January 2017 | FaCTOry PriCing wiTh PrOduCT

January 2017 | FaCTOry PriCing wiTh PrOduCT
J a n u a ry 2 0 1 7 |
-7
FAC TO RY P r i c i n g w i t h P ro d u ct S p e c i f i c at i o n s
Millenium Consoles | 2-9
Clocks and Timing Systems | 10-11
Analog & Digital Distribution Amplifiers | 12-13
Telephone Hybrid | 14
StudioHub+ Adapters and Cables | 15-17
StudioHub+ MatchJacks | 18
StudioHub+ Active and Passive Panels | 19-20
StudioHub+ Power Supplies | 21
StudioHub+ Hubs | 22-23
StudioHub+ Product Packages | 24-25
StudioHub+ Mounts | 26
2
millenium HYBRID consoles
Millenium Hybrid Console (Model RS-18HRJ shown)
Features:
• Full metering with programmable LED
peak indicators
• 8 position switcher for external devices
• 3 output buses from every channel
• Complete monitoring section
• Cue logic is user programmable to function in several modes
• Channel on/off keypad switches are LED illuminated
• Easiest to wire and service in the industry
• Available w/ StudioHub+ or barrier strip
I/O connectivity
Our “Hybrid Analog&Digital” Consoles offer the best of both worlds with dependable
analog circuitry plus dual digital outputs for Program and Audition buses and highresolution LED metering.
Famous StudioHub+ connectivity on all inputs and outputs ensure fast plug-and-play
installation. Removable barrier strip I/O connectors are also available.
Radio Systems’ Millenium Hybrid Broadcast Consoles are a superb value. Thousands
of RS Series Consoles have been sold since they were introduced 15 years ago, and
today the Millenium Series carries on this tradition with enhanced capabilities and
dramatic new styling. Take a hard look at Millenium broadcast consoles. They offer a
dazzling combination of superb specifications, sleek modern styling and a wide range
of features—all at unexpectedly low prices!
HYBRID SPECIFICATIONS
Models Available
RS-6H5P: 6 channel
RS-6HRJ: 6 channel
RS-12H5P: 12 channel
RS-12HRJ: 12 channel
RS-18H5P: 18 channel
RS-18HRJ: 18 channel
Analog Audio Inputs
Type: differentially balanced instrumentation amplifiers with
gain set jumpers and selectable input attenuators
Level: jumper selectable gain settings to accommodate
nominal input levels from -60 dBm to +10 dBm.
Maximum input level: +22 dBm
Impedance: 20K ohms or jumper selected
Headroom: 22 dBm at any level
Analog Line Outputs
Type: actively balanced
Level: adjustable 0 dBm to +10 dBm,
maximum output +22 dBm
Impedance: 100 ohms
Distortion: .008% at nominal operating level, 20 Hz to
20 kHz, Pgm, Aud and Mono outputs signal to noise: 88
dB (or better) below +4 dBm with 0 dBv input level, 20 kHz
bandwidth, 600 ohm source impedance (line to line) 74 dB
(or better) below +4 dBm output with -50 dBv input level, 20
kHz bandwidth, 150 ohm source impedance (mic to line)
Digital Line Outputs
Signal Format: AES-3
Signal Compliance: 24 bit
Output Sample Rate: 48 kHz/44.1 kHz /32 kHz-Crystal Selected
Digital Reference: Crystal (internal)
Conversions: A/D 24-bit, Delta-Sigma,
256x oversampling
RJ-45 “StudioHub+” Connectors
Monitor Sends
Level: 1 volt rms nominal, 10 volts rms maximum,
balanced RJ-45 “StudioHub+” Connectors
Headphone Output
Level: 1 volt rms nominal, 10 volts rms maximum into 600 ohm
headphone
Distortion: .05% typical, .1% maximum
Impedance: 50 ohms to front panel jack, 330 ohms to prefader
(external amp) output
Cue Output
2 watts rms into 8 ohm speaker
RJ-45 “StudioHub+” Connectors
Available Accessories
Copy stand
StudioHub+ Harness
Source cables - specify type
Spare power supply
Auxiliary relay
Available Options
Selector logic card
Enhanced remote interface card
Intercom Card
Four source switcher card
DA Mixer
Four output mix-minus boards
IFB switcher
Colored fader knobs
Warranty
2 years parts and service
Specifications subject to change without notice
Dimensions
All consoles are 27 inches deep and 9 inches tall
6 channel: 20.75 inches long
12 channel: 32.75 inches long
18 channel: 44.75 inches long
Frequency Response: +/- .2 dB 20 Hz to 20 kHz
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
3
millenium HYBRID consoles
Factory
Part #
Description
Price HYBRID Consoles
RS-6H5P
RS-6HRJ
RS-12H5P RS-12HRJ RS-18H5P RS-18HRJ 6 Channel Analog & Digital Console with 5-pin barrier strip I/O connectors 6 Channel Analog & Digital Console with RJ-45 I/O connectors 12 Channel Analog & Digital Console with 5-pin barrier strip I/O connectors 12 Channel Analog & Digital Console with RJ-45 I/O connectors 18 Channel Analog & Digital Console with 5-pin barrier strip I/O connectors 18 Channel Analog & Digital Console with RJ-45 I/O connectors 5,495.00
5,495.00
7,495.00
7,495.00
9,495.00
9,495.00
HYBRID CONSOLE ACCESSORIES
SH-CONSOLE-KITSM COPY-6
For RS-6HRJ 6 Channel Hybrid Console
Small Console Kit Copy Stand
325.00
395.00
SH-CONSOLE-KITMD
COPY-12
For RS-12HRJ 12 Channel Hybrid Console
Medium Console Kit
Copy Stand
475.00
445.00
SH-CONSOLE-KITLG
COPY-18
For RS-18HRJ 18 Channel Hybrid Console
Large Console Kit
Copy Stand
625.00
495.00
PS-CONSOLE
PS-CONSOLEHS
For All Consoles
Power Supply for all Consoles
Redundant Power Supply for all Consoles
1,295.00
1,295.00
HYBRID system options
LOGIC
REMOTE
ROUTER
INTERCOM
SPEAKER
DUAL-A/D
FOURMIX-KIT
SIXMIX-IN
DA-RJ
DA-MIXER
DUAL-IFB
DA-RJ
P&G
4PDT
SPDT Selector Logic Card - Adds logic to front panel selector
Enhanced Interface Card - On/Off relay closure & opto-isolated input control with barrier strip connectivity
Four Source Switcher Card - 1 x 4 stereo router with barrier strip connectivity
Intercom Kit - supports up to 4 stations with barrier strip connectivity
Intercom Speaker - 2-way speaker with call button with barrier strip connectivity
Dual channel A to D converter with RJ-45/StudioHub+ connectivity
Four Output Mix-Minus Kit - 4 mix-minuses from 6 input channels
Six Input Mix-Minus Board - Adds 6 additional channels to the above
4 output stereo DA with RJ-45/StudioHub+ connectivity
4 inputs to any of 8 outputs with barrier strip connectivity Interrupts four mono or two stereo sends with RJ-45/StudioHub+ connectivity
4 Output Stereo DA - Stereo output to up to four stereo sources with RJ-45/StudioHub+ connectivity
Penny & Giles Fader Option with Cue detent (per channel)
Accessory Relay - Mechanical Type (4PDT) Accessory Relay - Electronic Type (SPDT) 225.00
150.00
225.00
350.00
150.00
575.00
1,000.00
750.00
195.00
225.00
350.00
195.00
195.00
50.00
50.00
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
4
Millenium Digital Consoles
Millenium Digital Console (Model RS-18D shown)
Features:
• Analog or Digital capable on every channel
• 32 bit resolution
• Sample rate conversion on every input
• 10 extra auxiliary output buses
• Up to 10 fully programmable
mix-minus outputs
• Serial RS-232 interface
• Sleek new front-panel styling
• PC connect bus routing software included
• Simultaneous analog or digital outputs
of every bus
The tradition of the Millenium Console continues with a complete digital
transformation. The Millenium Digital is now 100% AES/EBU capable on
every input and output. In addition, performance has been enhanced with
10 fully programmable mix-minus outputs and a serial interface to third party
equipment.
Millenium Digital Consoles are available in 6, 12 and 18 channel frame sizes,
appropriate for any-size application. All consoles offer identical channel
features, monitor stages and available option card complements. Optional
I/O connectors are available for all input and output circuit boards with easyto-wire 5-pin balanced removable screw terminal connectors or with StudioHub+ standard RJ-45 connectors.
Digital SPECIFICATIONS
Measurements are made with 600 ohm loads connected
to the analog outputs.
0 dBu equals 0.775 volts RMS independent of load
impedance, 0 dBm equals 0.775 volts into a 600 ohm load.
Reference Level: +4dBu equals -20 dBFS. FSD equals
Full Scale Digital equals +24 dBu
Analog Line Inputs
Input Impedance: 40 k ohms, instrumentation amplifier
balanced Input Level Range: jumper selectable nominal input
level of -16 dBu, -6dBu or +4 dBu
Input Level Trim: software trim (digital gain adjust) +/-12.5 dB.
Input Headroom: 20 dB above nominal input
Analog Monitor Inputs
Input Impedance: 10 k ohms minimum, differentially balanced
Input Level Range: Adjustable +4 dBu nominal, -10 dBu
minimum Input Headroom: 20 dB above nominal input
Microphone Preamplifiers
Input Impedance: 10 k ohms
Source Impedance: 150 ohms
Input Level Range: Selectable in 5 dB steps, -62 dBu to - 22dBu
Equivalent Input Noise: -128 dBu, 150 ohm source, 20 kHz
measurement bandwidth
Input Headroom: 20 dB above nominal input
Digital Inputs
Signal Format: AES-3, S/PDIF
Signal Compliance: 24 bit
Input Sample Rate: 32 kHz - 96 kHz, sample rate conversion is
provided for all digital inputs
Input Level: -20 dBFS nominal
Input Level Trim: software trim (digital gain adjust) +/-12.5 dB.
Input Headroom: 20 dB above nominal input
Digital Outputs
Signal Format: AES-3
Signal Compliance: 24 bit
Output Sample Rate: 48 kHz
Digital Reference: Crystal (internal) or external AES-3
input at 48 kHz 100 ppm
Internal Sample Rate: 48 kHz
Processing Resolution: 32 bit floating point DSP
Conversions: A/D 24-bit, Delta-Sigma, 256x oversampling; D/A
24-bit, Delta-Sigma, 256x oversampling
Latency: <1.0 ms, analog in to analog out
22 kHz measurement bandwidth, 112 dB “A” weighted Digital
Input to Digital Output: 123 dB referenced to FSD, 22 kHz
measurement bandwidth, 126 dB “A” weighted
Total Harmonic Distortion + Noise
Analog Input to Analog Output: <0.008%, 20 Hz to 20 kHz, +23
dBu input, +23 dBu output, 22 kHz measurement bandwidth
Analog Input to Digital Output: <0.004%, 20 Hz to 20 kHz, +23
dBu input, +23 dBu output, 22 kHz measurement bandwidth
Digital Input to Digital Output: <0.0005%, 20 Hz to 20 kHz, -1
dBFS input, -1 dBFS output, 22 kHz measurement bandwidth
Digital Input to Analog Output: <0.004%, 20 Hz to 20 kHz , -1
dBFS input, +23 dBu output, 22 kHz measurement bandwidth
Isolation
Program-to-Program or Program-to-Utility: >88 dB, 20 Hz to
20 kHz A Input to B Input, B Input to A Input, >100 dB
Stereo Separation
Analog Program Outputs: >88 dB, 20 Hz to 20 kHz
Frequency Response
Warranty
Line Input to Program or Utility Output: +0 dB/-0.5 dB,
20 Hz to 20 kHz
Microphone Input to Program or Utility Output: +0dB/-.5dB,
20 Hz to 20 kHz
Warranty is two years from date of receipt. All factory nonwarranty service is guaranteed for 90 days. For full warranty
information, refer to the product manual.
Technical assistance is available at all times at no charge by
telephone or written correspondence. Items to be returned for
repair must include a Return Authorization number obtained
from Radio Systems.
Analog Outputs
Dynamic Range
Output Source Impedance: Utility Buses <3 ohms balanced,
all others 90 ohms.
Output Load Impedance: 600 ohms minimum
Nominal Output Level: +4 dBu
Maximum Output Level: +24 dB
Analog Input to Analog Output: 106 dB referenced to FSD,
22 kHz measurement bandwidth, 109 dB “A” weighted Analog
Input to Digital Output: 109 dB referenced to FSD, 22 kHz
measurement bandwidth, 112 dB “A” weighted
Digital Input to Analog Output: 109 dB referenced to FSD,
*Specifications are subject to change without notice.
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
5
Millenium Digital Consoles
Factory
Part #
DescriptionPrice Digital Consoles
RS-6D5P
RS-6DRJ RS-12D5P RS-12DRJ
RS-18D5P RS-18DRJ
6 Channel Digital Console with 5 Pin I/O connectors
6 Channel Digital Console with RJ-45 I/O connectors 12 Channel Digital Console with 5 Pin I/O connectors 12 Channel Digital Console with RJ-45 I/O connectors 18 Channel Digital Console with 5 Pin I/O connectors
18 Channel Digital Console with RJ-45 I/O connectors 5,995.00
5,995.00
8,995.00
8,995.00
11,995.00
11,995.00
Digital Console ACCESSORIES
SH-CONSOLE-KITSM
COPY-6
For RS-6D 6 Channel Digital Console
Pre-wiring kit of StudiHub+ Patch Cables and Adapters
Copy Stand
325.00
395.00
For RS-12D 12 Channel Digital Console
Pre-wiring kit of StudiHub+ Patch Cables and Adapters
475.00
SH-CONSOLE-KITMD
COPY-12
Copy Stand
445.00
SH-CONSOLE-KITLG
COPY-18
For RS-18D 18 Channel Digital Console
Pre-wiring kit of StudiHub+ Patch Cables and Adapters
Copy Stand
PS-CONSOLE
PS-CONSOLEHS
For All Consoles
Power Supply for all Consoles
Redundant Power Supply for all Consoles
625.00
495.00
1,295.00
1,295.00
Digital system options
REMOTE
ROUTER
INTERCOM
SPEAKER
DUAL-A/D
DA-MIXER
DUAL-IFB
DA-RJ
P&G
4PDT
SPDT Enhanced Interface Card - On/Off relay closure &
opto-isolated input control with barrier strip connectivity
Four Source Switcher Card - 1 x 4 stereo router with barrier strip connectivity
Intercom Kit - supports up to 4 stations with barrier strip connectivity
Intercom Speaker - 2-way speaker with call button with barrier strip connectivity
Dual channel A to D converter with RJ-45/StudioHub+ connectivity
4 inputs to any of 8 outputs with barrier strip connectivity Interrupts four mono or two stereo sends with RJ-45/StudioHub+ connectivity
4 Output Stereo DA - Stereo output to up to four stereo sources
with RJ-45/StudioHub+ connectivity
Penny & Giles Fader Option with Cue detent (per channel)
Accessory Relay - Mechanical Type (4PDT) Accessory Relay - Electronic Type (SPDT) 150.00
225.00
350.00
150.00
575.00
225.00
350.00
195.00
195.00
50.00
50.00
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
6
millenium IP consoles
Millenium IP Console (Model RS-18DIP shown)
Features:
• Livewire® compatible
• Add Livewire® nodes and software
to expand to a full network system
• 6 or 12 channels of local audio input
with A/B switching
• Internal mix engine for stand alone
operation
• Internal Axia GPI for remote control
operation
• Select any Axia input on any LCD
above the 6 Axia faders
• 8 selectable preset “scenes” of
Axia configurations
Millenium consoles featuring Livewire® begin a tradition of shared standards and plugand-play compatibility for the broadcast industry. Radio Systems Livewire® consoles
offer both stand-alone functionality and Livewire IP-Audio network connectivity. And
because it’s a STANDARD - Millenium consoles now also communicate with any Axia
device or any Livewire-enabled product from a growing list of manufacturers.
Local channels feature two inputs each of stereo analog inputs with mic thru line-level
sensitivity. Digital inputs are AES/EBU or S/PDIF with sample rate conversion. Livewire
channels feature a rotary encoder and LCD two-line read-out for the display and
selection of any system-wide Livewire source. Outputs include two stereo and 10 fully
programmable mix-minus buses. All buses also create Livewire streams accessible
throughout the Livewire network.
With Millenium Livewire consoles you can input local studio audio AND share audio
between consoles or playback iPlay equipped digital delivery systems - with no
additional hardware! For remote analog or digital I/O add any number of Axia Livewire
nodes.
Finally, use any Windows® PC to run iPlay® or PathfinderPC® software for system
configuration or Windows Media local audio playback.*
*Qualified Ethernet Switch requred for larger system configurations
IP Specifications
(Local analog and digital input and output specifications are identical to
digital console specifications)
Digital Audio Inputs and Outputs
Reference Level: +4 dBu (-20 dB FSD)
Impedance: 110 Ohm, balanced (XLR)
Signal Format: AES-3 (AES/EBU)
AES-3 Input Compliance: 24-bit with selectable sample rate conversion,
32 kHz to 96kHz input sample rate capable.
AES-3 Output Compliance: 24-bit
Digital Reference: Internal (network timebase) or external
reference 48 kHz, +/- 2 ppm
Internal Sampling Rate: 48 kHz
Output Sample Rate: 44.1 kHz or 48 kHz
A/D Conversions: 24-bit, Delta-Sigma, 256x oversampling
D/A Conversions: 24-bit, Delta-Sigma, 256x oversampling
Latency <3 ms, mic in to monitor out, including network and processor loop
Livewire® is a registered trademark of TLS Corporation
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
7
millenium IP consoles
Factory
Part #
Description
Price Digital Consoles
RS-6IP
RS-12IP
RS-18IP
6 Channel Digital Console with 6 channels of IP audio
12 Channel Digital Console with 6 channels of IP audio
18 Channel Digital Console with 6 channels of IP audio
7,995.00
10,995.00
13,995.00
NETWORK Console ACCESSORIES
COPY-6
SH-CONSOLE-KITSM
For RS-6IP 6 Channel Network Console
Copy Stand
Pre-wiring kit of StudiHub+ Patch Cables and Adapters
COPY-12
SH-CONSOLE-KITMD
For RS-12IP 12 Channel Network Console
Copy Stand
445.00
Pre-wiring kit of StudiHub+ Patch Cables and Adapters
475.00
COPY-18
SH-CONSOLE-KITLG
For RS-18IP 18 Channel Network Console
Copy Stand
Pre-wiring kit of StudiHub+ Patch Cables and Adapters
PS-IP PS-IPHS For All IP Consoles
Power Supply for all Livewire Consoles
Redundant Livewire Console Power Supply
395.00
325.00
495.00
625.00
1,495.00
1,495.00
IP system options
REMOTE
ROUTER
INTERCOM
SPEAKER
P&G
4PDT
SPDT Enhanced Interface Card - On/Off relay closure &
opto-isolated input control with barrier strip connectivity
Four Source Switcher Card - 1 x 4 stereo router with barrier strip connectivity
Intercom Kit - supports up to 4 stations with barrier strip connectivity
Intercom Speaker - 2-way speaker with call button with barrier strip connectivity
Penny & Giles Fader Option with Cue detent (per channel)
Accessory Relay - Mechanical Type (4PDT) Accessory Relay - Electronic Type (SPDT) 150.00
225.00
350.00
150.00
195.00
50.00
50.00
For additional replacement parts, see preceding section for the Millenium Digital Console
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
8
Factory
Description
Part #
Price SPARE & REPLACEMENT CIRCUIT BOARDs
Analog 6 Channel Control Board
Compatible with Analog 5 Pin & StudioHub+ RJ-45 Consoles
18516
$800.00
18522
$850.00
Compatible with IP & StudioHub+ RJ-45 Consoles
15395
$995.00
Analog 6 Channel Audio Board for 5 Pin 16795
$995.00
Digital 6 Channel Control Board
Compatible with Digital 5 Pin & StudioHub+ RJ-45 Consoles
IP LCD 6 Channel Control Board
Compatible with Analog 5 Pin Consoles
Analog 6 Channel Audio Board for StudioHub+ RJ-45
16796$995.00
Compatible with StudioHub+ RJ-45 Consoles
Digital 6 Channel Mother Board for 5 Pin 14904
$800.00
14905
$800.00
16144
$1,595.00
Digital daughter plug-in Board for Digital Consoles
15304
$200.00
Analog daughter plug-in Board for Digital Consoles
15303
$200.00
Compatible with Digital 5 Pin Consoles
Digital 6 Channel Mother Board for StudioHub+ RJ-45 Compatible with Digital StudioHub+ RJ-45 Consoles
IP Livewire 6 Channel Mother Board for StudioHub+ RJ-45 Compatible with IP StudioHub+ RJ-45 Consoles
Analog Output Board for 5 Pin
14800B$995.00
Compatible with Analog & Digital 5 Pin Consoles
Analog Output Board for StudioHub+ RJ-45
15354B
$995.00
Compatible with Analog & Digital StudioHub+ RJ-45 Consoles
Digital Output Board for 5 Pin
16786$1,795.00
Compatible with Digital 5 Pin Consoles
Digital Output Board for StudioHub+ RJ-45
16787$1,795.00
Compatible with Digital StudioHub+ RJ-45 Consoles
Digital Monitor Board for Digital Consoles
15277
$500.00
Analog Monitor Board for Analog Consoles
10887
$500.00
14401B
$195.00
Console Clock/Timer for all Consoles
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
9
Factory
Description
Part #
Price SPARE CONSOLE PARTS
These parts are compatible with all consoles.
Fader Assembly
18262
$75.00
Rotary Pot Assembly for Monitor, Headphone or Cue
11025
$35.00
Headphone Jack Assembly
7548
$20.00
Bus Select Keypad
15272
$25.00
ON/OFF Select Keypad
15273
$50.00
Monitor Select Keypad
15274
$50.00
Fader Knob - Blue
18512
$6.00
Fader Knob - Grey
15408
$6.00
REPLACEMENT SEMICONDUCTOR KITS
Semiconductor Parts Kit for all Analog Consoles
Includes every console semiconductor
and spare fuses - (for thru-hole PCB Consoles)
11006
$250.00
Semiconductor Parts Kit for all Digital Consoles
Includes every console semiconductor
and spare fuses - (for thru-hole PCB Consoles) 15325
$300.00
Analog Discount Spare Parts Kit #1 for Analog 5 Pin Consoles
Includes 1 output board, 2 faders, semiconductor parts kit
11007
$1,295.00
Analog Discount Spare Parts Kit #2 for Analog 5 Pin Consoles
Includes 1 each of every circuit board,
2 faders and full semiconductor kit
11008 $3,500.00
Analog Discount Spare Parts Kit #1 for Analog RJ-45 Consoles
Includes 1 output board, 2 faders, semiconductor parts kit
16860
Analog Discount Spare Parts Kit #2 for Analog RJ-45 Consoles
Includes 1 each of every circuit board,
2 faders and full semiconductor kit
16861 $3,500.00
Digital Discount Spare Parts Kit #1 for Digital 5 Pin Consoles
Includes 1 output board, 2 faders, semiconductor parts kit
15326
$2,195.00
Digital Discount Spare Parts Kit #2 for Digital 5 Pin Consoles
Includes 1 each of every circuit board,
2 faders and full semiconductor kit
15327
$5,195.00
Digital Discount Spare Parts Kit #1 for Digital RJ-45 Consoles
Includes 1 output board, 2 faders,
semiconductor parts kit
10002 $3,500.00
Digital Discount Spare Parts Kit #2 for Digital RJ-45 Consoles
Includes 1 each of every circuit board,
2 faders and full semiconductor kit
18495
$1,295.00
$5,195.00
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
10
clocks & timing systems
CT-2002
Thin Display
CT-2002
Large 2” Display
CT-2002
Remote Control
CT-2002
Desktop .5” Display
CT-2002
Large 4” Display
GPS Antenna
CLOCKs & TIMING SPECIFICATIONS
Time Base
Thin, Desktop and 2 Inch and 4 Inch:
Crystal oscillator with frequency trim provided.
Power
90 -246 VAC +/- 10%, 60/50 Hz
(external “wall wart” supply included.
GPS Desktop and GPS 2 Inch will maintain time
of day for 10 hours during power interruption with
internal 9V battery (not included).
CT-DESK
RJ-45 Connection
Serial Time Code In
Serial Time Code Out
Terminal Strip
RJ-45 SHIELD TO GND
Serial Time Code In +
Serial Time Code In Ground
Serial Time Code Out Serial Time Code Out +
Ground
Start Switch
Stop Switch
Reset Switch
Mode Switch
Ground
Time Closure 1
Time Closure 2
Time Closure 3
Time Closure 4
Ground
Down Time Closure at “0”
Top-of-Hour Reset Input
Dimensions
Thin Displays - 7” Wide x 2.5” High x 1.25” Deep
Desktop Displays - 7” Wide x 2.5” High x 4.5” Deep
2” Displays - 15.125” Wide x 5.25” High x 3.00” Deep
4” Displays - 24.50” Wide x 7.00” Highx 3.00” Deep
Options
Rack Mounts
GPS Extender Cables (increases cable length
from antenna up to 250’)
Windows Computer Sync Software for GPS units.
Windows only.
Warranty
One year parts and service.
CT-DESKGPS
RJ-45 Connection
GPS Antenna
DIP Switches
Time Zone Offset
Terminal Strip
Serial Time Code Out +
Serial Time Code Out Ground
Start Switch
Stop Switch
Reset Switch
Mode Switch
Ground
1 Hz Out
Ahead
Back
DC to Clocks
10 Hz to Clocks
Ground
Common
Top-of-Hour Output - N.O. output
CT-2INCH & CT-4INCH (2 inch shown)
Serial Synchronizing Data
1- Serial Time Code In +
2- Serial Time Code In 3- Ground
4- Serial Time Code Out 5- Serial Time Code Out +
Remote Control
6- Ground
7- Start Switch
8- Stop Switch
9- Reset Switch
10- Mode Switch
Clock Triggers
11- Ground
12- Time Closure #1
13- Time Closure #2
14- Time Closure #3
15- Time Closure #4
Ancillary I/O
16- Ground
17- Down Time Closure at “0”
18- Top-of-Hour Input
19- Ground
20- +15V DC
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
11
clocks & timing systems
Thin Display
Features:
• Simultaneous clock/up-timer/down-timer
on all models
• All units function as a remote timer
slave display
• High Intensity .56”, 2.3” and
4” LED displays
• Thin, Desktop, Wall and Rack mount
models
• Reliable, RF-immune RS-422 serial
data interface
• GPS, SMPTE & OCXO
reference options
• Local & parallel remote control
• I/R remote control included with
Desktop, 2 Inch and 4 Inch models
for down timing and special
programming of slave models
Only 1 1/4” deep for surface mounting
Simultaneous clock/up timer. Receives, displays and sends Radio Systems CT- compatible serial
time mode. Time-of-Day clock functions independently or as a master when remote drive signal
is available. Timer displays may be set to display remote (master) timer or function independently. Top-of-hour reset input. IR remote (optional - must be ordered separately) provides access
to the following features: down timer, 12/24 clock select, RSI or SMPTE serial time code input,
time-of-day offset, four time-of-day comparisons with wired remote output, top-of-hour-reset
offset, remote timer display.
Desktop Display
1/2” high LED display in desktop cabinet
Simultaneous clock/up timer. Receives, displays and sends Radio Systems CT- compatible
serial time mode. Time-of-Day clock functions independently or as a master when remote
drive signal is available. Timer displays may be set to display remote (master) timer or function
independently. Top-of-hour reset input. IR remote (included) provides access to the following
features: down timer, 12/24 clock select, RSI or SMPTE serial time code input, time-of-day
offset, four time-of-day comparisons with wired remote output, top-of-hour-reset offset, remote
timer display.
2 and 4” Inch Large Displays
2” and 4” high LED display for wall or rack mounting (2” high unit only)
Simultaneous clock/up timer. Receives, displays and sends Radio Systems CT- compatible
serial time mode. Time-of-Day clock functions independently or as a master when remote
drive signal is available. Timer displays may be set to display remote (master) timer or function
independently. Top-of-hour reset input. IR remote (included) provides access to the following
features: down timer, 12/24 clock select, RSI or SMPTE serial time code input, time-of-day
offset, four time-of-day comparisons with wired remote output, top-of-hour-reset offset, remote
timer display.
GPS Synchronization Option
GPS Antenna in weatherproof mount available for desktop, 2” & 4” Displays
Factory
Part #
Description
Price
CT2002 CLOCKS and TIMERS
CT-THIN
CT-DESK
CT-DESKGPS
CT-2INCH
CT-2INCHGPS
CT-4INCH
CT-IR
CT-RACKMED
CT-RACKLG
CT-SYNC
GPS-SYNC
CT-RS485 CT-150CABLE
CT-250KIT
CT-2002 Thin
CT-2002 Desktop
CT-2002 Desktop w/GPS Antenna
CT-2002 Large 2”
CT-2002 Large w/GPS Antenna
CT-2002 Large 4”
I/R Remote
Thin/Desktop Rack Mount
Large 2” Rack Mount PC Computer Sync Kit - generate or read RS serial time code to or from a PC
GPS Computer Sync Kit - generate or read GPS time code to a PC
Active RS-232 to RSS-485 Converter reqired for longer than 150ft.
GPS antenna runs
150’ GPS Extender Cable
250’ GPS Extender Cable with CT-RS485 converters included
250.00
295.00
795.00
795.00
1,295.00
995.00
35.00
50.00
50.00
295.00
495.00
150.00
195.00
240.00
Clocks and Timer Models may be mixed to obtain dealer volume discounts
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
12
ANALOG Distribution amplifier
ADA 2x8SS
Features:
• Front panel stereo metering
• Built-in silence sensor
• Super-low noise and distortion
specifications
• StudioHub+ / RJ-45 connectors
• 110/220 volt - CE certified
• Front panel input selectors and
audio presence indicators
• Rear panel full remote control and
silence sense trip time and audio
threshold selection
Radio Systems’ ADA 2x8SS is the world’s most fully featured audio distribution amplifier.
Employ it for transparent audio distribution with super low noise and distortion specifications.
Unique feature include full metering, headphone amplifier and two input switching actived
by fully adjustable silence sense circuitry or rear panel remote control. This allows the ADA
2x8SS to act as an automatic studio switcher or fail safe air chain controller.
ADA 2x8SS Rear Panel
ANALOG Distribution AMPLIFIER SPECIFICATIONS
Channels
2 inputs (stereo) x 8 outputs (stereo)
Input Impedance
40K ohms, balanced and bridging
Output Channel Isolation (crosstalk)
-105 dB (full bandwidth)
I/O and Remote Control Connectors
Shielded RJ-45
(audio connectors to StudioHub+ standard)
Input Gain
0 to +36 dB (16 dB, 26 dB, 36 dB – jumper selectable)
Dynamic Range
123 dB
Output Impedance
60 ohms, balanced
Headroom
21 dB above +4 dBm output (into 600 ohm load)
Maximum Output Level
+25 dBm (into 600 ohm load)
Common Mode Rejection
-50 dB (full bandwidth)
Frequency Response: +0/-.1 dB 20 Hz to 20 kHz
Dimensions
19 inch (EIA rack mount) wide x 1.75 inches (1ru) high x
7.75 inches deep (with connectors)
Front Panel Metering
20 segment/stereo
Segments: -20 to -1 Green
Segments: 0 to -2 Yellow
Segments: +1 to PEAK Red
Front Panel Controls and Indicators
Audio Selected Indicator: A On / B On / Auto
Audio Presence Indicator: A On / B On / Tripped
Audio Select Control: Auto / Trip to B / Reset to A
Remote Control Pins
Control inputs: Auto / Reset / Test
Status outputs: Auto / Trip / Input A
DIP Switch Settings
Trip and Return Time: 2 to 256 seconds, selectable
Silent Sense Gain: -34dBu to -16dBu, selectable
Distortion: (thd + n): .002% 20 Hz to 20 kHz
(any output level into 600 ohm load)
Distortion: (SMPTE imd): .003%
(any output level into 600 ohm load)
Shipping Weight
8 pounds
Distortion: (dim) .002% (into 600 ohm load)
Noise: 102 dB below +4 dBm (full bandwidth
into 600 ohm load)
Factory
Part #
Description
Price
Distribution amplifiers
ADA-2x8SS
Model ADA 2x8SS - with StudioHub+ RJ-45 connectors
495.00
Analog and digital DA’s may be mixed to obtain dealer volume discounts
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
13
DIGITAL Distribution amplifiers
DDA 1x8SH
DDA 1x8SH Rear Panel
Features:
• Eight independent AES/EBU outputs
• Two front panel switched AES/EBU inputs
• RJ-45 connectors for AES/EBU inputs/
outputs
• Selectable 115/230 VAC, 50/60Hz
• Front panel AES/EBUinput presence
indicators
• Also available: DDA-1x4SH with four
AES/EBU outputs
Radio Systems’ DDA 1x8SH is our eight output AES/EBU non-reclocking digital distribution
amplifier. Front panel input switching allows one of AES/EBU inputs to be easily routed to the
eight independent outputs. Front panel indicators show which input is selected as well as
presence of AES/EBU input signals.
Also available as the DDA 1x4SH four output AES/EBU non-reclocking digital distribution
amplifier.
1 In x 8 Out Stereo AES EBUwith front panel 2 input switching
and rear panel RJ-45/StudioHub+ connectors
ANALOG Distribution AMPLIFIER SPECIFICATIONS
Overall
Frequency Response
+/- 0.1 dBfs, 20Hz – 20kHz
Distortion
.002% over 20Hz – 20kHz, output level
-20 dBfs (with 110 ohm load)
Noise
123 dB below 0 dBfs output level,
bandwidth
20 Hz -20kHz with 110 ohm input and
output termination
Inputs
1 Stereo AES/EBU
Nominal input -20 dBfs
Maximum input 0 dBfs
Dynamic Range 123 dB
Input Impedance 110 ohms
Rear panel jumper selectable grounding
options
Outputs
8 Stereo AES/EBU
Output Impedance 110 ohms
Maximum output 0 dBfs
LED Indicators audio (data) present
A/B input select
Physical
19” wide x 1.75” (1ru) high x 7” depth
48.3 wide x 4.4 (1ru) high x 17.8cm depth
Shipping
8lbs. / 3.6 Kgs.
23” x 13” x 3” / 58.5 x 33 x 7.7cm
Factory
Part #
Description
Price
Distribution amplifiers
DDA-1x8SH
DDA-1x4SH
MJ-DDA Model DDA 1x8 - with StudioHub+ RJ-45 connectors
Model DDA 1x4 - with StudioHub+ RJ-45 connectors
MatchJack Digital Distribution Amplifier
795.00
595.00
175.00
Analog and digital DA’s may be mixed to obtain dealer volume discounts
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
14
Telephone hybrid
DI-
Features:
• Dual line Hybrid functions as two
separate hybrids or conference system
• Full automated console remote control
• Automatic Digital Nulling
• Producer and screener phone support
• Auto-answer feature
• Console to-caller cueing
• Full line monitoring for auto call drop
and auto-nulling
• Internal mix-minus generation
• Acoustic room echo cancellation
• Record outputs
Radio Systems’ digital dual-line phone hybrid provides everything you demand from
a broadcast phone interface. Just a push of a dedicated front panel button answers
calls, puts callers on hold, on-the-air, or in conference mode. Digital line nulling
provides excellent separation and audio qualtiy, and microprocessor controlled
switching circuitry makes the DI-2000 the most featured, best sounding, and easiest
to use hybrid you’ll ever own. The DI-2000 is ideal for conference calls, with several
optional and programmable modes for mixing caller outputs and cue input buses.
The unit also creates an internal inter-caller talk path, eliminating the need to supply
a second mix-minus output from the console. The DI-2000 can also be programmed
to operate as two separate single-line units.
Specifications:
General
Telco Line Inputs
Audio Inputs
Impedance:10K ohm, active balanced
Maximum Input Level: +21 dBm
Nominal Input Level: +4 dBm
Connectors: 1/4” TRS balanced phone connectors
Mix-Minus Input: provides audio to caller
- 2 tip/ring standard (POTS) line inputs
- ring voltage detect
- off-hook line detect (for aux phone)
- line drop detect (for auto disconnect)
- RJ-11 (4-wire) connector
when on air
Cue Input: provides audio to caller when in answer/cue
Music on Hold Input: provides audio to caller when on hold
Audio Outputs
Impedance: 60 ohms, active balanced
Maximum Output Level: +14 dBm
Nominal Output Level: +4 dBm
Connectors: 1/4” TRS balanced phone connectors
Record Output: mix of caller and host audio
Cue Output: caller audio when in answer/cue
Speaker Level: cue channel
Main Output: caller audio when on air
Distortion
1% THD at 1 kHz
Frequency Response
300-3300 Hz +/- 1 dB
Noise
65 dB referenced to 0 dBm phone level
Remote Control Lines
Answer / cue switch control
Hold switch control
Air switch control
Drop switch control
Answer / cue lamp
Hold switch lamp
Air switch lamp
Line 1 & 2 seize relay (C form)
Transhybrid Loss
40 dB minimum
Power
115/230 V, 50/60 Hz, switchable
Warranty
1 year parts and service
Specifications subject to change without notice
Console Logic Remote Lines
Off switch control (answer, cue, hold, drop)
On switch control (air, cue)
Off lamp (ring flash, hold flash)
Factory
Part #
Description
Price
DI-2000 Dual Line Hybrid
$1,295.00
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
15
STUDIOHUB+ ADAPTERS
Description
Part #
Factory
Price
8” FEMALE ADAPTERS - FEMALE RJ-45 to XLR/TRS/RCA
1
2
ADAPT-XLRF
1. RJ-45 Female to XLR Female - 8”- Balanced
ADAPT-XLRF
20.00
2. RJ-45 Female to XLR Male - 8”- Balanced
ADAPT-XLRM
20.00
3. RJ-45 Female to 1/4” TRS Male - 8”- Balanced
ADAPT-TRSM
20.00
4. RJ-45 Female to RCA Male - 8”- Unbalanced
ADAPT-RCAM
20.00
5. RJ-45 Female to one 1/8” Male - 8”- Unbalanced
ADAPT-MINIM
20.00
ADAPT-XLRM
3
ADAPT-TRSM
4
ADAPT-RCAM 6. RJ-45 Female to two 1/8” Male - 8”- Balanced
ADAPT-MINIMBAL 20.00
5
7. RJ-45 Female to TA3 XLR Female - 8”- Balanced
(Mini XLR for NPR Content Depot)
ADAPT-TA3
20.00
8. RJ-45 Female to one 1/8” Female - 8”- Unbalanced
ADAPT-MINIMBAL
ADAPT-MINIF
20.00
9. RJ-45 Female to Bare End - 8”
ADAPT-TAIL
16.00
ADAPT-MINIM
6
7
ADAPT-TA3
8
ADAPT-MINIF
9
Note: Use these female adapters in combination with any length of RJ-45 to RJ-45 patch cables
to create connector/cable combination of any length.
ADAPT-TAIL
6 ft. MALE CABLES - MALE RJ-45 to XLR/TRS/RCA
1. RJ-45 Male to XLR Female - 6ft.- Balanced
CABLE-XLRF
25.00
2. RJ-45 Male to XLR Male - 6ft.- Balanced
CABLE-XLRM
25.00
3. RJ-45 Male to 1/4” TRS Male - 6ft. - Balanced
CABLE-TRSM
25.00
4. RJ-45 Male to RCA Male - 6ft. - Unbalanced
CABLE-RCAM
25.00
5. RJ-45 Male to one 1/8” Male - 6ft. - Unbalanced
CABLE-MINIM
25.00
1
2
CABLE-XLRF
CABLE-XLRM
3
4
CABLE-TRSM
6. RJ-45 Male to two 1/8” Male - 6ft. - Balanced
CABLE-MINIMBAL25.00
CABLE-RCAM
5
7. RJ-45 Male to one 1/8” Female - 6ft. - Unbalanced
CABLE-MINIM
7
CABLE-MINIF
6
8. RJ-45 Male to Bare End - 6ft.
CABLE-MINIF
25.00
CABLE-TAIL
20.00
CABLE-MINIMBAL
8
CABLE-TAIL
Note: Use these 6ft. male cables as stand-alone connector/cable combinations.
These RJ-45 Male 6ft. cables are designed for use with Axia Nodes, Wheatstone Blades,
and Logitek JetStream audio engines.
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
16
STUDIOHUB+ BREAK-OUT
Factory
Description
Part #
Price
DONGLES
RJ-45 to “D” connector adapters. Available for all major manufacturers’ analog and digital products that utilize “D” I/O connectors
Single
Dual
Quad
Single RJ-45 Dongle
Call
25.00
Dual RJ-45 Dongle
Call
35.00
Quad RJ-45 Dongle
Call
45.00
Dual “D” to Quad RJ-45 Dongle
Call
55.00
Dual “D” to Dual Quad RJ-45 Dongle
Call
65.00
Note: For a list of available dongles with pin-out configurations see:
http://www.studiohub.com/donglelist.html
Splitters, Attenuators AND COUPLERS
ATTEN-10DB
Stereo to mono summing pad, 6dB attentuation
ADAPT-SUM
35.00
Stereo “T” Splitter Adapter (8 wire for DC Power)
ADAPT-PWR
25.00
Left/Right “T” Splitter Adapter
ADAPT-L/R
25.00
Left/Left “T” Splitter Adapter
ADAPT-L/L
25.00
ADAPT-ATTEN10
ADAPT-ATTEN15
ADAPT-ATTEN20
ADAPT-ATTEN40
ADAPT-ATTEN50
35.00
35.00
35.00
35.00
35.00
ADAPT-MONO
20.00
ADAPT-COUPLER
6.00
ADAPT-PWR In Line Attenuator (10dB attenuation)
In Line Attenuator (15dB attenuation)
In Line Attenuator (20dB attenuation)
ADAPT-MONO
In Line Attenuator (40dB attenuation)
In Line Attenuator (50dB attenuation)
In Line Mono Adapter - Parallels left channel to left/right outputs
RJ-45 Coupler
RJ-45 to RJ-45 Shielded Coupler
(female to female - all eight wires)
BREAK-OUT
RJ-45 MALE to bare end (10ft. length) Made with CAT-5 cable for punch block use.
ADAPT-PUNCH
12.00
ADAPT-BO
35.00
DUAL RJ-45 Breakout Adapter to Push Terminals
Designed GPI Breakout of 2 GPI ports
ADAPT-GPI
45.00
RS 5 Pin Console Adapter for Millenium Consoles
ADAPT-RS
15.00
Broadcast Tools Lower Row Adapter
ADAPT-BTL
25.00
Broadcast Tools Upper Row Adapter
ADAPT-BTU
25.00
ADAPT-HENRY
25.00
RJ-45 Breakout Adapter to Screw Terminals
Designed to loop through patch cables for screw
ADAPT-BO terminal acces to all eight CAT-5 leads.
ADAPT-GPI
ADAPT-RS
ADAPT-BTL
ADAPT-PUNCH
Henry Engineering Adapter
ADAPT-HENRY Kramer Electronics Adapter
Axia DB15 Connector to two RJ-45’s
ADAPT-AXIA
Remote Control Adapters for various source gear
ADAPT-KRAMER 25.00
ADAPT-AXIA
25.00
Call
25.00
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: sale[email protected]
17
STUDIOHUB+ CAT-5 PATCH CABLES
Various lengths of shielded RJ-45 patch cords and cable for all StudioHub+ applications. 1 to 25 ft. lengths sold only in packages of ten.
Longer lengths sold individually. All StudioHub+ cabling is shielded and CAT-5 certified.
CAT-5 CABLES
Factory
Part #
Price
Patch
Cables Sold in Ten Packs
RJ-45 Patch Cables - 1’ (priced and shipped as 10 cables)
SH-PATCH1PK
25.00
RJ-45 Patch Cables - 2’ (priced and shipped as 10 cables)
SH-PATCH2PK
28.00
RJ-45 Patch Cables - 3’ (priced and shipped as 10 cables)
SH-PATCH3PK
32.00
RJ-45 Patch Cables - 5’ (priced and shipped as 10 cables)
SH-PATCH5PK
40.00
RJ-45 Patch Cables - 7’ (priced and shipped as 10 cables)
SH-PATCH7PK
45.00
RJ-45 Patch Cables - 10’ (priced and shipped as 10 cables)
SH-PATCH10PK
60.00
RJ-45 Patch Cables - 12’ (priced and shipped as 10 cables)
SH-PATCH12PK
75.00
RJ-45 Patch Cables - 15’ (priced and shipped as 10 cables)
SH-PATCH15PK
75.00
RJ-45 Patch Cables - 20’ (priced and shipped as 10 cables)
SH-PATCH20PK 100.00
RJ-45 Patch Cables - 25’ (priced and shipped as 10 cables)
SH-PATCH25PK 110.00
Patch Cables Sold Singly
RJ-45 Patch Cable - 35’ (priced and shipped as single cable)
SH-PATCH35
13.00
RJ-45 Patch Cable - 50’ (priced and shipped as single cable)
SH-PATCH50
20.00
RJ-45 Patch Cable - 75’ (priced and shipped as single cable)
SH-PATCH75
20.00
RJ-45 Patch Cable - 100’ (priced and shipped as single cable)
SH-PATCH100
30.00
RJ-45 Patch Cable - 125’ (priced and shipped as single cable)
SH-PATCH125
40.00
RJ-45 Patch Cable - 150’ (priced and shipped as single cable)
SH-PATCH150
45.00
CAT-5 SHIELDED PATCH CORDS
CAT-5 25 Pair Tie Line cable with RJ-21X connectors on both ends Factory Price
RJ-21 Cable - Specify length
RJ21TIE-xxx
$1.45 per ft. plus $80.00 for two ends
CAT-3 25 Pair Remote Control cable with RJ-21X connectors on both ends
F
actory Price
RJ-21 Cable - Specify length
RJ21RC-xxx
$1.25 per ft. plus $25.00 for two ends
BULK CABLE
BULK CAT-5 CABLES
CAT-5 25 Pair Unshielded 500’ Roll
CAT5-25-500
CALL
CAT-5 4 Pair Shielded Solid Wire 1000’ Roll
Grey
CAT5-1000GYCALL
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
18
STUDIOHUB+ MATCHJACKS
Factory
Description
Part #
Price
MatchJacks connect RJ-45 patch cables to various source equipment.
1. Pre-Amplifier-Output
(RCA consumer output to balanced line input) 1
MJ-OUT95.00
MJ-OUT
2. Pre-Amplifier-Input
(balanced line level output to consumer RCA input)
2
MJ-IN95.00
MJ-IN
3. S/PDIF to AES/EBU Converter
3
MJ-SPDIFOUT
95.00
MJ-SPDIFIN 95.00
MJ-SPDIFOUT
4. AES/EBU to S/PDIF Converter (passive)
4
MJ-SPDIFIN
5. A to D AES/EBU Converter
(includes PS-WWUCUBE 12 volt wall adapter power supply)
MJ-AD145.00
6. D to A AES/EBU Converter (includes PS-WWUCUBE 12 volt wall adapter power supply)
MJ-DA 145.00
MJ-DDA 175.00
SH-AESSPLIT
75.00
SH-GPIOLOGIC
125.00
5
MJ-AD
6
MJ-DA
7. AES/EBU Distribution Amp
(4 Output, includes 9 volt wall adapter power supply)
7
MJ-DDA
8
8. AES/EBU 2-Way Splitter Transformer (passive) splitter to provide
2 AES/EBU outputs from one input.
SH-AESSPLIT
8
SH-GPIOLOGIC
9. 3 Signal Logic Inverter
Inverts up to 3 logic inputs (signals which go high are inverted to
go low & signals which go low are inverted to go high).
Part numbers in red require DC power. See power supply options.
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
19
STUDIOHUB+ ACTIVE panels
Factory
DescriptionPart #Price
PANELS
Headphone Amp Stereo 1/2 Watt Amp SH-HPB
SH-MIC
SH-HPB
125.00
Headphone Amp Stereo with No Volume Control SH-HPBNV
110.00
Dual Headphone Amp Stereo 1/2 Watt Amp SH-HPDUAL
175.00
Mic Pre-Amp Mono female XLR connector
with Push to Talk
with Push to Talk plus full logic
SH-MIC
SH-MICPTT
SH-MICPTTPLUS
125.00
145.00
195.00
RCA and mini balanced RJ-45 inputs & outputs SH-MATCHPANEL
175.00
3 Mixer Plate Stereo 3 channel mixer with mix-minus
SH-MIXER
325.00
Monitor Level Panel In-line level control
SH-LEVEL
175.00
SH-VU
175.00
SH-SPKR
75.00
SH-AMPSPKR
175.00
SH-AMP
145.00
SH-AMPPHN
175.00
SH-SW4SS
175.00
SH-SW4POS
SH-SW8POS
SH-SW12POS
SH-SW16POS
295.00
470.00
645.00
820.00
SH-TALENT
300.00
SH-TALENTRJ
315.00
SH-HP and SH-1XLRF with SH-SURF2 Mount
SH-GUEST
200.00
SH-HP and SH-1XLRF with SH-SURF2 Mount
SH-GUEST
200.00
SH-WORLDPNL
380.00
Dual VU Meter Panel (Specify Vertical or Horizontal)
SH-MIXER
Speaker Panel with one miniature 8ohm speaker
Monitor Amp Panel 8 watt monitor amp w/Speaker
SH-PTTPLUS
Monitor Amp Panel 8 watt monitor amp w/o Speaker
Monitor Amp Panel 8 watt monitor amp w/Headphone
4 Source Switch Panel 4 Stereo sources to
1 stereo output
SH-VU
SH-SW4SS
4-16 Position Switchers in a 1 RU mount
4, 8, 12, & 16 input models
SH-HP, SH-1XLRF and SH-3BUT
with SH-SURF3 Mount
SH-HP, SH-1XLRF and SH-3BUT
with SH-SURF3 Mount with RJ-45 in/out
4-16 Position Switchers
World Panel - A factory preassembled panel consisting of:
SH-RACK4 / SH-2XLRF / SH-2XLRM / SH-1/4UNBAL / SH-MATCHPANEL
SH-WWU +/-15VDC Power Supply with 1 connector
SH-TALENT
SH-GUEST
Part numbers in red require DC power. See power supply options.
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
20
STUDIOHUB+ PASSIVE panels
Factory
Description
Part #
Price
PANELS
Active and passive panels that mount separately or as assemblies.
SH-1XLRF
SH-2XLRF
Single XLR Female Panel One female XLR connector
SH-1XLRF
35.00
Single 5 PIN XLR Female Panel One female XLR connector made specifically for MICA mic booms
to light LED
SH-1XLR5
55.00
Dual XLR Female Adapter Mono/Stereo Panel SH-2XLRF
45.00
Single XLR Male Panel One male XLR connector
SH-1XLRM
35.00
Dual XLR Male Adapter Mono/Stereo Panel SH-2XLRM
45.00
Dual XLR Male-Female Panel SH-2XLRMF
45.00
TRS 1/4” & Mini Panel Unbalanced in stereo
SH-1/4UNBAL
55.00
TRS 1/4” & Mini Panel Balanced dual mono
SH-1/4BAL
55.00
1 Push-Button Panel - with solder terminals and 12V LEDs
1 Push-Button Panel - with solder terminals and 5V LEDs
SH-1BUT
SH-1BUT5V
50.00
50.00
SH-1BUTRJ
SH-1BUTRJ5V
65.00
65.00
SH-2BUT
SH-2BUT5V
75.00
75.00
SH-2BUTRJ
SH-2BUTRJ5V
90.00
90.00
SH-3BUT
SH-3BUT5V
95.00
95.00
SH-3BUTRJ
SH-3BUTRJ5V
110.00
110.00
SH-1XLRF5
SH-1XLRM
1 Push-Button Panel - with RJ-45 connector* and 12V LEDs
1 Push-Button Panel - with RJ-45 connector* and 5V LEDs
SH-2XLRM
2 Push-Button Panel - with solder terminals and 12V LEDs
2 Push-Button Panel - with solder terminals and 5V LEDs
SH-1BUT
2 Push-Button Panel - with RJ-45 connector* and 12V LEDs
2 Push-Button Panel - with RJ-45 connector* and 5V LEDs
3 Push-Button Panel - with solder terminals and 12V LEDs
3 Push-Button Panel - with solder terminals and 5V LEDs
SH-3BUT
3 Push-Button Panel - with RJ-45 connector* and 12V LEDs
3 Push-Button Panel - with RJ-45 connector* and 5V LEDs
SH-2BUT
*”BUTRJ” push button panels terminate in RJ-45 connectors and integrate directly
with RS Millenium A and Millenium D remote control products.
SH-1/4BAL
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
21
STUDIOHUB+ POWER SUPPLIES
Factory
Description
Part #
Price
POWER SUPPLIES
Power Supplies to provide “DC-Link” power distribution to Hubs and active Panels and MatchJacks.
StudioHub+ External Power Supply
+/- 15 v DC regulated 4 Amps: wall mountable. Universal input voltage from 90-245VAC
Powers all StudioHub+ Hubs and Cubes
PS-EXTU
350.00
AC Wall Adapter Power Supply
Universal voltage from 90-250VAC. +/- 15 volts, 400 mA. Powers Active Plates, MatchJacks,
and PS Cube. US style power plug adapter supplied as standard.
PS-EXTU
Universal
4Amp External
Supply with 5 pin
MTA Connector
PS-WWBLACK
AC Wall Adapter
AC Wall Adapter with Black MTE Connector
Use with all current SH+ Panels, MatchJacks, Cubes and
AXIA powered Panels.
PS-WWBLACK25.00
AC Wall Adapter with White MTA Connector for use
with pre 2016 SH+ powered Panels and MatchJacks
PS-WWWHITE
25.00
Australian Power Plug Adapter
European Power Plug Adapter
United Kingdom Power Plug Adapter
PS-ADAPTAUS
PS-ADAPTEU
PS-ADAPTUK
2.50
2.50
2.50
with black MTE
PS-WWWHITE
Power Supply Cube Power Inserter
Adds “DC-link” to power up to four CAT-5 cables routed through the PS-CUBE.
Use a PS-EXTU for up to 4 amps or a PS-WWUCUBE for up to 400 mA.
Wall Adapter
with white MTA
Power Inserter Cube
Use a Console-Cable to power from Millenium Console - 6ft.
Use a Console-Cable to power from Millenium Console - 1ft.
Use PS-Cable to power from Millenium Console - 6ft.
PS-CUBE
16998
15884
16600
65.00
15.00
12.00
15.00
PS-AU
(Australia)
PS-EU
(Europe)
PS-UK
(United Kingdom)
Power Supply Combiner Board
PS-COMBINE
125.00
Diode combine 2 PS-EXTU supplies for redundant power. 2 DC inputs x 1 combined output.
LED status indicators. Mounts in lower half of standard hub chassis.
Current consumption for each StudioHub+ active device is charted below. Refer to this list when
calculating the total number of devices that can be run on any individual power supply.
SH+ items which require power supplies are noted in red.
PS-CUBE
4 Ch Power Inserter
PS-COMBINE
Part # MJ-OUT MJ-IN MJ-SPDIFOUT*
MJ-AD MJ-DA MJ-DDA **
SH-MATCHPANEL
SH-HP SH-MIC SH-MIXER 3 SH-AMPSPKR SH-LEVEL SH-VUV DA6-DC DA12-DC Description Analog MatchJack Out (IHF to Pro) Analog MatchJack In (Pro to IHF) MatchJack OUT (S/PDIF and Optical to AES) Digital MatchJack A to D Digital MatchJack D to A Digital MatchJack Distribution Amplifier Dual Match Panel Headphone Panel Mic Pre-Amp Panel Input Stereo Mixer with mix-minus Monitor Amp Panel (w/ Speaker) Monitor Panel Dual VU Meter Panel DA Hub (Single) DA Hub (Dual) *The MJ-SPDIFIN unit is passive and consumes no power
Current
75 mA
35 mA
100 mA
150 mA
150 mA
165 mA
100 mA
100 mA
55 mA
125 mA
1400 mA
145 mA
150 mA
575 mA
1150 mA
**Powered via 9VDC (single ended) wall adapter power supply
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
22
STUDIOHUB+ TIE LINE HUBS AND PATCH PANELS
Factory
Description
Part #
Price
MINILINES
TIE
TIE LINES
RJ-21 to 24 (x2) 4-Wire RJ-45’s w/110 Punch Connectors
24 Channels of RJ-45 4-wire tie lines. Each channel
has 2 RJ-45’s in parallel and a 110 punch connector.
Requires 2 CAT-5 25 pair RJ-21 connectorized cables.
TIE24-4
375.00
RJ-21 to 12 (x2) 4-Wire RJ-45’s w/110 Punch Connectors
Same as above - 1/2 Hub/single board/12 channel
version. Requires 1 CAT-5 25 pair RJ-21
connectorized cable.
TIE12-4
230.00
RJ-21 to 24 (x2) 4-Wire RJ-45’s w/DC-Link
Same as TIE24-4 w/o 110 Connectors;
adds DC-Link compatability.
TIE24-4DC
395.00
RJ-21 to 12 (x2) 4-Wire RJ-45’s w/DC-Link
Same as TIE12-4 w/o 110 Connectors;
adds DC-Link compatability.
TIE12-4DC
245.00
RJ-21 to 24 4-Wire RJ-45’s
24 Channels of RJ-45 4-wire tie lines on a 1 r.u.
rack plate or wall mount. Requires 2 CAT-5 25 pair
RJ-21 connectorized cables.
MINITIE24-4
245.00
RJ-21 to 12 4-Wire RJ-45’s
12 Channels of RJ-45 4-wire tie lines on a wallmount plate. Requires 1 CAT-5 25 pair RJ-21
connectorized cables.
MINITIE12-4
125.00
TIE24-4 TIE24-4DC MINITIE24-4
MINITIE12-4
PATCH PANELS
Model #A-1
Model #A-2
STUDIOHUB+ PATCH 48 STEREO ANALOG BOARD
JU8
SHIELD
JU7
SHIELD
JU6
SHIELD
JU5
SHIELD
JU4
SHIELD
STUDIOHUB+ PATCH 48 AES/EBU BOARD
JU3
SHIELD
JU2
SHIELD
JU1
SHIELD
JU8
SHIELD
STEREO ANALOG ADAPTER (1/3 WIDTH REAR PANEL ADAPTER)
JU7
SHIELD
JU6
SHIELD
JU5
SHIELD
Model
#A-2
Model
#A-1
Model
#A-3
ABC
STUDIOHUB+
PATCH
48 AES/EBU
BOARD
STUDIOHUB+
PATCH
48 STEREO
STUDIOHUB+
PATCH
48 I/OANALOG
BOARD BOARD
JU1
SHIELD
APTER)
JU1
1 SHIELD
SHIELD
PTER)
JU1
HIELD
SHIELD
JU7
JU8 JU8 JU7
JU7
JU8
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
ABC
JU4
JU3
JU4
JU3
JU4
JU3
SHIELD SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
JU1
JU2
JU1
JU2
JU1
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
ABC
Model
#A-3
Model
#A-4
Model
#A-1
Model
#A-2
Model
#A-5
ABC
ABC
ABC
ABC
STUDIOHUB+
PATCH
I/O BOARD
STUDIOHUB+
PATCH
4848
STEREO
ANALOG BOARD
STUDIOHUB+
PATCH
AES/EBU
BOARD
STUDIOHUB+
PATCH
4848RJ-21
BOARD
ABC
ABC
J1
JU8
JU7
JU6
JU5
JU4
JU3
JU2
JU1
JU8
JU7
JU6
JU5
JU4 JU3
JU3
JU2 JU1
JU1
JU4 SHIELD
JU2 SHIELD
JU8
BNC
75 OHM
BOARD
SHIELD JU7 SHIELD JU6 SHIELD JU5
SHIELD
SHIELD
SHIELD
SHIELDSHIELD
SHIELD SHIELDSHIELDSHIELD
SHIELD SHIELDSHIELDSHIELD
SHIELDSHIELD SHIELDSHIELD
SHIELD SHIELD
75ADAPTER
Ohm
ADAPTER
(1/3 WIDTH
REAR
PANEL
ADAPTER)
I/O
(1/3
WIDTH
REAR
PANEL
ADAPTER)
STEREO
ANALOG
ADAPTER
(1/3REAR
WIDTH
REAR
PANEL
ADAPTER)
AES/EBU
ADAPTER
(1/3WIDTH
WIDTH
PANEL
ADAPTER)
RJ-21 ADAPTER
(1/2
REAR PANEL
ADAPTER)
ABC
ABC
Model
#A-3
Model
#A-6
Model
#A-2
Model
#A-5
Model
#A-4
STUDIOHUB+
PATCH
48ABC
110BOARD
PUNCH-DOWN
ABC
ABC
ABC BOARDABC
STUDIOHUB+
PATCH
48 I/O BOARD
STUDIOHUB+
PATCH
48 RJ-21
STUDIOHUB+
PATCH
48 AES/EBU
BOARD
J4
J3
J2
J1
ABC
J1
JU8
JU7
JU6
JU5
JU4
JU3
JU2
JU1
JU8
JU7
JU6
JU5
JU4
JU3
JU2
JU1
JU7
JU5
JU4
JU3 SHIELD JU2
JU1 SHIELD
JU8
SHIELD
SHIELD JU6 SHIELD
SHIELD
SHIELDBOARD
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
BNC 75
OHM
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
110
ADAPTER
(1/3
WIDTH
REAR
PANEL
ADAPTER)
I/O
ADAPTER
(1/3
WIDTH
REAR
PANEL
ADAPTER)
75
Ohm
ADAPTER
(1/3
WIDTH
REAR
PANEL
ADAPTER)
RJ-21
ADAPTER
(1/2
WIDTH
REAR
PANEL
ADAPTER)
AES/EBU
ADAPTER
(1/3
WIDTH
REAR
PANEL
ADAPTER)
ABC
ABC
Model#A-5
#A-4
Model
Model
#A-6
ABC PATCH
ABC
ABC
ABC
STUDIOHUB+
PATCH
48 PUNCH-DOWN
RJ-21
BOARD BOARD
STUDIOHUB+
48 110
J1
J4
JU1
SHIELD
JU8
SHIELD
JU7
SHIELD
J3
J2
ABC
ABC
JU6
JU5
JU4
JU3
75 OHM BOARD
SHIELD BNC
SHIELD
SHIELD
SHIELD
JU2
SHIELD
JU1
SHIELD
75
Ohm
ADAPTER
(1/3
WIDTH
REAR
PANEL
ADAPTER)
RJ-21
ADAPTER
WIDTH
REAR
PANEL
ADAPTER)
110
ADAPTER
(1/3(1/2
WIDTH
REAR
PANEL
ADAPTER)
Model #A-6
STUDIOHUB+ PATCH 48 110 PUNCH-DOWN BOARD
J4
J3
JU8
SHIELD
JU7
SHIELD
JU6
SHIELD
J1
J2
JU5
SHIELD
JU4
SHIELD
JU3
SHIELD
JU2
SHIELD
110 ADAPTER (1/3 WIDTH REAR PANEL ADAPTER)
JU1
SHIELD
JU1
SHIELD
JU8
SHIELD
JU7
SHIELD
JU6
JU5
JU4
JU3
SHIELD BNC
SHIELD
SHIELD
SHIELD
75 OHM BOARD
ABC
JU2
SHIELD
ABC
JU1
SHIELD
Patch48 - 2 row x 24 RJ-45 jacks with front panel normalling switches.
75 Ohm ADAPTER (1/3 WIDTH REAR PANEL ADAPTER)
AES/EBU
Model
Model#A-4
#A-2
Model
#A-6
48 Channel Patch Panel - Equip with any mix of up to six of the following rear panel adapters
PATCH-48795.00
ABC
ABC
ABC
ABC
JU8 JU8
SHIELD
JU7
SHIELD
ABC
ABC
STUDIOHUB+
PATCH
AES/EBU BOARD
STUDIOHUB+
PATCH
48 11048
PUNCH-DOWN
BOARD
J3
ABC
JU6
BNCJU5
75 OHM
SHIELD
SHIELD
ABC
J1
J2
JU4
BOARD
SHIELD
JU3
SHIELD
SHIELD
JU2
SHIELD
JU1
SHIELD
75
Ohm ADAPTER
(1/3 WIDTH
REAR
PANEL
ADAPTER)
AES/EBU
ADAPTER
WIDTH
REAR
PANEL
ADAPTER)
110 ADAPTER
(1/3 (1/3
WIDTH
REAR
PANEL
ADAPTER)
Model #A-4
Model #A-6
Rear Panel Removeable
Adapters- two or three wide across
4 RJ-45’s for stereo analog connections
2 RJ-45’s for AES/EBU connections
8 RJ-45’s for Model
straight-thru
connections
#A-6
8 BNC connectors for 50 Ohm BNC connections
RJ-21 connectors (use 2 across, or 4 total)
8 110 punchdown connections
4 stereo RJ-45 inputs to 8 “Left, Left” RJ-45 outputs
ABC
ABC
ABC PATCH
ABC
ABC
ABC
STUDIOHUB+
48 110 PUNCH-DOWN
BOARD
J3
JU8
SHIELD
JU7
SHIELD
JU6
SHIELD
JU5
ABC
ABC
J1
J2
JU4
JU3
SHIELD
BNC
75 OHM BOARD
SHIELD
SHIELD
JU2
SHIELD
JU1
SHIELD
75
ADAPTER
WIDTH
REAR
PANEL
ADAPTER)
110Ohm
ADAPTER
(1/3 (1/3
WIDTH
REAR
PANEL
ADAPTER)
STUDIOHUB+ PATCH 48 110 PUNCH-DOWN BOARD
J4
J1
JU2
SHIELD
ABC
ABC
ABC BOARD
ABC
STUDIOHUB+
PATCH 48 AES/EBU
J4
JU1
SHIELD
JU3
SHIELD
Model
Model #A-2
#A-4
ABC
J4
JU1
SHIELD
)
APTER)
U1
SHIELD
JU6
JU6
JU5
JU6
JU5
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
STEREO
ANALOG
ADAPTER
WIDTH
REAR
PANEL
ADAPTER)
AES/EBU
ADAPTER
(1/3 (1/3
WIDTH
REAR
PANEL
ADAPTER)
I/O ADAPTER
(1/3 WIDTH
REAR
PANEL
ADAPTER)
JU4
SHIELD
AES/EBU ADAPTER (1/3 WIDTH REAR PANEL ADAPTER)
J3
JU8
SHIELD
JU7
SHIELD
JU6
SHIELD
J1
J2
JU5
SHIELD
JU4
SHIELD
JU3
SHIELD
JU2
SHIELD
110 ADAPTER (1/3 WIDTH REAR PANEL ADAPTER)
JU1
SHIELD
PATCH-48A1
PATCH-48A2
PATCH-48A3
PATCH-48A4
PATCH-48A5
PATCH-48A6
PATCH-48A7
n/c
n/c
n/c
125.00
n/c
n/c
n/c
48 Channel Patch Panel - equipped with six rear panel 50 Ohm BNC connectors.
PATCH-48BNC1,265.00
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
23
STUDIOHUB+ HUBS
Factory
Description
Part #
Price
Source Gear Interconnection
HUB16-DC
16 Channel RJ-45 Hub with DC-Link
16 I/O channels with 2 RJ-45’s and 110 punch connectors.
Adds DC-Link compatability with optional PS-EXTU.
HUB16-DC
295.00
8 Channel RJ-45 Hub with DC-Link
Same as above - 1/2 Hub/single board/8 channel version
HUB8-DC
195.00
Dual Stereo Analog Distribution Amplifier
2 stereo inputs to 12 stereo outputs. Individual level sets. DA12-DC695.00
Single Stereo Analog Distribution Amplifier
Same as above - 1/2 Hub/single board/6 channel version.
DA6-DC495.00
HUB8-DC
ACTIVE HUBS
DA6-DC
DA12-DC
FOUR-STUDIOSW
Four Channel Studio Switcher Hub
Stereo four channel switcher with arming logic.
Supports two or four studio push button panels (Unit has an integrated power supply.)
FOUR-STUDIOSW
695.00
32 Channel mini-Amp Hub
32 channels of audio break-outs from rear mini-Amp connectors to
front panel RJ-45’s in a 1 RU mount. Internally programmable
per channel for analog stereo, mono or AES/EBU
HUB32
495.00
12 Channel Break-Out-Box
8 output channels and 4 input channels of custom break out for
4000, 5000, & 6000 ASI series audio cards in a 1 RU mount.
Front panel SCSI connectors, break out analog & digital
card signals.
HUB12
295.00
Part numbers in red require DC power. See power supply options.
Break-Out Harnessing
HUB32
HUB12
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
24
STUDIOHUB+ PRODUCT PACKAGES
Factory
Description
Part #
Price
Pre-Packaged Cable KITS
Discounted package of various lengths shielded RJ-45 patch cords for all StudioHub+ applications
Mini Patch Cable Kit w/20 Patch Cables 1 each of 1’, 2’, 3’, 20’, 25’ shielded patch cables,
3 each 5’, 7’, 10’, 12’, 15’ shielded patch cables
SH-PATCHKITMN
75.00
Small Patch Cable Kit w/35 Patch Cables 2 each of 1’, 2’, 3’, 20’, 25’ shielded patch cables,
5 each 5’, 7’, 10’, 12’, 15’ shielded patch cables
SH-PATCHKITSM 150.00
Medium Patch Cable Kit w/55 Patch Cables 3 each of 1’, 2’, 3’, 20’, 25’ shielded patch cables,
8 each 5’, 7’, 10’, 12’, 15’ shielded patch cables
SH-PATCHKITMD 250.00
Large Patch Cable Kit w/75 Patch Cables SH-PATCHKITLG 350.00
5 each of 1’, 2’, 3’, 20’, 25’ shielded patch cables,
10 each 5’, 7’, 10’, 12’, 15’ shielded patch cables
Pre-Packaged Adapter KITS
Discounted package of various adapters for all StudioHub+ applications
Mini Adapter Kit w/20 Adapters (5) RJ-45 to XLR (female) adapters, (4) RJ-45 to XLR (male) adapters,
(3) RJ-45 to 1/4” adapters, (4) RJ-45 to bare ends,
(2) RJ-45 to RCA (male), (2) RJ-45 to 1/8” mini (male)
ADAPT-KITMN
350.00
ADAPT-KITSM
725.00
Medium Adapter Kit w/60 Adapters ADAPT-KITMD
(20) RJ-45 to XLR (female) adapters, (15) RJ-45 to XLR (male) adapters,
(5) RJ-45 to 1/4” adapters, (5) RJ-45 to bare end,
(5) RJ-45 to RCA (male), (5) RJ-45 to 1/8” mini (male)
975.00
Small Adapter Kit w/40 Adapters (12) RJ-45 to XLR (female) adapters, (8) RJ-45 to XLR (male) adapters,
(5) RJ-45 to 1/4” adapters, (5) RJ-45 to bare end,
(5) RJ-45 to RCA (male), (5) RJ-45 to 1/8” mini (male)
Large Adapter Kit w/80 Adapters ADAPT-KITLG1,350.00
(20) RJ-45 to XLR (female) adapters, (15) RJ-45 to XLR (male) adapters,
(15) RJ-45 to 1/4” adapters, (15) RJ-45 to bare end,
(10) RJ-45 to RCA (male), (5) RJ-45 to 1/8” mini (male)
STUDIOHUB+ Pre-Packaged STUDIO KITS
Includes patch cables and adapters to connect your console to source equipment inputs and outputs.
Package priced lower than purchasing individual products.
Small Studio Kit
(5) XLR Female Adapters
(3) XLR Male Adapters
(1) 1/4” TRS Adapters
(1) Pigtail Adapters
(1) RJ-45 to RCA (male)
(1) RJ-45 to 1/8” mini (male)
(4) 7’ CAT-5 Shielded Patch Cords
(6) 10’ CAT-5 Shielded Patch Cords
(6) 12’ CAT-5 Shielded Patch Cords
(4) 15’ CAT-5 Shielded Patch Cords
Medium Studio Kit
(7) XLR Female Adapters
(5) XLR Male Adapters
(2) 1/4” TRS Adapters
(2) Pigtail Adapters
(2) RJ-45 to RCA (male)
(2) RJ-45 to 1/8” mini (male)
(10) 7’ CAT-5 Shielded Patch Cords
(10) 10’ CAT-5 Shielded Patch Cords
(5) 12’ CAT-5 Shielded Patch Cords
(5) 15’ CAT-5 Shielded Patch Cords
Large Studio Kit
(10) XLR Female Adapters
(5) XLR Male Adapters
(3) 1/4” TRS Adapters
(3) Pigtail Adapters
(2) RJ-45 to RCA (male)
(2) RJ-45 to 1/8” mini (male)
(10) 7’ CAT-5 Shielded Patch Cords
(12) 10’ CAT-5 Shielded Patch Cords
(10) 12’ CAT-5 Shielded Patch Cords
(8) 15’ CAT-5 Shielded Patch Cords
Part #: SH-STUDIOKITSM
Factory Price: $325.00
Part #: SH-STUDIOKITMD
Factory Price: $475.00
Part #: SH-STUDIOKITLG
Factory Price: $625.00
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
25
STUDIOHUB+ pACKAGES FOR AXIA, WHEATSTONE & LOGITEK
Factory
Description
Part #
Price
Discounted package of various lengths shielded RJ-45 patch cords and adapters to install specific platforms.
AXIA NODE KIT- w/ADAPTERS & PATCH CORDS
SH-ADAPTKITAX350.00
IP Kit w/16 Adapters and Patch Cords for AXIA Nodes
8 RJ-45 to XLRF adapters, 8 RJ-45 to XLRM adapters, sixteen 7’ patch cables
AXIA NODE KIT- w/MALE RJ-45 & XLR CABLES
SH-CABLEKITAX375.00
IP Kit w/8 RJ-45M to XLRF cables and 8 RJ-45M to XLRM cables
WHEATSTONE BLADE KIT
SH-ADAPTKITWH375.00
IP Kit w/GPI Adapter, 16 Adapters and Patch Cords for WHEATSTONE Blades
One Dual RJ45 Breakout adapter to push terminals, 8 RJ-45 to XLRF adapters,
8 RJ-45 to XLRM adapters, sixteen 7’ patch cables
WHEATSTONE AIR-1 KIT
SH-ADAPT-KITAIR1495.00
Console Kit w/four XLRF, two XLRM, two TRSM, two MINIM
two RCAM, twelve 6’ TRSM to RJ-45M Cables
WHEATSTONE AIR-4 KIT
SH-ADAPT-KITAIR4775.00
Console Kit w/twenty-one XLRF, four XLRM, two TRSM, four TAIL, four MINIM
four RCAM, twenty-nine 7’, four 3’ & four 10’ patch cables
WHEATSTONE AIR-5 KIT
SH-ADAPT-KITAIR5995.00
Console Kit w/twenty-four XLRF, four XLRM, four TRSM, four TAIL, four MINIM
four RCAM, twenty-nine 7’, four 3’ & four 10’ patch cables three 3-PIN Cables,
forty 10’ Patch Cables
LOGITEK JETSREAM INPUT KIT
SH-INPUTKITLO85.00
IP Kit w/4 Adapters and Patch Cords for LOGITEK JetStream Input Cards
Four RJ-45 to XLRF adapters, four 10’ patch cables
LOGITEK JETSTREAM OUTPUT KIT
SH-OUTPUTKITLO85.00
IP Kit w/4 Adapters and Patch Cords for LOGITEK JetStream Output Cards
Four RJ-45 to XLRM adapters, four 10’ patch cables
LOGITEK JETSTREAM MIC KIT
SH-MICKITLO85.00
IP Kit w/4 Adapters and Patch Cords for LOGITEK JetStream Microphone Cards
Four RJ-45 to XLRM adapters, four 10’ patch cables
STUDIOHUB+ CONSOLE HARNESS KITS
Wire harness kits for breakout of analog and digital I/O connections to a StudioHub+ HUB36-DC.
Order the specific kit for your console. Hubs, all required audio cables and wiring hoops and documentation included.
12ft. CAT-5 twisted pair wire length standard. Custom lengths may be specified. Remote control wiring not included.
Part #: SH-CONSOLEHARNESSSM
for up to 12 channel consoles
Part #: SH-CONSOLEHARNESSMD
for up to 24 channel consoles
Part #: SH-CONSOLEHARNESSLG
for up to 24+ channel consoles
Kit contains:
(1) Hub 36-DC Breakout Hub
Console specific I/O cables
(10) small wiring hoops
(5) large wiring hoops
Kit contains:
(2) Hub 36-DC Breakout Hub
Console specific I/O cables
(20) small wiring hoops
(10) large wiring hoops
Kit contains:
(3) Hub 36-DC Breakout Hub
Console specific I/O cables
(30) small wiring hoops
(15) large wiring hoops
Factory Price: $995.00
Factory Price: $1,495.00
Factory Price: $1,995.00
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
26
STUDIOHUB+ MOUNTS
Factory
Description
Part #
Price
MOUNTS FOR PANELS
“Rack-up” any combination of active or passive StudioHub+ plates
SH-WELL1 SH-WELL2 SH-WELL3
In Table Well Mounts
Single Dual Triple Quad
Blank Filler Panel
SH-WELL1 SH-WELL2 SH-WELL3 SH-WELL4
SH-BLANK
On Table Surface Mounts
Single
Dual Triple Quad
SH-SURF135.00
SH-SURF2
40.00
SH-SURF3
45.00
SH-SURF450.00
Rack Mounts
4 Position 1 RU
SH-RACK4 45.00
10 Position 3 RU
SH-RACK10
75.00
Table Mounts
Consolette 4 Position Mount Four Across Mount - Mounts to flat surface
SH-CON
SH-FLAT4
225.00
40.00
Under Countertop Mount
SH-MOON75.00
25.00
30.00
35.00
40.00
12.00
SH-SURF1 SH-SURF2 SH-SURF3
SH-RACK4
SH-RACK10
SH-CON
Includes wood consolette
and 4-position metal mount.
Electronic panels shown
available separately.
SH-FLAT4
Includes mounting hardware and
template. Intended for flat surface
mount.
SH-MOON
Includes under table mount.
Headphone amp shown available
separately.
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
ORDERING INFORMATION
Warranty
Warranty is two years for consoles, one year for all other products. All factory non-warranty service is guaranteed for 90 days.
For full warranty information, refer to the product manual.
Technical assistance is available during normal business hours at no charge by telephone or written correspondence. Items to
be returned for repair must include a Return Authorization number obtained from Radio Systems.
Shipping
Prices are FOB Logan Township, NJ. Shipping charges are the responsibility of the buyer. The customer bears the risk of loss
from the point of shipment. Upon request, Radio Systems will drop ship an order to a third party at no additional charge.
Ordering
Radio Systems will accept orders via mail, telephone, fax or e-mail from authorized dealers. However, in case of phone, fax or
e-mail orders, we must receive the signed original marked “Confirming.”
Power
All Radio Systems products operate at 110v/220v, 60Hz/50Hz power. Certain products may require voltage selector switch to be
enabled. Refer to product manual for details.
Specifications
Radio Systems reserves the right to make changes in specifications and/or pricing without notice. Whenever possible, however,
we will make every effort to notify the dealer of the change(s).
Shipping Weights and Measurements
Product
Dimensions (inches)
Weight
6 Channel Console With Power Supply
40 x 34 x 15
105 lbs. (dim wt.)
12 Channel Console
40 x 34 x 15
105 lbs. (dim wt.)
Console Power Supply
26 x 15 x 14
20 lbs.
18 Channel Console
52 x 34 x 15
137 lbs. (dim wt.)
24 Channel Console
64 x 34 x 15
165 lbs. (dim wt.)
DA 4x4b
23 x 13 x 3
8 lbs.
CT-THIN
7 x 2.5 x 1.25
3 lbs.
CT-DESK
7 x 2.5 x 4.5
3 lbs.
CT-2INCH
20 x 9 x 8
7 lbs.
CT-4INCH
28 x 18 x 6
15 lbs.
Rev. 1-01-2017
Adding ADA-2x8SS
Adding SH-MICPTTPLUS
Adding RS-IP Consoles
Deleted RS-A Analog Consoles
Radio Systems, Inc. • 601 Heron Drive • Logan Township, NJ 08085 • phone: 856-467-8000 • fax: 856-467-3044 • email: [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement