mobile digital video recorder user guide

Add to my manuals
63 Pages

advertisement

mobile digital video recorder user guide | Manualzz

MOBILE DIGITAL VIDEO RECORDER

USER GUIDE

Ver. C4K-V1.06

 Thank you for purchasing C4K Series Mobile DVR.

 Before using the Digital Video Recorder, please ensure that you read and understand the User Guide.

 Please store the User Guide at an easily accessible location.

 Before connecting and installing any third party cameras, monitors, alarms and computers, please refer to the appropriate instruction manual for proper operation.

SAFETY PRECAUTIONS

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product‟s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

1 MOBILE DIGITAL VIDEO RECORDER

Contents

Contents ................................................................................................... 2

Disclaimer ................................................................................................. 4

Warning ..................................................................................................... 4

Caution ..................................................................................................... 6

Preventing Malfunctions ......................................................................... 6

Package Contents .................................................................................. 7

I.CONTROLS .............................................................................................. 8

1. Front Panel....................................................................................................... 8

2. Rear Panel Connectors ................................................................................. 11

3. Remote Controller ........................................................................................ 12

4. Virtual Keypad for Mouse Control. ............................................................. 13

II.INSTALLATION & CONNECTIONS ....................................................... 14

1.

Camera, Monitor, Microphone, Alarm sensor and Power cord .............. 14

2. PC System Requirements for Network Connection. .................................. 15

III.QUICK SETUP ....................................................................................... 16

1.

RECORD ......................................................................................................... 17

2.

AUDIO IN ....................................................................................................... 17

3.

POST RECORDING ......................................................................................... 17

4.

RUN ADVANCED ........................................................................................... 17

IV. LIVE VIEWING .................................................................................... 18

1. Display Overview.......................................................................................... 18

2. Multi screen Display and Sequencing........................................................ 19

2.1 . Full Screen Display .................................................................................................. 19

2.2 . Multi-screen Display and Sequencing Display. .................................................... 19

3.

Zooming ........................................................................................................ 19

V. OPERATION ........................................................................................ 20

1. Main Menu Overview ................................................................................... 20

2. Display Option .............................................................................................. 21

2.1. Display Setup .............................................................................................................. 21

2.2. Sequential Setup (Auto Sequence) .......................................................................... 22

2.3. OSD Setup ................................................................................................................... 22

3. Camera Setup............................................................................................... 23

4. Recording ...................................................................................................... 26

4.1. General Settings ......................................................................................................... 26

2 MOBILE DIGITAL VIDEO RECORDER

4.3. Chart (Schedule Recording) ..................................................................................... 28

5. Device ........................................................................................................... 30

5.1. GENERAL ..................................................................................................................... 30

5.2. ALARM ........................................................................................................................ 31

5.3. SHOCK SENSOR .......................................................................................................... 32

5.4. SPEED .......................................................................................................................... 33

6. Network Setup .............................................................................................. 34

6.1. IP setup ....................................................................................................................... 34

6.2. Wireless ....................................................................................................................... 35

7. System Setup ................................................................................................. 36

7.1. General....................................................................................................................... 36

7.2. Time ............................................................................................................................ 37

7.3. Account ...................................................................................................................... 38

7.4. DISK ............................................................................................................................. 39

7.5. UPDATE. ....................................................................................................................... 40

7.6. INFO ............................................................................................................................ 41

7.7. MOBILE ........................................................................................................................ 42

VI.PAN/TILT/ZOOM CONTROL .............................................................. 43

1. P.T.Z. Menu .................................................................................................... 43

2. Preset & Tour .................................................................................................. 44

3. Custom Functions ......................................................................................... 44

4. PTZ Camera Model - PAN/TILT/ZOOM Camera List ................................... 45

VII.SEARCH/PLAYBACK ......................................................................... 47

1. Time Search .................................................................................................. 47

2. Log List Search/Alarm, Motion Search ....................................................... 48

VIII.BACKUP ............................................................................................ 49

1. USB Memory Stick / External USB HDD Backup.......................................... 49

2. Back up Range Setup .................................................................................. 50

IX. C4K Viewer ....................................................................................... 51

1. Installation ..................................................................................................... 51

2. Software ......................................................................................................... 54

X.SPECIFICATION ................................................................................... 60

3 MOBILE DIGITAL VIDEO RECORDER

Disclaimer

 The information in this manual is believed to be accurate and reliable as of the date of publication. The information contained herein is subject to change without notice.

Revisions or New editions to this publication may be issued to incorporate such change

 We make no warranties for damages resulted from corrupted or lost data due to a mistaken operation or malfunction of the Digital Video Recorder, the software, the hard drives, personal computers, peripheral devices, or unapproved/unsupported devices.

Warning

 Do not cover the ventilation opening or slots on the outer casing. To prevent the appliance from overheating, provide at least two inches of air space around the vent and the slots. Do not place the product in direct sunlight.

 Do not drop metallic parts through slots. This could permanently damage the Digital

Video Recorder. Immediately turn the DVR‟s power off or unplug the power cord from the power outlet. Contact a qualified service personnel authorized by your equipment distributor

 Do not attempt to disassemble or alter any part of the equipment that is not expressly described in this guide. Disassembly or alteration may result in high voltage electrical shock. Qualified service personnel authorized by your equipment distributor should conduct internal inspections, alterations and repairs.

 Stop operating the equipment immediately if it emits smoke or noxious fumes. Failure to do so may result in fire or electrical shock. Immediately turn the DVR‟s power off, remove the power cable from the power outlet. Confirm that smoke and fume emissions have ceased. Please consult your DVR distributor.

 Stop operating the equipment if a heavy object is dropped or the casing is damaged.

Do not strike or shake. Failure to do so may result in fire or electrical shock.

Immediately turn the DVR‟s power off or unplug the power cord from the power outlet.

Please consult your DVR distributor.

 Do not allow the equipment come into contact with, or become immersed in, water or other liquids. Do not allow liquids to enter the interior. The DVR has not been waterproofed. If the exterior comes into contact with liquids or salt air, wipe it dry

4 MOBILE DIGITAL VIDEO RECORDER

with a soft, absorbent cloth. In the event that the water or other foreign substances enter the interior, immediately turn the DVR‟s Power off or unplug the power cord from the power outlet. Continued use of the equipment may result in fire or electrical shock. Please consult your DVR distributor.

 Do not use substances containing alcohol, benzene, thinners or other flammable substances to clean or maintain the equipment. The use of these substances may lead to fire. Use a dry cloth on a regular periodic basis and wipe away the dust and dirt that collects on the device. In dusty, humid or greasy environments, the dust that collects around the ventilation or the slots on the outer casing over long periods of time may become saturated with humidity and short-circuit, leading to fire.

 Do not cut, damage, alter or place heavy items on the power cord. Any of these actions may cause an electrical short circuit, which may lead to fire or electrical shock.

 Do not handle the device or power cord if your hands are wet. Handling it with wet hands may lead to electrical shock. When unplugging the cord, ensure that you hold the solid portion of the plug. Pulling on the flexible portion of the cord may damage or expose the wire and insulation, creating the potential for fires or electrical shocks.

 Use only the recommended power accessories. Use of power sources not expressly recommended for this equipment may lead to overheating, distortion of the equipment, fire, electrical shock or other hazards.

 Do not place the batteries near a heat source or expose them to direct flame or heat.

Neither should you immerse them in water. Such exposure may damage the batteries and lead to the leakage of corrosive liquids, fire, electrical shock, explosion or serious injury.

 Do not attempt to disassemble, alter or apply heat to the batteries. There is serious risk of injury due to an explosion. Immediately flush with water any area of the body, including the eyes and mouth, or clothing that comes into contact with the inner contents of the battery. If the eyes or mouth contact these substances, immediately flush with water and seek medical assistance from a medical professional.

 Avoid dropping or subjecting the batteries to severe impacts that could damage the casings. It could lead to leakage and injury.

 Do not short-circuit the battery terminals with metallic objects, such as key holders. It could lead to overheating, burns and other injuries.

 The supplied power supply and power cord are designed for exclusive use with the

Digital Video Recorder. Do not use it with other products or batteries. There is a risk of fire and other hazards.

5 MOBILE DIGITAL VIDEO RECORDER

Caution

 Do not operate the appliance beyond its specified temperature, humidity or power source ratings. Do not use the appliance in an extreme environment where there is high temperature or high humidity. Use the device at temperatures within -20°C -

+60°C (-4°F - 140°F) and humidity below 90 %. The normal operating power source for this device is DC 12/24V.

Preventing Malfunctions

 Avoid Strong Magnetic Fields. Never place the DVR in close Proximity to electric motors or other equipment generating strong electromagnetic fields. Exposures to strong magnetic fields may cause malfunctions or corrupt image data.

 Avoid Condensation Related Problems. Moving the equipment rapidly between hot and cold temperatures may cause condensation (water droplets) to form on its external and internal surfaces. You can avoid this by placing the equipment in an airtight, resalable plastic bag and letting it adjust to temperature changes slowly before removing it from the bag.

 If Condensation forms inside the Digital Video Recorder. Stop using the equipment immediately if you detect condensation. Continued use may damage the equipment.

Remove the power cord from the power outlet and wait until the moisture evaporates completely before resuming use.

CAUTION

- Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries

According to the Instructions.

- The socket-outlet shall be installed near the equipment and shall be easily

accessible.

6 MOBILE DIGITAL VIDEO RECORDER

Package Contents

Please check the package and contents for visible damage. If any components are damaged or missing, do not attempt to use the unit, contact the supplier immediately. If the unit must be returned, it must be shipped in the original packing box.

Model PMR-C4004 (Standard Package)

Function - 4CH 120fps(2CIF)

- 2D VGA, 1 audio

- Recording

Contents - DVR board with case(type1)

- 4pin power cable

- 8pin sensor cable

- CD(manual, media viewer, quick guide)

- Remote controller

- 12V5A Adapter&power cord

Option

PMR-C4004 (Mobile Package)

- 4CH 120fps(2CIF)

- 2D VGA, 1 audio

- GPS

- 3G Connectivity via USB Type Modem

- DVR board with case (type2)

- 4pin power cable

- 8pin sensor cable

- Screw 4 ea

- Rack guide 2 ea

- Rack guide screw 6ea

- CD(manual, media viewer, quick guide)

- Remote controller

- Cigar Lighter Plug and Cable

- GPS Antenna & GPS/G-Sensor PCB

7 MOBILE DIGITAL VIDEO RECORDER

I.CONTROLS

1. Front Panel

1-1. Mode Indicators : 4 LEDs display the status of the Device.

Power, Recording (Green), HDD Activated(Red), Networking (Yellow)

1-2. Control Switch and Buttons

Power Switch : Turns on / off the power of device

8 MOBILE DIGITAL VIDEO RECORDER

Reboot Button : Reboots the device

Menu Button : Enters Menu

Adjustment Buttons : Adjust value of selected item in menu

Playback / Record Control Buttons

1) Recording / Standby Mode

: [CLR] – Clears/Displays the OSD Information on Screen

: [Log] – Enter to Log History

: [Enter] – Enter to Menu or Save Settings

: [Rec] – Starts or Stops Recording

: [Time Search] – Enters to “Time Search Playback” Menu

: [Schedule Rec] – Triggers Schedule Recording when Pushed for

Over 3 Seconds

2) Playback Mode

: [CLR] – Exits Playback mode

: [Play/Pause] – Plays and Pauses Video

: [Display Mode] – Displays All Channels

: [RWD] – Rewinds Recording (5 Level Speed Adjustable Using [RWD] and [FF] Button)

: [Stop] – Stops and Exits Playback Mode

: [FF] –Fast Forwards Recording (5 Level Speed Adjustable Using

[RWD] and [FF] Button)

9 MOBILE DIGITAL VIDEO RECORDER

3) Menu

: [CLR] – Goes Back to Previous Menu Without Saving

: [Arrow Keys] – Moves to Pointed Direction

: [Enter] – Enters to Selected Menu or Sub-menu

1-3. Others

1) USB Port

: For USB Backup Storage, USB-type 3G Modem or Mouse

2) Remote Control Signal Receiver

! Do not block the receiver port on the unit. Doing so may cause the remote controller to function improperly. !

10 MOBILE DIGITAL VIDEO RECORDER

1

2. Rear Panel Connectors

1) GPS : GPS Antenna connector

2) CAMERA Inputs : BNC input (Camera 1~4) connectors

3) V-out : Composite Out Video Connector

4) A-out : AUDIO Output connector(RCA)

5) VGA : VGA out connector

6) Power Out : Power out for Cameras (12V/1.5A)

7) LAN (RJ-45 Ethernet Port) : For connecting to remote PC via Ethernet network.

8) SENSOR (ALARM IN 1~4) : For connecting alarm inputs.

RELAY (ALARM OUT) : For connecting alarm out relays.

9) POWER : DC power Jack

10) USB : For connecting USB compatible devices

11) RS 422/485 : Tx(+, -) & Rx(+, -)

12) External IR Receiver : Connector for Wired Remote Controller

13) A-in : AUDIO input connector(RCA)

11 MOBILE DIGITAL VIDEO RECORDER

3. Remote Controller

12 MOBILE DIGITAL VIDEO RECORDER

4. Virtual Keypad for Mouse Control.

The DVR can be controlled by Mouse. If mouse is connected to the device via

USB port, virtual remote controllers and keypad shows up automatically to the screen when needed. – Entering Password.

[Virtual Keypad]

[PTZ]

13 MOBILE DIGITAL VIDEO RECORDER

II.INSTALLATION & CONNECTIONS

1. Camera, Monitor, Microphone, Alarm sensor and Power cord

1-1. System Configuration Diagram

The following illustration is showing the fully installed system.

14 MOBILE DIGITAL VIDEO RECORDER

2. PC System Requirements for Network Connection.

(a) Pentium-4 2.0GHz or higher

(b) 256MB System Memory

(c) 1,024 x 768 Display Resolution, 32 Bit color

(d) Windows XP, VISTA, 7

(e) Spare 10/100-BaseT Ethernet Port

(f) Microsoft DirectX 9.0c

It is recommended to have DirectX 9.0c version in Client PC. DirectX 9.0c is available for download from Microsoft homepage

(www.microsoft.com/windows/directx).

<Disclaimer>

The remote viewing on network connection may not work on all personal computers due to difference in personal settings and hardware configurations.

15 MOBILE DIGITAL VIDEO RECORDER

III.QUICK SETUP

To turn on the DVR, Turn one [POWER] switch on the front panel. When the Digital

Video Recorder is powered on, the Live Viewing screen will appear in about 30sec.

1) Press [Menu] Button.

2) Enter the password using Numeric buttons when prompted for a password.

<The Factory Default password for the unit is “000000”>

3) QUICK SETUP menu appears once a password is entered.

4) Use Directional buttons to select menu and use “-/+” buttons to set value of each menu.

16 MOBILE DIGITAL VIDEO RECORDER

1. RECORD

1-1. RECORD MODE

1) Select “RECORD MODE” on TAP menu by using Directional buttons.

2) Select MODE by pressing “–/+” buttons on the remote controller or on the unit.

3) Press [ENTER] button to exit a menu with saving changes. Press [CANCLE] to exit a menu without making changes.

MODE1 ~ MODE 8 : Default

RECORD

MODE

Channel

1

Resolution

D1(720*480)

Continuous

15/Q3

Motion

OFF/Q4

Alarm

30/Q4

2

3

4

CIF(360*240)

CIF(360*240)

CIF(360*240

15/Q3

15/Q3

15/Q3

OFF/Q4

OFF/Q4

OFF/Q4

30/Q4

30/Q4

30/Q4

NOTE: Each(MODE1 to MODE8) recording modes are customizable in Advaced Menu.

2. AUDIO IN

Select the channel of where you want to record the audio from by using “-/+” buttons.

3. POST RECORDING

Set up the post recording duration after a motion or event is triggered using “-/+” buttons.

4. RUN ADVANCED

Select “ON” or “OFF” by pressing “–/+” buttons on the remote controller or on the unit.

1) “ON” : Select this to enter into main menu and press [ENTER] button to exit a menu with saving changes.

 Escape from “QUICK SETUP” menu by pressing “ESC” button.*

 Press MENU button again to enter into MAIN MENU.

2) “OFF” : Select this to stay on “QUICK SETUP” menu.

3) To resume Quick SETUP menu from Main Menu, refer to 2-1 DISPLAY SETUP part in manual

17 MOBILE DIGITAL VIDEO RECORDER

IV. LIVE VIEWING

1. Display Overview

[Date/Time] – Displays current date and time or the date and time of the

recording

[Device Status] – Displays status of the device

: Left Storage Percentage

: USB Connection (Front Panel)

: USB Connection (Back Panel)

: Recording Command

: Schedule Recording Set-up

: LAN Cable Connection

: 3G Connection

[Alarm Indicator] – Displays the detected input alarms

[Alarm Indicator(Vehicle)] – Displays the detected alarms from GPS and

G-Sensor (High Speed, Shock, Sudden Acceleration/Deceleration)

[Channel Status] – Displays channel information

: Video Loss

: Motion Detected

[GPS/G-Sensor Information]

: GPS Coordinates

: G-Sensor Value

: Speed

18 MOBILE DIGITAL VIDEO RECORDER

2. Multi screen Display and Sequencing

2.1 . Full Screen Display

Select any camera for Full screen display by pressing the Number button of the desired camera.

2.2 . Multi-screen Display and Sequencing Display.

Press [DISPLAY] buttons to activate the multi-screen display. It is changed the order as among your choice of SPLIT MODE. While in 4-way screen display, press [DISPLAY] button for 1 second to begin full screen sequencing. The sequence mode and dwell times are programmable. For detailed information about configuring those, see

Sequence Setup”. If the sequence mode is not activated, it moves to Quad mode instead of Sequencing.

3. Zooming

During live view mode or playback, it is possible to zoom into a section of the screen to get a close-up view of the screen.

1. To activate the digital zoom, select the full screen display of the camera you wish to zoom.

2. Then press the [ZOOM] button on IR Remote controller. Zoom area box pops up, as shown below. x 2 x 4

3. Move the box to the desired position using Direction [ ] buttons.

4. Press [+] button to enlarge the image. Press [ - ] button to zoom out the image.

5. Press [CANCEL] button to return normal mode.

<Note>

If the Zoom button is pressed while in a multi-screen display, zoom operation is not activated.

19 MOBILE DIGITAL VIDEO RECORDER

V. OPERATION

1. Main Menu Overview

When the DVR is powered on, Live Viewing screen will appear after initialization about 30sec. Press [MENU] button to access the main menu. An Admin Password Box will appear. Enter the password using Numeric buttons on IR remote controller.

Default password is „000000‟. Main Menu appears after proper password entered, shown as below.

<Note> Factory default Admin/user password is

[000000]. It is recommended to change the “PASSWORD” when you install the DVR. Refer to [System Setup].

.

Use Direction buttons

[ ] to select the desired menu. Items selected in the menu are represented in color.

. Press [ENTER] button to select the menu and display Sub-Menu. Use Left/ Right buttons [ ] to select on TAP menu.

Selected items changed into [ORANGE] color.

Selected Not selected

* It is automatically saved changes when you move between TAP menus.

Press [ENTER] button to exit a menu with saving changes.

Press [CANCEL] to exit a menu without changes.

20 MOBILE DIGITAL VIDEO RECORDER

2. Display Option

2.1. Display Setup

1. Use Direction buttons [ ] to select “DISPLAY” menu. Then, press [ENTER] button to display “DISPLAY SETUP”.

2. Use Left/Right buttons [ ] to select on TAP menu

( ). Selected items changed [ORANGE] color.

3. Use Down [] button to specify.

4. Use [-, +] button to change the values.

ITEM ADJUSTMENT

OSD

Select “Show” or “Hide” to display the OSD SETUP information on main display screen.

CAMERA

BORDER LINE

BACKGROUND

SPLIT MODE

Select On-Screen-Display information for Camera Number.

Select Board Line between cameras.

[BLACK DARK GRAY GRAY WHITE]

Select Background color on NO VIDEO status.

[GRAY WHITE BLUE BLACK DARK GRAY]

Display is changed the order as shown below among your choice of

SPLIT MODE.

QUICK SETUP

Select “On” to resume “Quick SETUP” menu and “Off” to stay on main menu setup.

5. Save changes and exit the menu, press [ENTER] button.

Exit the menu without making changes, press [CANCEL] button.

21 MOBILE DIGITAL VIDEO RECORDER

2.2. Sequential Setup (Auto Sequence)

ITEM

DWELL TIME

SEQ. MODE

FULL SCREEN

2.3. OSD Setup

DEFAULT

5 Sec

None

ALL

ADJUSTMENT

Specify the dwell time of each camera or Multi screen mode is displayed. Use

[-, +] button :

[1 second ~ 30 seconds]

Select desired sequence mode to switching.

Select the cameras to be included or excluded from the automatic sequencing.

ITEM

ITEM

S

SPEED

DEFAULT

All

Checked

KM

ADJUSTMENT

Select desired information items to be displayed on screen.

[System Bar, Sensor Bar, Speeding, Shock, Acceleration,

Deceleration, Alarm]

Select desired speed unit

[MPH, KM/H]

22 MOBILE DIGITAL VIDEO RECORDER

3. Camera Setup

1.

Use Direction buttons [

] to select “CAMERA” menu. Then, press [ENTER] button to display “CAMERA”.

2. Use Left/Right buttons [ configure.

] or Number button to select the Camera you wish to

3. Use Down [] button to move specified menu and use Left/Right buttons

[] to select other item.

4.

Use [-, +] button to change the value.

ITEM

BRIGHTNESS

CONTRAST

COLOR

SENSITIVITY

MOTION GRID

DEFAULT

50%

50%

50%

10

ADJUSTMENT

The brightness of each camera can be adjusted by pressing [-,+] buttons.

The contrast of each camera can be adjusted by pressing [-,+] buttons.

The color of each camera can be adjusted by pressing [-,+] buttons.

Level 1: Low sensitivity~ Level 20: High sensitivity.

Use this menu to setup Zones for the motion detection The screen shown below will overlay the current video image.

Motion zones are set by on – it‟s covered as cross stripes Screen.

It is divided into 16 Grid and selected by Number button on IR Remote.

: Select All. Press Enter to select

: Clear All. Press Enter to select

: Select specific. Press Enter to select.

23 MOBILE DIGITAL VIDEO RECORDER

Motion detected zones will be changed to BLUE Color.

Motion Detected zones

USE Numeric button to select Motion Grid. GRAY Will be cleared. Or Use

<+> button to select Motion Grid at Front Panel. Running Man Icon will be activated. <+> button is used for selecting and cancel. Use <-> button to escape from Grid Menu.

P/T/Z ID/MODEL

None

Camera

No

It is also possible to select smaller motion grids for more precise motion detection by using CMS.

Select P/TZ camera model to control.

Select appropriated channel for the PTZ camera. Camera ID means

Camera address.

24 MOBILE DIGITAL VIDEO RECORDER

5. Save changes and exit the menu, press [ENTER] button.

Exit the menu without making changes, press [CANCEL] button.

No

1

2

3

4

5

6

7

8

1st

Press

A

C

E

G

I

K

M

O

2nd

Press

B

D

F

H

J

L

N

P

3rd

Press

1

2

3

4

5

6

7

8

No

9

0/10

11

12

13

14

15

16

1st

Press

Q

S

U

W

Y

.

-

2nd

Press

R

T

SPACE

V

X

Z

@

_

<Insert characters from IR Remote Controller >

3rd

Press

9

0/10

11

12

13

14

15

16

25 MOBILE DIGITAL VIDEO RECORDER

4. Recording

4.1. General Settings

The DVR comes with a certain preset settings from the factory. Therefore once the DVR is installed, immediate recording is possible after pressing the record buttons. By default, audio alarm, motion recording are off.

. Use Direction buttons [ to display “GENERAL”.

] to select “RECORD” menu. Then, press [ENTER] button

2 . Use Direction buttons [

] to select the Camera you wish to configure.

. Use [-, +] button to change the value.

ITEM

REC MODE

ADJUSTMENT

Select preset recording mode. (MODE 1 to 8 - Customizable)

The recording mode presets are shown in the manual article 1-1.

RESOLUTION

Resolution changes automatically according to [REC MODE]

POST RECORD

Adjust the post recording duration after a motion is detected or event is triggered.

(Preset is 40 sec)

RECORD LIMIT  Set a maximum recording time limit from 12 hours to 30 days.

ON BOOT

Select whether the device starts recording on boot or records on

REC. schedule.

4. Save changes and exit the menu, press [ENTER] button.

5. Press [REC] button. Then, the red REC LED lights on the front panel and recording starts.

6. To Record stop, press the “ STOP” button on IR remote or on Front Panel.

26 MOBILE DIGITAL VIDEO RECORDER

4.2. Advanced Set Up

RATE

ITEM ADJUSTMENT

Select recording speed for each camera.

: Recording resolutions is changed to Frame, Field and CIF mode.

<Refer to System >

QUALITY

MOTION

Specify the record picture quality for each camera.

ULTRA  SUPER  HIGH  MIDDLE LOW

Select Motion Recording ON or OFF. Camera does not record under normal conditions. It is discussed on EVENT Section.

ALARM

Select Alarm Recording ON or OFF. Camera does not record under normal conditions. It is discussed on EVENT Section.

<Note> Press [MENU] button on each Item at first line to apply all setting for the rest channel. Each(MODE1 to MODE8) recording modes are customizable in Advaced Menu.

Please see Page 17.

< Approximate File Size>

Quality NTSC PAL

LOW

MIDDLE

HIGH

SUPER

720x480 720x240 360x240 720x576

5.1 3.2 2.0 6.1

7.2

10.2

15.4

24.6

4.5

6.4

9.6

15.4

2.8

4

6

9.6

8.6

12.3

18.4

29.5

720x288 360x288

3.8 2.4

5.4

7.7

11.5

18.4

3.4

4.8

7.2

11.5

UNIT

KB

KB

KB

KB

KB ULTRA

* It is calculated by theoretical, therefore it may be different depends on Video

Signals or other conditions in actual.

27 MOBILE DIGITAL VIDEO RECORDER

4.3. Chart (Schedule Recording)

The schedule chart shows a graphical representation of the defined record mode: Mode1~8. Default setting values are all same in 8 different modes at first. But user can set 8 different schedules as he wants. Please be noted that, the schedules are only displayed if a corresponding schedule has been configured in the chart menu.

It breaks down the days of the week in eight different categories: ALL, SUN, MON,

TUE, WED, THU, FRI and SAT. ALL is for everyday of the week. Daily schedule has priority to ALL.

. Press [Enter] button you wish to configure. The detailed menu pops up for selected Day, as shown below.

. Enter the beginning and end time, then select Record mode to record.

(1) BEGIN: The time of recording start.

(2) END: The time of recording end. The ending time must not be before the starting time or the same as the starting time. It must be any time over the starting time.

. MODE: Up to 8 different recording modes can be pre-determined for schedule recording. (MODE1 ~ MODE8)

28 MOBILE DIGITAL VIDEO RECORDER

<Note>

The recording time is set by 24H(00:00 - 23:59). You need to set 2 days if the setting is over one day.

D/W

Monday

BEGIN

18:00

END

23:59

MODE

MODE 1

Tuesday 00:00 08:59 MODE 1

 The recording would not start when Ending time is ahead of Start time.

EX)

D/W BEGIN END MODE

Monday 18:00 08:59 MODE 1

. To activate the schedule recording after setting, press the SCHEDULE button.

The SCHEDULE indicator illuminates. When a program covers the current time, the REC indicator illuminates and the unit begins recording. Please note that if there are no schedules configured, then the DVR will not record.

. When the scheduled recording time is over, the REC indicator goes off and recording stops.

. If you wish to stop recording while scheduled recording, press the SCHDULE button, then the SCHEDULE indicator goes off and the Schedule Recording

Mode is released.

*Alternative Method

. Place the cursor on the desired starting time of schedule recording using the arrow keys and press [+].

. Place the cursor on the desired end time of the schedule recording using the arrow keys and press [+].

. Select the recording mode.

. The activated schedule recording will be shown as above in colors depending on the mode you selected.

29 MOBILE DIGITAL VIDEO RECORDER

5. Device

The menus are displayed with options on the left-hand column and settings in the right hand column. A cursor (highlighted menu) can be moved using the Direction buttons [ ] .

5.1. GENERAL

ITEM ADJUSTMENT

KEYPAD MODEL

Select Joystick Controller and Baud Rate.

POS MODEL

Select POS Device to connect with the DVR

AUDIO IN

KEY TONE

Select audio recording device.

The audio data is always recorded in real time unlike the video data that can be recorded in various modes including real time.

There may be a slight delay in synchronization of the audio to video

By default, the DVR emits a beep every time a button is pressed. Set the key tone to off to turn button beep off. Default by “ON”

30 MOBILE DIGITAL VIDEO RECORDER

5.2. ALARM

ITEM

RECORD

CAMERA

ALARM BUZZER

ALARM OUT

INPUT

ADJUSTMENT

ALL: Start to record All Alarm “ON” channel if there is any

Alarm signal is triggered.

ON: The buzzer Sounds if an alarm is triggered. The buzzer will sound for the duration of the RECORD TIME. This buzzer related with Alarm Out. Please configure Alarm Out “ON” for Alarm buzzer.

OFF: Disables the ALARM BUZZER function.

Configure which relay will be triggered when an alarm is activated per camera. Select from four available options:

Video Loss, Motion, Alarm ALL, Each Alarm, System.

<Note> If “System” is selected, the relay will be triggered when

System has problems such as HDD FAIL, Power loss etc.

Press [Cancel] button to stop Alarm Out.

It will be cleared by an order: Alarm>Motion> Video Loss

Select alarm channel you want to configure by using (-,+) buttons.(1~4)

Select the input type or turn of the alarm of each channel.

Select the name of the alarm or leave it unknown when accurate name is not found in the selection.

[Unknown, Front Door, Rear Door, Turn Left, Turn Right, Breaking,

Emergency light, Lengthy stop, Emergency]

User can choose name of the sensors among them.

[N.O., N.C.] : Default sensor setting

* N.O(Normal Opened) : ex) Opened door is default for the alarm.

* N.C(Normal Closed) : ex) Closed door is default for the alarm.

Set up the input reference duration of the alarm.

31 MOBILE DIGITAL VIDEO RECORDER

When duration of the input signal exceeds the set value, the device recognizes and displays it as each alarm.

2. Save changes and exit the menu, press Enter button.

Exit the menu without making changes, press [CANCEL] button.

5.3. SHOCK SENSOR

ITEM ADJUSTMENT

SHOCK SENSOR

Select to turn on/off the Shock Sensor

Select the threshold value of the shock sensor of each axis.

X/Y/Z

THRESHOLD

The impact over the set threshold value will be recognized and displayed as “shock” alarm. (0.1 ~ 4.0g)

Select the standard value of the shock sensor of each axis.

X/Y/Z

STANDARD

The current sensor value on the right indicates the position value of the device depending on the installed position of the device.(-1.0~1.0g)

The setting sensor value is best to compensate the current value summing the two values to 0.

32 MOBILE DIGITAL VIDEO RECORDER

5.4. SPEED

ITEM

SPEED USE

SPEED LIMIT

ACCELERATION

/

DECELERATION

ADJUSTMENT

Select to turn on/off the use of speed recording and alarm.

Set the speed limit for speeding alarm.

When the vehicle exceeds the set speed limit, the device will recognize and display the status as “speeding”.

Set the “KM/H per Second” value for Acceleration

/Deceleration alarm.

When the vehicle‟s speed change per second exceeds the set value, the device will recognize and display the status as

“Acceleration(When speed increases) or Deceleration(When speed decreases)”.

33 MOBILE DIGITAL VIDEO RECORDER

6. Network Setup

The static service consists of an IP address that remains constant for the duration of the contract of the internet service, whereas the dynamic service consists of an IP address that frequently changes every time a new connection is made through the provided modem, or recurrently in a given period of time. Though most internet service providers offer both solutions, this manual will distinguish the two solutions according to the commonly available service type to configure the DVR for the networking purposes.

6.1. IP setup

.

Us e Direction buttons [ ] to select “NETWORK” menu.

Then, press [ENTER] button to display “Network”.

. Use Down button [ ] to specify the detail.

. Use [-, +] button to change the value.

. Save changes and exit the menu, press [ENTER] button.

Exit the menu without making changes, press [CANCEL] button

ITEM

CONFIG

IP Address

Netmask

Gateway

ADJUSTMENT

STATIC IP: Edit IP address, Gateway and Netmask.

DHCP: Dynamic Host Configuration Protocol.

It is automatically set on from Local DHCP if there is Local DHCP server (i.e. The local Router) . if the DHCP is set to ON, the IP address, Gateway and subnet

Mask will be assigned by DHCP server.(i.e.The local area network Router)

Enter the static IP address

Enter the IP address of subnet mask.

Enter the IP address for the internet gateway server.

34 MOBILE DIGITAL VIDEO RECORDER

DNS Server

PORT

Verify the name of the domain name system

Select “0000 ~ 9999”

Enter the port number that the client will use to communicate with the DVR over the internet. The default port is 7000. It is recommended to use over

1,000.

6.2. Wireless

The “Wireless” function of the device is for use of the 3G networking. Wifi function(Hot spot) also will be supported in near future.

The device automatically connects the device to the network by default once the network is properly set-up.

The menus are displayed with options on the left-hand column and settings in the right hand column. A cursor (highlighted menu) can be moved using the Direction buttons [

ITEM

] .

ADJUSTMENT

VENDOR

NONE : Not in use

Select the Provider of connected USB-type Modem

(e.g. China-M, Chunghwa, SKT, Taiwan-M, Verizon, Globe, H3G)

IP Address

Server IP

Server Port

Status

Displays your IP address

Enter the server IP

Enter the server Port

Click the button to confirm the connection. A success message will appear.

35 MOBILE DIGITAL VIDEO RECORDER

7. System Setup

7.1. General

. Use Direction buttons [] to select “SYSTEM” menu. Then, press [ENTER] button.

. Use Left/Right buttons [] to select on TAP menu

. Use Down button [] to specify the detail.

.

Use [-, +] button to change the value.

.

Save changes and exit the menu, press [ENTER] button.

Exit the menu without making changes, press [CANCEL] button.

ITEM

SYSTEM ID

AUTO LOG OUT

PB DEINTERLACE

PASSWORD

FACTORY

DEFAULT

ADJUSTMENT

To select the DVR to be controlled with the remote controller, press and hold the DVR ID button. While holding the DVR ID button, press the appropriate DVR ID number. For example, enter 05 for DVR ID 05, enter

43 for DVR ID 43, and such.

Set the ID of IR controller on “00” to control DVRs at the same time, whatever DVR IDs are.

The DVR locks all the buttons after three minutes of inactivity like a

Screensaver. The buttons can be unlocked with the user password.

Default by “OFF”.

ON: Reducing image flickering but less picture quality.

OFF: Better picture quality for still image but having flicker for moving picture.

If you choose “OFF”, The password window will not be shown except POWER/

SERVICE MENU/ RECORDING STOP/ SCHEDULE RECORDING STOP.

To restore factory default settings, stop recording and then execute “START” by using ENTER button.

36 MOBILE DIGITAL VIDEO RECORDER

7.2. Time

ITEM

TIME ZONE

ADJUSTMENT

Select the time zone of the region of use.

DATE

TIME

Enter the Date

Enter the Time

If the DVR is connected with GPS, the time of the device can be synced with the time information received by the GPS

ON(Default) : Set the clock of the DVR according to the time information GPS Sync received by the GPS.

OFF : Set the time manually and do not sync with GPS.

<note> Please STOP the recording before Time Setting.

37 MOBILE DIGITAL VIDEO RECORDER

7.3. Account

Admin can define each user‟s Authority. Select User 1~5 , then select

Activate option on or off. When enabled, it will be possible to check individually under user settings: Monitoring, Playback, Back up, Network,

Configuration (Main Menu Setup), Shutdown (Power off), Record stop.

Enter the 6 numbers for the new password, and then re-enter the same password under COMFIRM section. The asterisks will advance automatically as the numbers are entered.

38 MOBILE DIGITAL VIDEO RECORDER

7.4. DISK

ITEM

FORMAT

OVERWRITE

DISK MONITOR

ADJUSTMENT

1. Stop the DVR completely before the disk format.

2. Use [-, +] button to change select device.

* Internal HDD

* USB – Memory Stick

* USB – CD/DVD-RW

* USB – HDD

<Note>

When you format USB-HDD, it is formatted to FAT 32 format type.

3. Use down button [] to move

button to start formatting.

, then press [“+” or “ –“]

4. Formatting will begin, and the progress will be displayed at the bottom of the window. Please not that it takes 10~30 seconds for format a HDD.

5. When formatting is finished, it will display COMPLETE, and also SUCCESS at the bottom of the window.

Users may select the record policy of the system‟s internal hard disk drive.

By default, the system‟s hard disk drive is set to overwrite from the beginning when it becomes full.

ON: By default, the hard disk drive will overwrite from the beginning when it becomes full.

OFF: It stops recording after HDD is full.

It stops automatically if HDD failure happens. It starts to “Monitoring” again after DVR reboot . (Use [-, +] button to stop or start)

39 MOBILE DIGITAL VIDEO RECORDER

7.5. UPDATE.

1) Download the latest firmware file and copy to USB Flash memory stick in the Root Folder.

2) Turn on your DVR (If you are using, please stop the recording)

Indicator

H/W VERSION

S/W VERSION

CONDITION

Shows the Main PCB version of the system.

Shows the Software version of the system.

3) Plug USB memory stick into the front or rear USB port and check if USB icon shows up on the Status bar.

4) Move to upgrade menu and start upgrade by pressing [+]/[enter] button.

5) Wait until upgrade finished and show “Success” message, then Press [+] to restart.

<NOTE>

1. Please make sure your USB Flash memory stick has enough space for update file size.

2. Do not make special folder into memory stick for these files.

3. Do not format the USB at window, just remove all files inside.

4. Do not switch OFF or PRESS any key during the upgrade process.

5. Please consult with your installer or seller before upgrade DVR.

40 MOBILE DIGITAL VIDEO RECORDER

7.6. INFO

Press info button on IR remote to display the information. The other menu is blocked to move. This menu provides information such as listed below.

Indicator CONDITION

LANGUAGE

Display Current Language and you can change language here.

User cannot change Language while it‟s under recording mode.

MODEL

HOSTNAME.

NETWORK

STORAGE

USB (FRONT)

USB (REAR)

VOLTAGE

TEMPERATURE

Display Channel Number and compression.

Display hostname and Mac Address.

Shows the current IP and Port of this unit.

Displays numbers of SD CARDS and storage size

Displays what kind of device is connected to the front USB connector.

Displays what kind of device is connected to the rear USB connector.

Shows the input voltage value

Shows the device temperature

41 MOBILE DIGITAL VIDEO RECORDER

7.7. MOBILE

Fill the information under the “Mobile” in order to identify the device and the vehicle which the device is installed in. The identification information will be sent to the “Central Monitoring Software” when used with 3G network connection.

42 MOBILE DIGITAL VIDEO RECORDER

VI.PAN/TILT/ZOOM CONTROL

1. P.T.Z. Menu

1.

To activate the Pan/Tilt Control, select the full screen display of the camera

2. you wish to control.

Then press the [

P/T/Z/FOCUS

] button. Shortcut Menu box pops up, as shown

below.

INDICATOR

<Note > Please Refer to Help Menu for specific control.

RESULTING ACTIONS

Press this button to display “HELP” Menu. Press [ENTER] Button again, or

[CANCEL] button to cancel Help Menu.

[ENTER]

Press this button to cancel “PAN/TITL” Operation.

[CANCEL]

[MENU]

PTZ camera control interface will be extended to use whole function.

Press this button again to make short-cut menu.

To Tilt up and Down.

To pan Right and Left.

Zooming In and Out.

The layout of the PTZ interface conforms to the layout of the front of the DVR or the remote controller. Menu button is the guide anchor position for all other buttons.

When in PTZ interface mode, all buttons used for the PTZ related operation.

43 MOBILE DIGITAL VIDEO RECORDER

** Please Check below items before using PTZ Camera.

1. RS 422/485 Connection, camera Jumper Setting and etc

2. Set the PTZ Camera ID & MODEL NO at the Display menu

2. Preset & Tour

Button Function

Set preset position; SPOT OUT on remote controller a. Move the PTZ into desired location. b. Press the Preset button. c. Custom 1 will illuminate. d. Set the # for the Preset location. e. Press Enter to save and exit.

Go to preset position; INFO on remote controller a. Press Go to button. b. Enter the desired Preset # and press Enter.

Start Auto Tour; BACKUP on remote controller a. Press Auto Tour Button. b. Press the + button and enter the range of Preset and press Enter. c. For Example, Auto Tour Button, +5 will start the tour of 1 ~ 5 presets of the PTZ Camera

3. Custom Functions

Button Function

PTZ custom function 1; DISPLAY on remote controller

PTZ custom function 2; ZOOM on remote controller

PTZ custom function 3; P/T/Z on remote controller

Please refer to the PTZ manufacture‟s instruction manual for proper jumper settings to match the protocols to the DVR.

44 MOBILE DIGITAL VIDEO RECORDER

4. PTZ Camera Model - PAN/TILT/ZOOM Camera List

A.

# Model Name 3X Speed Preset Go to Tour Pan A.Tilt o o o o o

25

26

27

28

29

30

31

32

1

2

NUVICO, NV 9600 BPS

MERIT LILIN, PIH-

7000/7600

3

4

5

VCL, Orbiter

Microsphere

SAMSUNG, SCC-641

8

9

6

7

NEC, NC-21D

SUNKWANG, SK2107

RESERVED

10

11

D-MAX, PTZ PROTOCOL

LG, LPT-A100L P/T/Z

HONEYWELL, GCC-

655N

WONWOO, PT-101

12~14 PELCO, D 2400~9600

15 C&B TECH, AN200

16 CANON, VC-C4

17~19 PELCO, P 2400~9600

20~22 PELCO, EP 2400~9600

23

24

PANASONIC,

WV-CS/W85x,86x

HONEYWELL, HSDN-

251N/P

GE/KALATEL,

CyberDome

DY ELEC, SmartDome

BOSCH, TC8560/TC700

SYSMANIA, ORX1000

AD, DELTADOME

HUNT, HTZ-2300

HAZEM, RESERVED

RVT, EZ Protocol o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o

Pat Me o o o o o o o o o o o o

Esc/

Enter o o o o o

45 MOBILE DIGITAL VIDEO RECORDER

34

35

36

37

38

39

33 LG, MULTIX

ELMO,

PTC-200C/400C

NICECAM, MP-1xxx

C&B TECH, CNB-PTZ102

IKEGAMI, PCS I-LAN

IKEGAMI, lCD I-LAN

Reserved

TOA, SC80 SYSTEM

CONTROLLER

TOSHIBA, SC1000

40

41 o o

42 BBV, TC 9600 BPS o

<Note> Speed has 0~8 steps o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o

1 (Slow) – 8 (Fast)

* 0 – Keep Pressing the button to increase speed

46 MOBILE DIGITAL VIDEO RECORDER

VII.SEARCH/PLAYBACK

1. Time Search

1. To start playback, press

T

[Time Search] button, Time search Calendar

Menu pops up, as shown below.

2. Use Left /Right button to change the Month on window.

<Note> It will not be changed if there are no stored data on previous/next month.

<Note> The data is color-coded by category: Alarm(Red) > Motion(Green) > Normal (Yellow)

3. Use Up/Down buttons [

] to select “DAY” on Calendar. Selected data will be shown as a graphical representation of the recorded video stored on the DVR.

4.

Select “Hour and Minutes“ or ”the camera” you wish to playback. Then press

[ENTER] button.

<Note>

Time : Multi screen Display

Camera : Full screen Display

5. Press [ENTER] button to start playback.

47 MOBILE DIGITAL VIDEO RECORDER

2. Log List Search/Alarm, Motion Search

The logs can be used to search and review directly to a point in time of the recorded data. Alarm, motion, video loss and system related logs can be searched and played back directly from the time of the incident.

.

To start Event Search, press [Log] button on the front, then Log List

Menu pops up, as shown below.

MENU TAP

ALL

SYSTEM

NETWORK

MOTION

VLOSS

CONDITION

It has a list of all the events since the initial power on procedure of DVR

It shows All Event except for Alarm, Motion, and Video Loss.

It shows NETWORK List.

It shows Motion List.

It shows Video Loss List.

EVENT

It shows EVENT List.

2. Use Up/Down buttons [] to desired “Time” to playback. Use Left/Right buttons [] to move NEXT page.

3. Press [ENTER] button to start playback.

<Note> Log list is saved on HDD.

<Note> To save log output, please connect USB memory stick into USB port on front. Then press Display button on each category to backup Log data. USB Icon will be flashed as

Blue.

48 MOBILE DIGITAL VIDEO RECORDER

VIII.BACKUP

1. USB Memory Stick / External USB HDD Backup

USB Memory stick or External USB-HDD is recognized within 10 seconds after plug in

USB Connection cable to UBS port in DVR.

<Note>

 You must stop all recording before performing backup to Memory stick or external USB HDD.

ONLY FAT 32 Format disk will be read through Window PC.

The data in FAT 32 format disk is not replayed on DVR. Format is discussed in “SYSTEM>DISK”

Section.

1. Plug in USB connector into the USB connection port on the front panel.

2. Press [BACKUP] button to display the backup menu.

3. Use [-, +] button to change select device: USB MEMORY STICK or USB – HDD

4. Please select the data for BACKUP.

5.

6.

Enter the numbers as required in 24-hour format, then move to

Press [ENTER] button to start BACKUP.

.

* USB icon appears when connected to device.

• If there is not enough space on your USB memory stick, the system will not proceed with backup.

USB Memory Stick

 The backup progress indicator will be displayed at the bottom of the window. While the system is in backup session, please do not perform

7. playback.

Finish backup process.

49 MOBILE DIGITAL VIDEO RECORDER

2. Back up Range Setup

It is possible to set up backup range automatically on Time Search Menu[by Month,

Date, Hour, Minute]

Press [-] button to set backup Start time , press [+] button to set End. Selected time will be changed [Light Grey] Color.

Selected backup time from 07:30~07:45 will be displayed on Backup range.

50 MOBILE DIGITAL VIDEO RECORDER

IX. C4K Viewer

1. Installation

(1) Select the install program icon and double-click.

(2) If you agree to the License Agreement, select [agree] and click [next].

51 MOBILE DIGITAL VIDEO RECORDER

(3) Select the folder on your computer that you want to install the software and click [Next].

(4) Select or rename the Start Menu Folder and click [Next].

52 MOBILE DIGITAL VIDEO RECORDER

(5) Select the product [C4K] and click [Install].

(6) Click [Next] when installation is completed. The installation may take a few minutes.

(7) Click [Finish] to complete the installation Process

53 MOBILE DIGITAL VIDEO RECORDER

2. Software

(1)

Main Window a. Alarm Indicator

Alarm Indicator shows the alarm status of the recording. There are 4 preset alarms and 4 customized alarms. The alarms are shown by blinking.

Motion: When device has detected a motion is to be concerned.

Impact : When G-sensor has detected an impact that is to be concerned.

Overspeed : When speed of the vehicle exceeds the speed limit set by user.

Accel/Decel : When acceleration/deceleration exceeds the limit set by user.

It indicates hard acceleration or hard braking.

54 MOBILE DIGITAL VIDEO RECORDER

b. Playback Bar

The playback bar shows the time of each recording file and the G-sensor value at the time of recording. User can check and uncheck the checkbox (X,

Y, Z) value shown on playback bar. c. Speed & Direction Indicator

The Speed & Direction Indicator shows the GPS coordinates, direction and speed at the time of the recording. User can select the speed to be shown in

Km/H or MPH by clicking on the speed unit. The speed unit is shown in bright yellow when activated. d. Video Display

Display shows video recordings, date and time of the recording. User can choose to view each channel or split view by clicking the channel number on the top left. User can show/hide search window by clicking .

55 MOBILE DIGITAL VIDEO RECORDER

e. Playback Control Bar

Play : Plays the video

Back/Forward : Moves the video back/forward 1 second

Pause : Pauses the video

Stop : Stops and closes the recorded file

Previous/Next : Skips to previous/next recorded file

Skip : Moves 1 frame forward

Volume Control / Mute f. File Control Bar

Open : Opens file browser

Snapshot : Save or print the current screen(Video and Map)

: Save current or selected channel image. User can select the place.

: Print out current image

56 MOBILE DIGITAL VIDEO RECORDER

Video Export : Opens Video Export Window

Add the desired time and channel to export to media file and save. User is able to choose to open the containing folder or file after converting is completed.

Exporting might take several minutes depending on the length of video and performance of the PC.

Setup : Opens Setting window

Vehicle info Setup: Vehicle Input the names of customized alarm input.

ETC Setup: User can change the language of the software.

57 MOBILE DIGITAL VIDEO RECORDER

g. Map View

The Map shows the location of the vehicle at the time of recording. Map is powered by Google., Ltd.

(2) Open and Search Files

Open the finder by clicking on icon and select the USB storage drive.

By Selecting the folder, the search window will appear. You can either search through the data using the timetable or list of data.

Select the data you are willing to check and double click on the time or file.

58 MOBILE DIGITAL VIDEO RECORDER

- Event Filter

 Event list would be filtered as the event icon is activated. Activated Icon would be lightened.

How to use? Click „Only event file‟ check box. See the picture below.

<All List> <OverSpeed Event List>

59 MOBILE DIGITAL VIDEO RECORDER

Video Compression

Video Input / Output

Audio input / Output

Frame Rate

Pre-event Recording

Post-event Recording

Sensor Input / Output

FRONT KEY

LED Indicators

HDD

USB

IR Sensor

G-Force Sensor

GPS

Nerwork/Wireless LAN

Power Input

Power Output

Dimension

X.SPECIFICATION

PMR-C4K SPECIFICATION(Mobile DVR)

Part

Specification

4CH

H.264

4 Inputs / 1 Output

1Input/ 1 Output

240@CIF

3 seconds

300 seconds

4 inputs / 1 Output

10 Key

PWR, REC, HDD, NET

Upto 2TB

USB2.0 2EA

Front & Extension cable

3-axis(±8g)

U-Blox (Built-in) + External Antenna

10/100 BaseT

DC12V ~ 24V

12V/1.5A

160mm X 45mm X 170mm(W X H X D)

ETC

BNC/RCA

RCA

Terminal Block

3ф LED

Front/Phone Jack

RJ45

PWR CON

Terminal Block

60 MOBILE DIGITAL VIDEO RECORDER

WEEE Symbol Information

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking shown on the product or its literature, indicates, that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

61 MOBILE DIGITAL VIDEO RECORDER

<Memo>

62 MOBILE DIGITAL VIDEO RECORDER

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals