Annexure - I TECHNICAL BID - COMPLIANCE

Annexure - I TECHNICAL BID - COMPLIANCE
Annexure - I
A
Sr No.
TECHNICAL BID - COMPLIANCE STATEMENT
IP TELEPHONY NETWORK EQUIPMENTS
Product Specifications
Compliance
Yes /No
1
IP PBX SERVER MINIMUM TECHNICAL SPECIFICATIONS
The system should be based on server-gateway architecture running
on Linux OS supporting IP, Analog and Digital Extensions.
The servers should be of industry standard makes like DELL/HP/IBM
only. The proposed server should be capable of supporting at least
700 extensions in future. The expansion should not require any
additional hardware.
The system should be capable of deployment on virtualized
platforms like VMWare/Xen etc.
System should provide call control, mobility, IM and presence, and
Messaging, centralized licensing in a single server.
System should support secondary/redundant server for additional
capacity and resiliency.
The system should support standards-based multi-site networking,
using QSIG, H.323 trunks or advanced networking, to interoperate
with other PABX's, allowing feature transparency.
System should be able to provide backup/redundancy options in
case of failure of one server.
System should be able to provide centralized voicemail with the
option of Distributed centralized voicemail in case of connectivity
failure.
The system should support BRI/ PRI/ T1/ E1/Analog Trunks.
The server should have in-built atleast 2 nos auto-sensing
10/100/1000 Mbps LAN
The system should support internal MOH (Music on Hold), which
should be uploaded using the .Wav file and should have an audio
input port for external MOH connectivity.
The system should be 19” rack mountable.
Smartphone & Tablet Capabilities
The proposed hybrid-IP telephone system should have the ability to
be used/accessed from a smartphone and/or a tablet device
The Softphone should provide full call control from an iPhone or
Android powered smartphone.
Make and receive phone calls and instant messages, host and
attend audio conferences.
See employee availability via presence, and use Geo-tracking to
determine the location in the field.
All of this is done using the corporate directory, so there are no
personal cell phone numbers will be involved.
The Softphone application should be downloadable from Google
Playstore or Apple iTunes without any additional cost for any
number of device.
Remarks /Deviations
Telephony Features
Besides the normal Telephony features, the system should support
the following features :
Absent Text
Call Coverage
Call Forwarding
Call Hold
Call Intrude
Call Park
Call Pickup
Ring Back When Free
Suspend Call Waiting
Reclaim Call
Toggle Calls
Account Codes
Call Barring
Authorization codes
Bridged Appearance
Group Paging
Group Listen
Hot Desking
Mobile Twinning
Least Cost Routes
Alternate Route Selection
Flexible numbering Schemes
Time of Day and Date Routing of Calls
Call Recording
Maximum Call Length
PIN Restricted Calling
Time Profiles
Queuing
Queue announcements
Call Detail Recording
SMDR
Data Communication Features:
System should have in built-in DHCP Server, which should be able to
give IP Addresses to the endpoints.
System should support built-in Remote access server (RAS)
functionality.
System should support Diffserv for QoS ( Quality of service) for the
voice packets traveling over data networks
System should support NAT
System should support LDAP (Local Directory Access Protocol)
Terminal Support :
System should support the following type of terminals :
Analog Phones
Digital Phones
IP Hardphones
IP Softphones
Wireless IP Phones (802.a/b/g/n)
3rd party SIP telephones
Extensions and Trunks:
System should be able to support up-to 2000 extensions in any
combination.
System should have built-in H.323 gatekeeper functionality without
the need to put any additional hardware.
System should support SIP trunking to Internet Telephony Service
Providers, allowing non-SIP phones to make SIP calls.
System should support following types of trunks:
Analog Trunks
PRI
BRI
T1/ E1/ E1R2
Voicemail Features
System should have inbuilt voice mail system.
Voicemail to email option should be available
System should support unified messaging with Microsoft Exchange
or any IMAP compliant email application.
System should support voicemail access through web-browser
External Fax server integration should be possible.
VM should support text-to-Speech functionality
VM should support Dial-by-Name functionality
VM should support Auto Attendant
IVR functionality should be available
Conferencing Features:
The system should have built-in 128 party Meet-Me conferencing
bank.
Multiple conferences with variable number of users should be
possible within each of the conferencing banks.
System should be able to generate detailed reports about the
conference.
System should be able to send emails to all the participants giving
them the conferencing details
System should support PIN based security for conference calls.
Video Capability:
System should have IP Soft-phone capability with video support
System should be able to provide board-room units as extensions to
the system support various types of conference rooms. This unit
should also have option for multi-party conference up to 8 parties
(MCU).
Mobility Support:
System should support Mobile Twinning, enabling an extension and
an internal/ external number to operate together as a single
telephone. It should be possible to set external mobile devices as
twinning targets, even if the primary extension is logged out/
unplugged.
System should be able to provide ‘work from home’ features like
telecommuting and VPN hard phones.
Presence/IM/thin-client Application
System should support simplified call control features like tap to
call, tap to conference etc
Visual voice mail, IM, presence
Central directory access
Support for Android and iOS devices (smartphones, tablets)
Wireless Support:
System should support wireless IP Phones which will work through
the Access Points which are being used for Wireless Data network
supporting 802.11a/b/g protocol.
System should support IP DECT, wherein the system and the Base
Station are connected over the IP Network
Management utilities:
System should be able to be configured and administered using a
GUI based application
System should support SNMP based network management
In case SNMP management is not available, system should be
capable of sending event notifications to up-to 3 email addresses,
each with a different set of alarms
II IP PHONES
1
IP Deskphone - Operator's Console with 32 additional
buttons
IP Deskphone should supports minimum 16
administrable feature buttons on the phone itself – and
a 32-button expansion model provides access to a total
of 48 feature keys or speed dial buttons.
Each of the buttons should feature a dual LED (red,
green) providing explicit status for the user
The deskphone console should includes several fixed
feature keys for common telephone tasks including
conference, transfer, drop, hold and mute.
It should includes a high quality 2-way speakerphone,
and supports a broad portfolio of wired and wireless
headsets for the operator through its integrated
headset jack
It should have context sensitive user interface along
with 3 softkeys and a 4-way navigation cluster – ideal
for scrolling through the local contacts list or call logs
The viewing angle of the display should be adjustable
and should measure minimum 4 lines by 24 characters
or more.
The display should be backlit for easier viewing in all
lighting conditions
2
IP Desk Phone - Type-I
Should have backlit display – 3.5” diagonal with minimum 3
rows by 24 characters
8 line appearance/feature key buttons – with dual LED’s (red,
green)
2-way speakerphone
Permanently-labeled feature button for call history, contacts,
conference, headset, forward, volume, mute, speaker etc.
Message waiting indicator
Dual position flip stand
Four-way navigation cluster button
Contacts application – supports up to 100 entries
Call log – contains last 100 calls
Three contextual softkey buttons
Volume button – (separate volume levels in the handset,
headset, speaker, and ringer)
Quick-access Voicemail Message button
Ethernet (10/100) line interface with a secondary 10/100
port for collocated laptop or PC
PoE 802.3af class 2 device, also supports a local power supply
Headset interface
Standards-based codec support: G.711, G.729A/B, G.726
3
IP Deskphone - Type - II
Audio
G.722 wideband audio
Full-duplex speakerphone
Call Handling
SIP/H.323
Single line, 2 calls/line operated with “flash” key
Mute/Unmute
Last number redial
Transfer / Forward
3-way ad-hoc conferencing; supports basic, generic, openstandards SIP features
User Interface
Monochrome display with minimum two rows
Context-sensitive soft keys
Status indicators
Connections
Dual 10/100 Ethernet ports
Headset jack (RJ9 connector)
Power Requirements
Compatible with Power over Ethernet (PoE); requires PoE
Class 1 settings
4
IP Video Phone
The proposed video phone must support the following
features along with the standard telephony features:
Android operating system
CMOS camera with privacy shutter
Wi-Fi Enabled
Minimum 4.0" LCD Graphical Display
Dual switched 10/ 100/ 1000 Mbps ports with integrated PoE
Touch Screen
RJ9 headset jack, USB, SD, Mini HDMI
Integrated Bluetooth
Function keys for PHONEBOOK,HEADSET, MUTE, HOLD, MESSAGE,
TRANSFER, CONFERENCE, SPEAKERPHONE, VOLUME.
Video Codec supporting H.264, video resolution up to [email protected] fps
PoE/PoE+ support
III
1
Video Conferencing End Point & Display Unit
VC End Point should be from the same OEM as of the IP PBX
Proposed for smoother integration with IPT Network and should
have minimum following features :
The VC Room system must support H.323, and SIP standards for
communications
The VC Room System must Support High Definition room video up
to the 1080p60 format (1920x1080 pixels at 60fps progressive). It
should also provide a PTZ (Pan, Tilt Zoom) High Definition autofocus
camera with automatic exposure and automatic white balance
supporting up to the 1080p60 format, a minimum horizontal field of
view of 70°, at least a 5x optical zoom and a minimum range for PAN
of +/-100° and for TILT of +/- 25°. Camera parameters must be
configurable on the VC system user interface, and in particular
white balance, back light compensation, exposure compensation,
focus and sharpness.
The VC Room System must be able to support up to one camera and
two screens, and Support dual video capabilities both in H.323
(H.239) and SIP (BFCP based)
The VC Room System must provide full band (20 kHz) audio and
support both the ITU standard (G.719), ISO/MPEG low complexity
standard (MPEG AAC LC) and ISO/MPEG low delay standard (MPEG
AAC LD)
The VC Room System must provide one microphone POD echo
canceled. The possibility to add a further optional triple microphone
POD for larger rooms is desired.
The VC Room System must be capable of capturing high definition
content from a laptop/PC/DVI source up to 1920x1080 at 60fps,
rescaling it at 720p60 when exceeding such resolution
The VC Room System must provide the ability to send/receive
simultaneously 1080p60 video on the main channel and 1080p60
video on the dual video channel. The user should be able to define
the ratio between the bandwidth used for live video and
presentation.
The VC Room System must Include HD multipoint conferencing
capabilities (as option) supporting up to 4 sites in continuous
presence (1 local + 3 remote) up to 1080p30. It must provide the
capability of handling mixed mode multipoint with H.323 and SIP
simultaneously participating terminals, and support for dual video
while in a multipoint session. IP VC DESKTOP and MOBILE multipoint
videoconferencing support must be available, eventually with an
external server PC. H.264 High Profile support during multipoint
conferencing is required. Overlay of text with names of participants,
and indication of mute and active speaker is required.
Double LAN network port for public and private network connection
must be available as option
Audio I/O interface of the VC Room System must support both
Digital and Analog.
The VC Room System must include the optional feature to record
the conference (up to 1080p resolution) on a USB Key or Disk. The
file must be recorded in a standard format, compliant with common
multimedia PC/Mac players. Replay of the file from VC Room System
interface is required. During a conference, it must be possible
sharing recorded file with remote participants using standard data
sharing (H.239 / BFCP).
It’s desired that the User Interface of VC Room system allows an
easy control (chair control, roster integration) of multi-conferences
hosted by external MCUs
A control application with a multi-touch interface like the Apple
iPad is desired as option. This interface should enable the user to:
Dial an address with a list of the recent outgoing, incoming or
missed calls or Access the company directory and place a call from
the directory
Control the VC Room Camera (PTZ), mute microphone, change
volume, set DND, start and stop presenting
Inviting another participant by either dialing by address (IP, E.164 or
SIP URI) or by accessing the company directory
Moderate the meeting when connected to a network MCU
2
55" LFD LED Display with USB Port, LAN port, HDMI Port & wiFi
The Display should have aspect ratio of 16:9.
The Display should support true resolution of 1920X1080 pixels.
The Display should have minimum (Native) contrast ratio of 5000:1.
The Display should have minimum life span of 50,000 Hrs.
The Display should have 350cd/m2 Brightness
The display should have following input terminals.
a) RGB Input –Mini D-Sub 15 PIN x 1
b) DVI-D In – 24+1 PIN
c) RS-232C - D-Sub 9 PIN X 1
c) HDMI In
d) Component(CVBS Common) Port
e) RJ45
The Display should have in-built speakers (minimum 10W rms x 2)
The Display should support various types of mounting accessories
like:
a) Wall Mount Bracket
The display should have the following standards certification
a) RoHS compliant – For environment
b) UL/IEC – For safety
c) FCC – For radiations regulation
d) Energy Star 6.0 Certified.
The display should have the following special features:
a) The Auto Source Switching & Recovery
b) PIP/PBP, Image Rotation
c) Built in Media Player
d) Firmware Update by Network
e) Magic Clone(to USB)
f) Predefined Template for Vertical Usage
g) Multi Channel
h) Event Schedule, Backup Player
B
Sr No.
Conference Room / Smart Class Room Equipments for Recording, Capturing & Streaming of
Lectures, Workshops & Video Conferencing
Product Specifications
Compliance
Yes /No
1
Control System : 3-Series Control System
The control processor should support real-time, multi-tasking
modular programming architecture that can run 10 independant
programs simultaneously. The programming architecture should
lets programmers independently develop and run device-specific
programs for AV, lighting, HVAC, security, etc., allowing for the
optimization of each program, and allowing changes to be made to
one program without affecting the whole. Even as your system
grows, processing resources can easily be shifted from oneprocessor
to another without rewriting any code.
Vector floating point coprocessor
Onboard 512MB RAM & 4GB Flash memory
Expandable storage up to 1TB
Rear panel MMC memory card slot
High-speed USB 2.0 host port
Remarks /Deviations
Industry-standard Ethernet wired communications
Onboard e-Control Web server
It should support the user interfaces made for different platform
like iOS, Android & Windows operating systems.
Should supports Room scheduler software & touch screens and
SNMP remote management support.
Minimum One RS-232/422/485 COM port with hardware and
software handshaking
Two RS-232 COM ports with software handshaking only
8 IR/serial, 8 relay, and 8 Versiport I/O ports
Should Support IP network
Installer setup via same OEM softwareor Internet Explorer
Full Unicode (multi-language) support
Secure access though Active Directory integration or standalone
account management
Should support IIS v.6.0 Web Server
should be IPv6 ready
should have Front panel USB computer console port
should Includes power supply from day 1
Connectors
RELAY OUTPUT 1 – 8: (2) 8-pin 3.5mm detachable terminal block
comprising (8) normally open, isolated relays;
Rated 1 Amp, 30 Volts AC/DC;
MOV arc suppression across contacts
I/O 1 – 8: (1) 9-pin 3.5mm detachable terminal block comprising (8)
“Versiport” digital input/output or analog input ports (referenced to
GND);
Digital Input: Rated for 0-24 Volts DC, input impedance 20k Ohms,
logic threshold >3.125V low/0 and <1.875V high/1;
Digital Output: 250mA sink from maximum 24 Volts DC, catch
diodes for use with “real world” loads;
Analog Input: Rated for 0-10 Volts DC, protected to 24 Volts DC
maximum, input impedance 21k ohms with pull-up resistor
disabled;
Programmable 5 Volts, 2k ohms pull-up resistor per pin
IR - SERIAL OUTPUT 1 – 8: (2) 8-pin 3.5mm detachable terminal
block comprising (8) IR/Serial output ports;
IR output up to 1.2 MHz;
1-way serial TTL/RS-232 (0-5 Volts) up to 115.2k baud
COM 1: (1) 5-pin 3.5mm detachable terminal block;
Bidirectional RS-232/422/485 port;
Up to 115.2k baud; hardware and software handshaking support
COM 2 – 3: (2) 3-pin 3.5mm detachable terminal blocks;
Bidirectional RS-232 ports;
Up to 115.2k baud; software handshaking support
MEMORY: (1) MMC compatible card slot;
Accepts Multimedia Memory Cards (MMC) up to 32 GB for memory
expansion
USB: (1) USB Type A female;
USB 2.0 port for storage devices
LAN: (1) 8-wire RJ45 jack;
10Base-T/100Base-TX Ethernet port
NET: (1) 4-pin 3.5mm detachable terminal block, master port;
Outputs power to devices if a power pack is connected to the 24VDC
power input jack;
Receives network power if no power pack is connected to the
24VDC power input jack;
24VDC 2.0A: (1) 2.1mm barrel DC power jack, 24 Volt DC power
input;
PW-2420RU power supply included;
G: (1) 6-32 screw, chassis ground lug
COMPUTER (front): (1) USB Type B female;
USB 2.0 computer console port (6 ft cable should be included
included); For setup only
Controls & Indicators
PWR: (1) Green LED, indicates operating power supplied from power
pack or network
NET: (1) Amber LED, indicates communication with the system
MSG: (1) Red LED, indicates control system has generated an error
message
HW-R: (1) Recessed pushbutton for hardware reset
SW-R: (1) Recessed pushbutton for software reset
LAN (rear): (2) LEDs, green LED indicates Ethernet link status, amber
LED indicates Ethernet activity
Power Pack: 2.0 Amps @ 24 Volts DC;
100-240 Volts AC, 50/60 Hz power pack, model PW-2420RU
included
Available Power: 24 Watts (1 Amp @ 24 Volts DC) when using power
pack
Power Usage: 15 Watts (0.625 Amp @ 24 Volts DC) when using
network power
Heat Dissipation: 50 BTU/Hr
Mounting: Freestanding or 1U 19-inch rack-mountable
2
Digital Media Switcher : 16 x 16 DigitalMedia™ Switcher
QuickSwitch HD® technology manages HDCP keys for fast, reliable
switching.
Enables device control via CEC.
Delivers a unified HD signal distribution solution incorporating both
point-to-point wired and IP streaming technologies.
Provides lossless HD AV signal routing over twisted-pair wire or
fiber.
Integrates video, audio, networking, and control over one
cat5e/cat6 wire (Allows up to 330 ft) or multi modefiber (Allows up
to 1000 ft) or single mode fibre (Allows up to 7.5 miles (12 km)).
Affords full matrix switching with ultra high 12.5 Gbps backplane
data rate.
Performs automatic AV signal format management via EDID.
HDBaseT® Certified — Enables direct connection to third-party
HDBaseT.
Provides easy setup and diagnostics via front panel or software.
Can be communicated via LAN port/Ethernet. Includes integrated
Ethernet switch with Gigabit LAN port
Allows streaming over Ethernet with no distance limitations.
Modular inputs support a complete range of digital (HDMI, DVI-I, 3GSDI) and analog signal types (VGA, Component Video, S-Video,
Composite Video, etc.)
Enables high-performance H.264 streaming from any input source
Auto-Locking™ technology achieves rapid switching between
disparate sources
Detects and displays detailed video and audio input information
Allows independent scaling for every display through select DM
receivers
Distributes USB HID mouse and keyboard signals
Supports expanded USB device support using USB Extenders
Allows full audio and USB breakaway switching
Enables simultaneous output of stereo and surround sound audio
Having 10 HDMI Input with 4K video resolution support,6HDBaseT
inputs with 4K resolution support
Having 2HDBaseT output with 4K video resolution support, 6 HDMI
output with 4K video resolution support & 2 Multimode fibre
outputs
Private Network Mode — requires just one IP address for the
complete DM system
Configurable with up to 8 streaming outputs
Configurable with up to 16 DM, HDBaseT, and/or HDMI outputs
3
4K HDMI® Input Card for DM® Switchers ( Plug-in card)
Provides a single 4K HDMI® input
Handles video resolutions up to 4K and Ultra HD
Handles 3D video and Deep Color
Handles Dolby® True HD, DTS-HD®, and uncompressed 7.1 linear
PCM audio
HDCP compliant
Includes an HDMI output for pass-through of the input signal
Includes a stereo analog line-level audio output with volume
control
Allows extraction of stereo 2-channel audio signals
Enables device control via CEC
Enables USB HID signal extension for a local computer
Compatible with USB over Ethernet Extenders
Occupies a single DM switcher input card slot
Provides an HDMI problem solving solution using the optional DMCI
card interface
Connectors
HDMI IN
: (1) 19-pin Type A HDMI female; HDMI digital
video/audio input; Also supports DVI and DisplayPort Multimode
HDMI OUT
: (1) 19-pin Type A HDMI female; HDMI digital
video/audio output; Also supports DVI
USB HID : (1) USB Type B female; USB device port for connection to
the USB host interface of a computer or other USB HID-compliant
host
AUDIO OUT: (2) RCA female; Unbalanced stereo line-level audio
output; Output Impedance: 100 Ohms nominal;
Maximum Output Level: 2 Vrms
4
Input Card for Digital Mixer Switchers ( Plug-in card) : HDBaseT®
Certified 4K DigitalMedia 8G+™ Input Card for DM® Switchers
Provides a single DM 8G+® or HDBaseT® input for any Digital Media
Switcher with modular input card slots
Handles 4K and Ultra HD video resolutions
Handles 3D video and Deep Color
Handles Dolby® TrueHD, DTS-HD®, and uncompressed 7.1 linear
PCM audio
HDCP compliant
Supports cable lengths up to 330 ft (100 m) for all resolutions up to
UHD and 4K using DM Ultra cable
Supports cable lengths up to 330 ft (100 m) for 1080p, WUXGA, and
2K using DM 8G cable or CAT5e
Includes an HDMI® output for pass-through of the input signal
Includes a stereo analog line-level audio output with volume
control
Allows extraction of stereo 2-channel audio signals
Enables device control via CEC
Supports PoDM and PoH
Occupies a single DM switcher input card slot
Provides a rack-mountable DM 8G+ receiver solution using the
optional DMCI card interface
Conectors on the cards should be :
HDMI OUT: (1) 19-pin Type A HDMI female; HDMI digital
video/audio output; Also supports DVI
DM IN
:(1) 8-pin RJ45 female, shielded; DM 8G+ input, HDBaseT
compliant; PoDM and PoH PSE (Power Sourcing Equipment) port[;
Connects to the DM 8G+ output of a DM transmitter or other DM
device, or to an HDBaseT device, via CAT5e, DM-CBL-8G, or DM-CBLULTRA cable
POE IN :(1) 8-pin RJ45 female, PoE input; Connects to a DM-PSU8 or DM-PSU-16 PoDM Power Supply, or to an 802.3af or 802.3at
compliant PoE PSE (Power Sourcing Equipment), to enable PoDM
and PoH power sourcing.
AUDIO OUT: (2) RCA female; Unbalanced stereo line-level audio
output; Output Impedance: 100 Ohms nominal;
Maximum Output Level: 2 Vrms
5
2-Channel HDBaseT® Certified 4K DigitalMedia 8G+® Output Card
for DM® Switchers ( Plug-in card)
Modular output card for a Digital Media -MD16X16 switcher
Provides two independent 4K DM 8G+® outputs
HDBaseT® Certified — Enables direct connection to other HDBaseT
certified equipment
Includes a parallel HDMI® port on the first output
Handles video resolutions up to 4K and Ultra HD
Handles 3D video and Deep Color
Handles Dolby® True HD, DTS-HD®, and uncompressed 7.1 linear
PCM audio
HDCP compliant
Supports cable lengths up to 330 ft (100 m) for all resolutions up to
UHD and 4K using DM® Ultra cable
Supports cable lengths up to 330 ft (100 m) for 1080p, WUXGA, and
2K using DM 8G® cable or CAT5e
Supports cable lengths up to 230 ft (70 m) for UHD and 4K using DM
8G cable, or 165 ft (50 m) using CAT5e
Enables HDMI and HDBaseT device control via CEC
Supports PoDM and PoH
Occupies a single output card slot
Connectors on the Card should be :
DM OUT: (2) 8-pin RJ45 female, shielded, comprising (2) DM 8G+
outputs (HDBaseT compliant); PoDM and PoH PSE (Power Sourcing
Equipment) ports; Each connects to the DM 8G+ input of a DM
receiver or other DM device, or to an HDBaseT device, via
CAT5e, DM-CBL-8G, or DM-CBL-ULTRA cable
POE IN : (2) 8-pin RJ45 female comprising (2) PoE inputs; Each
connects to one port of a DM-PSU-8 or DM-PSU-16 PoDM Power
Supply, or 802.3af or 802.3at compliant PoE PSE (Power Sourcing
Equipment), to enable PoDM and PoH power sourcing via the
corresponding DM 8G+ output
HDMI : (1) 19-pin Type A HDMI, female; HDMI digital video/audio
output, DVI compatible; Outputs same signal as the left DM 8G+
output
6
2-Channel 4K Scaling HDMI® Output Card for DM® Switchers ( plugin card)
Modular output card for a DM-MD8X8, DM-MD16X16, or DMMD32X32 switcher
Provides two independent 4K HDMI® outputs
Includes a discrete 4K/60 scaler on each output
Upscales video and computer sources to match the native
resolution of any screen up to Ultra HD and 4K
Downscales 4K, UHD, and ultra-high resolution computer signals to
enable viewing on 1080p and lower-resolution displays
Handles any input resolution from standard NTSC 480i or PAL 576i,
to UHD and 4K
Provides intelligent frame rate conversion
Includes content-adaptive noise reduction
Includes motion-adaptive de-interlacing
Allows adjustable over-scan or under-scan up to 7.5%
Provides automatic 3D to 2D signal conversion
Automatically passes 3D video without scaling to 3D capable
displays
Supports left/right eye steering for dual-projector 3D setups
Handles Dolby® True HD, DTS-HD®, and uncompressed 7.1 linear
PCM audio
HDCP 2.2 compliant
Each output includes a balanced analog stereo audio output with
volume control
Allows extraction of stereo 2-channel audio signals
Enables device control via CEC
Occupies a single output card slot
Card should have following connectors
HDMI :(2) 19-pin Type A HDMI, female, comprising (2) HDMI digital
video/audio outputs (DVI compatible).
Audio (L, R): (2) 5-pin 3.5mm detachable terminal blocks comprising
(2) balanced/unbalanced stereo line-level outputs; Output
Impedance: 200 Ohms balanced, 100 Ohms unbalanced; Maximum
Output Level: 4 Vrms balanced, 2 Vrms unbalanced
7
Wireless Presentation Solution : Presentation Gateway Device
Enables wireless presentation of HD content using laptops, tablets,
and smartphones
Low cost, easy to use, and easy to deploy across any number of
rooms
Compatible with Windows®, OS X®, Apple® iOS®, and Android™
Allows simultaneous Displays of up to four presentation sources at
once in Quad View
Integrates with DigitalMedia & High Definition Video Capture
Hardware
Customizable welcome screen provides clear instructions for
presenters
Integrates seamlessly with Connected™ displays[2]
Compatible with virtually any display device[2]
Supports Full HD 1080p and UXGA display resolutions
Provides HDMI®, VGA, and analog audio outputs
Choice of connection methods accommodates all types of users and
organizations
Supports up to 32 simultaneous presenter device connections
(users)
Remote View: Allows up to 40 remote users to connect via a Web
browser to view and save images of the presentation
Display Control: Controls the display device over IP as part of the
presentation [2]
Control System Integration: Allows communication over IP with a
Control System for remote control and integration with other
equipment
Windows® and OS X® Client Software
OS Support: Windows® XP, Vista, 7, or 8; Mac® OS X® (versions 10.5
thru 10.8)
Video Frame Rate: 15 fps (typical), audio supported
Mobile Apps
OS Support: Apple® iOS®; Android™
Supported Files: MS PowerPoint® (.ppt, .pptx), MS Word (.doc,
.docx), MS Excel® (.xls, .xlsx), PDF (.pdf), JPEG (.jpg, .jpeg)
Shot&Show: Shares a static image of any app by using the screen
shot function
Video
Output Signal Types: HDMI®, RGB
Output Formats: HDMI, DVI[3], HD video up to 1080p60, computer
up to UXGA
Output Resolutions, Progressive: [email protected], [email protected],
[email protected] (720p60), [email protected], [email protected],
[email protected],
[email protected],
[email protected],
[email protected] (1080p60)
Output Resolutions, Interlaced: [email protected] (1080i30)
Underscan: Up to 7.5%
Audio
Output Signal Types: HDMI, analog stereo
Formats, HDMI: PCM 2-channel
Formats, Analog: Stereo 2-channel
Communications
Ethernet: 10/100 Mbps, auto-switching, auto-negotiating, full/half
duplex, DHCP, Web server
Connectors
5VDC 2.6A: (1) 2.0 x 3.0 mm DC power connector, 5 Volt DC power
input,
AUDIO: (1) 3.5mm TRS mini phone jack, unbalanced stereo line-level
audio output
HDMI: (1) 19-pin Type A HDMI female, HDMI digital video/audio
output,
Also supports DVI[3]
VGA: (1) DB15HD female, RGBHV (VGA) video output
LAN: (1) 8-wire RJ45, female; 10Base-T/100Base-TX Ethernet port
SERVICE: (1) USB Type A female, for factory use only
8
DigitalMedia 8G+™ Transmitter 201
It should be Installed in a double-gang electrical box to provide a
convenient interface for computers and high-definition AV sources
as part of a complete Digital Media system
It should functions as a DM transmitter and switcher, providing
HDMI®, VGA, and analog audio inputs along with a USB HID host
port.
It should also compatible with HDBaseT®, allowing it to be
connected directly to the input of an HDBaseT certified display
device
Video Features
Switcher : 2x1 combination digital/analog switch, QuickSwitch HD®
Input Signal Types: HDMI®, DVI[3], DisplayPort Multimode[3]
RGB/VGA, component[4], S-Video[4], composite[4]
Output Signal Types: HDBaseT® [1]
Formats: HDBaseT, HDMI, DVI, HDCP content protection support,
RGBHV, RGBS, RGsB, YPbPr, Y/C, NTSC, PAL
Audio Features
Switcher : 2x1 combination digital/analog switch.
Input Signal Types: HDMI, DisplayPort Multimode[3], analog stereo
Output Signal Types: HD Base T
Formats: Dolby Digital®, Dolby Digital EX, DTS®, DTS-ES, DTS 96/24,
up to 8ch PCMDigital-To-Analog Conversion: 24-bit 48 kHz .
Performance (analog): Frequency Response: 20Hz to 20kHz
±0.75dB;S/N Ratio: >90dB, 20Hz to 20kHz A-weighted; THD+N:
<0.05% @ 1kHz;Stereo Separation: >90dB
,
9
FlipTop™ Basic, Black Anodized
Flush mount tabletop connectivity in a stylish FlipTop™ design
An ideal complement to DigitalMedia™ Configurable connection
compartment allows versatile combinations of pullout cables, cable
retractors, connector plates, and AC power outlets
Tapered cable notch allows lid to be closed with cables plugged in
Lacing bar for under table cable management
Universal cutout size fits all new and future FlipTops™
Black anodized or brushed aluminum finish
10
FlipTop™ AC Power Outlet Module, Single, Universal
Single “universal” outlet, which accommodates several different
types of plugs.
It should be rated for 10 Amps at 100-240 Volts AC, 50/60 Hz
11
Cable Retractor for FlipTops™, HDMI®
Should Provides a refined cable management solution for Own
device FlipTops™
Eliminates hanging cable loops beneath the table
Easy-to-use — pull out the cable to its full length (3 ft / 0.9 m) to
latch, pull it again to retract
No levers or buttons to press
Mechanism to prevent whipping of the cable while retracting
12
Cable Retractor for FlipTops™, VGA
Provides a refined cable management solution for Own device
FlipTops™
Keeps interface cables at-the-ready
Eliminates hanging cable loops beneath the table
Easy-to-use — pull out the cable to its full length (3 ft / 0.9 m) to
latch, pull it again to retract
Mechanism to prevent whipping of the cable while retracting
13
Cable Retractor for FlipTops™, Audio
Provides a refined cable management solution for Own device
FlipTops™
Keeps interface cables at-the-ready
Eliminates hanging cable loops beneath the table
Easy-to-use — pull out the cable to its full length (3 ft / 0.9 m) to
latch, pull it again to retract
Mechanism to prevent whipping of the cable while retracting
14
Wall Plate DigitalMedia 8G+™ Transmitter 200, Black Textured
It Installs in a double-gang electrical box to provide a convenient
interface for computers and high-definition AV sources as part of a
complete DM system
It is ideal for wall, lectern, and floor box applications in a
boardroom, classroom, auditorium
It should also compatible with HDBaseT®, allowing it to be
connected directly to the input of an HDBaseT certified display
device
Video Features
Switcher : 2x1 combination digital/analog switch, QuickSwitch HD®
Input Signal Types: HDMI®, DVI[3], DisplayPort Multimode[3]
RGB/VGA, component[4], S-Video[4], composite[4]
Output Signal Types: HDBaseT® [1]
Formats: HDBaseT, HDMI, DVI, HDCP content protection support,
RGBHV, RGBS, RGsB, YPbPr, Y/C, NTSC, PAL
Audio Features
Switcher : 2x1 combination digital/analog switch.
Input Signal Types: HDMI, DisplayPort Multimode[3], analog stereo
Output Signal Types: HD Base T
15
2 Gang Decorator Style Faceplates, Black Textured
2-Port Face Plate
16
4K HDMI® over HDBaseT® Extender w/IR & RS-232, Black; includes
HD-RX3-C-Band HD-TX3-C-B
4K HDMI® over HDBaseT® Extender w/IR & RS-232
HDBaseT® Certified 4K Ultra HD signal extender
Extends uncompressed digital video and audio over a single CAT
type twisted pair cable
Supports cable lengths up to 330 ft (100 m) for all resolutions up to
4K and Ultra HD using DM® Ultra cable
Supports cable lengths up to 330 ft (100 m) for 1080p, WUXGA, and
2K using DM 8G® cable or CAT5e
Supports cable lengths up to 230 ft (70 m) for 4K and UHD using DM
8G cable, or 165 ft (50 m) using CAT5e
Compatible with HDBaseT receivers and display devices
Compatible with HDMI®, DVI, and DisplayPort Multimode
sources [4]
Supports Dolby® TrueHD, DTS-HD®, and uncompressed 7.1 linear
PCM audio
HDCP compliant
Passes CEC and EDID
Enables IR and RS-232 signal extension
24VDC power pack included
No programming or configuration required
Connectors – HD-TX3-C Transmitter:
HDMI IN: (1) 19-pin Type A HDMI female;
HDMI digital video/audio input;
IR IN: 1) 2-pin 3.5mm detachable terminal block;
IR repeater input port;
COM: (1) 3-pin 3.5mm detachable terminal block;
Bidirectional RS-232 port;
,
HDBaseT OUT : (1) 8-pin RJ45 female, shielded;
Connects to the HDBaseT IN port of the HD-RX3-C receiver via
CAT5e, DM-CBL-8G, or DM-CBL-ULTRA cable
Connectors – HD-RX3-C Receiver:
OUT: (1) 2-pin 3.5mm detachable terminal block;
IR repeater output IR port;
COM¨ (1) 3-pin 3.5mm detachable terminal block;
Bidirectional RS-232 port;
HDMI OUT: (1) 19-pin Type A HDMI female;
HDMI digital video/audio output
HDBaseT IN: (1) 8-pin RJ45 female, shielded;
Connects to the HDBaseT OUT port of the HD-TX3-C transmitter via
CAT5e, DM-CBL-8G, or DM-CBL-ULTRA cable
Construction: Metal, black finish with white or black polycarbonate
label overlay
Mounting: Freestanding, surface mount, or attach to a single rack
rail
17
DigitalMedia 8G+ 4K Receiver & Room Controller w/Scaler
Provides a controller and interface for an HD or 4K display device as
part of a complete Digital Media™ System
Digital Media 8G+® receiver, 4K/60 scaler, audio extractor, and
display controller
Connects to a DM® switcher or transmitter over a single CAT type
twisted pair cable
HDBaseT® Certified Enables direct connection to other HDBaseT
certified equipment
Provides one HDMI® or DVI display output
Upscales the input signal to match the native resolution of any
screen — including 4K and Ultra HD displays!
Downscales 4K, UHD, and ultra-high-resolution computer signals to
enable viewing on 1080p and other lower-resolution displays
Handles any input resolution from standard NTSC 480i or PAL 576i,
to UHD and 4K
Provides intelligent frame rate conversion
Includes content-adaptive noise reduction
Includes motion-adaptive de-interlacing
Allows adjustable overscan or underscan up to 7.5%
Provides automatic 3D to 2D signal conversion [4]
Automatically passes 3D video without scaling to 3D capable
displays
Supports left/right eye steering for dual-projector 3D setups
Supports up to 8x8 video wall processing
Handles Dolby® TrueHD, DTS-HD®, and uncompressed 7.1 linear
PCM audio
Provides a balanced stereo analog line-level audio output with
volume control [6]
Allows extraction of stereo 2-channel audio signals
HDCP 2.2 compliant
Supports cable lengths up to 330 ft (100 m) for all resolutions up to
UHD and 4K using DM Ultra cable
Supports cable lengths up to 230 ft (70 m) for UHD and 4K using DM
8G cable, or 165 ft (50 m) using CAT5e
Provides a 10/100 Ethernet LAN connection
Compatible with USB over Ethernet Extenders
Enables device control via CEC, IR, RS-232, and Ethernet
Provides two low-voltage relay control ports
Allows quick, easy setup and diagnostics
Powered via the DM connection or local power pack (included)
Low-profile surface mount design
SCALER
4K video scaler, motion-adaptive de-interlacer, intelligent frame
rate conversion, Deep Color support, 3D to 2D conversion , contentadaptive noise reduction, widescreen format selection (zoom,
stretch, maintain aspect-ratio, or 1:1), video wall processing up to 8
wide x up to 8 high
CONNECTORS
COM: (1) 5-pin 3.5mm detachable terminal block, bidirectional RS232 port; Up to 115.2k baud, hardware and software handshaking
support
IR(1-2) : (1) 4-pin 3.5mm detachable terminal block comprising (2)
IR/Serial ports; IR output up to 1.1 MHz; 1-way serial TTL/RS-232 (05 Volts) up to 19200 baud
AUDIO OUT L, R: (1) 5-pin 3.5mm detachable terminal block;
Balanced/unbalanced stereo line-level audio output
Output Impedance: 200 Ohms balanced, 100 Ohms unbalanced;
Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced
RELAY 1 – 2: (1) 4-pin 3.5mm detachable terminal block comprising
normally open, isolated relays; Rated 1 Amp, 30 Volts AC/DC; MOV
arc suppression across contacts
LAN: (1) 8-wire RJ45 female, shielded; 10Base-T/100Base-TX Ethernet port
HDMI OUT: (1) 19-pin Type A HDMI female; HDMI digital
video/audio output; Also supports DVI
DM IN: (2) LEDs, green LED indicates DM link status, amber LED
indicates video and HDCP signal presence
Power Requirement
Power Pack: 40 Volts AC, 50/60 Hz power pack, model PW2412WU included
Power over DM (PoDM): PoDM+ PD (Powered Device), capable of
being powered by a PoDM+ PSE (Power Sourcing Equipment),
conforms to IEEE 802.3at Type 2 Class 4 (25.5W)
18
High-Definition Capture Recorder
It should captures presentation content from a computer or other
source along with a live camera image and records them together in
full-motion HD. The two images may be composited on screen sideby-side or picture-in-picture (PIP)
Records the complete AV presentation, classroom lecture, or
training session
Captures in high-quality H.264 format at up to HD 1080p resolution
Allows live streaming of HD video and audio over an IP network
Extremely easy to use and flexible enough to fit any workflow
model.
Integrates easily into existing AV presentation systems and networks
Provides inputs for high-definition digital and analog AV sources
Built-in scaling ensures compatibility with a full range of sources
Provides a composite video input for the presenter's camera
Includes local AV output for confidence monitoring or presentation
pass-thru
Allows control system integration via Ethernet
Gigabit Ethernet enables high transfer rates for uploading of HD
media files
Easy out-of-the-box setup
Single-space 19" rack-mountable
Connectors - The device must have following connectors in-built in
the chasis and no external device should be required to get these
connection :
SPEECH IN (Unbalanced): (1) RCA female;
Unbalanced line-level audio input;
Input Impedance: 10k Ohms nominal;
Input Level: 2 Vrms maximum
SPEECH IN (Balanced): (1) 3-pin 3.5mm detachable terminal block;
Balanced/unbalanced line-level audio input;
Input Impedance: 17.5k Ohms nominal balanced/unbalanced;
Balanced Input Level: 4 Vrms maximum;
Unbalanced Input Level: 2 Vrms maximum
CONTENT AUDIO IN (Unbalanced): (1) 3.5mm TRS mini phone jack;
Unbalanced stereo line-level audio input;
Input Impedance: 18.5k Ohms nominal;
Input Level: 1 Vrms maximum
CONTENT AUDIO IN (Balanced): (1) 5-pin 3.5mm detachable
terminal block;
Balanced/unbalanced stereo line-level audio input;
Input Impedance: 24k Ohms nominal balanced/unbalanced;
Balanced Input Level: 4 Vrms maximum;
Unbalanced Input Level: 2 Vrms maximum
AUDIO OUT L, R (Unbalanced): (2) RCA female;
Unbalanced stereo line-level audio output;
Output Impedance: 100 Ohms nominal;
Output Level: 2 Vrms maximum
AUDIO OUT (Balanced): (1) 5-pin 3.5mm detachable terminal block;
Balanced/unbalanced stereo line-level audio output;
Output Impedance: 200 Ohms balanced, 100 Ohms unbalanced;
Balanced Output Level: 4 Vrms maximum;
Unbalanced Output Level: 2 Vrms maximum
CAMERA IN, COMPOSITE: (1) BNC female analog composite video
input;
RCA adapter included; Input Impedance: 75 Ohms nominal;
Input Level: 1 Vp-p nominal
CAMERA IN, 3G-SDI[4]: (1) BNC female, SDI video input;
Input Impedance: 75 Ohms nominal
CONTENT IN, RGBHV: (1) DB15HD female, RGB (VGA) input;
Formats: RGBHV, RGBS, RGsB;
Input Levels: 0.5 to 1.5 Vp-p with built-in DC restoration;
Input Impedance: 75 Ohms nominal;
Sync Detection: RGBHV, RGBS, RGsB; Sync Input Level: 3 to 5 Vp-p;
Sync Input Impedance: 511 Ohms nominal
CONTENT IN, HDMI: (1) 19-pin Type A HDMI female;
HDMI digital video/audio input;
Also supports DVI and DisplayPort Multimode[3]
LOOP OUT, RGBHV: (1) DB15HD female, buffered pass-thru from
RGBHV input
19
High-Definition Video Scaler, HDMI® In, HDMI Out
Provides a cost-effective, high-definition scaler with HDMI in and
out, and audio embedding and de-embedding
Automatically scales any input signal to match the native resolution
of your display
Supports a range of display resolutions up to Full HD 1080p and
WUXGA
Perfect for adapting all kinds of video devices to handle any input
resolution
Supports any input resolution up to Full HD 1080p and WUXGA
Performs deinterlacing of NTSC, PAL, and 1080i sources
Handles HDMI® signals with Deep Color and HDCP
Also handles DVI and DisplayPort Multimode sources
Handles Dolby Digital® 5.1, DTS® 5.1, and uncompressed 7.1 linear
PCM audio
Includes stereo analog audio input and output
Allows embedding of analog stereo audio to HDMI
Allows extraction of digital stereo audio to analog
Affords easy setup via on-screen display
Compact, low-profile surface mount design
Universal 100-240V external power pack included
20
10.1” Surface Mount Touch Screen, Black Smooth
Touch Screen Display
Display Type: TFT Active matrix color LCD
Size: 10.1 inch (257 mm) diagonal
Aspect Ratio: 16:10 WXGA
Resolution: 1280 x 800 pixels
Brightness: 400 nits (cd/m²)
Contrast: 800:1
Color Depth: 18-bit, 262k colors
Illumination: Edgelit LED
Viewing Angle: ±80° horizontal, ±80° vertical
Touch Screen: Projected Capacitive
Buttons available
Hard Keys: (5) Projected capacitive pushbuttons, programmable, prelabeled with icons for “Power”, “Home”, “Lights”, “Up”, and “Down”
Reset: (1) Miniature pushbutton on rear panel for hardware reset
Memory
LPDDR2 RAM: 1 GB
Flash: 4 GB
Maximum Project Size: 512 MB
Communications
Ethernet: 10/100 Mbps, auto-switching, auto-negotiating, autodiscovery, full/half duplex, DHCP, IEEE 802.3af and 802.3at Type 1
compliant
Video
Streaming Formats: H.264 (MPEG-4 part 10 AVC), MJPEG
Audio
Features: Built-in microphone and speakers, SIP Intercom
Audio Feedback Formats: MP3
Connectors
LAN PoE: (1) 8-wire RJ45 with 2 LED indicators;
10Base-T/100Base-TX Ethernet port, Power over
compliant;
Green and yellow LEDs indicate Ethernet port status
Ethernet
Power Requirements
Power over Ethernet: IEEE 802.3af (802.3at Type 1) Class 3 PoE
Powered Device
21
TableTop Kit for 10.1" Surface Mount Touch Screen
A stylish, versatile tabletop enclosure for the 10.1" Touch Screen.
Provides a 38° fixed operating angle
Allows permanent mounting using the optional swivel mount kit
Provides the choice of a rear or bottom wire exit.
22
PoE Injector, universal 100-250 Volts AC
It is an 802.3af compliant Power over Ethernet (PoE) power source
designed to support PoE powered devices. Standards-based Power
over Ethernet affords a one-wire solution for connecting Ethernet
devices, delivering power and data over a single CAT5/6 network
cable.
23
Keypad - International Version, Black Textured
Button Events" enable tap, double-tap, and press and hold
functionality
Customizable backlit button engraving[1]
White LED feedback indicators
Built-in LED blinking and bargraph logic
Auto-dimmable backlight and LED intensity
Ambient light sensor
2 contact closure inputs
Connections :
NET: (1) 4-pin terminal block;slave port, connects to control
network
INPUT (1-2): (1) 3-pin terminal block;Comprises (2) dry contact
closure sensing inputs
24
Distribution Hub : DIN Rail Distribution Hub
3-segment hub
For own networks with more than 20 devices
Configurable power distribution
should accommodate 6 DIN Module on wide DIN rail mounting
No programming required
25
DIN Rail High-Voltage Switch, 8 feeds, 8 channels
8 channels of power switching
Supports 120 to 240 Volt 50/60 Hz
Override input
Own device network communications
Setup via front panel or software
Fully Programmable functionality
9M wide DIN rail mounting
Load Ratings
Switch Channels: 8
Maximum Per Channel: 10 Amps incandescent, 5 Amps fluorescent,
0.5 HP @
120 to 240 Volts AC, 50/60 Hz;
5 Amps @ 30 Volts DC;
16 Amps Resistive
Module Total: 80 Amps incandescent, 40 Amps fluorescent @ 120 to
240 Volts
AC, 50/60 Hz
Load Types : Incandescent, Magnetic Low-voltage, Electronic LowVoltage, Neon /Cold Cathode, Florescent, Motors
26
DIN Rail 0-10V Fluorescent Dimmer, 4 feeds, 4 channels
4 channels of 0-10 Volt dimming control
Supports 120 and 220 to 240 Volt, 50/60 Hz applications
Allows switching of lighting and exhaust fan
Own device network Communication
Maximum per channel: 5 Amps @ 120 to 240 Volts AC, 50/60
Hz;600 Watts @ 120 Volts AC;1150 Watts @ 230 Volts AC; 1200
Watts @ 240 Volts AC, 0.5 HP;16 Amps Resistive
Module total:20 Amps @ 120 to 240 Volts AC, 50/60 Hz; 2400 Watts
@ 120 Volts AC; 4600 Watts @ 230 Volts AC; 4800 Watts @ 240
Volts AC
Switch load types: Incandescent, magnetic low-voltage, electronic
low-voltage, neon/cold cathode, fluorescent, motors
27
IR Emitter Probe w/Terminal Block Connector
Designed to adhere directly over the IR sensor window of a
television, DVD player, or any other
IR controllable device.
Connects to any control system with a 2-pin terminal block type
control IR port, providing a1-way IR control interface to the device.
It is composed of an infrared LED housed in a miniature shell. Its
integral 7 foot cable may be extended up to 1000 feet using
ordinary twisted pair cable.
Includes IR mask and two-sided tape for mounting.
Connectors
(1) 2-pin 3.5mm detachable terminal block for connection to a
Control system IR port
28
OEM Certified HDMI® Interface Cable, 6 ft
High-speed Category 2 HDMI cable
Supports 1080p60 HDTV with 16-bit color depth
Handles computer resolutions up to WQXGA
Supports SACD, DVD-Audio, Dolby® TrueHD, and DTS-HD Master Audio™
24k gold-plated 19-pin Type A connectors
High-flex CL3-rated jacket
RoHS compliant
29
OEM Certified Computer VGA Interface Cable w/Audio, 6 ft
High-bandwidth computer VGA cable w/audio
Integrated mini-TRS stereo audio cable
Supports computer resolutions up to WUXGA
High-density 15-pin connectors
RoHS compliant
30
Locking High-Speed HDMI® Cable, 2 ft
A premium HDMI interconnect with an ingenious locking connector
design.
High-speed HDMI certified
Perfect Lock™ connector with 25 lb retention
CL2/FT4 rated for in-wall use
Supports 3D, Deep Color, 4K, and audio return channel
31
Controlling Mobile based App for Apple® iOS® & Android™
operation without a connection to a own private control system
Free download provides a working app with limited functionality
Full version enabled through Provides the Own device touch screen
experience on an Apple® iOS® or Android™ device
Control your home or workplace using your iPhone®, iPad®, iPod
touch®, Apple Watch®, Android smartphone, or Android tablet
Provides an extensively customizable user interface
Enables control of lights, media, climate, security, and more
Affords full system control with real-time status feedback and
metadata
Supports Smart Graphics™ and Rava® SIP Intercom
Allows viewing live streaming video from security cameras and
servers
Integrates seamlessly with third-party apps
Allows control of multiple Own private systems from one device
Compatible with Wi-Fi® and mobile data networks
Utilizes SSL secured communication
Requires no special server or 3rd-party service (no extra fees!)
Programmed just like a own private touch screen
Create one UI and run it on multiple own private touch screens,
Apple devices, and Android devices without modification
32
Streaming Output Card for Digital Media Switchers
A modular output card for Digital Matrix 16x16 switchers. Provides
one H.264 streaming output.
Modular output card for a DM-MD8X8, DM-MD16X16, or DMMD32X32 switcher
Provides a single streaming output
Allows high-definition AV signal distribution over IP with no distance
limitations
Supports streaming at resolutions up to 1080p30 and bitrates up to
25 Mbps
Employs high-quality H.264 video and AAC stereo audio encoding
Built-in scaler ensures fast, trouble-free switching between
disparate sources
Supports PIP windowing, audio mixing, and single-frame switching
between any two inputs
Allows streaming via the Control LAN or a dedicated Content LAN
Occupies a single output card slot
Connector
CONTENT LAN:(1) 8-pin RJ45 female; 10Base-T/100BaseTX/1000Base-T Ethernet port; Provides a dedicated LAN connection
for streaming only, used in lieu of streaming via the switcher's main
LAN port
33
Remote Asset Management Software - 5 Rooms
The Remote Asset Management Software will be used for AV and
technology management View room status, track maintenance on
devices, schedule end-of-day shutdown, book meetings in rooms,
provide remote help desk assistance, capture and distribute
multimedia presentations, and more — all from the web-based
interface.
Monitor, manage, and schedule meeting rooms enterprise-wide
Streamline the help desk with chat and real-time room status
Provide remote assistance — control the display, source, volume
and more
Track and analyze room usage with robust reporting using built-in
templates
Receive instant e-mail notifications for scheduled maintenance or
when a display is offline
Schedule rooms via Microsoft® Outlook®, IBM® Notes®,
CollegeNET® 25Live® (R25®), and Google Calendar™
Room status and ad-hoc booking via touch screen
Use instant messaging to communicate through the room’s touch
screen
Auto-discover assets upon deployment for improved tracking
Schedule end-of-day shutdown for AV equipment
Total Room Support capability : The software should be capable to
supports up to 750 connected rooms on one server
34
Full HD PTZ Camera Type-I : Full HD PTZ Camera with 20X Optical
Zoom, 12 x Digital Zoom, 30 fps frame rate, 55 degree horizontal
viewing angle and with HD-SDI Video Output
Pan Angle : -175 to + 175 degrees
Pan Speed : 0.25 to 60 degrees/sec
Tilt Angle : -30 to +90 degrees
Tilt Speed : 0.25 to 60 degrees/sec
Analog Output : RGB / Y/Pb/P(D-sub 15-pin), Y/C (4 pin Mini DIN),
VBS (BNC)
Angle of View : 3.3 degrees (tele end ) to 55.1 degrees (wide end)
Backlight Compensation : On/Off
Built-in Video Output : D-sub 15 pin: HD video out, Y/Pb/Pr or RGB,
HD, VD or SYNC, Mini DIN 4 pin: Y/C , BNC: Composite
CCD Effective Pixel : Approx. 2.07 mega pixels
Camera Control Interface : RS-232C (VISCA protocol)/RS-422 (VISCA
protocol)
Effective Pixel : 2.07 mega pixels or better
Focal Length : f=4.6 to 82.8mm (F1.6 to F2.8)
Focus System : Auto/Manual
Image Device : 1/3 type CMOS x1
Minimum Illumination : 6 lx (50 IRE, F1.6, 24dB)
35
Desktop Document Camera : Desktop Visualizer, 2 Mega Pixel,
1080p Full HD, 1/3” CMOS
Pick-up Device : CMOS
Output Resolution : SXGA (1280x 1024), WXGA (1280 x 800), 1080p
Frame Rate : 30 frames/sec.
Zooming : Min 16X Optical Zoom and 12 X Digital Zoom
Lamp : Top Light: LED x 2. Built-in Back Light for negatives and slides.
Built in Storage : Min 240 frames
External Storage : Supports USB drive upto 32 GB
Recording : One touch Video / Audio recording in standalone mode
with built-in microphone.
Image Rotation: 0, 180, mirror, flip.
Inputs : VGA Input HD-SUB 15 Pins Female x 1, HDMI x 1, Audio In x
1, Buil in MIC x 1
Outputs : VGA Output HD-SUB 15 Pins Female x 2, HDMI x 1,
Composite Video x 1, USB 2.0 High Speed x 1, Audio Out x 1
36
37
6 feet x 4 ft Infrared Interactive White Board with Ceramic Surface
3LCD + Pure Laser WUXGA Projector with 4100 Lumens, Contrast
Ratio - 10000:1, Light Source Life : 20,000 Hours and Edge Blending
features in-built.
Technology : 3LCD + Pure Laser
Resolution / Brightness : WUXGA 4,100 Lumens
Contrast Ratio : 1000:1
Installation Flexibility
Wide Zoom : x1.6
Lens Shift : V:+60%/0% H:+\32%
HV keystone/ Warp : V/H: +-30deg
Edge Blending
Tilt Free / Portrait
Light Source Life : 20,000 Hours
Synchronized Lamp/Filter : Filter 12K-20KH
38
39
40
Motorized Hydraulic Projector Lift
Motorized Projector Screen - 8 feet x 6 feet - Wall Mount with IR
Remote
85" LED LFD Professional Display with VGA, HDMI, DVI-D, USB &
LAN ports with Wall Mounting Bracket. ( The diagonal display size
should be minimum 85" or above)
The Display should have Panel technology : 120Hz Slim Direct LED
BLU
The Display should support true resolution of 3840 x 2160 (16:9) 4K
UHD
The Display should have minimum (Native) contrast ratio of 5000:1.
The Display should have minimum life span of 50,000 Hrs.
The Display should have viewing angle of 178 Degree Horizontal &
178 Degree Vertical
The Display should have Brightness of 500 nits
The display should have following input terminals.
a) RGB Input –Mini D-Sub 15 PIN x 1
b) DVI-D In – 24+1 PIN
c) RS-232C - D-Sub 9 PIN X 1
c) Video : 3 x HDMI In
d) AV Port , Stereo Mini Jack Audio In and Stereo Mini Jack - Audio
Out
e) Display Port 1.1 & Display Port 1.2
RJ-45 LAN Port, USB Port
The LCD should have in-built speakers (minimum 10W rms x 2)
The Display should support various types of mounting accessories
like:
a) Wall Mount Bracket
The display should have the following standards certification
a) RoHS compliant – For environment
b) UL/IEC – For safety
c) FCC – For radiations regulation
d) Energy Star 6.0 Certified.
The display should have the following special features:
a) The Auto Source Switching & Recovery
b) Lamp Error Detection
c) Super Clear Coating
d) Temperature Sensor
e) Pivot Display, Image Rotation, Button Lock
f) WiFi Embedded, WiDi 2.0
Inbuilt/integrated Player with more than 2 Ghz Processor, 2 GB
RAM, 32 GB Storage, Windows OS with internet explorer facility
Mobile Control, Event Schedule, Backup Player
PC-less Touch, MagicPresenter
24X7 application
41
55" LFD LED Display with USB Port, LAN port, HDMI Port & wiFi
The Display should have aspect ratio of 16:9.
The Display should support true resolution of 1920X1080 pixels.
The Display should have minimum (Native) contrast ratio of 5000:1.
The Display should have minimum life span of 50,000 Hrs.
The Display should have 350cd/m2 Brightness
The display should have following input terminals.
a) RGB Input –Mini D-Sub 15 PIN x 1
b) DVI-D In – 24+1 PIN
c) RS-232C - D-Sub 9 PIN X 1
c) HDMI In
d) Component(CVBS Common) Port
e) RJ45
The Display should have in-built speakers (minimum 10W rms x 2)
The Display should support various types of mounting accessories
like:
a) Wall Mount Bracket
The display should have the following standards certification
a) RoHS compliant – For environment
b) UL/IEC – For safety
c) FCC – For radiations regulation
d) Energy Star 6.0 Certified.
The display should have the following special features:
a) The Auto Source Switching & Recovery
b) PIP/PBP, Image Rotation
c) Built in Media Player
d) Firmware Update by Network
e) Magic Clone(to USB)
f) Predefined Template for Vertical Usage
g) Multi Channel
h) Event Schedule, Backup Player
42
Wall /Ceiling Mounting Bracket for the 55" LFD LED Display
43
Content Producing, AV Mixing, Final Cut Live Streaming and
Recording Device
Video Switcher, Content Producer & Audio Mixer as a Single
Module ( PAL B Format ) should support following minimum
HD Video Switcher
Video format supported : 1080/50i, 720/50p, RGB 1024x768 to 1920
x 1080
Video inputs : 4 x HD-SDI/SD-SDI, 2xComposite
Computer input : 2 x HDMI / 2xVGA
Video output : 3 x HD-SDI, 1 x HDMI, 1 xVGA
Video processing : RGB 4:2:2 sampling 10 bit or better
Video effects : Mix to Wipe patterns.
Display : Display is built-in within the switcher, the display panel
must be 15 inch or higher.
Recorder : Built-in recorder for Recoding Full HD 1920 x 1080 videos.
Microphone : Built-in Omni-directional stereo electret condenser
microphone
Capture Capabilities : The system should be able to make a PTZ
camera motion-based tracking to track the motion of the host.
Audio Mixer
No. of input channels : 4 Nos. with low noise mic preamp, level,
gain, EQ, aux, pan, mute and mono controls
Interface : XLR
Outputs : 2 Nos.
Gain range : 60 dB or higher
44
Streaming Server & Video on Demand Hardware : Minimum
Specifications
Server should be based on Intel X86 architecture, Red Hat
Enterprise Linux OS, Storage : 1 TB internal HDD
Should include video on demand functionality
Form Factor : 1 RU Form Factor
Input Interface
IP Stream input over multiple Ethernet Ports
Input Stream
Live : MPEG2TS (SPTS & MPTS), MPEG TS/RTP, RTMP
File : MPEG2 TS/ MPEG2 PS, MP4, MKV, FLV, WAV, 3GP
INPUT Video CODEC : MPEG2 HL/ML, MPEG4 SP/ASP, H264
BP/MP/HP
INPUT Audio Codec : AAC-LC, HE-AAC v1, HE-AAC v2, AC3, MP3,
MP2, LPCM
OUTPUT INTERFACE
IP stream output over multiple Ethernet ports
OUTPUT STREAMING FORMATS
Apple HLS, Microsoft Smooth Streaming, Flash RTMP, RTSP, MPEG
TS over UDP, File Mode
Output Video through Tru-Transcode using RAFT, HELM and SAND
45
C
Podium to accomodate Laptop, Desktop Visualizer, 10.1" Display (
for controlling the conference room equipments), Goose neck
Microphone, Table top Light,etc. - custom made.
Podium should have Desktop Box with RJ 45 x 2, Audio Jack x 1,
HDMI x 2, VGA x 1 and Universal Power Socket x 2
Audio System Components
Sr No. Product Specifications
Compliance
Yes /No
1
2
Gooseneck Microphone with a lightring indicates the spokeperson
that is allowed to take the floor, 40cm length , XLR 5M connector,
Pre - polarized condenser microphone for transducer principle,
Accoustic : Cardiod, Frequency rersponse : 50 Hz - 20 KHz, Nominal
Impedance : <100 ohm, MSPL : 130 db SPL, Connectivity : XLR 5M.
The microphone shall be a pre-polarized condenser designed for
permanent installation or portable applications.
It shall have a microphone capsule with a cardioid polar pattern
with uniform 120° angle of acceptance (-3dB)
It shall have a frequency response of 50 Hz to 20,000 Hz and be
capable of handling sound input levels up to 130 dBspl
Nominal equivalent noise level shall be 26 dBA (37 dB weighted as
per CCIR 468-3)
Output shall be low impedance balanced ( (<100 ohms).Operating
temperature shall be 32° to 104° F (0° to 40° C)
The microphone shall operate from an external 12V to 48V DC
phantom power source; current consumption shall be 3 mA
The microphone shall offer radio frequency interference (RFI)
shielding against intermodulation from wireless equipment or
devices.
It shall incorporate a self-contained power module with an XLR3Mtype connector at the base.
The microphone shall be a gooseneck design ensuring precise
alignment of the microphone and noiseless operation
The table stand for connecting and operating XLR gooseneck
microphones shall be rugged and unobtrusive.
It shall have a programmable microphone button (Toggle on/off,
PTM, PTT and permanent on) and a bi-color LED ring for status
indication shall be provided.
The table stand shall feature an XLR-5F microphone input, an XLR5M microphone output and a TTL logic connector with logic inputs
and outputs
The logic output voltage shall be high level > 2.4 and low level < 0.4
V
the logic input voltage shall be high level > 2.0 V and low level < 0.8
V.
The table stand shall operate on 48 V phantom power. Current
consumption shall be 3.7 mA.
Remarks /Deviations
3
Wireless Hanheld Microphone with frequency Transmission /
receiving frequesncies : 20 channels bank, 1 fixed bank, 12 factory
preset channels each, AF frequency response : 25 - 18.000Hz, S/N
ratio ( at 1mV and peak deviation ) : >110dBA.
4
Wireless clip-on microphone (Collar Microphones) , frequency
response : 80 - 18000Hz, Presets : 12, Sound pressure level : 120 dB (
SPL ) max., THD < 0.9%, RF output power : 30 mW.
5
8" wooden design cabinet loudspeaker, 8ohm/300watt full range,
wall bracket and pole mount tube included, black - priced per piece
and sold per piece
6
2-channel power amplifier 2 x 600Watts @ 4Ohms, convection
cooled, 1U 19" rackmount
7
Digital signal Processor with 8 microphone input and 2
speaker with inbuilt programming. DSP must be of the same
make as microphones
8
Bose QuietComfort 25 Acoustic Noise Cancelling headphones
9
Cables from the beow mentioned brands which includes Speaker
cable, HDMi cable, Audio Cable and power cable. Approved makes:
Extron, kramer, Beldon, Percon, nT
D
NETWORKING EQUIPMENT REQUIRED FOR THE CONFERENCE ROOM
Sr No.
Product Specifications
Compliance
Yes /No
1
24-Port PoE+ Switch with 10/100/1000 Base-T PoE Ports + 2 XFP
Ports
Architecture
The switch should have 24 x 10/100/1000 Base-T PoE ports with 2
SFP+ Ports
The Switch should support Stacking from day 1.
The stacking port should be separate from that of uplink SFP +
Ports.
The switch should support stacking for minimum 8 switch stack and
support a stacking bandwidth/throughput of 60 Gbps. The stacking
should support single IP address management.
The switch should support GE SFP and 10 GE SFP+ on any 2 ports
Should have at least 100Gbps of forwarding bandwidth
Should have switching throughput of up to 65 million pps
MAC Address table size of 12000 entries
The Switch should be 19” Rack-Mountable / 1 rack unit (RU)
Resiliency and high availability
Should support IEEE 802.3ad Link Aggregation Control Protocol
(LACP)
Should support IEEE 802.1s Multiple Spanning Tree Protocol
Should support Redundant Power Supply
Layer 2 and Layer-3 features
Remarks /Deviations
Should support IEEE 802.1Q ( 4K VLAN IDs) and 250 VLANs
simultaneously
Should support feature allowing automatic learning and dynamic
assignment of VLANs and dynamic trunk configurations across all
switches
Should support Jumbo frames
Should support Inter-VLAN Routing and Static IP routing
Should be IPv6 Capable supporting IPv6 host, Dual stack (IPv4/IPv6)
and MLD snooping
Security
Should support Port security and MAC address lockout
Should support Access control lists (ACLs) to provide IP Layer 3
filtering based on source/destination IP address/subnet and
source/destination TCP/UDP port number
Should support IEEE 802.1X user authentication, Web-based
authentication and MAC-based authentication
Should support DHCP Snooping
Should support Dynamic ARP protection to block ARP broadcasts
from unauthorized hosts, preventing eavesdropping or theft of
network data
DHCP protection to block DHCP packets from unauthorized DHCP
servers, preventing denial-of-service attacks
Should support Secure FTP for secure file transfer to/from the
switch
Should support Source Port Filtering allowing only specified ports to
communicate with each other
Should support TACACS+ and RADIUS authentication for secure
switch CLI logon
Should support SSHv2 and SSL allowing secure access to the switch
Convergence and QoS
Should support IP multicast Snooping (data-driven IGMP)
Should support IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
Should support LLDP-MED (Media Endpoint Discovery)
Should support IEEE 802.1p Traffic prioritization allowing real-time
traffic classification into 4 priority levels mapped to 4 queues
Should be able to set the IEEE 802.1p priority tag based on IP
address, IP Type of Service (ToS), TCP/UDP port number, source
port, and DiffServ
Should support per-port Rate Limiting setting ingress enforced
maximums
The switch should support 4 queues and one of them should be
strict priority queue which helps ensure that the highest-priority
packets are serviced ahead of all other traffic.
Advance Features
The switch should have feature to provide real-time network event
detection and onboard automation
The switch should support Multicast VLAN Registration
The Switch should support IEEE 802.1AE MACsec. MACsec should
provide Layer 2, line rate Ethernet data confidentiality and integrity
on host facing ports, protecting against man-in-the-middle attacks
(snooping, tampering, and replay).
The switch should support Enhanced Energy management feature
for operational cost optimization by measuring actual power
consumption of the PoE devices, reporting, and reducing energy
consumption across the network. The Energy management feature
should enable NIT Nagaland to measure the power consumption of
network infrastructure and network-attached devices and manage
power consumption with specific policies, reducing power
consumption to realize increased cost savings, potentially affecting
any powered device. The switch should have support capabilities to
support energy consumption, energy reports and energy
management.
The switch should support feature allowing unidirectional links
caused by incorrect fiber-optic wiring or port faults to be detected
and disabled on fiber-optic interfaces.
The switch should have feature to provide automatic configuration
as devices connect to the switch port, allowing auto detection and
plug and play of the device onto the network.
The switch should support feature which should be a transparent
plug-and-play technology to configure the OS Software image and
switch configuration without user intervention. This feature should
utilize dynamic IP address allocation and theassistance of other
switches to facilitate installation providing transparent network plug
and play.
The switch should support feature to provide a single point of
management for a group of switches and in addition adds the ability
archive and backup configuration files to a file server or switch
allowing seamless zero touch switch replacement.
The switch should support feature which should simplify QoS
configuration in voice over IP (VoIP) networks by issuing interface
and global switch commands to detect IP phones, classify traffic,
and help enable egress queue configuration.
Manageability
Should support Port mirroring
Should support command authorization leveraging RADIUS to link a
custom list of CLI commands to individual network administrator’s
login
Should support Multiple configuration files
Should support DLDP / UDLD
Should support SNMP v1, v2 & v3
Sr No.
Product Specifications
Compliance
Yes /No
2
Wireless Access Point - 802.11ac - Indoor
The APs should support the 802.11a, 802.11b, 802.11g and 11n and
ac standards. It should also support 802.11ac standard in the 5 GHz
band.
Operation in dual band radio is essential
Should support minimum 2x2 or higher MIMO with 2 spatial
streams on both radio bands to provide up to 867mbps data rate
in .ac.
The access points should be centrally managed.
Remarks /Deviations
In some small isolated environments the AP should be able to
function as a full-fledged stand-alone access point without the
requirement of a controller.
Security mechanisms should be in place to protect the
communication between the Access Point controller and the Access
Points.
Since most radio interference come from the WLAN network itself
the vendor should specify what mechanisms such as beam steering/
adaptive antenna technology/ beamforming are available in
combination to focus the energy on the destination STA and
minimize radio interference with the surrounding of the AP. The
vendor should specify if the activation of such feature is still
compatible with 802.11n spatial multiplexing.
Since the WLAN network will be using an unlicensed band the
solution should have mechanisms that reduce the impact of
interference generated by other radio equipment operating in the
same band. Describe techniques supported.
The access point should be able to detect clients that have dual
band capability and automatically steer those client to use the 5GHz
band instead of the 2.4GHz band.
The antennas to be dual polarised and should be integrated inside
the access point enclosure to minimize damage and create a low
profile unit that does not stand out visually.
The access point should have 1 Gigabit Ethernet port.
The access point should support 802.1q VLAN tagging
The access point should support WPA2 enterprise authentication
and AES/CCMP encryption. AP should support Authentication via
802.1X and Active Directory.
Implement Wi-Fi alliance standards WMM, 802.11d, 802.11h and
802.11e
The Access Point should provide for concurrent support for high
definition IP Video, Voice and Data application without needing any
configuration. This feature should be demonstrable.
Support RF auto-channel selection by the following three methods:
a) measuring energy levels on the channel; b) monitoring for 802.11
signal structures and; (c) detecting radar pulses. Other similar forms
of smart selection shall also be accepted.
Channel selection based on measuring throughput capacity in real
time and switching to another channel should the capacity fall
below the statistical average of all channels without using
background scanning as a method.
Should support Transmit power tuning in 1dB increments in order to
reduce interference and RF hazards
Device antenna gain (integrated) must be at least 4dBi and should
provide automatic interference rejection of about 10dB.
Should support up to 200 clients per AP
Should support DHCP Option 82 in standalone mode (without
Controller) as well as in Managed mode (with Controller)
For troubleshooting purposes, the administrator should have the
ability to remotely capture 802.11 and / or 802.3 frames from an
access point without disrupting client access.
Operating Temperature: 0°C - 40°C
Operating Humidity: 10 % - 95% non-condensing.
Should be plenum rated and comply to RoHS
Should be WiFi certified; WiFi certificate to be enclosed
Should be WPC approved; ETA certificate to be enclosed
Mechanism for physical device locking using padlock /Kensington
lock / equivalent
3
24-Port Loaded Patch Panel UTP Cat 6
4
Cat 6 UTP Cables
5
Informationa Outlet - UTP Cat 6 - RJ-45 Inserts for I/O
6
I/O Face Plate
7
Cat 6 UTP Patch Cord - 1 mtr
8
Cat 6 UTP Pacth Cord - 2 mtr
E
Furnishing of Seminar Hall - Electrical Lighting, Acoustic Wall & Ceiling Panelling,etc.
(a)
Lighting Requirement of the Seminar Hall
Sr No.
Product Specifications
Compliance
Remarks /Deviations
Yes /No
1
16W LED downlighter with High power, high efficiency Chip-OnBoard (COB) LED module lumens >=1200 Lumens,High transmitivity,
non-yellowing PMMA diffuser,Pressure die cast aluminum housing
with special wave shaped radial fins, black powder coated for
superior thermal performance,Aesthetic white rim molded in
engineering plastic.Driver will be 1-10 V Analog dimmable driver
integrated with fixture.
2
2' x 2' LED Fixutre with high efficient LEDs - 31.6 Watts ,seamlessly
designed to integrated with grid ceiling with HET duffuser (high
efficient translucense) diffuser for better light output.Driver will be
1-10 V Analog dimmable driver integrated with fixture.
3
Required Electrical Wiring for connecting all the above LED lights in
the conference room and terminating them in termination block
including all necessary accessories
(b)
Sr No.
Acoustic panelling of Walls & Ceiling of the Seminar Hall
Product Specifications
Compliance
Yes /No
1
For Acoustics Wall Panel
Supply and installation of Reputed Brand Superfine wood wool
panel of size 1200 x 600 x 15mm mounted on proprietory supplied
G I Frame work consisting of basic profile, main profile,edge profile
and spacer.
Tile Specification :
Tile description : Magnesite bonded wood wool acoustic panel with
fibre width of 1mm
1200 * 600 * 15mm thickness
Edge Detail : Square Edge (GK)
Reaction to fire acc to EN 13501-1 B-s1,d0
Sound Absorption Value aw up to 1.00
Thickness/Weight : 15 mm 7.8 Kg/m2
Remarks /Deviations
2
For False Ceiling
Supply and installation of Reputed Make Ceiling Tiles made of
mineral wool of size 600x600x 15 mm suspended by using OEM
supplied ceiling suspension system to consist of 2mm or 3mm GI
suspension rod/wire with adjustable Butterfly Clips of 4mm dia
securely affixed to structural ceiling using 10mm dia hook type
anchor fastener . Ceiling Suspnsion System to be fixed at interval (
grid ) of 1200mm in both directions. Supplied ceiling suspension
system to consist of Main Runners @ 600mm and joined by Cross
Tees @ 600mm to form overall grid opening of 600mm * 600mm
centre to centre. Additional cross tees are to be placed where
appropriate for light fixtures, AC diffusers etc. The grid width can be
15mm or 24mm. The main runners and cross tees to have click
installation system. The Grid system shall be hot dipped galvanized
steel sections, with exposed surfaces chemically cleaned and capped
prefinished in high - gloss polyster enamel with two coat system on
cold rolled steel.
Tile Specification :
Tile Type : Lay - in ceiling type.
600 * 600 * 15mm thickness
Edge Detail : Recessed Bevelled Edge (VT)
Light Reflectance : upto 90%.
Humidity Resistance : up to 95% RH
Colour : White Similar to RAL 9010.
Thermal Conductivity : 0.040 W/mK as per EN 12667
NRC = 0.60 as per ASTM C 423
Sound Attenuation : 34 dB as per EN 20140-9
Thickness/Weight : 15 mm 4.5 Kg/m2
3
Curtains for the 6 nos of Windows of size 4 feet x 4 feet - Curtain
size : 5 feet x 6 feet with thick light stopping linel and curtain clothes
to match the fabric of the wall panneling
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement