JBL EON 618 S Active Bass Speaker Owner's Manual

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer

’ s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including ampli

� ers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not

� t into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories speci

� ed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speci

� ed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to quali ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Service Instruction in Owner

’ s Manual:

“

CAUTION - THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE

PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT

CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.

”

16. To completely disconnect this apparatus from the AC mains, disconnect the power supply cord plug from the AC receptacle.

17.

“

WARNING

–

TO REDUCE THE RISK OF FIRE OR ELECTRIC

–

SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN

OR MOISTURE.

”

18. Do not expose this equipment to dripping or splashing and ensure that no objects

� lled with liquids, such as vases, are placed on the equipment.

19. The mains plug of the power supply cord shall remain readily operable.

EN 55103-1:1997 Electromagnetic Compatibility - Product Family Standard for Audio, Video, Audio-Visual and Entertainment Lighting Control

Apparatus for Professional Use, Part 1: Emissions

EN 55103-1:1997 Magnetic Field Emissions-Annex A@ 10 cm and 20 cm

EN 55022:2003 Limits and Methods of Measurement of Radio Disturbance Characteristics of ITE: Radiated, Class B Limits; Conducted, Class A

EN 55103-2:1997 Electromagnetic Compatibility - Product Family Standard for Audio, Video, Audio-Visual and Entertainment Lighting Control

Apparatus for Professional Use, Part 2: Immunity

EN 61000-4-2: A2:2001 Electrostatic Discharge Immunity (Environment E2-criteria B, 4 kV Contact, 8 kV Air discharge)

EN 61000-4-3:2003 Radiated, Radio-frequency, Electromagnetic Immunity (Environment E2, criteria A)

EN61000-4-4:2005 Electrical Fast Transient/Burst Immunity (criteria B)

EN 61000-4-5:2001 Surge Immunity (criteria B)

EN 61000-4-6:1996 Immunity to Conducted Disturbances Induced by Radio-Frequency Fields (criteria A)

EN 61000-4-11:2004 Voltage Dips, Short Interruptions and Voltage Variation

UL 6500 2nd Edition 1999 Audio/Video and Musical Instruments Apparatus for Household, Commercial, and Similar General Use

IEC 60065_2001 / EN 60065_2002 + A1:2006 + A11:2008

UL 60065 7th Ed. CAN/CSA 22.2 No.60065_2003

1. This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received,

including interference that may cause undesired operation.

2. Changes or modi cations not expressly approved by the party responsible for compliance could void the user

’ s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body

1. This device complies with Industry Canada

’ s license-exempt RSSs.

Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference

that may cause undesired operation of the device.

2. Changes or modi cations not expressly approved by the party responsible for compliance could void the user

’ s authority to operate the equipment.

´ sent appareil est conforme aux CNR d

’

Industrie Canada applicables aux appareils radio exempts de licence. L

’ ´ e aux deux conditions suivantes :

(1) l

’ appareil ne doit pas produire de brouillage, et

(2) l

’ utilisateur de l

’ appareil doit accepter tout brouillage

radioe lectrique subi, me me si le brouillage est susceptible d

’ en

compromettre le fonctionnement.

”

Congratulations on your purchase of JBL Professional EON600 Series loudspeakers! We know you are anxious to get up and running as fast as possible, which is why you are reading this section. The following will help you get set up as soon as possible.

Your EON600 system should include the following:

1 x EON600 speaker

1 x 10'(3m) IEC Power Cable

1 x Quick Start Guide

1 2 3

1 2 3 4 5

1.

2.

3.

4.

B

E

F

P O W E R

B L U E T O O T H

S Y N C

B O O T

E Q

P R E S E T S

S IG N A L

M A IN

M O N IT O R

S U B

S P E E C H

E O N 6 15

L IM IT S IG N A L

O N O F F

F R O N T L E D

E Q +

G

H

I

K

M

N

M IC

L IN E

G A IN

C H 1

M A S T E R

V O L U M E

G A IN

C H 2

M IC

L IN E

O

IN 1

MODEL: EON615

SERIAL NO:

T H R U

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.

OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

IN 2

430W Max

100-120VAC 50/ 60Hz

230-240VAC 50/ 60Hz

FUSE TYPE: T3.15L250V

FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE FUSE ONLY WITH SAME TYPE OF RATING.

Made in

Mexico

JBL PROFESSIONAL

A HARMAN INTERNATIONAL COMPANY

DESIGNED AND ENGINEERED IN THE USA

L

A

D

1.

2.

3.

1.

2.

3.

G

P

B

C

E

B L U E T O O T H

S Y N C

B O O T

E Q +

0 º 1 8 0

P O L A R IT Y

º

S IG N A L L IM IT P O W E R

M A S T E R V O L U M E

O N O F F

F R O N T L E D

J

L

I

A

D

M

IN 1 IN 2

N

T H R U 1 T H R U 2

O

MODEL: EON618S

SERIAL NO:





430W Max

100-120VAC 50/ 60Hz

230-240VAC 50/ 60Hz



E O N 6 18 S

Made in

China

JBL PROFESSIONAL

NORTHRIDGE, CA. USA



This LED (White) lights to indicate that the speaker is plugged in and switched ON.

result in unpleasant and fatiguing distortion and may lead to premature failure of your speaker system.

Depress this button in order to initiate pairing with your

Bluetooth enable device.

The SIGNAL LEDs (Green) illuminates to indicate a usable signal is present at connected INPUTS.

This LED will illuminate blue to indicate that your Bluetooth connection is established.

Toggles the LED (Blue) on front of speaker On or Off.

Depress this button to reset the pairing with your Bluetooth enabled device without having to turn the speaker off.

The MIC/LINE buttons selects between two sensitivity ranges. The buttons are used to match the input sensitivity with the output level of the devices connected to CH1 or CH2. Depressing the MIC/LINE switch selects

MIC (High Sensitivity).

CAUTION: Before adjusting this switch, be certain to rotate the control fully counter-clockwise.

After the MIC/LINE switch has been depressed, slowly rotate the control clock-wise until the desired volume has been reached.

•

Use the MIC position (depressed) when a microphone is connected.

•

Use the LINE position (disengaged) when a line level source such as an audio mixing console, audio playback device or electronic musical instrument is connected.

Use this button to toggle through the four different settings.

MAIN:

This is the default setting for the EON600 loudspeakers. Use this setting when your EON600 loudspeaker is being used either on a tripod or pole and facing towards your audience.

MONITOR:

Use this setting when your EON600 loudspeaker is being used as a stage monitor facing towards you.

SUB:

Use this setting when your EON600 loudspeaker is being used in conjunction with a separate subwoofer. This preset enables a High

Pass Filter (HPF) set at 100Hz.

SPEECH:

Use this setting when your EON600 loudspeaker is being used for

Speech only or Spoken Word only applications and is facing towards the audience.

Controls the master volume of the unit. By turning the knob counterclockwise you will be lowering the overall volume of the speaker. By turning the control clockwise you will be increasing the overall volume of the speaker.

These balanced inputs accepts a standard XLR (female) connector and also a 1/4

”

TRS phone plug. A broad range of signals from microphones, audio mixing consoles and electronic musical instruments may be connected here. The sensitivity of these inputs are controlled by the MIC/

LINE SWITCHES.

This XLR (male) output connector provides a method of sending audio out to an external source. If signal is present on both inputs, the inputs will be summed and sent out as a 50/50 mix

Once enabled via the app, the EQ+ toggles the applied EQ settings on/off.

Enables the AC power to the unit on and off.

Controls the gain of CH1 & CH2 respectively. By turning the signal counterclockwise you will be lowering the gain of your source material. By turning the control clockwise you will be increasing the gain.

The LIMIT LED (Red) illuminates to indicate that the system is approaching limit. If this LED is on for more than the duration of brief dynamic peaks, the system is being over-driven. Continuously over-driving the system will

Switches the polarity of the subwoofer between 0 and 180 degrees. Useful for correcting summing issues between the subwoofer and the top boxes.

Users should experiment with the switch at both positions and select the best sounding option for their speci c application.

•

1000 Watt

•

26 lbs. / 11.79 kg

•

110

°

H / 60

°

V Coverage

•

1000 Watt

•

33 lbs. / 14.96 kg

•

100

°

H / 60

°

V Coverage

•

1000 Watt

•

39 lbs. / 17.69 kg

•

90

°

H / 60

°

V Coverage

•

1000 Watt

•

78 lbs. / 35.3 kg

System Type:

Maximum SPL Output:

Frequency Range (-10 dB):

Frequency Response (

±

3 dB):

EQ:

Self powered 15

”

, two-way, bass-re ex

127 dB

39 Hz - 20 kHz

50 Hz - 20 kHz

3 Parametric EQ

’ s, High and Low Shelf (Available via Bluetooth app only)

Ampli

� er Design:

System Power Rating:

Input Impedance:

Line Input Gain:

Mic Input Gain:

Connectors:

LED Indicators:

Cooling:

AC Power Input:

High Ef ciency Class D

1000W Peak (700 LF + 300HF); 500W Continuous (350W LF + 150W HF)

20K ohms (Balanced)

In nity to +26.8dB (+14dBu max input level)

In nity to +29dB (in addition to line input gain)

2 x Balanced XLR-1/4

”

combination inputs; 1 x male XLR loop thru out

Power, Bluetooth, EQ Preset, EQ +, Signal CH1, Signal CH2, Limit

Passively Cooled (No Fan)

100-120VAC 50/60Hz; 230-240VAC 50/60Hz

AC Power Consumption (120VAC): 1/8th Power

–

1.14A (Max), 1/4th Power

–

1.71A (Max), 1/3rd Power

–

2.03A (Max)

LF Driver:

HF Driver:

Coverage Pattern:

Crossover Frequency:

1 x JBL 615H 380mm (15

”

) woofer with 2

”

voice coil

1 x JBL 2414H-1 25.4mm (1

”

) annular polymer diaphragm, neodymium compression driver

90

º

H x 60

º

V

1.8kHz

Material:

Suspension / Mounting:

Handles:

Finish:

Grille:

Dimensions (H x W x D):

Gross Weight:

Polypropylene, multi-purpose main & monitor

36mm pole socket with stabilizing screw, 3 x M10 suspension points

One left, one right, one top, one bottom (4 total)

Black Granite

Powder coated perforated steel with acoustically transparent screen backing

707mm x 439mm x 365mm (27.8

”

x 17.3

”

x 14.4

”

)

17.69 kg (39 lbs)

365 mm

14.4 in

707 mm

27.8 in

439 mm

17.3 in

System Type:

Maximum SPL Output:



±

3 dB):

EQ:

Self powered 12

”


126 dB

48 Hz - 20 kHz

57 Hz - 20 kHz

3 Parametric EQ


Ampli

� er Design:


Input Impedance:

Line Input Gain:

Mic Input Gain:

Connectors:

LED Indicators:

Cooling:

AC Power Input:



20K ohms (Balanced)




”




100-120VAC 50/60Hz; 230-240VAC 50/60Hz


–


–


–

2.03A (Max)

LF Driver:

HF Driver:

Coverage Pattern:


1 x JBL 612H 380mm (12 in) woofer

1 x JBL 2414H-1 25.4mm (1 in) polymer diaphragm, neodymium compression driver

100

º

H x 60

º

V nominal

1.8 kHz

Material:


Handles:

Finish:

Grille:


Gross Weight:




Black Granite


664 mm x 380 mm x 316 mm (26.14

“

x 14.96

“

x 12.44

“

)

14.96 kg (33 lbs)

316 mm

12.44 in

664 mm

26.14 in

380 mm

14.96 in

System Type:

Maximum SPL Output:



±

3 dB):

EQ:

Self powered 10

”


124 dB

52 Hz -20 kHz

60 Hz - 20 kHz

3 Parametric EQ


Ampli

� er Design:


Input Impedance:

Line Input Gain:

Mic Input Gain:

Connectors:

LED Indicators:

Cooling:

AC Power Input:



20K ohms (Balanced)




”




100-120VAC 50/60Hz; 230-240VAC 50/60Hz


–


–


–

2.03A (Max)

LF Driver:

HF Driver:

Coverage Pattern:


1 x JBL 610H 322mm (10 in) woofer

1 x JBL 2414H-1 25.4mm (1 in) polymer diaphragm, neodymium compression driver

110

º

H x 60

º

V nominal

1.8 kHz

Material:


Handles:

Finish:

Grille:


Gross Weight:




Black Granite


558 mm x 322 mm x 295 mm (21.968

“

x 12.677

“

x 11.614

“

)

11.79 kg (26 lbs)

295 mm

11.61 in

558 mm

21.97 in

322 mm

12.67 in

System Type:

Maximum SPL Output:



±

3 dB):

EQ:

Self powered 18

”

, subwoofer

134 dB

31 Hz - 150Hz

42 Hz - 150Hz

3 Parametric EQ


Ampli

� er Design:


Input Impedance:

Line Input Gain:

Mic Input Gain:

Connectors:

LED Indicators:

Cooling:

AC Power Input:


1000W Peak, 500W Continuous

22K ohms (Balanced)

0 + 36 dBu

-


”


Front Power, Rear Power , Bluetooth, EQ+, Preset, Signal, Limit


100-120VAC 50/60Hz; 230-240VAC 50/60Hz


–


–


–

2.03A (Max)

LF Driver:


JBL 618H 457mm (18

”

) woofer with 2

”

voice coil

Selectable; 80 Hz, 100 hz, or 120 Hz

Material:


Handles:

Finish:

Grille:


Gross Weight:

Dura ex coated wooden enclosure

M20 Threaded Pole Cup

2

Black Dura ex


582mm x 668mm x 645mm (22.9

”

x 26.3

”

x 25.4

”

)

35.5 kg (78.2 lbs)

T Y P IC A L

E O N 6 1 5

T Y P IC A L

E O N 6 1 2

T Y P IC A L

E O N 6 1 0

Increased High Frequency detail. The Image Control

Waveguide

’ s patent-pending design precisely controls the sound emanating from the EON600 in the vertical and horizontal planes ensuring the representation of your mix is neutral and accurate at the listening position.

JBL

’ s ground breaking new low frequency waveguide features s

B A C K

O S G S O

F R O N T

H O M E S E T T IN G S IN F O

6

0

2 0

1 2

-6

-1 2

-2 0

2 0 4 0

T O N E

8 0 2 0 0 5 0 0 1 K 2 K 5 K 1 0 K 2 0 K

1 0 0 F L A T

2 0

1 2

6

0

-6

G U ITA R : 0 1

0 3

-1 2

B A S S 5 0 P E Q

-2 0

•

•

•

•

•

•

H O M E

2 0

1 2

6

0

-6

-1 2

-2 0

2 0

L O W F R E Q

4 0

M ID G A IN

H IG H Q

8 0 2 0 0 5 0 0 1 K 2 K 5 K 1 0 K 2 0 K

5 0 0 H z

F L A T

2 0 d B

1 0 c t

S E T T IN G S

2 0

1 2

-6

-1 2

6

0

-2 0

IN F O

G U ITA R : 0 1

0 3

•

•

H O M E

6

0

2 0

1 2

-6

-1 2

-2 0

2 0

L O W F R E Q

4 0

M ID G A IN

H IG H Q

8 0 2 0 0 5 0 0 1 K 2 K 5 K 1 0 K 2 0 K

5 0 0 H z

F L A T

2 0 d B

1 0 c t

S E T T IN G S IN F O

The following guidelines will help you achieve optimum sound wherever you use your EON

®

loudspeakers:

For permanent installation applications utilizing the M10 suspension points, JBL Professional recommends the use of three

(3) M10 x 1.5 thread pitch forged shoulder steel eyebolts with an 18-20mm threaded shaft, along with fender washers, rated for overhead suspension. Users unfamiliar with safe rigging practices should not attempt to suspend loudspeakers. Please see https://www.jblpro.com/pub/technote/tn_v1n14.pdf for more information.

For best results try to get the high frequency horn at least 2 to 4 feet above the heads of the audience. If the speakers are too low, the people in the back of the audience will not receive the best quality sound.

Feedback occurs when the microphones pick up sound from the speakers and

“ feed

”

the sound back through the sound system. If space is limited, point the speakers away from the microphones to reduce feedback.

Low-frequency feedback occurs when the output of the speaker is picked up by the tone arm of the turntable and is reampli ed. A heavy, solid turntable base and shock mounting can also reduce this type of feedback in DJ applications.

Spreading speakers throughout these spaces will produce much better sound than trying to compensate with loudness level or equalization. For very long distances, the use of another set of speakers with time delay is recommended.

Stand speakers upright for PA - Tilt the speakers back on the side for stage monitoring. Upright stance provides even coverage over a wide area. EON speakers are also designed with two slanted positions for stage monitoring applications.

B L U E T O O T H

S Y N C

B O O T

E Q

P R E S E T S

M A IN

M O N IT O R

S U B

S P E E C H

P O W E R

O N O F F

F R O N T L E D

E Q +

S IG N A L L IM IT S IG N A L

M IC

L IN E

G A IN

C H 1

M A S T E R

V O L U M E

G A IN

C H 2

M IC

L IN E

IN 1

MODEL: EON615

SERIAL NO:

T H R U





IN 2

430W Max

100-120VAC 50/ 60Hz

230-240VAC 50/ 60Hz



Made in

Mexico

JBL PROFESSIONAL



B L U E T O O T H

S Y N C

B O O T

E Q

P R E S E T S

M A IN

M O N IT O R

S U B

S P E E C H

P O W E R

O N O F F

F R O N T L E D

E Q +


M IC

L IN E

G A IN

C H 1

M A S T E R

V O L U M E

G A IN

C H 2

M IC

L IN E

IN 1

MODEL: EON615

SERIAL NO:

T H R U





IN 2

430W Max

100-120VAC 50/ 60Hz

230-240VAC 50/ 60Hz



Made in

Mexico

JBL PROFESSIONAL



CH1 input set to

“

Mic

”

CH2 input set to

“

Line

”

B L U E T O O T H

S Y N C

B O O T

E Q

P R E S E T S

M A IN

M O N IT O R

S U B

S P E E C H

P O W E R

O N O F F

F R O N T L E D

E Q +


M IC

L IN E

G A IN

C H 1

M A S T E R

V O L U M E

G A IN

C H 2

M IC

L IN E

IN 1

MODEL: EON615

SERIAL NO:

T H R U





IN 2

430W Max

100-120VAC 50/ 60Hz

230-240VAC 50/ 60Hz



Made in

Mexico

JBL PROFESSIONAL

NORTHRIDGE, CA. USA



B L U E T O O T H

S Y N C

B O O T

E Q

P R E S E T S

M A IN

M O N IT O R

S U B

S P E E C H

P O W E R

O N O F F

F R O N T L E D

E Q +


M IC

L IN E

G A IN

C H 1

M A S T E R

V O L U M E

G A IN

C H 2

M IC

L IN E

IN 1

MODEL: EON615

SERIAL NO:

T H R U





IN 2

430W Max

100-120VAC 50/ 60Hz

230-240VAC 50/ 60Hz



Made in

Mexico

JBL PROFESSIONAL

NORTHRIDGE, CA. USA



CH1 input set to

“

Mic

”

CH2 input set to

“

Line

”

B L U E T O O T H

S Y N C

B O O T

E Q

P R E S E T S

M A IN

M O N IT O R

S U B

S P E E C H

P O W E R

O N O F F

F R O N T L E D

E Q +


M IC

L IN E

G A IN

C H 1

M A S T E R

V O L U M E

G A IN

C H 2

M IC

L IN E

IN 1

MODEL: EON615

SERIAL NO:

T H R U





IN 2

430W Max

100-120VAC 50/ 60Hz

230-240VAC 50/ 60Hz



Made in

Mexico

JBL PROFESSIONAL

NORTHRIDGE, CA. USA



B L U E T O O T H

S Y N C

B O O T

E Q

P R ES E T S

M A IN

M O N IT O R

S U B

S P E E C H

P O W E R

O N O F F

F R O N T L E D

E Q +


M IC

L IN E

G A IN

C H 1

M A S T E R

V O L U M E

G A IN

C H 2

M IC

L IN E

IN 1

MODEL: EON615

T H R U





IN 2

430W Max

100-120VAC 50/ 60Hz

230-240VAC 50/ 60Hz



Made in

Mexico

JBL PROFESSIONAL

NORTHRIDGE, CA. USA



B L U E T O O T H

S Y N C

B O O T

E Q +

0

º

1 8 0

P O L A R IT Y

º

S IG N A L L IM IT P O W E R

M A S T E R V O L U M E

O N O F F

F R O N T L E D

IN 1 IN 2

T H R U 1 T H R U 2

MODEL: EON618S

SERIAL NO:





430W Max

100-120VAC 50/ 60Hz

230-240VAC 50/ 60Hz



E O N 6 18 S

Made in

China

JBL PROFESSIONAL

NORTHRIDG E, CA. USA



+

CH1 & CH2 Mic / Line inputs set to

“

Line

”

Symptom Likely Cause What to do

The JBL Limited Warranty on professional loudspeaker products (except for enclosures) remains in effect for ve years from the date of the

� rst consumer purchase. JBL ampli

� and all other JBL products are warranted for two years from the date of original purchase.

Your JBL Warranty protects the original owner and all subsequent owners so long as: A.) Your JBL product has been purchased in the Continental United States, Hawaii or Alaska. (This Warranty does not apply to JBL products purchased elsewhere except for purchases by military outlets. Other purchasers should contact the local JBL distributor for warranty information.); and B.)

The original dated bill of sale is presented whenever warranty service is required.

Except as speci

� ed below, your JBL Warranty covers all defects in material and workmanship. The following are not covered:

Damage caused by accident, misuse, abuse, product modi

� cation or neglect; damage occurring during shipment; damage resulting from failure to follow instructions contained in your Instruction Manual; damage resulting from the performance of repairs by someone not authorized by JBL; claims based upon any misrepresentations by the seller; any JBL product on which the serial number has been defaced, modi

�

JBL will pay all labor and material expenses for all repairs covered by this warranty. Please be sure to save the original shipping cartons because a charge will be made if replacement cartons are requested. Payment of shipping charges is discussed in the next section of this warranty.

If your JBL product ever needs service, write or telephone us at JBL Incorporated (Attn: Customer Service Department), 8500

Balboa Boulevard, PO. Box 2200, Northridge, California 91329 (818/893-8411). We may direct you to an authorized JBL

Service Agency or ask you to send your unit to the factory for repair. Either way, you

’ ll need to present the original bill of sale to establish the date of purchase. Please do not ship your JBL product to the factory without prior authorization. If transportation of your JBL product presents any unusual dif

� culties, please advise us and we may make special arrangements with you.

Otherwise, you are responsible for transporting your product for repair or arranging for its transportation and for payment of any initial shipping charges. However, we will pay the return shipping charges if repairs are covered by the warranty.

ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE

LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY.

JBL

’

S LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT, AT OUR OPTION, OF ANY DEFECTIVE PRODUCT AND SHALL

NOT INCLUDE INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. SOME STATES DO NOT ALLOW LIMITATIONS ON

HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY, FROM STATE TO STATE.

8500 Balboa Blvd. Northridge, CA 91329 USA

JBL Professional

8500 Balboa Blvd.

Northridge, CA 91329

JBL Professional

8500 Balboa Blvd., Dock 15

Northridge, CA 91329

(Do not return product to this address without

�

Monday through Friday

8:00am -5:00pm

Paci

� c Coast Time in the U.S.A.

www.jblproservice.com www.jblpro.com

Contact the JBL Professional Distributor in your area.

A complete list of JBL Professional international distributors is provided at our U.S.A. website: www.jblpro.com

Part Number: 5032132 8/15 8500 Balboa Boulevard Northridge, CA 91329 USA www.jblpro.com

JBL EON 618 S Active Bass Speaker Owner's Manual

Your EON600 system should include the following:

1 x EON600 speaker

1 x 10'(3m) IEC Power Cable

1 x Quick Start Guide

Related manuals

Tymphany HK

2AAGJEON610

JBL Professional

JBL Professional Eon 615

Shenzhen New Chip Intelligence

HDT101 HD DIAG

JBL

EON615-CVR

Fonestar

SM-558

Harman

JBL EON600 Series

Ningbo Cstar Imp Exp

SL272

JBL

EON615

JBL

EON 700

JBL

EON615-CVR-WX

Harman

JBL EON ONE Compact