Swenson Spreader EV-Select V-Box Spreader Installation and Operating Instructional Manual
The EV-Select V-Box Spreader is designed to be installed on a standard 34” wide truck chassis or inside a dump body. It can be used to spread materials such as salt, sand, and gravel. The spreader has a variety of features that make it easy to use, including a hydraulic system that allows you to control the speed of the conveyor and spinner, and internal and external spinner baffles that allow you to adjust the spread pattern.
Advertisement
Advertisement
DO NOT THROW AWAY
INSTALLATION and OPERATING INSTRUCTIONAL MANUAL
READ BEFORE INSTALLATION
EV-SELECT V-BOX MATERIAL SPREADERS
Manual No. 00118-051-01 REV C
June 08, 2010
1
See page 4 for
Table of Contents
.
SAFETY PRECAUTIONS
THE BEST SAFETY DEVICE IS A CAREFUL OPERATOR!
This symbol means
Become Alert!
ATTENTION!
Your safety is involved!
Please read and understand completely before operating!
Improper use of this equipment can result in serious injury.
To reduce this possibility give complete and undivided attention to the job at hand, and follow these safety precautions.
PREPARATION:
Know your controls. Read this instruction manual. Learn how to stop the equipment quickly in an emergency.
Do not allow children to operate machine; nor adults to operate it without proper instructions.
Keep all individuals not involved in the use of the equipment a safe distance away.
OPERATION:
Observe settings on all equipment controls, and shut off all equipment before starting engine so equipment will not intentionally operate when engine is started.
Always check area around machine before engaging or operating controls.
Always wear relatively tight and belted clothing when operating equipment. Loose jackets, shirts, sleeves or other loose clothing should not be worn because of the danger of catching them in moving parts or controls.
Stop and inspect equipment if unusual movement, sounds or noises are observed.
Repair damage before restarting and operating the equipment.
Disengage power to all operating equipment: (1) before leaving operator’s position,
(2) before making any repairs, adjustment, or cleaning, or (3) when not in use.
Take all possible precautions when leaving the equipment unattended; such as disengaging the hydraulic system from the vehicle engine, shifting vehicle out of gear, setting parking brake, shutting off engine and removing key.
NOTICE:
INSTALLATION OF LIGHT BAR (If furnished)
1. DEPENDING UPON DISTANCE LIGHT BAR IS INSTALLED ABOVE GROUND,
LIGHTING IN LIGHT BAR MAY NOT MEET FEDERAL LIGHTING REGULATIONS.
EQUIPMENT INSTALLER IS RESPONSIBLE FOR MAKING SURE ALL LIGHTING
MEETS FEDERAL LIGHTING REGULATIONS.
2. ANY ADDITIONAL WIRING CONNECTIONS MADE ON TRUCK CHASSIS FOR
“OPTIONAL” LIGHTING ON LIGHT BAR MUST BE MADE ACCORDING TO
VEHICLE MANUFACTURER’S RECOMMENDATIONS.
3. It is the responsibility of the owner of this spreader to replace any and all safety decals which become unreadable or otherwise defaced, and to apply the new decals to the spreader in a secure manner in the same location as the old decals.
Read and observe all “DANGER” and “CAUTION” safety decals appearing on equipment.
The following safety decals appear in various locations on your equipment. The sizes of the decals shown in this manual have been reduced in order to save space.
Refer to page 3 for the location of safety decals on your equipment.
2
PAGE 2
This decal appears on the back left side of the spreader. It cautions all to observe general safety procedures when operating this equipment.
This decal appears near the spinner assembly on the back of the spreader. It alerts all to the danger of being struck by material being spread by the spinner assembly which could result in serious personal injury.
This decal appears on the back and front left and right sides of spreader. It alerts all to the danger of being caught inside the spreader when it is turned on, and where serious personal injury could result.
This decal appears on the back and front left and right sides of spreader. It alerts all to the danger of being caught in the dropout opening of the spreader conveyor where serious personal injury could result.
3
PAGE 3
TABLE OF CONTENTS
Safety Precautions-------------------------------------------------------------------------------------------------------------- 2-3
Table of Contents -------------------------------------------------------------------------------------------------------------------4
Installation Instructions ------------------------------------------------------------------------------------------------------ 5-12
Operating Instructions ------------------------------------------------------------------------------------------------------- 13-15
Recommended Regular Maintenance---------------------------------------------------------------------------------------- 16
Hydraulic Trouble Shooting & Specifications ------------------------------------------------------------------------------- 17
Feedgate Assembly ------------------------------------------------------------------------------------------------------------- 18
Idler Assembly -------------------------------------------------------------------------------------------------------------------- 19
Spinner Assemblies ---------------------------------------------------------------------------------------------------------- 20-24
Rear & Side Extension Diverter ----------------------------------------------------------------------------------------------- 25
Winch Assembly ----------------------------------------------------------------------------------------------------------------- 26
Airport Spinner Assembly--------------------------------------------------------------------------------------------------- 27-28
Drag Chain Assemblies --------------------------------------------------------------------------------------------------------- 29
Belt Over Chain Assemblies --------------------------------------------------------------------------------------------------- 30
Floor Drawing & Parts List ------------------------------------------------------------------------------------------------- 31-32
Gearboxes --------------------------------------------------------------------------------------------------------------------- 33-36
I-Beam and Screen Weldments ------------------------------------------------------------------------------------------- 37-39
Inverted-Vee Assembly ---------------------------------------------------------------------------------------------------------- 40
Grease Extension Assembly -------------------------------------------------------------------------------------------------- 41
Rear Take-up ---------------------------------------------------------------------------------------------------------------------- 42
Cabshields ------------------------------------------------------------------------------------------------------------------------- 43
Spillshields ------------------------------------------------------------------------------------------------------------------------- 44
Catwalks --------------------------------------------------------------------------------------------------------------------------- 45
Side Skirts ------------------------------------------------------------------------------------------------------------------------- 46
Extended Ladder Assembly ---------------------------------------------------------------------------------------------------- 47
Lights --------------------------------------------------------------------------------------------------------------------------- 48-49
Vibrator ----------------------------------------------------------------------------------------------------------------------------- 50
Channel Spacer ------------------------------------------------------------------------------------------------------------------- 51
Serial Number Decal Information ---------------------------------------------------------------------------------------------- 52
Warranty --------------------------------------------------------------------------------------------------------------- Back Cove r
4
PAGE 4
CONTROL AND HYDRAULIC SYSTEM SPECIFICATION
•
Hydraulic Oil...........................................Good Grade of MS10W Hydraulic
Oil which has wear, oxidation and
foam inhibitors.
•
Oil Filter....................................................10 Micron Element Return Line
•
Relief Valve Setting..............................................................................1500 PSI
•
Oil Flow..............................................................Conveyor (A-Port) 0-15 GPM
Spinner (S-Port) 0-7 GPM
5
PAGE 5
T P
A
S
CONTROL HYDRAULICS INSTALLATION
(Continued)
PAGE 6
6
CONTROL HYDRAULICS INSTALLATION
(Continued)
1. Hydraulic components should be kept as clean as possible during assembly operations.
2. Galvanized pipe and pipe fittings must not be used because flaking of galvanizing material can cause damage to major hydraulic components.
3. A pipe joint sealant, compatible with hydraulic oil, must be applied to all screwed fittings. (Teflon tape is not recommended.)
4. Sufficient hose should be allowed for raising dump body without kinking or stretching hose.
5. Hose should be protected where severe wear may be caused by vibration or sliding movement.
6. Long runs of hose should be supported by nylon ties or clamping.
7. (Auger, Spinner)
Pressure and return hoses, connected to spinner or conveyor motors, may be reversed for proper motor rotation.
8. Three hose lines to rear of truck may be installed inside truck frame, under dump body floor, and secured in place.
9. Use hose manufacturers recommendations for fitting reusable hose ends.
•
Standard pump, valve, tank and hose kits make up the complete system.
*
Swivel adapters are included in kits when “screw-on” type reusable hose ends are furnished.
•
This diagram is Swenson Spreader Company’s complete recommended hydraulic system.
•
This diagram may be used to install an entire system, or part of a system, depending upon kits supplied, and existing components on truck.
•
Alternate proven methods and components are acceptable to suit various truck model requirements.
7
PAGE 7
INSTALLATION AND LIGHT BAR WIRING DIAGRAM
(If Furnished)
S/T/T S/T/T
FLASHER-AMBER
STROBE -AMBER
BACKUP-CLEAR
S/T/T S/T/T
FLASHER-AMBER
STROBE -AMBER
BACKUP-CLEAR
8
PAGE 8
V-BOX INSTALLATION INSTRUCTIONS
THE MODEL EV SERIES SPREADER IS INTENDED TO BE INSTALLED ON
A STANDARD 34” WIDE TRUCK CHASSIS, OR MAY BE INSTALLED
INSIDE AN APPROPRIATE LENGTH DUMP BODY. THE FOLLOWING
METHODS CAN BE USED AS A GUIDE FOR EITHER TYPE OF
INSTALLATION.
5. A portion of some hopper side supports may have to be cut out to clear the vehicle tires. If this is necessary, do not cut out any more than is required. Also, when the formed flange is removed, it is important that a new flange be fitted and welded to conform to the cutout portion.
INSTALLATION ON TRUCK CHASSIS: (Refer to page 10 for illustration.)
INSTALLATION IN DUMP BODY:
1. Remove and store dump body tailgate.
1. It is recommended that at least two mounting angles be located on each side of truck frame. The mounting angles should be located approximately at the front and rear of hopper. Exact placement may vary from left side to right side due to obstructions on truck frame. Mounting hardware kits are available for truck chassis mount installations. For 8 ft. through 11 ft. V-Boxes order PART NO. 00001-086-00. For 12 ft. through 22 ft. V-Boxes order
PART NO. 00001-085-00.
2. Install V-Box centered between dump body sides and as far forward as possible. Longitudinals must overhang rear at least 20” for spinner, and 24” if optional ladder is installed. If dump body floor is not flat, it is suggested the V-Box be placed on two 1” x 6” hardwood boards. This will evenly distribute weight of the loaded
V-Box on dump body floor.
3. Four optional tie down bolts (two each side ) are hooked into holes in upper ends of body side supports. Tie down hooks are hooked under rail of the dump body and nut and jam nut tightened.
2. Mounting angles should be bolted to the vehicle frame. Drill holes only in the frame web; drilling holes in the frame flanges will weaken the frame. DO NOT WELD MOUNTING ANGLES TO THE TRUCK FRAME.
Doing so can cause fatigue cracking of the truck frame.
3. Hardwood wearstrips, usually 1” x 3” (not furnished), may be fitted to the vehicle frame. Mark rivet head locations on the strips and counterbore just deeply enough for clearance. Secure wearstrips in place at each end.
4. The hopper should be positioned on the wooden wearstrips so that a distance of approximately 6” be left between the vehicle cab and the front of the hopper. This will facilitate future servicing of the conveyor chain.
9
PAGE 9
V-BOX INSTALLATION INSTRUCTIONS
10
PAGE 10
Item
3
4
1
2
PARTS LIST FOR TRUCK CHASIS MOUNT
MOUNTING HARDWARE
Part Number Qty. Description
00104-538-00 A/N Frame Pad
00104-017-00 A/N Hold Down Bracket
04003-005-04 A/N Bolt, 1/2” x 1 1/2” H.H. Gr. 5
04003-007-02 A/N Bolt, 3/4” x 3 1/2” H.H. Gr. 5
A/N = AS NEEDED
TAILGATE LATCH INSTALLATION INSTRUCTIONS
1. Install V-Box in truck and position to where you want it.
2. Hold tailgate latch angle and latch pins in proper positions to engage body tailgate latches and weld angle in (4) places as shown. Weld latch pins complete.
3. Use appropriate welding materials and procedures to weld mild steel to stainless steel.
11
PAGE 11
SPINNER INSTALLATION INSTRUCTIONS
1. Using long bent pins and hairpin keepers, assemble spinner upper section to longitudinal brackets.
2. Position lower section inside upper section and temporarily support.
3. Select height adjustment holes which will most closely position spinner disc
18” above road surface.
4. Position holes in lower section to selected holes in upper section, and assemble hardware.
5. Connect hydraulic hoses to spinner motor making sure spinner disc rotates in counter clockwise rotation (as viewed from top of spinner).
12
PAGE 12
OPERATING INSTRUCTIONS
DANGER!
1. WHEN STARTING UP NEW EQUIPMENT, BE SURE EVERYONE IS
STANDING CLEAR, WATCH FOR ANYTHING THAT MAY REQUIRE
SHUTTING SYSTEM DOWN. EQUIPMENT MUST BE STARTED UP
SLOWLY AND WATCHED FROM A SAFE DISTANCE. WATCH FOR
ANYTHING THAT MAY BE HITTING SOMETHING THAT IT SHOULD
NOT BE HITTING, AND LISTEN FOR SOUNDS THAT ARE ABNORMAL.
CORRECT ANYTHING THAT IS ABNORMAL BEFORE CONTINUING USE
OF EQUIPMENT.
4. Keep Conveyor and spinner knobs on valve in closed position.
5. Engage PTO and allow hydraulic oil to circulate several minutes to warm up.
6. Open both valve knobs to first position.
7. Move valve ON-OFF lever to “ON” position.
2. BEFORE WORKING IN OR AROUND SPREADING EQUIPMENT,
HYDRAULIC CONTROL VALVE LEVER MUST BE IN “OFF” POSITION,
PTO MUST BE DISENGAGED, AND TRUCK ENGINE MUST BE SHUT
OFF.
8. Examine conveyor and spinner to see if they are functioning properly.
(They will be operating slowly.) Spinner should turn in CCW rotation as viewed from above spinner. Conveyor should operate rearward.
3. WHEN SPREADER IS REMOVED FROM VEHICLE, OR NOT IN USE,
THE VALVE ON-OFF LEVER SHOULD BE IN THE “OFF” POSITION.
IF LEFT IN “ON” POSITION EXCESSIVE HEAT MAY OCCUR IF
PUMP CONTINUES TO PUMP OIL THROUGH THE HYDRAULIC
VALVE. THIS THEN COULD CAUSE A HOSE TO BURST SPRAYING
HOT OIL ON THOSE NEARBY.
9. Open valve knobs to other positions and check to see if spinner and conveyor operate faster as knobs are opened, and slower as knobs are closed.
10. Turn valve knobs to closed position and move ON-OFF lever to “OFF” position.
4. DURING SPREADER REMOVAL OPERATIONS, THE VALVE ON-OFF
LEVER SHOULD BE IN THE “OFF” POSITION. PTO MUST BE
DISENGAGED AND TRUCK ENGINE MUST BE SHUT OFF.
11. Shut truck engine off.
12. Check entire hydraulic system for leaks.
13. Refill reservoir to three-fourth full.
INITIAL START UP:
1. Fill reservoir about three-fourths full with hydraulic oil. (See page 5 for type.)
KEEP OIL CLEAN.
2. Start truck engine.
14. Hydraulic system is now ready for use.
3. Be sure valve ON-OFF lever is in “OFF” position.
13
PAGE 13
OPERATING INSTRUCTIONS
(Continued)
PREPARING SPREADER FOR USE:
1. Position INTERNAL spinner baffles to position # 1 as shown on page 14.
2. Start truck engine and allow hydraulic system to warm up by shutting off spinner and conveyor knobs and moving ON-OFF lever to “ON” position.
3. Move ON-OFF lever to “OFF” position after warming up.
4. Put spreading material in V-Box.
5. Open spinner and conveyor knobs, and move ON-OFF lever to “ON” position. Spread small amount of material to determine placement of material at various spinner and conveyor speeds in this INTERNAL baffle position.
6. Move valve lever to “OFF” position and shut off truck engine.
7. Position INTERNAL spinner baffles to position # 3 as shown on page 14.
8. Start truck engine.
9. Open spinner and conveyor knobs, and move ON-OFF lever to “ON” position.
Spread small amount of material to determine placement of material at various spinner and conveyor speeds in this INTERNAL baffle position.
10. Positioning EXTERNAL spinner baffles in high positions will give a spread pattern that will be wider than if EXTERNAL spinner baffles are in lower positions.
11. To adjust EXTERNAL baffles, slide baffle in direction of compression spring and pivot to desired position. Allow spring to push baffle tab back into desired slot.
12. It should now be visible that various spread patterns can be obtained by placing INTERNAL and EXTERNAL spinner baffles in various positions, and by changing spinner speeds on valve. A spread pattern can be obtained which should satisfy all road surface coverage requirements.
13. It is suggested that the INTERNAL and EXTERNAL baffle positions, and the valve spinner control setting, be recorded for future use.
OPERATING SPREADER:
1. Adjust INTERNAL and EXTERNAL spinner baffles to positions previously determined to give desired spread pattern. For future use, record positions below.
SIDE HANDLE POSITION: ___________________________________
REAR HANDLE POSITION: _________________________________
2. For operating hydraulic system, follow same procedures as for preparing spreader for use.
3. Any valve knob setting changes may be made while truck is in motion.
4. Spinner and conveyor may be stopped at the same time, without changing their valve settings, by moving ON-OFF lever to “OFF” position.
DANGER!
5. When spinner has been swung up into vertical position, vehicle must not be driven anywhere other than in vehicle and salt storage locations.
14
PAGE 14
ADJUSTING INTERNAL SPINNER BAFFLES FOR DESIRED SPREAD PATTERN
15
PAGE 15
RECOMMENDED MAINTENANCE FOR MATERIAL SPREADERS
DANGER!
SERIOUS PERSONAL INJURY CAN RESULT FROM BEING CAUGHT IN AN
OPERATING CONVEYOR, A TURNING SPINNER, OR OTHER OPERATING
TRUCK EQUIPMENT. BEFORE PERFORMING MAINTENANCE OPERATIONS,
PARK VEHICLE ON LEVEL GROUND. SET PARKING BRAKE, SHUT OFF ALL
POWER, AND SHUT OFF TRUCK ENGINE. ALWAYS REPLACE SHIELDS
AND COVERS WHEN MAINTENANCE IS COMPLETE.
1. Maintain a three-fourths full reservoir using high grade non-foaming hydraulic oil. (See page 5.)
2. Avoid getting contaminants in reservoir when filling.
3. Replace filter cartridge with new cartridge at least twice a year and more often if necessary. (If installed, filter condition gauge has red zone indicating when cartridge needs changing.)
4. Clean hydraulic quick disconnects before taking apart or connecting.
5. Protect hydraulic quick disconnects while in use and after taking apart with oily rag or other suitable protection.
6. Conveyor bearings require periodic greasing every 15 hours of use and more frequent greasing during periods of greater use.
7. Gearbox should be checked for proper lubrication level, and SAE 90 gear type lubricant added if necessary.
8. Grease fittings on gearboxes should be greased at same time bearings are greased. CAUTION! Over greasing may cause seal damage.
9. Gearbox vents, when supplied, should be kept open at all times. or damage may result to seals.
10. Drag chain slack should be checked periodically and taken up until distance between centerline of rear sprocket and point where chain contacts lower flange on longitudinal is 8 inches to 20 inches. (See below.)
11. A coating of grease on V-Box drag chain take-up bolt is recommended for easier chain adjustment.
12. Follow engine manufacturers instructions for engine maintenance recommendations.
13. Hosing down and cleaning spreader after each use, and repainting or oiling after each season will greatly prolong spreader life.
14. Spreader should be completely emptied after each use during severe cold weather to prevent conveyor from freezing. If equipment will be set outside.
Chain contacts lower flange.
Centerline of rear sprocket.
16
PAGE 16
CONDITION 1
Pump cavitation recognized by excessive noise.
CAUSE a. Air entering system through suction lines.
b. Suction line kinked, twisted or too long.
c. Inadequate size suction line.
d. Hydraulic oil too heavy.
e. Excessive pump speed. Normal pump speed
1200 to 1500 RPM.
CORRECTION a. Check line from reservoir for possible leaks.
b. Install suction line as short and straight as possible.
c. Increase suction line size.
d. Drain and replace with a lower viscosity nonhydraulic oil.
e. Pump capacity is 16 GPM at 1000 RPM.
Decrease PTO speed accordingly.
HYDRAULIC TROUBLE-SHOOTING CHART
CONDITION 3
Erratic operation of conveyor and/or spinner.
CAUSE a. Low oil level in reservoir.
b. Worn or defective motor.
c. Dirty, worn or defective flow control valve.
d. Plugged filter.
e. Relief valve setting too low.
f. Pump cavitation.
g. Air vent on reservoir tank is blocked.
CORRECTION
a. Fill reservoir to a 3/4 full level.
*b. Repair or replace motor.
*c. Clean, repair or replace flow control valve.
d. Replace filter element and clean filter.
e. Adjust relief valve for 1500 PSI.
f. Refer to CONDITION 1.
g. Clean or replace vent cap to admit atmospheric pressure to inside of tank.
CONDITION 2
Slow operation of conveyor and/or spinner.
CAUSE a. Worn or defective pump.
b. Worn or defective motor.
c. Pump cavitation.
d. Insufficient pump speed.
CORRECTION
*a. Repair or replace pump.
*b. Repair or replace motor.
c. Refer to CONDITION 1.
d. Pump capacity is 16 GPM at 1000 RPM, Increase PTO accordingly.
CONDITION 4
Conveyor and/or spinner will not operate, or operates in wrong direction.
CAUSE a. Quick disconnects are dirty or damaged causing incomplete connection.
b. Hose connections wrong, causing motors to operate in wrong direction.
c. Foreign material in valve compensator section.
CORRECTION a. Clean or replace and properly connect.
b. Refer to plumbing diagram for proper hose connections, and reconnect.
c. Refer to illustration for proper hose connections at motor and reconnect.
d. Remove compensator section and clean.
NOTE: If a motor operates in the wrong direction, reverse hose connections at motor ports (usually easier).
NOTE:
*
Swenson Spreader LLC warranty does not cover unauthorized disassembly of hydraulic pumps, motors, valves or electric components.
17
PAGE 17
3
4
5
8
2
9
1
8
7
6
Item
1
2
5
6
3
4
7
8
9
FEEDGATE ASSEMBLY
Part Number Qty. Description
09052-000-00 1 Weld, Rear Feedgate, Carbon Steel
00107-412-00 1 Weld, Feedgate, Stainless Steel
00105-813-00 1 Weld, Feedgate w/Sealer Carbon Steel
00113-147-00 1 Weld, Feedgate, w/Sealer Stainless Steel
06016-001-00 1 Assembly, Gatejack (L.H.)
06016-004-00 1 Assembly, Gatejack (R.H.)
04003-002-31 2 Bolt, 5/16”-18 X 2” HH, SS
04003-807-15 2 Nut, 5/16”-18 Center Lock, SS
04622-006-00 1 Bearing, U-Joint
00105-810-00 1 Belt, Wiper
00102-859-00 1 Hold Down Strip, CarbonSteel
00102-859-01 1 Hold Down Strip, Stainless Steel
00118-123-01 1 Plate, Longitudinal Cover, Carbon Steel
00118-123-02 1 Plate, Longitudinal Cover, Stainless Steel
04049-332-00 10.5’ Tape, Reflective
18
PAGE 18
6
6
4
1
Item
1A
2A
3A
4A
5A
1B
2B
3B
4B
5B
5
2
3
8 8
10
9
7
8 8
IDLER ASSEMBLY
Part Number Qty. Description
09061-000-00 1 Weld, Shaft Idler 1 1/4” shaft only 09062-000-00
04003-003-26 4 Bolt, 3/8-16 x 1 1/4” HH, SS
04003-806-12 4 Nut, 3/8”-16 Serrated Flange, SS
06022-001-00 1 Sprocket, 6T 1 1/4” Bore
04080-005-00 2 Bearing, 1 1/4”
Item
1C
2C
N/S
3C
4C
5C
Part Number Qty. Description
00117-693-00 1 Weld, Shaft Idler 2” shaft only 00111-237-00
04003-006-11 8 Bolt, 5/8-11 x 2”, SS
04004-001-15 8 Lockwasher, 5/8” Med. Split, SS
04003-801-22 8 Nut, 5/8”-11 Hex SS
04042-031-00 1 Sprocket, 8T 2” Bore
04080-059-00 2 Bearing, 2”
00117-692-00 1 Weld, Shaft Idler 1 1/2” shaft only 00117-690-00
04003-005-24 8 Bolt 1/2-13 X 1 1/2” HH, SS
04003-806-16 8 Nut, 1/2”-13 Serrated Flange, SS
04042-030-00 1 Sprocket, 8T 1 1/2” Bore
04080-047-00 2 Bearing, 1 1/2”
N/S = Not Shown
8
9
6
7
10
50001-003-00 2 Bearing Plate
00102-290-01 2 Take-up Screw, SS
04003-802-10 8 Nut, 3/4”-10 Hex Jam, SS
04091-023-00 2 Compression Spring
00111-713-01 2 Weld, Take-Up Plate, SS
19
PAGE 19
2 9 7
12
4
1
PARTS LIST FOR EV SPINNER
(00001-935-01)
Item Part Number Qty. Description
N/S
4
N/S
N/S
N/S
N/S
N/S
N/S
1
2
00105-373-00 1 Weldment, EV Spinner, Carbon Steel
00106-381-00 1 Weldment, EV Spinner, Stainless Steel
00105-337-00 3 Weldment, Baffle, Carbon Steel
00106-393-00 3 Weldment, Baffle, Stainless Steel
04011-001-02 3 Hairpin Keeper
04101-035-00 1 Motor, Hydraulic
04101-102-02 1 Flange, Mounting (4-Bolt) (Char-Lynn Only)
04101-102-09 1 Seal Kit (Char-Lynn)
04101-035-98 1 Seal Kit (White)
04003-003-01 8 Bolt, 3/8”-16 X 3/4” H.H. Gr. 5 ZP
04004-001-07 8 Lockwasher, 3/8” Med. Split, ZP
06018-000-00 1 Sub-Assembly, Spinner Disc
(Includes: Item 7,8, 9,10,11 & 12)
06012-003-00 1 Spinner, Hub
04003-806-01 16 Nut, 5/16” Serrated Flange, ZP
06008-000-00 1 Spinner Disc
7
8 N/S
9
04622-002-00 1 Disc Only, Poly Spinner (18”)
04622-007-00 1 Disc Only, Poly Spinner (20”)
10 N/S 04003-002-04 4 Bolt, 5/16”-18 X 1” H.H. Gr. 5, ZP
11 N/S 04003-002-02 12 Bolt, 5/16”-18 X 3/4” H. H. Gr. 5, ZP
12
N/S
06009-008-6
00105-479-00
N/S
N/S
N/S
N/S
N/S
N/S
6 Spinner Flite
Sub-Assembly, Polyurethane Spinner (18”)
(Includes: Spinner Disc w/Flite, Hub, and
Hardware.)
04004-001-05 1 Lockwasher, 1/4” Med. Split, ZP
04003-001-11 1 Bolt, 1/4”-20 x 3/4” H.H., SS
04003-002-24 1 Bolt, 5/16”-18 X 1” H.H., SS
00105-343-00 1 Extension, Spinner
04049-044-00 1 Danger, Decal Spinner
04004-002-08 4 Flatwasher, 3/8”, ZP
04003-801-09 4 Nut, 3/8” Hex, ZP
N/S = Not Shown
20
PAGE 20
4
2
3
Item
1
2
3
4
5
Part Number Qty. Description
00105-399-00 1 Weldment, Extension, CS
00108-942-00 1 Weldment, Extension, SS
00105-394-00 2 Hinged, Rod, CS
00105-394-01 2 Hinged, Rod, SS
04011-001-02 2 Hairpin Keeper, CS
04011-001-04 2 Hairpin, Keeper, SS
00118-125-01 2 Bracket, Spinner, CS
00118-125-02 2 Bracket, Spinner, Ss
04049-044-00 1 Decal, Danger
1
1
SPINNER EXTENSIONS
Item
1
Part Number Qty. Description
00001-962-01
00001-962-02
00001-962-61
00001-962-62
Package, Spinner Extension, Carbon Steel
Package, Spinner Extension, Stainless Steel
Package, Spinner Swing-Up Extension, CS
Package, Spinner Swing-Up Extension, SS
21
PAGE 21
9
12
6
10
11
4
3
2
8
5 1
Item
SPINNER ASSEMBLY
BOTTOM MOUNTED
(00118-102XXX)
Part Number Qty. Description
1
2
3
4
04101-035-00 1 Motor, Hydraulic, 2.8 Cubic Inch
04101-039-00 1 Motor, Hydraulic, 4.2 Cubic Inch
04101-117-00 1 Motor, Hydraulic Cross Hole
04101-167-00 1 Motor, 7/8-14 Port
00104-814-00 4 Lug, Hinge, Carbon Steel
00104-814-01 4 Lug, Hinge, Stainless Steel
04003-003-57 2 Bolt, 3/8”-16 x 1 3/4” HH, SS
04003-804-08 2 Locknut, 3/8”-16 Nylon Insert, SS
22
8
7
Item
5
6
7
Part Number Qty Description
00109-447-00 1 Disc, Spinner 20”, Carbon Steel
00109-074-00 1 Disc, Spinner 20”, Stainless Steel
04622-007-00 1 Disc, Spinner 20”, Poly
06009-008-00 6 Flite, Spinner, Carbon Steel
06009-009-00 6 Flite, Spinner, Stainless Steel
00118-121-01 1 Baffle, Short, Carbon Steel
00118-121-02 1 Baffle, Short, Stainless Steel
8
9
10
11
12
N/S
00118-122-01 2 Baffle, Long, Carbon Steel
00118-122-02 2 Baffle, Long Stainless Steel
06012-003-00 1 Machining, Spinner Hub
04003-002-26 1 Bolt, 5/16-18 X 1 1/4” HH, SS
04004-001-20 1 Lockwasher, 5/16” Med. Split, SS
04091-040-00 3 Spring, Compression, Spinner Baffle
04004-002-25 4 Flatwasher, 5/16” U.S.S., SS
(Needed on Poly Spinners only)
N/S = Not Shown
PAGE 22
14
12
11
13
1
2
3
4
5
Item
1
9
10
3
8 7
4
5
6
SPINNER ASSEMBLY
TOP MOUNTED
(00118-101XXX)
Item
6
7
Part Number Qty. Description
04101-035-00 1 Motor, Hydraulic, 2.8 Cubic Inch
04101-039-00 1 Motor, Hydraulic, 4.2 Cubic Inch
04101-117-00 1 Motor, Hydraulic, Cross Hole
04101-167-00 1 Motor, 7/8-14 Port
00118-121-01
00118-121-02
1 Baffle, Short, Carbon Steel
1 Baffle, Short, Stainless Steel
00118-122-01 2 Baffle, Long, Carbon Steel
00118-122-02 2 Baffle, Long, Stainless Steel
00109-218-00 1 Weld, Spinner Hub
04003-002-49 1 Bolt, 5/16”-18 X 4” HH, Stainless Steel (PolyDisc)
04003-002-48 1 Bolt, 5/16”-18 X 3 1/2” HH, Stainless Steel(Metal Disc)
8
9
10
11
12
13
14
N/S
2
Part Number Qty. Description
04004-001-20 1 Lockwasher, 5/16” Medium Split, Stainless Steel
00105-505-00 1 Disc, Spinner 20” Carbon Steel
00109-074-00 1 Disc, Spinner 20” Stainless Steel
04622-007-00 1 Disc, Spinner 20” Poly
06009-008-00 6 Flite, Spinner, Carbon Steel
06009-009-00 6 Flite, Spinner, Stainless Steel
06020-000-00 .83 Ft. Wire, Safety
04006-008-03 1 Setscrew, 3/8” X 1” Sq. Head
04010-003-02 2 Pin, 1/8” X 1” Cotter
04091-028-00 2 Spring, Compression
04004-002-10 2 Flatwasher, 1/2” U.S.S., ZP
04091-040-00 3 Spring, Compression (In hardware bag.)
04004-002-25 5 Flatwasher, 5/16” U.S.S., SS
(Needed on Poly Spinners Only)
NS - Not Shown
23
PAGE 23
4
5
13.5”
25.5”
5
1
STANDARD SPINNER
(00118-103-XX)
2
3
24
Item
1
1
2
3
4
5
1
LONG SPINNER
(00118-104-XX)
Part Number Qty. Description
00118-129-01 1 Weld, Extension Std., 10 Ga., Carbon Steel
00118-129-02 1 Weld, Extension Std., 10 Ga., Stainless Steel
00118-129-03 1 Weld, Extension Std., 12 Ga., Carbon Steel
00118-129-04 1 Weld, Extension Std., 12 Ga., Stainless Steel
00118-130-01 1 Weld, Extension Long, 10 Ga., Carbon Steel
00118-130-02 1 Weld, Extension Long, 10 Ga., Stainless Steel
00118-130-03 1 Weld, Extension Long, 12 Ga., Carbon Steel
00118-130-04 1 Weld, Extension Long, 12 Ga., Stainless Steel
00118-125-01 2 Bracket, Spinner Holder, Carbon Steel
00118-125-02 2 Bracket, Spinner Holder, Stainless Steel
00105-394-00 2 Rod, Hinge, Carbon Steel
00105-394-01 2 Rod, Hinge, Stainless Steel
04011-001-02 2 Keeper, Hairpin Large, Carbon Steel
04011-001-04 2 Keeper, Hairpin Large, Stainless Steel
04049-044-00 1 Decal, Danger Spinner
PAGE 24
EXTENSION REAR DIVERTER
(00118-105-XX)
4
2
3
4
2
1
3
1
5
6
6
5
7
2
3
4
5
6
Item
1
Part Number Qty Description
00118-136-01
00118-136-02
00118-136-03
00118-136-04
1 Weld, Extension, Rear Diverter, 10G Carbon Steel
1 Weld, Extension, Rear Diverter, 10G Stainless Steel
1 Weld, Extension, Rear Diverter, 12G Carbon Steel
1 Weld, Extension, Rear Diverter, 12G Stainless Steel
00118-125-01
00118-125-02
2 Bracket, Spinner Holder, Carbon Steel
2 Bracket, Spinner Holder, Stainless Steel
00105-394-00 2 Rod, Hinge, Carbon
00105-394-01 2 Rod, Hinge, Stainless Steel
04011-001-01 1 Keeper, Haipin Small, Carbon
04011-001-05 1 Keeper, Hairpin Small, Stainless Steel
04011-001-02 2 Keeper, Hairpin Large, Carbon
04011-001-04 2 Keeper, Hairpin Large, Stainless Steel
04049-044-00 2 Decal, Danger Spinner
3
4
5
EXTENSION RIGHT & LEFT
HAND DIVERTER
(00118-106-XX)
Item Part Number Qty Description
1
2
6
7
00118-140-01 1 Weld, Extension, Side Diverter, 10G Carbon Steel
00118-140-02 1 Weld, Extension, Side Diverter, 10G Stainless Steel
00118-140-03 1 Weld, Extension, SideDiverter, 12G Carbon Steel
00118-140-04 1 Weld, Extension, Side Diverter, 12G Stainless Steel
00118-125-01 2 Bracket, Spinner Holder, Carbon Steel
00118-125-02 2 Bracket, Spinner Holder, Stainless Steel
00105-394-00 2 Rod, HInge Carbon
00105-394-01 2 Rod, HInge, Stainless Steel
04011-001-01 2 Keeper, Hairpin Small, Carbon
04011-001-05 2 Keeper, Hairpin Small, Stainless
04011-001-02 2 Keeper, Hairpin Large, Carbon
04011-001-04 2 Keeper, Hairpin Large, Stainless Steel
04049-044-00 2 Decal, Danger Spinner
00118-171-01 1 Assy, Chute Spinner Extension - Side, Carbon
00118-171-02 1 Assy, Chute Spinner Extension - Side, Stainless Steel
25
PAGE 25
10
11
7
Item
N/S
N/S
N/S
N/S
9
10
11
5
N/S
7
N/S
3
4
1
2
7
WINCH ASSEMBLY
(00112-631-00)
Part Number Qty. Description
00111-422-01 1 Weld, Winch Mounting Bracket, SS
04089-009-00 1 Winch
04003-003-03 4 Bolt, 3/8”-16 X 1” HH GR5, ZP
04003-807-16 4 Locknut, 3/8”
04004-002-08 4 Flatwasher, 3/8”
00119-550-00 1 Add-On, Winch Spinner
00112-653-00 1 Add-on, Cable Assembly
04067-027-00 20 Ft. Wire Rope
04067-029-00 1 Thimble
04067-030-00 3 Clip, Wire Rope
04067-034-00 1 Hook Snap
04003-030-01 2 Bolt, #10-24 X 3/4” Carriage Standard, ZP
00114-936-00 1 Weld, Pulley
04003-001-05 4 Bolt 1/4”-20 X 1” HH GR5,. ZP
04003-806-05 4 Nut, 1/4”-20 Serrated Flange, ZP
N/S = Not Shown
9
26
.
3
4
5
PAGE 26
2
7
7
1
3 5 2 4
9
11
13
N/S
15
16
8
9
11
12
6
7
4
5
Item
1
2
3
17
18
19
20
13 8 17
AIRPORT SPINNER ASSEMBLY
(00118-176-00)
Part Number Qty. Description
00102-905-01 2 Disc, Spinner, S3, 24”
00102-906-00 12 Flite, Spinner
00105-573-00 2 Weld, Spinner Hub
00109-475-00 1 Shield, Anti-Wear
00110-685-00 1 Weld, Deflector/Motor Mounting
04003-003-36 14 Bolt, 3/8”-16 X 1” HH GR 8, ZP
04003-003-37 12 Bolt, 3/8”-16 X 1 1/4” HH GR 8, ZP
04003-003-24 8 Bolt, 3/8”-16 X 3/4” HH, SS
04003-033-03 8 Bolt, 3/8”-16 X 1” Carriage, SS
04003-806-12 32 Nut, 3/8”-16 Serrated Flange, SS
04004-002-20 24 Flatwasher, 3/8” U.S.S. ,SS
04101-035-00 2 Motor, Hudraulic (AA)
04540-007-00 1 Anti-Seize, 1/4 oz. Tube
04004-002-25 7 Flatwasher, 5/16” U.S.S., SS
04003-804-20 7 Locknut, 5/16”-18 Nylon Insert, SS
04105-271-00 1 Divider, Flow
04003-002-32 3 Bolt, 5/16”-18 X 2 1/2” HH, SS
04048-510-06 2 U-Bolt, 5/16” xc 1 3/8”, SS
04110-004-04 4 Elbow, 1/2” 90 Degree
6 7
11 11 6 1
12 12
Item
21
22
23
24
25
26
Part Number Qty. Description
04110-008-04 2 Elbow, 3/4” X 1/2” Reducing
04110-011-01 1 Tee, 1/2” X 1/2” X 3/4”
04110-027-01 4 Nipple, 1/2” Close
04110-028-01 2 Nipple, 3/4” Close
04120-030-05 2 Hose, 1/2” X 19” (2) Wire
04120-030-06 2 Hose, 1/2” X 24” (2) Wire
27
PAGE 27
3
1
2
28
Item
1
2
3
N/S
AIRPORT SPINNER ASSEMBLY
(00105-490-16)
Part Number Qty. Description
00118-176-00 1 Airport Spinner Assemblhy
00118-175-00 1 Weld, Spinner Guard
00110-687-00 1 Weld, Spinner Chute
00118-178-00 1 Hardware Bag
PAGE 28
3
2 4
5
DRAG CHAIN ASSEMBLY
1
Item
6 TOOTH
1
Assy. Number Qty. Description
04045-390-01 1 Weld, Drag Chain, 7 Ft.
04045-390-02 1 Weld, Drag Chain, 8 Ft.
04045-390-03 1 Weld, Drag Chain, 9 Ft.
04045-390-04 1 Weld, Drag Chain, 10 Ft.
04045-390-05 1 Weld, Drag Chain, 11 Ft.
04045-390-06 1 Weld, Drag Chain, 12 Ft.
04045-390-07 1 Weld, Drag Chain, 13 Ft.
04045-390-08 1 Weld, Drag Chain, 14 Ft.
04045-390-09 1 Weld, Drag Chain, 15 Ft.
04045-390-10 1 Weld, Drag Chain, 16 Ft.
04045-390-11 1 Weld, Drag Chain, 17 Ft.
04045-390-12 1 Weld, Drag Chain, 18 Ft.
04045-390-13 1 Weld, Drag Chain, 19 Ft.
04045-390-14 1 Weld, Drag Chain, 20 Ft.
04045-390-15 1 Weld, Drag Chain, 21 Ft.
04045-390-16 1 Weld, Drag Chain, 22 Ft.
8 TOOTH
1 04045-215-00 1 Weld, Drag Chain, 7 Ft.
04045-136-00 1 Weld, Drag Chain, 8 Ft.
04045-076-00 1 Weld, Drag Chain, 9 Ft.
04045-073-00 1 Weld, Drag Chain, 10 Ft.
04045-137-00 1 Weld, Drag Chain, 11 Ft.
04045-077-00 1 Weld, Drag Chain, 12 Ft.
04045-138-00 1 Weld, Drag Chain, 13 Ft.
04045-082-00 1 Weld, Drag Chain, 14 Ft.
04045-139-00 1 Weld, Drag Chain, 15 Ft.
04045-140-00 1 Weld, Drag Chain, 16 Ft.
04045-222-11 1 Weld, Drag Chain, 17 Ft.
04045-222-12 1 Weld, Drag Chain, 18 Ft.
04045-222-13 1 Weld, Drag Chain, 19 Ft.
04045-222-14 1 Weld, Drag Chain, 20 Ft.
04045-222-15 1 Weld, Drag Chain, 21 Ft.
04045-222-16 1 Weld, Drag Chain, 22 Ft.
2
3
4
5
04045-046-00
04045-047-00
Connecting Link only,
Link, w/2 Pins & Cotters
04045-041-00 A/R Drag Chain Bar, w/Links, Pins & Cotter Keys
04045-043-00 A/R Drag Chain Bar w/Links
04045-044-00
04045-048-00
A/R = As Required
2
2
Pin, Master
Key, Cotter
29
PAGE 29
ITEM 1
3 2
ITEM 2
Conveyor Belting Length Assembly No.
6 TOOTH BELT OVER CHAIN
15 Ft.
16 Ft.
17Ft.
18 Ft.
19 Ft.
20 Ft.
21 Ft.
22 Ft.
7 Ft.
8 Ft.
9 Ft.
10 Ft.
11 Ft.
12 Ft.
13 Ft.
14 Ft.
00102-122-10
00102-117-00
00102-118-00
00102-119-00
00102-120-00
00102-121-00
00102-122-00
00102-122-02
00102-122-03
00102-122-01
00102-122-04
00102-122-05
00102-122-06
00102-122-07
00102-122-08
00102-122-09
04076-013-16
04076-013-01
04076-013-02
04076-013-03
04076-013-04
04076-013-05
04076-013-06
04076-013-08
04076-013-09
04076-013-07
04076-013-10
04076-013-11
04076-013-12
04076-013-13
04076-013-14
04076-013-15
BELT OVER CHAIN ASSEMBLY
ITEM 1 ITEM 2 ITEM 3
Length Assembly No.
8 TOOTH BELT OVER CHAIN
Conveyor Belting Conveyor Chain
ITEM 3
Conveyor Chain
04045-070-18
04045-070-01
04045-070-05
04045-070-02
04045-070-03
04045-070-06
04045-070-04
04045-070-10
04045-070-11
04045-070-09
04045-070-12
04045-070-13
04045-070-14
04045-070-15
04045-070-16
04045-070-17
15 Ft.
16 Ft.
17 Ft.
18 Ft.
19 Ft.
20 Ft.
21 Ft.
22 Ft.
7 Ft.
8 Ft.
9 Ft.
10 Ft.
11 Ft.
12 Ft.
13 Ft.
14 Ft.
Item
04045-275-07
04045-275-08
04045-275-09
04045-275-10
04045-275-11
04045-275-12
04045-275-13
04045-275-14
04045-275-15
04045-275-16
04045-275-23
04045-275-24
04045-275-25
04045-275-26
04045-275-21
04045-275-22
Part Number
04076-013-16
04076-013-01
04076-013-02
04076-013-03
04076-013-04
04076-013-05
04076-013-06
04076-013-08
04076-013-09
04076-013-07
04076-013-10
04076-013-11
04076-013-12
04076-013-13
04076-013-14
04076-013-15
Qty. Description
.
N/S
N/S
N/S
00101-806-00 1 Plate, Master Link Cover
04002-311-02 A/R Rivet, #5 x 34” Belt (Copper)
04002-062-03 A/R Screw, 1/4” x 5/8” HWH Type F
N/S = Not Shown
04045-274-07
04045-274-08
04045-274-09
04045-274-10
04045-274-11
04045-274-12
04045-274-13
04045-274-14
04045-274-15
04045-274-16
04045-274-23
04045-274-24
04045-274-25
04045-274-26
04045-274-21
04045-274-22
QUESQYEST
30
PAGE 30
FLOOR PARTS DRAWING
1 3
2
3
31
PAGE 31
4
5
Item
1
PARTS LIST FOR FLOOR
Item Part Number Qty. Description
50001-007-01 1 Floor, 7’ Carbon Steel, 7 Gauge
50001-007-05 1 Floor, 7’ Stainless Steel, 7 Gauge
50001-007-04 1 Floor, 7’ Stainless Steel, 10 Gauge
50001-007-09 1 Floor, 8’ Carbon Steel, 7 Gauge
50001-007-13 1 Floor, 8’ Stainless Steel, 7 Gauge
50001-007-12 1 Floor, 8’ Stainless Steel, 10 Gauge
50001-007-17 1 Floor, 9’ Carbon Steel, 7 Gauge
50001-007-21 1 Floor, 9’ Stainless Steel, 7 Gauge
50001-007-20 1 Floor, 9’ Stainless Steel, 10 Gauge
50001-007-25 1 Floor, 10’ Carbon Steel, 7 Gauge
50001-007-29 1 Floor, 10’ Stainless Steel, 7 Gauge
50001-007-28 1 Floor, 10’ Stainless Steel, 10 Gauge
50007-007-33 1 Floor, 11’ Carbon Steel, 7 Gauge
50007-007-37 1 Floor, 11’ Stainless Steel, 7 Gauge
50007-007-36 1 Floor, 11’ Stainless Steel, 10 Gauge
50001-007-41 1 Floor, 12’ Carbon Steel, 7 Gauge
50001-007-45 1 Floor, 12’ Stainless Steel, 7 Gauge
50001-007-44 1 Floor, 12’ Stainless Steel, 10 Gauge
50001-007-49 1 Floor, 13’ Carbon Steel, 7 Gauge
50001-007-53 1 Floor, 13’ Stainless Steel, 7 Gauge
50001-007-52 1 Floor, 13’ Stainless Steel, 10 Gauge
50001-007-57 1 Floor, 14’ Carbon Steel, 7 Gauge
50001-007-61 1 Floor, 14’ Stainless Steel, 7 Gauge
50001-007-60 1 Floor, 14’ Stainless Steel, 10 Gauge
50001-007-65 1 Floor, 15’ Carbon Steel, 7 Gauge
50001-007-69 1 Floor, 15’ Stainless Steel, 7 Gauge
50001-007-68 1 Floor, 15’ Stainless Steel, 10 Gauge
50001-007-73 1 Floor, 16’ Carbon Steel, 7 Gauge
50001-007-77 1 Floor, 16’ Stainless Steel, 7 Gauge
50001-007-76 1 Floor, 16’ Stainless Steel, 10 Gauge
2
3
4
5
Part Number Qty. Description
50001-007-81 1 Floor, 17’ Carbon Steel, 7 Gauge
50001-007-85 1 Floor, 17’ Stainless Steel, 7 Gauge
50001-007-84 1 Floor, 17’ Stainless Steel, 10 Gauge
50001-007-89 1 Floor, 18’ Carbon Steel, 7 Gauge
50001-007-93 1 Floor, 18’ Stainless Steel, 7 Gauge
50001-007-92 1 Floor, 18’ Stainless Steel, 10 Gauge
50001-007-97 1 Floor, 19’ Carbon Steel, 7 Gauge
50001-007-101 1 Floor, 19’ Stainless Steel, 7 Gauge
50001-007-100 1 Floor, 19’ Stainless Steel, 10 Gauge
50001-007-105 1 Floor, 20’ Carbon Steel, 7, Gauge
50001-007-109 1 Floor, 20’ Stainless Steel, 7 Gauge
50001-007-108 1 Floor, 20’ Stainless Steel, 10 Gauge
50001-007-113 1 Floor, 21’ Carbon Steel, 7 Gauge
50001-007-117 1 Floor, 21’ Stainless Steel, 7 Gauge
50001-007-116 1 Floor, 21’ Stainless Steel, 10 Gauge
50001-007-121 1 Floor, 22’ Carbon Steel, 7 Gauge
50001-007-125 1 Floor, 22’ Stainless Steel, 7 Gauge
50001-007-124 1 Floor, 22’ Stainless Steel, 10 Gauge
50001-010-01 2 Nosepiece, Carbon Steel 6 Tooth Sprocket
50001-010-02 2 Nosepiece, Stainless Steel 6 Tooth Sprocket
50001-010-03 2 Nosepiece, Carbon Steel 8 Tooth Sprocket
50001-010-04 2 Nosepiece, Stainless Steel 8 Tooth Sprocket
04003-018-04 4 Screw, 3/8-16 x 1 1/4” Slotted Flat Head, ZP
04003-018-05 4 Screw, 3/8’16 x 1 1/4” Slotted Flat Head, SS
04003-804-02 4 Locknut, 3/8”-16 Nylon Insert, ZP
04003-804-08 4 Locknut, 3/8”-16 Nylon Insert, SS
04004-002-08 4 Flatwasher, 3/8” U.S.S. ZP
04004-002-20 4 Flatwasher, 3/8” U.S.S. SS
32
PAGE 32
WORM GEARBOX ASSEMBLY
9
8
6
7
5
Item
1
2
6
7
6
3
4
5
Part Number Qty. Description
04132-115-00 1 Gearbox 25:1, 1 1/2” Shaft
04132-119-00 1 Gearbox 50:1, 1 1/2” Shaft
04132-122-00 1 Gearbox 25:1, 2” Shaft
04132-116-00 1 Gearbox 50:1, 2” Shaft
04101-037-00 1 Motor 4-Bolt
04101-101-00 1 Motor, 2-Bolt
04101-131-00 1 Motor, w/Wether-pack Cable & Sensor
04101-124-00 1 Motor, 4-Pin aConnector & Sensor
3
00118-046-00 1 Plate, Bearing
00118-047-00 1 Plate, Gearbox
00102-349-00 1 Machining, Sprocket, 6 tooth
00106-656-00 1 Machining, Sprocket, 8 tooth- 1 1/2” Bore
04007-009-03 2 Set Screw, 3/8-16 X 3/8” Allen Head
04031-004-00 2 Key, 3/8” Sq. X 2” Straight
04007-009-05 2 Set Screw, 3/8”-16 X 1/2” Allen Head
4 2
Item
7
8
9
10
Part Number Qty. Description
04031-020-00 2 Key, 1/2” Sq. X 2 1/2” Straight
04080-047-00 2 Bearings, 1 1/2”
04080-059-00 2 Bearings, 2”
04132-125-00 1 Shaft, 1 1/2”
04132-126-00 1 Shaft, 2”
04132-129-00 1 Snap Rings, Cap, & Key
33
PAGE 33
10
1
Z:\04132-123-00
GEARBOX ASSEMBLY
(04132-123-00 50:1 Hollow Bore)
(04132-124-00 25:1 Hollow Bore)
(See page 33 for Output Shafts)
34
PAGE 34
19
20
21
22
15
16
17
18
23
24
25
26
11
12
13
14
7
8
9
10
Item Part Number Qty. Description
3
4
1
2
5
6
27
28
29
N/S
04132-123-01
04132-123-02
04132-123-03
04132-123-04
04132-123-05
04132-124-05
04132-123-06
1 Housing
1 Cover, Output
1 Endcap
1 Hydraulic, Adapter
1 Shaft, Input Worm, 50:1
1 Shaft, Input Worm, 25:1
1 Gear, Wheel, 50:1
04132-124-06 1 Gear, Wheel, 25:1
04132-123-07 1 Cover, Cap
04132-123-08 2 Bearing, Input Cup
04132-123-09 2 Bearing, Input Cone
04132-123-10 2 Bearing, Output Cup/Cone
04132-116-13 4 Seal, Input
04132-123-12 2 Seal, Output
04132-123-13 1 Coupler
04132-116-19 1 Guard, Shaft
04132-123-15 1 Gasket, Cover
04132-123-16 2 Gasket, Input
04132-116-22 A/R Shim, Input
04132-123-18 A/R Ship, Output
04132-119-24 1 Retaining Ring
04132-116-17 1 Key
04132-116-25 16 Bolt, 3/8”-16 X 1”
04132-116-26 4 Plug, 3/8”-18 NPT
04132-123-23 A/R Plug, 1/8”-27 NPT
04132-116-27 1 Bushing, 3/8”-18 / 1/8”-27
04132-116-28 1 Plug, 5 PSI
04132-123-26 1 Label, 50:1
04132-124-29 1 Label, 25:1
04132-123-27 1 Retaining Ring
04132-123-28 1 Retaining Ring
04132-129-29 1 Key
04132-113-27 A/R Lube, EP 85W140
canimex supplemental file
25
PAGE 35
Note: Please note ratio when service is needed.
SINGLE SPUR GEARBOX ASSEMBLY
5
6 4
9
10
8
Item
1
2
7
8
9
10
5
6
3
4
Part Number Qty. Description
04132-091-00 1 Gearbox, 6:1 Spur
04101-101-00 1 Motor, 2-Bolt
04101-151-00 1 Motor, 2 Bolt w/Weather-pack Cable & Sensor
00118-046-00 2 Plate, Bearing
00103-220-00 1 Machining Sprocket, 8 tooth- 2 Bore
04007-009-05 2 Set Screw, 3/8”-16 x 1/2” Allen Head
04031-020-00 2 Keys, 1/2” Sq. X 2 1/2” Straight
04080-059-00 2 Bearings 2”
00108-953-01 2 Bar, Link, Stainless Steel
04014-005-01 2 Pin, 3/4” X 2” Clevis
04010-004-03 2 Pin, 5/32” x 1 1/4” Cotter
2 1 7 3
35
PAGE 36
TWIN PINION GEAR BOX ASSEMBLY
5
6
Item
1
2
3
8
9
10
11
6
7
4
5
12
13
14
Part Number Qty Description
04132-090-00 1 Gearbox, Twin Pinion 6:1
9,10
12
13
04101-135-00 1 Motor, 2 Bolt
04101-155-00 1 Motor, 2-Bolt, 4-Pin w/Sensor
04101-170-00 1 Motor, 2-Bolt, w/Weather-pack Cable & Sensor
00118-046-00 2 Plate, Bearing
00103-220-00 1 Machining, Sprocket, 8 tooth - 2” Bore
04007-009-05 2 Set Screw, 3/8”-16 X 1/2” Allen Head
04031-020-00 2 Key, 1/2” Sq. X 2 1/2” Straight
04080-059-00 2 Bearing
00108-953-01 2 Bar, Link, Stainless Steel
04014-005-01 2 Pin, 3/4” x 2” Clevis
04010-004-03 2 Pin, 5/32” x 1 1/4” Cotter
04120-003-24 2 Hose, 1/2” X 28”
04110-011-05
04110-027-01
04110-006-04
2 Tee, 3/4” x 1/2” X 1/2” Reducing
2 Nipple, 1/2” Close
2 Elbow, 1/2” 90 Degree Street
8
11
36
PAGE 37
2
14
1 7 3
4
Item
1
Item
1
I-BEAM WELDMENTS 4” RISE
Part Number Qty. Description
00117-961-00
00117-962-00
00117-963-00
00117-964-00
00117-965-00
00117-966-00
00117-967-00
00117-968-00
00117-969-00
00117-970-00
00117-856-00
00117-857-00
00117-858-00
00117-859-00
00117-860-00
Part Number
1 Weld, I-Beam 8’ x 4” Rise Carbon Steel
1 Weld, I-Beam 9’ x 4” Rise Carbon Steel
1 Weld, I-Beam 10’ x 4” Rise Carbon Steel
1 Weld, I-Beam 11’ x 4” Rise Carbon Steel
1 Weld, I-Beam 12’ x 4” Rise Carbon Steel
1 Weld, I-Beam 13’ x 4” Rise Carbon Steel
1 Weld, I-Beam 14’ x 4” Rise Carbon Steel
1 Weld, I-Beam 15’ x 4” Rise Carbon Steel
1 Weld, I-Beam 16’ x 4” Rise Carbon Steel
1 Weld, I-Beam 17’ x 4” Rise Carbon Steel
1 Weld, I-Beam 18’ x 4” Rise Carbon Steel
1 Weld, I-Beam 19’ x 4” Rise Carbon Steel
1 Weld, I-Beam 20’ x 4” Rise Carbon Steel
1 Weld, I-Beam 21’ x 4” Rise Carbon Steel
1 Weld, I-Beam 22’ x 4” Rise Carbon Steel
Qty. Description
00117-971-00
00117-972-00
1 Weld, I-Beam 8’ x 4” Rise Stainless Steel
1 Weld, I-Beam 9’ x 4” Rise Stainless Steel
00117-973-00 1 Weld, I-Beam 10’ x 4” Rise Stainless Steel
00117-974-00 1 Weld, I-Beam 11’ x 4” Rise Stainless Steel
00117-975-00 1 Weld, I-Beam 12’ x 4” Rise Stainless Steel
00117-976-00 1 Weld, I-Beam 13’ x 4” Rise Stainless Steel
00117-977-00 1 Weld, I-Beam 14’ x 4” Rise Stainless Steel
00117-978-00 1 Weld, I-Beam 15’ x 4” Rise Stainless Steel
00117-979-00 1 Weld, I-Beam 16’ x 4” Rise Stainless Steel
00117-980-00 1 Weld, I-Beam 17’ x 4” Rise Stainless Steel
00117-861-00 1 Weld, I-Beam 18’ x 4” Rise Stainless Steel
00117-862-00 1 Weld, I-Beam 19’ x 4” Rise Stainless Steel
00117-863-00 1 Weld, I-Beam 20’ x 4” Rise Stainless Steel
00117-864-00 1 Weld, I-Beam 21’ x 4” Rise Stainless Steel
00117-865-00 1 Weld, I-Beam 22’ x 4” Rise Stainless Steel
A/R - As Required
Item
2
2
1
SCREEN WELDMENTS 4” RISE
(S.D. Standard Duty & H.D. Heavy Duty)
Part Number Qty. Description
4” Rise
00117-801-00 A/R Weld, Screen, S.D. 33.250 x 40.000 Carbon
00117-802-00 A/R Weld, Screen, S.D. 45.250 x 40.000 Carbon
00117-803-00 A/R Weld, Screen, S.D. 33.250 x 41.000 Carbon
00117-804-00 A/R Weld, Screen, S.D. 45.250 x 41.000 Carbon
00117-811-00 A/R Weld, Screen, S.D. 33.250 x 40.000 Stainless
00117-812-00 A/R Weld, Screen, S.D. 45.250 x 40.000 Stainless
00117-813-00 A/R Weld, Screen, S.D. 33.250 x 41.000 Stainless
00117-814-00 A/R Weld, Screen, S.D. 45.250 x 41.000 Stainless
00117-821-00 A/R Weld, Screen, H.D. 33.250 x 40.000 Carbon
00117-822-00 A/R Weld, Screen, H.D. 45.250 x 40.000 Carbon
00117-823-00 A/R Weld, Screen, H.D. 33.250 x 41.000 Carbon
00117-824-00 A/R Weld, Screen, H.D. 45.250 x 41.000 Carbon
00117-831-00 A/R Weld, Screen, H.D. 33.250 x 40.000 Stainless
00117-832-00 A/R Weld, Screen, H.D. 45.250 x 40.000 Stainless
00117-833-00 A/R Weld, Screen, H.D. 33.250 x 41.000 Stainless
00117-834-00 A/R Weld, Screen, H.D. 45.250 x 41.000 Stainless
37
PAGE 38
Item
1
I-BEAM WELDMENTS 14” RISE
Part Number Qty. Description
00117-901-00
00117-902-00
1 Weld, I-Beam 8’ x 14” Rise Carbon Steel
1 Weld, I-Beam 9’ x 14” Rise Carbon Steel
00117-903-00 1 Weld, I-Beam 10’ x 14” Rise Carbon Steel
00117-904-00 1 Weld, I-Beam 11’ x 14” Rise Carbon Steel
00117-905-00 1 Weld, I-Beam 12’ x 14” Rise Carbon Steel
00117-906-00 1 Weld, I-Beam 13’ x 14” Rise Carbon Steel
00117-907-00 1 Weld, I-Beam 14’ x 14” Rise Carbon Steel
00117-908-00 1 Weld, I-Beam 15’ x 14” Rise Carbon Steel
00117-909-00 1 Weld, I-Beam 16’ x 14” Rise Carbon Steel
00117-910-00 1 Weld, I-Beam 17’ x 14” Rise Carbon Steel
00117-911-00
00117-912-00
00117-913-00
00117-914-00
00117-915-00
1
1
1
1
1
Weld, I-Beam 18’ x 14” Rise Carbon Steel
Weld, I-Beam 19’ x 14” Rise Carbon Steel
Weld, I-Beam 20’ x 14” Rise Carbon Steel
Weld, I-Beam 21’ x 14” Rise Carbon Steel
Weld, i-Beam 22’ x 14” Rise Carbon Steel
IItem
1
Part Number Qty Description
00117-931-00
00117-932-00
1 Weld, I-Beam 8’ x 14” Rise Stainless Steel
1 Weld, I-Beam 9’ x 14” Rise Stainless Steel
00117-933-00 1 Weld, I-Beam 10’ x 14” Rise Stainless Steel
00117-934-00 1 Weld, I-Beam 11’ x 14” Rise Stainless Steel
00117-935-00
00117-936-00
00117-937-00
00117-938-00
00117-939-00
00117-940-00
00117-941-00
00117-942-00
00117-943-00
00117-944-00
00117-945-00
1 Weld, I-Beam 12’ x 14” Rise Stainless Steel
1 Weld, I-Beam 13’ x 14” Rise Stainless Steel
1 Weld, I-Beam 14’ x 14” Rise Stainless Steel
1 Weld, I-Beam 15’ x 14” Rise Stainless Steel
1 Weld, I-Beam 16’ x 14” Rise Stainless Steel
1 Weld, I-Beam 17’ x 14” Rise Stainless Steel
1 Weld, I-Beam 18’ x 14” Rise Stainless Steel
1 Weld, I-Beam 19’ x 14” Rise Stainless Steel
1 Weld, I-Beam 20’ x 14” Rise Stainless Steel
1 Weld, I-Beam 21’ x 14” Rise Stainless Steel
1 Weld, I-Beam 22’ x 14” Rise Stainless Steel
A/R = As Required
38
Item
2
1
2
SCREEN WELDMENTS 14” RISE
(S.D. Standard Duty & H.D. Heavy Duty)
Part Number Qty Description
00117-803-00 A/R Weld, Screen, S.D. 33.250 x 41.000 Carbon
00117-804-00 A/R Weld, Screen, S.D. 45.250 x 41.000 Carbon
00117-805-00 A/R Weld, Screen, S.D. 33.250 x 43.000 Carbon
00117-806-00 A/R Weld, Screen, S.D. 45.250 x 43.000 Carbon
00117-813-00 A/R Weld, Screen, S.D. 33.250 x 41.000 Stainless
00117-814-00 A/R Weld, Screen, S.D. 45.250 x 41.000 Stainless
00117-815-00 A/R Weld, Screen, S.D. 33.250 x 43.000 Stainless
00117-816-00 A/R Weld, Screen, S.D. 45.250 x 43.000 Stainless
00117-823-00 A/R Weld, Screen, H.D. 33.250 x 41.000 Carbon
00117-824-00 A/R Weld, Screen, H.D. 45.250 x 41.000 Carbon
00117-825-00 A/R Weld, Screen, H.D. 33.250 x 43.000 Carbon
00117-826-00 A/R Weld, Screen, H.D. 45.250 x 43.000 Carbon
00117-833-00 A/R Weld, Screen, H.D. 33.250 x 41.000 Stainless
00117-834-00 A/R Weld, Screen, H.D. 45.250 x 41.000 Stainless
00117-835-00 A/R Weld, Screen, H.D. 33.250 x 43.000 Stainless
00117-836-00 A/R Weld, Screen, H.D 45.250 x 43.000 Stainless
PAGE 39
Item
1
I-BEAM WELDMENTS 24”RISE
Part Number Qty. Description
00117-916-00 1 Weld, I-Beam 8’ x 24” Rise Carbon Steel
00117-917-00 1 Weld, I-Beam 9’ x 24” Rise Carbon Steel
00117-918-00 1 Weld, I-Beam 10’ x 24” Rise Carbon Steel
00117-919-00 1 Weld, I-Beam 11’ x 24” Rise Carbon Steel
00117-920-00 1 Weld, I-Beam 12’ x 24” Rise Carbon Steel
00117-921-00 1 Weld, I-Beam 13’ x 24” Rise Carbon Steel
00117-922-00 1 Weld, I-Beam 14’ x 24” Rise Carbon Steel
00117-923-00 1 Weld, I-Beam 15’ x 24” Rise Carbon Steel
00117-924-00 1 Weld, I-Beam 16’ x 24” Rise Carbon Steel
00117-925-00 1 Weld, I-Beam 17’ x 24” Rise Carbon Steel
00117-926-00 1 Weld, I-Beam 18’ x 24” Rise Carbon Steel
00117-927-00 1 Weld, I-Beam 19’ x 24” Rise Carbon Steel
00117-928-00 1 Weld, I-Beam 20’ x 24” Rise Carbon Steel
00117-929-00 1 Weld, I-Beam 21’ x 24” Rise Carbon Steel
00117-930-00 1 Weld, I-Beam 22’ x 24” Rise Carbon Steel
Item
1
Part Number Qty. Description
00117-946-00 1 Weld, I-Beam 8’ x 24” Rise Stainless Steel
00117-947-00 1 Weld, I-Beam 9’ x 24” Rise Stainless Steel
00117-948-00 1 Weld, I-Beam 10’ x 24” Rise Stainless Steel
00117-949-00 1 Weld, I-Beam 11’ x 24” Rise Stainless Steel
00117-950-00 1 Weld, I-Beam 12’ x 24” Rise Stainless Steel
00117-951-00 1 Weld, I-Beam 13’ x 24” Rise Stainless Steel
00117-952-00 1 Weld, I-Beam 14’ x 24” Rise Stainless Steel
00117-953-00 1 Weld, I-Beam 15’ x 24” Rise Stainless Steel
00117-954-00 1 Weld, I-Beam 16’ x 24” Rise Stainless Steel
00117-955-00 1 Weld, I-Beam 17’ x 24” Rise Stainless Steel
00117-956-00 1 Weld, I-Beam 18’ x 24” Rise Stainless Steel
00117-957-00 1 Weld, I-Beam 19’ x 24” Rise Stainless Steel
00117-958-00 1 Weld, I-Beam 20’ x 24” Rise Stainless Steel
00117-959-00 1 Weld, I-Beam 21’ x 24” Rise Stainless Steel
00117-960-00 1 Weld, I-Beam 22’ x 24” Rise Stainless Steel
1
2
A/R = As Required
Item
2
SCREEN WELDMENTS 24” RISE
(S.D. Standard Duty & H.D.Heavy Duty)
Part Number Qty. Description
00117-807-00 A/R Weld, Screen, S.D. 33.250 x 46.375 Carbon
00117-808-00 A/R Weld, Screen, S.D. 45.250 x 46.375 Carbon
00117-809-00 A/R Weld, Screen, S.D. 33.250 x 47.375 Carbon
00117-810-00 A/R Weld, Screen, S.D. 45.250 x 47.375 Carbon
00117-817-00 A/R Weld, Screen, S.D. 33.250 x 46.375 Stainless
00117-818-00 A/R Weld, Screen, S.D. 45.250 x 46.375 Stainless
00117-819-00 A/R Weld, Screen, S.D. 33.250 x 47.375 Stainless
00117-820-00 A/R Weld, Screen, S.D. 45.250 x 47.375 Stainless
00117-827-00 A/R Weld, Screen, H.D. 33.250 x 46.375 Carbon
00117-828-00 A/R Weld, Screen, H.D. 45.250 x 46.375 Carbon
00117-829-00 A/R Weld, Screen, H.D. 33.250 x 47.375 Carbon
00117-830-00 A/R Weld, Screen, H.D. 45.250 x 47.375 Carbon
00117-837-00 A/R Weld, Screen, H.D. 33.250 x 46.375 Stainless
00117-838-00 A/R Weld, Screen, H.D. 45.250 x 46.375 Stainless
00117-839-00 A/R Weld, Screen, H.D. 33.250 x 47.375 Stainless
00117-840-00 A/R Weld, Screen, H.D. 45.250 x 47.375 Stainless
39
PAGE 40
3 3
4 4
Item
1
2
3
4
2
1
INVERTED VEE ASSEMBLY
(00106-005-XX)
Part Number Qty. Description
00105-181-00 *2/3 Channel, Inverted “V” Formed, Carbon
00105-181-01 *2/3 Channel, Inverted “V” Formed, Stainless Steel
00106-022-04 1 Sub-Assembly, 7 Ft. Carbon
00106-022-01 1 Sub-Assembly, 10 Ga. 8 & 9 Ft. Carbon
00106-022-02 1 Sub-Assembly, 10 Ga. 10 & 11 Ft. Carbon
00106-022-05 1 Sub-Assembly, 10 Ga. 12 & 13 Ft. Carbon
00106-022-03 1 Sub-Assembly,10 Ga. 14, 15, 16 & 17 Ft. Carbon
00111-309-02
00111-309-01
1 Sub- Assembly, 10 Ga. 18 & 19 Ft. Carbon
1 Sub-Assembly, 10 Ga. 20 - 22 Ft. Carbon
00108-312-04 1 Sub-Assembly, 12 Ga. 7 Ft. Stainless Steel
00108-312-01 1 Sub-Assembly, 12 Ga. 8 & 9 Ft. Stainless Steel
00108-312-02 1 Sub-Assembly, 12 Ga. 10 & 11 Ft. Stainless Steel
00108-312-05 1 Sub-Assembly, 12 Ga. 12 & 13 Ft. Stainless Steel
00108-312-03 1 Sub-Assembly, 12 Ga. 14, 15, 16 & 17 Ft. Stainless Steel
00111-309-05
00111-309-06
1 Sub-Assembly, 12 Ga. 18 & 19 Ft. Stainless Steel
1 Sub-Assembly, 12 Ga. 20 - 22 Ft. Stainless Steel
04003-005-01 *12/18 Bolt, 1/2-13 X 1” HH GR5, ZP
04003-005-17 *12/18 Bolt, 1/2-13 X 1” HH, SS
04003-806-06 *12/18 Nut, 1/2-13 Serrated Flange, ZP
04003-806-16 *12/18 Nut, 1/2-13 Serrated Flange, SS
40
PAGE 41
1
7
3
4
5
6
2
10 9
41
GREASE EXTENSION ASSEMBLY
(00002-404-XX)
Item
5
6
7
N/S
3
4
1
2
9
10
N/S = Not Shown
A/R = As Required
Part Number Qty. Description
00117-768-00 1 Manifold Grease Extension
04002-069-02 A/R Screw, #10-24 x 3/4” HWH Teks/3, SS
04003-003-57 2 Bolt, 3/8”-16 X 1 3/4” HH, SS
04003-806-12 2 Nut, 3/8”-16 Serrated Flange, SS
04121-068-01 6 Stem, 1/8” Paraflex Crimp
04607-024-00 A/R Clamp, Cushioned, 3/8” Loop, SS
04120-047-00 A/R Hose, Grease
04614-001-00 1 Adapter, 1/4”-28 (M) x 1/8” NPT (F)
04015-001-00 3 Fitting, 1/8” NPT Straight Grease
04121-003-01 5 Adapter, 1/8” Swivel
PAGE 42
Item
1
REAR TAKE-UP
Part Number Qty. Description
00102-294-01 1 Pipe, Adjusting, 8 Ft.
00102-294-02 1 Pipe, Adjusting, 9 Ft.
00102-294-03 1 Pipe, Adjusting, 10 Ft.
00102-294-04 1 Pipe, Adjusting, 11 Ft.
00102-294-05 1 Pipe, Adjusting, 12 Ft.
00102-294-06 1 Pipe, Adjusting, 13 Ft.
00102-294-07 1 Pipe, Adjusting, 14 Ft.
00102-294-08 1 Pipe, Adjusting, 15 Ft.
(Continued)
2
3
4
6 5
1
2
42
Item
1
Part Number Qty. Description
00102-294-09 1 Pipe, Adjusting, 16 Ft.
00102-294-10 1 Pipe, Adjusting, 17 Ft.
00102-294-12 1 Pipe, Adjusting, 18 Ft.
00102-294-13 1 Pipe, Adjusting, 19 Ft.
00102-294-14 1 Pipe, Adjusting, 20 Ft
00102-294-15 1 Pipe, Adjusting, 21 Ft.
00102-294-16 1 Pipe, Adjusting, 22 Ft.
4
5
2
3
6
50001-012-02 A/R Bracket, Rear Take-up, SS
04003-002-23 A/R
04003-806-13 A/R
Bolt, 5/16”-18 X 3/4” HH, SS
Nut, 5/16”-18 Serrated Flange, SS
04003-002-21 A/R Bolt, 5/16”-18 X 1 1/2” HH, SS
04003-807-20 A/R Locknut, 5/16”-18 Nylon Insert, SS
A/R= As Required
PAGE 43
1
2
3
4
Item
3
4
1
2
Part Number Qty. Description
00118-162-01
00118-164-01
1 Weldment, Cabshield, Carbon Steel
2 Bracket, Carbon Steel
04003-005-01 8 Bolt, 1/2”-13 X 1” HH, Gr5, ZP
04003-806-03 8 Nut, 1/2”-13 Serrated Flange, ZP
CABSHIELDS
Item
3
4
1
2
Part Number Qty. Description
00118-162-02 1 Weldment, Cabshield, Stainless Steel
00118-164-02 2 Bracket, Stainless Steel
04003-005-17 8 Bolt, 1/2”-13 X 1” HH, SS
04003-806-16 8 Nut, 1/2”-13 Serrated Flange, SS
43
PAGE 44
1
1
2
3
2
3
8”
Item
1
2
3
1
2
3
SPILLSHIELDS (8”, 12”, FRONT & REAR)
8” Carbon
Part Number Qty. Description
00118-153-01 1 Weldment, Spillshield, Carbon Steel
04003-005-01 4 Bolt, 1/2”-13 X 1” HH, Gr5, ZP
04003-806-03 4 Nut, 1/2”-13 Serrated Flange, ZP
Item
1
2
3
12” Carbon
Part Number Qty. Description
00118-154-01 1 Weldment, Spillshield, Carbon Steel
04003-005-01 4 Bolt, 1/2”-13 X 1” HH, Gr5, ZP
04003-806-03 4 Nut, 1/2”-13 Serrated Flange, ZP
00118-153-02 1
8” Stainless
Weldment, Spillshield, Stainless Steel
04003-005-17 4 Bolt, 1/2”-13 x 1” HH, SS
04003-806-16 4 Nut, 1/2”-13 Serrated Flange, SS
1
2
3
12” Stainless
00118-154-02 1 Weldment, Spillshield, Stainless Steel
04003-005-17 4 Bolt, 1/2”-13 x 1” HH, SS
04003-806-16 4 Nut, 1/2”-13 Serrated Flange, SS
44
12”
PAGE 45
3
N/S
N/S
N/S
Item
1
2
CATWALKS
Part Number Qty. Description
00116-230-03
00116-230-04
00116-230-05
00116-230-06
00116-230-07
00116-230-22
00116-230-23
00116-230-24
00116-230-17
00116-230-18
00116-230-19
00116-230-20
00116-230-21
00116-230-28
00116-230-29
00116-230-30
00116-231-03
00116-231-04
00116-231-05
00116-231-06
00116-231-07
00116-231-22
00116-231-23
00116-231-24
00116-231-17
00116-231-18
00116-231-19
00116-231-20
00116-231-21
00116-231-28
00116-231-29
00116-231-30
1 Weld, R.H. Catwalk, 12 Ga. Carbon (8-9 Ft.)
1 Weld, R.H. Catwalk, 12 Ga. Carbon (10-11 Ft.)
1 Weld, R.H. Catwalk, 12 Ga. Carbon 12-13 Ft.)
1 Weld, R.H. Catwalk, 12 Ga. Carbon (14-15 Ft.)
1 Weld, R.H. Catwalk, 12 Ga. Carbon (16-17 Ft.)
1 Weld, R.H. Catwalk, 12 Ga. Carbon (18-19 Ft.)
1 Weld, R.H. Catwalk, 12 Ga. Carbon (20-21 Ft.)
1 Weld, R.H. Catwalk, 12 Ga. Carbon (22 Ft.)
1 Weld, R.H. Catwalk, 10 Ga. SS (8-9 Ft.)
1 Weld, R.H. Catwalk, 10 Ga. SS (10-11 Ft.)
1 Weld, R.H. Catwalk, 10 Ga. SS (12-13 Ft.)
1 Weld, R.H. Catwalk, 10 Ga. SS (14-15 Ft.)
1 Weld, R.H. Catwalk, 10 Ga. SS (16-17 Ft.)
1 Weld, R. H. Catwalk, 10 Ga. SS (18-19 Ft.)
1 Weld, R.H. Catwalk, 10 Ga. SS (20-21 Ft.)
1 Weld, R.H. Catwalk, 10 Ga. SS (22 Ft.)
1 Weld, L.H. Catwalk, 12 Ga. Carbon (8-9 Ft.)
1 Weld, L.H. Catwalk, 12 Ga. Carbon (10-11 Ft.)
1 Weld, L.H. Catwalk, 12 Ga. Carbon (12-13 Ft.)
1 Weld, L.H. Catwalk, 12 Ga. Carbon (14-15 Ft.)
1 Weld, L.H. Catwalk, 12 Ga. Carbon (16-17 Ft.)
1 Weld, L.H. Catwalk, 12 Ga. Carbon (18-19 Ft.)
1 Weld, L.H. Catwalk, 12 Ga. Carbon (20-21 Ft.)
1 Weld, L.H. Catwalk, 12 Ga. Carbon (22 Ft.)
1 Weld, L.H. Catwalk, 10 Ga. SS (8-9 Ft.)
1 Weld, L.H. Catwalk, 10 Ga. SS (10-11 Ft.)
1 Weld, L.H. Catwalk, 10 Ga. SS (12-13 Ft.)
1 Weld, L.H. Catwalk, 10 Ga. SS (14-15 Ft.)
1 Weld, L.H. Catwalk, 10 Ga. SS (16-17 Ft.)
1 Weld, L.H. Catwalk, 10 Ga. SS (18-19 Ft.)
1 Weld, L.H. Catwalk, 10 Ga. SS (20-21 Ft.)
1 Weld, L.H. Catwalk, 10 Ga. SS (22 Ft.)
04049-198-00 A/R Tape, Anti-Slip (Stainless Steel Only)
04003-003-04 A/R Bolt, 3/8”-16 X 1 1/4” H.H. Gr. 5, ZP
04003-003-26 A/R Bolt, 3/8”-16 X 1 1/4” H.H., SS
04003-801-09 A/R Nut, 3/8”-16 Hex, ZP
04003-806-12 A/R Nut, 3/8”-16 Serrated Flange, SS
04004-001-07 A/R Lockwasher, 3/8” Med. Split, ZP(Carbon Only)
45
PAGE 46
3
2 1
1
Item
1
3
4
5
SIDE SKIRTS
(00118-201-xx 24”)
Part Number Qty. Description
04076-094-00 2 Belt, Side Skirt, 8 Ft., 24”
04076-053-00 2 Belt, Side Skirt, 9 Ft. 24”
04076-066-00 2 Belt, Side Skirt, 10 Ft., 24”
04076-069-00 2 Belt, Side Skirt, 11 Ft., 24”
04076-080-00 2 Belt, Side Skirt, 12 Ft., 24”
04076-090-00 2 Belt, Side Skirt, 13 Ft., 24”
04076-068-00 2 Belt, Side Skirt, 14 Ft., 24”
04076-102-00 2 Belt, Side Skirt, 15 Ft., 24”
04073-097-00 2 Belt, Side Skirt, 16 Ft., 24”
04076-123-00 2 Belt, Side Skirt, 17 Ft., 24”
1
46
PAGE 47
2
3
4
5
Item
2
Part Number Qty. Description
04076-118-00 2 Belt, Side Skirt, 18 Ft., 24”
04076-124-00 2 Belt, Side Skirt, 19 Ft., 24”
04076-125-00 2 Belt, Side Skirt, 20 Ft., 24”
04076-126-00 2 Belt, Side Skirt, 21 Ft., 24”
04076-127-00 2 Belt, Side Skirt, 22 Ft., 24”
00118-202-08 2 Bar, Mounting, 8 Ft., Carbon
00118-202-28 2 Bar, Mounting, 8 Ft., Stainless Steel
00118-202-09 2 Bar, Mounting, 9 Ft., Carbon
00118-202-29 2 Bar, Mounting, 9 Ft., Stainless Steel
00118-202-10 2 Bar, Mounting, 10 Ft., Carbon
00118-202-30 2 Bar, Mounting, 10 Ft., Stainless Steel
00118-202-11 2 Bar, Mounting, 11 Ft., Carbon
00118-202-31 2 Bar, Mounting, 11 Ft., Stainless Steel
00118-202-12 2 Bar, Mounting, 12 Ft., Carbon
00118-202-32 2 Bar, Mounting, 12 Ft., Stainless Steel
00118-202-13 2 Bar, Mounting, 13 Ft., Carbon
00118-202-33 2 Bar, Mounting, 13 Ft., Stainless Steel
00118-202-14 2 Bar, Mounting, 14 Ft., Carbon
00118-202-34 2 Bar, Mounting, 14 Ft., Stainless Steel
00118-202-15 2 Bar, Mounting, 15 Ft., Carbon
00118-202-35 2 Bar, Mounting, 15 Ft., Stainless Steel
00118-202-16 2 Bar, Mounting, 16 Ft., Carbon
00118-202-36 2 Bar, Mounting, 16 Ft., Stainless Steel
00118-202-17 2 Bar, Mounting, 17 Ft., Carbon
00118-202-37 2 Bar, Mounting, 17 Ft., Stainless Steel
00118-202-18 2 Bar, Mounting, 18 Ft., Carbon
00118-202-38 2 Bar, Mounting, 18 Ft., Stainless Steel
00118-202-19 2 Bar, Mounting, 19 Ft., Carbon
00118-202-39 2 Bar, Mounting, 19 Ft., Stainless Steel
00118-202-20 2 Bar, Mounting, 20 Ft., Carbon
00118-202-40 2 Bar, Mounting, 20 Ft., Stainless Steel
00118-202-21 2 Bar, Mounting, 21 Ft., Carbon
00118-202-41 2 Bar, Mounting, 21 Ft., Stainless Steel
00118-202-22 2 Bar, Mounting, 22 Ft., Carbon
00118-202-42 2 Bar, Mounting, 22 Ft., Stainless Steel
04003-003-04 A/R Bolt, 3/8”-16 X 1 1/4” H.H. Gr 5, ZP
04003-003-26 A/R Bolt, 3/8”-16 X 1 1/4” H.H., SS
04003-806-02 A/R Nut, 3/8”-16 Serrated Flange, ZP
04003-806-12 A/R Nut, 3/8”-16 Serrated Flange, SS
04004-002-08 A/R Flatwasher, 3/8” U.S.S., ZP
04004-002-20 A/R Flatwasher, 3/8” U.S.S., SS
7
8
9
10
5
6
3
4
20
Item
1
2
16
17
18
19
12
13
14
15
8
9
10
11
Item
1
2
3
6
7
4
5
15
16
17
18
11
12
13
14
19
20
N/S
EXTENDED LADDER ASSEMBLY
Part Number Qty. Description
00118-003-01
00118-004-01
00118-006-01
00118-015-01
00118-018-01
1 Weld, Lower Ladder, Carbon Steel
1 Weld, Ladder Extra Step, Carbon Steel
1 Weld, Ladder Platform, Carbon Steel
1 Latch, Carbon Steel
2 Grab-Tube, Carbon Steel
04003-003-01 4 Bolt, 3/8”-16 X 3/4” HH Gr5, ZP
04003-003-07 2 Bolt, 3/8”-16 x 2” HH Gr5, ZP
04003-003-08 4 Bolt, 3/8”-16 X 2 1/2” HH Gr5, ZP
04003-003-18 1 Bolt, 3/8”-16 X 1 3/4” HH Gr5, ZP
04003-005-01 2 Bolt, 1/2”-13 X 1” HH Gr5, ZP
04003-006-01 4 Bolt, 5/8”-18 X 1 1/2” HH Gr5, ZP
04003-806-02 13 Nut, 3/8”-16 Serrated Flange, ZP
04003-806-03 2 Nut, 1/2”-13 Serrated Flange, ZP
04003-806-04 4 Nut, 5/8”-11 Serrated Flange, ZP
04004-002-08 1 Flatwasher, 3/8” U.S.S., ZP
04004-002-11 2 Flatwasher, 1/2” U.S.S. Plain
04008-002-00 2 Bushing, 1/2” I.D. X 3/4” O.D.
04008-010-00 1 Bushing, Pivot Latch Standoff, SS
04091-041-00 1 Spring, Torsion, SS
04111-003-00 2 Plug, Square 1 1/2”
Part Number Qty. Description
00118-003-02 1 Weld, Lower Ladder, Stainless Steel
00118-004-02 1 Weld, Ladder Extra Step, Stainless Steel
00118-006-02
00118-015-02
1 Weld, Ladder Platform, Stainless Steel
1 Latch, Stainless Steel
00118-018-02 2 Grab-Tube, Stainless Steel
04003-003-24 4 Bolt, 3/8”-16 X 3/4” HH, SS
04003-003-29 2 Bolt, 3/8”-16 x 2” HH, SS
04003-003-21 4 Bolt, 3/8”-16 x 2 1/2” HH, SS
04003-003-57 1 Bolt, 3/8”-16 X 1 3/4” HH, SS
04003-005-17 2 Bolt, 1/2”-13 X 1” HH, SS
04003-006-21 4 Bolt, 5/8”-11 X 1 3/4” HH, SS
04003-806-12 13 Nut, 3/8”-16 Serrated Flange, SS
04003-806-16 2 Nut, 1/2”-13 Serrated Flange, SS
04003-804-09 4 Locknut, 5/8-11 Nylon Insert, Gr5
04004-002-20 1 Flatwasher, 3/8” U.S.S., SS
04004-002-22 2 Flatwasher. 1/2” U.S.S., SS
04008-002-00 2 Bushing, 1/2” I.D. X 3/4” O.D.
04008-010-00 1 Bushing, Pivot Latch Standoff, SS
04091-041-00 1 Spring, Torsion, SS
04111-003-00 2 Plug, Square 1 1/2”00
04004-002-49 4 Flatwasher, 5/8” U.S.S. SS (only used on SS)
2
6
12
8
12
20
1
5
47
PAGE 48
17
3
4
18
9
19
10
13
7
12
11
14
16
15
7
12
2
6
OPTIONAL LIGHTING PACKAGE
1
2
3
4
6
N/S
Item
1
Part Number Qty Description
04605-263-00 1 STT/Tail
04605-264-00 1 STT/Amber Flasher
04605-265-00 1 STT/Amber Strobe
04605-266-00 1 STT/Back-Up
00118-196-00 2 Mounting Bracket, V-Box Height 55” or higher
00118-197-00 2 Mounting Bracket, V-Box Height 54” or Less
04605-211-00 1 Work Light
00118-052-00 1 Mounting Bracket
04607-025-00 2 Cushioned Clamp, 3/4”
04638-009-00 1 Plug, 7 Pin
04638-010-00 1 Receptacle, 7 Pin
N/S = Not Shown
2
3
4
48
PAGE 49
1
2
Item
3
4
1
2
WORKLIGHT
Part Number Qty. Description
04605-211-00 1 Worklight, Sealed Beam
00118-052-00 1 Bracket, Work Light
04003-002-37 2 Bolt, 5/16”-18 X 1” H.H. Stainless Steel
04003-806-13 2 Nut, 5/16”-18 Serrated Flange
49
PAGE 50
3
4
2
4
Item
1
2
1
VIBRATOR
(00002-191-00 Front & 00002-280-00 Side)
Part Number Qty. Description
04150-039-00 2 Vibrator Material - Side
04150-039-00 1 Vibrator Material - Front
00112-050-00 2 Channel, Sides
00114-910-00 1 Channel, Front
3
1 4
50
Item
3
4
N/S
N/S
Part Number Qty. Description
00112-051-00 A/R Plate
04003-005-57 2 Bolt, 1/2”-13 X 5”
04150-040-00 1 Vibrator Mounting Kit (Hardware & Plate)
04150-041-00 1 Vibrator Wiring Kit
PAGE 51
3
2
Item
1
2
CHANNEL SPACER
(00102-436-XX)
Part Number Qty. Description
00115-291-01
00115-291-02
2 Weld, Stabilazer, Carbon
2 Weld, Stabilazer, Stainless Steel
04003-801-14 4 Nut, 1-8 Hex, Carbon
04003-801-23 4 Nut, 1-8 Hex, Stainless Steel
51
PAGE 52
2
1
SERIAL NUMBER DECAL INFORMATION
When ordering parts or requesting information or assistance, always include
the information listed below.
The description, part number and serial number for the spreader is shown on
the serial number decal.
The space below is provided as a convenient place to record these number
just fill in the blanks.
DESCRIPTION ________________________________
PART NUMBER _________________________________
SERIAL NUMBER________________________________
DATE PURCHASED_______________________________
PURCHASED FROM______________________
DEALER’S SERVICE DEPARTMENT PHONE NUMBER
________________________________________________
NOTE: Numbers shown on decal below are for example purposes only.
Refer to decal on spreader for recording information.
127 Walnut Street
Lindenwood, IL 61049
(888) 825-7323
May be covered by one or more of these patents:
3332691 5669531 0 0 0 0
Description:
P, HA, EV-100 10-48, S3, 12G, SPL
Part Number: 00002-392-05
Serial Number:
0203-1008
CALL YOUR AUTHORIZED SWENSON SPREADER DEALER FOR PARTS AND SERVICE
SWENSON SPREADER (815) 393-4455
TOLL FREE (888) 825-7323
FAX (866)310-0300 email: [email protected]
52
PAGE 53
Dealers have the responsibility of calling to the attention of their customers the following warranty prior to acceptance of an order from that customer for any SWENSON® product.
WARRANTY
WHAT THIS WARRANTY COVERS
Swenson Spreader LLC (hereinafter “Swenson”) is committed to assuring Customer satisfaction with the
Spreader (hereinafter "Product"). Swenson warrants to the original owner (hereinafter "Purchaser") of the
Product to be free from defects in material and workmanship for the following term: Swenson warrants ALL
PARTS AND ASSEMBLIES to be free from defects in material and workmanship for a period of one year from the date of purchase. Installation of the Product must be in accordance with Swenson’s instructions. This warranty extends to the Purchaser and may not be assigned without the prior written approval of Swenson; except a distributor may assign this warranty to the first titled owner of the Product.
If a Product has a defect in material or workmanship covered by the warranty, Swenson will (at our option) either replace or repair said part. Swenson’s has sole discretion as to repair of defects covered by this warranty, or replacement of the Product. Swenson’s responsibilities as described herein shall not exceed the amount of the purchase of the Product.
WHAT THIS WARRANTY DOES NOT COVER
Swenson’s warranty does not extend to Product which have been misused, abused, improperly installed, repaired with non-genuine Swenson parts, improperly cared for, if materials such as lava rock or cinders are used, or for which payment has not been made. The warranty is void if repairs or alterations to the Product are made by unauthorized persons, or the Product serial numbers have been altered or defaced.
All gasoline engines and hydraulic pumps are warranted by their manufacturer and not by Swenson Spreader
LLC. Electrical or hydraulic components are not to be disassembled without the express written permission of
Swenson Spreader LLC.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF. THERE IS NO IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SWENSON’S MAXIMUM
OBLIGATION AND LIABILITY UNDER THIS WARRANTY SHALL BE LIMITED TO AN AMOUNT
EQUAL TO THE PRESENT PURCHASE PRICE FOR THE SWENSON PRODUCT. SWENSON SHALL
NOT BE LIABLE FOR ANY LOSS OR DAMAGE, WHETHER DIRECT OR INDIRECT, INCIDENTAL,
CONSEQUENTIAL OR OTHERWISE ARISING OUT OF BREACH OF THIS WRITTEN WARRANTY OR
ANY IMPLIED WARRANTY. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages.
Defective parts returned to Swenson Spreader LLC must be accompanied by the following information:
RGA # ______________
Spreader Model ______________
Serial Number ______________
Date Installed ______________
Where Purchased ______________
Purchaser accepts these terms and warranty limitations unless product is returned within fifteen days for full refund of purchase price.
Effective 4/15/05
PAGE 54
IMPORTANT
INFORMATION
ENCLOSED
SWENSON SPREADER LLC
P.O. BOX 127
LINDENWOOD, ILLINOIS 61049-0127
PHONE: (815)393-4455
TOLL FREE: (888)825-7323
SALES & SERVICE FAX: (866)310-0300 email:[email protected]
website: www.swensonspreader.com
54
PAGE 55

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Hydraulic control system
- Adjustable spread pattern
- Durable construction
- Easy to install and operate