SymNet EDGE - AV-iQ
SymNet EDGE
EDGE
SymNet Edge scalable hardware partners with SymNet Composer open architecture software for total design synergy. Networked audio
connections use Dante protocol for ultra low latency. Multiple end user control options complete the system.
Features:
•
Four configurable I/O card slots, up to 16 channels total of local I/O plus 128 (64x64) channels of Dante network audio.
•
Eight logic inputs (or four analog control inputs) and eight logic outputs.
•
Redundant Dante network audio ports on an internal gigabit switch eliminates the need for an external switch in many systems.
Systems using 10 or more Edge mainframes and/or mainframes separated by distances over 100 meters can be implemented with
off-the-shelf gigabit hardware.
•
Ethernet for configuration and control, and RS-232 for third party control systems.
•
User control by Symetrix ARC wall panels, ARC-WEB web app, SymNet SymVue, third-party touch screens.
•
Port for optional redundant external power supply.
Specifications
Processors
1 x Analog Devices SHARC 21489 @ 400 MHz SIMD.
Logic outputs
Low (0V) when active, pulled high (5V) when
inactive.
Raw processing capacity
400 MIPS, 1.6 GFLOPS.
Logic output maximum external
power supply voltage
24 VDC.
Sampling Rate
48 kHz, ± 100 ppm.
Logic output maximum external
power supply current sinking
50 mA.
Frequency Response (A/D/A)
20 Hz – 20 kHz, ± 0.5 dB.
Logic output maximum output
current
10 mA.
Dynamic Range (A/D/A)
> 114 dB, A-weighted.
RS-232 accessory serial I/O
38.4 kbaud (default), 8 data bits, 1 stop bit,
no parity, no flow control wired straightthrough, only pins 2, 3, and 5 required.
Channel Separation (A/D/A)
> 108 dB @ 1 kHz, +24 dBu.
RS-485 serial I/O
38.4 kbaud (default) 8 data bits, 1 stop bit,
no parity, no flow control. May be broken out
of ARC port.
Latency (A/D/A)
0.88 mS, inputs routed to outputs.
Ethernet Cable
Standard CAT5, maximum device to device
length = 100 meters.
Delay memory
80 mono seconds.
Dante Cable
Standard CAT6, maximum device to device
length = 100 meters.
Analog control inputs
0-3.3 VDC.
ARC Cable
Standard CAT5, distance dependent upon
load and number of devices.
Recommended external
control potentiometer
10k Ohm, linear.
Maximum devices per system
32 units per Site File.
Maximum stored presets
1000.
Copyright 2012, Symetrix, Inc. All Rights Reserved. All specifications and features subject to change without notice.
6408 216th Street SW | Mountlake Terrace, WA 98043 USA
T +1.425.778.7728 F +1.425.778.7727 | www.symetrix.co
SymNet EDGE
Shown with (2) Analog Mic/Line Input and (2) Analog Line Output cards.
! Power: Accepts power from detachable IEC power cable (100-
^ Dante (Primary): 1000 Base-T Ethernet port provides 128
@ Aux Power: Locking power plug accepts power from Mean
& Dante (Secondary): 1000 Base-T Ethernet port for redundant
240 VAC, 50-60 Hz, 45 Watts max).
Well power supply part number GS60A24-P1J fitted with a
Switchcraft part number 767K plug or suitable 24 VDC / 2.0
Amp auxiliary power source.
(64x64) channels of Dante network audio.
Dante network audio implementation.
* Ethernet: 10/100 Base-T Ethernet ports for SymNet Composer
host control and 3rd party accessory controllers over IP. Features
auto-crossover sensing for direct device-to-device connections.
# ARC: Distributes power and RS-485 data to one or more ARC
devices.
$ Logic Outputs: Eight (8) logic outputs with four (4) paired
common ground pins. Logic Outputs go low (0V) when active,
and are internally pulled high (5V) when inactive and can drive
external LED indicators directly.
( RS-232: Serial communications interface for 3rd party
accessory controllers. Port Settings: 38.4 kbaud (default), 8
data bits, 1 stop bit, no parity, no flow control.
BA I/O Cards (A-D): Four 4-channel I/O card slots accept any
combination of available cards providing up to 16 channels of
local I/O. Refer to individual I/O card data sheets for details.
% External Control Inputs: Four (4) analog control inputs are
able to be used as 4 potentiometer inputs or as 8 switch inputs
(+3.3 VDC reference voltage supplied).
Mechanical Data
Item
Specifications
Remarks
Space Required
1U (WDH: 18.91 in x 9.5 in x 1.72 in / 48.02 cm x 24.13 cm x
4.37 cm). Depth does not include connector allowance.
Allow at least 3 inch additional clearance for rear panel connections. Additional depth may be
required depending upon your specific wiring and connections.
Electrical
100-240 VAC, 50/60 Hz, 45 Watts maximum universal input
and/or suitable 24 VDC / 2.0 Amp auxillary power source.
No line voltage switching required.
Ventilation
Maximum recommended ambient operating temperature is
30 C / 86 F.
Ensure that the left and right equipment sides are unobstructed (5.08 cm, 2 in. minimum clearance).The ventilation should not be impeded by covering the ventilation openings with items
such as newspapers, tablecloths, curtains, etc.
Shipping Weight
13 lbs. (5.9 kg).
Certifications or
Compliance
UL 60065, cUL 60065, IEC 60065, EN 55103-1, EN 55103-2,
FCC Part 15, RoHS.
Architect and Engineer Specifications: SymNet EDGE.
The device shall provide four I/O card slots accepting any combination of available cards providing up to 16 channels of local I/O. All signal processing, mixing and routing functions
(including I/O levels) shall be controllable via software. Audio inputs and outputs shall be accessed via rear panel 3.81 mm terminal block connectors. Some I/O cards may utilize other
connector types.
Network audio expansion shall be provided by the Dante protocol with a capacity of 128 (64x64) channels. Primary and Secondary Dante network audio connections shall be provided for
redundant network implementation. Connectors shall be gigabit RJ45 utilizing CAT6 cable.
A designer software application shall be provided that operates on a Windows computer, with network interface installed, running Windows® XP or higher operating system. Computer
connection for configuration shall be via the device’s rear panel Ethernet connector. All internal processing shall be digital (DSP). Available DSP components shall include (but not be
limited to) various forms of: mixers, equalizers, filters, crossovers, dynamics/gain controls, routers, delays, remote controls, meters, generators, onboard logic, and diagnostics.
The front panel shall include input and output signal level indicators, I/O card type indicators as well as indicators for POWER, ARC, RS-232, NETWORK, and DANTE (PRIMARY and
SECONDARY). Additionally, a front panel LCD shall display certain system parameters as well as allow editing of network parameters and may be programmed as an ARC for custom
user control via the front panel UP, DOWN, LEFT, RIGHT and ENTER buttons.
External control shall include dedicated software screens as well as preset selection, I/O level control and muting using the optional ARC wall panel remote controls via industry-standard
CAT5 cable with RJ45 connectors. A built-in web server shall provide four instances of ARC-WEB, which allows for user control from nearly any web browser or mobile device. Logic
I/O shall consist of eight contact closure or four potentiometer inputs along with eight logic outputs. The logic outputs may be used to drive LEDs directly or control external relays or
switchers. All program memory shall be non-volatile and provide program security should power fail. The device shall provide an on board real time clock to facilitate automatic, timed
changing of presets and may sync to NTP. Third-party control systems may interface over IP and RS-232 using a published ASCII control protocol.
Audio conversion shall be 24-bit, 48 kHz and internal processing shall be 32-bit or 40-bit floating point, 48 kHz.
The device shall have an IEC power input socket for 120-240 VAC and a captive power input socket for an external 24 VDC supply. The device shall meet UL/CSA and CE safety
requirements and comply with CE and FCC Part 15 emissions limits. The device shall be RoHS compliant. The chassis shall be constructed of cold rolled steel and moulded plastic, and
mount into a standard 19” 1U EIA rack. The device shall be a Symetrix SymNet EDGE.
Copyright 2012, Symetrix, Inc. All Rights Reserved. All specifications and features subject to change without notice.
6408 216th Street SW | Mountlake Terrace, WA 98043 USA
T +1.425.778.7728 F +1.425.778.7727 | www.symetrix.co
SymNet EDGE 4 Channel Analog Input Card
EDGE 4 Channel Analog Input Card
A single Edge frame has four configurable card slots, providing up to 16 channels of local IO. The
analog input card provides four channels of mic/line input with +48 volts phantom power, 54
dB of gain and 24 dB of trim. The inputs are electronically balanced and provided on plug-in
barrier strip connectors. Control of each input includes gain with metering, trim, mute and
signal inversion.
Features:
•
Mic/line input card. Up to 4 cards per frame.
•
+48 volts phantom power.
•
54 dB of mic pre-amp gain.
•
Extended dynamic range of 115 dB.
•
Field swappable by certified technicians.
Specifications
Number of Inputs
Four (4) switchable balanced mic or line level.
CMRR
> 76 dB @ 1 kHz, unity gain.
Connectors
3.81 mm terminal blocks.
Input Impedance
8k Ohms balanced, 4k Ohms unbalanced.
Nominal Input Level
+4 dBu with 20 dB of headroom.
Phantom Power (per input)
+48 VDC @ 10 mA maximum.
Maximum Input Level
+23 dBu.
Dynamic Range
> 115 dB, A-weighted.
Mic Pre-amp Gain
0, 11.8, 24, 44 or 54 dB switchable
with ± 24 dB trim.
THD + Noise
< -94 dB, unweighted; 1 kHz @ +22 dBu
with 0 dB gain.
Mic Pre-Amp EIN
< -127dB with 150 Ohm source impedance.
Latency
0.28 mS.
Mechanical Data
Item
Specifications
Shipping Weight
1 lbs. (0.45 kg)
Certifications or
Compliance
EN 55103-1, EN 55103-2, FCC Part 15, RoHS.
Remarks
Architect and Engineer Specifications: SymNet EDGE 4 Channel Analog Input Card.
The device shall provide four analog mic/line inputs to an EDGE frame that are adjustable from line to mic level with coarse gain, fine trim and phantom power. Up to four of these devices
may be installed in a single EDGE frame for up to sixteen channels of local input. Levels, phantom powers, signal inversions and mutes shall be controllable via software. Audio inputs
shall be accessed via rear panel 3.81 mm terminal block connectors.
Audio conversion shall be 24-bit, 48 kHz. The dynamic range shall not be lower than 115 dB, A-weighted with a maximum input level of +23 dBu.
The device shall comply with CE and FCC Part 15 emissions limits. The device shall be RoHS compliant. The mounting plate shall be constructed of cold rolled steel, and mount into a
SymNet EDGE frame I/O card slot. The device shall be a Symetrix SymNet EDGE 4 Channel Analog Input Card.
Copyright 2012, Symetrix, Inc. All Rights Reserved. All specifications and features subject to change without notice.
6408 216th Street SW | Mountlake Terrace, WA 98043 USA
T +1.425.778.7728 F +1.425.778.7727 | www.symetrix.co
SymNet EDGE 4 Channel Analog Output Card
EDGE 4 Channel Analog Output Card
A single Edge frame has four configurable card slots, providing up to 16 channels of local IO. The
analog output card provides four channels of line level output. The outputs are electronically
balanced and provided on plug-in barrier strip connectors. Control of each output includes
gain with metering and mute.
Features:
•
Line output card. Up to 4 cards per frame.
•
+24 dBu maximum output level.
•
+12 dB to off of gain.
•
Extended dynamic range of 117 dB.
•
Field swappable by certified technicians.
Specifications
Number of Outputs
Four (4) balanced line level.
Output Impedance
300 Ohms balanced, 150 Ohms unbalanced.
Connectors
3.81 mm terminal blocks.
Dynamic Range
> 117 dB, A-weighted.
Nominal Output Level
+4 dBu with 20 dB of headroom.
THD + Noise
< -95 dB, unweighted; 1 kHz @ +22 dBu
with 0 dB gain.
Maximum Output Level
+24 dBu (+22.8 dBu into a 2k Ohm minimum load).
Latency
0.60 mS.
Mechanical Data
Item
Specifications
Shipping Weight
1 lbs. (0.45 kg)
Certifications or
Compliance
EN 55103-1, EN 55103-2, FCC Part 15, RoHS.
Remarks
Architect and Engineer Specifications: SymNet EDGE 4 Channel Analog Output Card.
The device shall provide four analog line outputs to an EDGE frame that are adjustable with fine trim. Up to four of these devices may be installed in a single EDGE frame for up to sixteen
channels of local output. Levels and mutes shall be controllable via software. Audio outputs shall be accessed via rear panel 3.81 mm terminal block connectors.
Audio conversion shall be 24-bit, 48 kHz. The dynamic range shall not be lower than 117 dB, A-weighted with a maximum output level of +24 dBu.
The device shall comply with CE and FCC Part 15 emissions limits. The device shall be RoHS compliant. The mounting plate shall be constructed of cold rolled steel, and mount into a
SymNet EDGE frame I/O card slot. The device shall be a Symetrix SymNet EDGE 4 Channel Analog Output Card.
6408 216th Street SW | Mountlake Terrace, WA 98043 USA
T +1.425.778.7728 F +1.425.778.7727 | www.symetrix.co
SymNet EDGE 4 Channel Digital Input Card
EDGE 4 Channel Digital Input Card
A single Edge frame has four configurable card slots, providing up to 16
channels of local IO. The digital input card provides four channels of digital
input in AES or S/PDIF format and 24 dB of trim. The inputs are provided on
plug-in barrier strip connectors. Control of each input includes metering,
trim, mute and signal inversion.
Features:
•
Digital audio input card. Up to 4 cards per frame.
•
Supports AES/EBU or S/PDIF.
•
Sample rate conversion on all inputs.
•
Sync range of 12 to 96 kHz.
•
Field swappable by certified technicians.
Specifications
Number of Inputs
Two (2) pairs of switchable AES or S/PDIF format (4
channels total).
Dynamic Range
> 128 dB, unweighted.
Connectors
3.81 mm terminal blocks.
THD + Noise
< -125 dB, unweighted.
Nominal Input Level
-20 dBFS (+4 dBu with 20 dB of headroom).
Nominal Sample Rate
48 kHz.
Maximum Input Level
0 dBFS (+24 dBu).
Sample Rate Sync Range
12 to 96 kHz.
Input Impedance
110 Ohms (AES), 75 Ohms (S/PDIF).
Latency
2.1 mS @ 48 kHz.
Mechanical Data
Item
Specifications
Shipping Weight
1 lbs. (0.45 kg)
Certifications or
Compliance
EN 55103-1, EN 55103-2, FCC Part 15, RoHS.
Remarks
Architect and Engineer Specifications: SymNet EDGE 4 Channel Digital Input Card.
The device shall provide two pairs of digital inputs (4 channels total) to an EDGE frame that are adjustable with fine trim and selectable in format between AES or S/PDIF. Up to four of
these devices may be installed in a single EDGE frame for up to sixteen channels of local input. Levels, mutes, inversions and formats shall be controllable via software. Audio inputs shall
be accessed via rear panel 3.81 mm terminal block connectors.
Audio conversion shall be 24-bit, 48 kHz with ability to accept 12 to 96 kHz using a sample rate conversion. The dynamic range shall not be lower than 128 dB, unweighted with a
maximum input level of 0 dBFS (+24 dBu).
The device shall comply with CE and FCC Part 15 emissions limits. The device shall be RoHS compliant. The mounting plate shall be constructed of cold rolled steel, and mount into a
SymNet EDGE frame I/O card slot. The device shall be a Symetrix SymNet EDGE 4 Channel Digital Input Card.
6408 216th Street SW | Mountlake Terrace, WA 98043 USA
T +1.425.778.7728 F +1.425.778.7727 | www.symetrix.co
SymNet EDGE 4 Channel Digital Output Card
EDGE 4 Channel Digital Output Card
A single Edge frame has four configurable card slots, providing up to
16 channels of local IO. The digital output card provides four channels
of digital output in AES or S/PDIF format with clock inputs to sync the
outputs to a sample rate of your preference. The outputs are provided on
plug-in barrier strip connectors. Control of each output includes gain with
metering and mute.
Features:
•
Digital audio output card. Up to 4 cards per frame.
•
Supports AES/EBU or S/PDIF.
•
Nominal output sample rate of 48 kHz.
•
Supports external clock input of 12 to 96 kHz.
•
Field swappable by certified technicians.
Specifications
Number of Outputs
Two (2) pairs of switchable AES or S/PDIF format (4
channels total).
Dynamic Range
> 128 dB, unweighted.
Connectors
3.81 mm terminal blocks.
THD + Noise
< -125 dB, unweighted.
Nominal Output Level
-20 dBFS (+4 dBu with 20 dB of headroom).
Nominal Sample Rate
48 kHz.
Maximum Output Level
0 dBFS (+24 dBu).
Sample Rate Sync Range
12 to 96 kHz.
Output Impedance
110 Ohms (AES), 75 Ohms (S/PDIF).
Latency
2.1 mS @ 48 kHz.
Mechanical Data
Item
Specifications
Shipping Weight
1 lbs. (0.45 kg)
Certifications or
Compliance
EN 55103-1, EN 55103-2, FCC Part 15, RoHS.
Remarks
Architect and Engineer Specifications: SymNet EDGE 4 Channel Digital Output Card.
The device shall provide two pairs of digital outputs (4 channels total) to an EDGE frame that are adjustable with fine trim and selectable in format between AES or S/PDIF. Up to four
of these devices may be installed in a single EDGE frame for up to sixteen channels of local output. Levels, mutes, clock sources and formats shall be controllable via software. Audio
outputs shall be accessed via rear panel 3.81 mm terminal block connectors.
Audio conversion shall be 24-bit, 48 kHz with ability to accept 12 to 96 kHz using an external clock source. The dynamic range shall not be lower than 128 dB, unweighted with a
maximum output level of 0 dBFS (+24 dBu).
The device shall comply with CE and FCC Part 15 emissions limits. The device shall be RoHS compliant. The mounting plate shall be constructed of cold rolled steel, and mount into a
SymNet EDGE frame I/O card slot. The device shall be a Symetrix SymNet EDGE 4 Channel Digital Output Card.
6408 216th Street SW | Mountlake Terrace, WA 98043 USA
T +1.425.778.7728 F +1.425.778.7727 | www.symetrix.co
SymNet EDGE 4 Channel AEC Input Card
EDGE 4 Channel AEC Input Card
A single Edge frame has four configurable card slots, providing up to
16 channels of local IO. The AEC input card provides four channels of
transparent Acoustic Echo Cancellation (AEC), with phantom power, 54
dB of gain and 24 dB of trim. Symetrix’ latest generation AEC provides
wideband processing with tail lengths up to 250 mS, and covergence
times greater that 100 dB/S. Symetrix AEC latency is an industry low 11 mS
and near zero bypassed. Each channel of AEC features discreet reference
inputs and direct outputs for local reinforcement. AEC processing may be
applied to any SymNet system input while still allowing the card’s inputs to
be used. The inputs are electronically balanced using plug-in barrier strip
connectors. Control of each input includes gain with metering, trim, mute,
AEC, noise cancellation, non-linear processing, and AGC (Automatic Gain
Control).
Features:
•
Wideband dedicated processing. Does not consume Edge DSP
resources.
•
Zero-latency direct outputs and discrete reference inputs per AEC channel.
•
AEC processing available to the card’s direct inputs or internally routed sources.
•
11 mS AEC latency, up to 250 mS tail length, and greater than 100 dB/S convergence time.
•
Field swappable by certified technicians.
Specifications
Number of Inputs
Four (4) acoustic echo cancellation.
Input Impedance
8k Ohms balanced, 4k Ohms unbalanced
Connectors
3.81 mm terminal blocks.
Phantom Power
+20 VDC @ 10 mA maximum.
Nominal Input Level
+4 dBu with 20 dB of headroom.
A/D Dynamic Range
< 115 dB, A-weighted.
Maximum Input Level
+23 dBu.
A/D Latency
0.28 mS (direct), 11 mS (AEC enabled).
Mic Pre-amp Gain
0, 11.8, 24, 44 or 54 dB switchable with ± 24 dB
trim.
A/D THD + Noise
<-94 dB, unweighted.
Mic Pre-amp EIN
<-127 dB with 150 Ohm source impedance.
Tail Length
> 250 mS.
CMRR
> 76 dB @ 1 kHz, unity gain.
Convergence Time
> 100 dB/S.
Mechanical Data
Item
Specifications
Shipping Weight
1 lbs. (0.45 kg)
Certifications or
Compliance
EN 55103-1, EN 55103-2, FCC Part 15, RoHS.
Remarks
Architect and Engineer Specifications: SymNet EDGE 4 Channel AEC Input Card.
The device shall provide four acoustic echo cancellation inputs to an EDGE frame with coarse gain, fine trim and phantom power. Up to four of these devices may be installed in a single
EDGE frame for up to sixteen channels of local input. Levels, phantom powers, signal inversions and mutes shall be controllable via software. Audio inputs shall be accessed via rear
panel 3.81 mm terminal block connectors.
Audio conversion shall be 24-bit, 48 kHz. The dynamic range shall not be lower than 115 dB, A-weighted with a maximum input level of +23 dBu.
The device shall comply with CE and FCC Part 15 emissions limits. The device shall be RoHS compliant. The mounting plate shall be constructed of cold rolled steel, and mount into a
SymNet EDGE frame I/O card slot. The device shall be a Symetrix SymNet EDGE 4 Channel AEC Input Card.
6408 216th Street SW | Mountlake Terrace, WA 98043 USA
T +1.425.778.7728 F +1.425.778.7727 | www.symetrix.co
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising