es c Ac ies r so Accessories Mounting and Connection Sockets DIN Rail or Surface Mount Sockets 8 Pin Octal Socket (600 VAC) P/N: OT08PC 8 pin 35 mm DIN rail or surface mount socket. OT08PC is rated at 10 A at 600 V AC and has pressure clamp terminals. Select this socket for use with plug in three phase voltage monitors. For use with AWG 12 to 22 (3.2 to 0.33 mm2) wire sizes. Hold-down clips not available. Dimensions: 1.60 W x 2.1 l x .97 h in. (40.6 x 53.3 x 24.6 mm) 8 Pin Octal Socket (300 VAC) 7 P/N: NDS-8 May be surface mounted with two #6 (M 3.5 x 0.6) screws or snaps onto a 35 mm DIN rail. A spring mechanism allows easy removal. Screw terminals with captive wire clamps accept up to two #14 AWG (2.45 mm2) wires. Rated 10 A at 300 V AC. Uses PSC8 hold-down clips. Dimensions: 1.60 W x 2.03 x .85 h in. (40.6 x 51.6 x 21.6 mm) 11 Pin Magnal Socket P/N: NDS-11 May be surface mounted with two #6 (M 3.5 x 0.6) screws or snaps onto a 35 mm DIN rail. A spring mechanism allows easy removal. Screw terminals with captive wire clamps accept up to two #14 AWG (2.45 mm2) wires. Rated 10 A at 300 V AC. Uses PSC11 hold-down clips. Dimensions: 1.80 W x 2.03 x 1.25 h in. (45.7 x 51.6 x 31.8 mm) Hold-Down Clips P/N: PSC8 PSC11 Securely mounts plug in controls in any position. Also provides protection against vibration. Select the PSC8 for use with NDS-8 or the PSC11 for use with NDS-11 sockets. Comes in sets of two. P/N: P1011-6 8 pin surface mount socket with binder head screw terminals. Rated 10 A at 600V AC. Select this socket for use with plug in three phase voltage monitors. When used with TDM, TDB, TDS Series timers the combination is UL Listed. Uses PSCRB8 hold-down brackets. Hold-Down Brackets P/N: PSCRB8 Designed for use with P1011-6 socket. Securely mounts 8 pin plug-in controls in any position, and provides protection against vibration. Comes in sets of two. Dimensions: 2.0 W x 2.25 x .63 h in. (50.8 x 57.2 x 15.9 mm) 7.38 1SXU000023C0202 Low Voltage Products & Systems ABB Inc. • Sales Sales & Technical Information 1-888-385-1221 8AM to 5PM CST - Product Information www.ssac.com/pp1.htm Socketpp 8 Pin Octal Socket (600 VAC) 01.07.08 Surface Mount Sockets Ac Accessories Mounting Methods, Timer Adjustments and Dials ce ss or ies Front Panel Mount Kit P/N: BZ1 Provides an easy method of through-the-panel mounting of 8 or 11 pin plug-in timers, flashers, and other controls. May be mounted in panels up to 0.125 in. (3.2 mm) thick. Includes two clamps and two screws. Inches (Millimeters) Illustrates panel opening size required to mount BZ1. 2 (5 .0 0. 8) ← (25 ← ← 1.0 ) ← Allows any 2 x 2 in. (50.8 x 50.8 mm) or 2 x 3 in. (50.8 x 76.2 mm) module to be mounted on a 35 mm DIN type rail. Comes complete with mounting hardware for 0.75 in. (19 mm) and 1 in. (25.4 mm) thick modules. 7 0.8 ← P/N: P1023-20 ← (52.0 ← DIN Rail Mount Adaptor .4) ←1 ← .25 (31 .8) Mounting hole for #8 (M4 X 0.7) bolt Inches (Millimeters) P/N: P1004-95-X Versa-Pot Panel mountable, industrial potentiometer recommended for remote time delay adjustment. The shaft is slotted for screwdriver adjustment and serrated for slip-proof finger adjustment. Accepts Versa-Knob or Lock Shaft. May be ordered with two 8 in. (20.3 cm) wires soldered to pot (clockwise increase) and female quick connect terminals on other ends by adding suffix -X to end of part number. P/N: P1004-95 Ordering Table Part Number Value (Ohms) With Wire Leads P1004-95 P1004-95-X 100 K No Yes Technical Data Rating Taper Shaft Rotation Tolerance 0.25W at 55°C Linear 300° +/-5° +/-10% Inches (Millimeters) Versa-Knob Mountspp P/N: P0700-7 Versa-Knob is designed for 0.25 in (6.35 mm) shaft of Versa-Pot or Q-Pot. Semi-Gloss industrial black finish. 01.17.08 Time Adjustment Dials Dials for use with remote Versa-Pot. Reverse screen printed on clear plastic to avoid damage to printed image. Ordering Table Part Number Range Increments P0400-82 P0400-26 P0400-27 0.1 ... 10s 0.1 ... 10m 0 ...10 1s 1m Reference Dial Low Voltage Products & Systems ABB Inc. • Sales Sales & Technical Information 1-888-385-1221 8AM to 5PM CST - Product Information www.ssac.com/pp1.htm SS = Set Screw Inches (Millimeters) 7.39 1SXU000023C0202 es c Ac Accessories Liquid Level Probes and Probe Holders ies r so Liquid Level Control Electrodes Designed for use with all conductive liquid level controls. Composed of insulators and metal parts made of number 300 series stainless steel. These internally conductive probe holders are designed for a maximum steam pressure of 240 PSI. Ordering Table Part Number Description PHST-38QTN Probe Holder (UL Recognized) P0700-409 Protective Boot 7 Inches (Millimeters) Inches (Millimeters) Liquid Level Probe Inches (Millimeters) P/N: LLP-24 Threaded stainless steel probe measuring 24 in. (61 cm) long. Designed for use with WCC-1138 and WCC-1138-3 liquid level control electrodes. Suspension Electrode Steel electrode (X 12 CR Mo S 17) with sleeve (Lupulen 6011 L) suitable up to 60°C max. Attaches to an insulated wire suspended from the top of the holding tank. Length of wire determines the sensing location. Ordering Table Part Number Units per pack Weight (kg/oz) 1SVR 402 902 R 0000 1 0.053/1.855 FH3P does not include P0600-11 fuses 7.40 1SXU000023C0202 3.0 (78 7 ) → 2 (52 .07 → .5) ← ← 2.32 (59) Fast acting fuse for use with voltage monitors. Rated 2 A at 500 V AC. 1.5 x .41 in. (38.1 x 10.4 mm) ←→ Midget Fuse Ordering Table Part Number Description FH3P 3 Pole Fuse Block P0600-11 Midget Fuse Low Voltage Products & Systems ABB Inc. • Sales Sales & Technical Information 1-888-385-1221 8AM to 5PM CST - Product Information www.ssac.com/pp1.htm LLCACCpp 01.04.08 Three Phase Fuse Block/Disconnect Three phase fuse block disconnect designed for use with HRC midget fuses rated up to 25 A at 500 V AC. Snap onto 35mm DIN rail.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project