SKF Microlog Analyzer Accessories Catalog

SKF Microlog Analyzer Accessories Catalog
SKF Microlog Analyzer
Accessories Catalog
Foreword
Unmatched versatility, reliability and functionality have made the SKF Microlog Analyzer
series of data collectors the premier choice for portable, handheld condition monitoring
units.
Designed to help users establish or upgrade an existing condition monitoring program,
SKF Microlog Analyzers handle the tasks required to perform predictive maintenance on
rotating machinery in countless industries.
Data capture from a range of sources
SKF Microlog Analyzers automatically collect both dynamic (vibration) and static (process)
measurements from almost any source, including handheld and magnetically mounted
accelerometers, permanently mounted vibration sensors or on-line monitoring systems.
Temperature measurements can be collected with a non-contact infrared sensor or with a
contact probe.
State-of-the-art operating technology
With robust, high-speed data processors and optimum data storage capacity, SKF Microlog
Analyzers are equipped to operate within today’s most advanced computerized maintenance
management systems. Units can be purchased with a range of individual modules and
accessories for specific types of analysis required to meet their plant’s monitoring needs.
2
Product compatibility
SKF Microlog models
Every product listed in this catalog contains a legend that shows
which SKF Microlog models are compatible with that product. An
example of the legend is shown below. For example, a product that
contains the legend below would be compatible with SKF Microlog
models CMXA 48 and CMXA 80.
The accessories in this catalog are applicable to the following
SKF Microlog models:
CMXA 45
CMXA 45/75-Z2
•
CMXA 48
CMXA 48/80-Z2
Compatible
SKF Microlog
models
CMXA 51-IS
CMXA 70/44
CMXA 75
•
CMXA 80
Example of
compatibility legend
Note: The “CMXA 45/75-Z2” designation in the legend refers to
both CMXA 45-Z2 and CMXA 75-Z2 ATEX Zone 2 certified models.
The “CMXA 48/80-Z2” designation in the legend refers to both
CMXA 48-Z2 and CMXA 80-Z2 ATEX Zone 2 certified models.
• CMXA44: SKF Microlog Analyzer MX series
• CMXA45: SKF Microlog Advisor Pro
• CMXA45-Z2: SKF Microlog Advisor Pro, certified for use in
ATEX Zone 2 hazardous areas
• CMXA48: SKF Microlog Consultant
• CMXA48-Z2: SKF Microlog Consultant, certified for use in
ATEX Zone 2 hazardous areas
• CMXA51-IS: SKF Microlog Analyzer, certified for use in
intrinsically safe (IS) areas
• CMXA70: SKF Microlog Analyzer GX series
• CMXA75: SKF Microlog Analyzer GX series
• CMXA75-Z2: SKF Microlog Analyzer GX series, certified for use in
ATEX Zone 2 hazardous areas
• CMXA80: SKF Microlog Analyzer AX series
• CMXA80-Z2: SKF Microlog Analyzer AX series, certified for use in
ATEX Zone 2 hazardous areas
Note: For use of accessories in hazardous areas, reference the
product safety instructions. Accessories listed as compatible with the
CMXA 45/75/48/80 models may also be used with the
corresponding Z2 (ATEX Zone 2 certified) models in areas known to
be non-hazardous. Please consult your site safety officer for
clarification.
Accessories for discontinued SKF Microlog
models
For a list of accessories available for discontinued SKF Microlog
models, refer to the section Accessories for obsolete products
(† page95).
3
4
Contents
Accelerometers
9
Cables
27
Hardware
45
Power
69
Miscellaneousaccessories
75
5
SKF – the knowledge engineering
company
From one simple but
inspired solution to
a misalignment
problem in a textile
mill in Sweden, and
fifteen employees in
1907, SKF has
grown to become a
global industrial
knowledge leader.
Over the years we have built on our expertise in bearings, extending it to seals, mechatronics, services and lubrication systems.
Our knowledge network includes 46 000
employees, 15 000 distributor partners,
offices in more than 130 countries, and a
growing number of SKF Solution Factories
around the world.
Meeting the toughest challenges
Working for a sustainable future
Our network of knowledge and experience
along with our understanding of how our
core technologies can be combined helps
us create innovative solutions that meet the
toughest of challenges. We work closely with
our customers throughout the asset life
cycle, helping them to profitably and
responsibly grow their businesses.
Since 2005, SKF has worked to reduce the
negative environmental impact from our
own operations and those of our suppliers.
Our continuing technology development
introduced the SKF BeyondZero portfolio
of products and services which improve
efficiency and reduce energy losses, as well
as enable new technologies harnessing
wind, solar and ocean power. This combined
approach helps reduce the environmental
impact both in our own operations and in
our customers’.
Research and development
We have hands-on experience in over forty
industries, based on our employees’ knowledge of real life conditions. In addition our
world-leading experts and university partners who pioneer advanced theoretical
research and development in areas including tribology, condition monitoring, asset
management and bearing life theory. Our
ongoing commitment to research and
development helps us keep our customers
at the forefront of their industries.
SKF Solution Factories make SKF knowledge and manufacturing expertise
available locally, to provide unique solutions and services to our customers.
6
Working with SKF IT and logistics systems and application experts, SKF
Authorized Distributors deliver a valuable mix of product and application
knowledge to customers worldwide.
Working closely with you
Our objective is to help our customers
improve productivity, minimize maintenance, achieve higher energy and resource
efficiency, and optimize designs for long
service life and reliability.
Innovative solutions
Whether the application is linear or rotary
or a combination of the two, SKF engineers
can work with you at each stage of the asset
life cycle to improve machine performance
by looking at the entire application. This
approach doesn’t just focus on individual
components like bearings or seals. It looks
at the whole application to see how each
component interacts with the next.
an
d
dc
om
m
ai
n
ission
SKF Life Cycle
Management
st
te
SKF Life Cycle Management is how we combine our technology
platforms and advanced services, and apply them at each stage
of the asset life cycle, to help our customers to be more
successful, sustainable and profitable.
Man
ufa
ctu
re
an
int
Ma
Our knowledge
– your success
ion
at
d
Spec
ific
Design and develo
p
rep
air
Opera
te and monitor
n
la
tal
Ins
Bearings
SKF is the world leader in the design, development
and manufacture of high performance rolling
bearings, plain bearings, bearing units and
housings.
Machinery maintenance
Condition monitoring technologies and maintenance services from SKF can help minimize
unplanned downtime, improve operational
efficiency and reduce maintenance costs.
Sealing solutions
SKF offers standard seals and custom engineered
sealing solutions to increase uptime, improve
machine reliability, reduce friction and power
losses, and extend lubricant life.
Design optimization and verification
SKF can work with you to optimize current
or new designs with proprietary 3-D modeling software that can also be used as a virtual test rig to confirm the integrity of the
design.
Mechatronics
SKF fly-by-wire systems for aircraft and drive-bywire systems for off-road, agricultural and forklift
applications replace heavy, grease or oil consuming
mechanical and hydraulic systems.
Lubrication solutions
From specialized lubricants to state-of-the-art
lubrication systems and lubrication management
services, lubrication solutions from SKF can help to
reduce lubrication related downtime and lubricant
consumption.
Actuation and motion control
With a wide assortment of products – from actuators and ball screws to profile rail guides – SKF
can work with you to solve your most pressing
linear system challenges.
7
8
Accelerometers
Triaxaccelerometerkit,CMAC4370-K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Smallfootprintaccelerometerwithintegralcable,CMSS2111 . . . . . . . . . . . . . . . 12
Highfrequencyaccelerometerkit,CMSS2114-K . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Generalpurpose,lowprofile,sideexitindustrialaccelerometer,CMSS2200and
CMSS2200-M8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Intrinsicallysafe(IS)industrialaccelerometer,CMSS2210 . . . . . . . . . . . . . . . . . . 18
Smalldiameteraccelerometer,CMSS732A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
CSAapproved,generalpurposeindustrialaccelerometer,CMSS793-CA . . . . . . . 22
ATEXapproved,intrinsicallysafe(IS),generalpurposeindustrialaccelerometer,
CMSS793-EE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Mediumdutymagneticbase,CMSS908-MD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
9
CMAC 4370-K
•
Triax accelerometer kit
CMXA 45
CMXA 45/75-Z2
SKF’s triax accelerometer quickly and automatically measures horizontal, vertical and
axial (triaxial) data with the press of a button. Triaxial measurements offer the user
additional information on the condition of
machinery, enabling a more complete diagnostic analysis. For example, measuring in a
vertical direction often provides insight into
how the shaft is restrained when considering bearing looseness. A horizontal orientation is preferred for bearing fault diagnosis and an axial measurement can provide clues as to the severity of shaft misalignment.
The SKF Microlog can acquire data simultaneously from all three
axes. The triax accelerometer also enables measurement in any of
the three axes where, in specialized cases, a single point accelerometer would be unable to measure data due to physical mounting
restrictions or a difficult to access mounting surface.
For those who typically collect triaxial data, the sensor dramatically reduces data collection time. For users who up until now have
collected only one data point per sensor location, triax offers the
advantage of additional information for improved diagnostics. The
triax accelerometer facilitates the efficient collection of accurate and
repeatable machine date for enhanced decision making.
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
• Electrical noise: 0,0005 g, RMS
• Output impedance: 100 Ω
• Bias output voltage: 12 to 13 V DC
• Discharge time constant: 0,6 s
• Case ground isolation, signal/power ground pin to case: 10 MΩ
Environmental
• Temperature range: –55 to +120 °C (–65 to +250 °F)
• Vibration limit: 1 000 g, RMS
• Shock limit: 2 000 g peak
• Base strain sensitivity: 0,001 g/µ strain at 250/µ Ω
• Thermal coefficient of sensitivity: 0,05%/°C (0,03%/°F)
Physical
Specifications for triax accelerometer
Dynamic
• Sensitivity (±5%): 100 mVg
• Measurement range: 50 g, RMS
• Frequency range:
– ±5%: 0,5 to 3 000 Hz
– ±10%: 0,3 to 5 000 Hz
– ±3 dB: 0,2 to 10 000 Hz
• Amplitude non-linearity: ±1% full scale maximum
• Resonance frequency, mounted, nominal: 25 kHz
• Transverse sensitivity: ≤ 5%
Electrical
• Power requirements:
– Voltage source*: 18 to 30 V DC
– Constant current diode: 2 to 20 mA
*Do not apply power to this instrument without current limiting in the range
of 20 mA maximum. To do so will immediately destroy the integral amplifier. It is suggested that only SKF approved power units be utilized for
powering this instrument.
10
• Dimensions: See drawing
• Weight: 115 g (4.1 oz.)
• Mounting: Captive 1/4–28 mounting screw
• Case material: Aluminum alloy
• Sealing: Welded / glass to metal seal / O-rings, hermetic
• Connections:
– Coaxial, radically mounted
– Four pin MIL-C-26482, 8-4P
• Recommended magnetic base: CMSS 908-MD
Kit contents
• Triax accelerometer
• Anti-rotation pin mounted on the bottom surface of the sensor
(the anti-rotation pin can be carefully un-threaded from the
sensor so that it can be permanently mounted)
• CMAC 5009: Triaxial accelerometer cable
• CMAC 4300: Stud adapter
• CMSS 2620-3: Studs (three)
• Calibration certificate traceable to NIST
Dimensions
Model 6524, 1/4-28 mounting
screw. Mounting screw is detachable
Location of anti-rotation
pin viewed from above1)
10,3 mm
(0.41 in.)
2
3
30,2 mm (1.19 in.)
10-32 tapped hole for
calibration, typical two
places
M
EL
ER
O
AC
C
L
IA
AX
TR
I
S/N
41,3 mm
(1.63 in.)
3073M6
Triax accelerometer
ET
ER
1
Axis 2
Common ground2)
Pin D
53,8 mm (2.12 in.)
Axis 1
1)
Anti-rotation pin is a 4-40 socket
head cap screw, head diameter
4,65 mm (0.18 in.) maximum
2) Sig/Pwr ground return is isolated
from case by > 10 MΩ
a)
b)
Sig/Pwr
Axis 3
Pin C
Sig/Pwr Axis
1
Pin A
Axis #3
Model 6551
fiber washer
Torque mounting screw T-15 lb. in.
Axis arrowheads delineate sense
and direction of positive
acceleration for positive going
voltage
Sig/Pwr Axis
2
Pin B
24,1 mm
(0.95 in.)
25,4 mm
(1.00 in.)
CMAC 5009 triaxial accelerometer cable
Mounting surface
CMAC 4300 stud
adapter
CMSS 2620-3 stud
Optional accessories
CMAC 9600-01 toolkit for
1/4–28
Orderinginformation
stud
• CMAC4370-KTriax accelerometer kit. Each kit includes a triax
accelerometer, triax accelerometer cable, stud adapter and three
studs. A calibration certificate traceable to NIST is also supplied with
each instrument.
OptionalAccessories
• CMAC9600-01 Toolkit for 1/4–28 stud
• CMSS908-MD Medium duty magnetic base
11
CMSS 2111
•
Small footprint accelerometer with
integral cable
CMXA 45
CMXA 45/75-Z2
•
The CMSS 2111 is a small footprint accelerometer
that includes an integrated 2 m (6.56 ft.) cable along
with a magnetic mount (CMSS 908-LD). This accelerometer is capable of working to a depth of 5 m
(16.4 ft.) (additional cable length required).
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
Specifications
CMXA 70/44
CMXA 75
CMXA 80
Dynamic
• Sensitivity (±10%): 100 mVg
• Measurement range: ±50 g
• Frequency range (±3 dB): 0,5 to 10 000 Hz
• Non-linearity: ±1%
• Resonance frequency: 22 kHz
• Transverse sensitivity: ≤ 7%
Electrical
• Power supply:
– Voltage source: 18 to 28 V DC
– Constant current diode: 2 to 20 mA
• Electrical noise:
– Broadband:
· 1 Hz to 10 kHz: 350 µg
– Spectral:
· 10 Hz: 8 µg/√Hz
· 100 Hz: 5 µg/√Hz
· 1 kHz: 4 µg/√Hz
• Output impedance: < 150 Ω
• Bias output voltage: 8 to 12 V DC
• Discharge time constant: ≤ 0,3 s
• Settling time (within 1% of bias): ≤ 2,0 s
Environmental
• Temperature range: –55 to +120 °C (–65 to +250 °F)
• Shock limit: 5 000 g peak
• Enclosure rating: IP 68
12
Physical
• Dimensions (hex × height): 14 × 64 mm (0.55 × 2.52 in.)
• Weight (with cable): 99 g (3.5 oz.)
• Cable length: 2 m (6.56 ft.)
• Mounting: Magnet
• Case material: Stainless steel
• Cable type: Polyurethane
• Sealing: Molded
• Sensing element design: Ceramic, shear
• Connections:
– Molded integral cable (top)
– Fischer type 103 six pin
Optional accessories
CMSS 908-LD magnetic mounting base
CMAC 5220 quick connect mounting base
(used with the SKF Marine Condition
Monitoring kit)
CMAC 5221 quick connect mounting stud (used
with the SKF Marine Condition Monitoring kit)
CMSS 908-LD magnetic mounting base specifications:
• Pull strength: 67 N (15 lb.)
• Outside diameter: 19 mm (0.75 in.)
• Mount: 1/4–28 tapped hole; 1/4–28 mounting stud provided
• Material: Stainless steel
CMAC 5222 labels for measurement locations
(used with the SKF Marine Condition
Monitoring kit)
Orderinginformation
• CMSS2111Small footprint accelerometer with an integrated cable
and a magnetic mount (CMSS 908-LD).
Optionalaccessories
• CMSS908-LDMagnetic mounting base with 1/4–28 stud
• CMAC 5220 Quick connect mounting base with 1/4–28 threaded hole
for sensor mounting (used with the SKF Marine Condition Monitoring
kit)
• CMAC 5221 Quick connect mounting stud with 1/4–28 threaded hole
for machine mounting (qty. 50) (used with the SKF Marine Condition
Monitoring kit)
• CMAC 5222 Labels for measurement locations (qty. 100)
(used with the SKF Marine Condition Monitoring kit)
13
CMSS 2114-K
•
High frequency accelerometer kit
CMXA 45
CMXA 45/75-Z2
•
The CMSS 2114-K is a high frequency accelerometer kit that
includes a high frequency cable with an adhesive mounting base.
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
Specifications
Dynamic
• Sensitivity (±15%): 10 mVg
• Measurement range: ±500 g peak
• Frequency range (±3 dB): 5 to 60 000 Hz
• Non-linearity: ≤ 1%
• Resonance frequency: ≥ 95 kHz
• Transverse sensitivity: ≤ 5%
Electrical
• Power supply:
– Voltage source: 18 to 30 V DC
– Constant current diode: 2 to 20 mA
• Electrical noise:
– Broadband:
· 1 Hz to 10 kHz: 0,002 g RMS
– Spectral:
· 10 Hz: 160 µg/√Hz
· 100 Hz: 40 µg/√Hz
· 1 kHz: 15 µg/√Hz
· 10 kHz: 10 µg/√Hz
• Output impedance: ≤ 100 Ω
• Bias output voltage: 8 to 12 V DC
• Discharge time constant: 0,02 to 0,06 s
352A60 high frequency constant current
accelerometer
Environmental
• Temperature range: –55 to +120 °C (–65 to +250 °F)
• Shock limit: 5 000 g peak
• Base strain sensitivity: ≤ 0,05 g µ
Physical
CMAC 5062 high frequency accelerometer cable
• Dimensions: See drawing
• Weight: 6 g (0.2 oz.)
• Mounting thread: 10-32, male
• Mounting torque: 1,13 to 2,25 Nm (10 to 20 in. lbs.)
• Case material: Stainless steel
• Sealing: Welded hermetic
• Sensing element design: Ceramic, shear
• Connections: 5-44 coaxial (top)
Note: All specifications are at room temperature unless otherwise specified.
14
Adhesive mounting
base
CMXA 70/44
CMXA 75
CMXA 80
• 352A60: High frequency constant current accelerometer
• CMAC 5062: High frequency accelerometer cable, Fischer type
103 six pin to a 5-44 Microdot connector
• Adhesive mounting base
Dimensions
2,8 mm
(0.11 in.)
Note: Loctite 454 insensitive adhesive gel is the recommended adhesive.
This item is not included in the kit.
5-44 coaxial connector
20,6 mm
(0.81 in.)
352A60
4,6 mm (0.18 in.)
10-32 mounting
hole1) 2)
3,3 mm
(0.13 in.)
1)
2)
9,5 mm
(0.38 in.)
Stud removed for
sensor with adhesive
mount option.
M6 × 0,75 thread for
Metric option
10,7 mm
(0.42 in.)
Orderinginformation
• CMSS2114-KHigh frequency accelerometer kit, which includes a
high frequency constant current accelerometer, cable and adhesive
mounting base.
15
CMSS 2200 / CMSS 2200-M8
•
General purpose, low profile, side exit
industrial accelerometer
CMXA 45/75-Z2
•
The CMSS 2200 and CMSS 2200-M8
industrial accelerometers, with their side
exit and two pin connector, offer a low profile for machinery with limited clearance.
The sensor mounts in any orientation.
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
Features
• Rugged, economical and all around
general purpose sensor
• 100 mV/g sensitivity to optimize use in
multiple applications
• Exceptional bias voltage (BV) stability at elevated temperatures
• Designed for exceptional low noise level over a wide temperature
range
• Meets stringent CE, EMC requirements
• Low profile with captive mounting bolts (1/4–28, M6 × 1,00 or
M8 × 1,25) provided
• Corrosion resistant and hermetically sealed
• Reverse polarity wiring protection
CMXA 45
CMXA 70/44
CMXA 75
CMXA 80
Electrical
Specifications
• Power requirements:
– Voltage source: 18 to 30 V DC
– Constant current diode: 2 to 10 mA, recommended 4 mA
• Electrical noise: 2,0 Hz; 20 µg/√Hz
• Output impedance: < 100 Ω
• Bias output voltage: 12 V DC
• Grounding: Case isolated, internally shielded
Dynamic
Environmental
• Sensitivity: 100 mVg
• Sensitivity precision: ±10% at 25 °C (75 °F)
• Measurement range: 80 g peak
• Frequency range:
– ±10%: 1,0 to 5 000 Hz
– ±3 dB: 0,7 to 10 000 Hz
• Amplitude linearity: 1%
• Resonance frequency, mounted, minimum 22 kHz
• Transverse sensitivity: ≤ 5% of axial
• Temperature range: –50 to +120 °C (–60 to +250 °F)
• Vibration limit: 500 g peak
• Shock limit: 5 000 g peak
• Base strain sensitivity: 200 µg/µstrain
• Electromagnetic sensitivity, equivalent g, maximum: 70 µg/gauss
• CE: According to the generic immunity standard for Industrial
Environment EN50082-2
– Acceptance criteria: The generated “false equivalent g level”
under the above test conditions should be less than 2 mg
measured peak to peak
16
Physical
• Dimensions: See drawing
• Weight: 145 g (5.1 oz.)
• Mounting: See ordering information
• Mounting torque: 3,4 Nm (30 in. lbs.)
• Case material: 316L stainless steel
• Sealing: Hermetic
• Connections:
– Pin A: Signal/Power
– Pin B: Common
– Mating connector: CMSS 932-68LC or CMSS 932-68TL, two
pin, IP 68, locking collar or twist lock
• Recommended cable: Two conductor, shielded, fluorine based
polymer jacket, 100 pF/m (30 pF/ft.)
– CMAC 5209, CMAC 5209-06S or CMAC 5209-10
• Recommended magnetic base: CMSS 908-MD
Note: Specifications conform to ISA-RP-37.2 (1 to 64) and are typical values
referenced at 25 °C (75 °F), 24 V DC supply, 4 mA constant current and
100 Hz.
Dimensions
1/4 in. socket head
captive screw
26,0 mm
40,0 mm (1.04 in.)
(1.60 in.)
6,3 mm
(0.25 in.)
MODEL CMSS2200
MODEL CMSS2200-M8
S/N S0000
23,0 mm
(0.92 in.)
CMSS2200:
1/4-28 mounting
thread
CMSS2200-M8:
M8 mounting
thread
25,0 mm
(1.00 in.)
37,0 mm
(1.44 in.)
53,0 mm
(2.10 in.)
Note: This accelerometer is not recommended for use in hazardous
environments.
Two pin connector
MIL-C-5015
Orderinginformation
• CMSS2200General purpose, low profile, side exit industrial
accelerometer with MIL-C-5015 two pin connector. 1/4–28 and M6
mounting studs provided. Calibration sensitivity and nominal
sensitivity are provided for each accelerometer package.
• CMSS2200-M8General purpose, low profile, side exit industrial
accelerometer with MIL-C-5015 two pin connector. M8 mounting
studs provided. Calibration sensitivity and nominal sensitivity are
provided for each accelerometer package.
Optionalaccessories
• CMSS908-MD Medium duty magnetic base
17
CMSS 2210
Intrinsically safe (IS) industrial accelerometer
CMXA 45
•
CMXA 45/75-Z2
CMXA 48
The CMSS 2210 industrial accelerometer is intrinsically safe and is
ATEX and IECEx Group I and II approved.
Specifications
•
•
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
CMXA 75
Dynamic
• Sensitivity (±10%): 100 mVg nominal at 80 Hz
• Frequency range: 2 Hz to 10 kHz ±5% (–3 dB at 0,8 Hz)
• Resonance frequency, mounted, nominal: 18 kHz
• Transverse sensitivity: < 5%
Electrical
• Constant current diode: 0,5 to 8 mA
• Electrical noise: 0,1 mg maximum
• Bias output voltage: 12 V DC, nominal
Environmental
• Temperature range:
– T4: –55 to +115 °C (–65 to +240 °F)
– T6: –55 to +65 °C (–65 to +150 °F)
Physical
• Dimensions: See drawing
• Weight: 100 g (3.5 oz.)
• Mounting torque: 8 Nm (70.8 in. lbs.)
• Case material: Stainless steel
• Sealing: IP 67
• Isolation: Base isolated
• Connections: MIL-C-5015 style two pin
• Recommended cables:
– For CMXA 51-IS: CMAC 5115
– For ATEX Zone 2 CMXA 45, 48, 75, 80: CMAC 5209
• Recommended magnetic base: CMSS 908-MD
18
CMXA 80
Certifications
• Group I:
– Baseefa02ATEX0245X and IECEx BAS 08.0013X
– Ex I M1 Ex ia I: Ta = –55 to +115 °C (–65 to +240 °F)
• Group II*:
– BAS02ATEX1057X and IECEx BAS 08.0013X
– Ex II 1GD T135 °C (275 °F) Ex ia IIC T4
– Ex iaD 20 T135 °C (275 °F): Ta = –55 to +115 °C
(–65 to +240 °F)
– Ex II 1GD T85 °C (185 °F) Ex ia IIC T6
– Ex iaD 20 T85 °C (185 °F): Ta = –55 to +65 °C (–65 to +150 °F)
• 500 V isolation: Units will pass a 500 V isolation test
• Barrier: 1 × MTL7728+ (BAS01ATEX7217) or
(P&F Z728 BAS01ATEX7005) or any other barrier that conforms
to note 5 of ATX027
Dimensions
Two pin connector
MIL-C-5015
51,0 mm
(2.00 in.)
MODEL CMSS2210
S/N S00000
22,2 mm
(0.87 in.)
*Warning: The Ci and Li were previously lower. The installer must take
account of the increase in internal capacitance and inductance present on
this apparatus.
1/4-28
mounting hole
25,0 mm
(1.00 in.)
22,2 mm
(0.87 in.)
25,0 mm
(1.00 in.)
Orderinginformation
• CMSS2210Intrinsically safe (IS) industrial accelerometer.
Optionalaccessories
• CMSS908-MD Medium duty magnetic base
19
CMSS 732A
•
Small diameter accelerometer
CMXA 45
CMXA 45/75-Z2
•
The CMSS 732A is an accelerometer with a 10 × 32 mounting stud.
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
Features
•
•
•
• Wide dynamic range
• Compact construction to fit in tight spaces
• Wide frequency range
• Small size, lightweight
• Hermetic seal
• Designed for stud mounting
• Optional magnetic base mounting
CMXA 70/44
CMXA 75
CMXA 80
Specifications
Dynamic
• Sensitivity: 10 mV/g
• Sensitivity precision: ±5% at 25 °C (75 °F)
• Measurement range: 500 g peak
• Frequency range:
– ±5%: 2,0 to 15 000 Hz
– ±3 dB: 0,5 to 25 000 Hz
• Amplitude non–linearity: 1%
• Resonance frequency: 60 kHz
• Transverse sensitivity: 5% of axial
• Temperature response:
– –50 °C (–60 °F): –5%
– +120 °C (+250 °F): +5%
Electrical
• Power requirements:
– Voltage source: 18 to 30 V DC
– Constant current diode: 2 to 10 mA
• Electrical noise:
– Broadband:
· 2,5 Hz to 25 kHz: 200 µg
– Spectral:
· 10 Hz: 20 µg/√Hz
· 100 Hz: 3 µg/√Hz
· 1 000 Hz: 2 µg/√Hz
· 10 000 Hz: 2 µg/√Hz
• Output impedance: ≤ 100 Ω
• Bias output voltage: 10 V DC
• Grounding: Case isolated, internally shielded
20
Environmental
• Temperature range: –50 to +120 °C (–60 to +250 °F)
• Vibration limit: 500 g peak
• Shock limit: 5 000 g peak
• Base strain sensitivity: 0,005 g/µ strain
• Electromagnetic sensitivity, equivalent g: 100 µg/gauss
Physical
• Dimensions: See drawing
• Weight: 13 g (0.5 oz.)
• Mounting: 10 × 32 tapped hole
• Case material: 316L stainless steel
• Connections:
– Shell: Common
– Pin A: Power/Signal
– Output connector: 10 × 32 coaxial
– Mating connector: R1
• Recommended cable: CMAC 5061
• Recommended magnetic base: CMSS B13
Optional accessories
Dimensions
12,2 mm
(0.48 in.)
MODEL CMSS732A
CMSS B13 magnetic mounting base
23,6 mm
(0.93 in.)
S/N 00000
1/2 in. hex
CMSS B13 magnetic mounting base specifications:
10-32
coaxial
connector
• Description: Rare earth, two-pole magnet
• Pull strength: 16 kg (35 lb.)
• Outside diameter: 25 mm (1.0 in.)
• Mount: 1/4–28 tapped hole (Metric studs available)
• Knurled gripping edge
12,4 mm
(0.49 in.)
10-32
mounting hole
Orderinginformation
• CMSS732ASmall diameter, high frequency accelerometer. A 10 × 32
mounting stud is provided. Calibration sensitivity is provided on each
accelerometer package with nominal sensitivity etched on each unit.
Optionalaccessories
• CMSSB13Magnetic base mounting
• CMAC5061 High frequency accelerometer cable
21
CMSS 793-CA
•
CSA approved, general purpose industrial
accelerometer
CMXA 45
CMXA 45/75-Z2
•
The CMSS 793-CA is an industrial standard acceleration sensor with
a top exit, two pin connector and agency approvals.
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
Features
• Class I, Division 1 certification
• Ground isolated
• Rugged construction
• Corrosion resistant and hermetically sealed for installation in high
humidity areas
• ESD protection
• Reverse wiring protection
CMXA 70/44
CMXA 75
CMXA 80
Specifications
Dynamic
• Sensitivity, ±5%, 25 °C (75 °F): 100 mVg
• Measurement range: 80 g peak
• Frequency range:
– ±5%: 1,5 to 5 000 Hz
– ±10%: 1,0 to 7 000 Hz
– ±3 dB: 0,5 to 15 000 Hz
• Amplitude non-linearity: 1%
• Resonance frequency: 25 kHz
• Transverse sensitivity: ≤ 5% of axial
• Temperature response:
– –50 °C (–60 °F): –10%
– +120 °C (+250 °F): +5%
Electrical
• Power requirements:
– Voltage source: 18 to 30 V DC
– Constant current diode: 2 to 10 mA
• Electrical noise:
– Broadband:
· 2,5 Hz to 25 kHz: 600 µg
– Spectral:
· 10 Hz: 8 µg/√Hz
· 100 Hz: 5 µg/√Hz
· 1 000 Hz: 5 µg/√Hz
• Output impedance: ≤ 100 Ω
• Bias output voltage: 12 V DC
• Grounding: Case isolated, internally shielded
22
Environmental
• Temperature range: –50 to +120 °C (–60 to +250 °F)
• Vibration limit: 500 g peak
• Shock limit: 5 000 g peak
• Base strain sensitivity: 0,0005 g/µ strain
Agency approvals
• Canadian Standards Association (CSA)
– Class I, Division 1, Groups A, B, C, D
– Class II, Division 1, Groups E, F, G
– Class III, Division 1
Physical
• Dimensions: See drawing
• Weight: 112 g (4.0 oz.)
• Mounting: 1/4–28 tapped hole
• Case material: 316L stainless steel
• Sealing: Hermetic
• Sensing element design: PZT ceramic / compression
• Connections:
– Shell: Ground
– Pin A: Power/Signal
– Pin B: Common
– Output connector: MIL-C-5015 style two pin
– Mating connector: R6 type
• Recommended cable: CMAC 5209, CMAC 5209-06S or
CMAC 5209-10
• Recommended magnetic base: CMSS 908-MD
Dimensions
Two pin connector
MIL-C-5015
15/16 in. hex
61,0 mm
(2.42 in.)
45,0 mm
(1.78 in.)
MODEL CMSS793-XX
S/N S00000
1/4-28
mounting hole
25,4 mm
(1.00 in.)
25,4 mm
(1.00 in.)
25,4 mm
(1.00 in.)
Orderinginformation
• CMSS793-CACSA approved, general purpose industrial
accelerometer. 1/4–28 mounting studs are provided. Calibration
sensitivity is provided on each accelerometer package with nominal
sensitivity etched on each unit.
Optionalaccessories
• CMSS908-MD Medium duty magnetic base
23
CMSS 793-EE
CMXA 45
ATEX approved, intrinsically safe (IS), general
purpose industrial accelerometer
•
CMXA 45/75-Z2
CMXA 48
•
•
The CMSS 793-EE is an industrial standard acceleration sensor with
a top exit C5015 two pin connector and agency approvals.
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
Features
CMXA 75
• Intrinsically safe certification
• Ground isolated
• Rugged construction
• Corrosion resistant and hermetically sealed for installation in high
humidity areas
• ESD protection
• Reverse wiring protection
CMXA 80
Specifications
Dynamic
• Sensitivity, ±5%, 25 °C (75 °F): 100 mVg
• Measurement range: 80 g peak
• Frequency range:
– ±5%: 1,5 to 5 000 Hz
– ±10%: 1,0 to 7 000 Hz
– ±3 dB: 0,5 to 15 000 Hz
• Amplitude non-linearity: 1%
• Resonance frequency: 25 kHz
• Transverse sensitivity: ≤ 5% of axial
• Temperature response:
– –50 °C (–60 °F): –10%
– +120 °C (+250 °F): +5%
Environmental
• Temperature range: –50 to +120 °C (–60 to +250 °F)
• Vibration limit: 500 g peak
• Shock limit: 5 000 g peak
• Base strain sensitivity: 0,0005 g/µ strain
Agency approvals
• Intrinsically safe –50 to +120 °C (–60 to +250 °F) for:
– ATEX Zone 0
– II 1 G
– Ex ia IIC T4 Ga
Electrical
• Power requirements:
– Voltage source: 18 to 30 V DC
– Constant current diode: 2 to 10 mA
• Electrical noise:
– Broadband:
· 2,5 Hz to 25 kHz: 600 µg
– Spectral:
· 10 Hz: 8 µg/√Hz
· 100 Hz: 5 µg/√Hz
· 1 000 Hz: 5 µg/√Hz
• Output impedance: ≤ 100 Ω
• Bias output voltage: 12 V DC
• Grounding: Case isolated, internally shielded
24
Note: Must be installed per drawing 11535, revision F.
Physical
• Dimensions: See drawing
• Weight: 112 g (4.0 oz.)
• Mounting: 1/4–28 tapped hole
• Case material: 316L stainless steel
• Sealing: Hermetic
• Sensing element design: PZT ceramic / compression
• Connections:
– Shell: Ground
– Pin A: Power/Signal
– Pin B: Common
– Output connector: MIL-C-5015 style two pin
– Mating connector: R6 type
• Recommended cables:
– For CMXA 51-IS: CMAC 5115
– For ATEX Zone 2 CMXA 45, 48, 75, 80: CMAC 5209
• Recommended magnetic base: CMSS 908-MD
Dimensions
Two pin connector
MIL-C-5015
15/16 in. hex
61,0 mm
(2.42 in.)
45,0 mm
(1.78 in.)
MODEL CMSS793-XX
S/N S00000
1/4-28
mounting hole
25,4 mm
(1.00 in.)
25,4 mm
(1.00 in.)
25,4 mm
(1.00 in.)
Orderinginformation
• CMSS793-EEATEX approved, intrinsically safe (IS), general purpose
industrial accelerometer. 1/4–28 mounting studs are provided.
Calibration sensitivity is provided on each accelerometer package with
nominal sensitivity etched on each unit.
Optionalaccessories
• CMSS908-MD Medium duty magnetic base
25
CMSS 908-MD
•
•
•
•
•
•
•
•
Medium duty magnetic base
The CMSS 908-MD is a multi-purpose magnetic base designed for
industrial vibration monitoring applications. The low profile magnet
has a 1/4–28 mounting hole to allow compatibility with SKF accelerometers and provides a solid mechanical connection to the machine.
Specifications
• Diameter: 35 mm (1.38 in.)
• Height: 19 mm (0.75 in.)
• Mounting hole: 1/4–28
• Pull strength: 23 kg (50 lbs.)
CMXA 45
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
CMXA 75
CMXA 80
Accelerometer compatibility
The CMSS 908-MD medium duty magnetic base is compatible with
the following accelerometers:
• CMAC 4370: Triax accelerometer
• CMSS 2200 / CMSS 2200-M8: General purpose, low profile, side
exit industrial accelerometer
• CMSS 2210: Intrinsically safe (IS) industrial accelerometer
• CMSS 793-CA: CSA approved, general purpose industrial
accelerometer
• CMSS 793-EE: ATEX approved, intrinsically safe (IS), general
purpose industrial accelerometer
Dimensions
1/4-28 mounting hole
19,0 mm
(0.75 in.)
35,0 mm (1.40 in.)
Orderinginformation
• CMSS908-MDMedium duty magnetic base.
26
Cables
Cablerecommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Accelerometercables
Triaxialaccelerometercoiledcable,CMAC5009 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Highfrequencyaccelerometerstraightcable,CMAC5061 . . . . . . . . . . . . . . . . . . . 30
Highfrequencyaccelerometerstraightcable,CMAC5062 . . . . . . . . . . . . . . . . . . . 31
Splitter,fourchannelstraightcable,CMAC5079 . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
ATEXcertifiedaccelerometercoiledcable,CMAC5115 . . . . . . . . . . . . . . . . . . . . . . 32
Accelerometercoiledcable,2m(6.56 ft.),CMAC5209 . . . . . . . . . . . . . . . . . . . . . . 32
Accelerometercoiledcablewithsafetybreakaway,CMAC5209-06S . . . . . . . . . . . 33
Accelerometercoiledcable,3m(10 ft.),CMAC5209-10 . . . . . . . . . . . . . . . . . . . . . 33
Tachometercables
BNCtachometerstraightcable,CMAC5211 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Lasertachometerkitstraightcable,24cm(9.5 in.), CMAC5213 . . . . . . . . . . . . . . 34
Lasertachometerkitstraightcable,2m(6.56 ft.),CMAC5214 . . . . . . . . . . . . . . . 35
Extensioncables
CH1signalinput straightextensioncable,5m(16.4 ft.),CMAC5036 . . . . . . . . . . 35
CH1signalinput straightextensioncable,10m(32.8 ft.),CMAC5037 . . . . . . . . . 36
Tachometerstraightextensioncable,5m(16.4 ft.), CMAC5043 . . . . . . . . . . . . . . 36
Tachometerstraightextensioncable,10m(32.8 ft.), CMAC5044 . . . . . . . . . . . . . 37
27
Miscellaneouscables
Cableconverter,twopinMILtoBNC,CMAC3715 . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Signalinputstraightcable,CMAC5023. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Power/Triggersplitterstraightcable,CMAC5032 . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Audioheadphonestraightcable,CMAC5078 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
USB/AtoBstraightcable,CMAC5082 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Temperatureguninterfacestraightcable,CMAC5087 . . . . . . . . . . . . . . . . . . . . . . 40
Signalinputstraightcable,CMAC5088. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
USBcommunication/powersplitterstraightcable,CMAC5095 . . . . . . . . . . . . . . . 41
AC/DCsignalcoiledcable,CMAC5116 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Triggercoiledcable, CMAC5117 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Serialcommunicationcable,CMAC5201. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Strobelightinputstraightcable,CMAC5404 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Strobelightoutputstraightcable,CMAC5406 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Signalinputstraightcable(microphonecable),CMAC5093 . . . . . . . . . . . . . . . . . . 44
Important
SKF Microlog connectors use a locking mechanism for secure connections. To disconnect Fischer cables from the SKF Microlog connectors,
pull on the lower portion of the connector, as illustrated below.
Correct way to
disconnect cables
28
Wrong way to
disconnect cables
Cable recommendations
The following tables shows which cables are recommended for the accelerometers and hardware found in this catalog.
Cablesrecommendedforaccelerometers
CSA approved, general purpose industrial accelerometer
ATEX approved, IS, general purpose industrial accelerometer
•
CMAC5209-10
CMSS 793-CA
CMSS 793-EE
CMAC5209-06S
•
•
Intrinsically safe (IS) industrial accelerometer
Small diameter accelerometer
CMAC5209
•
CMSS 2200
General purpose, low profile, side exit industrial accelerometer
CMSS 2200-M8 General purpose, low profile, side exit industrial accelerometer
CMSS 2210
CMSS 732A
CMAC5115
•
Triax accelerometer kit
High frequency accelerometer kit
CMAC5062
CMAC 4370-K
CMSS 2114-K
CMAC5061
Accelerometer
modelnumber Accelerometerdescription
CMAC5009
Cablemodelnumber
••
••
••
•
•
•
Cablesrecommendedforhardware,etc.
CMSS 6155XK-U-CE Optical phase reference kit
CMSS 6165K-AX
Strobe light kit
CMSS 6195AX-K
Smart laser sensor tachometer
•
•
•
CMAC5406
CMAC5404
• •
• •
•
••
•
CMAC5214
Universal power supply
Audio headset
•
• •
• • • •
••
•
CMAC5213
CMAC 5090
CMAC 5403
CMAC5211
Docking station
Microphone with integral
preamplifier kit
CMAC5095
CMAC 5068
CMAC 5084
CMAC5088
Modal analysis hammer kit
Modal analysis hammer kit
CMAC5087
CMAC 5057
CMAC 5058
CMAC5082
Laser tach. kit, ATEX certified
Modal analysis hammer kit
CMAC5078
CMAC 5030K-Z2
CMAC 5056
CMAC5062
Infrared thermometer
Laser tachometer kit
CMAC5061
CMAC 4200-K-SL
CMAC 5030K
CMAC5044
Productdescription
CMAC5043
Hardware
modelnumber
CMAC5023
Cablemodelnumber
•
•
•
• •
29
CMAC 5009
Triaxial accelerometer coiled
cable
The CMAC 5009 coiled cable connects to the
SKF Microlog CH1 input connector at one
end and to a triaxial accelerometer at the
other end. The cable is recommended for
use with the CMAC 4370-K triax accelerometer kit.
Specifications
• Connectors: Fischer type 103 six pin CH1
I/P to a four pin socket
• Length: 2 m (6.56 ft.) coiled
•
CMAC 5061
CMXA 45
CMXA 45/75-Z2
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
High frequency accelerometer
straight cable
CMXA 70/44
CMXA 75
CMXA 80
The CMAC 5061 accelerometer cable is used
with the CMSS 732A accelerometer and
with the CMAC 5056 modal analysis hammer kit.
Specifications
• Connectors: Fischer type 103 six pin to a
10-32 Microdot connector
• Length: 1,5 m (5 ft.) straight
•
CMXA 45
CMXA 45/75-Z2
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
Orderinginformation
Orderinginformation
• CMAC5009Triaxial accelerometer coiled cable.
• CMAC5061High frequency accelerometer straight cable.
30
CMAC 5062
High frequency accelerometer
straight cable
The CMAC 5062 high frequency accelerometer cable is used with the 352A60 high frequency accelerometer in the CMSS 2114-K
kit and in the CMAC 5057 modal analysis
hammer kit.
Specifications
• Connectors: Fischer type 103 six pin to a
Microdot
• Length: 3 m (10 ft.) straight
•
CMAC 5079
CMXA 45
CMXA 45/75-Z2
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
Splitter, four channel straight
cable
CMXA 70/44
CMXA 75
The CMAC 5079 cable is used for connecting
to either CH1 or CH2 on the CMXA 80 and
CMXA 48. If connected to CH1, lead A gives
channel 1 and lead B gives channel 4. If connected to CH2, lead A gives channel 2 and
lead B gives channel 3.
CMXA 80
Specifications
CMXA 45
CMXA 45/75-Z2
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
CMXA 75
•
CMXA 80
• Connectors: Two Fischer type 103 six pin
female sockets to one Fischer type 103 six pin male
• Length: 45 cm (1.5 ft.) straight
Note: Two cables are required to collect four channel measurements
Note: For CMXA 45 and CMXA 75, this cable can be used in CH2 only to
give three single axis simultaneous accelerometer inputs. A single accelerometer is connected to CH1 giving channel 1, then the cable into CH2 giving the same inputs as for CH2 of the CMXA 80.
Orderinginformation
Orderinginformation
• CMAC5062High frequency accelerometer straight cable.
• CMAC5079Splitter, four channel straight cable.
31
CMAC 5115
CMAC 5209
CMXA 45
ATEX certified accelerometer
coiled cable
CMXA 45/75-Z2
Accelerometer coiled cable,
2 m (6.56 ft.)
CMXA 48
The CMAC 5115 cable is ATEX certified and
is used to connect the accelerometer to the
signal connector.
CMXA 48/80-Z2
•
CMXA 51-IS
CMXA 70/44
Specifications
• Connectors: Fischer type 102 four pin to
two pin MIL
• Length: 2 m (6.56 ft.) coiled
The CMAC 5209 coiled cable connects to the
CH1 or CH2 input connector at one end and
to an accelerometer at the other end. The
accelerometer connection is a two pin MIL
connector.
CMXA 75
CMXA 80
Specifications
• Connectors: Fischer type 103 six pin to
two pin MIL
• Length: 2 m (6.56 ft.) coiled
•
•
•
•
CMXA 45
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
Orderinginformation
Orderinginformation
• CMAC5115ATEX certified accelerometer coiled cable.
• CMAC5209Accelerometer coiled cable, 2 m (6.56 ft.).
32
CMAC 5209-06S
Accelerometer coiled cable
with safety breakaway
The CMAC 5209-06S coiled accelerometer
cable is similar to the CMAC 5209 cable, but
also includes a safety breakaway.
Specifications
• Connectors: Fischer type 103 six pin to
two pin MIL
• Length: 2 m (6.56 ft.) coiled
•
•
•
•
CMAC 5209-10
CMXA 45
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
Accelerometer coiled cable,
3 m (10 ft.)
The CMAC 5209-10 coiled cable connects to
the CH1 or CH2 input connector at one end
and to an accelerometer at the other end.
CMXA 70/44
CMXA 75
CMXA 80
Specifications
• Connectors: Fischer type 103 six pin to
two pin MIL
• Length: 3 m (10 ft.) coiled
•
•
•
•
CMXA 45
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
Orderinginformation
Orderinginformation
• CMAC5209-06SAccelerometer coiled cable with safety breakaway.
• CMAC5209-10Accelerometer coiled cable, 3 m (10 ft.).
33
CMAC 5211
BNC tachometer straight
cable
The CMAC 5211 cable connects to the power connector at one end (using the power
connector’s tachometer input pin) and to any
male BNC connector on the other end. It can
be used with any tachometer signal source
that does not require the SKF Microlog to
power it.
•
CMAC 5213
CMXA 45
CMXA 45/75-Z2
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
Laser tachometer kit straight
cable, 24 cm (9.5 in.)
CMXA 70/44
CMXA 75
CMXA 80
Note: The CMSS 6195 Laser Reference Kit (CMVA
version kit) or CMSS 6155 Optical Phase
Reference Kit (CMVA 60 version kit) requires a
CMAC 5211 BNC tachometer cable to work with the SKF Microlog.
Specifications
• Connectors: Fischer type 103 seven pin trigger I/P to BNC
• Length: 1 m (3.28 ft.) straight
The CMAC 5213 laser tachometer cable
connects the tachometer to the SKF
Microlog.
The CMAC 5213 cable is a shorter cable
than is sold in the CMAC 5030K laser
tachometer kit. This cable is only 24 cm
(9.5 in.) long. This shorter cable is preferred
if the user uses the CMAC 5030K kit’s
mounting bracket to attach the tachometer
directly to the SKF Microlog.
•
•
•
•
CMXA 45
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
Specifications
• Connectors: Fischer type 103 seven pin to four pin socket
• Length: 24 cm (9.5 in.) straight
Orderinginformation
Orderinginformation
• CMAC5211BNC tachometer straight cable.
• CMAC5213Laser tachometer kit straight cable, 24 cm (9.5 in.).
34
CMAC 5214
Laser tachometer kit straight
cable, 2 m (6.56 ft.) for
CMAC 5030K
The CMAC 5214 laser tachometer cable
connects the tachometer to the SKF
Microlog.
The CMAC 5214 cable, which is also
included in the CMAC 5030K and
CMAC 5030K-Z2 laser tachometer kits,
allows the user to place the tachometer on a
stationary surface up to 2 m (6.56 ft.) away
from the SKF Microlog.
•
•
•
•
CMAC 5036
CMXA 45
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CH1 signal input straight extension cable, 5 m (16.4 ft.)
CMXA 70/44
The CMAC 5036 cable, which is used for the
CH1 signal input, is a straight extension
cable that is 5 m (16.4 ft.) long. This cable
can be used with single channel and triax
sensors.
CMXA 75
CMXA 80
Specifications
• Connectors: Fischer type 103 six pin
female to Fischer type 103 six pin male
• Length: 5 m (16.4 ft.) straight
•
CMXA 45
CMXA 45/75-Z2
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
Specifications
• Connectors: Fischer type 103 seven pin to four pin socket
• Length: 2 m (6.56 ft.) straight
Orderinginformation
Orderinginformation
• CMAC5214Laser tachometer kit straight cable, 2 m (6.56 ft.).
• CMAC5036CH1 signal input straight extension cable, 5 m (16.4 ft.).
35
CMAC 5037
CH1 signal input straight extension cable, 10 m (32.8 ft.)
The CMAC 5037 cable, which is used for the
CH1 signal input, is a straight extension
cable that is 10 m (32.8 ft.) long. This cable
can be used with single channel and triax
sensors.
Specifications
• Connectors: Fischer type 103 six pin
female to Fischer type 103 six pin male
• Length: 10 m (32.8 ft.) straight
•
CMAC 5043
CMXA 45
CMXA 45/75-Z2
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
Tachometer straight extension cable, 5 m (16.4 ft.)
CMXA 70/44
The CMAC 5043 straight extension cable is
for use with the CMAC 5030K and
CMAC 5030K-Z2 laser tachometer kits. This
cable is 5 m (16.4 ft.) long and can be used
in conjunction with the CMAC 5211 cable.
CMXA 75
CMXA 80
Specifications
• Connectors: Fischer type 103 seven pin
female to Fischer type 103 seven pin
male
• Length: 5 m (16.4 ft.) straight
•
•
•
•
CMXA 45
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
Orderinginformation
Orderinginformation
• CMAC5037CH1 signal input straight extension cable, 10 m .
• CMAC5043Tachometer straight extension cable, 5 m (16.4 ft.).
36
CMAC 5044
Tachometer straight extension cable, 10 m (32.8 ft.)
The CMAC 5044 straight extension cable is
for use with the CMAC 5030K and
CMAC 5030K-Z2 laser tachometer kits. This
cable is 10 m (32.8 ft.) long and can be used
in conjunction with the CMAC 5211 cable.
Specifications
• Connectors: Fischer type 103 seven pin
female to Fischer type 103 seven pin
male
• Length: 10 m (32.8 ft.) straight
•
•
•
•
CMAC 3715
CMXA 45
CMXA 45/75-Z2
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 45
Cable converter, two pin MIL
to BNC
CMXA 70/44
CMXA 75
CMXA 80
CMXA 48
The CMAC 3715 adapter, when combined
with the CMAC 5209 accelerometer cable,
allows the SKF Microlog to connect to any
male BNC connector. This is useful for
reading buffered outputs from protection
systems, switch boxes or process signal
sources.
The adapter does not block DC signals, so
the user must be careful to avoid applying
power to a buffered signal output.
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
Specifications
• Connectors: Two pin MIL to BNC
• Length: 8,5 cm (3.35 in.)
Orderinginformation
Orderinginformation
• CMAC5044Tachometer straight extension cable, 10 m (32.8 ft.).
• CMAC3715Cable converter, two pin MIL to BNC.
37
CMAC 5023
Signal input straight cable
•
CMAC 5032
CMXA 45
CMXA 45/75-Z2
The CMAC 5023 cable connects to the SKF
Microlog CH1 or CH2 signal input connector
at one end (using the input connector’sCH1
input pin) and to any male BNC connector at
the other end. This lightweight cable is also
used in the CMAC 5056, CMAC 5057 and
CMAC 5058 modal analysis hammer kits.
Note: Refer to CMAC 5088 for a heavy duty
version of this cable.
•
CMXA 51-IS
CMXA 70/44
CMXA 75
CMXA 80
Specifications
CMXA 45
CMXA 45/75-Z2
CMXA 48
The CMAC 5032 cable allows the connection
of the tachometer, instrument power and
USB communications (via the CMAC 5095
cable) simultaneously.
Specifications
• Connectors: One Fischer type 103 seven
pin plug to two Fischer type 103 seven
pin sockets
• Length: 30 cm (11.8 in.)
• Cable: Eight-core 24 AWG screened cable
• Connectors: Fischer type 103 six pin CH1 I/P to BNC
• Length: 1 m (3 ft.) straight
Orderinginformation
Orderinginformation
• CMAC5023Signal input straight cable.
• CMAC5032Power/Trigger splitter straight cable.
38
•
CMXA 48
CMXA 48/80-Z2
•
•
•
Power/Trigger splitter
straight cable
CMXA 48/80-Z2
CMXA 51-IS
•
•
CMXA 70/44
CMXA 75
CMXA 80
CMAC 5078
Audio headphone straight
cable
The CMAC 5078 cable connects the
CMAC 5403 headphones to the SKF Microlog.
•
CMAC 5082
CMXA 45
CMXA 45
USB / A to B straight cable
CMXA 45/75-Z2
•
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
The CMAC 5082 USB cable is used to connect the CMAC 5068 docking station to the
PC.
•
•
• Connectors: Fischer type 103 seven pin to
female audio
• Length: 20 cm (7.9 in.) straight
•
•
CMXA 75
CMXA 80
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
CMXA 70/44
Specifications
CMXA 48
Specifications
• Connectors: USB Type A to USB Type B
• Length: 2 m (6.56 ft.) straight
Orderinginformation
Orderinginformation
• CMAC5078Audio headphone straight cable.
• CMAC5082USB / A to B straight cable.
CMXA 75
•
CMXA 80
39
CMAC 5087
Temperature gun interface
straight cable
The CMAC 5087 cable is used to connect the
CMAC 4200-K-SL infrared thermometer to
the SKF Microlog.
Specifications
• Connectors: Fischer type 103 six pin to
input adapter
• Length: 1,5 m (4.9 ft.) straight
•
CMAC 5088
CMXA 45
Signal input straight cable
CMXA 45/75-Z2
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
CMXA 45
CMXA 45/75-Z2
The CMAC 5088 cable is a heavy duty version of the CMAC 5023 cable. The
CMAC 5088 cable connects to the SKF
Microlog CH1 or CH2 signal input connector
at one end (using the input connector’s CH1
input pin) and to any male BNC connector at
the other end.
Note: Refer to CMAC 5023 for a lightweight
version of this cable.
Specifications
• Connectors: Fischer type 103 six pin CH1
I/P to BNC
• Length: 2 m (6.56 ft.) straight
Orderinginformation
Orderinginformation
• CMAC5087Temperature gun interface straight cable.
• CMAC5088Signal input straight cable.
40
•
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
•
•
CMXA 75
CMXA 80
CMAC 5095
USB communication/power
splitter straight cable
The CMAC 5095 four-core shielded USB
cable has a standard USB Type A plug. The
cable is used for USB communications and
power without the docking station.
The USB Type A plug is used to connect to
the PC, while the in-line DC jack socket connects to the CMAC 5090 universal power
supply and the Fischer plug connects to the
SKF Microlog,
•
•
•
•
CMAC 5116
CMXA 45
CMXA 45/75-Z2
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 45
AC/DC signal coiled cable
CMXA 70/44
CMXA 48
The CMAC 5116 cable is offered as an
optional accessory. It is not part of the
CMXA 51-IS ATEX certification; therefore, it
must be approved by the site’s safety officer
before use in a hazardous area.
•
CMXA 51-IS
CMXA 70/44
CMXA 75
CMXA 75
CMXA 80
CMXA 48/80-Z2
Specifications
CMXA 80
• Connectors: Fischer four pin to BNC
• Length: 2 m (6.56 ft.) coiled
Specifications
• Connectors: USB Type A and a standard 2,1 mm (0.083 in.)
in-line DC jack socket to Fischer SE103A057-130 plug
• Length: 2 m (6.56 ft.) straight
Orderinginformation
Orderinginformation
• CMAC5095USB communication/power splitter straight cable.
• CMAC5116AC/DC signal coiled cable.
41
CMAC 5117
CMAC 5201
CMXA 45
Trigger coiled cable
CMXA 45
Serial communication cable
CMXA 45/75-Z2
CMXA 45/75-Z2
CMXA 48
The CMAC 5117 cable is offered as an
optional accessory. It is not part of the
CMXA 51-IS ATEX certification; therefore, it
must be approved by the site’s safety officer
before use in a hazardous area.
CMXA 48/80-Z2
•
CMXA 51-IS
CMXA 70/44
CMXA 75
Specifications
• Connectors: Fischer three pin to BNC
• Length: 2 m (6.56 ft.) coiled
CMXA 80
CMXA 48
The CMAC 5201 cable has nine pins (female
at both ends) that all connect straight
through. It is required for uploading/downloading data between the host computer and
the SKF Microlog.
For uploading to laptop computers with a
USB connection, there is no USB to Serial
cable available from SKF; however, an aftermarket USB adapter may be purchased at
most electronics stores or via the web.
CMXA 48/80-Z2
•
Specifications
• Connectors: Nine pin female to nine pine female
• Length: 2 m (6.56 ft.)
Orderinginformation
Orderinginformation
• CMAC5117Trigger coiled cable.
• CMAC5201Serial communication cable.
42
CMXA 51-IS
CMXA 70/44
CMXA 75
CMXA 80
CMAC 5404
Strobe light input straight
cable
The CMAC 5404 cable is used for input to
the CMSS 6165 strobe light from the
SKF Microlog.
Specifications
• Connectors: Fischer type 102 seven pin to
input adapter
• Length: 2 m (6.56 ft.) straight
•
CMAC 5406
CMXA 45
CMXA 45/75-Z2
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
Strobe light output straight
cable
The CMAC 5406 cable is used for output
from the CMSS 6165 strobe light to the
SKF Microlog.
CMXA 70/44
CMXA 75
CMXA 80
Specifications
• Connectors: Fischer type 103 seven pin to
output adapter
• Length: 2 m (6.56 ft.) straight
Orderinginformation
Orderinginformation
• CMAC5404Strobe light input straight cable.
• CMAC5406Strobe light output straight cable.
•
CMXA 45
CMXA 45/75-Z2
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
43
CMAC 5093
Signal input straight cable
(microphone cable)
The CMAC 5093 cable has a BNC connector
on one end to connect to the CMAC 5091
microphone and a Fischer connector on the
other end to connect to the SKF Microlog.
This cable is used in the SKF Microlog
Idler Sound Monitor kits.
Specifications
•
CMXA 45
CMXA 45/75-Z2
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
•
•
CMXA 75
CMXA 80
• Connectors: Fischer type 103 six pin to
BNC
• Length: 51 cm (20 in.) coiled
Orderinginformation
• CMAC5093 Signal input straight cable (microphone cable).
44
Hardware
Infraredthermometer,CMAC4200-K-SL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Lasertachometerkit,CMAC5030K . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Lasertachometerkit–ATEXcertified,CMAC5030K-Z2 . . . . . . . . . . . . . . . . . . . . . 49
Modalanalysishammerkit,CMAC5056/CMAC5057/CMAC5058 . . . . . . . . . . . . 50
Modalanalysishammerkit,CMAC5059 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Microphonewithintegralpreamplifierkit,CMAC5084 . . . . . . . . . . . . . . . . . . . . . . 56
AC/DCcurrentclamp,CMAC5208. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
SKFMicrologAnalyzerfieldbalancingaccessorykit,
CMCP850-01/CMCP850-02/CMCP850-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Opticalphasereferencekit,CMSS6155XK-U-CE . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Opticalphasereferencemagneticholder,CMSS6156 . . . . . . . . . . . . . . . . . . . . . . . 63
Strobelightkit,CMSS6165K-AX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Smartlasersensortachometer,CMSS6195AX-K . . . . . . . . . . . . . . . . . . . . . . . . . . 67
45
CMAC 4200-K-SL
•
Infrared thermometer
CMXA 45
CMXA 45/75-Z2
•
The SKF CMAC 4200-K-SL infrared thermometer
with laser sighting is a rugged, easy to use, portable,
non-contact thermometer. Ideal for a broad range of
maintenance tasks, the CMAC 4200-K-SL may be
connected directly to the SKF Microlog series analyzers for quick, accurate recording of surface temperatures. It is one of a variety of accessories offered by
SKF to work with the SKF Microlog in enhancing the
overall effectiveness of a predictive maintenance program.
The CMAC 4200-K-SL measures the amount of infrared energy
emitted by an object and converts it to a display of the object’s surface temperature. The handheld, infrared thermometer takes noncontact temperature measurement technology to a new level.
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
Features
• Designed for physically challenging environments
• Easy to use
• Adjustable emissivity with on-board table
• Fast response time
• Accuracy ±1% of reading
• Wide temperature range
Specifications
Graphic display
View more information at a glance. The CMAC 4200-K-SL infrared
thermometer automatically creates a graphic display of the last 10
temperature points measured using the maximum and minimum
temperature values to establish the range.
Graphic display
Alarm light
Laser
indicator
Bar graph display
Battery
indicator
46
Emissivity
• Temperature range: –30 to +900 °C (–25 to +1 600 °F)
• Display resolution: 0,1 °C (0.2 °F)
• Accuracy:
– ±1% of reading, or ±1 °C (±2 °F), whichever is greater at
23 °C (73 °F)
– ±2 °C (±4 °F) for targets below 0 °C (32 °F)
• Repeatability: ±0,5% of reading, or ±1 °C (±2 °F)
• Response time (95%): 250 ms
• Spectral response: 8 to 14 µm
• Optical resolution: 60:1
• Ambient operating range: 0 to 50 °C (30 to 120 °F); Laser
maximum 45 °C (115 °F)
• Relative humidity: 10 to 95%, non-condensing at up to
30 °C (85 °F)
• Storage temperature: –20 to +50 °C (–5 to +120 °F) without
battery
• Analog output: 1 mV/°C (mV/°F)
• Power: Two 1,5 volt AA alkaline batteries
• Tripod mount: 1/4-20 UNC
• Dimensions: 200 × 170 × 50 mm (7.9 × 6.7 × 2.0 in.)
• Weight: 480 g (22 oz.)
Kit contents
• CMAC 4200: Infrared thermometer
• 31784200 Nylon belt holster
• 31678902 Hard carrying case
• Operator’s guide
CMAC 4200 infrared thermometer
31678902 carrying case
Requiredasseparatepurchase:
• CMAC 5087 temperature gun interface
cable
CMAC 5087
temperature gun
interface cable
31784200 nylon belt holster
Orderinginformation
• CMAC4200-K-SLInfrared thermometer with adapter, operator’s
guide, nylon holster and hard carrying case.
Optionalaccessories
• 31784200 Nylon belt holster for infrared thermometer
• 31678902 Hard plastic carrying case
• CMAC5087Temperature gun interface cable
47
CMAC 5030K
•
Laser tachometer kit
CMXA 45
CMXA 45/75-Z2
•
The CMAC 5030K laser tachometer kit contains a small tachometer for easy mounting.
Along with the tachometer, this kit includes
a bracket for mounting the tachometer
directly to the SKF Microlog using the camera mount located on the bottom of the SKF
Microlog. The kit also includes a two-meter
cable to connect the tachometer to the SKF
Microlog and a small tripod for a stationary
mounting of the tachometer during the
measurement. The key features of this laser
tachometer kit include:
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
• Operating frequency up to 250 000 r/min
• Long optical range, up to 2 m (6.56 ft.)
• Wide angle of operation, up to 80°
• On target indicator standard
• Protection rating: IP 67
Specifications
• Material: Stainless steel body
• Color: Silver
• Laser type: Class 2
• Optical range: 100 to 2 000 mm (0.33 to 6.56 ft.)
• Power: 1 mW maximum
• Current consumption: 45 mA maximum
• Cable: Fischer seven pin type 103 to four pin socket, 2 m (6.56 ft.)
• Wavelength: 635 mm (25 in.)
• Angle of incidence: ±80°
• Speed range: 0,1 to 250 000 r/min
• Power input: 5 V DC or 8-24 V DC versions at 30 mA typically
• Operating temperature: –10 to +40 °C (15 to 105 °F)
• IP rating: IP 67
• Housing types: M20 threaded or plain body plus fixing slots
• Connections: Integral connector
• Dimensions: 70 × 20 mm (2.76 × 0.79 in.)
• Weight: 70 g (2.5 oz.)
Kit contents
• Compact laser tachometer
• CMAC 5215: Mounting bracket
• Reflective tape strips
• CMAC 5216: Mini mounting tripod
• CMAC 5214: Tachometer interface cable, 2 m (6.56 ft.)
Compact laser
tachometer
CMAC 5215 mounting
bracket
Reflective tape strips
CMAC 5216 mini
mounting tripod
CMAC 5214 tachometer interface cable
Orderinginformation
• CMAC5030KLaser tachometer kit. Each kit includes a compact laser
tachometer, mounting bracket, cable and mini tripod.
Optional accessories
• CMAC 5215 Mounting bracket
• CMAC 5216 Mini mounting tripod
48
CMAC 5030K-Z2
•
•
•
•
Laser tachometer kit – ATEX certified
The CMAC 5030K-Z2 laser tachometer kit
contains a small tachometer that is ATEX
certified; the sensor is designed for use in
hazardous areas with certified hazardous
area equipment. This kit is primarily
designed for phase-related rotational speed
applications, including very high speed monitoring.
Along with the tachometer, this kit
includes a bracket for mounting the tachometer directly to the SKF Microlog using the
camera mount located on the bottom of the
SKF Microlog. The kit also includes a twometer cable to connect the tachometer to the
SKF Microlog and a small tripod for a stationary mounting of the tachometer during the measurement. The
key features of this laser tachometer kit include:
• Tachometer is ATEX certified
• Operating frequency up to 250 000 r/min
• Long optical range, up to 2 m (6.56 ft.)
• Wide angle of operation, up to 80°
• On target indicator standard
• Protection rating: IP 67
• Integral connector
• Stainless steel housing
• Threaded or plain housing options
• Reverse polarity and short circuit protected
CMXA 45
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
•
•
CMXA 75
CMXA 80
Compact laser
tachometer
CMAC 5215 mounting
bracket
Reflective tape strips
CMAC 5216 mini
mounting tripod
CMAC 5214 tachometer interface cable
Specifications
• Material: Stainless steel housing
• Color: Silver
• Optical range: 100 to 2 000 mm (0.33 to 6.56 ft.)
• Cable: Fischer seven pin type 103 to four pin socket, 2 m (6.56 ft.)
• Angle of incidence: ±80°
• Speed range: 0,1 to 250 000 r/min
• Power input: 5 V DC at 30 mA typically
• Operating temperature: –10 to +40 °C (15 to 105 °F)
• IP rating: IP 67
• Housing types: M20 threaded or plain body plus fixing slots
• Connections: Integral connector
• Dimensions: 70 × 20 mm (2.76 × 0.79 in.)
• ATEX certification: BAS02ATEX3259X
– Ex II 3 G
– EEx nL IIC T6
Kit contents
• Compact laser tachometer
• CMAC 5215: Mounting bracket
• Reflective tape strips
• CMAC 5216: Mini mounting tripod
• CMAC 5214: Tachometer interface cable, 2 m (6.56 ft.)
Orderinginformation
• CMAC5030K-Z2Laser tachometer kit – ATEX certified. Each kit
includes a compact laser tachometer, mounting bracket, cable and
mini tripod.
Optional accessories
• CMAC 5215 Mounting bracket
• CMAC 5216 Mini mounting tripod
49
CMAC 5056 / CMAC 5057 / CMAC 5058
CMXA 45
Modal analysis hammer kit
CMXA 45/75-Z2
•
Features
CMXA 48/80-Z2
• Frequency range up to 8 kHz
• Peak force 2 200 N (500 lb. ft.)
• Output 2,25 mV/N (10 mV/lb. ft.)
• Mass extender to provide additional force
These calibrated modal hammer kits may be
used for impulse testing of the dynamic
behavior of mechanical structures by striking
the object with the hammer and measuring
the resulting response with the accelerometer. The hammer imparts a constant force
over a broad frequency range, which
depends on the type of tip used.
The hammer has an integral, constant
current quartz force sensor mounted on the striking end of the
hammer head. The sensor converts the impact force into electrical
signal for display and analysis.
It is designed with rigid quartz crystals and a built-in, microelectronic, unity gain amplifier. Due to the laser-welded construction of
the sensor element, operation is reliable in adverse environments.
The striking end of the hammer has a threaded hole for installation of a variety of impact tips that are included in the kit. The tip
transfers the impact force to the sensor and protects the sensor face
from damage. Tips of different stiffness allow the variation of the
pulse width and correspondingly the frequency content of the force.
Modal analysis and modeling is also available by fixing the accelerometer at one location, impacting the structure at one point and
then moving the accelerometer to other points of interest. When
used with the FRF module, the following modal parameters can be
calculated and displayed:
• Apparent mass / accelerance
• Impedance/Mobility
• Stiffness/Compliance
50
CMXA 48
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
Specifications
CMAC 5056 Accelerometer (353B04)
Dynamic
• Sensitivity (±5%): 1,02 mV/(m/s2) (10 mVg)
• Measurement range: ±4 905 m/s2 peak (±500 g peak)
• Frequency range:
– ±5%: 1 to 7 000 Hz
– ±10%: 0,7 to 11 000 Hz
– ±3 dB: 0,35 to 20 000 Hz
• Resonant frequency: ≥ 38 kHz
• Broadband resolution (1 to 10 000 Hz): 0,03 m/s2 RMS
(0,003 g RMS)
• Non-linearity: ≤ 1%
• Transverse sensitivity: ≤ 5%
Electrical
• Excitation voltage: 18 to 30 V DC
• Constant current excitation: 2 to 20 mA
• Output impedance: ≤ 100 Ω
• Output bias voltage: 8 to 12 V DC
• Discharge time constant: 0,5 to 2,0 s
• Settling time (within 10% of bias): < 5 s
• Spectral noise:
– 1 Hz: 3 200 µg/√Hz
– 10 Hz: 700 µg/√Hz
– 100 Hz: 180 µg/√Hz
– 1 kHz: 64 µg/√Hz
Environmental
Environmental
• Overload limit (shock): ±98 100
pk (±10 000 g pk)
• Temperature range (operating): –55 to +120 °C (–65 to +250 °F)
• Base strain sensitivity: ≤ 0,0005 g/µ strain
• Overload limit (shock): ±98 100 m/s2 pk (±10 000 g pk)
• Temperature range (operating): –55 to +120 °C (–65 to +250 °F)
• Base strain sensitivity: ≤ 0,002 g/µ strain
Physical
Physical
• Size (hex × height): 12,7 × 29,0 mm (0.50 × 1.14 in.)
• Weight: 10,5 g (0.38 oz.)
• Sensing element: Quartz
• Sensing geometry: Shear
• Housing material: Titanium
• Sealing: Welded hermetic
• Electrical connector: 10-32 coaxial jack
• Electrical connection position: Top
• Mounting thread: 10-32 female
• Size (hex × height): 7,1 × 17,3 mm (0.28 × 0.68 in.)
• Weight: 1,5 g (0.05 oz.)
• Sensing element: Quartz
• Sensing geometry: Shear
• Housing material: Titanium
• Sealing: Welded hermetic
• Electrical connector: 5-44 coaxial
• Electrical connection position: Top
• Mounting thread: 5-40 male
• Mounting torque: 0,90 to 1,35 Nm (9 to 12 in. lbs.)
m/s2
CMAC 5057 Accelerometer (353B16)
CMAC 5056 / CMAC 5057 / CMAC 5058 Hammer
Dynamic
• Sensitivity (±10%): 1,02 mV/(m/s2) (10 mVg)
• Measurement range: ±4 905 m/s2 peak (±500 g peak)
• Frequency range:
– ±5%: 1 to 10 000 Hz
– ±10%: 0,7 to 20 000 Hz
– ±3 dB: 0,35 to 30 000 Hz
• Resonant frequency: ≥ 70 kHz
• Broadband resolution (1 to 10 000 Hz): 0,05 m/s2 RMS
(0,005 g RMS)
• Non-linearity: ≤ 1%
• Transverse sensitivity: ≤ 5%
Dynamic
• Sensitivity (±15%): 2,25 mV/N (10 mV/lb. ft.)
• Measurement range: ±2 200 N peak (±500 lb. ft. peak)
Impact Tips
• Frequency range:
– Hard tip (−10 dB): 8 kHz
– Medium tip (−10 dB): 2,5 kHz
– Soft tip (−10 dB): 375 Hz
– Super soft tip (−10 dB): 200 Hz
• Resonance frequency: ≥ 22 kHz
Electrical
• Excitation voltage: 18 to 30 V DC
• Constant current excitation: 2 to 20 mA
• Output impedance: ≤ 100 Ω
• Output bias voltage: 8 to 12 V DC
• Discharge time constant: 0,5 to 2,0 s
• Settling time (within 10% of bias): < 5 s
• Spectral noise:
– 1 Hz: 3 200 µg/√Hz
– 10 Hz: 700 µg/√Hz
– 100 Hz: 180 µg/√Hz
– 1 kHz: 64 µg/√Hz
51
Kit contents
CMAC 5056 / CMAC 5057 / CMAC 5058 kits include
The CMAC 5056 and CMAC 5057 hammer kits each contain an
accelerometer, while the CMAC 5058 hammer kit does not. The
CMAC 5056 hammer kit can be used on structures with a mass of
210 g (7.6 oz.) and above. The CMAC 5057 hammer kit can be used
on structures with a mass of 56 g (2 oz.) and above.
The accelerometers that are included with the CMAC 5056 and
CMAC 5057 kits are constant current, low impedance, voltage-mode
sensors. Microelectronic, built-in amplifiers standardize sensitivities
within a few percent of nominal value.
• Calibrated hammer
• Cable – BNC to Fischer six pin (for a sturdier cable, CMAC 5088
may be used)
• Red hammer tips (two)
• White hammer tip
• Black hammer tips (two)
• Steel tip
• Blue tip covers (two)
• Petro wax
• Screws threaded on both ends (two)
• Hammer extender
• Carrying case
CMAC 5056 kit also includes
• 353B04 Accelerometer
• Magnetic accelerometer base
• CMAC 5061: Cable – Fischer six pin to Microdot
CMAC 5057 kit also includes
• 353B16 Accelerometer
• CMAC 5062: Cable – Fischer six pin to Microdot
Hammer extender
Calibrated hammer
White hammer tip
52
Black hammer tip
353B04
accelerometer
(CMAC 5056 only)
353B16
accelerometer
(CMAC 5057 only)
Magnetic
accelerometer base
(CMAC 5056 only)
Red hammer tip
Steel tip
Blue tip cover
Petro wax
Screw (threaded on
both sides)
CMAC 5061 cable (CMAC 5056 only)
CMAC 5062 cable (CMAC 5057 only)
BNC to Fischer cable
Carrying case (contents may vary)
Orderinginformation
• CMAC5056Modal hammer kit – for use on structures with a mass of
210 g (7.6 oz.) and above. Includes hammer, accelerometer, magnetic
mount, adhesive mounting base with Petro wax, two cables, carrying
case, certificate of conformance and calibration certificate.
• CMAC5057Modal hammer kit – for use on structures with a mass of
56 g (2 oz.) and above. Includes hammer, accelerometer, adhesive
mounting base with Petro wax, two cables, carrying case, certificate
of conformance and calibration certificate.
• CMAC5058Modal hammer kit includes hammer, BNC cable, carrying
case, certificate of conformance and calibration certificate
(accelerometer not included).
53
CMAC 5059
CMXA 45
Modal analysis hammer kit
CMXA 45/75-Z2
This calibrated modal hammer kit may be
used for impulse testing of the dynamic
behavior of mechanical structures by striking
the object with the hammer and measuring
the resulting response with an accelerometer. The hammer imparts a constant force
over a broad frequency range, which
depends on the type of tip used.
The hammer has an integral, constant
current quartz force sensor mounted on the
striking end of the hammer head. The sensor converts the impact
force into electrical signal for display and analysis.
It is designed with rigid quartz crystals and a built-in, microelectronic, unity gain amplifier. Due to the laser-welded construction of
the sensor element, operation is reliable in adverse environments.
The striking end of the hammer has a threaded hole for installation of a variety of impact tips that are included in the kit. The tip
transfers the impact force to the sensor and protects the sensor face
from damage. Tips of different stiffness allow the variation of the
pulse width and correspondingly the frequency content of the force.
Modal analysis and modeling is also available by fixing the accelerometer at one location, impacting the structure at one point and
then moving the accelerometer to other points of interest. When
used with the FRF module, the following modal parameters can be
calculated and displayed:
• Apparent mass / accelerance
• Impedance/Mobility
• Stiffness/Compliance
Specifications
Dynamic
• Sensitivity (±15%): 0,23 mV/N (1 mV/lbf)
• Measurement range: ±22 240 N peak (±5 000 lbf peak)
• Resonant frequency: ≥ 12 kHz
• Non-linearity: ≤ 1%
54
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
Electrical
• Excitation voltage: 20 to 30 V DC
• Constant current excitation: 2 to 20 mA
• Output impedance: < 100 Ω
• Output bias voltage: 8 to 14 V DC
• Discharge time constant: ≥ 1 400 s
Physical
• Sensing element: Quartz
• Sealing: Hermetic
• Hammer mass: 1,1 kg (2.4 lb.)
• Head diameter: 5,1 cm (2.0 in.)
• Tip diameter: 5,1 cm (2.0 in.)
• Hammer length: 37 cm (14.5 in.)
• Electrical connection position: Bottom of handle
• Electrical connector: BNC jack
Kit contents
• Calibrated hammer
• Super soft plastic, gray tip
• Medium plastic, red tip
• Hard plastic, black tip
• CMAC 5088: Cable – BNC to Fischer six pin
• Carrying case
CMXA 70/44
CMXA 75
CMXA 80
Hammer
Gray hammer tip
Red hammer tip
Black hammer tip
Carrying case
Orderinginformation
• CMAC5059Modal hammer kit. Includes hammer, three tips, cable,
carrying case, certificate of conformance and calibration certificate.
CMAC 5088 cable
55
CMAC 5084
•
Microphone with integral
preamplifier kit
CMXA 45
CMXA 45/75-Z2
•
The CMAC 5084 microphone kit contains an
array microphone for general purpose use.
The constant current microphone enables
acoustic type monitoring and is designed
with a preamplifier. A CMAC 5023 signal
input cable (Fischer six pin to BNC) is included to allow connection to the SKF Microlog.
The kit also includes a calibration certificate.
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
Specifications
Dynamic
• Frequency response (±2 dB): 20 to 10 000 Hz
• Frequency response (–2 to +5 dB): 20 to 20 000 Hz
• Sensitivity (at 1 kHz): 45 mV/Pa
• Inherent noise (1/3 octave at 250 kHz): < 15 dB
• Inherent noise (A weighted): < 30 dB
• Dynamic range (3% distortion limit): > 122 dB
Electrical
• Excitation voltage: 18 to 30 V DC
• Constant current excitation: 2 to 20 mA
• Output bias voltage: 5,5 to 14 V DC
• Output impedance: 150 Ω
Environmental
• Temperature range (operating): –10 to +50 °C (15 to 125 °F)
Physical
• Weight: 18,5 g (0.66 oz.)
• Size (overall): 12,7 × 66,2 mm
(0.50 × 2.61 in.)
• Size (head): 7 × 28 mm (0.28 × 1.10 in.)
• Electrical connector (output): BNC jack
• Housing material: Stainless steel
• Nominal microphone diameter:
6,35 mm (0.25 in.)
Kit contents
CMAC 5023 cable
Microphone with
preamplifier
• Microphone with preamplifier
• CMAC 5023: Signal input cable
• Calibration certificate
Orderinginformation
• CMAC5084Microphone with integral preamplifier kit includes a
microphone with preamplifier, CMAC 5023 cable and a calibration
certificate.
56
CMAC 5208
AC/DC current clamp
•
CMXA 45
CMXA 45/75-Z2
The CMAC 5208 AC/DC current clamp is a battery-powered clampon current probe that is used on primary circuits with the SKF
Microlog Analyzer to measure AC or DC currents up to 600 A peak
AC, 600 A DC.
Features
• Solid state hall effect transducer
• AC (1 Hz to 5 kHz) and DC (0 to 1 Hz) measurement
• Ranges: 60 and 600 A
• Degaussing adjustment for zero noise offset
The AC/DC current clamp allows a user to easily and safely incorporate current monitoring within SKF Microlog routes. The jaws clamp
around a conductor allowing current measurements without breaking the circuit. A Hall Sensor mounted in a gap in the core senses the
magnetic field produced by the current being measured. An amplifier circuit generates an output signal of 1 mV/A (600 A range) or
10 mV/A (60 A range). Demagnetizing (degaussing) is accomplished
by means of a push-button.
Lightweight and easy to carry, the AC/DC current clamp may be
used throughout the plant or in control room environments. This
current clamp is equipped with a connector that fits the CH1 or CH2
input connectors.
Specifications
Electrical
• Current range:
– 40 A (AC) / 60 A (DC) range: 0,2 to 40 A (AC),
(60 A peak) 0,4 to 60 A (DC)
– 400 A (AC) / 600 A (DC) range: 0,5 to 400 A (AC),
(600 A peak) 0,5 to 600 A (DC)
• Output signal:
– 40 A (AC) / 60 A (DC) range: 10 mV/A
– 400 A (AC) / 600 A (DC) range: 1 mV/A on 600 A range on
600 A (DC)
• Output termination: 1,8 m (6 ft.) BNC
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
• Overload: 1 000 A (AC) and 2 000 A (DC) continuous up to 1 kHz
• Rise and fall time:
– 60 A range: ≤ 100 µs from 10 to 90% Vout
– 600 A range: ≤ 70 µs from 10 to 90% Vout
• Insertion impedance:
– 0,39 mΩ at 50 Hz
– 58 mΩ at 1 000 Hz
• Load impedance: > 100 kΩ/100 pF (maximum)
• Frequency range: DC to 10 kHz at −3 dB
• Working voltage: 600 V RMS
• Common mode voltage: 600 V RMS
• Influence of adjacent conductor: < 10 mA/A at 50 Hz at 23 mm
(0.905 in.) from the probe
• Influence of conductor in jaw opening: 0,5% reading
(DC to 440 Hz)
• Influence of temperature: ≤ 300 ppm/°C or 0,3%/10 °C
• Influence of humidity: 10 to 90% relative humidity at reference
temperature ≤ 0,5%
57
Electrical (continued)
Environmental
• Accuracy*:
– 40 A (AC) / 60 A (DC) range:
· 1,5% of reading ±0,5 A (0,5 to 40 A)
· 1,5% of reading (40 to 60 A)
– 400 A (AC) / 600 A (DC) range:
· 1,5% of reading ±1 A (0,5 to 100 A)
· 2,0% of reading (100 to 400 A)
· 2,5% of reading (400 to 600 A DC)
• Phase shift*:
– 40 A (AC) / 60 A (DC) range:
· ≤ 3° (10 to 20 A, 45 to 65 Hz)
· ≤ 2° (20 to 100 A)
· ≤ 1,5° (100 to 400 A)
– 400 A (AC) / 600 A (DC) range:
· ≤ 3° (10 to 100 A)
· ≤ 1,5° (100 to 400 A)
• Noise:
– 60 A range:
· DC to 1 kHz: ≤ 8 mV or 0,8 A PP
· DC to 5 kHz: ≤ 12 mV or 1,2 A PP
· 0,1 Hz to 5 kHz: ≤ 2 mV or 0,2 A PP
– 600 A range:
· DC to 1 kHz: ≤ 1 mV or 1 A PP
· DC to 5 kHz: ≤ 1,5 mV or 1,5 A PP
· 0,1 Hz to 5 kHz: ≤ 500 µV or 0,5 A PP
• Auto off: 10 minutes (may be disabled at power up)
• Electrical certification: EN 61010-2-32
• Case protection: IP 30 per IEC 529
• Operating temperature range: −10 to +55 °C (15 to 130 °F)
• Storage temperature range: −40 to +70 °C (–40 to +175 °F)
• Operating relative humidity:
– 10 to 35 °C (50 to 95 °F), 90% ±5% relative humidity (without
condensation)
– 40 to 55 °C (105 to 130 °F), 70% ±5% relative humidity (without condensation)
• Altitude:
– Operating: 0 to 2 000 meters (0 to 6 500 ft.)
– Non-operating: 0 to 12 000 meters (0 to 39 000 ft.)
*Reference conditions: 18 to 28 °C (64 to 84 °F), 20 to 75% relative
humidity, external magnetic field < 40 A/m, no DC component, no external
current carrying conductor, test sample centered, 1 MΩ ≤ 100 pF load,
zero adjustment prior to measurement (DC only) DC to 65 Hz, battery
voltage = 9 V, ±0,1 V.
Mechanical
• Zero adjustment: Automatic zero
• Battery: 9 V alkaline
• Low battery indication: Green LED when battery voltage ≥ 6,5 V
• Battery life: Approximately 120 hours with alkaline battery
• Overload indication: Red LED indicates input greater than the
selected range
• Jaw opening: 31 mm (1.2 in.)
• Maximum conductor size:
– One 30 mm (1.18 in.) conductor, or
– Two 24 mm (0.95 in.) conductors, or
– Two bus bars 31,5 × 10,0 mm (1.24 in. × 0.40 in.)
• Dimensions: 224 × 97 × 44 mm (8.80 × 3.82 × 1.73 in.)
• Weight: 440 g (15 oz.)
• Vibration: Test per IEC 68-2-6
• Frequency range:
– 5 to 15 Hz, Amplitude: 1,50 mm (0.06 in.)
– 15 to 25 Hz, Amplitude: 1,00 mm (0.04 in.)
– 25 to 55 Hz, Amplitude: 0,25 mm (0.01 in.)
• Mechanical shock: 100 G, test per IEC 68-2-27
Material
• Output lead: Double/Reinforced insulated 1,5 m (5 ft.)
• Handle: Gray polycarbonate + ABS, UL94 V0
• Jaws: Red polycarbonate, UL94 V0
Orderinginformation
• CMAC5208AC/DC current clamp, includes an integral cable that
connects directly to the SKF Microlog.
58
CMCP 850-01 / CMCP 850-02 /
CMCP 850-03
•
CMXA 45
CMXA 45/75-Z2
SKF Microlog Analyzer field balancing
accessory kit
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
Features
•
•
•
• Two accelerometers with magnetic bases
• Choice of optical or laser phase reference kit
• 7,6 m (25 ft.) cables
• Precision electronic balance scale
• Large trial weight kit
• Packaged in a rugged, watertight, hard
carrying case
The SKF Microlog Analyzer field balancing accessory kit contains all of the accessories necessary
to perform in-place field balancing of rotating
machinery. This is a complete kit that provides
the necessary transducers, magnetic bases, A/B
switch, cables, trial weight kit, precision electronic balance scale, and more, all packaged in a
rugged, watertight, hard case that makes balancing easier and more accurate. With the flip of a switch, two channels of vibration data can be input into the SKF Microlog. This eliminates the need to keep moving the vibration sensor back and forth
between balance planes. A variety of adapters are included so that
you can hook the SKF Microlog to other sensor sources, such as online systems and velocity probes.
The CMCP 850 is a complete kit for the SKF Microlog. In short, all
you need to add is an SKF Microlog and you are ready to balance
pumps, fans, motors, couplings, small turbines and more.
Field balancing kits are available with either the optical or laser
phase kits or a laser tachometer kit.
Kit contents
CMCP 850-01 (with Optical Sensor) kit includes
• CMSS 6155XK-U-CE: Optical phase reference kit with universal
power supply
CMCP 850-02 (with Laser Sensor) kit includes
• CMSS 6195AX-K: Laser phase reference kit with universal power
supply
CMCP 850-03 (with Laser Sensor) kit includes
CMXA 70/44
CMXA 75
CMXA 80
CMCP 850-01 / CMCP 850-02 / CMCP 850-03 kits include
• CMSS 2100: Accelerometers (two)
• CMSS 908-MD: Medium duty magnetic bases for
accelerometers (two)
• CMCP 811: Set of assorted balance weights
• CMCP 625: Two pin 5015 to BNC adapters (two)
• CMSS 6156: Magnetic holder
• CMCP 665-6PIN: 7,6 m (25 ft.) BNC to Fisher 103 six pin
accelerometer cables (two)
• CMCP 665-7PIN: 7,6 m (25 ft.) BNC to Fisher 103 seven pin
accelerometer cable (one)
• CMSS T-5: Roll of reflective tape
• 600 g (21.164 oz.) digital scale
• Custom vise grips with M8 thread
• Banana to BNC adapters (three)
• Hex key set
• Tape measure
• Stainless steel rule: 15,2 cm (6 in.)
• Protractor: 180°, 15,2 cm (6 in.)
• Compass
• Clipboard with storage
• Polar plot tablet
• Application notes
• Watertight, hard carrying case
• CMAC 5030K: Laser tachometer kit, SKF Microlog powered
Orderinginformation
• CMCP850-01Microlog Analyzer field balancing accessory kit with
optical sensor.
• CMCP850-02Microlog Analyzer field balancing accessory kit with
laser sensor.
• CMCP850-03Microlog Analyzer field balancing accessory kit with
laser sensor.
59
CMSS 6155XK-U-CE
CMXA 45
Optical phase reference kit
CMXA 45/75-Z2
•
The CMSS 6155XK-U-CE optical phase reference kit allows
you to easily monitor speed and
phase angles on any operating
machine by triggering off of
reflective tape or paint on the
shaft surface. The optical phase
reference system can measure
speed and provide a trigger for absolute and relative phase measurements at distances up to 0,9 m (3 ft.).
The purpose of phase measurement
The angular distance between a reference location on a rotating
shaft and some point defined on the shaft’s vibration waveform
(such as the high spot or heavy spot) is commonly called the phase
angle. Phase angle is measured for four main reasons:
• Balancing, to locate the proper position on an unbalanced rotor
for adding a compensating weight
• Startup and coast down response, to define critical speeds and to
assess system damping
• Detecting changes in operating balance, to indicate problems such
as changing electrical properties, fan build up and shaft cracks
• Detecting shaft misalignment, resonance and other machinery
problems
Methods for establishing a phase reference
Phase angle measurement requires two inputs: a reference pulse
triggered once each revolution and a vibration signal. The SKF
Microlog triggers off a positive-going or negative-going V DC pulse,
depending on how it is configured in the Trigger Slope polarity setting (+ or –) in Trigger Setup.
The once-per-revolution reference pulse required by the SKF
Microlog is provided by a non-contact optical sensing system that
produces a TTL pulse (5 to 0 V DC) when reflective tape or paint
installed on the rotating shaft passes through the sensor’s light
beam, up to a maximum distance of 0,9 m (3 ft.).
The phase angle measuring process
The optical phase reference sensor systems for the SKF Microlog
sense machinery speed and output a TTL signal synchronous with
machine speed. This output signal is used by the SKF Microlog to
measure the absolute phase of a vibration signal.
60
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
The phase angle measuring process works by aiming the sensor’s
light beam, using the optical phase reference sensor, at the reference mark on the rotating shaft. This establishes the zero phase reference relative to the vibration signal component. The vibration
transducer produces a complex vibration signal for the process. The
optical phase reference sensor sends out a phase reference signal to
the SKF Microlog that is synchronous with the shaft speed. The SKF
Microlog then reports the magnitude of the vibration component
and its phase angle in relation to the vibration transducer.
Interface module
The interface module provides an interface between the optical
phase reference sensor and the SKF Microlog. It also provides power
to the sensor. The optical phase reference sensor can typically operate for 40 hours continuously using the interface module’s internal
rechargeable batteries, or indefinitely from the external recharger /
power supply (when connected to the interface module).
Features
• Single pulse per revolution TTL trigger source
• Positive and negative pulse outputs
• Self-contained
• Rechargeable batteries
• Green LED on optical sensor indicates “ON” target operation
• Remote wake-up (with Wireless Monitoring System V/T)
The optical phase reference kit consists of a remote optical sensor
equipped with a steady state DC light source and photo detector, an
interface module, on-off switch, BNC connectors, internal rechargeable batteries and a recharger input. A universal plug-in charger
module is also supplied. Standard camera tripods, user-supplied
mounting brackets or the optional magnetic holder with movable
arm (CMSS 6156) may be used for mounting.
Specifications
Interface module
• Power source: Four rechargeable Nickel Metal Hydride NiMH AA
batteries provide up to 40 hours of continuous operation; complete recharge requires four hours
• Output signals:
– TTL positive inverting pulse: 0 to 5 V
– TTL negative non-inverting pulse: 5 to 0 V – switch selectable
• Bandwidth: 0 to 100 kHz
• Output connectors: BNC connector (female)
• Pulse width: Determined by size of reflective marker and rotational speed of equipment being monitored
• Operating temperature: 0 to 50 °C (30 to 120 °F)
• Weight: 235 g (8.3 oz.)
• Dimensions: 127 × 64 × 25 mm (5.0 × 2.5 × 1.0 in.)
CMSS 6155W interface module
Remote optical sensor
• Speed range: 1 to 250 000 r/min
• Operating envelope: Up to 0,9 m (3 ft.) and 45° from reflective
target
• Illumination source: Visible red LED, 5 V DC at 30 mA
• Output signal: 5 to 0 V DC TTL compatible pulse
• On-target indicator: Green LED on end cap
• Material: 303 stainless steel
• Lens: Acrylic plastic
• Cable length: 2,4 m (8 ft.) from sensor to interface module
• Operating temperature: –10 to +70 °C (15 to 160 °F)
• Dimensions: Threaded tube – M16 × 1,5 mm length × 74 mm
diameter (2.9 in. length × 0.625 in. diameter) supplied with two
M16 jam nuts and mounting bracket
Kit contents
• CMSS 6155W-U-CE: Self-powered sensor
• CMSS 6155W: Interface module
• CMAC 5211: BNC tachometer input cable
• CMSS T-5: Reflective tape
• Mounting bracket with two M16 jam nuts
• Universal recharger / power supply with USA, UK, AUS and EURO
adapter plugs
• User manual
CMSS 6155W-U-CE self-powered sensor
Universal recharger / power supply with adapters
61
Mounting bracket and jam nuts
CMSS T-5 reflective
tape
CMAC 5211 BNC tachometer input cable
Optional accessories
CMSS 50401 extension cable
CMSS 6156 magnetic holder
Orderinginformation
• CMSS6155XK-U-CEOptical phase reference kit includes a selfpowered sensor, BNC tachometer input cable and user manual.
Optionalaccessories
• CMSS50401 7,5 mm (25 ft.) CMSS 6155W Interface module to
optical sensor extension cable
• CMSS6156 Optical phase reference magnetic holder with movable
arm and remote optical sensor attachment hardware
• CMSST-5Reflective tape for use with remote optical sensor, 1,5 m
(5 ft.) roll × 12,7 mm (0.5 in.) wide
62
CMSS 6156
•
Optical phase reference
magnetic holder
CMXA 45
CMXA 45/75-Z2
•
The CMSS 6156 optical phase reference
holder with magnetic base is designed for
use with the CMAC 5030K laser tachometer
kit. It is a magnetic holder with a movable
arm and remote optical sensor attachment
hardware.
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
Specifications
CMXA 70/44
CMXA 75
CMXA 80
• Measurements:
– Magnetic base: 62 × 50 × 55 mm
(2.44 × 1.97 × 2.17 in.)
– Height: 240 mm (9.45 in.)
• Clamping force: 780 N
• Accessory mounting: 355,6 mm (14 in.)
camera type stud
Compatibility
The CMSS 6156 optical phase reference
magnetic holder is compatible with the following kits:
• CMSS 6155XK-U-CE Optical phase reference kit
• CMSS 6195AX-K Smart laser sensor tachometer kit
Orderinginformation
• CMSS6156Optical phase reference magnetic holder.
63
CMSS 6165K-AX
•
Strobe light kit
CMXA 45
CMXA 45/75-Z2
The CMSS 6165 is a truly portable, battery-operated stroboscope that is suited for a wide range of industrial applications and is able to interface with the SKF Microlog
CMXA series.
Sturdy and compact, the strobe can be operated anywhere in the plant or field to permit visual inspection
(freeze motion), phase shift studies and digital measurement of rotary, reciprocating or linear motion of various
equipment while it is in operation. The CMSS 6165 strobe
light has a special “tuning” circuit that allows it to track
vibration transducer (accelerometer) signals. This capability makes it different from general purpose strobe lights. It
also has a narrow and wide bandwidth filter selection to
discriminate fundamentals from harmonics. The narrow
bandwidth filter limits the influence of harmonics around
the selected frequency, providing a more stable phase reading.
The CMSS 6165 requires an input signal to synchronize the flash
rate with an external source, typically a vibration transducer in the
tracking mode or optical pickup in the external mode. Using a cable,
this signal is applied to the input jack connector on the side of the
strobe light. The CMSS 6165 generates a tachometer signal available on the output jack. The CMSS 6165K-AX strobe light kit is ideally suited for:
• Balancing
• Inspection of high speed rotating parts
• Motion analysis or phase shift measurement
• Over-speed trip tests
• On line coupling inspections
• r/min / r/sec measurements
• All applications suited to a general purpose, phase shifting
stroboscope
Specifications
• Time base: Ultra stable crystal oscillator
• Display: LCD with six numeric digits 12,7 mm (0.5 in.) high
• Indicators: Battery level, on target, TIME, AUTO, ALT, TACH, LOCK
and EXT icons
• Knob adjustment: Digital rotary switch with 36 detents per
revolution; velocity sensitive
• Memory: Last setting before power down is remembered and
restored on next power up; nine user flash rates can be set
• Output pulse: 40 microseconds positive/negative pulse (menu
selectable), 3,3 V DC typical
• Input power: Internal rechargeable batteries 6 V DC, external AC
recharger (115 to 230 V AC)
64
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
• Light output:
– Average: 11 W at 3 000 flashes per minute, > 13 W above
3 450 flashes per minute
– Instantaneous (per flash): 230 mJoule typical to 3 450 flashes
per minute
• Flash duration: 10 to 25 microseconds (auto adjust with flash
rate)
• Flash tube (lamp) life: 100 million flashes
• Run time: Two hours typical at 1 800 flashes per minute and over
one hour at 6 000 flashes per minute with fully charged batteries
• Charge time: Four to five hours typical with PSC-pbxU
• Weight: 0,8505 kg (1.875 lbs.) including batteries
This product is designed to be safe for indoor use under the following conditions (per IEC61010-1):
• Operating temperature*: 0 to 40 °C (30 to 105 °F)
• Humidity: Maximum relative humidity 80% for temperatures up to
30 °C (90 °F), decreasing linearly to 50% relative humidity at
40 °C (105 °F)
• Flash range: 30 to 50 000 flashes per minute
• Tachometer measurements: 5 to 250 000 r/min
• Tracking filter: Selectable wide and narrow bandwidths; the filter
may not lock below 100 flashes per minute
• External input: 10 or 100 mVg accelerometer (powered by an
analyzer or by the strobe, menu selectable)
*Safety thermal feature will set unit into TACH Mode (stops flashing) in the
event of internal overheating.
Note: The CMSS 6165 strobe light is not approved for use in hazardous
locations.
Kit contents
• CMSS 6165: Strobe light
• CMAC 5404: Cable – Input to strobe light from the SKF Microlog
• CMAC 5406: Cable – output from strobe light to the SKF Microlog
• Accelerometer input cable with BNC connector, 2 m (6.56 ft.)
• BNC to BNC union connector
• CMAC 5405: Universal power supply / recharger (not compatible
with older SKF Microlog models)
• 58-100-0290: Strobe light jacket and shoulder strap
• 58-100-1650: Spare lamp
• Protective carrying/storage case
• User manual
CMSS 6165 strobe light
CMAC 5404 strobe light input cable
CMAC 5406 strobe light output cable
Accelerometer input cable and BNC to BNC
union connector
CMAC 5405 universal power supply / recharger
Carrying case (open)
58-100-0290 strobe light jacket and shoulder
strap
58-100-1650 spare lamp
Carrying case (closed)
65
Optional accessories
CMSS 6165-SPC strobe light cover
Orderinginformation
• CMSS6165K-AXStrobe light kit, includes a strobe light, cables,
power supply, spare lamp, jacket and shoulder strap, carrying case,
user manual, certificate of conformance and calibration certificate.
Optionalaccessoriesandreplacementparts
• CMAC5404 Cable: Input to CMSS 6165 strobe light from SKF
Microlog
• CMAC5405 Universal power supply / recharger 115/230 V AC for
use with new model CMSS 6165 strobe light
• CMAC5406 Cable: Output from CMSS 6165 strobe light to SKF
Microlog
• CMSS6165-SPC Cover, clear plastic, splash-proof for CMSS 6165
strobe light
• 58-100-0290 CMSS 6165 strobe light jacket and shoulder strap for
hands-free transport
• 58-100-1650 Strobe lamp
66
CMSS 6195AX-K
Smart laser sensor tachometer
•
CMXA 45
CMXA 45/75-Z2
The CMSS 6195AX-K smart laser sensor
tachometer from SKF adds a powerful
dimension to the capabilities of the SKF
Microlog Portable Data Collector / FFT Analyzer. Ideal for measurement modes such as
order/tracking analysis and synchronous
time averaging, the smart laser sensor
tachometer is an essential tool for the proactive machinery analyst.
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
Features
• “Smart” auto gain provides best performance in picking up target
reflections
• Up to 19,8 m (65 ft.) maximum distance – sensor to target
• “On Target” indicator allows correct reflection path and accurate
measurement
• Manual sensitivity knob provides dynamic fine-tuning of sensor
response
• On/Off or charge switch
• Power / Battery condition indicator
• Class 3R visible laser and nose piece
• Accurate measurements from low contrast surfaces
• Normal operation in high ambient light environments
• External DC power or recharger port
• Tripod mounting bushing (1/4-20 UNC)
Specifications
• Laser: Visible red laser diode (650 nm) 3 mW peak power
• Classification: Class 3R laser product (per IEC60825-1)
• Beam diameter: 4 × 7 mm (0.157 × 0.275 in.) typical at
2 m (6.56 ft.)
• Laser diode life: 8 000 hours MTBF
• Operating range: Up to 19,8 m (65 ft.), depending on target
• r/min range: 1 to 150 000 r/min
• Minimum trigger duration: 10 µs
• Power requirement: Internal rechargeable battery
• Charger: 100 to 240 V AC, 50 to 60 Hz with USA, UK, AUS and
EURO adapter plugs
• Output signals:
– TTL positive inverting pulse: 0 to 5 V
– TTL negative non-inverting pulse: 5 to 0 V
• Output connector: DIN-5
• Indicators: On-target, laser on
• Sensitivity adjust: Single knob on top panel
• Modes: Normal, auto and charging
• Dimensions: 137,41 × 59,69 × 54,36 mm (5.41 × 2.35 × 2.14 in.)
• Weight: 300 g (10.6 oz.), excluding cable
• Mounting: 1/4-20 UNC bushing (tripod mount)
• Temperature:
– Operating: -20 to +50 °C (-5 to +120 °F)
– Storage: -30 to +60 °C (-20 to +140 °F)
• Humidity: 90% relative humidity, non-condensing
67
Kit contents
• CMSS 6195A: Self-powered sensor with smart laser sensor
tachometer
• CMAC 5211: BNC tachometer input cable
• SLS-CA-BNC: BNC to five pin DIN cable,
2,5 m (8 ft.)
• 115/230 V AC universal charger with
adapter plugs
• BNC to BNC coupling
• CMSS T-5: Reflective tape
SLS-CA-BNC cable
CMSS 6195A self-powered sensor with smart
laser tachometer
CMAC 5211 BNC tachometer input cable
Universal charger with adapter plugs
BNC to BNC coupling
CMSS T-5 reflective
tape
Optional accessories
Orderinginformation
• CMSS6195AX-KSmart laser sensor tachometer kit, includes a selfpowered sensor complete with a smart laser sensor tachometer,
115 V AC / 230 V AC universal charger with USA, UK, AUS and EURO
adapter plugs, 2,5 m (8 ft.) SLS-CA-BNC cable and reflective tape.
Optionalaccessories
CMSS 6156 magnetic holder
68
• CMSS6156 Magnetic holder with movable arm and laser sensor
attachment hardware
• CMSST-5 Reflective tape for use with the smart laser sensor
tachometer, 1,5 m × 12,7 mm (5 ft. × 0.5 in.)
Power
Battery(CMXA45,CMXA70,CMXA75),CMAC5031 . . . . . . . . . . . . . . . . . . . . . . . . 70
Battery(CMXA48,CMXA80),CMAC5070 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Battery,ATEX(CMXA48,CMXA80),CMAC5092 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Universalpowersupply(non-IS),CMAC5090 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Battery(CMXA51-IS),CMAC5105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Powersupply(CMXA51-IS),CMAC5110 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Strobelightpowersupply,CMAC5405 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
69
CMAC 5031
•
•
Battery
CMXA 45
CMXA 45/75-Z2
CMXA 48
The 7,2 V Lithium-Ion 2,6 Ah rechargeable
battery pack provides customers with eight
hours of continuous data collection or 20
hours idle. The charging time is 2,5 hours.
CMXA 48/80-Z2
CMXA 51-IS
•
•
Specifications
CMXA 70/44
CMXA 75
CMXA 80
Electrical
• Nominal voltage: 7,2 V
• Nominal capacity: 2,6 Ah
• Operating time:
– Eight hours continuous data collection
– 20 hours idling in a process product
• Charge time: 2,5 hours
Environmental
• Temperature range:
– Charging: 0 to 45 °C (30 to 115 °F)
– Rapid charge: 10 to 45 °C (50 to 115 °F)
– Discharging: –20 to +60 °C (–5 to +140 °F)
– Storage:
· 1 week: –20 to +50 °C (–5 to +120 °F)
· 6 months: –20 to +35 °C (–5 to +95 °F)
Physical
• Dimensions: 70,5 × 38,5 × 20,5 mm (2.78 × 1.52 × 0.81 in.)
• Weight: 103 g (3.6 oz.)
• Drop tested to MIL810E, 2 m (6.6 ft.) when installed in a CMXA
70 or CMXA 75
Protection
• Over current (A):
• Short-circuit (A):
• Over voltage (V):
• Under voltage (V):
Minimum
–
–
8,50
4,25
Typical
5,2
3,5
8,6
4,5
Maximum
–
–
8,70
4,75
Approvals
• Emissions: EN61000-6-4:2001 Severity Level Class A
• Immunity: EN61000-6-2:2001 Severity Level Class A
• CSA: Class I, Division 2 Gas groups A, B, C and D (Canadian and
US standards) when installed in a CMXA 70 or CMXA 75
• ATEX: EX II 3 G Ex ic IIC T4 Gc Ta = –10 to +50 °C (15 to 120 °F)
when installed in a CMXA 75
• IECEx: Ex ic IIC T4 Gc Ta = –10 to +50 °C (15 to 120 °F) when
installed in a CMXA 75
• Transportation: UN Directive ST / SG / AC.10/11 Rev.4, Part 111,
sub-section 38.3
• Equivalent Lithium content: 1,47 g (0.0519 oz.)
Orderinginformation
• CMAC5031Battery.
70
CMAC 5070
CMXA 45
Battery
CMXA 45/75-Z2
•
The 7,2 V Lithium-Ion 6 600 mAh
rechargeable battery pack provides customers with eight hours of continuous data collection or 10 hours idle. Charging time is six
hours. The battery can be charged in the
instrument through the docking station
(CMAC 5068).
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
CMXA 75
•
CMXA 80
Specifications
Electrical
• Nominal voltage: 7,4 V
• Nominal capacity: 6,6 Ah
• Operating time:
– Eight hours continuous data collection
– Ten hours idling in a process product
• Charge time: 6 hours (in suspend mode)
Environmental
• Temperature range:
– Charging: 10 to 45 °C (50 to 115 °F)
– Discharging: –10 to +60 °C (15 to 140 °F)
– Storage (1 year): –20 to +20 °C (–5 to +70 °F)
Physical
• Dimensions: 110,3 × 19,5 × 72,0 mm (4.34 × 0.77 × 2.83 in.)
• Weight: 290 g (10.2 oz.)
Protection
• Over current (A):
• Short-circuit (A):
• Over voltage (V):
• Under voltage (V):
Minimum
5,00
14,82
8,65
4,40
Typical
8,33
33,33
8,70
4,60
Maximum
8,89
43,61
8,75
4,76
Approvals
• Emissions: EN61000-6-4:2001 Severity Level Class A
• Immunity: EN61000-6-2:2001 Severity Level Class A
• CSA: Class I, Division 2 Gas groups A, B, C and D (Canadian and
US standards)
• Transportation: UN Directive ST / SG / AC.10 / 11 / Rev.3
• Equivalent Lithium content: 3,96 g (0.1397 oz.)
Orderinginformation
• CMAC5070Battery.
71
CMAC 5092
CMXA 45
Battery, ATEX
CMXA 45/75-Z2
•
•
The 7,2 V Lithium-Ion 6 600 mAh rechargeable
battery pack provides customers with eight
hours of continuous data collection or 10 hours
idle. Charging time is six hours. The battery can
be charged in the instrument through the
docking station (CMAC 5068).
CMXA 70/44
CMXA 75
•
Electrical
• Nominal voltage: 7,2 V
• Nominal capacity: 47,5 Wh/6,6 Ah
• Operating time:
– Eight hours continuous data collection
– 10 hours idling in a process product
• Charge time: Six hours (in suspend mode)
Environmental
• Temperature range:
– Charging: 10 to 45 °C (50 to 115 °F)
– Discharging: –10 to +60 °C (15 to 140 °F)
– Storage (1 year): –20 to +20 °C (–5 to +70 °F)
Physical
• Dimensions: 110,3 × 19,5 × 72,0 mm (4.34 × 0.77 × 2.83 in.)
• Weight: 290 g (10.2 oz.)
Protection
Minimum
5,00
14,82
8,65
4,40
Typical
8,33
33,33
8,70
4,60
Maximum
8,89
43,61
8,75
4,76
Approvals
• Emissions: EN61000-6-4:2001 Severity Level Class A
• Immunity: EN61000-6-2:2001 Severity Level Class A
• CSA: Class I, Division 2 Gas groups A, B, C and D (Canadian and
US standards)
• ATEX:
– EN60079-0:2006, EN60079-11:2007
– EX II 3 G Ex ic IIC T4 Gc Ta = –10 to +50 °C (15 to 120 °F)
• IECEx:
– IEC 60079-0 (Ed.4.0); IEC 60079-11 (Ed.5)
– Ex ic IIC T4 Gc Ta = –10 to +50 °C (15 to 120 °F)
• Transportation: UN Directive ST / SG / AC.10 / 11 / Rev.3
• Equivalent Lithium content: 3,96 g (0.1397 oz.)
Orderinginformation
• CMAC5092Battery.
72
CMXA 48/80-Z2
CMXA 51-IS
Specifications
• Over current (A):
• Short-circuit (A):
• Over voltage (V):
• Under voltage (V):
CMXA 48
CMXA 80
CMAC 5090
Universal power supply
(non-IS)
The CMAC 5090 universal power supply is
used for connecting the docking station to
the power cord. This power adapter delivers
power to the SKF Microlog while charging
the battery when inside the instrument. It
also features a connector to mate with the
USB/splitter cable (CMAC 5095) or the
docking station (CMAC 5068). Since this
universal power supply can support 100 to
240 V input, it also comes with USA, UK,
AUS and EURO adapter plugs.
•
•
•
•
CMAC 5105
CMXA 45
CMXA 45/75-Z2
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 45
Battery
CMXA 70/44
CMXA 75
CMXA 48
The CMAC 5105 battery is the only ATEX
certified battery pack to be used with the
CMXA 51-IS unit. Please read the Battery
Documentation in the CD included in all
applicable kits for important information on
this item.
CMXA 48/80-Z2
•
CMXA 51-IS
CMXA 70/44
CMXA 75
CMXA 80
CMXA 80
Specifications
• Type: NiMH
• Capacity: 1 800 mAh
• Operating time: 8 hours
• Charge time: 8 hours
• Dimensions: 66 × 55 × 21 mm (2.60 × 2.17 × 0.83 in.)
Orderinginformation
Orderinginformation
• CMAC5090Universal power supply, includes four plug adapters.
• CMAC5105Battery.
73
CMAC 5110
CMAC 5405
CMXA 45
Power supply
Strobe light power supply
•
CMXA 45/75-Z2
CMXA 45/75-Z2
CMXA 48
The CMAC 5110 power adapter charges and
powers the battery when connected to the
CMXA 51-IS unit; however, it should only be
used outside hazardous areas.
Note: The CMAC 5110 power supply requires a
country-specific power cord.
CMXA 48/80-Z2
•
CMXA 51-IS
CMXA 70/44
CMXA 45
The CMAC 5405 universal power supply /
recharger supplies 115 or 230 V AC for use
with the CMSS 6165 strobe light. The power
supply also comes with both US and European adapter cables.
CMXA 75
CMXA 80
Specifications
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
• Voltage rating: 8,6 V
• Current rating: 0,6 A
• Cable length requirement: 1 m, ±50 mm
(3.3 ft., ±2 in.)
Orderinginformation
Orderinginformation
• CMAC5110Power supply (IS).
• CMAC5405Strobe light power supply, includes US and European
adapter cables.
74
Miscellaneous accessories
Shoulderstrap(CMXA45,CMXA70,CMXA75),CMAC5010 . . . . . . . . . . . . . . . . . . 77
Shoulderstrap(CMXA48,CMXA80),CMAC5073 . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Shoulderstrap,leather,hazardousareas,CMAC5113 . . . . . . . . . . . . . . . . . . . . . . 78
Handstrap(CMXA45,CMXA70,CMXA70-Z2,CMXA75),CMAC5020 . . . . . . . . . . 78
Handstrap(CMXA48,CMXA80),CMAC5072 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Instrumentsoftcover(CMXA45,CMXA70,CMXA75),CMAC5024 . . . . . . . . . . . . 79
Softcase(CMXA48,CMXA80),CMAC5071. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Carryingpouch,leather,hazardousareas,CMAC5111 . . . . . . . . . . . . . . . . . . . . . . 80
Rubberboot,CMAC5015. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Carryingcase(locationforprinter),CMAC5026. . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Carryingcase,hardshell(CMXA45,CMXA70,CMXA70-Z2,CMXA75),CMAC5029
82
Carryingcase,hardshell(CMXA48,CMXA80),CMAC5069 . . . . . . . . . . . . . . . . . . 82
Carryingcase,hardshell,CMAC5118 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Fischerandaudioconnectorcoverset,CMAC5075 . . . . . . . . . . . . . . . . . . . . . . . . . 83
SDIOanddockconnectorcover,CMAC5083 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Dockingstation(CMXA48,CMXA80),CMAC5068 . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Screenprotector(CMXA48,CMXA80),CMAC5074 . . . . . . . . . . . . . . . . . . . . . . . . . 85
Screenprotector(CMXA45,CMXA75),CMAC6139 . . . . . . . . . . . . . . . . . . . . . . . . . 85
SDmemorycard(4GB),CMAC5077 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
75
Stylus(IS),CMAC5251 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Audioheadset,hardhatcompatible,CMAC5403 . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Labelsformeasurementlocations,CMAC5222 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Idlersoundmonitoraccessories
Audioheadphonescable,CMAC5078. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Microphonewithpreamplifier,CMAC5091 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Signalinputstraightcable(microphonecable),CMAC5093 . . . . . . . . . . . . . . . . . . 89
Parabolicreflector,CMAC5141 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Adapterplate,CMAC5142. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Windjammer,CMAC5143 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
SKFspindleassessmentaccessories
Pullforcegauge,CMAC5121/CMAC5122 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Pullforcegaugetaperrings,CMAC5123throughCMAC5125 . . . . . . . . . . . . . . . . 92
Pullforcegaugeadapters,CMAC5126throughCMAC5136 . . . . . . . . . . . . . . . . . . 92
Run-outgauge,CMAC5137 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Depthmicrometer,CMAC5138 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Belttensiongauge,CMAC5139/CMAC5140 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
76
CMAC 5010
Shoulder strap
•
CMAC 5073
CMXA 45
CMXA 45
Shoulder strap
CMXA 45/75-Z2
CMXA 45/75-Z2
CMXA 48
This shoulder strap fastens directly to the
rubber boot (CMAC 5015) or to the instrument itself. The strap features a metal plate
to hold the sensor/magnet.
CMXA 48/80-Z2
CMXA 51-IS
•
•
CMXA 70/44
CMXA 75
CMXA 80
The CMAC 5073 shoulder strap is adjustable
and features a removable steel plate that
has been designed to hold a few transducers
(if fitted with a magnetic mount). This plate
is attached via two heavy-duty press studs
and can be removed if not required. The
strap also has a safety breakaway. The
breakaway strength is adjustable and may
be set to break easily or not so easily – to
user preference.
Orderinginformation
Orderinginformation
• CMAC5010Shoulder strap.
• CMAC5073Shoulder strap.
•
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
CMXA 75
•
CMXA 80
77
CMAC 5113
Shoulder strap, leather,
hazardous areas
•
•
CMAC 5020
CMXA 45
Hand strap
CMXA 45/75-Z2
•
•
CMXA 48
The CMAC 5113 shoulder strap is part of
the SKF Microlog ATEX certification; it may
be affixed to the SKF Microlog while in use
in a hazardous area.
CMXA 48/80-Z2
•
•
•
CMXA 51-IS
CMXA 70/44
CMXA 75
CMXA 80
CMXA 45/75-Z2
CMXA 48
The hand strap is provided in all kits and is
designed for easier and safer operations of
the instrument. It enables the operator to
hold onto the unit with one hand and still
press the keypad and fire buttons. The hand
strap fastens directly to the rubber boot or
instrument. It does not include a stylus,
although it is equipped with a stylus holder.
Orderinginformation
Orderinginformation
• CMAC5113Shoulder strap, leather, hazardous areas.
• CMAC5020Hand strap.
78
CMXA 45
CMXA 48/80-Z2
•
•
•
CMXA 51-IS
CMXA 70/44
CMXA 75
CMXA 80
CMAC 5072
CMAC 5024
CMXA 45
Hand strap
Instrument soft cover
•
CMXA 45/75-Z2
The hand strap is provided in all kits and is
designed for easier and safer operations of
the instrument. It enables the operator to
hold onto the unit with one hand and still
press the keypad and fire buttons. The hand
strap fastens directly to the instrument.
•
•
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
CMXA 48
This protective carrying case is designed to
provide additional protection to the SKF
Microlog. This instrument cover is to be used
with the leather shoulder strap
(CMAC 5113), which is sold separately.
CMXA 75
•
CMXA 45
CMXA 48/80-Z2
CMXA 51-IS
•
•
CMXA 70/44
CMXA 75
CMXA 80
CMXA 80
Orderinginformation
Orderinginformation
• CMAC5072Hand strap.
• CMAC5024Instrument soft cover.
79
CMAC 5071
CMAC 5111
CMXA 45
Soft case
CMXA 45/75-Z2
The CMAC 5071 soft case includes a plastic
protective sleeve and a pouch that snaps to
the back of the sleeve to hold cables, etc.
These two pieces are only sold together.
•
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
•
CMXA 45
Carrying pouch, leather,
hazardous areas
CMXA 48
The CMAC 5111 carrying pouch is part of
the SKF Microlog ATEX certification; the unit
may be in the carrying pouch while in use in
a hazardous area.
CMXA 48/80-Z2
•
CMXA 51-IS
CMXA 70/44
CMXA 75
CMXA 75
CMXA 80
CMXA 80
Orderinginformation
Orderinginformation
• CMAC5071Soft case, includes protective sleeve and pouch.
• CMAC5111Carrying pouch, leather, hazardous areas.
80
CMAC 5015
Rubber boot
•
•
CMAC 5026
CMXA 45
CMXA 45/75-Z2
Carrying case (location for
printer)
•
CMXA 45/75-Z2
CMXA 48
This protective rubber boot (sleeve) is
designed to provide additional protection to
the SKF Microlog. While it is made out of
heavy-duty rubber, the shoulder strap
(CMAC 5010) should also be purchased.
Note: The CMAC 5015 is shipped with the SKF
Microlog CMXA 51-IS to meet the IECEx
requirements.
Specifications
• Temperature range: –60 to +130 °C
(–75 to +265 °F)
• Material: Santoprene 8000 rubber
• Weight: 130 g (4.6 oz.)
• Dimensions: 20,0 × 12,5 cm (7.9 × 4.9 in.)
CMXA 48/80-Z2
•
•
•
CMXA 51-IS
CMXA 70/44
CMXA 75
CMXA 80
CMXA 45
CMXA 48
The CMAC 5026 carrying/service case contains a location for a portable printer. The
case includes foam cutouts for the SKF
Microlog unit, six accelerometers, a power
supply and spare battery. The case also
includes a pouch for the power cord and
cables, as well as an elastic strap with a clip
fastener used for holding the manual/documentation. The black case is made of double
skinned ABS material, weighs 1 kg (2.2 lb.)
and has dimensions of 45 × 35 × 17 cm
(17.7 × 13.8 × 6.7 in.).
Orderinginformation
Orderinginformation
• CMAC5015Rubber boot.
• CMAC5026Carrying case (location for printer).
CMXA 48/80-Z2
CMXA 51-IS
•
•
CMXA 70/44
CMXA 75
CMXA 80
81
CMAC 5029
Carrying case, hard shell
•
•
CMAC 5069
CMXA 45
CMXA 45/75-Z2
CMXA 45/75-Z2
CMXA 48
The CMAC 5029 hard carrying case includes
foam cutouts for the SKF Microlog, accelerometers and magnetic bases.
CMXA 48/80-Z2
CMXA 51-IS
•
•
CMXA 70/44
The CMAC 5069 hard carrying case includes
foam cutouts for the SKF Microlog, accelerometers and magnetic bases. When opened,
the cover includes a pouch for storing
cables.
•
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
CMXA 75
CMXA 75
•
CMXA 80
Orderinginformation
Orderinginformation
• CMAC5029Carrying case, hard shell.
• CMAC5069Carrying case.
82
CMXA 45
Carrying case, hard shell
CMXA 80
CMAC 5118
CMAC 5075
CMXA 45
Carrying case, hard shell
CMXA 45/75-Z2
Fischer and audio connector
cover set (3)
CMXA 48
The CMAC 5118 carrying case is utilized to
transport and store the SKF Microlog and its
accessories. However, it requires approval by
the site’s safety officer prior to entering a
hazardous area.
CMXA 48/80-Z2
•
CMXA 51-IS
The CMAC 5075 kit consists of a set of three
Fisher connector covers, including two type
103 covers and one type 102 cover.
•
•
•
•
CMXA 45
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
CMXA 70/44
•
•
CMXA 75
CMXA 80
CMXA 75
CMXA 80
Orderinginformation
Orderinginformation
• CMAC5118Carrying case, hard shell.
• CMAC5075Fischer and audio connector cover set (3).
83
CMAC 5083
SDIO and dock connector
cover
The CMAC 5083 SDIO and dock connector
cover attaches to the bottom of the SKF
Microlog with two screws and a tether. The
cover protects the SD memory card slot and
docking station connectors in harsh environments.
CMAC 5068
CMXA 45
CMXA 45/75-Z2
•
•
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
The CMAC 5068 docking station is used for
docking the SKF Microlog while supplying it
with power. This docking station requires the
CMAC 5090 universal power supply.
•
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
CMXA 75
•
CMXA 75
•
CMXA 80
Orderinginformation
Orderinginformation
• CMAC5083SDIO and dock connector cover.
• CMAC5068Docking station.
84
CMXA 45
Docking station
CMXA 80
CMAC 5074
CMAC 6139
CMXA 45
Screen protector
Screen protector
•
CMXA 45/75-Z2
The CMAC 5074 screen protector helps keep
the LCD plastic cover of the SKF Microlog
from scratching. CMAC 5074 includes a set
of five non-glare, self-adhesive screen protectors.
•
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
CMXA 48
The CMAC 6139 screen protector helps keep
the LCD plastic cover of the SKF Microlog
from scratching. CMAC 6139 includes a set
of five replacement screen protectors.
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
•
CMXA 75
•
CMXA 45
CMXA 75
CMXA 80
CMXA 80
Orderinginformation
Orderinginformation
• CMAC5074Screen protector (includes five).
• CMAC6139Screen protector (includes five).
85
CMAC 5077
SD memory card (4 GB)
CMAC 5077 is a 4 GB SanDisk (SD) memory
card for use in the SKF Microlog. Note that
the SKF Microlog series only supports SD
cards (up to 16 GB); the SD memory card is
the only CSA agency-approved memory card
for the SKF Microlog.
Specifications
•
•
•
•
•
•
•
•
CMAC 5251
CMXA 45
CMXA 45/75-Z2
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
CMXA 48
The CMAC 5251 stylus for the SKF Microlog
is safe for use in hazardous areas; any other
kind of stylus would require approval from
the site’s safety officer.
CMXA 48/80-Z2
•
CMXA 51-IS
CMXA 70/44
CMXA 75
CMXA 75
CMXA 80
CMXA 80
• 3,3 V DC
• 10 µF maximum
• 4 GB
A 4 GB version of the SD card is included with each SKF Microlog kit.
Use of any other brand of SD card will result in invalidation of the
instruments’ CSA agency certification.
Orderinginformation
Orderinginformation
• CMAC5077SD memory card (4 GB).
• CMAC5251Stylus (IS).
86
CMXA 45
Stylus (IS)
CMAC 5403
Audio headset, hard hat
compatible
The CMAC 5403 audio headset connects to
the SKF Microlog and allows users to listen
to the audio output as an aid to machinery
diagnostics (such as with the Idler Sound
Monitor). The headphones are high quality
and industrial grade. Special earpiece cups
reduce surrounding noise and are softly
molded to provide comfort during extended
wear. The adjustable fabric head strap and
neck band are designed for environments
where a hard hat must be worn. The audio
connection includes a standard 3,5 mm
(0.14 in.) jack plug.
•
CMAC 5222
CMXA 45
CMXA 45/75-Z2
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
•
•
Labels for measurement
locations
CMXA 75
CMXA 80
The CMAC 5222 labels are used for marking
measurement locations (points) during condition monitoring. These preprinted labels
(stickers) are numbered with horizontal (H),
vertical (V) and axial (A) designations.
Note: These preprinted labels are also available in
the SKF Marine Condition Monitoring kit.
•
•
•
•
•
•
•
•
CMXA 45
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
CMXA 75
CMXA 80
Note: To use the audio headset, the CMAC 5078
audio headphone cable is required.
Orderinginformation
• CMAC5403 Audio headset, hard hat compatible.
Optionalavailability
The CMAC 5403 audio headset is also available in the following two kits:
• CMAC5410 Idler sound monitor accessory kit for SKF Microlog
models CMXA 45 and CMXA 75.
• CMAC5411 Idler sound monitor accessory kit for SKF Microlog
models CMXA 80 and CMXA 48 (kit does not contain CMAC 5142
adapter plate).
Orderinginformation
• CMAC5222Labels for measurement locations (qty. 100).
87
Idler sound monitor accessories
CMAC 5078
Audio headphone straight
cable
The CMAC 5078 cable connects the
CMAC 5403 audio headset to the SKF
Microlog.
•
CMAC 5091
CMXA 45
• Connectors: Fischer type 103 seven pin to
female audio
• Length: 20 cm (7.9 in.) straight
•
CMXA 45/75-Z2
•
CMXA 48/80-Z2
CMXA 51-IS
•
•
CMXA 75
CMXA 80
CMXA 45
CMXA 45/75-Z2
•
CMXA 48
CMXA 70/44
Specifications
Microphone with preamplifier
CMXA 48
The CMAC 5091 is a high frequency microCMXA 48/80-Z2
phone used with the idler sound monitor.
The constant current microphone enables
CMXA 51-IS
acoustic type monitoring and is designed
CMXA 70/44
with a preamplifier.
The microphone is housed within the
CMXA 75
CMAC 5141 parabolic reflector and connectCMXA 80
ed to the SKF Microlog via the CMAC 5093
microphone cable (CMAC 5141 and
CMAC 5093 are sold separately).
When used with the parabolic reflector, the microphone can
detect faulty idlers from up to 3 m (10 ft.) away.
•
•
Note: Refer to page56 for specifications on the microphone.
Note: The CMAC 5091 microphone is the same microphone as supplied with
the CMAC 5084 microphone kit. The CMAC 5091 is sold separately as a
replacement microphone for the idler sound monitor kit.
Orderinginformation
Orderinginformation
• CMAC5078 Audio headphone straight cable.
• CMAC5091 Microphone with preamplifier.
Optionalavailability
Optionalavailability
The CMAC 5078 cable is also available in the following two kits:
• CMAC5410 Idler sound monitor accessory kit for SKF Microlog
models CMXA 45 and CMXA 75.
• CMAC5411 Idler sound monitor accessory kit for SKF Microlog
models CMXA 80 and CMXA 48 (kit does not contain CMAC 5142
adapter plate).
The CMAC 5091 microphone is also available in the following two kits:
• CMAC5410 Idler sound monitor accessory kit for SKF Microlog
models CMXA 45 and CMXA 75.
• CMAC5411 Idler sound monitor accessory kit for SKF Microlog
models CMXA 80 and CMXA 48 (kit does not contain CMAC 5142
adapter plate).
88
Idler sound monitor accessories (continued)
CMAC 5093
Signal input straight cable
(microphone cable)
The CMAC 5093 cable has a BNC connector
on one end to connect to the CMAC 5091
microphone and a Fischer connector on the
other end to connect to the SKF Microlog.
Specifications
• Connectors: Fischer type 103 six pin to
BNC
• Length: 51 cm (20 in.) coiled
•
CMAC 5141
CMXA 45
Parabolic reflector
•
CMXA 45/75-Z2
•
CMXA 51-IS
CMXA 70/44
•
•
CMXA 45/75-Z2
•
CMXA 48
CMXA 48/80-Z2
CMXA 75
CMXA 80
CMXA 45
CMXA 48
The CMAC 5141 parabolic reflector is an
CMXA 48/80-Z2
impact resistant case that holds the
CMAC 5091 microphone. The parabolic
CMXA 51-IS
reflector focuses sounds to the microphone
CMXA 70/44
and protects the microphone from damage.
The parabolic reflector can either be held
CMXA 75
in the hand or attached to the SKF Microlog
CMXA 80
via the optional CMAC 5142 adapter plate
(for models CMXA 45 and CMXA 75 only).
When used with the high frequency
microphone, faulty idlers can be detected from up to 3 m (10 ft.)
away.
On windy days, an optional wind jammer (CMAC 5143) can be fit
over the parabolic reflector to reduce wind noise.
•
•
Orderinginformation
Orderinginformation
• CMAC5093 Signal input straight cable (microphone cable).
• CMAC5141 Parabolic reflector.
Optionalavailability
Optionalavailability
The CMAC 5093 cable is also available in the following two kits:
• CMAC5410 Idler sound monitor accessory kit for SKF Microlog
models CMXA 45 and CMXA 75.
• CMAC5411 Idler sound monitor accessory kit for SKF Microlog
models CMXA 80 and CMXA 48 (kit does not contain CMAC 5142
adapter plate).
The CMAC 5141 parabolic reflector is also available in the following two
kits:
• CMAC5410 Idler sound monitor accessory kit for SKF Microlog
models CMXA 45 and CMXA 75.
• CMAC5411 Idler sound monitor accessory kit for SKF Microlog
models CMXA 80 and CMXA 48 (kit does not contain CMAC 5142
adapter plate).
89
Idler sound monitor accessories (continued)
CMAC 5142
Adapter plate
•
CMAC 5143
CMXA 45
Wind jammer
•
CMXA 45/75-Z2
CMXA 45/75-Z2
CMXA 48
The CMAC 5142 adapter plate (with locking
screw) is used to attach the CMAC 5141
parabolic reflector to the back of the SKF
Microlog (models CMXA 45 and CMXA 75
only).
With the adapter plate attached to the
back of the SKF Microlog, the included velcro
strap neatly holds the CMAC 5093 cable in
place.
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
•
CMXA 45
The CMAC 5143 wind jammer is used to
reduce wind noise that the microphone may
pick up. With its integrated elastic band, the
wind jammer stretches over the CMAC 5141
parabolic reflector until snug.
CMXA 75
CMXA 80
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
CMXA 70/44
•
•
CMXA 75
CMXA 80
Orderinginformation
Orderinginformation
• CMAC5142 Adapter plate.
• CMAC5143 Wind jammer.
Optionalavailability
Optionalavailability
The CMAC 5142 adapter plate is also available in the following kit:
• CMAC5410 Idler sound monitor accessory kit for SKF Microlog
models CMXA 45 and CMXA 75.
The CMAC 5143 wind jammer is also available in the following two kits:
• CMAC5410 Idler sound monitor accessory kit for SKF Microlog
models CMXA 45 and CMXA 75.
• CMAC5411 Idler sound monitor accessory kit for SKF Microlog
models CMXA 80 and CMXA 48 (kit does not contain CMAC 5142
adapter plate).
90
SKF spindle assessment accessories
CMAC 5121 / CMAC 5122
•
Pull force gauges
CMXA 45
CMXA 45/75-Z2
•
Pull force gauges are compact measuring devices used to check the
force of the tool being pulled into the spindle taper. The specified pull
force is very important for the quality of machining. Using the pull
force gauge in preventive maintenance schedules will allow you to
notice a reduction of the pull force and prevent problems before they
occur. The pull force gauge minimizes the down times for your
machines. Two different gauges are available:
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
• CMAC 5121: Measures pull force from 2,5 to 20,0 kN
• CMAC 5122: Measures pull force from 10,0 to 75,0 kN
CMXA 70/44
CMXA 75
CMXA 80
Conventional gauges measure in accordance to the nominal component dimension. The manufacturing related tolerance range of the
components could cause a false measuring result. CMAC 5121 and
CMAC 5122 offer the possibility to take these tolerances into consideration during the measuring process.
All SK work holders from SK30 to SK60 (DIN/ISO/ANSI) and all
HSK work holders according to DIN 69893 (HSK-A 32/B 40 to
HSK-A 125/B 160) can be used.
Features
• Suitable for all types of clamping systems, regardless of
manufacturer
• Exchanging adapters can be used for all tapered standards and
sizes (SK, ANSI, BT, MAS, HSK, CAPTO and special standards)
• The system is light, compact, very easy to use and suitable for
difficult space conditions
• The measured force is easily read on the LED display in kN, even
in difficult lighting conditions
• Power supply includes a standard 9 V DC battery (Auto/Power/
Off)
• Gripping channel for automatic changing and positioning in the
tool magazine
• Automatic mode activates the pull force gauge by itself during the
tool changing
• Adjustable tolerance range to simulate the range of the tool/
spindle (±1 mm increments)
• Energy saving mode for long battery duration
• Internal memory stores up to 8 000 measurements (machine ID,
date, time, pull force, adjusted range)
• USB connection to download the internal memory and charge the
integrated battery
• Operating temperature range between 15 to 35 °C (60 to 95 °F)
• Maximum weight: 1,5 kg (3.3 lb.)
If the pull force falls below a specified value that will eventually occur
due to mechanical fatigue (e.g., spring wear, breakage, etc.), then
one or more of the following will result:
• Tool wear will significantly increase
• The tool vibrates and leaves a bad surface finish
• Fretting occurs in the spindle taper and tool holders
• Unexpected tool breakage
• Reduced tool life
• Safety of the machine operator is at risk
Early preventive actions can be taken to avoid unnecessary machine
shut down and to avoid a number of other problems that cannot be
defined (e.g., excessive tool wear, loss of tool life and tool breakage).
Accessories are available to extend the Spindle Assessment kit
utilization and to maximize the utilization of the Spindle Test module
firmware.
Orderinginformation
• CMAC5121 Pull force gauge, 2,5 to 20,0 kN (base unit).
• CMAC5122 Pull force gauge, 10,0 to 75,0 kN (base unit).
91
SKF spindle assessment accessories (continued)
CMAC 5123 through
CMAC 5125
Pull force gauge taper rings
The CMAC 5123, CMAC 5124 and
CMAC 5125 taper rings are used with the
CMAC 5121 or CMAC 5122 pull force gauge.
These different sized taper rings can be
interchanged based on the size needed. The
different sizes of taper rings available are as
follows:
• CMAC 5123: SK30 (ISO/MAS)
• CMAC 5124: SK40 (ISO/MAS)
• CMAC 5125: SK50 (ISO/MAS)
•
CMXA 45
CMXA 45/75-Z2
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
CMAC 5126 through
CMAC 5136
Pull force gauge adapters
•
CMXA 45
CMXA 45/75-Z2
•
CMXA 48
These adapters are used with the
CMXA 48/80-Z2
CMAC 5121 or CMAC 5122 pull force gauge.
These different sized adapters can be interCMXA 51-IS
changed based on the size needed.
CMXA 70/44
Refer to the ordering information for the
different sizes of adapters that are available.
CMXA 75
The ISO and MAS adapters (CMAC 5126
CMXA 80
through CMAC 5130) are used with the corresponding taper rings (CMAC 5123,
CMAC 5124 or CMAC 5125). Accessories are
available to extend the Spindle Assessment kit utilization and to
maximize the utilization of the Spindle Test module firmware.
•
•
•
These taper rings are used with the corresponding ISO and MAS
adapters (CMAC 5126 through CMAC 5130). Accessories are available to extend the Spindle Assessment kit utilization and to maximize the utilization of the Spindle Test module firmware.
CMAC 5123 SK30
taper ring
CMAC 5124 SK40
taper ring
CMAC 5125 SK50
taper ring
CMAC 5126 SK30
(ISO) adapter
CMAC 5129 SK30
(MAS) adapter
CMAC 5132 32A
(HSK) adapter
Orderinginformation
Orderinginformation
• CMAC5123 Pull force gauge taper ring, SK30.
• CMAC5124 Pull force gauge taper ring, SK40.
• CMAC5125 Pull force gauge taper ring, SK50.
• CMAC5126 Pull force gauge adapter, SK30 (ISO).
• CMAC5127 Pull force gauge adapter, SK40 (ISO).
• CMAC5128 Pull force gauge adapter, SK50 (ISO).
• CMAC5129 Pull force gauge adapter, SK30 (MAS).
• CMAC5130 Pull force gauge adapter, SK40 (MAS).
• CMAC5132 Pull force gauge adapter, 32A (HSK).
• CMAC5133 Pull force gauge adapter, 40A (HSK).
• CMAC5134 Pull force gauge adapter, 50A (HSK).
• CMAC5135 Pull force gauge adapter, 63A (HSK).
• CMAC5136 Pull force gauge adapter, 80A (HSK).
92
SKF spindle assessment accessories (continued)
CMAC 5137
Run-out gauge
•
CMAC 5138
CMXA 45
Depth micrometer
•
CMXA 45/75-Z2
The CMAC 5137 analog run-out gauge (vipp
indicator) is used together with the universal
magnetic foot to measure tool nose run-out
in the Spindle Assessment kit and the Spindle Test module.
The run-out gauge can measure in both
directions and can enable to turn the outer
ring for a zero setting.
CMAC 5137 includes an adapter for an
8 mm fixture and also includes a carrying
case.
•
CMXA 51-IS
•
•
•
CMXA 45/75-Z2
CMXA 48
CMXA 48/80-Z2
CMXA 70/44
CMXA 75
CMXA 80
CMXA 45
The CMAC 5138 depth micrometer is used
to measure ejection measure (EM test) on
spindle tool noses in the Spindle Assessment
kit and the Spindle Test module. CMAC 5138
also includes a carrying case. Accessories are
available to extend the Spindle Assessment
kit utilization and to maximize the utilization
of the Spindle Test module firmware.
•
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
Specifications
• Accuracy: DIN863-2
• Resolution: 0,01 mm (0.0004 in.)
• Scale: 25,0 mm (0.98 in.)
• Pitch: 0,5 mm (0.02 in.)
• Flatness:
– 60 mm: 1,3 µm
– 100 mm: 2,0 µm
• Measuring pressure: 5 to 10 N (3.7 to 7.4 ft. lb.)
Orderinginformation
Orderinginformation
• CMAC5137Run-out gauge.
• CMAC5138Depth micrometer.
93
SKF spindle assessment accessories (continued)
CMAC 5139 / CMAC 5140
•
Belt tension gauge
CMXA 45
CMXA 45/75-Z2
•
The CMAC 5139 and CMAC 5140 belt tension gauges are used to
measure belt tension. By pressing the mechanical gauge on the belt,
it indicates the belt tension value. It verifies the result together in the
Spindle Assessment kit and the Spindle Test module.
CMAC 5139 is used to measure belt tension between
15 and 70 kg (between 30 and 150 lbs.).
CMAC 5140 is used to measure belt tension between
50 and 150 kg (between 100 and 300 lbs.).
CMXA 48
CMXA 48/80-Z2
CMXA 51-IS
•
•
•
CMXA 70/44
CMXA 75
CMXA 80
CMAC 5139 Belt tension gauge
CMAC 5140 Belt tension gauge
Orderinginformation
• CMAC5139 Belt tension gauge, 15 to 70 kg (30 to 150 lbs.).
• CMAC5140 Belt tension gauge, 50 to 150 kg (100 to 300 lbs.).
94
CMAC 4300
CMAC 4321
Accelerometer adapter for SKF Microlog / SKF MARLIN, 1/4-28 stud
Cable, SKF Microlog / PC direct access
CMAC 4400
CMAC 4628
Lens savers for SKF Microlog (5)
Adapter, BNC to LEMO, for CMSS 6190L
CMAC 5004
CMAC 5017
Screen protector
Fischer connector cover set
CMAC 5022
CMAC 5152
Power supply (non-IS)
Adapter cable, 3,5 mm female audio to BNC connector, CMVA 55 / CMVA 60 / CMVA 65
CMAC 5153
CMAC 5211
Audio headphones with 3,5 mm male audio connector, CMVA 55 / CMVA 60 / CMVA 65
Strobe light kit for SKF Microlog Analyzer GX series (CMXA 70) and CMVA series
CMAC 5401-K
CMAC 5402
Audio headphone strobe adapter kit, includes adapter, cables and headphones
Audio headphone strobe adapter, includes adapter and cables (no headphones)
CMSS 2100
CMSS 2100-K
General purpose, two-pin, industrial accelerometer, 100 mV/g (with 1/4-28 and M8 mounting stud)
Industrial accelerometer kit, includes CMSS 908-MD magnetic base and CMSS 60139-04 stinger
CMSS 31476402-CE
CMSS 31707500-CE
Cable, SKF Microlog to CMSS 786M
Cable, SKF Microlog to CMSS 2100 / 2106 / 2200 / 2206 / 787A / 793 / 786A (two pin MIL)
CMSS 376
CMSS 50077A-CE
High temperature accelerometer, charge mode, 260 °C (500 °F)
Cable, CMVA 60 / CMVA 10 / CMVA 40 to support module, 120 cm (4 ft.)
CMSS 50080-CE
CMSS 50139/AUDIO
Cable, support module to PC, 120 cm (4 ft.)
Cable, SKF Microlog audio
CMSS 50156
CMSS 50157
Cable, CMVA 60 / CMVA 10 / CMVA 40 to BNC, with power, 150 cm (5 ft.)
Adapter, SKF Microlog to Microdot (10-32)
CMSS 50162-15
CMSS 50197-CE
Cable, SKF Microlog to BNC, with power, 450 cm (15 ft.)
Cable, SKF Microlog to CMSS 6186 / CMSS TMDT2 (CE compliant)
CMSS 50221
CMSS 50236
Cable, SKF Microlog to CMSS 793V
Standard SKF Microlog connection cable
CMSS 50238
CMSS 50247-2
Cable, SKF Microlog to modem
Cable, SKF Microlog to BNC (3), without diode, 1,5 m (5 ft.)
CMSS 50272-CE
CMSS 50278-CE
Cable, CMSS 793 to SKF Microlog, IS (CE compliant)
Cable, CMSS 6135E adapter to CMSS 6165 strobe light
CMSS 50280-CE
CMSS 50288
Cable, CMVA 65 video out
Cable, CMSS 50289 to CMSS 376
CMSS 50289
CMSS 60139-04
Charge amp SKF Microlog adapter
Probe tip, 11,43 cm (4.5 in.) stinger, 1/4-28 mounting
CMSS 6135E
CMSS 6145K-1
Phase adapter
Adapter, CMSS 6186 and accelerometer with CMSS 50236 cable
CMSS 6155K-U-CE
CMSS 6155VK-U-CE
Optical phase reference kit for use with CMVA 10 and CMVA 40
Optical phase reference kit for use with CMVA 55, CMVA 60 and CMVA 65
CMSS 6160
CMSS 6165-SPC
Printer adapter
Strobe light cover
CMSS 6165K-VA
CMSS 6187-CE
Strobe light kit for SKF Microlog CMVA series
Primary current clamp probe, 60 A / 600 A
CMSS 6190-BNC
CMSS 6195A-K
Audio headphones kit, includes audio headphone and adapter cable, CMVA 55 / CMVA 60 / CMVA 65
Laser phase reference kit (115/230 V), for use with CMVA 60 / CMVA 65
CMXA44
Description
CMXA70
Modelnumber
CMVASeries
Accessories for obsolete products
••
••
•• ••
• •
•• • •
•• ••
••
••
••
••
••
••
••
••
••
••
••
••
••
••
••
••
95
CMSS 786M
CMSS 793LK
Twin sensor, multi-parameter (acceleration/SEE)
Low frequency accelerometer kit
CMSS 793V
CMSS AD-BLANK
General purpose, industrial, two-pin velocity sensor
Stainless steel discs (10 discs per package, minimum order 10 packages)
CMSS R2-2-J5A-10
CMSS R6-2-J5A-10
Cable, BNC to trigger source, 300 cm (10 ft.)
Cable, BNC to CMSS 793, two-pin MIL, 300 cm (10 ft.)
CMSS T-5
CMSS TMDT2K
Reflective tape for optical and laser phase reference
Digital thermometer kit
CMVA 3351
CMVA 3355
Power cord, UL, 110 V, US
AC/DC adapter, universal, for CMVA 6112 only, does not include power cord
CMVA 3355-US
CMVA 50230-4
AC/DC adapter, universal, for CMVA 6112 only, includes CMSS 3351 power cord
Battery pack, NiMH, for CMVA 60, CMVA 10 and CMVA 40
CMVA 6112-CE
CMVA 6112-CE-RU
Support module, enhanced, replaces CMVA 6111 support module
Support module, enhanced, Russian
CMVA 6112K-CE
CMVA 6120-03-02
Support module kit, enhanced, replaces CMVA 6111K
SKF Microlog carrying case, black nylon, for use with CMVA 10 and CMVA 40
CMVA 6121
CMVA 6122
SKF Microlog hard carrying case, pelican, gray, for use with all models of SKF Microlog (foam not cut to shape)
SKF Microlog carrying case, clear plastic moisture protection, for use with all models of SKF Microlog
CMVA 6130
CMVA 6134-HD
SKF Microlog carrying case, black cotton
SKF Microlog hard shell carrying case with logo (foam cut to shape)
10873706
10873707
230 V AC fast recharger for use with strobe light
115 V AC fast recharger for use with strobe light
96
••
••
••
••
••
••
••
••
••
••
CMXA44
Description
CMXA70
Modelnumber
CMVASeries
Accessories for obsolete products (continued)
•• ••
Shoulder strap
Rubber boot
CMAC 5020
CMAC 5023
Hand strap
Signal input straight cable
CMAC 5024
CMAC 5026
Instrument soft cover
Carrying case (location for printer)
CMAC 5029
CMAC 5030K
Carrying case, hard shell
Laser tachometer kit
CMAC 5030K-Z2
CMAC 5031
Laser tachometer kit – ATEX certified
Battery
CMAC 5032
CMAC 5036
Power/Trigger splitter straight cable
CH1 signal input straight extension cable, 5 m (16.4 ft.)
CMAC 5037
CMAC 5043
CH1 signal input straight extension cable, 10 m (32.8 ft.)
Tachometer straight extension cable, 5 m (16.4 ft.)
CMAC 5044
CMAC 5056
Tachometer straight extension cable, 10 m (32.8 ft.)
Modal analysis hammer kit – for structures 210 g (7.6 oz.) and above
CMAC 5057
CMAC 5058
Modal analysis hammer kit – for structures 56 g (2 oz.) and above
Modal analysis hammer kit – without accelerometer
CMAC 5059
CMAC 5061
Modal analysis hammer kit
High frequency accelerometer straight cable
CMAC 5062
CMAC 5068
High frequency accelerometer straight cable
Docking station
CMAC 5069
CMAC 5070
Carrying case, hard shell
Battery
CMAC 5071
CMAC 5072
Soft case
Hand strap
CMAC 5073
CMAC 5074
Shoulder strap
Screen protector
CMAC 5075
CMAC 5077
Fischer and audio connector cover set
SD memory card (4 GB)
CMAC 5078
CMAC 5079
Audio headphone straight cable
Splitter, four channel straight cable
CMAC 5082
CMAC 5083
USB / A to B straight cable
SDIO and dock connector cover
CMAC 5084
CMAC 5087
Microphone with integral preamplifier kit
Temperature gun interface straight cable
CMAC 5088
CMAC 5090
Signal input straight cable
Universal power supply
CMAC 5091
CMAC 5092
Microphone with integral preamplifier
Battery, ATEX
•
• •
• •
•• • •
•
•
•
•
•• ••
•
••
•• •
•
•
••
••
••
••
••
••
••
••
••
••
••
••
••
••
•
•
•
•
•
••
••
••
••
••
•
CMXA80
CMAC 5010
CMAC 5015
••
••
• ••
• ••
••
••
CMXA75
Triax accelerometer kit
Triaxial accelerometer coiled cable
•
••
CMXA70/44
CMAC 4370-K
CMAC 5009
•
••
••
••
••
••
••
••
••
•
CMXA51-IS
Cable converter, two pin MIL to BNC
Infrared thermometer
CMXA48/80-Z2
CMAC 3715
CMAC 4200-K-SL
CMXA48
Description
CMXA45/75-Z2
Modelnumber
CMXA45
Product index
••
••
••
••
••
••
••
••
••
••
••
••
•
••
••
•
•
•• • • ••
•
••
•• ••
•
• ••
•
•
Page
37
46
10
30
77
81
•
78
38
79
81
•
•
82
48
•
••
••
••
••
••
••
••
••
••
••
••
••
••
••
38
35
49
70
36
36
37
50
50
50
54
30
31
84
82
71
80
79
77
85
83
86
39, 88
31
39
84
56
40
40
73
88
72
97
Carrying pouch, leather, hazardous areas
Shoulder strap, leather, hazardous areas
CMAC 5115
CMAC 5116
ATEX certified accelerometer coiled cable
AC/DC signal coiled cable
CMAC 5117
CMAC 5118
Trigger coiled cable
Carrying case, hard shell
CMAC 5121
CMAC 5122
Pull force gauge, 2,5 to 20,0 kN
Pull force gauge, 10,0 to 75,0 kN
CMAC 5123
CMAC 5124
Pull force gauge taper ring, SK30
Pull force gauge taper ring, SK40
CMAC 5125
CMAC 5126
Pull force gauge taper ring, SK50
Pull force gauge adapter, SK30 (ISO)
CMAC 5127
CMAC 5128
Pull force gauge adapter, SK40 (ISO)
Pull force gauge adapter, SK50 (ISO)
CMAC 5129
CMAC 5130
Pull force gauge adapter, SK30 (MAS)
Pull force gauge adapter, SK40 (MAS)
CMAC 5132
CMAC 5133
Pull force gauge adapter, 32A (HSK)
Pull force gauge adapter, 40A (HSK)
CMAC 5134
CMAC 5135
Pull force gauge adapter, 50A (HSK)
Pull force gauge adapter, 63A (HSK)
CMAC 5136
CMAC 5137
Pull force gauge adapter, 80A (HSK)
Run-out gauge
CMAC 5138
CMAC 5139
Depth micrometer
Belt tension gauge, 15 to 70 kg (30 to 150 lbs.)
CMAC 5140
CMAC 5141
Belt tension gauge, 50 to 150 kg (100 to 300 lbs.)
Parabolic reflector
CMAC 5142
CMAC 5143
Adapter plate
Wind jammer
CMAC 5201
CMAC 5208
Serial communication cable
AC/DC current clamp
CMAC 5209
CMAC 5209-06S
Accelerometer coiled cable, 2 m (6.56 ft.)
Accelerometer coiled cable with safety breakaway
CMAC 5209-10
CMAC 5211
Accelerometer coiled cable, 3 m (10 ft.)
BNC tachometer straight cable
CMAC 5213
CMAC 5214
Laser tachometer kit straight cable, 24 cm (9.5 in.)
Laser tachometer kit straight cable, 2 m (6.56 ft.)
CMAC 5222
CMAC 5251
Labels for measurement locations
Stylus (IS)
CMAC 5403
CMAC 5404
Audio headset, hard hat compatible
Strobe light input straight cable
98
• •
••
••
••
••
••
••
••
••
••
••
••
•
••
••
••
•
••
••
••
••
••
••
••
••
••
••
••
••
•
••
•
•
•
••
••
••
•
••
••
•
••
•
CMXA80
CMAC 5111
CMAC 5113
CMXA75
Battery
Power supply
CMXA70/44
CMAC 5105
CMAC 5110
•• • •• •
CMXA51-IS
Signal input straight cable (microphone cable)
USB communication/power splitter straight cable
CMXA48/80-Z2
CMAC 5093
CMAC 5095
CMXA48
Description
CMXA45/75-Z2
Modelnumber
CMXA45
Product index (continued)
• •• ••
••
•• •
••
••
••
••
••
••
••
••
••
••
••
•
• •
••
••
••
•• •
•
Page
44, 89
41
73
74
•
80
78
32
41
••
••
••
••
••
••
••
••
••
••
••
•
••
••
••
•
••
••
••
••
••
••
••
••
••
••
••
•
•
••
••
••
•
••
42
83
91
91
92
92
92
92
92
92
92
92
92
92
92
92
92
93
93
94
94
89
90
90
42
57
32
33
33
34
34
35
87
86
87
43
Screen protector
SKF Microlog Analyzer field balancing accessory kit with optical sensor
CMCP 850-02
CMCP 850-03
SKF Microlog Analyzer field balancing accessory kit with laser sensor
SKF Microlog Analyzer field balancing accessory kit with laser sensor
CMSS 2111
CMSS 2114-K
Small footprint accelerometer with integral cable
High frequency accelerometer kit
CMSS 2200
CMSS 2200-M8
General purpose, low profile, side exit industrial accelerometer
General purpose, low profile, side exit industrial accelerometer with M8 studs
CMSS 2210
Intrinsically safe (IS) industrial accelerometer
CMSS 6155XK-U-CE Optical phase reference kit
CMSS 6156
CMSS 6165K-AX
Optical phase reference magnetic holder
Strobe light kit
CMSS 6195AX-K
CMSS 732A
Smart laser sensor tachometer
Small diameter accelerometer
CMSS 793-CA
CMSS 793-EE
CSA approved, general purpose industrial accelerometer
ATEX approved, intrinsically safe, general purpose industrial accelerometer
CMSS 908-MD
Medium duty magnetic base
CMXA80
CMAC 6139
CMCP 850-01
CMXA75
Idler Sound Monitor accessory kit
Idler Sound Monitor accessory kit
••
•
•
••
••
••
•
•
••
••
••
••
• • • • •
• • • • •
CMXA70/44
CMAC 5410
CMAC 5411
••
•
••
••
••
••
CMXA51-IS
Strobe light power supply
Strobe light output straight cable
CMXA48/80-Z2
CMAC 5405
CMAC 5406
CMXA48
Description
CMXA45/75-Z2
Modelnumber
CMXA45
Product index (continued)
•• •• ••
• •
• •• •
•• •• ••
•• •• ••
•• •• ••
• • •
•• •• ••
•• •• ••
• • •
• • •
Page
74
43
88
88
85
59
59
59
12
14
16
16
18
60
63
64
67
20
22
24
26
99
Please contact:
SKFUSAInc.
ConditionMonitoringCenter–SanDiego
5271ViewridgeCourt•SanDiego,California92123USA
Tel:+1858-496-3400•Fax:+1858-496-3531
Web:www.skf.com/cm
® SKF, MARLIN and MICROLOG are registered trademarks of the SKF Group.
Loctite is a registered trademark of Henkel Corporation
All other trademarks are the property of their respective owners.
© SKF Group 2014
The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written
permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication, but no liability can
be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.
SKF reserves the right to alter any part of this publication without prior notice.
Patents: US 4,768,380 · US 5,679,900 · US 5,845,230 · US 5,854,553 · US 5,992,237 · US 6,006,164 · US 6,199,422 · US 6,202,491 ·
US 6,275,781 · US 6,489,884 · US 6,513,386 · US 6,633,822 · US 6,789,025 · US 6,792,360 · WO/2003/048714 · US 5,633,811 ·
US 5,870,699 · US 6,437,692 · US 7,103,511 · US 7,697,492
skf.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement