User`s Guide - Normandeau Technologies
BASIC FEATURES
MAKE AN OUTSIDE CALL
1)
2)
User’s Guide
Lift handset and dial 9 for next available line then dial number
Or press a LINE button for outside dial tone then dial number
ANSWER A CALL RINGING AT YOUR STATION
1)
Lift handset or press SPEAKER button for hands free
ANSWER A CALL RINGING AT ANOTHER STATION
This user’s guide is to be used for
LDP-7008D
Digital Phone
1)
2)
Lift handset or press SPEAKER button for hands free
Dial 7 followed by the station number to pick up
ANSWER A CALL RINGING AT GROUP MEMBER STATION
1)
2)
3)
Lift handset or press SPEAKER button for hands free
Dial 566 for ringing member station
OR press PICK-UP soft key for ringing member station
TRANSFER CALL TO EXTENSION
1)
2)
3)
4)
While on Call press TRANS/PGM button or TRANS soft key
Dial the Station number or press pre-programmed flexible button
Announce Call (supervised transfer only)
Hang up
TRANSFER CALL TO VOICEMAIL
Configured on eMG80 Phone System
For more info, contact us at:
Normandeau Technologies
[email protected]
1)
2)
3)
4)
While on Call press TRANS/PGM button or TRANS soft key
Press CALL BACK button
Dial the Station number or press pre-programmed flexible button
Hang up
MAKE AN INTERCOM CALL
1)
2)
Lift handset or press SPEAKER button
Dial the Station number or press pre-programmed flexible button
PLACE A CALL ON HOLD
Press the HOLD/SAVE button to retain call at your station
(413) 584.3131
RETRIEVE CALL ON HOLD
Press flashing LINE key on the phone to retrieve your held call
PAGE (ALL CALL)
MUTE
1)
2)
3)
Press MUTE soft key to switch ON/OFF the microphone
Lift handset
Dial 5 4 9 then wait for tone before speaking
Hang up
REDIAL
1)
2)
DO NOT DISTURB (DND) –Not available Attendant station
Press DND button OR dial 5 5 3 to switch ON/OFF
Press the REDIAL button or soft key, scroll through last 10 dialed numbers using the navigation
buttons (16 & 24 button handsets) or volume button (4 & 8 button handsets)
Press HOLD/SAVE button
SET INTERCOM ANSWER MODE
This determines how your Station will ring when receiving an intercom call
ADVANCED FEATURES
1)
2)
MAKING A CONFERENCE CALL
1)
2)
3)
4)
5)
Dial first party
Press CONF button or soft key
Dial 9 followed by phone # or dial another extension
Continue above steps until all parties are connected
Press CONF button twice to commence conference
#Note that you must have a CONF button programmed and conference access. The number of
external members is limited to the number of lines on the system. All lines are in use for the
duration of the Conference call.
CHANGE HEADSET/SPEAKER MODE
1)
2)
3)
4)
Press TRANS/PGM button
Dial 6 1 (Change Speaker key to headset key)
Select 1(For Speaker) 0 (For Headset)
Press HOLD/SAVE or OK button
Speakerphone is disabled while phone is in headset mode; the speaker key becomes an ON/OFF toggle
button for the headset.
CALL FORWARD TO STATION OR OUTSIDE LINE
1)
2)
3)
Dial 5 5 4
Select 1 for Unconditional All Calls
After selection dial Station number (e.g. 1000), or dial 9 followed by outside phone
number
Calls will terminate at the destination station/number VM
CANCEL CALL FORWARD
Dial 5 5 4 followed by the # button to cancel
3)
Press TRANS/PGM button
Dial 1 3 and select
1. Hands free (Auto answer after a BEEP tone)
2. Tone ring
3. Privacy announce (Auto Answer but you must pick-up the handset to talk)
Press HOLD/SAVE button or the OK button
PROGRAM SPEED DIAL NUMBER
1)
2)
3)
4)
5)
6)
7)
8)
9)
Press TRANS/PGM button
Press SPEED button - Display will show next available speed bin number(Personal Speed
bin range 000-099)
Press HOLD/SAVE button to select next available or dial desired speed bin number to
edit specific number
Dial 9 for outside line
Enter the phone number you wish to store
Press HOLD/SAVE button
Enter name label using number chart
Press HOLD/SAVE button
Press SPEAKER button to exit
BUTTON CODES FOR FLEXIBLE BUTTON PROGRAMMING





CONF
CALLBK
DND
REDIAL
MUTE
TRANS/PGM 9 1
TRANS/PGM 9 2
TRANS/PGM 9 3
TRANS/PGM 9 7
TRANS/PGM 9 5
Example: CONF button. Press TRANS/PGM then flex key to program. Press TRANS/PGM again
followed by 9 1 then dial HOLD/SAVE to save.
TO ERASE FLEXIBLE BUTTON
SPEED DIAL ACCESS/USE
1)
2)
Lift handset and/or press SPEED button
Dial speed bin number
a. Personal: (000-099)
b. System:(2000 through 4999)
1)
2)
3)
Press TRANS/PGM button
Press flexible button to program
Press HOLD/SAVE button
VOICEMAIL
ACCESS VOICEMAIL ON-SITE
SPEED DIAL BY DIRECTORY SEARCH
• Press VM Access button OR dial preconfigured Group number for Voice Mail (Typically 401)
1)
2)



3)
• Enter password (Default is extension number followed by a 9). System password is looking
for extension followed by password. For example: extension 100 with a password of 1234 will
be entered as 1001234when prompted for password
4)
Press SPEED button twice
Select corresponding number for the Phone Book
Dial 1 View Station name for internal extensions
Dial 2 Private Directory for personal speed dials
Dial 3 Public Directory for system speed dials
Dial Letter using the number chart and/or scroll up and down using either volume key or
navigation dial.
Select Station or Speed bin by pressing the HOLD/SAVE button
PROGRAM FLEXIBLE BUTTON
1)
2)
3)
4)
5)
Press TRANS/PGM button
Press flexible button to program
Dial feature e.g. Station No. (200), group number (VM 401) or desired button codes (see
list)
Press HOLD/SAVE button
Press SPEAKER button to exit
ALARM SILENCE CODE – Dial 565 from attendant phone
• Follow the voice prompts to navigate through voice mail, mail box configuration, voice mail
greeting, or password
REMOTE ACCESS TO VOICE MAIL
• Once your Voice Mail has answered your call and during your greeting dial the # key
• Enter password (Default is extension number then *, i.e. 100*)
• Follow the voice prompts to navigate through voice mail, mail box Configuration, voice mail
greeting, or password
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement