Adam HM2 Operation Manual

Add to my manuals
8 Pages

advertisement

Adam HM2 Operation Manual | Manualzz
HM2
Home Monitor
Operation manual
english
english / deutsch
Introduction
First of all, we would like to thank you for choosing ADAM Audio!
ADAM Home Monitors are built for maximum quality reproduction and audio perfection.
You have selected a precise, high resolution passive speaker system that allows you
to professionally evaluate audio recordings. We are confident that these monitors can
meet your expectations for faithful sound reproduction.
To enjoy the capabilities of your new speakers, please read the following safety and
warranty considerations before connecting them. Try to become informed about the
speaker placement and the available control factors - the positioning and the acoustic
properties of the control room often play a bigger role than you might think.
The HM2 is a compact near field monitor. It is an ideal tool for small control rooms,
recording vehicles and post-production suites. It is also perfectly suited for situations
where a combination of no-compromise sound reproduction and a small footprint is
required.
The HM2 is a two-way ported passive system that uses a single A.R.T. tweeter and
conventional bass/midrange driver below the crossover frequency of 1.8 kHz.
The use of our exceptional A.R.T. tweeter ensures full compatibility with the latest
expanded high frequency resolution media formats such as DVD Audio and SACD. At
the same time, the HM2 allows you to monitor the low frequency range down to 52 Hz
with a flat response.
We hope very much that you enjoy your new monitors and their unique transducer
design. If you have any questions about this or any of our products, don’t hesitate to
contact us - we will be happy to advise you. The ADAM Audio Team
Quickstart
Your new speaker system will need some hours of playtime to reach its full potential. It
is advised to warm up the monitors a bit before working with them.
When you start listening, keep all panel settings in the tweeter level switch position.
You should listen to various recordings first, especially untreated material that should
sound natural, where only little or no equalization or dynamic correction has been
applied. After some experience you will be better prepared to eventually adapt to your
room’s acoustics.
2
Setting up your speakers
General recommendations for the set up:
The speakers should be positioned on firm ground or a stand. Vibrating parts of nearby
objects can mask the sound.
Normally it is advised to set them up in the vertical position:
Horizontal placement is possible. Please position both tweeter sections either to the
outside or to the inside. You will get the best linear frequency response from different
listening positions.
Obstacles between the speaker and your ear must be avoided. You should be able to
see the speaker completely. Avoid placement near reflective surfaces, too. You will lose
room information!
3
Setting up your speakers
The Tweeter should be positioned approximately at the height of your ears. In case
you need to position the speaker in a significant lower or higher position, the monitor
should be angled accordingly.
Placement of 2 speakers
The ideal placement of two speakers and a listener in a two-channel stereo listening
situation are the corner points of a equilateral triangle (60° angles).
Surround placement
Speaker positioning for multi-channel stereo purposes is ideally based on a circle with
speakers placed at 0° (Center), 30° (Front Right), 110° (Rear Right), 250° (Rear Left),
330° (Front Left), with the listener being the circle’s center (Radius between 0.7-2.0
m). This ITU recommended configuration may vary depending on the purpose of the
listening room (music or film). However, it is recommended to create a symmetrical
listening position with the front side and surround speaker pointing to the listener’s
ear.
The distance to the surrounding walls should be at least 40 cm to avoid early reflections,
which will degrade the sound.
4
A.R.T. Accelerated Ribbon Technology
So far, all loudspeaker drive units, whether they are voice coil driven, electrostatics,
piezos or magnetostatics, act like a piston, moving air in a 1:1 ratio. As the specific
weight of air is much lower than that of the driving mechanics, there is a bad match
between source and load. This is one of the main reasons for the small 1-2% efficiency
of conventional speakers.
All ADAM speaker systems take a completely new approach in kinematics to move air
and overcome this problem.
Based on the original works of Dr. Oskar Heil, who invented his “Air Motion Transformer”
back in 1972, new electrodynamical transducers have been developed. The A.R.T.
tweeter’s and midrange membrane consist of a lamella-like folded diaphragm whose
single folds move according to the alternate current, thus squeezing air in and out (see
Fig. 1).
The A.R.T. principle achieves a 4:1 velocity transformation between driving diaphragm
and driven air, i. e. the air moves in and out four times faster than the folds itself are
moving. This superior “motor” is responsible for the enormous clarity and transient
reproduction and thus their increased efficiency.
Another factor in dynamics is diaphragm area. For practically all drive units, the cone
area you can see is the acoustically active area of the loudspeaker. By folding the A.R.T.
diaphragm into the third dimension as seen from the listener’s position, the acoustically
effective area of the diaphragm is increased by a factor larger than 2.5 (see Fig. 2).
Thus, a smaller movement is needed for a given sound pressure level, enabling the unit
to reach a higher sound pressure level without dynamic compression.
Besides these advantages, the membrane construction in single stripes avoids the
typical break up of stiff domes or cones at higher frequencies and the resultant dynamic
limiting.
Since the A.R.T. membrane is not by a conventional voice coil but an Aluminum stripe
on a very thin Diaphragm, it is extremely light and therefore ideally suited for high
frequency reproduction up to 35kHz. In comparison to magnetostatics and ribbons, the
A.R.T. tweeter offers an above average efficiency of 93dB/W/m, as well as a perfectly
linear impedance of 3.2 ±0.05 Ohms, an equally perfect phase response of ± 1° within
the used bandwidth, a reasonable directivity characteristic and a thermal power
handling that exceeds that of 1” domes by a factor of 2 to 3.
Fig.1
The A.R.T. Principle: moving the air in a
4:1 ratio instead of a 1:1 piston motion
Fig.2
Area comparison between the
unfolded A.R.T. tweeter diaphragm
and a 1” dome tweeter
5
Warranty
ADAM Audio GmbH provides a ten year limited warranty for this product.
Terms and Conditions
This warranty is limited to the repair of the equipment or, if necessary, the
replacement of parts or the product and return shipping within the country
of purchase.
This warranty complements any national/regional law obligations of dealers or national distributors and does not affect your statutory rights as a
customer.
Neither other transportation, nor any other costs, nor any risk for removal,
transportation and installation of products is covered by this warranty.
Products whose serial number have been altered, deleted, removed or made
illegible are excluded from this warranty.
The warranty will not be applicable in cases other than defects in materials
and/or workmanship at the time of purchase and will not be applicable:
a) for damages caused by incorrect installation, connection or packing,
b) for damages caused by any use other than correct use described in the user
manual,
c) for damages caused by faulty or unsuitable ancillary equipment,
d) if repairs or modifications have been executed by an unauthorized person,
e) for damages caused by accidents, lightning, water, fire heat, public disturbances or any other cause beyond the reasonable control of ADAM Audio.
How to claim repairs under warranty
Should service be required, please contact the ADAM Audio dealer where
the product has been purchased.
If the equipment is being used outside the country of purchase, the international shipping costs have to be paid for by the owner of the product.
Service may be supplied by your ADAM Audio national distributor in the country of residence. In this case, the service costs have to be paid for by the
owner of the product whereas the costs for parts to be repaired or replaced
are free of charge. Please visit our website to get the contact details of your
local distributor.
To validate your warranty, you will need a copy of your original sales invoice
with the date of purchase.
6
HM2 Front
HM2 Back
A.R.T. Tweeter
).
7“ HexaCone® woofer
Tweeter level switch:
l= 0
0= -1.5dB
l 0 ll
ll= +1.5dB
Speaker terminal
Bass reflex port (2x)
Technical Data
Woofer/Subwoofer
1
General Data
Basket ø
7.5” / 186 mm
Freq. response
40Hz - 35kHz
ART Tweeter
1
SPL max at 1m
≥ 109dB
Velocity transf. ratio
4:1
Crossover frequencies
1800 Hz
Input terminal
Biwireing
Input impedance
4Ω
Controls
Tweeter level*
0/-1.5dB/+1.5dB
Power handling sin/music
100W/150W
Efficiency
≥ 87dB/W/m
Weight
10kg
Height x Width x Depth
370 x 220 x 320mm
Warranty
10 years
*The level of the tweeter can be varied in 0/-1.5dB/+1.5dB. This will produce a
considerable change in the sound characteristics, and should be used with caution. In
case you have a considerably damped room or if there is a special sound you are after,
this control will serve you well.
7
ADAM Audio GmbH
Ederstr. 16
12059 Berlin
GERMANY
tel: +49 30-863 00 97-0
fax: +49 30-863 00 97-7
email: [email protected]
ADAM Audio UK Ltd.
email: [email protected]
ADAM Audio USA Inc.
email: [email protected]
ADAM Audio China
email: [email protected]
www.adam-audio.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Questions and Answers

What is the frequency response of the Adam HM2?
The Adam HM2 has a frequency response of 40Hz - 35kHz.
What is the maximum sound pressure level (SPL) of the Adam HM2?
The Adam HM2 has a maximum SPL of ≥ 109dB at 1 meter.
What is the crossover frequency of the Adam HM2?
The Adam HM2 has a crossover frequency of 1800 Hz.
What is the power handling capacity of the Adam HM2?
The Adam HM2 has a power handling capacity of 100W continuous / 150W program.
What is the sensitivity of the Adam HM2?
The Adam HM2 has a sensitivity of ≥ 87dB/W/m.
What are the dimensions of the Adam HM2?
The Adam HM2 has dimensions of 370 x 220 x 320mm (HxWxD).
What is the warranty period for the Adam HM2?
The Adam HM2 has a warranty period of 10 years.
What is the function of the tweeter level switch on the Adam HM2?
The tweeter level switch on the Adam HM2 allows you to adjust the level of the tweeter in 0/-1.5dB/+1.5dB increments.

Related manuals

Download PDF

advertisement