spa owner`s manual

SPA OWNER’S MANUAL

IMPORTANT SAFETY INSTRUCTIONS

PART A – GENERAL MANUAL

(APPLIES TO ALL SPAS)

Pour voir ou imprimer ce document en Français, veuillez visiter:

http://www.sunrisespas.com/site/owners

INSTALLATION AND ELECTRICAL CONNECTION

START UP AND OPERATION

MAINTENANCE

O1M-A-17

Read in conjunction with Part B – brand specific manual to form a complete Owner’s Manual

2

INDEX

Table of Contents

CONGRATULATIONS ON THE PURCHASE OF YOUR NEW SPA ................................................................................................................... 3

YOUR PERSONAL SPA DATA ....................................................................................................................................................................... 5

IMPORTANT SAFETY INSTRUCTIONS .......................................................................................................................................................... 6

INSTALLATION INSTRUCTIONS ................................................................................................................................................................... 9

WHAT’S INSIDE YOUR SPA ....................................................................................................................................................................... 11

WHAT'S UNDER YOUR SPA (THE EQUIPMENT) ........................................................................................................................................ 16

START-UP ................................................................................................................................................................................................. 18

MP3/BLUETOOTH READY SYSTEM OPERATION ....................................................................................................................................... 21

BBA-BLUETOOTH AUDIO USER GUIDE ..................................................................................................................................................... 22

MAINTENANCE ......................................................................................................................................................................................... 27

FILTER SYSTEM ......................................................................................................................................................................................... 30

ACCESSING FILTER CARTRIDGES .............................................................................................................................................................. 30

DRAINING YOUR SPA ............................................................................................................................................................................... 31

WINTERIZING YOUR SPA .......................................................................................................................................................................... 32

TROUBLESHOOTING YOUR SPA ............................................................................................................................................................... 33

WATER TREATMENT GUIDE ..................................................................................................................................................................... 41

DOC: OM-A-2017-EN

Leisure Manufacturing Inc. 2017 Owner’s Manual

CONGRATULATIONS ON THE PURCHASE OF

YOUR NEW SPA

We have tried to compile a complete, easy to understand manual all about your spa and its' maintenance.

Years of research and development have gone into producing the superior quality product you have purchased. Your spa is made from the highest quality material and latest technology available today. Pride and meticulous attention to detail have resulted in the spa you have chosen. With proper care, your spa will provide many years of comfort and pleasure.

Please take a few minutes now to read all of the instructions before you install your spa. This owner's manual will help you understand your spa, so you will get the most from your investment. For service and advice, do not hesitate to call your authorized dealer. Your questions will be welcomed by friendly and knowledgeable staff.

May you have as much pleasure and enjoyment using your new spa, as we had making it for you.

We understand there are many choices in the marketplace when you are considering adding a spa to your home, so thank you for choosing a spa by

Leisure Manufacturing Inc. Enjoy!

SAFETY SIGN

IMPORTANT NOTICE: SAFETY SIGN

Enclosed with this Owner’s Manual is a Safety Sign. This sign must be permanently installed in a location that is visible to all spa users. It is the spa owner’s responsibility to remind all users about safe spa use, particularly occasional users of the spa, who may not be aware of the various health and safety issues.

To obtain additional or replacement copies of the safety sign, contact your dealer.


DOC: OM-A-2017-EN

3

ATTENTION: SPA OWNER

In the immediate vicinity of the spa, a sign must be posted stating the following:

1) The spa’s address

2) Location of the nearest telephone with posted emergency numbers

3) Nearest available police department, fire department and ambulance/rescue unit

CONDITIONS OF WARRANTY AND CONSUMER OBLIGATIONS

As a new spa owner, you have specific obligations in regards to the installation and safe use of this spa. Failure to do so may result in a loss of warranty coverage not to mention personal injury to those using this spa.

Inspect the spa upon its arrival for damage. If you are being made aware of this for the first time, your spa may not have been delivered in its original factory packaging. If this is the case, please take time to inspect your spa and report any damage or missing items to your dealer.

1) Install the spa both physically and electrically, in accordance with any local codes.

2) Provide suitable access to all sides of the spa. Any custom built enclosure, either above or below a deck surface, must be able to be removed with relative ease.

3) Provide sufficient work area around the spa’s perimeter especially the side the spa’s equipment is located on.

4) Regularly check operation of the spa in regard to filtration, jet pump operation and the heating system.

5) Report any concern to the dealer. Any problem that arises towards the end of particular warranty coverage should be documented and reported to the dealer

6) Maintain the water’s chemical balance and clean/replace the system’s cartridge filter(s) as instructed by the dealer and/or Leisure Manufacturing Inc.

7) Drain and refill the spa on a regular basis as instructed by the dealer and/or Leisure Manufacturing

Inc.

8) Winterize and store the spa and its’ components in accordance with the manufacturer’s printed instructions.

9) Care for and maintain the spa cabinet, hard cover and acrylic surface as outlined in these instructions.

10) Ask your dealer to record the spa’s serial number on your bill of sale.

11) Provide a copy of your bill of sale, if requested by the dealer or Leisure Manufacturing Inc.

4

DOC: OM-A-2017-EN


YOUR PERSONAL SPA DATA

Before you begin the installation of your new spa please take a few minutes to fill out the details of your spa. This information will become invaluable later should you have a question for your dealer or should you need to make a warranty claim. Ask your dealer to assist you in recording this information.

Model Year

Model Name/Number

Spa Serial#

Jet Pump(s) Size (HP, SPL, Watts etc.)

Heater size (kw)

Filter Cartridge (Model Number/Size)

Topside Control/Keypad

Spa Pack Model #

Spa Pack Serial #

Dealer Name

Date of Purchase

We strongly recommend that you attach your bill of sale to this manual after installation is complete.

Keep it in a safe place for future reference. You may also wish to attach any notes you have made about the dealer delivery, dealer start up demo or any other notes that may be of benefit in the future.


DOC: OM-A-2017-EN

5

IMPORTANT SAFETY INSTRUCTIONS

WARNINGS

DANGER: Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by children. To avoid accidents, ensure that children cannot use this spa unless they are supervised at all times.

DANGER: Risk of Injury. The suction fittings in this spa are sized to match the specific water flow created by the pump. Should the need arise to replace the suction fittings or the pump, be sure that the flow rates are compatible.

Never operate spa if the suction fittings are broken or missing. Never replace a suction fitting with one rated less than the flow rate marked on the original suction fitting.

DANGER: Risk of Electric Shock. Install at least 5 feet (1.5m) from all metal surfaces. As an alternative, a spa may be installed within 5 feet of metal surfaces if each metal surface is permanently connected by a minimum 8 AWG (8.4mm

2

) solid copper conductor to the wire connector on the terminal box that is provided for this purpose.

DANGER: Risk of Electric Shock. Do not permit any electrical appliance, such as a light, telephone, radio, or television, within 5 feet (1.5m) of a spa.

WARNING: To reduce the risk of injury: a) The water in a spa should never exceed 40°C (104°F). Water temperatures between 38°C

(100°F) and 40°C are considered safe for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes. b) Since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to 38°C (100°F). c) Before entering a spa, the user should measure the water temperature since the tolerance of water temperature-regulating devices varies. d) The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with the possibility of drowning. e) Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system problems or diabetes should consult a physician before using a spa. f) Persons using medication should consult a physician before using a spa since some medication may induce drowsiness while other medication may affect heart rate, blood pressure, and circulation.

CAUTION:

Maintain water chemistry in accordance with the manufacturer's instructions.

6

DOC: OM-A-2017-EN


READ AND FOLLOW ALL INSTRUCTIONS

When using this equipment, basic safety precautions should always be followed. Including the following: a) A green coloured terminal or a terminal marked G, GR, Ground, Grounding or the international grounding symbol is located inside the supply terminal box or compartment. To reduce the risk of electric shock, this terminal must be connected to the grounding means provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying this equipment. b) At least two lugs marked "BONDING LUGS" are provided on the external surface or on the inside of the supply terminal box or compartment. To reduce the risk of electric shock, connect the local common bonding grid in area of the hot tub or spa to these terminals with an insulated or bare copper conductor not smaller than No.6 AWG. c) All field-installed metal components such as rails, ladders, drains or other similar hardware within

3m (10ft) of the spa or hot tub shall be bonded to the equipment grounding bus with copper conductors not smaller than No.6 AWG.

DO NOT connect your spa to an extension cord.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

HYPERTHERMIA

Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 37°C

(98°F). The symptoms of hyperthermia include drowsiness, lethargy, and an increase in the internal temperature of the body. The effects of hyperthermia include:

•

Unawareness of impending hazard

•

Failure to perceive heat

• Failure to recognize the need to exit spa

•

Physical inability to exit spa

•

Fetal damage in pregnant women

• Unconsciousness and danger of drowning

WARNING:

The use of alcohol, drugs or medication can significantly increase the risk of fetal hyperthermia.


DOC: OM-A-2017-EN

7

8

IMPORTANT SAFETY INSTRUCTIONS FOR

SPAS WITH AUDIO SYSTEMS

CAUTION: Risk of Electric Shock. Do not leave compartment door open.

CAUTION: Risk of Electric Shock. Replace components only with identical components.

Do not operate the audio/video controls while inside the spa.

WARNING: Prevent Electrocution. Do not connect any auxiliary components to the system

(example: cable, additional speakers, headphones, additional audio/video components etc).

These units are not provided with an outdoor antenna. When provided, it should be installed in accordance with article 810 of the National Electrical Code, ANSI/NFPA 70.

Do not service this product yourself as opening or removing covers may expose you to dangerous voltage or other risk of injury. Refer all servicing to qualified service personnel.

If the power supply connections or power supply cord(s) are damaged; if water is entering the audio/video compartment or any electrical equipment compartment area; if the protective shields or barriers are showing signs of deterioration; or if there are signs of other potential damage to the unit, turn off the unit and refer servicing to a qualified service personnel.

This unit should be subjected to periodic routine maintenance (example: once every 3 months) to make sure that the unit is operating properly.

DOC: OM-A-2017-EN


INSTALLATION INSTRUCTIONS

Remember, your new spa is a powerful piece of electrical and plumbing equipment. You owe it to yourself, your family and your friends to install it correctly and safely. Before attempting to hook-up or use your spa, please read the following instructions.

POSITIONING OF YOUR SPA - CONSIDERATIONS

Your spa is completely self-contained. Therefore, you can situate it just about anywhere; on a patio, in or on a deck, in a basement or sunroom. It comes completely pre-plumbed and water tested from the factory. Never lift or carry the spa by the plumbing. Damage could occur which would not be covered under warranty.

You should take into account the following when selecting prospective spa sites in order to maximize enjoyment.

To avoid any personal injury or damage to your spa, have 4-5 people ready to assist you to move the spa to its' final location. Use a moving dolly and/or straps to more evenly distribute the spa's weight. Never lift or carry the spa by its' plumbing.

SITE CONSIDERATIONS

Local codes Local building, property and electrical codes may affect your installation.

Delivery access to location

Vegetation in spa area

Gates, overhangs, fences, gas meters, and AC units may become obstructions. You may need to access from a neighbour's yard or employ a crane.

Trees, bushes, flowers etc. can all add to spa maintenance.

Spa location relative to buildings

Fences, tree lines

Spa step out location

The location could add to your spa maintenance (removing snow from cover) and increase operating costs.

More privacy during use and serves as a wind break but may also add more maintenance.

Any surface that is slippery when wet could be dangerous for bathers both entering and exiting the spa.

Spa Direction View when using a lounger & ease of access for servicing.

Downspouts and natural drainage of land

Outside water supply and draining location

These may flood the spa area, damage spa or create a safety hazard to bathers.

You will need a place to safely drain the spa and a way to refill it easily.

Optional accessories

These may take up added space that you must plan for (cover remover/holder).

SPA SUPPORT

Whatever the support is, it must be: a) A continuous, level surface, above grade, capable of handling 80 lbs. per sq. ft. that will not be compromised by changes in the water table or water sitting in the area. b) Such that the weight of the spa, water and bathers is not supported by the spa lip. c) In full contact with the bottom of the spa


DOC: OM-A-2017-EN

9

ACCEPTABLE SPA SUPPORT BASES

Concrete Pad

Patio Stones, Pavers etc.

Wooden Deck Floor

4" to 6" thick with provision for run off

Levelled with proper preparation of the earth

Incl. centre support uprights in concrete and joists spaced 12" on centre

Engineered Plastic Spa Pad Following pad manufacturer's instructions

Unacceptable Spa support bases include crushed gravel, stone dust, bare earth, platform built directly onto earth. Damage caused by improper spa installation will void factory warranty.

Do NOT locate your spa in a low run-off area since melting snow or rain can cause pump and equipment damage. WATER SHOULD ALWAYS DRAIN AWAY FROM THE SPA.

See “Part B – Your Specific Spa’ for dimensions that can be used to determine the proper location of submerged conduits in concrete slab installations. All dimensions are made from the outside of the spa's frame with the access panels removed.

10

DOC: OM-A-2017-EN


WHAT’S INSIDE YOUR SPA

HYDROTHERAPY JETS

A variety of jet sizes and internal styles are used in unique seating patterns to achieve superior hydrotherapy in individual spa models. Therefore, not every jet described or pictured below is in every model. Not all jet internal styles are available in all jet sizes.

To adjust the water volume, simply turn the jet face clockwise to the off position or counter clockwise to the maximum position. If you move too hard to maximum you will release the internal from the jet body.

Jet Type Size

Adjustable

Flow

Where it is most often used

Ozone 1 ½” (38mm) No Seat backs, neck & shoulders, palm jets

Air-X 2” (51mm) No Specialty seat backs

Cluster

Mini

Poly

2 ¼” (56mm) Yes

3

5

/

16

” (84mm)

Yes

3

4

⅝

” (92mm)

⅜

” (105mm)

Yes

5 ¼” (133mm) Yes

Palm jets, loungers, seat backs, calves, neck collars

Seat backs, footwells, loungers

Seat backs, footwells, loungers

Power Seat backs, footwells, loungers

Master Massage 7 ½” (191mm) Yes Footwells

Foot Domes

Many of our larger models have unique foot domes that provide soothing therapy for your tired and aching feet. The dome gives us the chance to provide foot massage to several seating areas at the same time.


DOC: OM-A-2017-EN

11

Nozzle Type

Fixed Stream

Air-X

Hydrotherapy Effect Description

A steady, non-adjustable stream of water.

A soft tissue therapy jet. Draws up to 3x the air of a standard jet. Double, triple or multiple streams of air & water mixed for soothing comfort. Non volume adjustable.

Neck Jets

100% shut off by using the stepped down/up movement of the face to move volume nozzle in/out

Directional

Rifled

A steady volume adjustable stream of water with adjustable nozzle direction

A volume adjustable stream of water that gives the feel of a rotating stream of water without moving parts.

A volume adjustable jet with a fixed split nozzle that uses the water flow to deliver dual streams of water in a rotating pattern.

Twin Roto

12

A volume adjustable stream of water that rotates.

The combination of the moving inner mechanism and front face gives an ever changing pattern to the massage.

Massage

DOC: OM-A-2017-EN


Most often powered by itself from a single pump via a diverter valve. This jet produces a tidal wave sensation in the footwell and upwards to the water surface.

Master Massage

OTHER INTERNAL FITTINGS

Return Fitting (Models with Circ Pump only)

The return fitting is simply a wall fitting through which filtered and heated water return to the spa. Never block this fitting with any part of your body.

Suctions

These multi-holed, anti-vortex fittings in the footwell provide the intake water for the pump(s). A powerful suction is produced here when the jet pumps are turned on. On systems with a circulation pump, the bypass suction fitting (smaller than regular suction), may have little to no suction on it, since the circulation pump has a lower flow than the jet pump and the suction is only active as the filter(s) become clogged.

All suctions in our spas are VBG compliant for your safety.

Perimeter LED Lighting

These round or hex shaped, multi-faceted fittings, located on the vertical spa wall and deck of the spa, are the lenses for the LED light outputs.

Air Injectors (Models with Air Blower option)

These gently domed fittings are located in the bottom of the seats and are designed to diffuse the air, provided by the air blower, into tiny bubbles to enhance the spa experience.

Air Blower system with Aromatherapy Canister

(Models with Air Blower option)

The Aromatherapy system works automatically whenever the air blower is activated. A wonderful fragrance will fill the spa area adding to the overall spa experience.

To add beads to the canister:

Locate the canister on the deck of the spa Make sure the air blower is off before removing the cap Place beads inside the canister Replace cap Turn on air blower and enjoy!

A random trial package is included with the original Owner's Manual. Ask your dealer for refills of aromatherapy beads.


DOC: OM-A-2017-EN

13

Skimmer/Filter

This is the housing for your cartridge filter(s) and provides skimming action to remove surface debris.

Some models have a removable basket from which debris can be dumped.

Teleweir

Whitewater

(Sunrise)

DECK CONTROLS

Wave

Whitewater

(Paragon)

XL

Elite

Diverter Valves

These wave handle valves are used to direct water flow between 2 groups of jets.

You can choose 1 group independently or mix between the 2 groups. We

recommend you shut off the jet pump before changing the valve setting.

Wave

Air Controls

Located on the deck of the spa, these valves control the amount of air being mixed with the water stream at each jet. The minimum to maximum movement is approximately ¼ turn or on/off for toggle type. More air will increase the massage effect from the jet. Proper air draw is achieved when the jet pump is operating on high speed, particularly if the pump is a 2-speed pump.

On/off Water Valve

This positive seal valve is used to turn the water feature on/off. Adjust it as needed to achieve the best effect from the water feature.

Wave

WATER FEATURES

LED Waterfall

The LED waterfall located on a flat along the inside of the spa creates a relaxing sheet of water when turned on and adjusted using the on/off valve. When the

Light key is pressed LEDs light up the waterfall body as well as the water sheet coming out of the waterfall.

LED Pop Up Waterfall (Aqua Fan)

This unique water feature uses the flow of water to lift the top cover when the waterfall valve is opened. When the waterfall valve is closed the cover drops back to its' rest position slowly. The pop up waterfall is also LED ready so when the LED lights are turned on the fitting will take on the colour of the LED system.

14

DOC: OM-A-2017-EN


WATER FOUNTAINS

Located along the deck of the spa, these water features create a water rope effect into the spa when turned on.

LED POP-UP WATER FEATURE (AQUA BUBBLER)

When the waterfall valve is opened this water feature pops-up and a mini geyser of water comes out of the top. It then cascades over the top “shade” & forms the geyser effect. Used to trickle water over built in terraces in the spa shell.

MISCELLANEOUS

LED Spa Light

This clear or slightly bluish fitting is usually in the vertical surface of the spa steps. It is controlled by a designated switch on the keypad. It serves as a safety feature; lighting the spa's contours for those entering or exiting the spa.

Head Cushions

The many head cushions you will find in our spas are designed to add comfort to your spa experience.

Whether it is just to rest you head as you sit back and enjoy the hydrotherapy or if it is to support your neck as you let our neck collar jets soothe your aching neck and shoulders, you'll find all our head cushions functional and comfortable.


DOC: OM-A-2017-EN

15

WHAT’S UNDER YOUR SPA (THE EQUIPMENT)

The spa's control pack, circulation pump, heater, drain connection and ozonator may be accessed by removing the cabinet panel along the control side of the spa. Removing the panel(s) to the right or left of the spa's main access panel will allow access to the jet pumps, blower and any other optional equipment. On some models, all equipment is accessible from the main access panel.

The free standing spa pack houses the receptacles and switching apparatus (circuit board) for the pump(s) blower, light, keypad etc., as well as the heat regulating system. The spa pack is also where the electrical supply connections are made. The horizontal heater is attached to the bottom of the spa pack.

2-Speed Jet Pump

A high performance 2-speed jet pump provides the power to operate the various hydrotherapy jets in the spa, at the optimum level. On models without a circulation pump, the low speed of the pump is used to circulate the water so it can be filtered and heated. Some models may have a 2 nd

jet pumps to properly power the jets. Gate valves in the plumbing lines allow easy servicing of the circ pump and heater. Safety clips on the valve shafts keep the valves open during use.

Circulation Pump

The high efficiency, space saving circulation pump slowly moves water through the filter system, across the heater element and then back to the spa via the return fitting.

Air Blower Pump

The quiet air blower pumps air to the air manifold creating a "champagne" bubbling effect from the air injectors inside the spa. The air passes through an aromatherapy canister first, eroding the scented beads that are inside the canister.

Ozonator

An ozonator is used to assist in water treatment. The corona discharge (CD) model produces ozone which is drawn into the spa water via the return plumbing.

03/UV Sanitizer (AquaNova)

This unit creates both ozone and UV in perfect synergy to sanitize the spa water. Ozone introduced into the unit’s chamber reacts with the UV light to create hydrogen free radicals for advanced oxidization potential (AOP). This results in only oxygen bubbles emerging from the dual return fittings.

16

DOC: OM-A-2017-EN


Microsilk Pump

This optional high pressure jet pump in conjunction with a patented plumbing system creates a “cloud” of small, micro bubbles in the spa.

These micro bubbles help open your pores to invigorate both your body and senses. Microsilk runs independently from the rest of your spa. See the separate Microsilk instruction sheet, in your Spa Owner’s Packet, for complete details on how to operate this unique pump.

Other items under your spa may include an audio power supply, audio receiver and LED control system.


DOC: OM-A-2017-EN

17

START-UP

HOW YOUR SPA WORKS

Circulating, Heating and Filtering

Dedicated 24/7 circulation pump or low speed of a 2 speed pump (depending on model).

Immersion heating element within a stainless steel heater barrel.

Filter System

Single or two-cartridge system that is accessible from inside the spa.

Your spa may be equipped with a split filter system. One cartridge on jet pump 1 and the other on the circ pump. The clean-up cycle of the spa pack turns pump 1 on 30 minutes after you have shut it off or it times out. It will run for 30 minutes to help clean up the spa. This clean-up cycle is adjustable in 30 minute increments up to 4 hours.

Some topside controls, such as TP600, will not show a clean-up cycle adjustment, unless the set up number used is the one being used within the standard menu feature as opposed to the simplified menu.

Contact your dealer to get the setup number changed. See also Clean-up Cycle, within the TP600 User

Guide with Standard Menu feature, located in the Part B manual. See page 40-41 on how to change the clean-up cycle.

Hydrotherapy

A combination of up to three (3) single or 2-speed jet pumps provides a gentle, low-speed therapy or intense, high-speed therapy. The jets have directional nozzles, multiple directional nozzles, fixed nozzles or rotating nozzles. Most of the jets have the ability to have the water volume adjusted to your therapy needs.

Deck Controls

Air controls mix air with the water stream coming out of the jet. A diverter valve is used on some models to dedicate pump flow to specific groups of jets or share it amongst several jets. Models with the waterfall feature have a control valve to turn the waterfall on/off.

A digital topside control panel allows you to activate the pumps, blower and light plus set the temperature that you want the water to be. The topside display also shows error messages and tells you if any special spa pack features are operating, including protection against overheating and freeze-up.

Champagne Air Bubbler

The blower feature uses a high output air pump to send air through the water via shower head injectors.

18

DOC: OM-A-2017-EN


Lighting

Your spa is equipped with a multi-LED spa light allowing you to enjoy the effects of a colour changing LED light system. LED lights around the perimeter of the spa create a special effect of colour changing lights.

LED Light Operation

Your spa may be equipped with an LED light system consisting of perimeter lights, lighted water feature(s), lighted jets and a thru wall underwater spa light, depending on the spa model and options. The system is controlled using the LIGHT key on the topside control panel. The spa pack is factory set/programmed for simple on/off spa light operation. Note that not all colours are available on all LED systems.

Operation: To move from setting to setting simply turn the LIGHT key on/off.

If the light is turned OFF for more than 5 seconds, the sequence automatically restarts at the last colour shown.

Light Sequence (Ultrabrite System)

Slow Cycle

White

Aqua

Magenta

(Blue, Green and Red mix)

(Blue and Green mix)

(Blue and Red mix)

Blue

Gold

Green

Red

Flash

Strobe

(Red and Green mix)

Light Sequence (Sunlite or Glo LED Jets Feature/Option Where Available – Lighted Jets)

The Sunlite System uses a special MZ controller that has a unique colour sequence.

Colour Wheel (Slow fade from colour to colour)

Green

Aqua

Magenta

Blue

Red

Colour Jump (A fast change from colour to colour)


DOC: OM-A-2017-EN

19

FILLING YOUR SPA

Okay, your new spa has been connected to the power and you have a basic understanding of how the equipment works and what the jets can do for you. We know you are anxious to fill the spa and get it started, but please read this section carefully before you fill your spa.

1) Make certain that the breaker or fuse(s) that supplies your spa equipment is off.

2) Wash the spa surface thoroughly with warm water and a soft cloth only to remove any construction or transportation debris.

3) Check that the drain connection is closed.

4) Check that the unions on the spa pack and pump(s) are tight. They can loosen during transportation.

5) Remove the filter cartridges.

6) Begin filling the spa with a standard garden hose. Do not fill your spa with soft water (consult dealer). If possible, your source fill water temperature should not be less than 70°F (21°C). Do Not operate the spa with low water levels. A level 4" over the bottom of the skimmer mouth is recommended. Maximum initial water level should be 6” below the spa lip. Adjust as needed based on number of bathers using the spa. Consider adding an overflow to your spa if you are regularly having enough bathers in the spa to significantly raise the water level such that damage to equipment may occur.

7) Increase the fill pressure slowly to prevent surface damage by a jerking hose.

8) Visually check all lines for leaks and correct immediately. If you cannot stop the leak simply by tightening a union or resetting an "O" ring or gasket, contact your dealer immediately.

9) Turn on the main power at your electrical panel.

10) The topside control panel will initialize and begin its’ start-up procedure. Then the system will start the circulation pump(or low speed pump) and the heater.

11) Re-install the filter cartridges.

IMPORTANT: Now, read about the keypad operation, user settings, system defaults, automatic functions and display messages included in this manual (see User Guide in the Index). Take a few minutes to try the various keys and features on your new spa. For your convenience the

User Guide is located at the end of Part B of this Owner’s Manual.

Once you feel comfortable with the operation of your spa's controls, set the temperature to the desired level (100°F/38°C is an excellent starting point). Close the air controls and cover the spa with your hard cover. Heat up times will vary based on volume of water in the spa, but you can generally expect 6-8 hours to reach maximum temperature. Spas running on 120VAC will have a longer initial heat-up time.

Always view the temperature display before entering the water. For your own personal safety, do not enter when the temperature exceeds the maximum set point of 40°C (104°F).

20

DOC: OM-A-2017-EN


MP3/BLUETOOTH READY SYSTEM OPERATION

The MP3/Bluetooth ready system will work with any digital audio player or any audio source whose output

(usually headphone jack) can be adapted to the 3.5mm stereo cable

MP3 Operation:

1. Plug one end of the3.5mm stereo gold plated cable (provided in the Owner’s manual packet) into your

MP3 player or other portable media.

1. Turn on the power switch (upper switch) in the dock. The red indicator light will be on.

2. Turn MP3 player on.

3. Note: If the “BT” switch is on, you will not be able to play music via the 3.5mm connection.

4. If MP3 player or other audio source has bass/treble settings or equalizer settings or music genre EQ settings adjust these to desired levels.

5. Depending on the size of your MP3 player you may be able to put it inside the dock and close the door.

The quality of the MP3 player being used and the downloaded audio files on the MP3 player may effect the overall sound quality of the MP3 system on the spa.

Bluetooth Operation:

If your audio player has Bluetooth capabilities, you may find it easier to stream audio to the subwoofer/amp system, especially if the audio player is larger than the dock.

1. Turn on the power switch (upper switch) in the dock. The red indicator light will be on.

2. Turn your audio device on.

3. Turn the “BT” switch below the power switch to “ON”. You will hear a beep tone indicating the

Bluetooth system is ready to be activated.

4. Go to “settings” on your audio player and select “Bluetooth”.

5. The audio player should start searching for Bluetooth devices.

6. Once it locates this Bluetooth system, it should show “Blue Audio” and begin to connect to it.

7. If your audio player requires a code to connect to the Bluetooth subwoofer/amp, enter “0000”.

8. Bluetooth should complete its’ connection and show you that Blue Audio is now connected.

9. Now when you go to your audio files or other audio programs such as an Internet radio player, the sound will be streamed to the subwoofer/amp.

10. In some cases you may need to direct the audio player to play the sound to the device or to Blue

Audio.


DOC: OM-A-2017-EN

21

22

DOC: OM-A-2017-EN



DOC: OM-A-2017-EN

23

24

DOC: OM-A-2017-EN


BLUETOOTH CONNECTION

1) Press AV on spaTouch display

2) Turn on the amplifier (PWR Button), spaTouch displays shows “Powering Up”

3) Turn on Bluetooth function of your mobile or music device

4) On your music device, click search for Bluetooth device. Make sure you are close enough to the amplifier. SpaTouch display shows “Discoverable”

5) Select “PPGME60” from the pairing list

6) Enter “6000” as the password (if required)

7) Click “Connect”. SpaTouch display shows “BT Connected”

8) Once connected, you can now start playing your favourite music from your music device

9) Operating Range is up to 30’ (will vary, dependent on installation)

LINE INPUT CONNECTION:

This unit can be connected to any portable music devices such as MP3 Player, TV and DVD through the

LINE INPUT. Press LINE INPUT button to change the mode to LINE INPUT (Line In or Direct light indicator should be on and red).

Please note: In this mode, all controls and functions must be controlled from your music device. Line input cannot be used in standalone mode.


DOC: OM-A-2017-EN

25

26

DOC: OM-A-2017-EN


MAINTENANCE

To protect the equipment and the bathers using your spa, regular maintenance must be performed.

CARING FOR THE ACRYLIC SURFACE

This beautiful acrylic surface is among the glossiest, high quality surface materials available. It's hard, non-porous surface prevents dirt from accumulating and resists stains better than other plastic materials.

With normal use, it is so durable it will retain its beauty with only a minimum of care. So to maintain the high gloss and elegant look, just follow these simple steps:

•

Use common household, non-abrasive cleaners for most cleaning jobs.

(For example: LYSOL BASIN, TUB & TILE CLEANER, GLASS PLUS, MR.CLEAN and TOP JOB, or a mild dishwashing detergent such as IVORY LIQUID) Rinse well and dry with a clean cloth.

•

Never use abrasive cleaners.

•

Do not allow your acrylic surface to come into contact with products such as acetone (nail polish remover), nail polish, dry cleaning solution, lacquer thinners, gasoline, pine oil, etc.

•

Remove dust and dry dirt with a soft, damp cloth.

•

Clean grease, oil, paint and ink stains with isopropyl (rubbing) alcohol.

•

Avoid using razor blades or other sharp instruments that might scratch the surface. Small scratches can be removed by applying a thin coat of automotive paste wax and buffing lightly with a clean cloth. For deeper scratches, sand the surface lightly with 600 grit "wet" sandpaper (never dry) and buff with fine-grit buffing compound.

If you don't rinse off any surface cleaner thoroughly, you will experience excessive foaming on refilling and start-up. Periodic application of a good wax adds lustre to the appearance and protects the finish.

CLEANING THE SPA'S CABINET

Cleaning the cabinet is easy and fast with many common household cleaners. The cleaning solution should be applied and immediately wiped dry. The cleaning solution should not be left to stand on the material for an extended period of time.

Recommended Cleaners:

Windex, Glass Plus, 409 Glass & Surface Cleaner, Spic and Span Cinch, Fantastik All-Purpose, Regency

(Glass & Surface), Clorox Clean-Up and Fantastik Orange Action

Cleaners to avoid:

Harsh cleaners with glycol ethers or ethanol type solvents and/or isopropyl alcohol soften the coating if left on for several minutes.

Cleaners such as Goof Off, Great Value All Purpose Cleaner (Wal-Mart), 409 General Purpose, Greased

Lightning, citrus cleaners, abrasive cleaners and solvents such as acetone, paint remover and lacquer thinner are NOT recommended for cleaning the cabinet.


DOC: OM-A-2017-EN

27

SPA HARD COVER

In an uncovered spa, over 90% of the heat loss is from the spa surface. The evaporation also affects the chemical balance and could create humidity problems indoors.

Hard covers are engineered for maximum thermal efficiency and appearance. They are hinged in the middle for easier handling, and the zippers allow the tapered styrofoam inserts to be changed if damaged.

The skirt on the cover hugs the lip of the spa for a tight fit. The handles are placed so even a large cover can be easily opened by 1 person.

The locks, with one part fastened to the deck or skirt, prevent small children or animals from entering the spa.

• Do not drag the cover across the spa or decking. Fold cover first, and then remove with assistance.

• Do not place the spa where snow loads are excessive on the cover. If snow accumulates on the cover, carefully remove the snow.

• Do not shovel the snow as the cover will tear.

• Do not stand on the hard cover. The cover is not warranted against the foam breaking or the vinyl cover tearing.

• Do not use abrasive cleaners or leather restoration-type cleaners. Use only water and a mild detergent.

JET MAINTENANCE

Several of the jets in your spa are volume adjustable. The volume adjustment of the jet internals in these jets can be effected by debris in the spa water. If you feel the volume adjustment getting stiff, you should consider removing and washing the internal at the next scheduled fill and drain of the spa.

To remove an adjustable jet internal:

1) Turn the jet face to the maximum volume position (fully counter clockwise).

2) The jet face will feel as if it has stopped but if you continue to turn the face, the jet internal will thread out of the body.

3) Check the inside of the jet body and the internal for any debris and calcium build up.

4) Wipe out the inside of the jet body, if necessary.

5) Wash the internal in your service sink. Scrub, gently, if necessary.

6) To re-install a jet internal simply thread the internal in until it stops. Now continue turning until the internal locks into its volume adjustment range.

If you find high levels of calcium build up or any discolouration of the jet internal when removed, you should take a spa water sample to your dealer for testing.

28

DOC: OM-A-2017-EN


DIVERTER VALVE MAINTENANCE

If your spa has a water diverter valve, it is important that you conduct regular maintenance on it to ensure that it continues to move freely and does not begin to leak. The best time to do this maintenance is when you are doing a drain and refill.

1) If you unthread the cap (2), you can remove a number of parts that make up the moving assembly. These include the diverter (7), O ring (6), cap (2) and handle (l).The moving handle is only a hand press fit, so you can take it apart easily.

2) Examine the surface of the diverter (7). If it has any scratches or score marks on it, there is debris, likely dirt or sand getting into your spa. If you do not stop this from happening, eventually the valve will seize and you will break off the handle or worse. This type of damage is not covered under warranty.

3) Sand the diverter (7) lightly to remove the scratches. Clean out any debris inside the body (9).

From inside the spa you will only be able to see the inside of the body (9), the top threads and the body O ring (8).

4) Examine the body O ring (8). This O ring seals the cap (2) to the body (9). Remove any debris that could hinder it from sealing properly when reinstalled. Check for areas that are cut or pinched.

Pinched areas may be fixed by placing the O ring in hot water for a few minutes and then allowing it to cool down. Cut or broken O rings should be replaced.

5) If you remove the handle (1) and cap (2) from the moving assembly you took out, you will be able to see the O rings (6). Make sure these parts are there. They seal the shaft as it passes through the cap (2). Do the same inspection/replacement as you did for the body O ring (8).

6) If any of the O rings are dry or hard, you can use a small amount of silicone based lubricant to make them pliable again. DO NOT use Vaseline or any other petroleum based product on the O rings.

7) Reassemble the moving assembly and insert it back into the body (10). As you tighten the cap (2) move the handle (1) slightly to ensure that the cut-out on the bottom of the diverter(7) is lined up to the sidewall tab that is in the bottom of the body(9). You may want to look at these (2) areas for reference before you re-install the moving assembly.

8) Tighten the cap (2) hand tight only. On spa start up check the outer cap edge and inner handle for leaks. Reminder: Never adjust the diverter valve setting while the pump is running. This

puts stress on the internal parts of the valve and could cause breakage or leaking to

occur.


DOC: OM-A-2017-EN

29

FILTER SYSTEM

GENERAL INFORMATION

You will need to regularly inspect your filter cartridges to ensure they are clean.

As your cartridges get dirtier they could effect:

• Heating of the spa water: restricted water flow from a clogged filter can cause error codes to display on the control pad and prevent the spa from heating properly

•

Water quality: a change in function of the ozone injection system can result in a drop, or complete stop, of ozone draw into the spa water

Keeping a second set of cartridges and rotating out dirty ones for clean ones can help keep your water clean and sparkling, reduce chemical consumption and down time due to cartridge cleaning.

SPECIAL NOTE: Several replacement cartridges look similar. Using the wrong cartridge may cause problems. Ask your dealer for the code that identifies your cartridge and record it.

CLEANING FILTER CARTRIDGES

1) Remove large debris by separating cartridge folds and spraying with a stream of water. Your kitchen or laundry sink is useful for this.

2) Contaminants that cause the cartridge to become brownish or greyish in colour require soaking overnight in specially formulated cartridge cleaner (available from your dealer).

3) Use a large plastic pail and follow the package directions. For safety reasons, you should locate your soaking pail out of reach of children.

4) Rinse the cartridge thoroughly to remove all the cleaner.

5) Allow cleaned cartridge to dry completely before re-using.

6) Spread pleats and run a soft brush through each one individually to complete the cleaning process.

ACCESSING FILTER CARTRIDGES

See Part B –Your Specific Spa for information on accessing your filter cartridge.

30

DOC: OM-A-2017-EN


DRAINING YOUR SPA

KNOWING WHEN TO DRAIN

Dissolved solids from bather load and ongoing chemical treatment accumulate in your spa water. The early sign of a high level of dissolved solids is unmanageable cloudy water.

When in doubt, remember that the best chemical for your spa is fresh water!

HOW TO DRAIN YOUR SPA

1) Turn down the set point on your spa and allow adequate time for the water to cool down. Uncover and run high speed pump to speed up cooling.

2) Turn power off to your spa.

3) Attach the appropriate size hose to the drain connection (see below).

4) Route the hose to an appropriate drain location.

5) When the drain is opened the spa will gravity drain, even unattended.

6) As draining proceeds, move water from contours of seats, into the footwell. Draining will stop due to drain height.

7) Remove any remaining water with a shop vac, sponge and pail or simply dilute in your fresh fill.

8) Before refilling, clean spa surface as necessary.

9) Don't forget to close the drain before refilling.

If you want to speed up the draining process, simply use a submersible sump pump available through most hardware stores.

DRAIN CONNECTIONS

Hose Drain (Most Models)

Located in the equipment area, the flexible hose drain easily connects to a standard garden hose. After routing the garden hose to a suitable drain location, turn off the spa, then turn the valve handle to open the valve and start draining.


DOC: OM-A-2017-EN

31

Magic Drain (Paragon Models)

WHEN VACUUMING SPA LINES:

1) Vacuum at all suctions in the foot well. This could be 2-6 suction depending on the model.

2) Vacuum at the heater input (union and gate valve), usually on the left of the equipment side of the spa.

Make sure to vacuum until you feel no more water coming out, then block the 2 cartridge mounts or block the Elite or Teleweir opening.

Remove the cartridge(s). Thread plugs into the threaded cartridge mounts in the filter box. For Elite or

Teleweir filter system, remove the trim ring and weir. Cover the filter opening with rigid plastic and use something with weight to hold it down and vacuum again at the heater input.

This will help draw water out of any lines connected to the spa pack, especially for spas that do not have a circ pump.

WINTERIZING YOUR SPA

Cold climates, where danger of freezing exists, require special care on your part in order to prevent damage to the spa shell and equipment. If you plan to use your spa during the cold months, be sure your pump is running frequently enough to keep the water moving so that the heater will operate. It may be best to set your controls to keep the pump on low speed at all times. This will keep the water from freezing and the heater will come on as the temperatures drop.

32

DOC: OM-A-2017-EN


WARNING:

If you have a power outage, and cold temperatures are possible, your spa and equipment could freeze, especially if it is mounted in a deck without a cabinet. Ice in the spa and equipment will cause damage.

You should consider the need to have your spa professionally winterized if it is to be dormant for a period. This is especially true if you are taking an extended winter vacation.

Follow the procedure below to help prevent damage to your spa and related equipment:

1) Drain the spa of all water, as outlined in owner's manual. Shut off the spa's power supply.

2) Remove any remaining water with sponge. If you have a shop vac, try vacuuming as much water as possible out of the jets and spa shell. If you cannot remove all of the water (especially from the air injectors) RV style or plumbing system anti-freeze should be added to the injectors.

3) Remove spa equipment system and pump for storage inside. If this is not practical, use the shop vac again to draw any water from the pump(s) casings. Remove lower casing drain plugs. Add antifreeze to all pump housings. (see note below)

When vacuuming spa lines: a) Vacuum at all suctions in the foot well. This could be 2-6 suction depending on the model. b) Vacuum at the heater input (union and gate valve), usually on the left of the equipment side of the spa.

Vacuum until you feel no more water coming out, then block the 2 cartridge mounts or block the Elite or Teleweir opening

Remove the cartridge(s). Thread plugs into the threaded cartridge mounts in the filter box. For

Elite or Teleweir filter system, remove the Vane weir/trim ring and float assembly. Cover the filter opening with rigid plastic and use something with weight to hold it down. Vacuum again at the heater input.

This will help draw water out of any lines connected to the spa pack, especially for spas that do not have a circ pump.

4) The filter should be drained and cartridge removed and cleaned. Remove the filter cartridge and pour anti-freeze as mentioned earlier into the filter canister. Store the filter element in a room with above freezing temperatures.

5) Support the hard cover along the hinge with 2 by 4's across the spa. Lock your hard cover over the spa and cover entire spa with a tarpaulin. Block the tarp in place or staple to your cabinetry.

6) When you refill in the spring, remember to re-install any plugs that were removed. Follow the directions for start-up, as if this were a new spa.

Note: Any RV style or plumbing system anti-freeze used may leave behind a residue that could cause a white "fizz" in the first refill of water, especially when the jet pump(s) are turned on. You may need to drain and refill the spa to clear away the residue. During colder months of the year, plumbing

anti-freeze is added to all pump housings as part of our production procedures. This fact is noted on the outer spa packaging.


DOC: OM-A-2017-EN

33

TROUBLESHOOTING YOUR SPA

COMMON PROBLEMS AND HOW TO SOLVE THEM

NOTICE:

A large number of problems on start up can be attributed to mis-wiring and a poor understanding of how the spa operates and its' features. Take the time to read and understand this manual. If you have any questions contact your dealer.

GROUND FAULT CIRCUIT INTERRUPTER (GFCI) OR RESIDUAL CURRENT

DETECTOR (RCD) SHUTS OFF ON INITIAL START UP

Probable cause:

Mis-wiring of GFCI/RCD.

Action:

Contact electrician and/or dealer.

GROUND FAULT CIRCUIT INTERRUPTER (GFCI) or RESIDUAL CURRENT

DETECTOR (RCD) SHUTS OFF (NOT ON INITIAL START UP)

Probable cause:

Action:

One or more pieces of equipment is shorting to ground or total current draw exceeds

GFCI/RCD rating.

Contact dealer: DO NOT use spa. Take measures to ensure others do not use spa.

SPA IS COMPLETELY "DEAD" (NO CIRCULATION AND NO DISPLAY ON TOPSIDE

CONTROL PANEL)

Probable cause #1:

GFCI/RCD has tripped (shut off).

Action:

Reset GFCI/RCD and monitor for futures trips. Alert dealer if problem persists.


Breaker or fuse before GFCI/RCD is tripped or blown.

Action:

Shut off GFCI/RCD, reset breaker or replace fuse, reset GFCI/RCD and test. Contact electrician or dealer if problem persists.


Transformer fuse blown in spa pack.

34

DOC: OM-A-2017-EN


Action:

Locate fuse in spa pack, test and/or replace. Or contact dealer for service.


Insufficient line voltage to power up spa pack processor.

Action:

Contact electrician to measure line voltages and inspect supply connections.

NO HEAT OR HEAT TOO LOW


Set point is not at desired level.

Action:

Review set point and change if necessary.


Circ pump is not running or pumping.

Action:

Check if valves on circ pump/heater system are open (handle pulled up exposing valve shaft, safety clips should be in place to prevent valve closure). Check if circ pump is plugged in or if circ pump fuse in spa pack is burnt out.


Spa is not covered when not being used.

Action:

Cover spa to retain heat.


Heater is not on due to error message showing on display.

Action:

Check for open gate valves on equipment, correct low water level in spa, and examine condition of filter cartridge(s). Turn spa power off then back on. Monitor for reoccurring error message on display. Contact dealer if problem persists.


System Input current setting is restricting heater operation.

Action:

Consult dealer/electrician on system current setup and if a higher input current is available from the supply. This may mean rewiring the spa with a larger gauge cable and/or breaker.


Lack of insulation in a custom installation.

Action:

Protect underside of spa from prevailing cold winds or snow. Enclose custom installations.

JET(S) DO NOT COME ON WHEN PUMP KEY IS PRESSED


DOC: OM-A-2017-EN

35


Jet pump is not plugged into spa pack.

Action:

Plug pump in and test.


Jet pump fuse blown in spa pack.

Action:

Locate & test/replace pump fuse in spa pack. Contact dealer if problem persists.


Jet pump is not primed.

Action:

Shut off spa and allow trapped air to escape. Restart spa & check jet pump operation.

If problem persists bleed air at pump directly by opening union on pump until all entrapped air is released. Retest.


Individually adjustable volume jets are adjusted to low volume.

Action:

Turn face of specific jet to increase water volume.


Air control is closed. No visible air/water mix.

Action:

Open air control to increase air/water mix.


Pump has overheated and tripped internal thermal overload.

Action:

Wait for pump to cool & listen for "snap" sound as overload resets. Pump should restart. Contact dealer if problem persists.


Pump is not pumping due to broken part inside (motor works, pump is primed but there is no water movement from pump).

Action:

Contact dealer for service.

AIR INJECTORS DO NOT BUBBLE WHEN BLOWER KEY IS PRESSED


Air blower is not plugged in to spa pack.

Action:

Plug blower in and test.


Blower fuse blown in spa pack.

36

DOC: OM-A-2017-EN


Action:

Locate and test/replace blower fuse in spa pack. Call dealer if problem persists.


Air blower disconnected from blower plumbing.

Action:

View blower plumbing and reconnect if disconnected. Test.


Air blower has overheated and thermal overload has tripped.

Action:

Wait for blower to cool and reset. Re-test. Call dealer if problem persists.

LED LIGHT(S) DO NOT COME ON WHEN LIGHT KEY IS PRESSED.


Light fuse blown in spa pack

Action:

Locate and test/replace light fuse in spa pack Call dealer if problem persists.


In -line or on board fuse blown in LED controller

Action:

Locate and test/replace light fuse in LED control box.

NO AIR/WATER MIXTURE COMING FROM A JET


Air control is closed

Action:

Open air control


Water volume through jet is too low to draw air

Action:

Increase water volume by turning jet face


Adjustable jet internal is loose.

Action:

Tighten jet internal


Jet internal is broken or damaged

Action:

Replace jet internal with another one from the spa or with a new one.


DOC: OM-A-2017-EN

37


Debris inside the jet internal

Action:

Remove the internal, inspect for debris, remove debris and re-install. Test

HOW TO CHECK A FUSE

Note: You should only remove/check a fuse if you feel comfortable doing so. Do not risk personal

injury. If in doubt, contact your service technician.

Fuses are located within the wiring compartment. Always replace fuses with the same style and amp value as shown on the label inside the wiring compartment!

Small Glass Fuses

1) Shut off power to the spa.

2) Use a small screwdriver or pliers to gently remove the fuse from its fuse holder.

3) View the filament inside the fuse and replace if broken.

4) Use an ohmmeter to check the fuse. Ohms reading should be towards 0 ohms. A reading of infinity means the fuse is open and must be replaced.

Cartridge Fuses & Small Cartridge Fuses

1) Shut off power to the spa.

2) Use pliers to remove the fuse from its fuse holder.

3) Replace fuse and test system.

These types of fuses are available from your local dealer and may be available from local electronic stores and home centres. Each fuse has a voltage and amp rating listed on it and should be used to obtain a replacement fuse.

Note: A single fuse may protect more than 1 component in your spa.

WARRANTY SERVICE

38

DOC: OM-A-2017-EN


In the event that you require warranty service, please call the authorized dealer where you purchased the spa. Your dealer has trained service personnel and an obligation to provide you with excellent after-sales service. We conduct yearly training classes to update and refresh technicians.

BEFORE CONFIRMING A SERVICE APPOINTMENT

Have ready the serial number and model number/name of your spa, your date of purchase and store receipt. The spa model and serial number information can be found on the silver and black data plate attached to the lower right corner on the equipment side of the spa. It is also located on the Spa

Identification Sheet that is within a plastic bag stapled to the backside of the equipment panel.

BP501/601 Series Spa Packs

Includes: SR1BP501, SR2BP501, SR2BP501X, SR2BP601E

F4

F5

F6

“Typical Board Layout”

Fuse Size Protects

F2

F3

3A, 250V

10A, 250V

Ozonator

Blower (when connected to J14)

3A, 250V

30A

0.3A, 250V

Spa Light

Pump 1, Circ Pump, Audio, pump 2(when connected to J14)

Transformer


DOC: OM-A-2017-EN

39

BP2000/2100 Series Spa Packs

Includes: SRBP20, SRBP20X, SRBP20MS, SRBP21, SRBP21X, SRBP21MS

F3

F4

F6

F7

“Typical Board Layout”

Fuse Size Protects

F1

F2

30A

10A, 250VAC

Component(s) plugged into J1 on expander board

Typically Pump 2, Pump 3, Microsilk

Ozonator, Circ Pump

0.3A, S10-B10

3A,S10-B10

30A

10A, 250V

Transformer

Spa light

Pump 1, Audio

Blower (J14)

F8 30A Pump 2, Blower (J14)

Note: When system software set-up is such that blower is connected to Expander X-P332, the inline fuse in the AMP adapter is 10A, 250V.

40

DOC: OM-A-2017-EN


WATER TREATMENT GUIDE

HEALTH HAZARD:

THE WATER IN YOUR SPA MUST BE CHEMICALLY TREATED AND

MAINTAINED AT REGULAR INTERVALS.

Bacteria can enter your spa water through the fill source, the bathers, and the environment. It is the responsibility of the spa owner to chemically treat the spa water in accordance with the local standards. Cross contamination between bathers can occur.

Your dealer or local pool and spa professional can provide expert testing along with all the products you will need for clear, clean, healthy spa water. Follow their instructions.

Untreated water is not only uncomfortable to relax in; it poses a health hazard to all bathers and a safety hazard to the equipment.

Equipment and surface damage caused by poor water treatment and/or unbalanced spa water is not covered under warranty.

SANITIZING YOUR SPA

IMPORTANT: * Your dealer may be promoting a water treatment system that does not employ part of all of the general water care instructions below. This guide is designed to

give the spa owner a basic understanding of spa water treatment.* When in doubt, follow the recommendations of your dealer. It is recommended that you have your source water tested by your dealer or local testing agency before the first fill. Knowing the characteristics of your source water can help you maintain clean and clear spa water on a regular basis.

Do not allow any floating chemical dispenser to get drawn in and held in the skimming area.

Large amounts of chemical can become concentrated in one area and damage the acrylic surface. This type of damage is not covered under the warranty.

INITIAL START-UP

(Review chemical manual - if applicable)

Your spa has__________litres,__________gallons of water (please fill in).

1) When the spa is full, add a scale preventative to inhibit staining and scale formation.

2) Test and adjust alkalinity to level recommended by manufacturer, this stabilizes pH.

3) Circulate water for 24 hours.

4) Test the pH. The ideal range is 7.2 to 7.6. Adjust if necessary with pH Booster or pH Reducer.

5) Circulate the water for 30 minutes.

6) If you are using Organic Bromine (Bromine Tablets), adjust your dispenser so the bromine residual is 3 to 5 ppm. Lower bromine level may be possible with ozonator.


DOC: OM-A-2017-EN

41

7) Whenever adjusting spa chemicals, less is better. Add chemicals in small amounts over several days.

Does your spa have a Fresh Water Ozone system on it?

1) The Fresh Water Ozone System is very simple to monitor. Follow the procedures listed below to ensure continued clean, healthy water.

2) Using chlorine and a DPD test kit, measure Free Available Chlorine (FAC) and Total Chlorine (TC).

As long as the difference is less than 0.5 ppm, the powerful oxidizer from the Fresh Water Ozone system is entering your spa and cleaning your water. You will only need to add small amounts of chlorine to maintain a sanitizer.

3) Check your pH, total alkalinity and calcium hardness as recommended by your Sunrise Spa dealer, and adjust if required. Please note: With the Sunrise Fresh Water Ozone system, maintain a pH between 7.6 and 7.8.

4) Check the bubble mist entering the spa, via the dedicated ozone/return jet, for consistency. An irregular bubble mist could indicate a blockage in the pump or pipes, a dirty cartridge(s) , low water level or pump operation problems.

5) On an ultraviolet ozonator, check the glow fitting on the ozonator for a blue colour to ensure that the bulb is on. On a CD ozonator check that the ‘power on’ indicator light is on.

6) Disconnect the tubing from the glow fitting and place your finger over the end of the tubing to feel for suction. This will ensure that the bubble mist entering your spa is coming through the Sunrise

Fresh Water Ozone system.

REMEMBER: Your spa water cannot be treated if the circulation system is not operating. The longer the spa's circulation system runs, the cleaner your water will be. This is not a problem on spa with a dedicated circulation pump. However, on models that use the low speed of a 2-speed pump to circulate the water, the filter cycle should be no less than 4 to 6 hours per day.

42

DOC: OM-A-2017-EN


DAILY MAINTENANCE

To keep your spa water sparkling clear and odour free, follow these steps:

1) Spas with adjustable filter cycles should be operated a minimum of 8 hours a day to remove suspended particles that may exist.( 4 hours per a 12 hour period)

2) Test pH to maintain a level of 7.2 to 7.6. If an ozonator is being used, pH should be 7.8 while ozonator is working.

3) If you are using Organic Bromine (Bromine Tablets) adjust your feeder so the bromine residual is 3 to 5 ppm.

WEEKLY MAINTENANCE

When the spa is not in use:

1) Add 1 cap (30 mL) of a Scale Preventative per 250 gal (1000 Litres) to inhibit scaling and staining.

Circulate water for 30 minutes.

2) Add a Brightener 24 hours after adding the Scale Preventative. Circulate the water for 30 minutes.

3) With the bromine sanitizing system, contaminants may build up during the week. The spa should be shocked with a Spa Shock. This will eliminate any odour and restore clarity to the water.

PERIODIC MAINTENANCE

1) Greases, oils and organic waste can accumulate on the filter cartridge reducing their efficiency and limiting the effectiveness of the disinfectant. Clean the filter with CARTRIDGE CLEANER as directed.

Physically clean the filter basket daily (if applicable).

NOTE: It is not recommended to use muriatic acid on filter cartridges as this is a raw chemical which does not rinse out well, ending up back in the water causing low pH levels.

2) The use of the scum ball will cut down on grease, foam and suspended particles in the spa. The scum ball acts as a filter before the filter and will increase the life of the cartridge.

3) The use of a thermal insulated hard cover will reduce evaporation and heat loss. Keep cover on and level at all times when spa is not in use.

4) Once you have established a comfortable water temperature to soak at, leave the thermostat at that temperature. Rapid changes in water temperature consume more energy.

5) Take a sample of water to your dealer to test for alkalinity, calcium and total dissolved solids.

6) WHEN TO DRAIN SPA WATER. Due to the warm water temperature and high evaporation rate, the total dissolved solids tend to build up. For this reason we recommend draining and refilling the spa every 2 to 4 months - depending on usage.

7) Clean your filter(s) at least once every two weeks or after heavy bather loads, by soaking your filter(s) in cartridge cleaner. Dirty filters cause the heater to shut off or the spa temperature to drift lower than desired.

NOTE: Remove any objects floating on the water before removing skimmer basket and filter or they may be sucked into the pump.

NOTE: Spas should not be left running unattended without filters. Remove filters for cleaning. Always turn off the spa before removing the cartridge(s) Debris can enter plumbing and cause damage.


DOC: OM-A-2017-EN

43

CHEMICAL SAFETY TIPS

READ THE DIRECTIONS CAREFULLY

1) Always add chemicals to water, never add water to chemicals.

2) Do not mix chemicals.

3) Store chemicals in a cool dry place - out of reach of children.

4) In case of contact or if chemical is swallowed, follow emergency advice on product label.

5) Do not smoke near chemicals. Keep the container closed when not in use.

WATER BALANCE

Water balance is important to the overall performance of your spa. No 2 spa's water conditions are exactly alike. The water source, location of the spa and frequency of use all effect the water balance. Unbalanced water can damage the equipment, especially the heater element, make the water uncomfortable for the user, and decrease the effectiveness of the disinfectant. Total alkalinity, pH, and calcium hardness must be within the correct range to balance the water. Damage to equipment caused by improper water chemistry is not covered by warranty.

pH

Simply pH is a scale indicating whether spa water is basic, neutral or acidic. Spa water should be slightly basic 7.2 to 7.6; 7.8 with an ozonator in operation. A low pH below 7.2 leads to corrosion of spa equipment and will irritate the skin of the bathers. The sanitizer will dissipate more rapidly. A low pH can be corrected by adding a pH Increaser.

ALKALINITY

Total alkalinity is a measure of the alkaline in the water. They act as a pH buffer or a pH stabilizer preventing large changes in the pH. The total alkalinity should be between 80 to 150 ppm; ideally 120 ppm. Tablet chlorine and bromine tend to gradually lower the alkalinity level.

Low total alkalinity causes:

• the pH to wander

• corrosive water

• disinfectants to be ineffective

To raise the total alkalinity, add ALKA RISE.

High total alkalinity causes:

• cloudy water

• scale formation

To lower the total alkalinity, add a pH Reducer.

CALCIUM HARDNESS

Calcium hardness is the hardness present due to dissolved calcium. The desired range is 150 ppm to 280 ppm.

Low calcium hardness causes:

• corrosive water

• staining of spa

To correct this problem, add a Scale Preventative. (Do not fill the spa with soft water!)

44

DOC: OM-A-2017-EN


COMMON SPA WATER PROBLEMS

PROBLEM POSSIBLE CAUSE

CLOUDY WATER

COLOURED WATER

FOAMING a) Organic contaminants build up b) Suspended particles c) pH high d)Total Alkalinity too high e) Hardness too high f) Poor filtration g) High dissolved solids a) Dissolved copper, iron and other metals from source water or equipment b) Algae c) Fragrance a) High concentration of oils and organic contaminants being agitated by jets b) Soft water

SCALE DEPOSITS High calcium level, high pH, high alkalinity

SOLUTION

a) Shock treatment with a Spa Shock b) Add a Brightener, use scum ball c) Add pH reducer, until pH level reads

7.2 - 7.6 d) Add pH reducer, adjust total alkalinity to 80-150ppm e) Add a Scale Preventative, circulate through a water softener until hardness is 150-280ppm. f) Dirty filter, clean with Cartridge

Cleaner g) Empty spa and refill a) Use Scale Preventative, have your dealer check water balance b) Add an Algaecide c) Stop the use of fragrance a) Squirt Defoamer on foam; use the scum ball or spa ball b) Add a Calcium Increaser until hardness is 150-280ppm.

Drain partially, add a Scale Preventative to correct pH level to 7.2 - 7.6 and alkalinity to 80-150ppm.

Shock with a Spa Shock ODOUR High level or organic contaminants, combined bromine pH too low EYE/SKIN IRRITATION

NO BROMINE READING High concentration of organic contaminants using up sanitizers

Add a pH Booster until level is 7.2 - 7.6

Add sanitizers (bromine) until levels are up to recommended range


DOC: OM-A-2017-EN

45

46

DOC: OM-A-2017-EN


SPA OWNER’S MANUAL

IMPORTANT SAFETY INSTRUCTIONS

PART B – BRAND SPECIFIC MANUAL

Pour voir ou imprimer ce document en Français, veuillez visiter:

http://www.sunrisespas.com/site/owners

ELECTRICAL CONNECTION

KEYPAD OPERATION

INS-M-B-17

Read in conjunction with Part A – General Manual to form a complete Owner’s Manual

2

INDEX

Table of Contents

BRAND CONFIGURATION TABLE ................................................................................................................................................................ 3

ELECTRICAL CONNECTION - GENERAL INFORMATION ......................................................................................................................... 4

LOCATING A CONDUIT WITHIN A CONCRETE PAD ............................................................................................................................... 4

SUPPLY CABLE ENTRY INTO SPA EQUIPMENT AREA ............................................................................................................................. 4

HOW TO PASS THE CABLE THROUGH THE SPA ENCLOSURE ................................................................................................................ 4

NORTH AMERICAN 60HZ MODELS ....................................................................................................................................................... 5

115 VOLT SUPPLY CONNECTION ........................................................................................................................................................... 6

CONVERTIBLE/MULTI VOLTAGE SUPPLY OPTION ................................................................................................................................. 6

230 VOLT SUPPLY CONNECTION ......................................................................................................................................................... 10

TYPICAL NORTH AMERICAN GROUND FAULT CIRCUIT INTERRUPTION (GFCI) ................................................................................... 10

SPECIAL NOTE: DISCONNECT SWITCH ................................................................................................................................................ 11

SPECIAL NOTE: EMERGENCY SWITCH ................................................................................................................................................. 11

YOUR FILTER – REMOVAL & REPLACEMENT ....................................................................................................................................... 12

ADDENDUM A – MVP240 CONTROL REFERENCE CARD ..................................................................................................................... 14

ADDENDUM B – TP600 USER GUIDE W/ SIMPLIFIED MENUS ............................................................................................................ 17

ADDENDUM C – TP600 USER GUIDE W/ STANDARD MENUS ............................................................................................................ 32

ADDENDUM D – SPATOUCH (ICON DRIVEN) USER GUIDE ................................................................................................................. 58

DOC: INS-M-B-17 Inspiration

Spas 2017 Owner’s Manual

BRAND CONFIGURATION TABLE

Model

Refreshment

Enjoyment

Relaxation

Exaltation

Euphoria

Sensation

Vitality

Relieve

Revitalize

Rejuvenate

Revive

Recreation

Frame/Bottom

Polysteel/PE

Polysteel/PE

Polysteel/PE

Polysteel/PE

Polysteel/PE

Polysteel/PE

Polysteel/PE

Polysteel/ABS Pan

Polysteel/ABS Pan

Polysteel/ABS Pan

Polysteel/ABS Pan

Polysteel/PE

Filter

Whitewater

Whitewater

Whitewater

Whitewater

Whitewater

Whitewater

Teleweir

Elite

Elite

Elite

Elite

Whitewater

User Guide

(See note below)

MVP 240

MVP 240

TP600 Simplified

TP600 Simplified

TP600 Simplified

TP600 Simplified

TP600 Simplified

TP600 Simplified

Note 1

TP600 Simplified

Note 1

TP600 Simplified

Note 1

TP600 Simplified

Note 1

SpaTouch Menu-Driven

(addendum)

Note: The factory default for spas using the TP600 keypad is Simplified Menus. However, more keypad settings and features are possible on some spas by accessing the Standard menus within the spa pack. A spa pack set up change is required to access these settings and features within the standard menus.

Ask your dealer about the set up change required.

When the spa has a circ pump or Microsilk option the spa pack changes and so does the default setting for the keypad to Standard menus.

Note 1: If spa is equipped with BBA audio system, keypad is upgraded to SpaTouch icon driven version.

Inspiration Spas 2017 Owner’s Manual

DOC: INS-M-B-17

3

4

ELECTRICAL CONNECTION – GENERAL

INFORMATION

A. LOCATING A CONDUIT WITHIN A CONCRETE PAD

If your intent is to bring a conduit and power wires up under the spa we suggest that it enter the spa cavity in the front, left corner; 6” (15cm)

Dimension A in from the left and 6” (15cm) Dimension B up from the front.

See A & B on the diagram below. This location will allow you to stay clear of spa pumps and other equipment while giving you a short and easy access to the left side of the spa pack, where the electrical entry hole and terminal block are located.

B. SUPPLY CABLE ENTRY INTO SPA EQUIPMENT AREA

•

You may enter the spa cavity at any other point around spa provided you have reviewed the location and determined there is no interference. You may also decide to enter at an adjoining wall

(depending on the positioning of the spa) and route a conduit along the spa kicker. Ask your electrician for his/her advice in these matters.

•

In all cases the best side for entry of the supply cable is the side to your left when you are standing at the equipment panel.

•

Right side entry is possible; however, this may involve additional supply cable, parts and time.

HOW TO PASS THE CABLE THROUGH THE SPA ENCLOSURE

POLYSTEEL FRAME WITH POLYETHYLENE BOTTOM AND POLYSTEEL PANELS

a) You can choose to notch the polysteel panel so you can pass the cable/conduit through and still be able to remove/replace the panel for servicing. You should consider securing the cable or conduit to the spa’s metal frame where cable/conduit passes through the cabinet. b) You may also route a cable up under the corner. The curved panel is flexible enough and there is enough space to run the cable this way. Removing the corner may help you to do this easier. c) On a concrete pad where you have a conduit or cable coming up within the perimeter of the spa, you can easily cut an opening in the polyethylene bottom to access the cable or conduit/wires. See above table for recommended opening location.

You may wish to insulate any opening or cut-out you make in the spa’s cabinet panel or corner or bottom to keep cold air and small animals out.



NORTH AMERICAN (60HZ) MODELS

Please note the following important information:

When using this electrical equipment, basic safety instructions should be followed, including the following:

READ AND FOLLOW ALL DIRECTIONS

1) Electrical installation must be carried out by a qualified electrician strictly in accordance with local governing codes.

2) A terminal marked "ground" is located within the control box. To reduce the risk of electric shock this terminal must be connected to the grounding means provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying the equipment.

3) At least two lugs marked "bonding lugs" are provided on the external surface of the control box. To reduce the risk of electric shock connect the local common bonding grid in the area of the hot tub or spa to these terminals with an insulated or bare copper conductor not smaller than No. 6 AWG.

4) All field installed metal components such as rails, ladders, drains or other similar hardware within

3m (10 ft.) of the spa or hot tub shall be bonded to the equipment grounding bus with copper conductors not smaller than No. 6 AWG.

5) Test the ground fault circuit interrupter before each use of the spa.

6) Before servicing any electrical components of the system make sure that the power supply is switched off.


DOC: INS-M-B-17

5

6

115 VOLT CORD CONNECTION (Option – Refreshment, Enjoyment

Standard – Vitality)

This unit has been built, tested and approved with a cord connected 115VAC built in Ground Fault Circuit

Interrupter (GFCI).

The cord must only be plugged into a receptacle that is connected to a dedicated 15A breaker or fuse.

DO NOT extend the connection by the use of an extension cord. This will void the warranty and could cause damage to the spa and its’ users.

GFCI Test Procedure:

1. With the GFCI plugged into a grounded 115VAC, 15A outlet press the yellow TEST button.

2. The spa should shut off and a small light between the TEST and RESET buttons should be lighted.

3. Press the red RESET button to reset the GFCI and start the spa.

FAMILIARIZE yourself with the test procedure for the GF CI. TEST the GFCI upon every use of the spa.

If the GFCI does not shut the spa off when the TEST button is pressed or does not start up when the

RESET button is pressed DO NOT USE THE SPA. Contact your dealer and/or a qualified electrician immediately. Take steps to ensure that no person(s) can use the spa while the problem is being reviewed and corrected.

Note: In new installations, GFCI trippings due to mis-wiring are very common.

If the breaker is properly wired, GFCI trippings can occur when the total amount of current drawn by the spa exceeds the rating of the breaker. Such an occurrence, however, is very unlikely, since each output of the spa pack is individually fused and fuses will blow before the GFCI trips. A current leak to the ground will also make the GFCI trip. If one or more of the components is faulty and there is a leak of more than 5 mA, the GFCI will trip to prevent electrocution.

Cord and Plug Connected – Convertible Units (Vitality Only)

This spa was factory made as a 120 VAC spa with corded GFCI. Its’ power input can be converted to a 120 or 240VAC permanent connection. This must be done by employing a qualified electrician and in accordance with local electrical codes.

CAUTION:

Connect only to a circuit protected by a Class A Ground Fault Circuit Interrupter when converting to the permanent connection mode.

To convert from the factory 120VAC cord connected GFCI to 120 or 240VAC permanent connection follow these instructions:



1. Remove the 120VAC cord with GFCI at the terminal block and ground bar. ( 3 connection points)

2. A) to connect a 120VAC permanent supply from a class A GFCI:

Connect White (Neutral/N), Black (Hot/L1) and Green (ground wire/GRN) to the input terminal block as shown on the wiring diagram inside the spa pack cover. See the spa ratings label for current, wire size and breaker requirements.

B) to connect to a 240VAC permanent supply from a class A GFCI:

Connect White (Neutral/N), Black (Hot/L1), Red (Hot/L2) and Green (ground wire/GRN) to the input terminal block as shown on the wiring diagram inside the spa pack cover. See the spa ratings label for current, wire size and breaker requirements.

Steps 3, 4 & 5 apply only to a 240VAC permanent connection.

3. Remove the white jumper wire connecting J42 on the WHT AC bank (area 1) to J38 on the RED AC bank (area 3). See diagram below.

4. Before powering up the spa, locate the dipswitch bank in the top, right corner of the circuit board.

5. Locate dipswitch #2 and move it to the ON position (UP).

Jumper (step 3)

Dip Switches

(steps 4 & 5)


DOC: INS-M-B-17

7

8

Cord and Plug Connected – Convertible Units

(Refreshment, Enjoyment)

This spa was factory made as a 120 VAC spa. Its’ power input can be converted to a 240VAC permanent connection. This must be done by employing a qualified electrician and in accordance with local electrical codes.

Note: This 240V conversion allows the heater to operate as 4Kw @ 240V. The jet pump, ozone and AV outputs remain 120V.

CAUTION:

Connect only to a circuit protected by a Class A Ground Fault Circuit Interrupter when converting to the permanent connection mode.

To convert from the factory 120VAC to 240VAC permanent connection follow these instructions:

1. Remove the 120VAC cord with GFCI (if applicable) at the terminal block and ground bar. ( 3 connection points)

To connect to a 240VAC permanent supply from a class A GFCI:

Connect White (Neutral/N), Black (Hot/L1), Red (Hot/L2) and Green (ground wire/GRN) to the input terminal block as shown on the wiring diagram inside the spa pack cover. See the spa ratings label for current, wire size and breaker requirements.

2. Remove the white jumper wire connecting J11 on the WHT AC bank (area 1) to J32 on the RED AC bank (area 3). See diagram below.

3. Before powering up the spa, locate the dipswitch bank in the lower, right corner of the circuit board.

4. Locate dipswitch #10 and move it to the OFF position (DOWN).

5. Reset Persistent memory



Any time you change a DIP Switch, other than A1, you must reset Persistent Memory for your new DIP

Switch Settings changes to take effect. If you do not reset Persistent Memory, your system may function improperly.

STEP 2

To Reset Persistent Memory:

A. Power down by disconnecting power source from spa

B. Put a jumper across J43, covering both pins

(See illustration)

C. Power up by connecting power source to spa

D. Wait until “Pr” is displayed on your panel

E. Power down again

F. Remove jumper from J43

(May also move to cover 1 pin only)

G. Power up again

STEP 3-4

STEP 5

To Reset Persistent Memory:

•

Power down by disconnecting power source from spa

•

Put a jumper across J43, covering both pins

(See illustration)

•

Power up by connecting power source to spa

•

Wait until “Pr” is displayed on your panel

• Power down again

•

Remove jumper from J43

(May also move to cover 1 pin only)

• Power up again


DOC: INS-M-B-17

9

230 VOLT SUPPLY CONNECTION

VS SERIES SPA PACK BP SERIES SPA PACK

Power Requirements

240VAC, 60Hz, Class A GFCI-protected service

4 wires (Hot-Line 1, Hot-Line 2, Neutral, Ground)

For current requirements & breaker rating see nameplate on spa.

Power Up Screen

Each time the system powers up, a series of numbers is displayed. After the start-up sequence of numbers, the system will enter Priming Mode. Next, refer to the User Guide for your keypad at the back of this manual.

TYPICAL NORTH AMERICAN GFCI

Several different models of GFCIs are available on the market.

Note that our illustrations are generic.

10



WIRE SIZE AND OVER CURRENT PROTECTION (CANADA/US)

Amp rating of spa Supply Wire type and size

More than To 60C copper, AWG 75C copper, AWG

Over Current

Protection (amps)

16

20

24

28

20

24

28

32

10

10

8

8

10

10

10

8

25

30

35

40

32

36

36

40

6

6

8

8

45

50

40 48 4 6 60

Note: If your GFCI trips immediately on start-up or during the opening use of the spa, DO NOT USE THE

SPA and take precautions to ensure that no one uses the spa, while you contact your dealer/electrician.

GFCI trips on newly installed spas are predominantly caused by mis-wired GFCIs.

SPECIAL NOTE: DISCONNECT SWITCH

This unit must be connected to a disconnect that de-energizes power to the entire unit for servicing, maintenance or the like. The disconnect switch, with marked "OFF" position, must be located within sight from the equipment and at least 5ft. (1.52m) from the inside walls of the spa.

SPECIAL NOTE: EMERGENCY SWITCH

This unit is intended for use in a single family dwelling. When used in locations other than a single family dwelling, a clearly labelled emergency switch, readily accessible to the occupants and at least 5ft. (1.52m) away from the unit, shall be provided as part of the installation.


DOC: INS-M-B-17

11

12

YOUR FILTER – REMOVAL & REPLACEMENT

Our various spa models use different filter systems depending on the spa design. Identify which filter system is in your spa and check (√) it off for future reference.

“TELEWEIR” SKIM FILTER

Single cartridge mounted vertically 50 sq ft, 14 ½” (36.8cm) high (part #PWW50L)

Also available: Dual Core Cartridge (part #PDC570-AFS)

1. Shut off your spa at the Ground Fault Circuit

Interrupter (GFCI) or Residual Current

Detector (RCD).

2. Lift the floating weir and filter sleeve straight up above the filter body to remove.

3. Use the cartridge handle to thread the cartridge out of the filter body.

4. Examine, clean, rotate or replace the cartridge as necessary.

5. Hold the filter sleeve and twist weir top to remove weir and allow basket debris to be dumped out.

6. Reverse the procedure to install new or cleaned cartridges.

ELITE TELESCOPING WEIR FILTER

Single cartridge, vertically mounted, 75 sq. ft. 14 13/16”(37.6cm) high (part #PLBS75)

1. Shut off your spa at the Ground Fault Circuit

Interrupter(GFCI) or Residual Current

Detector(RCD)

2. Use the raised tabs on the outer ring to turn the ring and 2 piece weir assembly counter clockwise until it releases form the filter body. Remove and set aside.

3. Remove the debris basket by grasping the inner tab. Dump any debris and set aside.

4. Pull cartridge straight up and out of the filter body.

5. Examine, clean, rotate or replace the cartridge as necessary.

6. Reverse the procedure to install new or cleaned cartridge.



WHITEWATER SKIM FILTER

Dual cartridges mounted vertically 50 sq ft each, 8” (20cm) high (part #PPG-50P4)

1) Shut off your spa at the Ground Fault Circuit


Detector (RCD).

2) Remove the decorative top cover.

3) Remove each cartridge by simply grasping the handle and turning it until it threads out of the cartridge mount.

4) Reverse the procedure to install new or cleaned cartridges.

WHITEWATER SKIM FILTER – SPLIT VERSION

Dual cartridges mounted vertically – 1 at 50 sq. ft., 8” (20cm) high (part #PPG-50P4)

– 1 at 35 sq. ft., coreless, 7¼” (18.4cm) high (part #PSN35)

1) Shut off your spa at the Ground Fault Circuit


Detector (RCD).

2) Remove the decorative top cover

3) Remove the 50 sq. ft. cartridge by using its’ top handle to thread the cartridge off its’ mount.

4) Remove the 35 sq. ft. coreless cartridge by threading the large nut off the permanent core. Then lift the cartridge up to remove it.

5) Reverse the procedure to install new or cleaned cartridges.


DOC: INS-M-B-17

13

14

ADDENDUM A

MVP 240

Control Reference Card




DOC: INS-M-B-17

15

16



ADDENDUM B

TP600 User Guide

With Simplified Menu Feature


DOC: INS-M-B-17

17

18




DOC: INS-M-B-17

19

20




DOC: INS-M-B-17

21

22




DOC: INS-M-B-17

23

24




DOC: INS-M-B-17

25

26




DOC: INS-M-B-17

27

28




DOC: INS-M-B-17

29

30




DOC: INS-M-B-17

31

32

ADDENDUM C

TP600 User Guide

With Standard Menu Feature

•

Applies to all spas with a dedicated circulation pump and/or MicroSilk option.

•

Applies to any spa where the set up number has been re-configured to allow standard menu features.




DOC: INS-M-B-17

33

34




DOC: INS-M-B-17

35

36




DOC: INS-M-B-17

37

38




DOC: INS-M-B-17

39

40




DOC: INS-M-B-17

41

42




DOC: INS-M-B-17

43

44




DOC: INS-M-B-17

45

46




DOC: INS-M-B-17

47

48




DOC: INS-M-B-17

49

50




DOC: INS-M-B-17

51

52




DOC: INS-M-B-17

53

54




DOC: INS-M-B-17

55

56




DOC: INS-M-B-17

57

ADDENDUM D

NEW

SpaTouch Icon Driven User Guide

58




DOC: INS-M-B-17

59

60




DOC: INS-M-B-17

61

62




DOC: INS-M-B-17

63

64




DOC: INS-M-B-17

65

66




DOC: INS-M-B-17

67

68




DOC: INS-M-B-17

69

70




DOC: INS-M-B-17

71

72




DOC: INS-M-B-17

73

74




DOC: INS-M-B-17

75

76




DOC: INS-M-B-17

77

78




DOC: INS-M-B-17

79

80




DOC: INS-M-B-17

81

82




DOC: INS-M-B-17

83

84




DOC: INS-M-B-17

85

86




DOC: INS-M-B-17

87

88




DOC: INS-M-B-17

89

90



NOTES


DOC: INS-M-B-17

91

92



No results