Canon PowerShot SX160 IS User guide | Manualzz
Camera User Guide
Y
P
O
• Make sure you read this guide, including the “Safety
Precautions” section, before using the camera.
• Reading this guide will help you learn to use the camera
properly.
• Store this guide safely so that you can use it in the future.
C
ENGLISH
Package Contents
Before use, make sure the following items are included in the package.
If anything is missing, contact your camera dealer.
AA Alkaline Batteries (x2)
Interface Cable
IFC-400PCU
Camera
Wrist Strap
WS-800
DIGITAL CAMERA
Solution Disk*
(CD-ROM)
Getting Started
Warranty Card
*Contains software and PDF manuals (= 25).
• A memory card is not included (see below).
Y
P
O
Compatible Memory Cards
The following memory cards (sold separately) can be used, regardless of
capacity.
• SD memory cards*
• SDHC memory cards*
• SDXC memory cards
C
*
• Eye-Fi cards
*Conforms to SD specifications. However, not all memory cards have been verified to
work with the camera.
About Eye-Fi Cards
This product is not guaranteed to support Eye-Fi card functions (including
wireless transfer). In case of an issue with an Eye-Fi card, please check
with the card manufacturer.
Also note that an approval is required to use Eye-Fi cards in many countries
or regions. Without approval, use of the card is not permitted. If it is unclear
whether the card has been approved for use in the area, please check with
the card manufacturer.
2
Preliminary Notes and Legal Information
• Take and review some test shots initially to make sure the images were
recorded correctly. Please note that Canon Inc., its subsidiaries and
affiliates, and its distributors are not liable for any consequential damages
arising from any malfunction of a camera or accessory, including memory
cards, that results in the failure of an image to be recorded or to be
recorded in a way that is machine readable.
• Images recorded by the camera are intended for personal use. Refrain
from unauthorized recording that infringes on copyright law, and note that
even for personal use, photography may contravene copyright or other
legal rights at some performances or exhibitions, or in some commercial
settings.
• The camera warranty is valid only in the area of purchase. In case of
camera problems while abroad, return to the area of purchase before
contacting a Canon Customer Support Help Desk.
• Although the LCD monitor is produced under extremely high-precision
manufacturing conditions and more than 99.99% of the pixels meet
design specifications, in rare cases some pixels may be defective or may
appear as red or black dots. This does not indicate camera damage or
affect recorded images.
C
Y
P
O
• The LCD monitor may be covered with a thin plastic film for protection
against scratches during shipment. If covered, remove the film before
using the camera.
• When the camera is used over an extended period, it may become warm.
This does not indicate damage.
Organization of Camera User Guide
The following guides are included, each used for different purposes.
Basic Guide (= 13)
• Gives basic instructions, from initial preparations to shooting, playback,
and saving on a computer
Advanced Guide (= 33)
• Practical guide that introduces other camera basics and describes
shooting and playback options
3
Part Names and Conventions in This Guide
Microphone
Lamp
Lens
Zoom lever
Shooting: <i (telephoto)> /
<j (wide angle)>
Playback: <k (magnify)> /
<g (index)>
Strap mount
Shutter button
C
Power button
Mode dial
Flash
Speaker
Date/time battery holder
Tripod socket
Memory card/battery cover
Lock release switch
DC coupler cable port
Y
P
O
• In this guide, icons are used to represent the corresponding camera
buttons and dials on which they appear or which they resemble.
• The following camera buttons and controls are represented by icons.
<o> Up button on back
<q> Left button on back
<r> Right button on back
<p> Down button on back
<5> Control dial on back
• Shooting modes and on-screen icons and text are indicated in brackets.
• : Important information you should know
• : Notes and tips for expert camera use
• =xx: Pages with related information (in this example, “xx” represents a
page number)
• Instructions in this guide apply to the camera under default settings.
4
Part Names and Conventions in This Guide
Screen (LCD monitor)
<h (Flash up)> button
<b (Exposure compensation)> /
<a (Single image erase)> button
Movie button
<1 (Playback)> button
HDMITM terminal
DIGITAL terminal
<
(ISO speed)> / <
(Filter
image display)> / Up button
C
<e (Macro)> / <f (Manual
focus)> / Left button
Control dial
FUNC./SET button
<h (Flash)> / Right button
<Q (Self-timer)> / Down button
Indicator
<l (Display)> button
<n> button
Y
P
O
zz
Turning the control dial is one way to
choose setting items, switch images, and
perform other operations. Most of these
operations are also possible with the
<o><p><q><r> buttons.
• For convenience, all supported memory cards are simply referred to as
“the memory card”.
• The tabs shown above titles indicate whether the function is used for still
images, movies, or both.
Still Images
: Indicates that the function is used when shooting or
viewing still images.
Movies
: Indicates that the function is used when shooting or
viewing movies.
5
Table of Contents
Package Contents..........................2
Compatible Memory Cards.............2
Preliminary Notes and Legal
Information......................................3
Organization of Camera User Guide..............................................3
Part Names and Conventions in This Guide......................................4
Table of Contents............................6
Contents: Basic Operations............8
Safety Precautions........................10
Basic Guide..................... 13
Initial Preparations........................14
Trying the Camera Out.................20
Included Software, PDF Manuals........................................25
Accessories..................................32
C
Advanced Guide.............. 33
1
Camera Basics......................33
On/Off...........................................34
Shutter Button...............................35
Shooting Modes............................36
Shooting Display Options.............36
FUNC. Menu.................................37
MENU Menu.................................38
Indicator Display...........................40
Clock.............................................40
2
Smart Auto Mode..................41
Shooting (Smart Auto)..................42
Common, Convenient Features....49
Image Customization Features.....54
6
Helpful Shooting Features............59
Customizing Camera Operation......................................62
3
Other Shooting Modes.........65
Brightness/Color Customization (Live View Control)........................66
Specific Scenes............................67
Special Modes for Other Purposes.......................................69
Image Effects (Creative Filters)....71
Discreet Mode...............................76
Shooting Various Movies..............77
4
P Mode...................................79
Y
P
O
Shooting in Program AE Mode (<P> Mode)...................................80
Image Brightness (Exposure
Compensation).............................81
Color and Continuous Shooting....84
Shooting Range and Focusing.....90
Flash.............................................98
Other Settings.............................101
5
Tv, Av, and M Mode.............103
Specific Shutter Speeds (<Tv>
Mode)..........................................104
Specific Aperture Values (<Av>
Mode)..........................................105
Specific Shutter Speeds and
Aperture Values (<M> Mode)......106
6
Playback Mode...................109
Viewing....................................... 110
Browsing and Filtering Images........................................ 114
Image Viewing Options............... 117
Table of Contents
Protecting Images.......................120
Erasing Images...........................124
Rotating Images..........................127
Image Categories.......................129
Editing Still Images.....................133
Editing Movies............................139
7
Setting Menu.......................141
Adjusting Basic Camera Functions....................................142
8
Accessories........................155
Replacing the Date/Time Battery........................................156
Optional Accessories..................157
Using Optional Accessories........159
Printing Images...........................166
Using an Eye-Fi Card.................179
9
C
Y
P
O
Appendix.............................181
Troubleshooting..........................182
On-Screen Messages.................186
On-Screen Information...............188
Functions and Menu Tables........192
Handling Precautions..................202
Specifications..............................203
Index...........................................207
7
Contents: Basic Operations
4 Shoot
zz
Use camera-determined settings (Auto Mode)..................................... 42
Shooting people well
I
P
Portraits
(= 67)
Against Snow
(= 68)
Matching specific scenes
t
Low Light
(= 67)
Applying special effects
Vivid Colors
(= 71)
Miniature Effect
(= 72)
Fireworks
(= 68)
C
Y
P
O
Poster Effect
(= 71)
Fish-Eye Effect
(= 72)
Toy Camera Effect
(= 74)
Monochrome
(= 75)
zz
Where sound and flash are not allowed (Discreet Mode)..................... 76
zz
While adjusting image settings (Live View Control).............................. 66
zz
Focus on faces.......................................................................... 42, 67, 93
zz
With myself in the shot (Self-Timer)................................................ 50, 69
zz
Add date stamps................................................................................... 52
8
Contents: Basic Operations
1 View
zz
View images (Playback Mode).............................................................110
zz
Automatic playback (Slideshow)..........................................................118
zz
On a TV............................................................................................... 159
zz
On a computer...................................................................................... 26
zz
Browse through images quickly...........................................................114
zz
Erase images...................................................................................... 124
E Shoot/View Movies
zz
Shoot movies.................................................................................. 42, 77
zz
View movies (Playback Mode).............................................................110
c Print
Y
P
O
zz
Print pictures....................................................................................... 166
Save
zz
Save images to a computer.................................................................. 26
C
9
Safety Precautions
• Before using the product, please ensure that you read the safety precautions
described below. Always ensure that the product is used correctly.
• The safety precautions noted on the following pages are intended to prevent
injuries to yourself and other persons, or damage to the equipment.
• Be sure to also check the guides included with any separately sold
accessories you use.
Warning
Denotes the possibility of serious injury or death.
• Do not trigger the flash in close proximity to people’s eyes.
Exposure to the intense light produced by the flash could damage eyesight.
In particular, remain at least 1 meter (39 inches) away from infants when
using the flash.
• Store this equipment out of the reach of children and infants.
Strap: Putting the strap around a child’s neck could result in asphyxiation.
Date/time battery: Dangerous if swallowed. If this occurs, contact a doctor
immediately.
Y
P
O
• Use only recommended power sources.
• Do not attempt to disassemble, alter or apply heat to the product.
• Avoid dropping or subjecting the product to severe impacts.
• To avoid the risk of injury, do not touch the interior of the product if
it has been dropped or otherwise damaged.
• Stop using the product immediately if it emits smoke, a strange
smell, or otherwise behaves abnormally.
• Do not use organic solvents such as alcohol, benzine, or thinner to
clean the product.
• Do not let the product come into contact with water (e.g. sea water)
or other liquids.
• Do not allow liquids or foreign objects to enter the camera.
This could result in electrical shock or fire.
If liquids or foreign objects come into contact with the camera interior,
immediately turn the camera off and remove the batteries.
C
• Use only the recommended batteries.
• Do not place the batteries near or in direct flame.
The batteries may explode or leak, resulting in electrical shock or fire. This
could cause injury and damage the surroundings. In the event that batteries
leak and the battery electrolyte contacts eyes, mouth, skin or clothing,
immediately flush with water.
10
Safety Precautions
• Turn the camera off in places where camera use is prohibited.
The electromagnetic waves emitted by the camera may interfere with the
operation of electronic instruments and other devices. Exercise adequate
caution when using the camera in places where use of electronic devices is
restricted, such as inside airplanes and medical facilities.
• Do not play the supplied CD-ROM(s) in any CD player that does not
support data CD-ROMs.
It is possible to suffer hearing loss from listening with headphones to the
loud sounds of a CD-ROM played on an audio CD player (music player).
Additionally, this could damage the speakers.
Caution
Denotes the possibility of injury.
• When holding the camera by the strap, be careful not to bang it,
subject it to strong impacts or shocks, or let it get caught on other
objects.
• Be careful not to bump or push strongly on the lens.
This could lead to injury or damage the camera.
Y
P
O
• Be careful not to subject the screen to strong impacts.
If the screen cracks, injury may result from the broken fragments.
C
• When using the flash, be careful not to cover it with your fingers or
clothing.
This could result in burns or damage to the flash.
• Avoid using, placing or storing the product in the following places:
-Places subject to strong sunlight
-Places subject to temperatures above 40 °C (104 °F)
-Humid or dusty areas
These could cause leakage, overheating or an explosion of the batteries,
resulting in electrical shock, fire, burns or other injuries.
• The slideshow transition effects may cause discomfort when viewed
for prolonged periods.
11
Safety Precautions
Caution
Denotes the possibility of damage to the equipment.
• Do not aim the camera at bright light sources (such as the sun on a
clear day).
Doing so may damage the image sensor.
• When using the camera on a beach or at a windy location, be careful
not to allow dust or sand to enter the camera.
This may cause the product to malfunction.
• In regular use, small amounts of smoke may be emitted from the
flash.
This is due to the high intensity of the flash burning dust and foreign
materials stuck to the front of the unit. Please use a cotton swab to remove
dirt, dust or other foreign matter from the flash to prevent heat build-up and
damage to the unit.
Y
P
O
• Remove and store the batteries when you are not using the camera.
If the batteries are left inside the camera, damage caused by leakage may
occur.
• Before you discard the batteries, cover the terminals with tape or
other insulators.
Contacting other metal materials may lead to fire or explosions.
• Do not charge batteries of different types at the same time, or use
older batteries together with newer batteries.
• Do not insert the batteries with the + and – terminals reversed.
This may cause the product to malfunction.
C
• When putting the camera in your bag, ensure that hard objects do
not come into contact with the screen.
• Do not attach any hard objects to the camera.
Doing so may cause malfunctions or damage the screen.
12
Basic Guide
Gives basic instructions, from initial
preparations to shooting, playback, and
saving on a computer
C
Y
P
O
13
Initial Preparations
Prepare for shooting as follows.
Attaching the Strap
zz
Thread the end of the strap through the
strap hole ( ), and then pull the other
end of the strap through the loop on the
threaded end ( ).
Y
P
O
zz
The strap can also be attached to the left
side of the camera.
C
Holding the Camera
zz
Place the strap around your wrist.
zz
When shooting, keep your arms close to
your body and hold the camera securely
to prevent it from moving. If you have
raised the flash, do not rest your fingers
on it.
14
Initial Preparations
Inserting the Batteries and Memory Card
Insert the included batteries and a memory card (sold separately).
Note that before using a new memory card (or a memory card formatted in
another device), you should format the memory card with this camera (= 146).
1 Check the card’s write-protect
tab.
zz
Recording is not possible on memory cards
with a write-protect tab when the tab is in the
locked (downward) position. Slide the tab up
until it clicks into the unlocked position.
2 Open the cover.
zz
Slide the switch ( ) and open the cover
( ).
C
Y
P
O
3 Insert the batteries.
zz
Insert the batteries as shown.
4 Insert the memory card.
zz
Insert the memory card facing as shown
until it clicks into the locked position.
zz
Make sure the memory card is facing the
right way when you insert it. Inserting
memory cards facing the wrong way may
damage the camera.
Label
15
Initial Preparations
5 Close the cover.
zz
Lower the cover ( ) and hold it down as
you slide it, until it clicks into the closed
position ( ).
Compatible Batteries
Y
P
O
Use AA alkaline batteries or Canon AA NiMH batteries (sold separately,
= 157).
• Due to the inconsistent performance of other batteries, use of specified
batteries only is recommended.
• NiMH batteries last longer in cameras than alkaline batteries do, especially
in cold weather.
• For guidelines on how many shots or hours of recording are possible with
various batteries, see “Specifications” (= 203).
C
Removing the Memory Card
zz
Open the cover and push the memory
card in until it clicks, and then slowly
release the memory card.
XX
The memory card will pop up.
16
Initial Preparations
Setting the Date and Time
Set the current date and time correctly as follows if the [Date/Time] screen
is displayed when you turn the camera on. Information you specify this way
is recorded in image properties when you shoot, and it is used when you
manage images by shooting date or print images showing the date.
You can also add a date stamp to shots, if you wish (= 52).
1 Turn the camera on.
zz
Press the power button.
XX
The [Date/Time] screen is displayed.
2 Set the date and time.
zz
Press the <q><r> buttons to choose an
Y
P
O
option.
zz
Press the <o><p> buttons or turn the
<5> dial to specify the date and time.
zz
When finished, press the <m> button.
C
3 Set the home time zone.
zz
Press the <q><r> buttons or turn the
<5> dial to choose your home time
zone.
4 Finish the setup process.
zz
Press the <m> button when finished.
After a confirmation message, the setting
screen is no longer displayed.
zz
To turn off the camera, press the power button.
17
Initial Preparations
• Unless you set the date, time, and home time zone, the [Date/
Time] screen will be displayed each time you turn the camera on.
Specify the correct information.
• To set daylight saving time (1 hour ahead), choose [
] in step 2 and then
choose [ ] by pressing the <o><p> buttons or turning the <5> dial.
Changing the Date and Time
Adjust the date and time as follows.
1 Access the camera menu.
zz
Press the <n> button.
Y
P
O
2 Choose [Date/Time].
zz
Move the zoom lever to choose the [3]
tab.
zz
Press the <o><p> buttons or turn the
<5> dial to choose [Date/Time], and
then press the <m> button.
C
3 Change the date and time.
zz
Follow step 2 on = 17 to adjust the settings.
zz
Press the <n> button to close the menu.
• Once the date/time battery is depleted, the [Date/Time] screen will be displayed when
you turn the camera on. Follow the steps on = 17 to set the date and time.
• If the [Date/Time] screen is displayed each time you turn the camera on,
even after you have set the date and time correctly, replace the date/time
battery with a new one (= 156).
18
Initial Preparations
Display Language
The display language can be changed as needed.
1 Enter Playback mode.
zz
Press the <1> button.
2 Access the setting screen.
zz
Press and hold the <m> button, and
then immediately press the <n>
button.
3 Set the display language.
Y
P
O
zz
Press the <o><p><q><r> buttons or
turn the <5> dial to choose a language,
and then press the <m> button.
XX
Once the display language has been set,
the setting screen is no longer displayed.
C
• The current time is displayed if you wait too long in step 2 after pressing
the <m> button before you press the <n> button. In this case,
press the <m> button to dismiss the time display and repeat step 2.
• You can also change the display language by pressing the <n> button
] on the [3] tab.
and choosing [Language
19
Still Images
Movies
Trying the Camera Out
Follow these instructions to turn the camera on, shoot still images or
movies, and then view them.
Shooting (Smart Auto)
For fully automatic selection of the optimal settings for specific scenes,
simply let the camera determine the subject and shooting conditions.
1 Turn the camera on.
zz
Press the power button.
XX
The startup screen is displayed.
2 Enter <A> mode.
zz
Set the mode dial to <A>.
zz
Aim the camera at the subject. The
Y
P
O
camera will make a slight clicking noise
as it determines the scene.
XX
Icons representing the scene and image
stabilization mode are displayed in the
upper right of the screen.
XX
Frames displayed around any detected
subjects indicate that they are in focus.
C
3 Compose the shot.
zz
To zoom in and enlarge the subject, move
the zoom lever toward <i> (telephoto),
and to zoom away from the subject, move
it toward <j> (wide angle).
20
Trying the Camera Out
4 Shoot.
Shooting Still Images
Focus.
zz
Press the shutter button lightly, halfway
down. The camera beeps twice after
focusing, and green frames are displayed
to indicate image areas in focus.
zz
If [Raise the flash] appears on the screen,
C
Y
P
O
press the <h> button to raise the flash. It
will fire when shooting. If you prefer not
to use the flash, push it down with your
finger, into the camera.
Shoot.
zz
Press the shutter button all the way
down.
XX
As the camera shoots, a shutter sound
is played, and in low-light conditions, the
flash fires automatically.
zz
Keep the camera still until the shutter
sound ends.
XX
Your shot remains displayed on the
screen for about two seconds.
zz
Even while the shot is displayed, you can
take another shot by pressing the shutter
button again.
21
Trying the Camera Out
Shooting Movies
Start shooting.
zz
Press the movie button. The camera
Elapsed Time
beeps once as recording begins, and [ Rec] is displayed with the elapsed time.
XX
Black bars displayed on the top and
bottom edges of the screen indicate
image areas not recorded.
XX
Frames displayed around any detected
faces indicate that they are in focus.
zz
Once recording begins, you can take your
finger off the movie button.
Finish shooting.
Y
P
O
zz
Press the movie button again to stop
shooting. The camera beeps twice as
recording stops.
C
22
Trying the Camera Out
Viewing
After shooting images or movies, you can view them on the screen as
follows.
1 Enter Playback mode.
zz
Press the <1> button.
XX
Your last shot is displayed.
2 Browse through your images.
zz
To view the previous image, press
the <q> button or turn the <5> dial
counterclockwise. To view the next
image, press the <r> button or turn the
<5> dial clockwise.
zz
Press and hold the <q><r> buttons to
browse through images quickly. Images
appear grainy at this time.
C
Y
P
O
zz
To access Scroll Display mode, turn
the <5> dial rapidly. In this mode,
turn the <5> dial to browse through
images.
zz
To return to single-image display, press
the <m> button.
zz
Movies are identified by a [
play movies, go to step 3.
] icon. To
23
Trying the Camera Out
3 Play movies.
zz
Press the <m> button to access the
Volume
movie control panel, choose [ ] (either
press the <q><r> buttons or turn the
<5> dial), and then press the <m>
button again.
XX
Playback now begins, and after the movie
] is displayed.
is finished, [
zz
To adjust the volume, press the <o><p>
buttons.
• To switch to Shooting mode from Playback mode, press the shutter button
halfway.
Erasing the Images
Y
P
O
You can choose and erase unneeded images one by one. Be careful when
erasing images, because they cannot be recovered.
1 Choose an image to erase.
C
zz
Press the <q><r> buttons or turn the
<5> dial to choose an image.
2 Erase the image.
zz
Press the <a> button.
zz
After [Erase?] is displayed, press the
<q><r> buttons or turn the <5> dial to
choose [Erase], and then press the <m>
button.
XX
The current image is now erased.
zz
To cancel erasure, press the <q><r>
buttons or turn the <5> dial to choose
[Cancel], and then press the <m>
button.
• You can also erase all images at once (= 124).
24
Included Software, PDF Manuals
The software and PDF manuals on the included DIGITAL CAMERA Solution
Disk (CD-ROM) (= 2) are introduced below, with instructions for
installation, and saving images to a computer.
Software
After installing the software on the CD-ROM, you can do the following
things on your computer.
CameraWindow
zz
Import images and change camera settings
ImageBrowser EX
zz
Manage images: view, search, and organize
zz
Print and edit images
Auto Update Function
Using the included software, you can update to the latest version, and
download new functions via the Internet (some software excluded). Be sure
to install the software on a computer with an Internet connection so you can
use this function.
C
Y
P
O
• Internet access is required to use this function, and any ISP
account charges and access fees must be paid separately.
PDF Manuals
Camera User Guide
zz
Refer to this guide for a more in-depth understanding of camera
operation.
Software Guide
zz
Refer to this guide when using the included software. The guide can be
accessed from the help system of included software (some software
excluded).
25
Included Software, PDF Manuals
System Requirements
The included software can be used on the following computers. Adobe
Reader is required to view the PDF manuals.
Windows
Operating
System
Macintosh
Windows 7 SP1
Windows Vista SP2
Windows XP SP3
Mac OS X 10.6 – 10.7
Computer
Computers running one of the above operating systems
(preinstalled), with an included USB port and Internet connection*
Processor
Still images:
1.6 GHz or higher
Movies:
Core 2 Duo 1.66 GHz or higher
Mac OS X 10.7:
Core 2 Duo or higher
Mac OS X 10.6:
Core Duo 1.83 GHz or higher
RAM
Still images
Windows 7 (64 bit): 2 GB or
more
Windows 7 (32 bit), Vista: 1 GB
or more
Windows XP: 512 MB or more
Movies
1 GB or more
Mac OS X 10.7: 2 GB or more
Mac OS X 10.6: 1 GB or more
Interfaces
USB
Free Hard Disk
Space
440 MB or more*
Display
1024 x 768 resolution or higher
C
Y
P
O
550 MB or more
*Silverlight 4 or later (max. 100 MB) must be installed, and in Windows XP, Microsoft
.NET Framework 3.0 or later (max. 500 MB) must be installed. Installation may take
some time, depending on computer performance.
• Check the Canon website for the latest system requirements, including
supported OS versions.
26
Included Software, PDF Manuals
Installing the Software
Windows 7 and Mac OS X 10.6 are used here for the sake of illustration.
Using the software auto update function, you can update to the latest
version and download new functions via the Internet (some software
excluded), so be sure to install the software on a computer with an Internet
connection.
1 Insert the CD-ROM in the
computer’s CD-ROM drive.
zz
Insert the included CD-ROM (DIGITAL
CAMERA Solution Disk) (= 2) in the
computer’s CD-ROM drive.
zz
On a Macintosh computer, after inserting
the disc, double-click the desktop disc icon
to open it, and then double-click the [ ]
icon displayed.
Y
P
O
2 Begin the installation.
zz
Click [Easy Installation] and follow the
C
on-screen instructions to complete the
installation process.
27
Included Software, PDF Manuals
3 When a message is displayed
prompting you to connect
the camera, connect it to a
computer.
zz
With the camera turned off, open the
cover ( ). With the smaller plug of the
included interface cable (= 2) in the
orientation shown, insert the plug fully
into the camera terminal ( ).
zz
Insert the larger plug of the interface
Y
P
O
cable in the computer’s USB port. For
details about USB connections on the
computer, refer to the computer user
manual.
C
4 Install the files.
zz
Turn the camera on, and follow the
on-screen instructions to complete the
installation process.
XX
The software will connect to the Internet
to update to the latest version and
download new functions. Installation may
take some time, depending on computer
performance and the Internet connection.
zz
Click [Finish] or [Restart] on the screen
after installation and remove the CDROM when the desktop is displayed.
zz
Turn the camera off and disconnect the
cable.
28
Included Software, PDF Manuals
• When not connected to the Internet, there are the following limitations.
-The screen in step 3 will not be displayed.
-Some functions may not be installed.
• The first time you connect the camera to the computer, drivers will be
installed, so it may take a few minutes until camera images are accessible.
• If you have several cameras that were bundled with ImageBrowser EX on
the included CD-ROMs, be sure to use each camera with their included CDROM and follow the on-screen installation instructions for each. Doing so will
ensure that each camera will receive the correct updates and new functions
via the auto update function.
Saving Images to a Computer
Windows 7 and Mac OS X 10.6 are used here for the sake of illustration.
1 Connect the camera to the
computer.
Y
P
O
zz
Follow step 3 on = 28 to connect the
camera to a computer.
2 Turn the camera on to access
C
CameraWindow.
zz
Press the <1> button to turn the camera on.
zz
On a Macintosh computer, CameraWindow
is displayed when a connection is established
between the camera and computer.
zz
For Windows, follow the steps introduced
below.
zz
In the screen that displays, click the [
link to modify the program.
]
29
Included Software, PDF Manuals
zz
Choose [Downloads Images From Canon
Camera using Canon CameraWindow]
and then click [OK].
zz
Double click [
CameraWindow
].
3 Save the images to the
computer.
zz
Click [Import Images from Camera], and
Y
P
O
then click [Import Untransferred Images].
XX
Images are now saved to the Pictures
folder on the computer, in separate
folders named by date.
zz
After images are saved, close
CameraWindow, press the <1> button
to turn the camera off, and unplug the
cable.
zz
For instructions on viewing images on
a computer, refer to the Software Guide
(= 25).
C
30
Included Software, PDF Manuals
• In Windows 7, if the screen in step 2 is not displayed, click the [ ] icon in
the taskbar.
• To start CameraWindow in Windows Vista or XP, click [Downloads Images
From Canon Camera using Canon CameraWindow] on the screen displayed
when you turn the camera on in step 2. If CameraWindow is not displayed,
click the [Start] menu and choose [All Programs] ► [Canon Utilities] ►
[CameraWindow] ► [CameraWindow].
• On a Macintosh computer, if CameraWindow is not displayed after step 2,
click the [CameraWindow] icon in the Dock (the bar at the bottom of the
desktop).
• Although you can save images to a computer simply by connecting your
camera to the computer without using the included software, the following
limitations apply.
-It may take a few minutes after you connect the camera to the computer
until camera images are accessible.
-Images shot in vertical orientation may be saved in horizontal orientation.
-Image protection settings may be cleared from images saved to a
computer.
-Some problems may occur when saving images or image information,
depending on the operating system version, the software in use, or image
file sizes.
-Some functions provided by the included software may not be available,
such as editing movies or returning images to the camera.
C
Y
P
O
Using the PDF Manuals
Camera User Guide
zz
Access this guide by double-clicking the desktop shortcut icon.
Software Guide
zz
The guide can be accessed from the help system of included software
(some software excluded).
• It may not be possible to install the PDF manuals on computers that do
not meet the system requirements (= 26). However, you can view the
manuals on a computer that supports Adobe Reader by copying the PDF
files in the Readme folder on the CD-ROM directly to a convenient location
on the computer.
31
Accessories
Included
Accessories
Wrist Strap
WS-800
AA Alkaline
Batteries (x2)
DIGITAL
CAMERA
Solution Disk
Interface Cable IFC-400PCU*1
Memory Card
Card Reader
Flash Unit
Cable
Y
P
O
Windows/
Macintosh
Computer
HDMI Cable HTC-100
High-Power
Flash
HF-DC2*2
Stereo AV Cable AVC-DC400ST
Power
C
TV/
Video System
Canon PictBridge-
Compatible Printers
Battery and AC Adapter Kit
Charger Kit
ACK800*3
CBK4-300
*1Also available for purchase separately.
*2High-Power Flash HF-DC1 also supported.
*3DC Coupler DR-DC10 is required.
Use of genuine Canon accessories is recommended.
This product is designed to achieve excellent performance when used with genuine
Canon accessories.
Canon shall not be liable for any damage to this product and/or accidents such as fire,
etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage
and/or explosion of a battery pack). Please note that this warranty does not apply to
repairs arising out of the malfunction of non-genuine Canon accessories, although you
may request such repairs on a chargeable basis.
32
Advanced Guide
1
Camera Basics
Y
P
O
Practical guide that introduces other camera basics and
describes shooting and playback options
C
33
On/Off
Shooting Mode
zz
Press the power button to turn the
camera on and prepare for shooting.
zz
To turn the camera off, press the power
button again.
Playback Mode
zz
Press the <1> button to turn the camera
on and view your shots.
zz
To turn the camera off, press the <1>
button again.
• To switch to Playback mode from Shooting mode, press the <1> button.
• To switch to Shooting mode from Playback mode, press the shutter button
halfway (= 35).
• The lens will be retracted after about one minute once the camera is in
Playback mode. You can turn the camera off when the lens is retracted by
pressing the <1> button.
Y
P
O
Power-Saving Features (Auto Power Down)
C
As a way to conserve battery power, the camera automatically deactivates
the screen (Display Off) and then turns itself off after a specific period of
inactivity.
Power Saving in Shooting Mode
The screen is automatically deactivated after about one minute of inactivity.
In about two more minutes, the lens is retracted and the camera turns itself
off. To activate the screen and prepare for shooting when the screen is off
but the lens is still out, press the shutter button halfway (= 35).
Power Saving in Playback Mode
The camera turns itself off automatically after about five minutes of
inactivity.
• Adjust the timing of automatic camera and screen deactivation as needed
(= 149).
• Power saving is not active while the camera is connected to a computer
(= 28).
34
Shutter Button
To ensure your shots are in focus, always press the shutter button lightly
(halfway) initially. Once the subject is in focus, press the button all the way
down to shoot.
In this manual, shutter button operations are described as pressing the
button halfway or all the way down.
1 Press halfway. (Press lightly to
focus.)
zz
Press the shutter button halfway. The
camera beeps twice, and AF frames are
displayed around image areas in focus.
2 Press all the way down. (From
the halfway position, press fully
to shoot.)
Y
P
O
XX
The camera shoots, as a shutter sound
is played.
zz
Keep the camera still until the shutter
C
sound ends.
• Images may be out of focus if you shoot without initially pressing
the shutter button halfway.
• Length of shutter sound playback varies depending on the time
required for the shot. It may take longer in some shooting scenes,
and images will be blurry if you move the camera (or the subject
moves) before the shutter sound ends.
35
Shooting Modes
Use the mode dial to access each shooting mode.
Live View Control Mode
Customize image brightness or
colors when shooting (= 66).
P, Tv, Av, and M Modes
Take a variety of shots
using your preferred
settings (= 79, 103).
Auto Mode
Fully automatic shooting, with
camera-determined settings
(= 20, 42).
Movie Mode
For shooting movies
(= 77).
You can also shoot
movies when the mode
dial is not set to Movie
mode, simply by pressing
the movie button.
Special Scene Mode
Shoot with optimal settings for
specific scenes (= 67).
Discreet Mode
Shoot without the flash or camera
sounds (= 76).
Creative Filters Mode
Add a variety of effects to images
when shooting (= 71).
Y
P
O
• You can turn the mode dial to switch to Shooting mode from Playback mode.
C
Shooting Display Options
Press the <l> button to view other information on the screen, or to hide
the information. For details on the information displayed, see = 188.
Information is
displayed
No information is
displayed
• Screen brightness is automatically increased by the night display function
when you are shooting under low light, making it easier to check how shots
are composed. However, on-screen image brightness may not match the
brightness of your shots. Note that any on-screen image distortion or jerky
subject motion will not affect recorded images.
• For playback display options, see = 112.
36
FUNC. Menu
Configure commonly used functions through the FUNC. menu as follows.
Note that menu items and options vary depending on the shooting mode
(= 194 – 195).
1 Access the FUNC. menu.
zz
Press the <m> button.
2 Choose a menu item.
zz
Press the <o><p> buttons to choose a
menu item.
XX
Available options are shown at the bottom
of the screen.
Options
Menu Items
C
Y
P
O
3 Choose an option.
zz
Press the <q><r> buttons or turn the
<5> dial to choose an option.
] icon can
be configured by pressing the <l>
button.
zz
To return to the menu items, press the
<l> button.
zz
Options labeled with a [
4 Finish the setup process.
zz
Press the <m> button.
XX
The screen before you pressed the
<m> button in step 1 is displayed again,
showing the option you configured.
• To undo any accidental setting changes, you can restore the camera’s
default settings (= 152).
37
MENU Menu
Configure a variety of camera functions through other menus as follows.
Menu items are grouped by purpose on tabs, such as shooting [4],
playback [1], and so on. Note that available settings vary depending on
the selected shooting or playback mode (= 196 – 200).
1 Access the menu.
zz
Press the <n> button.
2 Choose a tab.
zz
Move the zoom lever to choose a tab.
zz
After you have pressed the <o><p>
buttons to choose a tab initially, you can
switch between tabs by pressing the
<q><r> buttons.
C
Y
P
O
3 Choose a setting.
zz
Press the <o><p> buttons or turn the
<5> dial to choose a setting.
zz
To choose settings with options not
shown, first press the <m> or <r>
button to switch screens, and then either
press the <o><p> buttons or turn the
<5> dial to select the setting.
zz
To return to the previous screen, press
the <n> button.
38
MENU Menu
4 Choose an option.
zz
Press the <q><r> buttons to choose an
option.
5 Finish the setup process.
zz
Press the <n> button to return to the
screen displayed before you pressed the
<n> button in step 1.
• To undo any accidental setting changes, you can restore the camera’s
default settings (= 152).
C
Y
P
O
39
Indicator Display
The indicator on the back of the camera (= 5) lights up or blinks
depending on the camera status.
Color
Indicator
Status
On
Green
Blinking
Camera Status
Connected to a computer (= 29), or display off
(= 34, 149)
Starting up, recording/reading/transmitting images
• When the indicator blinks green, never turn the camera off, open
the memory card/battery cover, or shake or jolt the camera, which
may corrupt images or damage the camera or memory card.
Clock
You can check the current time.
Y
P
O
zz
Press and hold the <m> button.
XX
The current time appears.
zz
If you hold the camera vertically while
using the clock function, it will switch
to vertical display. Press the <q><r>
buttons or turn the <5> dial to change
the display color.
zz
Press the <m> button again to cancel
the clock display.
C
• When the camera is off, press and hold the <m> button, then press the
power button to display the clock.
40
2
Smart Auto Mode
Y
P
O
Convenient mode for easy shots with greater control
over shooting
C
41
Still Images
Movies
Shooting (Smart Auto)
For fully automatic selection at optimal settings for specific scenes, simply
let the camera determine the subject and shooting conditions.
1 Turn the camera on.
zz
Press the power button.
XX
The startup screen is displayed.
2 Enter <A> mode.
zz
Set the mode dial to <A>.
zz
Aim the camera at the subject. The
camera will make a slight clicking noise
as it determines the scene.
XX
Icons representing the scene and image
stabilization mode are displayed in the
upper right of the screen (= 46, 47).
XX
Frames displayed around any detected
subjects indicate that they are in focus.
C
Y
P
O
3 Compose the shot.
zz
To zoom in and enlarge the subject, move
Zoom Bar
Focus Range (approx.)
42
the zoom lever toward <i> (telephoto),
and to zoom away from the subject, move
it toward <j> (wide angle). (A zoom bar
showing the zoom position is displayed.)
Shooting (Smart Auto)
4 Shoot.
Shooting Still Images
Focus.
zz
Press the shutter button halfway. The
camera beeps twice after focusing, and
green frames are displayed to indicate
image areas in focus.
XX
Several green frames are displayed when
multiple areas are in focus.
zz
If [Raise the flash] appears on the screen,
C
Y
P
O
press the <h> button to raise the flash. It
will fire when shooting. If you prefer not
to use the flash, push it down with your
finger, into the camera.
Shoot.
zz
Press the shutter button all the way
down.
XX
As the camera shoots, a shutter sound
is played, and in low-light conditions
when you have raised the flash, it fires
automatically.
zz
Keep the camera still until the shutter
sound ends.
XX
Your shot remains displayed on the
screen for about two seconds.
zz
Even while the shot is displayed, you can
take another shot by pressing the shutter
button again.
43
Shooting (Smart Auto)
Shooting Movies
Start shooting.
zz
Press the movie button. The camera
Elapsed Time
beeps once as recording begins, and
[●Rec] is displayed with the elapsed time.
XX
Black bars displayed on the top and
bottom edges of the screen indicate
image areas not recorded.
XX
Frames displayed around any detected
faces indicate that they are in focus.
zz
Once recording begins, you can take your
finger off the movie button.
esize the subject and
R
recompose the shot as needed.
Y
P
O
zz
To resize the subject, do the same thing
as in step 3 on = 42. However, note
that the sound of camera operations will
be recorded, and movies shot at zoom
factors shown in blue will look grainy.
zz
When you recompose shots, the
focus, brightness, and colors will be
automatically adjusted.
C
Finish shooting.
zz
Press the movie button again to stop
shooting. The camera beeps twice as
recording stops.
zz
Recording will stop automatically when
the memory card becomes full.
Still Images/Movies
44
• To restore camera sound if you have accidentally deactivated it
(by holding the <l> button down while turning the camera on),
press the <n> button and choose [Mute] on the [3] tab, and
then press the <q><r> buttons to choose [Off].
Shooting (Smart Auto)
Still Images
• A flashing [ ] icon warns that images are more likely to be blurred
by camera shake. In this case, mount the camera on a tripod or
take other measures to keep it still.
• If your shots are dark despite the flash firing, move closer to
the subject. For details on the flash range, see “Specifications”
(= 203).
• The subject may be too close if the camera only beeps once when
you press the shutter button halfway. For details on the focusing
range (shooting range), see “Specifications” (= 203).
• To reduce red-eye and to assist in focusing, the lamp may be
activated when shooting in low-light conditions.
• A blinking [h] icon displayed with the message [Charging the flash]
when you attempt to shoot indicates that shooting is not possible
until the flash has finished recharging. Shooting can resume as
soon as the flash is ready, so either press the shutter button all the
way down and wait, or release it and press it again.
Movies
C
Microphone
Y
P
O
• Keep your fingers away from the
microphone while shooting movies.
Blocking the microphone may prevent
audio from being recorded or may
cause the recording to sound muffled.
• Avoid touching camera controls other than the movie button when
shooting movies, because sounds made by the camera will be
recorded.
• Audio is recorded in stereo.
45
Shooting (Smart Auto)
Still Images
Movies
Scene Icons
In <A> mode, shooting scenes determined by the camera are indicated
by the icon displayed, and corresponding settings are automatically
selected for optimal focusing, subject brightness, and color.
People
Subject
Other Subjects
Icon
In
At Close Background
Color
Motion*1 Range
In
Shadows
Motion*1 on Face*1
Background
Bright
Backlit
Gray
—
With Blue Sky
Backlit
Sunsets
—
Spotlights
Dark
Tripod
Used
Light
Blue
Y
P
O
—
*2
C
—
*2
—
Orange
Dark
Blue
—
*1Not displayed for movies.
*2Displayed in dark scenes when the camera is held still, as when mounted on a tripod.
• Try shooting in <G> mode (= 79) if the scene icon does not
match actual shooting conditions, or if it is not possible to shoot
with your expected effect, color, or brightness.
46
Shooting (Smart Auto)
Still Images
Movies
Image Stabilization Icons
Optimal image stabilization for the shooting conditions is automatically
applied (Intelligent IS). Additionally, the following icons are displayed in
<A> mode.
Image stabilization for still
images
Image stabilization for movies,
reducing strong camera shake,
as when shooting while walking
(Dynamic IS)
Image stabilization for still
images, when panning*
Image stabilization for slow
camera shake, such as when
shooting movies at telephoto
(Powered IS)
Image stabilization for macro
shots (Hybrid IS)
No image stabilization, because
the camera is mounted on
a tripod or held still by other
means
Y
P
O
*Displayed when you pan, following moving subjects with the camera. When you follow
subjects moving horizontally, image stabilization only counteracts vertical camera
shake, and horizontal stabilization stops. Similarly, when you follow subjects moving
vertically, image stabilization only counteracts horizontal camera shake.
C
• To cancel image stabilization, set [IS Mode] to [Off] (= 101). In this case,
an IS icon is not displayed.
47
Shooting (Smart Auto)
Still Images
Movies
On-Screen Frames
A variety of frames are displayed once the camera detects subjects you are
aiming the camera at.
• A white frame is displayed around the subject (or person’s face)
determined by the camera to be the main subject, and gray frames are
displayed around other detected faces. Frames follow moving subjects
within a certain range to keep them in focus.
However, if the camera detects subject movement, only the white frame
will remain on the screen.
• When you are pressing the shutter button halfway and the camera
detects subject movement, a blue frame is displayed, and the focus and
image brightness are constantly adjusted (Servo AF).
• Try shooting in <G> mode (= 79) if no frames are displayed, if
frames are not displayed around desired subjects, or if frames are
displayed on the background or similar areas.
C
48
Y
P
O
Common, Convenient Features
Still Images
Movies
Zooming In Closer on Subjects (Digital Zoom)
When distant subjects are too far away to enlarge using the optical zoom,
use digital zoom for up to about 64x enlargement.
1 Move the zoom lever toward
<i>.
zz
Hold the lever until zooming stops.
XX
Zooming stops at the largest possible zoom
factor (before the image becomes noticeably
grainy), which is then indicated on the screen.
Zoom Factor
2 Move the zoom lever toward
<i> again.
Y
P
O
XX
To continue magnifying the subject, keep
zooming.
C
• Moving the zoom lever will display the zoom bar (which indicates
the zoom position). The color of the zoom bar will change
depending on the zoom range.
-White range: optical zoom range where the image will not appear grainy.
-Yellow range: digital zoom range where the image is not
noticeably grainy (ZoomPlus).
-Blue range: digital zoom range where the image will appear grainy.
Because the blue range will not be available at some resolution
settings (= 55) the maximum zoom factor can be achieved by
following step 1.
• Zoomed images may look grainy, under some resolution settings (= 55)
and zoom factors. In this case, the zoom factor is shown in blue.
• Focal length when optical and digital zoom are combined is as follows
(35mm film equivalent).
28 – 1792 mm (28 – 448 mm with optical zoom alone)
• To deactivate digital zoom, press the <n> button, choose [Digital Zoom]
on the [4] tab, and then choose [Off].
49
Common, Convenient Features
Still Images
Movies
Using the Self-Timer
With the self-timer, you can include yourself in group photos or other timed
shots. The camera will shoot about 10 seconds after you press the shutter
button.
1 Configure the setting.
zz
Press the <p> button, choose []] (either
press the <o><p> buttons or turn the
<5> dial), and then press the <m>
button.
XX
Once the setting is complete, []] is
displayed.
Y
P
O
2 Shoot.
C
zz
For Still Images: Press the shutter button
halfway to focus on the subject, and then
press it all the way down.
zz
For Movies: Press the movie button.
XX
Once you start the self-timer, the lamp
will blink and the camera will play a selftimer sound.
XX
Two seconds before the shot, the blinking
and sound will speed up. (The lamp will
remain lit in case the flash fires.)
zz
To cancel shooting after you have
triggered the self-timer, press the
<n> button.
zz
To restore the original setting, choose [ ] in step 1.
50
Common, Convenient Features
Still Images
Movies
Using the Self-Timer to Avoid Camera Shake
This option delays shutter release until about two seconds after you have
pressed the shutter button. If the camera is unsteady while you are pressing
the shutter button, it will not affect your shot.
Configure the setting.
zz
Follow step 1 on = 50 and choose
[[].
XX
Once the setting is complete, [[] is
displayed.
zz
Follow step 2 on = 50 to shoot.
Still Images
Y
P
O
Movies
Customizing the Self-Timer
You can specify the delay (0 – 30 seconds) and number of shots (1 – 10).
1 Choose [$].
C
zz
Following step 1 on = 50, choose
[$] and press the <n> button
immediately.
2 Configure the setting.
zz
Press the <o><p> buttons to choose
[Delay] or [Shots].
zz
Press the <q><r> buttons or turn the
<5> dial to choose a value, and then
press the <m> button.
XX
Once the setting is complete, [$] is
displayed.
zz
Follow step 2 on = 50 to shoot.
51
Common, Convenient Features
• For movies shot using the self-timer, [Delay] represents the delay
before recording begins, but the [Shots] setting has no effect.
• When you specify multiple shots, image brightness and white balance are
determined by the first shot. More time is required between shots when the
flash fires or when you have specified to take many shots. Shooting will stop
automatically when the memory card becomes full.
• When a delay longer than two seconds is specified, two seconds before the
shot, the lamp blinking and self-timer sound will speed up. (The lamp will
remain lit in case the flash fires.)
Still Images
Adding a Date Stamp
The camera can add the shooting date to images, in the lower-right corner.
However, note that date stamps cannot be edited or removed, so confirm
beforehand that the date and time are correct (= 17).
Y
P
O
1 Configure the setting.
C
zz
Press the <n> button, choose [Date
Stamp] on the [4] tab, and then choose
the desired option (= 38).
XX
Once the setting is complete, [DATE] is
displayed.
2 Shoot.
XX
As you take shots, the camera adds the
shooting date or time to the lower-right
corner of images.
zz
To restore the original setting, choose
[Off] in step 1.
52
Common, Convenient Features
• Date stamps cannot be edited or removed.
• Shots taken without adding a date stamp can be printed with one as follows.
However, adding a date stamp this way to images that already have one may
cause it to be printed twice.
-Use the included software to print
For details, refer to the Software Guide (= 25).
-Print using printer functions (= 166)
-Use camera DPOF print settings (= 173) to print
Still Images
Choosing Subjects to Focus On (Tracking AF)
Shoot after choosing a subject to focus on as follows.
Y
P
O
1 Specify Tracking AF.
zz
Press the <o> button.
XX
[ ] is displayed in the center of the
C
screen.
2 Choose a subject to focus on.
zz
Aim the camera so that [
] is on the
desired subject, and then press the
shutter button halfway.
XX
A blue frame is displayed, and the
camera will keep the subject in focus and
image brightness adjusted (Servo AF).
3 Shoot.
zz
Press the shutter button all the way down
to shoot.
zz
Press the <o> button to cancel Tracking AF.
• Tracking may not be possible when subjects are too small or move too
rapidly, or when subject color or brightness matches that of the background
too closely.
53
Image Customization Features
Still Images
Changing the Aspect Ratio
Change the image aspect ratio (ratio of width to height) as follows.
Configure the setting.
zz
Press the <m> button, choose [
] in
the menu, and choose the desired option
(= 37).
XX
Once the setting is complete, the screen
aspect ratio will be updated.
zz
To restore the original setting, repeat this
process but choose [ ].
Y
P
O
Used for display on widescreen HDTVs or similar display devices.
Same aspect ratio as 35mm film, used for printing images at 5 x 7-inch or
postcard sizes.
C
Native aspect ratio of the camera screen, also used for display on standarddefinition televisions or similar display devices, or for printing images at 3.5 x
5-inch or A-series sizes.
Square aspect ratio.
54
Image Customization Features
Still Images
Changing Image Resolution (Size)
Choose from 4 levels of image resolution, as follows. For guidelines on
how many shots at each resolution setting can fit on a memory card, see
“Specifications” (= 203).
Configure the setting.
zz
Press the <m> button, choose [
] in
the menu, and choose the desired option
(= 37).
XX
The option you configured is now
displayed.
zz
To restore the original setting, repeat this
process but choose [ ].
C
Y
P
O
Guidelines for Choosing Resolution Based on Paper
Size (for 4:3 Images)
A2 (16.5 x 23.4 in.)
zz
[ ]: For e-mailing images.
A3 – A5 (11.7 x
16.5 – 5.8 x 8.3 in.)
5 x 7 in.
Postcard
3.5 x 5 in.
55
Image Customization Features
Still Images
Red-Eye Correction
Red-eye that occurs in the flash photography can be automatically
corrected as follows.
1 Access the [Flash Settings]
screen.
zz
Press the <n> button, choose [Flash
Settings] on the [4] tab, and then press
the <m> button (= 38).
Y
P
O
2 Configure the setting.
C
zz
Choose [Red-Eye Corr.], and then
choose [On] (= 38).
XX
Once the setting is complete, [R] is
displayed.
zz
To restore the original setting, repeat this
process but choose [Off].
• Red-eye correction may be applied to image areas other than
eyes (if the camera misinterprets red eye makeup as red pupils,
for example).
• You can also correct existing images (= 138).
• You can also access the screen in step 2 when the flash is up by pressing
the <r> button and immediately pressing the <n> button.
56
Image Customization Features
Movies
Changing Movie Image Quality
2 image quality settings are available. For guidelines on the maximum
movie length at each level of image quality that will fit on a memory card,
see “Specifications” (= 203).
Configure the setting.
zz
Press the <m> button, choose [
] in
the menu, and choose the desired option
(= 37).
XX
The option you configured is now
displayed.
zz
To restore the original setting, repeat this
process but choose [ ].
Image
Quality
Resolution
1280 x 720
640 x 480
*[
C
Y
P
O
Frame Rate
Details
25 fps*
For shooting in HD
30 fps
For shooting in standard definition
] movies are played back at 30 fps.
• In [ ] mode, black bars displayed on the top and bottom edges of the
screen indicate image areas not recorded.
57
Image Customization Features
Movies
Using the Wind Filter
Distorted audio caused by recording when the wind is strong can be
reduced. However, the recording may sound unnatural when this option is
used when there is no wind.
Configure the setting.
zz
Press the <n> button, choose [Wind Filter] on the [4] tab, and then
choose [On] (= 38).
zz
To restore the original setting, repeat this
process but choose [Off].
C
58
Y
P
O
Helpful Shooting Features
Still Images
Movies
Displaying Grid Lines
Grid lines can be displayed on the screen for vertical and horizontal
reference while shooting.
Configure the setting.
zz
Press the <n> button, choose [Grid Lines] on the [4] tab, and then
choose [On] (= 38).
XX
Once the setting is complete, grid lines
are displayed on the screen.
zz
To restore the original setting, repeat this
process but choose [Off].
Y
P
O
• Grid lines are not recorded in your shots.
C
59
Helpful Shooting Features
Still Images
Magnifying the Area in Focus
You can check the focus by pressing the shutter button halfway, which will
enlarge the portion of the image in focus in the AF frame.
1 Configure the setting.
zz
Press the <n> button, choose [AF-Point Zoom] on the [4] tab, and
then choose [On] (= 38).
Y
P
O
2 Check the focus.
C
zz
Press the shutter button halfway. The
face detected as the main subject is now
magnified.
zz
To restore the original setting, choose
[Off] in step 1.
• The area in focus will not be magnified when you press the shutter
button halfway if a face was not detected, if the person is too close
to the camera and their face is too large for the screen, or if the
camera detects subject movement.
• The display will not magnify when using the digital zoom (= 49) or
Tracking AF (= 94).
60
Helpful Shooting Features
Still Images
Checking for Closed Eyes
[ ] is displayed when the camera detects that people may have closed
their eyes.
1 Configure the setting.
zz
Press the <n> button, choose [Blink Detection] on the [4] tab, and then
choose [On] (= 38).
Y
P
O
2 Shoot.
C
XX
A frame, accompanied by [
], is
displayed when the camera detects a
person whose eyes are closed.
zz
To restore the original setting, choose
[Off] in step 1.
• When you have specified multiple shots in [$] mode, this function is only
available for the final shot.
• The frame is not displayed when [Review] is set to [Quick] (= 63).
61
Customizing Camera Operation
Customize shooting functions on the [4] tab of the menu as follows.
For instructions on menu functions, see “MENU Menu” (= 38).
Still Images
Deactivating the AF Assist Beam
You can deactivate the lamp that normally lights up to help you focus when
you press the shutter button halfway in low-light conditions.
Configure the setting.
zz
Press the <n> button, choose [AF-assist Beam] on the [4] tab, and
then choose [Off] (= 38).
zz
To restore the original setting, repeat this
process but choose [On].
Y
P
O
Still Images
Deactivating the Red-Eye Reduction Lamp
You can deactivate the red-eye reduction lamp that lights up to reduce redeye when the flash is used in low-light shots.
C
1 Access the [Flash Settings]
screen.
zz
Press the <n> button, choose [Flash Settings] on the [4] tab, and then
press the <m> button (= 38).
2 Configure the setting.
zz
Choose [Red-Eye Lamp], and then
choose [Off] (= 38).
zz
To restore the original setting, repeat this
process but choose [On].
62
Customizing Camera Operation
Still Images
Changing the Image Display Period After Shots
Change how long images are displayed after shots as follows.
Configure the setting.
zz
Press the <n> button, choose
[Review] on the [4] tab, and then
choose the desired option (= 38).
zz
To restore the original setting, repeat this
process but choose [2 sec.].
Quick
Displays images only until you can shoot again.
2 – 10 sec.
Displays images for the specified time.
Hold
Displays images until you press the shutter button halfway.
Off
No image display after shots.
C
Y
P
O
63
Customizing Camera Operation
Still Images
Changing the Image Display Style After Shots
Change the way images are displayed after shots as follows.
Configure the setting.
zz
Press the <n> button, choose
[Review Info] on the [4] tab, and then
choose the desired option (= 38).
zz
To restore the original setting, repeat this
process but choose [Off].
Off
Displays only the image.
Detailed
Displays shooting details (= 190).
Focus Check
Shows the area in the AF frame magnified, enabling you to check the
focus. Follow the steps in “Checking the Focus” (= 113).
Y
P
O
• This setting is set to [Off] and cannot be changed when [Review] (= 63) is
set to [Quick] or [Off].
C
64
3
Other Shooting Modes
Y
P
O
Shoot more effectively in various scenes, and take shots
enhanced with unique image effects or captured using
special functions
C
65
Still Images
Movies
Brightness/Color Customization
(Live View Control)
Image brightness or colors when shooting can be easily customized as
follows.
1 Enter <
> mode.
zz
Set the mode dial to <
>.
2 Configure the setting.
zz
Press the <m> button to access the
setting screen. Press the <o><p>
buttons to choose a setting item, and
then press the <q><r> buttons or turn
the <5> dial to adjust the value as you
watch the screen.
zz
Press the <m> button.
Y
P
O
3 Shoot.
C
Brightness
For brighter images, adjust the level to the right, and for darker
images, adjust it to the left.
Color
For more vivid images, adjust the level to the right, and for more
subdued images, adjust it to the left.
Tone
For a warm, reddish tone, adjust the level to the right, and for a cool,
bluish tone, adjust it to the left.
66
Specific Scenes
Choose a mode matching the shooting scene, and the camera will
automatically configure the settings for optimal shots.
1 Enter <K> mode.
zz
Set the mode dial to <K>.
2 Choose a shooting mode.
zz
Press the <m> button, choose [I] in the
menu, and then choose a shooting mode
(= 37).
Y
P
O
3 Shoot.
Still Images
Movies
IShoot portraits (Portrait)
C
zz
Take shots of people with a softening
effect.
Still Images
Shoot under low light (Low Light)
zz
Shoot with minimal camera shake and
subject blur even in low-light conditions.
67
Specific Scenes
Still Images
Movies
PShoot with snowy backgrounds
(Snow)
zz
Bright, natural-colored shots of people
against snowy backgrounds.
Still Images
Movies
tShoot fireworks (Fireworks)
zz
Vivid shots of fireworks.
Y
P
O
• In [t] mode, mount the camera on a tripod or take other
measures to keep it still and prevent camera shake. Additionally,
you should set [IS Mode] to [Off] when using a tripod or other
means to hold the camera still (= 101).
• [
68
] mode resolution is [
C
] (2304 x 1728) and cannot be changed.
Special Modes for Other Purposes
Still Images
Using the Face Self-Timer
The camera will shoot about two seconds after detecting that the face of another
person (such as the photographer) has entered the shooting area (= 93). This
is useful when including yourself in group photos or similar shots.
1 Choose [ ].
zz
Follow steps 1 – 2 on = 67 and
choose [
].
2 Compose the shot and press
the shutter button halfway.
Y
P
O
zz
Make sure a green frame is displayed
C
around the face you focus on and white
frames around other faces.
3 Press the shutter button all the
way down.
XX
The camera now enters shooting standby
mode, and [Look straight at camera to
start count down] is displayed.
XX
The lamp blinks and the self-timer sound
is played.
4 Join the subjects in the shooting
area and look at the camera.
XX
After the camera detects a new face, the
lamp blinking and self-timer sound will
speed up. (When the flash fires, the lamp
will remain lit.) About two seconds later,
the camera will shoot.
zz
To cancel shooting after you have triggered
the self-timer, press the <n> button.
69
Special Modes for Other Purposes
• Even if your face is not detected after you join the others in the shooting
area, the camera will shoot about 15 seconds later.
• To change the number of shots, after choosing [ ] in steps 1 – 2 on
= 69, press the <l> button, and then either press the <q><r>
buttons or turn the <5> dial to choose a value, and then press the <l>
button again.
C
70
Y
P
O
Image Effects (Creative Filters)
Add a variety of effects to images when shooting.
1 Enter < > mode.
zz
Set the mode dial to <
>.
2 Choose a shooting mode.
zz
Press the <m> button, choose [
] in
the menu, and then choose a shooting
mode (= 37).
3 Shoot.
Y
P
O
Still Images
C
Movies
Shoot in vivid colors (Super Vivid)
zz
Shots in rich, vivid colors.
Still Images
Movies
Posterized shots (Poster Effect)
zz
Shots that resemble an old poster or
illustration.
• In [ ] and [ ] modes, try taking some test shots first, to make
sure you obtain the desired results.
71
Image Effects (Creative Filters)
Still Images
Shooting with a Fish-Eye Lens Effect (Fish-eye Effect)
Shoot with the distorting effect of a fish-eye lens.
1 Choose [ ].
zz
Follow steps 1 – 2 on = 71 and
choose [
].
2 Choose an effect level.
zz
Press the <l> button, choose an
effect level (either press the <q><r>
buttons or turn the <5> dial), and then
press the <l> button again.
XX
A preview is shown of how your shot will
look with the effect applied.
Y
P
O
3 Shoot.
C
• Try taking some test shots first, to make sure you obtain the
desired results.
Still Images
Movies
Shots Resembling Miniature Models (Miniature Effect)
Creates the effect of a miniature model, by blurring image areas above and
below your selected area.
You can also make movies that look like scenes in miniature models by
choosing the playback speed before the movie is recorded. People and
objects in the scene will move quickly during playback. Note that sound is
not recorded.
1 Choose [ ].
zz
Follow steps 1 – 2 on = 71 and
choose [
].
XX
A white frame is displayed, indicating the
image area that will not be blurred.
72
Image Effects (Creative Filters)
2 Choose the area to keep in
focus.
zz
Press the <l> button.
zz
Move the zoom lever to resize the frame,
and press the <o><p> buttons to move
it.
3 For movies, choose the movie
playback speed.
zz
Press the <n> button, and then
choose the speed by pressing the
<q><r> buttons or turning the <5>
dial.
Y
P
O
4 Return to the shooting screen
and shoot.
zz
Press the <n> button to return to the
C
shooting screen, and then shoot.
Playback Speed and Estimated Playback Time (for OneMinute Clips)
Speed
Playback Time
Approx. 12 sec.
Approx. 6 sec.
Approx. 3 sec.
• The zoom is not available when shooting movies. Be sure to set
the zoom before shooting.
• Try taking some test shots first, to make sure you obtain the
desired results.
73
Image Effects (Creative Filters)
• To switch the orientation of the frame (from horizontal to vertical or viceversa), press the <m> button in step 2. You can move the frame in vertical
orientation by pressing the <q><r> buttons.
• Holding the camera vertically will change the orientation of the frame.
• Movie image quality is [ ] at an aspect ratio of [ ] and [ ] at an aspect
ratio of [ ] (= 54). These quality settings cannot be changed.
Still Images
Shooting with a Toy Camera Effect
(Toy Camera Effect)
This effect makes images resemble shots from a toy camera by vignetting
(darker, blurred image corners) and changing the overall color.
1 Choose [ ].
Y
P
O
zz
Follow steps 1 – 2 on = 71 and
choose [
].
2 Choose a color tone.
C
zz
Press the <l> button, choose a color
tone (either press the <q><r> buttons or
turn the <5> dial), and then press the
<l> button again.
XX
A preview is shown of how your shot will
look with the effect applied.
3 Shoot.
Standard
Shots resemble toy camera images.
Warm
Images have a warmer tone than with [Standard].
Cool
Images have a cooler tone than with [Standard].
• Try taking some test shots first, to make sure you obtain the
desired results.
74
Image Effects (Creative Filters)
Still Images
Movies
Shooting in Monochrome
Shoot images in black and white, sepia, or blue and white.
1 Choose [ ].
zz
Follow steps 1 – 2 on = 71 and
choose [
].
2 Choose a color tone.
zz
Press the <l> button, choose a color
tone (either press the <q><r> buttons or
turn the <5> dial), and then press the
<l> button again.
XX
A preview is shown of how your shot will
look with the effect applied.
Y
P
O
3 Shoot.
B/W
Black and white shots.
Sepia
Sepia tone shots.
Blue
Blue and white shots.
C
75
Still Images
Movies
Discreet Mode
Shoot without activating camera sounds, the flash, or lamp as follows. Use
this mode where camera sounds, the flash, and lights are prohibited.
1 Enter < > mode.
zz
Set the mode dial to <
>.
2 Shoot.
• In < > mode, even playback sounds are muted. Sounds of camera
operations are muted, and movie audio is also muted.
C
76
Y
P
O
Movies
Shooting Various Movies
Movies
Shooting Movies in <E> Mode
1 Enter <E> mode.
zz
Set the mode dial to <E>.
XX
Black bars displayed on the top and
bottom edges of the screen indicate
image areas not recorded.
2 Configure the settings to suit
the movie (= 192 – 199).
3 Shoot.
zz
Press the movie button.
zz
To stop movie recording, press the movie
Y
P
O
button again.
C
Movies
Locking or Changing Image Brightness Before Shooting
Before shooting, you can lock the exposure or change it in 1/3-stop
increments within a range of –2 to +2.
1 Lock the exposure.
zz
After releasing the shutter button, press
the <o> button to lock the exposure. The
exposure shift bar is displayed.
zz
To unlock the exposure, press the <o>
button again.
2 Adjust the exposure.
zz
Turn the <5> dial to adjust the
exposure, as you watch the screen.
3 Shoot.
77
Shooting Various Movies
Movies
Shooting iFrame Movies
Shoot movies that can be edited with iFrame-compatible software or
devices. You can quickly edit, save, and manage iFrame movies using the
included software (= 25).
1 Choose [ ].
zz
Set the mode dial to <E>.
zz
Press the <m> button, choose [E]
in the menu, and then choose [ ]
(= 37).
XX
Black bars displayed on the top and
bottom edges of the screen indicate
image areas not recorded.
Y
P
O
2 Shoot (= 77).
• The resolution is [ ] (= 57) and cannot be changed.
• iFrame is a video format developed by Apple.
C
78
4
P Mode
Y
P
O
More discerning shots, in your preferred shooting style
C
• Instructions in this chapter apply to the camera with the mode dial set to
<G> mode.
• <G>: Program AE; AE: Auto Exposure
• Before using a function introduced in this chapter in modes other than
<G>, make sure the function is available in that mode (= 192 – 199).
79
Still Images
Movies
Shooting in Program AE Mode
(<P> Mode)
You can customize many function settings to suit your preferred shooting
style.
1 Enter <G> mode.
zz
Set the mode dial to <G>.
2 Customize the settings as
desired (= 81 – 101), and
then shoot.
Y
P
O
• If adequate exposure cannot be obtained when you press the shutter button
halfway, shutter speeds and aperture values are displayed in orange. To
obtain adequate exposure, try adjusting the following settings.
-Activate the flash (= 98)
-Change the ISO speed (= 82)
C
• Movies can be recorded in <G> mode as well, by pressing the movie button.
However, some <H> and <n> settings may be automatically
adjusted for movie recording.
• For details on the shooting range in <G> mode, see “Specifications”
(= 203).
80
Image Brightness (Exposure
Compensation)
Still Images
Movies
Adjusting Image Brightness (Exposure Compensation)
The standard exposure set by the camera can be adjusted in 1/3-stop
increments, in a range of –2 to +2.
zz
Press the <b> button. As you watch the
screen, press the <q><r> buttons or turn
the <5> dial to adjust brightness, and then
press the <b> button again when finished.
XX
The correction level you specified is now
displayed.
Y
P
O
Still Images
Locking Image Brightness/Exposure (AE Lock)
Before shooting, you can lock the exposure, or you can specify focus and
exposure separately.
C
1 Lock the exposure.
zz
Aim the camera at the subject to shoot with
the exposure locked. With the shutter button
pressed halfway, press the <b> button.
XX
[ ] is displayed, and the exposure is locked.
zz
To unlock AE, release the shutter button
and press the <b> button again. In this
case, [ ] is no longer displayed.
2 Compose the shot and shoot.
zz
After one shot, AE is unlocked and [
no longer displayed.
] is
• AE: Auto Exposure
• After the exposure is locked, you can adjust the combination of shutter
speed and aperture value by turning the <5> dial (Program Shift).
81
Image Brightness (Exposure Compensation)
Still Images
Changing the Metering Method
Adjust the metering method (how brightness is measured) to suit shooting
conditions as follows.
zz
Press the <m> button, choose [
] in
the menu, and choose the desired option
(= 37).
XX
The option you configured is now
displayed.
Evaluative
For typical shooting conditions, including backlit shots.
Automatically adjusts exposure to match the shooting conditions.
Y
P
O
Determines the average brightness of light across the entire
Center
image area, calculated by treating brightness in the central area
Weighted Avg.
as more important.
Spot
Metering restricted to within the [ ] (Spot AE Point frame),
displayed in the center of the screen.
C
Still Images
Changing the ISO Speed
zz
Press the <o> button, choose an option
(either press the <o><p> buttons or
turn the <5> dial), and then press the
<m> button.
XX
The option you configured is now
displayed.
82
Image Brightness (Exposure Compensation)
Automatically adjusts the ISO speed to suit the
shooting mode and conditions.
Low For shooting outdoors in fair weather.
For shooting in cloudy conditions, or at twilight.
High
For shooting night scenes, or in dark rooms.
• To view the automatically set ISO speed when the camera is set to [ ],
press the shutter button halfway.
• Although choosing a lower ISO speed may reduce image graininess, there
may be a greater risk of subject blurriness in some shooting conditions.
• Choosing a higher ISO speed will increase shutter speed, which may reduce
subject blurriness and increase the flash range. However, shots may look grainy.
Y
P
O
Still Images
Correcting Image Brightness (i-Contrast)
Before shooting, excessively bright or dark image areas (such as faces or
backgrounds) can be detected and automatically adjusted to the optimal
brightness. Insufficient overall image contrast can also be automatically
corrected before shooting to make subjects stand out better.
C
zz
Press the <n> button, choose
[i-Contrast] on the [4] tab, and then
choose [Auto] (= 38).
XX
Once the setting is complete, [@] is
displayed.
• Under some shooting conditions, correction may be inaccurate or
may cause images to appear grainy.
• You can also correct existing images (= 137).
83
Color and Continuous Shooting
Still Images
Movies
Adjusting White Balance
By adjusting white balance (WB), you can make image colors look more
natural for the scene you are shooting.
zz
Press the <m> button, choose [
] in
the menu, and choose the desired option
(= 37).
XX
The option you configured is now
displayed.
84
Auto
Automatically sets the optimal white balance for the shooting
conditions.
Day Light
For shooting outdoors in fair weather.
Cloudy
For shooting in cloudy conditions, in the shade, or at twilight.
Tungsten
For shooting under ordinary incandescent (tungsten) lighting
and similarly colored fluorescent lighting.
Fluorescent
For shooting under warm-white (or similarly colored) or coolwhite fluorescent lighting.
Fluorescent H
For shooting under daylight fluorescent and similarly colored
fluorescent lighting.
Custom
For manually setting a custom white balance (= 85).
C
Y
P
O
Color and Continuous Shooting
Still Images
Movies
Custom White Balance
For image colors that look natural under the light in your shot, adjust white
balance to suit the light source where you are shooting. Set the white
balance under the same light source that will illuminate your shot.
zz
Follow the steps on = 84 to choose [
].
zz
Aim the camera at a plain white subject,
so that the entire screen is white. Press
the <l> button.
XX
The tint of the screen changes once the
white balance data has been recorded.
• Colors may look unnatural if you change camera settings after
recording white balance data.
C
Y
P
O
85
Color and Continuous Shooting
Still Images
Movies
Changing Image Color Tones (My Colors)
Change image color tones as desired, such as converting images to sepia
or black and white.
zz
Press the <m> button, choose [
] in
the menu, and choose the desired option
(= 37).
XX
The option you configured is now
displayed.
My Colors Off
86
―
Vivid
Emphasizes contrast and color saturation, making images
sharper.
Neutral
Tones down contrast and color saturation for subdued
images.
Sepia
Creates sepia tone images.
B/W
Creates black and white images.
Positive Film
Combines the effects of Vivid Blue, Vivid Green, and
Vivid Red to produce intense yet natural-looking colors
resembling images on positive film.
C
Y
P
O
Lighter Skin Tone
Lightens skin tones.
Darker Skin Tone
Darkens skin tones.
Vivid Blue
Emphasizes blues in images. Makes the sky, ocean, and
other blue subjects more vivid.
Vivid Green
Emphasizes greens in images. Makes mountains, foliage,
and other green subjects more vivid.
Vivid Red
Emphasizes reds in images. Makes red subjects more
vivid.
Custom Color
Adjust contrast, sharpness, color saturation, and other
qualities as desired (= 87).
Color and Continuous Shooting
• White balance (= 84) cannot be set in [ ] or [ ] modes.
• With [ ] and [ ] modes, colors other than people’s skin tone
may be modified. These settings may not produce the expected
results with some skin tones.
Still Images
Movies
Custom Color
Choose the desired level of image contrast, sharpness, color saturation,
red, green, blue, and skin tones in a range of 1 – 5.
1 Access the setting screen.
zz
Follow the steps on = 86 to choose [
], and then press the <l> button.
Y
P
O
2 Configure the setting.
C
zz
Press the <o><p> buttons to choose
an option, and then specify the value by
pressing the <q><r> buttons or turning
the <5> dial.
zz
For stronger/more intense effects (or
darker skin tones), adjust the value to
the right, and for weaker/lighter effects
(or lighter skin tones), adjust the value to
the left.
zz
Press the <l> button to complete the
setting.
87
Color and Continuous Shooting
Still Images
Continuous Shooting
Hold the shutter button all the way down to shoot continuously.
For details on the continuous shooting speed, see “Specifications” (= 203).
1 Configure the setting.
zz
Press the <m> button, choose [
] in
the menu, and choose the desired option
(= 37).
XX
The option you configured is now
displayed.
2 Shoot.
XX
Hold the shutter button all the way down
Y
P
O
to shoot continuously.
Mode
W Continuous
Description
Continuous shooting, with the focus and exposure determined
when you press the shutter button halfway.
C
Continuous
Shooting AF
Continuous shooting and focusing.
[AF Frame] is set to [Center] and cannot be changed.
Continuous
Shooting LV*
Continuous shooting, with the focus fixed at the position
determined in manual focusing. In [t] mode, focus is determined
by the first shot.
*In [t] mode (= 68), AF lock (= 97), or manual focus mode (= 90), [ ] is changed to [ ].
*For details on the continuous shooting speed in each mode, see “Specifications”
(= 203).
88
Color and Continuous Shooting
• Cannot be used with the self-timer (= 50) or [Blink Detection]
(= 61).
• Shooting may stop momentarily or continuous shooting may slow
down depending on shooting conditions, camera settings, and the
zoom position.
• As more shots are taken, shooting may slow down.
• Shooting may slow down if the flash fires.
• Continuous shooting is faster in [
C
] mode (= 67).
Y
P
O
89
Shooting Range and Focusing
Still Images
Shooting Close-ups (Macro)
To restrict the focus to subjects at close range, set the camera to [e]. For
details on the focusing range, see “Specifications” (= 203).
zz
Press the <q> button, choose [e] (either
press the <q><r> buttons or turn the
<5> dial), and then press the <m>
button.
XX
Once the setting is complete, [e] is
displayed.
• In the yellow bar display area below the zoom bar, [e] will turn
gray and the camera will not focus.
Y
P
O
• To prevent camera shake, try mounting the camera on a tripod and shooting
with the camera set to [[] (= 51).
C
Still Images
Movies
Shooting in Manual Focus Mode
When focusing is not possible in AF mode, use manual focus. You can
specify the general focal position and then press the shutter button halfway
to have the camera determine the optimal focal position near the position
you specified. For details on the focusing range, see “Specifications”
(= 203).
1 Choose [f].
zz
Press the <q> button, choose [f]
(either press the <q><r> buttons or turn
the <5> dial), and then press the <m>
button.
XX
[f] and the MF indicator are displayed.
90
Shooting Range and Focusing
2 Specify the general focal
position.
zz
Referring to the on-screen MF indicator
bar (which shows the distance and focal
position) and the magnified display area,
press the <o><p> buttons or turn the
<5> dial to specify the general focal
position, and then press the <m> button.
MF Indicator
3 Fine-tune the focus.
zz
Press the shutter button halfway to have
the camera fine-tune the focal position
(Safety MF).
• AF frame mode or size cannot be changed while focusing
manually (= 92). If you want to change the AF frame mode or
size, cancel manual focus mode first.
• Focusing is possible when using the digital zoom (= 49) or
digital tele-converter (= 92), or when using a TV as a display
(= 163), but the magnified display will not appear.
C
Y
P
O
• To focus more accurately, try attaching the camera to a tripod to stabilize it.
• To hide the magnified display area, press the <n> button and set [MFPoint Zoom] on the [4] tab to [Off] (= 38).
• To deactivate automatic focus fine-tuning when the shutter button is pressed
halfway, press the <n> button and set [Safety MF] on the [4] tab to
[Off] (= 38).
91
Shooting Range and Focusing
Still Images
Movies
Digital Tele-Converter
The focal length of the lens can be increased by approximately 1.6x or 2.0x.
This can reduce camera shake because the shutter speed is faster than it
would be if you zoomed (including using digital zoom) in to the same zoom
factor.
zz
Press the <n> button, choose
[Digital Zoom] on the [4] tab, and then
choose the desired option (= 38).
XX
The view is enlarged and the zoom factor
is displayed on the screen.
Y
P
O
• The digital tele-converter cannot be used with digital zoom
(= 49) and AF-point zoom (= 60).
• The respective focal lengths when using [1.6x] and [2.0x] are 44.8 –
716.8 mm and 56.0 – 896.0 mm (35mm film equivalent).
• The shutter speed may be equivalent when you move the zoom lever all the
way toward <i> for maximum telephoto, and when you zoom in to enlarge
the subject to the same size following step 2 on = 49.
C
Still Images
Movies
Changing the AF Frame Mode
Change the AF (auto focus) frame mode to suit the shooting conditions as
follows.
zz
Press the <n> button, choose [AF Frame] on the [4] tab, and then
choose the desired option (= 38).
92
Shooting Range and Focusing
Still Images
Movies
Center
One AF frame is displayed in the center. Effective for reliable focusing.
• A yellow AF frame is displayed with [ ] if the camera cannot
focus when you press the shutter button halfway. Note that AFpoint zooming (= 60) is not possible.
• To reduce the AF frame size, press the <n> button and set [AF Frame
Size] on the [4] tab to [Small] (= 38).
• The AF frame size is set to [Normal] when you use the digital zoom (= 49)
or digital tele-converter (= 92), and in manual focus mode (= 90).
• To compose shots so that subjects are positioned at the edge or in a corner,
first aim the camera to capture the subject in an AF frame, and then hold
the shutter button halfway down. As you continue to hold the shutter button
halfway, recompose the shot as desired, and then press the shutter button all
the way down (Focus Lock).
Face AiAF
C
Y
P
O
Still Images
Movies
• Detects people’s faces, and then sets the focus, exposure (evaluative
metering only), and white balance ([ ] only).
• After you aim the camera at the subject, a white frame is displayed
around the person’s face determined by the camera to be the main
subject, and up to two gray frames are displayed around other detected
faces.
• When the camera detects movement, frames will follow moving subjects,
within a certain range.
• After you press the shutter button halfway, up to nine green frames are
displayed around faces in focus.
93
Shooting Range and Focusing
• If faces are not detected, or when only gray frames are displayed
(without a white frame), up to nine green frames are displayed in
the areas in focus when you press the shutter button halfway.
• If faces are not detected when Servo AF (= 95) is set to [On],
the AF frame is displayed in the center of the screen when you
press the shutter button halfway.
• Examples of faces that cannot be detected:
-Subjects that are distant or extremely close
-Subjects that are dark or light
-Faces in profile, at an angle, or partly hidden
• The camera may misinterpret non-human subjects as faces.
• No AF frames are displayed if the camera cannot focus when you
press the shutter button halfway.
Y
P
O
Still Images
Choosing Subjects to Focus On (Tracking AF)
Shoot after choosing a subject to focus on as follows.
C
1 Choose [Tracking AF].
zz
Follow the steps on = 92 to choose
[Tracking AF].
XX
[ ] is displayed in the center of the screen.
2 Choose a subject to focus on.
zz
Aim the camera so that [
] is on the
desired subject, and then press the <q>
button.
XX
When the subject is detected, the camera
94
beeps and [ ] is displayed. Even if the
subject moves, the camera will continue
to track the subject within a certain range.
XX
If no subject is detected, [ ] is displayed.
zz
To cancel tracking, press the <q> button
again.
Shooting Range and Focusing
3 Shoot.
zz
Press the shutter button halfway. [
] changes
to a blue [ ], which follows the subject as
the camera continues to adjust the focus and
exposure (Servo AF) (see below).
zz
Press the shutter button all the way down
to shoot.
XX
Even after your shot, [ ] is still displayed
and the camera continues to track the subject.
• [Servo AF] (see below) is set to [On] and cannot be changed.
• Tracking may not be possible when subjects are too small or move
too rapidly, or when subject color or brightness matches that of the
background too closely.
• [AF-Point Zoom] on the [4] tab is not available.
• [e] is not available.
Y
P
O
• The camera can detect subjects even if you press the shutter button halfway
without pressing the <q> button. After your shot, [ ] is displayed in the
center of the screen.
• When shooting in [f] mode (= 90), press and hold the <q> button for at
least one second.
C
Still Images
Shooting with Servo AF
This mode helps avoid missing shots of subjects in motion, because the
camera continues to focus on the subject and adjust the exposure as long
as you press the shutter button halfway.
1 Configure the setting.
zz
Press the <n> button, choose
[Servo AF] on the [4] tab, and then
choose [On] (= 38).
95
Shooting Range and Focusing
2 Focus.
zz
The focus and exposure are maintained
where the blue AF frame is displayed
while you are pressing the shutter button
halfway.
• Focusing may not be possible in some shooting conditions.
• In low-light conditions, Servo AF may not be activated (AF frames
may not turn blue) when you press the shutter button halfway.
In this case, the focus and exposure are set according to the
specified AF frame mode.
• If adequate exposure cannot be obtained, shutter speeds and
aperture values are displayed in orange. Release the shutter
button, and then press it halfway again.
• AF lock shooting is not available.
• [AF-Point Zoom] on the [4] tab is not available.
• Not available when using the self-timer (= 50).
C
Y
P
O
Still Images
Changing the Focus Setting
You can change default camera operation of constantly focusing on
subjects it is aimed at, even when the shutter button is not pressed. Instead,
you can limit camera focusing to the moment you press the shutter button
halfway.
zz
Press the <n> button, choose
[Continuous AF] on the [4] tab, and then
choose [Off] (= 38).
96
On
Helps avoid missing sudden photo
opportunities, because the camera
constantly focuses on subjects until you
press the shutter button halfway.
Off
Conserves battery power, because the
camera does not focus constantly.
Shooting Range and Focusing
Still Images
Movies
Shooting with the AF Lock
The focus can be locked. After you lock the focus, the focal position will not
change even when you release your finger from the shutter button.
1 Lock the focus.
zz
With the shutter button pressed halfway,
press the <q> button.
XX
The focus is now locked, and [f] and
the MF indicator are displayed.
zz
To cancel AF lock, release the shutter
button, hold the shutter button halfway
down again, and press the <q> button.
2 Compose the shot and shoot.
C
Y
P
O
97
Flash
Still Images
Activating Flash
You can have the flash fire for each shot. For details on the flash range, see
“Specifications” (= 203).
1 Raise the flash.
zz
Press the <h> button.
2 Configure the setting.
zz
Press the <r> button, choose [h] (either
press the <q><r> buttons or turn the
<5> dial), and then press the <m>
button.
XX
Once the setting is complete, [h] is
displayed.
Y
P
O
• The setting screen cannot be accessed by pressing the <r>
button when the flash is lowered. Press the <h> button to raise
the flash, then configure the setting.
C
Still Images
Shooting with Slow Synchro
With this option, the flash fires to increase the brightness of the main
subject (such as people) while the camera shoots at a slow shutter speed to
increase the brightness of the background that is out of the flash range.
For details on the flash range, see “Specifications” (= 203).
1 Raise the flash.
zz
Press the <h> button.
2 Configure the setting.
zz
Press the <r> button, choose [Z] (either
press the <q><r> buttons or turn the
<5> dial), and then press the <m>
button.
XX
Once the setting is complete, [Z] is
displayed.
98
Flash
3 Shoot.
zz
Even after the flash fires, ensure that
the main subject does not move until the
shutter sound is finished playing.
• Mount the camera on a tripod or take other measures to keep it
still and prevent camera shake. Additionally, you should set [IS
Mode] to [Off] when using a tripod or other means to hold the
camera still (= 101).
• The setting screen cannot be accessed by pressing the <r>
button when the flash is lowered. Press the <h> button to raise
the flash, then configure the setting.
Still Images
Adjusting the Flash Exposure Compensation
Y
P
O
Just as with regular exposure compensation (= 81), you can adjust the
flash exposure from –2 to +2 stops, in 1/3-stop increments.
C
zz
Press the <m> button, choose [X] in
the menu, and adjust the setting by either
pressing the <q><r> buttons or turning
the <5> dial (= 37).
XX
Once the setting is complete, [X] is
displayed.
• When there is a risk of overexposure, the camera automatically adjusts the
shutter speed or aperture value during the flash shots to reduce washed-out
highlights and shoot at optimal exposure. However, you can deactivate automatic
adjustment of the shutter speed and aperture value by accessing <n>
(= 38) and setting [Safety FE] in [Flash Settings] on the [4] tab to [Off].
• You can also configure the flash exposure compensation by accessing
<n> (= 38) and choosing [Flash Exp. Comp] in [Flash Settings] on
the [4] tab.
• You can also access the [Flash Settings] <n> screen when the flash
is up by pressing the <r> button and immediately pressing the <n>
button.
99
Flash
Still Images
Shooting with the FE Lock
Just as with the AE lock (= 81), you can lock the exposure for the flash
shots.
1 Raise the flash and set it to [h]
(= 98).
2 Lock the flash exposure.
zz
Aim the camera at the subject to shoot
with the exposure locked. With the
shutter button pressed halfway, press the
<b> button.
XX
The flash fires, and when [ ] is
displayed, the flash output level is
retained.
zz
To unlock FE, release the shutter button
and press the <b> button again. In this
case, [ ] is no longer displayed.
C
Y
P
O
3 Compose the shot and shoot.
zz
After one shot, FE is unlocked and [
no longer displayed.
• FE: Flash Exposure
100
] is
Other Settings
Still Images
Changing the Compression Ratio (Image Quality)
Choose from two compression ratios, as follows: [ ] (Super Fine),
[ ] (Fine). For guidelines on how many shots at each compression ratio
can fit on a memory card, see “Specifications” (= 203).
Configure the setting.
zz
Press the <m> button, choose [
] in
the menu, and choose the desired option
(= 37).
Still Images
Y
P
O
Movies
Changing the IS Mode Settings
zz
Press the <n> button, choose [IS
C
Mode] on the [4] tab, and then press the
<q><r> buttons to choose the desired
option (= 38).
Continuous
Optimal image stabilization
for the shooting conditions is
automatically applied (Intelligent
IS) (= 47).
Shoot Only*
Image stabilization is active only at
the moment of shooting.
Off
Deactivates image stabilization.
*The setting is changed to [Continuous] for movie
recording.
• If image stabilization cannot prevent camera shake, mount the
camera on a tripod or take other measures to hold it still. In this
case, set [IS Mode] to [Off].
101
C
102
Y
P
O
5
Tv, Av, and M Mode
Y
P
O
Take smarter, more sophisticated shots
C
• Instructions in this chapter apply to the camera as set to the respective
mode.
103
Still Images
Specific Shutter Speeds (<Tv> Mode)
Set your preferred shutter speed before shooting as follows. The camera
automatically adjusts the aperture value to suit your shutter speed.
For details on available shutter speeds, see “Specifications” (= 203).
1 Enter <M> mode.
zz
Set the mode dial to <M>.
2 Set the shutter speed.
zz
Turn the <5> dial to set the shutter
speed.
Y
P
O
• With shutter speeds of 1.3 seconds or slower, there will be a delay
before you can shoot again, as images are processed to remove
noise.
• When shooting at low shutter speeds on a tripod, you should set
[IS Mode] to [Off] (= 101).
• Maximum shutter speed with the flash is 1/2000 second. If you
specify a faster speed, the camera will automatically reset the
speed to 1/2000 second before shooting.
• Orange display of aperture values when you press the shutter
button halfway indicates that the settings deviate from standard
exposure. Adjust the shutter speed until the aperture value is
displayed in white, or use safety shift (= 105).
C
• <M>: Time value
104
Still Images
Specific Aperture Values (<Av> Mode)
Set your preferred aperture value before shooting as follows. The camera
automatically adjusts the shutter speed to suit your aperture value.
For details on available aperture values, see “Specifications” (= 203).
1 Enter <B> mode.
zz
Set the mode dial to <B>.
2 Set the aperture value.
zz
Turn the <5> dial to set the aperture
value.
Y
P
O
• Orange display of shutter speeds when you press the shutter
button halfway indicates that the settings deviate from standard
exposure. Adjust the aperture value until the shutter speed is
displayed in white, or use safety shift (see below).
C
• <B>: Aperture value (size of the opening made by the iris in the lens)
• To avoid exposure problems in <M> and <B> modes, you can have the
camera automatically adjust the shutter speed or aperture value, even when
standard exposure cannot otherwise be obtained. Press the <n> button
and set [Safety Shift] on the [4] tab to [On] (= 38). However, safety shift
is disabled when the flash fires.
105
Still Images
Specific Shutter Speeds and Aperture
Values (<M> Mode)
Follow these steps before shooting to set your preferred shutter speed
and aperture value to obtain the desired exposure. For details on available
shutter speeds and aperture values, see “Specifications” (= 203).
1 Enter <D> mode.
zz
Set the mode dial to <D>.
2 Configure the setting.
zz
Press the <b> button, choose
Aperture Value
Shutter Speed
Standard Exposure
Level
Exposure Level Mark
Exposure Level Indicator
adjustment of shutter speed or aperture
value, and turn the <5> dial to specify
a value.
XX
An exposure level mark based on your
specified value is shown on the exposure
level indicator for comparison to the
standard exposure level.
XX
The exposure level mark is shown
in orange when the difference from
standard exposure exceeds 2 stops. “–2”
or “+2” is displayed in orange in the lower
right when you press the shutter button
halfway.
C
Y
P
O
• After you set the shutter speed or aperture value, the exposure
level may change if you adjust the zoom or recompose the shot.
• Screen brightness may change depending on your specified
shutter speed or aperture value. However, screen brightness
remains the same when the flash is up and the mode is set to [h].
• To have the setting you did not configure in step 2 (whether shutter
speed or aperture value) automatically adjusted to obtain standard
exposure, hold the shutter button halfway and press the <b>
button. Note that standard exposure may not be possible with
some settings.
106
Specific Shutter Speeds and Aperture Values (<M> Mode)
• <D>: Manual
• Calculation of standard exposure is based on the specified metering method
(= 82).
Still Images
Adjusting the Flash Output
Choose from the three flash levels in <D> mode.
1 Enter <D> mode.
zz
Set the mode dial to <D>.
2 Configure the setting.
zz
Press the <m> button, choose [X] in
the menu, and adjust the setting by either
pressing the <q><r> buttons or turning
the <5> dial (= 37).
XX
Once the setting is complete, [X] is
displayed.
C
Y
P
O
• You can also set the flash level by accessing <n> (= 38) and
choosing [Flash Output] in [Flash Settings] on the [4] tab.
• You can set the flash level in <M> or <B> mode by accessing <n>
(= 38), choosing [Flash Settings] on the [4] tab, and then setting [Flash
Mode] to [Manual].
• You can also access the [Flash Settings] <n> screen as follows.
-When the flash is up, press the <r> button and immediately press the
<n> button.
107
C
108
Y
P
O
6
Playback Mode
Y
P
O
Have fun reviewing your shots, and browse or edit them
in many ways
C
• To prepare the camera for these operations, press the <1> button to
enter Playback mode.
• It may not be possible to play back or edit images that were
renamed or already edited on a computer, or images from other
cameras.
109
Still Images
Movies
Viewing
After shooting images or movies, you can view them on the screen as
follows.
1 Enter Playback mode.
zz
Press the <1> button.
XX
Your last shot is displayed.
2 Browse through your images.
zz
To view the previous image, press
the <q> button or turn the <5> dial
counterclockwise. To view the next
image, press the <r> button or turn the
<5> dial clockwise.
zz
Press and hold the <q><r> buttons to
browse through images quickly. Images
appear grainy at this time.
C
Y
P
O
zz
To access Scroll Display mode, turn
the <5> dial rapidly. In this mode,
turn the <5> dial to browse through
images.
zz
To return to single-image display, press
the <m> button.
zz
To browse images grouped by shooting
date, press the <o><p> buttons in
Scroll Display mode.
zz
Movies are identified by a [
play movies, go to step 3.
110
] icon. To
Viewing
3 Play movies.
zz
To start playback, press the <m> button
to access the movie control panel, press
the <q><r> buttons to choose [ ], and
then press the <m> button again.
Volume
4 Adjust the volume.
zz
Press the <o><p> buttons to adjust the
volume.
5 Pause playback.
zz
To pause or resume playback, press the
Y
P
O
<m> button.
XX
After the movie is finished, [
displayed.
C
] is
• To switch to Shooting mode from Playback mode, press the shutter button
halfway.
• To deactivate Scroll Display, press the <n> button, choose [Scroll
Display] on the [1] tab, and then choose [Off].
• If you prefer to have the most recent shot displayed when you enter playback
mode, press the <n> button, and on the [1] tab, choose [Resume] and
then [Last shot].
• To change the transition shown between images, press the <n> button,
choose [Transition] on the [1] tab, and then press the <q><r> buttons to
choose the effect.
111
Viewing
Still Images
Movies
Switching Display Modes
Press the <l> button to view other information on the screen, or to hide
the information. For details on the information displayed, see = 190.
No Information Display
Simple
Information
Display
Detailed
Information
Display
Enables you to
check the focus
(= 113)*
*Not shown for movies.
• Switching display modes by pressing the <l> button is also possible
immediately after you shoot, while your shot is displayed. However, simple
information display is not available. To change the initial display mode, press
the <n> button and choose [Review Info] on the [4] tab (= 64).
C
Y
P
O
Still Images
Movies
Overexposure Warning (for Image Highlights)
Washed-out highlights in the image flash on the screen in detailed
information display.
Still Images
Histogram
High
Low
Dark
112
Bright
Movies
zz
The graph in detailed information display
is a histogram showing the distribution of
brightness in the image. The horizontal
axis represents the degree of brightness,
and the vertical axis, how much of the
image is at each level of brightness.
Viewing the histogram is a way to check
exposure.
Viewing
Still Images
Checking the Focus
To check the focus of your shots, you can magnify the area of the image
that was in the AF frame at the time of shooting.
1 Access Focus Check.
zz
Press the <l> button (= 112).
XX
A white frame is displayed where the AF
frame was when the focus was set.
XX
Gray frames are displayed over faces
detected later, in Playback mode.
XX
The portion of the image in the orange
frame is magnified.
2 Switch frames.
Y
P
O
zz
Move the zoom lever toward <k> once.
XX
The screen at left is displayed.
zz
To switch to a different frame when there
C
are multiple frames, press the <m>
button.
3 Zoom in or out, or view other
image areas.
zz
As you examine the focus, use the
zoom lever to zoom in or out. Press the
<o><p><q><r> buttons to adjust the
display position.
zz
Press the <n> button to restore the
original display in step 1.
113
Browsing and Filtering Images
Still Images
Movies
Navigating Through Images in an Index
By displaying multiple images in an index, you can quickly find the images
you are looking for.
1 Display images in an index.
zz
Move the zoom lever toward <g> to
display images in an index. Moving the
lever again will increase the number of
images shown.
zz
To display fewer images, move the zoom
lever toward <k>. Fewer images are
shown each time you move the lever.
2 Choose an image.
Y
P
O
zz
Turn the <5> dial to scroll through the
images.
zz
Press the <o><p><q><r> buttons to
choose an image.
XX
An orange frame is displayed around the
selected image.
zz
Press the <m> button to view the
selected image in single-image display.
C
114
Browsing and Filtering Images
Still Images
Movies
Finding Images Matching Specified Conditions
Find desired images quickly on a memory card full of images by filtering
image display according to your specified conditions. You can also protect
(= 120) or delete (= 124) these images all at once.
Favorites
Displays images tagged as favorites (= 129).
Shot Date
Displays the images shot on a specific date.
My Category
Displays the images of a specific category (= 130).
Still image/Movie
Displays only still images or movies.
1 Choose the first condition for
image display or navigation.
zz
In single-image display, press the <o>
Y
P
O
button, and then press the <o><p>
buttons to choose a display filter.
zz
When [ ] is selected, you can view
only images matching this condition by
pressing the <q><r> buttons. To perform
an action for all of these images together,
press the <m> button and go to step 3.
C
2 Choose the second condition
and check the images found.
zz
Press the <q><r> buttons to choose
another condition. Once you turn the
<5> dial, you can view the images
narrowed down by your conditions.
zz
To cancel this mode, press the <n>
button.
zz
To switch to filtered image display, press
the <m> button and go to step 3.
115
Browsing and Filtering Images
3 View the filtered images.
zz
Images matching your conditions are
displayed in yellow frames. To view
only these images, press the <q><r>
buttons, or turn the <5> dial.
zz
To exit filtered image display, press the
<o> button, and after [Image search
canceled] is displayed, press the <m>
button.
• When the camera has found no corresponding images for some
conditions, those conditions will not be available.
• To show or hide information, press the <l> button in step 2.
• Options for viewing the images found (in step 3) include “Navigating
Through Images in an Index” (= 114), “Viewing Slideshows” (= 118),
and “Magnifying Images” (= 117). You can protect, erase, or print all
images found or add them to a photobook by choosing [Select All Images
in Search] in “Protecting Images” (= 120), “Erasing All Images” (= 124),
“Adding Images to the Print List (DPOF)” (= 173), or “Adding Images to a
Photobook” (= 177).
• However, if you recategorize images (= 130) or edit them and save them
as new images (= 133 – 138), a message is displayed and filtered image
display ends.
C
116
Y
P
O
Image Viewing Options
Still Images
Magnifying Images
1 Magnify an image.
zz
Moving the zoom lever toward <k> will
zoom in and magnify the image. You
can magnify images up to about 10x by
continuing to hold the zoom lever.
zz
To zoom out, move the zoom lever
toward <g>. You can return to singleimage display by continuing to hold it.
Approximate Position of
Displayed Area
Y
P
O
2 Move the display position and
C
switch images as needed.
zz
To move the display position, press the
<o><p><q><r> buttons.
zz
To switch to other images while zoomed,
turn the <5> dial.
• You can return to single-image display from magnified display by pressing
the <n> button.
117
Image Viewing Options
Still Images
Movies
Viewing Slideshows
Automatically play back images from a memory card as follows.
1 Access the setting screen.
zz
Press the <n> button, and then
choose [Slideshow] on the [1] tab
(= 38).
2 Configure the setting.
zz
Choose a menu item to configure, and
then choose the desired option (= 38).
C
Y
P
O
3 Start automatic playback.
zz
Press the <o><p> buttons or turn the
<5> dial to choose [Start], and then
press the <m> button.
XX
The slideshow will start a few seconds
after [Loading image...] is displayed.
zz
Press the <n> button to stop the
slideshow.
• The camera’s power-saving functions (= 34) are deactivated
during slideshows.
• To pause or resume slideshows, press the <m> button.
• You can switch to other images during playback by pressing the <q><r>
buttons or turning the <5> dial. For fast-forward or fast-rewind, hold the
<q><r> buttons down.
• [Play Time] cannot be modified when [Bubble] is chosen in [Effect].
118
Image Viewing Options
Still Images
Auto Playback of Similar Images (Smart Shuffle)
Based on the current image, the camera offers four images similar to it
that you may wish to view. After you choose to view one of those images,
the camera offers four more images. This is an enjoyable way to play back
images in an unexpected order. Try this feature after you have taken many
shots, in many kinds of scenes.
1 Choose Smart Shuffle.
zz
Press the <n> button, choose
[Smart Shuffle] on the [1] tab, and then
press the <m> button (= 38).
XX
Four candidate images are displayed.
Y
P
O
2 Choose an image.
zz
Press the <o><p><q><r> buttons to
choose the image you want to view next.
XX
Your chosen image is displayed in the
center, surrounded by the next four
candidate images.
zz
For full-screen display of the center
image, press the <m> button. To restore
the original display, press the <m>
button again.
zz
Press the <n> button to restore
single-image display.
C
• Only still images shot with this camera are played back using
Smart Shuffle.
• Smart Shuffle is not available in the following cases:
-There are less than 50 shots taken with this camera
-An unsupported image is currently displayed
-Images are shown in filtered display (= 115)
119
Still Images
Movies
Protecting Images
Protect important images to prevent accidental erasure by the camera
(= 124).
Choosing a Selection Method
1 Access the setting screen.
zz
Press the <n> button and choose
[Protect] on the [1] tab (= 38).
2 Choose a selection method.
zz
Choose a menu item and a setting as
desired (= 38).
Y
P
O
zz
To return to the menu screen, press the
<n> button.
C
• Protected images on a memory card will be erased if you format
the card (= 146, 147).
• Protected images cannot be erased using the camera’s erasure function. To
erase them this way, first cancel protection.
120
Protecting Images
Choosing Images Individually
1 Choose [Select].
zz
Following step 2 on = 120, choose
[Select] and press the <m> button.
2 Choose an image.
zz
Press the <q><r> buttons or turn the
<5> dial to choose an image, and then
press the <m> button. [ ] is displayed.
zz
To cancel selection, press the <m>
button again. [ ] is no longer displayed.
zz
Repeat this process to specify other
images.
3 Protect the image.
Y
P
O
zz
Press the <n> button.
A confirmation message is displayed.
zz
Press the <q><r> buttons or turn the
C
<5> dial to choose [OK], and then press
the <m> button.
• Images will not be protected if you switch to Shooting mode or turn
the camera off before finishing the setup process in step 3.
121
Protecting Images
Selecting a Range
1 Choose [Select Range].
zz
Following step 2 on = 120, choose
[Select Range] and press the <m>
button.
2 Choose a starting image.
zz
Press the <m> button.
zz
Press the <q><r> buttons or turn the
Y
P
O
<5> dial to choose an image, and then
press the <m> button.
C
3 Choose an ending image.
zz
Press the <r> button to choose [Last
image], and then press the <m> button.
zz
Press the <q><r> buttons or turn the
<5> dial to choose an image, and then
press the <m> button.
zz
Images before the first image cannot be
selected as the last image.
122
Protecting Images
4 Protect the images.
zz
Press the <p> button to choose
[Protect], and then press the <m>
button.
• You can also choose the first or last image by turning the <5> dial when the
top screen in steps 2 and 3 is displayed.
Specifying All Images at Once
1 Choose [Select All Images].
zz
Following step 2 on = 120, choose
Y
P
O
[Select All Images] and press the <m>
button.
2 Protect the images.
C
zz
Press the <o><p> buttons or turn the
<5> dial to choose [Protect], and then
press the <m> button.
• To cancel protection for groups of images, choose [Unlock] in step 4 of
“Selecting a Range” or in step 2 of “Specifying All Images at Once”.
123
Still Images
Movies
Erasing Images
You can choose and erase unneeded images one by one. Be careful when
erasing images, because they cannot be recovered. However, protected
images (= 120) cannot be erased.
1 Choose an image to erase.
zz
Press the <q><r> buttons or turn the
<5> dial to choose an image.
2 Erase the image.
zz
Press the <a> button.
zz
After [Erase?] is displayed, press the
<q><r> buttons to choose [Erase], and
then press the <m> button.
XX
The current image is now erased.
zz
To cancel erasure, press the <q><r>
buttons or turn the <5> dial to choose
[Cancel], and then press the <m>
button.
C
Erasing All Images
Y
P
O
You can erase all images at once. Be careful when erasing images,
because they cannot be recovered. However, protected images (= 120)
cannot be erased.
Choosing a Selection Method
1 Access the setting screen.
zz
Press the <n> button, and then
choose [Erase] on the [1] tab (= 38).
124
Erasing Images
2 Choose a selection method.
zz
Choose a menu item and a setting as
desired (= 38).
zz
To return to the menu screen, press the
<n> button.
Choosing Images Individually
1 Choose [Select].
zz
Following step 2 above, choose [Select]
and press the <m> button.
2 Choose an image.
zz
Once you follow step 2 on = 121 to
Y
P
O
choose an image, [
] is displayed.
zz
To cancel selection, press the <m>
button again. [
] is no longer displayed.
zz
Repeat this process to specify other
C
images.
3 Erase the image.
zz
Press the <n> button. A
confirmation message is displayed.
zz
Press the <q><r> buttons or turn the
<5> dial to choose [OK], and then press
the <m> button.
Selecting a Range
1 Choose [Select Range].
zz
Following step 2 in “Choosing a Selection
Method” (see above), choose [Select
Range] and press the <m> button.
125
Erasing Images
2 Choose images.
zz
Follow steps 2 – 3 on = 122 to specify
images.
3 Erase the images.
zz
Press the <p> button to choose [Erase],
and then press the <m> button.
Specifying All Images at Once
1 Choose [Select All Images].
zz
Following step 2 in “Choosing a Selection
Y
P
O
Method” (= 125), choose [Select All
Images] and press the <m> button.
2 Erase the images.
C
zz
Press the <q><r> buttons or turn the
<5> dial to choose [OK], and then press
the <m> button.
126
Still Images
Movies
Rotating Images
Change the orientation of images and save them as follows.
1 Choose [Rotate].
zz
Press the <n> button and choose
[Rotate] on the [1] tab (= 38).
2 Rotate the image.
zz
Press the <q><r> buttons or turn the
<5> dial to choose an image.
zz
The image is rotated 90° each time you
press the <m> button.
Y
P
O
zz
To return to the menu screen, press the
<n> button.
• Movies with an image quality of [ ] cannot be rotated.
• Rotation is not possible when [Auto Rotate] is set to [Off]
(= 128).
C
127
Rotating Images
Deactivating Auto Rotation
Follow these steps to deactivate automatic rotation by the camera, which
rotates images shot in vertical orientation so they are displayed vertically on
the camera.
zz
Press the <n> button, choose [Auto
Rotate] on the [1] tab, and then choose
[Off] (= 38).
• Images cannot be rotated (= 127) when you set [Auto Rotate] to
[Off]. Additionally, images already rotated will be displayed in the
original orientation.
• In Smart Shuffle (= 119) mode, even if [Auto Rotate] is set to
[Off], images shot vertically will be displayed vertically, and rotated
images will be displayed in the rotated orientation.
C
128
Y
P
O
Image Categories
You can tag images as favorites or assign them to My Category (= 130)
groups. By choosing a category in filtered playback, you can restrict the
following operations to all of those images.
• Viewing (= 110), Viewing Slideshows (= 118), Protecting Images
(= 120), Erasing Images (= 124), Adding Images to the Print List
(DPOF) (= 173), Adding Images to a Photobook (= 177)
Still Images
Movies
Tagging Images as Favorites
1 Choose [Favorites].
zz
Press the <n> button and choose
[Favorites] on the [1] tab (= 38).
Y
P
O
2 Choose an image.
zz
Press the <q><r> buttons or turn the
<5> dial to choose an image, and then
press the <m> button. [ ] is displayed.
zz
To untag the image, press the <m>
button again. [ ] is no longer displayed.
zz
Repeat this process to choose additional
images.
C
3 Finish the setup process.
zz
Press the <n> button. A
confirmation message is displayed.
zz
Press the <q><r> buttons or turn the
<5> dial to choose [OK], and then press
the <m> button.
• Images will not be tagged as favorites if you switch to Shooting
mode or turn the camera off before finishing the setup process in
step 3.
129
Image Categories
• Favorite images will have a three-star rating (
) when
transferred to computers running Windows 7 or Windows Vista. (Does not
apply to movies.)
Still Images
Movies
Organizing Images by Category (My Category)
You can organize images into categories. Note that images are
automatically categorized at the time of shooting, according to shooting
conditions.
: Images with detected faces, or images shot in [I] mode.
: Images detected as [ ], [ ], or [ ] in <A> mode.
: Images shot in [P] or [t] mode.
Choosing a Selection Method
1 Access the setting screen.
Y
P
O
zz
Press the <n> button, and then
choose [My Category] on the [1] tab
(= 38).
C
2 Choose a selection method.
zz
Choose a menu item and a setting as
desired (= 38).
zz
To return to the menu screen, press the
<n> button.
130
Image Categories
Choosing Images Individually
1 Choose [Select].
zz
Following step 2 on = 130, choose
[Select] and press the <m> button.
2 Choose an image.
zz
Press the <q><r> buttons or turn the
<5> dial to choose an image.
3 Choose a category.
zz
Press the <o><p> buttons to choose
a category and then press the <m>
button. [ ] is displayed.
zz
To cancel selection, press the <m>
button again. [ ] is no longer displayed.
zz
Repeat this process to choose additional
images.
Y
P
O
4 Finish the setup process.
C
zz
Press the <n> button. A
confirmation message is displayed. Press
the <q><r> buttons or turn the <5>
dial to choose [OK], and then press the
<m> button.
• Images will not be assigned to a category if you switch to Shooting
mode or turn the camera off before finishing the setup process in
step 4.
131
Image Categories
Selecting a Range
1 Choose [Select Range].
zz
Following step 2 on = 130, choose
[Select Range] and press the <m>
button.
2 Choose images.
zz
Follow steps 2 – 3 on = 122 to specify
images.
3 Choose a category.
zz
Press the <p> button to choose the type
of image, and then press the <q><r>
buttons or turn the <5> dial to choose
a category.
Y
P
O
4 Finish the setup process.
C
zz
Press the <p> button to choose [Select],
and then press the <m> button.
• You can clear the selection of all images in the [Select Range] category by
choosing [Deselect] in step 4.
132
Still Images
Movies
Editing Still Images
• Image editing (= 133 – 138) is only available when the memory
card has sufficient free space.
Still Images
Resizing Images
Save a copy of images at a lower resolution.
1 Choose [Resize].
zz
Press the <n> button and choose
[Resize] on the [1] tab (= 38).
Y
P
O
2 Choose an image.
zz
Press the <q><r> buttons or turn the
C
<5> dial to choose an image, and then
press the <m> button.
3 Choose an image size.
zz
Press the <q><r> buttons or turn the
<5> dial to choose the size, and then
press the <m> button.
XX
[Save new image?] is displayed.
4 Save the new image.
zz
Press the <q><r> buttons or turn the
<5> dial to choose [OK], and then press
the <m> button.
XX
The image is now saved as a new file.
133
Editing Still Images
5 Review the new image.
zz
Press the <n> button. [Display new
image?] is displayed.
zz
Press the <q><r> buttons or turn the
<5> dial to choose [Yes], and then
press the <m> button.
XX
The saved image is now displayed.
• Editing is not possible for images saved as [
] in step 3.
• Images cannot be resized to a higher resolution.
Cropping
Y
P
O
Still Images
You can specify a portion of an image to save as a separate image file.
C
1 Choose [Cropping].
zz
Press the <n> button, and then
choose [Cropping] on the [1] tab
(= 38).
2 Choose an image.
zz
Press the <q><r> buttons or turn the
<5> dial to choose an image, and then
press the <m> button.
134
Editing Still Images
3 Adjust the cropping area.
Cropping Area
XX
A frame is displayed around the portion of
the image to be cropped.
XX
The original image is shown in the upper
Preview of Image After Cropping
Resolution After Cropping
left, and a preview of the image as
cropped is shown in the lower right.
zz
To resize the frame, move the zoom
lever.
zz
To move the frame, press the
<o><p><q><r> buttons.
zz
To change the frame orientation, press
the <l> button.
zz
Faces detected in the image are
enclosed in gray frames in the upper-left
image. To crop the image based on this
frame, turn the <5> dial to switch to the
other frame.
zz
Press the <m> button.
C
Y
P
O
4 Save as a new image and
review.
zz
Follow steps 4 – 5 on = 133 – 134.
• Editing is not possible for images shot at a resolution of [
(= 55) or resized to [ ] (= 133).
]
• Images supported for cropping will have the same aspect ratio after
cropping.
• Cropped images will have a smaller resolution than uncropped images.
135
Editing Still Images
Still Images
Changing Image Color Tones (My Colors)
You can adjust image colors and then save the edited image as a separate
file. For details on each option, see = 86.
1 Choose [My Colors].
zz
Press the <n> button, and then
choose [My Colors] on the [1] tab
(= 38).
2 Choose an image.
zz
Press the <q><r> buttons or turn the
Y
P
O
<5> dial to choose an image, and then
press the <m> button.
3 Choose an option.
C
zz
Press the <q><r> buttons or turn the
<5> dial to choose an option, and then
press the <m> button.
4 Save as a new image and
review.
zz
Follow steps 4 – 5 on = 133 – 134.
• Image quality of pictures you repeatedly edit this way will be a little
lower each time, and you may not be able to obtain the desired
color.
• The color of images edited using this function may vary slightly from the
color of images shot using My Colors (= 86).
136
Editing Still Images
Still Images
Correcting Image Brightness (i-Contrast)
Excessively dark image areas (such as faces or backgrounds) can be
detected and automatically adjusted to the optimal brightness. Insufficient
overall image contrast is also automatically corrected, to make subjects
stand out better. Choose from four correction levels, and then save the
image as a separate file.
1 Choose [i-Contrast].
zz
Press the <n> button, and then
choose [i-Contrast] on the [1] tab
(= 38).
Y
P
O
2 Choose an image.
zz
Press the <q><r> buttons or turn the
C
<5> dial to choose an image, and then
press the <m> button.
3 Choose an option.
zz
Press the <q><r> buttons or turn the
<5> dial to choose an option, and then
press the <m> button.
4 Save as a new image and
review.
zz
Follow steps 4 – 5 on = 133 – 134.
• For some images, correction may be inaccurate or may cause
images to appear grainy.
• Images may look grainy after repeated editing using this function.
• If [Auto] does not produce the expected results, try correcting images using
[Low], [Medium], or [High].
137
Editing Still Images
Still Images
Correcting Red-Eye
Automatically corrects images affected by red-eye. You can save the
corrected image as a separate file.
1 Choose [Red-Eye Correction].
zz
Press the <n> button, and then
choose [Red-Eye Correction] on the [1]
tab (= 38).
2 Choose an image.
zz
Press the <q><r> buttons or turn the
Y
P
O
<5> dial to choose an image.
3 Correct the image.
zz
Press the <m> button.
C
XX
Red-eye detected by the camera is now
corrected, and frames are displayed
around corrected image areas.
zz
Enlarge or reduce images as needed.
Follow the steps in = 117.
4 Save as a new image and review.
zz
Press the <o><p><q><r> buttons or
turn the <5> dial to choose [New File],
and then press the <m> button.
XX
The image is now saved as a new file.
zz
Follow step 5 on = 134.
• Some images may not be corrected accurately.
• To overwrite the original image with the corrected image, choose
[Overwrite] in step 4. In this case, the original image will be erased.
• Protected images cannot be overwritten.
138
Movies
Editing Movies
You can cut movies to remove unneeded portions at the beginning or end.
1 Choose [*].
zz
Following steps 1 – 5 on = 110 – 111,
choose [*] and press the <m> button.
XX
The movie editing panel and editing bar
are now displayed.
Movie Editing Panel
2 Specify portions to cut.
zz
Press the <o><p> buttons to choose [
] or [
].
zz
To view the portions you can cut
Movie Editing Bar
(identified by [ ] on the screen), press
the <q><r> buttons or turn the <5>
dial to move [ ]. Cut the beginning of the
movie (from [ ]) by choosing [ ], and
cut the end of the movie by choosing [ ].
zz
Even if you move [ ] to a position other
than a [ ] mark, choosing [ ] will only
cut the portion from the nearest [ ] to
the left, and choosing [ ] will cut the
portion from the nearest [ ] to the right.
C
Y
P
O
3 Review the edited movie.
zz
Press the <o><p> buttons to choose [ ], and then press the <m> button.
The edited movie is now played.
zz
To edit the movie again, repeat step 2.
zz
To cancel editing, press the <o><p>
buttons to choose [ ]. Press the <m>
button, choose [OK] (either press the
<q><r> buttons or turn the <5> dial),
and then press the <m> button again.
139
Editing Movies
4 Save the edited movie.
zz
Press the <o><p> buttons to choose [
], and then press the <m> button.
zz
Press the <o><p><q><r> buttons or
turn the <5> dial to choose [New File],
and then press the <m> button.
XX
The movie is now saved as a new file.
• To overwrite the original movie with the cut one, choose
[Overwrite] in step 4. In this case, the original movie will be erased.
• [Overwrite] is only available when memory cards lack sufficient
free space.
• Movies may not be saved if the batteries run out while saving is in
progress.
• When editing movies, you should use batteries with sufficient
charge or fully charged NiMH AA batteries (= 157), or an AC
adapter kit and DC coupler (= 157, both sold separately).
C
140
Y
P
O
7
Setting Menu
Y
P
O
Customize or adjust basic camera functions for greater
convenience
C
141
Adjusting Basic Camera Functions
Functions can be configured on the [3] tab. Customize commonly used
functions as desired, for greater convenience (= 38).
Silencing Camera Operations
Silence camera sounds and movies as follows.
zz
Choose [Mute], and then choose [On].
• Operation can also be silenced by holding down the <l> button as you
turn the camera on.
• Sound is not played during movies if you mute camera sounds (= 110). To
restore sound during movies, press the <o> button. Adjust volume with the
<o><p> buttons, as needed.
• Sound settings cannot be changed in [ ] mode (= 76).
C
Y
P
O
Adjusting the Volume
Adjust the volume of individual camera sounds as follows.
zz
Choose [Volume], and then press the
<m> button.
zz
Choose an item, and then press the
<q><r> buttons to adjust the volume.
142
Adjusting Basic Camera Functions
Customizing Sounds
Customize camera operating sounds as follows.
zz
Choose [Sound Options], and then press
the <m> button.
zz
Choose an item, and then press the
<q><r> buttons to choose an option.
1
Preset sounds
(cannot be modified)
2
Preset sounds
Can be changed by using the included
software.
• Sound settings cannot be changed in [
] mode (= 76).
Y
P
O
Hiding Hints and Tips
Hints and tips are normally shown when you choose FUNC. menu
(= 37) or Menu (= 38) items. If you prefer, you can deactivate this
information.
C
zz
Choose [Hints & Tips], and then choose
[Off].
143
Adjusting Basic Camera Functions
Screen Brightness
Adjust screen brightness as follows.
zz
Choose [LCD Brightness], and then
press the <q><r> buttons to adjust the
brightness.
• For maximum brightness, press and hold the <l> button for at least
one second when the shooting screen is displayed or when in single-image
display. (This will override the [LCD Brightness] setting on the [3] tab.) To
restore the original brightness, press and hold the <l> button again for
at least one second or restart the camera.
Start-up Screen
C
Y
P
O
Customize the start-up screen shown after you turn the camera on as
follows.
zz
Choose [Start-up Image], and then press
the <m> button.
zz
Press the <q><r> buttons or turn the
<5> dial to choose an option.
No start-up image
144
1
Preset image
(cannot be modified)
2
Preset image
Assign a desired shot, or use the
included software to change the image.
Adjusting Basic Camera Functions
Customizing the Start-up Screen
1 Access the [Start-up Image]
screen in Playback mode.
zz
Press the <1> button.
zz
Following the previous procedure, choose
[2] and press the <m> button.
2 Choose one of your shots.
zz
Choose an image and press the <m>
button. After [Register?] is displayed,
choose [OK] (either press the <q><r>
buttons or turn the <5> dial), and then
press the <m> button.
Y
P
O
• The previous start-up setting is overwritten when you assign a new
start-up image.
C
• You can assign the operating sounds and start-up image for your camera
from the included software. Refer to the Software Guide (= 25) for details.
145
Adjusting Basic Camera Functions
Formatting Memory Cards
Before using a new memory card or a card formatted in another device, you
should format the card with this camera.
Formatting erases all data on a memory card. Before formatting, copy
images on the memory card to a computer, or take other steps to back them
up.
An Eye-Fi card (= 179) contains software on the card itself. Before
formatting an Eye-Fi card, install the software on a computer.
1 Access the [Format] screen.
zz
Choose [Format], and then press the
<m> button.
Y
P
O
2 Choose [OK].
zz
Press the <o><p> buttons to choose
C
[Cancel], choose [OK] (either press the
<q><r> buttons or turn the <5> dial),
and then press the <m> button.
3 Format the memory card.
zz
To begin the formatting process, press
the <o><p> buttons or turn the <5>
dial to choose [OK], and then press the
<m> button.
zz
When formatting is finished, [Memory
card formatting complete] is displayed.
Press the <m> button.
• Formatting or erasing data on a memory card only changes file
management information on the card and does not erase the data
completely. When transferring or disposing of memory cards, take
steps to protect personal information if necessary, as by physically
destroying cards.
146
Adjusting Basic Camera Functions
• The total card capacity indicated on the formatting screen may be less than
the advertised capacity.
Low-Level Formatting
Perform low-level formatting in these cases: [Memory card error] is
displayed, the camera is not working correctly, card image reading/writing is
slower, continuous shooting is slower, or movie recording suddenly stops.
Low-level formatting erases all data on a memory card. Before low-level
formatting, copy images on the memory card to a computer, or take other
steps to back them up.
Perform low-level formatting.
zz
On the screen in step 2 on = 146,
press the <o><p> buttons or turn the
<5> dial to choose [Low Level Format],
and then select this option (mark with a [ ]) by pressing the <q><r> buttons.
zz
Follow steps 2 – 3 on = 146 to continue
with the formatting process.
C
Y
P
O
• Low-level formatting takes longer than “Formatting Memory Cards”
(= 146), because data is erased from all storage regions of the memory
card.
• You can cancel low-level formatting in progress by choosing [Stop]. In this
case, all data will be erased, but the memory card can be used normally.
147
Adjusting Basic Camera Functions
File Numbering
Your shots are automatically numbered in sequential order (0001 – 9999)
and saved in folders that store up to 2,000 images each. You can change
how the camera assigns file numbers.
zz
Choose [File Numbering], and then
choose an option.
Continuous
Images are numbered
consecutively (until the 9999th
shot is taken/saved) even if
you switch memory cards.
Auto Reset
Image numbering is reset to
0001 if you switch memory
cards, or when a new folder is
created.
Y
P
O
• Regardless of the option selected in this setting, shots may be numbered
consecutively after the last number of existing images on newly inserted
memory cards. To start saving shots from 0001, use an empty (or formatted
(= 146)) memory card.
• Refer to the Software Guide (= 25) for information on the card folder
structure and image formats.
C
Date-Based Image Storage
Instead of saving images in folders created each month, you can have the
camera create folders each day you shoot to store shots taken that day.
zz
Choose [Create Folder], and then choose
[Daily].
XX
Images will now be saved in folders
created on the shooting date.
148
Adjusting Basic Camera Functions
Lens Retraction Timing
The lens is normally retracted for safety about one minute after you press
the <1> button in Shooting mode (= 34). To have the lens retracted
immediately after you press the <1> button, set the retraction timing to [0 sec.].
zz
Choose [Lens Retract], and then choose
[0 sec.].
Power-Saving Adjustment
Y
P
O
Adjust the timing of automatic camera and screen deactivation (Auto Power
Down and Display Off, respectively) as needed (= 34).
1 Access the [Power Saving]
C
screen.
zz
Choose [Power Saving], and then press
the <m> button.
2 Configure the settings.
zz
After choosing an item, press the
<q><r> buttons to adjust it as needed.
• To conserve battery power, you should normally choose [On] for
[Auto Power Down] and [1 min.] or less for [Display Off].
• The [Display Off] setting is applied even if you set [Auto Power Down] to
[Off].
149
Adjusting Basic Camera Functions
World Clock
To ensure that your shots will have the correct local date and time when you
travel abroad, simply register the destination in advance and switch to that
time zone. This convenient feature eliminates the need to change the Date/
Time setting manually.
Before using the world clock, be sure to set the date and time in “Setting the
Date and Time” (= 17) and your home time zone.
1 Specify your destination.
zz
Choose [Time Zone], and then press the
<m> button.
zz
Press the <o><p> buttons or turn the
<5> dial to choose [ World], and then
press the <m> button.
zz
Press the <q><r> buttons or turn the
<5> dial to choose the destination.
zz
To set daylight saving time (1 hour
ahead), press the <o><p> buttons to
choose [ ].
zz
Press the <m> button.
C
Y
P
O
2 Switch to the destination time
zone.
zz
Press the <o><p> buttons or turn the
<5> dial to choose [ World], and then
press the <n> button.
XX
[ ] is now shown on the shooting screen
(“On-Screen Information” (= 188)).
• Adjusting the date or time while in [ ] mode (= 17) will automatically
Home] time and date.
update your [
150
Adjusting Basic Camera Functions
Changing the Date and Time
Adjust the date and time as follows.
1 Access the [Date/Time] screen.
zz
Choose [Date/Time], and then press the
<m> button.
2 Configure the setting.
zz
Press the <q><r> buttons to choose an
item, and then adjust the setting, either
by pressing the <o><p> buttons or
turning the <5> dial.
Metric/Non-Metric Display
Change the unit of measurement shown in the MF indicator (= 91) and
zoom bar (= 42) from m/cm to ft/in as needed.
Y
P
O
zz
Choose [Units], and then choose [ft/in].
C
Checking Certification Logos
Some logos for certification requirements met by the camera can be viewed
on the screen. Other certification logos are printed in this guide, on the
camera packaging, or on the camera body.
zz
Choose [Certification Logo Display], and
then press the <m> button.
151
Adjusting Basic Camera Functions
Display Language
Change the display language as needed.
1 Access the [Language] screen.
zz
Choose [Language
the <m> button.
], and then press
2 Configure the setting.
zz
Press the <o><p><q><r> buttons or
turn the <5> dial to choose a language,
and then press the <m> button.
• You can also access the [Language] screen in Playback mode by pressing
and holding the <m> button and immediately pressing the <n> button.
Y
P
O
Adjusting Other Settings
The following settings can also be adjusted on the [3] tab.
• [Video System] (= 163)
• [Ctrl via HDMI] (= 161)
• [Eye-Fi Settings] (= 179)
C
Restoring Defaults
If you accidentally change a setting, you can restore default camera
settings.
1 Access the [Reset All] screen.
zz
Choose [Reset All], and then press the
<m> button.
2 Restore default settings.
zz
Press the <q><r> buttons or turn the
<5> dial to choose [OK], and then press
the <m> button.
XX
Default settings are now restored.
152
Adjusting Basic Camera Functions
• The following functions are not restored to default settings.
] (= 19), -[3] tab settings [Date/Time] (= 17), [Language
[Time Zone] (= 150), [Video System] (= 163), and the image assigned
to [Start-up Image] (= 144)
-Custom white balance data you have recorded (= 85)
-Shooting mode chosen in <K> (= 67) or < > (= 71) mode
-The movie mode (= 77)
C
Y
P
O
153
C
154
Y
P
O
8
Accessories
Y
P
O
Use included accessories effectively and enjoy the
camera in more ways with optional Canon accessories
and other compatible accessories sold separately
C
155
Replacing the Date/Time Battery
The date/time battery (back-up battery) will last about three years. If the
Date/Time screen is displayed every time you turn the camera on, replace
the date/time battery with a new one (CR1220).
1 Make sure the camera is off.
2 Remove the date/time battery
holder.
3 Replace the battery.
zz
Insert the battery with the (+) and (–)
sides facing the correct way.
Y
P
O
4 Insert the battery holder.
5 Insert the battery and close the
C
cover.
6 Turn the camera on and set the
date and time (= 17).
156
Optional Accessories
The following camera accessories are sold separately. Note that availability
varies by area, and some accessories may no longer be available.
Power Supplies
AC Adapter Kit ACK800
zz
For powering the camera using
household power. Recommended when
using the camera over extended periods,
or when connecting the camera to a
printer or computer. Cannot be used to
charge the camera batteries. DC Coupler
DR-DC10 is required to connect the
adapter to the camera.
DC Coupler DR-DC10
Y
P
O
zz
Used with the AC adapter kit
C
Battery and Charger Kit CBK4-300
zz
Includes four rechargeable AA NiMH
batteries (NB-3AH) and a battery charger
(CB-5AH). Recommended when using
the camera over extended periods.
• A set of four rechargeable AA NiMH batteries (NiMH Battery NB4-300) is also
available without the charger.
• Battery and Charger Kit CBK4-200 can also be used.
• The battery and charger kit and AC adapter kit can be used in
areas with 100 – 240 V AC power (50/60 Hz).
• For power outlets in a different format, use a commercially
available adapter for the plug. Never use an electrical transformer
designed for traveling, which may damage the battery.
157
Optional Accessories
Flash Unit
High-Power Flash HF-DC2
zz
External flash for illuminating subjects
that are out of range of the built-in flash.
High-Power Flash HF-DC1 can also be
used.
Other Accessories
Stereo AV Cable AVC-DC400ST
zz
Connect the camera to a TV to enjoy
playback on the larger TV screen.
Y
P
O
HDMI Cable HTC-100
zz
For connecting the camera to an HDMI
input of a high-definition TV.
Printers
C
Canon PictBridge-Compatible
Printers
zz
Printing images without a computer is
possible by connecting the camera to a
Canon PictBridge-compatible printer. For
details, visit your nearest Canon dealer.
158
Still Images
Movies
Using Optional Accessories
Still Images
Movies
Playback on a TV
By connecting the camera to a TV, you can view your shots on the larger
screen of the TV.
For details on connection or how to switch inputs, refer to the TV manual.
• Some information may not be displayed on the TV (= 190).
Still Images
Movies
Playback on a High-Definition TV
Connecting the camera to an HDTV with the HDMI Cable HTC-100 (sold
separately) enables you to view your shots on the larger screen of the TV.
Movies shot at a resolution of [ ] can be viewed in high-definition.
Y
P
O
1 Make sure the camera and TV
are off.
2 Connect the camera to the TV.
C
zz
On the TV, insert the cable plug fully into
the HDMI input as shown.
zz
On the camera, open the terminal cover
and insert the cable plug fully into the
camera terminal.
159
Using Optional Accessories
3 Turn the TV on and switch to
video input.
zz
Switch the TV input to the video input you
connected the cable to in step 2.
4 Turn the camera on.
zz
Press the <1> button to turn the camera
on.
XX
Images from the camera are now
displayed on the TV. (Nothing is
displayed on the camera screen.)
zz
When finished, turn off the camera and
TV before disconnecting the cable.
• Camera operating sounds are not played while the camera is connected to
an HDTV.
C
160
Y
P
O
Using Optional Accessories
Still Images
Movies
Controlling the Camera with a TV Remote
Connecting the camera to an HDMI CEC-compatible TV enables playback
(including slideshow playback) using the TV remote control.
In this case, you will need to adjust some TV settings. For details, refer to
the TV user manual.
1 Configure the setting.
zz
Press the <n> button, choose
[Ctrl via HDMI] on the [3] tab, and then
choose [Enable] (= 38).
2 Connect the camera to the TV.
Y
P
O
zz
Follow steps 1 – 2 on = 159 to connect
the camera to the TV.
3 Display images.
C
zz
Turn on the TV. On the camera, press the
<1> button.
XX
Images from the camera are now
displayed on the TV. (Nothing is
displayed on the camera screen.)
4 Control the camera with the TV
remote.
zz
Press the <q><r> buttons on the remote
to browse images.
zz
To display the camera control panel,
press the OK/Select button. Select
control panel items by pressing the
<q><r> buttons to choose an item, and
then pressing the OK/Select button again.
161
Using Optional Accessories
Camera Control Panel Options Shown on the TV
.
Return
Closes the menu.
Play Movie
Starts movie playback. (Only displayed when a movie
is selected.)
Slideshow
Starts slideshow playback. To switch images during
playback, press the <q><r> buttons on the remote
control.
Index Playback
l Change Display
Displays multiple images in an index.
Switches display modes (= 36).
• Pressing the <n> button on the camera will switch control to the
camera itself, which will prevent remote control until you return to singleimage display.
• Moving the zoom lever on the camera will switch control to the camera itself,
which will prevent remote control until you return to single-image display.
• The camera may not always respond correctly even if the remote is for an
HDMI CEC-compatible TV.
C
Y
P
O
Still Images
Movies
Playback on a Standard-Definition TV
Connecting the camera to a TV with the Stereo AV Cable AVC-DC400ST
(sold separately) enables you to view your shots on the larger screen of the
TV as you control the camera.
1 Make sure the camera and TV
are off.
Yellow
Yellow
White Red
zz
On the TV, insert the cable plugs fully into
the video inputs as shown.
Red
White
162
2 Connect the camera to the TV.
Using Optional Accessories
zz
On the camera, open the terminal cover
and insert the cable plug fully into the
camera terminal.
3 Display images.
zz
Follow steps 3 – 4 on = 160 to display
images.
• Correct display is not possible unless the camera video output
format (NTSC or PAL) matches the TV format. To change the
video output format, press the <n> button and choose [Video
System] on the [3] tab.
Y
P
O
• When the camera and TV are connected, you can also shoot while
previewing shots on the larger screen of the TV. To shoot, follow the same
steps as when using the camera screen. However, AF-Point Zoom (= 60)
and MF-Point Zoom (= 90) are not available.
C
163
Using Optional Accessories
Still Images
Movies
Powering the Camera with Household Power
Powering the camera with AC Adapter Kit ACK800 and DC Coupler DRDC10 (both sold separately) eliminates the need to monitor the remaining
battery level.
1 Make sure the camera is off.
2 Open the cover.
zz
Follow step 2 on = 15 to open the
memory card/battery cover.
zz
Open the coupler cable port as shown.
Coupler Cable Port
Y
P
O
3 Insert the coupler.
zz
Insert the coupler as shown.
C
zz
Make sure the coupler cable passes
through the port.
4 Close the cover.
zz
Lower the cover ( ) and hold it down as
you slide it, until it clicks into the closed
position ( ).
164
Using Optional Accessories
5 Connect the power cord.
zz
Insert the adapter plug into the end of the
coupler cable.
zz
Insert one end of the power cord into the
compact power adapter, and then plug
the other end into a power outlet.
zz
Turn the camera on and use it as desired.
zz
When finished, turn the camera off and
unplug the power cord from the outlet.
• Do not disconnect the adapter or unplug the power cord while
the camera is still on. This may erase your shots or damage the
camera.
• Do not attach the adapter or adapter cord to other objects. Doing
so could result in malfunction or damage to the product.
C
Y
P
O
165
Still Images
Movies
Printing Images
Your shots can easily be printed by connecting the camera to a printer. On
the camera, you can specify images to set up batch printing, prepare orders
for photo development services, and prepare orders or print images for
photobooks.
A Canon SELPHY CP series compact photo printer is used here for the
sake of illustration. Screens displayed and available functions vary by
printer. Also refer to the printer manual for additional information.
Still Images
Easy Print
Easily print your shots by connecting the camera to a PictBridge-compatible
printer (sold separately) with the included interface cable (= 2).
1 Make sure the camera and
printer are off.
Y
P
O
2 Connect the camera to the
printer.
zz
Open the cover. Holding the smaller
C
cable plug in the orientation shown, insert
the plug fully into the camera terminal.
zz
Connect the larger cable plug to the
printer. For other connection details, refer
to the printer manual.
3 Turn the printer on.
4 Turn the camera on.
zz
Press the <1> button to turn the camera
on.
166
Printing Images
XX
[
] is displayed.
5 Choose an image.
zz
Press the <q><r> buttons or turn the
<5> dial to choose an image.
6 Access the printing screen.
zz
Press the <m> button.
7 Print the image.
Y
P
O
zz
Press the <o><p> buttons or turn the
<5> dial to choose [Print], and then
press the <m> button.
XX
Printing now begins.
zz
To print other images, repeat steps 5 – 6
after printing is finished.
zz
When you are finished printing, turn the
camera and printer off and disconnect the
interface cable.
C
• For Canon PictBridge-compatible printers (sold separately), see = 158.
167
Printing Images
Still Images
Configuring Print Settings
1 Access the printing screen.
zz
Follow steps 1 – 6 on = 166 – 167 to
access the screen at left.
2 Configure the settings.
zz
Press the <o><p> buttons or turn
the <5> dial to choose an item, and
then choose an option by pressing the
<q><r> buttons.
Default
Date
File No.
Both
Off
Default
Y
P
O
Matches current printer settings.
Prints images with the date added.
C
Prints images with the file number added.
Prints images with both the date and file number added.
–
Matches current printer settings.
Off
–
On
Uses information from the time of shooting to print under
optimal settings.
Red-Eye 1
Corrects red-eye.
No. of Copies Choose the number of copies to print.
Cropping
–
Specify a desired image area to print (= 169).
Paper
Settings
–
Specify the paper size, layout, and other details
(= 170).
168
Printing Images
Still Images
Cropping Images Before Printing (Cropping)
By cropping images before printing, you can print a desired image area
instead of the entire image.
1 Choose [Cropping].
zz
After following step 1 on = 168 to
access the printing screen, choose
[Cropping] and press the <m> button.
XX
A cropping frame is now displayed,
indicating the image area to print.
2 Adjust the cropping frame as
needed.
Y
P
O
zz
To resize the frame, move the zoom lever
or turn the <5> dial.
zz
To move the frame, press the
<o><p><q><r> buttons.
zz
To rotate the frame, press the <l>
button.
zz
When finished, press the <m> button.
C
3 Print the image.
zz
Follow step 7 on = 167 to print.
• Cropping may not be possible at small image sizes, or at some
aspect ratios.
• Dates may not be printed correctly if you crop images shot with
[Date Stamp] selected.
169
Printing Images
Still Images
Choosing Paper Size and Layout Before Printing
1 Choose [Paper Settings].
zz
After following step 1 on = 168 to
access the printing screen, choose
[Paper Settings] and press the <m>
button.
2 Choose a paper size.
zz
Press the <o><p> buttons or turn the
<5> dial to choose an option, and then
press the <m> button.
Y
P
O
3 Choose a type of paper.
C
zz
Press the <o><p> buttons or turn the
<5> dial to choose an option, and then
press the <m> button.
4 Choose a layout.
zz
Press the <o><p> buttons or turn the
<5> dial to choose an option.
zz
When choosing [N-up], press the
<q><r> buttons to specify the number of
images per sheet.
zz
Press the <m> button.
5 Print the image.
170
Printing Images
Available Layout Options
Default
Matches current printer settings.
Bordered
Prints with blank space around the image.
Borderless Borderless, edge-to-edge printing.
N-up
Choose how many images to print per sheet.
ID Photo
Prints images for identification purposes.
Only available for images with a resolution of L and an aspect ratio of 4:3.
Fixed Size
Choose the print size.
Choose from 3.5 x 5 in., postcard, or wide-format prints.
Still Images
Printing ID Photos
1 Choose [ID Photo].
Y
P
O
zz
Following steps 1 – 4 on = 170, choose
[ID Photo] and press the <m> button.
2 Choose the long and short side
C
length.
zz
Press the <o><p> buttons or turn the
<5> dial to choose an item. Choose the
length by pressing the <q><r> buttons,
and then press the <m> button.
3 Choose the printing area.
zz
Follow step 2 on = 169 to choose the
printing area.
4 Print the image.
171
Printing Images
Movies
Printing Movie Scenes
1 Access the printing screen.
zz
Follow steps 1 – 5 on = 166 – 167
to choose a movie, and then press the
<m> button.
zz
Press the <q><r> buttons or turn the
<5> dial to choose [c], and then press
the <m> button. The screen at left is
displayed.
2 Choose a printing method.
zz
Press the <o><p> buttons or turn
the <5> dial to choose [ ], and then
press the <q><r> buttons to choose the
printing method.
Y
P
O
3 Print the image.
C
Movie Printing Options
Single
Prints the current scene as a still image.
Sequence
Prints a series of scenes, a certain interval apart, on a single sheet of
paper. You can also print the folder number, file number, and elapsed
time for the frame by setting [Caption] to [On].
• To cancel printing in progress, press the <m> button.
• [ID Photo] and [Sequence] cannot be chosen on Canon PictBridgecompatible printers from CP720/CP730 and earlier models.
172
Printing Images
Still Images
Adding Images to the Print List (DPOF)
Batch printing (= 176) and ordering prints from a photo development
service can be set up on the camera. Choose up to 998 images on a
memory card and configure relevant settings, such as the number of copies,
as follows. The printing information you prepare this way will conform DPOF
(Digital Print Order Format) standards.
Still Images
Configuring Print Settings
Specify the printing format, whether to add the date or file number, and
other settings as follows. These settings apply to all images in the print list.
zz
Press the <n> button, and then
choose [Print Settings] on the [2] tab.
Choose and configure settings as desired
(= 38).
C
Standard
Print Type
Index
Both
Date
File No.
Clear DPOF
data
Y
P
O
One image is printed per sheet.
Smaller versions of multiple images are printed
per sheet.
Both standard and index formats are printed.
On
Images are printed with the shooting date.
Off
–
On
Images are printed with the file number.
Off
–
On
All image print list settings are cleared after
printing.
Off
–
173
Printing Images
• Not all of your DPOF settings may be applied in printing by the
printer or photo development service, in some cases.
• [ ] may be displayed on the camera to warn you that the memory
card has print settings that were configured on another camera.
Changing the print settings using this camera may overwrite all
previous settings.
• Setting [Date] to [On] may cause some printers to print the date
twice.
• Specifying [Index] will prevent you from choosing [On] for both [Date] and
[File No.] at the same time.
• The date is printed in a format matching setting details in [Date/Time] on the
[3] tab, accessible by pressing the <n> button (= 17).
• Index printing is not available on some Canon PictBridge-compatible printers
(sold separately).
Y
P
O
Still Images
Setting Up Printing for Individual Images
1 Choose [Select Images & Qty.].
C
zz
Press the <n> button, choose
[Select Images & Qty.] on the [2] tab,
and then press the <m> button.
2 Choose an image.
zz
Press the <q><r> buttons or turn the
<5> dial to choose an image, and then
press the <m> button.
XX
You can now specify the number of copies.
zz
If you specify index printing for the image, it
is labeled with a [ ] icon. To cancel index
printing for the image, press the <m>
button again. [ ] is no longer displayed.
174
Printing Images
3 Specify the number of prints.
zz
Press the <o><p> buttons or turn the <5>
dial to specify the number of prints (up to 99).
zz
To set up printing for other images and specify
the number of prints, repeat steps 2 – 3.
zz
Printing quantity cannot be specified for
index prints. You can only choose which
images to print, by following step 2.
zz
When finished, press the <n> button
to return to the menu screen.
Still Images
Setting Up Printing for a Range of Images
1 Choose [Select Range].
Y
P
O
zz
Following step 1 on = 174, choose
[Select Range] and press the <m>
button.
2 Choose images.
C
zz
Follow steps 2 – 3 on = 122 to specify
images.
3 Configure the print settings.
zz
Press the <o><p> buttons to choose
[Order], and then press the <m> button.
175
Printing Images
Still Images
Setting Up Printing for All Images
1 Choose [Select All Images].
zz
Following step 1 on = 174, choose
[Select All Images] and press the <m>
button.
2 Configure the print settings.
zz
Press the <q><r> buttons or turn the
<5> dial to choose [OK], and then press
the <m> button.
Still Images
Clearing All Images from the Print List
1 Choose [Clear All Selections].
Y
P
O
zz
Following step 1 on = 174, choose
[Clear All Selections] and press the <m>
button.
C
2 Confirm clearing the print list.
zz
Press the <q><r> buttons or turn the
<5> dial to choose [OK], and then press
the <m> button.
Still Images
Printing Images Added to the Print List (DPOF)
zz
When images have been added to the
176
print list (= 173 – 176), the screen
at left is displayed after you connect
the camera to a PictBridge-compatible
printer. Press the <o><p> buttons to
choose [Print now], and then simply press
the <m> button to print the images in the
print list.
zz
Any DPOF print job that you temporarily
stop will be resumed from the next image.
Printing Images
Still Images
Adding Images to a Photobook
Photobooks can be set up on the camera by choosing up to 998 images on a
memory card and importing them into the included software on your computer,
where they are stored in their own folder. This is convenient when ordering
printed photobooks online or printing photobooks with your own printer.
Choosing a Selection Method
zz
Press the <n> button, choose
[Photobook Set-up] on the [1] tab, and
then choose how you will select images.
Y
P
O
• [ ] may be displayed on the camera to warn you that the memory
card has print settings that were configured on another camera.
Changing the print settings using this camera may overwrite all
previous settings.
C
• After importing images to your computer, also refer to the Software Guide
(= 25) and the printer manual for further information.
Still Images
Adding Images Individually
1 Choose [Select].
zz
Following the previous procedure, choose
[Select] and press the <m> button.
177
Printing Images
2 Choose an image.
zz
Press the <q><r> buttons or turn the
<5> dial to choose an image, and then
press the <m> button.
XX
[ ] is displayed.
zz
To remove the image from the photobook,
press the <m> button again. [ ] is no
longer displayed.
zz
Repeat this process to specify other images.
zz
When finished, press the <n> button
to return to the menu screen.
Still Images
Adding All Images to a Photobook
1 Choose [Select All Images].
Y
P
O
zz
Following the procedure on = 177,
choose [Select All Images] and press the
<m> button.
C
2 Configure the print settings.
zz
Press the <q><r> buttons or turn the
<5> dial to choose [OK], and then press
the <m> button.
Still Images
Removing All Images from a Photobook
1 Choose [Clear All Selections].
zz
Following the procedure on = 177,
choose [Clear All Selections] and press
the <m> button.
2 Confirm clearing the photobook.
zz
Press the <q><r> buttons or turn the
<5> dial to choose [OK], and then press
the <m> button.
178
Still Images
Movies
Using an Eye-Fi Card
Before using an Eye-Fi card, always confirm that local use is permitted
(= 2).
Inserting a prepared Eye-Fi card enables automatic wireless transfer of
images to a computer or uploading to a photo-sharing website.
Images are transferred by the Eye-Fi card. Refer to the card’s user manual
or contact the manufacturer for instructions on preparing and using cards or
resolving transfer problems.
• When using an Eye-Fi card, keep the following points in mind.
-Cards may continue to transmit radio waves even when [EyeFi trans.] is set to [Disable] (= 180). Remove the Eye-Fi
card before entering hospitals, aircraft, or other areas where
transmission is prohibited.
-When troubleshooting image transfer issues, check the card and
computer settings. For details, refer to the card’s user manual.
-Poor Eye-Fi connections may cause image transfer to take a long
time, and transfer may be interrupted in some cases.
-Eye-Fi cards may become hot, due to their transfer functions.
-Battery power will be consumed faster than in normal use.
-Camera operation may become sluggish. To resolve this, try
setting [Eye-Fi trans.] to [Disable].
C
Y
P
O
Connection status of Eye-Fi cards in the camera can be checked on the
shooting screen (in regular information display mode) or playback screen (in
simple information display mode).
(Gray)
Not connected
Interrupted
(Blinking white)
Connecting
Not communicating
(White)
Connected
(Animated)
Transfer in progress*1
Error acquiring Eye-Fi card
information*2
*1 Power saving (= 34) on the camera is temporarily disabled during image transfer.
*2 Restart the camera. Repeated display of this icon may indicate a problem with the
card.
Images labeled with a [
] icon have been transferred.
179
Using an Eye-Fi Card
Checking Connection Information
Check the access point SSID used by the Eye-Fi card or the connection
status, as needed.
zz
Press the <n> button, choose
[Eye-Fi Settings] on the [3] tab, and then
press the <m> button.
zz
Choose [Connection info], and then press
the <m> button.
XX
The connection information screen is
displayed.
Disabling Eye-Fi Transfer
Configure the setting as follows to disable Eye-Fi transfer by the card, if
necessary.
Y
P
O
Choose [Disable] in [Eye-Fi trans.].
zz
Press the <n> button, choose
C
[Eye-Fi Settings] on the [3] tab, and then
press the <m> button.
zz
Choose [Eye-Fi trans.], and then choose
[Disable].
• [Eye-Fi Settings] is not shown unless an Eye-Fi card is in the
camera with its write-protect tab in the unlocked position. For this
reason, you cannot change settings for an inserted Eye-Fi card if
the write-protect tab is in the locked position.
180
9
Appendix
Y
P
O
Helpful information when using the camera
C
181
Troubleshooting
If you think there is a problem with the camera, first check the following.
If the items below do not solve your problem, contact a Canon Customer
Support Help Desk.
Power
Nothing happens when the power button is pressed.
• Confirm that new batteries of the correct type are inserted (= 15, 16).
• Confirm that the batteries are inserted facing the correct way (= 15).
• Confirm that the memory card/battery cover is fully closed (= 16).
• Dirty battery terminals reduce battery performance. Try cleaning the terminals with a
cotton swab and reinserting the batteries a few times.
Batteries are depleted quickly.
• Battery performance decreases at low temperatures. Try warming the batteries a little
by putting them in your pocket, for example, ensuring that the terminals do not touch
any metal objects.
The lens is not retracted.
Y
P
O
• Do not open the memory card/battery cover while the camera is on. Close the cover,
turn the camera on, and then turn it off again (= 16).
Display on a TV
Camera images look distorted or not displayed on a TV (= 163).
Shooting
Cannot shoot.
C
• In Playback mode (= 19), press the shutter button halfway (= 35).
Strange display on the screen under low light (= 36).
Strange display on the screen when shooting.
Note that the following display problems are not recorded in still images but are
recorded in movies.
• The screen may darken under bright light.
• The screen may flicker under fluorescent or LED lighting.
• Purplish banding may appear on the screen if you compose a shot that includes a
bright light source.
No date stamp is added to images.
• Configure the [Date Stamp] setting (= 52). Note that date stamps are not added to images
automatically, merely because you have configured the [Date/Time] setting (= 17).
• Date stamps are not added in shooting modes (= 198 – 199) in which this setting
cannot be configured (= 52).
182
Troubleshooting
[Charging the flash] is displayed when the shutter button is pressed,
and shooting is not possible (= 45).
[ ] is displayed when the shutter button is pressed halfway (= 45).
• Set [IS Mode] to [Continuous] (= 101).
• Raise the flash and set the flash mode to [h] (= 98).
• Increase the ISO speed (= 82).
• Mount the camera on a tripod or take other measures to keep it still. In this case, you
should set [IS Mode] to [Off] (= 101).
Shots are out of focus.
• Press the shutter button halfway to focus on subjects before pressing it all the way
down to shoot (= 35).
• Make sure subjects are within focusing range (= 205).
• Set [AF-assist Beam] to [On] (= 62).
• Confirm that unneeded functions such as macro are deactivated.
• Try shooting with focus lock or AF lock (= 93, 97).
Y
P
O
No AF frames are displayed and the camera does not focus when the
shutter button is pressed halfway.
• To have AF frames displayed and the camera focus correctly, try composing the
shot with higher-contrast subject areas centered before you press the shutter button
halfway. Otherwise, try pressing the shutter button halfway repeatedly.
C
Subjects in shots look too dark.
• Raise the flash and set the flash mode to [h] (= 98).
• Adjust brightness by using exposure compensation (= 81).
• Adjust contrast by using i-Contrast (= 83, 137).
• Use AE lock or spot metering (= 81, 82).
Subjects look too bright, highlights are washed-out.
• Lower the flash and set the flash mode to [!] (= 43).
• Adjust brightness by using exposure compensation (= 81).
• Use AE lock or spot metering (= 81, 82).
• Reduce the lighting on subjects.
Shots look too dark despite the flash firing (= 45).
• Shoot within flash range (= 205).
• Adjust brightness by using flash exposure compensation or changing the flash output
level (= 99, 107).
• Increase the ISO speed (= 82).
183
Troubleshooting
Subjects in flash shots look too bright, highlights are washed-out.
• Shoot within flash range (= 205).
• Lower the flash and set the flash mode to [!] (= 43).
• Adjust brightness by using flash exposure compensation or changing the flash output
level (= 99, 107).
White dots or similar image artifacts appear in flash shots.
• This is caused by light from the flash reflecting off dust or airborne particles.
Shots look grainy.
• Lower the ISO speed (= 82).
Subjects are affected by red-eye (= 56).
• Set [Red-Eye Lamp] to [On] (= 62) to activate the red-eye reduction lamp
(= 4) in flash shots. Note that while the red-eye reduction lamp is on (for about
one second), it is not possible to shoot, because the lamp is counteracting red-eye.
For best results, have subjects look at the red-eye reduction lamp. Also try increasing
the lighting in indoor scenes and shooting at closer range.
Y
P
O
• Edit images using red-eye correction (= 138).
Recording to the memory card takes too long, or continuous shooting
is slower.
• Use the camera to perform low-level formatting of the memory card (= 147).
C
Shooting settings or FUNC. menu settings are not available.
• Available setting items vary by shooting mode. Refer to “Functions Available in Each
Shooting Mode”, “FUNC. Menu”, and “Shooting Menu” (= 192 – 196).
Shooting Movies
The elapsed time shown is incorrect, or recording is interrupted.
• Use the camera to format the memory card, or switch to a card that supports highspeed recording. Note that even if the elapsed time display is incorrect, the length
of movies on the memory card corresponds to the actual recording time (= 146,
204).
[
] is displayed and shooting stops automatically.
The camera’s internal memory buffer filled up as the camera could not record to the
memory card quickly enough. Try one of the following measures.
• Use the camera to perform low-level formatting of the memory card (= 147).
• Lower the image quality (= 57).
• Switch to a memory card that supports high-speed recording (= 204).
Zooming is not possible.
• Zooming is not possible when shooting movies in [
184
] mode.
Troubleshooting
Playback
Playback is not possible.
• Image or movie playback may not be possible if a computer is used to rename files or
alter the folder structure. Refer to the Software Guide (= 25) for details on folder
structure and file names.
Playback stops, or audio skips.
• Switch to a memory card that you have performed low-level formatting on with the
camera (= 147).
• There may be brief interruptions when playing movies copied to memory cards that
have slow read speeds.
• When movies are played on a computer, frames may be dropped and audio may skip
if computer performance is inadequate.
Sound is not played during movies.
• Adjust the volume (= 24, 111) if you have activated [Mute] (= 142) or the
sound in the movie is faint.
Y
P
O
• No sound is played for movies shot in [
recorded in this mode.
Computer
] mode (= 72) because audio is not
Cannot transfer images to a computer.
C
When attempting to transfer images to the computer via a cable, try reducing the
transfer speed as follows.
• Press the <1> button to enter Playback mode. Hold the <n> button down as
you press the <o> and <m> buttons at the same time. On the next screen, press
the <q><r> buttons to choose [B], and then press the <m> button.
Eye-Fi Cards
Cannot transfer images (= 179).
185
On-Screen Messages
If an error message is displayed, respond as follows.
No memory card
• The memory card may be inserted facing the wrong way. Reinsert the memory card
facing the correct way (= 15).
Memory card locked
• The write-protect tab of the memory card is set to the locked position. Switch the
write-protect tab to the unlocked position (= 15, 180).
Cannot record!
• Shooting was attempted without a memory card in the camera. To shoot, insert a
memory card facing the correct way (= 15).
Memory card error (= 147)
• If the same error message is displayed even when you have inserted a formatted memory
card facing the correct way, contact a Canon Customer Support Help Desk (= 15).
Insufficient space on card
• There is not enough free space on the memory card to shoot (= 41, 65, 79,
103) or edit images (= 133 – 138). Either erase unneeded images (= 124) or
insert a memory card with enough free space (= 15).
Change the batteries (= 15)
No Image.
C
Y
P
O
• The memory card does not contain any images that can be displayed.
Protected! (= 120)
Unidentified Image/Incompatible JPEG/Image too large./Cannot play
back AVI/RAW
• Unsupported or corrupt images cannot be displayed.
• It may not be possible to display images that were edited or renamed on a computer,
or images shot with another camera.
Cannot magnify!/Cannot play back this content in Smart Shuffle/
Cannot rotate/Cannot modify image/Cannot register this image!/
Cannot modify/Cannot assign to category/Unselectable image.
• The following functions may be unavailable for images that were renamed or already
edited on a computer, or images shot with another camera. Note that starred (*)
functions are not available for movies. Magnify* (= 117), Smart Shuffle* (= 119),
Categorize (= 130), Rotate (= 127), Edit* (= 133 – 138), Assign as Start-up
Image* (= 144), Print List* (= 173), and Photobook Set-up* (= 177).
Invalid selection range
• When specifying a range for image selection (= 122, 125, 132, 175), you
attempted to choose an initial image that was after the final image, or vice-versa.
186
On-Screen Messages
Exceeded selection limit
• More than 998 images were selected for Print List (= 173) or Photobook Set-up
(= 177). Choose 998 images or less.
• Print List (= 173) or Photobook Set-up (= 177) settings could not be saved
correctly. Reduce the number of selected images and try again.
• You attempted to choose more than 500 images in Protect (= 120), Erase
(= 124), Favorites (= 129), My Category (= 130), Print List (= 173), or
Photobook Set-up (= 177).
Communication error
• An excessive amount of images (approx. 1,000) on the memory card prevented printing
or image transfer to a computer. To transfer the images, use a commercially available
USB card reader. To print, insert the memory card directly into the printer card slot.
Naming error!
• The folder could not be created or images could not be recorded, because the highest
supported folder number (999) for storing images on the card has been reached and
the highest supported image number (9999) for images in folders has been reached.
In the [3] menu, change [File Numbering] to [Auto Reset] (= 148), or format the
memory card (= 146).
Lens Error
Y
P
O
• This error may occur if the lens is held while it is moving, or when the camera is used
in dusty or sandy locations.
C
• Frequent display of this error message may indicate camera damage. In this case,
contact a Canon Customer Support Help Desk.
A camera error was detected (error number)
• If this error message is displayed immediately after a shot, the image may not have
been saved. Switch to Playback mode to check for the image.
• Frequent display of this error message may indicate camera damage. In this case,
write down the error number (Exx) and contact a Canon Customer Support Help Desk.
File Error
• Correct printing (= 166) may not be possible for photos from other cameras or
images that have been altered using computer software, even if the camera is
connected to the printer.
Print error
• Check the paper size setting (= 170). If this error message is displayed when the
setting is correct, restart the printer and complete the setting on the camera again.
Ink absorber full
• Contact a Canon Customer Support Help Desk to request assistance with ink
absorber replacement.
187
On-Screen Information
Shooting (Information Display)
Battery level
(= 189)
Camera orientation*
White balance
(= 84)
My Colors (= 86)
Drive mode
(= 88)
Self-timer (= 50)
Camera shake
warning (= 45)
Metering method
(= 82)
Eye-Fi connection
status (= 179)
Still image
compression
(= 101),
Resolution (= 55)
188
Y
P
O
Still images:
Recordable shots
(= 204)
Grid lines (= 59)
Movie resolution
(= 57)
Movies: Remaining
time (= 204)
Digital zoom
magnification
(= 49), Digital
tele-converter
(= 92)
Focusing range
(= 90)
Shooting mode
(= 192), Scene
icon (= 46)
Flash mode
(= 98)
C
Red-eye correction
(= 56)
Flash exposure
compensation /
Flash output level
(= 99, 107)
Spot AE point frame
(= 82)
AF frame (= 92)
Date stamp
(= 52)
ISO speed (= 82)
AE lock (= 81),
FE lock (= 100)
Exposure shift bar
Shutter speed
(= 104, 106)
Aperture value
(= 105, 106)
On-Screen Information
Exposure
compensation level
(= 81)
Exposure
compensation bar
(= 81)
i-Contrast (= 83)
Zoom bar (= 42)
*
Blink detection
(= 61)
AF lock (= 97),
Manual focus
(= 90)
IS mode icon
(= 47)
Exposure level
(= 106)
MF indicator
(= 91)
Time zone (= 150)
Image stabilization
(= 101)
Wind filter (= 58)
: Regular orientation,
: Held vertically
The camera detects the shooting orientation and adjusts settings for optimal shots.
Orientation is also detected during playback, and in either orientation, the camera
automatically rotates images as needed.
However, the orientation may not be detected correctly when the camera is pointed
straight up or down.
Battery Level
Y
P
O
An on-screen icon or message warns you when there is little battery power
left. No icon or message is shown unless the batteries are running out of
power.
Display
Change the batteries
C
Details
Nearly depleted—prepare replacement
batteries
Depleted—replace the batteries
189
On-Screen Information
Playback (Detailed Information Display)
My Category
(= 130)
Shooting mode
(= 192)
ISO speed
(= 82), Playback
speed (= 73)
Exposure
compensation level
(= 81), Exposure
shift level (= 77)
White balance
(= 84)
Histogram (= 112)
Image editing
(= 133 – 138)
Compression (image
quality) (= 101) /
Resolution (= 55,
57), MOV
(movies)
190
Y
P
O
Transferred via Eye-Fi (= 179)
Battery level
(= 189)
Metering method
(= 82)
Folder number - File
number (= 148)
Current image no. /
Total no. of images
Shutter speed (still
images) (= 104),
Image quality /
Frame rate (movies)
(= 57)
Aperture value
(= 105, 106),
Image quality
(movies) (= 57)
i-Contrast (= 83,
137)
C
Flash (= 98),
Flash exposure
compensation
(= 99)
Focusing range
(= 90)
File size
Still images:
Resolution (= 204)
Movies: Playback
time (= 204)
Protection (= 120)
Favorites (= 129)
My Colors (= 86,
136)
Red-eye correction
(= 56, 138)
Shooting date/time
(= 17)
On-Screen Information
• Some information may not be displayed when viewing images on a TV
(= 159).
Summary of Movie Control Panel in “Viewing” (= 110)
Exit
Play
Slow Motion (To adjust the playback speed, press the <q><r> buttons or turn
the <5> dial. No sound is played.)
Skip Backward* (To continue skipping backward, keep holding down the <m>
button.)
Previous Frame (For fast-rewind, keep holding down the <m> button.)
Next Frame (For fast-forward, keep holding down the <m> button.)
Y
P
O
Skip Forward* (To continue skipping forward, keep holding down the <m>
button.)
*
Edit (= 139)
c
Shown when the camera is connected to a PictBridge-compatible printer
(= 166).
C
*Displays the frame approx. 4 sec. before or after the current frame.
• To skip forward or back during movie playback, press the <q><r> buttons.
191
Functions and Menu Tables
Functions Available in Each Shooting Mode
Shooting Mode
Function
Exposure Compensation (= 81)
ISO Speed (= 82)
A
D
B
M
G
–
O
O
O
*1
–
–
O
O
O
O
O
O
O
O
O
–
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Self-Timer (= 50)
][$
Self-Timer Settings (= 51)
Delay*2
Shots*3
Flash (= 98)
h
Z
!
Av/Tv Settings (= 104, 105)
Aperture Value
Shutter Speed
Program Shift (= 81)
AE Lock/FE Lock (= 81, 100)*5
AE Lock (Movie)/Exposure Shift (= 77)
Focusing Range (= 90)
C
Y
P
O
e f(= 90)
Tracking AF (= 53)
Screen Display (= 36)
Information Display / No Information Display
–
–
–
O
O
O
O
–
–
O
O
–
O
–
–
O
O
–
O
O
–
–
–
O
O
–
–
–
O
–
O
O
–
–
O
O
O
–
–
–
O
O
–
–
–
–
–
–
–
–
–
–
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
*4
*1 Set in [Dark] and [Light].
*2 Cannot be set to 0 seconds in modes without selection of the number of shots.
*3 One shot (cannot be modified) in modes without selection of the number of shots.
*4 Not available, but switches to [Z] in some cases.
*5 FE lock not available in [!] flash mode.
192
Functions and Menu Tables
K
I
E
P
t
E
O
O
O
O
O
O
O
O
O
O
–
O
–
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
–
–
–
–
–
–
–
–
–
–
–
–
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
–
O
O
O
O
–
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
–
O
–
O
–
O
O
O
O
–
O
O
–
–
O
–
–
–
–
–
O
–
–
–
–
O
O
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
–
O
O
O
O
–
–
O
–
O
–
O
–
O
O
O
O
O
O
O
O
O
–
O
–
O
–
O
O
O
–
–
–
–
O
O
O
O
O
O Available or set automatically. – Not available.
C
–
–
–
–
–
Y
P
O
O
O
O
O
O
–
–
–
O
–
–
O
–
–
O
–
–
O
–
–
O
–
–
–
–
O
–
–
O
–
–
O
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
O
–
–
–
–
O
193
Functions and Menu Tables
FUNC. Menu
Shooting Mode
A
D
B
M
G
O
O
O
O
O
O
O
O
O
O
–
–
O
O
O
O
O
O
O
O
O
O
–
–
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
–
–
–
–
–
–
–
O
O
O
O
O
O
O
O
O
O
–
–
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
–
O
Function
White Balance (= 84)
My Colors (= 86)
*1
*1
*2
Drive Mode (= 88)
*3
Flash Exposure Compensation (= 99)
Flash Output Level (= 107)
Metering Method (= 82)
Still Image Aspect Ratio (= 54)
Resolution (= 55)
C
Y
P
O
–
–
–
–
–
–
O
O
O
O
–
O
Compression (= 101)
O
O
O
O
–
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
Movie Quality (= 57)
*1 White balance is not available. *2 Set in a range of 1 – 5: contrast, sharpness, color saturation, red, green, blue, and skin tone. *3 [ ] is set with [f], AF lock, or [t]. *4 Only [ ] and [ ] are available. *5 Synchronizes with the aspect ratio setting and is automatically set (= 74).
194
Functions and Menu Tables
K
I
E
P
t
E
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
–
–
–
–
–
–
–
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
–
–
–
–
–
–
–
–
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
–
–
–
–
O
–
–
O
–
–
O
–
–
O
–
–
O
–
–
O
–
–
O
–
–
O
–
–
O
–
–
O
–
–
–
–
–
–
–
–
O
O
O
O
O
O
O
O
O
O
O
O
O
–
–
–
–
–
–
–
–
–
–
–
–
–
O
O
–
O
O
C
O
–
*4
–
O
O
O
O
–
–
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
–
–
–
–
–
–
O
O
O
–
–
O
–
–
–
–
–
–
–
–
–
–
–
O
O
–
O
O
–
–
–
–
–
–
O
O
O
–
Y
P
O
–
–
–
–
–
–
–
–
–
–
–
–
–
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
*5
O
O
O
O
O
O
O
O
O
O
O
O
O
*5
O
O
O
O
O
O
–
O Available or set automatically. – Not available.
195
Functions and Menu Tables
4 Shooting Menu
Shooting Mode
Function
AF Frame (= 92)
Center
Face AiAF*1
Tracking AF
AF Frame Size*3
Normal
Small
Digital Zoom (= 49)
Standard
Off
Digital Tele-converter (1.6x/2.0x)
AF-Point Zoom (= 60)
On
Off
Servo AF (= 95)
On
Off*4
Continuous AF (= 96)
On
Off
AF-assist Beam (= 62)
On
Off
MF-Point Zoom (= 90)
On
Off
Safety MF (= 90)
On
Off
C
A
D
B
M
G
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
–
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
–
O
Y
P
O
*2
*1 Operation when no faces are detected varies by shooting mode. *2 Only available by
pressing the <o> button (= 53). *3 Available when the AF frame is set to [Center]. *4 [On] when subject movement is detected in <A> mode.
196
Functions and Menu Tables
K
I
E
P
t
E
O
O
O
–
O
–
O
O
O
O
O
O
O
–
–
O
–
–
–
–
–
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
–
O
O
–
–
O
O
O
O
O
–
O
–
–
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
–
–
O
–
O
O
–
O
O
–
–
O
–
–
O
–
–
O
–
–
O
–
–
O
–
–
O
–
O
O
–
O
O
–
O
O
–
O
O
O
O
O
O
O
O
–
O
–
O
–
O
–
O
O
O
O
O
O
O
O
O
–
O
–
O
O
O
–
O
O
O
O
O
–
O
–
O
O
O
O
O
O
O
O
O
–
O
–
O
O
O
O
–
–
O
O
O
–
O
C
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
–
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
–
O
O
O
O
O
–
O
–
O
–
O
–
O
O
O
O
O
O
O
O
O
–
O
–
O
O
O
–
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O Available or set automatically. – Not available.
–
O
Y
P
O
197
Functions and Menu Tables
Shooting Mode
Function
Flash Settings (= 56, 62, 99, 107)
Auto
Flash Mode
Manual
Flash Exp. Comp
Flash Output
On
Red-Eye Corr.
Off
Red-Eye Lamp
On/Off
On
Safety FE
Off
i-Contrast (= 83)
Auto
Off
Safety Shift (= 105)
On
Off
Wind Filter (= 58)
On/Off
Review (= 63)
Off/Quick/2 – 10 sec./Hold
Review Info (= 64)
Off/Detailed/Focus Check
Blink Detection (= 61)
On
Off
Grid Lines (= 59)
On/Off
IS Mode (= 101)
Off/Continuous
Shoot Only
Date Stamp (= 52)
Off
Date / Date & Time
C
198
A
D
B
M
G
–
O
–
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
–
O
O
O
O
O
O
–
–
–
–
O
O
O
O
O
–
–
–
O
O
O
O
–
O
O
O
O
O
O
O
O
–
O
O
–
–
O
O
O
O
O
–
O
–
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
Y
P
O
Functions and Menu Tables
K
I
E
P
t
E
O
–
–
–
O
O
O
O
–
O
–
–
–
O
O
O
O
–
O
–
–
–
O
O
O
O
–
O
–
–
–
O
O
O
O
–
–
–
–
–
–
–
–
–
–
O
–
–
–
–
O
O
O
–
O
–
–
–
–
O
O
O
–
O
–
–
–
–
O
O
O
–
O
–
–
–
–
O
O
O
–
O
–
–
–
–
O
O
O
–
O
–
–
–
–
O
O
O
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
O
–
O
O
–
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
–
O
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
–
O
O
O
O
O
O
O
O
O
O
O
O
–
–
O
O
O
O
O
O
O
O
–
O
–
O
–
O
–
O
–
O
O
O
O
O
O
O
–
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
–
O
O
O
O
O
–
O
O
O
O
O
–
O
O
O
O
O
O
O
O
–
–
–
–
–
O
–
–
O Available or set automatically. – Not available.
C
O
Y
P
O
199
Functions and Menu Tables
3 Set up Menu
Item
Ref. Page
Item
Ref. Page
Mute
= 142
Create Folder
= 148
Volume
= 142
Lens Retract
= 149
Sound Options
= 143
Power Saving
= 34, 149
Hints & Tips
= 143
Units
= 151
Date/Time
= 17
Video System
= 163
Time Zone
= 150
Ctrl via HDMI
= 161
LCD Brightness
= 144
Eye-Fi Settings
= 179
Start-up Image
= 144, 145
Format
= 146, 147
File Numbering
= 148
C
1 Playback Menu
Item
Y
P
O
Certification Logo Display
= 151
Language
= 19
Reset All
= 152
Ref. Page
Smart Shuffle
= 119
Slideshow
Item
Ref. Page
Red-Eye Correction
= 138
= 118
Cropping
= 134
Erase
= 124
Resize
= 133
Protect
= 120
My Colors
= 136
Rotate
= 127
Scroll Display
= 111
Favorites
= 129
Auto Rotate
= 128
My Category
= 130
Resume
= 111
Photobook Set-up
= 177
Transition
= 111
i-Contrast
= 137
200
Functions and Menu Tables
2 Print Menu
Item
Print
Ref. Page
–
Item
Ref. Page
Select All Images
= 176
Select Images & Qty.
= 174
Clear All Selections
= 176
Select Range
= 175
Print Settings
= 173
C
Y
P
O
201
Handling Precautions
• The camera is a high-precision electronic device. Avoid dropping it or
subjecting it to strong impact.
• Never bring the camera near magnets, motors, or other devices that
generate strong electromagnetic fields, which may cause malfunction or
erase image data.
• If water droplets or dirt adheres to the camera or screen, wipe with a dry
soft cloth, such as an eyeglass cloth. Do not rub hard or apply force.
• Never use cleaners containing organic solvents to clean the camera or
screen.
• Use a blower brush to remove dust from the lens. If cleaning is difficult,
contact a Canon Customer Support Help Desk.
• To prevent condensation from forming on the camera after sudden
temperature changes (when the camera is transferred from cold to warm
environments), put the camera in an airtight, resealable plastic bag and
let it gradually adjust to the temperature before removing it from the bag.
Y
P
O
• If condensation does form on the camera, stop using it immediately.
Continuing to use the camera in this state may damage it. Remove the
batteries and memory card, and wait until the moisture has evaporated
before resuming use.
C
202
Specifications
Camera Effective
Pixels (Max.)
Lens Focal Length
LCD Monitor
File Format
Data Type
Interface
Power Source
Dimensions (Based
on CIPA Guidelines)
Weight (Based on
CIPA Guidelines)
Approx. 16 million pixels
16x zoom: 5.0 (W) – 80.0 (T) mm
(35mm film equivalent: 28 (W) – 448 (T) mm)
3.0 type color TFT LCD
Effective Pixels: Approx. 230,000 dots
Design rule for Camera File system, DPOF (version 1.1) compliant
Still Images: Exif 2.3 (JPEG)
Movies: MOV (Image data: H.264; Audio data: Linear PCM (stereo))
Hi-speed USB
HDMI output
Analog audio output (stereo)
Analog video output (NTSC/PAL)
AA alkaline batteries (AA NiMH batteries (Canon NB-3AH)) x2
AC Adapter Kit ACK800
• However, connection requires DC Coupler DR-DC10, sold
separately
111.0 x 72.5 x 44.1 mm (4.37 x 2.85 x 1.74 in.)
Y
P
O
Approx. 291 g (approx. 10.3 oz.; including batteries and
memory card)
Approx. 243 g (approx. 8.57 oz.; camera body only)
C
Number of Shots/Recording Time, Playback Time
Power Source
Alkaline Batteries (Supplied)
Number of Shots
Movie Recording
Time*1
Continuous
Shooting*2
Playback Time
Approx. 140
NiMH Batteries (Sold
Separately)
Approx. 380
Approx. 30 minutes
Approx. 90 minutes
Approx. 1 hour, 10 minutes
Approx. 2 hours, 40 minutes
Approx. 7 hours
Approx. 10 hours
*1Time under default camera settings, when normal operations are performed, such as
shooting, pausing, turning the camera on and off, and zooming.
*2Time available when shooting the maximum movie length (until recording stops
automatically) repeatedly.
•The number of shots that can be taken is based on measurement guidelines of the
Camera & Imaging Products Association (CIPA).
•Under some shooting conditions, the number of shots and recording time may be less
than mentioned above.
•The number of shots and recording time that can be taken may vary widely depending
on the brand of alkaline batteries used.
•Number of shots/time with fully charged NiMH batteries.
203
Specifications
Number of 4:3 Shots per Memory Card
Recording Pixels
Compression
Ratio
(Large)
16M/4608x3456
(Medium 1)
8M/3264x2448
(Medium 2)
2M/1600x1200
(Small)
0.3M/640x480
Number of Shots per Memory Card
(Approx. shots)
8 GB
32 GB
1131
4567
1903
7684
2252
9094
3721
15020
7442
30040
12927
52176
27291
110150
40937
165225
•The values in the table are measured according to Canon standards and may change
depending on the subject, memory card and camera settings.
•The values in the table are based on 4:3 aspect ratio. If the aspect ratio is changed
(= 54), more images can be shot because the data size per image will be smaller
than with 4:3 images. However, since [ ] 16:9 images have a setting of 1920 x 1080
pixels, their data size will be larger than 4:3 images.
C
Y
P
O
Recording Time per Memory Card
Image Quality
Recording Time per Memory Card
8 GB
32 GB
49 min. 18 sec.*1
3 hr. 19 min. 03 sec.*2
1 hr. 28 min. 59 sec.
5 hr. 59 min. 10 sec.
*127 min. 28 sec. for iFrame movies (= 78).
*21 hr. 50 min. 52 sec. for iFrame movies (= 78).
•The values in the table are measured according to Canon standards and may change
depending on the subject, memory card and camera settings.
•Recording will automatically stop when the clip file size reaches 4 GB, or when the
recording time reaches approximately 29 minutes and 59 seconds when shooting in [
], and approximately 1 hour when shooting in [ ].
•Recording may stop even if the maximum clip length has not been reached on some
memory cards. SD Speed Class 6 or higher memory cards are recommended.
204
Specifications
Flash Range
Maximum wide angle (j)
50 cm – 3.0 m (1.6 – 9.8 ft.)
Maximum telephoto (i)
60 cm – 2.0 m (2.0 – 6.6 ft.)
Shooting Range
Shooting
Mode
A
Focusing
Maximum Wide Angle (j)
Range
1 cm (0.4 in.) – infinity
–
Other modes
e*
f*
5 cm (2.0 in.) – infinity
1 cm (0.4 in.) – 50 cm (1.6 ft.)
1 cm (0.4 in.) – infinity
Maximum Telephoto (i)
60 cm (2.0 ft.) – infinity
60 cm (2.0 ft.) – infinity
–
60 cm (2.0 ft.) – infinity
*Not available in some shooting modes.
Continuous Shooting Speed
Shooting Mode
G
Shutter Speed
Y
P
O
Continuous Shooting Mode
Speed
Approx. 0.8 shots/sec.
W
C
–
Approx. 0.5 shots/sec.
Approx. 0.6 shots/sec.
Approx. 2.8 shots/sec.
<A> mode, automatically set range 1 – 1/3200 sec.
Range in all shooting modes
15 – 1/3200 sec.
15, 13, 10, 8, 6, 5, 4, 3.2, 2.5, 2, 1.6, 1.3, 1,
0.8, 0.6, 0.5, 0.4, 0.3, 1/4, 1/5, 1/6, 1/8, 1/10,
1/13, 1/15, 1/20, 1/25, 1/30, 1/40, 1/50, 1/60,
<M> mode available values (sec.)
1/80, 1/100, 1/125, 1/160, 1/200, 1/250, 1/320,
1/400, 1/500, 1/640, 1/800, 1/1000, 1/1250,
1/1600, 1/2000, 1/2500, 1/3200
205
Specifications
Aperture
f/number
<B> mode available values*
f/3.5 – f/8.0 (W), f/5.9 – f/8.0 (T)
f/3.5, f/4.0, f/4.5, f/5.0, f/5.6, f/5.9, f/6.3, f/7.1,
f/8.0
*Depending on the zoom position, some aperture values may not be available.
• All data is based on tests by Canon.
• Camera specifications or appearance are subject to change without
notice.
C
206
Y
P
O
Index
A
AC adapter kit............................. 157, 164
Accessories........................................ 157
AE lock................................................. 81
AF frames............................................. 92
AF lock................................................. 97
Aspect ratio.......................................... 54
AUTO mode (shooting mode)... 20, 36, 42
Av (shooting mode)............................ 105
Setting............................................ 17
World clock................................... 150
DC coupler......................................... 157
Defaults " Reset all
DIGITAL CAMERA Solution Disk............ 2
Digital tele-converter............................ 92
Digital zoom.......................................... 49
Discreet mode (shooting mode)........... 76
Display language.................................. 19
DPOF.................................................. 173
Drive mode........................................... 88
B
Batteries....................................... 15, 157
" Date/time (date/time battery)
Battery and charger kit................. 157
Level............................................. 189
Power saving.................................. 34
Battery and charger kit....................... 157
Y
P
O
Black and white images........................ 86
Blink detection...................................... 61
C
C
E
Editing
Cropping....................................... 134
i-Contrast...................................... 137
My Colors..................................... 136
Red-eye correction....................... 138
Resizing images........................... 133
Erasing............................................... 124
Camera
Reset all....................................... 152
Camera shake.................................... 101
Center (AF frame mode)...................... 93
Clock.................................................... 40
Color (white balance)........................... 84
Compression ratio (image quality)...... 101
Continuous shooting............................. 88
Creative filters (shooting mode)........... 71
Cropping............................................. 134
Custom white balance.......................... 85
Error messages.................................. 186
Exposure
AE lock........................................... 81
Compensation................................ 81
FE lock......................................... 100
Eye-Fi cards................................... 2, 179
F
Face AiAF (AF frame mode)................. 93
Face self-timer (shooting mode)........... 69
Favorites............................................. 129
FE lock............................................... 100
File numbering.................................... 148
Fireworks (shooting mode)................... 68
D
Fish-eye effect (shooting mode)........... 72
Date/time
Adding date stamps....................... 52
Changing........................................ 18
Date/time battery.......................... 156
Flash
Flash exposure compensation....... 99
On.................................................. 98
Slow synchro.................................. 98
207
Index
M
Focus check........................................113
Focusing
AF frames....................................... 92
AF lock........................................... 97
AF-point zoom................................ 60
Servo AF........................................ 95
Focusing range
Macro............................................. 90
Manual focus.................................. 90
Focus lock............................................ 93
FUNC. menu
Basic operations............................. 37
Table............................................. 194
G
Grid lines.............................................. 59
H
Household power............................... 164
I
C
i-Contrast...................................... 83, 137
iFrame movies (movie mode)............... 78
Macro (focus mode)............................. 90
Magnified display.................................117
Manual focus (focus mode).................. 90
Memory cards......................................... 2
Recording time............................. 204
Menu
Basic operations............................. 38
Table............................................. 192
Metering method.................................. 82
Miniature effect (shooting mode).......... 72
Monochrome (shooting mode)............. 75
Movies
Editing.......................................... 139
Image quality (resolution/frame rate).................... 57
Recording time............................. 204
M (shooting mode)............................. 106
Y
P
O
My Category....................................... 130
My Colors..................................... 86, 136
P
Image quality " Compression ratio
(image quality)
Package contents................................... 2
Images
Display period................................ 63
Erasing......................................... 124
Playback " Viewing
Protecting..................................... 120
Indicator................................................ 40
PictBridge................................... 158, 166
Interface cable.................................. 2, 28
ISO speed............................................ 82
L
Lamp.................................................... 62
Live View Control (shooting mode)....... 66
Low-light (shooting mode).................... 67
208
Photobook set-up............................... 177
Playback " Viewing
Portrait (shooting mode)....................... 67
Poster effect (shooting mode).............. 71
Power " AC adapter kit
" Batteries
" Battery and charger kit
Power saving........................................ 34
Clock.............................................. 40
Printing............................................... 166
Program AE.......................................... 80
Protecting........................................... 120
P (shooting mode)................................ 80
Index
R
T
Red-eye correction....................... 56, 138
Terminal...................... 159, 163, 165, 166
Reset all............................................. 152
Toy camera effect (shooting mode)...... 74
Resizing images................................. 133
Tracking AF.................................... 53, 94
Resolution (image size)........................ 55
Traveling with the camera.................. 150
Rotating.............................................. 127
Troubleshooting.................................. 182
TV display........................................... 159
S
Saving images to a computer............... 27
Screen
Display language............................ 19
Icons..................................... 188, 190
Menu " FUNC. menu, Menu
SD/SDHC/SDXC memory cards
" Memory cards
Searching............................................115
V
Viewing................................................. 23
Image search................................115
Index display.................................114
Magnified display..........................117
Single-image display...................... 23
Slideshow......................................118
Smart Shuffle................................119
TV display.................................... 159
Y
P
O
Self-timer.............................................. 50
2-second self-timer......................... 51
Customizing the self-timer.............. 51
Face self-timer (shooting mode).... 69
Sepia tone images................................ 86
C
Tv (shooting mode)............................ 104
Servo AF............................................... 95
Shooting
Shooting date/time " Date/time
Shooting information.................... 188
Slideshow............................................118
W
White balance (color)........................... 84
World clock......................................... 150
Wrist strap " Strap
Z
Zoom........................................ 20, 42, 49
Smart Shuffle.......................................119
Snow (shooting mode)......................... 68
Software
DIGITAL CAMERA Solution Disk..... 2
Installation...................................... 27
Saving images to a computer......... 29
Sounds............................................... 142
Stereo AV cable.................................. 162
Strap................................................. 2, 14
Super vivid (shooting mode)................. 71
209
C
210
Y
P
O
MEMO
C
Y
P
O
211
USA and Canada only:
The Nickel-Metal Hydride battery is recyclable.
Please call 1-800-8-BATTERY for information on how to recycle this
battery.
FCC Notice
(Digital Camera, Model PC1816 systems)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions;
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for Class
B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
C
Y
P
O
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
The cable with the ferrite core provided with the digital camera must be used with this
equipment in order to comply with Class B limits in Subpart B of Part 15 of the FCC
rules.
Do not make any changes or modifications to the equipment unless otherwise
specified in the manual. If such changes or modifications should be made, you could
be required to stop operation of the equipment.
Canon U.S.A., Inc.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
Tel No. (516) 328-5600
212
Canadian Radio Interference Regulations
This Class B digital apparatus complies with Canadian ICES-003.
For CA, USA only
Included lithium battery contains Perchlorate Material - special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate/ for details.
Trademark Acknowledgments
• The SDXC logo is a trademark of SD-3C, LLC.
• This device incorporates exFAT technology licensed from Microsoft.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
• The iFrame logo and the iFrame symbol are trademarks of Apple Inc.
About MPEG-4 Licensing
This product is licensed under AT&T patents for the MPEG-4 standard
and may be used for encoding MPEG-4 compliant video and/or decoding
MPEG-4 compliant video that was encoded only (1) for a personal and
non-commercial purpose or (2) by a video provider licensed under the AT&T
patents to provide MPEG-4 compliant video.
No license is granted or implied for any other use for MPEG-4 standard.
C
Y
P
O
*Notice displayed in English as required.
Disclaimer
• Reprinting, transmitting, or storing in a retrieval system any part of this
guide without the permission of Canon is prohibited.
• Canon reserves the right to change the contents of this guide at any time
without prior notice.
• Illustrations and screenshots in this guide may differ slightly from the
actual equipment.
• The above items notwithstanding, Canon accepts no liability for damages
due to mistaken operation of the products.
213
C
CDD-E494-010 Y
P
O
©CANON INC. 2012
Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Download PDF

advertisement