banff spas user manual - Quality spa pools from Banff Spas Australia

banff spas user manual - Quality spa pools from Banff Spas Australia
BANFF
SPAS
USER
MANUAL
DEAR
SPA
BUYER
Congratulations on your purchase of
a new Banff Spa. You now possess
the ultimate passport to tranquility – a
miniature vacation at home, ready and
waiting for you in your own backyard!
We want you to enjoy your Spa. Many
hours of research have gone into the
design of your spa, to ensure the
ultimate in hydrotherapy and relaxation.
Only the highest quality components
have been used, to ensure years of
trouble-free operation. Your comfort and
enjoyment has been designed into your
spa from the start.
Please take the time to read through
this Owner’s Manual. In it, you will find
guidelines on caring for your spa, a
complete explanation of the controls,
safety instructions, a troubleshooting
section, and lots more.
Once again, we welcome you to the
family of Banff Spa owners.
Sincerely,
BANFF Team
Banff Spas
CONTENT
Your personal spa record
Drain valve instructions
Safety instructions and warnings
Spa pool maintenance
Important general operating instructions
Basic Installation Information
• Initial start up procedure
Start up or refill checklist
• Check barrel unions are tight
• Check valves are open
• Check drain valve is closed and firmly tightened
• Changing the water
• Total alkalinity
• The pH level
• Sanitising the spa
• Recommended levels
Pump maintenance
Barrel union maintenance
• Check all jets are open
Shutting down your spa
• Fill water to correct level in spa
Troubleshooting
Getting to know your spa
Heat pump connection instructions
• Filter cartridges
• Aromatherapy canister
• Air venturi controls
• Parts supplied
• Tools and parts required
• Water diverters
• Waterfall control dials
01
YOUR
PERSONAL
SPA
RECORD
We appreciate your business and our
sincere desire is that you receive years of
pleasure and therapy from your Banff Spa.
Please call your local spa dealer if you
have any questions or problems.
INSTALLATION DETAILS
Dealer
Installer
Date of delivery
SPA DETAILS
Spa
Model
Serial number
Colour
Equipment pack
02
Circulation pump
Fitted Not fitted
Sanitiser Ozone
UV
Jet pumps 1
Heat pump
Fitted 2
3 4
Not fitted
Size
kw
03
SAFETY
INSTRUCTIONS
AND
WARNINGS
When installing and using this electrical
equipment, basic safety precautions
should be followed, including the following:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2.
WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. KEEP SPA COVER LOCKED WHEN NOT IN USE.
3.
THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED SERVICE TECHNICIAN. All electrical connections must be performed by a licensed electrician and must confirm to all national, state and local electrical codes in effect at time of installation.
4. The appliance must be connected to a suitably rated and weather protected power supply.
04
5.
The supply line should be a dedicated power circuit and means for disconnection must be incorporated in the fixed wiring in accordance with your local wiring regulations.
6.
Means for disconnection from the supply mains should have a contact separation in all poles that provide full disconnection under overvoltage category III conditions.
7. The appliance should be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA.
8. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
9.
The appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure they can use the appliance safely.
10.Young children should be supervised to ensure they do not play with the appliance.
11.In order to avoid the possibility of hyperthermia (heat stress) occurring it is recommended that the average temperature of the spa pool water should not exceed 40oC.
12. The control box, heater, pumps and other electrical items should only be serviced by a qualified spa service technician.
Spa pool safety rules
1. This spa pool is a heated water environment and if you are concerned that it may adversely affected you it is your responsibility to seek a medical advice.
2. NEVER PUT HEAD UNDER WATER.
3. All children must supervised by an adult.
4. Do not use the spa pool area while under the influence of drugs or alcohol (certain medications may produce adverse effects).
5. It is safer not to use the spa pool alone.
6. It is recommended that you use the spa pool for no longer than 15 minutes at a time.
13. Do not operate electrical appliances within 1.5m of the spa.
NOTE: It is the owner’s responsibility to display all required safety notices within view of the spa.
05
IMPORTANT
GENERAL
OPERATING
INSTRUCTIONS
The following operating and maintenance
instructions are very important and must
be followed carefully. With proper care
and maintenance your spa will provide
you with years of satisfaction with
minimum effort.
06
1.
The filtration pump should be operated for a minimum of four (4) hours per day for cleaning and filtering of the spa water. Information on adjusting filter duration can be found in the control panel’s instruction manual.
2.
The length of time required to heat your spa to the desired water temperature will vary, depending on the air temperature, season, and wind velocity. Therefore, this is something each owner must adjust to their desired liking. We highly recommend using the hard cover to minimize heat loss and to protect your spa when not in use.
3. The replaceable filter cartridge is trouble free and easy to clean. A routine cleaning is the best practice. Cartridge should be removed and hosed down weekly using a water hose with pressure nozzle. Make sure all pumps are turned OFF before removing the cartridge for cleaning. In addition, at least once a month the cartridge should be removed and soaked in a filter cartridge cleaning solution for a minimum 30 minutes (or as directed by the cleaning solution’s instructions). After soaking, the cartridge should be thoroughly rinsed using a water hose with pressure nozzle. The frequency of soaking required varies with amount of spa use. The more the spa is used the more often the filter
should be cleaned.
4. Keep the spa water level at least 50mm above the skimmer at all times. Never allow the water level to drop below the bottom of the skimmer opening. If the water level is too low, the skimmer will allow air into the water lines of the pump, causing it to lose its prime (water -flow). Running the pump without water flow will damage the pump seal assembly and could result in further equipment damage, which will not be covered by the product warranty.
5.
It is your responsibility to regularly check and maintain the chemical water balance of the spa pool to ensure it remains within reasonable pH (acid/
alkaline) limits (7.4 - 7.6 pH). Unbalanced water chemistry greatly accelerates corrosion and may lead to early product or component failure. Product or component failures caused as a result of poor water chemistry maintenance will NOT be covered by the product warranty.
6. Your spa may be equipped with an ozone or uv sanitiser to assist with water sanitization and filtration, however your spa water will still require regular treatment with some form of chemical spa sanitiser. Consult your local spa dealer for advice on regular water testing and treatment procedures.
7. You should empty and clean your spa at least every 3-4 months. Performing a pipe and jet degrease before draining is recommended. Drain the spa water and use a liquid cleanser free of abrasives to clean your spa. Fill with regular tap water and chemically treat the water before use, for a clean and healthy spa.
8. CAUTION: Cover must be kept on spa at all times spa shell is empty, direct exposure to sunlight can damage plastic parts and interior surface, jets, or any other interior components. Damage resulting from the above will not be covered under warranty.
07
BASIC
INSTALLATION
INFORMATION
Your new portable spa must be placed on a uniformly flat and level surface. A concrete
pad 100mm thick is recommended. We recommend you contact your local for up to
date fencing regulations and requirements. If your spa is located near sprinklers, adjust
or cap them so as not to hit the siding of the spa.
Initial start up procedure
1.
15 amp spas are supplied with a power cord but must be connected to a weatherproof 15A outlet. 32 amp spa must be hardwired directly to your house supply. All electrical connections must be performed by a licensed electrician and must confirm to all national, state and local electrical codes in effect at time of install.
2. DO NOT turn power ON to the spa until it is filled with water.
300mm
3. Remove the cabinet door panel on the electronic keypad side of the spa and check that the pump(s) and heater barrel unions are tightened (NOTE: It is possible for these connections to become loose during transportation). Also check that all T-handled gate vales are pulled UP in the open position.
4. Ensure that the external drain valve is firmly tightened and the jets are in the open position.
5. Remove filter from the spa and insert your garden hose down the filter lines for at least 5 minutes. This will flood the pipework of the spa and help prevent air locks in the pipework.
7. Once spa has been filled with water to the correct level, plug the power cord into the power point and switch the power ON. If the spa is hardwired, switch the spa ON at the isolation switch. Any switches should be located within 3 metres of the spa.
8. The filtration pump will start immediately after the power is turned on. ENSURE YOU SEE WATER CIRCULATING. If water is not moving, switch the spa off and refer to the troubleshooting guide in this manual: PUMPS RUN BUT NO WATER MOVING.
9. Once you have the water circulating, adjust the water temperature to the desired level and set the time (please refer to separate instructions provided for the control panel).
10.Add and adjust your chemicals to the spa water following the chemical start up procedure supplied to you by your spa dealer.
11.Ensure that the hard cover is fitted to the spa as this will greatly reduce heat up time.
6. Your spa should be filled until the water level is at least 50mm above the skimmer.
08
09
START UP
OR REFILL
CHECKLIST
Remove spa cabinet side panel (on keypad side) to access equipment bay
1. Check Barrel Unions are tight
3. Check drain valve is closed and firmly tightened
Barrels unions are the connections between the pumps and heater and the plumbing of the spa. If they become loose, this can cause water loss. It is important to check the tightness of these unions periodically, and especially when spa is first delivered. The unions are designed to be retightened by hand. Rotate the locking nut clockwise to tighten.
Please refer below illustration showing the valve being closed.
NOTE: If you see water escaping from beneath your spa, the barrel unions should be the first thing you check. LEAKS FROM BARREL UNIONS ARE NOT COVERED BY THE SPA’S WARRANTY.
2. Check valves are open
T-handled valves enable the water flow to be closed to allow removal of spa equipment for servicing without the need to empty the spa water. The T handles must be pulled UP to be OPEN and allow water flow, and they should be secured open with clips.
Valves
(open)
Barrel
Unions
4. Check all jets are open
Water flow to most jets can be turned on or off by rotating the jet face clockwise (on) or anti-clockwise (off). Check to ensure all jets are open before filling with water.
On
Off
5. Fill water to correct level in spa
The spa should be filled until the water level is at least 50mm above the skimmer.
NOTE: Always remember to remove the filters and fill spa through filter pipes
10
11
GETTING
TO KNOW
YOUR SPA
Your new Banff portable spa has many
features to help adjust and customize the
water flow to your chosen configuration
and enjoyment. Individual jets can be
turned on and off, aeration to water flow
can be adjusted, water can be diverted to
certain specific zones and jets of the spa
or mixed throughout, and waterfalls and
fountains can be turned on and off. The
following pages and pictures will give you
a brief overview of how to adjust and use
some of the various features.
Filter Cartridges
Your spa is equipped with one filter cartridge. This filter will
do most of the hard work in keeping your water clean.
NOTE: Filter cartridges may require replacement or cleaning more frequently depending on length and frequency of regular spa use.
Removing the filter
To remove filter simply unscrew the cartridge in an anticlockwise direction and pull out from spa pool.
Reinstalling filter
When reinstalling filter first hold the cartridge underwater
until the air stops bubbling (at this point most air has been
removed from the cartridge). Then screw the cartridge
back into place in a clockwise direction.
NOTE: DO NOT screw the cartridge back into place excessively tight. Only screw the cartridge until it no longer spins freely. The suction from the pumps will pull the cartridges in further once operated. If the cartridge is screwed in place excessively tight before pump operation, the cartridge may be difficult to remove or could even cause the filter thread connection to twist or break the next time the cartridge is removed and breakage is not covered by warranty.
12
13
GETTING
TO KNOW
YOUR SPA
Air Venturi Controls
DRAIN VALVE
INSTRUCTIONS
Open: How to open valve and connect hose
1
2
3
4
Each zone of your spa will have an air venturi control. This
regulates the amount of air that flows through the jet with
the water. The more air, the more powerful the jet’s stream.
You can adjust the pressure in the entire seat by adjusting
this air venturi control clockwise or anti-clockwise.
NOTE: Upon completion of spa use the air venturi controls should be turned back to the OFF position (no air through jets). This prevents air entering the spa and cooling the water when
spa not in use.
Closed: How to disconnect hose and close valve
5
6
7
8
Water Diverters
Your spa may be fitted with one or more water flow
diverters. These diverters control the flow of water from
each jet pump between various zones of the spa. You can
have full pressure in one zone and no pressure in another
zone by turning the diverter handle all the way to the left or
right, or part pressure in each zone by setting the diverter
handle to the middle position.
NOTE: It is important NOT to push these diverter handles past the natural stop point as breakage is not covered by the spa’s warranty.
Waterfall Control Dials
Your spa may also be fitted with one or more waterfalls
and back lit water cascade. These water features operate
with either the filtration or jet pump and can be turned
on or off by rotating the control dial(s) clockwise or anticlockwise. Similar in appearance to air venturi controls
however their larger size and higher profile makes them
easily distinguishable.
14
15
SPA POOL
MAINTENANCE
If you own a spa pool or hot tub, it is
important to understand that it requires
a certain amount of owner maintenance
to ensure it operates properly and that
the water remains clean and healthy. The
water treatment requirements for a spa
pool differ from those for a swimming
pool, because you are dealing with
hot water. Hot water requires different
treatment to prevent the growth of
bacteria and algae.
The correct use of chemicals will maintain
the water in a clean and healthy condition.
The parameters that need to be regularly
checked are, total alkalinity, pH and
sanitiser level. Your local spa retailer should
be able to supply a suitable test kit and
advise on its correct use. It is advisable to
test the water on a daily basis.
SPECIAL NOTE: Do not mix chemicals. Do not add water to the chemicals, only add chemicals to the water
IMPORTANT:
16
Not maintaining your water chemistry can void parts of your spa warranty.
Changing the water
Sanitising the spa
The spa water should be changed every three to four
months, or remove and replace approx 30% or 1/3 of the
volume of water every three to four weeks.
Sanitising your spa is essential for safe, healthy water,
free of harmful micro-organisms. The most commonly
used sanitiser for spa pools is a form of chlorine (Lithium
Hypochlorite). Ozone or UV may also be used, but
because there can be no residual, a form of chlorine must
be used in conjunction with it.
Total alkalinity
The total alkalinity should be in the range of 90 - 150 ppm
(parts per million). A spa or hot tub with low total alkalinity
would require constant adjustment of the pH. To raise
total alkalinity, add sodium bicarbonate in small quantities.
To lower the total alkalinity, add acid (Dry Acid – Sodium
Bisulphate) in small quantities. Test in one hour.
The pH level
pH is the measure of the acid/alkaline level of the water. It
is important to maintain the correct pH level as it effects
the action of other chemicals. The pH is measured on a
scale of 1 to 14. Seven is neutral, below seven is acidic,
and above seven is alkaline.
Incorrect pH levels can cause poor sanitiser efficiency,
eye and skin irritations, corrosion of metal fittings, cloudy
water and formation of scale on the pool walls and fittings.
The pH should always be above 7.0 (measured at room
temperature, not hot) to avoid possible corrosion of
equipment. However, it should not be higher than 7.8, as
this would reduce the efficiency of the sanitiser.
If the pH level needs to be increased, add soda ash; to
reduce the pH level, add dry acid. Wait for one hour and
test again.
The amount of disinfectant required depends on a number
of factors, including, water temperature, the frequency of
use and the number of people using the spa. It is most
important to always keep the sanitiser level at 2.00 to 3.00
ppm. In very hot water the sanitiser can be used up very
quickly, and should be checked regularly whilst the spa is
being used.
After heavy use of the spa or on a weekly basis, the water
should be shock dosed with sanitiser. Be sure to check
the level again before use. If the spa or hot tub is not
being used, add sanitiser every second day to prevent
contamination.
Recommended Levels
ItemLevel
Sanitiser (Chlorine)
2.0 – 3.0 ppm
Total Alkalinity
90 – 110 ppm
pH Level
7.4 – 7.6
It is important to note that if the right pH and sanitiser
levels are maintained, viruses and bacteria should not
survive in the water. In terms of general hygiene, it is
important to keep the filter and pump clean. Clean the filter
regularly and where ever possible always shower before
spa use.
17
PUMP
MAINTENANCE
The pumps in your spa are high
performance motors that require regular
checking. It is a requirement of your spa’s
warranty to check the pumps every four (4)
months for signs of leaking or corrosion.
Any sign of leaking or calcium build up at the bottom of the
pump between the plastic wet end and metal part of the
motor indicates that the seals of your pumps are worn and
need replacing. It is recommended that you contact your
local spa dealer to arrange a service of your pump before
the motor develops further problems.
Pump seal corrosion and wear is generally caused by
incorrect pH and alkalinity levels within the spa, or heavy
use /excessive dosage of sanitisers such as Chlorine or
Bromine. In order to avoid problems, please follow the water
chemistry instructions provided to you by your dealer.
BARREL
UNION
MAINTENANCE
Barrels unions are the connections
between the pumps and heater and the
plumbing of the spa. They are used to
enable easy removal of the spa equipment
in the event of servicing. However over
time with vibration from pumps and water
flow, and ageing of o-ring seals, it is
possible for the unions to work loose.
If they become loose, this can cause water
loss. It is important to check the tightness
of these unions periodically. The unions
are designed to be retightened by hand.
Rotate the locking nut clockwise to tighten.
Barrel union
NOTE: If you see water escaping from beneath your spa, the barrel unions should be the first thing you check. LEAKS FROM BARREL UNIONS ARE NOT COVERED BY THE SPA’S WARRANTY.
18
19
SHUTTING
DOWN
YOUR SPA
We firmly recommend that you NEVER
leave your spa empty for a period of 2
weeks or more, leaving your spa empty
can cause damage to the pumps, heater
element and shell. In most cases you are
better off turning the temperature of your
spa down to the minimum setting and
maintaining your PH & Alkalinity levels to
ensure they stay within recommended
readings.
If for some reason you need to empty your
spa for a period longer than 2 weeks we
recommend the following.
1. Empty your spa as per the drainage instructions in the owner’s manual.
2. Once the spa is empty, open the cabinet door to gain access to your controller and all pumps.
3.
Undo the barrel unions that connect the plumbing to the spa controller/ heater and pumps. Undoing these unions will allow any excess water in the pipework of the spa to be drained. Without following this process stagnant water will sit in the pipework
and cause damage to the seals in your pumps and your heater element and control sensors. (Damage related to incorrect water chemistry is not covered under the manufacturers warranty)
4. Once the spa pipework is empty of water, carefully re-connect and tighten the unions ensuring that the O-ring seal is seated correctly.
5. Hop into the spa and using a sponge and bucket, soak up any residual water remaining in the spa.
20
6.
At this point it is a good time to clean the water line on the spa if required, you can use a non-
abrasive cloth with some mild detergent. (Be sure to rinse any detergent from the spa before re-filling.)
7.
Our recommendation is to leave the cover off for a period of time to allow the shell to dry. (As per warning instructions on the shell, do not expose the acrylic shell to direct sunlight for extended periods of time)
8. Once you are satisfied that there is no excessive water in the spa and that it has been cleaned to avoid bacteria growth, you can place the cover on the spa for protection.
NOTE: It is recommended that you lift the cover from time to time over the course of the shut down to allow the spa to breathe.
21
TROUBLESHOTTING
Problem
Cause
Solution
Problem
Cause
Solution
No power to spa
1. Power cord unplugged
2. Isolator switch OFF
3. ELCB/RCD tripped
4. Faulty power point
1. Check plug connection
2. Check power switched ON
3. Reset breaker in meter box
4. Test another appliance from the power point
5. Contact spa dealer
Will not heat
1. Time not set correctly
2. Sleep timers or power save settings incorrect
1. Set the clock on control pad
2. Read control pad manual & check timer settings, consult spa dealer for assistance
3. Turn air blower off. Heating is inefficient when the blower is running
4. Check set temperature point and raise if needed
5. Fit hardcover to spa and ensure it is fitted correctly
5. Faulty control panel
Pumps run but no water
moving
1. Water level too low
2. Air lock in plumbing
3. Shut off valves closed
ELCB/RCD tripping
1. Drawing excess current
2. Spa not wired to dedicated circuit
3. Water on electrical components
4. Earth leakage problem
FLO & Prr Thermal Trip Errors
1. Low water level
2. Dirty filters
3. Air lock in pipe work
4. Fault with filtration pump
1. Add water to spa fill mark
2. Remove all filters and flush filter pipes with water from garden hose. If unsuccessful turn power off and slightly loosen barrel union to pump to release (bleed) air from pipes. Once air has been released and water is flowing retighten union
3. Check all valves are open
1. Heater load shed not configured, contact dealer
2. Spa pools must be supplied by a dedicated power circuit, not through an extension cord
3. Check water level, lower if overfilled. Power OFF, remove side panels and allow time for equipment bay to dry out
4. Turn power off and inspect power cable for damage. Contact electrician or spa dealer for advice
1. Refill spa if necessary
2. Clean, soak or replace filters
3. Bleed air from pipe work by loosening barrel unions
4. Contact dealer for service
NOTE:If possible, please take a photo and send to the service department or technician, to assist with the speed of the repair.
22
3. Air blower ON all the time
4. Thermostat turned down
5. Excessive heat loss
Water not clean
1. Filter clogged or due for replacement
2. Poor water chemistry
3. Filter duration not set high enough
1. Clean and soak filters, or replace Purezone micro filter
2. Check water balance and sanitiser levels. Refer to chemical instructions.
3. Increase daily filtration time in control pad setup menu
Water at base of the spa.
1.
2.
3.
Check for condensation from spa cover.
Wait to see if moisture dries out.
Remove cabinet panel under touch pad and inspect all barrel union connections as per page 19
in this manual.
You have identified a spa
leak.
1. If a barrel union connection is leaking, please tighten as per instructions.
2. If you have a leak from a jet body
or plumbing, please call the service department or your local dealer.
NOTE: Repairs are subject to warranty conditions, which have been provided with your spa. If you are unsure of your warranty coverage, please contact the service department or your local dealer.
23
HEAT PUMP
CONNECTION
INSTRUCTIONS
1. Turn off spa and close shut off valves to the circulation pump and controller. (Marked 1 on
the diagram).
2. Consult the heat pump installation guide to connect power and control wire.
3. Remove existing plumbing between circulation pump and controller. (Marked 2 on the diagram)
4. Fit the new 40mm circulation pump union supplied and point it in the direction where the heat pump will be located.
5. (IF PURCHASED)
Cut holes into the cabinet where the pipe will run into the heat pump, be sure cut the holes at a height that allows the pipes to remain even and supported on the cabinet.
6. Run 40mm pipe form the circulation pump to the inlet of the heat pump.
7. From the outlet of the heat pump, run 40mm pipe to the inlet of the controller using the supplied union to make new the connection.
NOTE:You must use PVC hard pipe on the outside of the spa, flexible pipe may only be used internally.
8. Open the shut off valves. (Marked 1 on the diagram).
9. Undo the top outlet on the heat pump to bleed air out of the system.
10. Close it once water comes out and then switch on the spa.
11. Make sure the circulation pump is flowing and is free of any air locks.
12.Depending on the installation, purezone filters may create a flow error, we suggest replacing this filter with a standard paper version.
Parts supplied:
•1x circulation pump barrel union.
•1x 40mm 90 Degree Street elbow.
•1x barrel union.
Tools and parts required:
•40mm or larger hole saw
•PVC Pipe Glue
•Hacksaw
•40mm hard pipe
(The amount of pipe or fittings required will
depend on your installation)
Spa Pool
2
NOTE:This document is to be considered a guide only. Before installing your heat pump, please consult the heat pump installation and user manual in order to ensure that your heat pump has been installed to the manufacturers recommendations. Failure to install your heat pump correctly, could void your warranty.
24
Control Box
1
Heat Pump
NOTE:
Please refer to heat
pump installation and
user manual for air
flow requirements
when positioning
your heat pump.
Existing Plumbing
1
Valve
Circulation Pump
Heater
The heat pump must be installed at
least 1 metre from the spa pool.
The heat pump must not be
further than 2.5 metres from
the circulation pump.
NOTE: The heat pump must be installed at the same approximate level as the circulation pump.
25
25/02/16 V1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement