pdf040 01 409 085 EH 0912

pdf040 01 409 085 EH 0912
040-01-409-085-EH-0912.pdf
040-01-409-085-EH-0912
10W Single Output Industrial DIN Rail Power Supply
MDR-10
series
Features :
Universal AC input/Full range
Protections: Short circuit / Overload / Over voltage
Cooling by free air convection
Can be installed on DIN rail TS-35/7.5 or 15
NEC class 2 / LPS compliant
Built in DC OK active signal
LED indicator for power on
No load power consumption<0.75W
100% full load burn-in test
3 years warranty
SPECIFICATION
MODEL
OUTPUT
MDR-10-5
MDR-10-12
MDR-10-15
MDR-10-24
DC VOLTAGE
5V
12V
15V
24V
RATED CURRENT
2A
0.84A
0.67A
0.42A
CURRENT RANGE
0 ~ 2A
0 ~ 0.84A
0 ~ 0.67A
0 ~ 0.42A
RATED POWER
10W
RIPPLE & NOISE (max.) Note.2 80mVp-p
10W
10W
120mVp-p
150mVp-p
VOLTAGE TOLERANCE Note.3
5.0%
3.0%
3.0%
2.0%
LINE REGULATION
1.0%
1.0%
1.0%
1.0%
LOAD REGULATION
5.0%
3.0%
3.0%
2.0%
SETUP, RISE TIME
INPUT
10W
120mVp-p
Note.5 500ms, 30ms/230VAC
HOLD UP TIME (Typ.)
120ms/230VAC
VOLTAGE RANGE
85 ~ 264VAC
FREQUENCY RANGE
47 ~ 63Hz
1000ms, 30ms/115VAC at full load
25ms/115VAC at full load
120 ~ 370VDC
EFFICIENCY (Typ.)
77%
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
0.33A/115VAC
0.21A/230VAC
COLD START 35A/115VAC
70A/230VAC
<1mA / 240VAC
LEAKAGE CURRENT
OVERLOAD
PROTECTION
81%
81%
Above 105% rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed
13.8 ~ 16.2V
17.25 ~ 20.25V
5.75 ~ 6.75V
84%
27.6 ~ 32.4V
OVER VOLTAGE
FUNCTION
Protection type : Shut down o/p voltage, re-power on to recover
9 ~ 13.5V / 40mA
DC OK ACTIVE SIGNAL (max.) 3.75 ~ 6V / 50mA
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
11.5 ~ 16.5V / 40mA
18 ~ 27V / 20mA
-20 ~ +70 (Refer to "Derating Curve")
20 ~ 90% RH non-condensing
-40 ~ +85
, 10 ~ 95% RH
0.03%/ (0 ~ 50
Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6
UL508, TUV EN60950-1 approved, NEC class 2 / LPS compliant
SAFETY &
TEMP. COEFFICIENT
VIBRATION
SAFETY STANDARDS
WITHSTAND VOLTAGE
EMC
ISOLATION RESISTANCE
(Note 4)
EMC EMISSION
EMC IMMUNITY
MTBF
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH
Compliance to EN55011, EN55022 (CISPR22), EN61204-3 Class B, EN61000-3-2,-3
OTHERS
DIMENSION
PACKING
NOTE
I/P-O/P:3KVAC
I/P-FG:1.5KVAC
O/P-FG:0.5KVAC
Compliance to EN61000-4-2, 3, 4, 5, 6, 8, 11, EN55024,EN61000-6-1,EN61204-3, light industry level, criteria A
584K hrs min. MIL-HDBK-217F (25
22.5*90*100mm (W*H*D)
0.17Kg; 72pcs/13.2Kg/0.91CUFT
)
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
5. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.
File Name:MDR-10-SPEC 2011-05-24
040-01-409-085-EH-0912.pdf
040-01-409-085-EH-0912
MDR-10
10W Single Output Industrial DIN Rail Power Supply
Mechanical Specification
Case No. 956
series
Unit:mm
100
22.5
5 5
35
+V -V DC
OK
90
DC OK
N L
Install DIN rail TS35/7.5 or TS35/15
5 5
Block Diagram
fosc : 60KHz
DC OK
RECTIFIERS
&
FILTER
EMI
FILTER
I/P
DC OK
RECTIFIERS
&
FILTER
POWER
SWITCHING
+V
-V
DETECTION
CIRCUIT
FG
O.L.P.
CONTROL
O.V.P.
Application of DC OK Active Signal
(a) 5V signal
(b) LED
DC OK
Model
5V
12V
15V
24V
R
5.1V
(c) Relay
DC OK
R
200
1.5K
2K
3.9K
R
Model
5V
12V
15V
24V
DC OK
R
1K
2.4K
3K
4.7K
Relay
V-
V-
Model
5V
12V
15V
24V
RL
RL
120
700
700
1.2K
V-
Output Derating VS Input Voltage
Derating Curve
Ta=25
100
100
Others
90
80
80
5V
70
LOAD (%)
LOAD (%)
60
40
20
-20
0
10
20
30
40
50
AMBIENT TEMPERATURE ( )
60
70 (VERTICAL)
60
50
40
85
95
100
115
120
140
160
180
200
220
240
264
INPUT VOLTAGE (VAC) 60Hz
File Name:MDR-10-SPEC 2011-05-24
Headquarter Switzerland:
Pewatron AG
Thurgauerstrasse 66
CH-8052 Zurich
Phone +41 44 877 35 00
[email protected]
Office Germany:
Pewatron AG
Neumarkter Straße 86a
D-81673 Munich
Phone +49 89 260 38 47
[email protected]
We are here for you. Addresses and Contacts.
Sales Switzerland & Liechtenstein
Sales International Key Accounts
Postcode 3000 – 9999
Postcode 1000 – 2999
Basil Frei
Pewatron AG
Thurgauerstrasse 66
CH-8052 Zurich
Eric Letsch
Pewatron AG
Thurgauerstrasse 66
CH-8052 Zurich
Peter Felder
Pewatron AG
Thurgauerstrasse 66
CH-8052 Zurich
Phone + 41 44 877 35 18
Mobile + 41 76 279 37 26
Phone + 41 44 877 35 14
Mobile + 41 76 491 66 70
Phone + 41 44 877 35 05
Mobile + 41 79 406 49 83
[email protected]
[email protected]
[email protected]
Sales Germany
Postcode 00000 – 31999
Postcode 38000 – 39999
Postcode 80000 – 99999
Postcode 32000 – 37999
Postcode 40000 – 79999
Sales Austria
Kurt Stritzelberger
Pewatron AG
Neumarkter Straße 86a
D-81673 Munich
Gerhard Vetter
Pewatron AG
Fürstenbergstraße 12
D-55422 Bacharach-Medenscheid
Kurt Stritzelberger
Pewatron AG
Neumarkter Straße 86a
D-81673 Munich
Phone + 49 89 260 52 80
Mobile + 49 171 803 41 35
Phone + 49 674 394 75 75
Mobile + 49 163 762 74 30
Phone + 49 89 260 52 80
Mobile + 49 171 803 41 35
[email protected]
[email protected]
[email protected]
Pressure Sensors
Gas sensors / Gas sensor modules
Load cells
Linear position sensors
Angle sensors
Philipp Kistler
Phone + 41 44 877 35 03
[email protected]
Thomas Clausen
Phone + 41 44 877 35 13
[email protected]
Eric Letsch
Phone + 41 44 877 35 14
[email protected]
Accelerometers
Power supplies
Current sensors
Eric Letsch
Phone + 41 44 877 35 14
[email protected]
Sebastiano Leggio
Phone + 41 44 877 35 06
[email protected]
Sebastiano Leggio
Phone + 41 44 877 35 06
[email protected]
Drive technology
CH Postcode 5000 – 9999 / DE
Drive technology
CH Postcode 1000 – 4999 / AT / IT / FR
Roman Homa
Mobile + 41 79 444 00 86
[email protected]
Christian Mohrenstecher
Mobile +41 76 444 57 93
[email protected]
Sales Other Countries / Product Management
Competitive sensor & power supply solutions worldwide
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement