Cisco | WS-X6848-SFP-2T | Datasheet | Cisco WS-X6848-TX-2T network switch module

Cisco WS-X6848-TX-2T network switch module
Data Sheet
6800 Series 10 Gigabit and Gigabit Ethernet Interface Modules for
Cisco 6500 Series Switches
Product Overview
The Cisco Catalyst® 6500 Series Switches offer a variety of 10 Gigabit and Gigabit Ethernet modules which work in
conjunction with the new Catalyst® 6500 Supervisor Engine 2T/2TXL (VS-S2T-10G & VS-S2T-10GXL) to serve
different needs in the campus and data center for enterprise, commercial, and service provider customers. The
modules in this family include the new 6800 Series 16-port 10 Gigabit Ethernet Fiber Module,16-port 10 Gigabit
Ethernet Copper Module, 48-port Gigabit Ethernet Copper Module, 48-port Gigabit Ethernet Fiber Module and 24port Gigabit Ethernet Fiber Module. The 10 Gigabit Fiber Module supports 10GBASE-CX4, -SR, -LRM, -LX4, -LR, ZR and -ER X2 fiber modules to provide operational distances up to 80 km over single-mode fiber. The 10 Gigabit
Ethernet Copper Module supports RJ-45 connectors and operational distance of up to 55 m over Category 6
Unshielded Twisted Pair (UTP) copper cabling; 100 meters over Category 6 Shielded Twisted Pair (STP) copper
cabling, 100 meters over Category 6A UTP & STP copper cabling, and 100 meters over Category 7 STP copper
cabling. Similarly Gigabit Ethernet Copper Module supports RJ-45 connectors and provides operational distance of
up to 100 meters over Category 5, 5E & 6 UTP copper cabling. The Gigabit Fiber Modules support pluggable optics
and provide operational distances of up to 80 km over single-mode fiber and over multimode fiber.
6800 Series 16-Port 10 Gigabit Ethernet Fiber Module
The 6800 series 16-port 10 Gigabit Ethernet fiber module is suitable for deployment in access and aggregation
network in Campus and Data Center:
●
WS-X6816-10G-2T: 16-port 10 Gigabit Ethernet Fiber Module with DFC4 (Figure 1) and
●
WS-X6816-10G-2TXL: 16-port 10 Gigabit Ethernet Fiber Module DFC4XL (Figure 1)
●
Backplane connection: Connects to the switch fabric using dual full-duplex 20 Gbps switch fabric channels
(40 Gbps total).
●
Chassis/slot support: Can occupy any slot in Cisco Catalyst 6503E, 6504E, 6506E, 6509E, and 6509-V-E.
Can occupy slots 1-6 and 9-13 in a Cisco Catalyst 6513-E.
●
Supervisor engine: Compatible with Supervisor Engine 2T and Supervisor Engine 2TXL
●
Distributed forwarding and performance: Comes equipped with DFC4 or DFC4XL daughter cards,
delivering optimal performance up to a sustained 60 Mpps for L2, IPv4 and MPLS forwarding and 30 Mpps for
IPv6 forwarding.
The 6800 Series 16-port 10 Gigabit Ethernet Fiber module (Figure 1) provides up to 176 10 Gigabit Ethernet Fiber
ports in a single Cisco Catalyst 6513-E Switch chassis, 352 10 Gigabit Ethernet Fiber ports in a Cisco Catalyst 6500
Virtual Switching System (VSS) 2T.
Figure 1.
6800 Series 16-Port 10 Gigabit Ethernet Fiber Module
© 2011-2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 1 of 12
Data Sheet
6800 Series 16-Port 10 Gigabit Ethernet Copper Module
The 6800 series 16-port 10 Gigabit Ethernet Copper module is suitable for Data center access and switch-to-switch
connectivity. The primary use case for 10GBase-T is high-speed server connectivity. Other less common use case
scenarios will leverage 10GBase-T for interconnecting distribution or core switches that reside within a 100m
distance:
●
WS-X6816-10T-2T: 16-port 10 Gigabit Ethernet Copper Module with DFC4 (Figure 1) and
●
WS-X6816-10T-2TXL: 16-port 10 Gigabit Ethernet Copper Module DFC4XL (Figure 1)
●
Backplane connection: Connects to the switch fabric using dual full-duplex 20 Gbps switch fabric channels
(40 Gbps total).
●
Chassis/slot support: Can occupy any slot in Cisco Catalyst 6503E, 6504E, 6506E, 6509E, and 6509-V-E.
Can occupy slots 1-6 and 9-13 in a Cisco Catalyst 6513-E.
●
Supervisor engine: Compatible with Supervisor Engine 2T and Supervisor Engine 2TXL
●
Distributed forwarding and performance: Comes equipped with DFC4 or DFC4XL daughter cards,
delivering optimal performance up to a sustained 60 Mpps for L2, IPv4 and MPLS forwarding and 30 Mpps for
IPv6 forwarding.
The 6800 Series 16-port 10 Gigabit Ethernet Copper module (Figure 1) provides up to 176 10 Gigabit Ethernet
Copper ports in a single Cisco Catalyst 6513-E Switch chassis, 352 10 Gigabit Ethernet Copper ports in a Cisco
Catalyst 6500 Virtual Switching System (VSS) 2T and is primarily designed for data center access with a secondary
use case for switch-to-switch connectivity.
Figure 2.
6800 Series 16-Port 10 Gigabit Ethernet Copper Module
6800 Series 10 Gigabit Ethernet Module Features
For more information, see the white paper discussing 10 Gigabit Ethernet switching for enterprises at
http://www.cisco.com/en/US/products/hw/switches/ps708/products_white_paper0900aecd802a648b.shtml.
Main Features and Benefits
The 6800 Series 16-port 10 Gigabit Ethernet Fiber and Copper Module supports IEEE 802.3ad link aggregation and
Cisco® distributed EtherChannel technology for fault-tolerant connectivity and bandwidth scalability of up to 80 Gbps
per EtherChannel connection using any 8 ports in the same chassis. In addition, it supports hardware-based multicast
replication, quality of service (QoS), access control lists (ACLs), jumbo frames, and low latency to enable secure and
predictable performance for bandwidth-intensive applications. It consists of 4 port groups of 4 ports each. Users can
operate each port group in either oversubscription mode (up to 4 ports used per port group) or performance mode (1
port used per port group), providing the flexibility to use some ports for connection to servers and other ports for
interconnection of switches.
© 2011-2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 2 of 12
Data Sheet
Table 1 summarizes the primary features and benefits of the 6800 Series 10 Gigabit Ethernet modules.
Table 1.
6800 Series 10 Gigabit Ethernet Module Primary Features
Feature
16-port 10GbE Fiber Module
16-Port 10GbE Copper Module
Ports
16
16
Optics
X2
Copper (RJ-45) connectors
Switch fabric
connection
2 x 20 Gbps (40 Gbps total)
2 x 20 Gbps (40 Gbps total)
Oversubscription
4:1 16 ports (oversubscription mode)
4:1 16 ports (oversubscription mode)
1:1 4 ports (performance mode)
1:1 4 ports (performance mode)
Forwarding engine
Queues
● WS-X6816-10G-2T: comes equipped with DFC4 for
distributed forwarding, supporting 256K forwarding
entries, increased ACL entries to 64K, increased
Netflow entries to 512K and increased IPv4 forwarding
speed to 60 Mpps
● WS-X6816-10G-2TXL: equipped with DFC4XL for
distributed forwarding, supporting 1 million forwarding
entries, increased ACL entries to 256K, increased
Netflow entries to 1024K and increased IPv4 forwarding
speed to 60 Mpps
● Increased performance of up to 60Mpps for L2, IPv4
and MPLS forwarding and up to 30Mpps for IPv6
forwarding
● Support for 16K Bridge Domains, allowing the standard
4K VLANs to be reused across these bridge domains,
effectively increasing the number of VLANs available in
the system
● Increased MAC Address Table to 128K
● WS-X6816-10T-2T: comes equipped with DFC4 for
distributed forwarding, supporting 256K forwarding
entries, increased ACL entries to 64K, increased
Netflow entries to 512K and increased IPv4 forwarding
speed to 60 Mpps
● WS-X6816-10T-2TXL: equipped with DFC4XL for
distributed forwarding, supporting 1 million forwarding
entries, increased ACL entries to 256K, increased
Netflow entries to 1024K and increased IPv4 forwarding
speed to 60 Mpps
● Increased performance of up to 60Mpps for L2, IPv4
and MPLS forwarding and up to 30Mpps for IPv6
forwarding
● Support for 16K Bridge Domains, allowing the standard
4K VLANs to be reused across these bridge domains,
effectively increasing the number of VLANs available in
the system
● Increased MAC Address Table to 128K
● Increased multicast routes to 256K
● IGMPv3 snooping in hardware
● Increased multicast routes to 256K
● IGMPv3 snooping in hardware
● PIM registers in hardware
● IPv6 MLDv2 snooping in hardware
● PIM registers in hardware
● IPv6 MLDv2 snooping in hardware
● IPV4 & IPv6 in IPv6 tunnelling
● IPv6 in IPv4 tunneling ISATAP, 6to4, GRE)
● IPV4 & IPv6 in IPv6 tunnelling
● IPv6 in IPv4 tunneling ISATAP, 6to4, GRE)
● QoS support for uniform, short pipe and pipe mode
tunnel
● Terminate the tunnel in the same loopback
● QoS support for uniform, short pipe and pipe mode
tunnel
● Terminate the tunnel in the same loopback
Oversubscription mode:
● Receive: 1p7q2t per port
● Transmit: 1p7q4t per port group
Performance mode:
● Receive: 8q4t per port
Queuing mechanisms
Scheduler
● Transmit: 1p7q4t per port
● Class of Service (CoS) based queue mapping
● (Differentiated Service Code Point (DSCP) based
queue mapping
● Class of Service (CoS) based queue mapping
● (Differentiated Service Code Point (DSCP) based
queue mapping
Oversubscription mode:
● Deficit Weighted Round Robin (DWRR)
● Weighted Random Early Detection (WRED)
● WRED
● Shaped Round Robin (SRR) at egress
Hardware-based
multicast replication
● Transmit: 1p7q4t per port group
Performance mode:
● Receive: 8q4t per port
● Transmit: 1p7q4t per port
Performance mode:
● DWRR
Port buffers
Oversubscription mode:
● Receive: 1p7q2t per port
Oversubscription mode:
● Deficit Weighted Round Robin (DWRR)
● Weighted Random Early Detection (WRED)
Performance mode:
● DWRR
● WRED
● Shaped Round Robin (SRR) at egress
Oversubscription mode:
● 90 MB per port group
Oversubscription mode:
● 90 MB per port group
Performance mode:
● 256 MB per port (128 MB for ingress and 128 MB for
egress)
Performance mode:
● 256 MB per port (128 MB for ingress and 128 MB for
egress)
● Ingress and Egress replication-mode
● Approximately 20 Gbps per replication engine
● Ingress and Egress replication-mode
● Approximately 20 Gbps per replication engine
● 2 replication engines per module
● 2 replication engines per module
© 2011-2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 3 of 12
Data Sheet
Feature
16-port 10GbE Fiber Module
16-Port 10GbE Copper Module
Jumbo frame support
for bridged and routed
packets
Up to 9216 bytes
Up to 9216 bytes
Maximum port density
per chassis
176 ports (6513-E chassis)
176 ports (6513-E chassis)
128 ports (6509-E chassis)
128 ports (6509-E chassis)
Maximum port density
per VSS
352 ports
352 ports
Can be used to form
virtual switch link
● Performance mode: Yes
● Performance mode: Yes
◦ Up to 4 10 Gigabit Ethernet ports can be used for
virtual switch link
virtual switch link
● Oversubscription mode: No
● Oversubscription mode: No
Supervisor engines
supported
◦ Up to 4 10 Gigabit Ethernet ports can be used for
Catalyst® 6500 Supervisor Engine 2T and 2TXL
Catalyst® 6500 Supervisor Engine 2T and 2TXL
Chassis supported
● Any Cisco Catalyst 6500 E-Series chassis, including
6503-E, 6504-E, 6506-E, 6509-E, 6509-V-E (NEBS
compliant) and 6513-E chassis
● Not supported in non-E Series chassis
● Any Cisco Catalyst 6500 E-Series chassis, including
6503-E, 6504-E, 6506-E, 6509-E, 6509-V-E (NEBS
compliant) and 6513-E chassis
● Not supported in non-E Series chassis
Slot requirements
● Can occupy any slot in any Cisco Catalyst 6503-E,
6504-E, 6506-E, 6509-E or 6509-V-E or chassis
● Can occupy slots 1-6 and 9-13 in a Cisco Catalyst
6513-E chassis
● Can occupy any slot in any Cisco Catalyst 6503-E,
6504-E, 6506-E, 6509-E or 6509-V-E or chassis
● Can occupy slots 1-6 and 9-13 in a Cisco Catalyst
6513-E chassis
Onboard memory
1 GB default
1 GB default
Cabling Supported
10GBASE-CX4, -SR, -LRM, -LX4, -LR, -ZR and -ER X2
fiber modules and 10GBASE-T
Category 6, 6A UTP & STP & Category 7 STP copper
cabling
Table 2 summarizes pluggable optics supported on the Cisco Catalyst 6500 Series 10 Gigabit Ethernet modules.
Table 2.
Pluggable Optics for 6800 Series 10 Gigabit Ethernet Modules
X2 Part Number
Transceiver Type
Wavelength
IEEE Standard
Maximum Distance and Cable Type
X2-10GB-LRM
10GBASE-LRM
1310 nm serial
IEEE 802.3aq
220m over multimode fiber
X2-10GB-SR
10GBASE-SR
850 nm serial
IEEE 802.3ae
X2-10GB-LR
10GBASE-LR
1310 nm serial
IEEE 802.3ae
10 km over single-mode fiber
X2-10GB-ER
10GBASE-ER
1550 nm serial
IEEE 802.3ae
40 km over single-mode fiber
X2-10GB-LX4
10GBASE-LX4
WWDM 1310 nm
IEEE 802.3ae
● 300m over 62.5-micron FDDI grade
multimode fiber
● 240m over 50-micron 400 MHz x km
multimode fiber
● 300m over 50-micron 500 MHz x km
multimode fiber
X2-10GB-CX4
10GBASE-CX4
Copper
IEEE 802.3ak
15m over 8 pair 100-Ohm InfiniBand cable
X2-10GB-ZR
10GBASE-ZR
1550 nm serial
-
80 km over single-mode fiber
X2-10G-DWDM
DWDM
32 different
wavelengths; C band
100 GHz ITU grid
32 wavelengths over single strand of singlemode fiber; 80 km
X2-10GB-T
10GBASE-T
Copper
IEEE 802.3an
100m over CAT6A/CAT7 (copper)
CVR-X2-SFP10G
SFP+ converter for
X2 ports
© 2011-2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
● 26m over 62.5-micron FDDI-grade
multimode fiber
● 33m over 62.5-micron 200 MHz x km
multimode fiber
● 66m over 50-micron 400 MHz x km
multimode fiber
● 82m over 50-micron 500 MHz x km
multimode fiber
● 300m over 50-micron 2000 MHz x km
multimode fiber
Page 4 of 12
Data Sheet
X2 Part Number
Transceiver Type
Wavelength
IEEE Standard
Maximum Distance and Cable Type
SFP-H10GB-CU1M1
Cisco 10GBASE-CU
SFP+ cable
Copper
SFP+ MSA SFF-8431
1-m 10G SFP+ Twinax cable assembly,
passive
Cisco 10GBASE-CU
SFP+ cable
Copper
SFP+ MSA SFF-8431
3-m 10G SFP+ Twinax cable assembly,
passive
Cisco 10GBASE-CU
SFP+ cable
Copper
SFP+ MSA SFF-8431
5-m 10G SFP+ Twinax cable assembly,
passive
10GBASE-SR SFP+
transceiver module
850nm MMF
IEEE 802.3ae
● 26m over 62.5-micron FDDI-grade
multimode fiber
● 33m over 62.5-micron 200 MHz x km
multimode fiber
● 66m over 50-micron 400 MHz x km
multimode fiber
● 82m over 50-micron 500 MHz x km
multimode fiber
● 300m over 50-micron 2000 MHz x km
multimode fiber
IEEE 802.3aq
● 220m on standard Fiber Distributed Data
Interface (FDDI) grade MMF
(With CVR-X2-SFP10G
converter for X2 ports)
SFP-H10GB-CU3M1
(With CVR-X2-SFP10G
converter for X2 ports)
SFP-H10GB-CU5M1
(With CVR-X2-SFP10G
converter for X2 ports)
SFP-10G-SR
(With CVR-X2-SFP10G
converter for X2 ports)
SFP-10G-LRM
(With CVR-X2-SFP10G
10GBASE-LRM SFP+ 1310 nm MMF and
transceiver module
SMF
converter for X2 ports)
Product Specifications
Table 3 lists product specification of the 6800 Series 10 Gigabit Ethernet modules.
Table 3.
Product Specifications
Product
Specifications
Standard protocols
IEEE 802.1d, IEEE 802.1p, IEEE 802.1q, IEEE 802.1s, IEEE 802.1w, IEEE 802.3x, IEEE 802.3ad,
IEEE 802.3ae, IEEE 802.3ak, IEEE 802.3aq, and IEEE 802.3an
Physical specifications
● Occupies one slot in the Cisco Catalyst 6500 E-Series chassis
● Dimensions (H x W x D): 1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm)
● Weight:
◦ WS-X6816-10G-2T & 2TXL, WS-X6816-10T-2T & 2TXL: 13.6 pounds excluding X2 components; ¼ pound
for each X2
Environmental conditions
Operating temperature:
● Agency-certified for operation: 32 to 104°F (0 to 40°C)
● Design and tested for operation 32 to 130°F (0 to 55°C)
● Storage temperature: -40 to 167°F (-40 to 75°C)
● Relative humidity: 10 to 90 percent, noncondensing
Operating altitude:
● Agency-certified for operation: -500 to 6500 ft (-150 to 2000m)
● Designed and tested for operation -500 to 10000 ft (-150 to 3000m)
Regulatory compliance
6800 Series 10 Gigabit Ethernet Copper module, when installed in a system, comply with the following EMC and
safety standards:
EMC Standards:
● FCC Part 15 (CFR 47) Class A
● ICES-003 Class A
● VCCI Class A
● EN55022 Class A
● EN55024
● CISPR24
● CISPR 22 Class A
● AS/NZS CISPR 22 Class A
● ETS 300 386
● KN 22 Class A
● EN 50082-1
© 2011-2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 5 of 12
Data Sheet
Product
Specifications
● EN61000-3-2
● EN61000-3-3
● EN61000-6-1
● CNS13438 Class A
● KN6100 -4 Series
Safety Standards:
● UL 60950-1
● CAN/CSA C22.2 No. 60950
● EN 60950-1
● IEC 60950-1
● AS/NZS 60950-1
● IEC 60825 Class 1
● EN 60825 Class 1
● 21CFR 1040
NEBS criteria levels
SR-3580 Issue 3, June 2007 (GR-63-CORE, issue 3, and GR-1089-CORE, issue 4)
● ETS 300 019-2-1, Class 1.1 Storage
● ETS 300 019-2-2, Class 2.1 and 2.2 Transportation
ETSI
● ETS 300 019-2-3, Class 3.1E Stationary Use
Network management
● ETHERLIKE-MIB (RFC 1643)
● IF-MIB (RFC 1573)
● Bridge MIB (RFC 1493)
● CISCO-STACK-MIB
● CISCO-VTP-MIB
● CISCO-CDP-MIB
● RMON MIB (RFC 1757)
● CISCO-PAGP-MIB
● CISCO-STP-EXTENSIONS-MIB
● CISCO-VLAN-BRIDGE-MIB
● CISCO-VLAN-MEMBERSHIP-MIB
● ENTITY-MIB (RFC 2037)
● HC-RMON
● RFC1213-MIB (MIB-II)
● SMON-MIB
Power requirements
● WS-X6816-10G-2T: 488.5 Watts
● WS-X6816-10G-2TXL: 503.5 Watts
● WS-X6816-10T-2T: 514.96 Watts
● WS-X6816-10T-2TXL: 529.96 Watts
● Go to http://www.cisco.com/go/powercalculator for easy power consumption calculation.
Indicators
● Status: green (operational), red (faulty), and orange (module booting)
● Link: green (port enabled and connected), orange (port disabled), and off (port enabled and not connected)
6800 Series Gigabit Ethernet Fiber & Copper Modules
Designed for high performance Enterprise and Service Provider distribution, core layers, data-center, Web-hosting
and Metro Ethernet applications, 6800 Series Fiber and Copper media interface modules provide Gigabit Ethernet
forwarding using fiber optic or twisted pair cabling.
There are 3 different 1G modules which are supported with new Supervisor 2T and 2TXL:
●
WS-X6824-SFP-2T and WS-X6824-SFP-2TXL: 24-port SFP fiber Gigabit Ethernet Module with DFC4 and
DFC4XL (Figure 3)
●
WS-X6848-SFP-2T and WS-X68248-SFP-2TXL: 48-port SFP fiber Gigabit Ethernet Module with DFC4 and
DFC4XL (Figure 4)
●
WS-X6848-TX-2T and WS-X6848-TX-2TXL: 48-port Copper Gigabit Ethernet Module with DFC4 and DFC4XL
(Figure 5)
© 2011-2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 6 of 12
Data Sheet
●
Backplane connection: Connects to the switch fabric using dual full-duplex 20 Gbps switch fabric channels
(40 Gbps total). The 6824 connects to the switch fabric using a single full-duplex 20Gbps switch fabric
channel.
●
Chassis/slot support: Can occupy any slot in Cisco Catalyst 6503E, 6504E, 6506E, 6509E, and 6509-V-E.
Can occupy slots 1-6 and 9-13 in a Cisco Catalyst 6513-E.
●
Supervisor engine: Compatible with Supervisor Engine 2T and Supervisor Engine 2TXL
●
Distributed forwarding and performance: Come equipped with DFC4 or DFC4XL daughter cards, delivering
optimal performance up to a sustained 60 Mpps for L2, IPv4 and MPLS forwarding and 30 Mpps for IPv6
forwarding.
Figure 3.
6800 Series 24-Port Gigabit Ethernet Interface Module WS-X6824-SFP-2T/2TXL
Figure 4.
6800 Series 48-Port Gigabit Ethernet Interface Module WS-X6848-SFP-2T/2TXL
Figure 5.
6800 Series 48-Port 10/100/1000 Interface Copper Module WS-X6848-TX-2T/2TXL
Main Features and Benefits
Table 4 summarizes the primary features and benefits of the 6800 Series Gigabit Ethernet Fiber and Copper modules
Table 4.
6800 Series Gigabit Ethernet Fiber and Copper Modules Primary Features
Product
Transceiver
Type
Ports/Interface/
Connectors
WSX6848GE-TX
RJ-45
48-port, RJ-45, 100m,
Category 5 cable
WSX6848SFP
Small Formfactor
Pluggable
(SFP)
48 port; 1000BASE-SX,
LX/LH, -ZX, -T;
1000BASE-CWDM;
LC connecter
Port Density/
Chassis Model
Maximum
Frame Size
Queues per
Port (Tx =
Transmit,
Rx =
Receive),**
● 528 ports/6513E
● 384 ports/6509E
Up to 9216
bytes/frame
● Tx1p3q8t;
Rx-2q8t
DWRR
● Rx166KB
● Tx1.17MB
1GB Default
● 528 ports/6513E
● 384 ports/6509E
Up to 9216
bytes/frame
● Tx1p3q8T
● Rx-2q8T
Deficit
Weighted
Round
Robin
(DWRR)
● Rx166KB
● Tx1.17MB
1GB Default
© 2011-2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Scheduler
Buffer Size
per Port
Onboard
Memory
Page 7 of 12
Data Sheet
WSX6824SFP
**
Small Formfactor
Pluggable
(SFP)
24-port; 1000BASESX, LX/LH, -ZX, -T;
1000BASE-CWDM;
LC connecter
● 264 ports/6513E
● 192 ports/6509E
Up to 9216
bytes/frame
● Tx1p3q8T
● Rx-2q8T
DWRR
● Rx166KB
● Tx1.17MB
1GB Default
Queues Legend: 1p3q1t = 1 priority queue, 3 round robin queues, 1 threshold
Interface Distances
Table 5 summarizes the interfaces and distances supported by the 6800 Series Gigabit Ethernet Fiber modules
Table 5.
6800 Gigabit Ethernet Fiber Modules Supported Interfaces & Distances
Module
SFP
Wavelength (nm)
Fiber/Cable Type
WS-X6848-SFP
1000BASE-SX
850
MMF
CoreSize (micron) Model Bandwidth
(MHz/km)
WS-X6824-SFP
WS-X6848-SFP
1000BASE-LX/LH
● MMF*
● SMF
1300
WS-X6824-SFP
WS-X6848-SFP
● 62.5
● 62.5
● 160
● 200
● 220m (722 ft)
● 275m (902 ft)
● 50.0
● 50.0
● 400
● 500
● 500m (1640 ft)
● 550m (1804 ft)
● 62.5
● 50.0
● 500
● 400
● 550 m (1804 ft)
● 550 m (1804 ft)
● 50.0
● 9/10
● 500
● 550 m (1804 ft)
● 10 km
(32,810 ft)
1000BASE-ZX
1550
SMF
9/10
-
43.4 to 62 miles
(70 to 100 km)**
1000BASE-T
-
Category 5
-
-
100 m (328 ft)
WS-X6824-SFP
WS-X6848-SFP
Cable Distance
WS-X6824-SFP
Product Specifications
Table 6 lists product specification of the 6800 Series Gigabit Ethernet Fiber and Copper Modules
Table 6.
Product Specifications
Product
Specifications
Standard protocols
● IEEE 802.1d, IEEE 802.1p, IEEE 802.1q, IEEE 802.1s, IEEE 802.1w, IEEE 802.3x, IEEE 802.3z, IEEE 802.3ab,
and IEEE 802.3ad,
● 1000BASE-T, 1000BASE-X (GBIC), 1000BASE-SX, 1000BASE-LX/LH, 1000BASE-ZX, CWDM
Physical specifications
● Occupies one slot in the Cisco Catalyst 6500 E-Series chassis
● Dimensions (H x W x D): 1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm)
Environmental conditions
Operating temperature:
● Operating temperature: 32 to 104°F (0 to 40°C)
● Storage temperature: -40 to 167°F (-40 to 75°C)
● Relative humidity 10 to 90% non condensing
Operating altitude:
● Agency-certified for operation: -500 to 6500 ft (-150 to 2000m)
● Designed and tested for operation -500 to 10000 ft (-150 to 3000m)
NEBS criteria levels
ETSI
SR-3580 Issue 3, June 2007 (GR-63-CORE, issue 3, and GR-1089-CORE, issue 4)
● ETS 300 019-2-1, Class 1.1 Storage
● ETS 300 019-2-2, Class 2.1 and 2.2 Transportation
● ETS 300 019-2-3, Class 3.1E Stationary Use
Network management
● ETHERLIKE-MIB (RFC 1643)
● IF-MIB (RFC 1573)
● Bridge MIB (RFC 1493)
● CISCO-STACK-MIB
● CISCO-VTP-MIB
● CISCO-CDP-MIB
● RMON MIB (RFC 1757)
● CISCO-PAGP-MIB
© 2011-2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 8 of 12
Data Sheet
Product
Specifications
● CISCO-STP-EXTENSIONS-MIB
● CISCO-VLAN-BRIDGE-MIB
● CISCO-VLAN-MEMBERSHIP-MIB
● ENTITY-MIB (RFC 2037)
● HC-RMON
● RFC1213-MIB (MIB-II)
● SMON-MIB
Power Requirements
● WS-X6824-SFP-2T and WS-X6824-SFP-2TXL: 204.66 and 209.66 Watts respectively
● WS-X6848-SFP-2T and WS-X6848-SFP-2TXL: 334.44 and 339.44 Watts respectively
● WS-X6848-TX-2T and WS-X6848-TX-2TXL: 405 and 410 Watts respectively
● Go to http://www.cisco.com/go/powercalculator for easy power consumption calculation.
● Status: green (operational), red (faulty), and orange (module booting)
● Link: green (port enabled and connected), orange (port disabled), and off (port enabled and not connected)
Indicators
Ordering Information
Table 7 gives ordering information.
Table 7.
Part Numbers for Ordering
Part Numbers
Description
6800 Series 10 Gigabit Fiber, Copper, Gigabit Fiber and Gigabit Copper Modules
WS-X6816-10T-2T & 2TXL
6800 Series 16-Port 10 Gigabit Ethernet Copper Module with DFC4 & DFC4XL
WS-X6816-10G-2T & 2TXL
6800 Series 16-Port 10 Gigabit Ethernet Fiber Module with DFC4 & DFC4XL
WS-X6824-SFP-2T & 2TXL
6800 Series 24-Port 1 Gigabit SFP Fiber Ethernet Module with DFC4 & DFC4XL
WS-X6848-SFP-2T & 2TXL
6800 Series 48-Port 1 Gigabit SFP Fiber Ethernet Module with DFC4 & DFC4XL
WS-X6848-TX-2T & 2TXL
6800 Series 48-Port 1 Gigabit Copper Ethernet Module with DFC4 & DFC4XL
WS-F6K-DFC4-EXL=
Cisco Catalyst 6500 Dist Fwd Card- DFC4XL Spare for WS-X6816-10G-2T & WS-X6816-10T-2T
WS-F6K-DFC4-AXL=
Cisco Catalyst 6500 Dist Fwd Card- DFC4XL Spare for WS-X6824-SFP-2T, WS-X6848-SFP-2T and WS-X6848-TX2T
X2 Optics
X2-10GB-LRM
10GBASE-LRM X2 (multimode fiber)
X2-10GB-SR
10GBASE-SR X2 (multimode fiber)
X2-10GB-LR
10GBASE-LR X2 (single-mode fiber)
X2-10GB-ER
10GBASE-ER X2 (single-mode fiber)
X2-10GB-ZR
10GBASE-ZR X2 (single-mode fiber)
X2-10GB-LX4
10GBASE-LX4 X2 (multimode fiber)
X2-10GB-CX4
10GBASE-CX4 X2 (copper InfiniBand cable)
X2-10G-DWDM
32 wavelengths over single strand of single-mode fiber; 80 km
CVR-X2-SFP10G
SFP+ converter for X2 ports
SFP-10G-SR
10GBASE-SR SFP+ transceiver module
SFP-10G-LR
10GBASE-LR SFP+ transceiver module
SFP-H10GB-CU1M1
1-m 10G SFP+ Twinax cable assembly, passive
SFP-H10GB-CU3M1
3-m 10G SFP+ Twinax cable assembly, passive
SFP-H10GB-CU5M1
5-m 10G SFP+ Twinax cable assembly, passive
SFP
GLC-SX-MM
1000BASE-SX SFP (multimode only) Dual LC connector
GLC-ZX-SM
1000BASE-ZX SFP (single mode only) Dual LC connector
GLC-LH-SM
1000BASE-LX SFP (single mode only) Dual LC connector
GLC-T
1000BASE-T SFP (copper twisted pair) RJ-45 connector
CWDM-SFP-1470=*
Cisco CWDM SFP 1470 nm; Gigabit Ethernet and 1G/2G FC
© 2011-2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 9 of 12
Data Sheet
Note:
●
6800 Series 16-port 10 Gigabit Ethernet fiber module:
◦ WS-X6816-10G-2T ships with WS-X6816-10G and WS-F6K-DFC4-E.
◦ WS-X6816-10G-2TXL ships with WS-X6816-10G and WS-F6K-DFC4-EXL.
◦ The front panel of these modules is labeled
WS-X6816-10G-2T or
WS-X6816-10G-2TXL if it is XL version.
◦ Cisco IOS® Software commands display WS-X6816-10G with either WS-F6K-DFC4-E or WS-F6K-DFC4EXL.
●
6800 Series 16-port 10 Gigabit Ethernet copper module:
◦ WS-X6816-10T-2T ships with WS-X6816-10T and WS-F6K-DFC4-E.
◦ WS-X6816-10T-2TXL ships with WS-X6816-10T and WS-F6K-DFC4-EXL.
◦ The front panel of these modules is labeled
WS-X6816-10T-2T or
WS-X6816-10T-2TXL if it is XL version.
◦ Cisco IOS® Software commands display WS-X6816-10T with either WS-F6K-DFC4-E or WS-F6K-DFC4EXL.
●
6800 Series Gigabit Ethernet fiber and copper modules:
◦ WS-X6824-SFP-2T ships with WS-X6824-SFP and WS-F6K-DFC4-E.
◦ WS-X6824-SFP-2TXL ships with WS-X6824-SFP and WS-F6K-DFC4-EXL.
◦ The front panel of these modules is labeled
WS-X6824-SFP-2T or
WS-X6824-SFP-2TXL if it is XL version.
◦ Cisco IOS® Software commands display WS-X6824-SFP with either WS-F6K-DFC4-E or WS-F6K-DFC4EXL.
◦ WS-X6848-SFP-2T ships with WS-X6848-SFP and WS-F6K-DFC4-E.
◦ WS-X6848-SFP-2TXL ships with WS-X6848-SFP and WS-F6K-DFC4-EXL.
◦ The front panel of these modules is labeled WS-X6824-SFP.
◦ Cisco IOS® Software commands display WS-X6848-SFP with either WS-F6K-DFC4-E or WS-F6K-DFC4EXL.
◦ WS-X6848-TX-2T ships with WS-X6848-TX and WS-F6K-DFC4-E.
◦ WS-X6848-TX-2TXL ships with WS-X6824-SFP and WS-F6K-DFC4-EXL.
◦ The front panel of these modules is labeled
WS-X6848-TX-2T or
WS-X6848-TX-2TXL if it is XL version.
◦ Cisco IOS® Software commands display WS-X6848-TX with either WS-F6K-DFC4-E or WS-F6K-DFC4EXL.
© 2011-2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 10 of 12
Data Sheet
Cisco and Partner Services
Enable the innovative, secure, intelligent edge in the Borderless Network Architecture using personalized services
from Cisco and our partners. Through a discovery process that begins with understanding your business objectives,
we help you integrate the new Cisco Catalyst 6500-C4 System into your architecture and incorporate network
services onto that platform. Sharing knowledge and leading practices, we support your success every step of the way
as you deploy, absorb, manage, and scale new technology. Choose from a flexible suite of support services designed
to meet your business needs and help you maintain high-quality network performance while controlling operational
costs. For additional information about Cisco services, visit http://www.cisco.com/go/services.
Warranty Coverage and Technical Service Options
The Cisco Catalyst 6500 C4 System comes with a Cisco 90-day hardware warranty. Adding a contract for a technical
service offering such as Cisco SMARTnet® Service to your device coverage provides access to the Cisco Technical
Assistance Center (TAC) and can provide a variety of hardware replacement options to meet critical business needs,
updates for licensed OS software, and registered access to the extensive Cisco.com knowledge base and support
tools.
For more information about Cisco warranties, go to http://www.cisco.com/go/warranty.
For information about Cisco Technical Services, go to http://www.cisco.com/go/ts.
Table 8 shows the Cisco technical services available for the Cisco Catalyst 6500 C4 System.
Table 8.
Cisco Technical Services for Cisco Catalyst 6500 C4 System
Technical Services
Cisco SMARTnet Service
● Around-the-clock, global access to the Cisco Technical Assistance Center (TAC)
● Unrestricted access to the extensive Cisco.com resources, communities, and tools
● Next-business-day, 8x5x4, 24x7x4, and 24x7x2 advance hardware replacement2 and onsite parts replacement and installation available
● Ongoing operating system software updates within the licensed feature set1
● Proactive diagnostics and real-time alerts on Smart Call Home enabled devices
Cisco Focused Technical Support Services
3 levels of premium, high-touch services are available:
● Cisco High-Touch Operations Management Service
● Cisco High-Touch Technical Support Service
● Cisco High-Touch Engineering Service
Valid Cisco SMARTnet or SP Base contracts on all network equipment are required.
Footnotes:
1
. Cisco operating system updates include the following: maintenance releases, minor updates, and major updates within the
licensed feature set.
2
. Advance hardware replacement is available in various service-level combinations. For example, 8x5xNBD indicates that shipment
will be initiated during the standard 8-hour business day, 5 days a week (the generally accepted business days within the relevant
region), with next business day (NBD) delivery. Where NBD is not available, same day ship is provided. Restrictions apply; please
review the appropriate service descriptions for details.
For More Information
For more information about Cisco Catalyst 6500 Series Switches, visit
http://www.cisco.com/en/US/products/hw/switches/ps708/index.html or contact your local account representative.
© 2011-2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 11 of 12
Data Sheet
Printed in USA
© 2011-2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
C78-451794-04
03/13
Page 12 of 12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising