Installation Guide
Installation Guide
Viking Range, LLC
111 Front Street
Greenwood, Mississippi 38930 USA (662) 455-1200
For product information,
call 1-888-(845-4641)
or visit our web site at vikingrange.com in the US
or brigade.ca in Canada
UL
F21312 EN
17-3479-02
C
UL
(091513)
15”W. Undercounter/Freestanding
Nugget Ice Machine
Table of Contents
Important - Please read and Follow!
Warnings & Important Safety Instructions ______________________________________________________________________3
Dimensions (Professional) ____________________________________________________________________________________5
Dimensions (Custom Panel) __________________________________________________________________________________6
Specifications ______________________________________________________________________________________________7
Cutout Dimensions _________________________________________________________________________________________7
Drain/Electrical Locations ____________________________________________________________________________________8
General Information ________________________________________________________________________________________9
Air Flow ___________________________________________________________________________________________________9
Filters and Treatment _______________________________________________________________________________________9
Installation Overview_______________________________________________________________________________________10
Accessory Door Panel ______________________________________________________________________________________10
Custom Panel _____________________________________________________________________________________________10
Door Panel Attachment ____________________________________________________________________________________12
Door Swing Change _______________________________________________________________________________________13
Water and Drain Installation ________________________________________________________________________________14
Electrical Connection ______________________________________________________________________________________16
Final Installation ___________________________________________________________________________________________16
Installation Checklist _______________________________________________________________________________________16
Service Information ________________________________________________________________________________________17
•
•
•
•
•
Before beginning, please read these instructions completely and carefully.
DO NOT remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
Please observe all local and national codes and ordinances.
Please ensure that this product is properly grounded.
The installer should leave these instructions with the consumer who should retain for local inspector’s use and for
future reference.
A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local laws, or local ordinances.
• The required use of a GFI is normally related to the location of a receptacle with respect to any significant sources of
water or moisture.
• Viking Range, LLC will NOT warranty any problems resulting from GFI outlets which are not installed properly or do not
meet the requirements below.
If
•
•
•
•
•
•
•
the use of a GFI is required, it should be:
Of the receptacle type (breaker type or portable type NOT recommended)
Used with permanent wiring only (temporary or portable wiring NOT recommended)
On a dedicated circuit (no other receptacles, switches or loads in the circuit)
Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT recommended)
Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard)
In good condition and free from any loose-fitting gaskets (if applicable in outdoor situations)
Protected from moisture (water, steam, high humidity) as much as reasonably possible
WARNING
To reduce the risk of fire, electric shock, or injury when using your unit, follow these basic precautions:
• Read all instructions before using the unit.
• Never allow children to operate, play with, or crawl inside the unit.
• Never clean unit parts with flammable fluids. The fumes can create a fire hazard or explosion.
• Always turn the power on/off switch (located behind the air grille on top right side) to the OFF
position before attempting to change light bulbs, clean, or service the unit.
FOR YOUR SAFETY
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE
VICINITY OF THIS OR ANY OTHER APPLIANCE. THE FUMES CAN CREATE A FIRE HAZARD OR
EXPLOSION.
It
•
•
•
•
is your responsibility to be sure your ice machine is:
located so the front is not blocked to restrict incoming or discharge air flow.
properly leveled.
located in a well ventilated area.
connected to the proper kind of outlet, with the correct electric supply and grounding. A 115V, 60 Hz, 15 amp fused
electrical supply is required. Note: Time delay fuse or circuit breaker is recommended.
• not used by anyone unable to operate it properly.
• used only for its intended purpose.
• properly maintained.
•SAVE THESE INSTRUCTIONS•
2
3
Important - Please read and Follow!
Dimensions
PROPER DISPOSAL (OF OLD REFRIGERATION UNIT)
DANGER
FGNI/FPNI w/ Professional door panel
14
(37-7/8
.8 ”
cm
)
RISK OF CHILD ENTRAPMENT
Before You Throw Away Your Old Refrigeration Unit:
• Take off the doors.
• Leave the shelves in place so that children may not easily climb
inside.
30
-5/
(77
.0
33
(86-7/8
.0 ”
mi cm)
n.
34 to
(88-7/8
.6 ”
ma cm)
x.
16
c ”
m)
IMPORTANT: Child entrapment and suffocation are not problems of the
past. Junked or abandoned refrigeration units are still dangerous... even if
they will sit for “just a few days.”
IMPORTANT:
Now that you have a new ice machine, it is extremely important that you
dispose of your old appliance in a way that minimizes the possibility that
children will find it. There have been many cases in years past of children
crawling inside junked and abandoned refrigeration units and becoming
trapped or suffocated.
4”
-1/cm)
9
1
.9
(48
/4”)
3
2 cm
2 .8
7
(5
Contact your municipal waste disposal authority to find out the best and
safest way to dispose of your old refrigeration unit.
/4”)
1
5 cm
2 .1
64
(
14-3/4”
(37.5 cm)
Door Swing
3-7/8”
(9.8 cm)
Floor drain
access hole
20-3/8”
(51.6 cm)
22-3/4”
(57.8 cm)
2-1/2”
(6.4 cm)
115.0°
90.0°
4
5
37-3/4”
(95.9 cm)
Dimensions
Specifications
FGNI/FPNI w/ Custom door panel
15”W. Undercounter/Freestanding Ice Machine
14
(37-7/8
.8 ”
cm
)
33
30
(86-7/8
.0 ”
mi cm)
n.
t
o
34
(88-7/8
.6 ”
ma cm)
x.
(7 5/1
7.0
FGNI515
Description
6
cm”
)
/4”)
1
9 cm
Overall width
14-7/8” (37.8 cm)
Overall height
33-7/8” (86.0 cm) min. to 34-7/8” (88.6 cm) max.
Overall depth from rear
(without door panel)
(with door panel)
(with door handle)
22” (55.9 cm)
22-3/4” (57.8 cm)
25-1/4” (64.1 cm)
Cutout width
15” (38.1 cm)
Cutout height
34-1/4” (86.4 cm) min. to 35-1/4” (89.5 cm) max.
Cutout depth
24” (61.0 cm)
Electrical requirements
115V/60 Hz, 15 amp dedicated circuit
6’ 3-wire cord attached to product
Maximum amp usage
5.0 amps
1/4” OD copper tubing inlet waterline
20 psi min. to 80 psi max.
50°F (10°C) min. to 100°F (38°C) max.
Inlet water requirement
1 .9
8
(4
/4”)
3
2 cm
2 .8
57
(
FPNI515
Drain requirements
5/8” ID x 7/8” OD plastic tubing
required
3/8” ID x 10’ plastic tubing supplied
Temperature requirements
50°F (10°C) min. to 100° (38°C) max.
Maximum storage capacity
26 lbs.
Approximate
shipping weight
124 lbs. (56.2 kg)
129 lbs. (58.5 kg)
CUTOUT
DIMENSIONS
14-3/4”
(37.5 cm)
3-7/8”
Door Swing
(9.8 cm)
15” (38.1 cm)
Floor drain
access hole
20-3/8”
(51.6 cm)
34-1/4” (86.4 cm) min.
to
35-1/4” (89.5 cm) max.
22-3/4”
(57.8 cm)
” )
24 cm
0
1.
115.0°
37-3/4”
90.0°
(95.9 cm)
6
(6
7
Drain / Electrical Location
Installation
INSTALLATION OVERVIEW
1/4” (0.6 cm)
O.D. Copper Water
Inlet Compression
Fitting Provided
2-3/4”
(7.0 cm)
The ice machine must:
• Be connected to cold, potable water.
• Be connected to a drain.
• Be connected to the proper power supply.
• Be able circulate air through the vents at the front.
5-1/8”
(13.0 cm)
Note: DO NOT build in so that the door is recessed. Door is meant to be flush with surronding cabinetry, but
not recessed.
INSTALLATION PARTS
The following installation parts are supplied with the ice machine:
2-Hinge covers
2-Door stop pins
2-Hinge side covers
10-#8 sheet metal screws
2-Hole plugs
2-8-32 Machine screws
2-Hinge opening covers
4-Leveling leg caps
1-Upper door bracket (LH)
2-Black kickplate screws
1-Lower door bracket (LH)
1-Access panel button cover
ACCESSORY DOOR PANEL
The ice machine is supplied without a finished door panel. Accessory door panels are offered or a custom panel may
be used.
2-1/2”
(6.4 cm)
115V
Power Cord
Accessory Door Panel Attachment
Note: If door swing is to be changed, it must be done before panel is attached.
3-1/4”
(8.3 cm)
7-1/2”
(19.1 cm)
11-5/8”
(29.5 cm)
Drain Access - Flexible Tubing
3/8” (.95 cm) I.D. Pump Model (included)
5/8” (1.6 cm) I.D. Gravity Model (not included)
AIR FLOW
To attach a door panel:
The panel will be held on by 6 screws (supplied with door panel) and 2 machine screws (supplied with ice machine).
1. Remove the gasket and retain for later use.
2. If the door panel is stainless steel, remove any plastic covering the stainless steel panel.
3. Place the panel onto the outside of the door, and secure it
to the door using two machine screws, located at the left
center and right center (behind door gasket).
4. Fasten the panel to the door using the 6 screws (supplied
Hole
with door panel). In the hinge area, use the outermost screw
plug
holes.
5. Place the covers over the hinge areas, and secure each cover
Cover
to the door using a screw (supplied with door panel).
6. Insert hole plug over screw installed in step 5 (supplied).
Gasket
7. Return the gasket to its original position.
The machine takes in room temperature air at the lower right
front and forces warm air out the lower left front. Restricting the
airflow will adversely affect the ability of the ice machine to
make ice.
Warm
air out
Air
intake
8
9
Installation (con’t)
Installation (con’t)
CUSTOM PANEL
CUSTOM PANEL DIMENSIONS
A custom panel of wood or other material not exceeding 15 lb can be attached to the door. Attachment is from the ice
side of the door. Holes are provided in the door for this purpose.
To
•
•
•
create and attach a custom panel:
Panel width: 14-7/8” (37.9 cm)
Panel height: 30-5/16” (77.0 cm)
Panel thickness: 5/8” (14.5 cm) to 3/4” (1.9 cm)
1. Measure overall height of cabinet opening where ice machine will be (floor to botom of countertop edge).
2. Determine desired kickplate space (from bottom of door to floor). This could be equal to the adjacent cabinet’s
kickplate space or another space the user wants.
3. Subtract kickplate space from cabinet opening.
4. Subtract 1/8” or more for clearance space between top of door and bottom of countertop edge from cabinet
opening. This is the maximum door length.
5. Cut panel to width
6. Cut panel to length (cabinet space - kickplate space - top clearance = length).
7. Determine top of panel.
8. Mark hole locations using drawing on the back of these instructions. Drawing assumes top of panel will be flush
with top of door. Measure hole locations from the top of the panel.
9. Drill pilot holes for wood screws. Use drill stop to prevent drilling through the panel.
10. Mount panel to door using wood screws or supplied panel mounting screws.
13-9/16”
(34.4 cm)
6-25/32”
(17.7 cm)
13/16”
(2.4 cm)
4-1/8”
(10.5 cm)
13/32”
(1.3 cm)
14-11/16”
(37.3 cm)
ø 1/8”
TYP. (10)
Note: When installed, ice machine must be adjusted for height to position top of door to desired clearance.
30-5/16”
(77.0 cm)
13-31/64”
(34.3 cm)
13/32”
(1.3 cm)
14-7/8”
(37.9 cm)
10
8-1/4”
(20.9 cm)
11
Installation (con’t)
Installation (con’t)
DOOR PANEL ATTACHMENT
DOOR SWING CHANGE
The door can be attached to open with hinges on the left or right using new
brackets shipped loose in the ice bin. Retain all screws for re-use.
Use Upper
Hole at the
Top
Accessory
Door Panel
To change:
1. Remove inner screw holding each hinge to cabinet, loosen the outer screw.
2. Slide hinges to the side and remove door from cabinet. Remove outer screws
loosened in step 1 from both hinge brackets.
3. Remove two screws securing top panel to back, pull top panel back and
remove from cabinet.
4. Remove two screws at the top of the upper door hinge bracket and lift out of
the cabinet. Replace with the left hinge upper door bracket. Fasten it to the
cabinet using the original screws.
5. Return the top panel to the cabinet and fasten it with the original screws.
6. Remove kickplate and front service panel.
7. Remove two front screws and two bottom screws holding the lower door
hinge bracket to the cabinet. Replace with the left hinge lower door bracket.
Secure it using the original screws.
8. Remove the upper hinge and move it to the door's opposite side, bottom
location. Secure using the original screws.
9. Remove the original lower hinge and move it to the door's opposite side,
upper location. Secure using the original screws. Note: If door panel is
attached, it must be removed to access hinge screws.
10. Install a screw removed in step 2 in outer hole of upper and lower door brackets.
11. Attach the door to the cabinet using the original screws.
12. Return kickplate and front service panel to their original positions and attach to
the cabinet using the original screws.
Inner screw
Outer screw
Screw
Upper
door
bracket
Front
screw
Bottom
screw
Lower
door
bracket
Insert door
stop pin
DOOR STOP
•
•
In some situations the door can open too far and damage adjacent cabinets. To
prevent that, insert a stop into the provided hole in the top and bottom hinges
Drive the pin into the hole until the head is against the hinge.
HINGE COVERS
Gasket
After the hinge pins are installed (if used) and the door panel has been attached, attach the hinge covers.
1. Slide the hinge cover over each hinge.
2. Attach the side cover over the hinge by peeling off the covering over the
adhesive and placing it over the side of the hinge.
Note: If the hinges are used to secure the unit to the cabinet, DO NOT use the side covers.
Machine
Screw
KICKPLATE
Use Lower
Hole at the
Bottom
Hole Plug
Cover
The kickplate is black with a stainless steel covering. To use the stainless steel, no changes are required. To use the black,
remove the stainless steel covering by removing the two stainless steel screws. Replace with supplied black screws.
DO NOT remove stainless steel covering if ice machine is used outdoors.
INSTALLATION NOTES
Built In Situations: If a finished floor is to be installed in the area after the ice machine has been built in, shims the expected
thickness of the floor should be installed under the unit to keep the machine level with the planned floor level.
Installations on a slab: Use a pump model and pump the water to the point of drainage. Pump models will pump 1 story (10
feet) high.
Installations over a crawl space or basement: Either gravity drain or pump model units may be used, if there is not enough
room behind the machine for a drain/waste receptacle, the drain will have to be below the floor.
Note: When installed in a corner, the door swing may be limited due to handle contact with the wall or cabinet face.
12
13
Installation (con’t)
Installation (con’t)
WATER & DRAIN INSTALLATION
GRAVITY DRAIN PUMP MODEL DRAIN INSTALLATION
The recommended water supply tubing is 1/4” OD copper. Stainless steel flex or reinforced PVC tube may also be
used. Install an easily accessible shut-off valve between the supply and the unit. This shut-off valve should not be
installed behind the unit.
Restrictions in the drain system to the machine will cause water to back up into the ice storage bin and melt the ice. Gravity drain tubing
must be vented, have no kinks and slope to the building drain. Air gaps are typically required by local code.
The water connection is at the back of the cabinet. Connect using a
compression fitting, one is supplied tied to the water inlet tube at the back
of the cabinet.
1. Place the ice machine in front of the installation opening. Adjust leveling legs to the approximate height.
2. Insert drain tube through the routing hole in the back panel.
3. Remove the upper back panel if needed for access to drain connection.
When built-in: Coil enough tubing behind the machine so it can be pushed
into the cavity without kinking the tubing.
DRAINS
There are two types of ice machine models, one that drains by gravity and
one that has an internal drain pump.
CAUTION
Connect water supply
here, Fitting is supplied
in bag tied to tube.
Drain Pump Model drain installation
1. Locate the coil of 3/8” ID plastic drain tubing secured to the back of the unit.
2. Route the plastic drain tube from the back of the unit to the drain connection point.
The drain connection can be as high as 10 feet (3.05 m) above the ice machine. the drain pump includes a check valve
to prevent re-pumping water into the drain hose.
Note: If you are connecting a gravity drain model and the drain opening has been located in the floor under the base
pan according to the pre install specifications, follow steps 3 through 5 to drain the unit through the base. If not,
proceed to step 6b.
4. Remove the clamp and barbed elbow and take off the plastic cover in the base pan below the drain hose.
5. Connect a straight 5/8” barbed connector to the drain hose, securing with the clamp removed in step 4.
6. Cut an 8” piece of 5/8” ID X 7/8” OD tygon (clear plastic) tubing. Slide one end of the tube onto the outlet of the
barbed connector and secure with a clamp. Leave the other end of the tube lying on the floor of the base pan until
the unit is positioned over the floor drain.
7. Route the drain tube. Either a) Insert the drain tube through the base pan into the floor drain or b) Route the drain
tube through the left hole in the lower back panel and connect to barbed elbow and secure with a clamp.
8. Reinstall any panels removed.
IMPORTANT NOTE: Often an air gap is required by local codes between the ice maker drain tube and the drain
receptacle.
Water Inlet
Tube (field
supplied)
Drain Hose
Barbed Elbow
Water Inlet
Tube (field
supplied)
Drain Tube,
Route to
building drain
Drain Hose,
Route to
building drain
Back View, Drain Pump Model
Back View, Gravity Drain Model
14
15
Electrical Connection
Service Information
If service is required, call your dealer or authorized service agency. The name of the authorized service agency can be
obtained from the dealer or distributor in your area.
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow these instructions could result in fire or electrical shock.
The ice machine is supplied with a power cord. DO NOT remove the
grounding pin from the cord’s plug. DO NOT use extension cords. Follow all
codes. Connect the machine to its own 115 volt, 15 amp circuit.
Grounding type
wall receptacle
FINAL INSTALLATION
1.
2.
3.
4.
5.
6.
7.
8.
9.
If the electrical outlet for the ice maker is behind the unit, plug in the unit.
Snap the black caps over the bottom of the leveling legs.
Position the unit in the installation opening.
Turn on the water supply. Make sure that the ice maker is plugged in and
the power is on.
Power Supply
Slide unit into installation opening, paying careful attention to water supply
with 3-prong
and drain connections. DO NOT kink!
grounding plug
Remove service panel for visual inspection.
Pour a couple of quarts of water into the ice storage bin; on drain pump equipped machines the drain pump should
start and water should pump out. Check for leaks.
Replace the service access panel and insert access panel button cover (supplied)..
Level the unit as needed by turning the leveling legs clockwise to raise the unit and counterclockwise to lower the
unit.
Have the following information readily available.
• Model number
• Serial number
• Date purchased
• Name of dealer from whom purchased
Clearly describe the problem that you are having. If you are unable to obtain the name of an authorized service agency,
or if you continue to have service problems, contact Viking Range, LLC at 1-888-(845-4641), or write to:
VIKING RANGE, LLC
PREFERRED SERVICE
111 Front Street
Greenwood, Mississippi 38930 USA
Record the information indicated below. You will need it if service is ever
required. The model and serial number for your ice machine are located under
control panel in the upper compartment.
Model and
Serial number
INSTALLATION CHECKLIST
1.
2.
3.
4.
5.
6.
7.
8.
Has the unit been connected to the proper water supply?
Has the water supply been checked for leaks?
Has the unit been connected to a drain?
Has the drain been tested for flow and leaks?
Has the unit been connected to the proper electrical supply?
Has the unit been leveled?
Have all packing materials been removed from the machine?
Has the door covering been installed?
Model Number ____________________________________Serial Number ____________________________________________
Date of Purchase ____________________________________________________________________________________________
Date Installed _______________________________________________________________________________________________
Dealer’s Name ______________________________________________________________________________________________
Address ____________________________________________________________________________________________________
If service requires installation of parts, use only authorized parts to insure protection under the warranty.
KEEP THIS MANUAL FOR FUTURE REFERENCE.
16
17
18
19
ICE MACHINE ACCESSORY DOOR PANEL INSTALLATION
ACCESSORY DOOR PANEL
Hole
plug
The ice machine is supplied without a finished door panel. Accessory door panels are
offered or a custom panel may be used.
Cover
Accessory Door Panel Attachment
Note: If door swing is to be changed, it must be done before panel is attached (See
Installation Instructions).
Gasket
To attach a door panel:
The panel will be held on by 6 screws and 2 machine screws (supplied).
1. Remove the gasket and retain for later use.
2. If the door panel is stainless steel, remove any plastic covering the stainless steel
panel.
3. Place the panel onto the outside of the door, and secure it to the door using two
machine screws, located at the left center and right center (behind door gasket).
4. Fasten the panel to the door using the 6 screws (supplied in kit). In the hinge area, use the outermost screw holes.
5. Place the covers over the hinge areas, and secure each cover to the door using a screw (supplied).
6. Insert hole plug over screw installed in step 5 (supplied).
7. Return the gasket to its original position.
ACCESSORY DOOR PANEL ATTACHMENT
Use Upper
Hole at the
Top
Accessory
Door Panel
Gasket
Machine
Screw
Hole Plug
Cover
F20759A EN
Use Lower
Hole at the
Bottom
(120610)
Viking Installation Guide
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
PHK30 Professional Series Handle Kit
or visit the Viking Web site at
For Use with FRCI Refrigerators, FBCI Beverage Centers,
FWCI Wine Cellars and FGIM/FPIM Ice Machines
vikingrange.com
F20891 EN
(103111)
IMPORTANT–Please Read and Follow!
•
•
•
•
•
Before beginning, please read these instructions completely and carefully.
Use caution during assembly to minimize scratches.
Do not remove permanently affixed labels, warnings or plates from the product. This may
void the warranty.
Please refer to the product Installation Instructions for more information on installing the
door panel.
The installer should leave instructions with the customer who should retain for local
inspector’s use and future reference.
Handle Installation FRCI/FBCI/FWCI Undercounter Refrigeration
9/16”
(1.4 cm)
5/16” (0.8 cm) through-holes
with 5/8” x 1/4” counterbore
*See section A-A.
5/8”
(1.6 cm)
A
A
Installation with Wooden Full Overlay
Custom Door Front
Parts Included
Part
Professional Series Handle Tube
Professional Series End Caps
1/4” x 1” Phillips Head Screws
Installation Instructions
Quantity
(1)
(2)
(4)
29-1/16”
(73.8 cm)
Required Tools
Electric Drill
5/16” (.8 cm) Drill Bit
5/8” (1.6 cm) Spade or Forstner Bit (Counterbore)
Tape Measure
Phillips Head Screwdriver
Masking Tape and Pencil
Rubber Mallet
To Install:
TYP
1. Locate the wooden custom panel.
2. Using the illustrations on the next page, layout the handle location on the panels. It is
recommended that masking tape be placed where the four holes will be drilled to help mark
the hole placement and to prevent any damage to the door when drilling the holes.
3. The Professional handle will be mounted using (4) of the 1/4” x 1” Phillips head screws
provided. Using the 5/16”(.8 cm) drill bit, drill completely through the door in the hole
locations. Using the 5/8” (1.6 cm) bit, counter-bore two holes 1/4” (.6 cm) deep on the
BACKSIDE of the custom door panel.
4. Place a handle end cap on both ends of the handle tube. Tap the endcaps firmly into place
with a rubber mallet ensuring that both endcaps mounting surfaces are parallel.
5. Align the holes in the endcaps with the holes on the panel and attach the Professional
handle to the panel using the (4) 1/4” (.6cm) screws provided.
2
1-3/8”
(3.5 cm)
5/8” (1.6 cm) Ø x 1/4” (0.6 cm) counterbore
1-3/8” (3.5 cm)
Section A-A
Professional Series Handle
3/4” (1.8 cm)
5/16” (0.8 cm) Ø through-holes
Full Overlay Panel
3
Handle Installation -
9/16”
(1.4 cm)
FGIM/FPIM Ice Machine
5/16” (0.8 cm) through-holes
with 5/8” x 1/4” counterbore
*See section A-A.
5/8”
(1.6 cm)
A
A
29-1/16”
(73.8 cm)
1-3/8”
(3.5 cm)
Specifications subject to change without notice.
4
5
6
7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement