Network Guide
Projector
IN5132/IN5142/IN5134/IN5134a/
IN5144/IN5144a/IN5135/IN5145
User's Manual (detailed)
Network Guide
Thank you for purchasing this product.
This manual only explains the network function of this product. For proper use of
this product, refer to this manual and the other manuals for this product.
WARNING ►Before using this product, be sure to read all manuals for this
product. After reading them, store them in a safe place for future reference.
Features
This projector has a network function that provides you with these features:
üN
etwork Presentation : allows the projector to project computer images transmitted
through a network. (&15)
üW
eb Control : allows you to monitor and control the projector through a network from a
computer. (&16)
üM
y Image : allows the projector to store up to four still images and project them. (&50)
ü Messenger : allows the projector to display text sent from a computer through a network.
(&51)
üN
etwork Bridge : allows you to control an external device through the projector from a
computer. (&52)
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
Trademark acknowledgment
• Microsoft®, Internet Explorer®, Windows®, Windows Vista® and Aero® are registered trademarks
of Microsoft Corporation in the U.S. and/or other countries.
• Adobe® and Flash® are registered trademarks of Adobe Systems Incorporated.
• Pentium® is a registered trademark of Intel Corporation.
• JavaScript® is a registered trademark of Sun Microsystems, Inc.
•H
DMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and other countries.
•C
restron®, Crestron e-Control®, e-Control®, Crestron RoomView® and RoomViewTM are
trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and other
countries.
• Trademark PJLink is a trademark applied for trademark rights in Japan,
the United States of America and other countries and areas.
All other trademarks are the properties of their respective owners.
009-1417-01
1
Contents
Contents

Caution ........................................................................................... 4
1. Connection to the network ....................................................... 5
1.1 System requirements .................................................................................. 5
1.1.1 Required equipment preparation ...................................................................................... 5
1.1.2 Hardware and software requirement for computer ........................................................... 5
1.2 Quick connection ......................................................................................... 6
1.3 Manual network connection setting - Wired LAN -....................................... 7
1.3.1 Equipment connection ...................................................................................................... 7
1.3.2 Network settings ............................................................................................................... 7
1.3.3 “Internet Option” setting .................................................................................................. 10
1.4 Manual network connection setting - Wireless LAN - ................................ 11
1.4.1 Preparation for wireless LAN connection ........................................................................ 11
1.4.2 Wireless LAN connection set up ..................................................................................... 12
2. Network Presentation ............................................................. 15
3. Web Control ............................................................................. 16
3.1 Projector Web Control ................................................................................ 17
3.1.1 Logon .............................................................................................................................. 17
3.1.2 Network Information ........................................................................................................ 18
3.1.3 Network Settings ............................................................................................................. 19
3.1.4 Port Settings ................................................................................................................... 22
3.1.5 Mail Settings ................................................................................................................... 24
3.1.6 Alert Settings ................................................................................................................... 25
3.1.7 Schedule Settings ........................................................................................................... 27
3.1.8 Date/Time Settings .......................................................................................................... 30
3.1.9 Security Settings ............................................................................................................. 32
3.1.10 Projector Control ........................................................................................................... 33
3.1.11 Remote Control ............................................................................................................. 39
3.1.12 Projector Status ............................................................................................................ 41
3.1.13 Network Restart ............................................................................................................ 41
3.2 Crestron e-Control® ................................................................................... 42
3.2.1 Main window .................................................................................................................... 43
3.2.2 Tools window .................................................................................................................... 45
3.2.3 Info window ...................................................................................................................... 47
3.2.4 Help Desk window ............................................................................................................ 48
3.2.5 Emergency Alert ............................................................................................................... 49
4. My Image Function .................................................................. 50
5. Messenger Function ............................................................... 51
2
Contents

6. Network Bridge Function ........................................................ 52
6.1 Connecting devices ...................................................................................
6.2 Communication set up ...............................................................................
6.3 Communication port ..................................................................................
6.4 Transmission method ................................................................................
52
53
53
54
6.4.1 HALF-DUPLEX ............................................................................................................... 54
6.4.2 FULL-DUPLEX ................................................................................................................ 55
7. Other Functions ....................................................................... 56
7.1 E-mail Alerts .............................................................................................. 56
7.2 Projector Management using SNMP ......................................................... 58
7.3 Event Scheduling ...................................................................................... 59
7.4 Command Control via the Network ........................................................... 62
7.5 Crestron RoomView® .................................................................................. 63
8. Troubleshooting ...................................................................... 64
9. Specifications .......................................................................... 65
10. Warranty and after-sales service ......................................... 66
3
Caution
Caution
To use the wireless network function of this projector, you must use the optional
USB wireless adapter which is designated. For precautions according to the standards and laws, refer to the documents that come with the adapter.
[Restrictions on plugging and unplugging the USB wireless adapter]
Before you insert or pull out the USB wireless adapter from the projector, turn off
the power of the projector and pull out the power cord’s plug from the outlet. Do
not touch the USB wireless adapter while it is plugged into the projector and the
projector is receiving AC power.
Do not use extension cables or other devices when connecting the adapter to the projector.
[Security precautions when using wireless LAN]
We recommend setting all security settings, including SSID and ENCRYPTION,
when using wireless LAN communication. If the security settings are not set up,
the data being transmitted may be intercepted or your computer may be accessed
by unauthorized personnel. For details on wireless LAN security settings, refer to
3.1 Projector Web Control or &NETWORK menu in the Operating Guide.
CAUTION ►The optional IEEE802.11b/g/n USB wireless adapter uses
the 2.4GHz radio frequency band. You do not need a radio license to use the
adapter, but you should be aware of the following:
• DO NOT USE NEAR THE FOLLOWING!
• Microwave ovens
• Industrial, scientific or medical devices
• Designated low power radio stations
• Radio station buildings
Using the USB wireless adapter near any of the above may cause radio
interference, which would result in a transmission speed decrease or
communication interruption, and even lead to malfunctioning of devices such
as pacemakers.
•
Depending on the location where the USB wireless adapter is used, radio wave
interference may occur, which may result in a transmission speed decrease or
an interruption in communication. In particular, be aware that using the USB
wireless adapter at locations where there is reinforced steel, other types of
metals or concrete is likely to cause radio wave interference.
•A
vailable Channels
The USB wireless adapter uses the 2.4GHz radio frequency band, but
depending on the country or region you are in, the channels that you can use
might be limited. Consult your dealer for information on the usable channels.
• Bringing the optional USB wireless adapter out of the country or region you
reside in and using it there could lead to a violation of the radio laws of that
country or region.
4
1. Connection to the network
1. Connection to the network
1.1 System requirements
1.1.1 Required equipment preparation
The following equipment is required to connect the projector to your computer
through the network.
■ Common The projector: 1 unit, Computer : minimum 1 set
■ Depending on how you want to connect
1) For the wired connection *1
LAN cable (CAT-5 or greater): 1 piece
2) For the wireless connection *2
- Projector side
IEEE802.11 b/g/n USB wireless adapter (part number: SP-DONGLE-USB) :
1 unit
- Computer side
IEEE802.11 b/g/n wireless LAN equipment: 1 unit for each *3
*1: The system for using the projector's network function requires communication
environment conforming 100Base-TX or 10Base-T.
*2: An access point is required when the wireless LAN connection is used as
Infrastructure mode.
*3: Depending on the type of wireless network device and computer you are
using, the projector may not be able to communicate properly with your
computer, even if the computer has embedded wireless LAN.
To eliminate communication problems, use a Wi-Fi certified wireless network
device.
1.1.2 Hardware and software requirement for computer
To connect your computer to the projector and use the projector's network
function, your computer needs to meet the following requirements:
üO
S: One of the following.
Windows ® XP Home Edition /Professional Edition
Windows Vista ® Home Basic /Home Premium /Business /Ultimate /Enterprise
Windows ® 7 Starter /Home Basic /Home Premium /Professional /Ultimate /
Enterprise
üC
PU: Pentium 4 (2.8 GHz or higher)
üG
raphic card: 16 bit, XGA or higher
* When using "LiveViewer", we recommend that your computer's resolution is
set to 1024 x 768.
üM
emory: 512 MB or higher
üH
ard disk space: 100 MB or higher
üW
eb browser: Internet Explorer ® 6.0 or higher
üC
D-ROM/DVD-ROM drive
5
1. Connection to the network
1.1 System requirements (continued)
NOTE • The network communication control is disabled while the projector
is in standby mode if the STANDBY MODE item is set to SAVING. Set the
STANDBY MODE to NORMAL to set up the network communication to the
projector. (&SETUP menu in the Operating Guide)
• You can get the latest application versions for the projector's network functions
and the latest information for this product from the InFocus website (www.
infocus.com/support).
1.2 Quick connection
"LiveViewer" supports very quick and simple connection to the network.
When using the network function, we recommend that you install "LiveViewer" on
your computer. For details, refer to the "LiveViewer" manual.
In case you don’t want to use "LiveViewer" or you cannot use it by some reason,
follow the manual settings instructions, item 1.3 for the wired LAN (&7) and item
1.4 for the wireless LAN. (&11)
6
1. Connection to the network
1.3 Manual network connection setting - Wired LAN This section explains how to set network connections up manually.
1.3.1 Equipment connection
Connect the projector and a computer with a LAN cable.
* Before connecting with an existing network, contact the network administrator.
Next, check the following computer settings.
1.3.2 Network settings
This provides an explanation of network connection settings for Windows® 7 and
Internet Explorer.
1) Log on to Windows® 7 as an administrator authority. Administrator authority is
the account which can access all functions.
2) Open “Control Panel” from the “Start” menu.
3) Open “View network status and tasks” in “Network and Internet”.
With the icons in the "Control Panel" window displayed, click "Network and
Sharing Center".
4) Click "Change adapter settings" in the menu
on the left side of the "Network and Sharing
Center" window.
(continued on next page)
7
1. Connection to the network
1.3 Manual network connection setting - Wired LAN - (continued)
5) Right-click "Local Area Connection" to open the menu,
and select "Properties".
6) Select "Internet Protocol Version 4 (TCP/IPv4)" and click
[Properties].
7) Select "Use the following IP address" and configure the IP
address, Subnet mask and Default gateway for the computer
accordingly. If a DHCP server exists in the network, you
can select "Obtain an IP address automatically" and the IP
address will be assigned automatically.
After completing the settings, click [OK] to close the window.
(continued on next page)
8
1. Connection to the network
1.3 Manual network connection setting - Wired LAN - (continued)
[About IP address]
■ Setting manually
The Network address portion of the computer and the projector's IP address must
match. In addition, the computer's IP address must be unique from any other
device, including the projector, in the network.
For example:
The projector’s settings are as follows:
IP address: 192.168.1.254
Subnet mask: 255.255.255.0
(Network address: 192.168.1 in this case)
Therefore, specify the computer’s IP address as follows:
IP address: 192.168.1.xxx (xxx shows decimal number.)
Subnet mask: 255.255.255.0
(Network address: 192.168.1 in this case)
Select a number from 1 to 254 for “xxx” which is unique from other equipment.
In this case, since the IP address of the projector is “192.168.1.254”, specify a
setting between 1 to 253 for the computer.
NOTE • “0.0.0.0” cannot be set to the IP address.
• The projector’s IP address can be changed by using the configuration utility
from a web browser. (&21)
• If the projector and the computer exist in the same network (i.e., same
network address), you can leave the default gateway field blank.
• When the projector and the computer exist in different networks, the default
gateway must be set. Consult the network administrator for details.
■ Setting automatically
When a DHCP server exists in the connected network, it is possible to assign an
IP address to the projector and computer automatically.
* DHCP (“Dynamic Host Configuration Protocol”) provides the required network
settings like the IP address from server to client. A server that has DHCP
functionality is called a DHCP server.
(continued on next page)
9
1. Connection to the network
1.3 Manual network connection setting - Wired LAN - (continued)
1.3.3 “Internet Option” setting
1) Click “Internet Options” in the “Network and
Sharing Center” window to open the “Internet
Properties” window.
2) Click the “Connections” tab and then click the [LAN settings]
button to open “Local Area Network (LAN) Settings”.
3) Uncheck all boxes in the “Local Area Network (LAN) Settings”
window.
After completing the settings, click [OK] to close the window.
10
1. Connection to the network
1.4 Manual network connection setting - Wireless LAN Using the optional USB wireless adapter on the projector enables the projector
and computer to communicate in both Ad-Hoc and Infrastructure modes.
This section explains how to set up a wireless LAN connection manually.
1.4.1 Preparation for wireless LAN connection
Fig. 1.4.1.a Without an access point communication (Ad-Hoc)
Fig. 1.4.1.b With an access point communication (Infrastructure)
* Ad-Hoc is a LAN communication method that does not require an access point
to communicate.
* Infrastructure is a LAN communication method that requires an access point to
communicate. If the equipment exists, this mode is most efficient.
If communicating with an existing network, consult with your network
administrator.
First, insert the USB wireless adapter into one of the USB TYPE A ports.
(& Connecting with your devices in the Operating Guide)
Then, set up the computer for wireless communication.
When the computer comes with a built-in IEEE802.11b/g/n wireless LAN device,
enable it and disable other network connections. If a wireless LAN device is not
built into the computer, connect an IEEE802.11b/g/n wireless LAN device and
install the device driver. For details, refer to the computer and the wireless LAN
device's users' guides.
11
1. Connection to the network
1.4 Manual network connection setting - Wireless LAN - (continued)
1.4.2 Wireless LAN connection set up
Using the standard Windows® 7 wireless LAN utility, set up the initial Wireless
LAN settings for the projector as follows:
Connection Control
: Ad-Hoc
SSID
: wireless
Channel
:1
Encryption rating
: None
IP address
: 192.168.10.254
* You can change these settings using your computer's web browser or from the
projector's Network menu. Refer to section 3.1.3 Network Settings (&20) or
NETWORK menu in the Operating Guide.
1) Select "Change adapter settings" from the
menu on the left side of the "Network and
Sharing Center" window.
2) Right-click "Wireless Network Connection" to open the
menu, and select "Properties".
3) Select "Internet Protocol Version 4 (TCP/IPv4)" and click
[Properties].
(continued on next page)
12
1. Connection to the network
1.4 Manual network connection setting - Wireless LAN - (continued)
4) Select "Use the following IP address" and configure the IP
address, Subnet mask and Default gateway for the computer
accordingly.
After completing the settings, click [OK] to close the window.
[About the IP address]
The Network address portion of the IP address setting on your computer and your
projector must match. In addition, the computer's IP address must be unique from
any other device, including the projector, in the network.
For example
The projector’s settings are as follows:
IP address: 192.168.10.254
Subnet mask: 255.255.255.0
(Network address: 192.168.10 in this case)
Therefore, specify the computer’s IP address as follows:
IP address: 192.168.10.xxx (xxx shows decimal number.)
Subnet mask: 255.255.255.0
(Network address: 192.168.10 in this case)
Select a number from 1 to 254 for “xxx” which is unique from other equipment.
In this case, since the IP address of the projector is “192.168.10.254”, specify
a setting between 1 to 253 for the computer.
NOTE • “0.0.0.0” cannot be set to the IP address.
• The projector’s IP address can be changed by using the configuration utility
from a web browser. (&20)
• If the projector and the computer exist in the same network (i.e., same
network address), you can leave the default gateway field blank.
• When the projector and the computer exist in different networks, the default
gateway must be set.
(continued on next page)
13
1. Connection to the network
1.4 Manual network connection setting - Wireless LAN - (continued)
5) Right-click "Wireless Network Connection" to open
the menu, and select "Connect / Disconnect".
6) From the connectable wireless networks, select the SSID of the
projector (set to "wireless" by default), and click [Connect]. If you
have enabled encryption, a window asking for the encryption key
will be displayed. Input the associated encryption key.
7) After connection is established, "Connected" will appear to the
right of SSID.
14
2. Network Presentation
2. Network Presentation
The projector can display or play back computer screen images and audio that
are transmitted through the network. This Network Presentation feature will help
you make presentations and conduct conferences smoothly.
Wireless LAN
Wired LAN
To present over the network, a proprietary software application, "LiveViewer", is
required.
You can download it from the InFocus website (www.infocus.com/support). For
details about this feature, and for instructions to install "LiveViewer", refer to the
"LiveViewer" manual.
To start a Network Presentation, select the LAN port as the input source on the
projector and click the Starting Capture button on "LiveViewer".
"LiveViewer" functions are model dependent. If you want to use the latest version of
"LiveViewer", reference the group item in "LiveViewer" User's Manual. This model is
in the E Group.
NOTE • When the screen resolution of your computer is larger than specified,
the computer image will be shrunk to the size listed below before it is
transferred to the projector:
IN5132, IN5142: 1024 x 768 (XGA)
All other models: 1280 x 800
The transferred image will be displayed smaller on the projected screen even if
the projector resolution is larger than above.
15
3. Web Control
3. Web Control
You can adjust or control the projector via a network from a web browser on a
computer that is connected to the same network.
NOTE • Internet Explorer® 6.0 or later is required.
• If JavaScript® is disabled in your web browser configuration, you must enable
JavaScript® in order to use the projector web pages properly. See the Help files
for your web browser for details on how to enable JavaScript®.
• We recommend that all web browser updates are installed.
• If data is transferred via wireless and wired LAN simultaneously, the projector
may not be able to process the data correctly.
Refer to the following for configuring or controlling the projector from a web
browser.
Make sure that both your computer and projector are connected to the network,
and then open the Web browser.
Enter the projector's IP address into URL input box of the Web browser as per the
example below, and then press the Enter key or
button.
Example: If the IP address of the projector is set to 192.168.1.10:
Enter “http://192.168.1.10/” into the address bar of the web browser
and press the Enter key or click
button.
If the URL is entered correctly and
the projector and your computer
are connected to the same network
correctly, the selection window as
shown on the right will be displayed.
You can choose to use Projector Web
Control or Crestron e-Control® as a tool
for controlling the projector. Click one of
them.
For more details, refer to 3.1 Projector
Web Control (&17) or 3.2 Crestron
e-Control® (&42).
NOTE • Do not attempt to control the projector with the projector's menu or
remote control, and via Web Control simultaneously. Some operational errors
may occur.
• If Crestron e-Control in the Network Settings (&21) is set to Disable, the
selection window above will not appear. The Logon window of the Projector
Web Control will display instead.
• Crestron e-Control® is created using Flash®. You need to install the Adobe®
Flash® Player on your computer to use Crestron e-Control®.
16
3. Web Control
3.1 Projector Web Control
3.1.1 Logon
To use the Projector Web Control function, you need
to logon with your user name and password.
Below are the factory default settings for user
name and password.
User name
Password
Administrator
<blank>
Logon window
Enter your user name and password, and then click the [OK].
If you logon successfully, the following screen will be displayed:
Main menu
Click the desired operation or configuration item on the main menu.
NOTE • The language used on the Projector Web Control screen is the
same as that of the OSD on the projector. If you want to change it, you need
to change the OSD language on the projector. (&SCREEN menu in the
Operating Guide)
17
3. Web Control
3.1 Projector Web Control (continued)
3.1.2 Network Information
Displays the projector’s current network
configuration settings.
Item
Common Information
Projector Name
Wireless Information
Displays the projector name.
Displays the current settings of wireless LAN.
Mode
Displays the wireless LAN communication mode.
DHCP
Displays the DHCP settings.
IP Address
Displays the IP address.
Subnet Mask
Displays the subnet mask.
Default Gateway
Displays the default gateway.
DNS Server Address
Displays the DNS server address.
MAC Address
Displays the MAC address.
Ch
Displays the wireless LAN channel.
Encryption
Displays the data encryption setting.
SSID
Displays the SSID used by the projector.
Speed
Displays the current wireless LAN transmission speed.
Wired Information
18
Description
Displays information common to both wireless and wired
LAN.
Displays the current wired LAN settings.
DHCP
Displays the DHCP setting.
IP Address
Displays the IP address.
Subnet Mask
Displays the subnet mask.
Default Gateway
Displays the default gateway.
DNS Server Address
Displays the DNS server address.
MAC Address
Displays the MAC address.
3. Web Control
3.1 Projector Web Control (continued)
3.1.3 Network Settings
Displays and configures network settings.
Item
Common Setup
Description
Used for configuring settings common to both the wireless and
wired LAN.
Projector Name
Configures the name of the projector.
The Projector Name can be up to 64 alphanumeric
characters. Only letters, numbers and following symbols can
be used.
!"#$%&'()*+,-./:;<=>[email protected][\]^_`{|}~ and space.
A projector name is pre-assigned by default.
sysLocation (SNMP)
Configures the location to be referred to when using SNMP.
The sysLocation can be up to 255 alphanumeric characters.
Only numbers ‘0-9’ and letters ‘a-z’, ‘A-Z’ can be used.
sysContact (SNMP)
Configures the contact information to be referred to when
using SNMP.
The sysContact can be up to 255 alphanumeric characters.
Only numbers ‘0-9’ and letters ‘a-z’, ‘A-Z’ can be used.
AMX D.D.
(AMX Device
Discovery)
Configures the projector's AMX Device Discovery settings
so the projector can be detected by AMX controllers within
the same network. For the details about the AMX Device
Discovery, visit the AMX web site.
URL: http://www.amx.com (as of May 2012)
(continued on next page)
19
3. Web Control
3.1 Projector Web Control - Network Settings (continued)
Item
Wireless Setup
Description
Used for configuring wireless LAN settings.
Mode
Select "Ad-Hoc" or "Infrastructure".
IP Configuration
Configures network settings.
DHCP ON
Enables DHCP.
DHCP OFF
Disables DHCP.
IP Address
Configures the IP address when DHCP is disabled.
Subnet Mask
Configures the subnet mask when DHCP is disabled.
Default
Gateway
Configures the default gateway when DHCP is disabled.
DNS Server Address
Configures the DNS server address.
Select from “1” to “11” a channel to use in the Ad-Hoc mode.
NOTE • Depending on the country where you are
Ch
the channels may vary. In addition, depending on the
country or region where you are may be required to use a
wireless network card that confirm to the standards in the
respective country or region.
Encryption
Select data encryption method.
WEP Key
Input the WEP key.
Either ASCII characters or hexadecimal numbers can be
used during WEP key input. However, you cannot use a
combination of both.The key is defined as follows according
to the WEP and character formats.
Encryption
WEP 64bit
WEP 128bit
HEX numbers
10 characters
26 characters
WPA Passphrase
Input WPA Passphrase.
8 to 63 input characters can be used. Only letters, numbers
and following symbols can be used.
!"#$%&'()*+,-./:;<=>[email protected] [\]^_`{|}~ and space
SSID
Select an SSID from the list.
If you must set your unique SSID, select [Custom], then
set your own SSID following the rules below. Up to 32 input
characters can be used.
Only letters, numbers and following symbols can be used.
!"#$%&'()*+,-./:;<=>[email protected][\]^_`{|}~ and space.
(continued on next page)
20
ASCII characters
5 characters
13 characters
3. Web Control
3.1 Projector Web Control - Network Settings (continued)
Item
Wired Setup
IP Configuration
Description
Used for configuring wired LAN settings.
Configures network settings.
DHCP ON
Enables DHCP.
DHCP OFF
Disables DHCP.
IP Address
Configures the IP address when DHCP is disabled.
Subnet Mask
Configures the subnet mask when DHCP is disabled.
Default
Gateway
Configures the default gateway when DHCP is disabled.
DNS Server Address
Other Setup
Crestron e-Control
Configures the DNS server address.
Configures other network settings.
Set whether or not to use Crestron e-Control®.
If you choose Disable, the Projector Web Control Logon
window (not the selection window) will be initially displayed.
Click the [Apply] button to save the settings.
NOTE • The new configuration settings are activated after restarting the
network connection. When the configuration settings are changed, you must
restart the network connection. You can restart the network connection from
Network Restart on the main menu (&41).
• If you connect the projector to an existing network, consult a network
administrator before setting server addresses.
• The WEP Key, WPA passphrase and SSID settings will not be saved if invalid
characters are used.
• The projector does not allow both wireless and wired LAN to be connected to
the same network. Do not set the same network address for both wireless and
wired LAN.
21
3. Web Control
3.1 Projector Web Control (continued)
3.1.4 Port Settings
Displays and configures communication port
settings.
Item
PJLink TM Port
(Port:4352)
Configures the PJLink TM port (Port:4352).
Port open
Click the [Enable] check box to use port 4352.
Authentication
Click the [Enable] check box when authentication is required
for this port.
My Image Port
(Port:9716)
Configures the My Image Port (Port:9716).
Port open
Click the [Enable] check box to use port 9716.
Authentication
Click the [Enable] check box when authentication is required
for this port.
Messenger Port
(Port:9719)
Configures the Messenger Port (Port:9719).
Port open
Click the [Enable] check box to use port 9719.
Authentication
Click the [Enable] check box when authentication is required
for this port.
(continued on next page)
22
Description
3. Web Control
3.1 Projector Web Control - Port Settings (continued)
Item
SNMP Port
Description
Configures the SNMP port.
Port open
Click the [Enable] check box to use SNMP.
Trap address
Configures the destination of the SNMP Trap in IP format.
• The address allows an IP address or domain name if a
valid DNS server is configured in Network Settings. The
maximum length of the host or domain name is up to 255
characters.
Download MIB file
Downloads a MIB file from the projector.
Network Bridge Port
Port number
Configures the Bridge port number.
Input the port number.
Any number between 1024 and 65535 can be used except
for 41794, 9715, 9716, 9719, 9720, 5900, 5500, and 4352.
By default, it is set to 9717.
Click the [Apply] button to save the settings.
NOTE • The new configuration settings are activated after restarting the
network connection. When the configuration settings are changed, you must
restart the network connection. You can restart the network connection from
Network Restart on the main menu(&41).
23
3. Web Control
3.1 Projector Web Control (continued)
3.1.5 Mail Settings
Displays and configures e-mail addressing
settings.
Item
Description
Send Mail
Click the [Enable] check box to use the e-mail function.
Configure the conditions for sending e-mail under the Alert
Settings.
SMTP Server Address
Configures the address of the mail server in IP format.
• The address allows an IP address or domain name if a valid
DNS server is configured in Network Settings. The host or
domain name can be up to 255 characters.
Sender E-mail address
Configures the sender e-mail address.
The sender e-mail address can be up to 255 alphanumeric
characters.
Configures the e-mail address of up to five recipients. You
can also specify the [TO] or [CC] for each address. The
Recipient E-mail address
recipient e-mail address can be up to 255 alphanumeric
characters.
Click the [Apply] button to save the settings.
NOTE • You can confirm whether the mail settings work correctly using the
[Send Test Mail] button. Enable Send mail setting before clicking the [Send
Test Mail].
• If you connect the projector to an existing network, consult a network
administrator before setting server addresses.
24
3. Web Control
3.1 Projector Web Control (continued)
3.1.6 Alert Settings
Displays and configures failure & alert settings.
Item
Description
Cover Error
The lamp cover is not installed correctly.
Fan Error
The cooling fan is not operating.
Lamp Error
The lamp does not light, and the projector's interior may be
overheated.
Temp Error
The projector's interior may be overheated.
Air Flow Error
The internal temperature is rising.
Cold Error
The projector's interior may be too cold.
Filter Error
The filter must be replaced.
Other Error
Other error.
If this error is displayed, contact your dealer.
Schedule Execution
Error
Schedule Execution error. (&27)
Lamp Time Alarm
The lamp time has expired.
Filter Time Alarm
The filter time has expired.
Filter Status Notification
The details of the air filter status will be displayed.
Transition Detector
Alarm
The projector has been moved. (SECURITY menu in the
Operating Guide)
Cold Start
When the projector is supplied with power, it works as below.
• If STANDBY MODE is set to NORMAL: the projector's power
status changes from “OFF” to “Standby state”.
• If STANDBY MODE is set to SAVING: the projector's power status
changes from “Standby state” to “ON (lamp is turned on)”.
(SETUP menu in the Operating Guide)
Authentication Failure
The SNMP access has been denied.
Refer to Troubleshooting in the Operating Guide for further details on the
errors listed above except for Other Error and Schedule Execution Error.
25
3. Web Control
3.1 Projector Web Control - Alert Settings (continued)
The Alert Items are shown below.
Item
Description
Alarm Time
Configures the Alarm Time parameters.
(Only Lamp Time Alarm and Filter Time Alarm.)
SNMP Trap
Click the [Enable] check box to enable SNMP Trap alerts.
(Except for Schedule Execution Error, Lamp Time Alarm,
Filter Time Alarm, Filter Status Notification and Transition
Detector Alarm.)
Send Mail
Click the [Enable] check box to enable e-mail alerts.
(Except for Cold Start and Authentication Failure.)
Mail Subject
Configures the e-mail subject line to be sent.
The subject line can be up to 100 alphanumeric characters.
(Except Cold Start and Authentication Failure.)
Mail Text
Configures the e-mail text to be sent.
The text can be up to 1024 alphanumeric characters, but
using special characters as per below may shorten this
length.
Special characters " ' : & , % \ and space
(Except Cold Start and Authentication Failure.)
Click the [Apply] button to save the settings.
NOTE • The Filter Error e-mail trigger is dependent on the FILTER
MESSAGE setting in the SERVICE item of the OPTION menu which defines
the period until the filter message is displayed on the projector screen. An
e-mail will be sent when the usage time of the filter exceeds the time limit that is
set. No notification e-mail will be sent if the FILTER MESSAGE is set to TURN
OFF. (OPTION menu in the Operating Guide)
• Lamp Time Alarm defines the threshold for an e-mail notification (reminder)
of the lamp time. When the lamp hours exceed the limit that is configured in the
Projector Web Control, an e-mail will be sent.
• Filter Time Alarm defines the threshold for and e-mail notification (reminder)
of the filter time. When the filter hours exceed the limit that is configured in the
Projector Web Control, an e-mail will be sent.
• Filter Status Notification can be enabled for either or both Status 1 and 2.
These notifications are equivalent to the FILTER indicators on the projector.
(Status 1: off to orange, Status 2: orange to red) Refer to the Operating Guide
for FILTER indicator details.
26
3. Web Control
3.1 Projector Web Control (continued)
3.1.7 Schedule Settings
Displays and configures schedule settings.
Item
Description
Daily
Configures the daily schedule.
Sunday
Configures the Sunday schedule.
Monday
Configures the Monday schedule.
Tuesday
Configures the Tuesday schedule.
Wednesday
Configures the Wednesday schedule.
Thursday
Configures the Thursday schedule.
Friday
Configures the Friday schedule.
Saturday
Configures the Saturday schedule.
Specific date No.1
Configures the specific date (No.1) schedule.
Specific date No.2
Configures the specific date (No.2) schedule.
Specific date No.3
Configures the specific date (No.3) schedule.
Specific date No.4
Configures the specific date (No.4) schedule.
Specific date No.5
Configures the specific date (No.5) schedule.
27
3. Web Control
3.1 Projector Web Control - Schedule Settings (continued)
The schedule settings are shown below.
Item
Description
Schedule
Click the [Enable] check box to enable the schedule.
Date (Month/Day)
Configures the month and date.
This item appears only when Specific date (No. 1-5) is
selected.
Click the [Apply] button to save the settings.
The current event settings are displayed on the schedule list. To add additional
functions and events, configure the following items.
Item
Description
Time
Configures the time to execute commands.
Command
[Parameter]
Configures the commands to be executed.
Power
Configures the parameters for power control.
Input Source
Configures the parameters for input switching.
My Image
Configures the parameters for My Image display. (&50)
Messenger
Configures the parameters for Messenger data display. (&51)
Slideshow
Configures the Start/Stop parameters for the Slideshow.
Click the [Register] button to add new commands to the schedule list.
Click the [Delete] button to delete commands from the schedule list.
Click the [Reset] button to delete all commands and reset the schedule settings
from the schedule list.
28
3. Web Control
3.1 Projector Web Control - Schedule Settings (continued)
NOTE • After the projector is moved, check the date and time set for the
projector before configuring the schedules.
• The internal clock’s time may not remain accurate. Using SNTP is
recommended to maintain accurate time.
• “My Image” and “Messenger” events will not be executed appropriately
but result in a “schedule execution error” when the lamp does not light and/
or display data is not stored in the projector at the scheduled event execution
time.
• “Input Source” and “My Image” events will not be executed if the security
feature is enabled and the projector is locked because of security features.
• Certain projector error states (such as temperature error, lamp error) will
prevent the projector from executing scheduled functions/events.
• If an USB memory device is not detected by the projector or no image for
display exists at the scheduled event time, a schedule execution error will occur
against the scheduled Slideshow event.
• When you start the Slideshow, the input source will automatically switch to
USB TYPE A.
• Image files stored in the root directory of the USB memory device will be
displayed for the scheduled Slideshow.
• Refer to Troubleshooting in the Operating Guide if scheduled functions
or events are not executing properly.
29
3. Web Control
3.1 Projector Web Control (continued)
3.1.8 Date/Time Settings
Displays and configures the date and time
settings.
Item
Description
Current Date
Configures the current date in year/month/day format.
Current Time
Configures the current time in hour:minute:second format.
Daylight Savings Time
Click the [ON] check box to enable daylight savings time and
set the following items.
Configures the date and time when daylight savings time
begins.
Start
Month
Configures the month daylight savings time begins (1~12).
Week
Configures the week of the month daylight savings time
begins (First, 2, 3, 4, Last).
Day
Configures the day of the week daylight savings time begins
(Sun, Mon, Tue, Wed, Thu, Fri, Sat).
Time
hour
Configures the hour daylight savings time begins (0 ~ 23).
minute
Configures the minute daylight savings time begins (0 ~ 59).
End
Configures the date and time daylight savings time ends.
Month
Configures the month daylight savings time ends (1 ~ 12).
Week
Configures the week of the month daylight savings time ends
(First, 2, 3, 4, Last).
Day
Configures the day of the week daylight savings time ends
(Sun, Mon, Tue, Wed, Thu, Fri, Sat).
Time
hour
Configures the hour daylight savings time ends (0 ~ 23).
minute
Configures the minute daylight savings time ends (0 ~ 59).
(continued on next page)
30
3. Web Control
3.1 Projector Web Control - Date/Time Settings (continued)
Item
Description
Time difference
Configures the time difference. Set the same time difference
to match your computer. If unsure, consult your IT manager.
SNTP
Click the [ON] check box to retrieve Date and Time
information from the SNTP server and set the following items.
SNTP Server Address
Configures the SNTP server address in IP format.
• The address allows an IP address or domain name if a valid
DNS server is configured in Network Settings. The host or
domain name can be up to 255 characters.
Cycle
Configures the interval when Date and Time information from
the SNTP server should be retrieved (hour:minute).
Click the [Apply] button to save the settings.
NOTE • The new configuration settings are activated after restarting the
network connection. When the configuration settings change, you must restart
the network connection. You can restart the network connection from Network
Restart on the main menu(&41).
• If you connect the projector to an existing network, consult a network
administrator before setting server addresses.
• Once you turn off AC power or the projector goes into SAVING mode
(&SETUP menu in the Operating Guide), the current date and time setting is
reset.
• To enable the SNTP function, the time difference must be set.
• When SNTP is enabled, the projector will retrieve Date and Time information
from the time server and override other time settings.
• The internal clock’s time may not remain accurate. Using SNTP is
recommended to maintain accurate time.
31
3. Web Control
3.1 Projector Web Control (continued)
3.1.9 Security Settings
Displays and configures passwords and other
security settings.
Item
User Account
Description
Configures the user name and password.
User name
Configures the user name.
The text can be up to 32 alphanumeric characters.
Password
Configures the password.
The text can be up to 255 alphanumeric characters.
Re-enter Password
Reenter the above password for verification.
Network Control
Configures the Authentication password for PJLink™ Port
(Port: 4352), My Image Port (Port: 9716), and Messenger
Port (Port: 9719) (&22, 23).
Authentication
Password
Configures the Authentication password.
The text can be up to 32 alphanumeric characters.
Re-enter
Authentication
Password
Reenter the above password for verification.
SNMP
Community name
Configures the community name if SNMP is used.
Configures the community name. The text can be up to 64
alphanumeric characters.
Click the [Apply] button to save the settings.
NOTE • The new configuration settings are activated after restarting the
network connection. When the configuration settings are changed, you must
restart the network connection. You can restart the network connection from
Network Restart on the main menu(&41).
• Only numbers ‘0-9’ and letters ‘a-z’, ‘A-Z’ can be used.
32
3. Web Control
3.1 Projector Web Control (continued)
3.1.10 Projector Control
The projector can be controlled using the items
on the screen.
The item categories are shown in the main
menu. Most of the items have a submenu. Refer
to the table below for details.
NOTE • The setting values may not match the actual values if the user
changes the value manually. In that case, refresh the page by clicking the
[Refresh] button.
Item
Description
MAIN
POWER
INPUT SOURCE
PICTURE MODE
BLANK ON/OFF
MUTE
FREEZE
Turns the power on/off.
Selects the input source.
Selects the picture mode setting.
Turns the BLANK screen on/off.
Turns the audio mute on/off.
Turns Freeze on/off.
Controls the magnify setting.
MAGNIFY
Some input signal sources may not be able to magnified to
the maximum setting value.
MAGNIFY POSITION V Adjusts the vertical magnify position.
MAGNIFY POSITION H Adjusts the horizontal magnify position.
TEMPLATE
Turns the template on/off.
SHUTTER
Turns the lens shutter on (closed) and off (opened).
ZOOM
Adjusts the zoom setting.
FOCUS
Adjusts the focus setting.
LENS SHIFT V
Adjusts the vertical lens shift.
LENS SHIFT H
Adjusts the horizontal lens shift.
LENS MEMORY
Saves, loads or clears the lens memory data.
PbyP *
Turns the PbyP mode on/off.
PbyP LEFT SOURCE * Selects the source for the PbyP left side area.
PbyP RIGHT SOURCE * Selects the source for the PbyP right side area.
PbyP MAIN AREA *
Selects the PbyP main area position.
MY IMAGE
Selects MY Image.
MY IMAGE DELETE
Deletes MY Image.
(continued on next page) * Only for IN5135 and IN5145.
33
3. Web Control
3.1 Projector Web Control - Projector Control (continued)
Item
PICTURE
BRIGHTNESS
CONTRAST
GAMMA
COLOR TEMP
COLOR
TINT
SHARPNESS
ACTIVE IRIS
MYMEMORY SAVE
MYMEMORY RECALL
IMAGE
ASPECT
OVER SCAN
V POSITION
H POSITION
H PHASE
H SIZE
AUTO ADJUST
EXECUTE
INPUT
PROGRESSIVE
VIDEO NR
COLOR SPACE
COMPONENT
VIDEO FORMAT S-VIDEO
VIDEO FORMAT VIDEO
HDMI FORMAT HDMI 1
HDMI FORMAT HDMI 2
HDMI RANGE HDMI 1
HDMI RANGE HDMI 2
(continued on next page)
34
Description
Adjusts the brightness setting.
Adjusts the contrast setting.
Selects the gamma setting.
Selects the color temperature setting.
Adjusts the color setting.
Adjusts the tint setting.
Adjusts the sharpness setting.
Selects the active iris setting.
Saves the MyMemory data.
Recalls the MyMemory data.
Selects the aspect setting.
Adjusts the over scan setting.
Adjusts the vertical position.
Adjusts the horizontal position.
Adjusts the horizontal phase.
Adjusts the horizontal size.
Automatically adjusts the image.
Selects the progressive setting.
Selects the video noise reduction setting.
Selects the color space.
Selects the COMPONENT port setting.
Selects the s-video format setting.
Selects the video format setting.
Selects the HDMITM format setting of the HDMI 1 port.
Selects the HDMITM format setting of the HDMI 2 port.
Selects the HDMITM range setting of the HDMI 1 port.
Selects the HDMITM range setting of the HDMI 2 port.
3. Web Control
3.1 Projector Web Control - Projector Control (continued)
Item
INPUT (continued)
COMPUTER IN COMPUTER IN1
COMPUTER IN COMPUTER IN2
FRAME LOCK COMPUTER IN1
FRAME LOCK COMPUTER IN2
FRAME LOCK - HDMI 1
FRAME LOCK - HDMI 2
SETUP
AUTO KEYSTONE
EXECUTE
KEYSTONE V
KEYSTONE H
PERFECT FIT
AUTO ECO MODE
ECO MODE
INSTALLATION
STANDBY MODE
MONITOR OUT COMPUTER IN1
MONITOR OUT COMPUTER IN2
MONITOR OUT - LAN
MONITOR OUT USB TYPE A
MONITOR OUT USB TYPE B
MONITOR OUT HDMI 1
MONITOR OUT HDMI 2
MONITOR OUT COMPONENT
MONITOR OUT S-VIDEO
MONITOR OUT - VIDEO
MONITOR OUT STANDBY
Description
Selects the COMPUTER IN1 input signal type.
Selects the COMPUTER IN2 input signal type.
Turns the FRAME LOCK-COMPUTER IN1 function on/off.
Turns the FRAME LOCK-COMPUTER IN2 function on/off.
Turns the FRAME LOCK-HDMI 1 function on/off.
Turns the FRAME LOCK-HDMI 2 function on/off.
Adjusts the keystone distortion automatically.
Adjusts the vertical keystone distortion setting.
Adjusts the horizontal keystone distortion setting.
Adjusts the shape of the projected image at the corners.
Turns on/off the automatic eco mode function.
Selects the eco mode.
Selects the installation status.
Selects the standby mode.
Assigns the MONITOR OUT when the COMPUTER IN1 input
port is selected.
Assigns the MONITOR OUT when the COMPUTER IN2 input
port is selected.
Assigns the MONITOR OUT when the LAN input port is selected.
Assigns the MONITOR OUT when the USB TYPE A input
port is selected.
Assigns the MONITOR OUT when the USB TYPE B input
port is selected.
Assigns the MONITOR OUT when the HDMI 1 input port is
selected.
Assigns the MONITOR OUT when the HDMI 2 input port is
selected.
Assigns the MONITOR OUT when the COMPONENT input
port is selected.
Assigns the MONITOR OUT when the S-VIDEO input port is
selected.
Assigns the MONITOR OUT when the VIDEO input port is selected.
Assigns the MONITOR OUT in the standby mode.
(continued on next page)
35
3. Web Control
3.1 Projector Web Control - Projector Control (continued)
Item
AUDIO
VOLUME
SPEAKER
AUDIO SOURCE COMPUTER IN1
AUDIO SOURCE COMPUTER IN2
AUDIO SOURCE - LAN
AUDIO SOURCE - USB
TYPE A
AUDIO SOURCE - USB
TYPE B
AUDIO SOURCE HDMI 1
AUDIO SOURCE HDMI 2
AUDIO SOURCE COMPONENT
AUDIO SOURCE S-VIDEO
AUDIO SOURCE VIDEO
AUDIO SOURCE AUDIO OUT STANDBY
HDMI AUDIO HDMI 1
HDMI AUDIO HDMI 2
SCREEN
LANGUAGE
MENU POSITION V
MENU POSITION H
BLANK
START UP
MyScreen Lock
MESSAGE
TEMPLATE
C.C. - DISPLAY
C.C. - MODE
C.C. - CHANNEL
(continued on next page)
36
Description
Adjusts the volume setting.
Turns the built-in speaker on/off.
Assigns the AUDIO SOURCE - COMPUTER IN1 input port.
Assigns the AUDIO SOURCE - COMPUTER IN2 input port.
Assigns the AUDIO SOURCE - LAN input port.
Assigns the AUDIO SOURCE - USB TYPE A input port.
Assigns the AUDIO SOURCE - USB TYPE B input port.
Assigns the AUDIO SOURCE - HDMI 1 input port.
Assigns the AUDIO SOURCE - HDMI 2 input port.
Assigns the AUDIO SOURCE - COMPONENT input port.
Assigns the AUDIO SOURCE - S-VIDEO input port.
Assigns the AUDIO SOURCE - VIDEO input port.
Assigns the AUDIO SOURCE in the standby mode.
Selects the HDMITM audio setting of the HDMI 1 port.
Selects the HDMITM audio setting of the HDMI 2 port.
Selects the OSD language.
Adjusts the vertical Menu position.
Adjusts the horizontal Menu position.
Selects the BLANK screen.
Selects the start up screen mode.
Turns MyScreen lock function on/off.
Turns the message function on/off.
Selects the template setting.
Selects Closed Caption DISPLAY setting.
Selects Closed Caption MODE setting.
Selects Closed Caption CHANNEL setting.
3. Web Control
3.1 Projector Web Control - Projector Control (continued)
Item
OPTION
SOURCE SKIP COMPUTER IN1
SOURCE SKIP COMPUTER IN2
SOURCE SKIP - LAN
SOURCE SKIP USB TYPE A
SOURCE SKIP USB TYPE B
SOURCE SKIP HDMI 1
SOURCE SKIP HDMI 2
SOURCE SKIP COMPONENT
SOURCE SKIP S-VIDEO
SOURCE SKIP VIDEO
AUTO SEARCH
AUTO KEYSTONE
DIRECT POWER ON
AUTO POWER OFF
SHUTTER TIMER
USB TYPE B
MY BUTTON-1
MY BUTTON-2
MY BUTTON-3
MY BUTTON-4
SERIAL PORT ECHO
Description
Selects the Source Skip - COMPUTER IN1 setting.
Selects the Source Skip - COMPUTER IN2 setting.
Selects the Source Skip - LAN setting.
Selects the Source Skip - USB TYPE A setting.
Selects the Source Skip - USB TYPE B setting.
Selects the Source Skip - HDMI 1 setting.
Selects the Source Skip - HDMI 2 setting.
Selects the Source Skip - COMPONENT setting.
Selects the Source Skip - S-VIDEO setting.
Selects the Source Skip - VIDEO setting.
Turns the automatic signal search function on/off.
Turns the automatic keystone distortion correction function
on/off.
Turns the direct power on function on/off.
Configures the timer to shut off the projector when no signal
is detected.
Selects the shutter timer setting.
Selects the USB TYPE B setting.
Assigns the functions for the MY BUTTON-1 button on the
remote control.
Assigns the functions for the MY BUTTON-2 button on the
remote control.
Assigns the functions for the MY BUTTON-3 button on the
remote control.
Assigns the functions for the MY BUTTON-4 button on the
remote control.
Controls whether the serial port echoes characters.
(continued on next page)
37
3. Web Control
3.1 Projector Web Control - Projector Control (continued)
Item
OPTION (continued)
REMOTE RECEIV. FRONT
REMOTE RECEIV. REAR
REMOTE FREQ. NORMAL
REMOTE FREQ. HIGH
REMOTE ID
Description
Turns the front IR sensor on/off.
Turns the rear front IR sensor on/off.
Turns the remote control signal frequency normal function
on/off.
Turns the remote control signal frequency high function on/
off.
Selects Remote ID setting.
This item is executed when the button is clicked.
It does not display a confirmation message.
Click the [Quit Presenter Mode].
Item
Description
SERVICE
Quit Presenter Mode
38
Quit compulsorily from the Presenter mode.
3. Web Control
3.1 Projector Web Control (continued)
3.1.11 Remote Control
Remote control functions are assigned in the
Web Remote Control screen.
Do not attempt to control the projector using
both the projector's remote control and the
Web Remote Control simultaneously. Some
operational errors may occur.
Item
Description
STANDBY
Assigned the same operation as the STANDBY button.
ON
Assigned the same operation as the ON button.
COMPUTER IN1
Assigned the same operation as the COMPUTER IN1 button.
COMPUTER IN2
Assigned the same operation as the COMPUTER IN2 button.
LAN
Assigned the same operation as the LAN button.
USB TYPE A
Assigned the same operation as the USB TYPE A button.
USB TYPE B
Assigned the same operation as the USB TYPE B button.
COMPONENT
Assigned the same operation as the COMPONENT button.
S-VIDEO
Assigned the same operation as the S-VIDEO button.
VIDEO
Assigned the same operation as the VIDEO button.
HDMI 1
Assigned the same operation as the HDMI 1 button.
HDMI 2
Assigned the same operation as the HDMI 2 button.
FREEZE
Assigned the same operation as the FREEZE button.
AV MUTE
Assigned the same operation as the AV MUTE button.
▲
Assigned the same operation as the ▲ button.
▼
Assigned the same operation as the ▼ button.
◄
Assigned the same operation as the ◄ button.
►
Assigned the same operation as the ► button.
ENTER
Assigned the same operation as the ENTER button.
MENU
Assigned the same operation as the MENU button.
RESET
Assigned the same operation as the RESET button.
PAGE UP
Assigned the same operation as the PAGE UP button.
PAGE DOWN
Assigned the same operation as the PAGE DOWN button.
SLIDESHOW
Starts the Slideshow.
(continued on next page)
39
3. Web Control
3.1 Projector Web Control - Remote Control (continued)
NOTE • The Web Remote Control does not support repeated functions when
a button is clicked down and held.
• Since the repeat function is not available, click the button repeatedly as many
times as you require.
• Even if you click and hold the button, the Web Remote Control only sends your
request command once. Release the button, and click it again.
• When the [STANDBY] or [ON] button is pushed, a message window comes
up to confirm the operation. To control the power, push [OK], otherwise push
[Cancel].
40
3. Web Control
3.1 Projector Web Control (continued)
3.1.12 Projector Status
Displays the settings and status of the projector.
Item
Description
Error Status
Displays the current error status.
Lamp Time
Displays the current lamp usage time.
Filter Time
Displays the current filter usage time.
Filter Status
Displays the current cleanliness level of the air filter.
Power Status
Displays the current power status.
Input Status
Displays the current input signal source.
Blank On/Off
Displays the current BLANK screen on/off status.
Mute
Displays the current audio mute on/off status.
Freeze
Displays the current Freeze status.
Shutter
Displays the current Shutter status.
3.1.13 Network Restart
Restarts the projector’s network connection.
Item
Restart
Description
Restarts the projector’s network connection in order to
activate new configuration settings.
NOTE • Restarting requires you to re-log on in order to further control or
configure the projector from a web browser. Wait 30 seconds or more after
clicking the [Restart] button to log on again.
41
3. Web Control
3.2 Crestron e-Control®
Tab
The Main window as shown above is
displayed at first. However, if you have
enabled User Password on the Tools window
(&46), a dialog prompting you to enter
the password as shown on the right will be
displayed, and no operation will be enabled
until you have entered the password. After
entering the preset password, the dialog
disappears and the Main window will be
displayed. As shown below, you can open a
window by clicking the corresponding tab at
the top right of the window.
Tab
User Password dialog
Description
®
Logout
Tools
Info
Contact IT Help
Logs out from e-Control .
This tab appears only when User Password of the Tools window is
enabled.
Opens the Tools window (&45).
Opens the Info window (&47).
Opens the Help Desk window (&48).
NOTE • If Crestron e-Control in the Network Settings (&21) is set to
Disable, Crestron e-Control® cannot be used to operate the projector. Enable
Crestron e-Control and close the web browser. Next, restart the web browser
and then enter the projector's IP address.
• Only English is supported on Crestron e-Control®.
• If the connection is terminated, the "Loading..." screen will appear. Check the
connection between the projector and the computer, then return or refresh the
Web page.
42
3. Web Control
®
3.2 Crestron e-Control (continued)
3.2.1 Main window
1
4
2
3
You can operate the projector's basic controls on this screen.
NOTE • If the projector is in the standby mode, only the [Power] button can
be operated.
1 Click a button and operate as follows:
Button
Power
Vol -/ Vol +
Mute
Description
Turns the power on/off.
Adjusts the volume setting.
Turns the audio mute on/off.
2S
ources List
You can click a button to switch the input channel. The cursor will move
according to the currently selected input port.
Button
Computer in1
Computer in2
LAN
USB Type A
USB Type B
HDMI 1
HDMI 2
Component
S-Video
Video
Description
Selects the input from the COMPUTER IN1 port.
Selects the input from the COMPUTER IN2 port.
Selects the input from the LAN port.
Selects the input from the USB TYPE A ports.
Selects the input from the USB TYPE B port.
Selects the input from the HDMI 1 port.
Selects the input from the HDMI 2 port.
Selects the input from the COMPONENT port.
Selects the input from the S-VIDEO port.
Selects the input from the VIDEO port.
43
3. Web Control
3.2 Crestron e-Control® - Main window (continued)
3C
lick a button and operate as follows: To show the hidden buttons, click the ◄ /
► icons at the left and right ends.
Button
Freeze
Contrast
Brightness
Color
Sharpness
Magnify
Auto
Blank
Description
Turns Freeze on/off.
Adjusts the contrast setting.
Adjusts the brightness setting.
Adjusts the color setting.
Adjusts the sharpness setting.
Controls the magnification setting using the [+] / [-] buttons.
Use the [▲] [▼] [◄] [►] buttons to move to the area you want
to magnify.
Adjusts the image automatically.
Turns the BLANK screen on/off.
4C
lick the button and operate in the same way as the bundled remote control.
Button
Menu
Enter
Reset
▲
▼
◄
►
44
Description
Assigned the same operation as the the MENU button.
Assigned the same operation as the ENTER button.
Assigned the same operation as the RESET button.
Assigned the same operation as the ▲ button.
Assigned the same operation as the ▼ button.
Assigned the same operation as the ◄ button.
Assigned the same operation as the ► button.
3. Web Control
®
3.2 Crestron e-Control (continued)
3.2.2 Tools window
2
1
4
5
3
Configures the settings between the projector and Crestron® control system.
Click the [Exit] button to return to the Main window.
NOTE
• Two-byte characters should not be used.
• This window must contain data. It cannot be left blank.
1C
restron Control
Configures the settings of Crestron® control system devices.
Item
IP Address
IP ID
Port
Description
Configures the IP address of the control system.
Configures the IP ID of the control system.
Specifies the port number used for communication by the
control system.
To apply the settings, click the [Send] button.
2 Projector
Configures the network settings of the projector.
Item
Projector Name
Location
Assigned To:
Description
Configures the name of the projector. The Projector Name can
be up to 64 alphanumeric characters.
Configures the location name of the projector. You can specify
a Location name up to 32 alphanumeric characters.
Configures the user name for the projector. You can specify a
user name up to 32 alphanumeric characters.
Support characters include spaces and: !"#$%&'()*+,-./:;<=>[email protected][\]^_`{|}~
To apply the settings, click the [Send] button.
45
3. Web Control
3.2 Crestron e-Control® - Tools window (continued)
3 P
rojector (continued)
Configures the network settings of the projector.
Item
DHCP
IP Address
Description
Enables DHCP.
Configures the IP address when DHCP is disabled.
Subnet Mask
Configures the subnet mask when DHCP is disabled.
Default Gateway
DNS Server
Configures the default gateway when DHCP is disabled.
Configures the DNS server address when DHCP is disabled.
To apply the settings, click the [Send] button.
4U
ser Password
Configures the User Password. To prompt for the entry of User Password before
starting e-Control®, select the checkbox.
Item
New Password
Confirm
Description
Configures the password.
You can specify a password up to 26 alphanumeric characters.
Support characters include spaces and:
!"#$%&'()*+,-./:;<=>[email protected][\]^_`{|}~
Reenter the above password for verification. If the password is
incorrect, an error message is displayed.
To apply the settings, click the [Send] button.
5A
dmin Password
Configures the Admin Password. To prompt for the entry of Admin Password
before displaying the Tools window, select the checkbox.
Item
New Password
Confirm
Description
Configures the password.
You can specify a password up to 26 alphanumeric characters.
Support characters include spaces and:
!"#$%&'()*+,-./:;<=>[email protected][\]^_`{|}~
Reenter the above password for verification. If the password is
incorrect, an error message is displayed.
To apply the settings, click the [Send] button.
46
3. Web Control
®
3.2 Crestron e-Control (continued)
3.2.3 Info window
1
2
Displays the settings and status of the projector.
Click the [Exit] button to return to the Main window.
1P
rojector Information
Item
Projector Name
Location
MAC Address
Resolution
Lamp Hours
Assigned To:
Description
Displays the projector name settings.
Displays the projector's location name.
Displays the projector's wired LAN MAC address.
Displays the resolution and vertical frequency of the signal
input selected on the projector.
Displays the usage time for the current lamp.
Displays the projector's user name.
2P
rojector Status
Item
Description
Power Status
Displays the current power status.
Input Source
Displays the current input signal source.
Picture Mode
Displays the current picture mode setting.
Installation
Displays the current installation setting.
Eco Mode
Displays the current eco mode setting.
Error Status
Displays the current error status.
NOTE • Projector Name, Location and the user name for Assigned To: may
appear truncated if they are too long.
47
3. Web Control
3.2 Crestron e-Control® (continued)
3.2.4 Help Desk window
Sends/receives messages to/from the administrator for Crestron RoomView®
Express.
Button
Send
48
Description
Sends a message.
Check the received message.
3. Web Control
®
3.2 Crestron e-Control (continued)
3.2.5 Emergency Alert
When the administrator for Crestron RoomView® Express sends out an alert
message, it will be displayed on the screen.
You can reply to the alert message via a chat format. Input a message in the box
below the alert message, and click the [Send] button.
NOTE • For details about the Emergency Alert, refer to the manual of Crestron
RoomView® Express.
• The alert message from Crestron RoomView® is displayed on the screen of
the projector in a way similar to the real-time text of the Messenger function
(&51). If another real-time text is currently being displayed, it will be overwritten
by the alert message. However, if the priority of the real-time text is set to high,
it will not be overwritten by the alert message, and the latter will not appear
on the screen of the projector. For details, refer to the Messenger application
manual.
49
4. My Image Function
4. My Image Function
The projector can display still images that are transferred via the network.
Transfer image
1
2
3
4
Display image (ex.
)
MY IMAGE transmission requires a proprietary software application for your
computer.
Use the application to transfer the image.
It can be downloaded from the InFocus website (www.infocus.com/support).
For more information, refer to the application manual.
To display a transferred image, select the MY IMAGE item in the NETWORK menu.
For more information, see the MY IMAGE description in the NETWORK menu.
(NETWORK menu in the Operating Guide)
NOTE • It is possible to send up to 4 image files.
• MY BUTTON will display an image, if it is associated with MY IMAGE.
(OPTION menu in the Operating Guide)
• The image file also can be displayed by using the schedule function from the
web browser. Refer to item 7.3 Event Scheduling (&59) for details.
• If you display MY Image on screen while you are using the USB
Display function, the USB Display application will close. To restart the
application, exit the MY IMAGE function, and then the projector software,
LiveViewerLiteForUSB.exe, will run again. (USB Display in the Operating
Guide)
• If data is transferred via wireless and wired LAN simultaneously, the projector
may not be able to process the data correctly.
50
5. Messenger Function
5. Messenger Function
The projector can display text messages transferred via the network on the screen
and play back audio inside the projector.
Text messages can be typed in the computer and displayed immediately or a
message which has been stored in the projector can be displayed.
Transfer text message
1
2
3
4
12
Display text message (ex.
)
The Messenger function requires a proprietary software application for your
computer. To edit, transfer and display the text message, use the application. You
can download it from the InFocus website (www.infocus.com/support). For more
information, refer to the application manual.
NOTE • It is possible to store up to 12 text messages.
• The MY BUTTON will turn text messages on and off, if it is associated with
MESSENGER. (OPTION menu in the Operating Guide)
• The text file also can be displayed by using the schedule function via the web
browser. Refer to item 7.3 Event Scheduling (&59) for the detail.
• If data is transferred via wireless and wired LAN simultaneously, the projector
may not be able to process the data correctly.
51
6. Network Bridge Function
6. Network Bridge Function
This projector is equipped with the NETWORK BRIDGE function to perform
mutual conversion of a network protocol and a serial interface.
By using the NETWORK BRIDGE function, a computer that is connected to the
projector via wireless or wired LAN is able to control an external device via RS232 communication using the projector as a network terminal.
Protocol change
TCP/IP data
RS-232
RS-232 cable
Wired LAN
LAN cable
Computer
Serial data
External device
Wireless
LAN
LAN port
USB TYPE A ports
(USB wireless adapter)
CONTROL port
6.1 Connecting devices
1) Connect the projector’s LAN port to the computer’s LAN port with a LAN
cable, or insert the USB wireless adapter into one of the USB TYPE A ports.
2) Connect the projector’s CONTROL port and the device’s RS-232 port with an
RS-232 cable, for RS-232 communication.
NOTE • Before connecting the devices, read the device manuals to ensure
the connection. For RS-232 connection, check the specifications of each port
and use the appropriate cable. (Connection to the ports in the Operating
Guide - Technical)
52
6. Network Bridge Function
6.2 Communication set up
To set up communication using NETWORK BRIDGE for the projector, use the
COMMUNICATION menu. Open the projector menu and select the OPTION
- SERVICE - COMMUNICATION menu. (OPTION menu > SERVICE >
COMMUNICATION in the Operating Guide)
1) In the COMMUNICATION TYPE menu, select NETWORK BRIDGE
(WIRELESS or WIRED depending on the type of connection you use) for the
CONTROL port.
2) Using the SERIAL SETTINGS menu, select the proper baud rate and parity
for the CONTROL port, according to the specification of the RS-232 port of
the connected device.
Item
BAUD RATE
PARITY
Condition
4800bps/9600bps/19200bps/38400bps
NONE/ODD/EVEN
Data length
8 bit (fixed)
Start bit
1 bit (fixed)
Stop bit
1 bit (fixed)
3) Using the TRANSMISSION METHOD menu, set up the CONTROL port
appropriate for your situation.
NOTE • OFF is the default setting of COMMUNICATION TYPE.
• Using the COMMUNICATION menu, set up the communication. Remember
that an inappropriate set up can cause a communication malfunction.
• When one or both of the NETWORK BRIDGE settings is selected in the
COMMUNICATION TYPE menu, the CONTROL port cannot receive
RS-232 commands.
6.3 Communication port
For the NETWORK BRIDGE function, send the data from the computer to the
projector using the Network Bridge Port which is configured in Port Settings of
web browser. (&23)
NOTE • Any number between 1024 and 65535 can be set up as the Network
Bridge Port number, except for 41794, 9715, 9716, 9719, 9720, 5900, 5500,
and 4352. 9717 is the default setting.
53
6. Network Bridge Function
6.4 Transmission method
The transmission method can only be selected when the NETWORK BRIDGE is
selected for the COMMUNICATION TYPE.
(OPTION menu > SERVICE > COMMUNICATION in the Operating Guide)
HALF-DUPLEX  FULL-DUPLEX
6.4.1 HALF-DUPLEX
This method allows the projector to make two way communication, either
transmitting or receiving data, in a single direction at a time.
The method does not allow the projector to receive data from the computer while
waiting for response data from an external device. After the projector receives the
response data from the external device (or the response limit time is past), the
projector can receive the data from the computer.
The projector controls transmitting and receiving the data to synchronize the
communication.
To use the HALF-DUPLEX method, set up the RESPONSE LIMIT TIME following
the instructions below.
TCP/IP data
Wired LAN
Computer
LAN cable
Protocol change
Serial data
RS-232
RS-232 cable
External device
Wireless LAN
Transmitting data
Transmitting data
Discarding data
Response limit
time
Response data
Response data
Transmitting data
Using the RESPONSE LIMIT TIME menu, set the response data waiting time
limit. (OPTION menu > SERVICE > COMMUNICATION in the Operating
Guide)
OFF  1s  2s  3s ( OFF)
54
6. Network Bridge Function
6.4 Transmission method (continued)
NOTE • When using the HALF-DUPLEX method, the projector can send out a
maximum of 254 bytes at once.
• If the response data from the external device does not need to be monitored
and the RESPONSE LIMIT TIME is set to OFF, the projector can receive the
data from the computer and send it out to an external device continuously.
The default setting is OFF.
6.4.2 FULL-DUPLEX
This method lets the projector make two way communication, transmitting and
receiving data simultaneously, without monitoring response data from an external
device.
When using this method, the computer and an external device will send the data
out of synchronization. If the data should be synchronized, set up the computer to
do so.
NOTE • When the computer controls the synchronization of the transmitting
and receiving of data, it may not be able to control an external device well
depending on the computer's processing status.
55
7. Other Functions
7. Other Functions
7.1 E-mail Alerts
The projector can automatically send an alert message to specified e-mail
addresses when the projector detects a maintenance or error condition.
NOTE • Up to five e-mail addresses can be specified.
• The projector may be not able to send an e-mail if the projector suddenly
loses power.
Mail Settings (&24)
To use the projector’s e-mail alert function, configure the following items through a
web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter “http://192.168.1.10/” into the address bar of the web browser, and select
Projector Web Control from the selection window.
2) Enter your user name and password, and then click the [OK].
3) Click [Mail Settings] and configure each item. Refer to item 3.1.5 Mail
Settings (&24) for further information.
4) Click the [Apply] button to save the settings.
NOTE • Click the [Send Test Mail] button in [Mail Settings] to confirm
that the e-mail settings are correct. The following mail will be delivered to the
specified addresses.
Subject line
Text
56
:Test Mail
:Send Test Mail
Date
Time
IP Address
MAC Address
<Projector name>
<Testing date>
<Testing time>
<Projector IP address>
<Projector MAC address>
7. Other Functions
7.1 E-mail Alerts (continued)
5) Click [Alert Settings] on the main menu to configure the E-mail Alerts settings.
6) Select and configure each alert item. Refer to item 3.1.6 Alert Settings (&31)
for further information.
7) Click the [Apply] button to save the settings.
Failure/Warning e-mails are formatted as follows:
Subject line
Text
: <Mail title>
: <Mail text>
Date
Time
IP Address
MAC Address
<Projector name>
<Failure/Warning date>
<Failure/Warning time>
<Projector IP address>
<Projector MAC address>
57
7. Other Functions
7.2 Projector Management using SNMP
SNMP (Simple Network Management Protocol) enables you to manage projector
failure and warning status information from a computer on the network. The SNMP
management software is required on the computer to use this function.
NOTE • SNMP functions should be managed by a network administrator.
• SNMP management software must be installed on the computer to monitor
the projector via SNMP.
SNMP Settings (&23)
Configure the following items from a web browser to use SNMP.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter “http://192.168.1.10/” into the address bar of the web browser, and select
Projector Web Control from the selection window.
2) Enter your user name and password, and then click the [OK].
3) Click the [Port Settings] on the main menu.
4) Click the [Download MIB file] to download a MIB file.
NOTE • To use the downloaded MIB file, specify the file by your SNMP
manager.
5) Click the [Enable] check box to open the SNMP Port. Set the IP address to
send the SNMP trap when a Failure/Warning occurs.
NOTE • A Network Restart is required after the SNMP Port configuration
settings have been changed. Click [Network Restart] on the main menu and
click the [Restart] button. Then configure the following items.
6) Click the [Security Settings] on the main menu.
7) Click the [SNMP] and set the community name on the screen that is displayed.
NOTE • A Network Restart is required after the Community name has been
changed. Click [Network Restart] on the main menu and click the [Restart]
button. Then configure the following items.
8) Configure the settings for Trap transmission of Failures/Warnings. Click the
[Alert Settings] on the main menu and select the Failure/Warning item to be
configured.
9) Click the [Enable] check box to send out the SNMP trap for Failures/Warnings.
Clear the [Enable] check box when SNMP trap transmission is not required.
10) Click the [Apply] button to save the settings.
58
7. Other Functions
7.3 Event Scheduling
The scheduling function enables to set up scheduled events including power on /
power off. It helps the projector become "self-managed".
NOTE • You can schedule the following types of events: Power, Input Source,
My Image, Messenger, Slideshow. (&28)
• The power on event has the lowest priority among the all events that are
defined simultaneously.
• There are 3 types of Scheduling, 1) daily 2) weekly 3) specific date. (&27)
• The priority for scheduled events is as follows 1) specific date 2) weekly 3)
daily.
• Up to five specific dates are available for scheduled events. Priority is given to
those with the lower numbers when more than one event has been scheduled
for the same date and time (e.g., ‘Specific date No. 1’ has priority over ‘Specific
date No. 2’ and so on.
• Be sure to set the date and time before enabling scheduled events. (&30)
Once you turn off the projector in the SAVING mode (&SETUP menu in the
Operating Guide) or the AC power, the current date and time setting is reset.
set.
59
7. Other Functions
7.3 Event Scheduling(continued)
Schedule Settings (&27)
Schedule settings can be configured from a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter “http://192.168.1.10/” into the address bar of the web browser, and select
Projector Web Control from the selection window.
2) Enter your user name and password, and then click the [OK].
3) Click [Schedule Settings] on the main menu and select the required schedule
item. For example, if you want the command to be completed every Sunday,
select the [Sunday].
4) Click the [Enable] check box to enable scheduling.
5) Enter the date (month/day) to schedule a specific date.
6) Click the [Apply] button to save the settings.
7) After configuring the time, command and parameters, click [Register] to add
the new event.
8) Click the [Delete] button when you want to delete a schedule.
There are three types of scheduling.
1) Daily: Performs the specified operation at a specified time every day.
2) Sunday ~ Saturday: Performs the specified operation at the specified time on a
specified day of the week.
3) Specific date: Performs the specified operation on the specified date and time.
NOTE • In standby mode, the POWER indicator will flash green for approx. 3
seconds when at least 1 “Power ON” schedule is saved.
• When the schedule function is used, the power cord must be connected to
the projector and the outlet. The schedule function does not work when the
breaker in a room is tripped. The power indicator lights orange or green when
the projector is receiving AC power.
60
7. Other Functions
7.3 Event Scheduling(continued)
Date/Time Settings (&30)
The Date/Time setting can be adjusted from a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter “http://192.168.1.10/” into the address bar of the web browser, and select
Projector Web Control from the selection window.
2) Enter your user name and password, and then click the [OK].
3) Click the [Date/Time Settings] on the main menu and configure each item.
Refer to item 3.1.8 Date/Time Settings (&30) for further information.
4) Click the [Apply] button to save the settings.
NOTE • The internal clock’s time may not remain accurate. Using SNTP is
recommended to maintain accurate time (&31).
• Once the AC power is turned off or the projector goes into SAVING mode
(&SETUP menu in the Operating Guide), the current date and time setting is
reset.
61
7. Other Functions
7.4 C
ommand Control via the Network
You can configure and control the projector via the network using RS-232
commands.
Communication Port
Port no. 23 (TCP #23) is assigned for command and control.
Command Format
You can use RS-232 commands without any changes. (RS-232
Communication in the Operating Guide - Technical)
Automatic Connection Break
The TCP connection will be automatically disconnected after 30 seconds of
inactivity.
62
7. Other Functions
7.5 Crestron RoomView®
Crestron RoomView® is a multi-user resource management program provided
by Crestron Electronics, Inc. It is an application for managing and controlling the
projector and other AV devices collectively.
For details about the Crestron RoomView®, refer to the Crestron® website.
URL: http://www.crestron.com (as of May 2012)
The following communication interfaces can be used to manage the entire facility.
1) Crestron RoomView® Express / Crestron RoomView® Server Edition
RoomViewTM Express and RoomViewTM Server Edition are software provided
by Crestron Electronics, Inc. They are used for managing all the AV devices,
and are also able to communicate with the help desk as well as send out alert
messages.
For details about the software, refer to the following website.
URL: http://www.crestron.com/getroomview (as of May 2012)
2) Crestron e-Control®
Crestron e-Control® is a system controller that can be operated from a web
browser (&42).
63
8. Troubleshooting
8. Troubleshooting
Problem
Can't communicate
Likely Cause
Things to Check
Weak radio signal
• Bring the computer and
projector closer together.
• Radio waves won’t go
through concrete and metal
(steel doors, etc.)
–
Cannot communicate due
to wireless / encryption
configuration settings.
If there is a wireless
configuration utility loaded
on your computer, check its
settings.
Refer the manual of your
configuration utility.
–
The computer and/or
projector's network settings
are not configured correctly.
Check the network
configurations of the
computer and projector.
–
The same network address is Change the network address
being used for both wireless settings for wireless or wired
and wired LAN.
LAN.
Others
- Information from
the projector to
computer is not
correct or complete
- The projector does
not respond
64
Reference
Page
Number
20, 21
<Only for wireless LAN>
The USB wireless adapter
is not inserted into the
projector.
Insert the optional USB
wireless adapter.
–
<Only for wireless LAN>
There is another projector or
device close by that has the
same wireless setting.
Try changing of SSID and IP
Address.
20
Communication between the
projector and computer is not
Try “NETWORK RESTART”
working well.
in SERVICE menu under the
NETWORK menu.
Projector's network functions
are not working well.
In the
Operating
Guide
9. Specifications
9. Specifications
Item
Specifications
Control software
Dedicated computer application and Web browser
Corresponding
protocol
TCP/IP, DHCP client and HTTP server
Network
Wireless LAN (IEEE802.11b/g/n)
(Ad-Hoc and Infrastructure modes)
Wired LAN(100Base-TX/10Base-T)
Security
WEP (64/128bit), WPA-PSK (TKIP/AES),
WPA2-PSK (TKIP/AES), SSID
Computer
application's system
requirements
OS: W
indows® XP Home
Windows® XP Professional
Windows Vista® Home Basic
Windows Vista® Home Premium
Windows Vista® Business
Windows Vista® Ultimate
Windows Vista® Enterprise
Windows® 7 Starter
Windows® 7 Home Basic
Windows® 7 Home Premium
Windows® 7 Professional
Windows® 7 Ultimate
Windows® 7 Enterprise
CPU: Pentium 4 (2.8 GHz or higher)
Graphic card: 16 bit, XGA or higher
Memory: 512 MB or higher
Hard disk space: 100 MB or higher
Web browser: Internet Explorer® 6.0 or higher
CD-ROM/DVD-ROM drive
USB wireless adapter
Gemtek USB-Link11n
65
10. Warranty and after-sales service
10. Warranty and after-sales service
If a problem occurs with the equipment, read the 8. Troubleshooting (&64)
section first and review all suggestions. If you still have a problem after that,
contact your dealer or service company. They will tell you what your projector's
warranty status is.
66
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement