Cisco Explorer 8700 Cable DVR Family Set-Tops Quick

Cisco Explorer 8700 Cable DVR Family Set-Tops Quick
IMPORTANT SAFETY INSTRUCTIONS
Notice to Installers
The servicing instructions in this notice are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions, unless you are qualified to do so.
Quick Reference Guide
Note to System Installer
For this apparatus, the coaxial cable shield/screen shall be
grounded as close as practical to the point of entry of the cable
into the building. For products sold in the US and Canada, this
reminder is provided to call the system installer's attention to
Article 820-93 and Article 820-100 of the NEC (or Canadian
Electrical Code Part 1), which provides guidelines for proper
grounding of the coaxial cable shield.
CAUTION: To reduce the risk of electric shock, do not
remove cover (or back). No user-serviceable parts
inside. Refer servicing to qualified service personnel.
WARNING
TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This symbol is intended to alert you that uninsulated voltage
within this product may have sufficient magnitude to cause
electric shock.Therefore, it is dangerous to make any kind of
contact with any inside part of this product.
Ce symbole a pour but d’alerter toute personne qu’un contact
avec une pièce interne de ce produit, sous tension et non isolée,
pourrait être suffisant pour provoquer un choc électrique. Il est
donc dangereux d’être en contact avec toute pièce interne de
ce produit.
Cisco Explorer 8700 Cable DVR Family Set-Tops
This symbol is intended to alert you of the presence
of important operating and maintenance (servicing)
instructions in the literature accompanying this product.
Ce symbole a pour but de vous avertir qu’une
documentation importante sur le fonctionnement et
l’entretien accompagne ce produit.
SELECT
20080814_Installer820
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Article 810 of the National Electric Code (NEC) ANSI/NFPA No. 70-1990,
provides the following information:
• Grounding of the mast and supporting structure
• Do not expose batteries to excessive heat (such as sunlight or fire).
• Connection to grounding electrodes
• Do not expose batteries to temperatures above 100°C (212°F).
• Requirements for the grounding electrodes (see the following antenna
grounding diagram as recommended by NEC ANSI/NFPA 70)
Battery Disposal
WARNING: Avoid electric shock and fire hazard! Do
not locate an outside antenna system in the vicinity of overhead
power lines or power circuits. Touching power lines or circuits
might be fatal.
A label on this product indicates the correct power source for this product.
Operate this product only from an electrical outlet with the voltage and
frequency indicated on the product label. If you are uncertain of the type of
power supply to your home or business, consult your service provider or
your local power company.
• The batteries may contain substances that could be harmful to the
environment.
• Recycle or dispose of batteries in accordance with the battery
manufacturer’s instructions and local/national disposal and recycling
regulations.
• The batteries may contain perchlorate, a known hazardous substance,
so special handling and disposal of this product might be necessary.
For more information about perchlorate and best management
practices for perchlorate-containing substance, see www.dtsc.ca.gov/
hazardouswaste/perchlorate
Provide Ventilation and Select a Location
• Remove all packaging material before applying power to the product.
Check Product Safety
Upon completion of any service or repairs to this product, the service
technician must perform safety checks to determine that this product is in
proper operating condition.
• Do not place this apparatus on a bed, sofa, rug, or similar surface.
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from
tip-over.
Power Source Warning
Explorer ® 8742HDC
• Replace batteries with the same or equivalent type that we recommend.
• Location of the antenna-discharge unit
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
• Do not place this apparatus on an unstable surface.
Protect the Product When Moving It
• Do not install this apparatus in an enclosure, such as a bookcase or rack,
unless the installation provides proper ventilation.
Always disconnect the power source when moving the apparatus or
connecting or disconnecting cables.
• Do not place entertainment devices (such as VCRs or DVDs), lamps,
books, vases with liquids, or other objects on top of this product.
20110316_Cable_Safety
• Do not block ventilation openings.
T11518
Protect the Product from Lightning
In addition to disconnecting the AC power from the wall outlet, disconnect
the signal inputs.
Verify the Power Source from the On/Off Power
Light
When the on/off power light is not illuminated, the apparatus may still be
connected to the power source. The light may go out when the apparatus is
turned off, regardless of whether it is still plugged into an AC power source.
Eliminate AC Power/Mains Overloads
Operating Environment
The set-top is designed for operation indoors with a temperature range from
32° to 104° F (0° to 40°C). Each set-top should have adequate spacing
on all sides so that the cooling air vents on the chassis are not blocked.
Protect from Exposure to Moisture and Foreign
Objects
WARNING: Avoid electric shock and fire hazard! Do not
expose this product to dripping or splashing liquids, rain, or moisture.
Objects filled with liquids, such as vases, should not be placed on
this apparatus.
United States FCC Compliance
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against such interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy. If not installed and used in accordance with the instructions, it may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment OFF and ON, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
The AC inlet on the unit must remain accessible and operable at all times.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Ground the Product
• Consult the service provider or an experienced radio/television technician
for help.
WARNING: Avoid electric shock and fire hazard! If this product
connects to coaxial cable wiring, be sure the cable system is grounded
(earthed). Grounding provides some protection against voltage surges
and built-up static charges.
Outdoor Grounding System
If this product connects to an outdoor antenna or cable system, be sure
the antenna or cable system is grounded (earthed). This provides some
protection against voltage surges and built-up static charges.
VOL
CH
• Insert batteries correctly. There may be a risk of explosion if the batteries
are incorrectly inserted.
• Please follow instructions provided for charging ‘rechargeable’ batteries.
• Size of the grounding conductors
11) Only use attachments/accessories specified by the
manufacturer.
14) Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as a power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
VOL
Battery Safety
• Do not attempt to recharge ‘disposable’ or ‘non-reusable’ batteries.
• Grounding the lead-in wire to an antenna discharge unit
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
12)
CH
WARNING: Avoid electric shock and fire hazard! Do not
overload AC power/mains, outlets, extension cords, or integral
convenience receptacles. For products that require battery power
or other power sources to operate them, refer to the operating
instructions for those products.
WARNING: Avoid electric shock and fire hazard! Unplug
this product before cleaning. Do not use a liquid cleaner or an
aerosol cleaner. Do not use a magnetic/static cleaning device (dust
remover) to clean this product.
Handling Disposable Batteries
This product may contain disposable batteries. Heed the following warning
and follow the Battery Safety and Battery Disposal instructions below.
WARNING: There is danger of explosion if the battery is
mishandled or incorrectly replaced. Replace only with the same type
of battery. Do not disassemble it or attempt to recharge it outside
the system. Do not crush, puncture, dispose of in fire, short the
external contacts, or expose to water or other liquids. Dispose of
the battery in accordance with local regulations and instructions
from your service provider.
WARNING: Avoid electric shock and fire hazard! Never
push objects through the openings in this product. Foreign objects
can cause electrical shorts that can result in electric shock or fire.
Service Warnings
WARNING: Avoid electric shock! Do not open the cover
of this product. Opening or removing the cover may expose you to
dangerous voltages. If you open the cover, your warranty will be
void. This product contains no user-serviceable parts.
Cisco Explorer 8700 Cable DVR Family Set-Tops
ROVI CORPORATION COPYRIGHT NOTICE
Manufactured by:
Cisco Systems, Inc.
5030 Sugarloaf Parkway
Lawrenceville, Georgia 30044 USA
Telephone: 770 236-1077
This product incorporates copyright protection technology that is protected
by U.S. patents and other intellectual property rights. Use of this copyright
protection technology must be authorized by Rovi Corporation, and is
intended for home and other limited viewing uses only unless otherwise
authorized by Rovi Corporation. Reverse engineering or disassembly is
prohibited.
Canada EMI Regulation
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme NMB-003
du Canada.
20081121 FCC Standard
Disclaimer
Cisco Systems, Inc. assumes no responsibility for errors or omissions that
may appear in this guide. We reserve the right to change this guide at any
time without notice.
AVC VIDEO LICENSE
With respect to each AVC/H.264 product, we are obligated to provide the
following notice:
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO
LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES
IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO
IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii)
DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN
A PERSONALACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER
LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL
BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE
OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM.
Accordingly, please be advised that service providers, content providers, and
broadcasters may be required to obtain a separate use license from MPEG
LA prior to any use of AVC/H.264 encoders and/or decoders.
Any changes or modifications not expressly approved by Cisco Systems,
Inc., could void the user’s authority to operate the equipment.
The information shown in the FCC Declaration of Conformity paragraph below
is a requirement of the FCC and is intended to supply you with information
regarding the FCC approval of this device. The phone numbers listed are
for FCC-related questions only and not intended for questions regarding the
connection or operation for this device. Please contact your service provider
for any questions you may have regarding the operation or installation of
this device.
Declaration of Conformity
This device complies with Part 15 of FCC Rules. Operation is subject to the
following two conditions: 1) the device may not cause harmful interference,
and 2) the device must accept any interference received, including
interference that may cause undesired operation.
Cisco Systems, Inc.
5030 Sugarloaf Parkway, Box 465447
Lawrenceville, GA 30042
678 277-1120
770 722-2009
www.cisco.com
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. A listing of Cisco’s trademarks can be
found at www.cisco.com/go/trademarks.
CableCARD and M-Card are trademarks of Cable Television Laboratories, Inc.
Manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories.
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Rovi is a trademark of Rovi Corporation.
MoCA is a trademark of the Multimedia over Coax Alliance.
Other third party trademarks mentioned are the property of their respective owners.
The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1009R)
©2011 Cisco and/or its affiliates. All rights reserved.
April 2011
Printed in United States of America
Part Number 4038345 Rev B
Welcome
Front Panel
Connecting to an HDTV with HDMI Input
The Cisco® Explorer ® 8700 Cable DVR Family set-tops receive and
deliver digital signals, and deliver high-definition programming in
exceptional picture and audio quality. Use the simple user interface
to access favorite channels and parental control services. Contact
your service provider for information about these and other available
services. Use the instructions in this guide to install the set-top and to
access your program services.
1. Unplug all electronic devices before connecting the set-top.
2. Connect the set-top and TV to the HDMI input as shown in the diagram.
CH
SELECT
3. Connect the set-top to the coaxial cable coming in from the wall.
VOL
VOL
4. Plug the TV into an AC power source.
CH
The consumer support website provides news and information about
this product. For more information, please refer to:
5. Plug the set-top’s power cord into an AC power source.
6. For the TV to receive the signal, press the appropriate button on the remote control to select the audio/video inputs to which you have
connected the set-top.
Explorer ® 8742HDC
7. Press the POWER key on the remote control.
http://www.cisco.com/web/consumer/support/index.html
1
Safety First
Before using this set-top read the IMPORTANT SAFETY
INSTRUCTIONS section of this guide.
Avoid Screen Burn-In
Images such as letterbox bars or side bars, bright closed-captioning
backgrounds, station logos, or any other stationary images may cause the
TV screen to age unevenly and cause damage to your TV. Refer to the user
guide that came with your TV for more information about screen burn-in.
Performance Tips
3
4
5
6
Turns the set-top on and off
2 Guide
Accesses on-screen services, such as the on-screen guide,
video-on-demand, or pay-per-view
3 Info
10
T14868
Safety and Performance Tip
L
Pb
R
Pr
IR
MCARD SN: XXXXXXXXX
AVIS: RISQUE DE CHOC
ÉLECTRIQUE NE PAS OUVRIR
5 Exit
Exit menus, the on-screen menu, and program information
6 USB 2.0
Connects to external USB equipment approved by your service provider, software controlled
7 Display
Displays the selected channel number and time of day. The display shows the following:
• MoCA™ Link ( )
• 480i / 480P
• 5.1
• Power ( )
• Message (
)
• HDTV
• 720i / 720P
• Record (
)
• Auto
• 1080i / 1080P
8 Select
Accesses your on-screen selection
9 VOL-, VOL+
Decreases and increases the volume
THIS DEVICE IS INTENDED TO BE ATTACHED TO A RECEIVER THAT
IS NOT USED TO RECEIVE OVER-THE-AIR BROADCAST SIGNALS.
CONNECTIONS OF THIS DEVICE IN ANY OTHER FASHION MAY
CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS
AND IS IN VIOLATION OF THE FCC RULES, PART 15.
CABLE IN
CATV CONVERTER
MADE IN MEXICO
MCARD MAC: XXXXXXXXXXXX
OPTICAL
AUDIO OUT
CABLE OUT
Cable
Input
eSATA
USB 2.0
AUDIO
CENTER
CHANNEL IN
1394
+12VDC
3A
HDMI
Scrolls up and down through the channels
Note: This illustration may vary from the actual product.
ON
WARNING: Electric
shock hazard! Unplug a l l
electronic devices before
connecting or disconnecting
any device cables to the set-top.
Back Panel
• If the set-top is plugged into a wall switch, verify the switch is in the
ON position. (Avoid plugging into an outlet that is controlled by a
wall switch.)
OUTPUT
VIDEO
STB SN: XXXXXXXXX
LISTED 36MW
VIDEO PRODUCT
• Verify that all cables are properly connected.
CAUTION
L
Pb
R
Pr
IR
ETHERNET
AVIS: RISQUE DE CHOC
ÉLECTRIQUE NE PAS OUVRIR
THIS DEVICE IS INTENDED TO BE ATTACHED TO A RECEIVER THAT
IS NOT USED TO RECEIVE OVER-THE-AIR BROADCAST SIGNALS.
CONNECTIONS OF THIS DEVICE IN ANY OTHER FASHION MAY
CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS
AND IS IN VIOLATION OF THE FCC RULES, PART 15.
T15010
• Adjust the TV color controls.
R
Y
AUDIO
MCARD SN: XXXXXXXXX
CATV CONVERTER
MADE IN MEXICO
PB
L
PR
AUDIO
1
2 3 4
5
L/
MONO
PB
L
R
PR
AUDIO
R
6 7
eSATA
USB 2.0
8
9 10
11
1394
+12VDC
3A
12 13 14
1 Cable In
Connects to a coaxial cable that delivers the signal from your service provider
No sound
2 Cable Out
Connects to a coaxial cable that sends analog audio and video signals to a TV or VCR
• If your setup includes a VCR or stereo, verify that you have properly
connected them to the set-top.
3 Video Out
Connects to the composite input on your TV
4 Audio Out
Connects to RCA cables that send analog audio signals (left and right) to the stereo inputs on a TV
• Verify the volume is turned up.
5 HDTV (YPbPr)
Connects to the component input (YPbPr) on the HDTV
• Verify the mute function is not on.
6 Optical Audio Out Connects to an optical cable that sends a digital audio signal to a surround-sound receiver or other digital audio
device input
7 IR Remote Input
Available to be connected to an approved remote IR receiver (purchased separately)
8 USB 2.0
Connects to external USB equipment approved by your service provider, software controlled
9 Ethernet
Connects to external Ethernet equipment approved by your service provider
10 HDMI
Connects an HDMI™ cable to the HDMI input of an HDTV. HDMI supports both digital audio and video. May be
used to connect to a DVI interface using an HDMI-to-DVI adapter for video and separate audio connections. Any of
the following audio connections may be used: Audio Out (4) or Optical Audio Out (6)
11 eSATA
Connects to an external Serial ATA (eSATA) hard disk drive for expanded drive space. A connected eSATA drive is
not an archival device. Ask your service provider for a list of approved hard drive models for use with the DVR
12 1394
Connects to display devices that are equipped with a 1394 input
13 AC Power Input
Connects to the power cord to deliver power to the set-top
14 Multi-Stream
CableCARD
Slot for Multi-Stream CableCARD™ module (M-Card), which decrypts subscription digital channels. This set-top will
not operate correctly without an M-Card module, which is installed by your service provider
Note: This illustration may vary from the actual product.
Y
ANT-1
OUT
R
MCARD MAC: XXXXXXXXXXXX
OPTICAL
AUDIO OUT
CABLE OUT
L
ANT (75 )
VIDEO
R
HD 2
HD 2
CABLE IN
No color
S-VIDEO
L/
MONO
STB RF MAC: XXXXXXXXXXXX
RISK OF ELECTRIC SHOCK
DO NOT OPEN
OFF
AUDIO IN
DVI/HDCP
VIDEO
MULTISTREAM
CABLE CARD
Y
eCM MAC: XXXXXXXXXXXX
• The current channel may not be available in your service package.
Try selecting another channel to see if a picture appears.
ETHERNET
STB RF MAC: XXXXXXXXXXXX
RISK OF ELECTRIC SHOCK
DO NOT OPEN
• Verify that the power to your TV is turned on.
• Verify the current TV program is broadcast in color.
MULTISTREAM
CABLE CARD
Y
eCM MAC: XXXXXXXXXXXX
If the set-top does not perform as expected, the following tips may help.
No picture
VIDEO
STB SN: XXXXXXXXX
LISTED 36MW
VIDEO PRODUCT
CAUTION
Displays the recorded list
10 CH+, CH-
OUTPUT
Keep the top of the set-top free of all objects
and electronic devices, including your TV.
Displays a description of the selected program. This button is
available from the on-screen menu and while viewing a program
4 List
9
Back of Set-Top
1 Power
Automatic Software Updates
A message appears on the TV screen when the set-top and the M-Card™
module are receiving software updates. In addition, download information
also appears on the front panel of the set-top during these updates. Wait
for the current time to display on the front panel before continuing. When
the time appears, the update is complete.
2
8
7
Back of HDTV
IN
IN
OUT
IN
ANT-2
T15011
Note: This illustration may vary from the actual product.
Open Source GNU GPL Statement
Cisco Explorer 8700 Cable DVR Family Set-Tops contain(s), in part, certain free/open source software (“Free Software”) under licenses which
generally make the source code available for free copy, modification, and redistribution. Examples of such licenses include all the licenses
sponsored by the Free Software Foundation (e.g. GNU General Public License (GPL), GNU Lesser General Public License (LGPL), Berkeley
Software Distribution (BSD), the MIT licenses and different versions of the Mozilla and Apache licenses). To find additional information regarding
the Free Software, including a copy of the applicable license and related information, please go to: (i) for North America http://www.cisco.com/
web/consumer/support/open_source.html, or (ii) for outside North America http://www.cisco.com/web/consumer/support/open_source.
html#~international. Once at the site, search for the product listing and click on the related items identified. If you have any questions or
problems accessing any of the links, please contact: [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement