Pioneer VSX-S300-S Owner Manual

Add to my manuals
36 Pages

advertisement

Pioneer VSX-S300-S Owner Manual | Manualzz

VSX-S300_SYXCN_En.book 1 ページ 2011年4月8日 金曜日 午後8時10分

VSX-S300

-K

AUDIO/VIDEO MULTI-CHANNEL RECEIVER

Discover the benefits of registering your product online at

http://www.pioneer.co.uk

(or http://www.pioneer.eu).

Operating Instructions

VSX-S300_SYXCN_En.book 2 ページ 2011年4月8日 金曜日 午後8時10分

2

En

IMPORTANT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

D3-4-2-1-1_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation

(at least 10 cm at top, 5 cm at rear, and 5 cm at each side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

D3-4-2-1-7b*_A1_En

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.

IMPORTANT: THE MOULDED PLUG

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 10 amp fuse is fitted in this plug.

Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.

If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Blue : Neutral Brown : Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows;

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

D3-4-2-1-2-2*_A2_En

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

D3-4-2-1-7c*_A1_En

VSX-S300_SYXCN_En.book 3 ページ 2011年4月8日 金曜日 午後8時10分

Information for users on collection and disposal of old equipment and used batteries

Symbol for equipment

Symbol examples for batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation.

By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

Pb

K058a_A1_En

WARNING

This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.

D3-4-2-1-3_A1_En

WARNING

Before plugging in for the first time, read the following section carefully.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230 V or 120 V) written on the rear panel.

D3-4-2-1-4*_A1_En

This product is for general household purposes. Any failure due to use for other than household purposes

(such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.

K041_A1_En

If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal.

The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-1a_A1_En

CAUTION

The

STANDBY/ON switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the

AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-2a*_A1_En

3

En

VSX-S300_SYXCN_En.book 4 ページ 2011年4月8日 金曜日 午後8時10分

4

En

Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.

Contents

Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Checking what’s in the box

. . . . . . . . . . . . . . . . . . . . . . . . 5

Installing the receiver

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Flow of settings on the receiver. . . . . . . . . . . . . . 5

01 Controls and displays

Front panel

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Display

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Remote control

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Loading the batteries

. . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Operating range of remote control

. . . . . . . . . . . . . . . . . 8

02 Connecting your equipment

Determining the speakers’ application

. . . . . . . . . . . . . . . 9

Some tips for improving sound quality

. . . . . . . . . . . . . . 9

Connecting the speakers

. . . . . . . . . . . . . . . . . . . . . . . . . 10

Connect the surround back or front height speakers

. . . 11

Switching the speaker terminal

. . . . . . . . . . . . . . . . . . 11

Making cable connections

. . . . . . . . . . . . . . . . . . . . . . . 11

HDMI cables

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

About HDMI

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Analog audio cables

. . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Digital audio cables

. . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Standard RCA video cables

. . . . . . . . . . . . . . . . . . . . . 12

About video outputs connection

. . . . . . . . . . . . . . . . . . . 12

Connecting a TV and playback components

. . . . . . . . . . 13

Connecting using HDMI

. . . . . . . . . . . . . . . . . . . . . . . 13

Connecting your component with no HDMI terminal

. . 14

Connecting optional Bluetooth

®

ADAPTER

. . . . . . . . . . . 14

Connecting antennas

. . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Using external antennas

. . . . . . . . . . . . . . . . . . . . . . . 15

Connecting to the front panel audio mini jack

. . . . . . . . . 15

Plugging in the receiver

. . . . . . . . . . . . . . . . . . . . . . . . . 15

03 Basic Setup

Canceling the Auto Power Down

. . . . . . . . . . . . . . . . . . . 16

Canceling the demo display

. . . . . . . . . . . . . . . . . . . . . . 16

Automatically setting up for surround sound (MCACC)

. . 16

Other problems when using the Auto MCACC setup

. . 17

04 Basic playback

Playing a source

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Bluetooth

®

ADAPTER for Wireless Enjoyment of

Music

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Wireless music play

. . . . . . . . . . . . . . . . . . . . . . . . . . 19

Pairing the Bluetooth ADAPTER and Bluetooth wireless technology device

. . . . . . . . . . . . . . . . . . . . . 19

Listening to Music Contents of Bluetooth wireless technology device with Your System

. . . . . . . . . . . . . . 19

Listening to the radio

. . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Improving FM sound

. . . . . . . . . . . . . . . . . . . . . . . . . . 20

Saving station presets

. . . . . . . . . . . . . . . . . . . . . . . . . 20

Listening to station presets

. . . . . . . . . . . . . . . . . . . . . 20

Naming preset stations

. . . . . . . . . . . . . . . . . . . . . . . . 20

An introduction to RDS

. . . . . . . . . . . . . . . . . . . . . . . . . 21

Searching for RDS programs

. . . . . . . . . . . . . . . . . . . 21

Displaying RDS information

. . . . . . . . . . . . . . . . . . . . 21

05 Listening to your system

Choosing the listening mode

. . . . . . . . . . . . . . . . . . . . . 22

Auto playback

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Listening in surround sound

. . . . . . . . . . . . . . . . . . . . 22

Using the Advanced surround

. . . . . . . . . . . . . . . . . . 23

Using Stream Direct

. . . . . . . . . . . . . . . . . . . . . . . . . . 23

Using the Ecology mode

. . . . . . . . . . . . . . . . . . . . . . . . . 23

Using the Sound Retriever

. . . . . . . . . . . . . . . . . . . . . . . 24

Setting the Up Mix function

. . . . . . . . . . . . . . . . . . . . . . 24

Setting the Audio options

. . . . . . . . . . . . . . . . . . . . . . . . 24

06 The Home Menu

Using the Home Menu

. . . . . . . . . . . . . . . . . . . . . . . . . . 27

Manual speaker setup

. . . . . . . . . . . . . . . . . . . . . . . . . . 27

Speaker System

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Speaker Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

X.OVER

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Channel Level

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Speaker Distance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

The Pre Out Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

The Input Assign menu

. . . . . . . . . . . . . . . . . . . . . . . . . . 30

The Auto Power Down menu

. . . . . . . . . . . . . . . . . . . . . 30

The FL Demo Mode menu

. . . . . . . . . . . . . . . . . . . . . . . . 30

07 Control with HDMI function

Making Control with HDMI connections

. . . . . . . . . . . . 31

HDMI Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Before using synchronization

. . . . . . . . . . . . . . . . . . . . . 32

About synchronized operations

. . . . . . . . . . . . . . . . . . . 32

About connections with a product of a different brand that supports the Control with HDMI function

. . . . . . 32

Cautions on the Control with HDMI function

. . . . . . . . . 32

08 Additional information

Troubleshooting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

General

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

HDMI

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Important information regarding the HDMI connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Resetting the main unit

. . . . . . . . . . . . . . . . . . . . . . . . . 35

Cleaning the unit

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

VSX-S300_SYXCN_En.book 5 ページ 2011年4月8日 金曜日 午後8時10分

Before you start

Checking what’s in the box

Please check that you’ve received the following supplied accessories:

• Setup microphone

• Remote control

• AAA size IEC R03 dry cell batteries (to confirm system operation) x2

• AM loop antenna

• FM wire antenna

• Power cord

• Warranty card

• Quick start guide

• Safety Brochure

• These operating instructions (CD-ROM)

Installing the receiver

• When installing this unit, make sure to put it on a level and stable surface.

Don’t install it on the following places:

– on a color TV (the screen may distort)

– near a cassette deck (or close to a device that gives off a magnetic field). This may interfere with the sound.

– in direct sunlight

– in damp or wet areas

– in extremely hot or cold areas

– in places where there is vibration or other movement

– in places that are very dusty

– in places that have hot fumes or oils (such as a kitchen)

Flow of settings on the receiver

The unit is a full-fledged AV receiver equipped with an abundance of functions and terminals. It can be used easily after following the procedure below to make the connections and settings.

The colors of the steps indicate the following:

Required setting item

Setting to be made as necessary

1

Connecting the speakers

Where you place the speakers will have a big effect on the sound.

• Determining the speakers’ application (page 9)

• Connecting the speakers (page 10)

2

Connecting the components

For surround sound, you’ll want to hook up using a digital connection from the Blu-ray Disc/DVD player to the receiver.

• About video outputs connection (page 12)

• Connecting a TV and playback components (page 13)

• Connecting antennas (page 14)

• Plugging in the receiver (page 15)

3

Power On

Make sure you’ve set the video input on your TV to this receiver. Check the manual that came with the TV if you don’t know how to do this.

4

Speaker System (page 27)

(When connecting the B Speakers.)

The Pre Out Setting (page 30)

(When connecting the front height speakers.)

The Input Assign menu (page 30)

(When using connections other than the recommended connections.)

Using the Audio Return Channel function (page 31)

(When the connected TV supports the HDMI Audio

Return Channel function.)

5

Use the on-screen automatic MCACC setup to set up your system

• Automatically setting up for surround sound (MCACC)

(page 16)

6

Playing a source (page 18)

• Choosing the listening mode (page 22)

7

Adjusting the sound as desired

• Using the Sound Retriever (page 24)

• Setting the Up Mix function (page 24)

• Setting the Audio options (page 24)

• Manual speaker setup (page 27)

5

En

VSX-S300_SYXCN_En.book 6 ページ 2011年4月8日 金曜日 午後8時10分

Controls and displays

Chapter 1:

Controls and displays

Front panel

STANDBY / ON

PHONES

PORTABLE /

MCACC SETUP MIC

MCACC

HDMI

INPUT SELECTOR

AUDIO/ VIDEO MULTI- CHANNEL RECEIVER VSX-S300

SOUND

RETRIEVER

MASTER

VOLUME

11 12 13 14 13 15 16

6

En

1 2 3 4 5

1

STANDBY/ON

2 PHONES jack

Use to connect headphones. When the headphones are connected, there is no sound output from the speakers. The listening mode when the sound is heard from the headphone can be selected only from PHONES SURR, STEREO or

STEREO ALC mode (S.R AIR mode can be also selected with

ADAPTER input).

3 PORTABLE/MCACC SETUP MIC jack

Use to connect an auxiliary component using a stereo minijack cable (page 15) or connect a microphone when performing Auto MCACC setup (page 16).

4 Remote sensor

Receives the signals from the remote control (see Operating

range of remote control on page 8).

5 Character display

See Display on page 6.

6 MCACC indicator

Lights when Acoustic Calibration EQ (page 25) is on

(Acoustic Calibration EQ is automatically set to on after the

Auto MCACC setup (page 16)).

7 HDMI indicator

Blinks when connecting an HDMI-equipped component; lights when the component is connected (page 13).

6 7 8 9 10

8 INPUT SELECTOR

Selects an input source (page 18).

9 SOUND RETRIEVER

Press to restore CD quality sound to compressed audio sources (page 24).

10 MASTER VOLUME dial

Display

11 Dolby Digital indicators

2 D – Lights when a Dolby Digital encoded signal is detected.

2TrueHD – Lights when a source with Dolby TrueHD encoded audio signals is detected.

2 D+ – Lights when a source with Dolby Digital Plus encoded audio signals is detected.

EX – Lights to indicate Dolby Digital EX decoding.

PLII(x/z) – Lights to indicate 2 Pro Logic II/2 Pro Logic

IIx or

2 Pro Logic IIz decoding (see Listening in surround

sound on page 22 for more on this).

12 DTS indicators

DTS – Lights when a source with DTS encoded audio signals is detected.

HD – Lights when a source with DTS-EXPRESS or DTS-

HD encoded audio signals is detected.

ES – Lights to indicate DTS-ES decoding.

96/24 – Lights when a source with DTS 96/24 encoded audio signals is detected.

13 Listening mode indicators

AT – Lights when the Auto Surround feature is switched on (page 22).

DIR – Lights when the DIRECT or PURE DIR mode is switched on (page 23).

14 Audio signal indicators

D – Lights when a digital audio input is selected. Blinks when a digital audio input is selected and selected audio input is not provided.

HDMI – Lights when an HDMI input is selected. Blinks when an HDMI input is selected and selected HDMI signal is not provided.

15 Character display

Displays various system information, the preset number of the tuner or the input signal type, etc.

16 Sleep timer ( ) indicator

Lights when the receiver is in sleep mode (page 7).

VSX-S300_SYXCN_En.book 7 ページ 2011年4月8日 金曜日 午後8時10分

Controls and displays

Remote control

1

2

STANDBY/ON

D AUX A AUX

ECO

S.RTRV

iPod USB NETWORK ADAPTER

AUTO /

DIRECT

TUNER BD DVD

ALC /

STANDARD

CD STB GAME

ADV

SURR

RECEIVER TV PORTABLE

SOUND

WING

3

SLEEP SP-AB

AUDIO

DIMMER

DISP

STATUS

4

TOP

MENU

MENU

TOOLS VOL

5

ENTER

6

iPod

CTRL

HOME MENU

PTY

RETURN

BAND MUTE

7

PRESET TUNE

8

9

10

11

12

RECEIVER

The following buttons are not used with this receiver:

-

iPod USB, NETWORK, , ,

1

STANDBY/ON

Switches the receiver between standby and on.

2 Input function buttons

Use to select the input source to this receiver (page 18). This will enable you to control other Pioneer components with the remote control.

• Switch to one of the underlined devices to use the remote control to operate that device. As for operating other devices, the remote control codes for the Pioneer products are preset. The settings cannot be changed.

3

RECEIVER

Switches the remote to control the receiver. Also use this button to set up surround sound (page 27) or Audio parameters (page 24).

4 Receiver control buttons

Press

RECEIVER

first to access:

SLEEP – Press to change the amount of time before the receiver switches into standby (

30 min – 60 min – 90 min

– Off). You can check the remaining sleep time at any time by pressing

SLEEP once.

SP-AB – See Switching the speaker terminal on page 11.

DIMMER – Dims or brightens the display. The brightness can be controlled in four steps.

STATUS – Switches the display of this unit.

The Pre Out setting and Up Mix function settings can be checked depending on the input selected.

Press TUNER first to access:

DISP – Press to display the preset name (page 20).

Press BD or DVD first to access:

AUDIO – Press to change the audio stream/channel of

Blu-ray Disc/DVD.

DISP – Press to display information of a Blu-ray Disc/DVD.

5 Receiver and component control buttons

The following button controls can be accessed after you have selected the corresponding input function button ( BD, DVD, etc.).

Press

RECEIVER

first to access:

TOOLS – Use to access the Audio options (page 24).

HOME MENU – Press to access the Home Menu

(page 27).

RETURN – Confirm and exit the current menu screen.

Press TUNER first to access:

TOOLS – Memorizes stations for recall, also used to change the name (page 20).

Press BD or DVD first to access:

TOP MENU – Displays the disc ‘top’ menu of a Blu-ray

Disc/DVD.

HOME MENU – Displays the HOME MENU screen.

RETURN – Confirm and exit the current menu screen.

MENU – Displays the TOOLS menu of Blu-ray Disc player.

6

///, ENTER

Use the arrow buttons when setting up your surround sound system (page 27). Also used to control Blu-ray Disc/DVD menus/options.

7 Component control buttons

The main buttons (

, , etc.) are used to control a component after you have selected it using the input function buttons.

The controls above these buttons can be accessed after you have selected the corresponding input function button ( BD,

DVD and CD). These buttons also function as described below.

Press TUNER first to access:

PTY – Use to search for RDS program types (page 21).

BAND – Switches between AM, FM ST (stereo) and FM

MONO radio bands (page 20).

TUNE +/– – Use to find radio frequencies.

PRESET +/– – Use to select preset radio stations.

8 ECO

Press to select Ecology mode (page 23).

7

En

VSX-S300_SYXCN_En.book 8 ページ 2011年4月8日 金曜日 午後8時10分

8

En

Controls and displays

9 S.RTRV

Press to restore CD quality sound to compressed audio sources (page 24).

10 Listening mode buttons

AUTO/DIRECT – Switches between Auto surround mode

(page 22) and Stream Direct playback (page 23).

ALC/STANDARD – Press for standard decoding and to switch between the modes of

2 Pro Logic II, 2 Pro

Logic IIx,

2 Pro Logic IIz and NEO:6, and the Auto level control stereo mode (page 22).

ADV SURR – Switches between the various surround modes (page 23).

SOUND WING – Press to select Sound wing mode

(page 22).

11 VOL +/–

Use to set the listening volume.

12 MUTE

Mutes/unmutes the sound.

Loading the batteries

When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area.

-

Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or performance of batteries.

Operating range of remote control

The remote control may not work properly if:

• There are obstacles between the remote control and the receiver’s remote sensor.

• Direct sunlight or fluorescent light is shining onto the remote sensor.

• The receiver is located near a device that is emitting infrared rays.

• The receiver is operated simultaneously with another infrared remote control unit.

30°

30°

7 m

The batteries included with the unit are to check initial operations; they may not last over a long period. We recommend using alkaline batteries that have a longer life.

CAUTION

• Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions:

-

Never use new and old batteries together.

Insert the plus and minus sides of the batteries properly according to the marks in the battery case.

-

Batteries with the same shape may have different voltages. Do not use different batteries together.

VSX-S300_SYXCN_En.book 9 ページ 2011年4月8日 金曜日 午後8時10分

Connecting your equipment

Chapter 2:

Connecting your equipment

Determining the speakers’ application

By connecting the left and right front speakers ( L/R), the center speaker ( C), the left and right surround speakers (SL/

SR), the left and right surround back speakers (SBL/SBR) (or the left and right front height speakers ( FHL/FHR)), and the subwoofer (

SW), a surround sound system up to 7.1 channel can be enjoyed.

The 5.1 channel surround system is the most commonlyused in home theaters. To achieve the best possible surround sound, install your speakers as shown below.

5.1 channel surround system:

6.1 channel surround

(Surround back) system:

L

C

SL

SW

R

SR

L

C

SW

R

SL

SB

SR

7.1 channel surround

(Surround back) system:

L

R

C

SL

SBL

SW

SR

SBR

7.1 channel surround

(Front height) system:

FHL

FHR

R

L

SW

C

SR

SL

Important

To connect the surround back or front height

speakers, an additional amplifier is required. Connect the additional amplifier to the

PRE OUT SURR BACK/

FRONT HEIGHT outputs of this unit and connect the surround back or front height speakers to the additional amplifier (see Connect the surround back or front height

speakers on page 11).

Another way, you can use the speakers connected to the B speaker terminals to listen to stereo playback in another room. See Switching the speaker terminal on page 11 for the listening options with this setup.

You will not be able to connect the B speakers if you

connect the surround speakers in the main zone.

When using the B speakers, main zone sound will only be output from the front speakers, the center speaker and the subwoofer. (No sound is output from the surround and surround back speakers.)

• Speaker B does not allow for subwoofer connection.

Please use full-range speakers.

Where you put your speakers in the room has a big effect on the quality of the sound. The following guidelines should help you to get the best sound from your system.

• It is best to angle the speakers towards the listening position. The angle depends on the size of the room. Use less of an angle for bigger rooms.

• Refer to the chart below for placement of speakers you intend to connect.

FHL

L

C

SW

FHR

R

30 30

L

R

Speaker B

Main zone

Some tips for improving sound quality

Important

• Speakers such as S-HV500-LR and S-HV600B may have specific installation methods. For more details, refer to the operating instructions supplied with speaker.

120 120

SL

60

SR

SBL SB SBR

Place the surround speakers at 120º from the center. If you, (1) use the surround back speaker, and, (2) don’t use the front height speakers, we recommend placing the surround speaker right beside you.

-

If you intend to connect only one surround back speakers, place it directly behind you.

-

If the surround speakers cannot be set directly to the side of the listening position with a 7.1-channel system, the surround effect can be enhanced by turning off the

Up Mix function (see Setting the Up Mix function on page 24).

• For the best stereo effect, place the front speakers 2 m to

3 m apart, at equal distance from the TV.

• If you’re using a center speaker, place the front speakers at a wider angle. If not, place them at a narrower angle.

• Place the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen.

Also, make sure the center speaker does not cross the line formed by the leading edge of the front left and right speakers.

9

En

VSX-S300_SYXCN_En.book 10 ページ 2011年4月8日 金曜日 午後8時10分

Connecting your equipment

10

En

• Surround and surround back speakers should be positioned 60 cm to 90 cm higher than your ears and titled slight downward. Make sure the speakers don’t face each other. For

DVD-Audio, the speakers should be more directly behind the listener than for home theater playback.

• Try not to place the surround speakers farther away from the listening position than the front and center speakers. Doing so can weaken the surround sound effect.

• Place the left and right front height speakers at least one meter directly above the left and right front speakers.

• If you’re going to place speakers around your CRT TV, use shielded speakers or place the speakers at a sufficient distance from your CRT TV.

• The subwoofer can be placed on the floor. Ideally, the other speakers should be at about ear-level when you’re listening to them. Putting the speakers on the floor (except the subwoofer), or mounting them very high on a wall is not recommended.

• When not connecting a subwoofer, connect speakers with low frequency reproduction capabilities to the front channel. (The subwoofer’s low frequency component is played from the front speakers, so the speakers could be damaged.)

After connecting, be sure to conduct the Auto MCACC (speaker environment setting) procedure.

See Automatically setting up for surround sound (MCACC) on page 16.

CAUTION

• Make sure that all speakers are securely installed. This not only improves sound quality, but also reduces the risk of damage or injury resulting from speakers being knocked over or falling in the event of external shocks such as earthquakes.

Connecting the speakers

The receiver will work with just two stereo speakers (the front speakers in the diagram) but using at least three speakers is recommended, and a complete setup is best for surround sound.

Make sure you connect the speaker on the right to the right ( R) terminal and the speaker on the left to the left (

L) terminal. Also make sure the positive and negative (+/) terminals on the receiver match those on the speakers.

You can use speakers with a normal impedance between 4

Ω and 16 Ω.

Important

• SPEAKERS SUBWOOFER terminals are Pioneer’s passive subwoofer S-SLW500 connection terminals. If using another model of subwoofer, be sure to use a model with built-in amp and connect to the PREOUT SUBWOOFER terminal.

• Please connect either passive or powered subwoofers, as connecting both makes it impossible to achieve the correct sound effect.

Be sure to complete all connections before connecting this unit to the AC power source.

Front right

Right

Right

Center

R IN GAME IN

OUT COAXIAL

OPTICAL

A

R

FRONT

L

VIDEO

ASSIGNABLE

(ANALOG

AUX)

IN

ANALOG

AUX

CD IN

SURR BACK/

FRONT HEIGHT

TV IN DIGITAL AUX IN

AUDIO

L

(Single)

SPEAKERS

CENTER

SUB

WOOFER SURROUND /

R L

B

MONITOR

OUT

IN

R

SUBWOOFER

PRE OUT

R ANALOG

AUDIO IN

L

SPEAKER

R

Surround back or front height channel amplifier

SPEAKER

L

Left

Left

Front left

Passive subwoofer

(S-SLW500)

LINE LEVEL

INPUT

Powered

Subwoofer

Surround speakers or B-Speakers

Surround back or front height speakers

VSX-S300_SYXCN_En.book 11 ページ 2011年4月8日 金曜日 午後8時10分

Connecting your equipment

Bare wire connections

Front speaker terminals:

1

Twist exposed wire strands together.

2

Loosen terminal and insert exposed wire.

3

Tighten terminal.

1

10 mm

2 3

Other speaker terminals:

1

Twist exposed wire strands together.

2

Push open the tabs and insert exposed wire.

3

Release the tabs.

1

10 mm

2 3

CAUTION

• These speaker terminals carry

HAZARDOUS LIVE

voltage. To prevent the risk of electric shock when connecting or disconnecting the speaker cables, disconnect the power cord before touching any uninsulated parts.

• Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker terminal. If any of the bare speaker wire touches the back panel it may cause the power to cut off as a safety measure.

• Do not allow the speaker cable core to come into contact with the receiver body.

SP:B ON – Sound is output from the two speakers connected to the B-speaker terminals (only stereo playback is possible).

SP:A+B ON – Sound is output from the A-speaker terminals, the two speakers in the B-speaker terminals, and the subwoofer. Multichannel sources are downmixed only when the

STEREO or STEREO ALC mode is selected for stereo output from A- and B-speaker terminals.

SP: OFF – No sound is output from the speakers.

Note

• Only SP:A ON and SP: OFF are available when the

Speaker System setting is set to Normal (see Speaker

System on page 27).

• The subwoofer output depends on the settings you made in Speaker Setting on page 28. However, if

SP:B ON is selected above, no sound is heard from the subwoofer

(the LFE channel is not downmixed).

• All speaker terminals are switched off when headphones are connected.

-

If the speaker cable core comes into contact with any metal portion of the receiver's body, it may damage the speakers and cause smoke and fire.

Insert speaker cables securely into the terminals and check that the cable does not come out of easily.

Connect the surround back or front height speakers

Connect the

PRE OUT SURR BACK/FRONT HEIGHT outputs of the unit and additional amplifier to add a surround back or front height speaker.

• The Pre Out setting must be set if the above connections are performed. Select Surr.Back if the surround back speaker is connected and Height if the front height speaker is connected (If neither the surround back speaker nor the front height speaker is connected, either setting will suffice) (see The Pre Out Setting on page 30).

• You can use the additional amplifier on the surround back channel pre-outs for a single speaker as well. In this case plug the amplifier into the left ( L (Single)) terminal only.

Switching the speaker terminal

Three speaker system settings are possible.

Use SP-AB button to select a speaker terminal setting.

Press repeatedly to choose a speaker terminal option:

SP:A ON – Sound is output from the speakers connected to the A-speaker terminals and

PRE OUT SURR BACK/

FRONT HEIGHT (multichannel playback is possible).

Making cable connections

Make sure not to bend the cables over the top of this unit (as shown in the illustration). If this happens, the magnetic field produced by the transformers in this unit may cause a humming noise from the speakers.

Important

• Before making or changing connections, switch off the power and disconnect the power cord from the AC outlet.

• Before unplugging the power cord, switch the power into standby.

HDMI cables

Both video and sound signals can be transmitted simultaneously with one cable. If connecting the player and the

TV via this receiver, for both connections, use HDMI cables.

HDMI

11

En

VSX-S300_SYXCN_En.book 12 ページ 2011年4月8日 金曜日 午後8時10分

Connecting your equipment

12

En

Be careful to connect the terminal in the proper direction.

Note

• Set the HDMI parameter in Setting the Audio options on page 24 to

THRU (THROUGH), if you want to hear HDMI audio output from your TV (no sound will be heard from this receiver).

• If the video signal does not appear on your TV, try adjusting the resolution settings on your component or display. Note that some components (such as video game units) have resolutions that may not be displayed. In this case, use a (analog) composite connection.

• When the video signal from the HDMI is 480i, 480p, 576i or 576p, Multi Ch PCM sound and HD sound cannot be received.

About HDMI

The HDMI connection transfers uncompressed digital video, as well as almost every kind of digital audio that the connected component is compatible with, including DVD-

Video, DVD-Audio, SACD, Dolby Digital Plus, Dolby TrueHD,

DTS-HD Master Audio (see below for limitations), Video CD/

Super VCD and CD.

This receiver incorporates High-Definition Multimedia

Interface (HDMI

®

) technology.

This receiver supports the functions described below through

HDMI connections.

• Digital transfer of uncompressed video (contents protected by HDCP (1080p/24, 1080p/60, etc.))

• 3D signal transfer

• Deep Color signal transfer

• x.v.Color signal transfer

• Audio Return Channel

• Input of multi-channel linear PCM digital audio signals

(192 kHz or less) for up to 8 channels

• Input of the following digital audio formats:

– Dolby Digital, Dolby Digital Plus, DTS, High bitrate audio (Dolby TrueHD, DTS-HD Master Audio), DVD-

Audio, CD, SACD (DSD 2 ch only), Video CD, Super VCD

• Synchronized operation with components using the

Control with HDMI function (see Control with HDMI

function on page 31)

Note

• Use a High Speed HDMI

® a High Speed HDMI

®

cable. If HDMI cable other than

cable is used, it may not work properly.

• When an HDMI cable with a built-in equalizer is connected, it may not operate properly.

• 3D, Deep Color, x.v.Color signal transfer and Audio

Return Channel are only possible when connected to a compatible component.

• HDMI format digital audio transmissions require a longer time to be recognized. Due to this, interruption in the audio may occur when switching between audio formats or beginning playback.

• Turning on/off the device connected to this unit’s HDMI

OUT terminal during playback, or disconnecting/ connecting the HDMI cable during playback, may cause noise or interrupted audio.

HDMI, the HDMI Logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of HDMI

Licensing, LLC in the United States and other countries.

“x.v.Color” and

Corporation.

are trademarks of Sony

Analog audio cables

Use stereo RCA phono cables to connect analog audio components. These cables are typically red and white, and you should connect the red plugs to R (right) terminals and white plugs to L (left) terminals.

AUDIO

White (Left)

L

Digital audio cables

Commercially available coaxial digital audio cables or optical cables should be used to connect digital components to this receiver.

COAXIAL

Coaxial digital audio cable

IN

OPTICAL

IN

Optical cable

Note

• When connecting optical cables, be careful when inserting the plug not to damage the shutter protecting the optical socket.

• When storing optical cable, coil loosely. The cable may be damaged if bent around sharp corners.

• You can also use a standard RCA video cable for coaxial digital connections.

Standard RCA video cables

These cables are the most common type of video connection and are used to connect to the composite video terminals.

The yellow plugs distinguish them from cables for audio.

VIDEO

Yellow

R

Red (Right)

About video outputs connection

This receiver is not loaded with a video converter. When you use HDMI cables for connecting to the input device, the same cables should be used for connecting to the TV.

The signals input from the analog (composite) video inputs of this unit will not be output from the HDMI OUT.

VSX-S300_SYXCN_En.book 13 ページ 2011年4月8日 金曜日 午後8時10分

Connecting your equipment

Connecting a TV and playback components

Connecting using HDMI

If you have an HDMI or DVI (with HDCP) equipped component (Blu-ray Disc player, etc.), you can connect it to this receiver using a commercially available HDMI cable.

If the TV and playback components support the Control with HDMI feature, the convenient

Control with HDMI functions can be used (see Control with HDMI function on page 31).

• The following connection/setting is required to listen to the sound of the TV over this receiver.

If the TV does not support the HDMI Audio Return Channel function, connect the receiver and TV with audio cables (as shown).

If the TV supports the HDMI Audio Return Channel function, the sound of the TV is input to the receiver via the HDMI terminal, so there is no need to connect an audio cable. In this case, set ARC at HDMI Setup to ON (see HDMI Setup on page 31).

Important

• If the receiver is connected to a TV using an HDMI cable, the on-screen display (OSD) will not be displayed. Be sure to use a standard RCA analog video cable to connect. In this case, switch the TV input to analog to see the OSD screen (for setup, etc.) on the TV.

• When the Control with HDMI function is ON and the receiver is connected to a compatible

TV with an HDMI cable, and you switch the input of the TV to composite, the input of the receiver may automatically switch to TV. If this happens, switch the receiver’s input back to the original input, or turn OFF the Control with HDMI function (see HDMI Setup on page 31).

Set-top box

HDMI/DVI-compatible components

DVD player,

HDD/DVD recorder

Blu-ray Disc player,

Blu-ray Disc recorder

Game console

HDMI OUT HDMI OUT HDMI OUT

FM

UNBAL

75

AM LOOP

ANTENNA

STB IN DVD/DVR IN BD/BDR IN GAME IN

HDMI

OUT COAXIAL

OPTICAL

VIDEO

ASSIGNABLE

(

ANALOG

AUX )

IN

ANALOG

AUX

CD IN

SURR BACK/

FRONT HEIGHT

TV IN DIGITAL AUX IN

AUDIO

L

(Single)

( OUTPUT 5 V

0.1 A MAX

)

ADAPTER PORT

MONITOR

OUT

IN

R

SUBWOOFER

PRE OUT

This connection is necessary in order to see the OSD of the unit on the TV.

VIDEO IN

HDMI IN

OPTICAL

DIGITAL AUDIO OUT

HDMI/DVI-compatible TV

If the TV does not support the HDMI Audio Return

Channel function, this connection is required to listen to the TV sound over the receiver.

13

En

VSX-S300_SYXCN_En.book 14 ページ 2011年4月8日 金曜日 午後8時10分

Connecting your equipment

14

En

Connecting your component with no HDMI terminal

This diagram shows connections of a TV and DVD player (or other playback component) with no HDMI terminal to the receiver.

Note

• When using a digital cable for DVD player audio input, change the Composite Input setting to CD (Coaxial) or

DIGITAL AUX (Optical) via the Input Assign menu (see

The Input Assign menu on page 30).

DVD player

Select one

ANALOG

AUDIO OUT

L R

DIGITAL AUDIO OUT

COAXIAL OPTICAL

Connecting optional Bluetooth

®

ADAPTER

When the Bluetooth ADAPTER (Pioneer Model No. AS-BT100 or AS-BT200) is connected to this unit, a product equipped with Bluetooth wireless technology (portable cell phone, digital music player, etc.) can be used to listen to music wirelessly.

Connect a

Bluetooth

ADAPTER to the ADAPTER PORT terminal on the rear panel.

• For instructions on playing the Bluetooth wireless technology device, see Pairing the Bluetooth ADAPTER

and Bluetooth wireless technology device on page 19.

Important

• Do not move the receiver with the Bluetooth ADAPTER connected. Doing so could cause damage or faulty contact.

VIDEO OUT

STB IN DVD/DVR IN BD/BDR IN GAME IN

Connecting antennas

Connect the AM loop antenna and the FM wire antenna as shown below. To improve reception and sound quality, connect external antennas (see Using external antennas below). fig. a fig. b

VIDEO IN

DVR IN BD/BDR IN GAME IN

HDMI

OUT COAXIAL

OPTICAL

VIDEO

ASSIGNABLE

( ANALOG

AUX

)

IN

ANALOG

AUX

CD IN

SURR BACK/

FRONT HEIGHT

TV IN DIGITAL AUX IN

AUDIO

L

(Single)

PUT 5 V

A MAX )

PTER PORT

MONITOR

OUT

IN

R

SUBWOOFER

PRE OUT

TV

OPTICAL

DIGITAL AUDIO OUT

This connection is required in order to listen to the sound of the TV over the receiver.

FM

UNBAL

75

AM LOOP

ANTENNA

Bluetooth

®

ADAPTER

HDMI

VIDEO

ASSIGNABLE

( ANALOG

AUX )

IN

A

(

OUTPUT 5 V

0.1 A MAX

)

ADAPTER PORT

MONITOR

OUT

1

4

FM

UNBAL

75

AM LOOP

ANTENNA

2

3

1

Push open the tabs, then insert one wire fully into each terminal, then release the tabs to secure the AM antenna wires.

2

Fix the AM loop antenna to the attached stand.

To fix the stand to the antenna, bend in the direction indicated by the arrow (fig. a) then clip the loop onto the stand (fig. b).

3

Place the AM antenna on a flat surface and in a direction giving the best reception.

4

Connect the FM wire antenna into the FM antenna socket.

For best results, extend the FM antenna fully and fix to a wall or door frame. Don’t drape loosely or leave coiled up.

VSX-S300_SYXCN_En.book 15 ページ 2011年4月8日 金曜日 午後8時10分

Connecting your equipment

Using external antennas

To improve FM reception

Use a PAL connector (not supplied) to connect an external

FM antenna.

One-touch

PAL connector

FM

UNBAL

75

ANTENNA

75

Ω coaxial cable

To improve AM reception

Connect a 5 m to 6 m length of vinyl-coated wire to the AM antenna terminal without disconnecting the supplied AM loop antenna.

For the best possible reception, suspend horizontally outdoors.

Indoor antenna

(vinyl-coated wire)

Outdoor antenna

AM LOOP

ANTENNA

5 m to 6 m

Connecting to the front panel audio mini jack

Front audio connections are accessed via the front panel using the PORTABLE button on the remote control. Use a stereo mini-jack cable to connect a digital audio player, etc.

STANDBY / ON

This receiver

PHONES

PORTABLE /

MCACC SETUP MIC

AUDIO OUT

Digital audio player, etc.

Plugging in the receiver

Only plug in after you have connected all your components to this receiver, including the speakers.

CAUTION

• Handle the power cord by the plug part. Do not pull out the plug by tugging the cord, and never touch the power cord when your hands are wet, as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, or other object on the power cord or pinch the cord in any other way. Never make a knot in the cord or tie it with other cables. The power cords should be routed so that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electric shock.

Check the power cord once in a while. If you find it damaged, ask your nearest Pioneer authorized independent service company for a replacement.

• Do not use any power cord other than the one supplied with this unit.

• Do not use the supplied power cord for any purpose other than that described below.

• The receiver should be disconnected by removing the mains plug from the wall socket when not in regular use, e.g., when on vacation.

Note

• After this receiver is connected to an AC outlet, a 2 second to 10 second HDMI initialization process begins.

You cannot carry out any operations during this process.

The HDMI indicator in the front panel display blinks during this process, and you can turn on this receiver once it has stopped blinking. When you set the Control with HDMI to

OFF, you can skip this process. For details about the Control with HDMI feature, see Control with

HDMI function on page 31.

1

Plug the supplied power cord into the AC IN socket on the back of the receiver.

2

Plug the other end into a power outlet.

15

En

VSX-S300_SYXCN_En.book 16 ページ 2011年4月8日 金曜日 午後8時10分

Basic Setup

16

En

Chapter 3:

Basic Setup

Canceling the Auto Power Down

When this receiver is not used over a period of several hours, it will power down automatically. The automatic power-off timer is set to six hours under factory settings, and the timing can be changed or the power-off function switched off altogether. For details, see The Auto Power Down menu on page 30.

• The Auto MCACC setup will overwrite any existing speaker settings you’ve made.

• If you connected either the surround back speaker or the front height speaker, make sure that the Pre Out setting is correctly set before performing the Auto MCACC setup

(see page 30). (Here is an explanation using the OSD screen for a surround back speaker connection.)

SLEEP SP-AB

AUDIO

DIMMER

DISP

STATUS

STANDBY/ON

D AUX A AUX

ECO

S.RTRV

TOP

MENU

MENU

TOOLS VOL iPod USB NETWORK ADAPTER

AUTO /

DIRECT

ENTER

TUNER BD DVD

ALC /

STANDARD

CD STB GAME

ADV

SURR iPod

CTRL

HOME MENU

PTY

RETURN

BAND MUTE

RECEIVER TV PORTABLE

SOUND

WING

PRESET TUNE

Canceling the demo display

The display on the front panel shows various information

(demo displays) when the receiver is not operating.

You can turn off the demo display. For details, see The FL

Demo Mode menu on page 30.

• The demo mode is canceled automatically when the Auto

MCACC setup is performed (see below).

Automatically setting up for surround sound

(MCACC)

The Auto Multi-Channel Acoustic Calibration (MCACC) setup measures the acoustic characteristics of your listening area, taking into account ambient noise, speaker size and distance, and tests for both channel delay and channel level.

After you have set up the microphone provided with your system, the receiver uses the information from a series of test tones to optimize the speaker settings and equalization for your particular room.

CAUTION

• The test tones used in the Auto MCACC setup are output at high volume.

Important

• The OSD will not appear if you have connected using the

HDMI output to your TV. Use composite connections for

Auto MCACC setup.

1

Switch on the receiver and your TV.

2

Switch the TV input to the input that connects this receiver to the TV through the corresponding composite cable.

3

Connect the microphone to the MCACC SETUP MIC jack on the front panel.

Make sure there are no obstacles between the speakers and the microphone.

STANDBY / ON

PHONES

PORTABLE /

MCACC SETUP MIC

Microphone

Tripod

If you have a tripod, use it to place the microphone so that it’s about ear level at your normal listening position. Otherwise, place the microphone at ear level using a table or a chair.

4

Press

RECEIVER

on the remote control, then press the

HOME MENU button.

The Home Menu appears on your TV. Use

/// and

ENTER on the remote control to navigate through the screens and select menu items. Press RETURN to exit the current menu.

• Press HOME MENU at any time to exit the Home Menu.

If you cancel the Auto MCACC setup at any time, the receiver automatically exits and no settings will be made.

• The screensaver automatically starts after three minutes of inactivity.

VSX-S300_SYXCN_En.book 17 ページ 2011年4月8日 金曜日 午後8時10分

Basic Setup

5

Select ‘Auto MCACC’ from the Home Menu, then press

ENTER.

Home Menu

1.Auto MCACC

2.Manual SP Setup

3.Pre Out Setting

4.Input Assign

5.HDMI Setup

6.Auto Power Down

7.FL Demo Mode

• “ Mic In!” blinks when the microphone is not connected to

MCACC SETUP MIC jack.

Try to be as quiet as possible after pressing ENTER. The system outputs a series of test tones to establish the ambient noise level.

6

Follow the instructions on-screen.

• Make sure the microphone is connected.

• When using a powered subwoofer, make sure the subwoofer is on and the volume is turned up.

• When using surround back or front height speakers, turn on the power to the amplifier to which the surround back or front height speakers are connected, and adjust the sound level to the desired level.

• See below for notes regarding background noise and other possible interference.

7

Wait for the test tones to finish.

A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present in your setup. Try to be as quiet as possible while it’s doing this.

1.Auto MCACC

Now Analyzing

Environment Check

Ambient Noise

Speaker YES/NO

Return

• For correct speaker settings, do not adjust the volume during the test tones.

8

Confirm the speaker configuration.

The configuration shown on-screen should reflect the actual speakers you have.

1.Auto MCACC

Check!

Center

Surr

Surr. Back

Subwoofer

[ YES ]

[ YES ]

[YESx2]

[ YES ]

10:Next

OK

Return

• With error messages (such as

Too much ambient noise) select RETRY after checking for ambient noise (see Other

problems when using the Auto MCACC setup below).

If the speaker configuration displayed isn’t correct, use

/ to select the speaker and

/ to change the setting. When you’re finished, go to the next step.

If you see an error message ( ERR) in the right side column, there may be a problem with the speaker connection. If selecting

RETRY doesn’t fix the problem, turn off the power and check the speaker connections.

9

Make sure ‘OK’ is selected, then press ENTER.

If the screen in step 7 is left untouched for 10 seconds and

ENTER is not pressed in step 8, the Auto MCACC setup will start automatically as shown.

1.Auto MCACC

Now Analyzing

Surround Analyzing

Speaker System

Speaker Distance

Channel Level

Acoustic Cal EQ

Return

A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum receiver settings for channel level, speaker distance, and Acoustic

Calibration EQ.

Again, try to be as quiet as possible while this is happening.

It may take 1 to 3 minutes.

10

The Auto MCACC setup has finished! You return to the

Home Menu.

The settings made in the Auto MCACC setup should give you excellent surround sound from your system, but it is also possible to adjust these settings manually using the Manual

Speaker Setup (starting on page 27).

Note

• Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around

12 cm will end up with different size settings. You can correct the setting manually using the Speaker Setting on page 28.

• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking delay and room characteristics into account) and generally does not need to be changed.

Other problems when using the Auto MCACC setup

If the room environment is not optimal for the Auto MCACC setup (too much background noise, echo off the walls, obstacles blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air conditioner, fridge, fan, etc.), that may be affecting the environment and switch them off if necessary. If there are any instructions showing in the front panel display, please follow them.

• Some older TVs may interfere with the operation of the microphone. If this seems to be happening, switch off the

TV when doing the Auto MCACC setup.

17

En

VSX-S300_SYXCN_En.book 18 ページ 2011年4月8日 金曜日 午後8時10分

Basic playback

18

En

Chapter 4:

Basic playback

Playing a source

Here are the basic instructions for playing a source (such as a DVD disc) with your home theater system.

STANDBY/ON

D AUX A AUX

ECO

S.RTRV

iPod USB NETWORK ADAPTER

AUTO /

DIRECT

TUNER BD DVD

ALC /

STANDARD

CD STB GAME

ADV

SURR

RECEIVER

TV PORTABLE

SOUND

WING

SLEEP SP-AB

AUDIO

DIMMER

DISP

STATUS

TOP

MENU

ENTER

MENU

TOOLS VOL iPod

CTRL

HOME MENU

PTY

RETURN

BAND MUTE

PRESET TUNE

1

Switch on your system components and receiver.

Start by switching on the playback component (for example a

DVD player), your TV and subwoofer (if you have one), then the receiver (press  RECEIVER).

• Make sure the setup microphone is disconnected.

2

Switch the TV input to the input that connects this receiver.

For example, if you connected this receiver to the

VIDEO jacks on your TV, make sure that the VIDEO input is now selected.

3

Press input function buttons to select the input function you want to play.

• The input of the receiver will switch over, and you will be able to operate other components using the remote control. To operate the receiver, first press

RECEIVER

on the remote control, then press the appropriate button to operate.

• The input source can also be selected by using the front panel INPUT SELECTOR button. In this case, the remote control won’t switch operational modes.

4

Press AUTO/DIRECT to select ‘AUTO SURR’ and start playback of the source.

If you’re playing a Dolby Digital or DTS surround sound DVD disc, with a digital audio connection, you should hear surround sound. If you’re playing a stereo source or if the connection is an analog audio connection, you will only hear sound from the front left/right speakers in the default listening mode.

It is possible to check on the front panel display whether or not surround sound playback is being performed properly.

If the display does not correspond to the input signal and listening mode, check the connections and settings.

Note

• You may need to check the digital audio output settings on your DVD player or digital satellite receiver. It should be set to output Dolby Digital, DTS and 88.2 kHz/96 kHz

PCM (2 channel) audio, and if there is an MPEG audio option, set this to convert the MPEG audio to PCM.

• Depending on your DVD player or source discs, you may only get digital 2 channel stereo and analog sound. In this case, the receiver must be set to a multichannel listening mode if you want multichannel surround sound.

5

Use VOL +/– to adjust the volume level.

Turn down the volume of your TV so that all sound is coming from the speakers connected to this receiver.

• If channel levels are calibrated using Auto MCACC setup,

“0 dB” represents a level roughly equivalent to the volume of a movie theater (i.e., it is loud; please be considerate of small children and neighbors when adjusting the volume.)

Note

• When digital input (optical or coaxial) is selected, this receiver can only play back Dolby Digital, PCM (32 kHz to

96 kHz) and DTS (including DTS 96 kHz/24 bit) digital signal formats. The compatible signals via the HDMI terminals are: Dolby Digital, DTS, SACD (DSD 2 ch only),

PCM (32 kHz to 192 kHz sampling frequencies), Dolby

TrueHD, Dolby Digital Plus, DTS-EXPRESS, DTS-HD

Master Audio and DVD Audio (including 192 kHz). With other digital signal formats, chose analog input.

• You may get digital noise when a LD or CD player compatible with DTS is playing an analog signal. To prevent noise, make the proper digital connections

(page 12).

• Some DVD players don’t output DTS signals. For more details, refer to the instruction manual supplied with your

DVD player.

Bluetooth

®

ADAPTER for Wireless Enjoyment of Music

Bluetooth wireless technology enabled device: cell phone

Bluetooth wireless technology enabled device:

Digital music player

Device not equipped with Bluetooth wireless technology: Digital music player + Bluetooth audio transmitter (sold commercially)

Music data

This receiver

Bluetooth

®

ADAPTER

Remote control operation

VSX-S300_SYXCN_En.book 19 ページ 2011年4月8日 金曜日 午後8時10分

Basic playback

Wireless music play

When the Bluetooth ADAPTER (Pioneer Model No. AS-BT100 or AS-BT200) is connected to this unit, a product equipped with Bluetooth wireless technology (portable cell phone, digital music player, etc.) can be used to listen to music wirelessly. Also, by using a commercially available transmitter supporting Bluetooth wireless technology, you can listen to music on a device not equipped with Bluetooth wireless technology. The AS-BT100 and AS-BT200 model supports SCMS-T contents protection, so music can also be enjoyed on devices equipped with SCMS-T type Bluetooth wireless technology.

• It must be necessary that the Bluetooth wireless technology enabled device supports A2DP profiles.

Important

• Pioneer does not guarantee proper connection and operation of this unit with all Bluetooth wireless technology enabled devices.

Remote control operation

The remote control supplied with this unit allows you to play and stop media, and perform other operations.

• It must be necessary that the Bluetooth wireless technology enabled device supports AVRCP profiles.

• Remote control operations cannot be guaranteed for all

Bluetooth wireless technology enabled devices.

Pairing the Bluetooth ADAPTER and Bluetooth wireless technology device

“Pairing” must be done before you start playback of Bluetooth wireless technology content using Bluetooth ADAPTER.

Make sure to perform pairing first time you operate the system or any time pairing data is cleared. “Pairing” is the step necessary to register Bluetooth wireless technology device to enable Bluetooth communications. For more details, see also the operating instructions of your Bluetooth wireless technology device.

• Pairing is required when you first use Bluetooth wireless technology device and Bluetooth ADAPTER.

• To enable Bluetooth communication, pairing should be done with both of your system and Bluetooth wireless technology device.

• If the Bluetooth wireless technology device’s security code is “0000”, there is no need to make the security code setting on the receiver. Press ADAPTER to switch the

ADAPTER input, then conduct the pairing operation on the Bluetooth wireless technology device. If pairing is successful, there is no need to performing the pairing operation below.

• When using the AS-BT200 only: If the Bluetooth wireless technology device supports SSP (Secure Simple Pairing), there is no need to make the security code setting. Press

ADAPTER to switch the ADAPTER input, then conduct the pairing operation on the Bluetooth wireless technology device. If pairing is successful, there is no need to performing the pairing operation below.

1

Press TOP MENU.

2

Press ENTER to enter PAIRING.

3

Select the PIN code to be used from 0000/1234/8888 using

/, then press ENTER.

PAIRING blinks.

• You can use any of 0000/1234/8888 PIN codes. Bluetooth wireless technology device using any other PIN code cannot be used with this system.

4

Switch on the Bluetooth wireless technology device that you want to make pairing, place it near the system and set it into the pairing mode.

5

Check to see that the Bluetooth ADAPTER is detected by the

Bluetooth

wireless technology device.

When Bluetooth wireless technology device is connected:

Bluetooth wireless technology device name appears in the receiver display.

• The system can display alphanumeric characters only.

Other characters may not be displayed correctly.

When Bluetooth wireless technology device is not connected:

NODEVICE appears in the receiver display. In this case, perform the connection operation from the side of the

Bluetooth wireless technology device.

6

From the

Bluetooth

wireless technology device list, select Bluetooth ADAPTER and enter the PIN code selected in the step 4.

• PIN code may in some case be referred to as PASSKEY.

Listening to Music Contents of Bluetooth wireless technology device with Your System

1

Press ADAPTER to switch the receiver to ADAPTER input.

2

Perform the connection operation from the side of the

Bluetooth wireless technology device to the Bluetooth

ADAPTER.

• When the Bluetooth ADAPTER is not plugged into the

ADAPTER PORT terminal, NO ADAPT will be displayed if

ADAPTER input is selected.

3

Start playback of music contents stored in Bluetooth wireless technology device.

This receiver’s remote control buttons can be used for basic playback of files stored on the Bluetooth wireless technology device.

Bluetooth wireless technology device should be compatible with AVRCP profile.

• Depending on Bluetooth wireless technology device you use, operation may differ from what is shown in the remote control buttons.

PTY BAND MUTE

PRESET TUNE

The Bluetooth

®

word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by PIONEER CORPORATION is under license. Other trademarks and trade names are those of their respective owners.

19

En

VSX-S300_SYXCN_En.book 20 ページ 2011年4月8日 金曜日 午後8時10分

Basic playback

20

En

Listening to the radio

The following steps show you how to tune in to FM and AM radio broadcasts using the automatic (search) and manual

(step) tuning functions. Once you are tuned to a station you can memorize the frequency for recall later—see Saving

station presets below for more on how to do this.

TOP

MENU

MENU

TOOLS VOL

STANDBY/ON

D AUX A AUX

ECO

S.RTRV

ENTER iPod USB NETWORK ADAPTER

AUTO /

DIRECT

TUNER BD DVD

ALC /

STANDARD iPod

CTRL

HOME MENU

PTY

RETURN

BAND MUTE

CD STB GAME

ADV

SURR

PRESET TUNE

RECEIVER TV PORTABLE

SOUND

WING

1

Press TUNER to select the tuner.

2

Use BAND to change the band (FM or AM), if necessary.

Each press switches the band between FM (stereo or mono) and AM.

3

Tune to a station.

There are three ways to do this:

Automatic tuning

To search for stations in the currently selected band, press and hold TUNE +/– (or

/) for about a second.

The receiver will start searching for the next station, stopping when it has found one. Repeat to search for other stations.

Manual tuning

To change the frequency one step at a time, press

TUNE +/– (or

/).

High speed tuning

Press and hold TUNE +/– (or

/) for high speed tuning.

Release the button at the frequency you want.

– Lights when a normal broadcast channel.

– Lights when a stereo FM broadcast is being received in auto stereo mode.

Improving FM sound

If the or indicators don’t light when tuning to an FM station because the signal is weak, set the receiver to the mono reception mode.

Press BAND to select FM MONO.

This should improve the sound quality and allow you to enjoy the broadcast.

Saving station presets

If you often listen to a particular radio station, it’s convenient to have the receiver store the frequency for easy recall whenever you want to listen to that station. This saves the effort of manually tuning in each time. This unit can memorize up to 30 stations.

SLEEP SP-AB

AUDIO

DIMMER

DISP

STATUS

STANDBY/ON

D AUX A AUX

ECO

S.RTRV

TOP

MENU

MENU

TOOLS

VOL iPod USB NETWORK ADAPTER

AUTO /

DIRECT

TUNER BD DVD

ALC /

STANDARD

CD STB GAME

ADV

SURR

RECEIVER

TV PORTABLE

SOUND

WING

ENTER iPod

CTRL

HOME MENU

PTY

RETURN

BAND MUTE

PRESET TUNE

1

Tune to a station you want to memorize.

See Listening to the radio below for more on this.

2

Press TOOLS.

The preset number is blinking.

3

Press PRESET +/– (or

/) to select the station preset

you want.

4

Press ENTER.

The preset number stop blinking and the receiver stores the station.

Note

• If the receiver is left disconnected from the AC power outlet for over a month, the station memories will be lost and will have to be reprogrammed.

• Stations are stored in stereo. When the station is stored in the FM MONO mode, it shows as when recalled.

Listening to station presets

You will need to have some presets stored to do this. See

Saving station presets above if you haven’t done this already.

Press PRESET +/– (or /) to select the station preset

you want.

Naming preset stations

For easier identification, you can name all of your preset stations.

1

Choose the station preset you want to name.

See Listening to station presets above for how to do this.

2

Press TOOLS twice.

The cursor at the first character position is blinking on the display.

3

Input the name you want.

Choose a name up to eight characters long.

• Use PRESET +/– (or

/) to select character position.

• Use TUNE +/– (or

/) to select characters.

• The name is stored when ENTER is pressed.

Tip

• To erase a station name, follow steps 1 and 2, and press

ENTER while the display is blank. Press TOOLS while the display is blank, to keep the previous name.

• Once you have named a station preset, Press DISP to show the name. When you want to return to the frequency display, press

DISP several times to show the frequency.

VSX-S300_SYXCN_En.book 21 ページ 2011年4月8日 金曜日 午後8時10分

Basic playback

An introduction to RDS

Radio Data System (RDS) is a system used by most FM radio stations to provide listeners with various kinds of information—the name of the station and the kind of show they’re broadcasting, for example.

One feature of RDS is that you can search by type of program.

For example, you can search for a station that’s broadcasting a show with the program type, JAZZ.

You can search the following program types:

NEWS – News

AFFAIRS – Current Affairs

INFO – General Information

SPORT – Sport

EDUCATE – Educational

DRAMA – Radio plays, etc.

CULTURE – National or regional culture, theater, etc.

SCIENCE – Science and technology

VARIED – Usually talk-based material, such as quiz shows or interviews.

POP M – Pop music

ROCK M – Rock music

EASY M – Easy listening

LIGHT M – ‘Light’ classical music

CLASSICS – ‘Serious’ classical music

OTHER M – Music not fitting above categories

WEATHER – Weather reports

FINANCE – Stock market reports, commerce, trading, etc.

CHILDREN – Programs for children

SOCIAL – Social affairs

RELIGION – Programs concerning religion

PHONE IN – Public expressing their views by phone

TRAVEL – Holiday-type travel rather than traffic announcements

LEISURE – Leisure interests and hobbies

JAZZ – Jazz

COUNTRY – Country music

NATION M – Popular music in a language other than English

OLDIES – Popular music from the ’50s and ’60s

FOLK M – Folk music

DOCUMENT – Documentary

Note

• In addition, there are three other program types, ALARM,

ALARMTST, and NO TYPE. ALARM and ALARMTST are used for emergency announcements.

NO TYPE appears when a program type cannot be found.

STANDBY/ON

D AUX A AUX

ECO

S.RTRV

iPod USB NETWORK ADAPTER

AUTO /

DIRECT

TUNER BD DVD

ALC /

STANDARD

CD STB GAME

ADV

SURR

RECEIVER

TV PORTABLE

SOUND

WING

SLEEP SP-AB

AUDIO

DIMMER

DISP

STATUS

TOP

MENU

MENU

TOOLS VOL

ENTER iPod

CTRL

HOME MENU

PTY

RETURN

BAND MUTE

PRESET TUNE

Searching for RDS programs

You can search for a program type listed above.

1

Press TUNER then press BAND to select the FM band.

• RDS is only possible in the FM band.

2

Press PTY.

SEARCH shows in the display.

3

Press PRESET +/– (or

/) to select the program type

you want to hear.

4

Press ENTER to search for the program type.

The system starts searching through the station presets for a match, stopping when it was found one. Repeat to search for other stations.

If NO PTY is displayed it means the tuner couldn’t find that program type at the time of the search.

• RDS searches station presets only. If no stations have been preset, or if the program type could not be found among the station presets NO PTY is displayed. FINISH means the search is complete.

Displaying RDS information

Use the DISP button to display the different types of RDS information available.

Press DISP for RDS information.

Each press changes the display as follows:

• Listening mode

• Master volume

• Radio Text ( RT) – Messages sent by the radio station. For example, a talk radio station may provide a phone number as RT.

• Program Service Name ( PS) – The name of the radio station.

• Program Type ( PTY) – This indicates the kind of program currently being broadcast.

• Current tuner frequency ( FREQ)

Note

• If any noise is picked up while displaying the RT scroll, some characters may be displayed incorrectly.

• If you see

NO TEXT in the RT display, it means no RT data is sent from the broadcast station. The display will automatically switch to the PS data display (if no PS data,

NO NAME is displayed).

• In the PTY display, NO PTY may be shown.

21

En

VSX-S300_SYXCN_En.book 22 ページ 2011年4月8日 金曜日 午後8時10分

Listening to your system

22

En

Chapter 5:

Listening to your system

Choosing the listening mode

This receiver offers a variety of listening modes to accommodate playback of various audio formats. Choose one according to your speaker environment or the source.

While listening to a source, press the listening mode

button repeatedly to select a listening mode you want.

iPod USB NETWORK ADAPTER

AUTO /

DIRECT

TUNER

CD

BD DVD

ALC /

STANDARD

STB GAME

ADV

SURR

RECEIVER TV PORTABLE

SOUND

WING

• The listening mode is shown on the display on the front panel.

Important

• The listening modes and many features described in this section may not be available depending on the current source, settings and status of the receiver.

Auto playback

AUTO /

DIRECT

The simplest, most direct listening option is the AUTO SURR feature. With this, the receiver automatically detects what kind of source you’re playing and selects multichannel or stereo playback as necessary.

• Press AUTO/DIRECT repeatedly until AUTO SURR shows briefly in the display (it will then show the decoding or playback format). Check the digital format indicators in the display to see how the source is being processed.

Note

• Stereo surround (matrix) formats are decoded accordingly using NEO:6 CINEMA or 2PLIIx MOVIE

(see Listening in surround sound below for more on these decoding formats).

• When listening to the ADAPTER input, the S.R AIR feature is selected automatically (see Using the Advanced

surround on page 23 for more on this).

Listening in surround sound

ALC /

STANDARD

Using this receiver, you can listen to any source in surround sound. However, the options available will depend on your speaker setup and the type of source you’re listening to.

• If the source is Dolby Digital, DTS, or Dolby Surround encoded, the proper decoding format will automatically be selected and shows in the display.

When you select STEREO ALC (Auto Level Control stereo mode), this unit equalizes playback sound levels if each sound level varies with the music source recorded in a portable audio player.

When you select STEREO, you will hear the source through just the front left and right speakers (and possibly your subwoofer depending on your speaker settings). Dolby

Digital and DTS multichannel sources are downmixed to stereo.

The following modes provide basic surround sound for stereo and multichannel sources.

Explanatory notes

No: No connected / Yes: Connected / Two: Two speakers are

connected / –: Whether connected or no

Type of surround modes

Suitable sources

Two channel sources

STEREO ALC

2PRO LOGIC

2PLIIx MOVIE

See above.

Old movies

Movie

2PLII MOVIE

2PLIIx MUSIC

b

2PLII MUSIC

b

2PLIIx GAME

STEREO ALC

2PLIIx MOVIE

Music

Video games

2PLII GAME

2PLIIz HEIGHT

c

Straight Decode

d

Movie/Music

No additional effects

NEO:6 CINEMA e

NEO:6 MUSIC e

STEREO f

Multichannel sources

Movie

Music

See above.

See above.

Movie

2PLII MOVIE

2PLIIx MUSIC

b

2PLII MUSIC

b

2DIGITAL EX

2PLIIz HEIGHT

Straight Decode

d

DTS-ES

DTS NEO:6

STEREO f

Music

Movie/Music

Movie/Music

No additional effects

Movie/Music

Movie/Music

See above.

No

Yes

No

No

No

No

Yes

No

Yes

Yes

Two a

No

Two a

No

No

No

No

Yes

Yes a

No

No

No

Yes a

No

Yes a

No

VSX-S300_SYXCN_En.book 23 ページ 2011年4月8日 金曜日 午後8時10分

Listening to your system

a. If surround back channel processing (page 25) is switched off, or the surround back speakers are set to NO, 2PLIIx becomes

2PLII (5.1 channel sound).

b. You can also adjust the CENTER WIDTH, DIMENSION, and

PANORAMA effect (see Setting the Audio options on page 24).

c. You can also adjust the HEIGHT GAIN effect (see Setting the

Audio options on page 24).

d. Cannot be selected when the Pre Out is set to Surr. Back (see

The Pre Out Setting on page 30).

e. You can also adjust the CENTER IMAGE effect (see Setting the

Audio options on page 24).

f.

The audio is heard with your surround settings and you can still use the Midnight, Loudness, Phase Control, Sound

Retriever and Tone functions.

Note

• In modes that give 6.1 channel sound, the same signal is heard from both surround back speakers.

FSS ADVANCE

(Front Stage

Surround

ADVANCE)

Using the Advanced surround

ADV

SURR

The Advanced surround feature creates a variety of surround effects. Try different modes with various soundtracks to see which you like.

ACTION

DRAMA

ENT.SHOW

ADV GAME

SPORTS

CLASSICAL

ROCK/POP

UNPLUGGED

EXT.STEREO

Designed for action movies with dynamic soundtracks.

Designed for movies with lots of dialog.

Suitable for musical sources.

Suitable for video games.

Suitable for sports programs.

Gives a large concert hall-type sound

Creates a live concert sound for rock and/or pop music.

Suitable for acoustic music sources.

Gives multichannel sound to a stereo source, using all of your speakers

Allows you to create natural surround sound effects using just the front speakers and the subwoofer.

Use to provide a rich surround sound effect directed to the center of where the front left and right speakers sound projection area converges.

Front left speaker

Front right speaker

SOUND WING

S.R AIR

(Sound Retriever

AIR)

PHONES SURR

HVT speakers make it possible to enjoy a broader-ranging sound.

SOUND WING mode can be selected only when the HVT speakers (e.g., S-

HV500-LR) are connected and the

Speaker Setting other than the front speakers and subwoofer are set to

NO via the Auto MCACC setup.

• You can choose the SOUND WING mode by using SOUND WING button on the remote control.

Suitable for listening to the sound from a

Bluetooth wireless technology device.

The S.R AIR listening mode can only selected when the ADAPTER input.

When listening through headphones, you can still get the effect of overall surround.

Using Stream Direct

AUTO /

DIRECT

Use the Stream Direct modes when you want to hear the truest possible reproduction of a source. All unnecessary signal processing is bypassed.

AUTO SURR

DIRECT

PURE DIR

See Auto playback on page 22.

Sources are heard according to the settings made in the Manual SP Setup (speaker setting, channel level, speaker distance), as well as with dual mono settings. You will hear sources according to the number of channels in the signal.

Phase Control, Acoustic Calibration EQ,

Sound Delay, Auto Delay, LFE Attenuate and Center image functions are available.

Analog and PCM sources are heard without any digital processing.

Using the Ecology mode

Select Ecology mode to enjoy the full benefits of great sound with half the regular power consumption.

STANDBY/ON

ECO

S.RTRV

D AUX A AUX iPod USB NETWORK ADAPTER

AUTO /

DIRECT

ALC/

Press ECO to switch the ECO MODE ON or OFF.

• The power will switch once to standby when Ecology mode is switched on or cancelled.

• Ecology mode offers the following power-saving benefits.

-

Sound is output from only the front-left, front-right and subwoofer.

-

The front panel display dimmer is activated.

• Ecology mode can be cancelled by switching the input function.

23

En

VSX-S300_SYXCN_En.book 24 ページ 2011年4月8日 金曜日 午後8時10分

Listening to your system

24

En

Using the Sound Retriever

When audio data is removed during the compression process, sound quality often suffers from an uneven sound image. The Sound Retriever feature employs new DSP technology that helps bring CD quality sound back to compressed 2-channel audio by restoring sound pressure and smoothing jagged artifacts left over after compression.

STANDBY/ON

ECO

S.RTRV

D AUX A AUX iPod USB NETWORK ADAPTER

AUTO /

DIRECT

ALC/

Press S.RTRV to switch the SOUND RTRV (Sound

Retriever) ON or OFF.

Note

• The Sound Retriever is only applicable to 2-channel sources.

Setting the Up Mix function

In a 7.1-channel surround system with surround speakers placed directly at the sides of the listening position, the surround sound of 5.1-channel sources is heard from the side. The Up Mix function mixes the sound of the surround speakers with the surround back speakers so that the surround sound is heard from diagonally to the rear as it should be.

• Using the Up Mix function is effective when the speakers in the 7.1-channel surround system are set up as recommended in the example on page 9.

• Depending on the positions of the speakers and the sound source, in some cases it may not be possible to achieve good results. In this case, set the setting to OFF.

UPMIX OFF UPMIX ON

L

C SW

R L

C SW

R

Setting the Audio options

There are a number of additional sound settings you can make using the TOOLS menu. The defaults, if not stated, are listed in bold.

Important

• Note that if a setting doesn’t appear in the TOOLS menu, it is unavailable due to the current source, settings and status of the receiver.

RECEIVER TV PORTABLE

SOUND

WING

SLEEP SP-AB

AUDIO

DIMMER

DISP

STATUS

TOP

MENU

MENU

TOOLS VOL

ENTER

SL SR SL SR

SBL SBR SBL SBR

1

Switch the receiver into standby.

2

Press and hold INPUT SELECTOR button on the front panel for more than five seconds, and then press TUNER button on the remote control.

UPMIX OFF appears and the Up Mix function turns off. If you want to turn this function on, perform steps 1 and 2 again.

Note

• Set to ON regardless of this setting when playing DTS-HD signals.

• May automatically be set to OFF even when set to ON, depending on the input signal and listening mode.

iPod

CTRL

HOME MENU RETURN

1

Press RECEIVER , then press TOOLS button.

2

Use

/ to select the setting you want to adjust.

Depending on the current status/mode of the receiver, certain options may not be able to be selected. Check the table below for notes on this.

3

Use

/ to set it as necessary.

See the table below for the options available for each setting.

4

Press RETURN to confirm and exit the menu.

Setting/What it does Option(s)

MIDNIGHT/LOUDNESS

The MIDNIGHT allows you to hear effective surround sound of movies at low volumes.

The

LOUDNESS is used to get good bass and treble from music sources at low volumes.

MID/LDN OFF

MIDNIGHT

LOUDNESS

BASS a

Adjust the bass level to accentuate or minimize the bottom end.

–6 to +6

Default:

0

VSX-S300_SYXCN_En.book 25 ページ 2011年4月8日 金曜日 午後8時10分

Listening to your system

Setting/What it does

TREBLE

Adjust the treble level to accentuate or minimize the bottom end.

CH LEV (Channel Level)

b

Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor when setting up a home theater system.

SB CH (Surround back channel processing)

c

You can have the receiver automatically use

6.1 or 7.1 decoding for 6.1 encoded sources

(for example, Dolby Digital EX or DTS-ES), or you can choose to always use 6.1 or 7.1 decoding (for example, with 5.1 encoded material). With 5.1 encoded sources, a surround back channel will be generated, but the material may sound better in the 5.1 format for which it was originally encoded (in which case, you can simply switch surround back channel processing off).

When ON is selected, matrix decoding processing for generating the surround back component from the surround component is turned on.

When AUTO is selected, matrix decoding processing for generating the surround back component from the surround component is switched automatically. Matrix decoding processing is only performed when surround back channel signals are detected in the input signals.

When OFF is selected, matrix decoding processing for generating the surround back component from the surround component is turned off.

Option(s)

–6 to +6

Default:

0

–15 to +15

Default:

ON

AUTO

OFF

0

Setting/What it does

PHASE CTRL (Phase Control)

d

Phase Control feature uses phase correction measures to make sure your sound source arrives at the listening position in phase, preventing unwanted distortion and/or coloring of the sound.

Phase Control technology provides coherent sound reproduction through the use of phase matching for an optimal sound image at your listening position. The default setting is on and we recommend leaving Phase Control switched on for all sound sources.

EQ (Acoustic Calibration EQ)

Switches on/off the effect of Acoustic

Calibration EQ.

Option(s)

ON

OFF

ON

OFF

SOUND DELAY

Some monitors have a slight delay when showing video, so the soundtrack will be slightly out of sync with the picture. By adding a bit of delay, you can adjust the sound to match the presentation of the video.

0.0 to 9.0

(frames)

1 second = 25 frames (PAL)

Default:

0.0

SOUND RTRV (Sound Retriever)

e

When audio data is removed during the compression process, sound quality often suffers from an uneven sound image. The

Sound Retriever feature employs new DSP technology that helps bring CD quality sound back to compressed 2-channel audio by restoring sound pressure and smoothing jagged artifacts left over after compression.

DUAL (Dual monaural)

g

Specifies how dual mono encoded Dolby

Digital soundtracks should be played.

OFF

ON

f

CH1 – Channel 1 is heard only

CH2 – Channel 2 is heard only

CH1 CH2 – Both channels heard from front speakers

Setting/What it does

FIXED PCM

This is useful if you find there is a slight delay before OFF recognizes the PCM signal on a

CD, for instance.

When ON is selected, noise may be output during playback of non-PCM sources. Please select another input signal if this is a problem.

Option(s)

OFF

ON

DRC (Dynamic Range Control)

Adjusts the level of dynamic range for movie soundtracks optimized for Dolby Digital, DTS,

Dolby Digital Plus, Dolby TrueHD, DTS-HD and DTS-HD Master Audio (you may need to use this feature when listening to surround sound at low volumes).

LFE ATT (LFE Attenuate)

Some Dolby Digital and DTS audio sources include ultra-low bass tones. Set the LFE attenuator as necessary to prevent the ultralow bass tones from distorting the sound from the speakers.

The LFE is not limited when set to 0 dB, which is the recommended value. When set to –15 dB, the LFE is limited by the respective degree. When OFF is selected, no sound is output from the LFE channel.

SACD GAIN i

Brings out detail in SACDs by maximizing the dynamic range (during digital processing).

HDMI (HDMI Audio)

Specifies the routing of the HDMI audio signal out of this receiver ( AMP) or through to a TV

( THROUGH). When THROUGH is selected, no sound is output from this receiver.

AUTO DELAY j

This feature automatically corrects the audioto-video delay between components connected with an HDMI cable. The audio delay time is set depending on the operational status of the display connected with an HDMI cable. The video delay time is automatically adjusted according to the audio delay time.

AUTO h

MAX

MID

OFF

0dB

–5dB

–10dB

–15dB

–20dB

OFF

0 (dB)

+6 (dB)

AMP

THROUGH

OFF

ON

25

En

VSX-S300_SYXCN_En.book 26 ページ 2011年4月8日 金曜日 午後8時10分

Listening to your system

26

En

Setting/What it does

CENTER WIDTH k

(Applicable only when using a center speaker)

Spreads the center channel between the front right and left speakers, making it sound wider

(higher settings) or narrower (lower settings).

Option(s)

0 to 7

Default:

3

–3 to +3

Default:

0

DIMENSION k

Adjusts the surround sound balance from front to back, making the sound more distant

(minus settings), or more forward (positive settings).

PANORAMA k

Extends the front stereo image to include surround speakers for a ‘wraparound’ effect.

OFF

ON

CENTER IMAGE l

(Applicable only when using a center speaker)

Adjust the center image to create a wider stereo effect with vocals. Adjust the effect from 0 (all center channel sent to front right and left speakers) to 10 (center channel sent to the center speaker only).

0 to 10

Default: 3

(NEO:6 MUSIC),

10 (NEO:6

CINEMA)

HEIGHT GAIN

Adjusts the output from the front height speaker when listening in

2PLIIz HEIGHT mode. If set to

HIGH, the sound from the top will be more emphasized.

HIGH

MID

LOW

a. BASS settings cannot be adjusted when the front speaker is set to SMALL in the Speaker Setting (or is set automatically via the Auto MCACC setup) and the X.OVER is set above 150 Hz.

In this case, adjusting the subwoofer channel levels via

CH

LEV allows for similar adjustments to those that could otherwise be performed via

BASS (page 29).

b. • Channels are displayed as follows.

FL – Front left

FHL – Front height left

C – Center

FHR – Front height right

FR – Front right

SR – Surround right

SBR – Surround back right

SBL – Surround back left

SL – Surround left

SW – Subwoofer

• Speakers for which Speaker Settings are set to NO cannot be selected.

c. With a 7.1-channel surround system, audio signals that have undergone matrix decoding processing through surround back channel processing to which the Up Mix function is added are output from the surround back speakers.

d. • Phase matching is a very important factor in achieving proper sound reproduction. If two waveforms are ‘in phase’, they crest and trough together, resulting in increased amplitude, clarity and presence of the sound signal. If a crest of a wave meets a trough, then the sound will be ‘out of phase’ and an unreliable sound image will be produced.

• If your subwoofer has a phase control switch, set it to the plus (+) sign (or 0°). However, the effect you can actually feel when Phase Control is set to ON on this receiver depends on the type of your subwoofer. Set your subwoofer to maximize the effect. It is also recommended you try changing the orientation or the place of your subwoofer.

• Set the built-in lowpass filter switch of your subwoofer to

OFF. If this cannot be done on your subwoofer, set the cutoff frequency to a higher value.

• If the speaker distance is not properly set, you may not have a maximized Phase Control effect.

• The Phase Control mode cannot be set to ON in the following cases:

– When the PURE DIR mode is switched on.

– When the headphones are connected.

e. You can change the Sound Retriever feature at any time by using S.RTRV button.

f.

The default setting when the ADAPTER input is selected is

ON.

g. This setting works only with dual mono encoded Dolby Digital and DTS soundtracks.

h. The initial set AUTO is only available for Dolby TrueHD signals.

Select MAX or MID for signals other than Dolby TrueHD.

i.

You shouldn’t have any problems using this with most SACD discs, but if the sound distorts, it is best to switch the gain setting back to

0 dB.

j.

This feature is only available when the connected display supports the automatic audio/video synchronizing capability

(‘lip-sync’) for HDMI. If you find the automatically set delay time unsuitable, set AUTO DELAY to OFF and adjust the delay time manually. For more details about the lip-sync feature of your display, contact the manufacturer directly.

k. Only available with 2-channel sources in 2PLII MUSIC mode.

l.

Only when listening to 2-channel sources in NEO:6 CINEMA and

NEO:6 MUSIC mode.

VSX-S300_SYXCN_En.book 27 ページ 2011年4月8日 金曜日 午後8時10分

The Home Menu

Chapter 6:

The Home Menu

Using the Home Menu

The following section shows you how to make detailed settings to specify how you’re using the receiver, and also explains how to fine-tune individual speaker system settings to your liking.

Important

• The OSD will not appear if you have connected using the

HDMI output to your TV. Use composite connections for

Home Menu.

• If headphones are connected to the receiver, disconnect them.

SLEEP SP-AB

AUDIO

DIMMER

DISP

STATUS

STANDBY/ON

D AUX A AUX

ECO

S.RTRV

TOP

MENU

MENU

TOOLS VOL iPod USB NETWORK ADAPTER

AUTO /

DIRECT

ENTER

TUNER BD DVD

ALC /

STANDARD

CD STB GAME

ADV

SURR iPod

CTRL

HOME MENU

PTY

RETURN

BAND MUTE

RECEIVER TV PORTABLE

SOUND

WING

PRESET TUNE

1

Switch on the receiver and your TV.

Press  RECEIVER to switch on.

2

Switch the TV input to the input that connects this receiver to the TV through the corresponding composite cable.

3

Press RECEIVER , then press HOME MENU.

The Home Menu appears on your TV. Use

/// and

ENTER on the remote control to navigate through the screens and select menu items. Press RETURN to confirm and exit the current menu.

• Press HOME MENU at any time to exit the Home Menu.

4

Select the setting you want to adjust.

Home Menu

1.Auto MCACC

2.Manual SP Setup

3.Pre Out Setting

4.Input Assign

5.HDMI Setup

6.Auto Power Down

7.FL Demo Mode

Auto MCACC – This is a quick and effective automatic surround setup (see Automatically setting up for surround

sound (MCACC) on page 16).

Manual SP Setup

-

Speaker System – Specify how to use the Speaker B terminal (see below).

-

Speaker Setting – Specify the size and number of speakers you’ve connected (see below).

-

X.OVER – Specify which frequencies will be sent to the subwoofer (page 28).

-

Channel Level – Adjust the overall balance of your speaker system (page 29).

-

Speaker Distance – Specify the distance of your speakers from the listening position (page 29).

Pre Out Setting – Specify how to use the PRE OUT SURR

BACK/FRONT HEIGHT outputs (see The Pre Out Setting on page 30).

Input Assign – Specify what you’ve connected to the

ANALOG AUX (composite) video input (see The Input

Assign menu on page 30).

HDMI Setup – Sets synchronized operations when connected to a device/TV that supports the Control with

HDMI function (see HDMI Setup on page 31).

Auto Power Down – Sets to automatically turn off the power when the receiver has not operated for several hours (see The Auto Power Down menu on page 30).

FL Demo Mode – Sets the demo display on the front panel display (see The FL Demo Mode menu on page 30).

Manual speaker setup

This receiver allows you to make detailed settings to optimize the surround sound performance. You only need to make these settings once (unless you change the placement of your current speaker system or add new speakers).

These settings are designed to fine-tune your system, but if you’re satisfied with the settings made in Automatically

setting up for surround sound (MCACC) on page 16, it isn’t necessary to make all of these settings.

CAUTION

• The test tones used in the channel level setting are output at high volume.

Important

• Depending on the Pre Out Setting, there will be differences in the speaker items that can be adjusted. The

OSD display for these operating instructions is an example of when the Pre Out Setting is set to Surr. Back.

Speaker System

• Default setting:

Normal

Select the use for the Speaker B terminal. Speakers connected via the Speaker B terminal can be used as 5.1ch surround sound speakers or can be placed in another room to enable sound to be heard in stereo.

1

Select ‘Manual SP Setup’ from the Home Menu.

2

Select ‘Speaker System’ from the Manual SP Setup menu.

2.Manual SP Setup a.Speaker System b.Speaker Setting c.X.OVER

d.Channel Level e.Speaker Distance

2a.Speaker System

Normal

Return

Return

3

Use

/ to select the speaker system setting.

Select Normal if surround speakers are going to be connected, and Speaker B if it is going to be used in another room as Speaker B.

27

En

VSX-S300_SYXCN_En.book 28 ページ 2011年4月8日 金曜日 午後8時10分

The Home Menu

28

En

Important

• Reset the Auto MCACC if changes are made to the

Speaker System setting.

Speaker Setting

Use this setting to specify your speaker configuration (size, number of speakers). It is a good idea to make sure that the settings made in Automatically setting up for surround sound

(MCACC) on page 16 are correct.

1

Select ‘Manual SP Setup’ from the Home Menu.

2

Select ‘Speaker Setting’ from the Manual SP Setup menu.

2.Manual SP Setup a.Speaker System b.Speaker Setting c.X.OVER

d.Channel Level e.Speaker Distance

2b.Speaker Setting

Front

Center

SMALL

[ SMALL ]

Surr

Surr. Back

[ SMALL ]

[ NO ]

Subwoofer: YES

Return

Return

3

Choose the set of speakers that you want to set then select a speaker size.

Use

/ to select the size (and number) of each of the following speakers:

Front – Select LARGE if your front speakers reproduce bass frequencies effectively, or if you didn’t connect a subwoofer. Select

SMALL to send the bass frequencies to the subwoofer.

Center – Select LARGE if your center speaker reproduces bass frequencies effectively, or select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn’t connect a center speaker, choose NO (the center channel is sent to the other speakers).

Front Height – Select LARGE if your front height speakers reproduce bass frequencies effectively. Select

SMALL to send bass frequencies to the other speakers or subwoofer. If you didn’t connect front height speakers choose NO.

-

You can only adjust the Front Height setting when Pre

Out Setting is set to Height.

Surr – Select LARGE if your surround speakers reproduce bass frequencies effectively. Select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn’t connect surround speakers choose NO (the sound of the surround channels is sent to the other speakers).

Surr. Back – Select the number of surround back speakers you have (one, two or none). Select LARGE if your surround back speakers reproduce bass frequencies effectively. Select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn’t connect surround back speakers choose NO.

You can only adjust the

Surr. Back setting when Pre

Out Setting is set to Surr. Back.

If you select one surround back speaker only, make sure that additional amplifier is hooked up to the

PRE OUT L

(Single) terminal.

Subwoofer – LFE signals and bass frequencies of channels set to SMALL are output from the subwoofer when YES is selected (see notes below). Choose the PLUS setting if you want the subwoofer to output bass sound continuously or you want deeper bass (the bass frequencies that would normally come out the front and center speakers are also routed to the subwoofer). If you did not connect a subwoofer choose

NO (the bass frequencies are output from other speakers).

4

When you’re finished, press RETURN.

You return to the Manual SP Setup menu.

Note

• Only the Front and Center speakers and Subwoofer settings can be adjusted when the Speaker System setting is set to Speaker B.

• If you select

SMALL for the front speakers, the subwoofer will automatically be fixed to YES. Also, the center, surround, surround back and front height speakers can’t be set to LARGE if the front speakers are set to SMALL. In this case, all bass frequencies are sent to the subwoofer.

• If the surround speakers are set to NO, the surround back speakers will automatically be set to

NO.

• If you have a subwoofer and like lots of bass, it may seem logical to select LARGE for your front speakers and PLUS for the subwoofer. This may not, however, yield the best bass results. Depending on the speaker placement of your room you may actually experience a decrease in the amount of bass due to low frequency cancellations. In this case, try changing the position or direction of speakers. If you can’t get good results, listen to the bass response with it set to PLUS and YES or the front speakers set to LARGE and SMALL alternatively and let your ears judge which sounds best. If you’re having problems, the easiest option is to route all the bass sounds to the subwoofer by selecting SMALL for the front speakers.

X.OVER

• Default setting:

100Hz

This setting decides the cutoff between bass sounds playing back from the speakers selected as LARGE, or the subwoofer, and bass sounds playing back from those selected as

SMALL. It also decides where the cutoff will be for bass sounds in the LFE channel.

• For more on selecting the speaker sizes, see Speaker

Setting on page 28.

1

Select ‘Manual SP Setup’ from the Home Menu.

2

Select ‘X.OVER’ from the Manual SP Setup menu.

2.Manual SP Setup a.Speaker System b.Speaker Setting c.X.OVER

d.Channel Level e.Speaker Distance

2c.X.OVER

Frequency 100Hz

Return Return

3

Choose the frequency cutoff point.

Frequencies below the cutoff point will be sent to the subwoofer (or LARGE speakers).

4

When you’re finished, press RETURN.

You return to the Manual SP Setup menu.

VSX-S300_SYXCN_En.book 29 ページ 2011年4月8日 金曜日 午後8時10分

The Home Menu

Channel Level

Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor when setting up a home theater system.

1

Select ‘Manual SP Setup’ from the Home Menu.

2

Select ‘Channel Level’ from the Manual SP Setup menu.

2.Manual SP Setup a.Speaker System b.Speaker Setting c.X.OVER

d.Channel Level e.Speaker Distance

2d.Channel Level

Test Tone Manual

Return

Enter:Next



Return

3

Select a setup option.

Manual – Move the test tone manually from speaker to speaker and adjust individual channel levels.

Auto – Adjust channel levels as the test tone moves from speaker to speaker automatically.

4

Confirm your selected setup option.

The test tones will start after you press

ENTER. After the volume increases to the reference level, test tones will be output.

2d.Channel Level

Test Tone [ Manual ]

Please Wait . . .20

Caution

Loud test tones

will be output.



Return

5

Adjust the level of each channel using

/.

If you selected Manual, use

/ to switch speakers. The

Auto setup will output test tones in the order shown onscreen:

2d.Channel Level

Front L

Center

Front R

Surround R

Surr. Back R

Surr. Back L

Surround L

Subwoofer

0dB

[ 0dB]

[ 0dB]

[ 0dB]

[ ––– ]

[ ––– ]

[ 0dB]

[ 0dB]

Return

Adjust the level of each speaker as the test tone is emitted.

Note

• If you are using a Sound Pressure Level (SPL) meter, take the readings from your main listening position and adjust the level of each speaker to 75 dB SPL (C-weighting/slow reading).

• The subwoofer test tone is output at low volumes. You may need to adjust the level after testing with an actual soundtrack.

6

When you’re finished, press RETURN.

You return to the Manual SP Setup menu.

Speaker Distance

For good sound depth and separation from your system, you need to specify the distance of your speakers from the listening position. The receiver can then add the proper delay needed for effective surround sound.

1

Select ‘Manual SP Setup’ from the Home Menu.

2

Select ‘Speaker Distance’ from the Manual SP Setup menu.

2.Manual SP Setup a.Speaker System b.Speaker Setting c.X.OVER

d.Channel Level e.Speaker Distance

2e.Speaker Distance

Front L

Center

Front R

Surround R

Surr. Back R

Surr. Back L

Surround L

Subwoofer

3.0 m

[ 3.0 ]

[ 3.0 ]

[ 3.0 ]

[ –––– ]

[ –––– ]

[ 3.0 ]

[ 3.0 ]

Return

Return

3

Adjust the distance of each speaker using

/.

You can adjust the distance of each speaker in 0.1 m increments.

4

When you’re finished, press RETURN.

You return to the Manual SP Setup menu.

29

En

30

En

VSX-S300_SYXCN_En.book 30 ページ 2011年4月8日 金曜日 午後8時10分

The Home Menu

The Pre Out Setting

Specify either using the surround back speaker or the front height speaker connection with the

PRE OUT SURR BACK/

FRONT HEIGHT outputs. An additional amplifier is required for the speaker connection.

• Default setting:

Surr. Back

1

Select ‘Pre Out Setting’ from the Home Menu.

Home Menu

1 . Auto MCACC

2 . Manual SP Setup

3 . Pre Out Setting

4 . Input Assign

5 . HDMI Setup

6 . Auto Power Down

7 . FL Demo Mode

3.Pre Out Setting

Pre Out Surr. Back

Return

2

Select which speaker to connect to the PRE OUT SURR

BACK/FRONT HEIGHT outputs using

/.

Surr. Back – Connect the surround back speaker.

Height – Connect the front height speaker.

3

When you’re finished, press RETURN.

You return to the Home Menu.

The Input Assign menu

The composite video input terminal is assigned to

ANALOG

AUX under factory settings, but this can be changed to

DIGITAL AUX or CD input.

1

Select ‘Input Assign’ from the Home Menu.

Home Menu

1 . Auto MCACC

2 . Manual SP Setup

3 . Pre Out Setting

4 . Input Assign

5 . HDMI Setup

6 . Auto Power Down

7 . FL Demo Mode

2

Select ‘Composite Input’ from the Input Assign menu.

4.Input Assign a.Composite Input

4a.Composite Input

I n p u t ANALOG AUX

Return Return

3

Select the desired input option for the composite video input terminal.

Select between ANALOG AUX, DIGITAL AUX, CD or OFF.

• Use

/ and ENTER to do this.

• Make sure you have connected the audio from the component to the corresponding inputs on the rear of the receiver.

4

When you’re finished, press RETURN.

You return to the Input Assign menu.

The Auto Power Down menu

Set to automatically turn off the receiver after a specified time has passed (when the power has been on with no operation for several hours).

• Default setting:

6H

1

Select ‘Auto Power Down’ from the Home Menu.

Home Menu

1 . Auto MCACC

2 . Manual SP Setup

3 . Pre Out Setting

4 . Input Assign

5 . HDMI Setup

6 . Auto Power Down

7 . FL Demo Mode

6.Auto

Power Down

6H

Return

2

Specify the amount of time to allow before the power is turned off (when there has been no operation).

• You can select 2, 4 or 6 hours, or OFF (if no automatic shutoff is desired).

3

When you’re finished, press RETURN.

You return to the Home Menu.

The FL Demo Mode menu

Set whether or not various demos are to be shown on the front panel display.

1

Select ‘FL Demo Mode’ from the Home Menu.

Home Menu

1 . Auto MCACC

2 . Manual SP Setup

3 . Pre Out Setting

4 . Input Assign

5 . HDMI Setup

6 . Auto Power Down

7 . FL Demo Mode

7.FL Demo Mode

FL Demo ON

Return

2

Choose ON or OFF for the demo display.

3

When you’re finished, press RETURN.

You return to the Home Menu.

VSX-S300_SYXCN_En.book 31 ページ 2011年4月8日 金曜日 午後8時10分

Control with HDMI function

Chapter 7:

Control with HDMI function

Synchronized operations below with a Control with HDMIcompatible Pioneer TV or Blu-ray Disc player or with a component of another make that supports the Control with

HDMI functions are possible when the component is connected to the receiver using an HDMI cable.

• Synchronized amp mode

The receiver’s volume can be set and the sound can be muted using the TV’s remote control.

• Power synchronization with TV

• Automatic switching of inputs

The receiver’s input switches over automatically when the

TV’s input is changed or a Control with HDMI-compatible component is played.

Important

• With Pioneer devices, the

Control with HDMI functions are referred to as “KURO LINK”.

• You cannot use this function with components that do not support Control with HDMI.

• We only guarantee this receiver will work with Pioneer made Control with HDMI-compatible components and components of other makes that support the Control with HDMI function. However, we do not guarantee that all synchronized operations will work with components of other makes that support the Control with HDMI function.

• Use a High Speed HDMI

®

cable when you want to use the

Control with HDMI function. The Control with HDMI function may not work properly if a different type of HDMI cable is used.

• For details about concrete operations, settings, etc., refer to also the operating instructions for each component.

Making Control with HDMI connections

You can use synchronized operation for a connected TV and up to four other components.

• Be sure to connect the TV’s audio cable to the audio input of this unit. When the TV and receiver are connected by

HDMI connections, if the TV supports the HDMI Audio

Return Channel function, the sound of the TV is input to the receiver via the HDMI terminal, so there is no need to connect an audio cable. In this case, set ARC at HDMI

Setup to ON (see HDMI Setup below).

For details, see Connecting using HDMI on page 13.

Important

• When connecting this system or changing connections, be sure to switch the power off and disconnect the power cord from the wall socket.

After completing all connections, connect the power cords to the wall socket.

• After this receiver is connected to an AC outlet, a 2 second to 10 second HDMI initialization process begins.

You cannot carry out any operations during initialization.

The HDMI indicator on the display unit blinks during initialization, and you can turn this receiver on once it has stopped blinking.

• To get the most out of this function, we recommend that you connect your HDMI component not to a TV but rather directly to the HDMI terminal on this receiver.

• While the receiver is equipped with four HDMI inputs, the

Control with HDMI function can only be used with up to three DVD or Blu-ray Disc players or up to three DVD or

Blu-ray Disc recorders.

HDMI Setup

You must adjust the settings of this receiver as well as the connected Control with HDMI-compatible components in order to make use of the

Control with HDMI function. For more information see the operating instructions for each component.

1

Switch on the receiver and your TV.

Press

RECEIVER to switch on.

2

Switch the TV input to the input that connects this receiver to the TV through the corresponding composite cable.

3

Press RECEIVER , then press HOME MENU.

The Home Menu appears on your TV. Use

/// and

ENTER on the remote control to navigate through the screens and select menu items. Press RETURN to confirm and exit the current menu.

• Press HOME MENU at any time to exit the Home Menu.

4

Select ‘HDMI Setup’ from the Home Menu.

Home Menu

1 . Auto MCACC

2 . Manual SP Setup

3 . Pre Out Setting

4 . Input Assign

5 . HDMI Setup

6 . Auto Power Down

7 . FL Demo Mode

5.HDMI Setup

Control ON

ARC [ OFF ]

Return

5

Select the ‘Control’ setting you want.

Choose whether to set this unit’s

Control with HDMI function ON or OFF. You will need to set it to ON to use the

Control with HDMI function.

When using a component that does not support the Control with HDMI function, set this to OFF.

ON – Enables the Control with HDMI function. When this unit’s power is turned off and you have a supported source begin playback while using the Control with

HDMI function, the audio and video outputs from the

HDMI connection are output from the TV.

OFF – The Control with HDMI is disabled. Synchronized operations cannot be used. When this unit’s power is turned off, audio and video of sources connected via

HDMI are not output.

31

En

32

En

VSX-S300_SYXCN_En.book 32 ページ 2011年4月8日 金曜日 午後8時10分

Control with HDMI function

6

Select the ‘ARC’ setting you want.

When a TV supporting the HDMI Audio Return Channel function is connected to the receiver, the sound of the TV can be input via the HDMI terminal.

ON – The TV’s sound is input via the HDMI terminal. This can only be selected when

Control is set to ON.

OFF – The TV’s sound is input from the audio input terminals other than HDMI inputs.

7

When you’re finished, press RETURN.

You return to the Home Menu.

Before using synchronization

Once you have finished all connections and settings, you must:

1

Put all components into standby mode.

2

Turn the power on for all components, with the power for the TV being turned on last.

3

Choose the HDMI input to which the TV is connected to this receiver, and see if video output from connected components displays properly on the screen or not.

4

Check whether the components connected to all HDMI inputs are properly displayed.

About synchronized operations

The Control with HDMI-compatible component connected to the receiver operates in sync as described below.

• Synchronized amp mode

From the menu screen of the

Control with HDMIcompatible TV, set audio to be played through this receiver, and the receiver will switch to the synchronized amp mode.

-

When in the synchronized amp mode, the synchronized amp mode is canceled when the receiver’s power is turned off. To turn the synchronized amp mode back on, set audio to be played through the receiver from the TV’s menu screen, etc. This receiver will power up and switch to the synchronized amp mode.

When in the synchronized amp mode, the synchronized amp mode is canceled if an operation that produces sound from the TV is performed from the TV’s menu screen, etc.

-

When the synchronized amp mode is canceled, the receiver’s power turns off if you were viewing an HDMI input or a TV program on the TV.

• Power synchronization with TV

-

When the TV’s power is set to standby, the receiver’s power is also set to standby. (Only when the input for a component connected to the receiver by HDMI connection is selected or when watching the TV.)

• Automatic switching of inputs

The receiver’s input switches automatically when the

Control with HDMI-compatible component is played.

The receiver’s input switches automatically when the

TV’s input is switched.

The synchronized amp mode remains in effect even if the receiver’s input is switched to a component other than one connected by HDMI.

About connections with a product of a different brand that supports the Control with HDMI function

The synchronized operations below can be used when the receiver’s Control with HDMI function is connected to a TV of a brand other than Pioneer that supports the Control with

HDMI function. (Depending on the TV, however, some of the

Control with HDMI functions may not work.)

• When the TV’s power is set to standby, the receiver’s power is also set to standby. (Only when the input for a component connected to the receiver by HDMI connection is selected or when watching the TV)

• The sound of TV programs or an external input connected to the TV can also be output from the speakers connected to the receiver. (If the TV does not support the HDMI

Audio Return Channel function, this requires connection of an optical digital cable, etc., in addition to the HDMI cable.)

The synchronized operations below can be used when the receiver’s Control with HDMI function is connected to a player or recorder of a brand other than Pioneer that supports the

Control with HDMI function.

• When playback starts on the player or recorder, the receiver’s input switches to the HDMI input to which that component is connected.

See the Pioneer website for the latest information on the models of non-Pioneer brands and products that support the

Control with HDMI function.

Cautions on the Control with HDMI function

• Connect the TV and components (Blu-ray Disc player, etc.) directly to this receiver. Interrupting a direct connection with other amps or an AV converter (such as an HDMI switch) can cause operational errors.

• When the receiver’s Control is turned ON, even if the receiver’s power is in the standby mode, it is possible to output the audio and video signals from a player via HDMI to the TV without producing sound from the receiver, but only when a Control with HDMI-compatible component

(Blu-ray Disc player, etc.) and compatible TV are connected. In this case, the receiver’s power turns on and the power and HDMI indicators light.

VSX-S300_SYXCN_En.book 33 ページ 2011年4月8日 金曜日 午後8時10分

Additional information

Chapter 8:

Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Take a look at the other components and electrical appliances being used, because sometimes the problem may lie there. If the trouble isn’t sorted out even after going through the checks below, ask your nearest Pioneer authorized independent service company to carry out repair work.

• If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions.

General

The power does not turn on.

 Disconnect the power plug from the outlet, and insert again.

 Make sure there are no loose strands of speaker wire touching the rear panel. This could cause the receiver to shut off automatically.

The receiver suddenly switches off.

 When the Auto Power Down function is working, the power will automatically turn off if the receiver has not operated for several hours. Check the setting for the Auto Power Down function (see The Auto Power Down menu on page 30).

 After about a minute (you won’t be able to switch the unit on during this time), switch the receiver back on. If the message persists, call a Pioneer authorized independent service company.

The power suddenly turns on or off, or the input suddenly changes (When the Control with HDMI is ON).

 This happens because of the synchronized operation due to the Control with HDMI function. If synchronized operations are not needed, set the Control with HDMI to OFF (see HDMI

Setup on page 31).

OVERHEAT shows in the display and the power turns off.

 The temperature within the unit has exceeded the allowable value. Try moving the unit for better ventilation (see page 2).

 Lower the volume level.

TEMP shows in the display and the volume level drops.

 The temperature within the unit has exceeded the allowable value. Try moving the unit for better ventilation (see page 2).

 Lower the volume level.

No sound is output when an input function is selected.

 Use VOL +/– to turn up the volume.

 Press MUTE to turn muting off.

 Make sure the component is connected correctly (refer to

Connecting your equipment on page 9).

 Check the audio output settings of the source component.

 Refer to the instruction manual supplied with the source component.

No image is output when an input function is selected.

 Make sure the component is connected correctly (refer to

Connecting your equipment on page 9).

 Use the same type of video cables for the source component and TV to connect to this receiver (see About video outputs

connection on page 12).

 Check The Input Assign menu on page 30 to make sure you’re assigned the correct input.

 The video input selected on the TV monitor is incorrect. Refer to the instruction manual supplied with the TV.

No sound from subwoofer.

 When using a powered subwoofer, make sure the subwoofer is switched on.

 If the subwoofer has a volume knob, make sure it’s turned up.

 The Dolby Digital or DTS source you are listening to may not have an LFE channel.

 Switch the subwoofer setting in Speaker Setting on page 28 to

YES or PLUS.

 Switch the LFE ATT (LFE Attenuate) on page 25 to 0dB or -5dB.

No sound from surround or center speakers.

 Connect the speakers properly (refer to page 10).

 Refer to Speaker Setting on page 28 to check the speaker settings.

 Refer to Channel Level on page 29 to check the speaker levels.

The Phase Control feature doesn’t seem to have an audible effect.

 If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is set to the highest frequency setting. If there is a PHASE setting on your subwoofer, set it to 0º (or depending on the subwoofer, the setting where you think it has the best overall effect on the sound).

 Make sure the speaker distance setting is correct for all speakers (see Speaker Distance on page 29).

Considerable noise in radio broadcasts.

 Connect the antenna (page 14) and adjust the position for best reception.

 Route any loose cables away from the antenna terminals and wires.

 Fully extend the FM wire antenna, position for best reception, and secure to a wall (or connect an outdoor FM antenna).

 Connect an additional internal or external AM antenna

(page 15).

 Turn off equipment causing interference or move it away from the receiver (or move antennas farther away from equipment causing noise).

Broadcast stations cannot be selected automatically.

 Connect an outdoor antenna (refer to page 15).

Noise during playback of a cassette deck.

 Move the cassette deck away from your receiver, until the noise disappears.

No sound is output or a noise is output when software with

DTS is played back.

 Make sure the player’s settings are correct and/or the DTS signal out is on. Refer to the instruction manual supplied with the DVD player.

There seems to be a time lag between the speakers and the output of the subwoofer.

 See Automatically setting up for surround sound (MCACC) on page 16 to set up your system again using MCACC (this will automatically compensate for a delay in the subwoofer output).

After using the Auto MCACC setup, the speaker size setting

(LARGE or SMALL) is incorrect.

 Low-frequency noise could have been caused by an air conditioner or motor. Switch off all appliances in the room and rerun the Auto MCACC setup.

33

En

VSX-S300_SYXCN_En.book 34 ページ 2011年4月8日 金曜日 午後8時10分

Additional information

34

En

Can’t operate the remote control.

 Replace the batteries (refer to page 8).

 Operate within 7 m, 30º of the remote sensor (refer to page 8).

 Remove the obstacle or operate from another position.

 Avoid exposing the remote sensor on the front panel to direct light.

The display is dark or off.

 Press DIMMER repeatedly to return to the default.

The front panel display switches over for no apparent reason to various different displays.

 This happens because the demo display is in operation. To turn off the demo display, press any button to go back to the original display, or set the FL Demo Mode to OFF (see The FL

Demo Mode menu on page 30).

The Bluetooth wireless technology device cannot be connected or operated. Sound from the

Bluetooth wireless technology device is not emitted or the sound is interrupted.

 Check that no object that emits electromagnetic waves in the

2.4 GHz band (microwave oven, wireless LAN device or

Bluetooth wireless technology apparatus) is near the unit. If such an object is near the unit, set the unit far from it. Or, stop using the object emitting the electromagnetic waves.

 Check that the Bluetooth wireless technology device is not too far from the unit and that obstructions are not set between the

Bluetooth wireless technology device and the unit. Set the

Bluetooth wireless technology device and the unit so that the distance between them is less than about 10 m and no obstructions exist between them.

 Check that the Bluetooth ADAPTER and the ADAPTER PORT terminal of the unit are correctly connected.

 The Bluetooth wireless technology device may not be set to the communication mode supporting the Bluetooth wireless technology. Check the setting of the Bluetooth wireless technology device.

 Check that pairing is correct. The pairing setting was deleted from this unit or the Bluetooth wireless technology device.

Reset the pairing.

 Check that the profile is correct. Use a Bluetooth wireless technology device that supports A2DP profile and AVRCP profile.

HDMI

No picture or sound.

 If the problem still persists when connecting your HDMI component directly to your monitor, please consult the component or monitor manual or contact the manufacturer for support.

No picture.

 Video signals that are input from the analog video terminal will not output from the HDMI terminal. Signals that are input from the HDMI terminal will not output from the analog video terminal. Be consistent with the type of cable between input and output.

 Depending in the output settings of the source component, it may be outputting a video format that can’t be displayed.

Change the output settings of the source, or connect using the composite video jacks.

 This receiver is HDCP-compatible. Check that the components you are connecting are also HDCP-compatible. If they are not, please connect them using the composite video jacks.

 Depending on the connected source component, it’s possible that it will not work with this receiver (even if it is HDCPcompatible). In this case, connect using the composite video jacks between source and receiver.

 If video images do not appear on your TV, try adjusting the resolution, Deep Color or other setting for your component.

 To output signals in Deep Color, use an HDMI cable (High

Speed HDMI

®

Cable) to connect this receiver to a component or TV with the Deep Color feature.

The OSD screen (Home Menu, etc.) isn’t displayed.

 The OSD will not appear if you have connected using the

HDMI output to your TV. Use composite connections when setting up the system.

No sound, or sound suddenly ceases.

 Check that the Audio Parameter setting is set to HDMI AMP/

THRU (refer to page 24).

 If the component is a DVI device, use a separate connection for the audio.

 HDMI format digital audio transmissions require a longer time to be recognized. Due to this, interruption in the audio may occur when switching between audio formats or beginning playback.

 Turning on/off the device connected to this unit’s HDMI OUT terminal during playback, or disconnecting/connecting the

HDMI cable during playback, may cause noise or interrupted audio.

Synchronized operation not possible using Control with

HDMI function.

 Check the HDMI connections.

 The cable may be damaged.

 Select ON for the Control with HDMI setting (see HDMI Setup on page 31).

 Turn the TV’s power on before turning on this receiver’s power.

 Set the TV side Control with HDMI setting to on (see TV’s operating instructions).

Important information regarding the HDMI connection

There are cases where you may not be able to route HDMI signals through this receiver (this depends on the HDMI equipped component you are connecting-check with the manufacturer for HDMI compatibility information).

If you aren’t receiving HDMI signals properly through this receiver (from your component), please try the following configuration when connecting up.

Configuration

Connect your HDMI-equipped component directly to the display using an HDMI cable. Then use the most convenient connection (digital is recommended) for sending audio to the receiver. See the operating instructions for more on audio connections. Set the display volume to minimum when using this configuration.

Note

• Depending on the component, audio output may be limited to the number of channels available from the connected display unit (for example audio output is reduced to 2 channels for a monitor with stereo audio limitations).

• If you want to switch the input source, you’ll have to switch functions on both the receiver and your display unit.

• Since the sound is muted on the display when using the

HDMI connection, you must adjust the volume on the display every time you switch input sources.

VSX-S300_SYXCN_En.book 35 ページ 2011年4月8日 金曜日 午後8時10分

Additional information

Resetting the main unit

Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.

1

Switch the receiver into standby.

2

Press and hold INPUT SELECTOR button on the front panel for more than five seconds, and then press BD button on the remote control.

3

When you see RESET? appear in the display, press

AUTO/DIRECT.

OK? shows in the display.

4

Press ALC/STANDARD to confirm.

OK appears in the display to indicate that the receiver has been reset to the factory default settings.

Important

• If the Control with HDMI function is set to ON, you may not be able to reset the unit. In this case, reset either by turning

OFF the Control with HDMI function, or by putting the unit into standby mode by turning off the power of all the connected devices, and resetting after the

HDMI indicator on the front panel turns off.

Cleaning the unit

• Use a polishing cloth or dry cloth to wipe off dust and dirt.

• When the surface is dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water, and wrung out well, and then wipe again with a dry cloth.

Do not use furniture wax or cleansers.

• Never use thinners, benzine, insecticide sprays or other chemicals on or near this unit, since these will corrode the surface.

Specifications

Audio section

Rated power output

Front, Center, Surround

. . . . . . . . . . . . . . . . . . 100 W per channel (1 kHz, 4

Ω, 1 %)

Subwoofer . . . . . . . . . . . . . . . . . . . . 100 W (30 Hz, 4

Ω, 1 %)

Total Harmonic Distortion

. . . . . . . . . . . . . . . . 0.06 % (20 Hz to 20 kHz, 8

Ω, 50 W/ch)

Frequency response (ANALOG Pure Direct mode)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Hz to 20 kHz dB

Guaranteed speaker impedance . . . . . . . . . . . . . . 4

Ω to 16 Ω

Input (Sensitivity/Impedance) . . . . . . . . . . . . . . 200 mV/47 k

Ω

Signal-to-Noise Ratio (IHF, short circuited, A network)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 dB

Video section

Signal level (Composite) . . . . . . . . . . . . . . . . . . .1 Vp-p (75

Ω)

Tuner section

Frequency Range (FM) . . . . . . . . . . . . . .87.5 MHz to 108 MHz

Antenna Input (FM) . . . . . . . . . . . . . . . . . . . 75

Ω unbalanced

Frequency Range (AM) . . . . . . . . . . . . . .531 kHz to 1602 kHz

Antenna (AM) . . . . . . . . . . . . . . . . . . . . . . . . . . . Loop antenna

Digital In/Out section

HDMI terminal . . . . . . . . . . . . . . . . . . . . . . . . . Type A (19-pin)

HDMI output type . . . . . . . . . . . . . . . . . . . . . . . . . .5 V, 100 mA

ADAPTER PORT terminal . . . . . . . . . . . . . . . . . . .5 V, 100 mA

Miscellaneous

Power Requirements . . . . . . .AC 220 V to 230 V, 50 Hz/60 Hz

Power Consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 W

In standby . . . . . 0.5 W ( Control with HDMI function: ON)

0.45 W ( Control with HDMI function: OFF)

Dimensions . . . . . . . 435 mm (W) x 85 mm (H) x 317 mm (D)

Weight (without package) . . . . . . . . . . . . . . . . . . . . . . . .4.2 kg

Furnished Parts

Microphone (for Auto MCACC setup) . . . . . . . . . . . . . . . . . . .1

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Dry cell batteries (AAA size IEC R03) . . . . . . . . . . . . . . . . . . .2

AM loop antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Power cord

Quick start guide

Safety Brochure

These operating instructions

Note

• The specifications are applicable when the power supply is 230 V/50 Hz.

• Specifications and the design are subject to possible modifications without notice, due to improvements.

Manufactured under license from Dolby Laboratories. “Dolby”,

“Pro Logic”, “Surround EX”, and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license under U.S. Patent #’s: 5,451,942;

5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535;

7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks, & DTS-HD, DTS-HD Master Audio, and the DTS logos are trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.

iPod is trademarks of Apple Inc., registered in the U.S. and other countries.

35

En

VSX-S300_SYXCN_En.book 36 ページ 2011年4月8日 金曜日 午後8時10分

http://www.pioneer.co.uk

http://www.pioneer.eu

PIONEER CORPORATION

1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan

PIONEER ELECTRONICS (USA) INC.

P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404

PIONEER ELECTRONICS OF CANADA, INC.

340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901, 905-479-4411

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

5 Arco Lane, Heatherton, Victoria, 3202, Australia, TEL: (03) 9586-6300

PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.

Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270

K002_B3_En

© 2011 PIONEER CORPORATION.

All rights reserved.

<6517-00000-033-0S>

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement