FireHawk® M7 Air Mask - LaFrance Equipment Corporation

FireHawk® M7 Air Mask - LaFrance Equipment Corporation
Self-Contained Breathing Apparatus
FireHawk® M7 Air Mask
MSA’s new FireHawk M7 Air Mask
represents a true technological
achievement in critical personal
protection. As firefighters determined
the safety requirements that
would be needed to meet the new
NFPA 1981 and 1982–2007-edition
standards, MSA’s engineering teams
began designing the solutions.
The new FireHawk M7 Air Mask
emerged with seven life-safety design
components built on a modular Air Mask
platform, developed to exceed the new
NFPA 2007 requirements and provide
firefighters with the highest-quality
SCBA currently available.
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
41
Self-Contained Breathing Apparatus
FireHawk® M7 Air Mask
1. TAKING THE HEAT
4. FIREGROUND MANAGEMENT
Although MSA PASS alarms have performed in extreme
temperatures for more than a decade, a top priority was to
design an alarm that could really take the heat! The new M7 alarm
(patent pending) was developed in cooperation with prominent
university acoustic experts, resulting in an emitter that exceeds
95 decibels with solid performance at the NFPA 500F test! Once
again, giving you that lifesaving edge in the face of danger.
Firefighter accountability systems have never before been
as practical, complete, and user-friendly as the MSA M7
Accountability System. It’s based on the ICM TxR Unit
introduced in mid-2006, which has thousands of systems
deployed in virtually every type of fire department, and they’re
performing phenomenally! It displays a full array of visual
and audible information for up to 100 firefighters within a
one-mile-line-of-site – exactly what incident commanders
wanted. Record keeping is also made easy by downloading
reports. This crown jewel is available only from MSA!
2. VIRTUALLY “BULLET-PROOF” ELECTRONICS
Like an armor shield, the M7 HUD, Power Module, and
Control Module are encased in a proprietary high-temperature
impact-grade polymer, providing the highest possible protection
against impact and water ingress. Electronics enclosures are
permanently sonically welded to a hermetic standard and use a
high-pressure O-ring to ensure a consistent water-tight seal.
The new M7 electronics are virtually “bullet-proof” against
fire-ground hazards.
3. STRAIGHT-TALK COMMUNICATIONS
We’ve got you covered with communications, starting with a
high-performance mechanical speech diaphragm, with performance
that exceeds the new NFPA requirements as a stand-alone
solution. Backing the mechanical diaphragm is an electronic
amplifier with an internal facepiece microphone for ultimate
clarity. The ClearCommand® Communication System provides
clear communication during the most critical times. This Air Mask
speaks loud and clear when it comes to communications.
42
5. EXTENDED PROTECTION
The new FireHawk M7 Air Mask is not your typical SCBA.
Firefighters need to be prepared for the unexpected, and
emergency egress from a 2nd-floor or higher can be impossible
without the right safety equipment. That's why the new
M7 Air Mask offers an NFPA- compliant integrated rappelling
system, called the Rescue Belt, providing firefighters with one
more lifesaving option in the face of danger.
"Above and beyond" protection is also provided with the
CBRN FireHawk MMR. The CBRN FireHawk includes a
positive-protection Tetraplex™ shield, to prevent contact
between chemical warfare agents and the most vulnerable
component of regulators, their thin elastomeric diaphragm.
Other "air-wash" approaches may pass in laboratory
conditions. The shield provides positive protection against
all potential conditions.
External hazards are bad enough without having concerns of
spreading illness among firefighters through shared-use SCBA.
The Ultra Elite® facepiece protects you against user crosscontamination with MSA’s inhalation check-valve: a “must have” in
modern safety equipment.
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
Self-Contained Breathing Apparatus
6. LIGHTWEIGHT AND EASY TO USE
Firefighters already have enough weight to carry and gear to
maintain, so MSA engineers set out to lighten the load of
components, reduce parts counts, simplify maintenance, maximize user
comfort, and modularize the design. The FireHawk M7 Air Mask has a
lightweight polymer backplate, with quick-release harness straps, an
error-proof cam-lock cylinder attachment, fast change-out electronic
components, a large swiveling lumbar pad, and regulators that will
fit in the palm of your hand (less than 30 parts for the MMR and 14 for
the 1st stage). Our time-tested Ultra Elite facepiece has unbeatable
comfort, visibility, communications, cross-contamination protection,
fit, and seal.
7. PLATFORM FOR THE FUTURE
The FireHawk M7 Air Mask is designed to accept future technology
upgrades. Included in every M7 electronics ensemble is a 2.4GHz
personal wireless network, a network that transmits and receives
encrypted information over a short-range on a firefighter’s body.
This new wireless feature provides the capability to add on future
technology that can provide additional information back to incident
command through the FireHawk M7 Accountability System.
Software can also be upgraded wirelessly in the field, through
the M7 wireless network. You never have to worry about radio
interference either – we have you covered with a thoroughly-tested
RFI shield design that protects against all fireground radio signals.
The new FireHawk M7 Air Mask provides
you with the best technology
today and positions you
for well into the future.
M7 Air Mask
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
43
Self-Contained Breathing Apparatus
How to Order SCBA: Get the Exact Model You Need
The Assemble-To-Order System
MSA’s Assemble-To-Order System (ATO) will make ordering the right mask easier and faster than ever. Instead of choosing from a handful of complete
Air Mask assemblies, users can order a custom-made Air Mask with every option exactly as desired. Contact MSA Customer Service Center for details.
FireHawk M7 Air Mask Ordering Selection Matrix (NFPA 1981 and 1982 - 2007 edition compliant, NIOSH 42 CFR Part 84 CBRN certified)
Air Mask
Pressure
L 2216
M 3000
Carrier/
Harness
Assembly
A Single
Pull
without
chest
strap
Lumbar Pad/
Rescue Belt
0 None
0 None
1 Swiveling
Lumbar Pad
1 3AL Aluminum
with air
A Rescue Belt Standard, 50'
B Single
Pull with B Rescue Belt chest
Mid-Size, 50'
strap
C Rescue Belt C Double
Long, 50'
Pull
D
Rescue Belt without
Standard, 75'
chest
strap
D Double
Pull with
chest
strap
H 4500
Options A
& B can
only be
chosen if a
rescue belt
is selected.
Cylinder
E Rescue Belt Mid-Size, 75'
F Rescue Belt Long, 75'
If choosing a
rescue belt,
the carrier/
harness
assembly
must be a
single pull
(options A
or B).
3 30' Carbon with air
4 3AL Aluminum
less air
6 30' Carbon less air
0 None
1 30+ Carbon
with air
2 30+ Carbon
less air
0 None
1 30' Carbon with air
2 45' Carbon with air
3 45' Carbon
low-profile with air
Emergency
Breathing
Support
Facepiece
0 None
A None
0 None
1 Quick-Fill
B Hycar
Small
1 Medium
MMR Type
A CBRN
Firehawk
STC,
threaded
B CBRN
Firehawk
STC, QC,
C CBRN
Firehawk
PTC,
threaded
D CBRN
Firehawk
PTC, QC
2 ExtendAire
C Hycar
3 Quick-Fill
Medium
and
ExtendAire D Hycar
Large
If choosing an
Air Mask
Pressure M, M is
not compatible
with Quick-Fill.
Nosecup
2 Large
Head
Harness
0 None
Electronic
Communications
Integrated
PASS/Telemetry
A None
A PASS with thermal
alarm activated
2 SpeeD-ON B Clear Command
less neck
Ready with bracket B PASS without
strap
thermal alarm
C Clear Command
activated
4 SpeeD-ON
Amp
with neck
C PASS, telemetry
D Clear Command
strap
and thermal alarm
Amp/RI
D PASS, telemetry
and without
thermal alarm
Case
0 None
1 Hard
Case
2 Soft
Case
If choosing an
ExtendAire
option, the
MMR type
must be a
QC (option
B or C).
4 60' Carbon with air
5 30' Carbon less air
6 45' Carbon less air
7 45' Carbon
low-profile less air
8 60' Carbon less air
Part Number
44
A-M7
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
Self-Contained Breathing Apparatus
FireHawk® M7 Responder Air Mask
MSA’s new FireHawk M7 Responder Air Mask is uniquely versatile
protection that can quickly be transformed into a CBRN air-purifying
respirator (APR) or a CBRN powered air-purifying respirator (PAPR).
You can change respirator modes as your job changes direction from first
response and rescue to scene management and remediation activities.
PAPR
PAPR
Firefighters typically are the first to respond to any incident
whether it is a residential fire, an accident, or any unknown threat.
MSA’s FireHawk M7 Responder Air Mask provides the maximum level of
protection for CBRN environments. However, that amount of protection is
not always needed, especially outside the immediate fire scene. Once the
hazard has been assessed, air-purifying respirators (APR) may make the
most sense for low concentrations of certain contaminants.
The M7 Responder facepiece is NIOSH approved for the SCBA, PAPR and
APR configurations, in accordance with the MSA users instructions. This
practical emergency respiratory protection system meets/ exceeds the
latest requirements of NFPA and NIOSH standards (see ATO ordering
information for details). It’s the first and only of its kind, and an emergency
responder’s dream come true.
APR
The FireHawk M7 Responder Air Mask
The FireHawk M7 Responder PAPR
Based on the seven life-safety design components built on the FireHawk
M7 Air Mask to ensure you of the highest-quality SCBA currently available,
giving you that lifesaving edge in the face of danger. This new air mask
offers more options than any other product in the industry, combined with
the unique CBRN APR and PAPR options.
The CBRN Responder PAPR (Powered Air-Purifying Respirator) system is
ideal when you need non-IDLH respiratory protection for an extended
period of time (up to 8 hours). This PAPR provides an OSHA-assigned
protection factor 20 times greater than APR, due to positive pressure in the
mask. Essentially, it combines an industry-leading motor-blower to the
Ultra Elite M7 Responder Facepiece, and CBRN canisters for up to 8 hours of
air-purifying respiratory protection. Its constant filtered air flow (of at least
115 lpm) improves comfort with a cooling effect, greatly reducing
pulmonary stress, and preserving strength and mental acuity. The airflow
also prevents fogging in the facepiece, reduces claustrophobia,and allows
for extended use in hot and stressful environments.
The FireHawk M7 Responder APR
To convert from SCBA to APR, the canister and breathing tube must be attached to
the facepiece. When the SCBA cylinder valve is closed, facepiece valves convert to
air-purifying mode through the APR canister. Although the air mask carrier and
harness and cylinder may be removed from the user, the MMR regulator must
always be connected to the inlet adapter to seal the facepiece inlet port.
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
45
Self-Contained Breathing Apparatus
How to Order SCBA: Get the Exact Model You Need
The Assemble-To-Order System
MSA’s Assemble-To-Order System (ATO) will make ordering the right mask easier and faster than ever. Instead of choosing from a handful of complete
Air Mask assemblies, users can order a custom-made Air Mask with every option exactly as desired. Contact MSA Customer Service Center for details.
FireHawk M7 Responder Air Mask Ordering Selection Matrix (NFPA 1981 and 1982 - 2007 edition compliant, NIOSH 42 CFR Part 84 CBRN certified)
Carrier/
Harness
Assembly
Air Mask
Pressure
L
2216
A Single Pull
without
chest strap
B Single Pull
with chest
strap
M
H
Lumbar Pad/
Rescue Belt
0 None
0 None
0 None
1 Swiveling
Lumbar Pad
3 30' Carbon with air
1 Quick-Fill
A Rescue Belt Standard, 50'
Options A &
B can only
be chosen
if a rescue
belt is selected.
4500
6
E Rescue Belt - 1
Mid-Size, 75' 2
F Rescue Belt - 3 45' Carbon
Long, 75'
low-profile with air
If choosing a
rescue belt,
the carrier/
harness
assembly
must be a
single pull
(options A
or B).
B Hycar
Small
0 None
Head
Harness
0 None
Electronic
Communications
A None
4 60' Carbon with air
5 30' Carbon less air
6 45' Carbon less air
APR/PAPR
Kits
A None
1 Medium 2 SpeeD-ON B Clear Command
C Hycar
less neck
Ready with
30' Carbon less air 2 ExtendAire
2 Large
Medium
strap
bracket
Quick-Fill
D Hycar
4 SpeeD-ON C Clear Command
3 and
Large
with neck
Amp
None
ExtendAire
strap
D Clear Command
30+ Carbon with air
Amp/RI
If choosing
30+ Carbon less air
an Air Mask
Pressure M,
M is not
None
compatible
30' Carbon with air
with
Quick-Fill.
45' Carbon with air
0
B Rescue Belt C Double Pull
Mid-Size, 50' 1
without
chest strap C Rescue Belt - 2
Long, 50'
D Double Pull
with chest D Rescue Belt strap
Standard, 75' 0
3000
Emergency Facepiece
Breathing and MMR Nosecup
Support Regulator
Cylinder
B APR 18” tube
C APR 22” tube
D APR 18” tube
with PAPR kit
Integrated
PASS/Telemetry
A PASS with
thermal alarm
activated
B PASS without
thermal alarm
activated
Case
0 None
1 Hard
Case
2 Soft
Case
E APR 22” tube C PASS, telemetry
and thermal
with PAPR kit
alarm
D PASS, telemetry
and without
thermal alarm
ExtendAire
options are
currently
unavailable
at this time.
7 45' Carbon
low-profile less air
8 60' Carbon less air
A-M7R
Quantity
Part Number
Special note regarding approvals: approvals are only available (and were obtained) for each component (SCBA, APR and PAPR) as an independent CBRN respirator. Although the APR, PAPR and SCBA have
been evaluated for seamless convertibility in a contaminated environment, as well as to the NFPA heat and flame test criteria, there is currently no standard for which to seek this type of system approval.
Users are advised to convert among modes in an uncontaminated environment. Please see user's instructions for specific approval information and limitations.
Ultra Elite M7 Responder Facepieces
with ClearCommand Bracket
PAPR only
without ClearCommand Bracket
Small
10093927
Small
10093924
Medium
10093926
Medium
10093923
Large
10093928
Large
10093925
46
CBRN Canister
10094024
C420 PAPR Kits (less facepiece and
cartridge), includes C420 PAPR, belt,
air-flow indicator and breathing tube
Accessories for C420 PAPR
Spare/Replacement M7 HUD
M7 Responder HUD
M7 Responder HUD with bracket
10093911
10093912
APR only
10046570
B-20040-001
NiMH Rechargeable Battery Kit
(2 NiMH batteries, charger and cap)
M-20020
LiSO2 Battery
10094021
6” Breathing Hose Assembly
S-20036
NiMH Rechargeable Battery Pack
B-20090-001 NiMH Rapid Battery Charger
10046570
CBRN Canister
B-30060-001 NiMH Rechargeable Battery Cap Assembly
10094016
APR Breathing Tube, 18"
S-30019
10094023
APR Breathing Tube, 22"
B-10079-001 PAPR Carrying Case
Web Belt Assembly
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
Self-Contained Breathing Apparatus
AirHawk® II Industrial Air Mask
New!
Industrial SCBA with enhanced options to fit many budgets.
The new AirHawk II Air Mask is built upon MSA’s established AirHawk MMR Air Mask and is a lightweight, durable, and
economical SCBA for many industrial IDLH (immediately dangerous to life or health) applications. This SCBA fits any budget
by keeping its lower-cost options while offering many new choices not offered with any other industrial air mask. In
addition, the AirHawk II Air Mask is available in both low-pressure and high-pressure versions.
MSA’s AirHawk II Air Mask is a pressure-demand apparatus designed to maintain a slight positive air pressure inside the
facepiece during inhalation and exhalation. Positive pressure helps to prevent contaminants from seeping in and around
the facepiece, even if small breaks in the face-to-facepiece seal should occur. The AirHawk II Air Mask is built from six
major components: facepiece, carrier and harness assembly, cylinder, first-stage regulator, mask-mounted regulator, and
End-of-Service-Time-Indicator (EOSTI).
Facepiece
MSA offers you the choice of two facepieces, the
proven Ultra Elite Facepiece or new industrial
Advantage 4000 Facepiece for the AirHawk II Air
Mask. Choose from three facepiece sizes (small,
medium or large) in either Hycar Rubber or silicone
rubber. Nosecups are available in two sizes,
standard and large.
chest strap, making this unit the most comfortable
industrial air mask on the market today.
The cylinder band is available in nylon or Kevlar
and is secured by an adjustable nylon buckle,
allowing the band to retain various cylinder sizes.
An optional open-form stainless steel cylinder band
provides rapid drop-in cylinder replacement,
eliminating webbing adjustments and clips.
The Ultra Elite Facepiece features:
• a one-way check valve preventing exhaled air
from entering the mask-mounted regulator
• a molded polycarbonate lens
• a mechanical speaking diaphragm for shortrange communications
• five adjustable rubber straps for exceptional
head comfort, security, and safety
• optional heat-resistant Kevlar hairnet-style
head harness
Cylinders
The Advantage 4000 Facepiece features:
• adapters to convert the Advantage Facepiece to a
Twin-Cartridge Respirator (using Advantage
Cartridges) or an RD40 Facepiece
• a one-way check valve preventing exhaled air
from entering the mask-mounted regulator
• a molded polycarbonate lens
• four-point silicone head harness for exceptional
comfort and security
• optional polyester net head harness
The PR-14 Regulator is designed with the fewest
number of parts in the industry, with Teflon- coated
anodized valve bodies to minimize internal
component friction and maximize service life. The
PR-14 Regulator has only 14 replaceable parts and
can be maintained without special tools.
Airframe Carrier and Harness Assembly
MSA’s durable AirFrame Carrier and Harness
assembly comes standard with large side handles
and a central attachment point to pull workers to
safety in rescue scenarios. The AirFrame Carrier and
Harness distributes the SCBA’s weight over the
user’s hips for comfort and stability. The composite
backplate is made of glass fiber-reinforced
thermoset plastic and is ergonomically designed
with a spine strain relief. Key com-ponents are
detachable without special tools.
The assembly’s harness components are available
in nylon or high-strength Kevlar. Shoulder straps
feature easy-to-release friction buckles to positively
retain pull straps. A center-pull waist belt system is
also incorporated into its design. This harness also
provides optional shoulder pads, lumbar pad, and
MSA offers a choice of three low-pressure (2216
psig) 30-minute-rated cylinders for use with this
SCBA. Choose carbon-wrapped, fiberglass hoopwound, or all-aluminum construction cylinders.
High-pressure (4500 psig) carbon-wrapped
cylinders are available in 30-, 45- or 60-minute
durations.
First-Stage Regulator
• Optional wireless Heads-Up Display provides the
user with the remaining volume of cylinder air
through four colored LEDs
• Optional Rapid Intervention Crew (RIC) System
enables quick refilling (less than a minute) of an
SCBA cylinder from a mobile compressor or
cascade system, or you can also transfill between
two SCBA wearers
• Optional Emergency Egress Rescue Belt, integral
to the SCBA waist belt, features a Kevlar line (50
ft. or 75 ft.) and rappelling hardware
• Optional shoulder-mounted Quick-Fill System
EBS accessory offers SCBA cylinder refill from a
mobile compressor or cascade system and also
allows transfilling between two SCBA wearers
• Optional ICM Tx Integrated PASS/HUD
Transmitter features the Personal Alert Safety
System (PASS) and the HUD Transmitter
combined within a single housing
Mask-Mounted Regulator
The second-stage Firehawk Regulator features a
slide-to-connect (S-T-C) or push-to-connect (P-T-C)
regulator attachment to meet the widest
preference ranges. An integrated shut-off prevents
cylinder air loss when disconnecting the secondstage regulator from the facepiece. The FireHawk
Regulator has only 22 replaceable parts and can be
maintained without special tools.
EOSTI
MSA’s Audi-Larm™ Audible Alarm is an air-actuated
continuously-ringing warning bell
that automatically sounds when
the air-supply cylinder reaches
25% of its rated service life.
Options
• Optional air-line port,
designed to accept an
air-line connection from
an independent air source
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
47
Self-Contained Breathing Apparatus
AirHawk® II Industrial Air Mask
AirHawk II SCBA
Comes with nylon harness with chest strap, low pressure (2216 psig)
Facepiece
Cylinder
Hard Case
No Case
Ultra Elite, medium Hycar, rubber head harness
Aluminum - 30 minutes
10095800
10095801
Ultra Elite, medium Hycar, Speed-On head harness
L30 Stealth carbon cylinder (30 minutes)
10095802
10095803
Adv 4000, medium Hycar, net head harness
Aluminum - 30 minutes
10095804
Call
Adv 4000, medium Hycar, rubber head harness
Aluminum - 30 minutes
Call
10095805
Adv 4000, medium Hycar, net head harness
L30 Stealth carbon cylinder (30 minutes)
10095806
10095807
Storage Cabinets
Two unit and single unit wall mounting case. Chemical resistant ABS plastic case resists weathering, moisture,
and corrosion to ensure SCBA stay in ready-to-use condition.
Storage Cabinets
10053102
Double case for SCBA’s supplied with LP30, HP45, HP60 and low profile cylinders
10053103
Double case for SCBA’s supplied with HP30 cylinders only
10052744
Single case for SCBA’s supplied with LP30, HP45, HP60 and low profile cylinders
10052745
Single case for SCBA’s supplied with H30 cylinders only
AirHawk® II Industrial Air Mask Assemble-To-Order (ATO) Matrix
Carrier/Harness
Assembly
SCBA Type
A2L 2216
A AirFrame, Nylon Harness,
AirHawk II
Fabric Band, Plastic Buckle,
Air Mask
Double Pull
B AirFrame, Nylon Harness,
Fabric Band, Plastic Buckle,
Double Pull, W/Chest Strap
C AirFrame, Nylon Harness,
Steel Band, Plastic Buckle,
Double Pull
D AirFrame, Nylon Harness,
Steel Band, Plastic Buckle,
Double Pull, W/Chest Strap
E AirFrame, Kevlar Harness,
Fabric Band, Plastic Buckle,
Double Pull
F AirFrame, Kevlar Harness,
Fabric Band, Plastic Buckle,
Double Pull, W/Chest Strap
G AirFrame, Kevlar Harness,
Steel Band, Plastic Buckle,
Double Pull
H AirFrame, Kevlar Harness,
A2H 4500
Steel Band, Plastic Buckle,
AirHawk II
Double Pull, W/Chest Strap
Air Mask
J AirFrame, Reflective Kevlar
Harness, Steel Band, Metal
Buckle, Single Pull
K AirFrame, Reflective Kevlar
Harness, Steel Band, Metal
Buckle, Double Pull
L AirFrame, Reflective Kevlar
Harness, Steel Band, Metal
Buckle, Single Pull, W/Chest
Strap
M AirFrame, Reflective Kevlar
Harness, Steel Band, Metal
Buckle, Double Pull,
W/Chest Strap
Options J and L can only be
chosen if a rescue belt option
is selected.
Lumbar Pad/
Rescue Belt
0 None
0 None
1 Shoulder Pad
1 3AL Aluminum
2 Standard Lumbar Pad 2 Hoop-Wound
3 Shoulder & Standard
Lumbar Pad
3 30' Carbon
4 3AL Aluminum,
4 Swiveling Lumbar Pad
Less air
5 Shoulder & Swiveling 5 Hoop-Wound,
Lumber Pad
less air
A Rescue Belt, Standard, 6 30' Carbon,
50 Ft. Rope
less air
B Rescue Belt, Standard,
75 Ft. Rope
D Rescue Belt, Long,
75 Ft. Rope
F Rescue Belt,
Swiveling, Standard,
75 Ft. Rope
G Rescue Belt,
Swiveling, Long,
50 Ft. Rope
H Rescue Belt,
Swiveling, Long,
75 Ft. Rope
J Rescue Belt, MidSize, 50 Ft. Rope
K Rescue Belt, MidSize, 75 Ft. Rope
L Rescue Belt,
Swiveling, Mid-Size,
50 Ft. Rope
0 None
5 30' Carbon,
less air
48
Nosecup
Head
Harness
0 None
A None
0 None
B Ultra Elite,
Hycar, Small
B FireHawk
PTC, QC,
solid cover,
2 Hansen
SST
1 Quick-Fill
Shoulder
Mounted
1 Medium 1 Rubber,
less
2 Large
neckstrap
C FireHawk
STC, single
hose, solid
cover
D FireHawk
STC, QC,
solid cover
T FireHawk,
STC,
threaded
hose, solid
cover
FireHawk
slide regulators
not compatible
with Advantage
4000
Facepieces
6 45' Carbon,
less air
7 45' Carbon,
low profile,
less air
3 Hansen
Brass
4 Foster
Steel
2 ExtendAire
(EBS) with
Dual Quick
Connect
3 Shoulder
Mounted
Quick Fill &
5 Snap-Tite
ExtendAire
Locking
(EBS) with
Aluminum
Dual Quick
Connect
6 Foster SST
Cannot use
Air-Line
Option if
Rescue Belt
is chosen.
C Ultra Elite,
Hycar,
Medium
2 Net, less
neckstrap
3 Rubber,
with
neckstrap
D Ultra Elite,
Hycar, Large
E Ultra Elite,
Silicone,
Small
F Ultra Elite,
Silicone,
Medium
G Ultra Elite,
Silicone,
Large
H Advantage
4000, Hycar,
Small
J Advantage
4000, Hycar,
Medium
K Advantage
4000, Hycar,
Large
L Advantage
4000, Silicone.
Small
M Advantage
4000, Silicone.
Medium
N Advantage
4000, Silicone.
Large
0 None
4 Cloth, with
neckstrap
Nosecup
stanard
with
Advantage
4000
Facepiece
Neckstrap
not available
with
Advantage
4000
Facepiece
Communications
A None
B Clear
Command
Ready
C Amp
D Amp, RI
Gauge/
Integrated
PASS
A Pressure
Gauge
B ICM Tx
with Heat
Sensor
C ICM Tx
without
heat
sensor
Case
0 None
1 Hard
Case
2 Soft
Case
Communication
s not compatD ICM TxR
ible with
with heat
Advantage 4000
sensor
Facepiece
E ICM TxR
without
heat
sensor
F Pressure
Guage
with HUD
G ICM TX
with heat
sensor
with HUD
H ICM TX
without
heat
sensor
with HUD
J ICM TxR
with heat
sensor
with HUD
K ICM TxR
without
heat
sensor
with HUD
L HUD Only
8 60' Carbon,
less air
M Rescue Belt,
Swiveling, Mid-Size,
75 Ft. Rope
Note: Standard Rescue Belt fits waist
sizes up to 54 inches. Long Rescue
Belt fits waist sizes up to 74 inches.
NIOSH Approved,
Non NFPA Compliant
Facepiece
1 Snap-Tite,
Aluminum
2 45' Carbon
4 60' Carbon
Emergency
Breathing
System
0 None
1 30' Carbon
3 45' Carbon,
low profile
Air-Line
Options
A FireHawk
PTC, single
hose, solid
cover
S FireHawk
PTC,
threaded
hose, solid
cover
C Recue Belt, Long,
50 Ft. Rope
E Rescue Belt,
Swiveling, Standard,
50 Ft. Rope
MMR
Regulator
Type
Cylinder
NIOSH Approved.
Part Number
Non NFPA Compliant.
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
Self-Contained Breathing Apparatus
BlackHawk® Tactical Air Masks
Ultra Elite® Facepiece
• Optional FHR chest strap
• Adjustable Kevlar cylinder retention strap
with over-center latching system
• Cylinder shroud that encompasses the
cylinder and Air Mask pneumatics. Shroud
is made of Advance FHR material
• All-black Ultra Elite facepiece, available in
Hycar or silicone rubber
• Three sizes of facepiece with two sizes of
black nosecups
• HUD System mounting bracket
• SpeeD-ON® Kevlar Head Harness
Cylinders
Mask-Mounted Regulator
• Firehawk® Regulator with Push-to-Connect
feature
• Neoprene intermediate pressure hose
• Variable flow bypass system
• The BlackHawk Air Mask is available in both
low-pressure (2216 psi) and high-pressure
(4500 psi) operating systems
• Carbon- fiber cylinders available for use are:
L-30 Stealth, H-30 Stealth, H-45 Low-Profile
Stealth, H-60 Stealth
EOSTI / Gauge
Quick-Fill® System Option
• Nightfighter Heads-Up Display functions
silently as the low pressure warning device and
the cylinder pressure gauge*
• System consists of a transmitter mounted on
the gauge line and a receiver that mounts on
the facepiece
• A series of LEDs provides the user with
cylinder volume information
• LEDs function in an intermittent mode and can
be refreshed by depressing the refresh button
on the transmitter
BlackHawk® Tactical Air Mask
* There is no audible low-pressure warning device on this unit.
The BlackHawk Tactical Air Mask is
especially designed for tactical situations.
Certain BlackHawk features eliminate
reflections and/or audible sounds that
would compromise concealment—in other
words, it is black, sleek and silent.
• A shoulder-mounted Quick-Fill System option
is offered
Workline Accessory
• For extended-use applications, an air-line
accessory is available with your choice of five
different types of fittings
Rescue Belt
• Emergency egress system integral to the
SCBA waist belt
• Includes Kevlar line and rappelling hardware
Carrying Case
Harness and Carrier
• Composite backplate reinforced with
glass fibers
• Large side handles on the backplate for
pulling the wearer to safety
• Waistbelt, shoulder straps and pull strap
are all made of flame and heat-resistant
(FHR) Kevlar material
• Optional FHR shoulder pads and lumbar
pad (solid or swiveling)
• A hard case or soft case are offered for storage
purposes
CBRN Protection
• Optional CBRN hardened facepiece and
regulator assembly
• Positive protection from CBRN agents
• Same CBRN components as the very popular
FireHawk Air Mask
BlackHawk® MMR Self-Contained Breathing Apparatus Assemble-To-Order (ATO) Matrix
SCBA Type
Carrier/
Harness
Assembly
BL 2216 Black- A Kevlar
Hawk Air
B Kevlar
Mask
with Chest
Strap
C
Kevlar
with
BH 4500 BlackShoulder
Hawk Air
D Pads
Mask
Kevlar
with
Shoulder
Pads and
Chest
Strap
Lumbar Pad/
Rescue Belt†
Cylinder
0
None
0 None
1
Lumbar Pad
1 30' Carbon
2
Swiveling
Lumbar Pad
30' Carbon
2 less Air
A
Rescue Belt - Standard 50'
B
Rescue Belt - Standard 75'
C
Rescue Belt Long 50'
D Rescue Belt Long 75'
E
Swiveling Rescue
Belt - Standard 50'
F
Swiveling Rescue
Belt - Standard 75'
G Swiveling Rescue
Belt - Long 50'
MMR
Regulator
Type
G Firehawk PTC, 0
Solid Cover
1
Firehawk PTC,
R Solid Cover,
2
CBRN
1 30' Carbon
4
6 60' Carbon
less Air
None
0 None
A
None
Snap-Tite
Aluminum
1 Quick-Fill
Shoulder
Mounted
B
Ultra Elite 1 Med
Hycar,
2 Large
Small
Hansen SST
Foster Steel
Snap-Tite
Locking
5 Aluminum
2 45' Carbon
Low-Profile
3
60' Carbon
5 45' Carbon
Low-Profile
less Air
Emergency
Breathing
System
Hansen
3 Brass
0 None
4 30' Carbon
less Air
Air-Line
Options
Option R can
only be chosen
if a Hycar
facepiece
is selected
Facepiece
C
Ultra Elite
Hycar,
Medium
D Ultra Elite
Hycar,
Large
E
Ultra Elite
Silicone,
Small
F
Ultra Elite
Silicone,
Medium
Nosecup
0 None
Head
HUD
Communications Options
Harness
0 None
1 Rubber
2 SpeeDOn
A Standard
Speaking
Diaphragm
B
ClearCommand
Ready
C
ClearCommand Amp
1 NightFighter
HUD
Case
0 None
1 Hard
Case
2 Soft
Case
D ClearCommand
Amp/RI
(Less PTT)
G Ultra Elite
Silicone,
Large
H Swiveling Rescue
Belt - Long 75'
C
Part Number
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
49
Self-Contained Breathing Apparatus
SCBA Key Components
Facepiece Assemblies for FireHawk M7 Air Masks
Ultra Elite® Facepiece
Firehawk® MMR
The MSA Ultra Elite Facepiece offers an effective
combination of comfort and performance.
The Firehawk MMR, MSA’s mask-mounted regulator
assembly, is available with two different attachment
systems, the Firehawk MMR truly redefines ease-of-use
and ease-of-maintenance, combined with outstanding
performance.
Designed to provide exceptional peripheral and
downward vision, the Ultra Elite Facepiece features
a super-soft facepiece texture for a smooth and
comfortable fit. It also resists chemical attack and
temperature extremes, and withstands rugged
day-to-day use without tearing and ripping.
Ultra Elite Facepiece
Heads-Up Display (HUD)
When you open your Air Mask’s cylinder
valve, the HUD automatically activates,
displaying the cylinder pressure reading in
25% increments.
ClearCommand
Communications System
MSA’s ClearCommand Communications
System is designed specifically to meet
the modern communications needs of
firefighters. It features an internally
mounted microphone coupled with a
large-diameter (50mm) amplifier speaker
for optimal clarity and volume. Using a
proprietary circuit design, the system
delivers more than twice the volume
of a facepiece alone. Mounted in an
“out-of-the-way” position, the
ClearCommand System doesn’t block
vision or mechanical communication.
The Ultra Elite’s mechanical voicemitter
is still fully functional, even with the
system installed.
The design of the Ultra Elite Facepiece is based on
extensive anthropometric studies of the face-length,
temple-width and chin-width data from more than
8,000 individuals. The result is a facepiece that provides
improved seals against a wide range of facial contours.
To provide a secure, comfortable fit, the facepiece
utilizes five adjustable straps with stainless steel,
field-replaceable buckles that resist chemical attack.
The straps also feature slightly larger adjustment tabs
that are easier to manipulate, even with gloves on.
For slip-on convenience, the Ultra Elite Facepiece can be
equipped with the SpeeD-ON® Facepiece Harness. Made
of flame- and heat-resistant Kevlar Fabric, the harness
features a hair-net type, five-point suspension that can
be easily and securely adjusted at each point.
Lenses on MSA full facepieces are molded from
polycarbonate, and a special super hardcoating provides
a tough, durable facepiece lens to resist scratching.
HUD Display
The Firehawk second-stage regulator features a unique
Slide-To-Connect (STC) attachment system that allows
firefighters to hang the regulator on the facepiece in the
“ready position,” then simply push it into the facepiece
when SCBA air is needed. Doffing of the regulator, while
wearing gloves, is also easy with two large release
buttons that automatically turn-off the flow of air as the
regulator is doffed. A dual-swivel feature on the pressure
hose provides maximum freedom-of-head movement
and the silicone hose material ensures hose flexibility
even at very cold temperatures.
In addition to the STC system, MSA also offers a second
connection option for the Firehawk Regulator, the
Push-to-Connect (PTC). The PTC’s Adapter self-centers
the Firehawk regulator and the loud dual sound of the
regulator engaging onto the facepiece provides you with
confidence that the Firehawk PTC is securely attached to
your facepiece—an action that takes just seconds, when
seconds count!
Maintenance is also a breeze, considering the Firehawk
design requires no tools, adhesives, or sealants, and has
approximately 70% fewer parts as compared to other
regulators on the market. Additionally, there are no
internal adjustments required. Any adjustments to the
regulator may be accomplished at a single adjustment
point through the outlet port of the regulator.
Ease of use and maintenance, combined with
outstanding performance, makes the Firehawk MMR
clearly the product of choice.
Ultra Elite M7 Facepiece, SpeeD-ON Head Harness, Nosecup and M7 HUD Bracket
Firehawk STC
50
Firehawk PTC
Standard speaking
diaphragm
ClearCommand
ready
Standard speaking
diaphragm
ClearCommand
ready
Small
10084689
10084821
Small
10084690
10084822
Medium
10084823
10084825
Medium
10084824
10084826
Large
10084827
10084829
Large
10084828
10084830
Spare / Replacement
M7 HUD
10091446 M7 HUD
10091447 M7 HUD with bracket
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
Self-Contained Breathing Apparatus
Emergency Breathing Systems
Emergency Egress System
Rescue Belt
In a continuation of MSA’s pursuit of firefighter safety, the Rescue Belt is being introduced to the fire service. This is an
NFPA-compliant emergency egress system that is unique to MSA. The belt can be integrated into the carrier and harness
assembly of the MSA Vulcan or Airframe Carrier and Harness assemblies. A 50 foot or 75 foot Kevlar line with a descender
and carabiner is weaved into the belt to allow a trapped fire fighter to escape to either the ground or to a floor below the fire.
The belt is available in three lengths, standard (56 inches), mid-size (66 inches) and long (76 inches).
Rescue Belt
Standard Size Rescue Belt
Mid-Size Rescue Belt
Long Rescue Belt
50' Kevlar Line
10052766
10071003
10052767
75' Kevlar Line
10052768
10071004
10052769
Carrier & Harness Assembly
FireHawk M7 Carrier and Harness Assembly
The one component of any SCBA that has
the most impact on firefighter comfort is
the carrier and harness assembly. MSA is
introducing a new carrier and harness
assembly that places an emphasis on
firefighter comfort while maintaining the
robustness and reliability that is expected
in the fire service. The carrier and harness
comes standard with large side handles
and a central attachment point for pulling
firefighters to safety in rescue scenarios.
The swiveling lumbar pad provides
maximum freedom of movement and
comfort when crawling or climbing.
FireHawk M7 Carrier and Harness Assemblies
Part No.
Pressure
Low
10086663
High
X
10086662
X
10086664
X
10086665
Chest
Strap
Swiveling
Lumbar Pad
Yes
Yes
Yes
Yes
Yes
X
Yes
Accessories
10083134
Replacement FireHawk M7 Lumbar Pad
10012167
Chest Strap
The assembly utilizes the proven pieces
from previous generations of Air Masks such as the tunneled shoulder straps for hose containment, and tri-bar slides for
easy removal/installation of the waist belt and shoulder straps.
All units are equipped with double-pull waist belts and an optional chest strap is available.
Cylinders
Carbon-Wrapped Cylinders
Carbon-wrapped Cylinders are
the lightest SCBA air cylinders
ever developed by MSA. They
feature a unique outerwrap made
of lightweight, high-performance
carbon fibers, which reduces
cylinder weight by two to six
pounds when compared to
fiberglass-wrapped cylinders
and as much as ten pounds when
compared to aluminum cylinders.
They are available in five models
to accommodate a wide range
of applications.
Cylinders for SCBA
Part No.
Cylinder Type
(Cylinder & Valve)
NIOSH Service
Rating Life
Pressure
Weight**
(empty)
807586
L-30* Carbon-Wrapped
30-minute
2216 psig
8 lb – 0 oz.
816115
L-30+* Carbon-Wrapped
30-minute
3000 psig
9 lb – 8 oz.
807587
H-30* Carbon-Wrapped
30-minute
4500 psig
7 lb – 4 oz.
807570
H-45* Carbon-Wrapped
45-minute
4500 psig
9 lb – 7 oz.
H-45 Low-Profile*
10035644
Carbon-Wrapped
45-minute
4500 psig
9 lb – 10 oz.
807588
H-60* Carbon-Wrapped
60-minute
4500 psig
11 lb – 12 oz.
469619
Fiberglass Hoop-Wound
30-minute
2216 psig
13 lb. – 0 oz.
809872
Aluminum
30-minute
2216 psig
18 lb. – 0 oz.
*These cylinders are capable of custom options.
**All weights shown are approximate.
For more information see Bulletin 0108-11-MC. See Bulletin 0108-13-MC for information on custom-logoed cylinders for your MSA Air Mask.
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
51
Self-Contained Breathing Apparatus
MSA Accountability System
Accountability is key to every firefighter’s safety on a fire scene. MSA’s new
optional Accountability System revolutionizes fireground safety by combining
the latest computer software with a high-performance radio module and the
field-proven technology of MSA’s ICM Tx Integrated PASS.
A new way to monitor vital information
• Each MSA base station can monitor up to 50 firefighters, and you can use
multiple base stations on a single computer.
• The FireHawk M7 Air Mask with telemetry transmits to incident command
the firefighter’s name, team assignment, cylinder pressure, service-time
emaining, PASS alarms (motion or manual), thermal alarms, battery status,
radio connectivity, and evacuation acknowledgement.
A fireground management system
• Personalized ID tags for each firefighter tell incident command exactly who
is on scene.
• An integrated PAR (personnel accountability report) timer helps manage
radio calls to each team.
• Incident command can manually add firefighters who are not wearing an
SCBA or mutual aid firefighters, so all personnel can be accounted for.
Intuitive and easy to use
• Assign firefighters to teams by clicking on a firefighter’s icon and dragging it
to another team.
• A volume of critical information is available at a glance of the screen, due to
the large number of firefighters that can be displayed and the pictorial format of the information.
• Receive both audible and visual indications of critical events such as PASS
alarms or low-pressure alarms.
Accountability System Base Station Kits
10072240
Accountability Base Station Kit (includes software, magnetic antenna
kit, USB cable, wall mount cable, and 8-24 volt power cable)
10098767
Accountability Base Station Kit (includes software, fixed antenna kit,
USB cable, wall mount cable, and 8-24 volt power cable)
revolutionizes
tability System
un
co
Ac
7
M
’s
the latest com
MSA
ty by combining
fireground safe th a high-performance radio
wi
puter software
technology of
e field-proven
module and th
.
SS
PA
ed
at
gr
Inte
MSA’s ICM TxR
A two-way evacuation feature
• Incident command is assured that firefighters receive all evacuation messages.
When incident command transmits the alarm through the FireHawk M7 Air
Mask, they’ll know the firefighter received it, because the unit automatically
sends a confirmation message to the base station.
• By simply pressing a button on his/her own control module, a firefighter can
send a manual confirmation to acknowledge that they have received and
understand the critically important evacuation message.
• Firefighters will hear the evacuation alarm on their own personal PASS device.
Also, visual indications in the HUD and an icon on the control module will alert
the firefighter that it is time to evacuate.
• An individual firefighter, a team of firefighters, or all firefighters can be
evacuated with the click of a button.
• Although certain concrete and steel commercial structures can challenge any
radio signal, MSA’s Accountability System coverage with radio technology
provides highly reliable performance for a 1-mile line-of-sight range.
• Due to the spread-spectrum design, it does not interfere with other high-band
radio frequency equipment.
• For additional safety, both base station and firefighter modules have an
icon message to inform users if a firefighter falls out of radio signal range,
so that alternate accountability measures, such as voice radio contact with
teammates, can be taken.
Accountability System
10083876
M7 Control Module Reader / M7 ID tag writer
10083875
M7 ID tags
10075756
Antenna kit with magnetic base
10098766
Antenna kit with fixed base
10063880
USB cable
10049410
8-24 volt, power cable
10047342
Wall mount power cable
Field Maintenance and Repair
The program is supported with personalized training
tailored to customers’ needs and taught in the field
by MSA-authorized personnel.
User maintenance covers procedures necessary to
conduct general cleaning, inspection, and limited
maintenance in accordance with the Occupational
Safety and Health Administration (OSHA), National
Fire Protection Association (NFPA), and the American
National Standards Institute (ANSI) standards.
MSA offers a complete program for
maintenance and repair of MSA Air Masks.
52
C.A.R.E. Certified Air Mask Repair Education covers all
maintenance for both low- and high-pressure SCBA.
Air Mask inspection and maintenance can be
performed by MSA or a factory-authorized service
center. Or, individuals can obtain training for C.A.R.E
certification from MSA. By having a C.A.R.E-certified
technician on staff, fire departments and other
facilities with a large number of Air Masks can
perform all inspection and maintenance in-house.
• All repairs and maintenance can be done
in the field.
• A selection of overhaul kits, spare parts, and
tool kits is available.
• Users may conduct periodic performance
testing using an authorized MSA regulator
tester.
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
Self-Contained Breathing Apparatus
Emergency Breathing Systems
The Quick-Fill System
Replacement Parts for the Quick-Fill System
485366
EBS hose package, includes 3-foot emergency transfill hose in Kevlar pouch
485331
Emergency transfill hose, less Kevlar pouch
485390
Kevlar pouch
485391
Male stainless steel quick-disconnect with SAE-10 thread, complete with
dust cover (also for use as a fitting for customized refilling systems)
485392
Female quick-disconnect with SAE-4 thread, complete with dust cover
Quick-Fill Hoses
25-ft lengths are stocked; other “custom lengths” are available on a special material basis. All SAE
Fittings are for high-pressure service. Female quick-disconnect fittings have dust covers.
The Quick-Fill® System
The patented Quick-Fill System lets MSA
Air Mask users refill and transfill air cylinders
while the SCBA is worn, without removing
the air cylinder—even in IDLH atmospheres.
Use this MSA-exclusive option to:
• Fill an SCBA cylinder from a mobile
compressor or cascade system in less
than a minute.
• Transfill between two cylinders, providing
an Emergency Breathing System.
• Extend the air supply over longer
durations, using a remote compressed-air
source.
25 ft
12 ft
10 ft
8 ft
6 ft
3 ft
485332
802690
802689
802688
802687
485331
FQD x FQD
487907
802677
802675
802673
802671
492796
FQD x CGA-347 Outlet
487909
802685
802683
802681
802679
487427
FQD x CGA-347 CN
487906
802704
802703
802702
802701
802705
FQD x SAE-4
487908
802678
802676
802674
802672
492797
FQD x CGA-346 Outlet
487910
802686
802684
802682
802680
487428
FQD x CGA-346 CN
Because performance is not affected, MSA
Air Masks retain NIOSH certification during
use of the Quick-Fill System.
Air Masks compliant to recent NFPA
standard have the Quick-Fill URC fitting
located at the Audi-Larm warning device.
A Quick-Fill hose with a quick-disconnect
connects the air source to the adapter for
air transfer. See Bulletin 0105-92-MC
for a Question & Answer overview of
Quick-Fill Systems.
RescueAire™ II Portable Air-Supply System
The RescueAire II Portable Air Supply System is designed to meet the
needs of Rapid Intervention Teams (RITs). The system consists of a
lightweight Carbon-Wrapped cylinder, Quick-Fill® emergency breathing
system, ExtendAire™ emergency breathing system, and an MMR
regulator, supported by a flame- and heat-resistant harness. The
RescueAire is a complete system that can provide emergency breathing
air for most any victim.
The RescueAire II System is available in both low-pressure (2216 psig)
and high-pressure (4500 psig) versions. An optional-use shoulder strap is
also provided for hands-free carrying.
RescueAire™ II Portable Air-Supply System
with L-30 cylinder less cylinder Low-Pressure (2216 psig)
10100096
10100095
RescueAire II w/Firehawk Responder MMR
10041196
10041198
RescueAire II, Firehawk STC MMR
10041230
10041232
RescueAire II, Firehawk PTC MMR
with H-60 cylinder less cylinder High-Pressure (4500 psig)
The ExtendAire™ System
The ExtendAire System can be used as both
an emergency breathing system and a
dual-purpose device for MMR SCBA to allow
firefighters to quickly and easily connect to
an air-line.
10100097
10100094
RescueAire II w/Firehawk Responder MMR
10041195
10041197
RescueAire II, Firehawk STC MMR
10041199
10041231
RescueAire II, Firehawk PTC MMR
The ExtendAire™ System
812958
ExtendAire Air-line Hose with foster plug
812973
40" Rescue Hose
10031798 ExtendAire Upgrade Kit for Threaded Firehawk MMR
10031797 ExtendAire Upgrade Kit for Quick-Connect Firehawk MMR
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
53
Self-Contained Breathing Apparatus
ClearCommand® HCS Helmet Communication System
The Helmet Communication System from MSA is a state-of-the-art radio interface device which
significantly improves the user’s ability to receive and send messages even in loud ambient-noise
environments. It goes wherever you go. The system consists of a helmet-mounted microphone
and ear speaker assembly that weighs 5.3 ounces and easily snaps onto the user’s fire helmet or
industrial-style helmet’s ratchet suspension. The helmet mic/ear speaker assembly connects to a
lapel microphone or optional stand-alone PTT (push-to-talk) unit. The lapel microphone and PTT
are permanently fitted with a connector for attachment to the specific radio of choice. The
Helmet Communication System also offers a plug-in truck communication adapter that can be
used by firefighters, along with their helmet microphone assembly, on the way to a fire scene or
other incident. Once the firefighter arrives at the scene, the truck system cable is unplugged from
the helmet microphone, and the helmet microphone cable end is connected to the user’s lapel
mic or PTT.
The user of the Helmet Communication System has uninterrupted communication from
the time the alarm sounds until the incident is over.
For more complete information, see Bulletin 3639-01-MC.
Helmet Microphone Assembly
10042902 Helmet Microphone Assembly (includes Custom Fitted Flannel Headband Liner)
Helmet Mic with
Stand-Alone PTT
Helmet Mic
with Lapel Mic
Lapel Mic Kits for Radio Interface*
10042908 Maxon SP120, SP130, SP140
10042909 Motorola HT600, MT1000, MTX820, MTX900, Radius P200 & P500
10042903 Motorola HT1000, JEDI, MT2000, MTS2000, MTX838, MT839, MTX8000, MTX9000
10042904 Motorola Astro and Saber
10042905 Motorola Radius GP300, P110, SP50, LTS2000, Spirit-III, GTX, SP21
Features & Benefits
• Incorporates a “noise-eliminating” bone-conduction voice
transmitter that virtually eliminates high ambient noise levels.
• Custom user-fitted ear speaker brings all incoming
communication directly to the user’s ear. No need to lift
your lapel mic up to your ear to hear transmission.
• Easily snaps onto the ratchet suspension of fire helmets or
industrial-style helmets. The unit can be easily transferred to
other users, and no tools are required for removal.
• Can be used over the top of facepiece head harnesses, hoods
and liners without losing the quality of the transmission.
• The bone-conduction microphone is made of soft silicone
material, which makes it comfortable to wear, with no
pressure points.
• The helmet microphone assembly can be reversed on the
helmet suspension to position the ear speaker on either ear.
• The helmet mic system, when used with the lapel mic or PTT,
is powered by the battery from the radio. No need to replace
or re-charge dry cells.
• Special connectors suitable for most common radios are
available for the lapel microphone and PTT, which allows users
to adapt the system to their existing radios.
• The helmet mic is NFPA-certified which allows its use while
fighting fires.
• Intrinsic safety approvals allow the use of the Helmet
Communication System in hazardous environments.
• The stand-alone PTT unit is designed for use under hazardous
material suits. The large button makes it easy for the user to
depress and communicate.
• The helmet mic incorporates a cable keeper which allows for
storage of the cable when it’s not connected to the lapel mic
or PTT.
54
10042912 Motorola STX, MX800, MX840
10042906 GE Ericsson PCS, PC2005
10042907 GE Ericsson MRK, LPE-200, Prism, PX 126T
Stand-Alone PTT Kits for Radio Interface*
10045667 Maxon SP120, SP130, SP140
10045668 Motorola HT600, MT1000, MTX820, MTX900, Radius P200 & P500
10045662 Motorola HT1000, JEDI, MT2000, MTS2000, MTX838, MT839, MTX8000, MTX9000
10045663 Motorola Astro and Saber
10045664 Motorola Radius GP300, P110, SP50, LTS2000,Spirit-III, GTX, SP21
10045669 Motorola STX, MX800, MX840
10045665 GE Ericsson PCS, PC2005
10045666 GE Ericsson MRK, LPE-200, Prism, PX 126T
Truck System
10045732 Nexus Adapter, D. Clarke
10045731 Phonejack Adapter, D. Clarke
Parts and Accessories
10046087 Dust Cover
10046123 Guard Ring, Tall
10046122 Guard Ring, Short
10046089 Belt Clip Assy, Standard
10046120 Belt Clip Assy, Clothes Pin Type
10046121 O-Ring, Single Pin Connector
10045778 Flannel Head Band Liner
*If your specific radio is not listed, please contact MSA Customer Service.
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
Self-Contained Breathing Apparatus
ClearCommand Communications System for Ultra Elite Facepieces
ClearCommand System Kits
10024074 Amplifier Kit, complete with microphone
10051290 Amplifier Radio Interface Kit, w/ microphone, less PTT
10023055 Microphone Kit, with mounting bracket
Lapel Mic Kits for Radio Interface*
10042908 Maxon SP120, SP130, SP140
10042909 Motorola HT600, MT1000, MTX820, MTX900, Radius P200 & P500
10042903 Motorola HT1000, JEDI, MT2000, MTS2000, MTX838, MT839, MTX8000, MTX9000
10042904 Motorola Astro and Saber
10042905 Motorola Radius GP300, P110, SP50, LTS2000, Spirit-III, GTX, SP21
10042912 Motorola STX, MX800, MX840
10042906 GE Ericsson PCS, PC2005
10042907 GE Ericsson MRK, LPE-200, Prism, PX 126T
MSA’s ClearCommand Communications System is
designed specifically to meet the modern
communications needs of firefighters. Because
it’s available in two versions, amplifier and amplifier
with radio interface, firefighting teams can be properly
fitted for the job at hand. Also, the systems are designed
for “shared-use” of the amplifier with a unique “bus-bar”
arrangement, so individual issue is not required.
Stand-Alone PTT Kits for Radio Interface*
The ClearCommand systems feature an internally
mounted microphone coupled with a large-diameter
(50mm) amplifier speaker for optimal clarity and
volume. Using a proprietary circuit design, the system
delivers more than twice the volume of a facepiece
alone. Mounted in an “out-of-the-way” position,
the ClearCommand System doesn’t block vision or
mechanical communication. The Ultra Elite’s
mechanical voicemitter is still fully functional,
even with the system installed.
10045669 Motorola STX, MX800, MX840
The radio interface version features the same amplifier
as the amp-only version, combined with an ear-speaker
for incoming radio messages and a lapel mic assembly
for interface with over 100 radios. The lapel mic can be
used as a component of the ClearCommand system or
as a stand-alone hand mic.
Both the amplifier and radio interface models are
intrinsically safe, and meet the applicable requirements
of NIOSH and NFPA 1981, 2002 edition.
MSA University, MSA’s premier
online training center,
offers a wide range of training
and informational materials.
Register today at
www.MSAnet.com/MSAU
10045667 Maxon SP120, SP130, SP140
10045668 Motorola HT600, MT1000, MTX820, MTX900, Radius P200 & P500
10045662 Motorola HT1000, JEDI, MT2000, MTS2000, MTX838, MT839, MTX8000, MTX9000
10045663 Motorola Astro and Saber
10045664 Motorola Radius GP300, P110, SP50, LTS2000,Spirit-III, GTX, SP21
10045665 GE Ericsson PCS, PC2005
10045666 GE Ericsson MRK, LPE-200, Prism, PX 126T
Truck System
10045732 Nexus Adapter, D. Clarke
10045731 Phonejack Adapter, D. Clarke
Parts and Accessories
10046087 Dust Cover
10046123 Guard Ring, Tall
10046122 Guard Ring, Short
10046089 Belt Clip Assy, Standard
10046120 Belt Clip Assy, Clothes Pin Type
10046121 O-Ring, Single Pin Connector
10045778 Flannel Head Band Liner
*If your specific radio is not listed, please contact MSA Customer Service.
Shop Online for MSA Gear
MSA FireSlayer and Be Ready promotional items are available to
anyone via MSA's Internet site. Sporting appropriate logos are
shirts, duffels, caps, golf items, mugs, money clips, lighters and
more. The FireSlayer logo helps promote our products to the
firefighting market, while the Be Ready logo is aimed at Homeland
Security. Look for the "MSA Gear" link in the Resources & Info area
after selecting MSA North America; MSA United States from the
MSA homepage at MSAnet.com.
After making your selections, complete the shipping information
and furnish a credit card number. Your order will be processed, and
you should receive it within a week. Express service is also available.
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
55
Self-Contained Breathing Apparatus
SCBA Accessories
APR Adapter
MSA’s APR adapter provides firefighters with the
versatility they need to perform all tasks at the
fire ground with one common facepiece. From
fire-fighting to overhaul to homeland security,
firefighters can switch from a positive-pressure
facepiece to a negative-pressure air-purifying
respirator simply by engaging the APR Adapter.
The APR Adapter uses MSA’s comprehensive
family line of air-purifying cartridges; select
from the Advantage cartridges or our CBA/RCA
canisters to protect against a multitude of
airborne contaminants.
The APR Adapter is designed for use in non-IDLH
environments and is NIOSH-approved. Contact
MSA for more information.
APR Adapters
Firehawk MMR Firehawk MMR
APR Adapter
STC Version
PTC Version
10032511
10040052
APR Adapter
10032927
10040055
APR Adapter Individual Kit
10032925
10040054
APR Adapter Truck Kit
Accessories
10037809
Ultra Elite, Anti-Fog Applique (10/pkg)
10037810
Ultravue, Anti-Fog Applique (10/pkg)
817590
CBA/RCA Canisters (box of 6)
809858
Replacement Baffle
813341
Replacement Bayonet Cover
Spectacle Kit for Full-Facepiece Respirators
For use by workers who must wear corrective lenses, the Spectacle Kit can be easily inserted into the
facepiece. The kit includes a wire support, rubber guide, and pair of metal-frame spectacles. There are two
kits for the Ultra Elite facepiece; one uses a side wire support to hold the lenses in the facepiece, while the
other uses a center support to position the unit. Desired adjustment is obtained by moving the spectacles in
and out of the rubber guide and up and down the wire support. One size of spectacle frame is used (S-7
shape, 48-mm lens size) with Universal Bridge Corrective Lenses that can be obtained from local sources.
The Spectacle Kit can be used with a nosecup.
Side-Support Spectacle Kit
for Ultra Elite Facepiece
Center-Support Spectacle Kit
for Ultra Elite Facepiece
Nosecups
Spectacle Kits
804638
Ultra Elite Spectacle Kit (side wire support)
493581
Ultra Elite Spectacle Kit (center support)
High-Pressure Filling Hose
Provides a convenient means to connect and charge high-pressure air
into a high-pressure 4500 psig cylinder.
High-Pressure Filling Hose
476105
Molded from a soft rubber compound that is
resistant to facial oils, the optional nosecup
helps reduce the possibility of lens fogging.
The nosecup is particularly effective under
conditions of high humidity and/or low
temperatures by inhibiting contact of moist
exhaled air with the facepiece lens. A nosecup
can be easily affixed to the facepiece without
tools. Any size nosecup may be installed in any
size Ultra Elite Facepiece for a customized, more
comfortable fit.
Nosecups
56
High-Pressure Filling Hose Assembly
Accessories for Filling Low-Pressure (2216 psig) Cylinders
Accessories for Filling Low-Pressure Cylinders
68846
Air Outlet Connection, complete w/ Gauge
495188
Medium Black Nosecup
68850
Air Coupler Tee
495189
Large Black Nosecup
68851
Air Pigtail
476156
Low-Pressure Air-Filling Hose, 5 feet long
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
Fire Service Helmets
Cairns® Fire Helmets
Cairns Fire Helmets: Quality Craftsmanship Since 1836
Since 1836, Cairns has been the original manufacturer of
leather firefighting helmets. Today, Cairns leather
helmets retain the same authentic look and quality that
generation after generation of firefighters have relied
upon. And now, these helmets are also made with the
added protection necessary for today’s standards of
safety in the firefighting industry.
Cairns also applies the same tradition of excellence
to its newer lines of firefighting helmets. Both
traditional and modern designs feature the very best
N6A Houston
(NFPA compliant)
in contemporary high-tech materials, such as
lightweight but durable fiberglass/Kevlar composites
and tough, high-temperature thermoplastic.
All helmets are available with many options, including
choice of colors, chinstraps, earlap material, etc. Also,
a variety of accessories is available to complement Cairns
fire helmets. Faceshields, goggles, ear/neck protection,
and fronts can all be selected to configure the exact
helmet you need.
Leather Helmets
The original leather helmet, individually hand-crafted to meet today’s OSHA and
NFPA standards with over 173 years of dependable performance.
Leather Helmet Features & Benefits
• Hand-crafted, 100% leather shell.
• Insurance against fireground
damage with Cairns’ 5-year shell
replacement warranty.
• Non-corroding, high-temperature,
glass-filled polymer faceshield/goggle hardware.
• Faceshield wing protectors for extra
faceshield reinforcement.
• Nomex chinstrap with one-hand
quick release buckle and postman
slide allows quick and easy
adjustment.
N5A New Yorker
(OSHA compliant)
• Choice of Nomex or PBI/Kevlar
earlap for increased neck/ear
coverage and protection.
• High-temperature foam cap
increases thermal and impact
protection.
• High-temperature impact cap
liner resists distortion at high
temperatures.
• Comfortable fit for all head sizes
between 6-3/8 inches and
8-3/8 inches.
• Large diameter helmet hanger fits
on larger hooks and racks.
Cairns® 1044
Traditional Helmets
Traditional style combined with high-tech performance.
Traditional Helmet Features & Benefits
• Cairns exclusive Defender Visor
for Cairns 1010 and Cairns 1044
fire helmets.
• Simple rear ratchet height
adjustment to fit all head sizes.
• Market-leading 5-year shell
replacement warranty.
• Non-corroding, high-temperatureresistant, faceshield/goggle
hardware.
• Rugged, high-temperature edge will
not melt or drip.
• Easy front headband adjustment
for proper SCBA mask fit.
Classic™ 1000
• Headband (6 3/8 to 8 3/8) fits a
wide variety of head sizes.
• Durable helmet hanger fits on
large hooks and resists bending.
• Minimal parts for lower service cost
and easier maintenance.
• Exclusive shell release system
for an extra margin of safety
(except 880).
• Unique tube-lock system absorbs
the shock of an impact.
For ordering information, replacement parts and accessories,
contact your MSA Fire Service Distributor.
880 Tradition
Cairns® 1010
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
57
Fire Service Helmets
Cairns® Fire Helmets
Modern Helmets
Different models for applications such as structural
firefighting and EMS/rescue.
Invader™ 664
660C Metro®
Structural 360S®
Intruder 990®
Modern Helmet Features & Benefits
• Defender Visor now available on 660C Metro and
Invader 664!
• Market-leading 5-year shell replacement warranty.
• Non-corroding, high-temperature-resistant,
faceshield/goggle hardware.
• Rugged, high-temperature edge will not melt or drip.
• Easy front headband adjustment for proper SCBA
mask fit.
• Simple rear ratchet height adjustment to fit all
head sizes.
• Headband (6 3/8 to 8 3/8) fits a wide variety of
head sizes.
• Durable helmet hanger fits on large hooks and
resists bending.
• Minimal parts for lower service cost
and easier maintenance.
• Exclusive shell release system for an extra margin
of safety (except 360S and HP3).
• Unique tube-lock system absorbs the shock
of an impact (except 360S).
For ordering information, replacement parts and
accessories, contact your MSA Fire Service Distributor.
Cairns Rescue Helmets
Rescue Helmets Features & Benefits
Rescue 360R
Commando® HP3
• Defender Visor now available on Commando HP3!
• Market-leading 5-year shell replacement warranty.
• Non-corroding, high-temperature-resistant, faceshield/goggle
hardware.
• Rugged, high-temperature edge will not melt or drip.
• Easy front headband adjustment for proper SCBA mask fit.
• Simple rear ratchet height adjustment to fit all head sizes.
• Headband (6 3/8 to 8 3/8) fits a wide variety of head sizes.
• Durable helmet hanger fits on large hooks and resists bending.
• Minimal parts for lower service cost and easier maintenance.
Rescue 360R-13
For ordering information, replacement parts and
accessories, contact your MSA Fire Service Distributor.
58
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
Fire Service Helmets
Cairns® Fire Helmets
Defender® Visor for Cairns Traditional and Modern Helmets
MSA’s Defender Visor for Cairns 1010 and 1044 Traditional Helmets and 660C Metro, Invader 664, and Commando
HP3 Modern Helmets offers eye protection from dust, dirt, and grit. Sleek and attractive construction allows for fast,
easy raising and lowering of your visor even with gloved hands. Visor stays clean inside
your helmet until needed for eye protection during overhaul and non-IDLH
search-and-recovery. The Defender Visor exclusive integral design is retractable
for the ultimate in compact convenience. Standard clear and amber Tuffshield
visor options are NFPA-compliant.
If you’re looking for a new Cairns Traditional or Modern Helmet, or if you've
thought about replacing your existing impact cap, consider the streamlined
advantage of the new NFPA-compliant MSA Defender Visor. Cairns
Traditional and Modern Helmets offer the perfect combination of durability
and performance in lightweight, high-performance designs. Cairns once again
integrates the latest technological advances expected by firefighters.
New Cairns 1010 and 1044 Helmet assemblies or 660C Metro, Invader 664,
and Commando HP3 Helmets incorporating the Defender Visor may be
ordered through Traditional or Modern Helmets Assemble-To-Order Matrices.
A user-installable upgrade kit (includes new impact cap) lets you install the
Defender Visor yourself.
Standard 1010 Defender Configurations
Features and Benefits
1010DS
Includes Standard Flannel Cushion Liner, Yellow Nomex Earlap, Silk-Screened 6" Eagle Front Holder and
Clear Defender Visor
• Available on Cairns 1010/1044
Traditional and 660C Metro, Invader
664, and Commando HP3 Modern
Helmets
• Standard clear and amber Tuffshield
visors are compliant with NFPA 1971;
all Defender Visors meet ANSI Z87.1+
Standard
• Retractable eyewear system that’s
ready when you need it
• Available with new helmets or as
user-upgrade kit
• Quick-disconnect for fast lens
change-out without tools
• Never lose or misplace your
goggles again
• Optically correct lens eliminates
peripheral distortion
1010DD
Includes Leather Cushion Liner, Flannel Crown Pad, PBI/Kevlar Earlap, Carved 6" Eagle Front Holder and
Clear Defender Visor
1010TS
Includes Standard Flannel Cushion Liner, Yellow Nomex Earlap, Silk-Screened 6" Eagle Front Holder and
Tuffshield Defender Visor
1010TD
Includes Leather Cushion Liner, Flannel Crown Pad, PBI/Kevlar Earlap, Carved 6" Eagle Front Holder and
Tuffshield Defender Visor
Standard 1044 Defender Configurations
1044DS
Includes Standard Flannel Cushion Liner, Yellow Nomex Earlap, Silk-Screened 6" Eagle Front Holder and
Clear Defender Visor
1044DD
Includes Leather Cushion Liner, Flannel Crown Pad, PBI/Kevlar Earlap, Carved 6" Eagle Front Holder and
Clear Defender Visor
1044TS
Includes Standard Flannel Cushion Liner, Yellow Nomex Earlap, Silk-Screened 6" Eagle Front Holder and
Tuffshield Defender Visor
1044TD
Includes Leather Cushion Liner, Flannel Crown Pad, PBI/Kevlar Earlap, Carved 6" Eagle Front Holder and
Tuffshield Defender Visor
Standard Fronts
Crash Fire Rescue (CFR) Proximity System
Made with your choice of high-gloss patent
leather or dull-finish genuine leather reinforced
with a high-temperature, shrink-resistant
back layer and sewn with high-temperature,
fire-retardant Nomex thread.
• Easy to don and doff, this CFR System is
compliant with NFPA 1971-2007.
• Designed and approved for use with the
Metro 660C, Invader 664, Cairns 1010
and Cairns 1044 Fire Helmets, it will not
interfere with the SCBA while in use.
• Components consist of an aluminized
PBI/Kevlar layer, vapor barrier and
inner layer.
The Choice Is Yours!
Standard fronts offer over 27 million possible
configurations! Design your own standard
front by choosing from the options and then
indicating your preferences by calling
1-877-MSA-FIRE to place your order.
Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com
59
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement