smokejet. - magic fx

smokejet. - magic fx
USER AND INSTALLATION MANUAL
ENGLISH
SMOKEJET.
®
SMOKE FX
PART01085
rev 01-00
User Manual
SAFETY INFORMATION
Please read the following safety information carefully before operating
the machine. Information includes important safety information about
installation, usage, and maintenance. Pay attention to all warning labels
and instructions in this manual and printed on the machine.
If you have questions about how to operate the machine safely, please contact
your local MAGIC FX dealer for help.
․
․
․
․
․
․
․
․
․
․
․
․
․
․
Keep this device dry.
Always connect to a grounded circuit to avoid risk of electrocution.
Before connecting machine to power, always check voltage indicate on
machine match to your local AC voltage. Do not use the machine if AC
power voltage does not match.
Disconnect the machine from AC power before servicing and when not
in use.
This product is for indoor use only! Do not expose to rain or moisture. If
fluid is spilled, disconnect AC power and clean with a damp cloth. If fluid
is spilled onto electronic parts, immediately unplug the machine and
contact your local MAGIC FX dealer for advice.
No user serviceable and modifiable parts inside. Never try to repair this
product, unauthorized technician may lead machine to damage or
malfunction.
For adult use only. Never leave the machine running unattended.
Installed in well ventilated area. Provide at least 50 cm space around the
machine.
Never add flammable liquid of any kind to the machine.
Make sure there are no flammable materials close to the machine while
operating.
Only use MAGIC FX fluid. Other fluid may lead to heater clog and
malfunction.
If the machine fails to work, unplug the machine and stop operation
immediately. Contact your local MAGIC FX dealer for advise.
Before transporting the machine, make sure the fluid tank is completely
drained.
Smoke fluid may present health risks if swallowed. Do not drink smoke
fluid. Store it securely. In case of eye contact or if fluid is swallowed
immediately look for medical advice.
UNPACKING AND INSPECTION
Immediately upon receiving the machine, carefully unpack the carton, check all
content to ensure that all parts are present and have been received in good
condition. If any parts appear damaged or mishandled from shipping, notify the
shipper immediately and retrain the packing material for inspection.
What is included:
1 x SMOKEJET
1 x Remote
1 x PowerCON True1 to Shuko (1,5 m)
1 x User Manual
PRODUCT DIMENSION
385.7 MM
345 MM
193 MM
PRODUCT OVERVIEW
22 x 3W LED
(5R, 6G, 6B, 5A)
LCD Control Panel
Wireless Receiver
PowerCon
XLR 5-Pin DMX Connector
SETTING UP
Step 1: Place the machine on a flat surface and in a suitable large area with at
least 50 cm open space around the machine.
Step 2: Fill the fluid tank with MAGIC FX approved fluid.
Step 3: Connect the machine to suitable rated power supply. To determine the
power requirement for the machine refer to the label on the back of the machine.
Always connect the machine to a protected circuit and ensure it is
properly grounded to avoid risk of electrocution.
Step 4: Turn on the machine and allow it to heat up. Heat up takes approximatly 5
mintues. Once the machine has reached operating temperature, the LCD display
will show “Ready To Fog”. Now the machine is ready for operation.
Step 5: To start making fog, locate the OUTPUT button on the control panel, and
press the button to start making fog.
Step 6: To turn off the machine, press STOP button and turn Powercon to the OFF
position.
OPERATION
Control Panel Operation
The machine can be operated with onboard digital control interface
Button
Function
[MENU]
Scroll through setting menu
▲ [UP]/[TIMER]
Up/Activate Timer function
▼ [DOWN]/[OUTPUT]
Down/Activate Output function
[STOP]
Deactivate Timer/Volume function
CONTROL MENU
DMX512 Set DMX address from 1 to 504
Address: 1 Stand Alone Set machine as Master of Slave unit
Set Master Color Mode Turn LED On or Off
On Color Mode Set LED output color from macro 1 to 10
Marco:01 Color Mode Set LED chase from 1 to 15
Chase:01 Timer Set interval from 15 to 360 seconds
Interval 15 Sec Timer Set duration from 1 to 5 seconds
Duration 5 Sec Wireless Setting Turn On or Off wireless control
On Wireless Setting Button A:M01 Wireless Setting Button B:M01 Wireless Setting Button C:M01 Set wireless remote button function macro color 1 to 10 or
chase 1 to 15 and off.
Set wireless remote button function macro color 1 to 10
or chase 1 to 15 and off.
Set wireless remote button function macro color 1 to 10
or chase 1 to 15 and off.
Set wireless remote button function macro color 1 to 10
or chase 1 to 15 and off.
Wireless Setting Button D:M01 LED Setting Fog Only Setting for LED to turn on with fog only or always on.
LED Fade Out Delay: 0 Sec Set LED delay time from 0 to 5 seconds.
Run Last Setting On 2 Second Jet Mode Turn On/Off run last setting function
Turn On/Off 2 Second Jet Mode
Off W‐DMX512 Off Wired DMX control:
Wireless DMX control:
W-DMX512 OFF
W-DMX512 ON
W‐DMX Rest Off Reset W-DMX connection
WIRELESS OPERATION
Wireless remote control system consists of a transmitter equipped with four buttons to
activate four user configurable LED setting and fog; with an onboard receiver attach
to the rear panel of SmokeJet.
Remote
Wireless Receiver
Wireless settings are configurable through onboard control panel, refer to control
menu section to setup each buttons.
In a free open space the effective distance is 50 meters, actual usage depending
on obstacle level the effective distance is 10-25 meters.
REGISTERING TRANSMITTER
Transmitter can be pair or deleted from the receiver. Each receiver can pair up to
10 transmitters. Follow below steps to pair or delete transmitter from receiver.
Step 1: Power off SMOKEJET
Step 2: Press and hold [DOWN] button
Step 3: Turn power on and release [DOWN] button when LCD display blinks
Step 4: Follow the menu instruction to pair or delete transmitter
TRANSMITTER BATTERY REPLACEMENT
If effective distance seems to be decreased, it is possible the battery level are low
and require replacement. In order to replace the battery, undo the three screws on
the back of transmitter to release the cover. Replace with same type and
specification of battery which is 27A 12V
DMX CONNECTOR PIN ASSIGNMENT
The machine provides 5 pin XLR connector for DMX connection. Diagram below
indicate pin assignment information
Pin
1
2
3
Function
Ground
DataData+
DMX CHANNEL FUNCTION
Channel 1
DMX Value Range
Function
Fog
0–4
5 – 255
Fog Off
Fog On
Channel 2
DMX Value Range
Function
Red LED
0-255
0-100%
Channel 3
DMX Value Range
Function
Green LED
0-255
0-100%
Channel 4
DMX Value Range
Function
Blue LED
0-255
0-100%
Channel 5
DMX Value Range
Function
Amber LED
0-255
0-100%
Channel 6
DMX Value Range
Function
1-15
Chase 1
16-31
Chase 2
32-47
Chase 3
48-63
Chase 4
64-79
Chase 5
80-95
Chase 6
96-111
Chase 7
112-127
Chase 8
128-143
Chase 9
144-159
Chase 10
160-175
Chase 11
176-191
Chase 12
192-207
Chase 13
208-223
Chase 14
224-255
Chase 15
Channel 7
DMX Value Range
Function
Chase Speed
0-255
0-255 step per min
Channel 8
DMX Value Range
Function
Master Dimmer
0-255
0-100%
Channel 9
DMX Value Range
Function
Strobe
0-255
1-20 Hz
Chase
FLUID
Use MAGIC FX Smoke Fluid for the best effect for the SMOKEJET. The machine is
tested and calibrated with this liquid to get the best output performance. Warranty
will be void if any other type of liquid is used, improper use of liquid may lead to
machine failure and malfunction.
SERVICE AND MAINTENANCE
Do not allow the machine to become contaminated.
Remove dust from air vents with air compressor, vacuum or a soft brush.
Only use a damp cloth to clean the casing.
Before storing run distilled water through the system to help avoid condensing
the pump or heater.
It is recommended to run the machine on a monthly basis in order to achieve
best performance and output condition.
Excessive dust, liquid and dirt built up will degrade performance and cause
overheating.
․
․
․
․
․
․
BREAKER RESET
Disconnect AC power before reset breaker. Only replace fuse with same
type and rating.
Step 1: Disconnect AC power
Step 2: Flip breaker to ON position
Step 3: Turn on machine to test
BREAKER
230V = 9A 250V
FAQ

Why does the machine not respond on any wired DMX input?
Make sure the W-DMX512 is turned OFF.
TECHNICAL SPECIFICATIONS
Input voltage
230Vac 50/60Hz
Breaker
230Vac = 9A 250Vac
Heater
1420W
Warm-up time
5 min. (approx.)
Coverage volume
Height 5 Meter, Width 1 Meter
Max. operating time
8 seconds burst
Fluid tank capacity
2.4 L
Fluid consumption
2,5 ml/s.
Recommended Fluid
MAGIC FX Fog Fluid for the best effect
Control option
DMX 512, Manual, Timer, Wireless remote
DMX addresses
9 addresses
Power connection
Neutrik® powerCON TRUE1 DMX data connection
5-pin XLR
Dimension
L345 x W193 x H380 mm
Dry weight
11.1 kg
WWW.MAGICFX.EU
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement