 29 W max.
Requires Class 2 or SELV
rated power supply. Front
panel LED indication of power
on
+24 VDC ±20% @ 46 W max.
Without options. Requires
Class 2 or SELV rated power
supply. Front panel LED
indication of power on
Safety
ANSI/UL 61010-1 – 2005,
Second Edition. General
Purpose (Ordinary Location)
Safety. UL evaluated to CSA
C22.2 No. 61010-1-2004Second Edition. General;
Purpose (Ordinary Location)
Safety; UL, CSA and FM Class
I, Div 2 Groups A,B,C and D Hazardous (Classified;Location
Safety for USA and Canada
ANSI/UL 61010-1 – 2005,
Second Edition. General
Purpose (Ordinary Location)
Safety; UL evaluated to CSA
C22.2 No. 61010-1-2004Second Edition; General
Purpose (Ordinary Location)
Safety; UL, CSA and FM Class
I, Div 2 Groups A,B,C and D Hazardous(Classified);Location
Safety for USA and Canada
Operating
Operating Temperature Range:
0 to 50°C (32 to 122°F)
Storage Temperature Range:
Operating Temperature Range:
0 to 50°C (32 to 122°F)
Storage Temperature Range:
Humidity
Operating and Storage
Humidity: 80% maximum
relative humidity
(non-condensing) from 0 to
50°C. -20 to 70°C (-4 to 158°F)
Operating and Storage
Humidity: 80% maximum
relative humidity
(non-condensing) from 0 to
50°C.-20 to 70 °C (-4 to 158°F)
HC900 Controller
Operator Interface
The 900 Control Station operator interface from Honeywell
compliments the HC900 Controller with a unique
combination of predefined display features and custom
display development tools to deliver ease of use and high
flexibility in an efficient and affordable package.
The color display and finger touch user interface enhances
process monitoring while simplifying online controller
changes. The Station Designer software used to configure
the interface works in conjunction with the Hc900 Hybrid
Controller configuration software to automatically build a
Control Station database that exactly matches the unique,
user configured, controller database.
This highly integrated operation eliminates the time
consuming task of assigning controller communication
register addresses to the operator interface parameters
used to build displays. The standard database of the
Control Station allows all available controller tags to be
imported without restriction or costly price adders,
eliminating the risk of running out of tag resources in the
middle of your project.
The hardware of the 900 Control Station is designed to
handle tough industrial environments with a full metal case
design and water tight, type 4X, front bezel assembly.
Hardware push buttons on the front panel supplement
touch screen software buttons for common interface tasks
such as user log-off, display last screen and main menu
access.
The 900 Control Station is available with either a 10.4 inch
or 15 inch display size. Both models are configured using
Station Designer PC configuration software.
Communications:
Operator Interface:
 Modbus/TCP Protocol
 USB Ports: Adhere to
 Fully manage HC900





USBspecification 2.0
RS232 Serial Ports (RJ12
connectors)
RS485 Comm. Port (RJ45
connector)
Ethernet Port: (RJ45
connector)–wired as a NIC
(Network Interface Card)
10 BASE-T/100 BASE-TX
Redundant Networks












controllerfunction blocks
such as PID, setpoint
programmers, etc.
Load/monitor setpoint
programs, recipes
View analog and digital
status
View bar graph groups
View trends
View alarm and event
status
Initiate operator pushbuttonactions
Expandable memory with
Flash Memory socket for
record keeping &
configuration transfer
Configuration stored in
non-volatile memory for
secure operation
Integrate HC900
controller alarms/events
or build them into the
interface
Emulator
Multilingual (5 languages
including English,
German, French, Spanish
and Italian)
Batch Reporting
PT CONTROMATIC PRIMA MANDIRI
Page 18
Actuators
HERCULINE
Smart design for lower cost of ownership
HercuLine Electric Actuators
HercuLine 2000
HercuLine 2001 / HercuLine 2002
HercuLine 10260A / HercuLine
10260S
Product Description
Low torque electric actuator
Low torque electric actuator
Torque
50 to 400 in-lb (6 to 45 N-M)
50 to 400 in-lb (6 to 45 N-M)
Medium torque industrial electric
actuator
10 to 300 lb-ft (14 to 400 N-M)
Stroke/Speed
90° to 150°/6 to 75 sec
90° to 150°/7.5 to 120 sec
90°/10/20/40/60 sec
Input Signals
Floating, Pos. prop., Open/Close
1-5 Vdc, 4 to 20 mA
0/1-5 Vdc, 0/4-20 mA, Floating,
Pos. prop., Open/Close
Position Feedback
1000 ohms potentiometer
0/1-5 Vdc, 0-16 Vdc,
0/4-20 mA, SW emulation
0/1-5 Vdc, 0-16 Vdc, 0/4-20 mA, SW
emulation 1000 ohms potentiometer
Position Sensing
1000 ohms potentiometer
2001: slidewire
2002: contactless
Contactless
Environmental
-40° to 85°C (-40° to 185°F)
-40° to 75°C (-40° to 170°F)
-30° to 75°C (-20° to 170°F)
Duty Cycle
Continuous
Continuous
Continuous
Repeatability
N/A
0.2% of 90° span
0.2% span
Dead-Band
N/A
Adj. 2% to 5% span
Adj. 0.2% to 5% span
Local Auto/Man Switch
Optional
Optional
Optional
Local Keypad/Display
N/A
Optional
10260S: Optional
Rs485 Modbus Comms.
N/A
Yes
10260S: Yes
HercuLine Electric Actuators
HercuLine Electric Actuators are engineered for exceptional
reliability, accurate positioning, and low maintenance.
Designed for very precise positioning of dampers and
quarter-turn valves, they perform especially well in
extremely demanding environments requiring continuous
duty, high reliability and low maintenance. With non-contact
sensing, the maintenance problems and unexpected
shutdowns associated with slidewires and potentiometer
wear are eliminated. configuration software.
HercuLine Smart Actuators
Honeywell’s new actuators incorporate all of the quality and
reliability features of the HercuLine actuators with the
added benefits of microprocessor-based electronics. These
benefits make it easier to install, set up and commission the
actuator, while allowing you to monitor the health
parameters for proactive maintenance planning.
 RS485/Modbus communications for remote access
 Programmable: Alarm and relay outputs;
Characterization, failsafe functions, dead-band, and
filtering; Direction of rotation
 Diagnostic Parameters: Maximum Hi and Lo
temperature; Stall and accumulated stall time; Total
travel
Honeywell Actuator Linkage Software
Helps you size, select and install your Honeywell actuator.
The software lets you choose the actuator and design the
linkage that best fits your application.
HercuLine PC Software
 Lowers ownership cost
 Use your PC for calibration, configuration and
maintenance data
 Eliminates local display and keypad
PT CONTROMATIC PRIMA MANDIRI
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement