splashlight® led wall washer

splashlight® led wall washer
®
120V
AC
DMX
COMPATIBLE
SPLASHLIGHT® LED WALL WASHER
COLOR-CHANGING
DRY/WET LOCATION
SPECIFICATION SHEET
• Die-cast aluminum body &
tempered glass
• IP65 wet/outdoor
• 150° rotary angle
• Floor mountable
• DMX-512 controllable
SPECIFICATIONS
L 13.11 in.
(330mm)
Input Voltage ¹ : 100-256VAC, 50/60Hz
Power Connection: AC power plug (56 in. length)
Operating Voltage: 24V DC
Power Consumption: 53.5W
LED Chip Type: Edison
LED Chip Beam Angle: 45°
Mounting ² : Integrated 150° rotary surfacemount base w/ (2x) 5/16 in. mounting holes
(Floor mount only)
Maximum Run: 10 fixtures (expandable with
use of 8-Way DMX Splitter)
Connections: 1ea. male/female wet location
3-pin M14 cables (15 in. length). M14-to-XLR-3
adapter cables also included
Item #
CCT
(Kelvin)
Lumens ⁷
LED Chips
Efficacy ⁸
(lm/W)
-
1304
R=12, B=12, G=12
24.4
DI-0480
Note ¹
Note ²
Note ³
Note ⁴
150°
Rotary Angle
W 5.79 in.
(147mm)
Note ⁵
Note ⁶
Only UL Listed for connection with a 120VAC, 15- or 20-ampere branch circuit.
This fixture is intended for floor mounting only. Do not mount to walls or ceilings.
Not compatible with standard High Voltage AC dimming controls.
Do not install product in an environment outside the listed ambient temperature. Ensure adequate airflow and heatsinking is
considered when mounting/installing. Exceeding the maximum ambient temperature may damage LED chips by reducing the
total lamp life, lumen output, and/or adversely impact color consistency.
Operating temperature is measured according to the minimum and maximum ambient temperature environment.
When installing outdoors or in a damp location, ensure water-resistant end caps are connected to all wet location 3-pin M14
cables. If attaching XLR-3 DMX adapter cables seal all standard XLR-3 connections with 1.25” heat shrink and finish with
waterproof tape (not included). Do not use liquid sealants of any kind.
Lumen value measured in accordance to IES LM-79-08. LED chips have a luminous flux range with a tolerance of +/- 5%.
Efficacy value referenced from IES LM-79-08.
H 8.27 in.
(210mm)
Note ⁷
Note ⁸
Dimmable ³ : May be dimmed/controlled using
on-board controls or with a compatible DMX512 controller
Ambient Temp ⁴ : -4° ~ 104° F (-20° ~ 40° C)
Operating Temp ⁵ : -4° ~ 131° F (-20° ~ 55° C)
Housing / Cooling: Die-cast aluminum casing;
tempered glass / cooling by free air convection
Environment ⁶ : IP65 wet/outdoor
Dimensions: 13.11 x 5.79 x 8.27 in. (L x W x H)
Weight: 9.48 lbs.
Certifications: UL Listed (US & Canada) ANSI/
UL 153, ANSI/UL 8750 - Light Emitting Diode
Luminaires, Portable. E466305
Item #:
SPLASHLIGHT® SERIES
Project:
1 OF 5
SS112415-3.0
PHOTOMETRICS*
SPLASHLIGHT RGB
DI-0480
POLAR CANDELA DISTRIBUTION GRAPH
180
120
150
ACROSS
45
ALONG
90
650
60
1300
1950
0
30
INTENSITY(CANDLEPOWER) SUMMARY
ANGLE ALONG
0
2169
5
2043
10
1763
15
1384
20
984
25
644
30
429
35
326
40
265
45
208
50
138
55
74
60
36
65
17
70
8
75
3
80
0
85
0
90
0
BEAM SIDE
22.5
45
2169 2169
2044 2045
1764 1759
1373 1348
963
940
626
613
418
413
315
317
254
259
197
206
130
139
70
76
35
37
17
19
8
9
3
4
0
0
0
0
0
0
67.5 ACROSS
2169 2169
2060 2081
1771 1788
1361 1378
949
960
608
616
411
421
318
332
263
276
210
219
143
147
79
81
39
40
20
20
10
10
4
4
1
1
0
0
0
0
ZONAL LUMENS AND PERCENTAGES
ZONE
0-30
0-40
0-60
0-90
40-90
60-90
90-180
0-180
LUMENS
850
1053
1281
1304
251
24
0
1304
% LUMINAIRE
65.19
80.74
98.16
100.00
19.26
1.84
0.00
100.00
Cone Of Light Tabulation
Mounting Height
(Feet)
Footcandles at
Nadir
4.00
135
2.39
6.00
60.2
3.58
8.00
33.8
4.77
10.0
21.7
5.97
12.0
15.0
7.16
14.0
11.1
8.35
16.0
8.46
9.55
Diameter (Feet)
* Photometric data complies with LM-79-08, ANSI C82.77-02.
SPLASHLIGHT® SERIES
2 OF 5
SS112415-3.0
DMX CONTROLLERS
The following DMX Controllers may be utilized with our DMX fixtures and accessories.
Item #
Type
Description
This simple and intuitive DMX controller
commands up to four zones with WiFi
connectivity to a mobile device.
DI-1917
DMX Wi-Fi WallMount Controller
DI-1726
Nicolaudie STICK 1
DMX Color Controller
Our most sophisticated unit offers professionalgrade DMX512 control in a user-friendly control
pad.
DI-1720
Nicolaudie STICK 2
DMX Color Controller
Sophisticated and modern touch-sensitive
keypad selects mode, speed, and dimming.
DI-1727
Nicolaudie Easy Stand
Alone DMX LED Color
Controller
Program lighting scenes from a computer to
the independent free-standing controller.
DI-1808-K
SQUARE-PRO
Junction Box
Image
Included with the following controllers: DMX
WiFi Wall Mount Zone LED Controller, Nicolaudie
STICK 1 Controller, and Nicolaudie STICK 2
Controller. Also sold separately.
Features 3x 0.5 in. and 5x 0.75 in. knockouts.
Dimensions: 2.83 x 1.89 x 2.83 (L x D x H)
Note: accessories sold separately
SPLASHLIGHT® SERIES
3 OF 5
SS112415-3.0
DMX ACCESSORIES
The following DMX Accessories may be utilized with our DMX fixtures and controllers.
Item #
DI-1918
Type
Description
DMX 4-Channel
Decoder
Pair with a DMX controller to control solid color,
RGB, and RGBW LED fixtures. Features a
digital display for easy addressing.
DI-0820 (female)
DI-0821 (male)
Wireless DMX
Transmitter/Receiver
Wirelessly connects DMX devices: Fixture to
fixture, fixture to controller, and decoder to
decoder. Features XLR-3 connetions.
DI-1804
DMX 8-Way Splitter
Amplifies and splits a DMX signal up to 8 ways.
Features 1x male XLR-3 input connection, and
8x female XLR-3 output connections.
DI-1803
DMX XLR-3
Connector Pair
Utilize this XLR-3 connector pair to create
custom length DMX extensions. Sold by the
pair (male/female). Male: 2.8 x .71 in. (L x Dia.).
Female: 2.4 x .71 in. (L x Dia.)
DI-1806
XLR-3 to RJ45
Adapter Connector
Pair
Converts RJ45 data cables to XLR-3 DMX
connections. Sold by the pair (male/female)
Male & Female: 2.58 x .87 x .98 in. (L x W x H)
DI-1809
20 ft. DMX XLR-3
Extension Cable
Creates an extension between DMX fixtures
and accessories. Features XLR-3 connections.
Wire: 18/3 AWG. Male connection: 2.8 x .71 in.
(L x Dia.) Female: 2.4 x .71 in. (L x Dia.).
DI-1807
RJ45 Coupler
Female-to-female accessory quickly connects
two RJ45 accessories. Dimensions: 1.22 x .44
x .87 in. (L x W x H)
DI-1805
RJ45 Splice Cable
Lead wires connect to wall-mount DMX
controllers while RJ45 plug connects to DMX
accessories. Dimensions: 6.5 x .4 x .6 (L x W x H)
DI-1811
XLR-3 to RJ45
Adapter Cable Pair
Converts RJ45 port of 4-Channel DMX Decoder
to a standard XLR-3 connection. Sold by the pair
(male/female). Dimensions: 20 x .71 (L x Dia)
DI-1911
RJ45 Extension Cable
Creates a 10 ft. extension between DMX fixtures
and accessories utilizing RJ45 connections.
Image
Note: accessories sold separately
SPLASHLIGHT® SERIES
4 OF 5
SS112415-3.0
ADDITIONAL RESOURCES
Visit the online product page at www.DiodeLED.com for additional resources including:
• WET LOCATION LED WALL WASHER Installation Guide
For system diagrams and full installation instructions.
• Voltage Drop Charts
Use to specify appropriate wire gauge for installation. Available at the ‘Tools & Resources’ page at www.DiodeLED.com.
SAFETY & DISCLOSURES
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Install in accordance with the National Electric Code and local regulations.
This product is intended to be installed and serviced by a qualified, licensed electrician.
Do not disassemble or modify this product. Doing so will void your warranty.
This fixture is not compatible with any traditional dimming controls. Wall washers can only be controlled/dimmed with the on-board interface or with
an external DMX controller. Please contact customer service for additional information.
Ensure all adjusting screws on mounting brackets and fixtures are properly secured prior to permanent installation.
This fixture is intended for floor mounting only. Do not mount to walls or ceilings.
It is recommended to power this fixture by a GFCI protected circuit.
This fixture is IP65 rated.
When installing outdoors or in a wet location, ensure water-resistant end caps are connected to all exposed wet location 3-pin M14 connections. If
attaching XLR-3 adapter cables seal all XLR-3 DMX connections with 1.25” wide heat shrink and finish with waterproof tape (not included). Do not
use liquid sealants of any kind.
This fixture is not to be used in or around chlorinated, treated or salt water due to the corrosive and degrading qualities of chlorine, saline, and other
chemicals on the fixture components. Keep at least 16 feet away from pools and spas.
Do not install product in an environment outside the listed ambient temperature. Ensure adequate airflow and heatsinking is considered when
mounting/installing.
Operating temperature is measured according to the minimum and maximum ambient temperature environment. Exceeding the maximum ambient
temperature may damage LED chips by reducing the total lamp life, lumen output, and/or adversely impact color consistency.
Ensure adequate airflow and heatsinking is considered when mounting/installing. Exceeding the maximum operating temperature may damage LED
chips by reducing the total lamp life, lumen output, and/or adversely impact color consistency.
Actual color may vary from what is pictured on this sheet and other print materials due to the limitations of photographic processes.
Lighting technology has some amount of gradual light degradation (output and/or color) over the lifespan of the products. Diode LED products are
designed to minimize degradation, but some light degradation and color shift is a normal part of the life span of any LED lighting system.
We reserve the right to modify and improve the design of our fixtures without prior notice. We cannot guarantee to match existing installed fixtures
for subsequent orders or replacements in regards to product appearance, CCT, or lumen output.
WARRANTY INFORMATION
Limited Warranty
This LED fixture has a two (2) year limited warranty from the date of shipment. This warranty does not include the additional accessories referenced
in this specification sheet. Complete warranty details for fixtures and additional accessories are available at www.DiodeLED.com under the ‘Tools &
Resources’ tab. For warranty related questions, please contact customer service.
Consumer’s Acknowledgment
Diode LED stands behind its products when they are used properly and according to our specifications. By purchasing our products, the purchaser
agrees and acknowledges that lighting design, configuration and installation is a complex process, wherein seemingly minor factors or changes in
layout and infield adjustments can have a significant impact on an entire system. Choosing the right components is essential. Diode LED is able to
work with the original purchaser to make an appropriate product selection to the extent of the limited information that the customer can provide, but
it is virtually impossible for Diode LED to design a system that foresees every unknown factor. For this reason, this Warranty does not cover problems
caused by improper design, configuration or installation issues. Any statement from a Diode LED employee or agent regarding a customer’s bill of
goods and/or purchase order is NOT an acknowledgment that the products purchased are designed and configured correctly. The purchaser agrees
and acknowledges that it is the customer’s responsibility to adhere strictly to all information contained in the Product Specification Sheets.
There is often more than one way to design, configure and layout an LED lighting application properly to achieve the same lighting effect. Diode LED
strongly recommends that licensed professionals be used in the design and installation of lighting systems that include Diode LED products. The
specifications include important information that a designer and installer should carefully review and strictly follow. Qualified designers and certified
and/or licensed installers, with access to the final installation environment, customer goals, and Diode LED product specifications can make the
requisite decisions appropriate for a successful finished lighting application.
® Toll Free: 877.817.6028 | Fax: 415.592.1596 | www.DiodeLED.com | info@DiodeLED.com
© 2015 Elemental LED, Inc. All rights reserved. Specifications are subject to change without notice.
SPLASHLIGHT® SERIES
5 OF 5
SS112415-3.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising