Scanspeak Full V10.vp

Model Imp

Ω

Fs Hz Qts Vas

Ltrs

Power

Il lu mi na tor Se ries Tweeters

D2004/6020-00: ¾" dome tweeter, 55.5mm Ø, metal grill, chamber 4 600 60

D3004/6020-00: 1" dome tweeter, 62mm Ø, metal grill, chamber 4 700 50

dB

2.83V/m

88.4

89.2

Xmax mm P

0.2

0.2

Box Li ter

S

ealed/

V

ented

F3 Hz Price

Each

$121.85

$124.55

D3004/6020-10: 1" dome tweeter, 62nn Ø, metal grill, deep cham ber 4 425

R2004/6020-00: ¾" ring ra di a tor, 55.5mm Ø, metal grill, chamber 4 600

R3004/6020-00: 1" ring ra di a tor, 62mm Ø, metal grill, cham ber 4 625

R3004/6020-10: 1" ring ra di a tor, 62mm Ø, metal grill, deep cham ber 4 420

D3004/6640-00: 1" Be ryl lium dome, AirCirc neo. mag net, Black

D3004/6600-00: 1" dome, AirCirc, neo dym ium mag net

4

4

490

500

D3004/6620-00: 1" dome, AirCirc, neo mag net, rub ber front, Black

D3004/6620-01: 1" dome, AirCirc, neo mag net, rub ber front, Silver

4

4

500

500

50

60

50

50

89.6

86.9

87.4

87.4

[email protected]

90.7

[email protected]

91.6

[email protected]

91.6

[email protected]

91.6

R3004/6620-00: 1" ring ra di a tor, AirCirc, neo, rub ber front, Black 4 520 [email protected]

90.4

R3004/6620-01: 1" ring ra di a tor, AirCirc, neo, rub ber front, Silver 4 520 [email protected]

90.4

Il lu mi na tor Se ries Midranges

12MU/4731T: 4" midrange, pa per cone, neo mag net, under hung VC 4 64 0.24

5.4

80

12MU/8731T: 4" midrange, pa per cone, neo mag net, under hung VC 8 66 0.29

5.9

80

90

87.2

Il lu mi na tor Se ries Woofers

15WU/4741T: 5.25" woofer, pa per cone, neo mag net, under hung VC 4 34 0.23

20.1

80

15WU/8741T: 5.25" woofer, pa per cone, neo magnet, under hung VC 8 35 0.26

20.1

80

85.9

83.4

0.2

0.2

0.2

0.2

0.2

0.2

0.2

0.2

0.2

0.2

3.5

3.5

0.1 / 0.1

0.1 / 0.1

$130.90

$152.40

$157.30

$164.65

$508.20

$212.95

$232.65

$232.65

$271.35

$271.35

190 / 115 $298.70

190 / 115 $298.70

18WU/4741T: 6.5" woofer, pa per cone, neo mag net, under hung VC

18WU/8741T: 6.5" woofer, pa per cone, neo mag net, under hung VC

R2904/7000-09: Pre mium Ring Ra di a tor - Black

4

8

30 0.29

49.9

31 0.33

49

80

80

87.2

85.4

18WU/4747T: 6.5" woofer, alu mi num cone, neo mag net, underhung 4

R2904/7000-05: Pre mium Ring Ra di a tor - Black w/sil ver plug

32 0.28

48.7

18WU/8747T: 6.5" woofer, alu mi num cone, neo mag net, under hung 8 33 0.31

49.2

Rev e la tor Se ries Tweeters

R2904/7000-00: Pre mium Ring Ra di a tor - Sil ver 4 520

80 85.5

[email protected]

94.5

4 520

80 88.1

[email protected]

94.5

4 520 [email protected]

94.5

D2904/7100-02: Pre mium Wide Sur round Tweeter - Sil ver

D2904/7100-03: Pre mium Wide Sur round Tweeter - Black

4 520

4 520

[email protected]

94.5

[email protected]

94.5

9

9

9

9

9

9

0.2

0.2

0.2

0.15 / 0.25

115 / 60 $342.15

0.15 / 0.25

105 / 58 $342.15

0.25 / 0.5

80 / 55 $341.40

0.35 / 0.6

70 / 50 $341.40

0.2 / 0.45

97 / 59 $325.50

0.25 / 0.6

84 / 55 $325.50

$371.15

$371.15

$371.15

0.2

0.2

D2905/9900: 1” tex tile dome, SD-2, LCD, NRC, CDD

12M/4631G: 4.5” slit pa per cone, neo dym ium mag net, R3


Rev e la tor Se ries Midranges

4 75 0.33

2.4

40@75

15M/4531K: 5" slit pa per cone midrange, Glass former 4 35 0.22

24

Rev e la tor Se ries Mid/Bass & Woofers

15W/4531G: 5” slit pa per cone, NRCS, SD-1, R3, Glass former 4 39.5

0.32

16 60

91

89

90

0.4

3.0

3.0

0.7 / 1.0

3.0 / 5.0

$262.30

160 / 100 $314.20

100 / 70 $223.80

87 6.5

4 / 6 88 / 58 $235.70

15W/8530K-00: 5” pa per cone, NRCS, SD-1, R3, Glass former 8 30 0.27

28 60 85.5

6.5

5.1 / 7.4

77 / 55 $213.90

15W/8530K-01: 5” pa per cone, NRCS, SD-1, R3, Glass for mer 8 30 0.35

28 60 84.5

6.5

9.5 / 15 60 / 40 $223.70

18W/4531G: 7" slit pa per cone, SD-1, R3, Glass for mer 4 33 0.35

42 70 90 6.5

14 / 23 65 / 41 $237.05

18W/8531G: 7” slit pa per cone, SD-1, R3, Glass former 8 28 0.36

59 60 87 6.5

21 / 36 54 / 35 $237.05

22W/4851T: 8" hard pa per cone, SD-1, Ti ta nium for mer 4 20.5

0.22

127 170 89 9.0

10 / 28 70 / 40 $374.40

22W/8851T: 8" hard pa per cone, SD-1, Titanium for mer 8 21 0.25

127 170 88 9.0

18 / 34 60 / 38 $374.40

22W/8857T: 8" Black Alu mi num cone, SD-1, Ti ta nium former 8 23 0.30

89 170 89 9.0

14 / 35 60 / 38 $348.95

26W/8861T: 10" hard pa per cone, SD-1, Ti ta nium for mer 8 19 0.31

234 170 88.5

9.0

55 / 90 40 / 28 $416.70

26W/4867T: 10" Black Alu mi num cone, SD-1, Ti ta nium for mer 4 18 0.30

223 170 89 9.0

46 / 71 43 / 29 $381.30

26W/8867T: 10" Black Alu mi num cone, SD-1, Ti ta nium for mer 8 19 0.29

179

23W/4557T-02: 10" Alu mi num Cone, SD-1, Ti ta nium for mer, Black 4 20.5

0.44 43.5

170

23W/4557T-00: 10" Alu mi num Cone, SD-1, Ti ta nium for mer, Silver 4 20.5

0.44 43.5

23W/0-00-00: 10" Alu mi num Cone Pas sive Ra di a tor, Silver Fs 10.5 Hz, Sd 232 cm 2

225 83 13 28 / 59 33 / 27

, Mms 400g, Vas 43.5 Ltrs, Qms 11.5, Ex cur sion +20mm

$434.20

$166.90

225

87

83

9.0

13

36 / 57

28 / 59

46 / 31 $381.30

33 / 27 $434.20

23W/0-00-02: 10" Alu mi num Cone Pas sive Ra di a tor, Black

D2008/8512: ¾" dome, chamber

Fs 10.5 Hz, Sd 232 cm

2

, Mms 400g, Vas 43.5 Ltrs, Qms 11.5, Ex cur sion +20mm

Clas sic Se ries Tweet ers

8 800 150#4k 90 0.7

$166.90

$77.45

D2010/8513: ¾” dome, cham ber, foam on face plate, ff 8 800 150@4k 90 0.7

$83.85

D2905/9300: 1” tex tile dome, cham ber, FF 8 650 [email protected]

90 0.4

$122.55

D2905/9500: 1” tex tile dome, NRC, FF

D2905/9700: 1” tex tile dome, SD-2, LCD, NRC

D2904/9800: 1” alu mi num dome, dif fuser, SD-2, NRC

8 550

8 500

4 500

[email protected]

90

[email protected]

89.5

[email protected]

90

0.4

0.4

0.1

$312.30

$312.30

$140.15

$180.25

$214.00

Model

D3806/8200: 1.5" tex tile dome mid/tweeter

18W/8535: 7” car bon pa per cone, SD-1, R3

18W/8542: 7" pa per cone, SD mo tor, foam surround

18W/8545: 7” car bon pa per cone, SD-1, R3

18W/8545K: 7” car bon pa per cone, SD-1, R3, Glass former

Imp

Ω

Fs Hz Qts Vas

Ltrs

Power

Clas sic Se ries Mid/Tweeter


Clas sic Se ries Woofers

8 26 0.38

72 70

8

8

8

30 0.22

49

28 0.27

48

28 0.28

48

70

100

100

dB

2.83V/m

89

86.5

89

88

87.5

Xmax mm P

0.4

5.0

6.5

6.5

6.5

Box Li ter

S

ealed/

V

ented

30 / 46

4 / 14

8 / 15

9 / 19

F3 Hz Price

Each

$192.00

48 / 33 $182.95

107 / 58 $194.40

75 / 46 $174.40

70 / 42 $170.15

21W/8555:8" pa per/carbon cone woofer, SD-1 8 20 0.31

134 100 87

26W/8565: 10" pa per/car bon cone woofer, SD-1 8 20 0.41

225 100

Dis cov ery Se ries Dome Tweet ers

D2606/9200: 1" tex tile dome tweeter 6 1100

D2606/9220: 1" tex tile dome tweeter with cham ber, vented pole piece 6 650

[email protected]

91.4

100@2k

88

91

5.5

6.5

0.5

0.5

20 / 35

60 / -

55 / 36 $247.75

40 / $259.20

$36.65

$51.90

D2604/8330: 1" tex tile dome, large roll surround 4 475 100@2k 94.1

0.3

$53.90

D2608/9130: 1" tex tile dome, dou ble mag net, high efficiency 8 700 100@2k 91.3

0.5

$81.40

R2604/8320: 1" tex tile ring tweeter, wave guide, chamber

10F/4424G: 4" fi ber glass cone midrange, neo dym ium magnet

4 550

R2604/8330: 1" tex tile ring dome tweeter, wave guide, dou ble magnet 4 630 100@2k

Dis cov ery Se ries Midranges

D7608/9200-10: 3" tex tile dome midrange, needs cham ber on back 8 300 80@500

4

100@2k

90 0.30 2.06

15RMS

90.8

91.9

92

0.2

0.2

0.5

1 / -

$54.45

$63.80

500 / $103.10

89.8

2.6

1.5 / 270 / $100.95

10F/8424G: 4" fi ber glass cone midrange, neo dym ium mag net 8 90 0.37

2.1

15RMS 86.6

2.6

1.5 / 210 / $100.95

15M/4624G: 5" fi ber glass cone midrange, phase plug, 24mm VC

12W/4524G: 5" fi ber glass cone woofer, 24mm VC

4 100 0.43

3.6

75RMS

Dis cov ery Se ries Woofers

4 50 0.27

8.2

40RMS

92.4

88.8

1.5

1.5

2.5 / -

2 / 3

205 / $77.85

145 / 80 $64.90

12W/8524G: 5" fi ber glass cone woofer, 24mm VC 8 52 0.32

8.2

40 RMS 85.8

1.5

2 / 4.5

135 / 75 $64.90

15W/4434G: 5" fi ber glass cone woofer, short ing ring, 34mm VC 4 43 0.21 12.9

60RMS 89.7

4.3

3 / 3.5

160 / 80 $70.70


60RMS 86.9

4.2

3 / 5 145 / 75 $70.70


60RMS 90.8

4.3

5 / 12 100 / 60 $73.75


60RMS 88 4.2

6 / 15 90 / 55 $73.75

22W/4534G: 8" fi ber glass cone woofer, short ing ring, 34mm VC 4 30 0.34

95 70RMS 92.4

5.7

18 / 45 75 / 40 $88.20

22W/8534G: 8" fi ber glass cone woofer, short ing ring, 34mm VC

30W/4558T: 12" Alu mi num cone subwoofer, short ing ring

8

26W/4534G: 10" fi ber glass cone woofer, short ing ring 34mm VC

26W/8534G: 10" fi ber glass cone woofer, short ing ring 34mm VC 8 23 0.40

150 70RMS 89

Dis cov ery Se ries Subwoofers and Pas sive Radiators

26W/4558T: 10" Alu mi num cone subwoofer, short ing ring 4 20 0.28

104 150RMS 89

26W/0-00: 10" Alu mi num cone pas sive ra di a tor 400 gram

4 23 0.36

156 70RMS 90.5

6

6

12.5

35 / 85

45 / 100

- / 56

55 / 32 $106.40

50 / 31 $106.40

- / 28 $247.40

Use with 26W/4558T in 1 cu bic foot for F3 of 35Hz use amp with 25Hz boost $132.75

4

30 0.39 94.2

70RMS

21 0.34

147 150RMS

88.8

89

5.8

12.5

18 / 45

- / 90

75 / 40 $88.20

- / 26 $270.30

30W/0-00: 12" Alu mi num cone pas sive ra di a tor 425 gram Use with 30W/4558T in 2 cu bic feet for F3 of 30Hz

Dis cov ery Se ries Autosound Com po nent Systems

820012: 5" 2-way Com po nent Sys tem, 2x 5" fi ber glass cone woof ers, 2x 19mm ring dome tweet ers with flush/wedge mounts, 2x 2500Hz cross overs

$158.15

$432.00

820013: 6" 2-way Com po nent Sys tem, 2x 6" fi ber glass cone woof ers, 2x 19mm ring dome tweet ers with flush/wedge mounts, 2x 3000Hz cross overs

290001: Scan speak flow re sis tive aperiodic vent, used to lower the box Q of a sealed box. It makes the driver be have as if the box is 25% larger. Each

$450.00

$14.70

127001: Scan speaker grill for Clas sic 18W woof ers, does not fit the Rev e la tor or Il lu mi na tor woof ers. Each

Clas sic Vifa Driv ers Built by Scan-Speak

P13WH00-08: 5" min eral filled poly cone, 140mm cast frame 8 60 0.33

10 40

P17WJ00-08: 6.5" min eral filled poly cone, 170mm cast frame 8 37 0.35 34.7

40

P21WO20-08: 8" min eral filled poly cone, 215mm cast frame 8 28 0.33

113 80

88

88

91

4

4

4

3 / 6

8 / 15

20 / 45

$15.00

145 / 80 $76.20

90 / 55 $76.90

70 / 40 $85.55

Founded in 1970, Scan-Speak still resides at our original address in Videbaek, Denmark. Located in the heart of the Jutland peninsula, our acoustic engineers adhere to our legendary policy of "Never compromise". We never compromise on our product quality, sound quality or pursuit of perfection in a given application. We set the loudspeaker industry's gold standard for audiophiles, and are constantly viewed as a market benchmark by other high-end speaker manufacturers.

For close to 40 years, Scan-Speak has been on a quest to create transducers that reveal the finest details in recordings, concealing nothing from the listener. This quest has resulted in several revolutionary inventions, where distortion in the magnet systems and the moving parts of the speaker is minimized. Our philosophy is simple: the emitted sound must be dynamic, giving a transient response and providing tonal balance.

Illuminator D2004/6020-00 4Ω

The face plates are die cast in aluminum for a beautiful look with maximum mechanical stability.

D2004/602000 is optimized to offer small package sizes that can fit into tight spaces such as compact cabinets and automotive trim pieces.

The back chamber is die cast in aluminum and designed with a contoured shape that functions as a heat sink in high power applications.

Driver Highlights: 3/4” soft dome, compact size, ring neodymium magnet, aluminum faceplate and house, protective grill.


The face plates are die cast in aluminum for a beautiful look with maximum mechanical stability.

D3004/602000 is optimized to offer small package sizes that can fit into tight spaces such as compact cabinets and automotive trim pieces.


This tweeter is a good choice for home or autosound systems.

Driver Highlights: 1” soft dome, compact size, ring neodymium magnet, aluminum faceplate and house, protective grill.

TECHNICAL DATA:

Sensitivity 2.83V/1M 88.4dB

Free air resonance Fs 600 Hz

DC resistance 3.4 ohm

V.C. inductance 0.02 mH

Power 12dB@Hz 50W

Effective cone area 4.5 cm 2

V.C. diameter 19 mm

V.C. height 1.8 mm

Air gap height 2.5 mm

Lin. & max. excursion ±0.4 / ±01.8mm

Force factor BL Product 1.3 Tm

Moving mass incl. air 0.22 g

Outside diameter 55.5 mm

Cutout diameter 42.1 mm

Flange thickness 5 mm

Depth 29.3 mm

Screw Circle 47.6 mm

TECHNICAL DATA:





Power 12dB@Hz 50W

Effective cone area 7 cm 2

V.C. diameter 26 mm

V.C. height 2.1 mm


Lin. & max. excursion ±0.2 / ±1.6 mm






Depth 21.5 mm



The face plates are die cast in aluminum for a beautiful look with maximum mechanical stability. D3004/602010 is optimized to offer small package sizes that can fit into tight spaces such as compact cabinets and automotive trim pieces.


Driver Highlights: 1” soft dome, compact size, ring neodymium magnet, aluminum faceplate and house, protective grill, large chamber.

TECHNICAL DATA:





Power 12dB@Hz 50W


V.C. diameter 26 mm

V.C. height 2.1 mm








Depth 55.4 mm


Illuminator R2004/6020-00 4Ω

The face plates are die cast in aluminum for a beautiful look with maximum mechanical stability. R2004/602000 is optimized to offer small package sizes that can fit into tight spaces such as compact cabinets and automotive trim pieces.


Driver Highlights: ¾” soft ring dome, compact size, ring neodymium magnet, aluminum faceplate and house, protective grill, chamber.

TECHNICAL DATA:

Sensitivity 2.83V/1M 86dB




Power 12dB@Hz 50W


V.C. diameter 19 mm

V.C. height 1.8 mm








Depth 29.3 mm



The face plates are die cast in aluminum for a beautiful look with maximum mechanical stability. R3004/602000 is optimized to offer small package sizes that can fit into tight spaces such as compact cabinets and automotive trim pieces.

The back chamber is die cast in aluminium and designed with a contoured shape that functions as a heat sink in high power applications.

Driver Highlights: 1” soft ring dome, compact size, ring neodymium magnet, aluminium faceplate and house, protective grill, chamber.

TECHNICAL DATA:





Power 12dB@Hz 50W


V.C. diameter 26 mm

V.C. height 2.1 mm








Depth 21.5 mm



The face plates are die cast in aluminum for a beautiful look with maximum mechanical stability. D3004/602010 is optimized to offer small package sizes that can fit into tight spaces such as compact cabinets and automotive trim pieces.

The back chamber is die cast in aluminium and designed with a contoured shape that functions as a heat sink in high power applications.

Driver Highlights: 1” soft ring dome, compact size, ring neodymium magnet, aluminium faceplate and house, protective grill, large chamber.

TECHNICAL DATA:





Power 12dB@Hz 50W


V.C. diameter 26 mm

V.C. height 2.1 mm








Depth 55.4 mm



This tweeter features a 99% pure

Beryllium dome diaphragm. The large roll surround and Beryllium dome diaphragm provide a flat frequency response to above 40KHz with outstanding off-axis dispersion and a silky-smooth sound.

AirCir magnet system with neodymium magnets and unique air flow.

Driver Highlights:- 1" Beryllium Diaphragm (99% pure Beryllium)-

AirCirc Magnet System with 6 Neodymium Magnet slugs- Die cast rubber painted aluminium faceplate for maximum mechanical stability and beautiful look- Protective grill.


The new D3004/660000 builds on the experience of the one-inch R29 ring radiator, resulting in low resonance frequency, but further provides the extended dispersion characteristics of a ¾-inch dome.

Tymphany’s unique AirCirc Magnet

System — named for the way it optimizes air flow within the chamber rearranges the traditional magnet structure from a single magnet to an open magnetic circuit comprised of six separate neodymium slugs. This, in combination with the chamber, results in the elimination of the reflections and resonances that compromise the performance of traditional motors.

TECHNICAL DATA:





Power 12dB@Hz [email protected]


V.C. diameter 26 mm

V.C. height 2.1 mm





Outside diameter 104 mm

Cutout diameter 77 mm


Depth 23 mm

Screw Circle 90 mm

TECHNICAL DATA:







V.C. diameter 26 mm

V.C. height 2.1 mm








Depth 23 mm

Screw Circle 90 mm


Tymphany’s unique AirCirc

Magnet System - named for the way it optimizes air flow within the chamber – rearranges the traditional magnet structure from a single magnet to an open magnetic circuit comprised of six separate neodymium slugs. This, in combination with the chamber, results in the elimination of the reflections and resonances that compromise the performance of traditional motors. The D3004 gives engineers improved control over critical midrange performance, for superb vocal rendition and excellent imaging at all listening locations. Driver Highlights: 1" soft dome,

AirCirc Magnet System, Rubber painted aluminum faceplate, Black

TECHNICAL DATA:







V.C. diameter 26 mm

V.C. height 2.1 mm








Depth 23 mm

Screw Circle 90 mm



Magnet System - named for the way it optimizes air flow within the chamber – rearranges the traditional magnet structure from a single magnet to an open magnetic circuit comprised of six separate neodymium slugs. This, in combination with the chamber, results in the elimination of the reflections and resonances that compromise the performance of traditional motors. The D3004 gives engineers improved control over critical midrange performance, for superb vocal rendition and excellent imaging at all listening locations. Driver Highlights: 1" soft dome,

AirCirc Magnet System, Rubber painted aluminum faceplate, Silver

TECHNICAL DATA:







V.C. diameter 26 mm

V.C. height 2.1 mm








Depth 23 mm

Screw Circle 90 mm


The ring radiator tweeter uses a phase plug. The dome is attached to the phase plug, so the radiating area is now concentrated around the voice coil. This offers more control and reduces distortion and loss that occur at the center of the dome on dome tweeters.


Magnet System - named for the way it optimizes air flow within the chamber – rearranges the traditional magnet structure from a single magnet to an open magnetic circuit comprised of six separate neodymium slugs.

This, in combination with the chamber, results in the elimination of the reflections and resonances that compromise the performance. Black

TECHNICAL DATA:







V.C. diameter 26 mm

V.C. height 2.1 mm








Depth 23 mm

Screw Circle 90 mm


The ring radiator tweeter uses a phase plug. The dome is attached to the phase plug, so the radiating area is now concentrated around the voice coil. This offers more control and reduces distortion and loss that occur at the center of the dome on dome tweeters.


Magnet System - named for the way it optimizes air flow within the chamber – rearranges the traditional magnet structure from a single magnet to an open magnetic circuit comprised of six separate neodymium slugs.

This, in combination with the chamber, results in the elimination of the reflections and resonances that compromise the performance. Silver

TECHNICAL DATA:







V.C. diameter 26 mm

V.C. height 2.1 mm








Depth 23 mm

Screw Circle 90 mm

Illuminator 4.5" 12MU/4731T-00 4Ω

The Illuminator midrange is based on compact underhung motor systems with large neodymium ring magnets. The patent pending motor offers a very long linear excursion together with a very high force factor. The top plate is shaped to “guide” the backside airflow around the motor and with the very open cast aluminum chassis design the driver is virtually free from compression. The cone and dust cap is made in one piece full cone technology.

Frame diameter 120mm, cutout hole size 101mm, depth 66mm.

TECHNICAL DATA:

Sensitivity 2.83V/1M 90 dB




Power 12dB@Hz 80W


V.C. diameter 32 mm

V.C. height 6.0 mm


Lin. & max. excursion ±3.5 & ±10mm



Net weight 0.8 kg

Vas 5.4 ltrs

Qms 3.64

Qes 0.26

Qts 0.24

Illuminator 4.5" 12MU/8731T-00 8Ω

The Illuminator midrange is based on compact underhung motor systems with large neodymium ring magnets. The patent pending motor offers a very long linear excursion together with a very high force factor. The top plate is shaped to “guide” the backside airflow around the motor and with the very open cast aluminum chassis design the driver is virtually free from compression. The cone and dust cap is made in one piece full cone technology.

Frame diameter 120mm, cutout hole size 101mm, depth 66mm.

TECHNICAL DATA:

Sensitivity 2.83V/1M 87.2 dB




Power 12dB@Hz 80W

Effective cone area 58 cm

V.C. diameter 32 mm

2

V.C. height 6.2 mm





Net weight 0.8 kg

Vas 5.9 ltrs

Qms 3.63

Qes 0.31

Qts 0.29

Illuminator 5.25" 15WU/4741T-00 4Ω

The Illuminator woofers are based on compact under-hung motor systems with large neodymium ring magnets.

The patent pending motor offers a very long linear excursion together with a very high force factor. The top plate is shaped to “guide” the backside airflow around the motor and with the very open cast aluminum chassis design the driver is virtually free from compression.

F3 of 60Hz in 0.25 cubic foot vented .

Frame diameter 149mm, cutout hole diameter 123mm, depth 91mm.

TECHNICAL DATA:





Power 80W


V.C. diameter 42 mm

VC height 8 mm

Air gap 20 mm

Lin. & max. excursion ±9 / ±12 mm

Force factor BL Product 6 Tm

Moving mass incl. air 13 g

Net weight 1.6 kg

Vas 20.1 ltrs

Qms 3.47

Qes 0.25

Qts 0.23






TECHNICAL DATA:





Power 80W


V.C. diameter 42 mm

VC height 8 mm

Air gap 20 mm




Net weight 1.6 kg

Vas 20.1 ltrs

Qms 3.37

Qes 0.28

Qts 0.26






TECHNICAL DATA:





Power 80W


V.C. diameter 42 mm

2

VC height 8 mm

Air gap 20 mm




Net weight 1.7 kg

Vas 49.4 ltrs

Qms 3.56

Qes 0.32

Qts 0.29






TECHNICAL DATA:





Power 80W


V.C. diameter 42 mm

VC height 8 mm

Air gap 20 mm




Net weight 1.7 kg

Vas 48.6 ltrs

Qms 3.51

Qes 0.37

Qts 0.33




Black anodized aluminum cone.


TECHNICAL DATA:





Power 80W


V.C. diameter 42 mm

2

VC height 8 mm

Air gap 20 mm




Net weight 1.7 kg

Vas 48.7 ltrs

Qms 3.42

Qes 0.30

Qts 0.28




Black anodized aluminum cone.


TECHNICAL DATA:





Power 80W


2

V.C. diameter 42 mm

VC height 8 mm

Air gap 20 mm




Net weight 1.7 kg

Vas 49.2 ltrs

Qms 3.31

Qes 0.35

Qts 0.31

R2904/7000 4Ω

The R2904/7000 tweeter is the new flagship tweeter in the Scan-speak line.

This tweeter incorporates many innovative design concepts.

The first notable difference is the use of a phase plug. The dome is attached to the phase plug, so the radiating area is now concentrated around the voice coil.

This offers more control and reduces distortion and loss that occur at the center of the dome on dome tweeters.

The phase plug also acts as a wave guide, reducing high frequency cancellations. A specially designed venting system uses a needle to cut down on turbulence in the air cavity. Better dynamics are achieved by not using ferrofluid, voice coil cooling is performed by the venting system and conduction through copper rings.

The new SD-2 neodymium magnet system improves transient response.

TECHNICAL DATA:







V.C. diameter 28 mm




Net weight 0.42 kg

D2904/7100 4Ω

The D2904/7100 tweeter is a 1" soft dome with wide surround, using the same chambering as the Ring Radiator.

The carefully designed dome and surround result in a linear response and an exceptionally good off axis response.

Note the smooth roll off on the low end, making this tweeter a good choice for simple slopes

A specially designed venting system uses a needle to cut down on turbulence in the air cavity. Better dynamics are achieved by not using ferrofluid, voice coil cooling is performed by the venting system and conduction through copper rings. The new SD-2 neodymium magnet system improves transient response.

TECHNICAL DATA:







V.C. diameter 28 mm




Net weight 0.42 kg

D2905/9900

Revelator Dome Tweeter

The D2905/9900 is our state of the art tweeter. This “revelation” is a 1" textile dome tweeter that will reach new borders within high-end loudspeaker drive units. The new magnet system with SD caps and rings that eliminate the electrical phase shift. The new chamber design reduces air noises and compression. The 130mm machined aluminum front plate has more controlled directivity (down to 2Khz).

The textile dome is hand coated and a special device is placed behind it to reduce dynamic compression.

TECHNICAL DATA:



DC resistance 4.7 Ω


Power [email protected]


V.C. diameter 28 mm

V.C. height 3.3mm

Air gap height 2.5mm

Lin. & max. excursion ±0.4/ ±1.5 mm

Air gap flux density -

BL 3.5 Tm


Net weight 0.8 kg

12M/4631G 4Ω

Revelator 4.5” Midrange

The 12M/4631G is a Revelator driver using the “slit cone” technology. Some of the slits are used to control cone resonance and the other set of slits add rigidity. This speaker also has the new dynamic linear suspension for lower compression and higher linearity. Every facet of this driver is designed to reduce resonance in all structures. A neodymium magnet has been chosen to reduce the depth, yet increase the magnetic energy.

TECHNICAL DATA:





Power 12dB@Hz 40W


V.C. diameter 38 mm

V.C. height -

Air gap height -

Lin. & max. excursion ±3 & ±7mm



Net weight 0.6 kg

Vas 2.4 ltrs

Qms 5.57

Qes 0.35

Qts 0.33

15M/4531K 4Ω

The 15M/4531K is a 5 ½” Revelator midrange. It features a slit-paper non-resonant cone and dust cap structure, dynamic linear suspension,

SD-1 magnet system, “Grasshopper” cast chassis with maximized air flow, glass fiber voice coil former and resonance terminating mounting system.

The 15M/4531K is intended for use as a midrange, with a usable frequency range between 100Hz and 6kHz. As you can see from the response curve, this speaker has a lot of energy in the upper frequency range.

TECHNICAL DATA:





Power 12dB@Hz 60W


V.C. diameter 38 mm

V.C. height 11 mm

Air gap height 5 mm

Lin. & max. excursion ±3 & ±8mm



Net weight 1.6 kg

Vas 24 ltrs

Qms 4.8

Qes 0.24

Qts 0.23

15W/4531G-00 4Ω

The 15W/4531G-01 is a 5 ½”

Revelator mid/woofer. It features a slit-paper uncoated non-resonant cone and dust cap structure, dynamic linear suspension, SD-1 magnet system,

“Grasshopper” cast chassis with maximized air flow, glass fiber voice coil former and resonance terminating mounting system. The 15W/4531G provides a more extended frequency response than it’s brothers, but still fantastic bass down to the mid 50’s in a vented enclosure. This version is only available in 4 ohm.

TECHNICAL DATA:





Power 12dB@Hz 60W


V.C. diameter 38 mm

V.C. height 17.5 mm

Air gap height 5 mm




Net weight 1.6 kg

Vas 15.8 ltrs

Qms 4.6

Qes 0.34

Qts 0.32

15W/8530K-00/01

The 15W/8530K-01 is a 5 ½”

Revelator mid/woofer. It features a non-resonant cone and dust cap structure, dynamic linear suspension,

SD-1 magnet system, “Grasshopper” cast chassis with maximized air flow and resonance terminating mounting system.

Less resonance in all structures, lower compression and higher linearity, faster termination of excess energy and higher sound pressure capability make the 15W have more musical and dynamic capability than any other 5 ½” we know of. Wonderful bass in a small box!

TECHNICAL DATA:

Sensitivity 2.83V/1M 85.5/84.5dB

Free air resonance Fs 30/32 Hz



Power 12dB@Hz 60W


V.C. diameter 38 mm

V.C. height 18 mm

Air gap height 5 mm


Force factor BL Product 7/5.9 Tm


Net weight 1.7/1.2 kg

Vas 27.4/24 ltrs

Qms 4.9/5.23

Qes 0.29/0.44

Qts 0.27/0.41

18W/4531G 4Ω

The 18W/4531G-00 is a 7” Revelator mid/woofer. It features a non-resonant cone and dust cap structure, dynamic linear suspension, SD-1 magnet system,

“Grasshopper” cast chassis with maximized air flow and resonance terminating mounting system. Less resonance in all structures, lower compression and higher linearity, faster termination of excess energy and higher sound pressure capability. The

18W/4531G should have an F3 of about

65Hz sealed and 40Hz vented. This is a popular driver for automotive applications.

TECHNICAL DATA:





Power 70W


V.C. diameter 38 mm

VC height 17.5 mm

Air gap height 5

Lin. & max. excursion ±6.5 / ±11 mm



Net weight 1.7 kg

Vas 41.9 ltrs

Qms 5.2

Qes 0.38

Qts 0.35

18W/8531G 8Ω

The 18W/8531G-00 is a 7” Revelator mid/woofer. It features a non-resonant cone and dust cap structure, dynamic linear suspension, SD-1 magnet system,

“Grasshopper” cast chassis with maximized air flow and resonance terminating mounting system. Less resonance in all structures, lower compression and higher linearity, faster termination of excess energy and higher sound pressure capability. The

18W/8531G should have an F3 of about

50Hz sealed and 35Hz vented.

TECHNICAL DATA:





Power 60W


V.C. diameter 38 mm

VC height 18 mm

Air gap 5 mm




Net weight 1.7 kg

Vas 58.2 ltrs

Qms 5.1

Qes 0.39

Qts 0.36

22W/4851T 4Ω

The 22W/4851T is a new addition to the Revelator line. This robust 8" woofer was designed to provide deep and accurate bass in a small enclosure.

This woofer features a 2" voice coil on a titanium former, a low loss linear suspension and symmetric drive motor.

The deep set hard paper cone is attached to the frame with a minimal reflection rubber surround. The 9mm

X-max insures good linear travel.

We suggest a 1.2 cubic foot enclosure with a 2"Ø vent by 8" long for and F3 of 50Hz.

TECHNICAL DATA:





Power 170 W


V.C. diameter 50 mm

2

VC height 24 mm

Air gap 6 mm




Net weight 3.6 kg

Vas 126 ltrs

Qms 5.2

Qes 0.23

Qts 0.22

22W/8851T 8Ω





We suggest a 1.2 cubic foot enclosure with a 2.5"Ø vent by 8" long for and F3 of 38Hz.

TECHNICAL DATA:





Power 170 W


V.C. diameter 50 mm

VC height 24 mm

Air gap 6 mm




Net weight 3.6 kg

Vas 126 ltrs

Qms 5.1

Qes 0.26

Qts 0.25

22W/8857T 8

The 22W/885TT is a new addition to the Revelator line. This robust 8" woofer was designed to provide deep and accurate bass in a small enclosure.


The deep set black aluminum cone is attached to the frame with a minimal reflection rubber surround. The 9mm


We suggest a 1.2 cubic foot enclosure with a 2" Ø vent by 8" long for and F3 of 38Hz.

TECHNICAL DATA:





Power 170 W

2 Effective cone area 220 cm

V.C. diameter 50 mm

VC height 24 mm

Air gap 6 mm




Net weight 3.6 kg

Vas 87.7 ltrs

Qms 4.9

Qes 0.32

Qts 0.30

26W/8861T 8Ω





We suggest a 2.75 cubic foot enclosure with a 3"Ø vent by 9.5" long for and F3 of 30Hz.

TECHNICAL DATA:





Power 170 W


V.C. diameter 50 mm

VC height 24 mm

Air gap 6 mm




Net weight 3.7 kg

Vas 234 ltrs

Qms 5.2

Qes 0.33

Qts 0.31

26W/4867T 4Ω

The 26W/4867T a new black

Aluminum cone woofer. Aluminum is a good material for subwoofer cones, very stiff and light. These cones reduce distortion and also help cool the voice coil, by conducting heat away from the coil. This woofer has a low loss suspension for increased bass response and the SD-1 motor system for less intermodulation distortion. Very rigid cast frame, large windows.

We recommend a 2.5 cubic foot enclosure with a 3" diameter vent by

10" long, the F3 would be about 29Hz.

TECHNICAL DATA:





Power 170 W


V.C. diameter 50 mm

VC height 24 mm

Air gap 6 mm




Net weight 3.7 kg

Vas 223 ltrs

Qms 5.8

Qes 0.31

Qts 0.29

26W/8867T 8Ω

The 26W/8867T a new black

Aluminum cone woofer. Aluminum is a good material for subwoofer cones, very stiff and light. These cones reduce distortion and also help cool the voice coil, by conducting heat away from the coil. This woofer has a low loss suspension for increased bass response and the SD-1 motor system for less intermodulation distortion. Very rigid cast frame, large windows.

We recommend a 2.3 cubic foot enclosure with a 3" diameter vent by

11" long, the F3 would be about 29Hz.

TECHNICAL DATA:





Power 170 W


V.C. diameter 50 mm

2

VC height 24 mm

Air gap 6 mm




Net weight 3.7 kg

Vas 179 ltrs

Qms 4.5

Qes 0.31

Qts 0.29

23W/4557T 4Ω

The 23W/4557T is a very high end subwoofer, designed to be used with a passive radiator in a small enclosure.

This sub has a very rigid aluminum cone, low loss rubber surround and cast frame.

The passive radiator is similar, but with a weight attached to the bass of the cone.

The 23W/4557T is using the SD-1 motor system. There are gold plated binding posts and the woofer is covered by a decorative rubber cap.

Frequency response with the passive is down to 25Hz. One cubic foot sealed has an F3 of 33Hz. Also in black cone.

TECHNICAL DATA:





Power 225 W


V.C. diameter 50 mm

2

VC height 34 mm

Air gap 8 mm




Net weight 4.6 kg

Vas 45 ltrs

Qms 4.8

Qes 0.52

Qts 0.47

Black cone part# 23W/4557T-02

23W/0-00 Passive

This is the passive radiator intended for use with the 23W/4557T active woofer. We recommend putting both in a 1.0 cubic foot enclosure. This should yield a bass response down to

25Hz. The woofer should still be linear at 180 watts and have an output of about 104dB.

The curve below is a simulation of the woofer and passive radiator in a 1.0

cubic foot box. This was done in Bass

Box Pro by Harris Technologies.

Also in black cone.

TECHNICAL DATA:

Sensitivity 2.83V/1M - dB


DC resistance - ohm

V.C. inductance - mH

Power - W


V.C. diameter - mm

2

VC height -

Air gap max. excursion ±20 mm

Force factor BL Product - Tm


Net weight 1.2 kg

Vas 43.3 ltrs

Qms 11.5

Qes -

Qts -

Black cone part# 23W/0-00-02

D2008/8512

Similar to the D2008, but with several improvements, a foam impregnated front face plate and a lower resonance.

Double chambered 3/4" damped textile dome tweeter with the same diaphragm and voice coil as the D2008.

The lower resonance of this driver will allow it to be crossed over lower than most other 3/4" dome tweeters, yet retain the low distortion and clarity of a

3/4" dome. We recommend a steeper x-over slope be used when the x-over point is below 3KHz.

TECHNICAL DATA:





Power 12dB@Hz 150W@4K


V.C. diameter 19 mm

V.C. height 3.1 mm

Air gap height 2 mm




Net weight 0.4 kg

Vas -

Qms 1.26

Qes 1.24

Qts 0.63

D2010/8513

Similar to the D2008, but with several improvements, a foam impregnated front face plate and a lower resonance.

Double chambered 3/4" damped textile dome tweeter with the same diaphragm and voice coil as the D2008.

The lower resonance of this driver will allow it to be crossed over lower than most other 3/4" dome tweeters, yet retain the low distortion and clarity of a

3/4" dome. We recommend a steeper x-over slope be used when the x-over point is below 3KHz.

TECHNICAL DATA:







V.C. diameter 19 mm

V.C. height 3.1 mm

Air gap height 2 mm




Net weight 0.4 kg

Vas -

Qms 1.26

Qes 1.24

Qts 0.63

D2905/9300

1" Dome Tweeter

The D2905/9300 is a 1” textile dome tweeter with a very flat frequency response and low distortion. The

D2905/9300 achieves a lower resonance and increased clarity by using several coatings of damping material on the dome and chambering behind the dome.

Both these damping factors and the use of a light magnetic fluid, reduce the resonances as much as possible, while reducing compression affects. this tweeters linear response and openness make it a good choice for any system.

TECHNICAL DATA:







V.C. diameter 28 mm

V.C. height 3.3 mm





Net weight 0.7 kg

Vas -

Qms 0.94

Qes 0.72

Qts 0.41

D2905/9500

1" Dome Tweeter

The D2905/9500 is similar to the

D2905/9300, but with non-resonant chamber. The optimized pole piece geometry reduces flow resistance and the anti-resonator-plug in the rear chamber eliminates turbulence. A light ferrofluid is used in the air gap to ensure optimal linear mechanical behavior and minimal micro-dynamic non-linearity. This tweeter has a smooth transparent sound and very low levels of distortion. A perfect choice for any high end system.

TECHNICAL DATA:







V.C. diameter 28 mm

V.C. height 3.3 mm





Net weight 0.7 kg

Vas -

Qms 1.04

Qes 0.60

Qts 0.38

D2905/9700

1” Dome Tweeter

The D2905/9700 uses the same hand coated dome and voice coil of the

D2905/9500, but uses the motor system of the Revelator. The Symmetric Drive technology eliminates almost all electrical phase shift. The carefully machined top plate minimize air noise and compression. Copper caps act as heat conductors. High power handling is achieved without ferrofluid and improves micro-dynamic linearity. The tweeter has excellent dynamic and detailing capability.

TECHNICAL DATA:



DC resistance 4.7 Ω


Power [email protected]


V.C. diameter 28 mm

V.C. height 3.3 mm


Lin. & max. excursion ±0.4/ ±1.5 mm

BL 3.5 Tm


Net weight 0.7 kg

Vas -

Qms 3.45

Qes 0.54

Qts 0.47

D2904/9800 4Ω

The D2904/9800 is a high-end 1” aluminum dome tweeter. The magnet system uses the Symmetric Drive technology that almost eliminates electrical phase shift. The specially designed chamber reduces air noise and compression. The geometry of the dome causes the “break-up” to appear beyond the audible range. A specially designed diffusor is used to equalize the response in the upper octave. The tweeter has a very clear and open sound.

TECHNICAL DATA:







V.C. diameter 28 mm

V.C. height 2.5 mm





Net weight 0.7 kg

Vas -

Qms 3.09

Qes 0.84

Qts 0.66

D3806/8200

1.5" Dome Mid/Tweeter

The D3806/8200 is a 1.5” textile dome mid/tweeter. The large dome allows for a lower crossover point. Large dome typically have better transient response too. This tweeter is a good choice for use in a system where a lower crossover point is required, or where an upper mid is needed.

This tweeter has the SD motor system for reduced distortion and a tuned rear chamber. Flange is 125mm in diameter,

91mm cut out diameter and 47mm depth.

TECHNICAL DATA:







V.C. diameter 38 mm

V.C. height 3.2 mm





Net weight 1.1 kg

Vas -

Qms 0.93

Qes 1.00

Qts 0.48

18W/8535

7" Carbon/Paper Woofer

The 18W/8535 woofer features the

SD-1 magnet system which almost eliminates modulation and dynamic distortion and reduce clipping when the drivers is taken beyond linear excursion.

The carbon fiber filled paper cone is impregnated and coated to damp resonance. The low loss rubber surround combines dynamic linearity with low coloration. The smaller magnet increases the Qts making this driver a good choice for a sealed enclosure.

TECHNICAL DATA:





Power 70W


V.C. diameter 38 mm

V.C. height 15 mm

Air gap height 5 mm




Net weight 2.5 kg

Vas 71.2 liters

Qms 2.50

Qes 0.45

Qts 0.38

18W/8542

7" Paper Cone Woofer

The 18W/8542 is a classic paper cone woofer with foam surround. The back coated paper cone delivers smooth and warm sound reproduction. The speaker is intended for high end 2-way systems in bass reflex enclosures. This woofer has the large Symetric Drive (SD) magnet system for reduced distortion.

The surround is made of double coated foam material with long term stability.

A coating is used to dampen unwanted resonances where the surround is attached to the cone.

TECHNICAL DATA:





Power 70W


V.C. diameter 42 mm

V.C. height 19 mm

Air gap height 6 mm

Lin. & max. excursion ±6.5 / ±10mm



Net weight 2.3 kg

Vas 47.9 liters

Qms 1.7

Qes 0.26

Qts 0.23

18W/8545

7" Carbon fibre Paper Woofer

This 7" features the heavily damped and carbon fibre impregnated paper cone that dampens resonances normally associated with stiff cones. The magnet system is the new SD-1 system which eliminates modulation and dynamic distortion, as well as clipping distortion created as it exceeds its maximum linear excursion. These designs all together make a drive unit with a very “open” sound with excellent detailing combined with low coloration and very precise imaging. Cast frame, rubber surround.

TECHNICAL DATA:





Power 100W


V.C. diameter 42 mm

2

V.C. height 19 mm

Air gap height 6 mm




Net weight 2.3 kg

Vas 47.6 liters

Qms 2.30

Qes 0.30

Qts 0.27

18W/8545K

7" Carbon fibre Paper Woofer

This 7" features the heavily damped and carbon fibre impregnated paper cone that dampens resonances normally associated with stiff cones. The magnet system is the new SD-1 system which eliminates modulation and dynamic distortion, as well as clipping distortion created as it exceeds its maximum linear excursion. This driver uses a fiberglass voice coil former.

Try it in a 1/2 cubic foot box with a

1.5" diameter vent by 5.2" long, f3 48Hz.

TECHNICAL DATA:





Power 100W


V.C. diameter 42 mm

2

V.C. height 19 mm

Air gap height 6 mm




Net weight 2.4 kg

Vas 46.4 liters

Qms 5.20

Qes 0.30

Qts 0.28

D2606/9200 6Ω

The D2606/9200 is a 1" coated silk fabric dome tweeter. This tweeter uses ferrofluid to cool the voice coil and reduce the resonance peak. The linear response face plate provides a very smooth response at a fairly high sensitivity. The voice coil is attached to the leads by a high power braided tinsel lead wire. A damped cavity in the pole pieces reduces reflections and lowers the resonance frequency. The tweeter has field repairable voice coil assembles (600058). This tweeter was previously produced under the part number D27TG15-06 and could be a good replacement for D26TG05 tweeters too, but with 5 screw holes instead of 4.

TECHNICAL DATA:







V.C. diameter 26 mm

V.C. height 1.6 mm








Flange thickness 4.2 mm

Depth 27.1 mm

Screw Circle 94 mm

D2606/9220 6Ω

The D2606/9220 is a 1" coated silk fabric dome tweeter. This tweeter uses ferrofluid to cool the voice coil and reduce the resonance peak. The large rear chamber provides a low resonance frequency and reduces reflections. The low fs allows for a lower crossover point. by a high power braided tinsel lead wire. The tweeter has field repairable voice coil assembles

(600058). This tweeter can be used to be produced under the part number

D27TG35-06 and is a good replacement for older D26TG35 tweeters. It can also replace the D27TG45, but with 4 screw holes instead of 5.

TECHNICAL DATA:







V.C. diameter 26 mm

V.C. height 2.1 mm









Depth 38.9 mm

Screw Circle 94 mm

D2604/8330 4Ω

The D2604/8330 is a 1" textile dome with a large roll surround which provides extended frequency response above

40kHz. The double magnet provide greater efficiency as well as a chamber to reduce reflections and lower the resonance frequency. The tweeter uses high temperature copper-clad aluwire.

The tweeter also has a well behaved roll off on the low end, which should allow the tweeter to use more simplified crossovers. The off axis response is also very good, making this tweeter a good choice for automotive systems too.

The low fs allows for a lower crossover point.

TECHNICAL DATA:







V.C. diameter 25 mm

V.C. height 2.0 mm


Linear excursion ±0.3 mm







Depth 54.6 mm

Screw Circle 92 mm

D2608/9130 8Ω

The D2608/9130 has a very light

1" textile dome with high internal damping. The optimized magnet system feature dual magnets, low compression and magnetic cooling fluid. The magnet system is designed to reduce reflections and turbulence. The face plate is black die cast aluminum. The 8 ohm impedance, yet high efficiency of

91.3dB makes this a rather unique tweeter. The low resonance frequency and magnetic fluid will allow for a low crossover point. This tweeter is a good choice for all high end speaker systems.

TECHNICAL DATA:







V.C. diameter 26 mm

V.C. height 1.5 mm





Moving mass incl. air - g




Depth 32.3 mm

Screw Circle 92 mm

R2604/8320 4Ω

The R2604/8320 features the unique dual ring radiator diaphragm made from coated silk fabric. The tweeter also uses a patented wave guide center plug to reduce distortion. The low resonance frequency allows for a low crossover point. A special chamber lowers the fs and reduces internal reflections.

The frequency range extends beyond

40kHz! Copper-clad aluwire assures good power handling at lower crossover points. This tweeter has quickly become a favorite with loudspeaker designers. The D2604/8320 used to be produced under the part number XT25TG30.

TECHNICAL DATA:







V.C. diameter 25 mm

V.C. height 2.2 mm









Depth 39.8 mm

Screw Circle 92 mm

R2604/8330 4Ω

The R2604/8330 features the unique dual ring radiator diaphragm made from coated silk fabric. The tweeter also uses a patented wave guide center plug to reduce distortion. The low resonance frequency allows for a low crossover point. A special chamber lowers the fs and reduces internal reflections.

The frequency range extends beyond

40kHz! Copper-clad aluwire assures good power handling at lower crossover points. The Double magnet increases efficiency and extends the upper frequency range. The

D2604/8330 used to be produced under the part number XT25BG60.

TECHNICAL DATA:







V.C. diameter 25 mm

V.C. height 2.2 mm









Depth 54.6 mm

Screw Circle 92 mm

D7608/9200-10 8Ω

The D7608/9200-10 is one of the last remaining 3" textile dome tweeters. A textile dome mid is a perfect choice for upper midrange where fast action is required.

The pre-coated fabric dome has a very smooth and natural sounding response. The 3" voice coil provides good transient response and heat dispersion. An internal grill is used to protect the dome from being pushed in. The rear plate is perforated with holes, so the midrange requires the use of a 1 to 2 liter sealed and stuffed chamber (not included). This midrange has exceptional off axis response and would be good in a car if you can work out a chamber.

TECHNICAL DATA:





Power 12dB@Hz 80W@500Hz


V.C. diameter 76 mm

V.C. height 2.9 mm


Linear excursion ±0.4.5 mm






Depth 25.6 mm

Screw Circle 134 mm

***Must use with 1 to 2 liter chamber

10F/4424G 4Ω

4" Fiberglass Cone Midrange

The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves, and the vented motor system minimizes power compression. The combined result is a very open and dynamic sound. This midrange also features a strong neodymium magnet, NR surround and aluminum chassis. In 1 liter sealed your

F3 is 275Hz, in 1.2 liters vented, 1"vent diameter x 3", your F3 is 125Hz. This driver has a very extended response.

TECHNICAL DATA:





Power RMS 15W


V.C. diameter 20 mm

V.C. height 9.2 mm

Air gap height 4 mm




Net weight 0.3 kg

Vas 2.0 liters

Qms 3.20

Qes 0.32

Qts 0.29

Cms 1.1 mm/N

10F/8424G 8Ω

4" Fiberglass Cone Midrange

The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves, and the vented motor system minimizes power compression. The combined result is a very open and dynamic sound. This midrange also features a strong neodymium magnet, NR surround and aluminum chassis. In 1 liter sealed your

F3 is 275Hz, in 1.2 liters vented, 1"vent diameter x 3", your F3 is 125Hz. This driver has a very extended response.

TECHNICAL DATA:





Power RMS 15W


V.C. diameter 20 mm

V.C. height 9.2 mm

Air gap height 4 mm




Net weight 0.3 kg

Vas 2.1 liters

Qms 3.49

Qes 0.41

Qts 0.37

Cms 1.14 mm/N

15M/4624G 4Ω

5.25" Fiberglass Cone Mid

The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves. The phase plug improves linearity and eliminates distortion caused by reflections that occur behind dust caps. The coated foam surround improves sensitivity.

Highlights: Aluminum Chassis,

Fiberglass cone, coated foam surround, raised spider, aluminum shorting ring

Flange 149mm, cutout 114mm, depth

60.9mm. Use in small sealed enclosure.

TECHNICAL DATA:





Power RMS 75W


V.C. diameter 25 mm

V.C. height 8 mm

Air gap height 5 mm




Net weight 1.0 kg

Vas 3.7 liters

Qms 5.62

Qes 0.47

Qts 0.43

Cms 0.41 mm/N

12W/4524G 4Ω

4.5" Fiberglass Cone Woofer

The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves, and the vented motor system minimizes power compression. Suitable as small woofer or midrange in a larger system.

Driver Highlights: Aluminum

Chassis, Fiberglass cone, NR rubber surround, Raised spider

, shorting ring

Flange 124.7mm, cutout 100mm, depth 58.4mm. Use vented for use as a woofer or sealed for use as a midrange.

TECHNICAL DATA:





Power RMS 40W


V.C. diameter 25 mm

V.C. height 10 mm

Air gap height 4 mm

Lin. & max. excursion ±3 / ±9mm



Net weight 1.0 kg

Vas 8.2 liters

Qms 3.35

Qes 0.30

Qts 0.27

Cms 1.67 mm/N

12W/8524G 8Ω


The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves, and the vented motor system minimizes power compression. Suitable as small woofer or midrange in a larger system.



, shorting ring

Flange 124.7mm, cutout 100mm, depth 58.4mm. Use vented for use as a woofer or sealed for use as a midrange.

TECHNICAL DATA:





Power RMS 40W


V.C. diameter 25 mm

V.C. height 10 mm

Air gap height 4 mm




Net weight 1.0 kg

Vas 8.2 liters

Qms 3.42

Qes 0.35

Qts 0.32

Cms 1.67 mm/N

15W/4434G 4Ω


The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves, and the vented motor system minimizes power compression. The combined result is a very open and dynamic sound.



, shorting ring


60.9mm. In 4 liter box with 1.5" diameter vent by 4" long, F3 is 80Hz.

TECHNICAL DATA:





Power RMS 60W


V.C. diameter 32 mm

V.C. height 13.6 mm

Air gap height 5 mm




Net weight 1.2 kg

Vas 12.8 liters

Qms 3.69

Qes 0.22

Qts 0.21

Cms 1.43 mm/N

15W/8434G 8Ω




Chassis, Fiberglass cone, NR rubber surround, raised spider, shorting ring


60.9mm. In 4 liter box with 1.5" diameter vent by 4" long, F3 is 80Hz.

TECHNICAL DATA:





Power RMS 60W


V.C. diameter 32 mm

V.C. height 13.4 mm

Air gap height 5 mm




Net weight 1.2 kg

Vas 12.8 liters

Qms 3.74

Qes 0.27

Qts 0.25

Cms 1.43 mm/N

18W/4434G 4Ω





, shorting ring

Flange 179.6mm, cutout 144.3mm, depth 73.2mm. In 15 liter box with 2" diameter vent by 4.5" long, F3 is 55Hz.

TECHNICAL DATA:





Power RMS 55W


V.C. diameter 32 mm

V.C. height 13.6 mm

Air gap height 5 mm




Net weight 1.3 kg

Vas 20.7 liters

Qms 7.81

Qes 0.37

Qts 0.35

Cms 0.79 mm/N

18W/8434G 8Ω





, shorting ring

Flange 179.6mm, cutout 144.3mm, depth 73.2mm. In 15 liter box with 2" diameter vent by 4.5" long, F3 is 55Hz.

TECHNICAL DATA:





Power RMS 55W


V.C. diameter 32 mm

V.C. height 13.4 mm

Air gap height 5 mm




Net weight 1.3 kg

Vas 19.5 liters

Qms 7.58

Qes 0.46

Qts 0.43

Cms 0.74 mm/N

22W/4534G 4Ω

8" Fiberglass Cone Woofer





84.5mm. In 35 liter box with 2" diameter vent by 4" long, F3 is 45Hz.

TECHNICAL DATA:





Power RMS 70W


V.C. diameter 38 mm

2

V.C. height 17.3 mm

Air gap height 6 mm




Net weight 2.1 kg

Vas 95 liters

Qms 3.70

Qes 0.37

Qts 0.34

Cms 1.23 mm/N

22W/8434G 8Ω



Driver Highlights: Aluminum Chassis,

Fiberglass cone, NR rubber surround,

Raised spider



TECHNICAL DATA:





Power RMS 70W


V.C. diameter 38 mm

2

V.C. height 17.5 mm

Air gap height 6 mm




Net weight 2.1 kg

Vas 118.3 liters

Qms 5.04

Qes 0.37

Qts 0.34

Cms 1.52 mm/N

26W/4534G 4Ω







TECHNICAL DATA:





Power RMS 70W


V.C. diameter 38 mm

V.C. height 18 mm

Air gap height 6 mm




Net weight 2.9 kg

Vas 156 liters

Qms 9.57

Qes 0.37

Qts 0.36

Cms 0.92 mm/N

26W/8534G 8Ω







TECHNICAL DATA:





Power RMS 70W


V.C. diameter 38 mm

2

V.C. height 18 mm

Air gap height 6 mm




Net weight 2.9 kg

Vas 150 liters

Qms 9.12

Qes 0.42

Qts 0.40

Cms 0.95 mm/N

26W/4558T 4Ω

10" Aluminum Subwoofer

This Discovery 10" subwoofer has many fantastic features. The cone is black anodized aluminum for stiffness.

The dust cap is a layered paper and fiberglass. An aluminum shorting ring and aluminum pole piece extension is used to reduce distortion and power compression. A Titanium voice coil former improves power handling. The voice coil is vented below the spider and behind the dust cap for added VC cooling. Us in 2 cubic feet with 3" vent by 10" long for an F3 of 30Hz.

TECHNICAL DATA:





Power RMS 150W


V.C. diameter 51 mm

2

V.C. height 33 mm

Air gap height 8 mm

Lin. & max. excursion ±12.5/±28mm



Magnet weight 2.25 kg

Vas 94.9 liters

Qms 5.56

Qes 0.33

Qts 0.31

Cms 0.55 mm/N

26W/0-00

10" Aluminum Cone

Passive Radiator

This passive is built similarly to the active woofer. Same black anodized aluminum cone, paper/fiberglass dust cap, cast frame, low damping large roll rubber surround and Nomex spider. In place of the voice coil, a weight is added to tune the passive radiator to 11Hz.

More mass could be added to the weight, but too much mass will make the passive sluggish and may reduce the live of the product.

TECHNICAL DATA:



Max excursion ±28mm


Vas 95 liters

Qms 13.7

Cms 0.55 mm/N

Rms 1.97 kg/s

When paired with the 26W/4558T woofer in a 1 cubic foot box and an amplifier with a 25Hz boost, your F3 will be about 35Hz. Without a boost the F3 is about 45Hz.

When using the 1 cubic foot box with passive radiator in a car, without any boost and with 6dB of cabin gain, your F3 is about 19Hz. This should be very impressive in a car environment.

30W/4558T 4Ω

12" Aluminum Subwoofer

This Discovery 12" subwoofer has many fantastic features. The cone is black anodized aluminum for stiffness.

The dust cap is a layered paper and fiberglass. An aluminum shorting ring and aluminum pole piece extension is used to reduce distortion and power compression. A Titanium voice coil former improves power handling. The voice coil is vented below the spider and behind the dust cap for added VC cooling. Us in 2.5 cubic feet with 3" vent by 12" long for an F3 of 30Hz.

TECHNICAL DATA:





Power RMS 150W


V.C. diameter 51 mm

2

V.C. height 33 mm

Air gap height 8 mm

Lin. & max. excursion ±12.5/ ±28mm



Magnet weight 2.25 kg

Vas 197 liters

Qms 5.01

Qes 0.34

Qts 0.32

Cms 0.65 mm/N

30W/0-00

12" Aluminum Cone

Passive Radiator

This passive is built similarly to the active woofer. Same black anodized aluminum cone, paper/fiberglass dust cap, cast frame, low damping large roll rubber surround and Nomex spider. In place of the voice coil, a weight is added to tune the passive radiator to 11Hz.

More mass could be added to the weight, but too much mass will make the passive sluggish and may reduce the live of the product.

TECHNICAL DATA:

Free air resonance Fs 9.5 Hz


Max excursion ±28mm


2

Vas 200 liters

Qms 14

Cms 0.65 mm/N

Rms 1.84 kg/s

When paired with the 30W/4558T woofer, we recommend a 2.0 to 2.5

cubic foot box for an F3 of about 30Hz. This F3 is about the same wether you use a boost on the amp or not. If not using a 25Hz boost, you will have a leaner and tighter bass and with the boost you will have a more pronounced bass.

You can also use this passive with the 26W/4558T in a 1.5 cubic foot box with a similar F3 of 35Hz, but with a 2dB gain in efficiency from the 10" passive.

P13WH00 8Ω

5" Poly Cone Woofer

This classic 5" Vifa woofer now being built by Scan-speak was used in many

DIY and commercial systems over the years. The P13WH00 has a mineral filled poly cone, rubber surround and cast frame. You might choose this as a replacement for similar Vifa drivers in the 140mm frame size.

We understand this to be the last production run of this speaker.

You can use this driver in a 6 liter box with a 1.5" diameter port by 4.5" long for an F3 of 83Hz.

TECHNICAL DATA:





Power RMS 40W


V.C. diameter 25 mm

V.C. height 14 mm

Air gap height 6 mm

Linear excursion ±4mm



Net weight - kg

Vas 10 liters

Qms 1.38

Qes 0.43

Qts 0.33

Cms - mm/N

P17WJ00 8Ω

6.5" Poly Cone Woofer

This classic 6.5" Vifa woofer now being built by Scan-speak was perhaps the most popular driver in the world at one time. This classic woofer was used in many commercial products. The

P17WJ00 has a mineral filled poly cone, rubber surround and cast frame. This woofer should be considered as a good replacement for other classic Vifa and

Seas woofers in the same frame size.

You can use this woofer in a 15 liter box with a 2" diameter port by 7" long for an F3 of 55Hz.

TECHNICAL DATA:





Power RMS 40W


V.C. diameter 32 mm

2

V.C. height 14 mm

Air gap height 6 mm




Net weight - kg

Vas 34.7 liters

Qms 1.55

Qes 0.45

Qts 0.35

Cms - mm/N

P21WO20 8Ω

8" Poly Cone Woofer

This classic 8" Vifa woofer now being built by Scan-speak. This classic woofer was used in many commercial products.

The P21WO20 has a mineral filled poly cone, rubber surround and cast frame.

This woofer should be considered as a good replacement for other classic Vifa and Seas woofers in the same frame size.

You can use this woofer in a 45 liter box with a 3" diameter port by 8" long for an F3 of 40Hz.

TECHNICAL DATA:





Power RMS 80W


V.C. diameter 40 mm

V.C. height 14 mm

Air gap height 6 mm




Net weight - kg

Vas 113 liters

Qms 1.6

Qes 0.41

Qts 0.33

Cms - mm/N

History

Founded in 1970, Scan-Speak still resides at our original address in Videbaek, Denmark. Located in the heart of the

Jutland peninsula, our acoustic engineers adhere to our legendary policy of "Never compromise". We never compromise on our product quality, sound quality or pursuit of perfection in a given application. We set the loudspeaker industry's gold standard for audiophiles, and are constantly viewed as a market benchmark by other high-end speaker manufacturers.

For close to 40 years, Scan-Speak has been on a quest to create transducers that reveal the finest details in recordings, concealing nothing from the listener. This quest has resulted in several revolutionary inventions, where distortion in the magnet systems and the moving parts of the speaker is minimized. Our philosophy is simple: the emitted sound must be dynamic, giving a transient response and providing tonal balance.

Scan-Speak transducers have righteously been called "the best that money can buy", and we agree fully. All our transducers are hand-built with the utmost attention to quality at their core. Their prices reflect this, providing solutions targeted towards high-end audiophile applications.

Needless to say, Scan-Speak is dedicated to proving an unwavering high-quality in manufacturing.

820012 Autosound

5" Car Component System

» 130mm Mid/Woofers "EURO-DIN"

» Aluminum Die Cast Basket

» Neodymium Magnet System

» Vented Pole Piece

» Black Coated NRSC* Fiberglass

Cone

» Low Loss Rubber Surround

» 19mm Ring Dome Tweeters

» Wedge Housing

» Flange and Nut for Flush Mounting

» Crossovers (2nd Order @ 2500Hz)

» Grill, Cables and Screws

*Non-Resonant-Suspension-Coupled

Reduces breakup modes.

The Discovery car audio systems have been designed with the same engineering and attention to detail that has made their home speakers famous.

The standard frame size of the woofer and the two mounting options for the tweeter should make for an easy installation.

820013 Autosound

6" Car Component System

» 165mm Mid/Woofers "EURO-DIN"

» Aluminum Die Cast Basket

» Neodymium Magnet System

» Vented Pole Piece

» Black Coated NRSC* Fiberglass

Cone

» Low Loss Rubber Surround

» 19mm Ring Dome Tweeters

» Wedge Housing

» Flange and Nut for Flush Mounting

» Crossovers (2nd Order @ 3000Hz)

» Grill, Cables and Screws

*Non-Resonant-Suspension-Coupled

Reduces breakup modes.

The Discovery car audio systems have been designed with the same engineering and attention to detail that has made their home speakers famous.

The standard frame size and multiply mounting options of the woofer and the two mounting options for the tweeter should make for an easy installation.

SYSTEM DATA:

Nominal Impedance 4 ohm


Frequency Range 70Hz - 28kHz

Crossover frequency 2500Hz/12dB

WOOFER DATA:


Effective cone area Sd 80 cm 2

V.C. diameter 32 mm




Vas 4.6 liters

Qms 4.41

Qes 0.65

Qts 0.57

Weight 510 g

Woofer diameter 130 mm

At mounting tabs 152 mm

Cut out diameter 113 mm

Depth 52 mm

Screw mount diameter 138 mm +2.5


TWEETER DATA:

Free air resonance Fs 1000Hz

Effective cone area Sd 3.8 cm2

Voice coil diameter 19mm

Weight 60 g

Tweeter diameter 42 mm


Depth 18 mm

Overall thickness 26 mm

Surface or Wedge mount

25.4mm = 1"

SYSTEM DATA:

Nominal Impedance 4 ohm


Frequency Range 60Hz - 28kHz

Crossover frequency 3000Hz/12dB

WOOFER DATA:


Effective cone area Sd 138 cm 2

V.C. diameter 32 mm




Vas 12.6 liters

Qms 3.06

Qes 0.56

Qts 0.48

Weight 590 g

Woofer diameter 165.5 mm


Depth 63 mm

Screw mount diameter 156.5 mm +.75


TWEETER DATA:

Free air resonance Fs 1000Hz

Effective cone area Sd 3.8 cm2

Voice coil diameter 19mm

Weight 60 g

Tweeter diameter 42 mm


Depth 18 mm

Overall thickness 26 mm

Surface or Wedge mount

25.4mm = 1"

Driver Di men sions in Mil li me ters

Unit

D2004/6020-00, R2004/6020-00

D3004/6020-00, R3004/6020-00

D3004/6020-10, R3004/6020-10

D3004/6640-00, D3004/6600-00

D3004/6620-00, D3004/6620-01

R3004/6620-00, R3004/6620-01

R2904/7000, D2904/7100

D2905/9900

D2008/8512

D2010/8513

D2905/9300, 9500, 9700

D2904/9800

D3806/8200

A

55.5

61.9

61.9

104

104

104

104

130

92

98

104.5

104.5

125

B

5

5

5

5

5

5

5.9

5

3.5

5

3

3

4

D2606/9200 Discovery



104

104

104

104

4.2

4.2

5

4.5


R2604/8320 Discovery

R2604/8330 Discovery

D7608/9200-10 Dis cov ery Mid

104

104

152

97.5

5

4

4

3.5

10F's Discovery

12MU's Illuminator

12M's Revelator

12W's Discovery

120

115.5

124.7

4

3

5

27.1

38.9

54.6

32.3

39.8

54.6

25.6

40

70

48.4

58.4

25

48

37.5

41

41

43

45

C

29.3

21.5

55.4

23

23

23

25.4mm = 1"

28.3 li ters = 1 cu bic foot

1 cu bic foot = 1728 cu bic inches

Box Vol ume = L x W x H

We can as sist you with your speaker de sign.

72

72

72

72

72

72

115.5

78

101

92

100

74

74

92

70

90

69

69

D

42.1

48.5

48.5

77

77

77

Unit

13M's Classic

15M & W's Discovery

15M's Revelator

15W's Revelator

15WU's Illuminator

18W's Discovery

18W's Revelator

18W's Classic

18WU's Illuminator

22W's Discovery

22W's Revelator

23W's Revelator

23W's Passives

Driver Di men sions in Mil li me ters

A B

130

149

148

148

149

179.6

182

177

184

225

222

255

255

6

4.8

6

6

6.5

5.2

5.5

4

7.5

5.2

7

6

6

25W's Classic

26W's Discovery

26W Dis cov ery Subwoofer

255

272

270

270

6

5.6

5

5 26W Dis cov ery Passive

26W's Revelator

30W Dis cov ery Subwoofer

30W Dis cov ery Passive

260

308

308

42

7

5

5

8 820012 & 820013 tweeter

820012 woofer

820013 woofer

Flow Re sis tor (SSV)

130

165.5

130

3.8

3.3

3

Founded in 1970, Scan-Speak is one of the oldest and most experienced loudspeaker manufacturers in the world. Their "Never Compromise" philosophy assures you as a customer that the product will be engineered and built to exceptional standards.

Please visit the Scan-speak website for a history of the company, as well as the most updated news, information and specifications.

86

100.4

135.5

70.9

124.7

144.3

80

18

52

63

19

77

70

97.3

84.5

111

135

73

C

45.5

61.9

71

71

90

73.2

228

231

240

240

228

280

280

39

113

141

109

156

158

158

185

194

225

225

D

103

114

125

125

123

144.3

www.scan-speak.dk

Scanspeak Full V10.vp

Il lu mi na tor Se ries Tweeters

S

V

Il lu mi na tor Se ries Midranges

Il lu mi na tor Se ries Woofers

Rev e la tor Se ries Tweeters

Rev e la tor Se ries Midranges

Rev e la tor Se ries Mid/Bass & Woofers

Clas sic Se ries Tweet ers

Clas sic Se ries Mid/Tweeter

Clas sic Se ries Woofers

S

V

Dis cov ery Se ries Dome Tweet ers

Dis cov ery Se ries Midranges

Dis cov ery Se ries Woofers

Dis cov ery Se ries Subwoofers and Pas sive Radiators

Dis cov ery Se ries Autosound Com po nent Systems

Clas sic Vifa Driv ers Built by Scan-Speak

Revelator Dome Tweeter

Revelator 4.5” Midrange

7" Paper Cone Woofer

7" Carbon fibre Paper Woofer

7" Carbon fibre Paper Woofer

4" Fiberglass Cone Midrange

4" Fiberglass Cone Midrange

5.25" Fiberglass Cone Mid

, shorting ring

, shorting ring

5.25" Fiberglass Cone Woofer

, shorting ring

5.25" Fiberglass Cone Woofer

6.5" Fiberglass Cone Woofer

, shorting ring

, shorting ring

8" Fiberglass Cone Woofer

8" Fiberglass Cone Woofer

10" Fiberglass Cone Woofer

10" Fiberglass Cone Woofer

10" Aluminum Subwoofer

10" Aluminum Cone

12" Aluminum Subwoofer

12" Aluminum Cone

6.5" Poly Cone Woofer

8" Poly Cone Woofer

Founded in 1970, Scan-Speak still resides at our original address in Videbaek, Denmark. Located in the heart of the

Scan-Speak transducers have righteously been called "the best that money can buy", and we agree fully. All our transducers are hand-built with the utmost attention to quality at their core. Their prices reflect this, providing solutions targeted towards high-end audiophile applications.

Needless to say, Scan-Speak is dedicated to proving an unwavering high-quality in manufacturing.

www.scan-speak.dk

Related manuals

Cambridge Audio

Sx

Crossfire

XT-PRO 8

Dragster

Neodymium Magnet Aluminum Dome