Yamaha MA2030a Owner's manual

Yamaha MA2030a Owner's manual
ZV75780
EN
■ Low-impedance Connections (30W x 2 channels)
Step
3
4
1
POWER AMPLIFIER
Owner’s Manual
First, please carefully read the “IMPORTANT SAFETY INSTRUCTIONS” in the “Technical Specifications.”
Thank you for your purchase of the Yamaha MA2030a/PA2030a power amplifier. This power amplifier was
designed for background music and public address applications in places such as stores, commercial
spaces, and so on. This manual contains installation and setting up information for installers, and
operation instructions for users. Please read through this manual carefully before beginning use, so that
you will be able to take full advantage of the device’s various functions. After you have read the manual,
keep it in a safe place.
• The illustrations as shown in this manual are for instructional purposes only.
• The company names and product names in this manual are the trademarks or registered trademarks of
their respective companies.
• Software may be revised and updated without prior notice.
mark indicates content that is unique to the MA2030a, and
indicates
• In this manual, the
content unique to the PA2030a. Contents that are common to both have no marks.
• Amplifier illustrations are mainly from the MA2030a. Where necessary, illustrations of the PA2030a are
also shown.
Features
• Supports both kinds of speaker connection: high-impedance connection and low-impedance
connection.
• Equipped with digital processor (Feedback Suppressor, Ducker, Leveler).
• Optional PA2030a expansion amplifier enables connection of additional speakers.
Included items
1
2
3
[SETUP] DIP switch
Option
1
1
In a low-impedance installation, if speakers are
placed in a stereo arrangement, set to stereo
output.
6
[SETUP] DIP switch
High-impedance
connections
Yamaha VXC series (ceiling-type)
—
*1: When stereo audio is output, the left channel signal
is output from the [SPEAKERS A] terminals and the
right channel signal is output from the [SPEAKERS B]
terminals.
2
2
Rear panel
3
Speaker expansion
Option
3
To AC outlet
4
Control Panel
(DCP1V4S-US/EU)
Volume adjustment
Step
1
Connecting Speakers
Change the setting depending on the speaker connection (high- or low-impedance connection), the kind
of speakers, and the installation location of the speakers. Refer to “Connecting Speaker Cables” at the
right bottom on this page and the explanation of high-impedance connection, etc. at the following URL.
RCA type
mini-stereo
type
RCA type
Switch 3
Switch 4
0
—
—
—
—
1
Stereo 1
Stereo 2
Stereo 3
Mic. 1/2
Press and hold the [ST SOURCE] knob until the [ST SOURCE] indicator flashes.
2
Mic. 1
Mic. 2
Mic. 1
Mic. 2
Rotate the [ST SOURCE] knob to the left until the volume decreases to the point that
lowers as loud as that of the faintest sounding stereo input (or microphones).
3
Mic. 1
Mic. 2
Mic. 1
Mic. 2
As the volume becomes fainter, the flashing rate of the [ST SOURCE] indicator becomes slower.
4
Mic. 1
—
Mic. 1
—
Push the [ST SOURCE] knob to complete the adjustment.
5
Mic. 2
—
Mic. 2
—
Select the stereo input with the loudest sound by rotating the [ST SOURCE] knob.
The [ST SOURCE] indicator lights.
1
1
Using Microphones
1
Phone
1
2
Euroblock
In case of high-impedance connection, the [SPEAKERS A]
not used. Do not connect to the terminals.
terminal to the positive “+”
terminal to the negative “-”
and [SPEAKERS B]
terminals are
Note In high-impedance settings, the speaker output is processed through a high pass filter (80Hz, 18dB/oct.).
—
—
7
Mic. 1
Mic. 2
—
—
Connecting Speaker Cables
2
3, 4
NOTICE
Ensure that load is not applied to the speaker cable.
When using a spade lug
MA2030a front panel
MA2030a rear panel
PA2030a rear panel
2
3
Note Refer to “Attaching Euroblock Plugs” for Euroblock plug installation.
1
2
Make sure that this device and all devices to be connected are turned off.
4
Connect this device and any external devices with appropriate cables.
Leveler (suppressing wide playback volume variations)
[SETUP] DIP switch 7
[SETUP] DIP switch
7
Leveler disabled
The Leveler function automatically suppresses and corrects for large changes in
Leveler enabled
the playback volume from external devices for a more consistent sound, such as
when reproducing BGM (background music).
Step
3
Connecting Power Cord and Turning On
1, 5
3 AC IN connector
Power cord
When using a bare conductor
4
MA2030a front panel
1
2
3
4
5
MA2030a rear panel
Turn the [MIC IN 1] knob or the [MIC IN 2 GAIN] trimmer all the way to the left, and
connect a microphone to the [MIC IN 1] jack or the [MIC IN 2] connector.
* Actual size
15mm*
(0.6")
≥3.2mm
(≥ 0.13")
Wire
should not
touch the
chassis.
Set the [VOLUME] knob to roughly a 2:00 position.
Loudly speak into the microphone, and turn the [MIC IN 1] knob or the [MIC IN 2 GAIN]
trimmer to the right until the output signal is not distorted.
If you input a loud voice but the output is small, raise the volume with the [VOLUME] knob.
If the sound out of the speakers is too loud, lower the volume with the [MIC IN 1] knob or the [MIC IN 2
GAIN] trimmer.
Make sure the input from external devices matches the volume levels of the
microphones and the external devices.
Refer to “Matching the volume levels of external devices (including microphones)” in “Step 4 Adjusting
Volume” for instructions.
Note • To adjust the [MIC IN 2 GAIN] trimmer, use a slotted screw driver.
• Refer to “Attaching Euroblock Plugs” for installation of Euroblock plugs.
• The input signal is always processed through a high pass filter (120Hz, 12dB/oct.) to cut off low frequency signals
as well as a Feedback Suppressor to suppress howling.
Speaker cable
Attaching Euroblock Plugs
1
Loosen
Jack/connector
[SETUP] DIP switch
[MIC IN 1]
3
Ducker disabled
Option
2
[MIC IN 2]
4
Note • If both Duckers of the [MIC IN 1] jack and the [MIC
IN 2] jack are enabled, the Ducker for the [MIC IN
1] takes priority.
• Activating the Ducker lowers the output volume of
the stereo inputs by 24dB and mutes that of the
other microphone input.
RCA
Turn the [VOLUME] knob all the way to the left.
Connect the supplied power cord to the AC IN connector.
Insert the power cord plug into an appropriate outlet.
MA2030a rear panel
PA2030a rear panel
Connecting the MA2030a and PA2030a lets you increase the number of driven speakers. Connect the [LINE
OUT] jacks of MA2030a and the [LINE IN] jacks of PA2030a.
3
Approx. 5 mm
(approx. 0.2")
4
Tighten
Terminal
screw
Euroblock plug
Note • You must use the supplied Euroblock plugs. If the plugs have been lost, please contact your Yamaha dealer.
Expanding Speakers
RCA
2
Slotted
screwdriver
Ducker (lowering the volume of the other channels automatically when a
microphone signal is input)
[SETUP] DIP switch 3/4
Make sure power switches of this device and devices connected to this device are
position).
turned off (in
After turning on the connected devices (portable audio players, CD players, etc.), turn
on this device.
Loosen the screw, wrap the conductor wire around
the barrier strip terminal, and tighten the screw. Be
sure that the bare wire does not touch the chassis.
≤5.8mm
(≤0.23")
MA2030a rear panel
Ducker enabled
• When turning the system off, turn off this device, and then connected devices.
Use speaker cables to connect the [SPEAKERS A]
terminals of the speakers, and the [SPEAKERS B]
terminals.
Mic. 2
The [SPEAKERS] output connectors on the rear panel are barrier strip type connectors. The connections
are described below for two methods: using a spade lug and using a bare conductor.
Note • Before turning on the power, please check that there are no problems with the cabling, connections, and so on.
Set the speaker output to high-impedance by setting the [OUTPUT] switch to
[100V] or [70V] corresponding to the maximum output voltage.
Mic. 1
Note Refer to “DCP1V4S-US/DCP1V4S-EU Owner’s Manual” for DCP1V4S-US/EU installation.
XLR
NOTICE
Maximum output
voltage: 70V
6
Volume: Adjusts the volume output
to the [SPEAKERS] terminals and
the [LINE OUT] jacks.
Stereo 1/2/3: Switches to stereo
input 1/2/3.
Mic. 1/2: Turns on/off microphone
input 1/2. When a microphone
is on, the switch indicator of the
control panel lights and the stereo
input is muted.
• If the panel ID is set to 3, the
stereo input is not muted even
though the microphone is on.
• If the panel ID is set to 7, the
microphone stays on while
holding the switch.
: A chime sounds when the
microphone is turned on/off
—: Does not work. (No function is
assigned.)
the phase will be reversed and the sound will not be output correctly.
To AC outlet
Maximum output
voltage: 100V
Knob
Volume
Euroblock
CAUTION
1
DIP switch
1 2 3 4
Panel
ID
Switch 2
3, 4
• Before connecting speakers, make sure that the power of the device is turned off. If the power is on, there is a risk of
electrical shock.
2
4
The functions of the knob and the switches of DCP1V4S-US/EU can be configured with DIP switches at
the back of DCP1V4S-US/EU.
Loosen the screw, insert the spade lug all the
way from below, and tighten the screw.
2
■ High-impedance Connections (60W x 1 channel)
3
Sets the panel ID
Note Connect the cables so that the amplifier’s “+” and “-” symbols match those of the speaker. If they are reversed,
Yamaha Pro Audio site: “Better Sound for Commercial Installations”:
http://www.yamahaproaudio.com/global/en/training_support/better_sound/
• Match the impedance settings of this device and the connected speakers. Use in which the impedance does not
match may cause damage to the device or speakers.
• Ensure that load is not applied to the speaker cable.
• In a high-impedance installation, make sure that the sum of the power input ratings of the speakers to be connected
does not exceed 60W.
• In a low-impedance installation, make sure that the total impedance of speakers to be connected is at least 3 ohms.
• Connectable cable gauges: AWG20 (0.5mm2) to AWG16 (1.3mm2)
2
Switch 1
Connecting External Devices
Connect a BGM (background music) tuner, a CD player, a portable audio player, etc. to the stereo input jacks
of this device.
CD players, tuners, etc.
Step
Make sure that the [VOLUME SIGNAL] indicator lights according to the sound input and that sound
comes from the speakers.
Option
1
2
Ethernet CAT5e or more
Straight cable
(800m or less (24AWG))
Input audio signal from the external device, and rotate the [VOLUME] knob.
MA2030a front panel
Option
1
MA2030a rear panel
Microphones
Portable audio player,
etc.
Step
The [ST SOURCE] indicator corresponding to the selected input signal lights.
Mono output
Stereo output (*1)
When connecting to MA2030a,
set the DIP switch 4 to ON
(termination setting).
ON
Select a stereo input by rotating the [ST SOURCE] knob.
Note Adjustable range: -18dB – 0dB, -9dB as the default setting
Mono output
Front panel
Step
Rear panel
When connecting two or more external devices, you can lower the volume of the louder devices (or
microphones) to match the level of the faintest device. If you are using microphones, follow the instructions
in “Option 1 Using Microphones” to adjust the volume level of microphones before executing the operation
below.
4
—: Setting is not required. (Either up or down can be used.)
2
Yamaha Digital Control Panel
DCP1V4S-US/EU
(maximum: one unit)
PA2030a front panel
Matching the volume levels of external devices (including microphones)
8
Low-impedance
connections
High-pass filter (150Hz)
2
1
2
3
Setting mono/stereo output
[SETUP] DIP switch 8
For information on the speaker output settings of the
PA2030a, refer to “Controls and functions.”
Speakers
Step
5
Connecting Yamaha Digital Control Panel DCP1V4S-US/EU to MA2030a enables you to control the
volume, to switch inputs, etc. remotely.
2
MA2030a front panel
terminals to the “+”/“-” terminals of the first
/ terminals to the “+”/“-” terminals of the second
Yamaha VXS series (surface mount-type)
Step
1
4Ω to less than 8Ω
Set the [SETUP] DIP switch 1/2 corresponding to the specifications of the speakers to
be connected.
Setting the [SETUP] DIP switches optimizes the
output signal to match Yamaha VXS/VXC speakers
designed for commercial installations.
Operating with Control Panel
8Ω or more
Set the speaker output to low-impedance connection by setting the [OUTPUT] switch
to [8Ω/4Ω/3Ω].
Connecting Yamaha Speakers
[SETUP] DIP switch 5/6
3
2
■ Configuration of Speaker Output Signal
Setup
Step
1
3Ω to less than 4Ω
Off
• Power cord (2.0m)
• Euroblock plugs (3-pin, 3.50mm pitch) x 1
,x2
• Technical Specifications: includes block diagram, dimensions, and input/output
specifications.
• Owner’s Manual (this sheet)
[SETUP] DIP switch
Speaker
impedance
Connect the [SPEAKERS A] /
speaker, and the [SPEAKERS B]
speaker.
Option
RJ-45
2
1
Adjusting Volume
1
2
3
4
• Recommended cable gauges for the Euroblock plug: AWG26 (0.13mm2) to AWG16 (1.3mm2)
• To prepare the cable for attachment to a Euroblock connector, strip the wire as shown in the illustration using
stranded wire to make connections. With a Euroblock connection, stranded wires may be prone to breakage
because of metal fatigue due to the weight of the cable or due to vibration. When rack mounting your device,
use a lacing bar when possible to bundle and fasten the cables.
• Do not tin (solder) the exposed end.
Loosen terminal screws.
Insert cables.
Securely tighten terminal screws.
Insert the Euroblock plug into the [MIC IN 2] terminal of MA2030a or the [LINE IN]
terminal of PA2030a.
Switching the panel lock on/off
Changes by several knobs can be locked, so that the settings of the device are not affected by accidental
touch or unauthorized operation. The [ST SOURCE], [SOURCE EQ BASS] and [SOURCE EQ TREBLE]
knobs can be locked.
1
2
3
Adjust the [ST SOURCE], [SOURCE EQ BASS] and [SOURCE EQ TREBLE] knobs
to the desired fixed settings.
Press the [ST SOURCE] knob three times within a second.
To set the panel lock off, press the [ST SOURCE] knob three times within a second
again.
Troubleshooting
Controls and Connectors
Front panel
4[VOLUME SIGNAL] indicator
Lights when signal output to speakers exceeds a
certain level.
MA2030a (PA2030a has only 4 and 6)
Low-impedance
connections
[VOLUME LIMIT] indicator
Signal level for which each indicator turns on
Setting
[VOLUME SIGNAL]
[3Ω]
-18.2 dBu or more
[4Ω]
-17.0 dBu or more
Lights if signal output to the speakers exceeds
[8Ω]
-14.0 dBu or more
the limit value, causing the limiter to activate, or if
[70V]
-0.8 dBu or more
High-impedance
the internal temperature of the device increases
connections
[100V]
2.2 dBu or more
abnormally. If the limiter activates, turn the
[VOLUME] knob to the left so the indicator light
goes out. If the device internal temperature increases, leave the device without turning on the power until the internal
temperature goes down.
Symptom
2
3
4
5
6
The power cord is disconnected.
The protection function of the device has been
activated.
No sound is heard.
The sound is lowered too much with the
[VOLUME] knob.
No audio signal is being input.
The input is not selected.
Adjusts the volume output to the speakers. Turning to the right increases the volume. Turning all the way to the left mutes
the sound.
Combo input jack that accepts both phone-type and XLR-type. Connect dynamic microphones mainly. Input signal
is always processed through high pass filter (120Hz, 12dB/oct.) to cut off low frequency signal and Feedback
Suppressor to suppress howling.
[MIC IN 1 SIGNAL] indicator
Lights when signal is input to the [MIC IN 1] jack.
[MIC IN 1] knob
Adjusts the volume of the microphone connected to the [MIC IN 1] jack. Turning to the right increases the volume.
2[ST IN 1] jack
Adjust the volume of the low frequency (around 125Hz) stereo signal from -10dB to +10dB. At the center position, the sound
is flat; turning to the left lowers the low frequency signal and turning to the right increases the low frequency signal. Turning to
the right 90 degrees or more from the center activates the Enhancer to further emphasize the low frequency signal.
[SOURCE EQ TREBLE] knob
Adjust the volume of the high frequency (6 kHz or more) stereo signal from -10dB to +10dB. At the center position, the sound
is flat; turning to the left lowers the high frequency signal and turning to the right increases the high frequency signal. Turning
to the right 90 degrees or more from the center activates the Enhancer to further emphasize the high frequency signal.
Note If the sound distorts when using EQ, turn the knob to the left until the sound is not distorted or lower the volume of the
stereo source.
6Power indicator
Input jack of mini-stereo type (unbalanced input).
Connect a stereo audio source such as portable audio players.
Turns on when the power is on.
If flashing continues for 10 seconds or more, the internal temperature of the device is extremely high. Turn off the power
once, and turn on again several minutes later.
3[ST SOURCE] indicator 1/2/3
Selecting input signal from the [ST IN 1] jack lights indicator 1, the [ST IN 2] jacks lights indicator 2, and the [ST IN 3]
jacks lights indicator 3.
[ST SOURCE] knob
Rotating this switches among the stereo input signals.
Pressing and holding this lets you adjust the volume balance of stereo inputs.
Refer to “Matching the volume levels of external devices (including microphones)” in “Step 4 Adjusting Volume” for
instructions.
The connected microphone is a condenser type.
The sound distorts.
5[SOURCE EQ BASS] knob
1[MIC IN 1] jack
The setting does not
change even when
turning a knob.
The sound is weak.
The sound drops out
and the power indicator
flashes three times.
Turn on/off the power.
WARNING
CAUTION
The power indicator
continues flashing. The
sound goes off.
• Even when the switch is in the off position, a small amount of electricity is still flowing to the unit. If it will not be used for an
extended period of time, therefore, be sure to unplug the power cord from the wall AC outlet.
Note Do not turn off the power switch three seconds or less after executing an operation. If you do, some setting information may
not be saved.
The input level from microphones or external
devices is too high.
The EQ level is too high.
Power switch
• To ensure that high-volume noise is not output from the speakers, power on the connected device first and then turn on this
device. When turning the system off, turn off this device, and then the connected devices.
• After turning the power switch off, wait for about five seconds before turning it on again. Rapidly turning the power switch on
and off in succession can cause the unit to malfunction.
Solution
The power does not
turn on.
[VOLUME] knob
1
Cause
Specifications (MA2030a/PA2030a)
The panel is locked. When the panel is locked,
even when turning the [ST SOURCE] knob,
[SOURCE EQ BASS] knob or [SOURCE EQ
TREBLE] knob, the setting of the device does
not change.
The device is set to low-impedance connection;
however, speakers with high-impedance input
have been connected.
The device is set to high-impedance connection;
however, speakers with low-impedance input
have been connected or too many speakers are
connected.
When the device is set to low-impedance
connection, the total impedance of the
connected speakers is less than the impedance
setting of this device.
The speaker cable is shorted.
The internal temperature of the device is
extremely high because heat dissipation slits are
covered or the device is placed in a confined
place with poor ventilation.
The device settings do not match speaker
impedance.
Connect the power cord.
Turn off the power switch and make sure the
connection is secure. Wait several minutes, and then
turn on the power again.
Turn the [VOLUME] knob to the right.
Make sure that this device is properly connected to
external devices.
Make sure that the external device outputs audio
signal.
Turn the [ST SOURCE] to select input jacks connected
to an external device.
Use a dynamic type microphone or supply phantom
power to the condenser microphone.
Turn the [MIC IN 1] knob/the [MIC IN 2 GAIN] trimmer
to the left to lower the volume of the microphones.
Lower the input volume from the external devices.
Turn the [SOURCE EQ BASS]/[SOURCE EQ TREBLE]
knob to the left to lower the EQ.
Set the panel lock to off. (Press the [ST SOURCE]
knob three times within a second.)
Crosstalk
(MA2030a only)
Match the impedance settings of this device and the
connected speakers.
Match the impedance setting and the input rating
setting of this device and the speakers.
Match the impedance settings of this device and the
speakers.
Inspect the connection of the speaker cables.
Turn off the power, leave the device at a well-ventilated
place, and turn on the device several minutes later.
30 W x 2 ch
60 W x 1 ch
Class D
≤ 0.1%
≤ 0.2%
0 dB, -2.5 dB, +1.0 dB
0 dB, -3.0 dB, +1.0 dB
0 dB, -3.0 dB, +1.0 dB
≤ -70 dB
Stereo in to other Stereo in
100 V/120 V/230 V-240 V,
50 Hz/60 Hz
AC Power Requirement
Power Consumption
(3Ω, AC 100 V)
1/8 max. power,
pink noise at all channel,
Idle
30 W
25 W
0°C–+40°C
-20°C–+60°C
215 x 54 x 288 mm
(8.5 x 2.1 x 11.4 inch)
1.8 kg
(4.0 lbs)
Rack-mount Accessory RKH1
Digital Control Panel DCP1V4S-US/EU
Operating Temperature
Storage Temperature
(W x H x D, including knob)
Net Weight
Optional Accessories
* The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual,
access the Yamaha website then download the manual file.
European Models
Purchaser/User Information specified in EN55103-2:2009.
Conforms to Environments: E1, E2, E3 and E4
Match the impedance settings of this device and the
connected speakers.
• Refer also to the Yamaha Pro Audio website that provides a FAQ (a list of frequently asked questions, with answers).
http://www.yamahaproaudio.com/
• If taking the above steps does not solve the problem, contact your Yamaha dealer for repair.
PA2030a
PLEASE READ CAREFULLY BEFORE
PROCEEDING
Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid
the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These
precautions include, but are not limited to, the following:
Power supply/power cord
7
8 9
0
A
B
C
7
D
7AC IN connector
5
CAUTION
6
0
E
7
Setting
Off
• When connecting the power cord, connect the power cord to the connector and then plug it into an appropriate AC power
outlet.
• Before connecting or disconnecting the power cord, make sure that the power to the device is turned off.
High pass filter 150Hz
Low pass filter 150Hz
8[SPEAKERS] output terminals
Barrier strip type speaker output connectors. Refer to “Connecting Speaker Cables” for the installation instructions.
Low pass filter 200Hz
9[OUTPUT] switch
Frequency correction tailored for Yamaha VXS series (Surface mount-type) speakers
Sets the output type of amplifier: high-impedance connection ([100V], [70V]) or low-impedance connection
([8Ω/4Ω/3Ω]). The setting change will be reflected after turning on again.
Frequency correction tailored for the Yamaha VXS10S/VXS10ST subwoofer (45–150Hz)
0[SETUP] DIP switches
Frequency correction tailored for Yamaha VXC series (Ceiling-type) speakers
Set the following functions of the device. The setting change will be applied after carrying out a power cycle by the
Power switch on the front panel.
DIP switches 1/2: Speaker impedance setting
Sets the speaker impedance if the [OUTPUT] switch is set to [8Ω/4Ω/3Ω] (low-impedance connection).
2
8 9
DIP switches 5/6/7: Speaker EQ
Connect the supplied power cord.
Setting
8Ω or more
DIP switch 7: Leveler
Use the Leveler function to automatically adjust the volume to a relatively constant range if the input signals vary
significantly in volume.
7
Setting
Off
4Ω to less than 8Ω
On
3Ω to less than 4Ω
DIP switches 3/4: Ducker
Configure the settings for the Ducker function. This can mute the microphone input of other channels, and lower the
volume of line input when signals are input to [MIC IN 1] or [MIC IN 2].
4
Setting
Ducker off
Ducker on when signals are input to [MIC IN 2].
Ducker on when signals are input to [MIC IN 1].
Ducker on when signals are input to [MIC IN 1] or [MIC IN 2]. If signals are input to both of them,
[MIC IN 1] is given precedence.
DIP switch 8: Mixer
In low-impedance installation of speakers, this sets the speaker output to stereo or mono.
8
Setting
MONO
STEREO
Note • When the device is shipped from the factory, the DIP switches are all in the up position.
• The output of the [LINE OUT] jacks does not reflect the stereo/mono setting in [SETUP] DIP switch 8 (MIXER).
A[DCP] connector
Connect one Yamaha Digital Control Panel DCP1V4S-US/EU. Refer to “Option 3 Operating with Control Panel” for
connection method.
B[LINE OUT] jacks
DIP switches 5/6: Speaker EQ
Sets the speaker EQ that corrects the output signal to match the type of speakers that are connected.
5
Frequency Response
8Ω/4Ω/3Ω
70 V/100 V
(Output circuitry)
Stereo in à Speaker out,
1 kHz, 15 W, 8Ω/4Ω/3Ω
Stereo in à Speaker out,
1 kHz, 30 W, 70 V/100 V
Line in à Line out,
20 Hz–20 kHz
Line in à Speaker out,
50 Hz–20 kHz, 1 W, 8Ω/4Ω/3Ω
Line in à Speaker out,
90 Hz–20 kHz, 1 W, 70 V/100 V
PRECAUTIONS
MA2030a
3
THD+N
Dimensions
Rear panel
1
Output Power
(20 msec burst, THD+N=1%)
Amplifier Type
6
Setting
Off
High pass filter 150Hz
Frequency correction tailored for Yamaha VXS series (Surface mount-type) speakers
Frequency correction tailored for Yamaha VXC series (Ceiling-type) speakers
RCA type stereo output jack (unbalanced output). Outputs to the [LINE IN] jacks of PA2030a and line input jacks of other
external devices. Outputs a mixed signal of the selected stereo input, the [MIC IN 1] jack input and the [MIC IN 2] jack input.
C[ST IN 2] jacks/[ST IN 3] jacks
RCA type stereo input jack (unbalanced output). Connect external devices such as CD player, etc. Select input jacks with
the [ST SOURCE] knob on the front panel.
D[MIC IN 2] connector
Euroblock 3-pin connector for microphone audio input (balanced). Refer to “Attaching Euroblock Plugs” for Euroblock
plug installation. The input signal is always processed through a high pass filter (120Hz, 12dB/oct.) to cut off low
frequency signals as well as a Feedback Suppressor to suppress howling.
[MIC IN 2 GAIN] trimmer
Adjust the volume of microphone that is connected to the [MIC IN 2] connector. Adjust with a slotted driver of the correct size.
E[LINE IN] jacks/connectors
RCA type and Euroblock 3-pin stereo input jacks/connectors (RCA: unbalanced; Euroblock 3-pin: balanced). Connect to
the [LINE OUT] jacks of the MA2030a or output jacks of other external devices. The signals input from the RCA type jacks
and Euroblock connector will be mixed to the output.
•Do not place the power cord near heat sources such as heaters
or radiators, and do not excessively bend or otherwise damage
the cord, place heavy objects on it, or place it in a position
where anyone could walk on, trip over, or roll anything over it.
• Only use the voltage specified as correct for the device. The
required voltage is printed on the name plate of the device.
•Use only the supplied power cord. If you intend to use the
device in an area other than in the one you purchased, the
included power cord may not be compatible. Please check
with your Yamaha dealer.
• Check the electric plug periodically and remove any dirt or
dust which may have accumulated on it.
•When setting up the device, make sure that the AC outlet you
are using is easily accessible. If some trouble or malfunction
occurs, immediately turn off the power switch and disconnect
the plug from the outlet. Even when the power switch is turned
off, as long as the power cord is not unplugged from the wall
AC outlet, the device will not be disconnected from the power
source.
•Remove the electric plug from the outlet when the device is not
to be used for extended periods of time, or during electrical
storms.
•Be sure to connect to an appropriate outlet with a protective
grounding connection.
Do not open
•This device contains no user-serviceable parts. Do not
open the device or attempt to disassemble the internal
parts or modify them in any way. If it should appear to be
malfunctioning, discontinue use immediately and have it
inspected by qualified Yamaha service personnel.
Water warning
• Do not expose the device to rain, use it near water or in damp
or wet conditions, or place on it any containers (such as vases,
bottles or glasses) containing liquids which might spill into any
openings. If any liquid such as water seeps into the device,
turn off the power immediately and unplug the power cord from
the AC outlet. Then have the device inspected by qualified
Yamaha service personnel.
•Never insert or remove an electric plug with wet hands.
Hearing loss
•Avoid setting volume controls to their maximum. Depending on
the condition of the connected devices, doing so may result
in feedback that can cause hearing loss and damage the
speakers.
•Do not use speakers for a long period of time at a high or
uncomfortable volume level, since this can cause permanent
hearing loss. If you experience any hearing loss or ringing in
the ears, consult a physician.
• When turning on the AC power in your audio system, always
turn on the device LAST, to avoid hearing loss and speaker
damage. When turning the power off, the device should be
turned off FIRST for the same reason.
Fire warning
• Do not place any burning items or open flames near the
device, since they may cause a fire.
If you notice any abnormality
• If any of the following problems occur, immediately turn off the
power switch and disconnect the electric plug from the outlet.
– The power cord or plug becomes frayed or damaged.
– Unusual smells or smoke are emitted.
– Some object has been dropped into the device.
– There is a sudden loss of sound during use of the device.
– Cracks or other visible damage appear on the device.
Then have the device inspected or repaired by qualified
Yamaha service personnel.
• If this device should be dropped or damaged, immediately turn off
the power switch, disconnect the electric plug from the outlet, and
have the device inspected by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the
possibility of physical injury to you or others, or damage to
the device or other property. These precautions include, but
are not limited to, the following:
Power supply/power cord
•When removing the electric plug from the device or an outlet,
always hold the plug itself and not the cord. Pulling by the cord
can damage it.
Location
•Do not place the device in an unstable position where it might
accidentally fall over.
• Do not block the vents. This device has ventilation holes at the top/
sides/bottom to prevent the internal temperature from becoming
too high. In particular, do not place the device on its side or
upside down. Inadequate ventilation can result in overheating,
possibly causing damage to the device(s), or even fire.
•When installing the device and you wish to dissipate heat on it:
–– Do not cover it with any cloth.
–– Do not install it on a carpet or rug.
–– Make sure the top surface faces up; do not install on its
sides or upside down.
–– Do not use the device in a confined, poorly-ventilated
location.
Inadequate ventilation can result in overheating, possibly
causing damage to the device(s), or even fire.
If this device is to be used in a small space other than EIAstandard rack, make sure that there is adequate space around
the device: at least 10 cm above, 1 cm below the bottom
surface, 10 cm at the sides and 10 cm behind.
•Do not place the device in a location where it may come into
contact with corrosive gases or salt air. Doing so may result in
malfunction.
•Before moving the device, remove all connected cables.
•If the device is mounted in an EIA standard rack, carefully
read the section “Precautions for rack mounting”. Inadequate
ventilation can result in overheating, possibly causing damage
to the device(s), malfunction, or even fire.
NOTICE
Connectors
To avoid the possibility of malfunction/ damage to the product,
or damage to other property, follow the notices below.
XLR-type connectors are wired as follows (IEC60268
standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).
Handling and maintenance
Precautions for rack mounting
•Do not use the device in the vicinity of a TV, radio, stereo
equipment, mobile phone, or other electric devices.
Otherwise, the device, TV, or radio may generate noise.
•Do not expose the device to excessive dust or vibration,
or extreme cold or heat (such as in direct sunlight, near a
heater, or in a car during the day), in order to prevent the
possibility of panel disfiguration, unstable operation, or
damage to the internal components.
•Do not place vinyl, plastic or rubber objects on/under the
device, since this might discolor the panel of the device or
the objects placed on/under the device.
•Keep input cables of microphone, etc., devices that contain
sensitive circuits, and the power cord at a distance from
speaker cables and fasten the speaker cables in place.
Since a large amount of current can flow in a speaker cable,
a magnetic field will be generated and may produce radio
interference and acoustic noise.
•When cleaning the device, use a dry and soft cloth. Do not
use paint thinners, solvents, cleaning fluids, or chemicalimpregnated wiping cloths.
•Condensation can occur in the device due to rapid, drastic
changes in ambient temperature–when the device is moved
from one location to another, or air conditioning is turned
on or off, for example. Using the device while condensation
is present can cause damage. If there is reason to believe
that condensation might have occurred, leave the device
for several hours without turning on the power until the
condensation has completely dried out.
•Do not use this device for any purpose other than driving
loudspeakers.
•If you put the device on a table or a rack, do not remove the
rubber feet from the device.
•Always turn the power off when the device is not in use.
This unit is rated for operation at ambient temperatures
ranging from 0 to 40 degrees Celsius. If the device is mounted
with other devices in an EIA standard equipment rack, internal
temperatures can exceed the specified upper limit, resulting
in impaired performance or failure. If the device is mounted
in a rack, always observe the following requirements to avoid
heat buildup:
•If the device is mounted in a rack with other devices that
generate a significant amount of heat, such as a power
amplifier, leave more than 1U of space between the device
and other devices (both above and below). Also, make
sure to either leave any open spaces uncovered or install
appropriate ventilating panels to minimize the possibility of
heat buildup.
•To ensure sufficient airflow, leave the rear of the rack open
and position it at least 10 centimeters from walls or other
surfaces. If you’ve installed a fan kit, there may be cases
in which closing the rear of the rack will produce a greater
cooling effect. Refer to the rack and fan unit manual for
details.
Connections
•Before connecting the device to other devices, turn off the
power for all devices. Also, before turning the power of all
devices on or off, make sure that all volume levels are set to
the minimum. Failing to do so may result in electric shock, or
equipment damage.
•Use only speaker cables for connecting speakers to the
speaker jacks. Use of other types of cables may result in fire.
Information for users on collection and disposal of old equipment:
This symbol on the products, packaging, and/or accompanying documents means that used electrical and
electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points,
in accordance with your national legislation.
Maintenance
By disposing of these products correctly, you will help to save valuable resources and prevent any potential
negative effects on human health and the environment which could otherwise arise from inappropriate waste
handling.
•Remove the power plug from the AC outlet when cleaning the
device.
Handling caution
For more information about collection and recycling of old products, please contact your local municipality,
your waste disposal service or the point of sale where you purchased the items.
•When the surface of the device heats up, do not touch it until
the panel temperature goes down. Touching the surface with
its high temperature may cause burns.
•Avoid inserting or dropping foreign objects (paper, plastic,
metal, etc.) into any gaps or openings on the device (vents,
etc.) If this happens, turn off the power immediately and
unplug the power cord from the AC outlet. Then have the
device inspected by qualified Yamaha service personnel.
•Do not rest your weight on the device or place heavy objects
on it. Avoid applying excessive force to the buttons, switches
or connectors.
•Avoid pulling the connected cables to prevent injuries or
damage to the device.
Yamaha cannot be held responsible for damage caused by
improper use or modifications to the device.
For business users in the European Union:
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further
information.
Information on Disposal in other Countries outside the European Union:
This symbol is only valid in the European Union. If you wish to discard these items, please contact your local
authorities or dealer and ask for the correct method of disposal.
(weee_eu_en_02)
The model number, serial number, power requirements,
etc., may be found on or near the name plate, which is at
the bottom of the unit. You should note this serial number
in the space provided below and retain this manual as a
permanent record of your purchase to aid identification in
the event of theft.
Yamaha Eco-Label
Yamaha Eco-Label is a mark that
certifies products of high environmental
performance.
Model No.
Serial No.
(bottom_en_01)
Yamaha Pro Audio global website
http://www.yamahaproaudio.com/
Yamaha Downloads
http://download.yamaha.com/
Manual Development Group
© 2016 Yamaha Corporation
Published 10/2016 KSHD-A0
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement