TruCheck - Norbar Torque Tools

TruCheck - Norbar Torque Tools
TAKE
NORBAR
TakePRIDE
Pride –– TORQUE
Torque Norbar
NORBAR TORQUE TOOLS LTD
Beaumont Road, Banbury, Oxfordshire, OX16 1XJ
UNITED KINGDOM
Tel + 44 (0)1295 753600
Email enquiry[email protected]
TruCheck™
Technical Specification
Accuracy: +/-1%, +/-1 digit over the stated operating range.
Display: 4 digit, 7 segment LED
TruCheck 350 N.m and 250 lbf.ft
Dimensions in mm: 145.5(d) x 150(w) x 85(h)
Weight: 3.2 kg shipping
TruCheck 1000 N.m and 750 lbf.ft
Dimensions in mm: 145.5(d) x 175(w) x 85(h)
Weight: 4.8 kg shipping
Materials/Finish: Self coloured rigid polypropylene case.
Stainless steel transducer shaft and zinc plated steel base plate.
Calibration Options
TruCheck instruments are supplied as standard with a
traceable calibration certificate for the clockwise direction.
As an option, UKAS accredited calibration certificates from
Norbar’s laboratory can be supplied, either clockwise only or
clockwise and counter clockwise.
DESCRIPTION
PART NO.
UKAS accredited calibration clockwise
TCACC.CW
UKAS accredited calibration clockwise and counter clockwise
Distributed by
TCACC.CW+CCW
Note: UKAS accredited calibration is from 5% to 100% of full scale
for TruCheck 350 N.m and 250 lbf.ft (part numbers 43221, 43226
and 43222) and 10% to 100% for TruCheck 1000 N.m and 750 lbf.ft
(part numbers 43230, 43231 and 43237).
www.norbar.com
Part No. 07430 Issue December 08
TruCheck™
TruCheck™
TruCheck™ Plus
Simple, Cost Effective Torque
Wrench Testing
Simplicity
Flexibility
The importance of keeping your torque tools in peak calibration
condition is well established. Many businesses achieve this by using a
third party calibration service. However, how much more convenient
would it be to perform calibration checks in-house? Wrenches could
be checked more frequently, immediately if a problem is suspected,
and wrenches would not need to leave site unnecessarily.
One of the concerns in putting a torque tester into an environment
where people are not calibration specialists is that incorrect
selections will be made with the potential for incorrect tool setting
and consequently tool failure.
Accepting that some customers require more flexibility than the
basic TruCheck provides, the ‘Plus’ adds a comprehensive range
of features. With three modes of operation the TruCheck Plus
is suitable for click wrenches, dial and electronic wrenches and in
‘Track’ mode will continually monitor the torque signal.
There are three torque units: N.m, lbf.ft and lbf.in.
The main reasons that more companies do not perform
calibration checks on their own wrenches are the cost of
testers and fears over the complexity of the testing equipment.
Norbar’s ‘TruCheck’ torque wrench testers aim to sweep aside
these concerns. They are very cost effective being significantly
cheaper than most similar products on the market and the basic
version of the TruCheck is particularly simple to use.
TruCheck Plus also has a user selectable ‘limit’ feature.
The operator sets the target torque and tolerance and the
instrument will calculate whether the reading is within tolerance
and indicate the result by illuminating one of three coloured
LEDs: yellow = low, green = OK, red = high.
Finally, TruCheck Plus has an RS-232 serial data output and comes
complete with an RS-232 lead. The reading, measurement unit
and limit status (Low, OK or High) are output via RS-232.
The product comes in two versions: there is a basic version,
simply called ‘TruCheck’ and a version with greater functionality
called ‘TruCheck Plus’.
TruCheck Plus 100 - 1000 N.m.
TruCheck 10 - 350 N.m
¾” socket is supplied
Norbar’s solution is to remove all choices from the operator.
The TruCheck is for click type torque wrenches and comes with
a single measurement unit (N.m or lbf.ft). There is only one
button on the device and that is to zero the display. Operation
is simplicity itself – it is virtually impossible to go wrong!
TruCheck
MODEL
PART NO.
RANGE
TruCheck 350 N.m
43221
10-350 N.m
TruCheck 250 lbf.ft
43226
10-250 lbf.ft
TruCheck 1000 N.m
43230
100-1000 N.m
TruCheck 750 lbf.ft
43237
75-750 lbf.ft
TruCheck Plus
MODEL
PART NO.
RANGE
TruCheck Plus 350 N.m
43222
10-350 N.m
TruCheck Plus 1000 N.m
43231
100-1000 N.m
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement