keeping your gate front and center

keeping your gate front and center
DKS
Swing Gate operators
KEEPING YOUR GATE
FRONT AND CENTER
­4
Reliable, streamlined designs for
seriously smooth gate operation.
Developed for intermittent and continual use in a variety of applications, from single family residential to
apartment complexes, gated communities, college residence halls, and even commercial facilities. DKS
Swing Gate Operators are available for locations that require column-mount, in-ground, pad, or post-mounted
units to suit virtually any gate and terrain configuration. With options for single or bi-parting gates, DKS
Operators are designed to withstand the elements, deliver reliable access control, and maintain the aesthetic
of your gate.
Model 6300
Model 6550
Model 6400
Model 6004
5
6003 | 6005
Light Duty SWING GATE ACTUATORS
GATE MOUNTED
LOW VOLTAGe
COMPACT DESIGN
DKS 6003 and 6005 Swing Gate
Actuators offer convenience and
reliability in a compact, aesthetic
design. These Actuators mount
directly to your gate and pilaster,
which simplifies installation
without the need for concrete
pads. The powerful screwdriven pistons in these Actuators
connect directly to the gate,
eliminating weak mechanical
connections, and they are fully
enclosed to prevent dirt and
other airborne corrosives from
contaminating the screw threads.
Plus, there is no need to worry
about hydraulic leaks, check
valves or pumps.
Model 6003 Actuator
(for smaller gates)
SOLAR POWER
OPTION
Model 6005 Actuator
(for larger gates)
Solar Powered
Control Box
­6
Solar Power
SOLAR
POWER
Option
OPTION
AC Powered
Control Box
These Actuators feature builtin limit switches that precisely
control the start/stop speed
and travel of your gate. The
microprocessor-based electronic
control board provides many
advanced features not typically
found in Operators in this class,
and with a 24 volt DC operating
voltage, DKS Actuators are ideal
for residential applications.
Solar Panel and Battery
Options Available
Key Features:
• Fully enclosed Screw Drive Actuators
• Adjustable Limit Switches
• Slow Start/Slow Stop: 6003
verlap feature for bi-parting (dual)
•O
non-colliding 2-gate applications
• Motors operate on low voltage (24 VDC)
• Built-in Battery Charger
• Magnetic Lock Output
orts for plug-in Open and Reverse Loop
•P
Detectors (DKS Loop Detectors only)
• Keyed Release for manual operation
ounts directly on gate and gate post,
•M
simplifying installation and eliminating the
need for concrete pads
The elegant lines of the model 6005 provide a clean
profile that will blend with any gate design.
attery backup provides uninterrupted
•B
operation if primary (AC power) is lost
up to 13 ft (3.96 m)
• 1 15 VAC or 24 VDC Solar Powered control
box options
xternal Obstruction Sensing Devices must be
•E
used with these Operators
Small Gates
Swing Gates up to 13 ft (3.96 m), 500 lb (226 kg)
115 VAC and 24 VDC
>
Keyed Release
>
For manual operation
>
Screw drive protects
screw threads
Provides smooth gate
operation for Model 6003
>
Fully Enclosed
Soft Start/Soft Stop
Reliability
In a compact
and simple to
install design
>
Electronic
Control Box
Solar options
available
Residential
7
6004 COLUMN MOUNT
Light Duty SWING GATE OPERATOR
Column
Mounted
LOW
VOLTAGE
WORRY-FREE
DKS 6004 is ideal to operate
swing gates that are mounted on
large columns. The 6004 mounts
directly on the column and simplifies
installation by eliminating the need to
cut niches on the column, and there
is no need for concrete pads. Using a
strong screw drive system, there is no
need to worry about hydraulic leaks,
check valves, or pumps. The 6004
features a keyed release system that
allows the gate to be moved by hand
if a system failure should occur.
Model 6004
SOLAR POWER
OPTION
Solar Powered
Control Box
­8
Solar Power
SOLAR
POWER
Option
OPTION
AC Powered
Control Box
Key Features:
• Adjustable Magnetic Limit Switches
• Slow Start/Slow Stop
•O
verlap feature for bi-parting
non-colliding 2-gate applications
• Motors operate on low voltage (24 VDC)
• Batteries included and built-in battery charger
• Magnetic Lock output
•P
orts for plug-in Open and Reverse Loop
Detectors (DKS Loop Detectors only)
•M
ounts directly on gate and gate post,
simplifying installation and eliminating
the need for concrete pads
•B
attery backup provides uninterrupted
operation if primary (AC) power is lost
The low-profile 6004 column mount Operator is
virtually invisible from the gate entrance.
• 1 15 VAC or 24 VDC Solar powered
control box options
xternal Obstruction Sensing Devices must
•E
be used with these Operators
up to 8 ft (2.4 m)
Small Gates
Swing Gates up to 8 ft (2.4 m), 500 lb (226 kg)
115 VAC and 24 VDC
>
Solar Power
>
Solar panel and battery
options available
Soft Start/Soft Stop
provides smooth
gate operation
>
>
Compact
Reliability in a compact
and simple to install design
Smooth Operation
Dual Gates
Overlap feature
for dual gates
Apartments & College
Residence Halls
Apartment Complex
& Gated Communities
>
Loop
Detectors
Easy plug-in
ports for DKS
loop detectors
Commercial
& Industrial
Self
Storage
Parking
Mixed Use
Buildings
Residential
9
6400 IN-GROUND
Light Duty SWING GATE OPERATOR
THE
UNSEEN
GATE OPERATOR
DKS 6400 installs in-ground,
making it virtually invisible –
and quiet – satisfying the most
sophisticated automation needs
without being detrimental to the
original gate design. Invisible
and powerful, the motor/drive
mechanism is constructed in
die-cast aluminum with a special
corrosion-proof treatment, and
because the drive unit is geardriven, there is no need to worry
about hydraulic leaks, check
valves, or pumps.
SOLAR POWER
OPTION
Model 6400
The in-ground, self-supporting
foundation box is built from
corrosion-proof steel and has a
galvanized steel cover. A lockable
manual release lever is designed
so it can be operated from inside
or outside the gate.
Solar Powered
Control Box
­10
Solar Power
SOLAR
POWER
Option
OPTION
AC Powered
Control Box
Key Features:
•T
he 6400 installs in-ground, making
it virtually unseen and is designed for
residential gates up to 8 ft (2.4 m) long
• Invisible and powerful Gear Drive
•L
ockable Manual Release from inside
or outside
•B
uilt-in Magnetic Limit Switches precisely
control the start and stop speed and travel
of the gate
•P
orts for plug-in Open and Reverse Loop
Detectors (DKS Loop Detectors only)
•B
i-parting non-colliding 2-gate system
controlled from single board
•B
attery backup provides uninterrupted
operation if primary (AC) power is lost
The in-ground 6400 Operator is virtually out of sight,
and stealthily quiet.
• 1 15 VAC or 24 VDC Solar powered control
box options
•E
xternal Obstruction Sensing Devices must
be used with these Operators
up to 8 ft (2.4 m)
Small Gates
Swing Gates up to 8 ft (2.4 m), 500 lb (226 kg)
115 VAC and 24 VDC
>
Solar Power
>
Solar panel and battery
options available
Soft Start/Soft Stop provides
smooth gate operation
>
Electronic
Control Box
Smooth Operation
>
AC/DC versions available
Easy Access
With removable
cover
>
Keyed
Release
For manual
operation
Residential
11
gate safety
for swing & slide operators
PEOPLE ALWAYS
FIND A WAY
TO GET INTO
TROUBLE
­12
At DKS, we take safety a step further
and plan for the unexpected.
In addition to meeting the new UL 325 monitored entrapment protection requirements
with electronic circuits, many DKS Gate Operators are designed with a mechanical clutch
system that relieves pressure on the gate. It’s really quite simple - less pressure equals
less damage, should an unfortunate situation arise. Don’t let Murphy’s Law ruin your day –
plan for the unexpected.
Model 9100
Model 9150
Model 6050/6100
Post Mount
Model 6300
Pad Mount
13
6050 | 6100 | 6300
Continuous Use SWING GATE OPERATORS
aesthetically pleasing
original quiet design
The unique configuration of these
Operators allows the gate arm to
rotate from underneath the Operator,
enabling the arm to attach to the
bottom rail of the gate, were it is
virtually unseen from outside the
gate. The fully enclosed Operators
prevent water from contaminating the
output shaft, bearings, and electronics.
Additionally, the frame is built from
G90 galvanized steel to prevent
rusting. These Operators can be
installed directly on a concrete pad,
or post-mounted to meet any
installation requirements.
With safety in mind, these Operators
contain an electronic and mechanical
inherent reverse system for two
methods of obstruction detection.
The automatic electronic limits,
along with the microprocessor-based
electronic control board provide
advanced features not typically found
in Operators in this class.
Model 6300
Pad Mount
­14
Model 6050/6100
Model 6300
Pad Mount
Post Mount
Key Features:
• Quiet operation
• Weatherproof design
•E
lectronic and mechanical Inherent
Reverse design
•A
utomatic Electronic Limits (gate travel)
never need adjustment
• Microprocessor Electronic Control Board
• Built-in Power and Alarm Reset Switches
• 2-piece Articulating Arm for Slow Start/Stop
•G
ate overlap feature for dual (bi-parting)
non-colliding 2-gate function
• Gate Tracker Reporting output
• Magnetic Gate Lock output
Suitable for single or dual gate configurations.
• Tamper-protect feature
•P
orts for plug-in Open and Reverse Loop
Detectors (DKS Loop Detectors only)
• Keyed Release for manual operation
•C
lutch can be back-driven for failsafe operation
•E
xternal Obstruction Sensing Devices must
be used with these Operators
•B
attery powered Convenience Open option
available on Model 6300 only. Provides a
method to open the gate if AC power is lost
Medium Gates
Swing Gates up to 22 ft (6.7 m), 800 lb (362 kg)
1/2 and 1 HP - 115/208/230/460 VAC
up to 22 ft (6.7 m)
>
>
System reverses gate
on contact
Unique Design
>
Entrapment
Prevention
Apartments & College
Residence Halls
Simplifies installation &
provides easy access to
all internal parts
Smooth Operation
Soft Start/Soft Stop
provides smooth gate
operation
Apartment Complex
& Gated Communities
Commercial
& Industrial
Self
Storage
Parking
Mixed Use
Buildings
Residential
15
Extra Quiet
SWING GATE OPERATORS
QUIET
OPERATION
CONVENIENCE
& Reliability
­16
Unique design for safety, form and function.
DKS 6500 Series Swing Gate Operators offer convenience, reliability and quiet operation in an
aesthetically pleasing design. They are built around a solid steel frame with galvanized steel
control panels to inhibit corrosion. The 2-piece cover simplifies installation and maintenance,
and also features a keyed, easy-to-use disconnect. Unique to the 6500s, a built-in breakaway
clutch protects the gearbox if the gate is struck with sufficient force, saving you hundreds of
dollars in potential repair cost.
Designed with safety in mind, these Operators feature an inherent reverse system, providing
you with peace of mind. The magnetic electronic limits precisely control the travel of your
gate and will never wear out or break. The microprocessor-based electronic control board
provides many advanced features not typically found in Operators in this class.
Model 6550
Model 6500
17
6500 | 6550
Continuous Use SWING GATE OPERATORS/HD
EASY ACCESS design
LOW MAINTENANCE
& QUIET OPERATION
The 6500 Series Operators are designed to
operate Vehicular Swing Gates in residential,
commercial and industrial applications
for both single and bi-parting gates. The
Operator swings gates 90 degrees in
approximately 12-14 seconds.
The unique design of this Operator allows
for easy access to the electronics and
mechanical areas of the Operator
without ever having to remove the
gate arm. The electronic magnetic
limits will never wear out or break
and they are easily adjusted. The
solid steel frame and belt-driven
gear box make this operator
one of the quietest on the
market today.
Model 6500
Model 6550
Heavy Duty
­18
Heavy
Duty
Quiet
Operation
Key Features:
• Quiet operation
• Electronic Inherent Reverse System
• Magnetic Limits and Lock output
• Microprocessor Control Board
• Built-in Power and Reset Switches
-piece Articulating Arm for
•2
Slow Start/Slow Stop
• Gate Tracker Reporting output
•P
orts for plug-in Open and Reverse Loop
Detectors (DKS Loop Detectors only)
• Keyed Release for manual operation
xternal Obstruction Sensing Devices
•E
must be used with these Operators
Dual gate configuration includes non-colliding overlap feature.
up to 25 ft (7.6 m)
6550 Heavy Duty - Large Gates
6500 - Medium Gates
Swing Gates up to 25 ft (7.6 m), 2000 lb (907 kg)
1 HP - 115/208/230/460/575 VAC
1/2 HP Swing Gates up to 18 ft (5.5 m), 700 lb (317 kg)
1 HP Swing Gates up to 22 ft (6.7 m), 800 lb (362 kg)
115/208/230/460 VAC
Easy-to-Adjust
Electronic
Magnetic Limits
One Of The
Quietest
>
>
The solid steel frame and
belt-driven gear box make this
Operator one of the quietest
on the market today
Eliminate old-style
mechanical switches that
can wear out, break, or fail
>
Split Case
Two-piece split polyurethane
housing allows easy
installation and maintenance
>
Breakaway Hub
Unique breakaway hub
design prevents gear box
damage if the gate
is struck
Apartments & College
Residence Halls
Apartment Complex
& Gated Communities
Commercial
& Industrial
Self
Storage
Parking
Mixed Use
Buildings
Residential
19
6524 DC Motor
Continuous use SWING GATE OPERATOR
DC Swing Gate Operator
Battery Back-up
& Solar Power
The newest DKS DC Swing Gate Operator
is perfect where backup power is critical,
as it will keep running even when AC
power has been lost. The solar power
version is ideal in applications where AC
power is unavailable, allowing you to add
your own solar system for power, or you
can choose the DKS solar kit.
This Swing Gate Operator offers versatile
and safe operation in a small, compact
design, and is ideally suited for residential
or commercial applications.
SOLAR POWER
OPTION
20 Watt
Solar Panels
­20
Solar Power
SOLAR
POWER
Option
OPTION
Quiet
Operation
Model 6524
Key Features:
•T
he 6524 rotates the gate 90° in
approximately 12-14 seconds
• 1/2 HP Quadra Drive DC motor
perator mechanics are mounted on a steel
•O
frame plated for corrosion resistance
wo-piece Articulating Arm mechanical Slow
•T
Start/Slow Stop function.
•G
ate overlap feature for dual (bi-parting)
non-colliding 2-gate function
• DC power shut-off switch
•P
orts for plug-in Open and Reverse Loop
Detectors – DKS Detectors only
•E
xternal Obstruction Sensing Devices must
be used with these Operators
Solar kit available for the 6524 Swing Gate Operator. Includes
two 18 Ah batteries and 10 watt, 24 VDC solar panel.
• Continuous operation with AC source power
up to 16 ft (4.87 m)
Medium Gates
Swing Gates up to 16 ft (4.87 m), 800 lb (362.8 kg)
1/2 HP - 115/230 VAC and 24 VDC
>
>
Steel Frame
For strength and durability
Easy Release
For manual operation
>
DC Motor and
Battery Backup
For continued gate
operation if AC power is lost
>
Breakaway Hub
Prevents gearbox damage
Commercial
& Industrial
Residential
21
dks
SLIDE GATE OPERATORS
FROM ONE USER
TO THOUSANDS OF USERS
­22
Security and safety for one and all.
When it comes to moving medium to large gates for a single resident or a mega complex our 9000
series of Slide Gate Operators are a perfect fit. These powerhouses are designed, built and tested in
the U.S. to operate for thousands of maintance-free cycles. Long considered to be the safest Vehicular
Gate Operators on the market, DKS products exceed the UL 325 safety standard and offer both
electronic and mechanical systems to detect obstructions in the opening or closing path of the gate. In
addition, our patented “Fail-Safe” release design is preferred by fire authorities throughout the country.
Model 9050/9100
Model 9150
Model 9000
23
9000
continuouse use SLIDE GATE OPERATORS
POWERFUL &
QUIET OPERATION
The DKS Model 9000 Slide Gate
Operator offers powerful and
safe access control in a small,
compact design. The steel frame
and belt drive/gear-box reduction
system provide a powerful,
yet extremely quiet, slide gate
operation. The 9000 uses an
advanced microprocessor control
circuit with outstanding features.
Designed with versatility in mind,
these Operators will fit most slide
gate operation requirements.
These Operators are ideally used
in residential, commercial or
industrial high-use applications.
Model 9000
­24
Quiet
Operation
Key Features:
•D
irect-driven Limit Nuts for precise gate
limit control
• Auto-close Timer 1-30 seconds
•S
electable Loop/Reverse Input function;
stop or reverse
orts for plug-in Open and Reverse Loop
•P
Detectors (DKS Loop Detectors only)
•G
ate Tracker Reporting output provides
operator data to DKS Access Control System
•S
teel frame provides strength and
quiet operation
• Anti-tailgating feature
•G
ate Overlap feature for dual (bi-parting)
non-colliding 2-gate function
The powerful 9000 Slide Gate Operator is suitable for residential,
commercial, and industrial high-use applications.
• Two 115 VAC Convenience Outlets
• 5-year Limited Warranty
•E
xternal Obstruction Sensing Devices must
be used with these Operators
up to 35 ft (10.7 m)
Large Gates
Slide Gates up to 35 ft (10.7 m), 1500 lb (680.3 kg)
1/2 and 1 HP - 115/208/230/460 VAC
>
Entrapment Prevention
>
Reverses gate when obstructed
Built-in power switch
and alarm reset switch
>
Adjustable
Partial Open
Easy Access
>
For different opening distances
“T-Handle”
Release
For easy manual
operation
>
Precise
Limit
Control
Simple setup
Commercial
& Industrial
Residential
25
9024 DC MOTOR
continuous use SLIDE GATE OPERATORS
DC Slide Gate Operator
Battery Back-up
& Solar Power
The 9024 can run
exclusivly on AC
power with battery
back up, or solely on
solar power.
The newest DKS DC Slide Gate
Operator is a great option
where backup power is critical,
as it’s designed to keep running
when AC power has been lost.
The solar power version is ideal
in applications where AC power
is unavailable, with the option
to add your own solar system
for power, or you can use the
DKS solar kit.
SOLAR POWER
OPTION
The DKS 9024 DC Slide Gate
Operator offers powerful, yet
safe, multifunctional operation
all in a small, compact design –
ideally suited for residential or
commercial applications.
20 Watt
Solar Panels
Model 9024
­26
Solar Power
SOLAR
POWER
Option
OPTION
Quiet
Operation
Key Features:
•O
perator is 24 volt DC and includes
built-in battery backup
•A
djustable Limit Nuts for precise gate
limit control
• Easy-to-use manual T-handle release
• Heavy-duty Gearbox
• 0.0 amp SBPD Circuit (solar power only)
• Solar power ready
• Heavy-duty steel frame
• 5-year Limited Warranty
•E
xternal Obstruction Sensing Devices
must be used with these Operators
• Continuous operation with AC source power
9024 DC Slide Gate Operator can be run exclusively by solar
power for remote locations where AC power is not available.
up to 40 ft (12.2 m)
Large Gates
Slide Gates up to 40 ft (12.2 m),
1000 lb (453.6 kg)
1/2 HP - 115/230 VAC and 24 VDC
>
Built-in (7.2 AH battery x2)
>
Battery Backup
“T-Handle” Release
For easy manual open
or close
>
Quadra Drive
DC motor for longer life
>
Full Size Gearbox
Heavy-duty 30:1 ratio gearbox
Commercial
& Industrial
Residential
27
9050 | 9100
continuous use SLIDE GATE
BUILT-IN
RESIDENTIAL
SAFETY FEATURES
DKS 9050 and 9100 Slide Gate
Operators provide durability
through high-cycle usage, all in a
solid design. The innovative
fail-safe design of these
Operators significantly
reduces the chance of injury or
entrapment and makes these
Operators the safest residential
Slide Gate Operator in the
market today. Designed with
versatility in mind, the 9050
and 9100 Operators can be
configured for front, center or
rear drive applications and
can be pad or post mounted.
These Operators are ideally
used in residential and
commercial applications.
Model 9050/9100
­28
Key Features:
• Automatic Magnetic Limits
•B
uilt-in mechanical and electronic
Reverse System
• Built-in Power and Alarm Reset Switches
• Selectable Loop Function (stop and reverse)
•P
orts for plug-in Open and Reverse Loop
Detectors (DKS Loop Detectors only)
• Convenience Outlets
•E
xternal Obstruction Sensing Devices must
be used with these Operators
up to 16 ft (4.87 m)
9050 - Medium Gates
Swing Gates up to 16 ft (4.87 m), 500 lb (227 kg)
1/2 HP - 115 VAC
up to 30 ft (9.1 m)
9100 - Large Gates
Slide Gates up to 30 ft (9.1 m), 1000 lb (453.6 kg)
1/2 HP - 115 VAC
>
Never be locked out (or in)
>
Fail-Safe Release
Entrapment
Prevention
Reverses gate when obstructed
>
Unique Design
Allows easy access to
all mechanical parts
>
Convenient
Built-in power switch
and reset switch
Commercial
& Industrial
Residential
29
9150
continuous use SLIDE GATE OPERATORS
THE SAFEST
WORRY-FREE
SELF ADJUSTING
GATE OPERATORS
This Slide Gate Operator delivers
the convenience of self-setting
limits with the safe operation you
expect from a DKS Operator.
This Operator can be used
in residential, commercial or
industrial high-use applications,
with an innovative fail-safe
design which significantly
reduces the chance of injury or
entrapment and makes this the
safest Slide Gate Operator in
the market today. Designed to
work in many configurations, this
Operator can be used for front,
center or rear drive applications
and can be pad or post mounted.
Model 9150
­30
Key Features:
•E
lectronic Magnetic Limits eliminate
old-style mechanical switches that can
wear out, break or fail
•A
utomatic Self-setting Limits mean no limit
switch adjustments – ever
•B
uilt-in mechanical and electronic
Reverse System
• Special Anti-tailgating feature
•P
orts for plug-in Open and Reverse Loop
Detectors (DKS Loop Detectors only)
• Built-in Power and Alarm Reset Switches
• Convenience Outlets
•E
xternal Obstruction Sensing Devices must
be used with these Operators
Dual 9150 Operators at the Los Angeles Harbor Fire Department.
•B
attery-powered Convenience Open option
available, which provides a method to open
the gate if AC power is lost
up to 45 ft (13.7 m)
Large Gates
Slide Gates up to 45 ft (13.7 m),
1500 lb (680.8 kg)
1/2 and 1 HP - 115/208/230/460 VAC
>
Entrapment Prevention
>
Automatically assumes fail-safe mode
when an entrapment condition exists
Unique Design
Allows long gates to open 14 ft
(4.2 m) for automobile traffic, or
opens gate fully for large trucks
or oversized vans
>
>
Allows easy access to all
mechanical parts for easy
repair and maintenance
Partial Open
Fail-safe
Release
Never be locked
out (or in) of
your property
>
Convenient
Built-in power
switch and
reset switch
Apartment Complex
& Gated Communities
Self
Storage
Parking
Residential
31
MAXIMUM SECURITY heavy duty
SLIDE GATE OPERATORS
PROTECTION
WHERE IT
REALLY COUNTS
­32
A higher degree of perimeter security.
The DKS 9200 and 9500 Series of Vehicular Slide Gate Operators are ideal for airports,
seaports, military bases, government buildings, border fences, and infrastructure (electric
plants, water treatment facilities, dams, etc.). Advanced features on these models include
anti-tailgating, adjustable mid-stop, and tamper-proof internally driven limit switches.
A solid-state speed controller features slow-start and slow-stop operation and allows the user
to set the speed of the gate from 1/2 to 2 ft/sec (.15 to .61 m/sec), except model 9210, and
on certain models up to 4 ft/sec (1.22 m/sec). An emergency close feature at 6 ft/sec (1.83
m/sec) is also available on certain models. These Operators can handle gates up to 160 feet
(48.7 meters) in length and weighing up to 25,000 pounds (11,340 kilograms).
Ideal for large airport gates up to 160 feet.
Model 9200
Series
Strong motors and structure design can
move gates weighing up to 25,000 pounds.
Model 9500
Series
33
9200 SERIES HEAVY DUTY
MAXIMUM SECURITY
MORE APPLICATIONS
MAXIMUM SECURITY
MAXIMUM CHOICES
WITH SPEED
CONTROLS
DKS 9200 Series Operators are
designed for maximum security
applications only – such as industrial
locations, loading docks, factories,
prisons, airport security areas, sea
ports, etc. Because of the need to
prioritize security in these applications,
these Operators are designed for
fail-secure operation and require
manual operation to open the gate
in the event of a power outage. To
enhance security, these Operators
feature an anti-tailgating circuit and
an adjustable partial open feature to
help prevent unauthorized vehicle
access. In addition, speed controller
options allow the user to adjust the
gate speed from 1/2 ft/sec up to 4 ft/
sec. An Emergency Close feature is
available on some models which will
close the gate at 4 ft/sec. This assures
your security gate is open the absolute
minimum amount of time necessary.
Model 9200
Series
Model 9200 Series
Pedestal Mount
­34
Heavy Duty
Key Features:
•A
dvanced Microprocessor Control Board
features programming switches to set the
mode of operation required and includes
built-in diagnostics
• Special Anti-tailgating and partial open
• Selectable Loop Function (stop or reverse)
orts for plug-in Open and Reverse Loop
•P
Detectors (DKS Loop Detectors only)
• Warn-before-operate feature
• Built-in Power and Alarm Reset Switches
amper-proof Direct Drive Limit Switches
•T
for precise gate control
• Fail-secure operation to prioritize security
Some 9200 Models include a heavy duty pedestal.
• Gate Tracker Reporting output
• Convenience Outlets
•E
xternal Obstruction Sensing Devices must
be used with these Operators
up to 100 ft (30.48 m)
Larger Gates
Slide Gates up to 100 ft (30.48 m), 8000 lb (3.6 metric ton)
Minimum gate length of 10 ft (3.04 m)
1, 2, 3 HP - 1 and 3 phase - 115/208/230/460 VAC
>
for different
opening distances
>
Adjustable
Partial Open
Chain Drive
for a direct mechanical
connection to the gate
>
Gate Tracker™
Provides Operator data to
companion access controller
(DKS 1833, 1835, 1837, 1838)
>
Adjustable Speed
Motor Drive
for precise control
Commercial
& Industrial
Maximum
Security
35
9500 SERIES HEAVY DUTY
MAXIMUM SECURITY
THE WORK HORSE OF
MAXIMUM SECURITY
WITH RACE HORSE
FEATURES
DKS 9500 series of Vehicular
Slide Gate Operators are designed
for use on very large and very
heavy gates in maximum security
applications only. These Operators
must never be used in applications
serving the general public. These
heavy duty Operators use a high
tensile steel alloy roller chain as the
pulling medium, which is immune
to slippage and the challenges of
uneven terrain – and also simplifies
installation. User can set the
speed of the gate up to 4 ft/sec.
(1.2 m/sec.), with an electronic
braking option.
Model 9500
10 Gauge
Housing
Model 9500
Series
­36
Heavy Duty
Key Features:
• Slow Start and Stop
• Adjustable Partial Open limit
• Selectable Stop/Reverse Loop function
•T
amper-proof Direct Driven Limit Switches
for precise gate control
uilt in Power and Reset Switches and
•B
3-button Control Station (open-close-stop)
• 115 volt Convenience Outlets
•P
orts for plug-in Open and Reverse Loop
Detectors (DKS Loop Detectors only)
• Warn-before-operate function
•E
xternal Obstruction Sensing Devices
must be used with these Operators
Power to move massive gates up and down hills.
vailable with 10 gauge heavy-duty
•A
steel housing
up to 160 ft (48.77 m)
Larger Gates
Slide gates up to 160 ft (48.77 m), 25,000 lb (11.3 metric ton)
Minimum gate length of 25 ft (7.62 m)
3 and 5 HP - 3 phase - 208/230/460 VAC
>
>
Large Gates
Gates up to 160 ft (48.7 m)
and 25,000 lb (11,340 kg)
Gate Tracker™
Provides Operator data to
companion access controller
(DKS 1833, 1835, 1837, 1838)
>
User Adjustable
Variable Speed
Adjustable speed
control circuit
>
Limit Switches
Direct driven for
precise gate control
Commercial
& Industrial
Maximum
Security
37
GATE
ACCESSORIES
SWING GATE
HINGES & UPHILL ASSISTS
Swing Gate Hinge Assemblies
•H
eavy-duty flange bearing Hinge Assemblies for
gates up to 3000 lb (1,360 kg)
•S
ealed bearing Hinge Assemblies for gates weighing
2000 and 3000 lb (907 kg and 1,360 kg)
ll Hinge Assemblies include mounting hardware
•A
and brackets
SLIDE GATE END
RETAINER &
CHAIN IDLER ASSEMBLY
The DKS Chain Idler Assembly (or endless
idler) is used with Slide Gate Operators that
are installed in rear mount applications. End
retainers are used to provide a catch for the
gate to slip into in the closed position.
Slide Gate Idler Assembly
•U
se when rear mounting Slide
Gate Operators
• Chain guide is enclosed
• Easily mounts to a wall or pilaster
• Use with #40 or #41 chain
Swing Gate Torsion Rod Assembly
Slide Gate End Cap
• Counter-balances uphill swing gates
• Heavy-duty galvanized steel
• Includes top bracket, bottom bracket
and torsion rod
• Beveled opening
•A
dd up to 5 additional torsion rods
for heavier gates
• Helps to prevent gate runaway
•D
esigned for slide gates
with 2” (50.8 mm) frames
apped to prevent gates from
•C
being lifted off the track
Ball Joint Pivot Assembly
•U
sed to connect Operator arm
when the Operator has been
installed horizontally level and
the gate opens on an uphill or
downhill slope
Gate end cap.
Counter balance for uphill swing gates.
­38
SLIDE GATE Guarded
Guide Rollers
Designed to meet the requirements of the UL 325 and ASTM
F2200 standards. The rollers are fabricated from UHMW
material for long-lasting quiet operation.
• Single 3” (76.2 mm) UHMW Guide Roller and mounting bracket
• Dual 3” (76.2 mm) UHMW Guide Rollers and mounting bracket
•T
wo single 3” (76.2 cm) UHMW Guide Rollers stacked to
provide a 6” (152.4 mm) surface area and mounting bracket
•D
ouble dual 3” UHMW Guide Rollers stacked to provide a 6”
(152.4 mm) surface area and mounting bracket
Guarded Guide Rollers.
SLIDE GATE WEIGHT BALANCED
V-WHEELS
DKS provides a full line of V-Wheel Assemblies and
replacement V-Wheels to meet any slide gate application
and budgetary requirements.
Tandem Assembly for heavy gates.
V-Wheel Assemblies for Standard Gates
• 4” (101.6 mm) UHMW wheel with sleeve bearing – for gates up to 500 lb (226 kg)
• 4” (101.6 mm) UHMW wheel with roller bearings – for gates up to 750 lb (340 kg)
• 4” (101.6 mm) Steel wheel with roller bearings – for gates up to 1500 lb (680 kg)
Tandem V-Wheel Assemblies for Heavy Gates
Replacement V-Wheels
•T
wo 4” (101.6 mm) UHMW wheels with roller bearings
- for gates up to 1500 lb (680 kg)
• 4” (101.6 mm) UHMW wheel with sleeve bearing
•T
wo 4” (101.6 mm) steel wheels with roller bearings
- for gates up to 3000 lb (1,360 kg)
• 4” (101.6 mm) Steel wheel with roller bearings
•T
wo 6” (152.4 mm) steel wheels with roller bearings
- for gates up to 5000 lb (2,267 kg)
Apartments & College
Residence Halls
Apartment Complex
& Gated Communities
• 4” (101.6 mm) UHMW wheel with roller bearings
• 6” (152.4 mm) Steel wheel with roller bearings
Commercial
& Industrial
Self
Storage
Parking
Mixed Use
Buildings
Maximum
Security
39
GATE
ACCESSORIES
CONTROL STATIONS
Gate Operator Control Stations provide
complete manual control for DKS vehicular
Gate Operators. The unique logic inputs found
on DKS Gate Operators require only 3 wires
for connection to a 3-button control station.
Three Button Interior
Model 1200-007
• Open - Close - Stop gate control
• Mounts into single-gang electric box
• All switch contacts are dry contact normally open
1200-007
3-Button Interior
vailable for most DKS Gate Operators
•A
(cannot be used with Model 9000)
Three Button Exterior
Model 1200-006
• Open - Close - Stop gate control
• Surface or post mount
•A
vailable for most DKS Gate Operators
(cannot be used with Model 9000)
Gate Control Toggle
Model 1200-017
• Three-position control toggle for automated gates
• Center position is neutral for normal operation
• Down position is momentary contact to open gate
• Up position is toggled to hold gate open
• Mounts into single-gang electric box
1200-006
3-Button Exterior
Gate Control Toggle
Model 1200-017
• Three-position control toggle for automated gates
1200-017
Manual Control
Interior
• Center position is neutral for normal operation
• Down position is momentary contact to open gate
• Up position is toggled to hold gate open
• Mounts into single-gang electric box
­40
LOCK BOXES &
ACCESSORIES
Postal and Fire Department Lock Boxes
provide a convenient method to allow postal
workers and fire department personnel
access to a property through an automated
gate system. The 1200 Transformer Box is
a great way to provide a power source for
accessory transformers used with Access
Control Systems.
Postal and Fire Department Lock Boxes
• 1402 accepts standard postal key
• 1401 Fire Dept. Box accepts the Knox 3501 key switch
1402 Postal
• 1 400 accepts a Fire Dept. padlock or any
standard padlock
Lock Box
1400 Fire Dept.
1401 Fire Dept.
Lock Box
Lock Box
Lock Boxes allow quick access for fire dept. personnel.
Auxiliary Transformer Box
• Lockable Transformer Box
• Holds up to four 20 VA transformers
• Indoor or outdoor use
• ETL Listed
Transformer Box
Apartments & College
Residence Halls
Apartment Complex
& Gated Communities
Commercial
& Industrial
Self
Storage
Parking
Mixed Use
Buildings
Maximum
Security
41
MONITORED
ENTRAPMENT PROTECTION
tyPE B1
NON-CONTACT SENSORS
Intended to be positioned in such a way that an obstruction in
a hazardous area will interrupt the light beam. An interruption
of the beam will signal the Operator to either stop, or stop and
reverse motion. Complies with monitored external entrapment
protection as per UL325-2016.
RG Reflecti-GUARD
8080-051
Reflective Photo Eyes
Reflective Photo Optic Systems consists of an emitter/receiver
unit and a reflector. Since the Reflector directs the beam back
to the Photo Eye, wiring to the other side of the roadway is not
required. These are typically used with shorter gates.
RG Reflecti-GUARD
• Infrared beam range 7-30 ft (2.1-9.1 m)
• Mounting hardware included
• Available as Relay Output or Pulsed Output
• Power: 7-30 VAC (50/60 Hz) or 10-42 VDC, 75mA
IRB-RET
• Pulsed near infrared light beam range 60 Ft (18.3m)
• Available with or without Reflector
• Includes mounting bracket with hardware
• Operates over a wide range of 6-35 VDC and 12-24 VAC
ENFORCER
IRB-RET
8080-056
• Mounting bracket and Reflector housing included
• Adjustable range up to 45 ft (14m)
• 12-30V DC/AC 60H, 100mA
Thru-Beam Photo Eyes
Enforcer
Thru-Beam Photo Eye Systems consist of one Infrared Emitter
and one Infrared Receiver housed and powered in separate
units. These are typically used with longer gates.
8080-055
IRB-MON
• Infrared LED beam range 115 ft (35m)
• Includes Emitter and Receiver
• Mounting bracket, other options available separately
• Operates over a wide range of 6-35 VDC and 12-24 VAC
IRB-MON
8080-052
­42
tyPE B1
NON-CONTACT SENSORS
PG Prime-GUARD
Emitter:
• 50 ft (15.2 m) and 100 ft (30.5 m) battery models and
100 ft (30.5 m) wired model
Prime-GUARD
8080-050
• Mounting brackets and hardware included
Receiver:
• Available as Relay Output or Pulsed Output
• Front-mounted green LED alignment light
• Top-mounted LED lights for power, low battery, fault
• Power supply: 7-30 VAC (50/60Hz) or 10-42 VDC, 100mA
• Optional extension pedestal available
TYPE B2
CONTACT SENSORS
Complies with monitored external entrapment protection as
per UL325-2016.
Contact (Type B2) Sensing Edges
• A variety of edge styles for different gates
• Mounting channels included
• T2 (resistive) termination
Contact Sensing Edges
CONTACT SENSOR ACCESSORIES
Wireless Monitored Gate Sensing Edge (Type B2) Link
Provides a wireless connection between a Monitored Safety
Edge and an Operator that controls the associated gate.
• Includes Transmitter, Receiver and Antenna
• Includes Transmitter 2 AA batteries
•R
eceiver power 12-24 VAC/DC nominal (8-30V max); power may be supplied
from the Operator or from an external supply
Monitored Gate Link
• Meets UL325-2016 requirements for monitored devices
8080-009
MIM-62
Multi-Input Module
Accepts up to 6 separate entrapment protection devices and
connects them to either of two outputs. Is compatible with
either Type B1 or B2 devices.
•P
owered from any 12 or 24 volt source, AC or DC, that can supply
at least 100mA
MIM-62
8080-079
Apartments & College
Residence Halls
Apartment Complex
& Gated Communities
Commercial
& Industrial
Self
Storage
Parking
Mixed Use
Buildings
Maximum
Security
43
GATE
ACCESSORIES
LOOP
DETECTORS
Vehicular Loop Detector Systems
•P
lug-in Detectors (DKS Gate Operators only) and
hard-wired Detectors
• Single and dual channel
re-fabricated loops, 24 ft (7.3 m) circumference
•P
and 50 ft (15.24 m) lead-in
• Pre-fabricated loops available, or form your own loops
Single and Dual Channel
Loop Detector Boards
Loop Test Meter
•M
egohm meter measures loop insulation value up
to 1000 megohms
• Meter range is 20 to 1000 megohms
• Operates on two C batteries
• Includes test leads and vinyl case
Loop Test Meter
Loop Wire
• 18 AWG, XLPE insulation
•A
vailable in 500 and 1000 ft (152.4 and 304.8 m) rolls,
black, blue and red
• Prefabricated loops also available
Loop Wire
­44
Wire Loom
Connector
(Bi-parting gate connection cable)
•C
able provides all the necessary
connections for bi-parting (dual) gate
systems to sequence the primary and
secondary Operators together
Connection Cable
Heater KIT
& Fan Kit
Heater KIT
• Ideal
for Operators installed in cold
weather environments. A built-in
thermostat automatically cycles the
heater on and off as required
Fan Kit
•U
sed with the 1600 Series Barrier
Operators, this fan kit should always be
used when the Operators are installed
in hot/humid environments
Model 1601-093
Fan Kit
Model 1601-154
Heater with Fan
GEAR
Grease
Gear Grease
• 1 4 oz tube of Molybdenum Disulfide (Moly D)
multi-purpose grease keeps the worm gear in
6000 Series Operators lubricated
Apartments & College
Residence Halls
Apartment Complex
& Gated Communities
Commercial
& Industrial
Self
Storage
Parking
Mixed Use
Buildings
Maximum
Security
45
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement