Volvo V40, 2015 Late Owner's manual

Volvo V40, 2015 Late Owner's manual
WEB EDITION
OWNER'S MANUAL
DEAR VOLVO OWNER
THANK YOU FOR CHOOSING VOLVO
We hope you will enjoy many years of driving
pleasure in your Volvo. The car has been
designed for the safety and comfort of you and
your passengers. Volvo is one of the safest cars in
the world. Your Volvo has also been designed to
satisfy all current safety and environmental
requirements.
In order to increase your enjoyment of the car, we
recommend that you familiarise yourself with the
equipment, instructions and maintenance information contained in this owner's manual.
Table of contents
01 Introduction
Owner information....................................
Reading the owner's manual....................
Digital owner's manual in the car..............
Recording data.........................................
Accessories and extra equipment............
Information on the Internet.......................
Volvo ID.....................................................
Volvo Cars' environmental philosophy.....
The owner's manual and the environment..........................................................
Laminated glass........................................
02 Safety
13
13
16
18
19
19
20
21
General information on seatbelts..............
Seatbelt - putting on.................................
Seatbelt - loosening..................................
Seatbelt - pregnancy................................
Seatbelt reminder......................................
Seatbelt tensioner.....................................
Safety - warning symbol...........................
Airbag system...........................................
Airbags on driver's side............................
Passenger airbag......................................
Passenger airbag - activating/deactivating*............................................................
Side airbag (SIPS).....................................
Side airbag (SIPS) - child seat/booster
cushion.....................................................
Inflatable Curtain (IC)................................
General information on WHIPS (whiplash
protection).................................................
WHIPS - child seats..................................
WHIPS - seating position..........................
When the systems deploy.........................
General information on safety mode.........
Safety mode - attempting to start the
car.............................................................
Safety mode - moving the car..................
25
26
27
27
28
28
29
30
31
31
Pedestrian airbag......................................
Pedestrian airbag - moving the car...........
Pedestrian airbag - folding up..................
General information on child safety..........
Child seats................................................
Child seats - location................................
Child seat - ISOFIX...................................
ISOFIX - size classes................................
ISOFIX - types of child seat......................
Child seats - upper mounting points........
01 02 02
2
23
23
* Option/accessory, for more information, see Introduction.
33
35
36
36
37
38
38
39
40
41
42
42
43
43
44
45
49
50
50
51
53
Table of contents
03 Instruments and controls
Instruments and controls, left-hand drive
car - overview...........................................
Instruments and controls, right-hand
drive car - overview...................................
Combined instrument panel......................
Analogue combined instrument panel overview....................................................
Digital combined instrument panel overview....................................................
Eco guide & Power guide*........................
Combined instrument panel - meaning of
indicator symbols......................................
Combined instrument cluster - meaning
of warning symbols...................................
Outside temperature gauge......................
Trip meter..................................................
Clock.........................................................
Licenses - combined instrument panel.....
Symbols in the display..............................
Volvo Sensus............................................
Key positions............................................
Key positions - functions at different levels..............................................................
Seats, front................................................
Seats, front - electrically operated............
55
58
61
Seats, rear................................................. 80
Steering wheel.......................................... 82
Light switches........................................... 83
Position/parking lamps............................. 85
Daytime running lights.............................. 85
Tunnel detection*...................................... 86
Main/dipped beam.................................... 86
Active high beam*..................................... 87
Active Xenon headlamps*......................... 89
Rear fog lamp........................................... 89
Brake lights............................................... 90
Hazard warning flashers........................... 90
Direction indicators................................... 91
Interior lighting.......................................... 92
Home safe light duration........................... 93
Approach light duration............................ 93
Headlamps - adjusting headlamp pattern............................................................ 94
Wipers and washing.................................. 97
Power windows......................................... 99
Door mirrors............................................ 101
Windows and rearview and door mirrors
- heating.................................................. 102
Rearview mirror - interior........................ 103
Glass roof*..............................................
Compass.................................................
Menu navigation - combined instrument
panel.......................................................
Menu overview - analogue combined
instrument panel.....................................
Menu overview - digital combined instrument panel..............................................
Messages................................................
Messages - handling...............................
MY CAR..................................................
Trip computer.........................................
Trip computer - analogue combined
instrument panel.....................................
Trip computer - digital combined instrument panel..............................................
Trip computer - supplementary information..........................................................
Trip computer - trip statistics*................
03 03 03
61
62
65
66
68
70
70
70
71
72
74
75
76
77
79
103
104
105
106
106
106
107
108
109
110
114
118
119
* Option/accessory, for more information, see Introduction.
3
Table of contents
04 Climate control
General information on climate control... 121
Actual temperature................................. 122
Sensors - climate control........................ 122
Air cleaning............................................. 122
Air cleaning - passenger compartment filter............................................................ 123
Air cleaning - Clean Zone Interior Package (CZIP)*.............................................. 123
Air cleaning - IAQS*................................ 124
Air cleaning - material............................. 124
Menu settings - climate control.............. 124
Air distribution in the passenger compartment.................................................. 125
Electronic climate control - ECC*........... 127
Electronic temperature control - ETC..... 128
Heated front seats*................................. 129
Heated rear seat*.................................... 129
Fan.......................................................... 130
Auto-regulation....................................... 130
Temperature control in the passenger
compartment.......................................... 131
Air conditioning....................................... 131
Demisting and defrosting the windscreen..................................................... 132
Air distribution - recirculation.................. 133
05 Loading and storage
Air distribution - table............................. 134
Engine block heater and passenger compartment heater*..................................... 136
Engine block heater and passenger compartment heater* - direct start................ 137
Engine block heater and passenger compartment heater* - immediate stop......... 138
Engine block heater and passenger compartment heater* - timer.......................... 138
Engine block heater and passenger compartment heater* - messages................. 139
Additional heater*.................................... 140
Fuel-driven additional heater*................. 140
Electric additional heater*....................... 141
Storage spaces.......................................
Storage compartment driver’s side........
Tunnel console........................................
Tunnel console - armrest........................
Tunnel console - cigarette lighter and
ashtray*...................................................
Glovebox.................................................
Glovebox - cooling..................................
Inlay mats*..............................................
Vanity mirror............................................
Tunnel console - 12 V-sockets...............
Loading...................................................
Loading - long load.................................
Roof load.................................................
Load retaining eyelets.............................
Loading - bag holder .............................
Loading - folding bag holder*.................
12 V socket - cargo area.........................
Cargo net................................................
Hat shelf..................................................
04 04 05
4
* Option/accessory, for more information, see Introduction.
143
145
145
145
146
146
146
147
147
147
148
149
149
150
150
150
151
152
154
Table of contents
06 Locks and alarm
Remote control key.................................
Remote control key - losing ...................
Remote control key - personalisation*....
Locking/unlocking - indicator.................
Lock indicator.........................................
Remote control key - electronic immobiliser..........................................................
Remote-controlled immobiliser with
tracking system.......................................
Remote control key - functions...............
Remote control key - range....................
Remote control key with PCC* - unique
functions.................................................
Remote control key with PCC* - range...
Detachable key blade.............................
Detachable key blade - detaching/
attaching.................................................
Detachable key blade - unlocking doors
Remote control key/PCC - replacing the
battery.....................................................
Keyless drive*..........................................
Keyless Drive* - range.............................
Keyless Drive* - secure handling of the
remote control key..................................
156
156
157
158
158
Keyless Drive* - interference to remote
control key function................................
Keyless Drive* - locking..........................
Keyless Drive* - unlocking......................
Keyless Drive* - unlocking with the key
blade.......................................................
Keyless Drive* - lock settings.................
Keyless Drive* - antenna location...........
Locking/unlocking - from the outside ....
Manual locking of the door.....................
Locking/unlocking - from the inside.......
Total airing function................................
Locking/unlocking - glovebox.................
Locking/unlocking - tailgate....................
Locking/unlocking - fuel filler flap...........
Deadlocks*..............................................
Child safety locks - manual activation....
Child safety locks - electrical activation*
Alarm.......................................................
Alarm indicator........................................
Alarm - automatic re-arming...................
Alarm - automatic arming.......................
Alarm - remote control key not working.
Alarm signals...........................................
167
168
168
Reduced alarm level............................... 180
Type approval - remote control key system.......................................................... 181
06 06 06
159
159
160
161
162
163
163
164
164
165
166
166
167
169
169
170
170
171
172
173
173
173
175
175
176
177
178
179
179
179
180
180
* Option/accessory, for more information, see Introduction.
5
Table of contents
07 Driver support
Electronic stability control (ESC) - general..........................................................
Electronic stability control (ESC) - operation..........................................................
Electronic stability control (ESC) - symbols and messages.................................
Road Sign Information (RSI)...................
Road sign information (RSI)* - operation
Road sign information (RSI)* - limitations
Speed limiter*..........................................
Speed limiter* - getting started...............
Speed limiter* - changing speed.............
Speed limiter - temporary deactivation
and standby mode*.................................
Speed limiter* - alarm for speed exceeded..........................................................
Speed limiter* - deactivation...................
Cruise control*........................................
Cruise control* - managing speed..........
Cruise control* temporary deactivation
and standby mode..................................
Cruise control* - resume set speed........
Cruise control* - deactivate....................
Adaptive cruise control (ACC)*...............
Adaptive cruise control* - function.........
183
184
Adaptive cruise control* - overview........
Adaptive cruise control* - managing
speed......................................................
Adaptive cruise control* - set time interval............................................................
Adaptive cruise control* - temporary
deactivation, and standby mode............
Adaptive cruise control* - overtaking
another vehicle........................................
Adaptive cruise control* - deactivate......
Adaptive Cruise Control* - queue assistance.......................................................
Adaptive cruise control* - switch cruise
control functionality................................
Radar sensor...........................................
Radar sensor - limitations.......................
Adaptive cruise control* - fault tracing
and action...............................................
Adaptive cruise control* - symbols and
messages................................................
Distance Warning*..................................
Distance Alert* - limitations.....................
Distance Alert* - symbols and messages
City Safety™...........................................
City Safety™ - function...........................
City Safety™ - operation........................
201
202
203
City Safety™ - limitations....................... 218
City Safety™ - laser sensor.................... 220
City Safety™ - symbols and messages.. 222
Collision warning system*....................... 223
Collision warning system* - function...... 224
Collision warning system* - detection of
cyclists.................................................... 225
Collision warning system* - detection of
pedestrians............................................. 226
Collision warning system* - operation.... 227
Collision warning system* - limitations... 229
Collision warning system* - camera sensor limitations.......................................... 230
Collision warning system* - symbols and
messages................................................ 231
Driver Alert System*................................ 232
Driver Alert Control (DAC)*...................... 232
Driver Alert Control (DAC)* - operation... 233
Driver Alert Control (DAC)* - symbols and
messages................................................ 234
Lane Keeping Aid*.................................. 236
Lane Keeping Aid - function................... 236
Lane Keeping Aid - operation................. 238
Lane Keeping Aid - limitations................ 238
07 07 07
6
185
187
187
189
189
190
191
191
192
193
193
194
195
196
197
198
199
* Option/accessory, for more information, see Introduction.
203
204
205
205
207
208
208
210
211
213
214
215
216
216
217
Table of contents
08 Starting and driving
Lane Keeping Aid - symbols and messages.......................................................
Park assist syst*......................................
Park assist syst* - function.....................
Park assist syst* - backward..................
Park assist syst* - forward......................
Park assist syst* - fault indication...........
Park assist syst* - cleaning the sensors.
Park assist camera..................................
Park assist camera - settings.................
Park assist camera - limitations..............
Park Assist Pilot (PAP)*...........................
Park Assist Pilot (PAP)* - function..........
Park Assist Pilot (PAP)* - operation........
Park Assist Pilot (PAP)* - limitations.......
Active Park Assist (PAP)* - symbols and
messages................................................
BLIS........................................................
BLIS - operation......................................
CTA*........................................................
BLIS and CTA - symbols and messages
Speed related power steering.................
Type approval - radar system.................
240
241
241
243
243
244
244
245
247
249
249
250
250
252
Alcolock*.................................................
Alcolock* - functions and operation........
Alcolock* - storage..................................
Alcolock* - before starting the engine....
Alcolock* - to bear in mind.....................
Alcolock* - symbols and messages........
Starting the engine..................................
Switching off the engine.........................
Steering lock...........................................
Jump starting..........................................
Gearboxes...............................................
Manual gearbox......................................
Gear shift indicator*................................
Automatic gearbox - Geartronic*............
Automatic gearbox - Powershift*............
Gear selector inhibitor.............................
Hill start assist (HSA)*.............................
Start/Stop*..............................................
Start/Stop* - function and operation.......
Start/Stop* - the engine does not stop...
Start/Stop* - the engine auto-starts........
Start/Stop* - the engine does not autostart.........................................................
261
261
262
262
264
265
266
267
267
268
269
269
270
270
274
276
277
277
278
279
281
Start/Stop* - involuntary stop manual
gearbox...................................................
Start/Stop* - settings..............................
Start/Stop* - symbols and messages.....
ECO*.......................................................
Foot brake...............................................
Foot brake - anti-lock braking system....
Foot brake - emergency brake lights and
automatic hazard warning flashers.........
Foot brake - emergency brake assistance.......................................................
Parking brake..........................................
Driving in water.......................................
Overheating.............................................
Driving with open tailgate.......................
Overload - starter battery........................
Before a long journey..............................
Winter driving..........................................
Fuel filler flap - Opening/closing.............
Fuel filler flap - manual opening..............
Filling up with fuel...................................
Fuel - handling........................................
Fuel - petrol.............................................
Fuel - diesel.............................................
282
283
284
286
288
289
07 08 08
253
254
255
256
258
259
259
282
289
290
290
291
292
292
293
293
293
294
294
295
295
296
297
* Option/accessory, for more information, see Introduction.
7
Table of contents
09 Wheels and tyres
Catalytic converters................................
Filling with fuel - with a fuel can..............
Diesel particle filter (DPF)........................
Economical driving..................................
Driving with a trailer................................
Driving with a trailer - manual gearbox...
Driving with a trailer - automatic gearbox
Towing bracket.......................................
Detachable towbar - storage..................
Detachable towbar - specifications........
Detachable towbar - attachment/
removal...................................................
Trailer Stability Assist - TSA....................
Towing....................................................
Towing eye..............................................
Recovery.................................................
298
299
299
300
300
302
302
303
303
304
Tyres - direction of rotation....................
Tyres - maintenance...............................
Tyres - tread wear indicators..................
Wheel nuts..............................................
Jack........................................................
Winter tyres.............................................
Wheel and wheel rim dimensions...........
Tyres - dimensions..................................
Tyres - load index...................................
Tyres - speed ratings..............................
Spare wheel*...........................................
Changing wheels - taking out the spare
wheel*.....................................................
Changing wheels - removing wheels......
Changing wheels - fitting the spare
wheel*.....................................................
Tyres - air pressure.................................
Warning triangle......................................
First aid kit*.............................................
Tyre pressure monitoring*.......................
TPMS (Tyre Pressure Monitoring
System)* - general...................................
TPMS (Tyre Pressure Monitoring
System)* - adjusting (recalibration).........
312
312
314
314
315
315
316
316
316
317
317
TPMS (Tyre Pressure Monitoring
System)* status.......................................
TPMS (Tyre Pressure Monitoring
System)* - activate/deactivate................
TPMS (Tyre Pressure Monitoring
System)* - recommendations.................
TPMS (Tyre Pressure Monitoring
System)* - driveable punctured tyres*....
TPMS (Tyre Pressure Monitoring
System)* - rectifying low tyre pressure...
TM (Tyre Monitor)*..................................
Emergency puncture repair*...................
Emergency puncture repair kit* - location..........................................................
Emergency puncture repair kit* - overview.........................................................
Emergency puncture repair* - operation.
Emergency puncture repair* - rechecking...........................................................
Inflating tyres with the emergency puncture repair kit*..........................................
Emergency puncture repair* - stowing
components............................................
Emergency puncture repair kit* - sealant
Type approval - tyre pressure monitoring
08 09 09
8
304
307
308
309
310
* Option/accessory, for more information, see Introduction.
318
319
320
322
323
324
324
325
326
326
327
328
328
329
329
331
332
333
334
335
336
337
338
339
Table of contents
10 Maintenance and service
Volvo service programme....................... 346
Book service and repair*......................... 346
Raising the car........................................ 349
Bonnet - opening and closing................. 351
Engine compartment - overview............. 351
Engine compartment - checking............. 352
Engine oil - general................................. 353
Engine oil - checking and filling.............. 354
Coolant - level......................................... 357
Brake and clutch fluid - level.................. 358
Climate control system - fault tracing and
repair....................................................... 359
Lamp replacement - general................... 359
Lamp replacement - location of front
lamps...................................................... 360
Lamp replacement - headlamps............. 361
Lamp replacement - cover for main/
dipped beam bulbs................................. 361
Lamp replacement - dipped beam......... 362
Lamp replacement - main beam............. 362
Lamp replacement - extra main beam.... 362
Lamp replacement - direction indicators
front......................................................... 363
Lamp replacement - position/parking
lamps front.............................................. 363
Lamp replacement - daytime running
lights.......................................................
Lamp replacement - location of rear
lamps......................................................
Lamp replacement - direction indicators
rear, brake lights and reversing lamp.....
Lamp replacement - rear fog lamp.........
Lamp replacement - vanity mirror lighting...........................................................
Lamps - specifications ...........................
Wiper blades...........................................
Washer fluid - filling................................
Starter battery - general..........................
Battery - symbols....................................
Starter battery - replacement..................
Battery - Start/Stop.................................
Electrical system.....................................
Fuses - general.......................................
Fuses - in engine compartment..............
Fuses - under glovebox..........................
Fuses - under the right-hand front seat..
Car washing............................................
Polishing and waxing..............................
Water and dirt-repellent coating.............
Rustproofing...........................................
363
Cleaning the interior................................ 388
Paint damage.......................................... 389
364
10 10 10
364
365
365
366
366
369
369
371
372
372
374
374
376
380
383
385
386
387
387
* Option/accessory, for more information, see Introduction.
9
Table of contents
11 Specifications
Type designations...................................
Dimensions.............................................
Weights...................................................
Towing capacity and towball load..........
Engine specifications..............................
Engine oil - adverse driving conditions...
Engine oil - grade and volume................
Coolant - grade and volume...................
Transmission fluid - grade and volume...
Brake fluid - grade and volume...............
Washer fluid - quality and volume..........
Fuel tank - volume..................................
Air conditioning, fluid - volume and
grade.......................................................
Fuel consumption and CO2 emissions...
Tyres - approved tyre pressures.............
12 Alphabetical Index
392
394
395
396
398
399
400
402
403
404
404
405
Alphabetical Index.................................. 414
11 12
10
406
408
412
Table of contents
11
INTRODUCTION
01 Introduction
Owner information
Reading the owner's manual
Your car is equipped with a screen where you
can find information about how your car
works (applies to certain car models). For cars
with owner information in the screen, the printed owner's manual is a supplement and contains important text, the latest updates, as
well as instructions that can be useful when,
for practical reasons, you are unable to read
the information on the screen.
A good way of getting to know your new car
is to read the owner's manual, ideally before
your first journey. This will give you the opportunity to familiarise yourself with new functions, to see how best to handle the car in different situations, and to make the best use of
all the car's features. Please pay attention to
the safety instructions contained in the manual.
Changing the display language may mean that
some information does not correspond to
national or local laws and regulations.
The specifications, design features and illustrations in this owner's manual are not binding. We reserve the right to make modifications without prior notice.
IMPORTANT
The driver is always responsible that the
vehicle is driven safely in traffic and that
applicable laws and regulations are followed. It is also important that the car is
maintained and handled in accordance
with Volvo's recommendations in the
owner's information.
If there should be a difference between the
information on the screen and in the printed manual then it is always the printed
information that applies.
©
Volvo Car Corporation
Owner's Manual in mobile devices
NOTE
01
The owner's manual is available for download as a mobile application (applies for
certain car models and mobile devices),
see www.volvocars.com.
The mobile application also includes video
and searchable content and easy navigation between different sections.
Options/accessories
All types of option/accessory are marked with
an asterisk*.
In addition to standard equipment, the
owner's manual also describes options (factory fitted equipment) and certain accessories
(retrofitted extra equipment).
The equipment described in the owner's
manual is not available in all cars - they have
different equipment depending on adaptations for the needs of different markets and
national or local laws and regulations.
In the event of uncertainty over what is standard or an option/accessory, contact a Volvo
dealer.
Special texts
WARNING
Warning texts appear if there is a risk of
injury.
}}
* Option/accessory, for more information, see Introduction.
13
01 Introduction
01
||
IMPORTANT
Warning for personal injury
Risk of property damage
"Important" texts appear if there is a risk of
damage.
NOTE
NOTE texts give advice or tips that facilitate the use of features and functions for
example.
There is footnote information in the owner's
manual that is located at the bottom of the
page. This information is an addition to the
text that it refers to via a number. If the footnote refers to text in a table then letters are
used instead of numbers for referral.
Message texts
There are displays in the car that show text
messages. These text messages are highlighted in the owner's manual by means of
the text being slightly larger and printed in
grey. Examples of this are in menu texts and
message texts on the information display
(e.g. Audio settings).
Decals
The car contains different types of decal
which are designed to convey important
information in a simple and clear manner. The
decals in the car have the following descending degree of importance for the warning/
information.
14
G031592
Footnote
G031590
Black ISO symbols on yellow warning field,
white text/image on black message field.
Used to indicate the presence of danger
which, if the warning is ignored, may result in
serious personal injury or fatality.
White ISO symbols and white text/image on
black or blue warning field and message field.
Used to indicate the presence of danger
which, if the warning is ignored, may result in
damage to property.
01 Introduction
Information
When there is a series of illustrations for
step-by-step instructions each step is
numbered in the same way as the corresponding illustration.
There are numbered lists with letters
adjacent to the series of illustrations
where the order of the instructions is not
significant.
Arrows appear numbered and unnumbered and are used to illustrate a movement.
G031593
Arrows with letters are used to clarify a
movement when the reciprocal order is of
no relevance.
White ISO symbols and white text/image on
black message field.
NOTE
It is not intended that the decals illustrated
in the owner's manual should be exact
replicas of those in the car. They are
included to show their approximate
appearance and location in the car. The
information that applies to your particular
car is available on the respective decals
for your car.
Procedure lists
Procedures where action must be taken in a
certain sequence are numbered in the
owner's manual.
If there is no series of illustrations for step-bystep instructions then the different steps are
numbered with normal numbers.
Position lists
Red circles containing a number are used
in overview images where different components are pointed out. The number
recurs in the position list featured in connection with the illustration that describes
the item.
Related information
01
Related information refers to other sections
containing related information.
Images
The manual's images are sometimes schematic and may deviate from the car's appearance depending on equipment level and market.
To be continued
}} This symbol is located furthest down to
the right when an article continues on the following page.
Continued from previous page
|| This symbol is located furthest up to the
left when an article continues from the previous page.
Related information
•
The owner's manual and the environment
(p. 23)
•
Information on the Internet (p. 19)
Bulleted lists
A bulleted list is used when there is a list of
points in the owner's manual.
Example:
•
•
Coolant
Engine oil
15
01 Introduction
01
Digital owner's manual in the car
The owner's manual can be read on the
screen in the car1. The content is searchable
and it is easy to navigate between different
sections.
Open the digital owner's manual - press the
MY CAR button in the centre console, press
OK/MENU and select Owner's manual.
For basic navigation, see Operating the system. See below for a more detailed description.
• Search - Search function for finding an
article.
Search
• Categories - All articles sorted into categories.
• Favourites - Quick access to favouritebookmarked articles.
•
Quick Guide - A selection of articles for
common functions.
Select the information symbol in the lower
right-hand corner in order to obtain information about the digital owner's manual.
NOTE
The owner's manual is not available while
driving.
Searching using the daisy wheel.
Character list.
Changing the input mode (see following
table).
Use the daisy wheel to enter a search term,
e.g. "seatbelt".
1. Turn TUNE to the desired letter, press
OK/MENU to confirm. The number and
letter buttons on the control panel in the
centre console can also be used.
Owner's manual, start page.
There are four options for finding information
in the owner's manual:
1
16
Applies to certain car models.
2. Continue with the next letter and so on.
01 Introduction
3. To change the input mode to numbers or
special characters, or to perform a
search, turn TUNE to one of the options
(see explanation in the following table) in
the list for changing the input mode (2),
press OK/MENU.
Categories
Change between letters and
numbers with OK/MENU.
MORE
Change to special characters
with OK/MENU.
OK
Perform the search. Turn TUNE
to select a search result article,
press OK/MENU to go to the
article.
Located here are the articles that are saved
as favourites. To select an article as a favourite, see the heading "Navigating in an article"
below.
Changes between lowercase
and uppercase letters with OK/
MENU.
Turn TUNE to navigate in the favourite list
and press OK/MENU to open an article.
Press EXIT to go back to the previous view.
||}
Changes from the text wheel to
the search field. Move the cursor with TUNE. Delete any misspelling with EXIT. To return to
the text wheel, press OK/
MENU.
Note that the digit and letter
buttons on the control panel
can be used for editing in the
search field.
01
Turn TUNE to navigate in the category tree
and press OK/MENU to open a category - or article - selected
. Press
selected
EXIT to go back to the previous view.
123/AB
C
a|A
Navigating in an article
The articles in the owner's manual are structured into main categories and subcategories.
The same article can be in several appropriate categories in order to be found more
easily.
Favourites
Quick Guide
Located here is a selection of articles for getting to know the car's most common functions. The articles can also be accessed via
categories, but are collected here for quick
access.
Turn TUNE to navigate in the Quick Guide
and press OK/MENU to open an article.
Press EXIT to go back to the previous view.
Home - leads to the start page for the
owner's manual.
Favourite - adds/removes an article as a
favourite. You can also press the FAV
button in the centre console to add/
remove an article as a favourite.
Highlighted link - leads to linked article.
Special texts - if the article contains
warnings, important or note texts then an
associated symbol is shown here as well
as the number of such texts in the article.
Turn TUNE to navigate between the links or
scroll in an article. When the screen has
scrolled to the start/end of an article the
home and favourite options are accessed by
scrolling a further step up/down. Press OK/
MENU to activate the selection/highlighted
link. Press EXIT to go back to the previous
view.
}}
17
01 Introduction
01
||
Related information
•
Information on the Internet (p. 19)
Recording data
Certain information about the vehicle's operation and functionality, and any incidents, are
recorded in the car.
Your vehicle contains a number of computers
whose function is to continuously check and
monitor the vehicle's operation and functionality. Some of the computers can record
information during normal driving if they
detect an error. In addition, information is
recorded in the event of a collision or incident. Parts of the recorded information are
required so that technicians can diagnose
and rectify faults in the vehicle during servicing and maintenance and so that Volvo can
fulfil legal requirements and other regulations.
In addition to this, the information is used for
research purposes by Volvo in order to continually develop quality and safety, as the
information can contribute to a better understanding of the factors that cause accidents
and injuries. The information includes details
of the status and functionality of various systems and modules in the vehicle with regard
to engine, throttle, steering and brake systems, amongst other things. This information
may include details regarding the way the
driver drives the vehicle, such as vehicle
speed, brake and accelerator pedal use,
steering wheel movement and whether or not
the driver and passengers have used their
seatbelts. For the reasons given this information may be stored in the vehicle's computers
18
for a certain length of time, but also as a
result of a collision or incident. This information may be stored by Volvo as long as it can
help to further develop and further enhance
safety and quality and as long as there are
legal requirements and other regulations that
Volvo needs to consider.
Volvo will not contribute to the above-described information being disclosed to third parties without the vehicle owner's consent.
However, due to national legislation and regulations Volvo may be required to disclose
such information to authorities such as police
authorities, or others who may assert a legal
right to have access to it.
To be able to read and interpret the information recorded by the computers in the vehicle
requires special technical equipment that
Volvo, and workshops that have entered into
agreements with Volvo, have access to. Volvo
is responsible that the information, which is
transferred to Volvo during servicing and
maintenance, is stored and handled in a
secure manner and that the handling complies with applicable legal requirements. For
further information - contact a Volvo dealer.
01 Introduction
Accessories and extra equipment
The incorrect connection and installation of
accessories and extra equipment can negatively affect the car's electronic system.
Certain accessories only function when associated software is installed in the car's computer system. Volvo therefore recommends
that you always contact an authorised Volvo
workshop before installing accessories or
extra equipment which are connected to or
affect the electrical system.
Heat-reflecting windscreen*
Information on the Internet
Dimensions
A
65 mm
B
150 mm
C
125 mm
01
At www.volvocars.com there is further information concerning your car.
With a personal Volvo ID it is possible to log in
to My Volvo which is a personal web page for
you and your car.
The windscreen is equipped with a heatreflecting film (IR) that reduces the solar heat
radiation into the passenger compartment.
The positioning of electronic equipment, such
as a transponder, behind a glass surface with
heat-reflecting film may affect its function and
performance.
For the optimal function of electronic equipment, it should be positioned on the part of
the windscreen with no heat-reflecting film
(see the highlighted area in the above illustration).
QR code
A QR code reader is required to read the QR
code, which is available as a supplemental
program (app) for several mobile phones. The
QR code reader can be downloaded from e.g.
App Store, Windows Phone or Google Play.
Areas where IR film is not applied.
* Option/accessory, for more information, see Introduction.
19
01 Introduction
01
Volvo ID
Create a Volvo ID
Volvo ID is your personal ID that provides
access to various services2.
To create a Volvo ID you need to enter your
personal e-mail address and follow the
instructions in the e-mail message received in
order to complete the registration. It is possible to create a Volvo ID via one of the following services:
Examples of services:
•
My Volvo - Your personal web page for
you and your car.
•
In an Internet-connected car* - Certain
functions and services require that you
have registered your car to a personal
Volvo ID, for example to be able to send a
new address from a map service on the
Internet directly to the car.
•
Old login accounts must be upgraded to
Volvo ID in order to continue using these
services.
Advantages of Volvo ID
20
My Volvo web - Enter your e-mail address
and follow the instructions.
•
For an Internet-connected car* - Enter
your e-mail address in the app that
requires Volvo ID and follow the instructions. Alternatively, press the Connect
button
in the centre console and
select Apps, SETUP and follow the
instructions.
•
Volvo On Call, VOC* - Download the latest version of the VOC app. Choose to
create a Volvo ID from the start page and
follow the instructions.
Volvo On Call, VOC* - Volvo ID is used
when logging in to the Volvo On Call
mobile app.
NOTE
•
One user name and one password to
access online services, i.e. only one username and one password to remember.
•
When changing the username/password
for a service (e.g. VOC) it will also be
changed automatically for other services
(e.g. My Volvo)
2
•
Related information
•
Information on the Internet (p. 19)
The services available may vary over time and vary depending on equipment level and market.
* Option/accessory, for more information, see Introduction.
01 Introduction
Volvo Cars' environmental philosophy
01
tured in one of the cleanest and most
resource-efficient plants in the world.
G000000
Your Volvo complies with strict international
environmental standards and is also manufac-
Environmental care is one of Volvo Car Corporation's core values which influence all
operations. We also believe that our customers share our consideration for the environment.
Your Volvo complies with strict international
environmental standards and is also manufactured in one of the cleanest and most
resource-efficient plants in the world. Volvo
Car Corporation has global ISO certification,
which includes the environmental standard
ISO 14001 covering all factories and several
of our other units. We also set requirements
for our partners so that they work systematically with environmental issues.
Fuel consumption
Volvo cars have competitive fuel consumption in each of their respective classes. Lower
fuel consumption generally results in lower
emission of the greenhouse gas, carbon dioxide.
It is possible for the driver to influence fuel
consumption. For more information read
under the heading, Reducing environmental
impact.
Efficient emission control
Your Volvo is manufactured following the
concept "Clean inside and out" – a concept
that encompasses a clean interior environment as well as highly efficient emission control. In many cases the exhaust emissions are
well below the applicable standards.
Clean air in the passenger
compartment
A passenger compartment filter prevents dust
and pollen from entering the passenger compartment via the air intake.
}}
21
01 Introduction
01
||
A sophisticated air quality system, IAQS*
(Interior Air Quality System) ensures that the
incoming air is cleaner than the air in the traffic outside.
The system consists of an electronic sensor
and a carbon filter. The incoming air is monitored continuously and if there is an increase
in the level of certain unhealthy gases such as
carbon monoxide then the air intake is
closed. Such a situation may arise in heavy
traffic, queues and tunnels for example.
The entry of nitrous oxides, ground-level
ozone and hydrocarbons is prevented by the
carbon filter.
Interior
The interior of a Volvo is designed to be pleasant and comfortable, even for people with
contact allergies and for asthma sufferers.
Extreme attention has been given to choosing
environmentally-compatible materials.
required to guarantee good environmental
care.
Reducing environmental impact
You can easily help reduce environmental
impact - here are a few tips:
•
•
•
Drive economically - think ahead.
•
If the car is equipped with an engine
block heater*, use it before starting from
cold - it improves starting capacity and
reduces wear in cold weather and the
engine reaches normal operating temperature more quickly, which lowers consumption and reduces emissions.
•
High speed increases consumption considerably due to increased wind resistance - a doubling of speed increases
wind resistance 4 times.
•
Always dispose of environmentally hazardous waste, such as batteries and oils, in
an environmentally safe manner. Consult
a workshop in the event of uncertainty
about how this type of waste should be
discarded - an authorised Volvo workshop is recommended.
Volvo workshops and the environment
Regular maintenance creates the conditions
for a long service life and low fuel consumption for your car. In this way you contribute to
a cleaner environment. When Volvo's workshops are entrusted with the service and
maintenance of your car it becomes part of
our system. Volvo makes clear demands
regarding the way in which our workshops
are designed in order to prevent spills and
discharges into the environment. Our workshop staff have the knowledge and the tools
22
Avoid letting the engine idle - switch off
the engine when stationary for longer
periods. Pay attention to local regulations.
* Option/accessory, for more information, see Introduction.
Perform service and maintenance in
accordance with the owner's manual's
instructions - follow the intervals recommended in the Service and Warranty
Booklet.
Following this advice can save money, the
planet's resources are saved, and the car's
durability is extended. For more information
and further advice, see Eco guide (p. 65),
Economical driving (p. 300) and Fuel consumption (p. 408).
Recycling
As a part of Volvo's environmental work, it is
important that the car is recycled in an environmentally sound manner. Almost all of the
car can be recycled. The last owner of the car
is therefore requested to contact a dealer for
referral to a certified/approved recycling
facility.
Related information
•
The owner's manual and the environment
(p. 23)
01 Introduction
The owner's manual and the
environment
The paper pulp in a printed owner's manual
comes from FSC® certified forests or other
controlled sources.
The Forest Stewardship Council® symbol
shows that the paper pulp in a printed
owner's manual comes from FSC® certified
forests or other controlled sources.
01
Laminated glass
Laminated glass
The glass is reinforced which provides better protection against
break-ins and improved sound insulation in the passenger compartment. The windscreen and other windows*
have laminated glass.
Related information
•
Volvo Cars' environmental philosophy
(p. 21)
* Option/accessory, for more information, see Introduction.
23
SAFETY
02 Safety
General information on seatbelts
Heavy braking can have serious consequences if the seatbelts are not used. Ensure that
all passengers are using their seatbelts during
the journey.
Remember
•
•
Do not use clips or anything else that can
prevent the seatbelt from fitting properly.
The seatbelt must not be twisted or
caught on anything.
Related information
•
•
•
Seatbelt - pregnancy (p. 27)
Seatbelt - loosening (p. 27)
Seatbelt tensioner (p. 28)
02
WARNING
The seatbelts and airbags interact. If a
seatbelt is not used or is used incorrectly,
this may diminish the protection provided
by the airbag in the event of a collision.
WARNING
Each seatbelt is designed for only one person.
Tension the hip strap over the lap by pulling the
diagonal shoulder belt up towards the shoulder.
The hip strap must be positioned low down (not
over the abdomen).
It is important that the seatbelt lies against
the body so it can provide maximum protection. Do not lean the backrest too far back.
The seatbelt is designed to protect in a normal seating position.
Unbelted occupants will be reminded to fasten their (p. 26) seatbelt by means of an
audio and visual reminder (p. 28).
WARNING
Never modify or repair the seatbelts yourself. Volvo recommends that you contact
an authorised Volvo workshop.
If the seatbelt has been subjected to a
major load, such as in conjunction with a
collision, the entire seatbelt must be
replaced. Some of the seatbelt's protective
properties may have been lost even if the
seatbelt does not appear damaged. The
seatbelt must also be replaced if it shows
signs of wear or damage. The new seatbelt
must be type-approved and designed for
installation at the same location as the
replaced seatbelt.
25
02 Safety
02
Seatbelt - putting on
Remember
Put on the seatbelt (p. 25) before driving
starts.
The seatbelt locks and cannot be withdrawn:
•
•
•
Pull the belt out slowly and secure it by
pressing its locking tab into the seatbelt
buckle. A loud "click" indicates that the belt
has locked.
if the car leans heavily.
Related information
Incorrectly fitted seatbelt. The belt must rest on
the shoulder.
Correctly fitted seatbelt.
Seatbelt height adjustment. Press the button and
move the belt vertically. Position the belt as high
as possible without it chafing against your throat.
The locking tab at the centre rear seat only
fits into the intended seatbelt buckle.
26
if it is pulled out too quickly
during braking and acceleration
•
•
•
•
Seatbelt - pregnancy (p. 27)
Seatbelt - loosening (p. 27)
Seatbelt tensioner (p. 28)
Seatbelt reminder (p. 28)
02 Safety
Seatbelt - loosening
Seatbelt - pregnancy
Loosen the seatbelt (p. 25) when the car is
stationary.
Seatbelt (p. 25) must always be worn during
pregnancy. But it is crucial that it be worn in
the correct way.
Press the red button on the seatbelt buckle
and then let the belt retract. If the seatbelt
does not retract fully, feed it in by hand so
that it does not hang loose.
The aim should be to position the seat with as
large a distance as possible between abdomen and steering wheel.
Related information
•
•
Seatbelt - putting on (p. 26)
02
Seatbelt - loosening (p. 27)
Related information
Seatbelt - putting on (p. 26)
Seatbelt reminder (p. 28)
G020998
•
•
The diagonal section should wrap over the
shoulder then be routed between the breasts
and to the side of the abdomen.
The lap section should lay flat over the thighs
and as low as possible under the abdomen. –
It must never be allowed to ride upward.
Remove the slack from the seatbelt and
ensure that it fits as close to the body as possible. In addition, check that there are no
twists in the seatbelt.
As the pregnancy progresses, pregnant drivers must adjust the seat (p. 77) and steering wheel (p. 82) such that they can easily
maintain control of the vehicle as they drive
(which means that they must be able to easily
operate the foot pedals and steering wheel).
27
02 Safety
Seatbelt reminder
02
automatically after approximately
30 seconds driving or after pressing the
indicator stalk OK button (p. 105). If anyone is unbelted then the message can
only be acknowledged manually by
pressing the indicator stalk OK button.
Unbelted occupants will be reminded to fasten their (p. 26) seatbelt by means of an audio
and visual reminder.
•
Provides a warning if one of the rear seatbelts is unfastened during travel. This
warning takes the form of a message in
the combined instrument panel along with
the audio/visual signal. The warning stops
when the seatbelt is re-fastened, or it can
also be acknowledged manually by
pressing the OK button.
Seatbelt tensioner
Seatbelts (p. 25) on the driver's side, the passenger side and at the outer rear seats are fitted with seatbelt tensioners. A mechanism in
the seatbelt tensioner tightens the seatbelt in
the event of a sufficiently violent collision. The
seatbelt then provides more effective restraint
for the occupants.
WARNING
Never insert the tongue of the passenger's
seatbelt into the buckle on the driver's
side. Always insert the tongue of the seatbelt into the buckle on the correct side. Do
not make any damages on seatbelts nor
insert any foreign objects into a buckle.
The seatbelts and buckles would then
possibly not function as intended in the
event of a collision. There is a risk of
serous injury.
The combined instrument panel's information
display shows which seatbelts are in use.
This information is always available.
The audio reminder is speed dependent, and
in some cases time dependent. The visual
reminder is located in the roof console and in
the combined instrument panel (p. 61).
Child seats are not covered by the seatbelt
reminder system.
Rear seat
The seatbelt reminder in the rear seat has two
subfunctions:
•
28
Provides information on which seatbelts
(p. 25) are being used in the rear seat. A
message appears in the combined instrument panel when the seatbelts are in use,
or if one of the rear doors has been
opened. The message is acknowledged
Related information
•
General information on seatbelts (p. 25)
02 Safety
Safety - warning symbol
WARNING
The warning symbol is shown if a fault is
detected during fault tracing or if a system
has been activated. Where required, the
warning symbol is shown together with a
message in the combined instrument panel
(p. 61) information display.
If the warning symbol for the airbag system remains illuminated or illuminates
while driving, it means that the airbag system does not have full functionality. The
symbol indicates a fault in the airbag system, the belt tensioner system, SIPS, the
IC system or some other fault in the system. Volvo recommends that you contact
an authorised Volvo workshop immediately.
Warning triangle and warning symbol for the airbag system in the digital combined instrument
panel.
Warning triangle and warning symbol for the airbag system (p. 30) in the analogue combined
instrument panel.
02
Related information
•
General information on safety mode
(p. 40)
The warning symbol in the combined instrument panel is switched on with the remote
control key in key position II (p. 76), fault
tracing is performed each time the ignition is
switched on. The symbol clears after
approx. 6 seconds provided the airbag system is fault-free.
The warning symbol is shown if a fault is
detected during fault tracing or if a system
has been activated. Where required, the
warning symbol is shown together with a
message in the display. If the warning symbol
malfunctions, the warning triangle illuminates
and SRS airbag Service required or SRS
airbag Service urgent appears in the display. Volvo recommends that you contact an
authorised Volvo workshop immediately.
29
02 Safety
Airbag system
02
The system consists of airbags and sensors.
A sufficiently violent collision trips the sensors
and the airbag(s) are inflated and become
hot. The airbag cushions the initial collision
impact for the occupant. The airbag deflates
when compressed by the collision. When this
occurs, smoke escapes into the car. This is
completely normal. The entire process,
including inflation and deflation of the airbag,
occurs within tenths of a second.
In the event of a frontal collision the airbag
system helps to protect the head, face and
chest of the driver and passenger.
G018665
WARNING
Airbag system viewed from above, left-handdrive car.
Volvo recommends that you contact an
authorised Volvo workshop for repair.
Defective work in the airbag system could
cause malfunction and result in serious
personal injury.
NOTE
G018666
The detectors react differently depending
on the nature of the collision and whether
or not the seatbelt is fastened. Applies to
all seatbelt positions apart from centre
seat rear.
Airbag system viewed from above, right-handdrive car.
30
It is therefore possible that only one (or
none) of the airbags may inflate in a collision. The detectors sense the force of the
collision on the vehicle and the action is
adapted accordingly so that one or more
airbags are deployed.
Related information
•
•
•
Airbags on driver's side (p. 31)
Passenger airbag (p. 31)
Safety - warning symbol (p. 29)
02 Safety
Airbags on driver's side
To supplement the protection afforded by the
seatbelt (p. 25) on the driver side, the car is
equipped with two airbags (p. 30).
Related information
•
Passenger airbag (p. 31)
Passenger airbag
To supplement the protection afforded by the
seatbelt (p. 25) on the passenger side, the car
is equipped with an airbag (p. 30).
One of the airbags is folded up into the centre
of the steering wheel. The steering wheel is
marked AIRBAG.
The airbag is folded up into a compartment
above the glovebox. Its cover panel is
marked AIRBAG.
Knee airbag on the driver's side in a left-handdrive car.
Location of the front passenger airbag in a lefthand drive car.
02
The second airbag (at knee level) is fitted in
the lower part of the instrument panel on the
driver's side; this panel is labelled AIRBAG.
WARNING
The seatbelts and airbags interact. If the
belt is not used or is used incorrectly, this
may diminish the protection provided by
the airbags in the event of a collision.
}}
31
02 Safety
||
WARNING
Do not put objects in front of or above the
dashboard where the passenger airbag is
located.
02
WARNING
Never place a child in a child seat or on a
booster cushion in the front seat if the airbag is activated.
Location of the front passenger airbag in a righthand drive car.
The warning label for the passenger airbag is
fitted in one of the following two locations in
the car:
Alternative 2: Position of airbag label on passenger side door pillar. The label becomes visible
when the passenger door is opened.
WARNING
Never use a rear-facing child seat on a
seat protected by an activated airbag. Failure to follow this advice can lead to death
or serious injury to the child.
WARNING
The seatbelts and airbags interact. If the
belt is not used or is used incorrectly, this
may diminish the protection provided by
the airbag in the event of a collision.
Alternative 1: Position of airbag label on passenger side sun visor.
32
To minimise the risk of injury if the airbag
deploys, passengers must sit as upright as
possible with their feet on the floor and
backs against the backrest. Seatbelts
must be secured.
* Option/accessory, for more information, see Introduction.
Never allow anybody to stand or sit in front
of the front passenger seat.
No one shorter than 140 cm should ever
sit in the front passenger seat if the airbag
is activated.
Failure to follow the advice given above
can endanger life.
Switch - PACOS*
The front passenger airbag can be deactivated (p. 33) if the car is equipped with a
switch, PACOS (Passenger Airbag Cut Off
Switch).
WARNING
If the car is equipped with a front passenger airbag, but does not have a PACOS
switch (Passenger Airbag Cut Off Switch),
then the airbag will always be activated.
02 Safety
Related information
•
•
Airbags on driver's side (p. 31)
Child seats (p. 45)
Passenger airbag - activating/
deactivating*
never children in a child seat or on a
booster cushion.
Front passenger airbag (p. 31) can be deactivated if the car is equipped with a switch,
PACOS (Passenger Airbag Cut Off Switch).
The airbag is deactivated. With the switch
in this position, children in a child seat or
on a booster cushion can sit in the front
passenger seat, but never persons taller
than 140 cm.
Switch - PACOS
The switch for the passenger airbag (PACOS)
is located on the passenger end of the instrument panel and is accessible when the passenger door is open.
Activated airbag (passenger seat):
Check that the switch is in the required position. The remote control key's key blade
(p. 164) should be used to change position.
Never place a child in a child seat or on a
booster cushion on the front passenger
seat when the airbag is activated. This
applies to everyone shorter than 140 cm.
02
WARNING
Deactivated airbag (passenger seat):
No one taller than 140 cm should ever sit
in the front passenger seat when the airbag is deactivated.
Failure to follow the advice given above
can endanger life.
NOTE
Location of airbag switch.
The airbag is activated. With the switch in
this position, persons taller than 140 cm
can sit in the front passenger seat, but
When the remote control key is in key
position II (p. 76) the warning symbol
(p. 29) for the airbag is shown in the combined instrument panel for
approx. 6 seconds.
Following which, the indicator in the roof
console is illuminated showing the correct
status for the front passenger seat airbag.
}}
* Option/accessory, for more information, see Introduction.
33
02 Safety
||
WARNING
Failure to follow the advice given above
can endanger the lives of passengers in
the car.
02
Related information
•
Indicator showing that the passenger airbag is
activated.
Indicator showing that the passenger airbag is
deactivated.
A text message and a warning symbol in the
roof console indicate that the airbag for the
front passenger seat is activated (see preceding illustration).
A text message and a symbol in the roof console indicate that the airbag for the front passenger seat is deactivated (see preceding
illustration).
WARNING
Never place a child in a child seat or on a
booster cushion in the front seat if the airbag is activated and the symbol
in
the roof console is illuminated. Failure to
follow this advice could endanger the life
of the child.
34
WARNING
Do not allow anyone to sit in the front passenger seat if the message in the roof console indicates that the airbag is deactivated, and if the warning symbol (p. 29) for
the airbag system is also displayed on the
combined instrument panel. This indicates
that there has been a severe malfunction.
Visit a workshop as soon as possible.
Volvo recommends that you contact an
authorised Volvo workshop.
Child seats (p. 45)
02 Safety
Side airbag (SIPS)
WARNING
In a side impact collision a large proportion of
the collision force is transferred by the SIPS
(Side Impact Protection System) to beams,
pillars, the floor, the roof and other structural
parts of the body. The side airbags at the driver's and front passenger seats protect the
chest area and the hip and are an important
part of the SIPS.
•
Volvo recommends that repairs are
only carried out by an authorised Volvo
workshop. Defective work in the SIPSbag system could cause malfunction
and result in serious personal injury.
•
Do not put objects in the area between
the outside of the seat and the door
panel, since this area is required by
the side airbag.
•
Volvo recommends the use only of car
seat covers approved by Volvo. Other
seat covers may impede the operation
of the side airbags.
•
Side airbags are a supplement the
seatbelts. Always use a seatbelt.
Driver's seat, left-hand drive.
02
Related information
The SIPS bag system consists of two main
components, side airbag and sensors. The
side airbags are located in the front seat's
backrests.
•
•
•
Passenger airbag (p. 31)
•
Inflatable Curtain (IC) (p. 36)
Airbags on driver's side (p. 31)
Side airbag (SIPS) - child seat/booster
cushion (p. 36)
Front passenger seat, left-hand drive.
A sufficiently violent collision trips the sensors
and the side airbags are inflated. The airbag
inflates between the occupant and the door
panel and thereby cushions the initial impact.
The airbag deflates when compressed by the
collision. The side airbag is normally only
deployed on the side of the collision.
35
02 Safety
Side airbag (SIPS) - child seat/booster
cushion
02
The protection provided by the car to children
seated in a child seat or on a booster cushion
is not diminished by the side airbag (p. 35).
Inflatable Curtain (IC)
WARNING
The inflatable curtain helps to prevent the
driver and passengers from striking their
heads on the inside of the car during a collision.
Never hang or attach heavy items onto the
handles in the roof. The hook is only
designed for light clothing (not for solid
objects such as umbrellas for example).
Do not screw or install anything onto the
car's headlining, door pillars or side panels. This could compromise the intended
protection. Volvo recommends that you
only ever use Volvo genuine parts that are
approved for placement in these areas.
Child seat/booster cushion (p. 45) can be
placed on the front passenger seat provided
that the car does not have an activated airbag
(p. 33) on the front passenger side.
Related information
•
•
Passenger airbag (p. 31)
WARNING
General information on child safety
(p. 44)
Do not load the car higher than 50 mm
under the top edge of the windows in the
doors. Otherwise, the intended protection
of the inflatable curtain, which is concealed in the headlining, may be compromised.
The inflatable curtain IC (Inflatable Curtain) is
a part of the SIPS system (p. 35). It is fitted in
the headlining along both sides of the roof
and protects the car's occupants sitting in the
outer seats. A sufficiently violent collision
trips the sensors and the inflatable curtain is
inflated.
WARNING
The inflatable curtain is a supplement to
the seatbelts.
Always use a seatbelt.
Related information
•
•
•
36
General information on seatbelts (p. 25)
Airbag system (p. 30)
Side airbag (SIPS) (p. 35)
02 Safety
General information on WHIPS
(whiplash protection)
WARNING
The WHIPS system is a supplement to the
seatbelts. Always use a seatbelt.
WHIPS (Whiplash Protection System) is a protection against whiplash injuries. The system
consists of energy absorbing backrests and
specially designed head restraints in the front
seats.
Seat properties
02
When the WHIPS system is deployed, the
front seat backrests are lowered backward to
change the seating position of the driver and
front seat passenger. This reduces the risk of
whiplash injury.
WARNING
Never modify or repair the seat or WHIPS
system yourself. Volvo recommends that
you contact an authorised Volvo workshop.
Related information
•
•
•
WHIPS - child seats (p. 38)
WHIPS - seating position (p. 38)
General information on seatbelts (p. 25)
The WHIPS system is actuated by a rear-end
collision, where the angle and speed of the
collision, and the nature of the colliding vehicle all have an influence.
37
02 Safety
02
WHIPS - child seats
WHIPS - seating position
The protection provided by the car to children
seated in a child seat or on a booster cushion
is not diminished by the WHIPS system
(p. 37).
In order to obtain optimum protection from
the WHIPS system (p. 37) the driver and passenger must have the correct seating position
and make sure that the system's function is
not obstructed.
Child seat/booster cushion (p. 45) can be
placed on the front passenger seat provided
that the car does not have an activated airbag
(p. 33) on the front passenger side.
Related information
•
General information on child safety
(p. 44)
WARNING
Do not squeeze rigid objects between the
rear seat cushion and the front seat's
backrest. Make sure you do not to
obstruct the function of the WHIPS system.
Seating position
Set the correct seating position in the front
seat (p. 77) before driving starts.
Driver and front seat passenger should sit in
the centre of the seat with as little space as
possible between the head and the head
restraint.
Function
Do not place objects on the rear seat that may
prevent the WHIPS system from functioning.
WARNING
If a rear seat backrest is folded down, the
corresponding front seat must be moved
forward so that it does not touch the
folded backrest.
Do not leave any objects on the floor behind the
driver's seat/passenger seat that may prevent the
WHIPS system from functioning.
38
02 Safety
WARNING
If a seat has been subjected to extreme
forces, such as due to a rear-end collision,
the WHIPS system must be checked.
Volvo recommends that it is checked by
an authorised Volvo workshop.
Part of the WHIPS system's protective
capacity may have been lost even if the
seat appears to be undamaged.
Volvo recommends that you contact an
authorised Volvo workshop to have the
system checked even after a minor rearend collision.
When the systems deploy
In the event of a collision Volvo's different
personal safety systems work together in
order to minimise injury.
System
Triggered
Seatbelt tensioner (p. 28) front
seat
In the event of a
frontal collision,
and/or side-impact
collision, and/or
rear-end collision
and/or overturning
Seatbelt tensioner (p. 28) rear
seatA
In a frontal collision
and/or side-impact
accident and/or
overturning
Airbags
In a frontal collisionB
(Steering wheel,
knee (p. 31) and passenger airbag (p. 31))
Side airbags
(SIPS) (p. 35)
System
Triggered
Inflatable Curtain
IC (p. 36)
In the event of a
side impact and/or
overturning and/or
some frontal collisionsB
Whiplash protection
WHIPS (p. 37)
A
B
02
In a rear-end collision
There is no seatbelt tensioner at the centre rear seat.
The bodywork of the car could be greatly deformed in a
collision without airbag deployment. A number of factors
such as the rigidity and weight of the object hit, the speed
of the car, the angle of the collision etc. affects how the
different safety systems of the car are activated.
If the airbags (p. 30) have deployed, the following is recommended:
•
Recovering the car. Volvo recommends
that you have it conveyed to an authorised Volvo workshop. Do not drive with
deployed airbags.
•
Volvo recommends that you engage an
authorised Volvo workshop to handle the
replacement of components in the car's
safety systems.
•
Always contact a doctor.
In a side-impact
accidentB
NOTE
The airbags and belt tensioner system are
deployed only once during a collision.
}}
39
02 Safety
WARNING
02
The airbag system's control module is
located in the centre console. If the centre
console is drenched with water or other
liquid, disconnect the battery cables. Do
not attempt to start the car since the airbags may deploy. Recovering the car.
Volvo recommends that you have it conveyed to an authorised Volvo workshop.
General information on safety mode
Safety mode is a protective state that is
enforced when the collision may have damaged any of the car's vital functions, such as
the fuel lines, sensors for one of the safety
systems, or the brake system.
WARNING
Never drive with deployed airbags. They
can make steering difficult. Other safety
systems may also be damaged. The
smoke and dust created when the airbags
are deployed can cause skin and eye irritation/injury after intensive exposure. In case
of irritation, wash with cold water. The
rapid deployment sequence and airbag
fabric may cause friction and skin burns.
Warning triangle in the digital combined instrument panel.
Warning triangle in the analogue combined
instrument panel.
If the car is involved in a collision, the text
Safety mode See manual may appear in the
combined instrument panel (p. 61) information display. This means that the car has
reduced functionality.
WARNING
Never attempt to repair your car or reset
the electronics yourself if the car has been
in safety mode. This could result in personal injury or the car not functioning as
normal. Volvo recommends that you
engage an authorised Volvo workshop to
check and restore the car to normal status
after Safety mode See manual has been
displayed.
40
02 Safety
Related information
•
Safety mode - attempting to start the car
(p. 41)
•
Safety mode - moving the car (p. 42)
Safety mode - attempting to start the
car
WARNING
Never, under any circumstances, attempt
to restart the car if it smells of fuel when
the Safety mode See manual message
is displayed. Leave the car at once.
If the car is set in safety mode (p. 40) then an
attempt to start the car can be made if everything seems normal and the absence of fuel
leakage has been checked.
WARNING
First, check that no fuel is leaking from the
car. There must be no smell of fuel either.
If the car is in safety mode it must not be
towed. It must be transported from its
location. Volvo recommends that it is
transported to an authorised Volvo workshop.
If everything seems normal and you have
checked for indications of fuel leakage, you
may attempt to start the car.
Remove the remote control key and open the
driver's door. If a message is now shown to
the effect that the ignition is on, press the
start button. Then close the door and reinsert
the remote control key. The car's electronics
will now try to reset themselves to normal
mode. Then try to start the car.
02
Related information
•
Safety mode - moving the car (p. 42)
If the message Safety mode See manual is
still shown on the display, then the car must
not be driven or towed, but a vehicle recovery
service (p. 310) must be used instead. Even if
the car appears to be driveable, hidden damage may make the car impossible to control
once moving.
41
02 Safety
02
Safety mode - moving the car
Pedestrian airbag
If Normal mode is shown after Safety mode
See manual has been reset after attempting
to start the car (p. 41) , the car can be moved
carefully out of a dangerous position.
The airbag for pedestrians (Pedestrian Airbag)
contributes in certain frontal collisions to alleviating the collision of the pedestrian with the
car.
NOTE
There may be objects in the traffic environment that prompt a signal to the sensors
that is similar to a collision with a pedestrian. It is possible that the system will be
activated in the event of a collision with
such an object.
Do not move the car further than necessary.
Related information
•
If the airbag is activated (Pedestrian Airbag)
General information on safety mode
(p. 40)
•
•
•
the rear part of the bonnet is raised and
locked in this position
the hazard warning flashers are activated
the brake system is prepared for the
upcoming emergency braking.
WARNING
The pedestrian airbag (Pedestrian Airbag) is
fitted under the bonnet near the windscreen.
In the event of certain frontal collisions with a
pedestrian, the sensors in the front bumper
react and the airbag inflates if required, based
on the force of the impact. The sensors are
active at a speed of approx. 20-50 km/h and
an ambient temperature between
-20 and +70°C.
The sensors are designed to detect a collision
with an object that has similar properties to
those of the human leg.
42
Do not fit any accessories or change anything in the front. Incorrect intervention at
the front may cause incorrect function in
the system and lead to serious injury and
damage to the car.
Volvo recommends that genuine wiper
arms are used and that you only use genuine parts for them.
WARNING
Volvo recommends contacting an authorised Volvo workshop in the event of damage to the bumper in order to ensure that
the system is intact.
02 Safety
Related information
•
Pedestrian airbag - moving the car
(p. 43)
•
Pedestrian airbag - folding up (p. 43)
Pedestrian airbag - moving the car
Pedestrian airbag - folding up
The car may be moved if it has not been set in
safety mode (p. 40).
Pedestrian airbag (p. 42) (Pedestrain Airbag)
must be folded up before the car is moved.
If any of the other airbags in the passenger
compartment were activated then the car
remains in safety mode.
02
If only the pedestrian airbag (p. 42)
Pedestrian Airbag has been activated:
1. Move the car to a safe location as close
as possible.
2. Fold up the airbag in accordance with the
instructions (p. 43).
3. Seek the nearest workshop.
WARNING
Volvo recommends that, after activation of
the airbag, you contact an authorised
Volvo workshop as soon as possible.
Related information
•
Pedestrian airbag (p. 42)
Airbag (Pedestrian Airbag)
Airbag housing
Velcro strap, right-hand side
Velcro strap, left-hand side
The airbag may feel warm and give off
smoke. This is normal. Fold the airbag as follows:
1. Find the Velcro strap on the
left-hand side (4).
2. Gather the airbag fabric along its length
on the left-hand side. Then fold the gathered fabric towards the centre. Wind the
Velcro strap (double sided) around as
much fabric as possible and fasten it.
}}
43
02 Safety
||
3. Press the rolled up portion of the airbag
into the airbag housing (2).
02
4. Repeat points 1-3 for the right-hand side.
It may be necessary to fold the gathered
fabric twice on this side in order to wind
the Velcro strap around it.
5. The airbag housing cover will be open
slightly. This is completely normal.
Related information
•
Pedestrian airbag - moving the car (p. 43)
General information on child safety
Volvo recommends that children travel in
rear-facing child seats until as late an age as
possible, at least until 3-4 years of age, and
then front-facing booster cushions/child seats
until up to 10 years of age.
The position of a child in the car and the
choice of equipment are dictated by the
child's weight and size; see Child seats
(p. 45).
NOTE
Regulations regarding the placement of
children in cars vary from country to country. Check what does apply.
Volvo has child safety equipment (child seats,
booster cushions & attachment devices)
which is designed for your particular car.
Using Volvo's child safety equipment provides you with optimum conditions for your
child to travel safely in the car. Furthermore,
the child safety equipment fits and is easy to
use.
44
NOTE
Children of all ages and sizes must always sit
correctly secured in the car. Never allow a
child to sit on the knee of a passenger.
In the event of questions when fitting child
safety products, contact the manufacturer
for clearer instructions.
Child safety locks
The controls for operating the rear door
power windows and the rear door opening
handles can be blocked (p. 176) from opening from the inside.
Related information
•
•
•
•
Child seats (p. 45)
Child seats - location (p. 49)
Child seat - ISOFIX (p. 50)
Child seats - upper mounting points
(p. 53)
02 Safety
Child seats
NOTE
Children should sit comfortably and safely.
Make sure that the child seat is being used
correctly.
When using child safety products it is
important to read the installation instructions included.
02
WARNING
Do not secure the straps of the child seat
to the seat's horizontal adjustment bar,
springs or the rails and beams under the
seat. Sharp edges may damage the straps.
G020739
Look in the installation instructions for the
child seat for the correct fitting.
Child seats and airbags are not compatible.
}}
45
02 Safety
||
Recommended child seats1
Weight
02
Front seat (with deactivated airbag)
Group 0
Type approval: E1 04301146
Group 0+
(L)
max 13 kg
max 10 kg
Group 0+
max 13 kg
Centre rear
seat
Volvo infant seat (Volvo Infant Seat) - rear-facing child
seat, secured with the ISOFIX fixture system.
max 10 kg
Group 0
Outer rear seat
Volvo infant seat (Volvo Infant Seat) - rear-facing
child seat, secured with the car's seatbelt.
Volvo infant seat (Volvo Infant Seat) - rear-facing child
seat, secured with the car's seatbelt.
Type approval: E1 04301146
Type approval: E1 04301146
(U)
(U)
Volvo infant
seat (Volvo
Infant Seat) rear-facing child
seat, secured
with the car's
seatbelt.
Type approval:
E1 04301146
(U)
Group 0
Child seats which are universally
max 10 kg
(U)
approved.A
Child seats which are universally approved.
(U)
Group 0+
max 13 kg
1
46
With regard to other child seats your car should be included in the manufacturer's enclosed list of vehicles or be universally approved in accordance with the ECE R44 legal requirement.
02 Safety
Weight
Front seat (with deactivated airbag)
Outer rear seat
Group 1
Volvo rear-facing/turnable child seat (Volvo
Convertible Child Seat) - rear-facing child seat,
secured with the car's seatbelt and straps.
Volvo rear-facing/turnable child seat (Volvo Convertible
Child Seat) - rear-facing child seat, secured with the car's
seatbelt and straps.
Type approval: E5 04192
Type approval: E5 04192
9-18 kg
(L)
Child seats which are universally
9-18 kg
(U)
(U)
Group 2
Volvo rear-facing/turnable child seat (Volvo
Convertible Child Seat) - rear-facing child seat,
secured with the car's seatbelt and straps.
Volvo rear-facing/turnable child seat (Volvo Convertible
Child Seat) - rear-facing child seat, secured with the car's
seatbelt and straps.
Type approval: E5 04192
Type approval: E5 04192
(L)
(L)
Volvo rear-facing/turnable child seat (Volvo
Convertible Child Seat) - front-facing child seat,
secured with the car's seatbelt.
Volvo rear-facing/turnable child seat (Volvo Convertible
Child Seat) - front-facing child seat, secured with the
car's seatbelt.
Type approval: E5 04191
Type approval: E5 04191
(U)
(U)
Volvo booster seat with backrest (Volvo Booster
Seat with backrest).
Volvo booster seat with backrest (Volvo Booster Seat
with backrest).
Type approval: E1 04301169
Type approval: E1 04301169
(UF)
(UF)
Group 2
15-25 kg
Group 2/3
15-36 kg
02
(L)
Group 1
15-25 kg
Centre rear
seat
approved.A
Child seats which are universally approved.
}}
47
02 Safety
||
02
Weight
Front seat (with deactivated airbag)
Outer rear seat
Group 2/3
Booster cushion with and without backrest (Booster
Cushion with and without backrest).
Booster cushion with and without backrest (Booster
Cushion with and without backrest).
Type approval: E5 04216
Type approval: E5 04216
(UF)
(UF)
15-36 kg
Centre rear
seat
L: Suitable for specific child seats. These child seats may be intended for use in a special car model, limited or semi-universal categories.
U: Suitable for universally approved child seats in this weight class.
UF: Suitable for front-facing universally approved child seats in this weight class.
B: Built-in child seats approved for this weight class.
A
Only for rear-facing child seat. Set the seat's backrest in upright position.
Related information
•
•
•
•
48
Child seats - location (p. 49)
Child seats - upper mounting points
(p. 53)
Child seat - ISOFIX (p. 50)
General information on child safety (p. 44)
02 Safety
Child seats - location
WARNING
Always fit child seats/booster cushions (p. 45)
in the rear seat if the passenger airbag is activated (p. 33). If a child is sitting on the front
passenger seat then he/she could suffer serious injury if the airbag deploys.
Never place a child in a child seat or on a
booster cushion in the front seat if the airbag is activated.
Never allow anybody to stand or sit in front
of the front passenger seat.
The warning label for the passenger airbag is
fitted in one of the following two locations in
the car:
02
No one shorter than 140 cm should ever
sit in the front passenger seat if the airbag
is activated.
Failure to follow the advice given above
can endanger life.
Alternative 2: Position of airbag label on passenger side door pillar. The label becomes visible
when the passenger door is opened.
WARNING
•
a child seat/booster cushion on the front
passenger seat provided there is no activated airbag on the front passenger side.
Booster cushions/child seats with steel
braces or some other design that could
rest on the seatbelt buckle's opening button must not be used, as they could cause
the seatbelt buckle to open accidentally.
•
one or more child seats/booster cushions
in the rear seat.
Do not allow the upper section of the child
seat to rest against the windscreen.
You may place:
Alternative 1: Position of airbag label on passenger side sun visor.
WARNING
Never use a rear-facing child seat on a
seat protected by an activated airbag. Failure to follow this advice can lead to death
or serious injury to the child.
Related information
•
•
General information on child safety (p. 44)
•
Child seat - ISOFIX (p. 50)
Child seats - upper mounting points
(p. 53)
49
02 Safety
02
Child seat - ISOFIX
ISOFIX - size classes
ISOFIX is a fixture system for car child seats
(p. 45) that is based on an international standard.
There is a size classification for child seats
using the ISOFIX (p. 50) fixture system in
order to assist users in choosing the correct
type of child seat (p. 51).
Size
class
Mounting points for the ISOFIX fixture system
are located at the lower section of the rear
seat backrest, in the outer seats.
The location of the mounting points is indicated by symbols in the backrest upholstery
(see preceding illustration).
Always follow the manufacturer's installation
instructions when connecting a child seat to
the ISOFIX mounting points.
Related information
•
•
•
50
ISOFIX - size classes (p. 50)
ISOFIX - types of child seat (p. 51)
General information on child safety (p. 44)
WARNING
Never place the child in the passenger
seat if the car is fitted with an activated airbag.
NOTE
Description
A
Full size, front-facing child
seat
B
Reduced size (alt. 1), frontfacing child seat
B1
Reduced size (alt.2), front-facing child seat
C
Full size, rear-facing child seat
D
Reduced size, rear-facing
child seat
E
Rear-facing infant seat
F
Transverse infant seat, lefthand
G
Transverse infant seat, righthand
If an ISOFIX child seat has no size classification, the car model must be included on
the vehicle list for the child seat.
NOTE
Volvo recommends that you contact an
authorised Volvo dealer for recommendations about which ISOFIX child seats Volvo
recommends.
Related information
•
ISOFIX - types of child seat (p. 51)
02 Safety
ISOFIX - types of child seat
Child seats are in different sizes – cars are in
different sizes. This means that not all child
Type of child seat
Infant seat transverse
Infant seat, rear-facing
Weight
max 10 kg
max 10 kg
seats are suitable for all seats in all car models.
Size class
Passenger seats for ISOFIXA installation of child seats
Front seat
Outer rear seat
F
X
X
G
X
X
E
X
OK
02
(IL)
Infant seat, rear-facing
max 13 kg
E
X
OK
(IL)
D
X
OK
(IL)
C
X
OK
(IL)
Child seat, rear-facing
9-18 kg
D
X
OK
(IL)
C
X
OK
(IL)
}}
51
02 Safety
||
Type of child seat
Child seat, front-facing
02
Weight
9-18 kg
Size class
B
Passenger seats for ISOFIXA installation of child seats
Front seat
Outer rear seat
X
OKB
(IUF)
B1
X
OKB
(IUF)
A
X
OKB
(IUF)
X: The ISOFIX position is not suitable for ISOFIX child seats in this weight class and/or size class.
IL: Suitable for specific ISOFIX child seats. These child seats may be intended for use in a special car model, limited or semi-universal categories.
IUF: Suitable for front-facing ISOFIX child seats that are universally approved in this weight class.
A
B
ISOFIX is a fixture system for car child seats that is based on an international standard.
Volvo recommends rear-facing child seats for this group.
Make sure you select the right size class
(p. 50) of child seat with ISOFIX fixture system.
Related information
•
52
Child seat - ISOFIX (p. 50)
02 Safety
Child seats - upper mounting points
NOTE
The car is equipped with upper mounting
points for certain front-facing child seats
(p. 45). These mounting points are located on
the rear of the seat.
Upper mounting points
In cars with a cargo cover over the luggage compartment, this must be removed
before child seats can be attached to the
securing points.
02
For detailed information on how the child seat
should be tensioned in the upper mounting
points, see the seat manufacturer's instructions.
WARNING
The child seat's straps must always be
drawn through the hole in the head
restraint leg before they are tensioned at
the attachment point.
Related information
The upper mounting points are primarily
intended for use with front-facing child seats.
Volvo recommends that small children should
sit in rear-facing child seats to as late an age
as possible.
•
•
•
General information on child safety (p. 44)
Child seats - location (p. 49)
Child seat - ISOFIX (p. 50)
NOTE
Fold the head restraints in order to facilitate fitting this type of child seat in cars
with folding head restraints on the outer
seats.
53
INSTRUMENTS AND CONTROLS
03 Instruments and controls
Instruments and controls, left-hand
drive car - overview
The overview shows where the car's displays
and controls are located.
03
}}
55
03 Instruments and controls
||
Overview, left-hand drive cars
03
56
03 Instruments and controls
Function
See
Function
See
Function
See
Menus and messages, direction
indicators, main/
dipped beam, trip
computer
(p. 105),
(p. 107),
(p. 91),
(p. 86) and
(p. 118).
Door handle
–
Control panel
(p. 83) and
(p. 173).
Seat adjustment*
(p. 79).
Manual gear changing in an automatic
gearbox*
(p. 270).
(p. 172),
(p. 177),
(p. 99) and
(p. 101).
Light switch,
opener for tailgate
Cruise control*
(p. 193) and
(p. 198).
Horn, airbags
(p. 82) and
(p. 30).
Combined instrument panel
(p. 61).
Menu navigation,
audio control,
phone control*
(p. 108) and
the Sensus
Infotainment
supplement.
START/STOP
ENGINE button
Hazard warning
flashers
(p. 90).
Control panel for
infotainment system and menu navigation
(p. 108) and
the Sensus
Infotainment
supplement.
Control panel for
climate control
(p. 127) or
(p. 128).
Gear selector
(p. 269),
(p. 270) or
(p. 274).
Parking brake
(p. 290).
(p. 266).
Wipers and washing
(p. 97).
Ignition switch
(p. 75).
(p. 82).
Screen for infotainment and display of
menus
(p. 108) and
the Sensus
Infotainment
supplement.
Steering wheel
adjustment
Bonnet opener
(p. 351).
Related information
•
•
•
Outside temperature gauge (p. 70)
Trip meter (p. 70)
03
Clock (p. 70)
* Option/accessory, for more information, see Introduction.
57
03 Instruments and controls
Instruments and controls, right-hand
drive car - overview
The overview shows where the car's displays
and controls are located.
03
58
03 Instruments and controls
Overview, right-hand drive cars
03
}}
59
03 Instruments and controls
||
03
60
Function
See
Function
See
Function
See
Wipers and washing
(p. 97).
Control panel
Light switch,
opener for tailgate
(p. 83) and
(p. 173).
Manual gear changing in an automatic
gearbox*
(p. 270).
(p. 172),
(p. 177),
(p. 99) and
(p. 101).
Seat adjustment*
(p. 79).
Menu navigation,
audio control,
phone control*
(p. 108) and
the Sensus
Infotainment
supplement.
Horn, airbags
(p. 82) and
(p. 30).
Combined instrument panel
Bonnet opener
(p. 351).
Hazard warning
flashers
(p. 90).
Control panel for
infotainment system and menu navigation
(p. 108) and
the Sensus
Infotainment
supplement.
(p. 61).
Control panel for
climate control
(p. 127) or
(p. 128).
Cruise control*
(p. 193) and
(p. 198).
Gear selector
START/STOP
ENGINE button
(p. 266).
(p. 269),
(p. 270) or
(p. 274).
Parking brake
(p. 290).
Ignition switch
(p. 75).
Screen for infotainment and display of
menus
(p. 108) and
the Sensus
Infotainment
supplement.
Menus and messages, direction
indicators, main/
dipped beam, trip
computer
(p. 105),
(p. 107),
(p. 91),
(p. 86) and
(p. 118).
Door handle
–
Steering wheel
adjustment
(p. 82).
* Option/accessory, for more information, see Introduction.
Related information
•
•
•
Outside temperature gauge (p. 70)
Trip meter (p. 70)
Clock (p. 70)
03 Instruments and controls
Combined instrument panel
The combined instrument panel's information
display shows information on some of the
car's functions, e.g. cruise control and trip
computer, as well as messages.
•
Analogue combined instrument panel overview (p. 61)
•
Digital combined instrument panel - overview (p. 62)
•
Combined instrument panel - meaning of
indicator symbols (p. 66)
•
Combined instrument cluster - meaning
of warning symbols (p. 68)
Analogue combined instrument panel
- overview
Gauges and indicators
The combined instrument panel's information
display shows information on some of the
car's functions, e.g. cruise control and trip
computer, as well as messages. The information is shown with symbols and text.
Information display
03
Fuel gauge. When the indicator lowers to
only one white marking1, the yellow indicator symbol for low level in the fuel tank
is illuminated. See also Trip computer supplementary information (p. 118) and
Filling up with fuel (p. 295).
Information display, analogue instrument panel.
There are further descriptions under the functions that use the display.
Eco meter The meter provides an indication of how economically the car is being
driven. The higher the reading on the
scale, the more economical it is.
Speedometer
Tachometer. The meter indicates engine
speed in thousands of revolutions per
minute (rpm).
Gear shift indicator2 / Gear position indicator3. See also Gear shift indicator*
1
2
3
When the display's message Distance to empty fuel tank: starts to show ----, the marking becomes red.
Manual gearbox.
Automatic gearbox.
}}
* Option/accessory, for more information, see Introduction.
61
03 Instruments and controls
||
(p. 270), Automatic gearbox - Geartronic*
(p. 270) or Automatic gearbox Powershift* (p. 274).
Indicator and warning symbols
If the engine does not start or if the functionality check is carried out in key position II
then all symbols go out within a few seconds
except the symbol for faults in the car's emissions system and the symbol for low oil pressure.
Related information
•
•
03
Combined instrument panel (p. 61)
Digital combined instrument panel overview
The combined instrument panel's information
display shows information on some of the
car's functions, e.g. cruise control and trip
computer, as well as messages. The information is shown with symbols and text.
Information display
Combined instrument panel - meaning of
indicator symbols (p. 66)
•
Combined instrument cluster - meaning
of warning symbols (p. 68)
•
Digital combined instrument panel - overview (p. 62)
Indicator and warning symbols, analogue instrument panel.
Indicator symbols
Indicator and warning symbols
Warning symbols4
Functionality check
All indicator and warning symbols, apart from
symbols in the centre of the information display, illuminate in key position II or when the
engine is started. When the engine has
started, all the symbols should go out except
the parking brake symbol, which only goes
out when the brake is disengaged.
4
62
Information display, digital instrument panel*.
There are further descriptions under the functions that use the display.
Gauges and indicators
Various themes can be selected for the digital
combined instrument panel. Possible themes
are "Elegance", "Eco" and "Performance".
A theme can only be selected when the
engine is running.
Certain engine variants do not have systems to warn of oil pressure loss. In cars with these variants the symbol for low oil pressure is not used. Warning for low oil level is via display text. For
more information, see Engine oil - general (p. 353).
* Option/accessory, for more information, see Introduction.
03 Instruments and controls
To select the theme, press the left-hand stalk
switch's OK button and select the Themes
menu option by turning the thumbwheel on
the lever. Press the OK button. Turn the
thumbwheel to select the theme and confirm
the selection by pressing the OK button.
(p. 270) or Automatic gearbox Powershift* (p. 274).
On certain model variants, the appearance of
the centre console's screen follows the theme
selected for the combined instrument panel.
The contrast mode and colour mode for the
instrument can also be set using the left-hand
stalk switch.
For more information on menu navigation,
see Menu navigation - combined instrument
panel (p. 105).
The choice of theme and setting of contrast
mode and colour mode can be stored for
each remote control key in the car key memory*, see Remote control key - personalisation* (p. 157).
03
Gauges and indicators, theme "Elegance".
Fuel gauge. When the indicator lowers to
only one white marking5, the yellow indicator symbol for low level in the fuel tank
is illuminated. See also Trip computer supplementary information (p. 118) and
Filling up with fuel (p. 295).
Temperature gauge for engine coolant
Speedometer
Tachometer. The meter indicates engine
speed in thousands of revolutions per
minute (rpm).
Gauges and indicators, theme "Eco".
Fuel gauge. When the indicator lowers to
only one white marking8, the yellow indicator symbol for low level in the fuel tank
is illuminated. See also Trip computer supplementary information (p. 118) and
Filling up with fuel (p. 295).
Eco guide. See also Eco guide & Power
guide* (p. 65).
Speedometer
Gear shift indicator6 / Gear position indicator7. See also Gear shift indicator*
(p. 270), Automatic gearbox - Geartronic*
5
6
7
8
When the display's message Distance to empty fuel tank: starts to show ----, the marking becomes red.
Manual gearbox.
Automatic gearbox.
When the display's message Distance to empty fuel tank: starts to show ----, the marking becomes red.
}}
* Option/accessory, for more information, see Introduction.
63
03 Instruments and controls
||
Tachometer. The meter indicates engine
speed in thousands of revolutions per
minute (rpm).
Gear shift indicator6 / Gear position indicator7. See also Gear shift indicator*
(p. 270), Automatic gearbox - Geartronic*
(p. 270) or Automatic gearbox Powershift* (p. 274).
03
Speedometer
Indicator and warning symbols
Tachometer. The meter indicates engine
speed in thousands of revolutions per
minute (rpm).
Power guide. See also Eco guide &
Power guide* (p. 65).
Gear shift indicator6 / Gear position indicator7. See also Gear shift indicator*
(p. 270), Automatic gearbox - Geartronic*
(p. 270) or Automatic gearbox Powershift* (p. 274).
Indicator and warning symbols, digital instrument
panel.
Indicator symbols
Indicator and warning symbols
Warning symbols10
Gauges and indicators, theme "Performance".
Fuel gauge. When the indicator lowers to
only one white marking9, the yellow indicator symbol for low level in the fuel tank
is illuminated. See also Trip computer supplementary information (p. 118) and
Filling up with fuel (p. 295).
Temperature gauge for engine coolant
6
7
9
10
64
Manual gearbox.
Automatic gearbox.
When the display's message Distance to empty fuel tank: starts to show ----, the marking becomes red.
Certain engine variants do not have systems to warn of oil pressure loss. In cars with these variants the symbol for low oil pressure is not used. Warning for low oil level is via display text. For
more information, see Engine oil - general (p. 353).
* Option/accessory, for more information, see Introduction.
03 Instruments and controls
Functionality check
Eco guide & Power guide*
Instantaneous value
All indicator and warning symbols, apart from
symbols in the centre of the information display, illuminate in key position II or when the
engine is started. When the engine has
started, all the symbols should go out except
the parking brake symbol, which only goes
out when the brake is disengaged.
Eco guide and Power guide are two combined instrument panel (p. 61) instruments
which help the driver to drive the car with
optimum driving economy.
The instantaneous value is shown here - the
higher the reading on the scale, the better.
If the engine does not start or if the functionality check is carried out in key position II
then all symbols go out within a few seconds
except the symbol for faults in the car's emissions system and the symbol for low oil pressure.
Related information
•
•
Combined instrument panel (p. 61)
The car also stores statistics of journeys
made, which can be viewed in the form of a
block diagram; see Trip computer - trip statistics* (p. 119).
Eco guide
This instrument provides an indication of how
economically the car is being driven.
To view this function, select the theme "Eco";
see Digital combined instrument panel - overview (p. 62).
Combined instrument panel - meaning of
indicator symbols (p. 66)
•
Combined instrument cluster - meaning
of warning symbols (p. 68)
•
Analogue combined instrument panel overview (p. 61)
The instantaneous value is calculated based
on speed, engine speed, engine power utilised plus use of the foot brake.
Optimum speed (50-80 km/h) and low engine
speeds are encouraged. The pointers fall during acceleration and braking.
03
Very low instantaneous values illuminate the
red zone on the meter (with a short delay),
which means poor driving economy and
hence should be avoided.
Average value
The average value slowly follows the instantaneous value and describes how the car has
been driven most recently. The higher the
pointers on the scale, the better the economy
achieved by the driver.
Power guide
This instrument shows the relationship
between how much power (Power) is being
taken from the engine and how much power
is available.
To view this function, select the theme
"Performance"; see Digital combined instrument panel - overview (p. 62).
Instantaneous value
Average value
}}
* Option/accessory, for more information, see Introduction.
65
03 Instruments and controls
||
Combined instrument panel meaning of indicator symbols
Symbol
Information, read display text
The indicator symbols alert the driver that a
function is activated, that the system is operating, or that an error or failure has occurred.
Main beam On
Indicator symbols
Symbol
03
Left-hand direction indicator
Specification
ABL fault
Right-hand direction indicator
Emissions system
Eco-function on, see ECO*
(p. 286)
ABS fault
Start/Stop, the engine autostopped; see Start/Stop* function and operation (p. 278)
Available engine power
Engine power utilised
Available engine power
The smaller, upper pointer shows the available engine power11. The higher the reading on
the scale, the more power is available in the
current gear.
Engine power utilised
The larger, lower pointer shows the engine
power utilised11. The higher the reading on
the scale, the more power is being taken from
the engine.
A large gap between the two pointers indicates a large power reserve.
11
66
Power is dependent on engine speed.
* Option/accessory, for more information, see Introduction.
Specification
Rear fog lamp on
Tyre pressure system , see
Tyre pressure monitoring*
(p. 324)
Stability system, see Electronic
stability control (ESC) - general
(p. 183)
Stability system, sport mode,
see Electronic stability control
(ESC) - operation (p. 184)
Engine preheater (diesel)
Low level in fuel tank
ABL fault
The symbol illuminates if a fault has arisen in
the ABL function (Active Bending Lights).
Emissions system
If the symbol illuminates after the engine has
been started then it may be due to a fault in
the car's emissions system. Drive to a workshop for checking. Volvo recommends that
you seek assistance from an authorised Volvo
workshop.
03 Instruments and controls
ABS fault
Engine preheater (diesel)
Eco function on
If this symbol illuminates then the system is
not working. The car's regular brake system
continues to work, but without the ABS function.
This symbol illuminates during engine preheating. Preheating mostly takes place due to
low temperature.
This symbol illuminates when the Eco function is activated.
Low level in fuel tank
1. Stop the car in a safe place and turn off
the engine.
When the symbol illuminates the level in the
fuel tank is low, refuel as soon as possible.
2. Restart the engine.
Information, read display text
3. If the symbol remains illuminated, drive to
a workshop to have the ABS system
checked. Volvo recommends that you
seek assistance from an authorised Volvo
workshop.
Rear fog lamp on
This symbol illuminates when the rear fog
lamp is switched on.
Stability system
A flashing symbol indicates that the stability
system is operating. If the symbol illuminates
with constant glow then there is a fault in the
system.
Stability system, sport mode
Sport mode allows for a more active driving
experience. The system then detects whether
the accelerator pedal, steering wheel movements and cornering are more active than in
normal driving and then allows controlled
skidding of the rear section up to a certain
level before it intervenes and stabilises the
car. The symbol illuminates when the sport
mode is activated.
When one of the car's systems does not
behave as intended, this information symbol
illuminates and a text appears on the information display. The message text is cleared with
the OK button, see Menu navigation - combined instrument panel (p. 105), or it disappears automatically after a time (time
depending on which function is indicated).
The information symbol can also illuminate in
conjunction with other symbols.
NOTE
Start/Stop
The symbol shines when the engine is autostopped.
Tyre pressure system
The symbol illuminates in the event of low
tyre pressure, or if a fault arises in the tyre
pressure system.
03
Related information
•
•
Combined instrument panel (p. 61)
Combined instrument cluster - meaning
of warning symbols (p. 68)
•
Analogue combined instrument panel overview (p. 61)
•
Digital combined instrument panel - overview (p. 62)
When a service message is shown, the
symbol and message are cleared using the
OK button, or disappear automatically
after a time.
Main beam On
The symbol illuminates when main beam is on
and with main beam flash.
Left/right-hand direction indicator
Both direction indicator symbols flash when
the hazard warning flashers are used.
67
03 Instruments and controls
Combined instrument cluster meaning of warning symbols
The warning symbols alert the driver that an
important function is activated, or that a serious error or a serious failure has occurred.
Warning symbols
Symbol
03
Specification
Low oil pressure
Fault in brake system
If this symbol illuminates during driving then
the engine's oil pressure is too low. Stop the
engine immediately and check the engine oil
level, top up if necessary. If the symbol illuminates and the oil level is normal, contact a
workshop. Volvo recommends that you seek
assistance from an authorised Volvo workshop.
If this symbol illuminates, the brake fluid level
may be too low. Stop the car in a safe place
and check the level in the brake fluid reservoir; see Brake and clutch fluid - level
(p. 358).
Low oil pressureA
Parking brake applied
Parking brake applied, digital
instrument panel
This symbol illuminates with a constant glow
when the parking brake is applied. The symbol is illuminated during application. For more
information, see Parking brake (p. 290).
Parking brake applied, analogue instrument panel
Airbags – SRS
Seatbelt reminder
Alternator not charging
Fault in brake system
Warning
Airbags – SRS
If this symbol remains illuminated or illuminates while driving, it means a fault has been
detected in the seatbelt buckle, SRS, SIPS, or
IC systems. Drive immediately to a workshop
to have the system checked. Volvo recommends that you seek assistance from an
authorised Volvo workshop.
Seatbelt reminder
This symbol flashes if someone in a front seat
has not put on their seatbelt or if someone in
a rear seat has taken off their seatbelt.
Alternator not charging
A
68
Certain engine variants do not have systems to warn of oil
pressure loss. In cars with these variants the symbol for
low oil pressure is not used. Warning for low oil level is via
display text. For more information, see Engine oil - general
(p. 353).
This symbol illuminates during driving if a
fault has occurred in the electrical system.
Visit a workshop. Volvo recommends that you
seek assistance from an authorised Volvo
workshop.
If the brake and ABS symbols illuminate at
the same time, there may be a fault in the
brake force distribution system.
1. Stop the car in a safe place and turn off
the engine.
2. Restart the engine.
•
If both symbols extinguish, continue
driving.
•
If the symbols remain illuminated,
check the level in the brake fluid reservoir; see Brake and clutch fluid - level
(p. 358). If the brake fluid level is normal but the symbols are still illuminated, the car can be driven, with great
care, to a workshop to have the brake
system checked. Volvo recommends
that you seek assistance from an
authorised Volvo workshop.
03 Instruments and controls
WARNING
If the brake fluid is below the MIN level in
the brake fluid reservoir, do not drive further before topping up the brake fluid.
The loss of brake fluid must be investigated by a workshop. Volvo recommends
that you contact an authorised Volvo
workshop.
WARNING
If the BRAKE and ABS symbols are lit at
the same time, there is a risk that the rear
end will skid during heavy braking.
Warning
The red warning symbol illuminates when a
fault has been indicated which could affect
the safety and/or driveability of the car. An
explanatory text is shown on the information
display at the same time. The symbol remains
visible until the fault has been rectified but the
text message can be cleared with the OK
button; see Menu navigation - combined
instrument panel (p. 105). The warning symbol can also illuminate in conjunction with
other symbols.
Action:
2. Read the information on the information
display. Implement the action in accordance with the message in the display.
Clear the message using the OK button.
Related information
Reminder – doors not closed
•
Analogue combined instrument panel overview (p. 61)
•
Digital combined instrument panel - overview (p. 62)
If one of the doors is not closed properly then
the information or warning symbol illuminates
together with an explanatory image in the
information display. Stop the car in a safe
place as soon as possible and close the door
that is open.
•
•
Combined instrument panel (p. 61)
Combined instrument panel - meaning of
indicator symbols (p. 66)
03
If the car is driven at a speed lower
than approx. 7 km/h then the information symbol illuminates.
If the car is driven at a speed higher
than approx. 7 km/h then the warning
symbol illuminates.
If the bonnet12 is not closed properly then the
warning symbol illuminates together with an
explanatory image in the information display.
Stop the car in a safe place as soon as possible and close the bonnet.
If the tailgate is not closed properly then the
information symbol illuminates together with
an explanatory image in the information display. Stop the car in a safe place as soon as
possible and close the tailgate.
1. Stop in a safe place. Do not drive the car
further.
12
Only cars with alarm*.
* Option/accessory, for more information, see Introduction.
69
03 Instruments and controls
Outside temperature gauge
Trip meter
Clock
The display for the outside temperature gauge
appears in the combined instrument panel.
The trip meter display appears in the combined instrument panel.
The clock display appears in the combined
instrument panel.
Trip meter, digital instrument.
Clock, digital instrument panel.
03
Display for outside temperature gauge,
digital instrument panel
Display for outside temperature gauge,
analogue instrument panel
When the temperature lies between +2 °C to
-5 °C a snowflake symbol illuminates in the
display. This warns of icy roads. If the car has
been stationary then the gauge may show a
reading that is too high.
Related information
•
Combined instrument panel (p. 61)
The two trip meters T1 and T2 are used for
measuring short distances. The distance is
shown in the display.
Turn the left stalk switch thumbwheel to show
the required meter.
A long press (until the change occurs) on the
left-hand stalk switch's RESET button resets
the trip meter shown. For more information,
see Trip computer - supplementary information (p. 118).
Related information
•
13
70
Display appearance may differ depending on instrument variant.
Display for showing the time14
Display for trip meter13
Combined instrument panel (p. 61)
Set the clock
The clock can be adjusted in the menu system MY CAR, see MY CAR (p. 108).
Related information
•
Combined instrument panel (p. 61)
03 Instruments and controls
Licenses - combined instrument panel
A license is an agreement for the right to
operate a certain activity or the right to use
someone else's entitlement according to the
terms and conditions in the agreement. The
following text is Volvo's agreement with the
manufacturer/developer.
Combined Instrument Panel Software
Open Source Software Notice
This product uses certain free / open source
and other software originating from third
parties, that is subject to the GNU Lesser
General Public License version 2 (LGPLv2),
The FreeType Project License ("FreeType
License") and other different and/or additional
copy right licenses, disclaimers and notices.
The links to access the exact terms of
LGPLv2, and the other open source software
licenses, disclaimers, acknowledgements and
notices are provided to you below. Please
refer to the exact terms of the relevant
License, regarding your rights under said
licenses. Volvo Car Corporation (VCC) offers
to provide the source code of said free/open
source software to you for a charge covering
the cost of performing such distribution, such
as the cost of media, shipping and handling,
upon written request. Please contact your
nearest Volvo Dealer.
14
The offer is valid for a period of at least three
(3) years from the date of the distribution of
this product by VCC / or for as long as VCC
offers spare parts or customer support.
MIT License: http: http://opensource.org/
licenses/mit-license.html
•
・ Lua
Portions of this product uses software
copyrighted © 2007 The FreeType Project
(www.freetype.org). All rights reserved.
Portions of this product uses software with
Copyright © 1994–2013 Lua.org, PUC-Rio
(http://www.lua.org/)
03
This product includes software under
following licenses:
LGPL v2.1: http://www.gnu.org/licenses/oldlicenses/lgpl-2.1.html
•
•
・ GNU FriBidi
・ DevIL
The FreeType Project License: http://
git.savannah.gnu.org/cgit/freetype/
freetype2.git/tree/docs/FTL.TXT
•
・ FreeType 2
The time is shown in the middle of the instrument panel when an analogue instrument panel is fitted.
71
03 Instruments and controls
Symbols in the display
There are a variety of different symbols in the
display in the car. The symbols are divided
into warning, indicator and information symbols. Shown below are the most common
symbols with their meanings and a reference
to where in the manual further information can
be found.
03
- Red warning symbol, illuminates when
a fault has been indicated which could affect
the safety and/or driveability of the car. An
explanatory text is shown on the information
display in the combined instrument panel at
the same time.
- When one of the car's systems does
not behave as intended, this information symbol illuminates, and a text appears on the
information display in the combined instrument panel. The yellow information symbol
can also illuminate in conjunction with other
symbols.
Warning symbols in the combined
instrument panel
Symbol
72
Symbol
Specification
See
Low oil pressure
(p. 68)
Parking brake
applied, digital
instrument panel
(p. 68),
(p. 290)
Specification
See
Parking brake
applied, analogue
instrument panel
(p. 68)
Airbags – SRS
(p. 29),
(p. 68)
Seatbelt reminder
(p. 25),
(p. 68)
Alternator not
charging
(p. 68)
Fault in brake
system
(p. 68),
(p. 288)
Warning, safety
mode
(p. 29),
(p. 40),
(p. 68)
Control symbols in the combined
instrument panel
Symbol
* Option/accessory, for more information, see Introduction.
Specification
See
ABL fault*
(p. 66),
(p. 89)
Emissions system
(p. 66)
ABS fault
(p. 66),
(p. 288)
Symbol
Specification
See
Rear fog lamp
on
(p. 66),
(p. 89)
Stability system,
ESC (Electronic
Stability Control), Trailer stability assist*
(p. 66),
(p. 185),
(p. 307)
Stability system,
sport mode
(p. 66),
(p. 185)
Engine preheater (diesel)
(p. 66)
Low level in fuel
tank
(p. 66),
(p. 139)
Information,
read display text
(p. 66)
Main beam On
(p. 66),
(p. 86)
Left-hand direction indicators
(p. 66)
Right-hand
direction indicators
(p. 66)
Start/Stop*,
engine autostopped
(p. 66),
(p. 278)
03 Instruments and controls
Symbol
Specification
See
ECO function*
on
Tyre pressure
system*
Specification
See
(p. 66),
(p. 286)
Adaptive cruise
control*
(p. 201)
(p. 66), Tyre
pressure
monitoring*
(p. 324)
Cruise control*
(p. 193)
Speed limiter
(p. 189)
Radar sensor*
(p. 211),
(p. 215),
(p. 231)
Start/Stop*
(p. 284)
Start/Stop*
(p. 284)
Start/Stop*
(p. 284)
Distance warning*
(Distance Alert),
City SafetyTM,
Collision warning
system*, Autobrake*
(p. 215),
(p. 222),
(p. 231)
Information symbols in the combined
instrument panel
Symbol
Specification
See
Main beam with
auto dimming AHB*
(p. 87)
Camera sensor*,
Laser sensor*
(p. 87),
(p. 222),
(p. 231),
(p. 234),
(p. 240)
Adaptive cruise
control*
(p. 211)
Adaptive cruise
control*
(p. 202),
(p. 211)
Adaptive cruise
control*, Distance
Warning* (Distance Alert)
(p. 211),
(p. 213)
Symbol
Symbol
Specification
See
Engine block
heater and passenger compartment heater*
(p. 139)
Engine block
heater and passenger compartment heater*
Service required
(p. 139)
Activated timer*
(p. 139)
Activated timer*
(p. 139)
ABL system*
(p. 89)
Low battery
(p. 139)
Park Assist Pilot PAP*
(p. 249)
Rain sensor*
(p. 97)
03
}}
* Option/accessory, for more information, see Introduction.
73
03 Instruments and controls
||
Symbol
03
Specification
See
Lane Keeping
Aid*
(p. 238)
Driver Alert System*, Lane Keeping Aid*
(p. 234),
(p. 240)
Driver Alert System*, Time for a
break
(p. 233)
Driver Alert System*, Time for a
break
(p. 234)
Information symbols in the roof console
display
Symbol
Specification
See
Seatbelt reminder
(p. 28)
Airbag, passenger
seat, activated
(p. 33)
Airbag, passenger
seat, deactivated
(p. 33)
Related information
Gear shift indicator
(p. 270)
Gear positions
(p. 270)
Registered speed
information*
(p. 187)
Measuring the oil
level
(p. 354)
•
Combined instrument panel - meaning of
indicator symbols (p. 66)
•
Combined instrument cluster - meaning
of warning symbols (p. 68)
•
Messages - handling (p. 107)
Volvo Sensus
Volvo Sensus is the heart of your personal
Volvo experience. It is Sensus that provides
information, entertainment and functions to
simplify your ownership.
When you are sitting in your car you want
control, and in today's interconnected world,
this includes information, communication and
entertainment when it is most suitable for
you. Sensus covers all our solutions that enable connection* to the outside world, at the
same time providing you with intuitive control
over all the car's capabilities.
Volvo Sensus combines and presents many
functions in several of the car's systems on
the centre console's display screen. With
Volvo Sensus the car can be personalised by
means of an intuitive user interface. Settings
can be made in Car settings, Audio and
media, Climate control, etc.
With the centre console buttons and controls
or the steering wheel's right-hand keypad*
74
* Option/accessory, for more information, see Introduction.
03 Instruments and controls
functions can be activated or deactivated and
many different settings can be made.
With a press on MY CAR all settings related
to the driving and control of the car are presented, such as City Safety, locks and alarm,
automatic fan speed, setting the clock, etc.
With a press on the respective function
*, NAV* and CAM*
RADIO, MEDIA, TEL*,
other sources, systems and functions can be
activated, e.g. AM, FM, CD, DVD*, TV*,
Bluetooth®*, navigation* and park assist camera*.
Key positions
of the buttons both vary, depending on the
equipment selected and the market.
Navigation* - NAV, see separate supplement (Sensus Navigation).
Audio and media - RADIO, MEDIA, TEL*,
see separate supplement (Sensus Infotainment).
The remote control key can be used to set the
vehicle's electrical system in different modes/
levels so that different functions are available;
see Key positions - functions at different levels (p. 76).
Function settings - MY CAR, see MY
CAR (p. 108).
03
Internet-connected car *, see separate supplement (Sensus Infotainment).
Climate control system (p. 121).
For more information about all functions/
systems, see the relevant section in the
owner's manual or its supplement.
Overview
Ignition switch with remote control key extracted/inserted.
NOTE
For cars with the Keyless* function the key
does not need to be inserted into the ignition switch but can be stored in e.g. a
pocket. For more information on Keyless
functions, see Keyless drive* (p. 166).
Control panel in centre console. The figure is
schematic - the number of functions and layout
}}
* Option/accessory, for more information, see Introduction.
75
03 Instruments and controls
||
Insert the key
1. Hold the end of the remote control key
with the detachable key blade and insert
the key in the ignition switch.
2. Then press the key in the lock up to its
end position.
IMPORTANT
03
Foreign objects in the ignition switch can
impair the function or destroy the lock.
Do not press in the remote control key
incorrectly turned - Hold the end with the
detachable key blade; see Detachable key
blade - detaching/attaching (p. 164).
Withdraw the key
Push the remote control key, allow it to eject,
then pull it out from the ignition switch.
Key positions - functions at different
levels
Level
Functions
In order to enable the use of a limited number
of functions with the engine switched off, the
car's electrical system can be set in 3 different levels (key positions) - 0, I and II - with the
remote control key. Throughout this owner's
manual these levels are described using the
denomination "key positions".
0
The following table shows the functions available in each key position/level.
I
Sun visor for glass roof, power
windows, 12 V socket in the passenger compartment, RTI, phone,
ventilation fan and windscreen
wipers can be used.
II
The headlamps come on.
Odometer, clock and temperature
gauge are illuminated.
Power seats can be adjusted.
The audio system can be used for
a limited time - see the Sensus
Infotainment supplement.
Warning/indicator lamps illuminate for 5 seconds.
Several other systems are activated. However, heating in seat
cushions and the rear window can
only be activated after the engine
has been started.
This key position consumes a
lot of current from the starter
battery and should therefore be
avoided!
76
03 Instruments and controls
Choosing key position/level
•
Key position 0 - Unlock the car - This
means that the car's electrical system is
at level 0.
•
Key position I - With the remote control
key fully inserted into the ignition switch15
- Briefly press START/STOP ENGINE.
Towing
Seats, front
For important information about the remote
control key during towing, see Towing
(p. 308).
The car's front seats have different setting
options for optimum seating comfort.
Related information
•
Key positions (p. 75)
NOTE
03
To reach level I or II without starting the
engine - do not depress the brake/clutch
pedal when these key positions are due to
be selected.
•
•
Key position II - With the remote control
key fully inserted into the ignition switch15
- Give a long16 press on START/STOP
ENGINE.
Back to key position 0 - To return to key
position 0 from position II and I - Briefly
press on START/STOP ENGINE.
Audio system
For information on audio system functions
with remote control key removed, see the
Sensus Infotainment supplement.
To adjust lumbar support*, turn the
wheel17.
Forward/backward: lift the handle to
adjust the distance to the steering wheel
and pedals. Check that the seat is locked
after adjusting position.
To raise/lower the front edge of seat
cushion*, pump up/down.
Adjust backrest rake, turn the wheel.
Starting and stopping the engine
Raise/lower the seat*, pump up/down.
For information about starting/switching off
the engine, see Starting the engine (p. 266).
Control panel for power seat*, see Seats,
front - electrically operated (p. 79).
15
16
17
Not necessary for cars with the Keyless* function.
Approx. 2 seconds.
Also applies to electrically operated seat.
}}
* Option/accessory, for more information, see Introduction.
77
03 Instruments and controls
||
WARNING
Lowering the passenger seat backrest*
WARNING
Adjust the position of the driver's seat
before setting off, never while driving.
Make sure that the seat is in locked position in order to avoid personal injury in the
event of sudden braking or an accident.
03
Grasp the backrest and make sure that it
is properly locked after being folded up in
order to avoid personal injury in the event
of sudden braking or an accident.
Related information
Adjusting the front seat head restraint
The passenger seat backrest can be folded
forward to make room for long loads.
Move the seat as far back/down as possible.
Adjust the backrest to an upright position.
Lift the catches on the rear of the backrest and fold it forward.
The height of the head restraint can be adjusted.
Adjust the head restraint based on the person's height so that the whole of the back of
the head is covered if possible.
To adjust the height, the button (see illustration) must be pressed while the restraint is
moved up or down.
The head restraint can be adjusted in three
different positions.
78
4. Push the seat forward so that the head
restraint "locks" in under the glovebox.
Raising takes place in reverse order.
WARNING
Do not use the seat behind the passenger
seat, or the rear centre seat, when the
passenger seat's backrest is lowered.
* Option/accessory, for more information, see Introduction.
•
Seats, front - electrically operated
(p. 79)
•
Seats, rear (p. 80)
03 Instruments and controls
Seats, front - electrically operated
The car's front seats have different setting
options for optimum seating comfort. The
power seat can be moved forward/backward
and up/down. The front edge of the seat
cushion can be raised/lowered. The backrest
angle can be changed.
Electrically operated seat*
Store setting
wait a short time before adjusting the seat
again.
Memory button
Only one movement (forward/back/up/down)
can be made at a time.
Memory button
Memory button
Preparations
The seat can be adjusted for a certain time
after unlocking the door with the remote control key without the key in the ignition switch.
Seat adjustment is normally made in key
position I and can always be made when the
engine is running.
Seat with memory function*
Button for storing settings
1. Adjust the seat and the door mirrors.
2. Press and hold button M while pressing
button 1, 2 or 3 simultaneously. Hold the
buttons depressed until the acoustic signal is heard and the text is shown the
combined instrument panel.
03
The seat must be adjusted again before a
new memory can be set.
Using a stored setting
Press one of the memory buttons 1-3 until the
seat and the door mirrors stop. If the button
is released, the movement of the seat and
door mirrors will be interrupted.
Front edge of seat cushion up/down
Key memory* in remote control key
Raise/lower seat
Seat, forward/backward
Backrest rake
The power seats have overload protection
which is tripped if a seat is blocked by an
object. If this should happen, set the car's
electrical system in key position I or 0 and
18
The memory function stores settings for the
seat and the door mirrors.
All remote control keys can be used by different drivers to store the settings for the driver's seat and door mirrors18, see Remote
control key - personalisation* (p. 157).
Only if the car is equipped with power seat with memory and retractable power door mirrors.
}}
* Option/accessory, for more information, see Introduction.
79
03 Instruments and controls
||
Emergency stop
Seats, rear
If the seat accidentally begins to move, press
one of the setting buttons for the seat or
memory buttons in order to stop the seat.
The rear seat backrest and the outer seat
head restraints can be folded. The centre seat
head restraint can be adjusted to suit the
height of the passenger.
WARNING
Risk of crushing! Make sure that children
do not play with the controls. Check that
there are no objects in front of, behind or
under the seat during adjustment. Ensure
that none of the rear seat passengers is in
danger of becoming trapped.
03
Manual lowering of the outer head
restraints, rear seat
Head restraint, centre seat, rear
Heated seats
For heated seats, see Heated front seats*
(p. 129) and Heated rear seat* (p. 129).
Pull the locking handle closest to the head
restraint to fold the head restraint forward.
Related information
The head restraint is moved back manually.
•
•
Seats, front (p. 77)
Seats, rear (p. 80)
Adjust the head restraint according to passenger height so that the whole of the back of
the head is covered if possible. Slide it up as
required.
To lower the head restraint again, the button
(see illustration) must be pressed while the
restraint is carefully moved down.
The head restraint can be adjusted in five different positions.
NOTE
Do not sit in the centre seat with the head
restraint in fully lowered position.
80
* Option/accessory, for more information, see Introduction.
WARNING
The head restraint must be in locked position after being folded up.
Lowering the rear seat backrest
IMPORTANT
When the backrest is to be folded, the rear
seat cup holder must not be open and
there must be no objects in the rear seat.
Nor may the seat belts be connected. Otherwise there is a risk of damage to the rear
seat upholstery.
03 Instruments and controls
NOTE
NOTE
The front seats may need to be pushed
forwards, and/or the backrests adjusted
upwards, in order that the rear backrests
can be fully folded forward.
•
•
When the backrest has been raised, the
red indicator should no longer be showing.
If it is still showing then the backrest is not
locked in place.
Both sections can be folded separately.
If the entire backrest is to be folded then
the different sections should be folded
separately.
WARNING
If the right-hand section is being lowered
- release and adjust head restraint for the
centre seat, see the earlier section "Head
restraint, centre seat, rear".
The outer head restraints are lowered
automatically when the backrests are
lowered. Pull up the backrest's locking
handle
while folding the backrest forward at the same time. A red indicator on
shows that the backthe lock catch
rest is no longer locked in place.
Check that the backrests and head
restraints in the rear seat are locked properly after being folded up.
03
Related information
•
•
Seats, front (p. 77)
Seats, front - electrically operated (p. 79)
NOTE
When the backrests have been lowered
the head restraints must be moved forward slightly so as not to make contact
with the seat cushion.
Raising takes place in reverse order.
81
03 Instruments and controls
Steering wheel
The steering wheel can be adjusted in different positions and has controls for horn and
cruise control, as well as menu, audio and
phone control.
Adjusting
3. Pull the lever back to fix the steering
wheel in place. If the lever is stiff, press
the steering wheel lightly at the same time
as you push the lever back.
WARNING
Adjust the steering wheel and fix it before
driving away.
Paddle for manual gear changing in an
automatic gearbox, see Automatic gearbox - Geartronic* (p. 270)
Audio and phone control, see supplement, Sensus Infotainment
Horn
03
With speed related power steering* the level
of steering force can be adjusted, see Speed
related power steering (p. 259).
Keypads* and paddles*
Adjusting the steering wheel.
Horn.
Lever - releasing the steering wheel
Press the centre of the steering wheel to signal.
Possible steering wheel positions
The steering wheel can be adjusted for both
height and depth:
1. Push the lever forwards to release the
steering wheel.
Keypads and paddles in the steering wheel.
2. Adjust the steering wheel to the position
that suits you.
82
* Option/accessory, for more information, see Introduction.
Cruise control* (p. 193)
Adaptive cruise control (ACC)* (p. 198)
03 Instruments and controls
Light switches
The headlamp control activates and adjusts
the external lighting. It is also used to adjust
display and instrument lighting and mood
lighting (p. 92).
Overview, light switches
Knob positions
Position
Position
Specification
Daytime running lightsA when
the car's electrical system is in
key position II or the engine is
running.
Main beam flash can be used.
Daytime running lights, side
marker lamps rear and position/
parking lamps when the car's
electrical system is in key position II or the engine is running.
Side marker lamps rear and
position/parking lamps when
the car is parked.
Overview, light switches.
Thumbwheel for adjusting display and
instrument lighting and ambient lighting*
Button for rear fog lamp
Knob for daytime running lights and parking lamps
Thumbwheel19 for headlamp levelling
Main beam flash can be used.
Specification
Daytime running lights, side
marker lamps rear and position/
parking lamps in daylight when
the car's electrical system is in
key position II or the engine is
running.
03
Dipped beam, side marker
lamps rear and position/parking
lamps in weak daylight or darkness or when the rear fog lamp
is activated. On cars with active
Xenon headlamps* (p. 89) the
daytime running light lamps are
switched on with reduced
brightness.
The tunnel detection (p. 86)*
function is activated.
The active high beam (p. 87)*
function can be used.
Main beam can be activated
when dipped beam is switched
on.
Main beam flash can be used.
Dipped beam, side marker
lamps rear and position/parking
lamps.
19
Not available for cars equipped with active Xenon headlamps*.
}}
* Option/accessory, for more information, see Introduction.
83
03 Instruments and controls
||
Position
Specification
1. Leave the engine running, or have the
car's electrical system in key position I.
Main beam can be activated.
2. Roll the thumbwheel up/down to raise/
lower beam alignment.
Main beam flash can be used.
On cars with active Xenon
headlamps the daytime running
light lamps are switched on
with reduced brightness.
03
A
Fitted in or under the front bumper.
Volvo recommends that
mode is used
when the car is being driven, as long as traffic
situations or weather conditions are unfavourable for the Active high beam* function.
Instrument lighting
Different display and instrument lighting is
switched on depending on key position; see
Key positions - functions at different levels
(p. 76).
Thumbwheel positions for different load cases.
Only driver
Driver and passenger in the front passenger seat
The display lighting is automatically subdued
in darkness - the sensitivity is set with the
thumbwheel.
The intensity of the instrument lighting is
adjusted with the thumbwheel.
Headlamp levelling
The load in the car changes the vertical alignment of the headlamp beam, which could
dazzle oncoming motorists. Avoid this by
adjusting the height of the beam. Lower the
beam if the car is heavily laden.
84
Occupants in all seats
Occupants in all seats and maximum load
in the cargo area
Driver and maximum load in the cargo
area
Cars with active Xenon headlamps* have
automatic headlamp levelling and are therefore not equipped with the thumbwheel.
* Option/accessory, for more information, see Introduction.
Related information
•
•
•
Position/parking lamps (p. 85)
Daytime running lights (p. 85)
Main/dipped beam (p. 86)
03 Instruments and controls
Position/parking lamps
Position/parking lamps are switched on with
the headlamp control knob.
Related information
•
•
Light switches (p. 83)
Lamp replacement - location of front
lamps (p. 360)
Daytime running lights
With the knob for headlamp control in
position, and the car's electrical system in key
position II or the engine running, the daytime
running lights are activated automatically in
daylight.
Daytime running lights during the day.
DRL
03
Knob for headlamp control in the position for
position/parking lamps.
(numTurn the knob to the position for
ber plate lighting is switched on at the same
time).
If the car's electrical system is in key position
II or the engine is running then the daytime
running lights also switch on.
When it is dark outside and the tailgate is
opened the rear position/parking lamps illuminate to alert traffic behind. This takes place
irrespective of what position the knob is in or
what key position the car's electrical system
is in.
Knob for headlamp control in AUTO position.
With the knob for headlamp control in
position the daytime running lights (Daytime
Running Lights - DRL) are activated automatically when the car is driven in daylight. A light
sensor on the top of the instrument panel
changes from daytime running lights to
dipped beam at twilight or when daylight
becomes too weak. Switching to dipped
beam also takes place when the rear fog
lamps are activated.
}}
85
03 Instruments and controls
||
On cars with halogen headlamps the daytime
running light lamps are switched off when
main or dipped beam is activated.
On cars with active Xenon headlamps
(p. 89) the daytime running light lamps are
switched on with reduced brightness when
main or dipped beam is activated.
WARNING
03
This system help to save energy - it cannot
determine in all situations when daylight is
too weak or sufficiently strong, e.g. in mist
and rain.
The driver is always responsible for ensuring that the car is driven with the correct
beam pattern for the traffic situation and in
accordance with applicable traffic regulations.
Related information
•
Lamp replacement - location of front
lamps (p. 360)
Tunnel detection*
Main/dipped beam
Tunnel detection changes the lighting from
daytime running lights to dipped beam when
the car is driven into a tunnel. Approx. 20 seconds after the car has left the tunnel, the lighting returns to daytime running lights.
The tunnel detection function is available in
cars with rain sensor*. The sensor detects the
entrance to a tunnel and resets the lighting
from daytime running lights to dipped beam.
Approx. 20 seconds after the car has left the
tunnel, the lighting returns to daytime running
lights. If the car is driven into another tunnel
within this time period then dipped beam is
kept switched on. This prevents frequent
changes to the car's beam pattern.
Note that the headlamp control's knob must
position for tunnel detection
remain in
to work.
Related information
•
•
Main/dipped beam (p. 86)
Light switches (p. 83)
Stalk switch and knob for headlamp control.
Position for main beam flash
Position for main beam
Dipped beam
With the knob in
position, dipped beam
is activated automatically at dusk or when
daylight becomes too weak. Dipped beam is
also activated automatically when the rear fog
lamp is activated.
With the knob in
position, dipped beam
is always switched on when the engine is running or when key position II is active.
Main beam flash
Move the stalk switch gently towards the
steering wheel to the position for main beam
flash. Main beam comes on until the stalk
switch is released.
86
* Option/accessory, for more information, see Introduction.
03 Instruments and controls
Main beam
Active high beam*
Main beam can be activated when the knob
20 or
. Activate/deacis in position
tivate main beam by moving the stalk switch
towards the steering wheel to the end position and then releasing. Alternatively, the
main beam can be deactivated by a light
press of the stalk switch toward the steering
wheel.
The Active High Beam function detects the
headlamp beams of oncoming traffic or the
rear lights of vehicles in front, and switches
the lighting from main beam to dipped beam.
The lighting returns to main beam when the
incoming light has stopped.
When main beam has been activated the
symbol illuminates in the combined
instrument panel.
Related information
•
•
•
Active Xenon headlamps* (p. 89)
Active high beam* (p. 87)
Lamp replacement - location of front
lamps (p. 360)
•
•
Light switches (p. 83)
•
Tunnel detection* (p. 86)
Headlamps - adjusting headlamp pattern
(p. 94)
Active high beam - AHB
Active high beam (Active High Beam - AHB) is
a function which uses a camera sensor at the
top edge of the windscreen to detect the
headlamp beams of oncoming traffic or the
rear lights of vehicles in front, and then
switches from main beam to dipped beam.
The function can also take streetlights into
account.
The lighting returns to main beam about a
second after the camera sensor no longer
detects the headlamp beams from oncoming
traffic or the rear lights from vehicles in front.
Activating/deactivating
AHB can be activated when the headlamp
control's knob is in position
(provided
that the function has not been deactivated in
the menu system MY CAR, see MY CAR
(p. 108)).
03
Stalk switch and knob for headlamp control in
AUTO position.
The function can start while driving in the
dark when the car's speed is 20 km/h or
higher.
Activate/deactivate AHB by moving the lefthand stalk switch towards the steering wheel
to the end position and then releasing. Deactivation when main beam is on means that the
lights are reset directly to dipped beam.
Car with analogue combined instrument
panel
When AHB is activated the
symbol illuminates in the instrument's information display.
When main beam has been switched on the
symbol also illuminates in the combined instrument panel.
20
When dipped beam is activated.
}}
* Option/accessory, for more information, see Introduction.
87
03 Instruments and controls
||
Car with digital combined instrument panel
symbol
When AHB is activated the
turns white in the instrument's information
display.
When main beam is activated, the symbol
shines blue.
AHB may be temporarily unavailable e.g. in
situations with dense fog or heavy rain. When
AHB becomes available again, or the windscreen sensors are no longer blocked, the
symbol illumessage goes out and the
minates.
WARNING
Manual operation
03
NOTE
Keep the windscreen surface in front of the
camera sensor free from ice, snow, mist
and dirt.
Do not stick or attach anything to the
windscreen in front of the camera sensor
as this may reduce effectiveness or cause
one or more of the systems dependent on
the camera to stop working.
AHB is an aid for using the optimum beam
pattern when conditions are favourable.
The driver always bears responsibility for
manually switching between main and
dipped beam when traffic situations or
weather conditions so require.
If the message Active main beam
Temporary unavailable Switch manually is
shown in the combined instrument panel's
information display then you have to switch
manually between main and dipped beam.
However, the knob for headlamp control can
still remain in position
. The same
applies if the message Windscreen sensors
symbol
blocked See manual and the
are shown. The
symbol goes out when
these messages are shown.
88
IMPORTANT
Examples of when manual switching
between main and dipped beam may be
required:
* Option/accessory, for more information, see Introduction.
•
•
•
•
•
In heavy rain or dense fog
•
When the traffic ahead has weak lighting
•
If there are pedestrians on or beside
the road
•
If there are highly reflective objects
such as signs in the vicinity of the road
•
When the lighting from oncoming traffic is obscured by e.g. a crash barrier
•
When there is traffic on connecting
roads
•
•
On the brow of a hill or in a hollow
In freezing rain
In snow flurries or slush
In moonlight
When driving in poorly lit built-up
areas
In sharp bends.
For more information on the limitations of the
camera sensor, see Collision warning system*
- camera sensor limitations (p. 230).
Related information
•
•
Main/dipped beam (p. 86)
Light switches (p. 83)
03 Instruments and controls
Active Xenon headlamps*
Active Xenon headlamps are designed to provide maximum illumination in bends and junctions and so provide increased safety.
Active Xenon headlamps ABL
Headlamp pattern with function deactivated (left)
and activated (right) respectively.
If the car is equipped with active Xenon headlamps (Active Bending Lights – ABL) then the
light from the headlamps follows the steering
wheel movement in order to provide maximum lighting in bends and junctions and so
provide increased safety.
The function is activated automatically when
the car is started (provided that it has not
been deactivated in the menu system
MY CAR, see MY CAR (p. 108)). In the event
symbol illuof a fault in the function the
21
minates in the combined instrument panel at
the same time as the information display
shows an explanatory text and a further illuminated symbol.
Symbol
Message
Specification
Headlamp
system
malfunction Service
required
The system is
disengaged. Visit
a workshop if
the message
remains. Volvo
recommends
that you contact
an authorised
Volvo workshop.
The function is only active in twilight or darkness and only when the car is moving.
The function21 can be deactivated/activated
in the menu system MY CAR, see MY CAR
(p. 108).
Related information
•
•
•
•
Main/dipped beam (p. 86)
Active high beam* (p. 87)
Light switches (p. 83)
Headlamps - adjusting headlamp pattern
(p. 94)
Rear fog lamp
When visibility is reduced by fog the rear fog
lamp can be used so that other road users
shall notice vehicles in front at an early stage.
03
Button for rear fog lamp.
The rear fog lamp can only be switched on
when key position II is active or the engine is
running and the headlamp control's knob is in
or
.
position
Press the button for On/Off. The rear fog
lamp indicator symbol
in the combined
instrument panel and the lamp in the button
illuminate when the rear fog lamp is switched
on.
The rear fog lamp is switched off automatically when the engine is switched off or when
Activated on delivery from the factory.
}}
* Option/accessory, for more information, see Introduction.
89
03 Instruments and controls
||
the headlamp control's knob is turned to
or
.
position
NOTE
Regulations on the use of rear fog lamps
vary from country to country.
03
Related information
•
•
Light switches (p. 83)
Lamp replacement - location of rear
lamps (p. 364)
Brake lights
Hazard warning flashers
The brake light automatically comes on during
braking.
The hazard warning flashers warn other road
users by means of all of the car's direction
indicator lamps flashing simultaneously when
this function is activated.
The brake light is switched on when the brake
pedal is depressed. In addition, it is switched
on when one of driving support systems
Adaptive cruise control (p. 198), City Safety
(p. 216) or Collision warning system (p. 223)
brakes the car.
When the hazard warning flashers are activated, both direction indicator symbols flash
in the combined instrument panel.
For information on emergency brake lights
and automatic hazard warning flashers, see
Foot brake - emergency brake lights and
automatic hazard warning flashers (p. 289).
Related information
•
Lamp replacement - location of rear
lamps (p. 364)
Button for hazard warning flashers.
Press the button to activate the hazard warning flashers. Both direction indicator symbols
in the combined instrument panel flash when
the hazard warning flashers are used.
The hazard warning flashers are activated
automatically when the car has been braked
so suddenly that the emergency brake lights
have been activated at a speed below
10 km/h. The hazard warning flashers remain
on when the car has stopped and are deactivated automatically when the car is driven off
90
03 Instruments and controls
again or the button is depressed. For more
information on emergency brake lights and
automatic hazard warning flashers, see Foot
brake - emergency brake lights and automatic hazard warning flashers (p. 289).
Related information
•
Direction indicators
The car's direction indicators are operated
with the left-hand stalk switch. The direction
indicator lamps flash three times or continuously, depending on how far up or down the
stalk switch is moved.
Direction indicators (p. 91)
The stalk switch remains in its position and is
moved back manually, or automatically by the
steering wheel movement.
Direction indicator symbols
For direction indicator symbols, see Combined instrument panel - meaning of indicator
symbols (p. 66).
Related information
•
•
•
Hazard warning flashers (p. 90)
03
Lamp replacement - location of rear
lamps (p. 364)
Lamp replacement - location of front
lamps (p. 360)
Direction indicators.
Short flash sequence
Move the stalk switch up or down to the
first position and release. The direction
indicator lamps flash three times. The
function can be activated/deactivated in
the menu system MY CAR, see MY
CAR (p. 108).
Continuous flash sequence
Move the stalk switch up or down to the
outer position.
91
03 Instruments and controls
Interior lighting
Front reading lamps*
The passenger compartment lighting is activated/deactivated with the buttons in the controls above the front seats and the rear seat.
The reading lamps are switched on or off by
briefly pressing the relevant button in the roof
console.
Brightness is adjusted by holding the button
pressed in.
Rear reading lamps*
03
Lighting in the front door storage
compartments*
Lighting in the front door storage compartments comes on when the engine starts.
Glovebox lighting
Glovebox lighting is switched on and off
respectively when the lid is opened or closed.
Vanity mirror lighting
The lighting for the vanity mirror (p. 147) is
switched on and off respectively when the
cover is opened or closed.
To replace the lamp, see Lamp replacement vanity mirror lighting (p. 365).
Lighting in the cargo area
The lighting in the cargo area is switched on
and off respectively when the tailgate is
opened or closed.
Controls in roof console for the front reading
lamps and passenger compartment lighting.
Reading lamp, left-hand side
Passenger compartment lighting (floor
lamps* and ceiling lamps) - On/Off
Auto function for passenger compartment
lighting
Reading lamp, right-hand side
All lighting in the passenger compartment can
be switched on and off manually within
30 minutes from when:
92
•
the engine has been switched off and the
car's electrical system is in key position 0
•
the car has been unlocked but the engine
has not been started.
Rear reading lamps.
The lamps are switched on or off by briefly
pressing the relevant button.
Brightness is adjusted by holding the button
pressed in.
Floor lighting as ambient light*
To make the interior brighter while driving the
floor lighting can be activated at dimmed
level.
Floor lamp intensity can be changed in the
menu system MY CAR, see MY CAR (p. 108).
* Option/accessory, for more information, see Introduction.
Auto function for passenger
compartment lighting
The auto function is activated when the lamp
in the AUTO button is lit.
The passenger compartment lighting is then
switched on and off as indicated below.
The passenger compartment lighting is
switched on and remains on for 30 seconds
if:
•
the car is unlocked with the remote control key or key blade, see Remote control
03 Instruments and controls
key - functions (p. 160) or Detachable
key blade - unlocking doors (p. 164)
•
the engine has been switched off and the
car's electrical system is in key position
0.
Passenger compartment lighting is switched
off when:
•
•
the engine is started
the car is locked.
The passenger compartment lighting is
switched on and off respectively when a side
door is opened or closed.
It remains switched on for two minutes if one
of the doors is open.
If any lighting is switched on manually and
the car is locked then it will be switched off
automatically after two minutes.
Mood lights*
When the normal passenger compartment
lighting is switched off and the engine is running, an LED illuminates in the front and rear
roof console respectively in order to provide a
low light and enhance the ambience while
driving. The light also makes it easier during
dark periods of the day to see objects in storage compartments, etc. This lighting switches
off when the engine is switched off. The
intensity and colour of the light can be
changed in the menu system MY CAR, see
MY CAR (p. 108).
Home safe light duration
Approach light duration
Home safe lighting consists of dipped beam,
parking lamps, lamps in the door mirrors,
number plate lighting, interior roof lighting
and floor lighting.
Approach lighting consists of parking lamps,
lamps in the door mirrors, number plate lighting, interior roof lighting and floor lighting.
Some of the exterior lighting can be kept
switched on to work as home safe lighting
after the car has been locked.
1. Remove the remote control key from the
ignition switch.
2. Move the left-hand stalk switch toward
the steering wheel to the end position and
release it. The function can be activated
in the same way as with main beam flash;
see Main/dipped beam (p. 86).
3. Get out of the car and lock the door.
Approach lighting is switched on with the
remote control key, see Remote control key functions (p. 160), and is used to switch on
the car's lighting at a distance.
When the function is activated with the
remote control, the parking lamps, door mirror lamps, number plate lighting, interior roof
lighting and floor lighting are switched on.
03
The length of time for which the approach
lighting should be kept on can be set in the
menu system MY CAR, see MY CAR (p. 108).
Related information
When the function is activated, dipped beam,
parking lamps, door mirror lamps, number
plate lighting, interior roof lighting and floor
lighting are switched on.
•
Home safe light duration (p. 93)
The length of time for which the home safe
lighting should be kept on can be set in the
menu system MY CAR, see MY CAR (p. 108).
Related information
•
Approach light duration (p. 93)
* Option/accessory, for more information, see Introduction.
93
03 Instruments and controls
Headlamps - adjusting headlamp
pattern
Active Xenon headlamps*
The light pattern does not need to be
adjusted. The headlamp pattern is designed
in such a way that oncoming traffic is not
dazzled.
The headlamp pattern must be adjusted to
avoid dazzling oncoming motorists and can
be set for right or left-hand traffic.
Halogen headlamps
The headlamp pattern for halogen headlamps
is readjusted by masking the headlamp lens.
The headlamp pattern may not be as good.
03
Masking the headlamps
G021151
1. Copy the A and B templates for left-hand
drive cars or the C and D templates for
right-hand drive cars, see the later section "Templates for halogen headlamps":
Headlamp pattern, left-hand traffic.
•
A = LHD Right (left-hand drive, right
lens)
•
•
B = LHD Left (left-hand drive, left lens)
•
D = RHD Left (right-hand drive, left
lens)
C = RHD Right (right-hand drive, right
lens)
G021152
2. Transfer the template to a self-adhesive
waterproof material and cut it out.
3. Start from the design lines on the headlamp lenses; see the lines in the following
figure. Position the self-adhesive templates at the design lines with the help of
the illustration.
Headlamp pattern, right-hand traffic.
94
* Option/accessory, for more information, see Introduction.
03 Instruments and controls
03
Upper row: left-hand drive cars, templates A and B. Lower row: right-hand drive cars, templates C and D.
}}
95
03 Instruments and controls
||
Templates for halogen headlamps
03
96
03 Instruments and controls
Wipers and washing
Wipers and washers clean the windscreen
and rear window. The headlamps are cleaned
with high-pressure washing.
Windscreen wipers22
Intermittent wiping
Set the number of sweeps per time
unit with the thumbwheel when
intermittent wiping is selected.
Continuous wiping
The wipers sweep at normal speed.
IMPORTANT
Before activating the wipers during winter
ensure that the wiper blades are not frozen
in, and that any snow or ice on the windscreen is scraped away.
Rain sensor, on/off
Thumbwheel sensitivity/frequency
Windscreen wipers off
Move the stalk switch to position 0
to switch off the windscreen wipers.
Single sweep
Raise the stalk switch and release to
make one sweep.
When the rain sensor is activated a lamp in
the button is illuminated and the rain sensor
symbol
is shown in the combined
instrument panel.
Activating and setting the sensitivity
The wipers sweep at high speed.
Windscreen wipers and windscreen washers.
detects on the windscreen. The sensitivity of
the rain sensor can be adjusted using the
thumbwheel.
IMPORTANT
Use plenty of washer fluid when the wipers
are cleaning the windscreen. The windscreen must be wet when the windscreen
wipers are operating.
Service position wiper blade
For cleaning the windscreen/wiper blades
and replacement of wiper blades, see Wiper
blades (p. 366) and Car washing (p. 385).
Rain sensor*
When activating the rain sensor, the car must
be running or the remote control key in position I or II while the windscreen wiper stalk
switch must be in position 0 or in the position
for a single sweep.
03
Activate the rain sensor by pressing the but. The windscreen wipers make one
ton
sweep.
Press the stalk switch up for the wipers to
make an extra sweep.
Turn the thumbwheel upward for higher sensitivity and downward for lower sensitivity.
(An extra sweep is made when the thumbwheel is turned upward.)
Deactivate
Deactivate the rain sensor by pressing the
or move the stalk switch down
button
to another wiper program.
The rain sensor automatically starts the windscreen wipers based on how much water it
22
For replacing the wiper blades and service position wiper blades, see Wiper blades (p. 366). For filling washer fluid, see Washer fluid - filling (p. 369).
* Option/accessory, for more information, see Introduction.
}}
97
03 Instruments and controls
||
The rain sensor is automatically deactivated
when the remote control key is removed from
the ignition switch or five minutes after the
engine has been switched off.
IMPORTANT
03
The windscreen wipers could start and be
damaged in an automatic car wash.
Switch off the rain sensor while the car is
in motion or when the remote control key
is in position I or II. The symbol in the
combined instrument panel and the light in
the button go out.
Washing the headlamps and windows
Washing the windscreen
The windscreen wipers will make several
more sweeps and the headlamps are washed
once the stalk switch has been released.
High-pressure headlamp washing*
High-pressure headlamp washing consumes
a large quantity of washer fluid. To save fluid,
the headlamps are washed automatically at
every fifth windscreen wash cycle.
Reduced washing
Rear window wiper – intermittent wiping
If only approx. 1 litre of washer fluid remains
in the reservoir and the message that you
should fill the washer fluid is shown in the
combined instrument panel, then the supply
of washer fluid to the headlamps is switched
off. This is in order to prioritise cleaning the
windscreen and the visibility through it.
Rear window wiper – continuous speed
Washing function.
98
Wiping and washing the rear window
Move the stalk switch toward the steering
wheel to start the windscreen and headlamp
washers.
* Option/accessory, for more information, see Introduction.
Press the stalk switch forward (see the arrow
in the illustration above) to initiate rear window washing and wiping.
NOTE
The rear window wiper is equipped with
overheating protection which means that
the motor is switched off if it overheats.
The rear window wiper works again after a
cooling period (30 seconds or longer,
depending on the heat in the motor and
the outside temperature).
03 Instruments and controls
Wiper – reversing
Power windows
Engaging reverse gear while the windscreen
wipers are on initiates intermittent rear window wiping23. The function stops when
reverse gear is disengaged.
All power windows can be operated using the
control panel for the driver's door - the control panels for the other doors operate their
respective power window.
If the rear window wiper is already on at continuous speed, no change is made.
WARNING
Check that children or other passengers
are not trapped if the windows are closed,
even when the remote control key is used.
NOTE
On cars with rain sensors, the rear wiper is
activated during reversing if the sensor is
activated and it is raining.
Washer fluid - filling (p. 369)
Washer fluid - quality and volume
(p. 404)
03
WARNING
Related information
•
•
WARNING
Check that no rear seat passengers are
trapped when the windows are closed
from the driver's door.
Driver's door control panel.
Switch for electric child safety locks* and
disengaging rear power window buttons;
see Child safety locks - electrical activation* (p. 177).
If there are children in the car - remember
to always switch off the power supply to
the power windows by selecting key position 0 and then take the remote control key
with you when leaving the car. For information on key positions - see Key positions - functions at different levels (p. 76).
Rear window controls
Front window controls
23
This function (intermittent wiping when reversing) can be deactivated. Visit a workshop. Volvo recommends that you contact an authorised Volvo workshop.
* Option/accessory, for more information, see Introduction.
}}
99
03 Instruments and controls
||
Operating
03
NOTE
Operating the power windows.
One way to reduce the pulsating wind
noise when the rear windows are open is
to also open the front windows slightly.
Operating without auto
Operating without auto
Operating with auto
Move one of the controls up/down gently.
The power windows move up/down as long
as the control is held in position.
All power windows can be operated using the
control panel for the driver's door - the control panels for the other doors can only each
operate their respective power window. Only
one control panel can be operated at a time.
In order for the power windows to be used,
the key position must be at least I - see Key
positions - functions at different levels (p. 76).
The power windows can be operated for a
few minutes after the engine has been
switched off and after the remote control key
has been removed - although not after a door
has been opened.
Closing of the windows is stopped and the
window is opened if anything prevents its
100
movement. It is possible to override the pinch
protection when closing has been interrupted,
e.g. if there is ice forming. After two successive closing interruptions the pinch protection
will be forced and the automatic function
deactivated for a short while, now it is possible to close by continually holding the button
pulled up.
Operating with auto
Move one of the controls up/down to the end
position and release it. The window runs
automatically to its end position.
Operating with the remote control key
and central locking
To remotely operate the power windows from
the outside with the remote control key or
from inside with central locking, see Remote
control key (p. 156) and Locking/unlocking from the inside (p. 172).
Resetting
If the battery is disconnected then the function for automatic opening must be reset so
that it can work correctly.
1. Gently raise the front section of the button to raise the window to its end position
and hold it there for one second.
2. Release the button briefly.
3. Raise the front section of the button again
for one second.
WARNING
A reset must take place for pinch protection to work.
03 Instruments and controls
Door mirrors
WARNING
The door mirror positions are adjusted with
the joystick in the driver's door controls.
Both mirrors are the wide-angle type to
provide optimal vision. Objects may
appear further away than they actually are.
Storing settings24
The settings for the rearview and door mirrors
and the positions of the driver's seat can be
stored for each remote control key in the car
key memory*, see Remote control key - personalisation* (p. 157).
Angling the door mirror when parking24
Door mirror controls.
Adjusting
1. Press the L button for the left-hand door
mirror or the R button for the right-hand
door mirror. The light in the button illuminates.
2. Adjust the position with the joystick in the
centre.
3. Press the L or R button again. The light
should no longer be illuminated.
24
The door mirror can be angled down for the
driver to view the side of the road when parking for example.
–
Engage reverse gear and press the L or R
button.
When reverse gear is disengaged the mirror
automatically returns to its original position
after approx. 10 seconds, or earlier by pressing the button labelled L or R respectively.
Automatic angling of the door mirror
when parking24
The function can be activated/deactivated in
the menu system MY CAR, see MY CAR
(p. 108).
Automatic retraction when locking24
When the car is locked/unlocked with the
remote control key the door mirrors are automatically retracted/extended.
The function can be activated/deactivated in
the menu system MY CAR, see MY CAR
(p. 108).
03
Resetting to neutral
Mirrors that have been moved out of position
by an external force must be reset electrically
to the neutral position for electric retracting/
extending to work correctly:
1. Retract the mirrors with the L and R buttons.
2. Fold them out again with the L and R buttons.
3. Repeat the above procedure as necessary.
The mirrors are now reset in neutral position.
When reverse gear is engaged the door mirror
is automatically angled down so that the
driver can see the side of the road when
parking for example. When reverse gear is
disengaged the mirror automatically returns
to its original position after a short time.
Retractable power door mirrors*
The mirrors can be retracted for parking/driving in narrow spaces:
1. Depress the L and R buttons simultaneously (key position must be at least I).
Only in combination with power seat with memory, see Seats, front - electrically operated (p. 79).
}}
* Option/accessory, for more information, see Introduction.
101
03 Instruments and controls
||
2. Release them after
approximately 1 second. The mirrors
automatically stop in the fully retracted
position.
Fold out the mirrors by pressing down the L
and R buttons simultaneously. The mirrors
automatically stop in the fully extended position.
03
Windows and rearview and door
mirrors - heating
See also Demisting and defrosting the windscreen (p. 132).
The defroster is used to quickly remove misting and ice from the windscreen, rear window
and door mirrors.
The door mirrors and rear window are demisted/defrosted automatically if the car is
started in an outside temperature lower than
+7 °C. Automatic defrosting can be selected
in the menu system MY CAR, see MY CAR
(p. 108).
Heated windscreen*, rear window and
door mirrors
The compass (p. 104) is deactivated when
the heated windscreen is activated. When the
heated windscreen is deactivated, the compass is reactivated.
Home safe and approach lighting
The lamp on the door mirrors illuminates
when approach lighting (p. 93) or home safe
lighting (p. 93) is selected.
Related information
•
•
Rearview mirror - interior (p. 103)
Windows and rearview and door mirrors heating (p. 102)
Heating, windscreen
Heating, rear window and door mirrors
The function is used to remove ice and misting from the windscreen, rear window and
door mirrors.
One press of the respective button starts the
heating. The light in the button indicates that
the function is active. Switch off the heating
as soon as the ice/misting is cleared in order
not to load the battery unnecessarily. However, the function is switched off automatically after a certain time.
102
* Option/accessory, for more information, see Introduction.
03 Instruments and controls
Rearview mirror - interior
The interior rearview mirror can be dimmed
with a control in the mirror's lower edge.
Alternatively, the rearview mirror dims automatically.
Glass roof*
for manual dimming is not available on mirrors with automatic dimming.
The rearview mirror contains two sensors one forward facing and one rearward facing that work together to identify and eliminate
dazzling light. The forward facing sensor
detects ambient light, while the rearward facing sensor detects the light from vehicle
headlights behind.
The glass roof's blind can be operated with
the control in the roof console.
The glass roof is fixed but the power operated roller blind can be operated in key position I or II with the control in the roof console.
For information on key positions - see Key
positions - functions at different levels (p. 76).
03
NOTE
If the sensors are obscured by e.g. parking
permits, transponders, sun visors or
objects in the seats or in the cargo area in
such a way that light is prevented from
reaching the sensors, then the dimming
function of the rearview mirror is reduced.
Control for dimming
Manual dimming
Bright light from behind could be reflected in
the rearview mirror and dazzle the driver. Use
dimming with the dimming control when
lights from behind are distracting:
The compass (p. 104) can only be specified
for a rearview mirror with automatic dimming.
Related information
•
Door mirrors (p. 101)
Automatic opening to end position
Manual opening until the button is
released
1. Use dimming by moving the control in
towards the passenger compartment.
Manual closing until the button is
released
2. Return to normal position by moving the
control towards the windscreen.
Automatic closing to end position
Automatic dimming*
Bright light from behind is automatically
dimmed by the rearview mirror. The control
}}
* Option/accessory, for more information, see Introduction.
103
03 Instruments and controls
IMPORTANT
•
Avoid touching the blind because it
may then be damaged.
•
Only use the control in the roof console to operate the blind.
Compass
The rearview mirror contains an integrated
display that shows the compass direction in
which the front of the car is pointing.
Operation
side of the mirror using a paper clip for example.
The compass is deactivated when the heated
windscreen is activated. When the heated
windscreen is deactivated, the compass is
reactivated.
Calibration
The earth is divided into 15 magnetic zones.
The compass is set for the geographic area to
which the car was delivered. The compass
should be calibrated if the car is moved
across several magnetic zones. Proceed as
follows:
03
1. Stop the car in a large open area free
from steel structures and high-voltage
power lines.
Rearview mirror with compass.
The upper right-hand corner of the rearview
mirror has an integrated display that shows
the compass direction in which the front of
the car is pointing. Eight different directions
are shown with English abbreviations: N
(north), NE (north east), E (east), SE (south
east), S (south), SW (south west), W (west)
and NW (north west).
The compass* is activated automatically
when the car is started or when key position
II is active, see Key positions - functions at
different levels (p. 76). To deactivate/activate
the compass - press in the button on the rear
104
* Option/accessory, for more information, see Introduction.
2. Start the car.
NOTE
For the best calibration, switch off all electrical equipment (climate control system,
wipers, etc.) and makes sure that all doors
are closed.
3. Hold the button on the underside of the
rearview mirror depressed
approx. 3 seconds. The number of the
current magnetic zone is shown.
03 Instruments and controls
Menu navigation - combined
instrument panel
The menus shown on the information display
in the combined instrument panel (p. 61) are
controlled with the left-hand stalk switch.
Which menus are shown depends on the key
position (p. 76).
G030295
03
Magnetic zones.
Information displays (digital combined instrument
panel) and controls for menu navigation.
4. Press the button repeatedly until the
required magnetic zone (1–15) is shown.
See the map of magnetic zones for the
compass.
5. Wait until the display returns to showing
the character C, or hold the button on the
bottom of the rearview mirror depressed
for approx. 6 seconds (use e.g. a paper
clip) until the character C is shown.
6. Drive slowly in a circle at a speed of no
more than 10 km/h until a compass direction is shown in the display, indicating
that calibration is complete. Then drive a
further 2 circles to fine-tune calibration.
7. Repeat the above procedure as necessary.
OK - access the menu, acknowledge
messages and confirm menu selections.
Thumbwheel – browse between menu
options.
Information display (analogue combined instrument panel) and menu navigation controls.
RESET - reset data in the selected trip
computer step and go back in the menu
structure.
If there is a message (p. 106) then it must be
acknowledged with OK in order that the
menus shall be shown.
Related information
•
•
•
Messages - handling (p. 107)
Menu overview - analogue combined
instrument panel (p. 106)
Menu overview - digital combined instrument panel (p. 106)
105
03 Instruments and controls
03
Menu overview - analogue combined
instrument panel
Menu overview - digital combined
instrument panel
Which menus are shown in the combined
instrument panel's information display
depends on the key position (p. 76).
Which menus are shown in the combined
instrument panel's information display
depends on the key position (p. 76).
Some of the following menu options require
the function and hardware to be installed in
the car.
Some of the following menu options require
the function and hardware to be installed in
the car.
Digital speed
Settings*
Parking heater*
Themes
Additional heater*
Contrast mode/Colour mode
TC options
Service status
Service status
Messages27
Oil level25
Oil level28
Messages (##)26
Parking heater*
Related information
•
Menu navigation - combined instrument
panel (p. 105)
•
Menu overview - digital combined instrument panel (p. 106)
•
25
26
27
28
106
Combined instrument panel (p. 61)
Trip computer reset
Related information
•
Menu navigation - combined instrument
panel (p. 105)
•
Menu overview - analogue combined
instrument panel (p. 106)
•
Combined instrument panel (p. 61)
Certain engines.
The number of messages is indicated in brackets.
The number of messages is indicated in brackets.
Certain engines.
* Option/accessory, for more information, see Introduction.
Messages
When a warning, information or indicator
symbol illuminates, a corresponding message
appears on the information display.
Message
Specification
Stop safelyA
Stop and switch off the
engine. Serious risk of
damage - consult a workshopB.
Stop engineA
Stop and switch off the
engine. Serious risk of
damage - consult a workshopB.
Service
urgentA
Contact a workshopB to
check the car immediately.
Service
requiredA
Contact a workshopB to
check the car as soon as
possible.
See manualA
Read the owner's manual.
Book time
for maintenance
Time to book regular
service - contact a workshopB.
03 Instruments and controls
Message
Specification
Message
Specification
Time for regular maintenance
Time for regular service contact a workshopB. The
timing is determined by
the number of kilometres
driven, number of months
since the last service,
engine running time and
oil grade.
Transmission
hot Stop
safely Wait
for cooling
Critical fault. Stop the car
immediately in a safe
manner and contact a
workshopB.
Temporarily
offA
A function has been temporarily switched off and
is reset automatically
while driving or after starting again.
Low battery
charge
Power save
mode
The audio system is
switched off to save
energy. Charge the battery.
Maintenance
overdue
If the service intervals are
not followed then the
warranty does not cover
any damaged parts contact a workshopB.
Transmission
Oil change
needed
Contact a workshopB to
check the car as soon as
possible.
Transmission
Reduced
performance
The gearbox cannot handle full capacity. Drive
with care until the message clearsC.
If shown repeatedly contact a workshopB.
Transmission
hot Reduce
speed
A
B
C
Messages - handling
Use the left-hand stalk switch to acknowledge
and browse among messages (p. 106) that
are shown in the information display of the
combined instrument panel.
When a warning, information or indicator
symbol illuminates, a corresponding message
is shown in the display. An error message is
stored in a memory list until the fault has
been rectified.
03
Press OK on the left-hand stalk switch to
acknowledge29 a message. Scroll through
messages with the thumbwheel (p. 105).
NOTE
If a warning message appears while you
are using the trip computer, the message
must be read (press OK) before the previous activity can be resumed.
Part of message, shown together with information on
where the problem has arisen.
An authorised Volvo workshop is recommended.
For more messages concerning automatic gearbox.
Related information
•
•
Messages - handling (p. 107)
Menu navigation - combined instrument
panel (p. 105)
Related information
•
Menu overview - analogue combined
instrument panel (p. 106)
•
Menu overview - digital combined instrument panel (p. 106)
Drive more smoothly or
stop the car in a safe
manner. Disengage the
gear and run the engine
at idling speed until the
message clearsC.
107
03 Instruments and controls
MY CAR
vary, depending on the equipment selected and
the market.
MY CAR is a menu source that handles many
of the car's functions, e.g. City Safety™, locks
and alarm, automatic fan speed, setting the
clock, etc.
03
MY CAR - opens the menu system MY
CAR.
OK/MENU - press the button in the centre console or the thumbwheel on the
steering wheel to select/tick in the highlighted menu option or store the selected
function in the memory.
Certain functions are standard, others are
optional - the range also varies depending on
the market.
TUNE - turn the knob in the centre console or the thumbwheel on the steering
wheel to scroll up/down through the
menu options.
Operation
Navigation in the menus is carried out using
buttons in the centre console or with the
steering wheel's right-hand keypad*.
EXIT
EXIT functions
Depending on the function the cursor is on
when EXIT is depressed briefly, and on which
menu level, one of the following may occur:
•
•
•
•
•
Control panel in centre console and steering
wheel keypad. The figure is schematic - the number of functions and layout of the buttons both
29
108
A message can also be acknowledged via the thumbwheel or RESET button.
* Option/accessory, for more information, see Introduction.
phone call is rejected
current function is interrupted
input characters are deleted
most recent selections are undone
leads up in the menu system.
A long press on EXIT leads to the normal
view for MY CAR or if you are in the normal
view, to the highest menu level (main source
menu).
03 Instruments and controls
Menu options and search paths
Trip computer
For a description of the menu options and
search paths in MY CAR, see the Sensus
Infotainment supplement.
The car's trip computer can record, calculate
and show information.
Related information
General
Checking and settings can be made immediately after the combined instrument panel is
automatically illuminated in connection with
unlocking. If none of the trip computer's controls are actuated within approx. 30 seconds
after the driver's door has been opened then
the instrument extinguishes, after which
either key position II (p. 76) or engine starting
is required in order to operate the trip computer.
•
Trip computer - analogue combined
instrument panel (p. 110)
•
Trip computer - digital combined instrument panel (p. 114)
•
Trip computer - supplementary information (p. 118)
•
Trip computer - trip statistics* (p. 119)
03
NOTE
If a warning message appears when the
trip computer is used then the message
must first be acknowledged before the trip
computer can be reactivated.
•
Acknowledge the message by briefly
pressing the indicator stalk OK button.
Group menus
The trip computer has two different group
menus:
•
•
Functions
Heading in combined instrument panel
The trip computer's functions or headings
are each listed in an infinite loop.
* Option/accessory, for more information, see Introduction.
109
03 Instruments and controls
Trip computer - analogue combined
instrument panel
The trip computer's menu is in a variable
loop. One of the alternatives is that the trip
computer's display extinguishes - this also
marks the start/end of the loop.
03
Functions
Proceed as follows to open and check/adjust
functions:
1. To ensure that no control is in the middle
of a sequence - "Reset" them first with
two presses on RESET.
2. Press OK - the loop with all functions
opens.
3. Browse through the functions with the
thumbwheel and select/confirm with OK.
4. Finish by pressing twice on RESET after
completed checking/adjustment.
The different functions of the trip computer
are listed in the following table:
Information display and controls.
OK - Opens the loop with the trip computer's functions + Activates the selected
option.
Thumbwheel - Opens the loop with the
trip computer's headings + Scrolls
through the options.
RESET - Undoes, zeroes or backs out of
a function after making a selection.
110
03 Instruments and controls
Functions
Information
Digital speed
Shows the car's speed digitally in the centre of the combined instrument panel:
•
•
•
•
km/h
Open with OK, select with the thumbwheel, confirm with OK and back out with ENTER.
mph
No display
Parking heater*
•
•
DIRECT START
•
- Timer 2 - leads to the menu for selecting time.
For a description of programming the timer, see Engine block heater and passenger compartment heater* - timer (p. 138).
03
- Timer 1 - leads to the menu for selecting time.
Additional heater*
For more information, see Additional heater* (p. 140).
• Auto On
• Off
TC options
•
•
•
•
•
Distance to empty tank
Fuel consumption
Average speed
Trip meter T1 and total dist.
Trip meter T2 and total dist.
Here you can select/activate the options that you want to be available as selectable headings in
the trip computer. The symbols for the items already selected are WHITE with a "tick" - others are
GREY and have no "tick":
1. Open the function with OK, scroll through the symbols for the options with the thumbwheel
and select/stop on the desired symbol.
2. Confirm with OK - the symbol changes colour from GREY to WHITE and is marked with a
"tick".
3. Continue to select the function symbols with the thumbwheel or finish with RESET.
Service status
Shows the number of months and the distance until the next service.
}}
* Option/accessory, for more information, see Introduction.
111
03 Instruments and controls
||
A
03
Functions
Information
Oil levelA
For more information, see Engine oil - checking and filling (p. 354).
Messages (##)
For more information, see Messages (p. 106).
Certain engines.
Headings
One of the headings in the following table can
be selected for constant display in the combined instrument panel. Proceed as follows to
determine which:
3. Stop on desired heading.
2. Turn the thumbwheel - selectable headings for the trip computer are shown in a
loop.
Trip computer heading in combined instrument
panel
Information
Trip meter T1 and total dist.
•
Long press on RESET resets trip meter T1.
Trip meter T2 and total dist.
•
Long press on RESET resets trip meter T2.
Distance to empty
For more information - see the section "Range - distance to empty tank" (p. 118).
Fuel consumption
Current consumption.
Average speed
•
No trip computer information.
This option shows a blank display - it also marks the beginning/end of the loop.
The combined instrument panel's trip computer can be changed to another option at
any time during the journey. Proceed as follows:
112
1. To ensure that no control is in the middle
of a sequence - "Reset" them first with
two presses on RESET.
•
Long press on RESET resets Average speed.
Turn the thumbwheel - stop on the
desired heading.
Resetting - Trip meter and Average
speed
With the current trip computer heading - T1
and total dist.,T2 and total dist. or
03 Instruments and controls
Average speed - shown in the combined
instrument panel:
•
Give a long press on RESET RESET selected heading is zeroed.
Each heading must be zeroed individually.
Related information
•
•
Trip computer (p. 109)
03
Trip computer - digital combined instrument panel (p. 114)
•
Trip computer - supplementary information (p. 118)
•
Trip computer - trip statistics* (p. 119)
* Option/accessory, for more information, see Introduction.
113
03 Instruments and controls
Trip computer - digital combined
instrument panel
The trip computer's menu is in a variable
loop. One of the alternatives is that the trip
computer's three displays extinguish - this
also marks the start/end of the loop.
Functions
Proceed as follows to open and check/adjust
functions:
1. To ensure that no control is in the middle
of a sequence - "Reset" them first with
two presses on RESET.
2. Press OK - loop with all functions opens.
3. Browse through the functions with the
thumbwheel and select/confirm with OK.
03
4. Finish by pressing twice on RESET after
completed checking/adjustment.
The different functions of the trip computer
are listed in the following table:
Information displays and controls.
OK - Opens the loop with the trip computer's functions + Activates the selected
option.
Thumbwheel - Opens the loop with the
trip computer's headings + Scrolls
through the options.
RESET - Undoes, zeroes or backs out of
a function after making a selection.
114
03 Instruments and controls
Functions
Information
Trip computer reset
Note that this function does not reset both trip meters T1 and T2 - see table under next section
"Headings" and section "Resetting - Average speed/consumption" for information on the process.
•
•
Average
Average speed
Messages
For more information, see Messages (p. 106).
Themes
Combined instrument panel appearance is selected here, see Digital combined instrument panel
- overview (p. 62).
Settings*
Select Auto On or Off.
03
For more information, see Additional heater* (p. 140).
Contrast mode/Colour mode
Adjusting the combined instrument panel's brightness and colour intensity.
Parking heater*
For a description of programming the timer, see Engine block heater and passenger compartment heater* - timer (p. 138).
• Direct start
• - Symbol Timer 1 - leads to the menu for
selecting time.
•
A
- Symbol Timer 2 - leads to the menu for
selecting time.
Service status
Shows the number of months and the distance until the next service.
Oil levelA
For more information, see Engine oil - checking and filling (p. 354).
Certain engines.
}}
* Option/accessory, for more information, see Introduction.
115
03 Instruments and controls
||
Headings
One of the heading combinations in the following table can be selected for constant display in the combined instrument panel. Proceed as follows to determine which:
1. To ensure that no control is in the middle
of a sequence - "Reset" them first with
two presses on RESET.
2. Turn the thumbwheel - selectable heading combinations are shown in a loop.
03
3. Stop on desired heading combination.
Three trip computer headings can be displayed
simultaneously - one in each "window".
Heading combinations
Information
Average
Trip meter T1 + Meter reading
Average speed
•
Long press on RESET resets trip meter T1.
Instantaneous
Trip meter T2 + Meter reading
Distance to empty
tank
•
Long press on RESET resets trip meter T2.
Instantaneous
Meter reading
kmh<>mph
No trip computer information.
The combined instrument panel's heading
combination for the trip computer can be
changed to another option at any time during
the journey. Proceed as follows:
116
kmh<>mph - "Digital speed display", see Trip computer - supplementary information (p. 118).
This option extinguishes all three trip computer displays - it also marks
the beginning/end of the loop.
•
Turn the thumbwheel - stop on the
desired heading.
Resetting - Trip meter
Turn with the thumbwheel to the heading
combination containing the trip meter to be
reset:
03 Instruments and controls
•
Give a long press on RESET RESET selected trip meter is zeroed.
Resetting - Average speed/
consumption
1. Select function Trip computer
reset and activate with OK.
2. Select one of the following options with
the thumbwheel and activate with OK:
•
•
•
03
l/100 km
km/h
Reset both
3. Finish with RESET.
Related information
•
•
Trip computer (p. 109)
Trip computer - analogue combined
instrument panel (p. 110)
•
Trip computer - supplementary information (p. 118)
•
Trip computer - trip statistics* (p. 119)
* Option/accessory, for more information, see Introduction.
117
03 Instruments and controls
Trip computer - supplementary
information
Supplementary information covering several
functions follows below.
Average
Average fuel consumption is calculated from
the last resetting.
03
NOTE
There may be a slight error in the reading if
a fuel-driven heater* has been used.
Average speed
The average speed is calculated for the driving distance driven since the last reset to
zero.
Instantaneous
The information for current fuel consumption
is updated continuously - approximately once
per second. When the car is driven at low
speed the consumption is shown per time
unit - at a higher speed it is shown related to
mileage.
Different units (km/miles) can be selected for
the display - see section below."Change unit"
(p. 118)
30
118
Range - distance to empty tank
Change unit
The trip computer shows the approximate
distance that can be driven with the fuel
quantity remaining in the tank.
You can change unit (km/miles) for distance
and speed in the menu system MY CAR, see
MY CAR (p. 108).
No guaranteed range remains when the heading Distance to empty shows "----".
•
NOTE
In addition to in the trip computer, these
units are also changed in Volvo's navigation system*.
In which case, refuel as soon as possible.
The calculation is based on the average fuel
consumption over the last 30 km and the
remaining driveable fuel quantity.
NOTE
There may be a slight error in the reading if
the driving style has been changed.
An economic driving style generally results in
a longer driving distance. For more information on how fuel consumption can be influenced, see Volvo Cars' environmental philosophy (p. 21).
Digital speed display30
The speed is shown in the opposite unit
(kmh/mph) of the main instrument panel. If it
is calibrated in mph then the trip computer
shows the corresponding speed in km/h and
vice versa.
Only with the combined instrument panel "Digital".
* Option/accessory, for more information, see Introduction.
Related information
•
•
Trip computer (p. 109)
Trip computer - analogue combined
instrument panel (p. 110)
•
Trip computer - digital combined instrument panel (p. 114)
•
Trip computer - trip statistics* (p. 119)
03 Instruments and controls
Trip computer - trip statistics*
Operation
Information is stored about completed trips
containing average fuel consumption and
average speed, which can be viewed in the
centre console's screen as a bar chart.
Different settings can be made in the menu
system MY CAR, see MY CAR (p. 108) there, find Trip statistics.
Function
•
Trip computer - supplementary information (p. 118)
With the "Reset when vehicle has been off
for minimum 4h" option highlighted, all statistics are deleted automatically once driving
is complete and the car has been stopped for
4 hours. The journey statistics start again
from zero the next time the engine is started.
03
• Reset when vehicle has been off for
minimum 4h - highlight the box by
selecting ENTER and go back out of the
menu by selecting EXIT.
Trip statistics31.
Each bar symbolises 1 km or 10 km driven
distance, depending on the scale selected the bar at the far right shows the value for the
current kilometre or 10 km.
The TUNE knob can be used to change the
scale for each bar between 1 km and 10 km the cursor at the far right changes position
between up and down depending on the
scale selected.
31
If a new drive cycle begins before 4 hours
have passed, the current period has to be
deleted manually first using the "Start new
trip" option.
• Start new trip - ENTER is used to delete
all previous statistics, back out of the
menu by selecting EXIT.
See also information on Eco guide (p. 65).
Related information
•
•
•
Trip computer (p. 109)
Trip computer - analogue combined
instrument panel (p. 110)
Trip computer - digital combined instrument panel (p. 114)
The figure is schematic - layout may vary depending on updated software and market.
* Option/accessory, for more information, see Introduction.
119
CLIMATE CONTROL
04 Climate control
General information on climate
control
The car is equipped with electronic climate
control. The climate control system cools or
heats as well as dehumidifies the air in the
passenger compartment.
•
•
When the engine requires full power, e.g.
for full acceleration or driving uphill with a
trailer, the air conditioning can be temporarily switched off. There may then be a
temporary increase in temperature in the
passenger compartment.
•
Remove misting on the insides of the windows primarily by using the defroster
function (p. 132). To reduce the risk of
misting, keep the windows clean and use
window cleaner.
There are two different climate control systems:
•
Electronic temperature control
(ETC) (p. 128)
•
Electronic climate control (ECC) (p. 127)
NOTE
Air conditioning (AC) (p. 131) can be
switched off, but to ensure the best possible climate comfort in the passenger compartment, and to prevent the windows
from misting, it should always be switched
on.
To bear in mind
•
To ensure that the air conditioning works
optimally, the side windows must be
closed.
•
Total airing function (p. 173) opens/
closes all side windows simultaneously
and can be used for example to quickly
air the car during hot weather.
•
Remove ice and snow from the climate
control system air intake (the grille
between the bonnet and the windscreen).
In warm weather, condensation from the
air conditioning may drip under the car.
This is normal.
NOTE
When the ECO function is activated, several parameters in the climate control system's settings are changed, and several
electricity consumer functions are
reduced. Certain settings can be reset
manually, but full functionality is only
restored by deactivating the ECO function.
Related information
Cars with Start/Stop*
•
•
•
•
With an auto-stopped (p. 277) engine certain
equipment may have its function temporarily
reduced, e.g. climate control fan speed
(p. 130).
•
•
•
Actual temperature (p. 122)
Sensors - climate control (p. 122)
Menu settings - climate control (p. 124)
04
Air distribution in the passenger compartment (p. 125)
Air cleaning (p. 122)
Heated front seats* (p. 129)
Heated rear seat* (p. 129)
Cars with ECO*
Certain equipment may have its function temporarily reduced or deactivated when the
ECO (p. 286) function is activated, e.g. the air
conditioning (p. 131).
* Option/accessory, for more information, see Introduction.
121
04 Climate control
04
Actual temperature
Sensors - climate control
Air cleaning
The temperature you select in the passenger
compartment corresponds to the physical
experience with reference to factors such as
ambient temperature, air speed, humidity and
solar radiation etc. in and around the car at
the time.
The climate control system has a number of
sensors to help control the temperature
(p. 122) in the car.
The interior in a passenger compartment is
designed to be pleasant and comfortable,
even for people with contact allergies and for
asthma sufferers.
The system includes a sun sensor (p. 122)
which detects on which side the sun is shining into the passenger compartment. This
means1 that the temperature can differ
between the right and left-hand air vents
despite the controls being set for the same
temperature on both sides.
•
The sun sensor is located on the top side
of the dashboard.
•
The temperature sensor for the passenger compartment is located below the climate control panel.
•
The outside temperature sensor is
located in the door mirror.
NOTE
Do not cover or block the sensors with
clothing or other objects.
Related information
•
General information on climate control
(p. 121)
•
Temperature control in the passenger
compartment (p. 131)
1
122
Related information
•
Only applies to ECC.
* Option/accessory, for more information, see Introduction.
General information on climate control
(p. 121)
•
•
Passenger compartment filter (p. 123)
Material in the passenger compartment (p. 124)
•
Clean Zone Interior Package
(CZIP) (p. 123)*
•
Interior Air Quality System
(IAQS) (p. 124)*
Related information
•
General information on climate control
(p. 121)
04 Climate control
Air cleaning - passenger
compartment filter
Air cleaning - Clean Zone Interior
Package (CZIP)*
All air entering the car's passenger compartment is cleaned with a filter.
CZIP comprises a series of modifications that
keep the passenger compartment even
clearer from allergy and asthma-inducing substances.
The filter must be replaced at regular intervals. Follow the Volvo Service Programme for
the recommended replacement intervals. If
the car is used in a severely contaminated
environment, it may be necessary to replace
the filter more often.
The following is included:
•
NOTE
There are different types of passenger
compartment filter. Make sure that the correct filter is fitted.
Related information
•
Air cleaning (p. 122)
NOTE
To maintain the CZIP standard in cars with
CZIP the IAQS filter should be changed
after 15 000 km or once per year depending on whichever occurs first. However, up
to 75 000 km over 5 years. In cars without
CZIP and where the customer does not
want to retain the CZIP standard, the IAQS
filter must be replaced during a regular
service.
•
An enhanced fan function that means that
the fan starts when the car is opened with
the remote control key. The fan fills the
passenger compartment with fresh air.
The function starts when required and is
disengaged automatically after a time or
when one of the passenger compartment
doors is opened. The amount of time the
fan runs is reduced gradually due to
reduced need up until the car is 4 years
old.
For more information on CZIP, see the brochure included with the purchase of the car.
Related information
•
General information on climate control
(p. 121)
•
Air cleaning (p. 122)
04
The air quality system IAQS (p. 124) is a
fully automatic system that cleans the air
in the passenger compartment from contaminants such as particles, hydrocarbons, nitrous oxides and ground-level
ozone.
* Option/accessory, for more information, see Introduction.
123
04 Climate control
Air cleaning - IAQS*
Air cleaning - material
Menu settings - climate control
The air quality system IAQS separates gases
and particles to reduce the levels of odours
and pollution in the passenger compartment.
Tested materials have been developed in
order to minimise the quantity of dust in the
passenger compartment and to contribute to
making the passenger compartment easier to
keep clean.
It is possible to activate/deactivate or change
the default settings for four of the climate
control system's functions via the centre console.
If the outside air is contaminated then the air
intake is closed in order to shut out hydrocarbons, nitrous oxides and ground-level ozone.
The air is recirculated in the passenger compartment.
04
It is possible to activate/deactivate the function in the menu system MY CAR. For a
description of the menu system, see MY CAR
(p. 108).
The carpets in both the passenger compartment and the cargo area are removable and
easy to remove and clean. Use cleaning
agents and car care products recommended
by Volvo to clean the interior (p. 388).
Related information
•
NOTE
The air quality sensor must always be enabled to ensure the best air in the passenger compartment.
In a cold climate, automatic recirculation is
limited so as to prevent misting.
Related information
•
•
•
124
General information on climate control
(p. 121)
Air cleaning (p. 122)
Air cleaning - Clean Zone Interior Package (CZIP)* (p. 123)
* Option/accessory, for more information, see Introduction.
Air cleaning (p. 122)
•
•
•
•
Fan level during automatic climate control
(p. 130)*.
Recirculation timer (p. 133).
Automatic start of rear window defroster
(p. 102).
Interior air quality system (p. 124)*.
The climate control system's functions can be
reset to the default settings via the menu system in MY CAR. For a description of the
menu system, see MY CAR (p. 108).
Related information
•
General information on climate control
(p. 121)
04 Climate control
Air distribution in the passenger
compartment
Air vents in the dashboard
Air distribution
The incoming air is divided between a number
of different vents in the passenger compartment.
Air distribution is fully automatic in AUTO
mode*.
If necessary it can be controlled manually;
see the air distribution table (p. 134).
Open
Air distribution - defroster windscreen
Closed
Air distribution - air vent instrument panel
Lateral airflow
Air distribution - ventilation floor
Vertical airflow
Aim the vents at the side windows to remove
misting.
NOTE
Remember that small children may be sensitive to air flows and draughts.
04
The figure consists of three buttons. When
pressing the buttons the corresponding figure
is illuminated in the display screen (see figure
below) and an arrow in front of each part of
the figure shows the air distribution that is
selected. For more information, see the air
distribution table (p. 134).
}}
* Option/accessory, for more information, see Introduction.
125
04 Climate control
||
04
The selected air distribution is shown in the centre console display screen.
Related information
126
•
General information on climate control
(p. 121)
•
•
Auto-regulation (p. 130)
Air distribution - recirculation (p. 133)
04 Climate control
Electronic climate control - ECC*
ECC (Electronic Climate Control) maintains
the temperature selected in the passenger
compartment and can be set separately for
the driver's side and passenger side.
The auto function is used to automatically
control temperature, air conditioning, fan
speed, recirculation and air distribution.
04
Fan (p. 130)
AUTO - Automatic climate control
(p. 130)
Electrically heated front seat (p. 129), left
side
Heated windscreen and max.
defroster (p. 132)*
Related information
Rear window and door mirror defrosters (p. 102)
•
Setting, left/right-hand side for temperature control (p. 131)
General information on climate control
(p. 121)
Electrically heated front seat (p. 129),
right side
Temperature control (p. 131)
Air distribution (p. 125) - ventilation floor
Recirculation (p. 133)
Air distribution - air vent instrument panel
ECO* (p. 286)
Air distribution - defroster windscreen
AC - Air conditioning on/off (p. 131)
* Option/accessory, for more information, see Introduction.
127
04 Climate control
Electronic temperature control - ETC
The passenger compartment's climate comfort is controlled manually using the ETC
(Electronic Temperature Control).
04
Fan (p. 130)
Rear window and door mirror defrosters (p. 102)
Electrically heated front seat (p. 129), left
side
Recirculation (p. 133)
AC - Air conditioning on/off (p. 131)
Electrically heated front seat (p. 129),
right side
Heated windscreen and max. defroster*
Temperature control (p. 131)
Air distribution (p. 125) - ventilation floor
Air distribution - air vent instrument panel
Air distribution - defroster windscreen
128
ECO* (p. 286)
Related information
•
* Option/accessory, for more information, see Introduction.
General information on climate control
(p. 121)
04 Climate control
Heated front seats*
•
The front seat heating has three positions for
increasing the comfort for driver and passenger when it is cold.
Lowest heat level - one orange field illuminates in the screen.
•
Switch off the heat - no field illuminates.
WARNING
Heated rear seat*
The heating for the rear seat's outer positions
has three positions for increasing the comfort
for passengers when it is cold.
Heated seats must not be used by people
who find it difficult to perceive an increase
in temperature due to a lack of sensation
or who otherwise have problems operating
the controls for the heated seats. Otherwise they may suffer burn injuries.
Related information
Current heat level is shown in the centre console
display screen.
•
General information on climate control
(p. 121)
•
Heated rear seat* (p. 129)
04
Current heat level is shown in the pushbutton's
lamps:
Press the button repeatedly in order to activate the function:
•
Press the button repeatedly in order to activate the function:
•
Highest heat level - three orange fields
illuminate in the centre console's screen
(see figure above).
•
Lower heat level - two orange fields illuminate in the screen.
•
•
•
Highest heat level - three lamps illuminate.
Lower heat level - two lamps illuminate.
Lowest heat level - one lamp illuminates.
Switch off the heat - no lamp illuminates.
}}
* Option/accessory, for more information, see Introduction.
129
04 Climate control
||
WARNING
Heated seats must not be used by people
who find it difficult to perceive an increase
in temperature due to a lack of sensation
or who otherwise have problems operating
the controls for the heated seats. Otherwise they may suffer burn injuries.
Fan
Auto-regulation
The fan should always be activated in order to
avoid misting on the windows.
Auto-regulation is only possible in electronic
climate control (ECC) (p. 127).
The auto function automatically regulates temperature
(p. 131), air conditioning
(p. 131), fan speed (p. 130),
recirculation (p. 133) and air
distribution (p. 125).
NOTE
If the fan is fully switched off then the air
conditioning is not engaged - which can
cause a risk of misting on the windows.
Related information
•
General information on climate control
(p. 121)
•
Heated front seats* (p. 129)
ECC*
Turn the knob to increase or
decrease fan speed, AUTO
is disengaged. If AUTO is
selected, then the fan speed
is regulated automatically
(p. 130) - the fan speed previously set is disengaged.
04
ETC
Turn the knob to increase or
decrease fan speed.
Related information
130
•
General information on climate control
(p. 121)
•
•
Electronic climate control - ECC* (p. 127)
* Option/accessory, for more information, see Introduction.
Electronic temperature control - ETC
(p. 128)
If you select one or more manual functions,
the other functions continue to be controlled
automatically. All manual settings are disengaged when AUTO is pressed. The display
screen shows AUTO CLIMATE.
Fan speed in automatic mode can be set in
the menu system MY CAR. For a description
of the menu system, see MY CAR (p. 108).
Related information
•
General information on climate control
(p. 121)
04 Climate control
Temperature control in the passenger
compartment
When the car is started, the most recent temperature setting is resumed.
NOTE
Heating or cooling cannot be hastened by
selecting a higher or lower temperature
than the actual desired temperature.
ECC*
The temperatures on the
driver and passenger sides
can be set independently.
Repeatedly press L/R in the
button to select the setting
for left, right or both sides.
Set the temperature using
the knob - the selected temperature for either
side is displayed in the centre console display.
ETC
The temperature in the passenger compartment can be
adjusted with the knob.
Air conditioning
The air conditioning cools and dehumidifies
incoming air as required.
When the lamp in the AC
button illuminates, the air
conditioning is controlled by
the system's automatic function.
When the lamp in the AC
button is switched off the air conditioning is
disconnected. Other functions are still controlled automatically. When the max.
defroster function (p. 132) is activated, the air
conditioning is switched on automatically so
that the air is dehumidified at the maximum
setting.
04
Related information
Current temperature for each side is shown in
the centre console's display screen.
•
General information on climate control
(p. 121)
•
•
Actual temperature (p. 122)
•
Electronic climate control - ECC* (p. 127)
Electronic temperature control - ETC
(p. 128)
* Option/accessory, for more information, see Introduction.
131
04 Climate control
Demisting and defrosting the
windscreen
Heated windscreen* and max. defroster are
used to quickly remove misting and ice from
the windscreen and side windows.
For cars without heated windscreens:
•
Air flows to the windows - symbol (2) illuminates in the screen.
•
Switch off the function - no symbol illuminates.
For cars with heated windscreens:
04
•
Start the heating for the
symbol (1) illuminates in the screen.
•
Start the heating for the windscreen2 and
air flow to the windows - symbols (1) and
(2) illuminate in the screen.
•
Switch off the function - no symbol illuminates.
windscreen2
NOTE
Electrically heated windscreen is not available when the engine is auto-stopped
(p. 277).
The following also takes place when the function is active in order to provide maximum
dehumidification in the passenger compartment:
•
the air conditioning is automatically
engaged
•
recirculation and the air quality system
are automatically disengaged.
NOTE
NOTE
The selected setting is shown in the centre console display screen.
Heated windscreen*
Heated windscreen and IR window (p. 19)
may have an impact on the performance of
transponders and other communication
equipment.
Max. defroster
The light in the defroster button illuminates when the
function is active.
NOTE
A triangular area at the end of each side of
the windscreen is not electrically heated,
where de-icing may take longer.
Press the button repeatedly
in order to activate the function.
2
132
The compass goes off when the heated windscreen is active.
* Option/accessory, for more information, see Introduction.
The noise level increases as the fan is
operating at max.
When the defroster is switched off the climate
control returns to the previous settings.
Related information
•
General information on climate control
(p. 121)
04 Climate control
Air distribution - recirculation
Select recirculation to shut out bad air,
exhaust gases etc. from the passenger compartment, i.e. no outside air is taken into the
car when this function is activated.
When recirculation is
engaged the orange lamp in
the button illuminates.
IMPORTANT
Related information
•
General information on climate control
(p. 121)
•
Air distribution in the passenger compartment (p. 125)
•
Air distribution - table (p. 134)
04
If the air in the car recirculates for too long,
there is a risk of misting on the insides of
the windows.
Timer
With the timer function activated the system
will exit manually activated recirculation mode
according to a time that depends on the outside temperature. This reduces the risk of ice,
misting and bad air.
It is possible to activate/deactivate the function in the menu system MY CAR. For a
description of the menu system, see MY CAR
(p. 108).
NOTE
When max. defroster is selected, recirculation is always deactivated.
133
04 Climate control
Air distribution - table
Three buttons are used to select the distribution (p. 125) of the air.
04
134
Air distribution
Use
A large amount of hot air flows to the windows.
to remove ice and misting quickly.
Air to windscreen, via defroster vent, and side windows. Some
air flows from the air vents.
to prevent misting and icing in a cold and humid climate,
(not at too low fan speed to enable this).
Airflow to windows and from dashboard air vents.
to ensure good comfort in warm, dry weather.
Airflow to the head and chest from the dashboard air vents.
to ensure efficient cooling in warm weather.
04 Climate control
Air distribution
Use
Air to the floor and windows. Some air flows from the dashboard air vents.
to ensure comfortable conditions and good demisting in
cold or humid weather.
Air to floor and from dashboard air vents.
in sunny weather with cool outside temperatures.
04
Air to floor. Some air flows to the dashboard air vents and windows.
to direct heat or cold to the floor.
Airflow to windows, from dashboard air vents and to the floor.
to provide cooling along the floor in hot, dry weather or
warming upwards in cold weather.
Related information
•
General information on climate control
(p. 121)
•
Air distribution - recirculation (p. 133)
135
04 Climate control
Engine block heater and passenger
compartment heater*
Refuelling
Preconditioning prepares the heater, engine
and passenger compartment before departure so that both wear and energy needs during the journey are reduced. Warming up your
car will also extend the driving distance.
appears in the display. Acknowledge the
message by pressing the indicator stalk
(p. 105) OK button once.
IMPORTANT
Repeated use of the heater in combination
with short driving distances may cause low
charge level in the starter battery, this can
lead to the heater stopping or never starting. In the worst case, engine starting will
not be possible.
The heater can be started directly (p. 137) or
with a timer (p. 138).
04
The heater cannot start if the outside temperature exceeds 15 °C. At –5 °C or lower the
maximum running time of the heater is 50
minutes.
Warning label on fuel filler flap.
WARNING
WARNING
Do not use the fuel-driven heater indoors.
Exhaust gases are secreted.
NOTE
When the fuel-driven auxiliary heater is
active there may be smoke from underneath the car, which is perfectly normal.
Fuel which spills out could be ignited.
Switch off the fuel-driven auxiliary heater
before starting to refuel.
Check in the combined instrument panel
that the heater is switched off. The heat
symbol is shown when it is operating.
Parking on a hill
If the car is parked on a steep hill, the front of
the car should point downhill to ensure that
there is a supply of fuel to the fuel-driven
heater.
Battery and fuel
If the battery has insufficient charge or the
fuel level is too low, the heater will be
switched off automatically and a message
136
The car should be driven for the same time
as the heater is used to ensure that the
starter battery is recharged adequately to
replace the energy consumed by the
heater when it is used on a regular basis.
The heater is used for a maximum of 50
minutes each time.
* Option/accessory, for more information, see Introduction.
Related information
•
Engine block heater and passenger compartment heater* - messages (p. 139)
•
Additional heater* (p. 140)
04 Climate control
Engine block heater and passenger
compartment heater* - direct start
Direct start via the remote control key*
The engine block heater and passenger compartment heater can be started directly.
Direct start can be performed via:
•
•
•
information display
remote control key*
Status is also shown in the trip computer during heating.
mobile*.
Upon direct start of the engine block and
passenger compartment heater (p. 136), it will
run for 50 minutes.
Heating of the passenger compartment will
begin as soon as the engine coolant has
reached the correct temperature.
NOTE
The car can be started and driven while
the heater is running.
Direct start via the information display
1. Press OK to access the menu.
Direct start via a mobile*
Indicator lamp on remote control key with PCC*.
The engine block heater and passenger compartment heater can be activated via the
remote control key:
–
Hold the button for approach lighting
depressed for 2 seconds.
Hazard warning flashers provide information in accordance with the following:
•
5 short flashes followed by a constant
glow for approx. 3 seconds - the signal
has reached the car and the heater has
been activated.
•
5 short flashes - the signal has
reached the car but the heater has not
been activated.
•
Hazard warning flashers remain
switched off - the signal has not
reached the car.
2. Scroll with the thumbwheel to Parking
heater and select with OK.
3. Scroll forward in the next menu to Direct
start in order to activate the heater and
select with OK.
4. Exit the menu with RESET.
is depressed
If the button for information
when the heater is active then the indicator
lamp will show the status for this - at the
same time the car's lock status (p. 162) is
shown. While the status is being investigated
the indicator lamp emits a pair of short
flashes followed by a constant glow if the
heater is active.
Activation and information about the selected
settings that can be managed from a mobile
phone will be available via the Volvo On Call*
mobile app.
04
Related information
•
Engine block heater and passenger compartment heater* - timer (p. 138)
•
Engine block heater and passenger compartment heater* - immediate stop
(p. 138)
•
Engine block heater and passenger compartment heater* - messages (p. 139)
* Option/accessory, for more information, see Introduction.
137
04 Climate control
Engine block heater and passenger
compartment heater* - immediate
stop
The engine block heater and passenger compartment heater can be deactivated directly
via the information display.
1. Press OK to access the menu.
2. Scroll with the thumbwheel to Parking
heater and select with OK.
04
3. Scroll forward in the next menu to Stop in
order to deactivate the heater and select
with OK.
4. Exit the menu with RESET.
Related information
Engine block heater and passenger
compartment heater* - timer
7. Select the required minute using the
thumbwheel.
The timer of the engine block and passenger
compartment heater (p. 136) is connected to
the car's clock.
8. Press OK3 to confirm the setting.
Two different times can be selected using the
timer. Here, time refers to the time when the
car is heated and ready. The car's electronic
system calculates when heating should be
started based on the outside temperature.
NOTE
All timer programming will be cleared if the
car's clock is reset.
10. Select the other time (continue from step
2) or exit the menu with RESET.
Starting
1. Press OK to access the menu.
2. Scroll with the thumbwheel to Parking
heater and select with OK.
3. Select one of the two timers using the
thumbwheel and activate with OK.
•
Engine block heater and passenger compartment heater* - direct start (p. 137)
Adjusting
4. Exit the menu with RESET.
1. Press OK to access the menu.
•
Switching off
Engine block heater and passenger compartment heater* - timer (p. 138)
2. Scroll with the thumbwheel (p. 105) to
Parking heater and select with OK.
•
Engine block heater and passenger compartment heater* - messages (p. 139)
3. Select one of the two timers using the
thumbwheel and confirm with OK.
A timer-started heater can be switched off
manually before the set time has elapsed.
Proceed as follows:
4. Briefly press OK to move to the lit hours
setting.
5. Select the required hour using the thumbwheel.
6. Briefly press OK to move to the lit
minutes setting.
3
138
9. Go back in the menu structure using
RESET.
Press OK again to activate the timer.
* Option/accessory, for more information, see Introduction.
1. Press OK to access the menu.
2. Scroll with the thumbwheel to Parking
heater and select with OK.
> If a timer is set but not activated, a
clock icon is shown next to the set
time.
3. Select one of the two timers using the
thumbwheel and confirm with OK.
04 Climate control
4. Deactivate the timer as follows:
•
•
long press on OK or
short press on OK to continue in the
menu. Then select to stop the timer
and confirm with OK.
5. Exit the menu with RESET.
A timer-started heater can be switched off
directly (p. 137).
Related information
•
Engine block heater and passenger compartment heater* - messages (p. 139)
Engine block heater and passenger
compartment heater* - messages
Symbols and messages regarding the engine
block and passenger compartment heater
(p. 136) differ depending on whether the combined instrument panel is analogue (p. 61) or
digital (p. 62).
Symbol
Display
The heater is
switched on and
running.
The heater's timer
is activated after
the remote control
key has been
removed from the
ignition switch and
leaving the car the engine and
passenger compartment are
heated at the set
time.
When the heater has been activated
the heat symbol illuminates in the
information display.
When one of the timers is activated the symbol for activated timer illuminates in the information display at the same time as the set
time is shown next to the symbol.
Symbol for activated timer in analogue combined instrument panel.
Symbol for activated timer in digital
combined instrument panel.
The table shows symbols and display texts
that appear.
Specification
Fuel
operated
heater
stopped
Battery
saving
mode
04
The heater has
been stopped by
the car's electronics in order to
facilitate starting
the engine.
}}
* Option/accessory, for more information, see Introduction.
139
04 Climate control
||
Symbol
Display
Specification
Fuel
operated
heater
stopped
Low fuel
level
Setting the heater
is not possible due
to fuel level being
too low - this is in
order to facilitate
starting the engine
as well as
approx. 50 km
driving.
Fuel
operated
heater
Service
required
04
Heater not working. Contact a
workshop for
repair. Volvo recommends that you
contact an authorised Volvo workshop.
Additional heater*
Fuel-driven additional heater*
For cars with diesel engines sold in cold climate zones4 an additional heater may be
required to obtain the correct operating temperature in the engine and to obtain sufficient
heating in the passenger compartment.
The car is equipped with either an electric
(p. 141) or a fuel-driven additional heater
(p. 140).
In such instances, the car is equipped with
either
The heater is switched off automatically when
the correct temperature is reached or when
the engine is switched off.
•
•
electric additional heater (p. 141) or
fuel-driven additional heater (p. 140)5.
Related information
•
Engine block heater and passenger compartment heater* (p. 136)
A display text clears automatically after a time
or after one press on the indicator stalk
(p. 105) OK button.
The heater starts automatically when extra
heat is required when the engine is running.
NOTE
When the auxiliary heater is active there
may be smoke from underneath the car,
which is perfectly normal.
Auto mode or shutdown
The additional heater's automatic start
sequence can be switched off if required.
NOTE
Volvo recommends that the fuel-driven
additional heater should be switched off
for short distances.
Related information
•
Engine block heater and passenger compartment heater* - direct start (p. 137)
1. Before starting the engine: Select key
position I (p. 76).
•
Engine block heater and passenger compartment heater* - timer (p. 138)
2. Press OK to access the menu.
4
5
140
An authorised Volvo dealer has information regarding the geographical areas concerned.
For cars equipped with parking heater (p. 136).
* Option/accessory, for more information, see Introduction.
04 Climate control
3. Scroll with the thumbwheel to Additional
heater6 or Settings7 and select with OK.
4. Select one of the options ON or OFF
using the thumbwheel and confirm with
OK.
5. Exit the menu with RESET.
NOTE
The menu options are only visible in key
position I - any adjustments must therefore
be made before starting the engine.
Related information
•
6
7
Electric additional heater*
The car is equipped with either a fuel-driven
(p. 140) or an electric additional heater
(p. 140).
The heater cannot be controlled manually but
is instead activated automatically after the
engine has been started in outside temperatures below 9 °C and is switched off after the
set passenger compartment temperature has
been reached.
Related information
•
Engine block heater and passenger compartment heater* (p. 136)
04
Engine block heater and passenger compartment heater* (p. 136)
Analogue combined instrument panel.
Digital combined instrument panel.
* Option/accessory, for more information, see Introduction.
141
LOADING AND STORAGE
05 Loading and storage
Storage spaces
Overview of storage spaces in the passenger
compartment.
05
}}
143
05 Loading and storage
||
Storage compartment1 in door panel
Storage compartment, driver’s
side (p. 145)
Ticket clip
Storage compartment
Glovebox (p. 146)
Storage compartment, cup
holder (p. 145)
Cup holder* in rear seat
Storage pocket2
Storage compartment, rear seat
WARNING
05
Keep loose objects such as mobile
phones, cameras, remote controls for
accessories, etc. in the glove compartment
or other compartments. Otherwise they
may injure people in the car in the event of
sudden braking or a collision.
1
2
144
With ice scraper holder on the driver’s side.
Not applicable to textile upholstery.
* Option/accessory, for more information, see Introduction.
05 Loading and storage
Storage compartment driver’s side
Tunnel console
Tunnel console - armrest
This storage compartment (p. 143) is located
on the driver's side, to the left under the lighting panel.
The tunnel console is located between the
front seats.
The tunnel console is located between the
front seats.
When closed, the tunnel console's armrest
can be adjusted* longitudinally.
WARNING
Related information
Do not keep any sharp objects in the compartment, or objects which protrude.
•
•
Tunnel console - 12 V-sockets (p. 147)
Tunnel console - cigarette lighter and
ashtray* (p. 146)
Storage compartment (e.g. for CDs) and
USB*/AUX input under the armrest.
05
Includes cup holder for driver and passenger. (If ashtray and cigarette lighter
(p. 146) are specified, then there is a cigarette lighter in the 12 V socket (p. 147)
for the front seat and a detachable ashtray in the cup holder.)
Related information
•
•
Storage spaces (p. 143)
Tunnel console - armrest (p. 145)
* Option/accessory, for more information, see Introduction.
145
05 Loading and storage
Tunnel console - cigarette lighter and
ashtray*
A detachable ashtray is fitted in the cup
holder under the armrest. The cigarette lighter
is fitted in the 12 V socket (p. 147) for the
front seat.
The ashtray in the tunnel console (p. 145) is
detached by lifting the tray straight up.
Activate the lighter by pushing in the button.
The button pops out when the lighter is hot.
Pull out the lighter and light a cigarette on the
heated coils.
Glovebox
Glovebox - cooling
The glovebox is located on the passenger
side.
Glovebox (p. 146) can also be used as a
cooled area3.
The owner's manual and maps can be kept in
here for example. There are also holders for
pens on the inside of the lid. The glovebox
can be locked (p. 173)* using the key blade
(p. 164).
Related information
•
•
Storage spaces (p. 143)
Glovebox - cooling (p. 146)
Related information
•
Storage spaces (p. 143)
Start cooling by moving the control in
towards the passenger compartment to
the end position.
05
Switch off the cooling by moving the control forwards to the end position.
Cooling is active when the climate control
system is active (i.e. in key position II (p. 76))
or when the engine is running.
3
146
Applicable only to cars with ECC.
* Option/accessory, for more information, see Introduction.
05 Loading and storage
Inlay mats*
Vanity mirror
Tunnel console - 12 V-sockets
Inlay mats collect e.g. rubbish and slush.
Volvo supplies specially manufactured inlay
mats.
The vanity mirror is located on the rear of the
sun visor.
The electrical sockets (12 V) are located in the
tunnel console's storage compartment and
beside the cup holder4.
WARNING
Only use one inlaid mat at each seat, and
check before setting off that the mat by
the driver's seat is firmly affixed and
secured in the pins so that it does not get
caught adjacent to and under the pedals.
Related information
•
Cleaning the interior (p. 388)
Vanity mirror with lighting.
The light illuminates automatically when the
cover is lifted.
Related information
•
Lamp replacement - vanity mirror lighting
(p. 365)
12 V socket in tunnel console, front seat.
05
The electrical sockets can be used for various
accessories designed for 12 V, e.g. display
screens, music players and mobile phones.
For the sockets to supply current, the remote
control key must be in at least key position I
(p. 76).
WARNING
Always leave the plug in the socket when
the socket is not in use.
4
If ashtray and cigarette lighter are specified then there is no cup holder and adjacent 12 V socket.
}}
* Option/accessory, for more information, see Introduction.
147
05 Loading and storage
||
NOTE
Optional equipment and accessories - e.g.
display screens, music players and mobile
phones - which are connected to one of
the passenger compartment's 12V electrical sockets could be activated by the climate control system, even when the
remote control key has been removed or
when the car is locked, for example, when
the engine block and passenger compartment heater* is activated at a preset time.
For this reason remove the plugs from the
electrical sockets for optional equipment
or accessories when not in use because
the battery could be drained in the event of
such an occurrence!
Loading
Payload depends on the car's kerb weight.
Payload depends on the car's kerb weight.
The total of the weight of the passengers and
all accessories reduces the car's payload by
a corresponding weight.
For more detailed information on weights, see
Weights (p. 395).
The tailgate is opened via a button
on the lighting panel or the remote
control key, see Locking/unlocking tailgate (p. 173).
WARNING
The car’s driving properties change
depending on the weight and positioning
of the load.
IMPORTANT
05
Max. power takeoff is 10 A (120 W) in
either socket.
To bear in mind when loading
NOTE
The compressor for emergency puncture
repair (p. 331) has been tested and
approved by Volvo. For information on the
use of Volvo's recommended temporary
emergency puncture repair (TMK).
Related information
148
•
Tunnel console - cigarette lighter and
ashtray* (p. 146)
•
12 V socket - cargo area (p. 151)
•
Position the load firmly against the rear
seat's backrest.
Note that objects must not prevent the function of the WHIPS system for the front seats if
any of the rear seat's backrests is folded
down, see WHIPS - seating position (p. 38).
•
•
* Option/accessory, for more information, see Introduction.
Centre the load.
Heavy objects should be placed as low
as possible. Avoid placing heavy loads on
lowered backrests.
•
Cover sharp edges with something soft to
avoid damaging the upholstery.
•
Secure all loads to the load retaining eyelets with straps or web lashings.
WARNING
A loose object weighing 20 kg can, in a
frontal collision at a speed of 50 km/h,
carry the impact of an item weighing
1000 kg.
WARNING
The protection provided by the inflatable
curtain in the headlining may be compromised or eliminated by high loads.
•
Never load cargo above the backrest.
WARNING
Always secure the load. Always secure the
load. During heavy braking the load may
otherwise shift, causing personal injury to
the car's occupants.
Cover sharp edges and sharp corners with
something soft.
Switch off the engine and apply the parking brake when loading/unloading long
items. Otherwise you may accidentally
knock the gear lever or gear selector with
the load into a drive position - and the car
could then move off.
05 Loading and storage
Related information
•
•
•
•
Load retaining eyelets (p. 150)
Cargo net (p. 152)
Loading - long load (p. 149)
Roof load (p. 149)
Loading - long load
Roof load
To simplify loading in the cargo area, the rear
seat backrest can be folded down. The passenger seat backrest can also be folded for an
extra long load.
The load carriers recommended for roof loads
are the ones developed by Volvo. This is in
order to avoid damage to the car and in order
to achieve the maximum possible safety during a journey.
Folding the passenger seat
See (p. 78).
Lowering the rear seat backrest
See (p. 81).
Related information
•
Loading (p. 148)
Carefully follow the installation instructions
supplied with the carriers.
•
Check periodically that the load carriers
and load are properly secured. Lash the
load securely with retaining straps.
•
Distribute the load evenly over the load
carriers. Put the heaviest objects at the
bottom.
•
The size of the area exposed to the wind,
and therefore fuel consumption, increase
with the size of the load.
•
05
Drive gently. Avoid quick acceleration,
heavy braking and hard cornering.
WARNING
The car's centre of gravity and driving characteristics are altered by roof loads.
For information about the maximum permitted load on the roof, including load carriers and any space box, see Weights
(p. 395).
Related information
•
Loading (p. 148)
149
05 Loading and storage
Load retaining eyelets
Loading - bag holder
Loading - folding bag holder*
The load retaining eyelets are used to fasten
straps in order to anchor items in the cargo
area.
The bag holders keep carrier bags in place
and prevent them from overturning and
spreading their contents around the cargo
area. The holder has a capacity of max. 3 kg.
A folding bag holder in the floor keeps bags in
place and prevents them from overturning
and spreading their contents in the cargo
area, and can be opened up in three positions.
05
WARNING
Hard, sharp and/or heavy objects which
protrude may cause injury under violent
braking.
Always secure large and heavy objects
with a seatbelt or cargo retaining straps.
Bag holder
Related information
•
•
Related information
•
Loading (p. 148)
Loading (p. 148)
Loading - folding bag holder* (p. 150)
Folding bag holder
It can be set to two adjustment positions and
one service position, as it is known, where it
is fully unfolded. There are also two floor
combination variants, one with adjustment
positions in a tub under the floor and one with
adjustment positions in plastic rails. The raising below shows the adjustment position in a
tub under the floor.
The load on the central holder is max. 3 kg
and max. 10 kg on the outer holder.
150
* Option/accessory, for more information, see Introduction.
05 Loading and storage
Raising
12 V socket - cargo area
NOTE
The electrical socket can be used for various
accessories designed for 12 Volts, e.g. display screens, music players and mobile
phones.
The compressor for temporary emergency
puncture repair has been tested and
approved by Volvo. For information on the
use of Volvo's recommended temporary
emergency puncture repair (TMK), see
Emergency puncture repair* (p. 331).
Related information
•
Tunnel console - 12 V-sockets (p. 147)
Lift the handle* on the upper floor and
fold up the floor.
Move the floor forwards to an appropriate
position and place it in the adjustment
groove.
3. In service position, the floor is moved all
the way forwards towards the rear seat
back and placed in the plastic support in
the centre.
Related information
•
•
Loading (p. 148)
Loading - bag holder (p. 150)
05
Lower the cover to access the electrical
socket.
•
The socket also provides voltage when
the remote control key is not in the ignition switch.
IMPORTANT
Max. socket current is 10 A (120 W).
NOTE
Remember that using the electrical socket
with the engine switched off involves the
risk of discharging the car's battery.
* Option/accessory, for more information, see Introduction.
151
05 Loading and storage
Cargo net
A cargo net prevents cargo from being
thrown forward in the passenger compartment in the event of heavy braking.
Attaching
NOTE
The easiest way to fit the safety net is via
one of the rear doors.
WARNING
It is necessary to ensure that the upper
securing points of the safety net are fitted
correctly and that the puller-straps are
secured properly. Damaged nets must not
be used.
05
The cargo net is fitted into four mounting points.
For safety reasons, the cargo net must
always be correctly fastened and secured.
The mesh is made of a strong nylon fabric
and secured behind the front seat backrests.
WARNING
Loads in the luggage compartment must
be anchored well, and also have a correctly fitted safety net.
152
1. Unfold the cargo net and make sure that
the split upper rod is locked in the
extended position.
2. Hook one end of the rod into the roof
mounting with the anchoring strap locks
turned towards you.
3. Hook the other end of the rod into the
roof mounting on the opposite side - the
telescopic spring-loaded retaining hooks
facilitate alignment. Take care to press
forward the rod's retaining hooks for each
respective roof mounting's front end position.
05 Loading and storage
4. Hook the cargo net's anchoring straps
into the eyes on the rear of the seat slide
rails - it is easier if the backrests are
straightened and the seats are moved
forward slightly.
Removal and storage
The folded cargo net is stored in its bag in the
cargo area.
Pay attention to make sure that you do
not press the seat/backrest hard against
the net when the seat/backrest is moved
back again - only adjust until the seat/
backrest makes contact with the net.
IMPORTANT
If a seat/backrest is pushed backwards
hard into the safety net then the net and/or
its roof mounts may be damaged.
5. Tension the cargo net with the anchoring
straps.
The cargo net can be easily removed and folded
up.
Release the tension in the net by pressing
in the button on the anchoring strap's
lock and feeding out part of the strap.
Related information
•
•
Loading (p. 148)
Load retaining eyelets (p. 150)
05
Press in the catch and detach both of the
anchoring strap's hooks.
Unhook the rod from its roof mounting by
pulling back on the rod in the roof mountings' rear end position. Press the rod in
any direction so that the hook engages in
the rod, which at the same time releases
the hook on the other side.
Finally, remove the remaining roof mounting hook from the roof mounting.
4. Break the rod in the centre, fold it
together and roll up the net.
Insert the net in the storage bag.
153
05 Loading and storage
Hat shelf
The hat shelf can be removed to provide
additional cargo space.
Hat shelf removal
05
Undo the hat shelf lifting eyes on both
sides.
Unhook the front edge of the hat shelf
and remove it.
Related information
•
•
154
Loading (p. 148)
Loading - long load (p. 149)
LOCKS AND ALARM
06 Locks and alarm
Remote control key
More information
Amongst other things, the remote control key
is used for locking/unlocking and starting the
engine.
There are three variants of key available Remote control key in basic version, Remote
control key without PCC* and Remote control
key with PCC*.
Functionality
Locking/
unlocking
and detachable key
blade
06
156
x
without
PCCA
x
with
PCCB
x
Keyless
locking/
unlocking
x
x
Keyless
engine starting
x
x
Information
button and
indicator
lamps
A
B
BasicA
•
Remote Control Key Basic - is a key in
the basic version, see Remote control key
- functions (p. 160) for a description of its
functions.
•
Remote control key without PCC - with
Keyless Drive* (p. 166) and keyless locking (p. 168) and unlocking (p. 168).
•
Remote control key with PCC - also has
an information button and indicator
lamps. Read more about these unique
functions (p. 162).
All remote control keys have a detachable key
blade (p. 163) made of metal. The visible
section is available in two versions so that it
is possible to distinguish between the remote
control keys.
More remote control keys can be ordered but not variants other than the one supplied
with the car. Up to six keys can be programmed and used for one single car.
The car is supplied with two remote control
keys.
WARNING
If there are children in the car:
x
Remember to switch off the supply to the
power windows by removing the remote
control key if the driver leaves the car.
5-button key
6-button key
* Option/accessory, for more information, see Introduction.
Remote control key - losing
If you lose a remote control key (p. 156) then
a new one can be ordered at a workshop - an
authorised Volvo workshop is recommended.
The remaining remote control keys must be
taken to the Volvo workshop. The code of the
missing remote control key must be erased
from the system as a theft prevention measure. The current number of keys registered to
the car can be checked in the menu system
MY CAR. For a description of the menu system, see MY CAR (p. 108).
Related information
•
•
Remote control key - functions (p. 160)
Remote control key - range (p. 161)
06 Locks and alarm
Remote control key - personalisation*
The key memory in the remote control key
means that certain settings in the car can be
individually adapted for different people.
The key memory function is available in combination with power* driver's seat (p. 79).
Settings for door mirrors (p. 101), driver's
seat, steering force (p. 259) and the combined instrument panel's theme, contrast and
colour mode (p. 62) can be stored in the key
memory, depending on the car's equipment
level.
The function1 can be activated/deactivated in
the menu system MY CAR. For a description
of the menu system, see MY CAR (p. 108).
When the function is activated, the settings
are automatically linked to the key memory.
This means that a change in a setting will
automatically be saved in the specific remote
control key's memory.
Storing settings
Make sure that the key memory function is
activated in the menu system MY CAR.
1
2
Proceed as follows in order to store the settings and use the key memory in the remote
control key:
WARNING
Risk of crushing! Make sure that children
do not play with the controls. Check that
there are no objects in front of, behind or
under the seat during adjustment. Ensure
that none of the rear seat passengers is in
danger of becoming trapped.
1. Unlock the car with the remote control
key in whose memory the setting2 shall
be stored.
2. Make the desired settings for e.g. the
seat and the door mirrors.
Changing settings
3. The settings are stored in the current
remote control key's memory.
The next time the car is unlocked with the
same remote control key, the positions that
are stored in the key memory will be set automatically - providing that they have been
changed since the last time the current
remote control key was used.
Emergency stop
If the seat accidentally begins to move, press
one of the setting buttons for the seat or
memory buttons in order to stop the seat.
Restarting to reach the seat position stored in
the key memory is performed by pressing the
unlock button on the remote control key. The
driver's door must then be open.
If several people each with a remote control
key approach the car, then the settings for
e.g. seat and door mirrors are implemented
for the person whose remote control key
unlocks the driver's door.
If the driver's door has been opened by
person A with remote control key A, but
person B with remote control key B shall
drive, then the settings can be changed as
follows:
•
Standing by the driver's door, or sitting
behind the steering wheel, person B
presses the button for unlocking on
his/her remote control key.
•
Select one of three possible memories for
seat adjustment with seat button 1-3.
•
Adjust the seat and door mirrors manually.
Known as Car key memory in MY CAR.
This setting does not affect settings that have been stored in the power seat's memory function.
06
}}
* Option/accessory, for more information, see Introduction.
157
06 Locks and alarm
||
Related information
•
•
Remote control key - functions (p. 160)
Remote control key with PCC* - unique
functions (p. 162)
Locking/unlocking - indicator
Lock indicator
When the car is locked or unlocked using the
remote control key (p. 156) the direction indicators confirm that locking/unlocking was
correctly performed.
A flashing LED by the windscreen verifies that
the car is locked.
•
Locking - one flash and the door mirrors
are folded3 in.
•
Unlocking - two flashes and the door mirrors are folded3 out.
NOTE
Be aware of the risk of locking the remote
control key in the car.
When locking, indication is given only if all
locks have been locked and all doors are
closed. Indication is given when the last door
has been closed.
Same LED as alarm indicator (p. 179).
NOTE
Cars that are not equipped with alarm also
have this indicator.
Selecting the function
Different options for indicating locking/
unlocking with light can be set in the menu
system MY CAR. For a description of the
menu system, see MY CAR (p. 108).
06
Related information
•
•
•
3
158
Only for cars with retractable power door mirrors.
* Option/accessory, for more information, see Introduction.
Keyless drive* (p. 166)
Lock indicator (p. 158)
Alarm indicator (p. 179)
Related information
•
Locking/unlocking - indicator (p. 158)
06 Locks and alarm
Remote control key - electronic
immobiliser
The electronic immobiliser is a theft protection system that prevents the vehicle from
being started (p. 266) by an unauthorised
person.
Each remote control key (p. 156) has a unique
code. The car can only be started with the
correct remote control key with the correct
code.
The following error messages in the combined instrument panel's information display
are related to the electronic immobiliser:
Message
Specification
Insert car
key
Error when reading the
remote control key during
starting - Remove the key
from the ignition switch,
press it in again and make a
new start attempt.
Car key
not found
(Applicable
only to cars
with the
Keyless
function.)
Immobiliser Try to
start again
Error reading the remote
control key during starting Try to start again.
If the error persists: Insert
the remote control key into
the ignition switch and try to
start again.
Remote-controlled immobiliser with
tracking system
Remote-controlled immobiliser with tracking
system makes it possible to track and locate
the car, and to remotely activate the immobiliser to switch off the engine.
Contact your nearest Volvo dealer for more
information and assistance with activating the
system.
Related information
•
•
Remote control key (p. 156)
Remote control key - electronic immobiliser (p. 159)
Error in immobiliser system
during starting. If the error
persists: Contact a workshop - an authorised Volvo
workshop is recommended.
06
Related information
•
Remote-controlled immobiliser with
tracking system (p. 159)
•
Keyless drive* (p. 166)
* Option/accessory, for more information, see Introduction.
159
06 Locks and alarm
Remote control key - functions
Unlocking (p. 170) - Unlocks the doors
and tailgate while the alarm is deactivated.
The remote control key has functions such as
locking and unlocking the doors.
Press and hold to open all windows simultaneously. For more information, see Total airing function (p. 173).
Functions
The function can be changed from unlocking
all doors simultaneously, to unlocking the
driver's door only with one press of the button and, after a further press of the button within ten seconds - unlocking the remaining
doors.
Remote control key with PCC* (Personal Car
Communicator).
Remote control key in basic version.
Locking
Unlocking
06
Approach light duration
Tailgate
Panic function
Information button - see Remote control
key with PCC* - unique functions (p. 162)
for a description of its functionality.
Function buttons
Locking – Locks the doors and tailgate
while the alarm is activated, see Locking/
unlocking - from the outside (p. 170).
Press and hold to close all windows simultaneously. For more information, see Total airing function (p. 173).
WARNING
If windows are closed using the remote
control key, check that nobody's hands
are trapped.
160
* Option/accessory, for more information, see Introduction.
The function can be changed in the menu
system MY CAR. For a description of the
menu system, see MY CAR (p. 108).
Approach light duration (p. 93) - Used
to switch on the car's lighting at a distance.
Tailgate (p. 173) - Unlocks and disarms
the alarm for the tailgate only.
Panic function – Used to attract attention in an emergency.
Press and hold the button for at least three
seconds or press it twice within three seconds to activate the direction indicators and
the horn.
The function can be turned off with the same
button once it has been active for at least five
seconds. Otherwise the function switches off
automatically after approx. three minutes.
06 Locks and alarm
Related information
•
Remote control key (p. 156)
Remote control key - range
Remote control key functions (in its basic version) have a range of approx. 20 metres from
the car.
Related information
•
•
Remote control key (p. 156)
Remote control key - functions (p. 160)
If the car does not verify a button being
pressed - move closer and try again.
NOTE
The remote control key functions may be
disrupted by surrounding radio waves,
buildings, topographical conditions, etc.
The car can always be locked/unlocked
with the key blade (p. 164).
If the remote control key is removed from the
car when the engine is running or key position
I or II (p. 75) is active, and if all doors are
closed, then a warning message is shown in
the information display in the combined
instrument panel and an audio reminder signal sounds at the same time.
06
The message is extinguished and the audible
reminder signal stops when the remote control key is brought back to the car after
either/or:
•
The remote control key has been inserted
in the ignition switch.
•
•
Speed exceeds 30 km/h.
The OK button has been pressed.
161
06 Locks and alarm
Remote control key with PCC* unique functions
Using the information button
–
Press the information button
A remote control key with PCC* has
enhanced functionality compared with a
remote control key in basic version (p. 156) in
the form of an information button and indicator lamps.
.
> All indicator lamps flash for approximately 7 seconds and the light travels
around on the PCC. This indicates that
information from the car has been
read.
If any of the other buttons are pressed
during this time then the reading is
interrupted.
NOTE
Green continuous light – the car is
locked.
If none of the indicator lamps illuminates with repeated use of the information
button and in different locations (as well as
after 7 seconds and after the light has
travelled around on the PCC), contact a
workshop - an authorised Volvo workshop
is recommended.
Yellow continuous light – the car is
unlocked.
Red continuous light – the alarm has
been triggered since the car was locked.
Red light flashing alternately in both indicator lamps – The alarm was triggered
less than 5 minutes ago.
Remote control key with PCC.
06
Information button
Indicator lamps
Indicator lamps display information in accordance with the following illustration:
Using the information button enables access
to certain information from the car via the
indicator lamps.
162
* Option/accessory, for more information, see Introduction.
Related information
•
Remote control key with PCC* - range
(p. 163)
06 Locks and alarm
Remote control key with PCC* - range
The range of a remote control key with PCC
(Personal Car Communicator) for unlocking
the doors and tailgate is approx. 20 metres
from the car - the other functions are up to
approx. 100 metres. If the car does not verify
a button being pressed - move closer and try
again.
NOTE
The information button function may be
disrupted by surrounding radio waves,
buildings, topographical conditions, etc.
Related information
•
•
Keyless Drive* - range (p. 166)
Remote control key - range (p. 161)
Detachable key blade
The remote control key contains a detachable
key blade of metal with which some functions
can be activated and some operations carried
out.
The key blade's unique code is provided by
authorised Volvo workshops, which are recommended when ordering new key blades.
Key blade functions
Using the remote control key's detachable
key blade:
•
the left-hand front door can be opened
manually (p. 164) if central locking cannot be activated with the remote control
key.
•
the rear doors' mechanical child safety
locks can be activated/deactivated
(p. 176).
•
the right-hand front door and the rear
doors can be locked manually, e.g. in the
event of power failure.
•
•
the glovebox lock* opens.
Out of range
If the remote control key is too far away from
the car for the information to be read then the
status the car was last left in is shown, without the light travelling around on the remote
control key.
If several remote control keys are used for the
car then it is only the remote control key last
used for locking/unlocking that shows the
correct status.
NOTE
If none of the indicator lamps illuminates with repeated use of the information
button and in different locations (as well as
after 7 seconds and after the light has
travelled around on the PCC), contact a
workshop - an authorised Volvo workshop
is recommended.
06
the airbag for front passenger seat
(PACOS*) can be activated/deactivated.
Related information
•
•
•
Manual locking of the door (p. 171)
Locking/unlocking - glovebox (p. 173)
Passenger airbag - activating/deactivating* (p. 33)
* Option/accessory, for more information, see Introduction.
163
06 Locks and alarm
Detachable key blade - detaching/
attaching
Detaching/attaching the detachable key blade
(p. 163) is carried out as follows:
Removing the key blade
Related information
•
Detachable key blade - unlocking doors
(p. 164)
•
Child safety locks - manual activation
(p. 176)
•
Passenger airbag - activating/deactivating* (p. 33)
Detachable key blade - unlocking
doors
The detachable key blade can be used if the
central locking cannot be activated with the
remote control key - e.g. if the remote control
key's battery (p. 165) has been discharged.
The left-hand front door can be opened as
follows:
1. Unlock the left-hand front door with the
key blade in the door handle's lock cylinder. For more information, see Keyless
Drive* - unlocking with the key blade
(p. 169).
NOTE
When the door has been unlocked using
the key blade and is opened, the alarm is
triggered.
Slide the spring-loaded catch to the side.
06
At the same time pull the key blade
straight out backwards.
Attaching the key blade
Carefully refit the key blade into its location in
the remote control key (p. 156).
1. Hold the remote control key with the slot
pointed up and lower the key blade into
its slot.
2. Lightly press the key blade. You should
hear a "click" when the key blade is
locked in.
164
* Option/accessory, for more information, see Introduction.
2. Deactivate the alarm by inserting the
remote control key in the ignition switch.
For a car with Keyless Drive, see Keyless
Drive* - unlocking with the key blade (p. 169).
Related information
•
•
Detachable key blade (p. 163)
Remote control key (p. 156)
06 Locks and alarm
Remote control key/PCC - replacing
the battery
NOTE
Turn the remote control key over with the
buttons facing up, this is to avoid the batteries falling out when it is opened.
The battery5 in the remote control key may
need to be replaced.
The battery for the remote control key should
be replaced if:
•
IMPORTANT
the information symbol is illuminated and
the display in the combined instrument
panel shows Low battery in remote
control. Please change batteries.
Avoid touching new batteries and their
contact surfaces with your fingers as this
may impair their function.
Battery replacement
and/or
•
the locks repeatedly do not react to signals from the remote control key within
20 metres from the car.
NOTE
Opening
Slide the spring-loaded catch to the
side.
At the same time pull the key blade
straight out backwards.
Insert a 3 mm slot screwdriver in the
hole behind the spring-loaded catch and
gently prize the remote control key up.
5
Remote control key with PCC has two batteries.
Volvo recommends that the batteries to be
used in the remote control key/PCC fulfil
UN Manual of Test and Criteria, Part III,
sub-section 38.3. Batteries fitted in the
factory or replaced by an authorised Volvo
workshop fulfil the above criteria.
Closely study how the battery/batteries
are secured on the inside of the cover,
with regard to their (+) and (–) sides.
06
Remote control key with one battery
1. Carefully prize out the battery.
2. Install a new one with the (+) side down.
}}
165
06 Locks and alarm
||
Remote control key with PCC* with two
batteries
1. Carefully prize out the batteries.
2. First install one new one with the (+) side
up.
3. Position the white plastic tab in between
and finally install a second new battery
with the (+) side down.
Battery type
Use batteries with designation CR2430, 3 V.
Assembly
1. Press the remote control key together.
2. Hold the remote control key with the slot
pointed up and lower the key blade into
its slot.
3. Lightly press the key blade. You should
hear a "click" when the key blade is
locked in.
06
IMPORTANT
Make sure that exhausted batteries are
disposed of in a manner which is kind to
the environment.
Keyless drive*
Keyless Drive* - range8
Cars equipped with Keyless Drive have a starting and locking system that can be operated
keylessly.
In order to unlock the doors or tailgate automatically without pressing a button on the
remote control key, a remote control key must
be within approx. 1.5 metres from the car's
door handle or tailgate.
With the keyless starting and locking system
the car can be started, locked and unlocked
without the remote control key (p. 156)
inserted in the ignition switch6. It is enough to
have the remote control key with you in a
pocket. The system makes it easier and more
convenient to e.g. open the car when your
hands are full.
Both of the remote control keys included with
the car have Keyless functionality. It is possible to order more remote control keys.
The car's electrical system can be set to
three different levels - key position 0, I and II
(p. 76) - with the remote control key.
Related information
•
•
•
Related information
•
•
6
8
166
The person who wishes to lock or unlock a
door must have the remote control key with
him or her. It is not possible to lock or unlock
a door if the remote control key is on the
opposite side of the car.
Remote control key (p. 156)
Remote control key - functions (p. 160)
Does not apply to Remote Control Key Basic.
Does not apply to cars with keyless start
* Option/accessory, for more information, see Introduction.
Keyless Drive* - range (p. 166)
Keyless Drive* - secure handling of the
remote control key (p. 167)
Keyless Drive* - interference to remote
control key function (p. 167)
The red rings in the above figure indicate the
range covered by the system's antennas.
If all remote control keys are removed from
the car when the engine is running or key
position I or II (p. 76) is active, and if a door
has been opened and then closed, then a
06 Locks and alarm
warning message is shown in the information
display in the combined instrument panel and
an audio reminder signal sounds at the same
time.
When the remote control key has been
returned to the car, the warning message
goes off and the audible reminder ceases
once either/or:
•
•
a door has been opened and closed
•
The OK button on the direction indicator
stalk.
the remote control key has been inserted
in the ignition switch
Keyless Drive* - secure handling of
the remote control key
Keyless Drive* - interference to
remote control key function
It is important to handle all remote control
keys with great care.
Electromagnetic fields and screening can
interfere with the remote control key's Keyless
functions (p. 166).
If one of the remote control keys9 has been
left in the car then the Keyless functionality is
deactivated in case the car is e.g. locked with
the other remote control key that belongs to
the car. This prevents unauthorised entry.
The next time the car is unlocked with the
other remote control key the forgotten remote
control key is reactivated again.
IMPORTANT
Related information
•
•
Keyless drive* (p. 166)
Avoid leaving the remote control key with
PCC behind in the car. If someone breaks
into your car and takes the remote control
key, it will e.g. be possible to start the car
by pressing the remote control key in the
ignition switch and then pressing the
START/STOP ENGINE button.
Keyless Drive* - antenna location (p. 170)
NOTE
Do not place/store the remote control key
with keyless function near a mobile phone
or metal object - no closer than 10-15 cm.
If interference is experienced nonetheless,
use the remote control key and the key blade
like a remote control key in basic version
(p. 156).
Related information
•
Remote control key/PCC - replacing the
battery (p. 165)
•
Keyless Drive* - secure handling of the
remote control key (p. 167)
•
Keyless Drive* - range (p. 166)
06
Related information
•
9
Keyless drive* (p. 166)
Applies to remote control key with PCC (Personal Car Communicator).
* Option/accessory, for more information, see Introduction.
167
06 Locks and alarm
Keyless Drive* - locking
Cars equipped with Keyless Drive have a
touch-sensitive area on the outer handle of
the doors and a rubberised button next to the
tailgate's rubberised pressure plate.
Related information
•
•
Keyless drive* (p. 166)
Alarm indicator (p. 179)
Keyless Drive* - unlocking11
Unlocking takes place when a hand grasps a
door handle or the tailgate's rubberised pressure plate is actuated - open the door or tailgate as normal.
NOTE
The door handles normally register a hand
that takes hold of the handle, but with
thick gloves on or after a very quick hand
movement a second attempt may be
required, or with the glove taken off.
Related information
•
•
06
Lock the doors and the tailgate by grasping
one of the door handles or pressing the
smaller of the tailgate's two rubberised buttons - the lock indicator (p. 158) in the windscreen confirms that locking has been completed by starting to flash.
All doors and the tailgate must be closed
before the car can be locked - otherwise the
car is not locked.
NOTE
In cars with automatic gearbox selectors,
the gear selector must be set to the P
position; otherwise the car can be neither
locked nor alarmed.
168
* Option/accessory, for more information, see Introduction.
Keyless drive* (p. 166)
Keyless Drive* - locking (p. 168)
06 Locks and alarm
Keyless Drive* - unlocking with the
key blade
If central locking cannot be activated with the
remote control key, e.g. if the batteries are
discharged, then the left-hand front door can
be opened using the remote control key's
detachable key blade (p. 163).
1. Press the key blade approx. 1 cm straight
up into the hole on the underside of the
door handle/cover - do not prize.
> The plastic cover loosens automatically by means of the torque when the
blade is pushed straight up and into
the opening.
2. Then insert the key blade in the lock cylinder and unlock the door.
3. Refit the plastic cover after unlocking.
Keyless Drive* - lock settings
Lock settings for cars equipped with Keyless
Drive can be adapted by indicating in the
menu system MY CAR which doors are to be
unlocked.
For a description of the menu system, see
MY CAR (p. 108).
Related information
•
Keyless drive* (p. 166)
NOTE
When the left-hand front door is unlocked
using the key blade and is opened, this
triggers the alarm (p. 178). It is switched
off by inserting the remote control key in
the ignition switch, see Alarm - remote
control key not working (p. 180).
Hole for key blade - to loosen the cover.
To access the lock cylinder, the door handle's
plastic cover must be removed - this is also
done with the key blade:
11
Related information
•
•
Keyless drive* (p. 166)
Detachable key blade - detaching/attaching (p. 164)
06
Does not apply to remote control key with keyless start.
* Option/accessory, for more information, see Introduction.
169
06 Locks and alarm
Keyless Drive* - antenna location
WARNING
Cars equipped with Keyless Drive have a
number of built-in antennas positioned at different locations in the car.
People with pacemaker operations should
not come closer than 22 cm to the keyless
system's antennae with their pacemaker.
This is to prevent interference between the
pacemaker and the keyless system.
Related information
•
Rear bumper, centre
Door handle, left rear
06
Cargo area, central and furthest in under
the floor
Door handle, right rear
Centre console, under the rear section
Centre console, under the front section.
Keyless drive* (p. 166)
Locking/unlocking - from the outside
Locking/unlocking from the outside is carried
out using the remote control key (p. 160). The
remote control key can lock/unlock all doors,
the tailgate and the fuel filler flap. Different
sequences for unlocking can be selected.
In order that the lock sequence can be activated, the driver's door must be closed - if
any of the other doors or the tailgate is open,
then it/they is/are locked and the alarm is
activated only when it/they are closed. For
cars equipped with keyless locking system*
all doors and the tailgate must be closed, see
Keyless Drive* - locking (p. 168) and Keyless
Drive* - unlocking (p. 168).
NOTE
Be aware of the risk of locking the remote
control key in the car.
If it is not possible to lock/unlock with the
remote control key, the battery may be discharged - lock or unlock the left-hand front
door with the detachable key blade (p. 164).
NOTE
Remember that the alarm is triggered
when the door is opened after being
unlocked with the key blade - the alarm is
switched off when the remote control key
is inserted into the ignition switch.
170
* Option/accessory, for more information, see Introduction.
06 Locks and alarm
WARNING
Be aware of the risk of being locked in the
car when it is locked from the outside
using the remote control key - it is then not
possible to open any of the doors from the
inside with the door controls. For more
information, see Deadlocks* (p. 175).
Automatic relocking
If none of the doors or the tailgate is opened
within two minutes of unlocking, all are
locked again automatically. This function prevents the car from being left unlocked unintentionally. For cars with alarm, see Alarm
(p. 178).
Manual locking of the door
The door can be opened from both the
outside and the inside.
In certain situations the car must be lockable
manually, e.g. in the event of power failure.
The left-hand front door can be locked with
its lock cylinder and the remote control key's
detachable key blade (p. 169).
Other doors have no lock cylinders and
instead have a lock switch on the end of each
door which must be depressed using the key
blade - they are then mechanically locked/
blocked to prevent them being opened from
outside. The doors can still be opened from
the inside.
The door is blocked against opening from
the outside. To return to position A, the
inner door handle must be opened.
The doors can also be unlocked with the
unlock button on the remote control key
(p. 156) or with the central locking button on
the driver's door.
NOTE
Related information
•
Locking/unlocking - from the inside
(p. 172)
•
Remote control key - functions (p. 160)
•
A door's lock reset only locks that particular door - not all doors simultaneously.
•
A manually locked rear door with activated manual child safety locks
(p. 176) cannot be opened from either
the outside or the inside. A rear door
that is locked in this way can only be
unlocked with the remote control key
or central locking button.
06
Related information
•
Remote control key/PCC - replacing the
battery (p. 165)
Manual locking of the door. Not to be mixed up
with child safety locks (p. 176).
–
Remove the detachable key blade
(p. 164) from the remote control key.
Insert the key blade in the hole for lock
reset and press the key in until the key
bottoms, approx. 12 mm.
* Option/accessory, for more information, see Introduction.
171
06 Locks and alarm
Locking/unlocking - from the inside
Locking/unlocking can be performed using
the driver's door button for central locking. All
doors and tailgate (p. 173) can be locked or
unlocked simultaneously.
With central locking button on both front
doors and electric lock button in each rear
door:
•
Illuminated lamp means that only that
particular door is locked. When all buttons are illuminated all doors are locked.
Unlocking
A door can be unlocked from the inside in
two different ways:
•
Press the central locking button
.
A long press also opens all the side windows*
simultaneously (see also section Total airing
function (p. 173)).
•
Central locking
•
06
Press one side
the other side
of the button to lock to unlock.
With central locking button only in the driver's
door, other doors have no button:
•
172
Locking
•
Lamp in lock button
When the lamp in the central locking button
for the driver's door is illuminated it means
that all doors are locked.
Illuminated lamp means that all doors are
locked.
Pull the door handle and open the door the door is unlocked and opened in one
operation.
Both front doors must be closed for the
central locking to be activated. Press the
central locking button
- all doors are
locked. If any of the rear doors is open, it
will lock when it is closed.
A long press also closes all the side windows
simultaneously (see also section Total airing
function (p. 173)).
Automatic locking
The doors and tailgate are locked automatically when the car starts to move.
* Option/accessory, for more information, see Introduction.
The function can be activated/deactivated in
the menu system MY CAR. For a description
of the menu system, see MY CAR (p. 108).
Related information
•
Locking/unlocking - from the outside
(p. 170)
•
Alarm (p. 178)
06 Locks and alarm
Total airing function
Locking/unlocking - glovebox
Locking/unlocking - tailgate
The total airing function opens or closes all
side windows simultaneously and can be
used for example to quickly air the car during
hot weather.
The glovebox (p. 146) can only be locked/
unlocked using the detachable key blade from
the remote control key (p. 156).
The tailgate can be opened, locked and
unlocked in a number of different ways.
For information on the key blade, see Detachable key blade - detaching/attaching (p. 164).
Rubber plate with electrical contact.
Central locking button
A long press on the
symbol in the central
locking button opens all side windows simultaneously. The same procedure on the
button closes all side windows simultaneously.
Locking the glovebox:
Related information
•
Locking/unlocking - from the inside
(p. 172)
•
Power windows (p. 99)
Manual opening
The tailgate is held closed by an electrical
lock. To open:
Insert the key blade in the glovebox lock
cylinder.
1. Push down gently on the wider of the two
rubberised pressure plates under the
outer handle - the lock is released.
Turn the key blade 90 degrees clockwise.
The keyhole is horizontal in the locked
position.
2. Lift the outside handle in order to fully
open the tailgate.
06
Pull out the key blade.
•
Unlock by carrying this out in reverse
order.
Related information
•
Remote control key - functions (p. 160)
}}
173
06 Locks and alarm
||
IMPORTANT
The doors remain locked and armed.
•
Minimal force is required to release the
rear hatch lock - just gently press the
rubberised panel.
The tailgate can be opened in two different
ways using the remote control key:
•
Do not place the lift force on the rubber panel when opening the rear hatch
- lift the handle. Using too much force
may damage the electrical contacts on
the rubber panel.
Unlocking with the remote control key
One press - The boot lid is unlocked, but
remains closed - press lightly on the rubberised pressure plate under the outer handle
and lift the boot lid. If the tailgate is not
opened within 2 minutes then it is relocked
and the alarm is re-armed.
Two presses - The boot lid is unlocked and
the lock is disengaged at which the boot lid
opens about a centimetre - lift the outer handle to open. Rain, cold, frost or snow could
however prevent the tailgate from disengaging from the lock.
NOTE
•
06
Using the remote control key (p. 156)
button the alarm for the tailgate can be disarmed* and the tailgate unlocked on its own.
•
The lock indicator (p. 158) on the instrument
panel stops flashing in order to show that not
all of the car is locked and the alarm's* level
and movement sensors and the sensors for
opening the tailgate are disconnected.
174
Opening the car from inside
* Option/accessory, for more information, see Introduction.
When the boot lid/tailgate is unlocked
with 2 presses or from the car interior,
automatic relocking does not take
place because the boot lid/tailgate is
open - it must be closed manually.
After the boot lid/tailgate has been
closed it is unlocked and the alarm is
not armed - relock it and re-arm the
alarm with the remote control key's
lock button
.
Unlocking, tailgate
To open the tailgate:
–
Press the lighting panel button (1).
> The lock releases and the tailgate
opens by a few centimetres.
Locking with the remote control key
–
Press the remote control key (p. 160) but.
ton for locking
> The lock indicator on the instrument
panel starts flashing, which means that
the car is locked and the alarm* has
been activated.
Related information
•
Locking/unlocking - from the inside
(p. 172)
•
Locking/unlocking - from the outside
(p. 170)
06 Locks and alarm
Locking/unlocking - fuel filler flap
Deadlocks*
The fuel filler flap is unlocked with the remote
control key (p. 156) button for unlocking
).
(
Deadlocks12
The fuel filler flap remains unlocked until the
car is locked with the remote control key's
). If the car is locked
button for locking (
while driving or with the interior buttons then
the fuel filler flap remains unlocked.
The deadlocks are activated with the remote
control key (p. 156) and are set after an
approx. ten seconds delay after the doors
have been locked.
The fuel filler flap's locking logic also follows
the locking or unlocking of the Keyless system and the central locking system.
Temporary deactivation
means that all door handles are
mechanically disengaged, which prevents
doors being opened from the inside.
NOTE
If a door is opened within the delay time
then the sequence is interrupted and the
alarm is deactivated.
Active menu options are indicated with a cross.
Related information
•
•
Fuel filler flap - Opening/closing (p. 294)
Fuel filler flap - manual opening (p. 294)
MY CAR
The car can only be unlocked with the remote
control key when the deadlocks function is
activated. The front left door can also be
unlocked with the detachable key blade
(p. 163).
WARNING
Do not allow anyone to remain in the car
without first deactivating the deadlocks in
order to avoid the risk of anyone being
locked in.
OK MENU
TUNE knob control
EXIT
If someone is going to stay in the car but the
doors must be locked from the outside, then
the deadlocks function can be temporarily
switched off, which is carried out in the menu
system MY CAR. For a detailed description of
the menu system, see MY CAR (p. 108).
06
In MY CAR one of the following options can
be selected:
• Activate once: - The combined instrument panel then shows Locks and
alarm Reduced guard and deadlocks
12
Only in combination with alarm.
}}
* Option/accessory, for more information, see Introduction.
175
06 Locks and alarm
||
are switched off when the car is locked,
only at this time. (Note that the alarm's
movement and tilt detectors* are
switched off at the same time.)
During the next time the engine is started, the
system is reset to zero and the combined
instrument panel shows the message Locks
and alarm Full guard at which the deadlocks and the alarm's movement and tilt
detectors are re-engaged.
NOTE
•
Remember that the alarm is activated
when the car is locked.
•
If any of the doors are opened from
the inside then the alarm is triggered.
Related information
•
Keyless Drive* - unlocking with the key
blade (p. 169)
Child safety locks - manual activation
The child safety locks prevent children from
being able to open a rear door from the
inside.
The child safety locks are located on the trailing edge of the rear doors and are only accessible when the doors are open.
Activate/deactivate child safety locks
• Ask on exit: - Each time the engine is
switched off, the driver must answer the
question Activate Reduced Guard until
engine has started again?.
If the deadlocks function shall be switched
off
–
06
Press OK/MENU and lock the car. (Note
that the alarm's movement and tilt detectors* are switched off at the same time.)
> The next time the engine is started, the
system is reset to zero and the combined instrument panel shows the
message Locks and alarm Full
guard at which the deadlocks function
and the alarm's movement and tilt
detectors are re-engaged.
If the locking system shall not be changed
–
176
Press EXIT and lock the car.
* Option/accessory, for more information, see Introduction.
Manual child safety locks. Not to be mixed up
with manual door lock (p. 171).
–
Use the remote control key's detachable
key blade (p. 164) to turn the knob.
The door is blocked against opening from
the inside.
The door can be opened from both the
outside and the inside.
06 Locks and alarm
NOTE
•
A door's knob control only blocks that
particular door - not both rear doors
simultaneously.
•
Cars with an electric child safety lock
do not have a manual child lock.
Related information
•
Child safety locks - electrical activation*
(p. 177)
•
Locking/unlocking - from the inside
(p. 172)
Child safety locks - electrical
activation*
The child safety locks prevent children from
being able to open a rear door from the
inside.
Activation
The electrical child safety locks can be activated/deactivated in all key positions (p. 75)
higher than 0. Activation/deactivation can be
performed up to 2 minutes after switching off
the engine, provided that no door is opened.
2. Press the button in the driver's door control panel.
> The information display shows the
message Rear child lock activated
and the button's lamp illuminates - the
locks are active.
When the electric child safety lock is active
then the rear:
•
windows can only be opened with the
driver's door control panel
•
doors cannot be opened from inside.
The current setting is stored when the engine
is switched off - if the child safety locks are
activated at engine shutdown, the function
will remain activated the next time the engine
is started.
Related information
•
Child safety locks - manual activation
(p. 176)
•
Locking/unlocking - from the inside
(p. 172)
06
Control panel driver's door.
1. Start the engine or choose a key position
higher than 0.
* Option/accessory, for more information, see Introduction.
177
06 Locks and alarm
Alarm
NOTE
The alarm is a device that warns in the event
of e.g. a break-in in the car.
The movement sensors trigger an alarm in
the event of movement in the passenger
compartment - air currents are also registered. For this reason the alarm is triggered if the car is left with a window open
or if the passenger compartment heater is
used.
Activated alarm is triggered if:
•
a door, the bonnet or the tailgate is
opened
•
a movement is detected in the passenger
compartment (if fitted with a movement
detector*)
•
the car is raised or towed away (if fitted
with a tilt detector*)
•
•
the battery's cable is disconnected
To avoid this: Close the window when
leaving the car. If the car's integrated passenger compartment heater (or a portable
electric heater) shall be used - direct the
airflow from the air vents so that they are
not pointing upwards in the passenger
compartment. Alternatively, reduced alarm
level can be used, Reduced alarm level
(p. 180).
the siren is disconnected.
If there is a fault in the alarm system then the
information display in the combined instrument panel shows a message. In which case,
contact a workshop - an authorised Volvo
workshop is recommended.
NOTE
Do not attempt to repair or alter components in the alarm system yourself. Any
such attempts may affect the terms of the
insurance.
06
Arming the alarm
–
Press the remote control key lock button.
Deactivate the alarm
–
178
* Option/accessory, for more information, see Introduction.
Press the remote control key unlock button.
Deactivating a triggered alarm
–
Press the remote control key unlock button or insert the remote control key in the
ignition switch.
Related information
•
•
Alarm - automatic re-arming (p. 179)
Alarm - remote control key not working
(p. 180)
06 Locks and alarm
Alarm indicator
Alarm - automatic re-arming
Alarm - automatic arming
The alarm indicator shows alarm system
(p. 178) status.
Automatic re-arming of the alarm (p. 178) prevents the car being left with the alarm disarmed unintentionally.
In certain countries the alarm (p. 178) is activated after a certain delay if the driver's door
was opened and closed but the car was not
re-locked.
If the car is unlocked with the remote control
key (p. 156)(and the alarm is disarmed) but
none of the doors or the tailgate is opened
within 2 minutes, then the alarm is automatically re-armed. The car is relocked at the
same time.
Related information
•
Alarm signals (p. 180)
Related information
•
Alarm - automatic arming (p. 179)
Same LED as lock indicator (p. 158).
A red LED on the instrument panel indicates
the alarm system's status:
•
•
LED not lit – Alarm not armed
•
The LED flashes rapidly after disarming
the alarm (and until the remote control
key is inserted in the ignition switch and
key position I is selected) – Alarm has
been triggered.
The LED flashes once every other second
– Alarm is armed
06
179
06 Locks and alarm
Alarm - remote control key not
working
If the alarm (p. 178) cannot be deactivated
with the remote control key, e.g. if the key's
battery (p. 165) is discharged - the car can be
unlocked, disarmed and the engine started as
follows:
1. Open the left-hand front door with the
detachable key blade (p. 169).
> The alarm is triggered, the direction
indicators flash and the siren sounds.
Alarm signals
Reduced alarm level
When the alarm (p. 178) is triggered a siren
sounds and all direction indicators flash.
Reduced guard means that the movement
and tilt detectors can be temporarily deactivated.
•
A siren sounds for 30 seconds or until the
alarm is switched off. The siren has its
own battery and works independently of
the car battery.
•
The direction indicators flash for 5
minutes or until the alarm is switched off.
To avoid accidental triggering of the alarm e.g. if a dog is left in a locked car or during
transport on a car train or car ferry - temporarily deactivate the movement and tilt detectors.
The procedure is the same as with the temporary disengaging of deadlocks, see Deadlocks* (p. 175).
Related information
•
•
06
2. Insert the remote control key in the ignition switch.
> The alarm is deactivated.
180
* Option/accessory, for more information, see Introduction.
Alarm (p. 178)
Alarm indicator (p. 179)
06 Locks and alarm
Type approval - remote control key
system
Type approval for the remote control key system can be read in the table.
Country/Area
China
Lock system, standard
Country/Area
EU, China
Keyless lock system (Keyless drive)
Country/Area
Hong Kong
Related information
•
Remote control key (p. 156)
EU
06
Korea
181
DRIVER SUPPORT
07 Driver support
Electronic stability control (ESC) general
Stability system ESC (Electronic Stability
Control) helps the driver to avoid skidding and
improves the car's traction.
The activation of the ESC system
during braking may be noticed as a
throbbing sound. The car may
accelerate slower than expected
when the accelerator pedal is depressed.
WARNING
The stability system ESC is supplementary
assistance - it cannot handle all situations
in all road conditions.
The driver always bears responsibility that
the vehicle is driven safely and that applicable road traffic rules and regulations are
followed.
The ESC system consists of the following
functions:
•
•
•
•
•
•
•
1
Active Yaw Control
Spin Control
Traction control system
Engine drag control - EDC
Corner Traction Control - CTC
Driver Steering Recommendation – DSR
Active Yaw Control
Driver Steering Recommendation – DSR
The function checks the driving and brake
force of the wheels individually in order to
stabilise the car.
DSR (Driver Steering Recommendation) helps
the driver steer the car in the right direction
when there is reduced traction or when the
ABS system engages.
Spin Control
The function reduces engine power if the
drive wheels slip against the underlying surface in order to maintain stability and traction.
Traction control system
The function is active at low speed and transfers power from the driving wheel that is spinning to the one that is not.
Engine drag control - EDC
EDC (Engine Drag Control) prevents involuntary wheel locking, e.g. after shifting down or
engine braking when driving in low gears on
slippery road surfaces.
Involuntary wheel locking while driving can,
amongst other things, impair the driver's ability to steer the car.
The primary role of the DSR function is to
help the driver steer in the right direction
when the car is skidding.
DSR engages by applying slight torque to the
steering wheel in the direction in which the
car should be steered to maintain/achieve
maximum possible traction and stabilise the
car.
Trailer Stability Assist* - TSA1
Trailer stability assist (p. 307) function is to
stabilise the car and trailer combination if it
begins to snake. For more information, see
Driving with a trailer (p. 300).
NOTE
The function is deactivated if the driver
selects Sport mode.
Corner Traction Control - CTC
CTC (Corner Traction Control) compensates
for understeer and allows higher than normal
acceleration in a bend without wheelspin on
the inner wheel, e.g. on an arcing motorway
entrance road to quickly reach the prevailing
traffic speed.
Related information
•
Electronic stability control (ESC) - operation (p. 184)
•
Electronic stability control (ESC) - symbols and messages (p. 185)
07
Trailer Stability Assist* - TSA
Trailer Stability Assist is included in the installation of the Volvo genuine towbar.
* Option/accessory, for more information, see Introduction.
183
07 Driver support
Electronic stability control (ESC) operation
Selection of level - Sport mode
The ESC system is always activated - it cannot be deactivated.
However, the driver can
select the Sport mode,
which allows for a more
active driving experience.
In Sport mode the system
detects whether the accelerator pedal, steering wheel movements and
cornering are more active than in normal driving and then allows controlled skidding with
the rear section up to a certain level before it
intervenes and stabilises the car.
If the driver stops a controlled skid by releasing the accelerator pedal, for example, then
the ESC system intervenes and stabilises the
car.
07
With Sport mode, maximum traction is also
obtained if the car has become stuck, or
when driving on a loose surface - e.g. sand or
deep snow.
Proceed as follows to select Sport mode:
Sport mode is selected in the menu system
MY CAR. For a description of the menu system, see MY CAR (p. 108).
184
Sport mode is indicated in the combined instrument panel by means of
this symbol illuminating with a constant glow until the driver deselects
the function or until the engine is switched off
- after the next time the engine is started the
ESC system is back in its normal mode once
again.
Related information
•
Electronic stability control (ESC) - general
(p. 183)
•
Electronic stability control (ESC) - symbols and messages (p. 185)
•
MY CAR (p. 108)
07 Driver support
Electronic stability control (ESC) symbols and messages
Table
Symbol
Message
Specification
ESC Temporarily OFF
ESC system has been temporarily reduced due to excessive brake disc temperature - the function is
reactivated automatically when the brakes have cooled.
ESC Service required
ESC system disengaged.
•
•
Stop the car in a safe place, switch off the engine and start it again.
Visit a workshop if the message remains - an authorised Volvo workshop is recommended.
"Message"
There is a message in the combined instrument panel - read it!
Constant glow for
2 seconds.
System check when the engine is started.
Flashing light.
ESC system is being activated.
Constant glow.
Sport mode is activated.
and
07
NOTE: The ESC system is not deactivated in this mode - it is partially reduced.
}}
185
07 Driver support
||
Related information
07
186
•
Electronic stability control (ESC) - general
(p. 183)
•
Electronic stability control (ESC) - operation (p. 184)
07 Driver support
Road Sign Information (RSI)
Road sign information (RSI)* operation
WARNING
The road sign information function (RSI –
Road Sign Information) helps the driver to
remember which road signs the car has
passed.
RSI does not work in all situations but is
designed merely as a supplementary aid.
The driver always bears ultimate responsibility for ensuring that the vehicle is driven
safely and that applicable road traffic rules
and regulations are followed.
The road sign information function (RSI –
Road Sign Information) helps the driver to
remember which road signs the car has
passed. How the function is operated is
described below.
Related information
•
Road sign information (RSI)* - operation
(p. 187)
•
Road sign information (RSI)* - limitations
(p. 189)
Examples of readable speed related2 signs.
The road sign information function gives
information on current speed, that a motorway or road is starting/ending and when
overtaking is prohibited. If both a sign for
motorway/road for motorised traffic and a
sign showing the maximum permitted speed
are passed, RSI decides to show the sign
symbol for maximum permitted speed.
2
3
Recorded speed information3.
When RSI has recorded a road sign with an
imposed speed, the combined instrument
panel displays the sign as a symbol.
Together with the symbol for
the current speed limit, a
sign showing that overtaking
is prohibited may also be
displayed where appropriate.
Road signs shown in the combined instrument panel are market-dependent - the illustrations only show a few examples.
Road signs shown in the combined instrument panel are market-dependent - the illustrations only show a few examples.
07
}}
* Option/accessory, for more information, see Introduction.
187
07 Driver support
||
End of restriction or motorway
Additional signs
A corresponding road sign is shown in the
combined instrument panel for
approx. 10 seconds in situations where RSI
detects a sign that involves the end of a
speed limit - or other speed-related information, e.g. end of a motorway.
Examples of such signs are:
Display of additional information
End of all restrictions.
Examples of additional signs3.
End of motorway.
Following which, the sign information is hidden until the next speed-related sign is
detected.
07
Sometimes different speed limits are signposted for the same road - an additional sign
then indicates the circumstances under which
the different speeds apply. The road section
may be particularly susceptible to accidents
in rain and/or fog, for example.
188
A symbol for additional sign
in the form of an empty
frame under the combined
instrument panel's speed
symbol means that the RSI
has detected an additional
sign with supplementary
information for the current speed limit.
Road sign information On/Off
An additional sign relating to rain is displayed
only if the windscreen wipers are in use.
The speed applicable on an
exit is indicated in certain
markets by means of an
additional sign containing an
arrow.
Speed signs linked to this
type of additional sign are displayed only if
the driver is using the direction indicator.
3
Some speeds are applicable
only after e.g. a specific distance or at a certain time of
day. The driver's attention is
drawn to the situation by
means of a symbol for an
additional sign under the
symbol showing speed.
Road signs shown in the combined instrument panel are market-dependent - the illustrations only show a few examples.
The combined instrument panel's speed symbol display can be disabled.
07 Driver support
To deactivate the RSI function:
•
Search for the function in the menu system MY CAR MY CAR (p. 108), uncheck
Road sign information and back out
with EXIT.
Speed Alert On/Off
Road sign information (RSI)* limitations
Speed limiter*
The road sign information function (RSI –
Road Sign Information) helps the driver to
remember which road signs the car has
passed. The function has the following limitations.
A (Speed Limiter) can be regarded as a
reverse cruise control - the driver regulates
the speed using the accelerator pedal but is
prevented from accidentally exceeding a preselected/set speed by the speed limiter.
The RSI function's camera sensor has limitations just like the human eye. Find out more
about this in the section on the camera sensor limitations (p. 230).
Signs which indirectly provide information on
a prevailing speed limit, e.g. name signs for
towns/districts, are not recorded by the RSI
function.
The driver can opt to receive a warning when
the applicable speed limit is exceeded by
5 km/h or more. This warning is given by the
symbol showing the applicable maximum
speed temporarily flashing when this speed is
exceeded.
To activate speed warning:
•
Search for the function in the menu system MY CAR MY CAR (p. 108), check
Speed alert and back out with EXIT.
Related information
•
•
•
Road Sign Information (RSI) (p. 187)
Here are some other examples of what can
disrupt the function:
•
•
•
•
•
Steering wheel keypad and combined instrument
panel Digital and Analogue.
Faded signs
Signs positioned on bends
Speed limiter - On/Off.
Rotated or damaged signs
Concealed or poorly positioned signs
Signs completely or partly covered with
frost, snow and/or dirt.
Standby mode
Activate and adjust the max. speed.
Related information
•
•
Standby mode ceases and the stored
speed is resumed.
Road Sign Information (RSI) (p. 187)
Road sign information (RSI)* - operation
(p. 187)
07
Selected speed
Speed limiter active
Road sign information (RSI)* - limitations
(p. 189)
MY CAR (p. 108)
}}
* Option/accessory, for more information, see Introduction.
189
07 Driver support
||
Related information
•
•
Speed limiter* - getting started (p. 190)
Speed limiter - temporary deactivation
and standby mode* (p. 191)
•
Speed limiter* - alarm for speed exceeded (p. 192)
•
Speed limiter* - deactivation (p. 193)
Speed limiter* - getting started
Switch on and activate
A (Speed Limiter) can be regarded as a
reverse cruise control - the driver regulates
the speed using the accelerator pedal but is
prevented from accidentally exceeding a preselected/set speed by the speed limiter.
When the speed limiter is active,
its symbol (6) is shown in combination with a
mark (5) by the set maximum speed in the
combined instrument panel.
Selection and storage of the highest possible
speed in the memory can be made both during a journey and while stationary.
While driving
1. Press the steering wheel button
to
switch on the speed limiter.
> The symbol (6) for speed limiter illuminates in the combined instrument
panel.
Steering wheel keypad and combined instrument
panel Digital and Analogue.
Speed limiter - On/Off.
Standby mode ceases and the stored
speed is resumed.
Standby mode
07
Activate and adjust the max. speed.
Selected speed
Speed limiter active
190
* Option/accessory, for more information, see Introduction.
2. When the car is moving at the desired
highest possible speed: Press one of the
steering wheel buttons
or
until the
combined instrument panel shows a
mark (5) next to the desired maximum
speed.
> The speed limiter is then active and the
selected max. speed is stored in the
memory.
When stationary
1. Press the steering wheel button
switch on the speed limiter.
to
07 Driver support
Speed limiter* - changing speed
2. Scroll with the
button until the combined instrument panel shows a mark (5)
by the desired maximum speed.
> The speed limiter is then active and the
selected max. speed is stored in the
memory.
To adjust +/- 5 km/h:
Related information
•
•
Speed limiter* (p. 189)
Speed limiter - temporary
deactivation and standby mode*
Changing the stored speed
Stored maximum speed is changed with
or
button.
short or long presses on the
Use short presses - each press gives
+/- 5 km/h.
A (Speed Limiter) can be regarded as a
reverse cruise control - the driver regulates
the speed using the accelerator pedal but is
prevented from accidentally exceeding a preselected/set speed by the speed limiter.
To adjust +/- 1 km/h:
•
Hold the button depressed and release
when the combined instrument panel's
mark is by the desired maximum speed.
Last press made is stored in the memory.
Related information
•
Speed limiter* (p. 189)
Steering wheel keypad and instrument panel Digital and Analogue.
Speed limiter - On/Off.
Standby mode ceases and the stored
speed is resumed.
Standby mode
07
Activate and adjust the max. speed.
Selected speed
Speed limiter active
}}
* Option/accessory, for more information, see Introduction.
191
07 Driver support
||
Temporary deactivation - standby mode
–
To temporarily deactivate the speed limiter
and set it in standby mode:
–
Press
.
> The combined instrument panel's
mark (5) changes colour from GREEN
to WHITE (Digital) or from WHITE to
GREY (Analogue) and the driver can
temporarily exceed the set maximum
speed.
The speed limiter is automatically reactivated after the accelerator pedal is
released and the car's speed is slowed
down to below the selected/stored
maximum speed - the mark (5)
changes colour from WHITE to GREEN
(Digital) or GREY to WHITE (Analogue)
and the car's maximum speed is again
limited.
The speed limiter is reactivated with
. The mark (5) then
one press on
changes colour from WHITE to GREEN
(Digital) or GREY to WHITE (Analogue)
and the car's maximum speed is limited again.
Temporary deactivation with the
accelerator pedal
The speed limiter can also be set in standby
mode with the accelerator pedal, e.g. for rapidly accelerating the car out of a situation:
Depress the accelerator pedal fully.
> The combined instrument panel shows
the stored maximum speed with a coloured mark (5) and the driver can temporarily exceed the set maximum
speed – the mark (5) changes colour
from GREEN to WHITE (Digital) or
WHITE to GREY (Analogue) during that
time.
Speed limiter* - alarm for speed
exceeded
A (Speed Limiter) can be regarded as a
reverse cruise control - the driver regulates
the speed using the accelerator pedal but is
prevented from accidentally exceeding a
pre-selected/set speed by the speed limiter.
On steep roads the speed limiter's engine
braking effect may be inadequate and the
selected maximum speed is exceeded. The
driver is alerted about this with an acoustic
signal. The signal is active until the driver has
slowed to below the selected maximum
speed.
NOTE
The alarm is only activated after 5 seconds
if the speed has been exceeded by at least
3 km/h provided that none of the buttons
or
has been depressed during the
last half minute.
Related information
•
Speed limiter* (p. 189)
Related information
•
07
192
* Option/accessory, for more information, see Introduction.
Speed limiter* (p. 189)
07 Driver support
Speed limiter* - deactivation
Cruise control*
A (Speed Limiter) can be regarded as a
reverse cruise control - the driver regulates
the speed using the accelerator pedal but is
prevented from accidentally exceeding a preselected/set speed by the speed limiter.
The cruise control (CC – Cruise Control) helps
the driver maintain an even speed, resulting in
more relaxing driving on motorways and long,
straight roads with regular traffic flows.
To deactivate the speed limiter:
–
Press the steering wheel button
Overview
.
> The combined instrument panel's
(p. 189) symbol for the speed limiter
and the mark for the set speed are
extinguished. The selected and stored
speed are thus deleted from the memory and cannot be resumed with the
button.
The driver can then use the accelerator
pedal to choose a speed without limitation.
Related information
•
The steering wheel buttons and combined instrument panel in cars with speed limiter4.
Cruise control - On/Off.
Standby mode ceases and the stored
speed is resumed.
The steering wheel buttons and combined instrument panel in cars without speed limiter4.
Speed limiter* (p. 189)
Standby mode
Activate and adjust the speed.
Selected speed (GREY = Standby mode).
Cruise control active - WHITE symbol
(GREY = Standby mode).
07
4
A Volvo dealer has updated information about what applies in each respective market.
}}
* Option/accessory, for more information, see Introduction.
193
07 Driver support
||
WARNING
The driver must always be observant with
regard to the traffic conditions and intervene when the cruise control is not maintaining a suitable speed and/or suitable
distance.
Cruise control* - managing speed
It is possible to activate, set and change the
stored speed.
Activating and setting the speed
The driver always bears ultimate responsibility for ensuring that the vehicle is driven
safely.
Related information
•
Cruise control* - managing speed
(p. 194)
•
Cruise control* temporary deactivation
and standby mode (p. 195)
•
Cruise control* - resume set speed
(p. 196)
•
•
Cruise control* - deactivate (p. 197)
The steering wheel buttons and display in cars
with speed limiter5.
To enable cruise control:
•
Press the steering wheel button for
CRUISE (without speed limiter) or
(with speed limiter).
>
The cruise control symbol (6) in the combined instrument panel illuminates Cruise control is in standby mode.
The steering wheel buttons and display in cars
without speed limiter5.
Adaptive cruise control (ACC)* (p. 198)
To activate cruise control:
07
5
194
A Volvo dealer has updated information about what applies in each respective market.
* Option/accessory, for more information, see Introduction.
•
At the required speed - press the steering
wheel button
or
.
>
The current speed is stored in the memory and the combined instrument panel's
marking (5) illuminates at the selected
speed and the symbol (6) changes from
GREY to WHITE - the car then follows the
stored speed.
07 Driver support
NOTE
Cruise Control cannot be enabled at
speeds below 30 km/h.
Cruise control* temporary
deactivation and standby mode
Temporary deactivation - standby mode
The function can be temporarily deactivated
and set in standby mode.
Changing the stored speed
Stored speed is changed by pressing button
or
:
•
Short presses give +/- 5 km/h.
or
•
Hold down the button and release it at
the required speed.
If speed is increased using the accelerator
pedal prior to pressing the
/
button,
then it is the car's current speed when the
button is pressed that is stored. Last press
made is stored in the memory.
The steering wheel buttons and display in cars
without speed limiter6.
A temporary increase in speed with the accelerator pedal, e.g. during overtaking, does not
affect the cruise control setting - the car
returns to the last stored speed when the
accelerator pedal is released.
NOTE
If any of the Cruise Control buttons are
held depressed for several minutes then it
is blocked and deactivated. To be able to
reactivate Cruise Control, the car must be
stopped and the engine restarted.
Related information
•
07
The steering wheel buttons and display in cars
with speed limiter6.
To temporarily disengage cruise control and
set it in standby mode:
•
Press
.
Cruise control* (p. 193)
}}
* Option/accessory, for more information, see Introduction.
195
07 Driver support
||
> The combined instrument panel's
marking (5) and symbol (6) change colour
from WHITE to GREY - Cruise control is
temporarily disengaged.
Standby mode due to driver intervention
Cruise control is temporarily disengaged and
set automatically in standby mode if:
•
•
•
the foot brake is used
•
the driver maintains speed higher than
the stored speed for longer than
1 minute.
Related information
•
•
•
•
Cruise control* (p. 193)
Cruise control* - managing speed (p. 194)
Cruise control* - resume set speed
(p. 196)
Cruise control* - deactivate (p. 197)
Cruise control* - resume set speed
The cruise control (p. 193) (CC – Cruise
Control) helps the driver to maintain an even
speed.
After temporary deactivation and standby
mode (p. 195) it is possible to resume the set
speed.
the clutch pedal is depressed
the gear lever/selector is moved to N
position
The driver must then regulate the speed.
A temporary increase in speed with the accelerator pedal, e.g. during overtaking, does not
affect the setting - the car returns to the last
stored speed when the accelerator pedal is
released.
Automatic standby mode
07
Cruise control is temporarily disengaged and
set in standby mode if:
•
•
•
wheels lose traction
engine speed is too low/high
speed falls below approx. 30 km/h.
The driver must then regulate the speed.
6
7
196
A Volvo dealer has updated information about what applies in each respective market.
A Volvo dealer has updated information about what applies in each respective market.
* Option/accessory, for more information, see Introduction.
The steering wheel buttons and display in cars
without speed limiter7.
07 Driver support
•
Cruise control* temporary deactivation
and standby mode (p. 195)
•
Cruise control* - deactivate (p. 197)
Cruise control* - deactivate
How it is deactivated is described here.
The steering wheel buttons and display in cars
with speed limiter7.
To reactivate the cruise control from standby
mode:
•
Press the steering wheel button
>
The combined instrument panel's
marking (5) and symbol (6) change colour
from GREY to WHITE - the car then follows the last stored speed.
.
The steering wheel buttons and display in cars
without speed limiter8.
NOTE
A marked speed increase may occur once
the speed has been resumed by selecting
.
07
Related information
•
•
7
8
Cruise control* (p. 193)
Cruise control* - managing speed (p. 194)
The steering wheel buttons and display in cars
with speed limiter8.
A Volvo dealer has updated information about what applies in each respective market.
A Volvo dealer has updated information about what applies in each respective market.
}}
* Option/accessory, for more information, see Introduction.
197
07 Driver support
||
The cruise control is switched off with the
steering wheel button (1) or by switching off
the engine - the stored speed is deleted from
the memory and cannot be resumed with the
button.
Related information
•
•
•
•
Cruise control* (p. 193)
Cruise control* - managing speed (p. 194)
Cruise control* temporary deactivation
and standby mode (p. 195)
Cruise control* - resume set speed
(p. 196)
Adaptive cruise control (ACC)*
The adaptive cruise control (ACC – Adaptive
Cruise Control) helps the driver to maintain an
even speed combined with a pre-selected
time interval to the vehicle ahead.
The adaptive cruise control provides a more
relaxing driving experience on long journeys
on motorways and long straight main roads in
smooth traffic flows.
The driver sets the desired speed (p. 202)
and time interval to the car in front. When the
radar detector detects a slower vehicle in
front of the car, the speed is automatically
adapted to that. When the road is clear again
the car returns to the selected speed.
If the adaptive cruise control is switched off
or set to standby mode and the car comes
too close to a vehicle in front, then the driver
is warned instead by a Distance Alert (p. 213)
about the short distance.
The adaptive cruise control cannot handle
all traffic, weather and road conditions.
Read all the sections about the adaptive
cruise control in the owner's manual in
order to learn about its limitations, of
which the driver should be aware before it
is used.
The driver always bears responsibility for
maintaining the correct distance and
speed, even when the adaptive cruise control is being used.
IMPORTANT
Maintenance of adaptive cruise control
components must only be performed at a
workshop - an authorised Volvo workshop
is recommended.
Automatic gearbox
07
198
WARNING
The driver must always be observant with
regard to the traffic conditions and intervene when the adaptive cruise control is
not maintaining a suitable speed or suitable distance.
Cars with automatic gearbox have enhanced
functionality with the adaptive cruise control's
Queue assistance (p. 205) function.
* Option/accessory, for more information, see Introduction.
07 Driver support
Related information
•
Adaptive cruise control* - function
(p. 199)
•
Adaptive cruise control* - overview
(p. 201)
•
Adaptive cruise control* - managing
speed (p. 202)
•
Adaptive cruise control* - set time interval
(p. 203)
•
Adaptive cruise control* - temporary
deactivation, and standby mode (p. 203)
•
Adaptive cruise control* - overtaking
another vehicle (p. 204)
•
Adaptive cruise control* - deactivate
(p. 205)
•
Adaptive Cruise Control* - queue assistance (p. 205)
•
Adaptive cruise control* - switch cruise
control functionality (p. 207)
•
•
•
Radar sensor (p. 208)
•
Adaptive cruise control* - symbols and
messages (p. 211)
9
Radar sensor - limitations (p. 208)
Adaptive cruise control* - function
WARNING
Adaptive cruise control is not a collision
avoidance system. The driver must intervene if the system does not detect a vehicle in front.
The adaptive cruise control does not brake
for humans or animals, and not for small
vehicles such as bicycles and motorcycles. Nor for oncoming, slow or stationary
vehicles and objects.
Function overview9.
Warning lamp - braking by driver required
Steering wheel (p. 82) keypad
Radar sensor (p. 208)
Adaptive cruise control consists of a cruise
control system and a coordinated spacing
system.
Adaptive cruise control* - fault tracing
and action (p. 210)
Do not use the adaptive cruise control, for
example, in city traffic, in dense traffic, at
junctions, on slippery surfaces, with a lot
of water or slush on the road, in heavy
rain/snow, in poor visibility, on winding
roads or on slip roads.
The distance to the vehicle ahead is mainly
measured by a radar sensor. The cruise control function regulates the speed with acceleration and braking. It is normal for the brakes
to emit a low sound when they are being
used by the adaptive cruise control.
WARNING
The brake pedal moves when the adaptive
cruise control brakes. Do not rest your foot
beneath the brake pedal - it may then
become trapped.
NOTE: The illustration is schematic - details may differ depending on car model.
07
}}
* Option/accessory, for more information, see Introduction.
199
07 Driver support
||
The adaptive cruise control aims to follow the
vehicle ahead in the same lane according to
what the driver set for time interval (p. 203). If
the radar sensor cannot see any vehicle in
front then the car will instead maintain the
speed set and stored by the driver. This also
takes place if the speed of the vehicle in front
exceeds the stored speed.
The adaptive cruise control aims to control
the speed in a smooth way. In situations that
demand sudden braking the driver must
brake himself/herself. This applies with large
differences in speed, or if the vehicle in front
brakes heavily. Due to limitations in the radar
sensor (p. 208) braking may come unexpectedly or not at all.
The adaptive cruise control can be activated
to follow another vehicle at speeds from
30 km/h10 up to 200 km/h. If the speed falls
below 30 km/h or if the engine speed
becomes too low, the cruise control is set in
standby mode at which automatic braking
ceases - the driver must then take over himself/herself to maintain a safe distance to the
vehicle ahead.
07
Warning lamp - braking by driver
required
WARNING
The adaptive cruise control only warns of
vehicles which the radar sensor has
detected. Hence the warning may not be
given, or it may be given with a certain
delay. Do not wait for a warning without
braking when so required.
Steep roads and/or heavy load
1. Collision warning system warning lamp and
warning sound11.
If the car needs to be braked more heavily
than the adaptive cruise control capacity and
the driver does not brake, then the warning
lamp and warning sound from the Collision
warning system (p. 223) are used in order to
alert the driver that immediate intervention is
required.
NOTE
The warning lamp may be difficult to see in
strong sunlight or when wearing sunglasses.
Adaptive cruise control has a braking
capacity that is equivalent to more than 40%
of the car's braking capacity.
10
11
200
Queue Assist (p. 205) in cars with automatic gearbox can operate in the range of 0-200 km/h.
NOTE: The illustration is schematic - details may vary depending on car model.
* Option/accessory, for more information, see Introduction.
Bear in mind that the adaptive cruise control
is primarily intended for use when driving on
level road surfaces. It may have difficulty in
keeping the correct distance from the vehicle
ahead when driving on steep downhill slopes,
with a heavy load or with a trailer - in which
case, be extra attentive and ready to slow
down.
Related information
•
•
•
Adaptive cruise control (ACC)* (p. 198)
Adaptive cruise control* - overview
(p. 201)
Cruise control* (p. 193)
07 Driver support
Adaptive cruise control* - overview
Operation of the adaptive cruise control
(p. 198) and steering wheel keypad varies
depending on whether or not the car is equipped with speed limiter (p. 189)12.
Adaptive cruise control with Speed
limiter
Cruise control - On/Off.
Time distance
ACC is active at the GREEN symbol
(WHITE = standby mode).
ACC is active at the GREEN symbol
(WHITE = standby mode).
Adaptive cruise control without Speed
limiter
Related information
•
•
Adaptive cruise control (ACC)* (p. 198)
Adaptive cruise control* - managing
speed (p. 202)
•
Adaptive cruise control* - set time interval
(p. 203)
•
Adaptive cruise control* - temporary
deactivation, and standby mode (p. 203)
•
Cruise control* (p. 193)
Standby mode ceases and the stored
speed is resumed.
Cruise control - On/Off or Standby mode.
Standby mode ceases and the stored
speed is resumed.
Time interval - Increase/decrease.
Standby mode
Activate and adjust the speed.
Time interval - Increase/decrease.
(Not used)
Activate and adjust the speed.
Green marking at stored speed (WHITE =
standby mode).
Green marking at stored speed (WHITE =
standby mode).
12
Time distance
07
A Volvo dealer has updated information about what applies in each respective market.
* Option/accessory, for more information, see Introduction.
201
07 Driver support
Adaptive cruise control* - managing
speed
At the same time a speed
range is marked:
stored speed when the accelerator pedal is
released.
To switch on ACC:
•
Press the steering wheel button
-a
similar WHITE symbol illuminates in the
combined instrument panel (8) which
shows that the adaptive cruise control is
in standby mode (p. 203).
To activate ACC:
•
At the required speed - press the steering
or
.
wheel button
>
The current speed is stored in the memory, the combined instrument panel
shows a "magnifying glass" (6) around
the stored speed for a second or so and
its marking changes from WHITE to
GREEN.
When this symbol changes colour
from WHITE to GREEN, ACC is
active and the car maintains the
stored speed.
07
Only when the symbol shows
an image of another vehicle
is the distance to the vehicle
in front controlled by ACC.
NOTE
•
the higher speed with GREEN marking is
the pre-programmed speed
•
the lower speed is the speed of the vehicle in front.
In certain situations it cannot be reactivated - in which case, the combined instrument panel (p. 211) shows Adaptive
cruise control unavailable.
Changing the stored speed
Stored speed is changed with short or long
or
button.
presses on the
To adjust +/- 5 km/h:
•
Use short presses - each press gives
+/- 5 km/h.
To adjust +/- 1 km/h:
•
Hold the button depressed and release
when the combined instrument panel's
mark is by the desired speed.
Last press made is stored in the memory.
If speed is increased using the accelerator
/
button,
pedal prior to pressing the
then it is the car's current speed when the
button is pressed that is stored.
A temporary increase in speed with the accelerator pedal, e.g. during overtaking, does not
affect the setting - the car returns to the last
202
If any of the adaptive cruise control buttons are held depressed for several
minutes then the function is blocked and
deactivated. To be able to reactivate it, the
car must be stopped and the engine
restarted.
* Option/accessory, for more information, see Introduction.
Related information
•
•
•
Adaptive cruise control (ACC)* (p. 198)
Adaptive cruise control* - overview
(p. 201)
Cruise control* (p. 193)
07 Driver support
Adaptive cruise control* - set time
interval
Different time intervals to the
vehicle in front can be
selected and shown in the
combined instrument panel
as 1-5 horizontal lines - the
more lines the longer the
time interval. One line corresponds to approximately 1 second to the
vehicle in front, 5 lines
approximately 3 seconds.
To set/change the time distance:
•
Adaptive cruise control* - temporary
deactivation, and standby mode
NOTE
Only use the time intervals permitted by
local traffic regulations.
The adaptive cruise control can be temporarily deactivated and set in standby mode.
If the adaptive cruise control does not
appear to react when activated, this may
be because the time distance to the vehicle in front is preventing an increase in
speed.
Temporary deactivation/standby mode with speed limiter
The higher the speed the longer the calculated distance in metres for a given time
interval.
To temporarily disengage adaptive cruise
control and set it in standby mode:
•
This symbol and stored speed marking then changes colour from
GREEN to WHITE.
Read more how speed is handled (p. 202).
Related information
Turn the steering wheel button set's
thumbwheel (or use the
/
buttons for
cars without Speed limiters).
•
•
At low speed, when the distances are short,
the adaptive cruise control increases the time
interval slightly.
•
Press the steering wheel button
Adaptive cruise control (ACC)* (p. 198)
Temporary deactivation/standby mode without speed limiter
Adaptive cruise control* - overview
(p. 201)
To temporarily disengage adaptive cruise
control and set it in standby mode:
Cruise control* (p. 193)
•
The adaptive cruise control allows the time
interval to vary noticeably in certain situations
in order to allow the car to follow the vehicle
in front smoothly and comfortably.
Note that a short time interval only allows the
driver a short time to react and take action if
any unforeseen traffic problem should arise.
Press the steering wheel button
Standby mode due to driver intervention
The adaptive cruise control is temporarily disengaged and set automatically in standby
mode if:
•
•
the foot brake is used
the clutch pedal is depressed for longer
than 1 minute13
07
The same symbol is also shown when Distance Alert (p. 213) is activated.
13
Disengaging and selecting a higher or lower gear does not involve standby mode.
}}
* Option/accessory, for more information, see Introduction.
203
07 Driver support
||
•
•
the gear selector is moved to N position
(automatic gearbox)
the driver maintains speed higher than
the stored speed for longer than
1 minute.
The driver must then regulate the speed.
A temporary increase in speed with the accelerator pedal, e.g. during overtaking, does not
affect the setting - the car returns to the last
stored speed when the accelerator pedal is
released.
For more information, see the sections Managing speed (p. 202) and Overtaking another
vehicle (p. 204).
Automatic standby mode
•
•
•
•
•
07
speed has fallen below 30
14
204
Adaptive cruise control* - overtaking
another vehicle
wheels lose traction
ACC can also assist during overtaking.
brake temperature is high
When the car is following another vehicle and
the driver indicates an impending overtaking
manoeuvre with the direction indicator15, the
adaptive cruise control helps to briefly accelerate the car towards the vehicle in front.
the radar sensor is covered e.g. by wet
snow or heavy rain (radar waves blocked).
Resume set speed
Adaptive cruise control in standby mode is
reactivated with one press on the steering
- the speed is then set to the
wheel button
last stored speed.
This function is active at speeds
above 70 km/h.
Read more about the different time intervals
(p. 203) to the vehicle in front.
Read more about how you manage the speed
(p. 202).
NOTE
WARNING
A marked speed increase may occur once
the speed has been resumed by selecting
.
Be aware that this function can be activated in more situations other than during
overtaking, e.g. when a direction indicator
is used to indicate a change of lane or exit
to another road - the car will then accelerate briefly.
Related information
•
•
•
Adaptive cruise control (ACC)* (p. 198)
Adaptive cruise control* - overview
(p. 201)
Cruise control* (p. 193)
An automatic deactivation can be due to:
•
•
km/h14
For more information on symbols, messages
and their meaning, see section Symbols and
messages in the display (p. 211).
The adaptive cruise control is dependent on
other systems, e.g. Stability system ESC
(p. 183). If any of these systems stops working, the adaptive cruise control is deactivated
automatically.
In the event of automatic deactivation a signal
will sound and the message Adaptive cruise
control cancelled is shown in the combined
instrument panel. The driver must then intervene and adapt the speed and distance to
the vehicle ahead.
engine speed is too low/high
the driver opens the door
the driver takes off his seatbelt
Does not apply to a car with Queue Assist - it can go all the way down to 0 km/h.
* Option/accessory, for more information, see Introduction.
Related information
•
•
•
Adaptive cruise control (ACC)* (p. 198)
Adaptive cruise control* - overview
(p. 201)
Cruise control* (p. 193)
07 Driver support
Adaptive cruise control* - deactivate
Keypad with Speed limiter
The adaptive cruise control is disengaged
with a short press of the steering wheel but. The set speed is cleared and cannot
ton
button.
be resumed with the
Keypad without Speed limiter
A short press on the steering wheel button
sets the adaptive cruise control in standby
mode. With a further short press it is deactivated. The set speed is cleared and cannot
button.
be resumed with the
Related information
•
•
•
Adaptive cruise control (ACC)* (p. 198)
Adaptive cruise control* - overview
(p. 201)
Cruise control* (p. 193)
Adaptive Cruise Control* - queue
assistance
Extended speed range
NOTE
Queue assistance also provides the adaptive
cruise control with enhanced functionality at
speeds lower than 30 km/h.
In cars with automatic gearbox the adaptive
cruise control is supplemented with the
queue assistance function (also referred to as
"Queue Assist").
Queue assistance has the following functions:
•
•
•
In order to activate the cruise control the
driver's door must be closed and the driver
must be wearing the seatbelt.
With an automatic gearbox, the adaptive
cruise control can follow another vehicle
within the range 0-200 km/h.
NOTE
Extended speed range - also at lower
than 30 km/h and at stationary
Activation of the cruise control below
30 km/h requires a vehicle in front within a
reasonable distance.
Change of target
Automatic braking ceases when stationary
Note that the lowest programmable speed for
the adaptive cruise control is 30 km/h - even
though the cruise control is capable of following another vehicle down to a standstill, a
lower speed cannot be selected.
Learn more about how you manage the
speed (p. 198) and different time intervals to
the vehicle in front (p. 203).
For shorter stops in connection with inching
in slow traffic or at traffic lights driving is
automatically resumed if the stops do not
exceed approx. 3 seconds - if it takes longer
before the car in front starts moving again
then the cruise control is set in standby mode
(p. 203) with automatic braking. The driver
must then reactivate it in one of the following
ways:
•
Press the steering wheel button
.
07
or
15
•
Depress the accelerator pedal.
>
The cruise control will then resume following the vehicle in front.
On left flash only in left-hand-drive car, or right flash in right-hand-drive car.
}}
* Option/accessory, for more information, see Introduction.
205
07 Driver support
||
NOTE
WARNING
Queue Assist can keep the car stationary
for a maximum of 4 minutes - then the
brakes release.
When the adaptive cruise control is following a vehicle ahead at speeds in excess of
30 km/h and the target is changed from a
vehicle ahead to a stationary vehicle, the
cruise control will ignore the stationary
vehicle and instead select the stored
speed.
See more information under the header
below, "Cessation of automatic braking
when stationary".
•
Change of target
fore intervene and brake the car himself in
order to maintain its position.
IMPORTANT
Queue Assist can keep the car stationary
for a maximum of 4 minutes - then the
brakes release.
The driver's attention is drawn to this over
several stages, with increasing intensity:
The driver must intervene him/herself
and brake.
1. Acoustic alarm (pinging) and text message.
Automatic standby mode with change
of target
2. A warning lamp in the windscreen also
starts to flash.
The adaptive cruise control is disengaged
and set in standby mode:
If the target vehicle in front suddenly turns then
there may be stationary traffic in front.
07
When the adaptive cruise control is following
another vehicle at speeds lower than
30 km/h and changes target from a moving to
a stationary vehicle, the cruise control will
slow down for the stationary vehicle.
•
when the speed is below 5 km/h and
cruise control is not sure whether the target object is a stationary vehicle or some
other object, e.g. a speed bump.
•
when the speed is below 5 km/h and the
vehicle in front turns off so the cruise
control no longer has a vehicle to follow.
Queue assistance releases the foot brake and
is set to standby mode in these situations as
well:
•
the driver puts his/her foot on the brake
pedal
In the following situations, queue assistance
stops automatic braking at a standstill:
•
the gear selector is moved to P, N or R
position
•
•
•
the driver sets the cruise control in
standby mode
•
the parking brake is applied.
Termination of automatic braking at a
standstill
the driver opens the door
the driver takes off his seatbelt.
This means that the brakes are released and
the car will start to roll - the driver must there-
206
3. "Stabbing" braking occurs.
For more information on symbols, messages and their meaning, see the section
Symbols and messages in the display (p. 211).
07 Driver support
Related information
•
•
•
Adaptive cruise control (ACC)* (p. 198)
Adaptive cruise control* - overview
(p. 201)
Cruise control* (p. 193)
Adaptive cruise control* - switch
cruise control functionality
Changing back from CC to ACC
Changing from ACC to CC
A symbol for active cruise control is shown in
the combined instrument panel:
CC
ACC
Cruise Control
Adaptive Cruise
Control
Cruise control
Switch off the cruise control (CC) with 1-2
button. The next time the
presses on the
system is switched on it is the adaptive cruise
control (ACC) that is activated.
Related information
•
•
Adaptive cruise control
Adaptive cruise control (ACC)* (p. 198)
Adaptive cruise control* - overview
(p. 201)
•
Adaptive cruise control* - temporary
deactivation, and standby mode (p. 203)
•
Cruise control* (p. 193)
With one press of the button the adaptive element (spacing system) in the adaptive cruise
control (p. 198) is deactivated, at which point
the car only follows the set/stored speed.
•
Hold down the steering wheel button
- the combined instrument panel's symto
.
bol changes from
>
This activates Cruise Control CC.
WARNING
07
The car no longer brakes automatically
after switching from ACC to CC - it merely
follows the set speed.
* Option/accessory, for more information, see Introduction.
207
07 Driver support
Radar sensor
Radar sensor - limitations
The function of the radar sensor is to detect
cars or larger vehicles in the same direction,
in the same lane.
A radar sensor (p. 208) has certain limitations
- due to its limited field of vision for example.
The radar sensor is used by the following
functions:
•
•
•
Distance Warning*
Adaptive cruise control*
Collision Warning with Auto Brake and
Pedestrian Detection*
The capacity of the adaptive cruise control to
detect a vehicle in front is significantly
reduced if:
•
the speed of vehicles in front is significantly different from your own speed
•
its radar sensor becomes blocked - e.g.
in heavy rain or slush, or if other objects
have collected in front of the radar sensor.
IMPORTANT
In the event of visible damage to the car's
grille, or if you suspect that the radar sensor may be damaged:
• Contact a workshop - an authorised
Volvo workshop is recommended.
The function may completely or partially
disappear - or malfunction - if the grille,
the radar sensor or its bracket is damaged
or has loosened.
07
NOTE
Keep the surface in front of the radar sensor clean.
Field of vision
The radar sensor has a limited field of vision.
In some situations another vehicle is not
detected, or the detection is made later than
expected.
Modification of the radar sensor could result
in it being illegal to use.
Related information
•
•
•
•
208
Radar sensor - limitations (p. 208)
Adaptive cruise control (ACC)* (p. 198)
Collision warning system* (p. 223)
Distance Warning* (p. 213)
* Option/accessory, for more information, see Introduction.
ACC field of vision.
Sometimes the radar sensor is late at
detecting vehicles at close distances e.g. a vehicle that drives in between the
car and vehicles in front.
Small vehicles, such as motorcycles, or
vehicles not driving in the centre of the
lane can remain undetected.
In bends the radar sensor may detect the
wrong vehicle or lose a detected vehicle
from view.
07 Driver support
WARNING
WARNING
The driver must always be observant with
regard to the traffic conditions and intervene when the adaptive cruise control is
not maintaining a suitable speed or suitable distance.
Adaptive cruise control is not a collision
avoidance system. The driver must intervene if the system does not detect a vehicle in front.
The adaptive cruise control does not brake
for humans or animals, and not for small
vehicles such as bicycles and motorcycles. Nor for oncoming, slow or stationary
vehicles and objects.
The adaptive cruise control cannot handle
all traffic, weather and road conditions.
Read all the sections about the adaptive
cruise control in the owner's manual in
order to learn about its limitations, of
which the driver should be aware before it
is used.
Do not use the adaptive cruise control, for
example, in city traffic, in dense traffic, at
junctions, on slippery surfaces, with a lot
of water or slush on the road, in heavy
rain/snow, in poor visibility, on winding
roads or on slip roads.
The driver always bears responsibility for
maintaining the correct distance and
speed, even when the adaptive cruise control is being used.
WARNING
Accessories or other objects such as auxiliary lamps must not be fitted in front of the
grille.
Related information
•
•
•
Adaptive cruise control (ACC)* (p. 198)
Collision warning system* (p. 223)
Distance Warning* (p. 213)
07
* Option/accessory, for more information, see Introduction.
209
07 Driver support
Adaptive cruise control* - fault tracing
and action
If the combined instrument panel shows the
message Radar blocked See manual then it
means that the adaptive cruise control's radar
sensor (p. 208) cannot detect other vehicles
in front of the car.
sion Warning with Auto Brake (p. 223) are
working.
This message indicates that neither of the
functions for Distance Alert (p. 213) or Colli-
The following table presents examples of
possible causes for a message being shown
along with the appropriate action:
Cause
Action
The radar surface in the grille is dirty or covered with ice or snow.
Clean the radar surface in the grille from dirt, ice and snow.
Heavy rain or snow blocking the radar signals.
No action. Sometimes the radar does not work during heavy rain or snowfall.
Water or snow from the road surface swirls up and blocks the
radar signals.
No action. Sometimes the radar does not work on a very wet or snowy road
surface.
The radar surface has been cleaned but the message remains.
Wait. It could take several minutes for the radar to sense that it is no longer
blocked.
Related information
•
•
•
Adaptive cruise control (ACC)* (p. 198)
Adaptive cruise control* - overview
(p. 201)
Cruise control* (p. 193)
07
210
* Option/accessory, for more information, see Introduction.
07 Driver support
Adaptive cruise control* - symbols
and messages
are some examples - follow the recommendation given if appropriate:
Sometimes the adaptive cruise control may
display a symbol and/or text message. Here
SymbolA
Message
Specification
The symbol is WHITE
Adaptive cruise control is set to standby mode (p. 203).
The symbol is GREEN
The car maintains the stored speed.
Standard cruise control is selected manually.
Set ESC to Normal to enable Cruise
The adaptive cruise control cannot be activated until ESC has been set in Normal mode - Stability
system (p. 183).
Adaptive cruise control
cancelled
The adaptive cruise control has been deactivated - the driver has to regulate the speed himself.
Adaptive cruise control
unavailable
The adaptive cruise control cannot be activated.
This could be due to:
•
•
brake temperature is high
the radar sensor is blocked by e.g. wet snow or rain.
For more information about fault tracing, see section Fault tracing and action (p. 210)
07
}}
* Option/accessory, for more information, see Introduction.
211
07 Driver support
||
SymbolA
Message
Radar blocked See manual
Specification
The adaptive cruise control is temporarily disengaged.
•
The radar sensor is blocked and cannot detect other vehicles. For example, in the event of
heavy rain or if slush has collected in front of the radar sensor.
The driver can then choose to switch to normal Cruise control (p. 193) (CC) - a text message provides information on appropriate alternatives.
Read more about radar sensor limitations (p. 208).
Adaptive cruise control
Service required
The adaptive cruise control is disengaged.
Press brake to hold vehicle
+ acoustic alarm + warning
light in windscreen + "pulling" brakes
The car is at a standstill and the adaptive cruise control will release the foot brake, which is why the
car may start rolling soon.
•
•
Contact a workshop - an authorised Volvo workshop is recommended.
The driver must brake himself/herself. The message remains and the alarm sounds until the
driver depresses the brake pedal or uses the accelerator pedal.
(Only with Queue Assist)
Below 30 km/h Lead vehicle required
Shown with attempts to activate the adaptive cruise control at speeds below 30 km/h without a
vehicle in front within the activation distance (approx. 30 metres).
(Only with Queue Assist)
A
The symbols are schematic.
Related information
07
•
•
•
212
Adaptive cruise control (ACC)* (p. 198)
Adaptive cruise control* - overview
(p. 201)
Cruise control* (p. 193)
* Option/accessory, for more information, see Introduction.
07 Driver support
Distance Warning*
Distance Warning (Distance Alert) is a function
that informs the driver about the time interval
to vehicles in front.
Distance Warning is active at speeds above
30 km/h and only reacts to vehicles driving in
front of the car, in the same direction. No distance information is provided for oncoming,
slow or stationary vehicles.
NOTE
Distance warning is deactivated during the
time the adaptive cruise control is active.
tion is handled by the car's menu system MY
CAR, MY CAR (p. 108) - once there, search
for the Distance Alert function..
Set time interval
WARNING
Distance warning only reacts if the distance to the vehicle ahead is shorter than
the preset value - the speed of the driver's
vehicle is not affected.
Operation
Controls and symbol for time interval.
Time interval - Increase/decrease.
Time interval - On.
Orange-coloured warning lamp16.
An orange-coloured warning lamp in the
windscreen illuminates with a constant glow if
the distance to the vehicle in front is shorter
than the set time interval.
Press the button in the centre console to
switch the function on or off. The function is
switched on if one lamp is illuminated in the
button.
Some combinations of the selected equipment leave no vacant space for a button in
the centre console - in which case the func-
16
Different time intervals to the
vehicle in front can be
selected and shown in the
combined instrument panel
as 1-5 horizontal lines - the
more lines the longer the
time interval. One line corresponds to approximately 1 second to the
vehicle in front, 5 lines
approximately 3 seconds.
NOTE: The illustration is schematic - details may vary depending on car model.
07
}}
* Option/accessory, for more information, see Introduction.
213
07 Driver support
||
The same symbol is also shown when adaptive cruise control (p. 198) is activated.
NOTE
The higher the speed the longer the calculated distance in metres for a given time
interval.
Distance Alert* - limitations
Distance Warning (Distance Alert) is a function
that informs the driver about the distance to
vehicles in front. The function, which uses the
same radar sensor as the adaptive cruise control (p. 198) and collision warning with auto
brake (p. 223), has some limitations.
The set time interval is also used by the
function adaptive cruise control (p. 199).
Only use the time intervals permitted by
local traffic regulations.
Related information
•
•
Distance Alert* - limitations (p. 214)
Distance Alert* - symbols and messages
(p. 215)
NOTE
Strong sunlight, reflections or strong variations in light intensity, as well as wearing
sunglasses, could mean that the warning
light in the windscreen cannot be seen.
Poor weather or winding roads could
affect the radar sensor's capacity to detect
vehicles in front.
The size of other vehicles could also affect
detection capacity, e.g. motorcycles. This
could mean that the warning lamp illuminates at a shorter distance than the setting
or that the warning is temporarily absent.
Extremely high speeds can also cause the
lamp to illuminate at a shorter distance
than that set due to limitations in sensor
range.
07
214
For further information on radar sensor limitations, see Radar sensor - limitations (p. 208)
and Collision warning system* - operation
(p. 227).
* Option/accessory, for more information, see Introduction.
Related information
•
•
Distance Warning* (p. 213)
Distance Alert* - symbols and messages
(p. 215)
07 Driver support
Distance Alert* - symbols and
messages
Distance Warning (p. 213) (Distance Alert) is a
function that informs the driver about the time
SymbolA
interval to vehicles in front. The function has
certain symbols and messages that can be
displayed in the combined instrument panel if
Message
Specification
Radar blocked See
manual
Distance Warning temporarily disengaged.
the function is reduced due to its limitations
(p. 214).
Radar sensor (p. 208) is blocked and cannot detect other vehicles. For example, in the event of
heavy rain or if slush has collected in front of the radar sensor.
For information, see Radar sensor - limitations (p. 208).
Collision warning
Service required
A
Distance Warning and Collision Warning with Auto Brake (p. 228) fully or partially disengaged.
Visit a workshop if the message remains - an authorised Volvo workshop is recommended.
The symbols are schematic.
07
* Option/accessory, for more information, see Introduction.
215
07 Driver support
City Safety™
IMPORTANT
City Safety™ is a function for helping the
driver to avoid a collision when driving in
queues, amongst other things, when changes
in the traffic ahead, combined with a lapse in
attention, could lead to an incident.
Maintenance and replacement of City
Safety™ components must only be performed by a workshop - an authorised
Volvo workshop is recommended.
The City Safety™ function is active at speeds
under 50 km/h and it helps the driver by automatically braking the car in the event of imminent risk of collision with vehicles in front,
should the driver not react in time by braking
and/or steering away.
City Safety™ does not engage in all driving situations or traffic, weather or road
conditions.
WARNING
City Safety™ does not react to vehicles
driving in a different direction from the car,
to small vehicles and motorcycles or to
people and animals.
City Safety™ is activated in situations where
the driver should have started braking earlier,
which is why it cannot help the driver in every
situation.
City Safety™ can prevent collision at a
speed difference of less than 15 km/h - at
a higher speed difference, it is only possible to reduce collision speed. In order to
obtain full brake function, the driver must
depress the brake pedal.
City Safety™ is designed to be activated as
late as possible in order to avoid unnecessary
intervention.
City Safety™ must not be used as an excuse
for the driver to change his/her driving style. If
the driver solely relies on City Safety™ to do
the braking, there might be a risk of a collision sooner or later.
07
The driver or passengers normally only notice
City Safety™ if a situation arises where the
car is extremely close to being in a collision.
If the car is also equipped with Collision
Warning with Auto Brake (p. 223)* these two
systems complement each other.
216
Never wait for City Safety™ to engage.
The driver always bears responsibility for
maintaining the proper distance and
speed.
Related information
•
•
•
•
•
* Option/accessory, for more information, see Introduction.
City Safety™ - limitations (p. 218)
City Safety™ - function (p. 216)
City Safety™ - operation (p. 217)
City Safety™ - laser sensor (p. 220)
City Safety™ - symbols and messages
(p. 222)
City Safety™ - function
City Safety™ detects the traffic in front of the
car with a laser sensor (p. 220) fitted in the
top edge of the windscreen. If there is an
imminent risk of collision, City Safety™ will
automatically brake the car, which may be
experienced as sudden braking.
07 Driver support
When the function is activated and brakes,
the combined instrument panel shows a message (p. 222) to the effect that the function
is/has been active.
NOTE
When City Safety™ brakes, the brake
lights come on.
City Safety™ - operation
City Safety™ is a function for helping the
driver to avoid a collision when driving in
queues, amongst other things, when changes
in the traffic ahead, combined with a lapse in
attention, could lead to an incident.
On and Off
NOTE
Related information
Laser sensor transmitter and receiver
window17.
If the speed difference is 4-15 km/h in relation
to the vehicle in front then City Safety™ can
completely prevent a collision.
•
•
•
City Safety™ - operation (p. 217)
City Safety™ - limitations (p. 218)
City Safety™ activates a short, sharp braking
and stops the car in normal circumstances,
just behind the vehicle in front. For most drivers this is well outside normal driving style
and may be experienced as being uncomfortable.
If the difference in speed between the vehicles is greater than 15 km/h then City
Safety™ may not prevent the collision on its
own. To obtain full brake force, the driver
must depress the brake pedal. This could
then make it possible to prevent a collision,
even at speed differences above 15 km/h.
17
The City Safety™ function is activated
automatically when the engine is started.
City Safety™ (p. 216)
NOTE: The illustration is schematic - details may vary depending on car model.
In certain situations, it may advisable to disable City Safety™, e.g. where leafy branches
could sweep over the bonnet and/or windscreen.
City Safety™ handled in the menu system
MY CAR, MY CAR (p. 108) and after starting
the engine the function can be deactivated as
follows:
•
Search in MY CAR for Driver support
system and select the Off option at City
Safety.
However, the function will be enabled the
next time the engine is started, regardless
of whether the system was enabled or
disabled when the engine was switched
off.
07
}}
217
07 Driver support
||
WARNING
The laser sensor (p. 220) emits laser light
even when City Safety™ is disabled manually.
To enable City Safety™ again:
•
Follow the same procedure as for disabling, but select the On option.
Related information
•
•
•
City Safety™ (p. 216)
City Safety™ - limitations (p. 218)
City Safety™ - symbols and messages
(p. 222)
City Safety™ - limitations
The sensor in City Safety™ is designed to
detect cars and other large vehicles in front of
the car irrespective of whether it is day or
night.
However, the function does have some limitations.
The sensor's limitations mean that City
Safety™ has poorer functionality - or none at
all - in e.g. heavy snowfall or rain, dense fog,
dust storms or white-out situations. Misting,
dirt, ice or snow on the windscreen may also
disrupt the function.
Low-hanging objects, e.g. a flag/pennant for
projecting load, or accessories such as auxiliary lamps and bull bars that are higher than
the bonnet limit the function.
The laser light from the sensor in City
Safety™ measures how the light is reflected.
The sensor cannot detect objects with low
reflection capacity. The rear sections of the
vehicle generally reflect the light sufficiently
thanks to the number plate and rear light
reflectors.
07
On slippery road surfaces the braking distance is extended, which may reduce the
capacity of City Safety™ to avoid a collision.
In such situations the ABS18 and ESC19 sys-
18
19
218
(Anti-lock Braking System) - Anti-lock braking system.
(Electronic Stability Control) - Stability system.
tems will provide best possible braking force
with maintained stability.
When your own car is reversing, City Safety™
is temporarily deactivated.
City Safety™ is not activated at low speeds under 4 km/h, which is why the system does
not intervene in situations where a vehicle in
front is being approached very slowly, e.g.
when parking.
Driver commands are always prioritised,
which is why City Safety™ does not intervene
in situations where the driver is steering or
accelerating in a clear manner, even if a collision is unavoidable.
When City Safety™ has prevented a collision
with a stationary object the car remains stationary for a maximum of 1.5 seconds. If the
car is braked for a vehicle in front that is moving, then speed is reduced to the same speed
as that maintained by the vehicle in front.
On a car with manual gearbox the engine
stops when City Safety™ has stopped the
car, unless the driver manages to depress the
clutch pedal beforehand.
07 Driver support
NOTE
•
Keep the windscreen surface in front
of the laser sensor (p. 220) free from
ice, snow and dirt. For an illustration of
sensor location, see City Safety™ function (p. 216).
•
Do not affix or mount anything on the
windscreen in front of the laser sensor
•
Remove ice and snow from the bonnet
- snow and ice must not exceed a
height of 5 cm.
Cause
IMPORTANT
Action
The windscreen surface in front of the
laser sensor is dirty or
covered with ice or
snow.
Clean the windscreen surface in
front of the sensor
from dirt, ice and
snow.
The laser sensor field
of vision is blocked.
Remove the
blocking object.
If there are cracks, scratches or stone
chips in the windscreen in front of either of
the laser sensor's "windows" and they
cover a surface of approx. 0.5 x 3.0 mm
(or larger), then a workshop must be contacted for replacement of the windscreen an authorised Volvo workshop is recommended. For an illustration of sensor location, see City Safety™ - function (p. 216).
Failure to take action may result in
reduced performance for City Safety™.
To avoid the risk of failed, deficient or
reduced operation for City Safety™, the
following also applies:
Fault tracing and action
If the message (p. 222) Windscreen
sensors blocked See manual is shown in
the combined instrument panel it indicates
that the laser sensor is blocked and cannot
detect vehicles in front of the car. This means
that City Safety™ is not operational.
The Windscreen sensors blocked See
manual message is not shown for all situations in which the laser sensor is blocked.
The driver must therefore be diligent about
keeping the windscreen and area in front of
the laser sensor clean.
The following table presents possible causes
for the message being shown, along with
suggestions for appropriate action.
•
Volvo recommends that you do not
repair cracks, scratches or stone chips
in the area in front of the laser sensor instead, the whole windscreen should
be replaced.
•
Before replacing a windscreen, contact an authorised Volvo workshop to
verify that the correct windscreen is
ordered and fitted.
•
The same type or Volvo-approved
windscreen wipers must be fitted during replacement.
07
Related information
•
•
•
City Safety™ (p. 216)
City Safety™ - function (p. 216)
City Safety™ - operation (p. 217)
219
07 Driver support
City Safety™ - laser sensor
The City Safety™ function includes a sensor
which transmits laser light. Contact a qualified
workshop in the event of a fault or if the laser
sensor needs servicing - an authorised Volvo
workshop is recommended. It is absolutely
essential to follow the prescribed instructions
when handling the laser sensor.
The following two labels relate to the laser
sensor:
standards for laser product design with
the exception of deviations in accordance
with "Laser Notice No. 50" from
26 July 2001.
Radiation data for the laser sensor
Maximum pulse energy
2.64 µJ
Maximum average output
45 mW
Divergence (horizontal x vertical)
07
•
Laser radiation - Do not look into the
laser beam with optical instruments Class 1M laser product.
The lower label in the figure describes the
laser beam's physical data:
•
220
IEC 60825-1:1993 + A2:2001. Complies
with FDA (U.S. Food Administration)
•
Never look into the laser sensor (which
emits spreading invisible laser radiation) at a distance of 100 mm or closer
with magnifying optics such as a magnifying glass, microscope, lens or similar optical instruments.
•
Testing, repair, removal, adjustment
and/or replacement of the laser sensor's spare parts must only be carried
out by a qualified workshop - we recommend an authorised Volvo workshop.
•
To avoid exposure to harmful radiation, do not carry out any readjustments or maintenance other than
those specified here.
•
The repairer must follow specially
drawn up workshop information for the
laser sensor.
•
Do not remove the laser sensor (this
includes removing the lenses). A
removed laser sensor fulfils laser
class 3B as per standard IEC 60825-1.
Laser class 3B is not eye-safe and
therefore entails a risk of injury.
•
The laser sensor's connector must be
unplugged before removal from the
windscreen.
The following table specifies the laser sensor's physical data.
Pulse duration
The upper label in the figure describes the
laser beam's classification:
WARNING
If any of these instructions are not followed
then there is a risk of eye injury!
33 ns
28° × 12°
07 Driver support
•
The laser sensor must be fitted onto
the windscreen before the sensor's
connector is plugged in.
•
The laser sensor transmits a laser light
when the remote control key is in key
position II (p. 76) even if the engine is
switched off.
Related information
•
City Safety™ (p. 216)
07
221
07 Driver support
City Safety™ - symbols and
messages
In conjunction with automatic braking by the
City Safety (p. 216)™ system, one or more
SymbolA
symbols (p. 222) may illuminate in the combined instrument panel and a text message
may be shown. A text message can be
acknowledged by briefly pressing the OK button on the direction indicator stalk.
Message
Meaning/Action
Auto braking by City Safety
City Safety™ is braking or has automatically braked.
Windscreen sensors blocked
See manual
The laser sensor is temporarily non-operational because something is blocking it.
•
Remove the object blocking the sensor and/or clean the windscreen in front of the sensor.
Read about the laser sensor's limitations.
City Safety Service required
City Safety™ is not operational.
•
A
The symbols are schematic.
Related information
•
•
07
222
City Safety™ (p. 216)
City Safety™ - function (p. 216)
Visit a workshop if the message remains - an authorised Volvo workshop is recommended.
07 Driver support
Collision warning system*
"Collision Warning with Auto Brake and
Cyclist and Pedestrian Detection" is an aid to
assist the driver when there is a risk of colliding with a pedestrian, cyclist or vehicle in
front that are stationary or moving in the same
direction.
"Collision Warning with Auto Brake and
Cyclist and Pedestrian Detection" is activated
in situations where the driver should have
started braking earlier, which is why it cannot
help the driver in every situation.
"Collision Warning with Auto Brake and
Cyclist and Pedestrian Detection" is designed
to be activated as late as possible in order to
avoid unnecessary intervention.
Cyclist and Pedestrian Detection" function
may appear in two variants:
•
Collision warning system* - operation
(p. 227)
Level 1
•
Collision warning system* - limitations
(p. 229)
•
Collision warning system* - camera sensor limitations (p. 230)
•
Collision warning system* - symbols and
messages (p. 231)
warned20
The driver is merely
of occurring
obstacles by means of visual and acoustic
signals - no automatic braking intervenes, the
driver must himself brake.
Level 2
The driver is warned of occurring obstacles
by means of visual and acoustic signals - the
car is braked automatically if the driver himself does not act within a reasonable time.
IMPORTANT
Maintenance of the internal components of
the "Collision Warning with Auto Brake
and Cyclist and Pedestrian Detection"
must only be performed at a workshop an authorised Volvo workshop is recommended.
"Collision Warning with Auto Brake and
Cyclist and Pedestrian Detection" can prevent a collision or reduce collision speed.
"Collision Warning with Auto Brake and
Cyclist and Pedestrian Detection" must not
be used as an excuse for the driver to change
his/her driving style. If the driver solely relies
on Collision Warning with Auto Brake to do
the braking, there might be a risk of a collision sooner or later.
Two system levels
Depending on how the car is equipped, the
"Collision Warning with Auto Brake and
20
Related information
•
Collision warning system* - function
(p. 224)
•
Collision warning system* - detection of
pedestrians (p. 226)
•
Collision warning system* - detection of
cyclists (p. 225)
07
No warning for cyclists with "Level 1".
* Option/accessory, for more information, see Introduction.
223
07 Driver support
Collision warning system* - function
1 - Collision warning
The driver is first warned of a potentially
imminent collision.
The collision warning system can detect
pedestrians, cyclists or vehicles that are stationary or moving in the same direction in
front of the driver's vehicle.
If there is a risk of collision with a pedestrian,
cyclist or a vehicle then the driver's attention
is attracted with a flashing red warning signal
(1) and an acoustic signal.
2 - Brake support
Function overview21.
Audio-visual warning signal in the event
of a collision risk.
Radar sensor22
Camera sensor
Collision Warning with Auto Brake executes
three steps in the following order:
1. Collision warning
2. Brake support22
07
3. Auto Brake22
The collision warning system and City
Safety™ (p. 216) complement each other.
21
22
224
If the risk of collision has increased further
after the collision warning then the brake support is activated.
This means that the brake system is prepared
for rapid braking by applying the brakes
lightly, which may feel like a slight jolt.
If the brake pedal is depressed sufficiently
quickly then full brake function is implemented.
Brake support also reinforces the driver's
braking if the system considers that the braking is not sufficient to avoid a collision.
3 - Auto Brake
The automatic brake function is activated
last.
NOTE: The illustration is schematic - details may vary depending on car model.
With system Level 2 only.
* Option/accessory, for more information, see Introduction.
If in this situation the driver has not yet
started to take evasive action and the risk of
collision is imminent then the automatic braking function is deployed - this takes place
irrespective of whether or not the driver
brakes. Braking then takes place with full
brake force in order to reduce collision speed,
or with limited brake force if it is sufficient to
avoid a collision. For cyclists, the warning and
full brake intervention may come very late or
simultaneously.
07 Driver support
WARNING
The collision warning system does not
engage in all driving situations or traffic,
weather or road conditions. The collision
warning system does not react to vehicles
or cyclists driving in another direction to
the car or to animals.
Collision warning system* - detection
of cyclists
Optimal performance of the system requires
that the system function that detects a cyclist
receives as unambiguous information as possible about the body and bicycle contours this implies the opportunity to identify the
bicycle, head, arms, shoulders, legs, upper
and lower body combined with a normal
human pattern of movement.
Warning only activated in the event of a
high risk for collision. This section "Function" and the section "Limitations" inform
about limitations that the driver must be
aware of before using the Collision Warning system with Auto Brake.
Warnings and brake interventions for
pedestrians and cyclists are deactivated at
a vehicle speed exceeding 80 km/h.
Warnings and brake interventions for
pedestrians and cyclists do not work in
darkness and tunnels - not even when
streetlights are lit.
If large parts of the cyclist's body or bicycle
are not visible to the function's camera then
the system cannot detect a cyclist.
Related information
•
23
•
For the function to be able to detect a
cyclist, he/she must be an adult and riding a "senior bicycle".
•
The function can only detect cyclists
directly from behind and who are travelling in the same direction - not at an
angle from behind, not from the side.
•
The bicycle must be equipped with a
highly visible and approved23 rearwardfacing red reflector, fitted at least 70 cm
above the roadway.
•
Cyclists travelling on the left or right-hand
edge of the car's imagined/extended side
lines may be detected late or not at all.
•
The function's capacity to detect cyclists
at dusk and dawn is limited - just like the
human eye.
The function only "sees" cyclists from behind,
who are travelling in the same direction.
The auto-brake function can prevent a collision or reduce collision speed. To ensure
full brake performance, the driver should
always depress the brake pedal - even
when the car auto-brakes.
Never wait for a collision warning. The
driver is always responsible that the correct distance and speed are maintained even when the collision warning system
with auto-brake is used.
tours, directly from behind and in the car's centre line.
Optimal example of what the system interprets
as a cyclist - with clear body and bicycle con-
07
Collision warning system* (p. 223)
The reflector must fulfil the recommendations and conditions of the traffic authority in the market in question.
}}
* Option/accessory, for more information, see Introduction.
225
07 Driver support
||
•
The function's capacity to detect cyclists
is deactivated when driving in darkness
and tunnels - even when streetlights are
lit.
•
For optimum bicycle detection, the City
Safety™ function must be activated, see
City Safety™ (p. 216).
Collision warning system* - detection
of pedestrians
•
In order for a pedestrian to be detected
he/she must appear full-length and have
a height of at least 80 cm.
•
The camera sensor's ability to see pedestrians at dusk and dawn is limited - just
like the human eye.
•
The camera sensor's capacity to detect
pedestrians is deactivated when driving in
darkness and tunnels - even when streetlights are lit.
WARNING
Collision Warning with Auto Brake &
Cyclist Detection is a means of assistance.
WARNING
The function cannot detect:
•
all cyclists in all situations and does
not see partially obscured cyclists, for
example.
•
cyclists in clothing that obscures the
contours of the body or who are
approaching from the side.
•
bicycles that have no rearward-facing
red reflector.
• bicycles loaded with large objects.
The driver is always responsible that the
vehicle is driven properly and with a safety
distance adapted to the speed.
07
Related information
•
Collision warning system* (p. 223)
"Collision Warning with Auto Brake and
Cyclist and Pedestrian Detection" is a
means of assistance. The function cannot
detect all pedestrians in all situations and
does not see, for example:
Optimal examples of what the system regards as
pedestrians with clear body contours.
Optimal performance of the system requires
that the system function that detects pedestrians receives as unambiguous information
as possible about the contours of the body this implies the opportunity to identify the
head, arms, shoulders, legs, upper and lower
body combined with a normal human pattern
of movement.
If large parts of the body are not visible to the
function's camera then the system cannot
detect a pedestrian.
•
•
pedestrians who are carrying larger
objects.
The driver is always responsible that the
vehicle is driven properly and with a safety
distance adapted to the speed.
Related information
•
226
* Option/accessory, for more information, see Introduction.
partially obscured pedestrians, people
in clothing that hides their body contour or pedestrians shorter than
80 cm.
Collision warning system* (p. 223)
07 Driver support
Collision warning system* - operation
Settings for the collision warning system are
made from MY CAR via the centre console
screen and menu system, see MY CAR
(p. 108).
Warning signals On and Off
NOTE
The Brake Support and Auto Brake functions are always activated - they cannot be
deactivated.
Settings for the collision warning system are
made via the centre console's screen and the
menu system MY CAR, see MY CAR (p. 108).
Light and acoustic signals
When the collision warning system's light and
acoustic warnings are activated, the warning
lamp (no. [1] in previous illustration) is tested
each time the engine is started by briefly illuminating the warning lamp's separate points
of light.
After starting the engine, both light and
acoustic signals are switched off:
1. Acoustic and visual warning signal in the event
of a collision risk.24
•
Search for Collision Warning in Driver
support systems in the menu system
MY CAR, MY CAR (p. 108) - and there
select to uncheck the function.
It is possible to select whether the collision
warning system's acoustic and visual warning
signals should be switched on or off.
Audible signal
When starting the engine, the setting that was
selected when the engine was switched off is
obtained automatically.
•
24
Following which, the collision warning system
is only indicated with a light signal.
Set warning distance
The warning distance regulates the distance
at which the visual and acoustic warnings are
deployed.
•
Search for Warning distance in
Collision Warning in the menu system
MY CAR, MY CAR (p. 108) - and there
select Long, Normal or Short.
The warning distance determines the system's sensitivity. Warning distance Long provides an earlier warning. First test with Long
and if this setting produces too many warnings, which could be perceived as irritating in
certain situations, then change to warning
distance Normal.
Only use warning distance Short in exceptional cases, e.g. for dynamic driving.
After starting the engine the warning sound
can be activated/deactivated separately:
Search for Warning sound in Collision
Warning in the menu system MY CAR,
MY CAR (p. 108) - and there select On or
Off.
The illustration is schematic - car model and details may differ.
07
}}
* Option/accessory, for more information, see Introduction.
227
07 Driver support
||
NOTE
When the adaptive cruise control is in use
the warning lamp and warning sound will
be used by the cruise control even if the
collision warning system is switched off.
The collision warning system warns the
driver in the event of a risk of a collision,
but the function cannot shorten driver
reaction time.
Checking settings
The settings required can be controlled on
the centre console display screen.
•
Search in the menu system MY CAR
(p. 108) for Collision Warning in Driver
support systems.
Maintenance
In order for the collision warning system to
be effective, always drive with Distance
Alert (p. 213) set at time interval 4–5.
NOTE
Even if the warning distance has been set
to Long warnings could be perceived as
being late in certain situations, e.g. when
there are large differences in speed or if
vehicles in front brake heavily.
Camera and radar sensor25.
WARNING
No automatic system can guarantee
100 % correct function in all situations.
Therefore, never test Collision Warning
with Auto Brake by driving at people or
vehicles - this may cause severe damage
and injury and risk lives.
07
25
228
For the sensors to work correctly, they must
be kept clear of dirt, ice and snow, and be
cleaned regularly with water and car shampoo.
NOTE
Dirt, ice and snow covering the sensors
will reduce their function and may prevent
measurement.
NOTE: The illustration is schematic - details may vary depending on car model.
* Option/accessory, for more information, see Introduction.
Related information
•
Collision warning system* (p. 223)
07 Driver support
Collision warning system* - limitations
The function has certain limitations - for
example, it is not active until approx. 4 km/h.
The collision warning system's visual warning
signal may be difficult to notice in the event of
strong sunlight, reflections, when sunglasses
are being worn or if the driver is not looking
straight ahead. The warning sound should
therefore always be activated.
On slippery road surfaces the braking distance is extended, which may reduce the
capacity to avoid a collision. In such situations the ABS and ESC (p. 183) systems will
provide best possible braking force with
maintained stability.
NOTE
The visual warning signal can be temporarily disengaged in the event of high passenger compartment temperature caused by
strong sunlight for example. If this occurs
then the warning sound is activated even if
it is deactivated in the menu system.
•
26
Warnings may not appear if the distance to the vehicle in front is small or
if steering wheel and pedal movements are large, e.g. a very active driving style.
WARNING
Warnings and brake interventions could be
implemented late or not at all if the traffic
situation or external influences mean that
the radar or camera sensor cannot detect
a pedestrian, a vehicle or a cyclist in front
correctly.
The sensor system has a limited range for
pedestrians and cyclists26 - the system
can provide effective warnings and brake
interventions for them at vehicle speeds up
to 50 km/h. For stationary or slow-moving
vehicles, warnings and brake interventions
are effective at vehicle speeds up to
70 km/h.
Warnings for stationary or slow-moving
vehicles could be disengaged due to darkness or poor visibility.
Warnings and brake interventions for
pedestrians and cyclists are deactivated at
vehicle speeds exceeding 80 km/h.
The collision warning system uses the same
radar sensors as the adaptive cruise control
(p. 198).
Collision Warning with Auto Brake is temporarily deactivated with reverse gear engaged.
Collision Warning with Auto Brake is not activated at low speeds - under 4 km/h, which is
why the system does not intervene in situations where the car is approaching a vehicle
in front very slowly, e.g. when parking.
In situations where the driver demonstrates
active, aware driving behaviour, a collision
warning may be postponed slightly in order to
keep unnecessary warnings to a minimum.
When Auto Brake has prevented a collision
with a stationary object the car remains stationary for a maximum of 1.5 seconds. If the
car is braked for a vehicle in front that is moving, then speed is reduced to the same speed
as that maintained by the vehicle in front.
On a car with manual gearbox the engine
stops when Auto Brake has stopped the car,
unless the driver manages to depress the
clutch pedal beforehand.
Related information
•
Collision warning system* (p. 223)
If warnings are perceived as being too frequent or disturbing then the warning distance
can be reduced. This then leads to the system providing a warning at a later stage,
which reduces the total number of warnings;
see Collision warning system - operation
(p. 227).
07
For cyclists, the warning and full brake intervention may come very late or simultaneously.
* Option/accessory, for more information, see Introduction.
229
07 Driver support
Collision warning system* - camera
sensor limitations
The function uses the car's camera sensor,
which has certain limitations.
The car’s camera sensor is also used - as
well as by Collision Warning with Auto Brake
- by the functions:
•
•
•
•
Active high beam (p. 87)
Road sign information (p. 187)
Driver Alert Control - DAC (p. 232)
Lane Keeping Aid (p. 236).
NOTE
Keep the windscreen surface in front of the
camera sensor free from ice, snow, mist
and dirt.
Do not stick or attach anything to the
windscreen in front of the camera sensor
as this may reduce effectiveness or cause
one or more of the systems dependent on
the camera to stop working.
07
The camera sensors have limitations similar
to the human eye, i.e. they "see" worse in
darkness, heavy snowfall or rain and in thick
fog for example. Under such conditions the
functions of camera-dependent systems
could be significantly reduced or temporarily
disengaged.
Strong oncoming light, reflections in the carriageway, snow or ice on the road surface,
230
dirty road surfaces or unclear lane markings
could also significantly reduce camera sensor
function when it is used to scan the carriageway and detect pedestrians and other vehicles.
The field of vision of the camera sensor is limited, which is why pedestrians, cyclists and
vehicles cannot be detected in some situations, or they are detected later than anticipated.
During very high temperatures the camera is
temporarily switched off for
approx. 15 minutes after the engine is started
in order to protect camera functionality.
Fault tracing and action
If the display shows the message
Windscreen sensors blocked See manual
then this means that the camera sensor is
blocked and cannot detect pedestrians,
cyclists, vehicles or road markings in front of
the car.
At the same time, this means that - besides
Collision Warning with Auto Brake - the Automatic main/dipped beam dimming, Road Sign
Information, Driver Alert Control and Lane
Keeping Aid functions will not have full functionality either.
The following table presents possible causes
for a message being shown along with the
appropriate action.
* Option/accessory, for more information, see Introduction.
Cause
Action
The windscreen
surface in front of
the camera is dirty
or covered with ice
or snow.
Clean the windscreen surface in
front of the camera
from dirt, ice and
snow.
Thick fog, heavy
rain or snow means
that the camera
does not work sufficiently well.
No action. At times
the camera does
not work during
heavy rain or snowfall.
The windscreen
surface in front of
the camera has
been cleaned but
the message
remains.
Wait. It may take
several minutes for
the camera to
measure the visibility.
Dirt has appeared
between the inside
of the windscreen
and the camera.
Visit a workshop to
have the windscreen inside the
camera cover
cleaned - an authorised Volvo workshop is recommended.
Related information
•
Collision warning system* (p. 223)
07 Driver support
Collision warning system* - symbols
and messages
SymbolA
Message
Specification
Collision warning system OFF
Collision warning system switched off.
Shown when the engine is started.
The message clears after about 5 seconds or after one press of the OK button.
Collision warning system Unavailable
The collision warning system cannot be activated.
Shown when the driver attempts to activate the function.
The message clears after about 5 seconds or after one press of the OK button.
Auto Braking was activated
Auto Brake has been active.
Windscreen sensors
blocked See manual
Camera sensor (p. 230) is temporarily disengaged.
The message clears after one press of the OK button.
Shown in the event of snow, ice or dirt on the windscreen for example.
•
A
Clean the windscreen surface in front of the camera sensor.
Radar blocked See
manual
Collision Warning with Auto Brake is temporarily disengaged.
Collision warning Service required
Collision Warning with Auto Brake is fully or partially disengaged.
Radar sensor (p. 208) is blocked and cannot detect other vehicles. For example, in the event of heavy
rain or if slush has collected in front of the radar sensor.
•
07
Visit a workshop if the message remains - an authorised Volvo workshop is recommended.
Symbols are schematic - may vary by market and car model.
Related information
•
Collision warning system* (p. 223)
* Option/accessory, for more information, see Introduction.
231
07 Driver support
Driver Alert System*
Driver Alert Control (DAC)*
The Driver Alert System is intended to assist
drivers whose driving ability is deteriorating or
who are inadvertently leaving the lane they are
driving on.
DAC is intended to attract the driver's attention when he/she starts to drive less consistently, e.g. if he/she becomes distracted or
starts to fall asleep.
The Driver Alert System consists of different
functions which can either be switched on at
the same time or individually:
The objective for DAC is to detect slowly
deteriorating driving ability and it is primarily
intended for major roads.
•
•
Driver Alert Control - DAC (p. 233).
driver fatigue, irrespective of whether or not
DAC issues a warning.
NOTE
The function must not be used to extend a
period of driving. Always plan breaks at
regular intervals, and make sure you are
well rested.
Limitation
Lane Keeping Aid (p. 238).
In some cases the system may issue a warning despite driving ability not deteriorating, for
example:
A switched-on function is set in standby
mode and is not activated automatically until
speed exceeds 65 km/h.
•
•
The function is deactivated again when speed
decreases to below 60 km/h.
DAC is not intended for city traffic.
The functions use a camera which is dependent on the lane having side markings painted
on each side.
WARNING
Driver Alert System does not work in all
situations but is designed merely as a supplementary aid.
07
The driver always bears ultimate responsibility for ensuring that the vehicle is driven
safely.
Related information
•
•
232
Driver Alert Control (DAC)* (p. 232)
in strong side winds
on rutted road surfaces.
NOTE
A camera detects the side markings painted
on the carriageway and compares the section
of the road with the driver's steering wheel
movements. The driver is alerted if the vehicle
does not follow the carriageway evenly.
In some cases driving ability is not affected
despite driver fatigue. In which case there
may not be any warning issued for the driver.
For this reason it is always important to stop
and take a break in the event of any signs of
Lane Keeping Aid* (p. 236)
* Option/accessory, for more information, see Introduction.
The camera sensor has certain limitations,
see Collision warning system* - camera
sensor limitations (p. 230).
Related information
•
•
Driver Alert System* (p. 232)
•
Driver Alert Control (DAC)* - symbols and
messages (p. 234)
•
Lane Keeping Aid* (p. 236)
Driver Alert Control (DAC)* - operation
(p. 233)
07 Driver support
Driver Alert Control (DAC)* - operation
WARNING
Settings are made from the centre console
display screen and its menu system.
An alarm should be taken very seriously,
as a sleepy driver is often not aware of
his/her own condition.
On/Off
In the event of an alarm or a feeling of
tiredness; stop the car in a safe manner as
soon as possible and rest.
The Driver Alert function can be set in
standby mode via the menu system MY CAR
(p. 108):
•
•
Studies have shown that it is equally as
dangerous to drive while tired as it is under
the influence of alcohol.
Checked box - function activated.
Unchecked box - the function is deactivated.
Function
Driver Alert is activated when speed exceeds
65 km/h and remains active as long as the
speed is over 60 km/h.
Related information
•
•
Driver Alert System* (p. 232)
Driver Alert Control (DAC)* (p. 232)
If the vehicle is being driven erratically, the driver is notified by an
acoustic signal plus the text message (p. 234) Driver Alert Time for
a break - the linked symbol is illuminated in
the combined instrument panel at the same
time. The warning is repeated after a time if
driving ability does not improve.
The warning symbol can go off:
•
07
Press the left stalk switch OK button.
* Option/accessory, for more information, see Introduction.
233
07 Driver support
Driver Alert Control (DAC)* - symbols
and messages
instrument panel or in the centre console's
screen in different situations.
Driver Alert Control - DAC (p. 232) can show
symbols and text messages in the combined
Combined instrument panel
SymbolA
Message
Specification
Driver Alert Time for a
break
The vehicle has been driven inconsistently - the driver is alerted by an acoustic warning signal + text.
Windscreen sensors
blocked See manual
The camera sensor is temporarily disengaged.
Shown in the event of snow, ice or dirt on the windscreen for example.
•
Clean the windscreen surface in front of the camera sensor.
Read about the limitations of the camera sensor, see Collision warning system* - camera sensor limitations (p. 230).
Driver Alert system
Service required
A
The system is disengaged.
•
Visit a workshop if the message remains - an authorised Volvo workshop is recommended.
The symbols are schematic.
Display
07
234
Symbol
Message
Specification
Driver Alert OFF
The function is disengaged.
Driver Alert Available
The function is activated.
* Option/accessory, for more information, see Introduction.
07 Driver support
Symbol
Message
Specification
Driver Alert Standby <65
km/h
The function is set in standby mode due to speed being lower than 65 km/h.
Driver Alert Unavailable
The carriageway does not have clear side markings or the camera sensor is temporarily disengaged.
Read about the limitations of the camera sensor, see Collision warning system* - camera sensor limitations (p. 230).
Related information
•
•
Driver Alert System* (p. 232)
•
Lane Keeping Aid* (p. 236)
Driver Alert Control (DAC)* - operation
(p. 233)
07
* Option/accessory, for more information, see Introduction.
235
07 Driver support
Lane Keeping Aid*
WARNING
Lane Keeping Aid is one of the functions in
the Driver Alert System - sometimes also
referred to as LKA (Lane Keeping Aid).
LKA is merely a driver's aid and does not
engage in all driving situations or traffic,
weather or road conditions.
The function is intended for use on motorways and similar major roads in order to
reduce the risk of the vehicle accidentally
leaving its own lane in certain situations.
The driver always bears ultimate responsibility for ensuring that the vehicle is driven
safely and that applicable laws and road
traffic regulations are followed.
Lane Keeping Aid - function
Off & On
Lane Keeping Aid is active within the speed
range 65-200 km/h on roads with clearly visible side lines. The function is temporarily
deactivated on narrow roads with less than
2.6 metres between the lane side lines.
Related information
•
•
•
•
•
07
A camera reads the painted side lines of the
road/lane. If the car is about to cross a side
line then Lane Keeping Aid will actively steer
the car back into the lane with a slight steering torque in the steering wheel.
If the car reaches or crosses a side line then
Lane Keeping Aid will also alert the driver with
pulsating vibration in the steering wheel.
Lane Keeping Aid - function (p. 236)
Lane Keeping Aid - operation (p. 238)
Lane Keeping Aid - limitations (p. 238)
Lane Keeping Aid - symbols and messages (p. 240)
Driver Alert System* (p. 232)
Press the button in the centre console to activate or deactivate the function. An illuminated
lamp in the button shows when the function
is switched on.
Some combinations of the selected equipment leave no vacant space for an On/Off
button in the centre console - in which case
the function is instead handled in the car's
menu system MY CAR, MY CAR (p. 108).
There, proceed as follows:
•
236
* Option/accessory, for more information, see Introduction.
Search for Lane Keeping Aid and then
select On or Off.
07 Driver support
In addition, the following selections can be
made in MY CAR:
•
Warning with vibration in the steering
wheel: Vibration only - On or Off.
•
Active steering: Steering assist only On or Off.
Both Warning with vibration in the steering wheel and Active steering: Full
function - On or Off.
•
Warning with vibration in the steering
wheel
Dynamic cornering
Active steering
Lane Keeping Aid strives to keep the car
within the side lines for the lane.
LKA does not engage in sharp inside curves.
LKA steers and warns with pulsing steering
wheel vibrations27.
If the vehicle crosses a side line then Lane
Keeping Aid alerts the driver with pulsating
vibration in the steering wheel. This occurs
regardless of whether the car is actively
steered back by applying a slight steering torque.
In certain cases, Lane Keeping Aid allows the
car to cross side lines without engaging
active steering or alerting with pulsating
vibration in the steering wheel. Using an adjacent lane for dynamic cornering when there is
a clear line of vision is an example of one
such case.
Related information
•
Lane Keeping Aid* (p. 236)
LKA intervenes and steers away.
07
If the vehicle approaches the left or right side
line of the lane and the direction indicator is
not activated, the car is steered back into the
lane.
27
The figure shows 3 pulsing vibrations when the side line is passed.
* Option/accessory, for more information, see Introduction.
237
07 Driver support
Lane Keeping Aid - operation
Lane Keeping Aid - limitations
Lane Keeping Aid is supplemented with selfexplanatory graphics in different situations.
Here are some examples:
•
Lane Keeping Aid's camera sensor has
limitations in a similar way to the human
eye. For more information, see Collision
warning system* - camera sensor limitations (p. 230) and (p. 228).
NOTE
LKA is temporarily deactivated for as long
as the direction indicator is switched on.
NOTE
LKA engages on the right side.
Lane Keeping Aid intervenes and steers away
from the side line - this is indicated with:
•
RED line for the side in question.
Related information
•
LKA "sees" the following side lines.
07
If Lane Keeping Aid is active and
detects/"sees" the side lines, the LKA symbol
indicates this with WHITE lines.
•
238
GREY side line - Lane Keeping Aid does
not see a line on that side of the car.
* Option/accessory, for more information, see Introduction.
Lane Keeping Aid* (p. 236)
In certain demanding situations LKA may
find it difficult to assist the driver correctly
- in which case it is recommended that
LKA is switched off.
Examples of such a situation could be:
•
•
•
•
•
roadworks
winter road conditions
poor road surface
very sporty driving style
poor weather with reduced visibility.
Hands on the steering wheel
In order for Lane Keeping Aid to operate, the
driver must have his/her hands on the steering wheel. LKA continually monitors this. If
hands are not detected on the steering wheel
then a text message is shown, prompting the
driver to actively steer the car.
If the driver does not follow the request to
begin steering then Lane Keeping Aid goes
into standby mode and will remain in this
mode until the driver begins to steer the car
again.
07 Driver support
Related information
•
Lane Keeping Aid* (p. 236)
07
* Option/accessory, for more information, see Introduction.
239
07 Driver support
Lane Keeping Aid - symbols and
messages
the combined instrument panel in combination with an explanatory message - follow the
recommendation given if appropriate.
In situations where there is no LKA function
or it is interrupted, a symbol may be shown in
SymbolA
Message examples:
Message
Specification
Lane Keeping Aid Unavailable at this speed
Lane Keeping Aid is set in standby mode due to speed being lower than 65 km/h.
Lane Keeping Aid Unavailable for current markings
The lane does not have clear side lines or the camera sensor is temporarily disengaged. Read
about the limitations of the camera sensor, see Collision warning system* - camera sensor limitations (p. 230) and (p. 228).
Lane Keeping Aid Available
The function scans the lane's side lines.
Windscreen sensors
blocked See manual
The camera sensor is temporarily disengaged.
Shown in the event of snow, ice or dirt on the windscreen for example.
•
Clean the windscreen surface in front of the camera sensor.
Read about the limitations of the camera sensor, see Collision warning system* - camera sensor
limitations (p. 230) and (p. 228).
07
A
Lane Keeping Aid Service
required
The system is disengaged.
Lane Keeping Aid Interrupted
LKA has been set to standby mode. The lines of the LKA symbol indicate when the function is
active again.
•
Visit a workshop if the message remains - an authorised Volvo workshop is recommended.
The table's symbols are schematic. The symbols shown in the combined instrument panel may have a slightly different appearance.
Related information
•
240
Lane Keeping Aid* (p. 236)
* Option/accessory, for more information, see Introduction.
07 Driver support
Park assist syst*
Parking assistance is used as an aid to parking. An acoustic signal as well as symbols on
the centre console's display screen indicate
the distance to the detected obstacle.
Parking assistance sound level can be
adjusted during the ongoing acoustic signal
using the centre console's VOL knob or in the
car's menu system MY CAR, see MY CAR
(p. 108).
Park assist syst* - function
Related information
•
Park assist syst* - cleaning the sensors
(p. 244)
•
•
•
•
•
•
Park assist syst* - function (p. 241)
Park assist syst* - forward (p. 243)
Park assist syst* - fault indication (p. 244)
The parking assistance system is automatically activated when the engine is started the switch's On/Off lamp is illuminated. If
parking assistance is switched off with the
button, the lamp goes out.
Park assist syst* - backward (p. 243)
Park assist camera (p. 245)
Park Assist Pilot (PAP)* (p. 249)
Parking assistance is available in two variants:
•
•
Rear only
Both front and rear.
NOTE
When a towbar is configured with the car's
electrical system, the protrusion of the
towbar is included when the function
measures the parking space.
WARNING
•
Parking assistance does not relinquish
the driver's own responsibility during
parking.
•
The sensors have blind spots where
obstacles cannot be detected.
•
Be aware of e.g. people and animals
near the car.
07
}}
* Option/accessory, for more information, see Introduction.
241
07 Driver support
||
Marked sectors show which of the four sensor(s) detected an obstacle. The closer to the
car symbol a selected sector box is, the
shorter the distance between the car and a
detected obstacle.
IMPORTANT
Objects e.g. chains, thin glossy poles or
low barriers may be in the "signal shadow"
and are then temporarily not detected by
the sensors - the pulsating tone may then
unexpectedly stop instead of changing
over to the expected constant tone.
The frequency of the signal increases the
shorter the distance to an obstacle, in front of
or behind the car. Other sound from the audio
system is muted automatically.
On/Off for the sensors for parking assistance and
CTA28.
The centre console's display screen shows
an overview of the relationship between the
car and detected obstacle.
The sensors cannot detect high objects,
such as projecting loading docks.
•
When the distance is within 30 cm the tone is
constant and the active sensor's field nearest
the car is filled in. If the detected obstacle is
within the distance for the constant tone both
behind and in front of the car, then the tone
sounds alternately from the loudspeakers.
In such situations, pay extra attention
and manoeuvre/reposition the car particularly slowly or stop the current
parking manoeuvre - there may be a
high risk of damage to vehicles or
other objects since the sensors are
temporarily unable to function optimally.
Related information
•
•
•
•
•
•
•
07
Display screen view - showing an obstacle left
front and right rear.
28
242
Side warning, CTA (Cross Traffic Alert) (p. 256)
* Option/accessory, for more information, see Introduction.
Park assist syst* (p. 241)
Park assist syst* - cleaning the sensors
(p. 244)
Park assist syst* - forward (p. 243)
Park assist syst* - fault indication (p. 244)
Park assist syst* - backward (p. 243)
Park assist camera (p. 245)
Park Assist Pilot (PAP)* (p. 249)
07 Driver support
Park assist syst* - backward
Park assist syst* - forward
NOTE
Parking assistance is used as an aid to parking. An acoustic signal as well as symbols on
the centre console's display screen indicate
the distance to the detected obstacle.
When reversing with e.g. a trailer or bike
carrier on the towbar - without Volvo genuine trailer wiring - parking assistance may
need to be switched off manually in order
that the sensors do not react to them.
Related information
•
•
•
•
•
•
•
Park assist syst* (p. 241)
Park assist syst* - cleaning the sensors
(p. 244)
Parking assistance is used as an aid to parking. An acoustic signal as well as symbols on
the centre console's display screen indicate
the distance to the detected obstacle.
The parking assistance system is automatically activated when the engine is started the switch's On/Off lamp is illuminated. If
parking assistance is switched off with the
button, the lamp goes out.
Park assist syst* - function (p. 241)
Park assist syst* - forward (p. 243)
Park assist syst* - fault indication (p. 244)
Park assist camera (p. 245)
Park Assist Pilot (PAP)* (p. 249)
The distance covered to the rear of the car is
about 1.5 metres. The acoustic signal for
obstacles behind comes from one of the rear
loudspeakers.
Rear parking assistance is activated when
reverse gear is engaged.
When reversing with e.g. a trailer on the towbar, rear parking assistance is switched off
automatically - otherwise the sensors would
react to the trailer.
The distance covered in front of the car is
about 0.8 metres. The acoustic signal for
obstacles in front comes from one of the front
loudspeakers.
07
Front park assist is active up to
approx. 10 km/h. The lamp in the button is
illuminated in order to indicate that the system is activated. When the speed is below
10 km/h the system is reactivated.
}}
* Option/accessory, for more information, see Introduction.
243
07 Driver support
||
IMPORTANT
When auxiliary lamps are fitted: Remember
that these must not obscure the sensors the auxiliary lamps may then be perceived
as an obstacle.
Related information
•
•
•
•
•
•
•
Park assist syst* (p. 241)
Park assist syst* - cleaning the sensors
(p. 244)
Park assist syst* - function (p. 241)
Park assist syst* - fault indication
Parking assistance is used as an aid to parking. An acoustic signal as well as symbols on
the centre console's display screen indicate
the distance to the detected obstacle.
If the combined instrument panel's
information symbol illuminates with
constant glow and the text message
Park Assist System Service required is
shown then parking assistance is disengaged.
Park assist syst* - fault indication (p. 244)
Park assist syst* - cleaning the
sensors
Parking assistance is used as an aid to parking. An acoustic signal as well as symbols on
the centre console's display screen indicate
the distance to the detected obstacle.
The sensors for parking assistance must be
cleaned regularly to ensure that they work
properly. Clean them with water and car
shampoo.
IMPORTANT
Park assist syst* - backward (p. 243)
Under some circumstances, the parking
sensors can give false warning signals due
to external sound sources which emit the
same ultrasound frequencies as those with
which the system works.
Park assist camera (p. 245)
Park Assist Pilot (PAP)* (p. 249)
Examples of such sources include horns,
wet tyres on asphalt, pneumatic brakes
and exhaust noises from motorcycles etc.
Related information
07
•
•
•
•
•
•
•
244
* Option/accessory, for more information, see Introduction.
Park assist syst* (p. 241)
Park assist syst* - cleaning the sensors
(p. 244)
Park assist syst* - function (p. 241)
Park assist syst* - forward (p. 243)
Park assist syst* - backward (p. 243)
Park assist camera (p. 245)
Park Assist Pilot (PAP)* (p. 249)
Sensor location, front.
07 Driver support
Park assist camera
Function and operation
The parking camera is an auxiliary system and
is activated when the reverse gear is selected.
The camera image is shown on the centre
console's screen.
NOTE
When a towbar is configured with the car's
electrical system, the protrusion of the
towbar is included when the function
measures the parking space.
Sensor location, rear.
NOTE
Dirt, ice and snow covering the sensors
will reduce their function and may prevent
measurement.
Related information
•
•
•
•
•
•
•
Park assist syst* (p. 241)
Park assist syst* - function (p. 241)
Park assist syst* - forward (p. 243)
Park assist syst* - fault indication (p. 244)
Park assist syst* - backward (p. 243)
Park assist camera (p. 245)
Park Assist Pilot (PAP)* (p. 249)
WARNING
•
The parking camera is an aid and can
never replace the responsibilities of
the driver when reversing.
•
The camera has blind spots where
obstacles cannot be detected.
•
Be aware of people and animals near
the car.
Camera location next to the opening handle.
The camera shows what is behind the car
and if something appears from the sides.
The camera shows a wide area behind the
car and part of the bumper and any towbar.
Objects on the screen may appear to tilt
slightly - this is normal.
NOTE
Objects on the display screen may be
closer to the car than they appear to be on
the screen.
07
If another view is active then the parking
camera system takes over automatically and
its camera image is displayed on the screen.
When reverse gear is selected, two unbroken
lines are shown graphically which illustrate
}}
* Option/accessory, for more information, see Introduction.
245
07 Driver support
||
where the car's rear wheels will roll with the
current steering wheel angle - this facilitates
parallel parking, reversing into tight spaces
and for hitching a trailer. The car's approximate external dimensions are illustrated by
means of dashed lines. The park assist lines
can be deactivated - see section Settings
(p. 247).
If the car is also equipped with Parking assistance sensors (p. 241)* then their information
is shown graphically as coloured areas in
order to illustrate the distance to detected
obstacles, see heading "Cars with reversing
sensors" later in the text.
The camera is active approx. 5 seconds after
reverse gear has been disengaged or until the
car's speed exceeds 10 km/h forward or
35 km/h backward.
Light conditions
07
The camera image is adjusted automatically
according to prevailing light conditions.
Because of this, the image may vary slightly
in brightness and quality. Poor light conditions can result in a slightly reduced image
quality.
NOTE
Keep the camera lens clear of dirt, snow
and ice to ensure optimum function. This
is particularly important in poor light.
246
Park assist lines
IMPORTANT
Remember that the display only shows the
area behind the car - so pay attention to
the sides and front of the car when turning
the steering while reversing.
Boundary lines
Examples of how the park assist lines can be displayed for the driver.
The lines on the screen are projected as if
they were at ground level behind the car and
are directly related to steering wheel movement, which shows the driver the path the car
will then take - also when the car is turning.
•
NOTE
Boundary line, free reversing zone
When reversing with a trailer which is
not connected electrically to the car,
the lines on the display show the route
the car will take - not the trailer.
"Wheel tracks"
•
The screen shows no lines when a
trailer is connected electrically to the
car's electrical system.
•
The parking camera is deactivated
automatically when towing a trailer if a
Volvo genuine trailer cable is used.
* Option/accessory, for more information, see Introduction.
Different lines in the system.
The dashed line (1) frames in a zone up to
about 1.5 m back from the bumper. It is also
the limit of the car's most protruding parts,
such as door mirrors and corners - also when
the car is turning.
The wide "wheel tracks" (2) between the side
lines indicate where the wheels will roll and
can extend about 3.2 m back from the
bumper if no obstacle is in the way.
07 Driver support
Cars with reversing sensors*
Park assist camera - settings
Related information
•
•
•
•
Park assist camera - settings (p. 247)
Park assist camera - limitations (p. 249)
Park assist syst* (p. 241)
Park Assist Pilot (PAP)* (p. 249)
Activate switched-off camera
If the camera function is switched off when
reverse gear is selected, it is activated in the
following way:
Coloured areas (x 4 - one per sensor) show distance.
If the car is also equipped with Parking assistance (p. 241) the distance is shown with coloured fields for each sensor that registers an
obstacle.
The colour of the areas changes with
decreasing distance to the obstacle - from
light yellow to yellow, via orange to red.
29
Colour / paint
Distance (metres)
Light yellow
0,7–1,5
Yellow
0,5–0,7
Orange
0,3–0,5
Red
0–0,3
Main source menu29.
1. Give one or two long presses on EXIT to
access the main source menu.
2. Turn to the "Camera" option with TUNE
and press OK/MENU.
3. In the following menu: - Turn to the
desired camera view with TUNE and
press OK/MENU - the screen shows the
current camera view.
See the Sensus Infotainment supplement for more information about the menu system.
07
}}
* Option/accessory, for more information, see Introduction.
247
07 Driver support
||
Options*
Cars with the front camera option have a
CAM button on the climate panel.
1. Press OK/MENU when a camera view is
shown - the screen changes to a menu
with various options.
2. Turn to reach the desired option with
TUNE.
3. Highlight the option by pressing OK/
MENU once and go back out with EXIT.
Towbar
The camera can be used to advantage when
hitching a trailer. A park assist line for the
towbar's intended "trajectory" toward the
trailer can be shown on the screen - exactly
as for the "wheel tracks".
Button location may vary depending on options
for other equipment.
•
07
Press CAM to activate the camera
- the screen shows the current camera
view.
1. Press OK/MENU when a camera view is
shown.
To change view between the reversing camera and front camera:
2. Turn to reach the Tow bar trajectory
guide line option with TUNE.
•
3. Highlight the option by pressing OK/
MENU once and go back out with EXIT.
Press CAM or turn TUNE.
Change setting
The default setting is that the camera is activated when reverse gear is selected.
The settings for the parking camera can be
changed when the screen shows a camera
view:
248
A choice can be made between showing the
"wheel tracks" or the towbar's trajectory
- both options cannot be shown simultaneously.
Zoom
If precise manoeuvring is required then the
camera view can be zoomed in:
•
* Option/accessory, for more information, see Introduction.
Press CAM or turn TUNE - repeated
press/turn changes back to the normal
view.
If more options are available, they are in a
loop - press/turn until the desired camera
view is shown.
Related information
•
•
•
•
Park assist camera (p. 245)
Park assist camera - limitations (p. 249)
Park assist syst* (p. 241)
Park Assist Pilot (PAP)* (p. 249)
07 Driver support
Park assist camera - limitations
NOTE
Bicycle racks or other accessories mounted on the back of the car may obscure
the line of sight of the camera.
To bear in mind
Pay attention to the possibility that, even if it
only looks like a relatively small part of the
image is obscured, it could be a relatively
large sector that is hidden from view. Obstacles could thereby go undetected until they
are very close to the car.
Park Assist Pilot (PAP)*
WARNING
The Park Assist Pilot (PAP – Park Assist Pilot)
helps the driver to park by first checking
whether a space is sufficiently large and then
turning the steering wheel and steering the
car into the space.
PAP does not work in all situations but is
designed merely as a supplementary aid.
The driver always has the final responsibility for driving the vehicle in a safe manner
and for paying attention to the surroundings and other road users approaching or
passing during parking.
The combined instrument panel uses symbols, graphics and text when elements are to
be executed.
Related information
•
Park Assist Pilot (PAP)* - function
(p. 250)
•
Park Assist Pilot (PAP)* - operation
(p. 250)
•
Keep the camera lens free from dirt, ice
and snow.
•
Park Assist Pilot (PAP)* - limitations
(p. 252)
•
Clean the camera lens regularly with lukewarm water and car shampoo - take care
not to scratch the lens.
•
Active Park Assist (PAP)* - symbols and
messages (p. 253)
•
Park assist camera (p. 245)
Related information
•
•
•
•
Park assist camera (p. 245)
Park assist camera - settings (p. 247)
Park assist syst* (p. 241)
Park Assist Pilot (PAP)* (p. 249)
The On/Off button is on the centre console.
NOTE
When a towbar is configured with the car's
electrical system, the protrusion of the
towbar is included when the function
measures the parking space.
* Option/accessory, for more information, see Introduction.
07
249
07 Driver support
Park Assist Pilot (PAP)* - function
Park Assist Pilot (PAP)* - operation
The combined instrument panel uses symbols, graphics and text when elements are to
be executed.
The driver is instructed about how PAP works
by means of simple, clear instructions in the
combined instrument panel - using both
graphics and text graphics and text message
(p. 253).
NOTE
The PAP function measures the space and
turns the steering wheel - the driver's task
is to follow the combined instrument panel's instructions and select the gear
(reverse/forward), control the speed, brake
and stop.
NOTE
Principle for PAP.
PAP can be activated if the following criteria
are met once the engine has been started:
The PAP function parks the car using the following steps:
•
1. The function searches for a parking space
and measures it (A & B (p. 250)). During
measurement, speed must not
exceed 30 km/h.
•
•
The functions ABS30 or ESC31 must not
intervene during an ongoing PAP function
- these can be activated in the event of
e.g. steep and slippery surfaces, see the
sections on Foot brake (p. 288) and Stability system ESC (p. 183) for more information.
Trailers must not be connected to the car.
The speed must be below 50 km/h.
1 - Searching and checking
measurements
2. The car is steered into the space while
reversing (C & D (p. 251)).
3. The car is straightened up in the space by
driving forward and back (E & F (p. 251)).
Related information
•
•
07
Remember that certain steering wheel
positions may obstruct the combined
instrument panel's instructions when you
turn it during the parking manoeuvre.
Park Assist Pilot (PAP)* (p. 249)
Park assist camera (p. 245)
The PAP function searches for a parking
space and checks whether it is big enough.
Proceed as follows:
30
31
250
(Anti-lock Braking System) - Anti-lock braking system.
(Electronic Stability Control) - Stability system.
* Option/accessory, for more information, see Introduction.
07 Driver support
1. Activate PAP by pressing
this button and do not drive
faster than 30 km/h.
2 - Reversing in
2. Keep an eye on the combined instrument
panel and be prepared to stop the car
when the graphics and text message so
request.
3. Stop the car when the graphics and text
so request.
NOTE
PAP searches the area for a parking
space, displays instructions and guides
the car in on its passenger side. But if
required the car can also be parked on the
driver's side of the street:
•
Activate the direction indicator for the
driver's side - the car is then parked
on that side of the street instead.
During the Reversing step, PAP will steer the
car into the parking space. Proceed as follows:
NOTE
•
Keep your hands away from the steering wheel when the PAP function is
activated.
•
Make sure that the steering wheel is
not hindered in any way and can rotate
freely.
•
To achieve optimum results - wait until
the steering wheel is fully turned
before starting to drive backward/
forward.
3 - Straightening up
1. Check that the area behind the car is
clear, then engage reverse gear.
2. Reverse slowly and carefully without
touching the steering wheel - and no
faster than approx. 7 km/h.
3. Keep an eye on the combined instrument
panel and be prepared to stop the car
when the graphics and text message so
request.
When the car has reversed into the parking
space, it must be straightened up and stopped.
07
}}
251
07 Driver support
||
1. Engage first gear or D position, wait until
the steering wheel has been turned, then
drive slowly forwards.
Park Assist Pilot (PAP)* - limitations
The PAP sequence is stopped:
2. Stop the car when the graphics and text
message so request.
•
if the car is driven too quickly - above
7 km/h
3. Engage reverse gear and drive backwards slowly until the graphics and text
message tell you to stop.
•
•
if the driver touches the steering wheel
The function is disengaged automatically
when parking is complete, and the graphics
and text message show that parking is complete. It may be necessary for the driver to
correct the positioning. Only the driver can
determine whether the car is properly parked.
A text message indicates where the PAP
sequence was stopped.
IMPORTANT
The warning distance is shorter when the
sensors are used by Active Park Assist
compared with when Park Assist uses the
sensors.
Related information
•
•
Park Assist Pilot (PAP)* (p. 249)
Park assist camera (p. 245)
07
The driver should bear in mind that the Park
Assist Pilot is an aid – not an infallible, fullyautomatic function. The driver must therefore
be prepared to intervene. There are also
details to bear in mind while parking, e.g.:
•
PAP starts out from the current location
of the parked vehicles - if they are inappropriately parked then the car's tyres
and wheel rims may be damaged against
kerbs.
•
PAP is designed for parking on straight
streets, not sharp curves or bends. For
this reason, make sure the car is parallel
to the parking space when PAP measures
the space.
•
It is not always possible to find parking
spaces on narrow streets since there is
not enough space for manoeuvring. In
such parking situations, it helps the system to drive as close to the side of the
road as possible where you intend to
park.
•
Bear in mind that the front of the car may
swing out towards oncoming traffic while
being parked.
•
Objects situated higher than the detection
areas of the sensors are not included
when calculations are made for the parking manoeuvre. This may cause PAP to
swing into the parking space too early,
NOTE
Dirt, ice and snow covering the sensors
will reduce their function and may prevent
measurement.
IMPORTANT
Under certain circumstances, PAP is
unable to find parking spaces - one reason
for this may be the fact that there is interference with the sensors from external
sound sources which emit the same ultrasound frequencies as those with which the
system works.
Examples of such sources include horns,
wet tyres on asphalt, pneumatic brakes
and exhaust noises from motorcycles etc.
32
33
252
if the ABS32 or ESC33 function is engaged
- e.g. if a wheel loses grip on a slippery
road surface.
To bear in mind
(Anti-lock Braking System) - Anti-lock braking system.
(Electronic Stability Control) - Stability and traction control system.
* Option/accessory, for more information, see Introduction.
07 Driver support
and hence such parking pockets should
be avoided.
•
The driver is responsible for determining
whether the space selected by PAP is
suitable for parking.
•
Use approved tyres34 with the correct tyre
pressure - this affects the ability of PAP
to park the car.
•
Heavy rain or snow may cause the system to measure the parking space incorrectly.
•
Do not use PAP if snow chains or a spare
wheel are fitted.
•
Do not use PAP if loaded objects are protruding from the car.
IMPORTANT
The PAP system's parameters may need
to be updated when changing to another
approved wheel rim size involving changed
tyre circumference. Consult a workshop an authorised Volvo workshop is recommended.
Active Park Assist (PAP)* - symbols
and messages
Maintenance
The combined instrument panel can show different combinations of symbols and text with
varying content - sometimes with a selfexplanatory piece of advice on appropriate
action.
If a message says that the Park Assist Pilot is
disengaged, contact with an authorised Volvo
workshop is recommended.
Related information
The PAP sensors are located in the bumpers35 6 front and 4 rear.
For the PAP function to work correctly, its
sensors must be cleaned (p. 244) regularly
with water and car shampoo - these are the
same sensors as are used by parking assistance (p. 241).
•
•
Park Assist Pilot (PAP)* (p. 249)
Park assist camera (p. 245)
Related information
•
•
Park Assist Pilot (PAP)* (p. 249)
Park assist camera (p. 245)
07
34
35
"Approved tyres" refers to tyres of the same type and make as those fitted new on delivery from the factory.
NOTE: The illustration is schematic - details may differ depending on car model.
* Option/accessory, for more information, see Introduction.
253
07 Driver support
BLIS
Overview
BLIS (Blind Spot Information System) is a
function designed for providing support for
the driver when driving in dense traffic on
roads with several lanes in the same direction.
BLIS is a driver's aid intended to provide a
warning about:
•
•
vehicles in the car's blind spot
quickly approaching vehicles in the left
and right lanes closest to the car.
WARNING
BLIS is a supplementary aid and does not
work in all situations.
Position of the BLIS lamp36.
Indicator lamp
NOTE
The lamp illuminates on the side of the car
where the system has detected the vehicle. If the car is overtaken on both sides at
the same time then both lamps illuminate.
Maintenance
The sensors for the BLIS functions are
located inside the rear wing/bumper on each
corner of the car.
07
36
254
•
BLIS symbol
BLIS is no substitute for a safe driving
style and the use of rearview and door mirrors.
BLIS can never replace the driver's
responsibility and attention - it is always
the driver's responsibility to change lanes
in a safe manner.
Keep this surface clean - also on the left-hand
side.
NOTE: The illustration is schematic - details may vary depending on car model.
* Option/accessory, for more information, see Introduction.
To ensure optimal functionality, the areas
in front of the sensors must be kept
clean.
Related information
•
•
•
BLIS - operation (p. 255)
BLIS and CTA - symbols and messages
(p. 258)
CTA* (p. 256)
07 Driver support
BLIS - operation
BLIS (Blind Spot Information System) is a
function designed for providing support for
the driver when driving in dense traffic on
roads with several lanes in the same direction.
Activate/deactivate BLIS
BLIS is activated when the engine is started.
This is confirmed by the indicator lamps in
the door panels flashing once.
•
Select On or Off at Settings
settings BLIS.
Car
When BLIS is deactivated/activated the lamp
in the button goes out/illuminates and the
combined instrument panel confirms the
change with a text message. The door panel
indicator lamps flash once upon activation.
To extinguish the message:
•
Press the left stalk switch OK button.
or
•
Wait approx. 5 seconds – the message
extinguishes.
The system is designed to react when:
•
•
the vehicle is overtaken by other vehicles
another vehicle is quickly approaching
the vehicle.
When BLIS detects a vehicle in zone 1 or a
quickly approaching vehicle in zone 2, the
door panel BLIS lamp illuminates with a constant glow. If the driver activates the direction
indicator on the same side as the warning in
this situation then the BLIS lamp will change
from a constant glow to flashing with a more
intense light.
WARNING
When BLIS operates
BLIS does not work in sharp bends.
BLIS does not work when the car is being
reversed.
Limitations
•
Dirt, ice and snow covering sensors can
reduce functionality and make it impossible to provide warnings. BLIS cannot
detect hazards if it is covered.
•
Do not affix any objects, tape or labels in
the area of the sensors.
•
BLIS is deactivated when a trailer is connected to the car's electrical system.
Button for activating/deactivating.
The BLIS function can be deactivated/activated by pressing the BLIS button on the
centre console.
Some combinations of the selected equipment leave no vacant space for a button in
the centre console - in which case the function is handled by the car's menu system MY
CAR37:
37
For information on the menu system - MY CAR (p. 108).
Principle for BLIS: 1. Zone in blind spot. 2. Zone
for quickly approaching vehicle.
07
The BLIS function is active at speeds above
approx. 10 km/h.
}}
255
07 Driver support
||
IMPORTANT
Repair of the BLIS and CTA functions'
components or repainting the bumpers
must only be performed by a workshop an authorised Volvo workshop is recommended.
Related information
•
•
BLIS (p. 254)
BLIS and CTA - symbols and messages
(p. 258)
CTA*
•
The BLIS function CTA (Cross Traffic Alert) is
a driver aid intended to warn about crossing
traffic when the car is reversing. CTA is a supplement to BLIS (p. 254).
However, the BLIS function remains activated
after the CTA has been deactivated.
Activate/deactivate CTA
CTA is activated when the engine is started.
This is confirmed by the indicator lamps in
the door panels flashing once.
Search for Cross Traffic Alert under
BLIS and uncheck - the CTA function is
then deactivated.
WARNING
CTA is a supplementary aid and does not
work in all situations.
CTA is no substitute for a safe driving style
and the use of rearview and door mirrors.
CTA can never replace the driver's responsibility and attention - it is always the driver's responsibility to reverse in a safe manner.
When CTA operates
On/Off for parking assistance and CTA sensors.
07
In cars equipped with Parking assistance
(p. 241), the CTA function can be deactivated/activated separately with the parking
assistance On/Off button.
In cars without a button for parking assistance, the CTA function can be operated in
the menu system MY CAR, MY CAR (p. 108),
as follows:
256
* Option/accessory, for more information, see Introduction.
Principle for CTA.
CTA supplements the BLIS function by being
able to see crossing traffic from the side dur-
07 Driver support
ing reversing, such as when reversing out of a
parking space.
vehicle/object that is blocking, at which the
blind sector rapidly decreases.
CTA is primarily designed to detect vehicles.
In favourable conditions, it may also be able
to detect smaller objects, such as cyclists
and pedestrians.
Examples of further limitations:
•
CTA is only active during reversing and is
activated automatically when reverse is
selected at the gearbox.
Dirt, ice and snow covering sensors can
reduce functionality and make it impossible to provide warnings. CTA cannot
detect hazards if it is covered.
•
CTA is deactivated when a trailer is connected to the car’s electrical system.
•
If CTA detects something approaching
from the side, an acoustic warning signal
sounds. The signal comes from either the
left or the right speaker depending on
which direction the approaching object is
coming from.
•
CTA also warns by illuminating the BLIS
lamps.
•
An additional warning is provided in the
form of an illuminated icon in the display
screen's PAS graphics (p. 241).
IMPORTANT
The car is parked deep inside a parking slot.
Blind CTA sector.
Sector where CTA can detect/"see".
Maintenance
The sensors for the BLIS and CTA functions
are located inside the rear wing/bumper on
each corner of the car.
Limitations
CTA does not perform optimally in all situations, but has a certain limitation - for example, the CTA sensors cannot "see" through
other parked vehicles or obstructing objects.
Here are some examples of when CTA's "field
of vision" may be limited from the beginning
and approaching vehicles cannot therefore be
detected until they are very close:
Repair of the BLIS and CTA functions'
components or repainting the bumpers
must only be performed by a workshop an authorised Volvo workshop is recommended.
07
In an angled parking slot CTA can be completely
"blind" on one side.
However, when the driver is slowly reversing
the car, the angle is changed in relation to the
}}
257
07 Driver support
||
BLIS and CTA - symbols and
messages
In situations where the BLIS (Blind Spot
Information System) (p. 254) and CTA (p. 256)
functions fail or are interrupted, the combined
instrument panel may show a symbol, supplemented by an explanatory message. Follow
any recommendation given.
Message examples:
Keep this surface clean - also on the left-hand
side.
•
•
To ensure optimal functionality, the areas
in front of the sensors must be kept
clean.
Do not affix any objects, tape or labels in
the area of the sensors.
Related information
•
•
BLIS (p. 254)
BLIS and CTA - symbols and messages
(p. 258)
Message
Specification
CTA OFF
CTA has been deactivated
manually. BLIS is active.
BLIS and
CTA OFF
Trailer
attached
BLIS and CTA are temporarily disabled because a
trailer is connected to the
car’s electrical system.
BLIS and
CTA Service required
BLIS and CTA are not
working.
07
•
Visit a workshop if the
message remains - an
authorised Volvo workshop is recommended.
A text message can be acknowledged by
briefly pressing the OK button on the direction indicator stalk.
258
* Option/accessory, for more information, see Introduction.
Related information
•
•
BLIS (p. 254)
CTA* (p. 256)
07 Driver support
Speed related power steering
Type approval - radar system
Speed related power steering causes the
steering wheel force to increase with the
speed of the car in order to give the driver
enhanced sensitivity.
Type approval for the radar system can be
read in the table.
On motorways the steering feels firmer.
Steering is light and requires no extra effort
when parking and at low speed.
The driver can choose between three different levels of steering force for road responsiveness or steering sensitivity in the menu
system MY CAR, MY CAR (p. 108):
•
Country/
Area
Singapore
IDA: Infocomm Development
Authority of Singapore.
Brazil
Once there, search for Steering wheel
force and select Low, Medium or High.
This menu is not accessible when the car is
moving.
Europe
Delphi Electronics &
Safety hereby declares that
L2C0038TR and L2C0049TR
are in compliance with the
essential requirements and
other relevant provisions of
Directive 1999/5/EC. This declaration of conformity may, if
necessary, be consulted with
Delphi Electronics & Safety /
One Corporate Center /
Kokomo, Indiana 46904-9005
USA.
NOTE
In certain situations the power steering
may become too hot and then needs to be
temporarily cooled - during this time the
power steering operates with reduced
power and turning the steering wheel may
then be perceived to be slightly heavier.
In parallel with the temporarily reduced
steering assistance the combined instrument panel shows a message.
Related information
•
MY CAR (p. 108)
07
Related information
•
Radar sensor (p. 208)
259
STARTING AND DRIVING
08 Starting and driving
Alcolock*
Alcolock* - functions and operation
Alcolock1
The function of the
is to prevent the
car from being driven by individuals under the
influence of alcohol. Before the engine can be
started the driver must take a breath test that
verifies that he/she is not under the influence
of alcohol. Alcolock calibration takes place in
accordance with each market's limit value in
force for driving legally.
Functions
WARNING
Indicator
lamp (4)
Battery status
Green flashing
Charging in progress
Green
Fully charged
Yellow
Semi-charged
Red
Discharged - fit the charger
in the holder or connect the
power supply cable from
the glovebox.
The Alcolock is an aid and does not
exempt the driver from responsibility. It is
always the responsibility of the driver to be
sober and to drive the car safely.
NOTE
Nozzle for breath test.
Related information
•
Alcolock* - functions and operation
(p. 261)
•
•
Alcolock* - storage (p. 262)
•
•
Alcolock* - to bear in mind (p. 264)
Alcolock* - before starting the engine
(p. 262)
Alcolock* - symbols and messages
(p. 265)
Store the Alcolock in its holder. This will
keep the built-in battery fully charged and
the Alcolock is activated automatically
when the car is opened.
Switch.
Transmission button.
Lamp for battery status.
Related information
Lamp for result of breath test.
Lamp indicates ready for breath test.
Operation
Battery
Alcolock indicator lamp (4) shows battery status:
•
•
•
Alcolock* (p. 261)
•
•
Alcolock* - to bear in mind (p. 264)
Alcolock* - storage (p. 262)
Alcolock* - before starting the engine
(p. 262)
Alcolock* - symbols and messages
(p. 265)
08
1
Also called Alcoguard.
* Option/accessory, for more information, see Introduction.
261
08 Starting and driving
Alcolock* - storage
•
Store the Alcolock in its holder. Release the
handheld unit by depressing it slightly into its
holder and releasing it - it then springs out
and can be removed from the holder.
Alcolock* - symbols and messages
(p. 265)
Alcolock* - before starting the engine
The Alcolock is activated automatically and is
then ready for use when the car is opened.
Nozzle for breath test.
Handheld unit storage and charging station.
Switch.
•
Replace the handheld unit in the holder
by pushing it in until it engages.
Transmission button.
•
Store the handheld unit in the holder this provides it with the best protection
and keeps its batteries fully charged.
Lamp for battery status.
Related information
08
262
•
•
Alcolock* (p. 261)
•
Alcolock* - before starting the engine
(p. 262)
•
Alcolock* - to bear in mind (p. 264)
Alcolock* - functions and operation
(p. 261)
* Option/accessory, for more information, see Introduction.
Lamp for result of breath test.
Lamp indicates ready for breath test.
1. When the indicator lamp (6) is green the
Alcolock is ready for use.
2. Withdraw the Alcolock from its holder. If
the Alcolock is outside the car when it is
unlocked then it must first be activated
with the switch (2).
3. Fold up the nozzle (1), take a deep breath
and blow with an even pressure until a
08 Starting and driving
"click" is heard after approx. 5 seconds.
The result will be one of the alternatives in
the following table Result after breath
test.
•
•
•
Result after breath test
4. If no message is shown then the transmission to the car may have failed - in
which case, press the button (3) to transmit the result to the car manually.
5. Fold down the nozzle and refit the Alcolock in its holder.
6. Start the engine following an approved
breath test within 5 minutes - otherwise it
must be repeated.
Indicator lamp
(5) + Display
text
Specification
Green lamp +
Alcoguard
Approved test
Start the engine - no
alcohol content measured.
Yellow lamp +
Alcoguard
Approved test
Engine starting possible - measured alcohol
content is above
0.1 promille but below
the limit value in
forceA.
Red lamp + Disapproved test
Wait 1 minute
to try again
Engine starting not
possible - measured
alcohol content is
above the limit value in
forceA.
A
Alcolock* - storage (p. 262)
Alcolock* - to bear in mind (p. 264)
Alcolock* - symbols and messages
(p. 265)
Limit values vary from country to country. Find out what
applies in your country. See also Alcolock* - to bear in
mind (p. 264)
NOTE
After a completed period of driving, the
engine can be restarted within 30 minutes
without a new breath test.
Related information
•
•
08
Alcolock* (p. 261)
Alcolock* - functions and operation
(p. 261)
* Option/accessory, for more information, see Introduction.
263
08 Starting and driving
Alcolock* - to bear in mind
In order to obtain correct function and as
accurate a measurement result as possible:
•
Avoid eating or drinking
approx. 5 minutes before the breath test.
•
Avoid excess windscreen washing - the
alcohol in the washer fluid may result in
an incorrect measurement result.
Change of driver
on its own after approx. 2 minutes but then
reappears each time the engine is started only recalibration at a workshop2 can clear
the message permanently.
Calibration and service
30 days before recalibration is necessary the
combined instrument panel shows the message Alcoguard Calibration required See
manual. If calibration is not carried out within
these 30 days then normal engine starting will
be blocked - only starting with the Bypass
function will then be possible, see the following heading "Emergency situation".
08
264
NOTE
The colder the weather the longer it takes
before the Alcolock is ready for use:
Temperature (ºC)
Maximum heating time (seconds)
+10 to +85
10
-5 to +10
60
-40 to -5
180
At temperatures below -20 ºC or above
+60 ºC the Alcolock requires additional power
supply. The combined instrument panel
shows Alcoguard Please insert power
cable. In which case, connect the power
supply cable from the glovebox and wait until
indicator lamp (6) is green.
In extremely cold weather the heating time
can be reduced by taking the Alcolock
indoors.
The message can be cleared by pressing the
send button (3) once. Otherwise it goes out
2
In the event of an emergency situation or the
Alcolock is out of order, it is possible to
bypass the Alcolock in order to drive the car.
Cold or hot weather
In order to ensure that a new breath test is
carried out in the event of a change of driver depress the switch (2) and the send button (3)
simultaneously for approx. 3 seconds. At
which point the car returns to start inhibition
mode and a new approved breath test is
required before starting the engine.
The Alcolock must be checked and calibrated
at a workshop2 every 12 months.
Emergency situation
An authorised Volvo workshop is recommended.
* Option/accessory, for more information, see Introduction.
All activation with bypass is logged and
saved in a memory; see Recording data
(p. 18).
After the bypass function has been activated
the combined instrument panel shows
Alcoguard Bypass enabled the whole time
while driving and can only be reset by a workshop2.
The Bypass function can be tested without
the error message being logged - in which
case, carry out all the steps without starting
the car. The error message is cleared when
the car is locked.
When the Alcolock is installed, either the
Bypass or Emergency function is selected as
the bypassing option. This setting can be
changed afterwards at a workshop2.
Activating the Bypass function
•
Depress and hold the left-hand stalk
switch OK button and the button for hazard warning flashers simultaneously for
approx. 5 seconds - the combined instrument panel first shows Bypass activated
08 Starting and driving
Please wait for 1 minute and then
Alcoguard Bypass enabled - after
which the engine can be started.
This function can be activated several times.
The error message shown during driving can
only be cleared at a workshop2.
Activating the Emergency function
•
Depress and hold the left-hand stalk
switch OK button and the button for hazard warning flashers simultaneously for
approx. 5 seconds - the combined instrument panel shows Alcoguard Bypass
enabled and the engine can be started.
This function can be used once, after which a
reset must be made at a workshop2.
Related information
•
•
Alcolock* (p. 261)
•
•
Alcolock* - storage (p. 262)
•
Alcolock* - symbols and messages
(p. 265)
Alcolock* - functions and operation
(p. 261)
Alcolock* - before starting the engine
(p. 262)
Alcolock* - symbols and messages
In addition to the previously described messages related to how the alcolock works
before starting the engine (p. 262) the following can also be displayed:
Display text
Meaning/Action
Alcoguard
Restart possible
The engine has been
switched off for less
than 30 minutes engine starting possible
without new test.
Alcoguard
Service
required
Contact a workshopA.
Alcoguard No
signal
received
Transmission failed send manually with button (3) or take a new
breath test.
Alcoguard
Please try
again
Test failed - take a new
breath test.
Alcoguard
Please blow
longer
Blowing too short - blow
for longer.
Display text
Meaning/Action
Alcoguard
Please blow
softer
Blowing too hard - blow
more gently.
Alcoguard
Please blow
harder
Blowing too weak blow harder.
Alcoguard
preheating
Please wait
Heating not finished wait for text Alcoguard
Please blow for 5 seconds.
A
An authorised Volvo workshop is recommended.
Related information
•
•
Alcolock* (p. 261)
•
•
Alcolock* - storage (p. 262)
•
Alcolock* - to bear in mind (p. 264)
Alcolock* - functions and operation
(p. 261)
Alcolock* - before starting the engine
(p. 262)
08
2
An authorised Volvo workshop is recommended.
* Option/accessory, for more information, see Introduction.
265
08 Starting and driving
Starting the engine
The engine is started and switched off using
the remote control key and the START/STOP
ENGINE button.
IMPORTANT
Do not press in the remote control key
incorrectly turned - Hold the end with the
detachable key blade; see Detachable key
blade - detaching/attaching (p. 164)
1. Insert the remote control key in the ignition switch and press it in to its end position. Note that if the car is equipped with
Alcolock* then a breath test must first be
approved before the engine can be
started. For more information on the
Alcolock, see Alcolock* (p. 261).
Ignition switch with remote control key extracted/inserted. and START/STOP ENGINE button.
2. Hold the clutch pedal fully depressed3.
(For cars with automatic gearbox Depress the brake pedal.)
3. Press the START/STOP ENGINE button
and then release it.
The starter motor works until the engine is
started or until its overheating protection triggers.
IMPORTANT
If the engine fails to start after 3 attempts wait for 3 minutes before making a further
attempt. Starting capacity increases if the
battery is allowed to recover.
NOTE
The idling speed can be noticeably higher
than normal for certain engine types during
cold starting. This is done in order that the
emissions system can reach normal operating temperature as quickly as possible,
which minimises exhaust emissions and
protects the environment.
Keyless Drive*
Follow steps 2–3 for keyless (p. 166) starting
of petrol and diesel engines.
NOTE
A prerequisite for the engine to start is that
one of the car's remote control keys with
the Keyless drive function is in the passenger compartment or cargo area.
WARNING
Never remove the remote control key from
the car while driving or during towing.
08
3
266
WARNING
Always remove the remote control key
from the ignition switch when leaving the
car, and make sure that the key position is
0 - in particular if there are children in the
car. For information on how this works,
see Key positions (p. 75).
If the car is moving then it is enough to press the START/STOP ENGINE button to start the car.
* Option/accessory, for more information, see Introduction.
08 Starting and driving
Related information
•
Key positions (p. 75)
Switching off the engine
Steering lock
The engine is switched off using the START/
STOP ENGINE button.
The steering lock makes steering difficult if
the car is e.g. taken unlawfully.
To switch off the engine:
Function
•
Press the START/STOP ENGINE button
- the engine stops.
•
If the car has an automatic gearbox and
the gear selector is not in a position P or
if the car is moving - Press twice or hold
the START/STOP ENGINE button
depressed until the engine stops.
Related information
•
Key positions (p. 75)
•
The steering lock locks when the driver's
door is opened after the engine has been
switched off.
•
The steering lock unlocks when the
remote control key is in the ignition
switch4 and the START/STOP ENGINE
button is depressed.
A mechanical noise can be perceived when
the steering lock unlocks or locks.
Related information
•
•
•
Starting the engine (p. 266)
Key positions (p. 75)
Steering wheel (p. 82)
08
4
Cars with Keyless drive only need to have a remote control key inside the passenger compartment.
267
08 Starting and driving
Jump starting
If the starter battery (p. 369) is discharged
then the car can be started with current from
another battery.
4. Connect one of the red jump lead's
clamps to the donor battery's positive
terminal (1).
11. Start the engine in the car with the discharged battery.
IMPORTANT
IMPORTANT
Connect the start cable carefully to avoid
short circuits with other components in the
engine compartment.
5. Open the clips on the front cover of the
battery in your car and remove the cover.
6. Connect the red jump lead's other clamp
onto the car's positive terminal (2).
Do not use the connections when attempting to start, as there is a risk of sparking.
12. Remove the jump leads in reverse order first the black and then the red.
> Make sure that none of the black jump
lead's clamps comes into contact with
the battery's positive terminal or the
clamp connected to the red jump lead!
7. Connect one of the black jump lead's
clamps to the donor battery's negative
terminal (3).
When jump starting the car, the following
steps are recommended to avoid short circuits or other damage:
8. Connect the other clamp to a grounding
point, e.g. right-hand engine mounting at
the top, the outer screw head (4).
1. Set the car's electrical system in key
position 0, see Key positions (p. 75).
9. Check that the jump lead clamps are
affixed securely so that there are no
sparks during the starting procedure.
2. Check that the donor battery has a voltage of 12 V.
3. If the donor battery is installed in another
car - switch off the donor car's engine
and make sure that the two cars do not
touch each other.
08
268
WARNING
10. Start the engine of the "donor car" and
allow it to run a few minutes at a speed
slightly higher than idle
approx. 1500 rpm.
•
The battery can generate oxyhydrogen
gas, which is highly explosive. A spark
can be formed if a jump lead is connected incorrectly, and this can be
enough for the battery to explode.
•
The battery contains sulphuric acid,
which can cause serious burns.
•
If sulphuric acid comes into contact
with eyes, skin or clothing, flush with
large quantities of water. If acid
splashes into the eyes - seek medical
attention immediately.
Related information
•
Starting the engine (p. 266)
08 Starting and driving
Gearboxes
Manual gearbox
Reverse gear inhibitor
There are two main types of gearbox - Manual
and Automatic.
The function of the gearbox is to change the
gear ratio depending on speed and power
requirements.
The reverse gear inhibitor hinders the possibility of mistakenly attempting to engage
reverse gear during normal forward travel.
•
•
Manual gearbox (p. 269)
Automatic gearbox - Geartronic (p. 270)
and Powershift (p. 274)
IMPORTANT
To prevent damage to any drive system
components, the working temperature of
the gearbox is checked. If there is a risk of
overheating, a warning symbol in the combined instrument panel lights up and a text
message is shown. Follow the recommendation given in the text message.
•
Follow the gearing pattern printed on the
gear lever and start from neutral position,
N before moving it to R position.
•
Engage reverse gear only when the car is
stationary.
Related information
•
Gearboxes (p. 269)
Gearing pattern.
The 6-speed box is available in two versions reverse gear position differs between them.
Look at the actual gearshift pattern imprinted
on the gear lever.
•
Depress the clutch pedal fully during
each gear change.
•
Take your foot off the clutch pedal
between gear changes.
WARNING
Always apply the parking brake when
parking on a slope - leaving the car in gear
is not sufficient to hold the car in all situations.
08
269
08 Starting and driving
Gear shift indicator*
Automatic gearbox
The gear shift indicator notifies the driver
when it is appropriate to engage the next
higher or lower gear in order to obtain the
lowest possible fuel consumption.
An essential detail in connection with environmental driving is to drive in the right gear and
to change gear in plenty of time.
An indicator is available as an aid on certain
variants - GSI (Gear Shift Indicator) - which
notifies the driver when it is appropriate to
engage the next higher or lower gear in order
to obtain the lowest possible fuel consumption. However, taking into consideration characteristics such as performance and vibration-free running, it may be advantageous to
change gear at a higher engine speed.
Combined instrument panel "Digital" with
gear shift indicator.
The framed number indicates the current
gear.
With "Analogue" combined
instrument panel, the gear
positions and indicator
arrows are displayed in its
centre.
Manual gearbox
Gear shift indicator for manual gearbox. Only one
marker is illuminated at a
time - it is illuminated in the
centre only during normal
driving.
When gearing up/down as recommended, the
upper one is illuminated at "+" or the lower at
"-", marked red in the illustration.
Related information
•
•
08
5
270
Automatic gearbox - Geartronic*
An automatic gearbox with Geartronic differs
from an Automatic gearbox - Powershift
(p. 274), in that it has a hydraulic torque converter that transfers power from engine to
gearbox. It has two different gear modes Automatic and Manual.
The gear lever's gearshift pattern varies depending on engine option.
* Option/accessory, for more information, see Introduction.
Manual gearbox (p. 269)
Automatic gearbox - Geartronic* (p. 270)
D: Automatic gear positions. +/–: Manual gear
positions. S: Sport mode*.5
The combined instrument panel shows the
position of the gear selector using the following indications: P, R, N, D, S*, 1, 2, 3 etc.
08 Starting and driving
Gear positions
Automatic gear positions are
indicated on the right of the
combined instrument panel.
(Only one marker is illuminated at a time - the one
showing the current gear
selector position.)
Symbol "S" for Sport mode is ORANGE when
the mode is active.
P – Parking position
Select P when starting the engine or when
the car is parked.
•
In order to be able to move the gear
selector from P position, the brake pedal
must first be depressed firmly.
The gearbox is mechanically blocked when
the P position is engaged. Apply the parking
brake as well, as a precaution - , see Parking
brake (p. 290).
NOTE
The gear selector must be in P position to
allow the car to be locked and alarmed.
IMPORTANT
The car must be stationary when position P is selected.
WARNING
Always apply the parking brake when
parking on a slope - the automatic transmission in P is not sufficient to hold the car
in all situations.
sponds to the gear that has just been
selected.
•
Move the lever forwards towards + (plus)
to change up a gear and release the
lever, which returns to its neutral position
between "+" and "–".
R – Reverse
or
The car must be stationary when position R is
selected.
•
N – Neutral
The manual gearshift mode "+/-" can be
selected at any time while driving.
No gear is engaged and the engine can be
started. Apply the parking brake if the car is
stationary with the gear selector in position N.
D – Drive
D is the normal driving position. Shifting up
and down takes place automatically based on
the level of acceleration and speed. The car
must be stationary when the gear selector is
moved to position D from position R.
Geartronic – Manual gear positions (+/-)
The driver can also change gear manually
using the Geartronic automatic gearbox. The
car engine-brakes when the accelerator pedal
is released.
The manual gear position is reached by moving the lever to the side from position D to the
end position at "+/-". The combined instrument panel's symbol "+/-" changes colour
from WHITE to ORANGE and the digits 1, 2, 3
etc. are displayed in a box which corre-
Pull the lever back towards "–" (minus) to
change down a gear and release it.
Geartronic automatically shifts down if the
driver allows the speed to decrease lower
than a level suitable for the selected gear, in
order to avoid jerking and stalling.
To return to automatic driving mode:
•
Move the lever to the side to the end
position at D.
NOTE
f the gearbox has a Sport programme then
the gearbox will only become manual after
the lever has been moved forwards or
backwards in its "+/-" position. The combined instrument panel then shifts the indication from S to show which of the gears
1, 2, 3 etc. is engaged.
Paddles*
08
As a supplement to manual gear changing
with the gear selector there are also controls
}}
* Option/accessory, for more information, see Introduction.
271
08 Starting and driving
||
located on the steering wheel, so-called
"paddles".
To be able to change gear with the steering
wheel paddles they must first be activated.
This is by means of pulling one of the paddles
toward the steering wheel - the combined
instrument panel then changes indication
from "D" to a figure, which indicates the current gear.
To then change gear one step:
•
Pull one of the paddles backwards towards the steering wheel - and release.
A gear change occurs at each pull of the paddle provided that the engine speed does not
leave the permitted range.
After each gear change the combined instrument panel changes figure to show the current gear.
NOTE
Automatic deactivation
If the steering wheel paddles are not used
then they are deactivated after a short time
- this is indicated when the combined
instrument panel switches indication, from
the figure for the current gear back to "D".
The exception is during engine braking then the paddles are activated as long as
engine braking is in progress.
Manual deactivation
The steering wheel paddle shifters can
also be deactivated manually:
•
Both steering wheel "paddles".
Pull both paddles toward the steering
wheel and hold until the combined
instrument panel changes character
from the figure for the current gear to
"D".
"-": Selects the next lower gear.
"+": Selects the next higher gear.
08
6
272
The paddles can also be used with the gear
selector in Sport mode* - then the paddles
are constantly activated without being deactivated.
If the car has Sport mode* then "S" is shown first.
* Option/accessory, for more information, see Introduction.
Geartronic - Sport mode (S)
The Sport programme provides
sportier characteristics and allows
higher engine speed for the gears.
At the same time it responds more
quickly to acceleration. During active driving,
the use of a lower gear is prioritised, leading
to a delayed upshift.
To activate Sport mode:
•
Move the gear selector to the side from D
position to the end position at "+S–" - the
combined instrument panel changes indication from D to S.
Sport mode can be selected at any time while
driving.
Geartronic - Winter mode
It can be easier to pull away on slippery roads
if 3rd gear is engaged manually.
1. Depress the brake pedal and move the
gear selector from D position to the end
position at "+/–" - the combined instrument panel shifts the indication from D to
the figure 16.
2. Scroll up to gear 3 by pushing the lever
forward towards "+" (plus) twice - the
combined instrument panel shifts the
indication from 1 to 3.
3. Release the brake and accelerate carefully.
08 Starting and driving
The gearbox "winter mode" means that the
car moves off with a lower engine speed and
reduced engine power on the drive wheels.
Kick-down
When the accelerator pedal is pressed all the
way to the floor (beyond the position normally
regarded as full acceleration) a lower gear is
immediately engaged. This is known as kickdown.
Towing
If the car has to be towed - see important
information in the section Towing (p. 308).
Related information
•
Transmission fluid - grade and volume
(p. 403)
•
•
Gearboxes (p. 269)
Automatic gearbox - Powershift* (p. 274)
If the accelerator is released from the kickdown position, the gearbox automatically
changes up.
Kick-down is used when maximum acceleration is needed, such as for overtaking.
Safety function
To prevent overrevving the engine, the gearbox control program has a protective downshift inhibitor which prevents the kick-down
function.
Geartronic does not permit downshifting/
kick-down which would result in an engine
speed high enough to damage the engine.
Nothing happens if the driver still tries to shift
down in this way at high engine speed – the
original gear remains engaged.
When kick-down is activated the car can
change one or more gears at a time depending on engine speed. The car changes up
when the engine reaches its maximum speed
in order to prevent damage to the engine.
08
* Option/accessory, for more information, see Introduction.
273
08 Starting and driving
Automatic gearbox - Powershift*
Towing
The Powershift automatic gearbox transmits
the motive force from the engine to the drive
wheels with double mechanical clutch discs,
as opposed to Geartronic which instead uses
a hydraulic torque converter.
The model with Powershift transmission
should not be towed as it is dependent on the
engine running in order to receive sufficient
lubrication. If towing (p. 308) still has to take
place, the route must be as short as possible
and then at very low speed.
In the event of uncertainty as to whether the
car is equipped with Powershift or Geartronic
transmission, this can be verified by checking
the designation on the gearbox label under
the bonnet, Type designations (p. 392). The
designation ”MPS6” means that it is
Powershift transmission - otherwise it is
Geartronic automatic transmission.
See also important information in section
Towing (p. 308).
D: Automatic gear positions. +/–: Manual gear
positions. S: Sport mode*.7
Powershift transmission operates in the same
way and has similar controls and functions as
the Geartronic automatic transmission.
One exception is "Geartronic - Winter mode"
(p. 270):
•
08
7
274
Powershift enables driving away on a
slippery road surface if 2nd gear is
engaged manually - instead of 3rd gear
with Geartronic.
To bear in mind
The transmission's double clutch has overload protection that is activated if it becomes
too hot, e.g. if the car is held stationary with
the accelerator pedal on an uphill gradient for
a long time.
Overheated transmission causes the car to
shake and vibrate, and the warning symbol
illuminates and the combined instrument
panel shows a message. The transmission
can also overheat during slow driving in
The gear lever's gearshift pattern varies depending on engine option.
* Option/accessory, for more information, see Introduction.
queues (10 km/h or slower) on an uphill gradient, or with a trailer hitched. The transmission
cools down when the car is stationary, with
foot brake depressed and the engine running
at idling speed.
Overheating during slow driving in queues
can be avoided by driving in stages:
•
Stop the car and wait with your foot on
the brake pedal until there is a moderate
distance to the traffic ahead, drive forward a short distance, and then wait
another moment with your foot on the
brake pedal.
IMPORTANT
Use the foot brake to hold the car stationary on an uphill gradient - do not hold the
car with the accelerator pedal. The gearbox could then overheat.
Text message and action
In some situations the combined instrument
panel may show a text message at the same
time as a symbol is illuminated.
08 Starting and driving
Symbol
A
Message
Driving characteristics
Action
Transmission hot Brake to
hold
Difficulty in maintaining even speed
at constant engine speed.
Transmission overheated. Keep the car stationary using the
foot brake.A
Transmission hot Park
safely Let engine run
Significant pulling in the car's traction.
Transmission overheated. Park the car immediately in a safe
manner.A
Transmission cooling Let
engine run
No drive due to overheated gearbox.
Transmission overheated. For fastest cooling: Run the
engine at idling speed with the gear lever in the N or P position until the message clears.
For fastest cooling: run the engine at idling speed with the gear lever in the N or P position, until the message clears.
The table shows three steps with an
increased degree of seriousness should the
transmission become too hot. In parallel with
the text message, the driver is also advised
that the car's electronics are temporarily
changing the driving characteristics. Follow
the instructions in the text message where
appropriate.
WARNING
If a warning symbol combined with the text
Transmission hot Park safely Let
engine run is ignored then the heat in the
gearbox may become so high that the
power transmission between engine and
gearbox is temporarily halted in order to
prevent the clutch from malfunctioning the car then loses drive and is stationary
until gearbox temperature has cooled to
an acceptable level.
NOTE
The examples in the table are no indication
of the car being defective, but show that a
safety function has been activated with a
view to preventing damage to any of the
car's components.
For more possible text messages with their
respective proposals for solutions concerning
automatic gearbox, see Messages (p. 106).
A text message extinguishes automatically
after the action has been carried out or after
one press on the indicator stalk OK button.
08
Related information
•
Automatic gearbox - Geartronic* (p. 270)
* Option/accessory, for more information, see Introduction.
275
08 Starting and driving
•
Gear selector inhibitor
There are two different types of gear selector
inhibitor - mechanical and automatic.
Keep your foot on the brake pedal when
moving the gear selector to another position.
Deactivate automatic gear selector
inhibitor
Electric gear inhibitor – Shiftlock
Parking position (P)
Mechanical gear selector inhibitor
To be able to move the gear selector from P
to other gear positions, the brake pedal must
be depressed and the remote control key
must be in position II.
G021351
Shiftlock – Neutral (N)
The gear selector can be moved forward and
back freely between N and D. Other positions
are locked with a latch that is released with
the inhibitor button on the gear selector.
If the gear selector is in the N position and
the car has been stationary for at least 3 seconds (irrespective of whether the engine is
running) then the gear selector is locked.
To be able to move the gear selector from N
to another gear position the brake pedal must
be depressed and the remote control key
must be in key position II (p. 75).
If the car cannot be driven, e.g. due to a flat
battery, the gear selector must be moved
from the P position so that the car can be
moved.
Lift out the contoured insert in the compartment behind the centre console and
locate a spring-loaded button in the bottom of the compartment.
With the inhibitor button depressed the lever
can be moved forwards or backwards
between P, R, N and D.
Press and hold the button.
Move the gear selector from the P position and release the button.
Automatic gear selector inhibitor
08
276
The automatic gearbox has special safety
systems:
4. Refit the storage compartment insert.
Parking position (P)
Related information
Stationary car with engine running:
* Option/accessory, for more information, see Introduction.
•
•
Automatic gearbox - Geartronic* (p. 270)
Automatic gearbox - Powershift* (p. 274)
08 Starting and driving
Hill start assist (HSA)*
Start/Stop*
The foot brake can be released before setting
off or reversing uphill - the HSA (Hill Start
Assist) function means that the car does not
roll backwards.
Some engine and gearbox combinations
come fitted with a Start/Stop function which
engages in the event of e.g. stationary traffic
or waiting at traffic lights - the engine is then
switched off temporarily and restarts automatically when the journey is due to continue.
The function means that the pedal pressure in
the brake system remains for several seconds
while the driver's foot is moved from brake
pedal to accelerator pedal.
The temporary braking effect releases after
several seconds or when the driver accelerates.
Related information
•
Starting the engine (p. 266)
conscious way of driving the car by means of
being able to allow the engine to stop automatically, whenever appropriate.
Manual or Automatic
Note that there are differences in the
Start/Stop function depending on whether the
gearbox is manual or automatic.
Environmental care is one of Volvo Car Corporation's core values and it influences all of
our operations. This target orientation has
resulted in several separate energy-saving
functions of which Start/Stop is one, all with
the collective task of reducing fuel consumption, which in turn helps to reduce exhaust
emissions.
•
Start/Stop* - function and operation
(p. 278)
•
•
•
Starting the engine (p. 266)
General information on Start/Stop
•
Start/Stop* - the engine auto-starts
(p. 281)
•
Start/Stop* - the engine does not stop
(p. 279)
•
Start/Stop* - involuntary stop manual
gearbox (p. 282)
•
Start/Stop* - symbols and messages
(p. 284)
•
Battery - Start/Stop (p. 372)
Related information
Start/Stop* - settings (p. 283)
Start/Stop* - the engine does not autostart (p. 282)
The engine is switched off - it becomes quieter
and cleaner...
08
The Start/Stop function gives the driver the
opportunity for a more active environmentally
* Option/accessory, for more information, see Introduction.
277
08 Starting and driving
Start/Stop* - function and operation
Conditions
The Start/Stop function is activated automatically when the engine is started with the key.
The Start/Stop function is
activated automatically when
the engine is started with the
key. The driver is alerted to
the function by means of the
symbol for the On/Off button
illuminating in the combined
instrument panel and the
lamp in the On/Off button
illuminating.
All of the car's normal systems such as lighting, radio, etc. work as normal even with an
engine that has stopped automatically,
except that some equipment may have the
function temporarily reduced, e.g. the climate
control system's fan speed or extremely high
volume on the audio system.
Auto-stopping the engine
The following is required for the engine to
auto-stop:
A
M/A
Auto-starting the engine
A
Declutch, set the gear lever in neutral position and release the clutch
pedal - the engine stops automatically.
M
Stop the car with the foot brake
and then keep your foot on the
pedal - the engine stops automatically.
A
If the ECO function is activated then the engine may
auto-stop before the car is
completely stationary.
The combined instrument panel's
symbols for the Start/Stop function
illuminate as verification and
reminder that the engine has stopped automatically.
* Option/accessory, for more information, see Introduction.
With the gear lever in neutral position:
M
2. Engage a suitable gear and
drive.
Release the foot pressure on the
foot brake - the engine starts automatically and the journey can continue.
A
Maintain foot pressure on the foot
brake and depress the accelerator
pedal - the engine auto-starts.
A
The following option is also available on a downhill gradient:
M+
A
•
A
278
M/
AA
1. Depress the clutch pedal or
press the accelerator pedal the engine starts.
M = Manual gearbox, A = Automatic gearbox.
08
Conditions
Release the foot brake and let
the car move off - the engine
starts automatically when the
speed exceeds normal walking
pace.
M = Manual gearbox, A = Automatic gearbox.
08 Starting and driving
Deactivating the Start/Stop function
In certain situations, it may
advisable to temporarily
switch off the automatic
Start/Stop function - this is
carried out with a push of
this button.
Disengaged function is indicated by
the combined instrument panel's
Start/Stop symbols and the button's
lamp extinguishing.
The Start/Stop function is disengaged until it
is reactivated with the button or until the next
time the engine is started with the key.
Start assistance HSA
The foot brake can also be released on an
uphill slope to auto-start the engine - the HSA
(p. 277) (Hill Start Assist) function prevents
the car from rolling backwards.
HSA means that the pressure in the brake
system remains temporarily available while
the driver's foot is moved from the brake
pedal to the accelerator pedal for driving off
with the engine having stopped automatically.
The temporary braking effect releases after a
couple of seconds or when the driver accelerates.
Related information
•
•
•
•
Start/Stop* (p. 277)
Starting the engine (p. 266)
Start/Stop* - settings (p. 283)
Start/Stop* - the engine does not autostart (p. 282)
•
Start/Stop* - the engine auto-starts
(p. 281)
•
Start/Stop* - the engine does not stop
(p. 279)
•
Start/Stop* - involuntary stop manual
gearbox (p. 282)
•
•
Start/Stop* - the engine does not stop
Although the Start/Stop function is activated,
the engine does not always stop automatically.
The engine does not auto-stop if:
Conditions
M/A
the car has not first achieved
approx. 8 km/h after a key start or
the last auto-stop.
M+
A
Start/Stop* - symbols and messages
(p. 284)
the driver has opened the seatbelt's buckle.
M+
A
Battery - Start/Stop (p. 372)
the capacity of the starter battery
is below the minimum permissible
level.
M+
A
the engine does not have normal
operating temperature.
M+
A
ambient temperature is around
freezing point or above
approx. 30 °C.
M+
A
the windscreen's electric heating
is activated.
M+
A
A
08
}}
* Option/accessory, for more information, see Introduction.
279
08 Starting and driving
||
08
280
Conditions
M/A
Conditions
the environment in the passenger
compartment differs from the preset valuesB - indicated by the ventilation fan running at a high
speed.
M+
A
the gearbox does not have normal
operating temperature.
A
A
the car is reversed.
M+
A
the starter battery's temperature is
below freezing point or too high.
M+
A
the atmospheric air pressure is
less than equivalent to
1500-2500 metres above sea level
- the current air pressure varies
with the prevailing weather conditions.
A
the driver makes greater steering
wheel movements.
M+
A
adaptive cruise control Queue
Assist is activated.
A
the exhaust system's particulate
filter is full - the temporarily disengaged Start/Stop function is reactivated as soon as an automatic
cleaning cycle has been performed (see Diesel particle filter
(DPF) (p. 299)).
M+
A
the gear selector is moved out of
the D position to S positionD or
"+/-".
the road is very steep.
M+
A
a trailer is connected electrically to
the car’s electrical system.
M+
A
the bonnet has been
A
openedC.
A
B
C
D
M/A
A
M = Manual gearbox, A = Automatic gearbox.
Car with ECC.
With certain engines only.
Sport mode.
Related information
M+
A
•
•
Start/Stop* (p. 277)
Start/Stop* - function and operation
(p. 278)
•
•
•
Starting the engine (p. 266)
•
Start/Stop* - the engine auto-starts
(p. 281)
* Option/accessory, for more information, see Introduction.
Start/Stop* - settings (p. 283)
Start/Stop* - the engine does not autostart (p. 282)
•
Start/Stop* - involuntary stop manual
gearbox (p. 282)
•
Start/Stop* - symbols and messages
(p. 284)
•
Battery - Start/Stop (p. 372)
08 Starting and driving
Start/Stop* - the engine auto-starts
Conditions
An auto-stopped engine may restart in certain
cases without the driver having decided that
the journey should continue.
In the following cases the engine also starts
automatically if the driver has not depressed
the clutch pedal (manual gearbox) or takes
his/her foot off the brake pedal (automatic
gearbox):
Conditions
M/AA
Misting forms on the windows.
M+A
The environment in the passenger
compartment deviates from the
preset valuesB.
M+A
There is a temporarily high current
take-off or starter battery capacity
drops below the lowest permissible level.
M+A
Repeated pumping of the brake
pedal.
M+A
The bonnet is openedC.
M+A
The car starts to roll, or there is a
small increase in speed if the car
auto-stopped without being completely stationary.
M+A
M/AA
The driver's seatbelt buckle is
opened with the gear selector in D
or N position.
A
Steering wheel movementsC.
•
•
Start/Stop* - settings (p. 283)
Start/Stop* - the engine does not autostart (p. 282)
•
Start/Stop* - the engine does not stop
(p. 279)
A
•
The gear selector is moved out of
the D position to S positionD, R or
"+/-".
A
Start/Stop* - involuntary stop manual
gearbox (p. 282)
•
Start/Stop* - symbols and messages
(p. 284)
The driver's door is opened with
the gear selector in D position - a
"ping" sound and text message
inform that the Start/Stop function
is active.
A
•
•
A
B
C
D
Battery - Start/Stop (p. 372)
Start/Stop* (p. 277)
M = Manual gearbox, A = Automatic gearbox.
Car with ECC.
With certain engines only.
Sport mode.
WARNING
Do not open the bonnet when the engine
has stopped automatically - the engine
may suddenly start automatically. First
switch off the engine as normal using the
START/STOP ENGINE button before
opening the bonnet.
Related information
•
Start/Stop* - function and operation
(p. 278)
•
Starting the engine (p. 266)
08
* Option/accessory, for more information, see Introduction.
281
08 Starting and driving
Start/Stop* - the engine does not
auto-start
The engine does not always auto-start after
having auto-stopped.
In the following cases the engine does not
auto-start after having auto-stopped:
Conditions
M/
AA
A gear is engaged without
declutching - a display text
prompts the driver to set the gear
lever in neutral position in order to
enable automatic starting.
M
The driver is unrestrained, the gear
selector is in P position and the
driver’s door is open - a normal
engine start must take place.
A
A
•
Start/Stop* - involuntary stop manual
gearbox (p. 282)
•
Start/Stop* - involuntary stop manual
gearbox
Start/Stop* - symbols and messages
(p. 284)
•
Battery - Start/Stop (p. 372)
In the event that a start-up fails and the
engine stops, proceed in accordance with the
below:
08
282
2. In certain cases the gear lever must be
set in neutral position. The combined
instrument panel then shows the text Put
gear in neutral.
Related information
•
•
M = Manual gearbox, A = Automatic gearbox.
Related information
•
•
1. Depress the clutch pedal again - the
engine starts automatically.
Start/Stop* (p. 277)
Start/Stop* - function and operation
(p. 278)
•
•
•
Starting the engine (p. 266)
•
Start/Stop* - the engine does not stop
(p. 279)
Start/Stop* - settings (p. 283)
Start/Stop* - the engine auto-starts
(p. 281)
* Option/accessory, for more information, see Introduction.
Start/Stop* (p. 277)
Start/Stop* - function and operation
(p. 278)
•
•
•
Starting the engine (p. 266)
•
Start/Stop* - the engine auto-starts
(p. 281)
•
Start/Stop* - the engine does not stop
(p. 279)
•
Start/Stop* - symbols and messages
(p. 284)
•
Battery - Start/Stop (p. 372)
Start/Stop* - settings (p. 283)
Start/Stop* - the engine does not autostart (p. 282)
08 Starting and driving
Start/Stop* - settings
The car's menu system MY CAR (p. 108) contains information on Volvo's Start-Stop system, as well as recommendations for energysaving driving techniques.
•
Start/Stop* - symbols and messages
(p. 284)
•
Battery - Start/Stop (p. 372)
Related information
•
•
Start/Stop* (p. 277)
Start/Stop* - function and operation
(p. 278)
•
•
Starting the engine (p. 266)
•
Start/Stop* - the engine auto-starts
(p. 281)
•
Start/Stop* - the engine does not stop
(p. 279)
•
Start/Stop* - involuntary stop manual
gearbox (p. 282)
Start/Stop* - the engine does not autostart (p. 282)
08
* Option/accessory, for more information, see Introduction.
283
08 Starting and driving
Start/Stop* - symbols and messages
Text message
The Start/Stop function can show text messages in the combined instrument panel.
In combination with this indicator
lamp the Start/Stop function may
display text messages in the combined instrument panel for certain situations.
Symbol
Message
Info/Action
M/AA
Auto Start/Stop Service
required
Start/Stop is not operational. Contact a workshop - an authorised Volvo workshop is recommended.
M+A
Autostart Engine running +
acoustic signal
Activated if the driver's door is opened with auto-stopped engine and the gear selector in
D position.
A
Press start button
The engine will not start automatically - start the engine as normal with the START/STOP
ENGINE button.
M+A
Depress clutch pedal to
start
The engine is ready to auto-start - waiting for the clutch pedal to be depressed.
M
Depress brake and clutch
pedals to start
The engine is ready to auto-start - waiting for the brake or clutch pedal to be depressed.
M
Put gear in neutral to start
Gear is engaged without declutching - disengage and set the gear lever in neutral position.
M
08
284
For some of them there is a recommended
action that should be performed. The following table shows some examples.
* Option/accessory, for more information, see Introduction.
08 Starting and driving
Symbol
A
Message
Info/Action
Select P or N to start
Start/Stop has been deactivated - move the gear selector to N or P position and start the
engine as normal with the START/STOP ENGINE button.
A
Press start button
The engine will not start automatically - start the engine as normal with the START/STOP
ENGINE button and the gear selector in P or N.
A
M/AA
M = Manual gearbox, A = Automatic gearbox.
If a message does not go out following completion of the action then a workshop should
be contacted - an authorised Volvo workshop
is recommended.
Related information
•
•
Start/Stop* (p. 277)
Start/Stop* - function and operation
(p. 278)
•
•
•
Starting the engine (p. 266)
•
Start/Stop* - the engine auto-starts
(p. 281)
•
Start/Stop* - the engine does not stop
(p. 279)
•
Start/Stop* - involuntary stop manual
gearbox (p. 282)
•
Battery - Start/Stop (p. 372)
Start/Stop* - settings (p. 283)
Start/Stop* - the engine does not autostart (p. 282)
08
* Option/accessory, for more information, see Introduction.
285
08 Starting and driving
ECO*
NOTE
ECO8
is an innovative Volvo function for automatic-gearbox cars, capable of reducing fuel
consumption by up to 5%, depending on the
driver's driving style. The function gives the
driver the option of a more active environmentally conscious way of driving.
General
The following are changed
upon activation of the ECO
function:
When the ECO function is activated, several parameters in the climate control system's settings are changed, and several
electricity consumer functions are
reduced. Certain settings can be reset
manually, but full functionality is only
restored by deactivating the ECO function.
ECO - Operation
el's ECO symbol and the ECO- button's lamp
illuminating when the function is activated.
ECO function On or Off
Disengaged ECO function is
indicated by the combined
instrument panel ECO symbol and the ECO button lamp
extinguishing. The function is
then switched off until it is
reactivated with the ECO
button.
Eco Coast - Function
•
•
Gearbox gearshift points.
Engine management and response from
the accelerator pedal.
•
Start/Stop function - the engine can also
auto-stop before the car has stopped
down to being completely stationary.
•
The Eco Coast function is activated engine braking ceases.
•
Climate control system settings - some
electricity consumers are deactivated or
operate at reduced power.
08
8
286
The Eco Coast subfunction means in practice
that engine braking is deactivated, meaning in
turn that the car's kinetic energy is used to
coast for longer distances. When the driver
releases the accelerator pedal the gearbox is
automatically disengaged from the engine
whose speed is reduced to idling speed with
minimum consumption.
ECO On/Off
ECO symbol
The ECO function is deactivated when the
engine is switched off, and must therefore be
activated after each time the engine is
started. There are exceptions for certain
engines. However, it is easily verified by
means of both the combined instrument pan-
Not possible on the V40 CROSS COUNTRY AWD.
* Option/accessory, for more information, see Introduction.
This function is intended for use in the event
of an anticipated reduction in speed, e.g. to
coast forward to an intersection or a red light.
Eco Coast enables proactive driving where
the driver can use the so-called "Pulse &
Glide" technique and a minimum of braking.
Combination On and Off
A combination of Eco Coast and temporarily
deactivated ECO function can also collec-
08 Starting and driving
tively contribute to reduced consumption.
Accordingly:
•
on steep downhill gradients - to be able
to use engine braking.
•
•
before an imminent overtaking manoeuvre - in order to be able to complete it in
the safest possible way.
Active Eco Coast: Long coasting without
engine braking = Low consumption
and
•
Deactivated ECO function: Short coasting
with engine braking = Minimum consumption.
NOTE
However, to achieve optimal low fuel consumption, Eco Coast in combination with
short coasting distances should generally
be avoided.
Activating Eco Coast
Deactivating Eco Coast and returning to
engine braking can be performed as follows:
•
•
Press the ECO button.
•
Change gear with the steering wheel paddle shifters.
•
Actuate the accelerator or brake pedal.
Move the gear lever to manual "S+/-"
position.
Eco Coast - Limitations
The function is not available if:
The function is activated when the accelerator pedal is fully released, in combination with
the following parameters:
•
•
cruise control is activated
•
•
•
•
manual gear changing is performed with
the steering wheel paddle shifters*
•
engine and/or gearbox are not at normal
operating temperature.
•
the gear selector is moved from D- to "S
+/-" position
•
speed is outside the range of
approx. 65-140 km/h
•
ECO button activated
Gear selector in D position
Speed within the range of
approx. 65-140 km/h
The road's downhill gradient is not
steeper than approx. 6%.
Deactivate Eco Coast
In certain situations it may be desirable to
deactivate the Eco Coast function. Examples
of such situations include:
More information and settings
the road's downhill gradient is steeper
than approx. 6%
The car's menu system MY CAR contains
further information on the ECO concept - see
the section MY CAR (p. 108).
Related information
•
General information on climate control
(p. 121)
08
287
08 Starting and driving
Foot brake
The foot brake is used to reduce the car's
speed while driving.
The car is equipped with two brake circuits. If
a brake circuit is damaged then the brake
pedal will engage deeper and a higher pressure on the pedal is needed to produce the
normal braking effect.
The driver's brake pedal pressure is assisted
by a brake servo.
WARNING
The brake servo only works when the
engine is running.
If the brake is used when the engine is
switched off then the pedal will feel stiff and
more force must be used to brake the car.
In very hilly terrain or when driving with a
heavy load the brakes can be relieved by
using engine braking. Engine braking is most
efficiently used if the same gear is used
downhill as up.
For more general information on heavy loads
on the car, Engine oil - adverse driving conditions (p. 399).
08
288
Cleaning the brake discs
Coatings of dirt and water on the brake discs
may result in delayed brake function. This
delay is minimised by cleaning the brake linings.
Manual cleaning is advisable with wet road
surfaces, prior to long-stay parking and after
the car has been washed. Carry this out by
braking gently during a short period while en
route.
Maintenance
To keep the car as safe and reliable as possible, follow the Volvo service intervals as
specified in the Service and Warranty Booklet.
IMPORTANT
The wear on the brake system's components must be checked regularly.
Contact a workshop for information about
the procedure or engage a workshop to
carry out the inspection - an authorised
Volvo workshop is recommended.
Symbols in the combined instrument
panel
Symbol
Specification
Constant glow – Check the
brake fluid level. If the level is
low, fill with brake fluid and
check for the cause of the
brake fluid loss.
Constant glow for 2 seconds
when the engine is started –
automatic function check.
WARNING
If
and
illuminate at the same
time, there may be a fault in the brake system.
If the level in the brake fluid reservoir is
normal at this stage, drive carefully to the
nearest workshop and have the brake system checked - an authorised Volvo workshop is recommended.
If the brake fluid is below the MIN level in
the brake fluid reservoir, do not drive further before topping up the brake fluid.
The reason for the loss of brake fluid must
be investigated.
08 Starting and driving
Related information
•
•
Parking brake (p. 290)
Foot brake - emergency brake lights and
automatic hazard warning flashers
(p. 289)
•
Foot brake - emergency brake assistance
(p. 290)
•
Foot brake - anti-lock braking system
(p. 289)
Foot brake - anti-lock braking system
The anti-lock braking system, ABS (Anti-lock
Braking System), prevents the wheels from
locking up during braking.
The function allows the steering ability to be
maintained, and it is easier to swerve to avoid
a hazard for example. Vibration may be felt in
the brake pedal when this is engaged and this
is normal.
A short test of the ABS system is made automatically after the engine has been started
when the driver releases the brake pedal. A
further automatic test of the ABS system may
be made when the car reaches 10 km/h. The
test may be experienced as pulses in the
brake pedal.
Related information
•
•
•
•
Foot brake (p. 288)
Parking brake (p. 290)
Foot brake - emergency brake lights
and automatic hazard warning
flashers
Emergency brake lights are activated to alert
vehicles behind about sudden braking. The
function means that the brake light flashes
instead of - as in normal braking - shining with
a constant glow.
Emergency brake lights are activated at
speeds above 50 km/h if the ABS system is
working and/or in the event of sudden braking. After the car's speed has been slowed
below 10 km/h the brake light returns from
flashing to the normal constant glow - while
at the same time the Hazard warning flashers
are activated, and they flash until the driver
accelerates the car to at least 20 km/h or they
are deactivated with their button.
Related information
Foot brake - emergency brake lights and
automatic hazard warning flashers
(p. 289)
•
•
•
Foot brake - emergency brake assistance
(p. 290)
•
Foot brake (p. 288)
Parking brake (p. 290)
Foot brake - emergency brake assistance
(p. 290)
Foot brake - anti-lock braking system
(p. 289)
08
289
08 Starting and driving
Foot brake - emergency brake
assistance
Emergency brake assistance EBA (Emergency
Brake Assist) helps to increase the braking
force and so reduce the braking distance.
EBA detects the driver's braking style and
increases the braking force when necessary.
The brake force can be reinforced up to the
level when the ABS system is engaged. The
EBA function is interrupted when the pressure
on the brake pedal is reduced.
Parking brake
The parking brake holds the car stationary,
when the driver's seat is empty, by mechanically locking/blocking two wheels.
2. Pull the lever firmly.
> The combined instrument panel warning symbol comes on.
NOTE
WARNING
Always apply the parking brake when
parking on a slope - leaving the car in
gear, or in P if it has automatic transmission, is not sufficient to hold the car in all
situations.
NOTE
- The combined instrument panel's
warning symbol illuminates regardless of
whether the parking brake is applied
slightly or fully.
3. Release the foot brake pedal and make
sure that the car is at a standstill position.
4. If the vehicle moves then the parking
brake lever must be applied at least a little more firmly.
When EBA is activated the brake pedal
lowers slightly more than usual, depress
(hold) the brake pedal as long as necessary. If the brake pedal is released then all
braking ceases.
•
Related information
•
•
•
•
When parking the vehicle, always engage
1st gear (for manual gearbox) or put the
gear selector in position P (for automatic
gearbox).
Foot brake (p. 288)
Parking on a hill
Parking brake (p. 290)
If the car is parked facing uphill:
Foot brake - emergency brake lights and
automatic hazard warning flashers
(p. 289)
Foot brake - anti-lock braking system
(p. 289)
Combined instrument panel warning symbol.
Applying the parking brake
1. Press the foot brake pedal down firmly.
•
Turn the wheels away from the kerb.
If the car is parked facing downhill:
•
Turn the wheels towards the kerb.
Disengaging the parking brake
1. Press the foot brake pedal down firmly.
08
290
08 Starting and driving
2. Pull the lever up slightly, press the button,
release the lever and release the button.
> The combined instrument panel warning symbol goes off.
Driving in water
If the driver forgets to release the parking
brake – in addition to the illuminated warning
lamp – a pinging sound combined with a
message in the combined instrument panel
alerts the driver of this when the car's speed
exceeds 10 km/h.
The car can be driven through water at a
maximum depth of 25 cm at a maximum
speed of 10 km/h. Extra caution should be
exercised when passing through flowing
water.
Related information
•
Foot brake (p. 288)
IMPORTANT
Fording means that the car is driven through a
water-covered roadway. Fording must be carried out with great caution.
Engine damage can occur if water enters
the air filter.
In depths greater than 25 cm, water could
enter the transmission. This reduces the
lubricating ability of the oils and shortens
the service life of these systems.
Damage to any component, engine, transmission, turbocharger, differential or its
internal components caused by flooding,
hydrostatic locking or oil shortage, is not
covered by the warranty.
During driving in water, maintain a low speed
and do not stop the car. When the water has
been passed, depress the brake pedal lightly
and check that full brake function is achieved.
Water and mud for example can make the
brake linings wet resulting in delayed brake
function.
•
Clean the electric contacts of the electric
engine block heater and trailer coupling
after driving in water and mud.
•
Do not let the car stand with water over
the sills for any long period of time - this
could cause electrical malfunctions.
In the event of the engine stalling in water,
do not try restart - tow the car from the
water to a workshop - an authorised Volvo
workshop is recommended. Risk of engine
breakdown.
Related information
•
•
Recovery (p. 310)
Towing (p. 308)
08
291
08 Starting and driving
Overheating
Under special conditions, for example hard
driving in hilly terrain and hot climate, there is
a risk that the engine and drive system may
overheat - in particular with a heavy load.
For information about overheating when driving with a trailer, see Driving with a trailer
(p. 300).
08
292
•
Remove any auxiliary lamps from in front
of the grille when driving in hot climates.
•
If the temperature in the engine's cooling
system is too high then a warning symbol
is illuminated and a text message High
engine temperature Stop safely is
shown in the combined instrument panel's information display - stop the car in a
safe way and allow the engine to run at
idling speed for several minutes in order
to cool down.
•
If the text message High engine
temperature Turn off engine or Engine
coolant level low Stop safely is shown
then the engine must be switched off
after stopping the car.
•
In the event of overheating in the gearbox
a built-in protection function is activated,
which is indicated in the combined instrument panel with a warning symbol and
the text message Transmission hot
Reduce speed or Transmission hot
Stop safely Wait for cooling - follow the
recommendation given and lower the
speed and stop the car in a safe way and
allow the engine to run at idling speed for
a few minutes in order to allow the gearbox to cool down.
•
If the car overheats, the air conditioning
may be switched off temporarily.
•
Do not turn the engine off immediately
you stop after a hard drive.
Driving with open tailgate
When driving with the tailgate open, toxic
exhaust fumes can be sucked into the car
through the cargo area.
WARNING
Do not drive with an open tailgate! Toxic
exhaust fumes could be drawn into the car
through the cargo area.
NOTE
It is normal for the engine's cooling fan to
operate for a time after the engine has
been switched off.
Related information
•
Driving with a trailer - manual gearbox
(p. 302)
•
Driving with a trailer - automatic gearbox
(p. 302)
Related information
•
Loading (p. 148)
08 Starting and driving
Overload - starter battery
Before a long journey
Winter driving
The electrical functions in the car load the
starter battery to varying degrees. Avoid using
the key position II when the engine is
switched off. Instead use the I mode - which
uses less power, see Key positions - functions
at different levels (p. 76).
Before a long journey, it makes good sense to
go through the following points:
For winter driving it is important to perform
certain checks in order to ensure that the car
can be driven safely.
Also, be aware of different accessories that
load the electrical system. Do not use functions which use a lot of power when the
engine is switched off. Examples of such
functions are:
•
•
•
•
ventilation fan
headlamps
windscreen wiper
audio system (high volume).
•
Check that the engine is working normally
and that fuel consumption (p. 408) is normal.
•
Make sure that there are no leaks (fuel, oil
or other fluid).
•
•
Check all bulbs and tyre tread depths.
To bear in mind:
Check the following in particular before the
cold season:
•
The engine coolant (p. 402) must contain
at least 50% glycol. This mixture protects
the engine against frost erosion down to
approximately –35 °C. To achieve optimum antifreeze protection, different types
of glycol must not be mixed.
•
The fuel tank must be kept filled to prevent condensation.
•
Engine oil viscosity is important. Oils with
lower viscosity (thinner oils) facilitate starting in cold weather and also reduce fuel
consumption while the engine is cold. For
more information on suitable oils, see
Engine oil - adverse driving conditions
(p. 399).
Carrying a warning triangle (p. 323) is a
legal requirement in certain countries.
Related information
•
•
•
Engine oil - checking and filling (p. 354)
Spare wheel* (p. 317)
Lamp replacement - general (p. 359)
If the battery voltage is low the information
display shows the text Low battery charge
Power save mode. The energy-saving function then shuts down certain functions or
reduces certain functions such as the ventilation fan and/or audio system.
–
In which case, charge the starter battery
by starting the engine and then running it
for at least 15 minutes - battery charging
is more effective during driving than running the engine at idling speed while stationary.
IMPORTANT
Low viscosity oil must not be used for hard
driving or in hot weather.
•
The condition of the battery and charge
level must be inspected. Cold weather
Related information
•
08
Starter battery - general (p. 369)
}}
* Option/accessory, for more information, see Introduction.
293
08 Starting and driving
||
places great demands on the battery and
its capacity is reduced by the cold.
•
Use washer fluid (p. 369) to avoid ice
forming in the washer fluid reservoir.
To achieve optimum roadholding Volvo recommends using winter tyres on all wheels if
there is a risk of snow or ice.
Fuel filler flap - Opening/closing
Fuel filler flap - manual opening
The fuel filler flap can be opened/closed as
follows:
The fuel filler flap can be opened manually
when it cannot be opened from outside.
Opening/closing the fuel filler flap
NOTE
The use of winter tyres is a legal requirement in certain countries. Studded tyres
are not permitted in all countries.
Slippery driving conditions
Practise driving on slippery surfaces under
controlled conditions to learn how the car
reacts.
Open/remove the side hatch in the cargo
area (same side as fuel filler flap).
Open the fuel filler flap by slightly pressing in the rear part of the hatch.
Carefully pull the line back in a straight
line. The flap can now be opened from
outside.
Take out the flap.
Close the flap after fuelling.
For a description of locking and unlocking the
fuel filler flap, see Locking/unlocking - fuel
filler flap (p. 175). The fuel filler flap's lock
logic also follows the locking or unlocking of
the Keyless system and the central locking
system.
08
294
Related information
•
Filling up with fuel (p. 295)
IMPORTANT
Pull the wire gently - minimal force is
required to disengage the hatch lock.
Related information
•
•
Locking/unlocking - fuel filler flap (p. 175)
Filling up with fuel (p. 295)
08 Starting and driving
Filling up with fuel
NOTE
The fuel tank is fitted with a coverless fuel
filler system. Filling is carried out as follows:
Avoid spilling by waiting approximately
5-8 seconds before carefully removing the
nozzle once refuelling is complete.
Related information
•
Filling with fuel - with a fuel can (p. 299)
Fuel - handling
Fuel of a lower quality than that recommended by Volvo must not be used as engine
power and fuel consumption is negatively
affected.
WARNING
Always avoid inhaling fuel vapour and fuel
splashing in the eyes.
In the event of fuel in the eyes, remove any
contact lenses and rinse the eyes in plenty
of water for at least 15 minutes and seek
medical attention.
•
Open the fuel filler flap (p. 294). See also
Fuel filler flap - manual opening (p. 294).
•
Insert the pump nozzle in the fuel filler
opening. Take care to insert the nozzle
properly into the filler pipe. The filler pipe
consists of two opening covers. The nozzle must be pushed past both covers
before refuelling is started.
•
Do not overfill the tank but fill until the
pump nozzle cuts out.
NOTE
Excess fuel in the tank can overflow in hot
weather.
Never swallow fuel. Fuels such as petrol
and diesel are highly toxic and could
cause permanent injury or be fatal if swallowed. Seek medical attention immediately
if fuel has been swallowed.
WARNING
Fuel which spills onto the ground can be
ignited.
Switch off the fuel-driven heater before
starting to refuel.
Never carry an activated mobile phone
when refuelling. The ring signal could
cause spark build-up and ignite petrol
fumes, leading to fire and injury.
08
}}
295
08 Starting and driving
||
IMPORTANT
Mixtures of various fuel types or use of
fuels which are not recommended will
invalidate Volvo's guarantees and any supplementary service agreements; this is
applicable to all engines.
NOTE
Extreme weather conditions, driving with a
trailer or driving at high altitudes in combination with fuel grade are factors that
could affect the car's performance.
Related information
•
Economical driving (p. 300)
Fuel - petrol
Petrol is used as fuel.
Petrol must fulfil the EN 228 standard. Most
engines can be run with octane ratings of 95
and 98 RON. A lower octane rating such as
RON 91 and 92 should only be used in
exceptional cases.
•
•
95 RON can be used for normal driving.
98 RON is recommended for optimum
performance and minimum fuel consumption.
When driving in temperatures above +38 °C,
fuel with the highest possible octane rating is
recommended for optimum performance and
fuel economy.
IMPORTANT
08
296
•
Use only unleaded petrol to avoid
damaging the catalytic converter.
•
Fuel that contains up to 10 volume-%
ethanol is permitted.
•
Fuel containing metallic additives must
not be used.
•
Do not use any additives which have
not been recommended by Volvo.
Alcohols-ethanol
•
EN228 E10 petrol
(max 10 percent by volume ethanol) is
approved for use.
•
Ethanol higher than E10
(max 10 percent by volume ethanol) is not
permitted, e.g. E85.
Related information
•
•
•
Economical driving (p. 300)
Fuel - handling (p. 295)
Filling up with fuel (p. 295)
08 Starting and driving
Fuel - diesel
Diesel is used as fuel.
Only use diesel fuel from well-known producers. Never use fuel of dubious quality. Diesel
fuel should fulfil the EN 590 or JIS K2204
standards. Diesel engines are sensitive to
contaminants in the fuel, such as excessively
high volumes of sulphur particles for example.
At low temperatures (-6 °C to -40 °C), a paraffin precipitate may form in the diesel fuel,
which may lead to ignition problems. Special
diesel fuel designed for low temperatures
around freezing point is available from the
major oil companies. This fuel is less viscous
at low temperatures and reduces the risk of
paraffin precipitate.
The risk of condensation in the fuel tank is
reduced if the tank is kept well filled. When
refuelling, check that the area around the fuel
filler pipe is clean. Avoid spilling fuel onto the
paintwork. Wash off any spillage with detergent and water.
IMPORTANT
Diesel fuel must:
•
fulfil the EN 590 and/or SS 155435
standards
•
have a sulphur content not exceeding
10 mg/kg
•
have a maximum of 7 vol % FAME
(Fatty Acid Methyl Ester).
IMPORTANT
Diesel type fuels that must not be used:
•
•
•
•
Special additives
1. Insert the remote control key in the ignition switch and push it in to the end position, see Key positions (p. 75).
2. Press the START button without
depressing the brake and/or clutch pedal.
3. Wait approx. one minute.
4. To start the engine: Depress the brake
and/or clutch pedal and then press the
START button again.
Marine diesel fuel
NOTE
Heating oil
FAME9
(Fatty Acid Methyl Ester) and
vegetable oil.
These fuels do not fulfil the requirements in
accordance with Volvo recommendations
and generate increased wear and engine
damage that is not covered by the Volvo
warranty.
Empty tank
The design of the fuel system in a diesel
engine means that if the vehicle runs out of
fuel, the tank may need to be vented in the
workshop in order to restart the engine after
fuelling.
9
Once the engine has stopped due to fuel
starvation, the fuel system needs a few
moments to carry out a check. Do this before
starting the engine, once the fuel tank has
been filled with diesel:
Diesel fuel may contain a certain amount of FAME, but further amounts must not be added.
Before filling with fuel in the event of fuel
shortage:
•
Stop the car on as flat/level ground as
possible - if the car is tilting there is a
risk of air pockets in the fuel supply.
Draining condensation from the fuel
filter
The fuel filter separates condensation from
the fuel. Condensation can disrupt engine
operation.
The fuel filter must be drained at the intervals
specified in the Service and Warranty Booklet
08
}}
297
08 Starting and driving
||
or if you suspect that the car has been filled
with contaminated fuel, see Volvo service
programme (p. 346).
IMPORTANT
Certain special additives remove the water
separation in the fuel filter.
Related information
•
•
•
Diesel particle filter (DPF) (p. 299)
Fuel - handling (p. 295)
Economical driving (p. 300)
Catalytic converters
The purpose of the catalytic converters is to
purify exhaust gases. They are located close
to the engine so that operating temperature is
reached quickly.
The catalytic converters consist of a monolith
(ceramic or metal) with channels. The channel
walls are lined with a thin layer of platinum/
rhodium/palladium. These metals act as catalysts, i.e. they participate in and accelerate a
chemical reaction without being used up
themselves.
Lambda-sondTM oxygen sensor
The Lambda-sond is part of a control system
intended to reduce emissions and improve
fuel economy. For more information, see Fuel
consumption and CO2 emissions (p. 408).
An oxygen sensor monitors the oxygen content of the exhaust gases leaving the engine.
This value is fed into an electronic system
that continuously controls the injectors. The
ratio of fuel to air directed to the engine is
continuously adjusted. These adjustments
create optimal conditions for efficient combustion, and together with the three-way catalytic converter reduce harmful emissions
(hydrocarbons, carbon monoxide and nitrous
oxides).
08
Related information
•
•
298
Economical driving (p. 300)
Fuel - petrol (p. 296)
•
Fuel - diesel (p. 297)
08 Starting and driving
Filling with fuel - with a fuel can
Diesel particle filter (DPF)
When filling with fuel (p. 295) from a fuel can,
use the funnel located under the floor hatch in
the cargo area.
Diesel cars are equipped with a particle filter,
which results in more efficient emission control.
IMPORTANT
Statutory provisions relating to storage of
reserve fuel cans in cars vary from country
to country. Check what does apply.
Take care to insert the funnel properly into
the filler pipe. The filler pipe consists of two
opening covers. The funnel must be pushed
past both covers before filling is started.
Related information
•
•
Locking/unlocking - fuel filler flap (p. 175)
Fuel filler flap - manual opening (p. 294)
motorway. The car should then be driven for
approximately 20 minutes more.
NOTE
The following may arise during regeneration:
The particles in the exhaust gases are collected in the filter during normal driving. Socalled "regeneration" is started in order to
burn away the particles and empty the filter.
This requires the engine to have reached normal operating temperature.
Filter regeneration takes place automatically
and normally takes 10-20 minutes. It may
take a little longer at a low average speed.
Fuel consumption may increase slightly during regeneration.
Regeneration in cold weather
If the car is frequently driven short distances
in cold weather then the engine does not
reach normal operating temperature. This
means that regeneration of the diesel particle
filter does not take place and the filter is not
emptied.
When the filter has become approximately
80% full of particles, a yellow warning triangle
is shown in the combined instrument panel,
and the message Soot filter full See manual
is shown in the information display.
Start regeneration of the filter by driving the
car until the engine reaches normal operating
temperature, preferably on a main road or
•
a smaller reduction of engine power
may be noticed temporarily
•
fuel consumption may increase temporarily
•
a smell of burning may arise.
When regeneration is complete the warning
text is cleared automatically.
Use the parking heater* in cold weather so
that the engine reaches normal operating
temperature more quickly.
IMPORTANT
If the filter is completely filled with particles, it may be difficult to start the engine
and the filter is non-functional. Then there
is a risk that the filter will need to be
replaced.
Related information
•
•
Fuel - diesel (p. 297)
Economical driving (p. 300)
* Option/accessory, for more information, see Introduction.
08
299
08 Starting and driving
Economical driving
Driving economically means driving smoothly
while thinking ahead and adjusting your driving style and speed to the prevailing conditions.
•
Drive with the correct air pressure in the
tyres and check this regularly - select
ECO tyre pressure for best results, see
Tyres - approved tyre pressures (p. 412).
•
Choice of tyres can affect fuel consumption - seek advice on suitable tyres from a
dealer.
•
Use the ECO Guide* (p. 65) which indicates how fuel-efficiently the car is being
driven.
•
•
For lowest fuel consumption, activate
ECO* (p. 286)10 which can further reduce
fuel consumption.
Remove unnecessary items from the car the greater the load the higher the fuel
consumption.
•
•
Do not use winter tyres when the winter
season is over.
Use engine braking to slow down, when it
can take place without risk to other road
users.
•
•
Drive in the highest gear possible, adapted to the current traffic situation and
road - lower engine speeds result in lower
fuel consumption. Use the gear shift indicator (p. 270)11.
A roof load and ski box increase air resistance, leading to higher fuel consumption
- remove the load carriers when not in
use.
•
Avoid driving with open windows.
•
Avoid sudden unnecessary acceleration
and heavy braking.
•
High speed results in increased fuel consumption - the wind resistance increases
with speed.
•
Do not run the engine to operating temperature at idling speed, but rather drive
with a light load as soon as possible - a
cold engine consumes more fuel than a
warm one.
For more information, see Volvo Cars' environmental philosophy (p. 21) and Fuel consumption and CO2 emissions (p. 408).
WARNING
Never switch off the engine while moving,
such as downhill, this deactivates important systems such as the power steering
and brake servo.
08
10
11
300
Automatic gearbox
Manual gearbox
* Option/accessory, for more information, see Introduction.
Driving with a trailer
When driving with a trailer there are a number
of important points to think about regarding
e.g. the towing bracket, the trailer and how
the load is positioned in the trailer.
Payload depends on the car's kerb weight.
The total of the weight of the passengers and
all accessories, e.g. towbar, reduces the car's
payload by a corresponding weight. For more
detailed information, see Weights (p. 395).
If the towing bracket is mounted by Volvo,
then the car is delivered with the necessary
equipment for driving with a trailer.
•
The car's towing bracket must be of an
approved type.
•
If the towbar is retrofitted, check with
your Volvo dealer that the car is fully
equipped for driving with a trailer.
•
Distribute the load on the trailer so that
the weight on the towing bracket complies with the specified maximum towball
load.
•
Increase the tyre pressure to the recommended pressure for a full load. For tyre
pressure label location, see Tyres - air
pressure (p. 322).
•
The engine is loaded more heavily than
usual when driving with a trailer.
08 Starting and driving
•
•
•
Do not tow a heavy trailer when the car is
brand new. Wait until it has been driven
at least 1000 km.
The brakes are loaded much more than
usual on long and steep downhill slopes.
Downshift to a lower gear and adjust your
speed.
For safety reasons, the maximum permitted speed for the car when coupled with
a trailer should not be exceeded. Follow
the regulations in force for the permitted
speeds and weights.
•
Maintain a low speed when driving with a
trailer up long, steep ascents.
•
Avoid driving with a trailer on inclines of
more than 12%.
Trailer cable
An adapter is required if the car's towing
bracket has a 13 pin connector and the trailer
has a 7 pin connector. Use an adapter cable
approved by Volvo. Make sure the cable does
not drag on the ground.
Direction indicators and brake lights on
the trailer
If any of the trailer's lamps for direction indicators are broken, the symbol for direction
indicators in the combined instrument panel
flashes faster than normal and the information
display shows the text Trailer indicator
malfunction.
If any of the trailer's lamps for the brake light
are broken then the Trailer brake light
malfunction text is shown.
Related information
•
•
Towing bracket (p. 303)
Lamp replacement - general (p. 359)
Level control*
The rear shock absorbers maintain a constant
height irrespective of the car's load (up to the
maximum permissible weight). When the car
is stationary the rear of the car lowers slightly,
which is normal.
Trailer weights
For information on Volvo's permitted trailer
weights, see Towing capacity and towball
load (p. 396).
NOTE
The stated maximum permitted trailer
weights are those permitted by Volvo. The
maximum permitted speed for a car with a
trailer attached is 100 km/h. National vehicle regulations may further restrict the
trailer weight and speed. Towbars can be
certified for higher towing weights than the
car can actually tow.
WARNING
Follow the stated recommendations for
trailer weights. Otherwise, the car and
trailer may be difficult to control in the
event of sudden movement and braking.
08
* Option/accessory, for more information, see Introduction.
301
08 Starting and driving
Driving with a trailer - manual gearbox
When driving with a trailer (p. 300) in hilly terrain in a hot climate there may be a risk of
overheating.
•
Do not run the engine at higher revolutions than 4500 rpm (diesel engines:
3500 rpm) - otherwise the oil temperature
may become too high.
Driving with a trailer - automatic
gearbox
When driving with a trailer in hilly terrain in a
hot climate there may be a risk of overheating.
•
An automatic gearbox selects the optimum gear related to load and engine
speed.
•
In the event of overheating, a warning
symbol is illuminated in the combined
instrument panel and a text message is
shown in the information display - follow
the recommendation given.
Diesel engine 5-cyl
•
In the event of a risk of overheating the
optimal speed for the engine is
2300-3000 rpm for optimal circulation of
the coolant.
Related information
•
Steep inclines
•
Do not lock the automatic transmission in
a higher gear than the engine "can cope
with" - it is not always a good idea to
drive at a high gear with low engine revolutions.
Manual gearbox (p. 269)
IMPORTANT
See also the specific information on slow
driving with a trailer for cars with automatic
gearbox - Powershift (p. 274).
Parking on a hill
1. Depress the foot brake.
2. Activate the parking brake.
08
3. Move the gear selector to position P.
4. Release the foot brake.
302
* Option/accessory, for more information, see Introduction.
•
Move the gear selector to park position P
when parking an automatic car with a
hitched trailer. Always use the parking
brake.
•
Block the wheels with chocks when parking a car with hitched trailer on a hill.
Starting on a hill
1. Depress the foot brake.
2. Move the gear selector to driving position D.
3. Release the parking brake.
4. Release the foot brake and start driving
off.
Related information
•
•
Automatic gearbox - Geartronic* (p. 270)
Automatic gearbox - Powershift* (p. 274)
08 Starting and driving
Towing bracket
NOTE
A towing bracket means that it is possible to
e.g. tow a trailer behind the car.
If the car is equipped with a detachable towbar, the installation instructions for the loose
section must be followed carefully, see
Detachable towbar - attachment/removal
(p. 304).
WARNING
When a hitch with a vibration damper is
used, the towball must not be lubricated.
Detachable towbar - storage
Store the detachable towbar in the cargo
area.
Related information
•
•
•
Driving with a trailer (p. 300)
Detachable towbar - specifications
(p. 304)
Detachable towbar - storage (p. 303)
If the car is fitted with a Volvo detachable
towbar:
•
Follow the installation instructions
carefully.
•
The detachable section must be
locked with the key before setting off.
•
Check that the indicator window
shows green.
The storage location for the removable towbar.
IMPORTANT
Always remove the detachable towbar
after use and store it in the designated
location in the car.
Important checks
•
The towbar's towball must be cleaned
and greased regularly.
WARNING
The moving parts of the detachable towbar
must not be lubricated/oiled. This may
reduce safety.
Related information
•
Detachable towbar - specifications
(p. 304)
•
Detachable towbar - attachment/removal
(p. 304)
•
Driving with a trailer (p. 300)
08
303
08 Starting and driving
Detachable towbar - specifications
Detachable towbar - attachment/
removal
Specifications for detachable towbar.
The attachment/removal of the detachable
towbar is performed in the following way:
Dimensions, mounting points (mm)
A
887
B
79
C
881
D
441
E
109
F
306
G
Side member
H
Ball centre
Related information
08
304
•
Detachable towbar - attachment/removal
(p. 304)
•
•
Detachable towbar - storage (p. 303)
Driving with a trailer (p. 300)
Remove the protective cover by first
pressing in the catch
and then pulling
the cover straight back
.
G021487
G021485
Attaching
Ensure that the mechanism is in the
unlocked position by turning the key
clockwise.
The indicator window must show red.
The indicator window must show green.
G021494
G021490
G021488
08 Starting and driving
Check that the towball section is secure
by pulling it up, down and back.
WARNING
Insert the towball section until you hear a
click.
G000000
G021489
If the towball is not fitted correctly then it
must be detached and reattached in
accordance with the previous instructions.
Turn the key anticlockwise to locked
position. Remove the key from the lock.
IMPORTANT
Only grease in the ball for the towball
hitch, the remainder of the towbar must be
clean and dry.
08
}}
305
08 Starting and driving
G021495
||
Safety cable.
WARNING
Related information
•
•
Take care to secure the trailer's safety
cable in the intended bracket.
•
Removal of detachable towbar
Turn the locking wheel down fully, until it
comes to a stop. Hold it in this position
while pulling the towball rearward and
upward.
WARNING
Insert the key and turn it clockwise to the
unlocked position.
08
306
Push the protective cover until it snaps
tight.
Push in the locking wheel
and turn it
until you hear a click.
anticlockwise
Secure the detachable towbar safely if it is
stored in the car, see Detachable towbar storage (p. 303).
Detachable towbar - storage (p. 303)
Detachable towbar - specifications
(p. 304)
Driving with a trailer (p. 300)
08 Starting and driving
Trailer Stability Assist - TSA12
The trailer stability assist TSA (Trailer Stability
Assist) function is designed to stabilise the car
and trailer combination if it begins to snake.
TSA- the function is included in the stability
system (p. 183) ESC13.
Function
The snaking phenomenon can occur with any
car/trailer combination. Snaking normally
occurs at high speeds. But, there is a risk of it
occurring at lower speeds (70-90 km/h) if the
trailer is overloaded or the load is improperly
distributed, e.g. too far back.
In order for snaking to occur, there must be a
triggering factor, e.g.:
•
Car with trailer subjected to a sudden and
powerful side wind.
•
Car with trailer drives on an uneven road
surface or in a pothole.
•
Sweeping steering wheel movements.
Operation
If snaking has started, it could be difficult or
even impossible to suppress. This makes the
car/trailer combination difficult to control and
there is a risk that you could, for example,
end up in the wrong lane or leave the carriageway.
12
13
The trailer stability assist function continually
monitors car movements, particularly lateral
movements. If snaking is detected, the front
wheels are individually braked. This serves to
stabilise the car/trailer combination. This is
often enough to help the driver regain control
of the car.
whether it is the trailer or the driver that is
causing the snaking.
If snaking is not eliminated the first time the
TSA system comes into action, the car/trailer
combination is braked with all wheels and
engine power is reduced. Once snaking has
been gradually suppressed and the car/trailer
combination is once again stable, the TSA
system stops regulating and the driver once
again has full control of the car. For more
information, see Electronic stability control
(ESC) - general (p. 183).
•
The ESC13 symbol in the combined
instrument panel flashes when the
TSA system is working.
Related information
Electronic stability control (ESC) - general
(p. 183)
Miscellaneous
The TSA system can engage within the speed
interval 65-160 km/h.
NOTE
TSA function is switched off if the driver
selects Sport mode, see Electronic stability control (ESC) - general (p. 183).
TSA may fail to engage if the driver uses
severe steering wheel movements to try to
rectify the snaking because in such a situation the TSA system cannot determine
08
Included in the installation of Volvo genuine towbar.
(Electronic Stability Control) - Electronic stability control.
307
08 Starting and driving
Towing
WARNING
During towing, one vehicle is towed by
another vehicle using a tow rope.
The brake servo and power steering do not
work when the engine is switched off - the
brake pedal needs to be depressed
about 5 times more heavily and the steering is considerably heavier than normal.
Find out the statutory maximum speed limit
for towing before towing begins.
1. Unlock the steering lock (p. 267) by
inserting the remote control key in the
ignition switch and giving a long press on
the START/STOP ENGINE button - key
position II (p. 76) is activated.
2. The remote control key must remain in
the ignition switch while the car is being
towed.
Manual gearbox
Prior to towing:
–
Note that the car must always be towed
with the wheels rolling forward.
•
WARNING
08
308
•
The remote control key must be in key
position II - in position I all airbags are
deactivated.
•
Never remove the remote control key
from the ignition switch when the car
is being towed.
IMPORTANT
Avoid towing.
IMPORTANT
4. Be prepared to brake to stop.
Check that the steering lock is
unlocked before towing.
In the event of uncertainty as to whether or
not the car is equipped with Powershift transmission, this can be verified by checking the
type designation (p. 392) on the gearbox
label under the bonnet. The designation ”MPS6” means that it is Powershift transmission - otherwise it is Geartronic automatic
transmission.
Automatic gearbox Geartronic
3. Keep the towline taut when the towing
vehicle reduces speed by holding your
foot gently pressed on the brake pedal thereby avoiding unnecessary jerking.
•
Move gear lever into neutral and release
the parking brake.
lubrication. If towing still has to take place,
the route must be as short as possible and
then with very low speed.
Do not tow cars with automatic transmission at speeds higher than 80 km/h
or for distances in excess of 80 km.
Follow the speeds that are permitted
in accordance with local traffic regulations.
Prior to towing:
–
Move the gear selector to position N and
release the parking brake.
Automatic gearbox Powershift
The model with Powershift transmission
should not be towed as it is dependent on the
engine running in order to receive sufficient
•
However, the car can be towed for a
short distance at low speed to move it
from a dangerous position - not further
than 10 km and not faster than
10 km/h. Note that the car must
always be towed with the wheels rolling forward.
•
In the event of moving a longer distance than 10 km, the car must be
transported with the drive wheels
raised from the road - professional
recovery is recommended.
Prior to towing:
–
Move the gear selector to position N and
release the parking brake.
08 Starting and driving
Jump starting
Towing eye
Do not tow the car to bump start the engine.
Use a donor battery if the starter battery is
discharged and the engine does not start, see
Jump starting (p. 268).
The towing eye is screwed into a threaded
socket behind a cover on the right-hand side
of the bumper, front or rear.
IMPORTANT
The catalytic converter may be damaged
during attempts to tow-start the engine.
Related information
•
Towing eye (p. 309)
Attaching the towing eye
Take out the towing eye that is located
under the floor hatch in the cargo area.
NOTE
To access the towing eye/wheel wrench in
the foam block:
•
Version 1: Lift the emergency puncture
repair kit compressor unit (point 5) to
access the wheel wrench. Lift out the
bottle of sealant (point 6) to access the
towing eye.
•
Version 2: Lift the emergency puncture
repair kit compressor unit (point 5) to
access the towing eye. The wheel
wrench is located underneath the jack.
The cover for the towing eye's attachment point is opened as follows:
•
The cover has a marking along one
side or in a corner: Press the marking
with a finger and fold out the opposite
side/corner at the same time - the
cover turns around its axis and can
then be removed.
Screw the towing eye right in up to its
flange. Turn in the towing eye firmly e.g.
using the wheel wrench.
The towing eye is unscrewed after use.
Place the towing eye back in its position.
Finish by refitting the cover onto the
bumper.
08
}}
309
08 Starting and driving
||
IMPORTANT
The towing eye is only designed for towing
on roads - not for pulling the car unstuck
or out of a ditch. Call a recovery service for
recovery assistance.
Recovery
Recovery means that the vehicle is transported away by means of another vehicle.
Call a recovery service for recovery assistance.
Related information
•
•
IMPORTANT
Towing (p. 308)
Note that the car must always be transported with the wheels rolling forward.
Recovery (p. 310)
Related information
•
08
310
Towing (p. 308)
WHEELS AND TYRES
09 Wheels and tyres
09
Tyres - direction of rotation
NOTE
Tyres with a tread pattern which are designed
to only turn in one direction have the direction
of rotation marked with an arrow.
Make sure that both pairs of wheels have
the same type and dimension, and also the
same make.
Follow the recommended tyre pressure
(p. 322) specified in the tyre pressure table.
Related information
G021778
•
•
•
•
The arrow shows the tyre's direction of rotation.
The tyre must always rotate in the same
direction throughout its lifespan. Tyres should
only be switched between front and rear
positions, never between left and right-hand
sides, or vice versa. If the tyres are fitted
incorrectly, the car's braking characteristics
and capacity to force rain and slush out of the
way are adversely affected. Tyres with the
greatest tread depth should always be fitted
to the rear of the car (to decrease the risk of
skidding).
312
Tyres - dimensions (p. 316)
Tyres - speed ratings (p. 317)
Tyres - maintenance (p. 312)
Tyres - tread wear indicators (p. 314)
Tyres - maintenance
Amongst other things, the function of the
tyres is to provide grip on the road surface,
dampen vibration and protect the wheel from
wear.
Driving characteristics
Tyres greatly affect the car's driving characteristics. The type of tyre, dimensions, tyre
pressure and speed rating are important for
how the car performs.
Tyre age
All tyres older than 6 years old should be
checked by an expert even if they seem
undamaged. Tyres age and decompose, even
if they are hardly ever or never used. The
function can therefore be affected. This
applies to all tyres that are stored for future
use. Examples of external signs which indicate that the tyre is unsuitable for use are
cracks or discoloration.
09 Wheels and tyres
New tyres
Tyres are perishable. After a few years they
begin to harden at the same time as the friction capacity/characteristics gradually deteriorate. For this reason, aim to get as fresh
tyres as possible when you replace them.
This is especially important with regard to
winter tyres. The last four digits in the
sequence mean the week and year of manufacture. This is the tyre's DOT marking
(Department of Transportation), and this is
stated with four digits, for example 1510. The
tyre in the figure was manufactured in week
15 of 2010.
Summer and winter tyres
When summer and winter wheels are
changed the wheels should be marked with
which side of the car they were mounted on,
for example L for left and R for right.
Wear and maintenance
Correct tyre pressure (p. 322) results in more
even wear. Driving style, tyre pressure, climate and road condition affect how quickly
your tyres age and wear. To avoid differences
in tread depth and to prevent wear patterns
(p. 314) arising, the front and rear wheels can
be switched with each other. A suitable distance for the first change is approx. 5000 km
and then at 10000 km intervals. Volvo recommends that you contact an authorised Volvo
workshop for checking if you are uncertain
about tread depth. If significant differences in
wear (>1 mm difference in tread depth)
between tyres have already occurred, the
least worn tyres must always be placed on
the rear. Understeer is normally easier to correct than oversteer, and leads to the car continuing forwards in a straight line rather than
having the rear end skidding to one side,
resulting in possible complete loss of control
over the car. This is why it is important for the
rear wheels never to lose grip before the front
wheels.
Related information
•
•
•
09
Tyres - dimensions (p. 316)
Tyres - speed ratings (p. 317)
Tyres - direction of rotation (p. 312)
Wheels must be stored lying down or hanging
up - never standing up.
WARNING
A damaged tyre may lead to loss of control
over the car.
313
09 Wheels and tyres
09
Tyres - tread wear indicators
Wheel nuts
Locking wheel nuts*
A tread wear indicator shows the status of the
tyre's tread.
Wheel nuts are used to fasten the wheels at
the hubs and are available in different versions.
Locking wheel nuts can be used on both aluminium and steel rims. Under the cargo area
floor there is space for the sleeve for the lockable wheel nuts.
Related information
G021829
•
Tread wear indicators.
Tread wear indicators are narrow treadless
bands across the width of the tread. On the
side of the tyre are the letters TWI (Tread
Wear Indicator). When the tyre's tread depth
is down to 1.6 mm, the tread depth will be
level in height with the tread wear indicators.
Change to new tyres as soon as possible.
Remember that tyres with little tread depth
provide very poor grip in rain and snow.
Related information
•
•
•
314
Tyres - speed ratings (p. 317)
Tyres - air pressure (p. 322)
Tyres - direction of rotation (p. 312)
Standard wheel nuts
Bulge acorn wheel nuts
Locking wheel nuts
Tightening torque
•
Type 1 wheel nut (steel wheel rim): 110
Nm
•
Type 2 wheel nut (aluminium wheel
rim): 130 Nm
•
Type 3 Lockable wheel nut (steel/
aluminium wheel rim): 110 Nm
Only use rims that are tested and approved
by Volvo and which are Volvo genuine accessories. Check the torque with a torque
wrench.
* Option/accessory, for more information, see Introduction.
Wheel and wheel rim dimensions (p. 316)
09 Wheels and tyres
Jack
Winter tyres
Using snow chains
A jack is used to raise the car, e.g. when
changing the tyres.
Winter tyres are tyres that are adapted for
winter road conditions.
The original jack should only be used for
changing to the spare wheel. The jack's
thread must always be well greased.
Winter tyres
Snow chains may only be used on the front
wheels (also applies to all-wheel drive cars).
Never drive faster than 50 km/h with snow
chains. Avoid driving on bare ground as this
wears out both the snow chains and tyres.
Related information
•
•
Warning triangle (p. 323)
Emergency puncture repair* (p. 331)
Volvo recommends winter tyres with particular dimensions. Tyre dimensions are dependent on engine variant. When driving on winter
tyres, the correct type of tyres must be fitted
to all four wheels.
WARNING
Use Volvo genuine snow chains or equivalent chains designed for the car model,
and tyre and rim dimensions. In the event
of uncertainty Volvo recommends that you
consult an authorised Volvo workshop.
The wrong snow chains may cause serious
damage to your car and lead to an accident.
NOTE
Volvo recommends that you consult a
Volvo dealer about which wheel rim and
tyre types are most suitable.
Studded tyres
Studded winter tyres should be run in gently
for 500-1000 km so the studs settle properly
into the tyres. This gives the tyre, and especially the studs, a longer service life.
09
Related information
•
Changing wheels - removing wheels
(p. 319)
NOTE
The legal provisions for the use of studded
tyres vary from country to country.
Tread depth
Road conditions with ice, slush and low temperatures place considerably higher demands
on tyres than summer conditions. Volvo
therefore recommends not to drive on winter
tyres that have a tread depth of less
than4 mm.
* Option/accessory, for more information, see Introduction.
315
09 Wheels and tyres
09
Wheel and wheel rim dimensions
Tyres - dimensions
Tyres - load index
Wheel and rim dimensions are designated in
accordance with the examples in the table
below.
The car's wheels, tyres and rims have a certain dimension, see the examples in the table
below.
Load index indicates a tyre's ability to carry a
certain load.
Wheels (rims) have a designation of dimensions, for example: 7Jx16x50.
The dimensions are stated on all car tyres.
Example of designation:215/55R16 97W.
7
Rim width in inches
205
Tyre width (mm)
J
Rim flange profile
50
16
Rim diameter in inches
Ratio between tyre wall height and
tyre width (%)
50
Off-set in mm (distance from wheel
centre to wheel contact surface
against the hub)
R
Radial ply
17
Rim diameter in inches (")
93
Codes for the maximum permitted
tyre load, load index (p. 316) (LI)
W
Speed rating for maximum permitted
speed, speed rating (p. 317) (SS). (In
this case 270 km/h).
Related information
•
Wheel nuts (p. 314)
Related information
•
•
•
316
Tyres - air pressure (p. 322)
Tyres - direction of rotation (p. 312)
Tyres - tread wear indicators (p. 314)
Each tyre has a certain capacity to carry a
load, a load index (LI). The car's weight determines the load capacity required of the tyres.
Related information
•
•
•
•
Tyres - dimensions (p. 316)
Tyres - speed ratings (p. 317)
Tyres - air pressure (p. 322)
Tyres - tread wear indicators (p. 314)
09 Wheels and tyres
Tyres - speed ratings
Tyre speed class must at least correspond
with the car's top speed. Minimum speed rating is indicated in the speed rating table
below. The only exception to these conditions
is winter tyres (p. 315) (both those with metal
studs and those without), where a lower
speed rating may be used. If such a tyre is
chosen, the car must not be driven faster
than the speed rating of the tyre (for example,
class Q can be driven at a maximum of
160 km/h). Traffic regulations determine how
fast a car can be driven, not the speed rating
of the tyres.
NOTE
Spare wheel*
WARNING
Each tyre can withstand a certain maximum
speed and therefore belongs to a particular
speed rating (SS - Speed Symbol).
The car must be fitted with tyres which
have the same or a higher load index
(p. 316) (LI) and speed rating (SS) than
specified. If a tyre with too low a load
index or speed rating is used, it may overheat.
Related information
•
•
•
Tyres - dimensions (p. 316)
Tyres - air pressure (p. 322)
Tyres - direction of rotation (p. 312)
A spare wheel is only intended for use temporarily and must be replaced by an normal
wheel as soon as possible. The car's handling
may be altered by the use of a spare wheel.
The spare wheel is smaller than the normal
wheel. The car's ground clearance is affected
accordingly. Pay attention to high kerbs and
do not machine wash the car. If the spare
wheel is fitted on the front axle, you cannot
use snow chains at the same time. On allwheel drive cars the drive on the rear axle can
be disconnected. The spare wheel must not
be repaired. The correct tyre pressure for the
spare wheel is stated in the tyre pressure
table, Tyres - air pressure (p. 322).
The maximum permitted speed is specified in the table.
Q
160 km/h (used only on winter tyres)
T
190 km/h
H
210 km/h
V
240 km/h
W
270 km/h
Y
300 km/h
09
A spare wheel (Temporary spare) is used to
temporarily replace a punctured normal
wheel.
IMPORTANT
•
Never drive faster than 80 km/h with a
spare wheel on the car.
•
The car must never be driven fitted
with more than one "Temporary
Spare" wheel.
Related information
•
Changing wheels - removing wheels
(p. 319)
•
Changing wheels - fitting the spare
wheel* (p. 320)
* Option/accessory, for more information, see Introduction.
}}
317
09 Wheels and tyres
09
•
•
•
•
Changing wheels - taking out the spare
wheel* (p. 318)
Changing wheels - taking out the
spare wheel*
Jack (p. 315)
The spare wheel* plus jack* and wheel
wrench* are stored under the floor in the
cargo area.
Warning triangle (p. 323)
Wheel nuts (p. 314)
5. Take hold of the far end of the spare
wheel, then lift. Push the spare wheel forwards slightly and lift it out of the storage
compartment.
6. Remove the wheel wrench, the jack and
the towing eye from the foam block.
NOTE
The jack must be lifted out in order to
access the towing eye.
Related information
1. Lift the rear edge of the luggage compartment floor (or on models with a jointed
luggage compartment floor, take hold of
the luggage compartment floor handle, lift
and move the rear part of the floor forwards).
2. Lift out the storage compartment* (only
models with a jointed cargo area floor).
3. Lift out the lower floor (models with a jointed luggage compartment floor only).
4. Undo the attaching screw and lift out the
foam block containing the jack and tools.
318
* Option/accessory, for more information, see Introduction.
•
Changing wheels - removing wheels
(p. 319)
•
Changing wheels - fitting the spare
wheel* (p. 320)
•
•
•
•
Jack (p. 315)
Spare wheel* (p. 317)
Warning triangle (p. 323)
Wheel nuts (p. 314)
09 Wheels and tyres
Changing wheels - removing wheels
The car's wheels can be changed for e.g. winter wheels/winter tyres.
Set up the warning triangle if a wheel must be
changed in a trafficked location. The car and
jack* must be on a firm horizontal surface.
1. Apply the parking brake and engage
reverse gear, or position P if the car has
an automatic gearbox.
3. Place chocks in front of and behind the
wheels which will remain on the ground to
prevent them from rolling. Use heavy
wooden blocks or large stones for example.
5. Screw together the towing eye with the
wheel wrench* until the stop position as
shown in the following illustration.
09
4. Cars with steel rims have removable
wheel covers. Use the removal tool to
hook in and pull off any full-wheel wheel
covers. Alternatively, the wheel covers
can be pulled away by hand.
WARNING
Check that the jack is not damaged, that
the threads are thoroughly lubricated and
that it is free from dirt.
NOTE
Volvo recommends only using the jack*
that belongs to the car model in question,
which is indicated on the jack's label.
The decal also indicates the jack's maximum lift capacity at a specified lifting
height.
The wheel wrench and towing eye.
IMPORTANT
The towing eye must be screwed into all
threads in the wheel bolt wrench.
6. Loosen the wheel nuts ½-1 turn anticlockwise with the wheel wrench.
2. Take out the wheel to be fitted (summer
tyre, winter tyre or spare wheel) as well as
the tools. If it is a spare wheel being fitted
then there is a package in its location
containing gloves and a plastic bag for
the punctured wheel.
}}
* Option/accessory, for more information, see Introduction.
319
09 Wheels and tyres
09
||
WARNING
WARNING
Never position anything between the
ground and the jack, nor between the jack
and the car's jacking point.
Never crawl under the car when it is raised
on the jack.
7. There are two jacking points on each side
of the car.
Park the car such that passengers have
the car, or ideally a crash barrier, between
themselves and the roadway.
Passengers must leave the car when it is
raised on the jack.
NOTE
The car's regular jack is designed only for
use occasionally and for a short time, such
as when changing a wheel with a punctured tyre, switching between summer
tyres and winter tyres, etc. Only the jack
belonging to the specific model is to be
used to jack up the car. If the car is to be
jacked up more often, or for a longer time
than is required just to change a wheel,
use of a garage jack is recommended. In
this instance, follow the instructions for
use that come with the equipment.
IMPORTANT
The ground under the jack must be firm,
smooth and level.
320
Changing wheels - fitting the spare
wheel*
It is important that the procedure for fitting
the spare wheel is carried out correctly.
Fitting
1. Clean the contact surfaces between
wheel and hub.
2. Put on the wheel. Tighten the wheel nuts
thoroughly.
3. Lower the car so that the wheels cannot
rotate.
Related information
•
8. Wind up the jack so that the flange in the
bodywork ends up in the notch in the
head of the jack.
Changing wheels - fitting the spare
wheel* (p. 320)
•
Changing wheels - taking out the spare
wheel* (p. 318)
9. Lift the car so that the wheel is free.
Remove the wheel nuts and lift off the
wheel.
•
•
•
Spare wheel* (p. 317)
* Option/accessory, for more information, see Introduction.
Warning triangle (p. 323)
Wheel nuts (p. 314)
4. Tighten the wheel nuts crosswise. It is
important that the wheel nuts are tightened with the correct tightening torque.
Check the torque with a torque wrench.
09 Wheels and tyres
Putting back the jack* and tools
5.
3. If the spare wheel has been used, then
the punctured wheel can be placed in the
plastic bag contained in the package with
the gloves. Place the foam block back in
the storage compartment and tighten the
mounting screw to the floor of the storage
compartment.
09
If the spare wheel has not been used,
place the foam block in the spare wheel
and place the spare wheel back in the
storage compartment. Tighten the attaching screw to the floor of the storage compartment.
Refit any full wheel covers.
NOTE
The wheel cover outlet for the valve must
be positioned over the valve on the wheel
rim during fitting.
The tools and jack must be returned to their
correct places in the foam block after use.
1. Unscrew the towing eye from the wheel
bolt wrench.
2. Put back any tools that have been used in
the relevant compartments in the foam
block in the following order:
•
towing eye/funnel/torx wrench/socket
for locking wheel nuts/tool for wheel
covers
•
jack (must be cranked to the correct
height so that it fits into the foam
block's compartment, the handle
above the foot and down in the groove
in the foam block)
•
socket wrench (above the jack).
4. Return the detachable towbar.
NOTE
•
After a tyre has been inflated, always
refit the dust cap in order to avoid
damage to the valve from gravel, dirt,
etc.
•
Only use plastic dust caps. Metal dust
caps can rust and become difficult to
unscrew.
IMPORTANT
The tools and jack* must be stored in the
intended location in the car's cargo area
when not in use.
}}
* Option/accessory, for more information, see Introduction.
321
09 Wheels and tyres
||
Related information
Tyres - air pressure
•
Changing wheels - taking out the spare
wheel* (p. 318)
•
Tyres can have different air pressures which
are measured in bar.
Changing wheels - removing wheels
(p. 319)
Check the air pressure in the tyres
•
•
•
Spare wheel* (p. 317)
Warning triangle (p. 323)
Wheel nuts (p. 314)
The air pressure for the tyres should be
checked every month and should be checked
on cold tyres. "Cold tyres" means the tyres
are the same temperature as the ambient
temperature. After several few kilometres of
driving, the tyres warm up and the pressure
increases. Inadequate tyre pressure increases
fuel consumption, shortens tyre lifespan and
impairs the car's roadholding. Driving on
tyres with tyre pressure that is too low could
result in the tyres overheating and being
damaged. Tyre pressure affects travelling
comfort, road noise and steering characteristics.
NOTE
Tyre pressure decreases over time, this is
a natural phenomenon. Tyre pressure also
varies depending on ambient temperature.
Tyre pressure label
G021830
09
The tyre pressure label on the driver's side
door pillar (between frame and rear door)
shows which pressure the tyres should have
at different loads and speed conditions. This
is also specified in the tyre pressure table.
Tyre pressure for the car's recommended tyre
dimension and information about ECO pressure that results in improved fuel economy
can be found in the printed owner's manual.
NOTE
Temperature differences change the
tyre pressure.
Fuel economy, ECO pressure
In order to obtain optimum fuel economy at
speeds below 160 km/h an ECO pressure is
recommended (applies to both full and light
322
* Option/accessory, for more information, see Introduction.
09 Wheels and tyres
load - see the tyre pressure in the printed
owner's manual).
Related information
•
•
•
•
Tyres - speed ratings (p. 317)
Warning triangle
Lift the floor hatch (or push the rear part
of the luggage compartment floor forwards in models with a jointed floor and
then lift the lower floor) and remove the
warning triangle.
The warning triangle is used to warn other
road users of a stationary vehicle.
Storage and folding up
Tyres - direction of rotation (p. 312)
09
Take the warning triangle from the case,
fold out and assemble the two loose
sides.
Tyres - maintenance (p. 312)
Tyres - tread wear indicators (p. 314)
Fold out the warning triangle's support
legs.
Follow the regulations for the use of a warning triangle. Position the warning triangle in a
suitable place with regard to traffic.
Ensure the warning triangle and its case are
properly secured in the cargo area after use.
Related information
•
Spare wheel* (p. 317)
* Option/accessory, for more information, see Introduction.
323
09 Wheels and tyres
09
First aid kit*
Tyre pressure monitoring*1
Related information
The first aid box contains first aid equipment.
Tyre pressure monitoring warns the driver
when the pressure is too low in one or more
of the car's tyres. For certain markets the tyre
pressure monitoring is standard in accordance with legal requirements.
•
TPMS (Tyre Pressure Monitoring System)*
- general (p. 325)
•
TPMS (Tyre Pressure Monitoring System)*
- adjusting (recalibration) (p. 326)
•
TPMS (Tyre Pressure Monitoring System)*
- rectifying low tyre pressure (p. 329)
•
TPMS (Tyre Pressure Monitoring System)*
- activate/deactivate (p. 327)
•
TPMS (Tyre Pressure Monitoring System)*
- recommendations (p. 328)
•
TPMS (Tyre Pressure Monitoring System)*
- driveable punctured tyres* (p. 328)
•
TPMS (Tyre Pressure Monitoring System)*
status (p. 326)
There are two systems for tyre pressure
monitoring, TPMS (Tyre Pressure Monitoring
System) and TM (Tyre Monitor). In the event
of uncertainty about which system the car
has, open the menu system MY CAR and
search for the car's settings:
A case containing first aid equipment is
located on the left-hand side of the cargo
area.
•
The Tyre pressure menu is used if it is
TPMS, see TPMS (Tyre Pressure
Monitoring System)* - general (p. 325).
•
The Tyre monitoring menu is used if it is
TM, see TM (Tyre Monitor)* (p. 329).
The system does not replace normal tyre
maintenance.
IMPORTANT
If a fault occurs in the TPMS system the
warning lamp
in the combined instrument panel will flash for approx. 1 minute
and then illuminate with a constant glow. A
message is also shown in the combined
instrument panel.
1
324
Standard in certain markets.
* Option/accessory, for more information, see Introduction.
09 Wheels and tyres
TPMS (Tyre Pressure Monitoring
System)*9 - general
• Tyre pressure system Service
•
TPMS (Tyre Pressure Monitoring System)*
- recommendations (p. 328)
Tyre pressure monitoring (TPMS) (Tyre
Pressure Monitoring System)* warns the
driver when the pressure is too low in one or
more of the car's tyres.
If wheels without TPMS sensors are used or if
a sensor has failed then Tyre pressure
system Service required will be shown.
•
TPMS (Tyre Pressure Monitoring System)*
- driveable punctured tyres* (p. 328)
•
TPMS (Tyre Pressure Monitoring System)*
status (p. 326)
Tyre pressure monitoring uses sensors
located inside the air valve in each wheel.
When the car is driven at about 30 km/h the
system detects the tyre pressure. If the pressure is too low then a warning lamp
illuminates in the combined instrument panel
and one of the following messages is shown:
required
Always check the system after changing a
wheel in order to ensure that replacement
wheels work with the system.
For information on the correct tyre pressure,
see Tyres - air pressure (p. 322).
The system does not replace normal tyre
maintenance.
• Tyre pressure low Check front right
IMPORTANT
tyre
If a fault occurs in the TPMS system the
in the combined instruwarning lamp
ment panel will flash for approx. 1 minute
and then illuminate with a constant glow. A
message is also shown in the combined
instrument panel.
• Tyre pressure low Check front left
tyre
•
Tyre pressure low Check rear right
tyre
• Tyre pressure low Check rear left tyre
• Tyre needs air now Check front right
tyre
• Tyre needs air now Check front left
tyre
• Tyre needs air now Check rear right
tyre
• Tyre needs air now Check rear left
tyre
9
09
Related information
•
TPMS (Tyre Pressure Monitoring System)*
- adjusting (recalibration) (p. 326)
•
TPMS (Tyre Pressure Monitoring System)*
- rectifying low tyre pressure (p. 329)
•
TPMS (Tyre Pressure Monitoring System)*
- activate/deactivate (p. 327)
Standard in certain markets.
* Option/accessory, for more information, see Introduction.
325
09 Wheels and tyres
09
TPMS (Tyre Pressure Monitoring
System)*16 - adjusting (recalibration)
Tyre pressure monitoring (TPMS) (Tyre
Pressure Monitoring System)* warns the
driver when the pressure is too low in one or
more of the car's tyres.
TPMS can be adjusted in order to follow Volvo's tyre pressure recommendations (p. 322),
when driving with a heavy load for example.
5. Drive for at least 10 minutes at a speed of
at least 30 km/h.
> Calibration is performed automatically
following initialisation by the driver.
The system provides no confirmation
when the calibration is complete.
Related information
•
•
NOTE
The car must be stationary when calibration is started.
The settings are made with the control in the
centre console, see MY CAR (p. 108).
Tyre pressure monitoring* (p. 324)
Tyres - air pressure (p. 322)
TPMS (Tyre Pressure Monitoring
System)*18 status
Tyre pressure monitoring (TPMS) (Tyre
Pressure Monitoring System)* warns the
driver when the pressure is too low in one or
more of the car's tyres.
System and tyre status
The current status of the system and the tyres
can be checked, see MY CAR (p. 108).
1. Select the menu system MY CAR to open
the menus for tyre monitoring.
2. Select Tyre pressure.
The status is colour-coded for each tyre in
accordance with the following:
•
All-green: the system is operating normally and the tyre pressure in all tyres is
slightly above the recommended level.
•
Yellow wheel: corresponding tyre's pressure is too low.
2. Start the engine.
•
3. Select the menu system MY CAR to open
the menus for tyre pressure.
Red wheel: corresponding tyre's pressure
is very low.
•
All wheels grey: the system is temporarily
unavailable. It may be necessary to drive
the car for a few minutes at a speed
above 30 km/h before the system
becomes active again.
•
All wheels grey and the message Tyre
pressure system Service required: an
1. Inflate the tyres to the desired pressure in
accordance with the tyre pressure label
on the driver's side door pillar (between
front and rear doors).
4. Select Calibrate tyre pressure and
press OK.
16
18
326
Standard in certain markets.
Standard in certain markets.
* Option/accessory, for more information, see Introduction.
09 Wheels and tyres
error has occurred in the system. Contact
a Volvo dealer or workshop.
NOTE
•
Clearing warning messages
If a tyre pressure message has been shown
and the TPMS warning lamp has been illuminated:
1. Check the tyre pressure on the indicated
tyre/tyres with a tyre pressure gauge.
2. Inflate the tyre/tyres to the correct pressure in accordance with the tyre pressure
label on the driver's side door pillar
(between front and rear doors).
•
3. In some cases it may be necessary to
drive the car for a few minutes at a speed
above 30 km/h in order to clear the warning text. At which point, the TPMS warning lamp is extinguished as well.
The TPMS system uses a so-called
compensated pressure value, based
on both tyre temperature and ambient
temperature. This means that the tyre
pressure may differ slightly from the
recommended pressures listed on the
tyre pressure label on the driver's side
door pillar (between front and rear
doors). For this reason, it may be necessary to inflate the tyres to a slightly
higher pressure in order to clear a low
tyre pressure message.
To avoid incorrect tyre pressure, the
pressure should be checked on cold
tyres. "Cold tyres" means the tyres are
the same temperature as the ambient
temperature (approx. 3 hours after the
car has been driven). After a few kilometres of driving, the tyres warm up
and the pressure increases.
WARNING
•
Incorrect tyre pressure may lead to
tyre failure, which could result in the
driver losing control of the car.
•
The system cannot indicate sudden
tyre damage in advance.
TPMS (Tyre Pressure Monitoring
System)*20 - activate/deactivate
09
Tyre pressure monitoring (TPMS) (Tyre
Pressure Monitoring System)* warns the
driver when the pressure is too low in one or
more of the car's tyres.
NOTE
The car must be stationary when the tyre
pressure monitoring is activated/deactivated.
Settings are made using the centre console's
controls, see MY CAR (p. 108).
1. Start the engine.
2. Select the system MY CAR to open the
menus for tyre pressure.
3. Select Tyre pressure and press OK.
> An X is shown in the information display if the system is activated, the
option disappears if the system is
deactivated21.
Related information
•
Tyre pressure monitoring* (p. 324)
Related information
•
20
Tyre pressure monitoring* (p. 324)
Standard in certain markets.
* Option/accessory, for more information, see Introduction.
327
09 Wheels and tyres
09
TPMS (Tyre Pressure Monitoring
System)*23 - recommendations
WARNING
When inflating a tyre equipped with TPMS,
hold the nozzle of the pump directly
against the valve to avoid damaging the
valve.
Tyre pressure monitoring (TPMS) (Tyre
Pressure Monitoring System)* warns the
driver when the pressure is too low in one or
more of the car's tyres.
•
•
Volvo recommends that sensors are not
moved between different wheels.
•
The spare wheel is not equipped a with
TPMS sensor.
•
If the spare wheel or a wheel without a
TPMS sensor is used, the error message
Tyre pressure system Service
required will be shown in the combined
instrument panel.
•
If a wheel has been changed, or if the
TPMS sensor has been moved to another
wheel then the seal, nut and valve core
must be replaced.
•
When TPMS sensors are installed, the car
should be switched off for at least 15
minutes otherwise an error message will
be shown in the combined instrument
panel.
21
23
25
328
NOTE
Volvo recommends that TPMS sensors
are fitted to all wheels on the car, including winter wheels.
•
After a tyre has been inflated, always
refit the dust cap in order to avoid
damage to the valve from gravel, dirt,
etc.
•
Only use plastic dust caps. Metal dust
caps can rust and become difficult to
unscrew.
NOTE
If you want to change the tyre dimension
then the TPMS system must be reconfigured. For further information - contact a
Volvo dealer.
Related information
•
Only in certain markets.
Standard in certain markets.
Standard in certain markets.
* Option/accessory, for more information, see Introduction.
Tyre pressure monitoring* (p. 324)
TPMS (Tyre Pressure Monitoring
System)*25 - driveable punctured
tyres*
If SST (Self Supporting run flat Tires)* is
selected, the car is also equipped with TPMS
(p. 324).
This type of tyre has a specially reinforced
side wall that makes continued driving possible to a limited extent despite the tyre losing
all or some of its pressure. These tyres are fitted on a special rim. (Normal tyres can also
be fitted to this rim.)
If an SST tyre loses tyre pressure then the
yellow TPMS lamp in the combined instrument panel illuminates and a message is
shown in the information display. If this
occurs, reduce speed to max. 80 km/h. The
tyre must be replaced as soon as possible.
Drive carefully, in some cases it can be difficult to see which tyre is faulty. In order to
establish which tyre needs attention, check
all four tyres.
09 Wheels and tyres
WARNING
Only people with knowledge of SST tyres
should fit them.
SST tyres must only be fitted together with
TPMS.
After an error message about low tyre
pressure has been shown, do not drive
faster than 80 km/h.
Maximum mileage before tyre replacement
is 80 km.
Avoid hard driving such as sudden braking
or turning.
SST tyres must be replaced if they are
damaged or punctured.
Related information
•
Tyre pressure monitoring* (p. 324)
TPMS (Tyre Pressure Monitoring
System)*27 - rectifying low tyre
pressure
TM (Tyre Monitor)*30
The tyre pressure monitoring system TPMS
(Tyre Pressure Monitoring System)28 warns
the driver when the pressure is too low in one
or more of the car's tyres and indicates the
tyre to which it applies. The lamp illuminates
in yellow at the first indication, stop and
check the tyre pressure as soon as possible.
When the lamp illuminates in red you must
stop and rectify the tyre pressure immediately.
If a message for low tyre pressure is shown in
the display:
1. Check the tyre pressure on the tyre in
question.
3. Drive at least at 30 km/h for several
minutes and check that the message disappears.
•
27
28
30
Tyre pressure monitoring* (p. 324)
The TM (Tyre Monitor) system senses tyre
rotation speed in order to determine whether
the tyres have the correct tyre pressure. If the
pressure is too low, the tyre's diameter is
changed and, as a result, so is the rotation
speed. By comparing the tyres with each
other the system can determine whether one
or more tyres have pressure that is too low.
Messages
If the tyre pressure is too low then a warning
lamp ( ) illuminates in the combined instrument panel and one of the following messages is shown:
• Tyre pressure low Check front right
tyre
2. Inflate the tyre(s) to the correct pressure.
Related information
09
• Tyre pressure low Check front left
tyre
• Tyre pressure low Check rear right
tyre
• Tyre pressure low Check rear left tyre
• Tyre pressure low Check tyres
• Tyre pressure system Service
required
Standard in certain markets.
Option only in certain markets.
Standard in certain markets.
}}
* Option/accessory, for more information, see Introduction.
329
09 Wheels and tyres
09
||
IMPORTANT
If a fault occurs in the TM system the
warning lamp
in the combined instrument panel will flash for approx. 1 minute
and then illuminate with a constant glow. A
message is also shown in the combined
instrument panel.
The system does not replace normal tyre
maintenance.
5. Start and drive the car.
> Recalibration is carried out while the
car is being driven and can be interrupted at any time. If the engine is
switched off while recalibration is in
progress then it is resumed when the
car is driven again.
TM is then recalibrated and the new reference
value applies until steps 1-5 are carried out
again.
TM recalibration
In order for TM to work correctly, a reference
value for the tyre pressure must be determined. This must be performed each time the
tyres are changed or the tyre pressure is
changed.
1. Switch off the ignition.
2. Inflate the tyres to the desired pressure in
accordance with the tyre pressure label
on the driver's side door pillar (between
front and rear doors) and select key position II, see Key positions (p. 75).
3. Select the menu system MY CAR to open
the menus for tyre pressure.
4. Select Calibrate tyre pressure and
press OK.
330
The current status of the system and the tyres
can be checked, see MY CAR (p. 108).
1. Select the menu system MY CAR to open
the menus for tyre monitoring.
2. Select Tyre monitoring.
The status is colour-coded for each tyre in
accordance with the following:
•
All-green: the system is operating normally and the tyre pressure in all tyres is
slightly above the recommended level.
•
Yellow wheel: corresponding tyre's pressure is too low.
•
All wheels yellow: two or more tyres have
pressure that is too low.
•
All wheels grey: the system is temporarily
unavailable. It may be necessary to drive
the car for a few minutes at a speed
above 30 km/h before the system
becomes active again.
•
All wheels grey and the message Tyre
pressure system Service required: an
error has occurred in the system. Contact
a Volvo dealer or workshop.
NOTE
Remember that the TM system must be
recalibrated at each tyre change or if the
tyre pressure is changed. If new reference
values are not stored then the system cannot function properly.
Recalibration
Settings are made using the centre console's
controls, see MY CAR (p. 108).
System and tyre status
NOTE
•
•
After a tyre has been inflated, always
refit the dust cap in order to avoid
damage to the valve from gravel, dirt,
etc.
Only use plastic dust caps. Metal dust
caps can rust and become difficult to
unscrew.
Clearing warning messages
If a tyre pressure message has been shown
and the TPI warning lamp has been illuminated:
09 Wheels and tyres
1. Check the tyre pressure on the indicated
tyre/tyres with a tyre pressure gauge.
2. Inflate the tyre/tyres to the correct pressure in accordance with the tyre pressure
label on the driver's side door pillar
(between front and rear doors).
3. Recalibrate the TM system.
NOTE
•
•
The TM system uses a so-called compensated pressure value, based on
both tyre temperature and ambient
temperature. This means that the tyre
pressure may differ slightly from the
recommended pressures listed on the
tyre pressure label on the driver's side
door pillar (between front and rear
doors). For this reason, it may be necessary to inflate the tyres to a slightly
higher pressure in order to clear a low
tyre pressure message.
To avoid incorrect tyre pressure, the
pressure should be checked on cold
tyres. "Cold tyres" means the tyres are
the same temperature as the ambient
temperature (approx. 3 hours after the
car has been driven). After a few kilometres of driving, the tyres warm up
and the pressure increases.
WARNING
•
Incorrect tyre pressure may lead to
tyre failure, which could result in the
driver losing control of the car.
•
The system cannot indicate sudden
tyre damage in advance.
Emergency puncture repair*
09
The emergency puncture repair kit* (TMK Temporary Mobility Kit) is used to seal a
puncture and check and adjust the air pressure. Air pressure for the car's recommended
tyre dimensions can be found in the printed
owner's manual.
The emergency puncture repair kit consists of
a compressor and a bottle of sealant. The
sealing works as a temporary repair. The
sealing fluid bottle must be replaced before
its expiration date and after use. The sealing
fluid effectively seals tyres punctured in the
tread.
NOTE
The emergency puncture repair kit is only
intended for sealing tyres with a puncture
in the tread.
The emergency puncture repair kit has limited
capacity to seal tyres which have punctures
in the wall. Do not seal tyres with the emergency puncture repair kit if they have larger
slits, cracks or similar damage. Connect the
compressor to one of the car's 12 V sockets.
Choose the socket that is nearest to the
punctured tyre.
}}
* Option/accessory, for more information, see Introduction.
331
09 Wheels and tyres
09
||
NOTE
The compressor for temporary emergency
puncture repair has been tested and
approved by Volvo.
Related information
•
Emergency puncture repair* - operation
(p. 334)
•
Emergency puncture repair* - rechecking
(p. 335)
•
Emergency puncture repair kit* - overview
(p. 333)
Emergency puncture repair kit* location
Emergency puncture repair kit (TMK - Temporary Mobility Kit) is used to seal a puncture
and check and adjust the air pressure. Air
pressure for the car's recommended tyre
dimensions can be found in the printed
owner's manual.
Location of the emergency puncture
repair kit
Version 2.
Set up the warning triangle if a tyre is being
sealed in a trafficked location. The warning
triangle and emergency puncture repair kit
are located under the floor in the cargo area.
Version 1.
1. Lift the rear edge of the luggage compartment floor (or on models with a jointed
luggage compartment floor, take hold of
the luggage compartment floor handle, lift
and move the rear part of the floor forwards).
2. Lift out the storage compartment
(optional extra) - models with a jointed
luggage compartment floor only.
3. Lift out the lower floor (models with a jointed luggage compartment floor only).
4. Unhook the elastic part of the belt over
the TMK compressor unit on the left side.
332
* Option/accessory, for more information, see Introduction.
09 Wheels and tyres
5. Lift the TMK compressor unit straight up.
6. To access the bottle of sealant, it must be
pushed to the left until it can be lifted out
of the foam block.
NOTE
To access the towing eye/wheel wrench in
the foam block:
•
•
Emergency puncture repair kit* overview
Bottle holder with sealant
Emergency puncture repair kit (TMK - Temporary Mobility Kit) is used to seal a puncture
and check and adjust the air pressure. Air
pressure for the car's recommended tyre
dimensions can be found in the printed
owner's manual.
Version 1: Lift the emergency puncture repair kit compressor unit (point 5)
to access the wheel wrench. Lift out
the bottle of sealant (point 6) to access
the towing eye.
09
Pressure gauge
Related information
•
Emergency puncture repair kit* - location
(p. 332)
•
Emergency puncture repair kit* - sealant
(p. 338)
•
•
Emergency puncture repair* (p. 331)
Emergency puncture repair* - stowing
components (p. 337)
Version 2: Lift the emergency puncture repair kit compressor unit (point 5)
to access the towing eye. The wheel
wrench is located underneath the jack.
After use, hook the belt back onto the left
side.
Version 1: The belt must be pulled behind the
foam block (not above).
Version 2: The belt must be in the fork on the
rear part of the foam block.
Related information
Label, maximum permitted speed
Switch
Cable
Bottle holder (orange cap)
•
Emergency puncture repair kit* - overview
(p. 333)
Protective cap
•
Emergency puncture repair kit* - sealant
(p. 338)
Pressure reducing valve
•
Emergency puncture repair* (p. 331)
Air hose
* Option/accessory, for more information, see Introduction.
333
09 Wheels and tyres
09
Emergency puncture repair* operation
Emergency puncture repair, using the emergency puncture repair kit* (TMK - Temporary
Mobility Kit) is used to seal a puncture and
check and adjust the air pressure. Air pressure for the car's recommended tyre dimensions can be found in the printed owner's
manual.
Emergency puncture repair
1. Detach the label for maximum permitted
speed (which is fitted on one side of the
compressor) and affix it to the steering
wheel.
WARNING
You should not drive faster than 80 km/h
after the emergency tyre repair kit has
been used. Volvo recommends that you
visit an authorised Volvo workshop for
inspection of the sealed tyre (maximum
driving distance is 200 km). The staff there
can determine whether or not the tyre can
be repaired or if it needs to be replaced.
WARNING
The sealing fluid can irritate the skin. In the
case of contact with skin, wash away the
fluid with soap and water.
2. Check that the switch is in position 0 and
locate the cable and the air hose.
NOTE
Do not break the bottle's seal before use.
The seal is broken automatically when the
bottle is screwed in.
3. Unscrew the orange cap and unscrew the
bottle's stopper.
For information on the function of the parts, see
Emergency puncture repair kit.
334
* Option/accessory, for more information, see Introduction.
4. Screw the bottle into its holder.
WARNING
Do not unscrew the bottle, it is equipped
with a reverse catch to prevent leakage.
5. Unscrew the wheel's dust cap and screw
in the air hose valve connection to the
bottom of the thread on the tyre's air
valve.
6. Plug the cable into the 12 V socket and
start the car.
WARNING
Do not leave children in the car without
supervision when the engine is running.
09 Wheels and tyres
7. Flick the switch to position I.
WARNING
Never stand next to the tyre when the
compressor is running. If cracks or
unevenness arise then the compressor
must be switched off immediately. The
journey should not be continued. Contacting an authorised tyre centre is recommended.
9. Switch off the compressor to check the
pressure on the pressure gauge. Minimum pressure is 1.8 bar and maximum
3.5 bar. (Release air with the pressure
reducing valve if the tyre pressure is too
high.)
WARNING
8. Inflate the tyre for 7 minutes.
IMPORTANT
Risk of overheating. The compressor must
not run for more than 10 minutes.
Emergency puncture repair (p. 331), in which
the emergency puncture repair kit (p. 333)*
(TMK - Temporary Mobility Kit), is used to seal
a puncture and check and adjust the air pressure.
1. Connect the tyre sealing equipment
again.
2. Read the tyre pressure on the pressure
gauge.
10. Switch off the compressor and unplug the
cable from the 12 V socket.
11. Detach the hose from the tyre valve and
fit the valve cap.
12. As soon as possible, drive approximately
3 km at a maximum speed of 80 km/h so
that the sealing fluid can seal the tyre.
Related information
•
•
09
Check tyre pressure
If the pressure is below 1.8 bar then the
hole in the tyre is too big. The journey
should not be continued. Contacting an
authorised tyre centre is recommended.
NOTE
When the compressor starts, the pressure
can increase up to 6 bar but the pressure
drops after approximately 30 seconds.
Emergency puncture repair* rechecking
Emergency puncture repair* (p. 331)
Emergency puncture repair* - rechecking
(p. 335)
•
Emergency puncture repair kit* - overview
(p. 333)
•
Emergency puncture repair* - stowing
components (p. 337)
•
If it is below 1.3 bar then the tyre is
insufficiently sealed. The journey
should not be continued. Contact a
tyre centre.
•
If the tyre pressure is higher than 1.3
bar, the tyre must be inflated to the
tyre pressure specified in accordance
with the tyre pressure table found in
the printed owner's manual (1 bar =
100 kPa). Release air using the pressure reducing valve if the tyre pressure
is too high.
}}
* Option/accessory, for more information, see Introduction.
335
09 Wheels and tyres
09
||
WARNING
Do not unscrew the bottle, it is equipped
with a reverse catch to prevent leakage.
3. Make sure the compressor is switched
off. Detach the air hose and cable. Refit
the dust cap.
Volvo recommends that you drive to the nearest authorised Volvo workshop for the
replacement/repair of the damaged tyre.
Advise the workshop that the tyre contains
sealing fluid.
WARNING
You should not drive faster than 80 km/h
after the emergency tyre repair kit has
been used. Volvo recommends that you
visit an authorised Volvo workshop for
inspection of the sealed tyre (maximum
driving distance is 200 km). The staff there
can determine whether or not the tyre can
be repaired or if it needs to be replaced.
4. Fold the hose into the box and leave the
bottle where it is. Place TMK in the cargo
area.
NOTE
•
•
After a tyre has been inflated, always
refit the dust cap in order to avoid
damage to the valve from gravel, dirt,
etc.
Only use plastic dust caps. Metal dust
caps can rust and become difficult to
unscrew.
Related information
•
Emergency puncture repair* - operation
(p. 334)
•
Emergency puncture repair* - stowing
components (p. 337)
NOTE
The sealing fluid bottle and the hose must
be replaced after use. Volvo recommends
that this replacement is performed by an
authorised Volvo workshop.
WARNING
Check the tyre pressure regularly.
336
* Option/accessory, for more information, see Introduction.
Inflating tyres with the emergency
puncture repair kit*
The car's original tyres can be inflated using
the compressor in the emergency puncture
repair kit.
1. The compressor must be switched off.
Make sure that the switch is in position 0
and locate the cable and air hose.
2. Unscrew the wheel's dust cap and screw
in the air hose valve connection to the
bottom of the thread on the tyre's air
valve.
WARNING
Inhaling car exhaust fumes could result in
danger to life. Never leave the engine running in sealed areas or areas that lack sufficient ventilation.
WARNING
Do not leave children in the car without
supervision when the engine is running.
3. Connect the cable to one of the car's
12 V sockets and start the car.
4. Start the compressor by flicking the
switch to position I.
09 Wheels and tyres
IMPORTANT
Risk of overheating. The compressor must
not run for more than 10 minutes.
5. Inflate the tyre to the pressure specified in
accordance with the tyre pressure table
that is found in the printed owner's manual. (Release air using the pressure
reducing valve if the tyre pressure is too
high.)
09
Emergency puncture repair* - stowing
components
After using the puncture repair kit, the components returned to their correct places in the
foam block.
6. Switch off the compressor. Detach the air
hose and cable.
Version 2.
7. Refit the dust cap.
The components are fitted in the foam block
in the following order:
Related information
•
•
1. Socket wrench
Emergency puncture repair* (p. 331)
Emergency puncture repair kit* - overview
(p. 333)
2. Towing eye
Version 1.
The components are fitted in the foam block
in the following order:
1. Towing eye/socket wrench
2. Bottle (pressed in from the side)
3. TMK kit
4. Funnel
5. Jack
6. Torx wrench
7. Towbar
3. Bottle
4. TMK kit
5. Jack
Related information
•
•
Emergency puncture repair* (p. 331)
Emergency puncture repair* - operation
(p. 334)
•
Emergency puncture repair* - rechecking
(p. 335)
•
Emergency puncture repair kit* - overview
(p. 333)
* Option/accessory, for more information, see Introduction.
337
09 Wheels and tyres
09
Emergency puncture repair kit* sealant
The container (bottle) with the emergency
puncture repair kit (p. 333) contains sealant
and it can be replaced.
Replace the bottle when the expiration date
has passed. Treat the old bottle as environmentally hazardous waste.
WARNING
The bottle contains 1.2-Ethanol and natural rubber-latex.
Harmful if ingested. Could result in allergic
reaction in the event of skin contact.
Avoid contact with the skin and eyes.
Store out of the reach of children.
Related information
•
•
338
Emergency puncture repair* (p. 331)
Emergency puncture repair kit* - location
(p. 332)
* Option/accessory, for more information, see Introduction.
09 Wheels and tyres
09
Type approval - tyre pressure
monitoring
Type approval of the sensors in tyre pressure
monitoring - TPMS (Tyre Pressure Monitoring
System)* can be read in the table.
}}
* Option/accessory, for more information, see Introduction.
339
09 Wheels and tyres
09
||
Country/Area
Brazil
Ukraine
340
09 Wheels and tyres
Country/Area
09
Israel
}}
341
09 Wheels and tyres
09
||
Declaration of Conformity (Declaration of Conformity)
Country/
Area
Countries in
the EU:
Exporting country: Germany
Manufacturer: Continental Automotive GmbH
Type of equipment: TPMS unit
342
09 Wheels and tyres
09
Country/
Area
Czech Republic:
Continental tímto prohlašuje, že tento Radio Transmitter je ve shodě se základními požadavky a dalšími příslušnými
ustanoveními směrnice 1999/5/ES.
Denmark:
Undertegnede Continental erklærer herved, at følgende udstyr Radio Transmitter overholder de væsentlige krav og øvrige
relevante krav i direktiv 1999/5/EF.
Germany:
Hiermit erklärt Continental, dass sich das Gerät Radio Transmitter in Übereinstimmung mit den grundlegenden Anforderungen
und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Estonia:
Käesolevaga kinnitab Continental seadme Radio Transmitter vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud
direktiivist tulenevatele teistele asjakohastele sätetele.
UK
Hereby, Continental declares that this Radio Transmitter is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Spain:
Por medio de la presente Continental declara que el Radio Transmitter cumple con los requisitos esenciales y cualesquiera
otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Greece:
ΜΕ ΗΝ ΠΑΡΟ ΣΑ Continental ΗΛΩΝΕ Ο Radio Transmitter Σ ΜΜΟΡΦΩΝΕ Α ΠΡΟΣ
Σ ΛΟ ΠΕΣ ΣΧΕ
ΕΣ Α ΑΞΕ Σ ΗΣ Ο Η ΑΣ 1999/5/Ε .
France:
Par la présente Continental déclare que l'appareil Radio Transmitter est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE.
Italy:
Con la presente Continental dichiara che questo Radio Transmitter è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 1999/5/CE.
Latvia:
Ar šo Continental deklarē, ka Radio Transmitter atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem
noteikumiem.
Lithuania:
Šiuo Continental deklaruoja, kad šis Radio Transmitter atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Netherlands:
Hierbij verklaart Continental dat het toestel Radio Transmitter in overeenstemming is met de essentiële eisen en de andere
relevante bepalingen van richtlijn 1999/5/EG.
Σ Ο Σ Ω Ε Σ ΑΠΑ ΗΣΕ Σ Α
}}
343
09 Wheels and tyres
09
||
Country/
Area
Malta:
Hawnhekk, Continental, jiddikjara li dan Radio Transmitter jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn
relevanti li hemm fid-Dirrettiva 1999/5/EC.
Hungary:
Alulírott, Continental nyilatkozom, hogy a Radio Transmitter megfelel a vonatkozó alapvetõ követelményeknek és az
1999/5/EC irányelv egyéb elõírásainak.
Poland:
Niniejszym Continental oświadcza, że Radio Transmitter jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi
postanowieniami Dyrektywy 1999/5/EC.
Portugal:
Continental declara que este Radio Transmitter está conforme com os requisitos essenciais e outras disposições da Directiva
1999/5/CE.
Slovenia:
Continental izjavlja, da je ta Radio Transmitter v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive
1999/5/ES.
Slovakia:
Continental týmto vyhlasuje, že Radio Transmitter spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice
1999/5/ES.
Finland:
Continental vakuuttaa täten että Radio Transmitter tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen mukainen.
Sweden:
Härmed intygar Continental att denna Radio Transmitter står I överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Iceland:
Hér með lýsir Continental yfir því að Radio Transmitter er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun
1999/5/EC.
Norway:
Continental erklærer herved at utstyret Radio Transmitter er i samsvar med de grunnleggende krav og øvrige relevante krav i
direktiv 1999/5/EF.
Related information
•
344
Tyre pressure monitoring* (p. 324)
* Option/accessory, for more information, see Introduction.
MAINTENANCE AND SERVICE
10 Maintenance and service
10
Volvo service programme
Book service and repair*1
To keep the car as safe and reliable as possible, follow the Volvo service programme as
specified in the Service and Warranty Booklet.
Manage service, repair and booking information directly in your Internet-connected car.
Volvo recommends engaging an authorised
Volvo workshop to perform the service and
maintenance work. Volvo workshops have the
personnel, special tools and service literature
to guarantee the highest quality of service.
IMPORTANT
For the Volvo warranty to apply, check and
follow the instructions in the Service and
Warranty Booklet.
Related information
•
1
2
346
Climate control system - fault tracing and
repair (p. 359)
This service provides a convenient way to
book a service and workshop visit directly in
the car. Car information is sent to your dealer,
who can prepare the workshop visit. The
dealer will contact you to schedule an
appointment time. For certain markets, the
system reminds you of a scheduled appointment time as it approaches and the navigation system2 can also guide you to the workshop when the time comes.
–
Prerequisite for booking from car
•
To send and receive booking information
to and from the car, the car must be connected to the Internet, see Sensus Infotainment supplement for information on
how to connect the car to the Internet.
•
Since the booking information is sent
over your private phone subscription, you
will be asked whether you want to send
the information. The question is asked
once and then applies to the selected
connection for a limited time.
•
For the service to work and for the system to communicate via the car's screen,
notifications/pop-up messages must be
accepted. In the normal view for the MY
CAR source, press OK/MENU and then
Service & repair Display
notifications.
Before the service can be used
Volvo ID and my profile
•
Register a Volvo ID. For more information
and how to create a Volvo ID, see Volvo
ID (p. 20).
•
Log in to the web portal My Volvo, go to
your profile and carry out the following:
–
Check that the car is connected to your
profile.
–
Check that your contact information is
correct.
–
Select the Volvo dealer you want to contact for service and repair.
Applies to certain markets.
Applies to Sensus Navigation.
* Option/accessory, for more information, see Introduction.
Select preferred communication channel
(SMS or phone). Booking information is
always sent to the car and to you via
email.
Using the service
All menus and settings are accessed from the
normal view in MY CAR by pressing OK/
MENU and then Service & repair.
When it is time for service, and in some cases
when the car is in need of repair, this is noti-
10 Maintenance and service
fied in the combined instrument panel (p. 61)
and via a pop-up menu in the screen.
Book a service or repair manually1
Call the dealer1
1. Press the MY CAR button in the centre
console and select Service & repair
Dealer information Request service
or repair.
> Vehicle data is sent automatically to
your dealer.
With a Bluetooth® phone connected to the
car, you can call your dealer. For connecting
the phone, see Sensus Infotainment supplement.
2. The dealer sends a booking proposal to
the car.
Using the navigation system1, 2
3. Accept or request a new booking proposal.
Service message in the screen.
Meaning of the answer options in the
screen's pop-up menu:
• Yes - A booking enquiry is sent to your
dealer who then comes back with a
booking proposal. The service lamp and
service message in the combined instrument panel are extinguished.
• No - No more pop-up messages will be
shown in the screen. The message in the
combined instrument panel remains. After
this option has been selected, it is possible to start the manual booking in the car,
see below.
After the booking has been accepted the
booking information is stored in the car, see
My bookings. The car will automatically communicate with you via the screen by means of
reminders about the booking and guide you
to the workshop visit.
You can also book a workshop visit via My
Volvo. Go to "My bookings" and select
"Update" in order to gain access to bookings
from My Volvo.
My bookings1
Show booking information in the car's screen.
Accept or request a new booking proposal.
–
Select Service & repair
My bookings.
–
10
Select Service & repair Dealer
information Call dealer.
Enter your workshop as destination or waypoint in the navigation system.
–
Select Service & repair Dealer
information Set single destination.
–
Select Service & repair Dealer
information Add as waypoint.
Sending vehicle data1
Vehicle data is sent to a central Volvo database (not your dealer) from which Volvo dealers can retrieve vehicle information using the
car's identification number (VIN3). The number is printed in the car's service and warranty booklet, alternatively inside the windscreen's bottom left-hand corner.
–
Select Service & repair
data.
Send car
• Postpone - The pop-up menu is shown
the next time the car is started.
1
2
3
Applies to certain markets.
Applies to Sensus Navigation.
Vehicle Identification Number
}}
347
10 Maintenance and service
||
Booking information and vehicle data
10
When you decide to book a service from your
car, the booking information and vehicle data
will be sent. Vehicle data information consists
of a number of signals within the following
areas:
•
•
•
•
•
Service requirement.
•
The car's software version.
Function status.
Fluid levels.
Mileage (distance).
The car's vehicle identification number
(VIN3).
Related information
•
3
348
Volvo ID (p. 20)
Vehicle Identification Number
10 Maintenance and service
Raising the car
When raising the car it is important that the
jack or lifting arms are fitted in the intended
points on the car's underbody.
NOTE
10
Volvo recommends only using the jack that
belongs to the car model in question. If a
jack is selected other than the one recommended by Volvo, follow the instructions
supplied with the equipment.
}}
349
10 Maintenance and service
||
10
Jacking points (arrows) for the jack that belongs to the car and lifting points (marked in red).
If the car is raised with a front workshop jack
then this must be positioned under one of the
two lifting points furthest in under the car. If
the car is raised with a rear workshop jack
then it must be positioned under one of the
lifting points. Ensure that the workshop jack
is positioned so that the car cannot slide off
the jack. Always use axle stands or similar.
If the car is raised with a two-pillar workshop
lift then the front and rear lifting arms can be
positioned under the outer lifting points (jacking points). Alternatively, the inner lifting
points can be used at the front.
Related information
•
350
Changing wheels - removing wheels
(p. 319)
10 Maintenance and service
Bonnet - opening and closing
Turn the handle about 20-25 degrees
clockwise. You will hear when the catch
releases.
The bonnet can be opened when the handle
in the passenger compartment has been
turned clockwise and the lock by the grille has
been moved to the left.
Move the catch to the left and open the
bonnet. (The catch hook is located
between the headlamp and grille, see
illustration.)
The bonnet can be opened when the handle
in the passenger compartment has been
turned clockwise and the lock by the grille has
been moved to the left.
Engine compartment - overview
The overview shows normal checking points.
Engine compartment 4-cyl. 2.0 l
10
WARNING
Check that the bonnet locks properly when
closed.
Related information
•
•
Engine compartment - checking (p. 352)
Engine compartment - overview (p. 351)
The appearance of the engine compartment may
differ depending on engine variant.
Coolant expansion tank
The handle for bonnet opening is always on the
left-hand side.
Filling washer fluid
Radiator
Filling engine oil
Reservoir for brake and clutch fluid
(located on the driver's side)
Starter battery
Relay and fuse box
Air filter
}}
351
10 Maintenance and service
||
WARNING
The ignition system has very high voltage
and output. The voltage in the ignition system is highly dangerous. The car's electrical system must always be in key position
0 when work is being performed in the
engine compartment; see Key positions functions at different levels (p. 76).
10
Radiator
Engine compartment - checking
Engine oil dipstick4
Some oils and fluids should be checked at
regular intervals.
Filling engine oil
Do not touch the spark plugs or ignition
coil when the car's electrical system is in
key position II or when the engine is hot.
Regular checking
Reservoir for brake and clutch fluid
(located on the driver's side)
Check the following oils and fluids at regular
intervals, e.g. when refuelling:
Starter battery
•
•
•
Relay and fuse box
Air filter
WARNING
Remember that the radiator fan (located at
the front of the engine compartment,
behind the radiator) may start automatically some after the engine has been
switched off.
The ignition system has very high voltage
and output. The voltage in the ignition system is highly dangerous. The car's electrical system must always be in key position
0 when work is being performed in the
engine compartment; see Key positions functions at different levels (p. 76).
Do not touch the spark plugs or ignition
coil when the car's electrical system is in
key position II or when the engine is hot.
Related information
Coolant expansion tank
•
•
Bonnet - opening and closing (p. 351)
Engine compartment - checking (p. 352)
Filling washer fluid
4
352
Washer fluid
WARNING
Engine compartment, apart from 4-cyl.
2.0 l
The appearance of the engine compartment may
differ depending on engine variant.
Coolant
Engine oil
Engines with electronic oil level sensor do not have a dipstick (5-cyl. diesel).
Always have the engine cleaned by a
workshop - an authorised Volvo workshop
is recommended. There is a risk of fire if
the engine is hot.
Related information
•
•
•
•
•
Bonnet - opening and closing (p. 351)
Engine compartment - overview (p. 351)
Coolant - level (p. 357)
Engine oil - checking and filling (p. 354)
Washer fluid - filling (p. 369)
10 Maintenance and service
Engine oil - general
An approved engine oil must be used in order
that the recommended service intervals can
be applied.
When driving under adverse conditions, see
Engine oil - adverse driving conditions
(p. 399).
IMPORTANT
In order to fulfil the requirements for the
engine's service intervals all engines are
filled with a specially adapted synthetic
engine oil at the factory. The choice of oil
has been made very carefully with regard
to service life, starting characteristics, fuel
consumption and environmental impact.
Volvo recommends:
An approved engine oil must be used in
order that the recommended service intervals can be applied. Only use a prescribed
grade of oil for both filling and oil change,
otherwise you will risk affecting service life,
starting characteristics, fuel consumption
and environmental impact.
tain variants have both systems. Contact a
Volvo dealer for more information.
Change the engine oil and oil filter in accordance with the intervals specified in the Service and Warranty Booklet.
10
Using oil of a higher than specified grade is
permitted. If the car is driven in adverse conditions, Volvo recommends using an oil of a
higher grade; see Engine oil - adverse driving
conditions (p. 399).
For filling capacities, see Engine oil - grade
and volume (p. 400).
Related information
•
Engine oil - checking and filling (p. 354)
Volvo Car Corporation disclaims all warranty liability if engine oil of the prescribed
grade and viscosity is not used.
Volvo recommends that oil changes are
carried out at an authorised Volvo workshop.
Volvo uses different systems for warning of
low/high oil level or low oil pressure. Certain
engine variants have an oil pressure sensor,
and then the combined instrument panel's
warning symbol for low oil pressure is used.
Other variants have an oil level sensor, when
the driver is informed via the instrument's
warning symbol
and display texts. Cer-
353
10 Maintenance and service
Engine oil - checking and filling
WARNING
Engine with oil dipstick5
Never fill above the MAX mark. The level
should never be above MAX or below MIN
as this could lead to engine damage.
G021737
10
6. If required, check the level again, do it
after driving a short distance. Then repeat
steps 1 - 4.
Depending on engine variant the oil level is
checked with the dipstick or the electronic oil
level sensor.
The oil level must be between the MIN and MAX
marks.
Measurement and filling if required
Dipstick and filler pipe.
Checking the oil level in a new car is especially important before the first scheduled oil
change.
2. Pull up and wipe the dipstick.
Volvo recommends checking the oil level
every 2 500 km. The most accurate measurements are made on a cold engine before starting. The measurement will be inaccurate if
taken immediately after the engine is
switched off. The dipstick will indicate that
the level is too low because the oil has not
had time to flow down into the oil sump.
4. Pull it out and check the level.
5
6
354
1. Ensure that the car is level. After switching off the engine it is important to wait
5 minutes to allow the oil time to run back
to the sump.
WARNING
Do not spill oil onto the hot exhaust manifold due to the risk of fire.
Engine with electronic oil level sensor,
4-cyl. 2.0 l
3. Re-insert the dipstick.
5. If the level is close to MIN then 0.5 litres
should be added. If the level is significantly below, then an additional amount
is required.
Does not apply to the 4-cyl. 2.0 litre or 5-cyl. diesel, which have electronic oil level sensor.
Engines with electronic oil level sensor do not have a dipstick.
Filler pipe6.
10 Maintenance and service
You do not need to take action with respect
to the engine oil level before a message is
shown in the display, see following illustration.
WARNING
If the message Oil service required is
shown, visit a workshop. The oil level may
be too high.
IMPORTANT
If notified of low oil level, only fill with the
volume specified, for example, 0.5 litres.
NOTE
Message and graph in the display. The left-hand
display shows the digital combined instrument
panel and the right-hand the analogue.
Message
Engine oil level
The oil level is checked using the electronic
oil level gauge with the thumbwheel when the
engine is switched off, see Menu navigation combined instrument panel (p. 105).
The system cannot directly detect changes
when the oil is filled or drained. The car
must have been driven approx. 30 km and
have been stationary for 2 hours with the
engine switched off and on level ground
before oil level indication is correct.
2. Rotate the thumbwheel on the left-hand
stalk switch to position Oil level.
> You will then see information displayed
about the engine oil level.
For more information on menu navigation, see Menu navigation - combined
instrument panel (p. 105).
10
NOTE
If the right conditions for measuring the oil
level are not met (time after engine shutdown, the car's inclination, outside temperature, etc.) then the message Not
available will be shown. This does not
mean that there is something wrong in the
car's systems.
WARNING
Do not spill oil onto the hot exhaust manifold due to the risk of fire.
Measuring the oil level, 4-cyl. 2.0 l
If the oil level needs to be checked then it
should be carried out in accordance with the
sequence below.
1. Activate key position II; see Key positions
- functions at different levels (p. 76).
}}
355
10 Maintenance and service
||
Engine with electronic oil level sensor,
5-cyl. diesel
NOTE
The oil level is only detected by the system
during driving. The system cannot directly
detect changes when the oil is filled or
drained. The car must be driven
about 30 km before the oil level display is
correct.
10
WARNING
Filler pipe7.
You do not need to take action with respect
to the engine oil level before a message is
shown in the combined instrument panel's
information display, see following illustration.
Message and graph in the display. The left-hand
display shows the digital combined instrument
panel and the right-hand the analogue.
Message
Engine oil level
On certain cars, the oil level can be checked
using the electronic oil level gauge with the
thumbwheel when the engine is switched off.
WARNING
If the message Oil service required is
shown, visit a workshop. The oil level may
be too high.
IMPORTANT
In the event of the message Oil level low
Refill 0.5 litre, only fill with 0.5 litres.
7
356
Engines with electronic oil level sensor do not have a dipstick.
Do not fill more oil if filling level (3) or (4)
appears as shown in the illustration below.
The level must never be above MAX or
below MIN, as this could lead to engine
damage.
WARNING
Do not spill oil onto the hot exhaust manifold due to the risk of fire.
10 Maintenance and service
Measuring the oil level, 5-cyl. diesel
If the oil level needs to be checked then it
should be carried out in accordance with the
sequence below.
1. Activate key position II; see Key positions
- functions at different levels (p. 76).
2. Rotate the thumbwheel on the left-hand
stalk switch to position Oil level.
> You will then see information displayed
about the engine oil level.
Related information
•
•
Engine oil - general (p. 353)
Key positions - functions at different levels (p. 76)
Coolant - level
The coolant cools the internal combustion
engine to the correct operating temperature.
The heat that is transferred from the engine to
the coolant can be used to heat the passenger compartment.
10
The coolant level must lie between the MIN
and MAX marks on the expansion tank.
Checking the level and topping up
For more information on menu navigation, see Menu navigation - combined
instrument panel (p. 105).
The figures 1-4 represent filling level. Do not fill
more oil if filling level (3) or (4) is shown. The recommended filling level is 4. Message and graph
in the display. The left-hand display shows the
digital combined instrument panel and the righthand the analogue.
When topping up the coolant, follow the
instructions on the packaging. It is important
that the mixture of coolant concentrate and
water is correct for the prevailing weather
conditions. Never top up with water only. The
risk of freezing increases with both too little
and too much coolant concentrate.
}}
357
10 Maintenance and service
||
WARNING
10
Coolant can be very hot. If the coolant
requires topping up when the engine is at
operating temperature, unscrew the
expansion tank cap slowly to gently
release the overpressure.
For capacities and for standards regarding
water quality; see Coolant - grade and volume (p. 402).
IMPORTANT
•
A high content of chlorine, chlorides
and other salts may cause corrosion in
the cooling system.
•
Always use coolant with anti-corrosion
agent as recommended by Volvo.
•
Ensure that the coolant mixture is 50%
water and 50% coolant.
•
Mix the coolant with approved quality
tap water. In the event of any doubt
about water quality, used ready-mixed
coolant in accordance with Volvo recommendations.
Check the coolant regularly
The level must lie between the MIN and MAX
marks on the expansion tank. If the system is
not filled sufficiently, high temperatures could
occur, causing a risk of damage to the
engine.
•
•
358
When changing coolant/replacing
cooling system components, flush the
cooling system clean with approved
quality tap water or flush with readymixed coolant.
The engine must only be run with a
well-filled cooling system. Otherwise,
temperatures that are too high may
occur resulting in the risk of damage
(cracks) in the cylinder head.
Brake and clutch fluid - level
Brake and clutch fluid level should be
between the reservoir MIN and MAX marks.
Checking the level
Brake and clutch fluid have a common reservoir. The level must be between the MIN and
MAX marks that are visible inside the reservoir. Check the level regularly.
Change the brake fluid every other year or at
every other regular service.
The fluid should be changed annually on cars
driven in conditions requiring hard, frequent
braking, such as driving in mountains or tropical climates with high humidity.
For capacities and recommended brake fluid
grade, see Brake fluid - grade and volume
(p. 404).
WARNING
If the brake fluid is below the MIN level in
the brake fluid reservoir, do not drive further before topping up the brake fluid.
Volvo recommends that the reason for the
loss of brake fluid is investigated by an
authorised Volvo workshop.
10 Maintenance and service
Filling
Climate control system - fault tracing
and repair
The air conditioning system must only be
serviced and repaired by an authorised workshop.
Troubleshooting and repair
The air conditioning system contains fluorescent tracing agents. Use ultraviolet light when
looking for leaks.
Volvo recommends that you contact an
authorised Volvo workshop.
The fluid reservoir is located on the driver's side.
WARNING
Unscrew the reservoir cap and fill the fluid.
The level must be between the MIN and MAX
marks, which are located on the inside of the
reservoir.
IMPORTANT
Do not forget to refit the cap.
8
9
10
LED (Light Emitting Diode)
An authorised Volvo workshop is recommended.
Certain variants.
The air conditioning system contains pressurised refrigerant R134a. This system
must only be serviced and repaired by an
authorised workshop.
Related information
•
Volvo service programme (p. 346)
Lamp replacement - general
Lamp replacement can be carried out for
bulbs. When replacing LED and Xenon lamps,
please refer to a workshop.
The bulbs are specified (p. 366). The following list contains locations of bulbs and other
light sources that are specialised, such as
LED8 lamps, or are unsuitable for changing
for some other reason, except at a workshop9:
•
active xenon headlamps - ABL (xenon
lamps)
•
•
•
•
•
•
•
•
•
•
position/parking lamps front10
10
daytime running light lamps10
side direction indicators, door mirrors10
approach lighting, door mirrors
interior and cargo area lighting
glovebox lighting
position/parking lamps rear
side marker lamps rear
brake light above the rear windscreen
number plate lighting.
}}
359
10 Maintenance and service
||
WARNING
10
NOTE
On cars with Xenon headlamps, the
replacement of Xenon lamps must be carried out at a workshop - an authorised
Volvo workshop is recommended. Working
with Xenon lamps demands extreme caution because the headlamp is equipped
with a high voltage unit.
WARNING
The car’s electrical system must be in key
position 0 when replacing bulbs; see Key
positions - functions at different levels
(p. 76).
IMPORTANT
Never touch the glass part of the bulbs
with your fingers. Grease from your fingers
is vaporised by the heat, coating the
reflector and then causing damage.
Outside lighting such as headlamps, fog
lamps and rear lamps may temporarily
have condensation on the inside of the
lens. This is normal, all exterior lighting is
designed to withstand this. Condensation
is normally vented out of the lamp housing
when the lamp has been switched on for a
time.
Lamp replacement - location of front
lamps
The overview shows the location of the lamps
at the front.
Related information
•
•
Lamps - specifications (p. 366)
Lamp replacement - location of front
lamps (p. 360)
•
Lamp replacement - location of rear
lamps (p. 364)
•
Lamp replacement - vanity mirror lighting
(p. 365)
Position/parking lamps (p. 363) (LED in
Xenon headlamps)
Main beam in Xenon headlamps
(p. 362) / Extra main beam in Xenon
headlamps (p. 362)
NOTE
Dipped beam in halogen headlamps
(p. 362) / Xenon lamps in Xenon headlamps (p. 359)
If an error message remains after the broken bulb has been replaced then we recommend that you visit an authorised Volvo
workshop.
Indicator (p. 363)
Daytime running lights (p. 363) (LED* or
bulb depending on variant)
Related information
•
•
360
* Option/accessory, for more information, see Introduction.
Lamp replacement - general (p. 359)
Lamps - specifications (p. 366)
10 Maintenance and service
Lamp replacement - headlamps
5.
All of the headlamp bulbs are replaced via the
engine compartment. First loosen and remove
the whole headlamp.
Press down the catch.
Unplug the connector.
Place the headlight on a soft surface so
as not to scratch the lens.
Lamp replacement - cover for main/
dipped beam bulbs
Main/dipped beam bulbs are accessed by
releasing the headlamp's larger cover.
10
IMPORTANT
Do not pull the electrical cable, only the
connector.
6. Replace the relevant bulb as instructed.
The headlight must be fitted and the contact
fitted correctly before switching on the lights
or switching key position.
Related information
1.
2.
3.
Lift out the bonnet stop.
Loosen the screw with a Torx tool,
size T30.
Turn the locking pin anticlockwise.
Pull out the locking pin.
4.
Release the headlamp by alternately
tilting and pulling it out.
IMPORTANT
Take care when lifting out the headlamp so
as not to damage any parts.
•
•
Lamp replacement - general (p. 359)
•
Lamp replacement - cover for main/
dipped beam bulbs (p. 361)
•
Lamps - specifications (p. 366)
Lamp replacement - location of front
lamps (p. 360)
1.
Press the hooks together.
Angle out the cover.
2. Replace the relevant bulb as instructed.
Related information
•
•
•
•
Lamp replacement - headlamps (p. 361)
Lamp replacement - dipped beam
(p. 362)
Lamp replacement - main beam (p. 362)
Lamp replacement - extra main beam
(p. 362)
361
10 Maintenance and service
Lamp replacement - dipped beam
Lamp replacement - main beam
Lamp replacement - extra main beam
The dipped beam bulb is fitted inside the
headlamp's larger cover.
The main beam bulb is fitted inside the headlamp's larger cover.
The extra main beam bulb is fitted inside the
headlamp's larger cover.
NOTE
10
NOTE
Applies to cars with halogen headlamps.
Applies to cars with halogen headlamps.
Applies to cars with Xenon headlamps*.
1. Detach the headlamp (p. 361).
1. Detach the headlamp (p. 361).
1. Detach the headlamp (p. 361).
2. Undo the cover (p. 361).
2. Undo the cover (p. 361).
2. Undo the cover (p. 361).
3.
3.
3.
Press the bulb holder upwards until it
releases.
Pull out the bulb holder.
4. Replace the bulb and put back the parts
in reverse order.
Related information
•
362
NOTE
Lamps - specifications (p. 366)
Turn the bulb holder anticlockwise.
Pull out the bulb holder.
4. Replace the bulb and put back the parts
in reverse order.
Related information
•
* Option/accessory, for more information, see Introduction.
Lamps - specifications (p. 366)
Press the bulb holder upwards until it
detaches.
Pull out the bulb holder.
4. Replace the bulb and put back the parts
in reverse order.
Related information
•
Lamps - specifications (p. 366)
10 Maintenance and service
Lamp replacement - direction
indicators front
Lamp replacement - position/parking
lamps front
Lamp replacement - daytime running
lights
The direction indicator lamp is fitted inside
the headlamp's smaller cover.
The position/parking lamp bulb holder is
located on the side of the headlamp.
The daytime running light bulb is fitted inside
the bumper's cover.
NOTE
NOTE
Not applicable to cars with Xenon headlamps* as these are equipped with LED
lamps.
10
Only applies to daytime running lights with
bulbs.
1. Detach the headlamp (p. 361).
2.
Undo the cover.
3.
Push in the catch.
Pull out the bulb holder.
4. Replace the bulb and put back the parts
in reverse order.
1. Detach the headlamp (p. 361).
2.
Related information
•
Lamps - specifications (p. 366)
Turn the bulb holder anticlockwise.
3. Replace the bulb and put back the parts
in reverse order.
•
Lamps - specifications (p. 366)
Undo the cover.
2.
Turn the bulb holder anticlockwise.
Pull out the bulb holder.
Pull out the bulb holder.
Related information
1.
3. Replace the bulb and put back the parts
in reverse order.
Related information
•
Lamps - specifications (p. 366)
* Option/accessory, for more information, see Introduction.
363
10 Maintenance and service
Lamp replacement - location of rear
lamps
10
The overview shows the location of the lamps
at the rear.
Lamp replacement - direction
indicators rear, brake lights and
reversing lamp
Related information
•
Lamp replacement - location of rear
lamps (p. 364)
Direction indicators rear, brake lights and
reversing lamp are replaced from inside the
cargo area.
•
Lamps - specifications (p. 366)
Brake light (LED)
Position/parking lights (LED)
Brake light (p. 364)
1. Remove the hatch in the upholstery (1) on
the same side as the defective bulb.
Side marker lamps (LED)
2.
Indicator (p. 364)
Reversing lamp (p. 364)
Fog lamp (p. 365)
Related information
•
•
364
Lamp replacement - general (p. 359)
Lamps - specifications (p. 366)
Press the catch sideways.
Pull out the bulb holder.
3. Remove the blown bulb by pressing it in
and turning anticlockwise.
4. Replace the bulb and put back the parts
in reverse order.
10 Maintenance and service
Lamp replacement - rear fog lamp
Turn the bulb holder anticlockwise.
The fog lamp bulb is fitted in the bumper's
bulb holder.
Pull out the bulb holder.
3. Replace the bulb and put back the parts
in reverse order.
Lamp replacement - vanity mirror
lighting
The vanity mirror's lamps are fitted inside the
lamp lenses.
10
Related information
•
Lamps - specifications (p. 366)
1. Insert a screwdriver under the lamp lens
and gently prize up the lug on the edge.
2. Carefully detach and lift aside the lamp
lens.
Insert (approx.20 mm) a blunt, knife-like
object, e.g. a table knife, at the triangle.
Carefully prise until the lug releases.
IMPORTANT
Take care not to damage any parts.
3. Using needle-nose pliers, pull the bulb
straight out to the side. Do not squeeze
too hard with the pliers. Otherwise, the
bulb glass could break.
4. Replace the bulb and put back the parts
in reverse order.
Related information
•
Lamps - specifications (p. 366)
365
10 Maintenance and service
Lamps - specifications
10
Lighting
[W]A
Type
55
H7 LL
Main beamB
65
H9
Additional main
beamC
55
H7 LL
Front direction
indicators
21
HY21W
Position/parking
lamps frontB
5
W5W LL
Daytime running
lightsD
19
PW19W
Side direction indicators, door mirrorsD
5
WY5W LL
Direction indicators, rear
21
PY21W LL
Brake light
21
P21W LL
Dipped
beamB
Reversing lamp
366
Lighting
The specifications apply to bulbs. When
replacing LED and Xenon lamps, please refer
to a workshop.
21
P21W LL
[W]A
Type
Rear fog lamp
21
H21W LL
Vanity mirror lighting
1.2
T5 Socket
W2x4.6d
A
B
C
D
Watt
Cars with halogen headlights
Cars with xenon headlights
Certain variants
Wiper blades
The wiper blades sweep water away from the
windscreen and rear window. Together with
the washer fluid they clean the windows and
ensure visibility for driving.
The windscreen wiper blades must be in service position when they are to be replaced.
Service position
Related information
•
•
Lamp replacement - general (p. 359)
•
Lamp replacement - location of rear
lamps (p. 364)
•
Lamp replacement - vanity mirror lighting
(p. 365)
Lamp replacement - location of front
lamps (p. 360)
Wiper blades in service position.
In order to change, clean or lift the wiper
blades (for scraping off ice from the windscreen, for example) they must be in service
position.
IMPORTANT
Before placing the wiper blades in the
service position, make sure that they are
not frozen down.
10 Maintenance and service
1. Insert the remote control key in the ignition switch11 and briefly press the
START/STOP ENGINE button to set the
car's electrical system to key position I.
For detailed information on key positions,
see Key positions - functions at different
levels (p. 76).
2. Briefly press the START/STOP ENGINE
button again to set the car’s electrical
system in key position 0.
3. Within 3 seconds, move the right stalk
switch up and hold it in position for
approx. 1 second.
> The wipers then move to standing
straight up.
The wipers return to their starting position
when you briefly press the START/STOP
ENGINE button to set the car’s electrical system to key position I (or when the car is
started).
IMPORTANT
If the wiper arms in the service position
have been folded up from the windscreen,
they must be folded back down onto the
windscreen before the wipers are allowed
to return to their starting position. This is to
avoid scraping the paint on the bonnet.
11
Not necessary in cars with the Keyless function.
Replacing the wiper blades
10
Fold up the wiper arm when it is in service position. Press the button located on
the wiper blade mounting and pull
straight out parallel with the wiper arm.
Slide in the new wiper blade until a "click"
is heard.
Check that the blade is firmly installed.
4. Fold the wiper arm back towards the
windscreen.
The wipers return from service position to
their starting position when you briefly press
the START/STOP ENGINE button to set the
car’s electrical system to key position I (or
when the car is started).
}}
367
10 Maintenance and service
||
Replacing the wiper blades, rear
window
IMPORTANT
Check the blades regularly. Neglected
maintenance shortens the service life of
the wiper blades.
10
Related information
G021763
•
NOTE
The wiper blades are different lengths. The
blade on the driver's side is longer than on
the passenger side.
WARNING
Since the car is equipped with airbag
Pedestrian Airbag, Volvo recommends that
genuine wiper arms are used and that you
only use genuine parts for them.
1. Fold out the wiper arm.
2. Grip the inner section of the blade (by the
arrow).
3. Turn anticlockwise to use the blade's end
position against the wiper arm as a lever
to detach the blade more easily.
4. Press the new wiper blade into position.
Check that it is firmly installed.
5. Lower the wiper arm.
Cleaning
For cleaning wiper blades and windscreen,
see Car washing (p. 385).
368
Washer fluid - filling (p. 369)
10 Maintenance and service
Washer fluid - filling
Washer fluid is used for cleaning the headlamps and windows. Washer fluid with antifreeze must be used during winter.
Related information
•
Wiper blades (p. 366)
Starter battery - general
The starter battery is used to drive the starter
motor and other electrical equipment in the
car.
The service life and function of the starter battery is influenced by factors such as the number of starts, discharging, driving style, driving
conditions, climatic conditions etc.
10
The starter battery is a traditional 12 V battery.
The windscreen and headlamp washers share
a common reservoir.
IMPORTANT
Use Volvo genuine washer fluid or equivalent with a recommended pH of between 6
and 8.
•
Never disconnect the starter battery when
the engine is running.
•
Check that the cables to the starter battery are correctly connected and properly
tightened.
The following table shows specifications for
the starter battery.
Voltage (V)
Cold start
capacityA CCAB (A)
12
720C
760D
or 800D
IMPORTANT
Use washer fluid with antifreeze during the
winter to avoid freezing in the pump, reservoir and hoses.
For capacities, see Washer fluid - quality and
volume (p. 404).
}}
369
10 Maintenance and service
||
Size , L×W×H
(mm)
10
Capacity (Ah)
A
B
C
D
278×175×190D
or
315×175×190D
•
The battery can generate oxyhydrogen
gas, which is highly explosive. A spark
can be formed if a jump lead is connected incorrectly, and this can be
enough for the battery to explode.
•
The battery contains sulphuric acid,
which can cause serious burns.
•
If sulphuric acid comes into contact
with eyes, skin or clothing, flush with
large quantities of water. If acid
splashes into the eyes - seek medical
attention immediately.
70C
70D or 80D
According to EN standard.
Cold Cranking Amperes.
Manual gearbox.
Automatic gearbox. The specification is dependent on the
model variant.
IMPORTANT
If the starter battery is replaced, make sure
you replace it with a battery with the same
cold starting capacity and type as the original battery (see the label on the battery).
NOTE
370
WARNING
278×175×190C
•
The battery's container size should be
consistent with the original battery's
dimensions.
•
The battery's height is different
depending on size.
IMPORTANT
When charging the starter battery or the
support battery (p. 372), only use a modern battery charger with controlled charging voltage. Fast charging function must
not be used since it may damage the battery.
IMPORTANT
If the following instruction is not observed
then the energy saving function for infotainment system may be temporarily disengaged, and/or the message in the combined instrument panel's information display about the starter battery's state of
charge may be temporarily inapplicable,
following the connection of an external
battery or battery charger:
•
The negative battery terminal on the
car's starter battery must never be
used for connecting an external battery or battery charger - only the car
chassis may be used as the grounding point.
See Jump starting (p. 268) for a description of how the cable clamps must be
attached.
10 Maintenance and service
NOTE
The life of the battery is shortened if it
becomes discharged repeatedly.
The life of the battery is affected by several
factors, including driving conditions and
climate. Battery starting capacity decreases gradually with time and therefore
needs to be recharged if the car is not
used for a longer time or when it is only
driven short distances. Extreme cold further limits starting capacity.
To maintain the battery in good condition,
at least 15 minutes of driving/week is recommended or that the battery is connected to a battery charger with automatic
trickle charging.
Battery - symbols
Avoid sparks and naked
flames.
There are information and warning symbols
on the battery.
Symbols on the battery
10
Use protective goggles.
Risk of explosion.
Further information in the
owner's manual for the
car.
Must be taken for recycling.
A battery that is kept fully charged has a
maximum service life.
Related information
•
•
•
Store the battery out of
the reach of children.
NOTE
Battery - symbols (p. 371)
Starter battery - replacement (p. 372)
An expended battery must be recycled in
an environmentally safe manner as it contains lead.
Battery - Start/Stop (p. 372)
The battery contains corrosive acid.
Related information
•
•
Starter battery - general (p. 369)
Battery - Start/Stop (p. 372)
371
10 Maintenance and service
10
Starter battery - replacement
Battery - Start/Stop
The starter battery should be replaced by an
authorised workshop.
Cars with Start/Stop function, in addition to
the starter battery, are equipped with a support battery.
The starter battery is a traditional 12 V battery.
Volvo recommends that you allow an authorised workshop to replace the batteries - an
authorised Volvo workshop is recommended.
For more information on the car's starter battery, see Jump starting (p. 268).
Cars with the Start/Stop function are equipped with two 12 V batteries - one extra powerful starter battery for starting and one support battery that helps during the Start/Stop
function's starting sequence.
For more information on the Start/Stop function, see Start/Stop* (p. 277).
For more information on the car's starter battery, see Jump starting (p. 268).
The following table shows specifications for
the support battery.
Voltage (V)
Cold start capacityA CCAB (A)
12
13
372
Enhanced Flooded Battery.
Absorbed Glass Mat.
* Option/accessory, for more information, see Introduction.
12
120C
170D
Size , L×W×H (mm)
Capacity (Ah)
A
B
C
D
150×90×106C
150×90×130D
8C
10D
According to EN standard.
Cold Cranking Amperes.
Manual gearbox in combination with Start/Stop function
that only auto-stops when the car is completely stationary.
Others.
IMPORTANT
When replacing the starter battery, in cars
with Start/Stop function, a battery of the
correct type must be fitted, EFB12 in cars
with manual gearbox and AGM13 in cars
with automatic gearbox.
When replacing the support battery, a battery of AGM type must be fitted.
10 Maintenance and service
NOTE
•
•
Location of the batteries
The higher the current take-off in the
car, the more the alternator must be
working and the batteries charging =
Increased fuel consumption.
When the capacity of the starter battery has fallen below the lowest permissible level then the Start/Stop function is disengaged.
The negative battery terminal on the
car's starter battery must never be
used for connecting an external battery or battery charger - only the car
chassis may be used as the grounding point.
See Jump starting (p. 268) for a description of how the cable clamps must be
attached.
•
14
15
The engine starts automatically14 without
the driver depressing the clutch pedal
(manual gearbox).
The engine starts automatically without
the driver lifting his/her foot off the foot
brake pedal (automatic gearbox).
10
•
Temporarily reduced Start/Stop function due
to high current take-off means:
•
IMPORTANT
If the following instruction is not observed
then the Start/Stop function may temporarily cease to work after the connection of
an external battery or battery charger:
(1) Starter battery15 (2) Support battery
The support battery normally requires no
more service than the normal starter battery.
A workshop should be contacted in the event
of questions or problems - an authorised
Volvo workshop is recommended.
Automatic starting can only take place if the gear lever is in neutral position.
See Starter battery - general (p. 369) for a detailed description of the starter battery.
}}
373
10 Maintenance and service
||
NOTE
If the battery has become so discharged
that everything is "black" and in principle
the car does not have all the normal electrical functions and the engine is subsequently started using an external battery or
battery charger, then the Start/Stop function will be activated. It will then be possible for the engine to be auto-stopped but
in the event of an auto-stop the Start/Stop
function may fail to auto-start the engine
due to inadequate capacity in the battery.
10
The battery must first be charged in order
to ensure a successful auto-start after an
auto-stop. At an outside temperature of
+15 °C the battery needs to be charged for
at least 1 hour. At a lower outside temperature a charging time of 3-4 hours is
recommended. The recommendation is
that the battery is charged using an external battery charger.
If this is not possible then the recommendation is to temporarily deactivate the
Start/Stop function until the battery has
been adequately recharged.
For more information on charging the
starter battery, see Starter battery - general (p. 369).
Related information
•
374
Battery - symbols (p. 371)
Electrical system
Fuses - general
The electrical system is single-pole and uses
the chassis and engine casing as a conductor.
All electrical functions and components are
protected by a number of fuses in order to
protect the car's electrical system from damage by short circuiting or overloading.
The car has a voltage-regulated AC alternator.
The size, type and performance of the starter
battery depend on the car's equipment and
function.
IMPORTANT
If the starter battery is replaced, make sure
you replace it with a battery with the same
cold starting capacity and type as the original battery (see the label on the battery).
Related information
•
•
Starter battery - replacement (p. 372)
Starter battery - general (p. 369)
If an electrical component or function does
not work, it may be because the component's
fuse was temporarily overloaded and failed. If
the same fuse fails repeatedly then there is a
fault in the circuit. Volvo recommends that
you visit an authorised Volvo workshop for
checking.
Changing
1. Look in the fuse diagram to locate the
fuse.
2. Pull out the fuse and check from the side
to see whether the curved wire has
blown.
3. If this is the case, replace it with a new
fuse of the same colour and amperage.
WARNING
Never use a foreign object or a fuse with
an amperage higher than that specified
when replacing a fuse. This could cause
significant damage to the electrical system
and possibly lead to fire.
10 Maintenance and service
Location of central electrical units
10
Fuse box locations in a left-hand drive car. In
a right-hand drive car the fuse box under the
glovebox changes sides.
Engine compartment
Under the glovebox
Under the right-hand front seat
Related information
•
•
•
Fuses - in engine compartment (p. 376)
Fuses - under glovebox (p. 380)
Fuses - under the right-hand front seat
(p. 383)
375
10 Maintenance and service
Fuses - in engine compartment
10
Fuses in the engine compartment protect
engine and brake functions, amongst other
things.
On the inside of the cover there are tweezers
that facilitate the procedure for the removal
and fitting of fuses.
The fuse box also provides space for several
spare fuses.
Replacing fuses
The fuses can be accessed following the
removal of the cover fitted on the starter battery and the cover for the electrical distribution unit.
376
Removing the covers
Fold out the locking catches that are
fitted on the sides of the cover on the
starter battery.
Lift the cover straight up.
10 Maintenance and service
Positions
The label on the inside of the cover shows the
positions of the fuses.
•
•
Fuses 7-18 are of "JCASE" type and
should be replaced by a workshop16.
Fuses 19-45 and 47-48 are of "Mini Fuse"
type.
A
Central electronic module, reference voltage, support battery
5
Horn
15
Brake light
5
Function
A
-
-
Fold out the locking catch that is fitted
on the side of the electrical distribution
unit.
ABS pump
40
Headlamp control
5
ABS valves
30
Internal relay coils
5
Rotate the cover upward until the lock
lugs (1) are released.
Headlamp washers*
20
40
12 V socket, tunnel console
front
15
Ventilation fan
Transmission control module
15
30
Solenoid clutch A/C (1.6 litre, 5cyl. petrol)
15
-
12 V socket, tunnel console rear
15
Climate sensor*; air intake
throttle motors
7.5
Primary fuse for fuses 32-36
Electric windscreen, right side*
Fold the cover toward the engine to
access the fuses.
Refitting the covers
Reinstall the parts in reverse order.
16
Function
-
-
40
40
Engine control module (4-cyl.
2.0 l, 5-cyl.)
5
Electric windscreen, left side*
Parking heater*
20
Power seat, right*
20
Windscreen wipers
20
An authorised Volvo workshop is recommended.
10
}}
* Option/accessory, for more information, see Introduction.
377
10 Maintenance and service
||
10
378
Function
A
Function
A
Function
A
Relay coil in cooling fan relay
(4-cyl. 1.6 l, 5-cyl. diesel);
Lambda-sonds (4-cyl. 1.6 l petrol); Mass air flow meter (1.6 l
diesel, 5-cyl. diesel), Bypass
valve, EGR cooling (1.6 l diesel);
Bypass solenoid EGR cooling
(5-cyl. diesel); Regulator valve,
fuel flow (5-cyl. diesel); Regulator valve, fuel pressure (5-cyl.
diesel)
10
10
Valves (1.6 l petrol); Solenoids
(1.6 l petrol); Injectors (5-cyl.
petrol); Lambda-sond (5-cyl.
diesel); Crankcase ventilation
heater (5-cyl. diesel)
10
15
Relay coil in cooling fan relay
(5-cyl. petrol); Lambda-sonds
(5-cyl. petrol)
20
Valve (4-cyl 2.0 l diesel); EVAP
valve (4-cyl. 2.0 l petrol); Crankcase ventilation heater (4 cyl.
2.0 l petrol); Engine control
module (4-cyl. 2.0 l), Mass air
flow sensor (4-cyl. 2.0 l); Thermostat (4-cyl. 2.0 l petrol);
Cooling pump for EGR (4 cyl.
2.0 l diesel); Glow control module (4-cyl. 2.0 l diesel)
15
Lambda sonds (4-cyl. 2.0 l);
Relay coil in relay for cooling
fan (4-cyl. 2.0 l)
Oil pump automatic gearbox
(5-cyl.); Mass air flow sensor
(1.6 l petrol, 5-cyl. petrol); EVAP
valve (1.6 l petrol); Valves (4 cyl.
2.0 l 5-cyl. petrol); Solenoids (5cyl. petrol); Crankcase ventilation heater (5-cyl. petrol); Control motor turbo (1.6 l diesel);
Regulator valve, fuel flow (1.6 l
diesel); Control module radiator
roller cover (1.6 l diesel); Solenoid piston cooling (5-cyl. diesel); Turbo control valve (5-cyl.
diesel); Oil level sensor (5-cyl.
diesel); Compressor A/C (4-cyl.
2.0 l 5-cyl. diesel); Oil pump (4cyl. 2.0 l); Cooling valve for climate control system (4-cyl. 2.0 l
diesel); Relay coils in relays for
Start/Stop functions
Ignition coils (1.6 l petrol, 5-cyl.
petrol)
10
Ignition coils (4-cyl. 2.0 l petrol);
Diesel filter heater (1.6 l diesel,
5-cyl. diesel); Glow control
module (5-cyl. diesel)
15
Diesel filter heater (4-cyl. 2.0 l
diesel)
25
Engine control module (1.6 l)
10
Engine control module (4-cyl.
2.0 l, 5-cyl.); Throttle unit (5-cyl.
petrol)
15
10 Maintenance and service
Function
A
ABS
5
Engine control module; Transmission control module; Airbags
7.5
Light height control*
10
Electric control servo
5
Central electronic module
15
-
-
-
-
Collision warning system
5
Accelerator pedal sensor
5
Charging point, support battery
-
-
-
Coolant pump (when no parking
heater is available)
10
10
Related information
•
•
Fuses - under glovebox (p. 380)
Fuses - under the right-hand front seat
(p. 383)
* Option/accessory, for more information, see Introduction.
379
10 Maintenance and service
Fuses - under glovebox
10
Fuses under the glovebox protect the airbag
and passenger compartment lighting functions, amongst other things.
On the inside of the cover for the fuse box in
the engine compartment there are tweezers
that facilitate the procedure for the removal
and fitting of fuses.
The fuse box in the engine compartment
also provides space for several spare fuses.
Replacing fuses
The fuses can be accessed when a protective
cover has been removed from the fuse box.
380
Cover removal
Take hold of the recess and pull until the
locking lugs in the lower edge of the
cover are released from the fuse box.
Remove the cover.
NOTE
A relatively large amount of tensile force is
required to release the locking lugs at the
top edge of the cover from the electrical
distribution unit.
10 Maintenance and service
Cover refitting
Guide in the lower lugs.
Turn the cover upwards until the upper
lugs engage.
NOTE
Make sure that the upper locking lugs are
seated properly in the grooves of the electrical distribution unit.
Positions
The fuses are of "Mini Fuse" type.
Function
A
Fuel pump
20
Rear window wiper
15
Function
A
Function
Display in roof console (Seatbelt reminder/Indicator for airbag on the front passenger
seat)
5
Climate panel
7.5
Steering wheel module
7.5
Interior lighting, Controls in roof
console for front reading lamps
and passenger compartment
lighting; Power seats*
7.5
Power operated roller blind,
glass roof*
10
Rain sensor*; Dimming, interior
rearview mirror*; Moisture sensor*
5
Collision warning system*
5
-
-
Unlocking, tailgateA
10
A
Siren*; Data link connector
OBDII
5
Main beam
15
-
10
-
Reversing lamp
7.5
Windscreen wipersC; Rear
windscreen wiperC
20
Immobiliser
5
Reserve position 1, constant
voltage
15
Reserve position 2, constant
voltage
20
-
5
Movement sensor alarm*;
Remote receiver
5
Reserve position 3, constant
voltage
15
Windscreen wipersD; Rear
windscreen wiperD
20
Steering lock
Combined instrument panel
5
10
Central locking system, fuel
filler flapB
10
Central locking system, fuel
filler flapE
Unlocking, tailgateF
10
}}
* Option/accessory, for more information, see Introduction.
381
10 Maintenance and service
||
Function
10
A
B
C
D
E
F
A
Electric additional heater*; Button seat heating rear*
7.5
Airbags; Pedestrian airbag*
7.5
Reserve position 4, constant
voltage
7.5
-
-
-
-
See also fuse 84.
See also fuse 83.
See also fuse 82.
See also fuse 77.
See also fuse 70.
See also fuse 65.
Related information
•
•
382
Fuses - in engine compartment (p. 376)
Fuses - under the right-hand front seat
(p. 383)
* Option/accessory, for more information, see Introduction.
10 Maintenance and service
Fuses - under the right-hand front
seat
Fuses under the right-hand front seat protect
the infotainment system and trailer functions,
amongst other things.
On the inside of the cover for the fuse box in
the engine compartment there are tweezers
that facilitate the procedure for the removal
and fitting of fuses.
The fuse box in the engine compartment
also provides space for several spare fuses.
17
10
Positions
•
Fuses 24-28 are of "JCASE" type and
should be replaced by a workshop17.
•
Fuses 1-23 and 29-46 are of "Mini Fuse"
type.
Function
A
-
-
Keyless*
10
Door handle (Keyless*)
5
Control panel, left front door
25
An authorised Volvo workshop is recommended.
}}
* Option/accessory, for more information, see Introduction.
383
10 Maintenance and service
||
10
384
Function
A
Function
A
Function
A
Control panel, right front door
25
-
-
-
-
Control panel, left rear door
25
-
-
-
-
Control panel, right rear door
25
-
-
-
-
Primary fuse for fuses 12-16:
Infotainment
25
Trailer socket 2*
20
Seat heating, rear right*
15
Power seat, left*
20
Audio control unit (amplifier)*
30
Seat heating, rear left*
15
-
-
-
Trailer socket 1*
40
-
-
Rear window defroster
30
-
-
-
-
-
-
-
BLIS*
5
-
-
Telematics*; Bluetooth*
5
Parking assistance*
5
-
-
Audio control module or Control
module SensusA; Infotainment
control module or ScreenA
15
Parking camera*
5
-
-
Digital radio*; TV*
7.5
-
-
12 V socket, cargo area
15
Seat heating, front driver's side
15
Seat heating, front passenger
side
15
-
-
Internal relay coil
5
Audio control unit (amplifier)*,
signal for diagnosis
5
-
-
-
-
-
* Option/accessory, for more information, see Introduction.
-
A
Certain model variants.
Related information
•
•
Fuses - in engine compartment (p. 376)
Fuses - under glovebox (p. 380)
10 Maintenance and service
Car washing
WARNING
The car should be washed as soon as it
becomes dirty. Wash the car in a car wash
with oil separator. Use car shampoo.
Always have the engine cleaned by a
workshop. There is a risk of fire if the
engine is hot.
Do not use any strong solvents.
Washing by hand
•
•
•
•
Dirty headlamps have impaired functionality. Clean them regularly, when refuelling
for example.
Do not use any corrosive cleaning agents
but use water and a non-scratching
sponge instead.
Hose down the underbody.
Rinse the entire car until the dissolved dirt
has been removed so as to reduce the
risk of scratches from washing. Do not
spray directly onto the locks.
NOTE
Outside lighting such as headlamps, fog
lamps and rear lamps may temporarily
have condensation on the inside of the
lens. This is normal, all exterior lighting is
designed to withstand this. Condensation
is normally vented out of the lamp housing
when the lamp has been switched on for a
time.
If necessary, use cold degreasing agent
on very dirty surfaces. Note that in this
case, the surfaces must not be hot from
the sun!
Wash using a sponge, car shampoo and
plenty of lukewarm water.
•
Clean the wiper blades with a lukewarm
soap solution or car shampoo.
•
Dry the car using a clean, soft chamois or
a water scraper. If you avoid allowing
drops of water to dry in strong sunlight,
you reduce the risk of water drying stains
which may need to be polished out.
10
IMPORTANT
Remove bird droppings from the paintwork as soon as possible. Bird droppings
contain chemicals that affect and discolour paintwork very quickly. An authorised
Volvo workshop is recommended for the
removal of any discoloration.
•
NOTE
Wash the wiper blades and windscreen
regularly with lukewarm soap solution or
car shampoo.
Wiper blades
Automatic car washes
An automatic car wash is a simple and quick
way of washing the car, but it cannot reach
everywhere. Handwashing the car is recommended for achieving optimum results.
NOTE
The car must only be washed by hand
over the first few months. This is because
the paint is more delicate when it is new.
High-pressure washing
When using high-pressure washing, use
sweeping movements and make sure that the
nozzle does not come closer than 30 cm to
the surface of the car (the distance applies to
all exterior parts). Do not spray directly onto
the locks.
Asphalt, dust and salt residue on wiper
blades, as well as insects, ice etc. on the
windscreen, impair the service life of wiper
blades.
For cleaning:
–
Set the wiper blades to the service position; see Wiper blades (p. 366).
}}
385
10 Maintenance and service
||
Testing the brakes
IMPORTANT
Avoid waxing and polishing on plastic and
rubber.
WARNING
10
Always test the brakes after washing the
car, including the parking brake, to ensure
that moisture and corrosion do not attack
the brake linings and reduce braking performance.
Lightly depress the brake pedal now and then
when driving long distances in rain or slush.
The heat from the friction causes the brake
linings to warm up and dry. Do the same
thing after starting in very damp or cold
weather.
Exterior plastic, rubber and trim
components
A special cleaning agent available from Volvo
dealers is recommended for the cleaning and
care of coloured plastic parts, rubber and trim
components, such as glossy trim mouldings.
When using such a cleaning agent the
instructions must be followed carefully.
When using degreasant on plastic and
rubber, only rub with light pressure if it is
necessary. Use a soft washing sponge.
Polishing glossy trim mouldings could
wear away or damage the glossy surface
layer.
Polishing agent that contains abrasive
must not be used.
Rims
Only use rim cleaning agent recommended
by Volvo.
Strong rim cleaning agents can damage the
surface and cause stains on chrome-plated
aluminium rims.
Related information
•
•
•
Polishing and waxing (p. 386)
Cleaning the interior (p. 388)
Water and dirt-repellent coating (p. 387)
Polishing and waxing
Polish and wax the car if the paintwork is dull
or to give the paintwork extra protection.
The car does not need to be polished until it
is at least one year old. However, the car can
be waxed during this time. Do not polish or
wax the car in direct sunlight.
Wash and dry the car thoroughly before you
begin polishing or waxing. Clean off asphalt
and tar stains using tar remover or white spirit. More stubborn stains can be removed
using fine rubbing paste designed for car
paintwork.
Polish first with a polish and then wax with
liquid or solid wax. Follow the instructions on
the packaging carefully. Many preparations
contain both polish and wax.
IMPORTANT
Avoid waxing and polishing on plastic and
rubber.
When using degreasant on plastic and
rubber, only rub with light pressure if it is
necessary. Use a soft washing sponge.
Polishing glossy trim mouldings could
wear away or damage the glossy surface
layer.
Polishing agent that contains abrasive
must not be used.
386
10 Maintenance and service
IMPORTANT
Only paint treatment recommended by
Volvo should be used. Other treatment
such as preserving, sealing, protection,
lustre sealing or similar could damage the
paintwork. Paintwork damage caused by
such treatments is not covered by Volvo
warranty.
Related information
•
Car washing (p. 385)
Water and dirt-repellent coating
Rustproofing
The windows are treated with a surface coating that improves visibility in difficult weather
conditions.
The car received a thorough and complete
rustproofing at the factory. Parts of the body
are made of galvanised sheet metal. The
underbody is protected by a wear-resistant
anti-corrosion compound. A thin, penetrating
rustproofing fluid was sprayed into the
exposed members, cavities, closed sections
and side doors.
Water and dirt-repellent coating*
There is natural wear of the waterrepellent coating.
Maintenance:
•
Never use products such as car wax,
degreaser or similar on glass surfaces as
this could ruin their water-repellent properties.
•
Take care when cleaning so as not to
damage the glass surface.
•
To avoid damaging glass surfaces when
removing ice – only use plastic ice scrapers.
•
Treatment with a special finishing agent
available from Volvo dealers is recommended in order to maintain the waterrepellent properties. This should be used
first after three years and then each year.
Inspection and maintenance
Dirt and road salt can lead to corrosion so it
is important to keep the car clean. The car's
rustproofing needs to be checked regularly
and touched-up if necessary in order for it to
be maintained.
Under normal conditions the rustproofing
does not require treatment for approximately
12 years. After this period, it should be treated at three-year intervals. Volvo recommends that you engage an authorised Volvo
workshop for assistance if the car needs further treatment.
Related information
•
IMPORTANT
10
Paint damage (p. 389)
Do not use a metal ice scraper to remove
ice from the windows. Use the heating to
remove ice from the door mirrors; see Windows and rearview and door mirrors heating (p. 102).
Related information
•
Car washing (p. 385)
* Option/accessory, for more information, see Introduction.
387
10 Maintenance and service
Cleaning the interior
10
Only use cleaning agents and car care products recommended by Volvo. Clean regularly
and follow the instructions included with the
car care product.
Vacuuming is important prior to using cleaning agents.
Carpets and cargo area
Remove inlaid carpets for separate cleaning
of the floor carpet and the inlaid carpets. Use
a vacuum cleaner to remove dust and dirt.
Each inlay mat is secured with pins.
–
Take hold of the inlay mat at each pin and
lift the mat straight up.
Fit the inlay mat in place by pressing it in
at each pin.
WARNING
Only use one inlaid mat at each seat, and
check before setting off that the mat by
the driver's seat is firmly affixed and
secured in the pins so that it does not get
caught adjacent to and under the pedals.
A special textile cleaner is recommended for
stains on the floor mat after vacuuming. Floor
mats should be cleaned with agents recommended by your Volvo dealer!
388
Stains on fabric upholstery and roof
upholstery
A special fabric cleaning agent, available from
authorised Volvo dealers, is recommended to
avoid impairing the fire retardant qualities of
the upholstery.
IMPORTANT
Sharp objects and Velcro may damage the
fabric upholstery.
IMPORTANT
•
•
with the instructions, preserves the leather's
protective coating. After a period of use the
natural appearance of the leather will nevertheless emerge, depending more or less on
the surface texture of the leather. This is a
natural maturing of the leather and shows
that it is a natural product.
To achieve best results Volvo recommends
cleaning and the application of protective
cream once to four times per year (or more if
necessary). The Volvo Leather Care kit is
available from your Volvo dealer.
IMPORTANT
Certain items of coloured clothing (for
example, jeans and suede garments)
may stain the upholstery.
•
Never use strong solvents. Such products may damage fabric, vinyl and
leather upholstery.
Certain items of coloured clothing (for
example, jeans and suede garments)
may stain the upholstery.
•
Never use strong solvents. Such products may damage fabric, vinyl and
leather upholstery.
Stains on leather upholstery
Volvo's leather upholstery is treated to preserve its original appearance.
Washing instructions for leather
upholstery
Leather upholstery ages and acquires a beautiful patina over time. The leather is refined
and processed so that it retains its natural
characteristics. It is given a protective coating, but regular cleaning is required in order
to maintain both characteristics and appearance. Volvo offers a comprehensive product
for the cleaning and treatment of leather
upholstery which, when used in accordance
1. Pour the leather cleaner on the dampened sponge and squeeze out a strong
foam.
2. Work the dirt away with gentle circular
movements.
3. Dab accurately with the sponge on the
stains. Allow the sponge to absorb the
stain. Do not rub.
10 Maintenance and service
4. Wipe off with soft paper or a cloth and
allow the leather to dry completely.
Group 2 (fats, oils, sauces and chocolate)
Paint damage
1. Same procedure as for group 1.
Protective treatment of leather
upholstery
2. Polish with an absorbent paper or cloth.
Paint is an important part of the car's rustproofing and should therefore be checked
regularly. The most common types of paintwork damage are stone chips, scratches, and
marks on the edges of wings, doors and
bumpers.
1. Pour a small amount of the protective
cream on the felted cloth and massage in
a thin layer of cream with gentle circular
movements on the leather.
2. Allow the leather to dry for 20 minutes
before use.
The leather has now been given improved
protection against stains and improved UV
protection.
Washing instructions for the leather
steering wheel
•
Remove dirt and dust with a soft premoistened sponge and neutral soap.
•
Leather needs to breathe. Never cover
the leather steering wheel with protective
plastic.
•
1. Use a soft brush to remove the dirt.
2. Same procedure as for group 1.
Group 1 (ink, wine, coffee, milk, sweat and
blood)
Use a soft cloth or sponge. Mix a 5%
ammonia solution. (For blood stains, use
a solution of 2 dl water and 25g salt.)
10
Touching up minor paintwork damage
Stains on interior plastic parts, metal
parts and wood parts
To avoid the onset of rust, damaged paintwork should be rectified immediately.
A fibrillated fibre or microfibre cloth, lightly
moistened with water, available from Volvo
dealers, is recommended for cleaning interior
parts and surfaces.
Materials
Do not scrape or rub stains. Never use strong
stain removers. A special cleaning agent
available from Volvo dealers can be used for
more difficult cleaning.
IMPORTANT
Do not use solvents with high alcohol content, e.g. washer fluid, to clean the combined instrument panel.
Use natural oils. Volvo's leather care
agents are recommended for best results.
If the steering wheel has stains:
–
Group 3 (dry dirt, dust)
Seatbelts
Use water and a synthetic detergent. A special textile cleaning agent is available from
your Volvo dealer. Make sure the seatbelt is
dry before allowing it to retract.
Related information
•
Car washing (p. 385)
}}
389
10 Maintenance and service
||
10
•
primer18 - a special adhesive primer in a
spray can is available for e.g. plasticcoated bumpers
•
basecoat and clearcoat - available in
spray cans or as touch-up pens/sticks19
•
•
masking tape
fine sand
Repair minor paintwork damage such
as stone chips and scratches
2. Before painting, gentle polishing using a
very fine polishing agent may be carried
out locally if required (e.g. if there are any
uneven edges). The surface is cleaned
thoroughly and left to dry.
3. Stir the primer well and apply using a fine
brush, a matchstick or similar. Finish off
with a basecoat and clearcoat once the
primer has dried.
paper18.
G021832
Colour code
4. For scratches, proceed as above, but
mask around the damaged area to protect the undamaged paintwork.
NOTE
Before work is begun, the car must be clean
and dry and at a temperature above 15 °C.
If the stone chip has not penetrated down
to the meal and an undamaged layer of
paint remains in place, fill in with basecoat
and clearcoat as soon as the surface has
been cleaned.
1. Apply a piece of masking tape over the
damaged surface. Then remove the tape
to remove any loose paint.
Exterior colour code
Any secondary exterior colour code
It is important that the correct colour is used.
For product label location, see Type designations (p. 392).
18
19
390
If the damage is down to the metal, use
of a primer is appropriate. In the event of
damage to a plastic surface, an adhesive
primer should be used to give better
results - spray into the lid of the spray
can and brush on thinly.
If required.
Follow the instructions that are included with the package for the touch-up pen/stick.
Related information
•
Rustproofing (p. 387)
SPECIFICATIONS
11 Specifications
Type designations
Label location
11
392
Type designation, vehicle identification number, etc., i.e. information unique to the car,
can be read on a label in the car.
11 Specifications
Knowing the car's type designation, vehicle
identification and engine numbers can facilitate all contact with an authorised Volvo
dealer regarding the car and when ordering
spare parts and accessories.
Type designation, vehicle identification
number, permissible maximum weights
and code designation for exterior colour
and type approval number. The label is
visible when the right rear door is opened.
Label for A/C system.
Label for parking heater.
NOTE
It is not intended that the decals illustrated
in the owner's manual should be exact
replicas of those in the car. They are
included to show their approximate
appearance and location in the car. The
information that applies to your particular
car is available on the respective decals
for your car.
11
Related information
•
•
Weights (p. 395)
Engine specifications (p. 398)
Engine code and engine serial number.
Label for engine oil.
Gearbox type designation and serial number.
Manual gearbox
Automatic gearbox
Car's identification number. (VIN Vehicle
Identification Number)
Further information on the car is presented in
the registration document.
393
11 Specifications
Dimensions
Measurement of car length, height, etc. can
be read in the table.
11
V40.
Dimensions
mm
A
Wheelbase
2647
B
Length
4369
C
394
Load length, floor, folded rear
seat
D
Load length, floor
E
Height
F
Load height
1508
G
H
Dimensions
mm
Front track
1546A
Rear track
Dimensions
mm
J
Width
1802
1551B
K
Width including door mirrors
2041
1559C
L
Width including folded-in
door mirrors
1857
1533A
684
1538B
1420
1546C
532
I
Load width, floor
960
A
B
C
Offset 52.5 mm.
Offset 50 mm.
Offset 46 mm.
11 Specifications
Weights
WARNING
Max. gross vehicle weight, etc. can be read
on a label in the car.
The car's driving characteristics change
depending on how heavily it is loaded and
how the load is distributed.
Kerb weight includes the driver, the fuel tank
90% full and all fluids.
The weight of passengers and accessories,
and towball load (p. 396) (when a trailer is
hitched) influence the load capacity and are
not included in the kerb weight.
11
Permitted max. load = Gross vehicle weight Kerb weight.
NOTE
The documented kerb weight applies to
cars in the standard version - i.e. a car
without extra equipment or accessories.
This means that for every accessory added
the loading capacity of the car is reduced
correspondingly by the weight of the
accessory.
Examples of accessories that reduce loading capacity are the Kinetic/Momentum/
Summum equipment levels, as well as
other accessories such as Towbar, Load
carrier, Space box, Audio system, Auxiliary
lamps, GPS, Fuel-driven engine block
heater, Safety grille, Carpets, Cargo cover,
Power seats, etc.
Weighing the car is a certain way of ascertaining the kerb weight of your own particular car.
For information on label location, see Type designations (p. 392).
Max. gross vehicle weight
Max. train weight (car+trailer)
Max. front axle load
Max. rear axle load
Equipment level
Max. load: See registration document.
Max. roof load: 75 kg.
Related information
•
Towing capacity and towball load
(p. 396)
395
11 Specifications
Towing capacity and towball load
Towing capacity and towball load for driving
with a trailer can be read in the tables.
Max. weight braked trailer
V40
Engine codeA
Gearbox
Max. weight braked trailer (kg)
Max. towball load (kg)
T2
B4164T4
Manual, B6
1300
75
T3
B4164T3
Manual, B6
1300
75
T4
B4164T
Manual, B6
1300
75
T4
B4164T
Automatic, MPS6
1500
75
T4
B5204T8
Automatic, TF-80SD
1500
75
T5
B5204T9
Automatic, TF-80SD
1500
75
T5
B4204T11
Automatic, TG-81SC
1500
75
D2
D4162T
Manual, B6
1300
75
D2
D4162T
Automatic, MPS6
1300
75
D3
D5204T6
Manual, M66
1500
75
D3
D5204T6
Automatic, TF-80SD
1500
75
D4
D4204T14
Manual, M66
1500
75
D4
D4204T14
Automatic, TG-81SC
1500
75
Engine
11
A
396
Engine code, component and serial number can be read on the engine; see Type designations (p. 392).
11 Specifications
Max. weight unbraked trailer
V40
Engine codeA
Gearbox
Max. weight unbraked trailer (kg)
Max. towball load (kg)
T2
B4164T4
Manual, B6
650
50
T3
B4164T3
Manual, B6
650
50
T4
B4164T
Manual, B6
650
50
T4
B4164T
Automatic, MPS6
700
50
T4
B5204T8
Automatic, TF-80SD
700
50
T5
B5204T9
Automatic, TF-80SD
700
50
T5
B4204T11
Automatic, TG-81SC
700
50
D2
D4162T
Manual, B6
650
50
D2
D4162T
Automatic, MPS6
700
50
D3
D5204T6
Manual, M66
700
50
D3
D5204T6
Automatic, TF-80SD
750
50
D4
D4204T14
Manual, M66
700
50
D4
D4204T14
Automatic, TG-81SC
700
50
Engine
A
11
Engine code, component and serial number can be read on the engine; see Type designations (p. 392).
Related information
•
•
•
Weights (p. 395)
Driving with a trailer (p. 300)
Trailer Stability Assist - TSA (p. 307)
397
11 Specifications
Engine specifications
Engine specifications (output etc.) for each
respective engine alternative can be read in
the table.
V40
11
Engine
Engine
codeA
Output
(kW/rpm)
Output
(hp/rpm)
Torque (Nm/
rpm)
No. of
cylinders
Bore
(mm)
Stroke
(mm)
Swept
volume
(litres)
Compression
ratio
T2
B4164T4
88/4500
120/4500
240/1600-3000
4
79
81.4
1.596
10.0:1
T3
B4164T3
110/5700
150/5700
240/1600–4000
4
79
81.4
1.596
10.0:1
T4
B4164T
132/5700
180/5700
240/1600–5000
4
79
81.4
1.596
10.0:1
T4
B5204T8
132/5000
180/5000
300/2700–4000
5
81.0
77
1.984
10.5:1
T5
B5204T9
157/6000
213/6000
300/2700–5000
5
81.0
77
1.984
10.5:1
T5
B4204T11
180/5500
245/5500
350/1500–4800
4
82
93.2
1,969
10.8:1
D2
D4162T
84/3600
115/3600
270/1750-2500
4
75
88.3
1.560
16.0:1
D3
D5204T6
110/3500
150/3500
350/1500-2750
5
81.0
77
1.984
16.5:1
D4
D4204T14
140/4250
190/4250
400/1750-2500
4
82.0
93.2
1,969
15.8:1
A
Engine code, component and serial number can be read on the engine; see Type designations (p. 392).
Related information
•
•
398
NOTE
Not all engines are available in all markets.
Coolant - grade and volume (p. 402)
Engine oil - grade and volume (p. 400)
11 Specifications
Engine oil - adverse driving conditions
Related information
•
•
Adverse driving conditions can lead to abnormally high oil temperature or oil consumption.
Below are some examples of adverse driving
conditions.
Engine oil - grade and volume (p. 400)
Engine oil - general (p. 353)
Check the oil level (p. 354), more frequently
for long journeys:
•
•
•
•
towing a caravan or trailer
11
in mountainous regions
at high speeds
in temperatures colder than -30 °C or
hotter than +40 °C
The above also apply to shorter driving distances at low temperatures.
Choose a fully synthetic engine oil for adverse
driving conditions. It provides extra protection
for the engine.
Volvo recommends:
IMPORTANT
In order to fulfil the requirements for the
engine's service intervals all engines are
filled with a specially adapted synthetic
engine oil at the factory. The choice of oil
has been made very carefully with regard
to service life, starting characteristics, fuel
consumption and environmental impact.
An approved engine oil must be used in
order that the recommended service intervals can be applied. Only use a prescribed
grade of oil for both filling and oil change,
otherwise you will risk affecting service life,
starting characteristics, fuel consumption
and environmental impact.
Volvo Car Corporation disclaims all warranty liability if engine oil of the prescribed
grade and viscosity is not used.
Volvo recommends that oil changes are
carried out at an authorised Volvo workshop.
399
11 Specifications
Engine oil - grade and volume
Recommended engine oil grade and volume
for each respective engine alternative can be
read in the table.
Volvo recommends:
11
V40
Engine codeA
Oil grade
Engine
T2
T3
400
Volume, incl. oil filter
(litres)
B4164T4
Certified and factory-filled oil: Oil grade WSS-M2C925-A
approx. 4.1
B4164T3
options for service:
approx. 4.1
Oil grade: ACEA A5/B5
T4
B4164T
D2
D4162T
D3
D5204T6
T4
B5204T8
Oil grade: ACEA A5/B5
approx 5.5
T5
B5204T9
Viscosity: SAE 0W–30
approx 5.5
Viscosity: SAE 5W–30
Oil grade: ACEA A5/B5
Viscosity: SAE 0W–30
Oil grade: ACEA A5/B5
Viscosity: SAE 0W–30
approx. 4.1
approx. 3.8
approx. 5.9
11 Specifications
V40
Engine codeA
Oil grade
Engine
A
Volume, incl. oil filter
(litres)
T5
B4204T11
D4
D4204T14
Castrol Edge Professional V 0W-20 or VCC RBS0-2AE 0w20
approx. 5.4
approx 5.2
Engine code, component and serial number can be read on the engine; see Type designations (p. 392).
Related information
•
Engine oil - adverse driving conditions
(p. 399)
•
Engine oil - checking and filling (p. 354)
11
401
11 Specifications
Coolant - grade and volume
Approved coolant volume for each respective
engine alternative can be read in the table.
Prescribed grade: Coolant recommended by
Volvo mixed with 50% water2, see the packaging.
V40
11
Volume
EngineA
(litres)
T2
B4164T4
T3
B4164T3
T4
B4164T
D2
D4162T
10.0
D3
D5204T6
8.0
T4
B5204T8
T5
B5204T9
T5
B4204T11
7,5 (7,8B)
D4
D4204T14
8,0 (8,4B)
7.0
8.0
Engine code, component and serial number can be read
on the engine; see Type designations (p. 392).
Applies to cars with fuel-driven heater.
A
B
Related information
•
2
402
Coolant - level (p. 357)
Water quality must fulfil the standard STD 1285.1.
11 Specifications
Transmission fluid - grade and volume
The prescribed transmission fluid and volume
for each respective gearbox alternative can be
read in the table.
Manual gearbox
Manual gearbox
Volume (litres)
B6
approx 1.6
M66
A
approx. 1.9 (approx. 1.45A)
Prescribed transmission fluid
BOT 350M3
11
Applies to the D4204T14 engine.
Automatic gearbox
Automatic gearbox
Volume (litres)
TF-80SD
approx 7.0
TG-81SC
approx. 6.6A
approx. 7.5B
MPS6
A
B
approx 7.3
Prescribed transmission fluid
AW1
AW1
BOT 341
Petrol engines
Diesel engines
NOTE
For the MPS6, oil changes must take place
within certain service intervals.
For other gearboxes the gearbox oil does
not need to be changed under normal driving conditions. However, it may be necessary under adverse driving conditions.
Related information
•
Engine oil - adverse driving conditions
(p. 399)
•
Type designations (p. 392)
403
11 Specifications
Brake fluid - grade and volume
Washer fluid - quality and volume
The medium in a hydraulic brake system is
called brake fluid, and it is used to transfer
pressure from e.g. a brake pedal via a master
brake cylinder to one or more slave cylinders,
which in turn act on a mechanical brake.
Washer fluid is used, together with windscreen and rear window wipers, to keep the
car's windows and headlamps clean and
ensure visibility while driving.
Prescribed grade: DOT 4
11
Volume: 0.6 litres
Related information
•
Brake and clutch fluid - level (p. 358)
Prescribed grade: Washer fluid recommended by Volvo - with frost protection during cold weather and below freezing point.
Volume:
•
•
Cars with headlamp washing: 5.5 litres.
Cars without headlamp washing: 3.2
litres.
Related information
•
•
•
404
Washer fluid - filling (p. 369)
Wiper blades (p. 366)
Wipers and washing (p. 97)
11 Specifications
Fuel tank - volume
Fuel tank volume for each respective engine
alternative can be read in the table.
V40
Volume (litres)
Prescribed grade
Engine
4-cylinder petrol
approx. 62
Petrol: Fuel - petrol (p. 296)
11
5-cylinder petrol
4-cylinder diesel
approx. 52
5-cylinder diesel
approx. 60
Diesel: Fuel - diesel (p. 297)
Related information
•
•
Filling up with fuel (p. 295)
Engine specifications (p. 398)
405
11 Specifications
Air conditioning, fluid - volume and
grade
The prescribed grade and volume of fluids in
the air conditioning system can be read in the
table.
Compressor oil
V40
11
Volume
Prescribed grade
Engine
A
406
Engine codeA
T2
B4164T4
T3
B4164T3
150 ml
T4
B4164T
D2
D4162T
110 ml
T5
B4204T11
60 ml
D4
D4204T14
T4
B5204T8
T5
B5204T9
D3
D5204T6
110 ml
Engine code, component and serial number can be read on the engine; see Type designations (p. 392).
PAG oil
11 Specifications
Coolant
V40
Engine codeA
Weight
Prescribed grade
Engine
T5
B4204T11
D4
D4204T14
Other engines
A
625 g
650 g
Engine code, component and serial number can be read on the engine; see Type designations (p. 392).
R134a
11
WARNING
The air conditioning system contains pressurised refrigerant R134a. This system
must only be serviced and repaired by an
authorised workshop.
Related information
•
Climate control system - fault tracing and
repair (p. 359)
407
11 Specifications
Fuel consumption and CO2 emissions
NOTE
urban driving
Fuel consumption in a vehicle is measured in
litres per 100 km and CO2 emissions in grams
per km.
extra-urban driving
Explanation
combined driving
If the consumption and emission data is
missing then it is included in the enclosed
supplement.
gram/km
11
litre/100 km
V40
408
T2 (B4164T4)
158
6.8
105
4.5
124
5.3
T3 (B4164T3)
158
6.8
105
4.5
124
5.3
T4 (B4164T)
164
7.0
109
4.7
129
5.5
T4A (B4164T)
191
8.2
117
5.0
144
6.2
T4 (B4164T)
184
7.9
120
5.1
143
6.1
T4A (B4164T)
192
8.3
125
5.4
149
6.4
11 Specifications
V40
T4 (B5204T8)
243
10.4
135
5.8
174
7.5
T5 (B5204T9)
243
10.4
135
5.8
174
7.5
T5 (B4204T11)
-
-
-
-
-
-
D2B (D4162T)
100
3.8
82
3,1
88
3.4
D2C (D4162T)
107
4.1
90
3.4
96
3.7
D2B (D4162T)
115
4.4
95
3.6
102
3.9
D2C (D4162T)
116
4.4
99
3.8
105
4.0
D3 (D5204T6)
139
5.3
100
3.8
114
4.3
D3A (D5204T6)
165
6.3
108
4.1
129
4.9
D3 (D5204T6)
179
6.9
112
4.3
136
5.2
D3A (D5204T6)
179
6.8
122
4.6
143
5.4
11
}}
409
11 Specifications
||
V40
11
A
B
C
D
D4C (D4204T14)
-
-
-
-
-
-
D4B (D4204T14)
-
-
-
-
-
-
D4D (D4204T14)
-
-
-
-
-
-
D4C (D4204T14)
-
-
-
-
-
-
D4B (D4204T14)
-
-
-
-
-
-
Only applies to cars equipped with 19-inch wheels.
This only applies to the low-emissions variant.
Does not apply to the low-emission variant.
Only applies to the low-emissions variant (85 g/km CO2).
Fuel consumption and emission values in the
table above are based on specific EU cycles3,
that apply to cars with kerb weight in the
basic version and without extra equipment.
The car's weight may increase depending on
equipment. This, as well as how heavily the
3
410
car is loaded, increases fuel consumption and
carbon dioxide emissions.
There are several reasons for increased fuel
consumption compared with the table's values. Examples of this are:
•
•
The driver's driving style.
If the customer has specified wheels
larger than those fitted as standard on the
model's basic version, then resistance
increases.
Official fuel consumption figures are based on two standardised driving cycles in a laboratory environment ("EU driving cycles") all in accordance with EU Regulation no 692/2008 and 715/2007
(Euro 5 / Euro 6) and UN ECE Regulation no 101. The regulations cover the driving cycles for urban driving and extra-urban driving. - Urban driving - the measurement starts with cold starting the
engine. The driving is simulated. - Extra-urban driving - the car is accelerated and braked at speeds between 0-120 km/h. The driving is simulated. - Cars with manual gearbox are started in 2nd
gear (applies to cars with up to 18-inch wheels). The value for combined driving, which is reported in the table, is a combination of urban driving and extra-urban driving, in accordance with legal
requirements. CO2 emissions - the exhaust gases are collected in order to calculate the carbon dioxide emissions during the two driving cycles. These are then analysed and give the value for
CO2 emissions.
11 Specifications
•
High speed results in increased wind
resistance.
•
Fuel quality, road and traffic conditions,
weather and the condition of the car.
•
Weights (p. 395)
Even a combination of the above-mentioned
examples can result in significantly improved
consumption. For further information, please
refer to the regulations referred to3.
Large deviations in fuel consumption may
arise in a comparison with the EU driving
cycles3 which are used in the certification of
the car and on which the consumption figures
in the table are based.
11
Consumption is higher and power output
lower for fuel with an octane rating of
91 RON.
NOTE
Extreme weather conditions, driving with a
trailer or driving at high altitudes in combination with fuel grade are factors that
could affect the car's performance.
Related information
•
•
•
3
Economical driving (p. 300)
Fuel - petrol (p. 296)
Fuel - diesel (p. 297)
Official fuel consumption figures are based on two standardised driving cycles in a laboratory environment ("EU driving cycles") all in accordance with EU Regulation no 692/2008 and 715/2007
(Euro 5 / Euro 6) and UN ECE Regulation no 101. The regulations cover the driving cycles for urban driving and extra-urban driving. - Urban driving - the measurement starts with cold starting the
engine. The driving is simulated. - Extra-urban driving - the car is accelerated and braked at speeds between 0-120 km/h. The driving is simulated. - Cars with manual gearbox are started in 2nd
gear (applies to cars with up to 18-inch wheels). The value for combined driving, which is reported in the table, is a combination of urban driving and extra-urban driving, in accordance with legal
requirements. CO2 emissions - the exhaust gases are collected in order to calculate the carbon dioxide emissions during the two driving cycles. These are then analysed and give the value for
CO2 emissions.
411
11 Specifications
Tyres - approved tyre pressures
Approved tyre pressures for each respective
engine alternative can be read in the table.
V40
Tyre size
Engine
11
195/65 R15
T2 (B4164T4)
205/55 R16
T3 (B4164T3)
205/50 R17
T4 (B4164T)
225/45 R17
D2 (D4162T)
225/40 R18
Speed
Load, 1 - 3 persons
Max. load
(km/h)
Front
Rear
Front
Rear
Front/rear
(kPa)B
(kPa)
(kPa)
(kPa)
(kPa)
0 - 160
230
230
260
260
260 (270C, 280D)
160 +
230
230
270
270
-
0 - 160
230
230
260
260
260
160 +
290
240
310
270
-
ECO pressureA
235/35 R19
T4 (B5204T8)
205/55 R16
T5 (B5204T9)
205/50 R17
T5 (B4204T11)
225/45 R17
D3 (D5204T6)
225/40 R18
0 - 160
240
240
260
260
260
D4 (D4204T14)
235/35 R19
160 +
290
240
310
280
-
max. 80
420
420
420
420
-
Temporary Spare Tyre
A
B
C
D
412
Economical driving.
In certain countries there is the "bar" unit beside the SI unit "Pascal": 1 bar = 100 kPa.
Only applies to 16" wheels for D2 automatic, low-emission variant.
Only applies to 15" wheels for D2, low-emission variant.
11 Specifications
NOTE
All engines, tyres or combinations of these
are not always available in all markets.
Related information
•
•
•
Tyres - dimensions (p. 316)
Tyres - air pressure (p. 322)
Type designations (p. 392)
11
413
12 Alphabetical Index
A
ACC – Adaptive cruise control................. 198
Active Bending Lights (ABL)...................... 89
Active high beam....................................... 87
Active Park Assist....................................
function...............................................
Limitations..........................................
operation.............................................
Symbols and messages.....................
12
249
250
252
250
253
Alcolock................................................... 261
Airbag
activating/deactivating, PACOS........... 33
driver's side.................................... 31, 39
passenger side......................... 31, 33, 39
Allergy and asthma inducing substances. 123
AIRBAG ..................................................... 31
Airbag system............................................ 30
warning symbol.................................... 29
Approach lighting.............................. 93, 160
Automatic car washes............................. 385
Automatic gearbox.......................... 270, 274
manual gear positions (Geartronic)..... 271
towing and recovery........................... 308
trailer................................................... 302
Automatic relocking................................. 171
Active Xenon headlamps........................... 89
Air cleaning
material............................................... 124
passenger compartment.... 122, 123, 124
Active Yaw Control.................................. 183
Air conditioning........................................ 131
Adapting driving characteristics.............. 259
Air conditioning, fluid
volume and grade............................... 406
B
Adaptive Cruise Control...........................
change cruise control functionality.....
deactivate...........................................
fault tracing.........................................
function...............................................
managing speed.................................
overtaking...........................................
overview..............................................
radar sensor........................................
setting the time interval......................
standby mode.....................................
temporary deactivation.......................
198
207
205
210
199
202
204
201
208
203
203
203
Additional heater
electric........................................ 140, 141
fuel-driven........................................... 140
414
Adjusting the steering wheel...................... 82
Air conditioning system
repair................................................... 359
Air distribution.......................................... 125
Recirculation....................................... 133
table.................................................... 134
Air quality system IAQS........................... 124
Alarm........................................ 178, 179, 180
alarm indicator.................................... 179
alarm signals....................................... 180
automatic activation........................... 179
automatic re-arming........................... 179
checking the alarm............................. 162
reduced alarm level............................ 180
remote control key not working.......... 180
Backrest..................................................... 78
front seat, lowering............................... 78
Backrest rear seat, lowering...................... 80
Bag holder .............................................. 150
folding................................................. 150
Battery............................................. 293, 369
jump starting....................................... 268
maintenance....................................... 369
overload.............................................. 293
remote control key/PCC..................... 165
symbols on the battery....................... 371
warning symbols................................. 371
BLIS................................................. 254, 255
Bonnet, opening...................................... 351
12 Alphabetical Index
Brake fluid
grade and volume............................... 404
Car key memory...................................... 157
rims..................................................... 386
seatbelts............................................. 389
upholstery........................................... 388
Car upholstery......................................... 388
Clean Zone Interior Package (CZIP)........ 123
Brake light.................................................. 90
Car washing............................................. 385
Brakes.............................................. 288, 289
Anti-lock braking system, ABS........... 289
brake light............................................. 90
brake system.............................. 288, 289
Emergency Brake Assistance, EBA ... 290
emergency brake lights........................ 90
filling brake fluid.................................. 359
handbrake........................................... 290
symbols in the combined instrument
panel................................................... 288
Catalytic converter................................... 298
Recovery............................................. 309
Climate control
actual temperature.............................
auto-regulation...................................
general................................................
personal preferences..........................
sensors...............................................
temperature control............................
Book service and repair........................... 346
Brake and clutch fluid.............................. 358
Bulbs, see Lighting.................................. 361
C
Camera sensor................................ 218, 230
Car care................................................... 385
Car care, leather upholstery.................... 388
Cargo area
cargo net............................................. 152
lighting.................................................. 92
loading................................................ 148
mounting points.................................. 150
parcel shelf......................................... 154
Changing wheels..................................... 318
Checking the engine oil level................... 353
Children
child safety locks.................................. 44
child seat and airbag............................ 49
child seats and side airbags................. 36
location in car....................................... 49
safety.............................................. 36, 44
Child safety locks............................ 176, 177
Child seats.................................................
ISOFIX fixture system for child seats...
recommended......................................
size classes for child seats with ISOFIX fixture system.................................
types.....................................................
upper mounting points for child seats..
44
50
45
50
51
53
122
130
121
124
122
131
Clock, adjustment...................................... 70
12
CO2 emissions......................................... 408
Collision..................................................... 40
Collision warning............................. 223, 224
Collision warning system
function............................................... 224
general limitations............................... 229
operation............................................. 227
Pedestrian detection........................... 226
Radar sensor.............................. 208, 216
Collision Warning System with Auto
Brake....................................................... 223
City Safety™............................................ 216
Colour code, paint................................... 390
Cleaning
automatic car wash............................ 385
car washing........................................ 385
Combined instrument panel................ 61, 62
Compass................................................. 104
calibration........................................... 104
415
12 Alphabetical Index
Condensation in headlamps.................... 385
Controls, lights........................................... 83
Control symbols................................... 62, 64
Coolant
volume and grade............................... 402
12
Diesel....................................................... 297
run out of fuel..................................... 297
Diesel particle filter.................................. 299
Driving with a trailer
towball load........................................ 396
towing capacity.................................. 396
E
Coolant, checking and filling................... 357
Dimensions.............................................. 394
Cooling system........................................ 292
overheating......................................... 292
Dipstick, electronic.......................... 354, 356
ECC, electronic climate control............... 127
Direction indicator..................................... 91
Eco Cruise............................................... 286
Corner Traction Control........................... 183
Direction indicators.................................... 91
EcoGuide................................................... 65
Crash, see Collision................................... 40
direction of rotation................................. 312
Ecolabelling, FSC, owner's manual........... 23
Cruise control..........................................
deactivate...........................................
managing speed.................................
resume set speed...............................
temporary deactivation.......................
Disengaging the gear selector inhibitor... 276
Economical driving.................................. 300
Display lighting.......................................... 84
ECO pressure.................................. 322, 412
Distance Warning.................................... 213
Limitations.......................................... 214
Symbols and messages..................... 215
Electrical socket...................................... 147
cargo area........................................... 151
Door mirrors............................................. 101
Electronic climate control - ECC............. 127
Driveable punctured tyres........................ 328
Electronic temperature control - ETC...... 128
Driver Alert Control.................................. 232
operation............................................. 233
Emergency equipment
first aid kit........................................... 324
warning triangle.................................. 323
193
197
194
196
195
CTA.......................................................... 256
Cyclist detection...................................... 225
CZIP (Clear Zone Interior Package)......... 123
D
Daytime running lights............................... 85
Deadlock.................................................. 175
deactivation........................................ 175
temporary deactivation....................... 175
Defroster.................................................. 132
416
Detachable towbar
storage................................................ 303
Driver Alert System.................................. 232
Driving......................................................
cooling system....................................
with a tailer.........................................
with the tailgate open.........................
293
292
300
292
Driving in water........................................ 291
Electrical system...................................... 374
Emergency puncture repair............. 331, 332
action.................................................. 334
inflating the tyres................................ 336
rechecking.......................................... 335
stowing components.......................... 337
12 Alphabetical Index
Emergency puncture repair kit
location............................................... 332
overview.............................................. 333
sealing fluid......................................... 338
Emissions of carbon dioxide................... 408
Engine
deactivate...........................................
overheating.........................................
start.....................................................
Start/Stop...........................................
Error messages
Adaptive Cruise Control.....................
Driver Alert Control.............................
LKA.....................................................
see Messages and symbols...............
211
234
240
211
Error messages in BLIS........................... 258
267
300
266
277
Engine and passenger compartment heater
messages........................................... 139
timer.................................................... 138
Engine block heater................................. 136
Engine block heater and passenger compartment heater
direct start.......................................... 137
immediate stop................................... 138
Engine compartment
coolant................................................ 357
oil........................................................ 353
overview.............................................. 351
Engine drag control................................. 183
Engine oil......................................... 353, 399
adverse driving conditions.................. 399
filter..................................................... 353
grade and volume............................... 400
Engine specifications............................... 398
ETC, electronic temperature control........ 128
External dimensions................................ 394
F
Fuel.......................................... 295, 296, 297
fuel consumption................................ 408
fuel economy...................................... 322
fuel filter.............................................. 297
Fuel-driven heater
timer.................................................... 138
Fuelling............................................ 175, 299
filling................................................... 295
filling with reserve fuel can................. 299
fuel filler flap....................................... 294
fuel filler flap, locking.......................... 175
fuel filler flap, manual opening............ 294
Fan
ECC.................................................... 130
ETC..................................................... 130
Fuel tank
volume................................................ 405
Fault tracing for the camera sensor......... 219
Fuses.......................................................
changing.............................................
engine compartment..........................
General...............................................
under glovebox...................................
under the right-hand front seat...........
First aid.................................................... 324
First aid kit............................................... 324
Fluids, capacities..... 402, 403, 404, 405, 406
Fluids and oils.................. 402, 403, 404, 406
12
Fuse box.................................................. 375
374
374
376
374
380
383
Fog lamp
rear........................................................ 89
Foot brake....................................... 288, 289
Front seat
head restraint........................................ 78
FSC, ecolabelling....................................... 23
G
Gearbox................................................... 269
automatic.................................... 270, 274
manual................................................ 269
Gear selector inhibitor............................. 276
417
12 Alphabetical Index
Gear selector inhibitor, mechanical disengagement................................................. 276
Gear shift indicator.................................. 270
Geartronic................................................ 271
Glass
laminated/reinforced............................. 23
Glass roof, power operated roller blind... 103
Glovebox................................................. 146
cooling................................................ 146
locking................................................ 173
12
Gross vehicle weight............................... 395
GSI - Gear selector assistance................ 270
head restraint
centre seat, rear.................................... 80
front seat............................................... 78
lowering................................................ 80
Instrument overview
left-hand drive car................................ 55
right-hand drive car.............................. 58
Heating
rearview and door mirrors..................
rear window........................................
seats...................................................
windscreen.........................................
Interior Air Quality System (IAQS)
Air cleaning......................................... 124
102
102
129
102
Heat-reflecting windscreen........................ 19
High engine temperature......................... 300
High-pressure headlamp washing............. 98
Hill Start Assist........................................ 277
Instruments and controls..................... 55, 58
Interior lighting, see Lighting..................... 92
Interior rearview mirror............................. 103
automatic dimming............................. 103
Intermittent wiping..................................... 97
Internet-connected car
book service and repair...................... 346
Home safe light duration........................... 93
H
Horn........................................................... 82
Jack......................................................... 315
Handbrake............................................... 290
Hazard warning flashers............................ 90
Headlamp control...................................... 83
Headlamp levelling.................................... 84
Headlamp pattern, adjusting..................... 94
Headlamp pattern adjustment................... 94
Active Bending Lights .......................... 94
Halogen headlamp............................... 94
Headlamps............................................... 361
I
IAQS - Interior Air Quality System........... 124
Journey statistics..................................... 119
Jump starting........................................... 268
Immobiliser.............................................. 159
Indicator symbols...................................... 66
Inflatable curtain.................................. 36, 39
Information button, PCC.......................... 162
Information display.............................. 61, 62
Inlaid mats............................................... 147
Instrument lighting, see Lighting................ 84
418
J
K
Kerb weight.............................................. 395
Key................................................... 156, 158
Key blade......................................... 163, 164
Keyless drive.... 166, 167, 168, 169, 170, 266
12 Alphabetical Index
Keyless - locking..................................... 168
Keyless start (keyless drive)..... 166, 167,
168, 169, 170, 266
Keyless - unlocking................................. 168
Keypad in the steering wheel.................... 82
Key positions............................................. 75
L
Labels...................................................... 392
Laminated glass......................................... 23
Lamps, see Lighting................................ 359
Lane keeping assistant
operation............................................. 238
Lane keeping assistant - LKA.................. 236
Laser sensor............................................ 220
Leather upholstery, washing instructions 388
Light indications, PCC............................. 162
Lighting.................................................... 359
Active Xenon headlamps...................... 89
approach lighting.......................... 93, 160
automatic lighting, passenger compartment............................................... 92
bulbs, specifications........................... 366
controls................................................. 92
daytime running lights.......................... 85
display lighting......................................
headlamp levelling................................
home safe lighting................................
instrument lighting................................
in the passenger compartment.............
main/dipped beam...............................
position/parking lamps.........................
rear fog lamp........................................
tunnel detection....................................
84
84
93
84
92
86
85
89
86
Lighting, bulb replacement...................... 361
daytime running lights........................ 363
dipped beam (cars with halogen headlamps)................................................. 362
direction indicators, front.................... 363
main beam (cars with active xenon
headlamps)......................................... 362
main beam (cars with halogen headlamps)................................................. 362
position/parking lamps....................... 363
rear bulb holder: direction indicators,
brake lamps and reversing lamps...... 364
rear fog lamps..................................... 365
vanity mirror........................................ 365
LKA - Lane keeping assistant.................. 236
Loading
cargo area................................... 148, 150
General....................................... 148, 150
long load............................................. 149
mounting points.................................. 150
roof load............................................. 149
Lock
locking................................................ 170
manual locking.................................... 171
unlocking.................................... 170, 172
Lockable wheel bolts............................... 314
Lock confirmation ................................... 158
Lock indicator.......................................... 158
Locking/unlocking
inside.................................................. 172
tailgate................................................ 173
12
M
Main/dipped beam, see Lighting............... 86
Main beam, automatic activation.............. 87
maintenance
Rustproofing....................................... 387
Manual gearbox.......................................
GSI - Gear selector assistance...........
Towing and recovery..........................
trailer...................................................
269
270
308
302
Manual gear positions (Geartronic).......... 271
Max. roof load.......................................... 395
Memory function in seat............................ 79
419
12 Alphabetical Index
12
Parking brake........................................... 290
Menus
Combined instrument panel............... 105
menu overview, analogue................... 106
menu overview, digital........................ 106
O
Messages................................................ 107
Information display............................. 106
Output...................................................... 398
Messages and symbols
Adaptive Cruise Control..................... 211
Collision Warning with Auto
Brake.......................................... 222, 231
Driver Alert Control............................. 234
Engine block heater and passenger
compartment heater........................... 139
LKA..................................................... 240
Messages in BLIS.................................... 258
Meters
fuel gauge....................................... 61, 62
speedometer................................... 61, 62
tachometer..................................... 61, 62
misting
attending to the windows................... 121
Misting
condensation in headlamps............... 385
Mood lighting............................................. 93
MY CAR................................................... 108
Oil, see also Engine oil..................... 399, 400
Oil level low.............................................. 353
outside temperature gauge....................... 70
Overheating............................................. 300
Owner's manual, ecolabelling.................... 23
Passenger compartment heater.............. 136
Passenger compartment lighting
automatic.............................................. 92
PCC – Personal Car Communicator
functions............................................. 160
range................................................... 163
Pedestrian airbag....................................... 42
folding up.............................................. 43
moving the car...................................... 43
P
PACOS....................................................... 33
Paintwork
colour code......................................... 390
damage and touch-up........................ 389
Pedestrian detection................................ 223
Personal Car Communicator................... 163
Petrol grade............................................. 296
Pocket park assist - PAP......................... 249
Panel lighting............................................. 84
Polishing.................................................. 386
Panic function.......................................... 160
Position/parking lamps.............................. 85
PAP - Active Park Assist.......................... 249
Power guide............................................... 65
Parcel shelf.............................................. 154
Power operated roller blind for glass
roof.......................................................... 103
Park Assist...............................................
backward............................................
fault indicator......................................
function...............................................
parking assistance sensors................
241
243
244
241
244
Park assist camera.................................. 245
settings............................................... 247
420
Passenger compartment filter................. 123
Power seat................................................. 79
Powershift gearbox.......................... 274, 308
Power windows......................................... 99
12 Alphabetical Index
Regeneration........................................... 299
Q
Queue Assist............................................ 205
Queue Assistant....................................... 205
R
Radar sensor........................................... 199
Limitations.......................................... 208
Rain sensor................................................ 97
Rear bulbs
location............................................... 364
Rear seat
Heating............................................... 129
Rearview and door mirrors
compass.............................................
door....................................................
electrically retractable.........................
heating................................................
interior.................................................
104
101
101
102
103
Rear window
heating................................................ 102
Recommendations during driving............ 293
Recommended child seats
table...................................................... 45
Relay/fuse box, see Fuses....................... 374
Remote control immobiliser..................... 159
Remote control key................. 156, 157, 158
battery replacement............................ 165
detachable key blade................. 163, 164
functions............................................. 160
loss..................................................... 156
range........................................... 161, 166
Remote control key system, type approval............................................................ 181
S
Safety lock
children................................................. 44
Safety mode.............................................. 40
moving the car...................................... 42
start attempt......................................... 41
Sealing fluid............................................. 338
Seat, see Seats.......................................... 77
Resetting the door mirrors....................... 101
Seatbelt......................................................
loosen...................................................
pregnancy.............................................
putting on.............................................
rear seat................................................
seatbelt reminder..................................
seatbelt tensioner.................................
Resetting the power windows................. 100
Seatbelt reminder...................................... 28
Retractable power door mirrors............... 101
Seatbelt tensioner................................ 28, 39
Reverse gear inhibitor.............................. 269
Seats.......................................................... 77
head restraints, rear.............................. 80
heating................................................ 129
Heating............................................... 129
lowering the front backrest................... 78
lowering the rear backrest.................... 80
power.................................................... 79
Remote control key with PCC
range................................................... 163
Resetting, trip meter........................ 112, 116
Road sign information............................. 187
Limitations.......................................... 189
operation............................................. 187
Roof load, max. weight............................ 395
Rustproofing............................................ 387
25
27
27
26
28
28
28
12
Securing loads (Loading)......................... 150
Recovery.................................................. 310
Self Supporting run flat Tyres (SST)........ 328
Refrigerant............................................... 359
Sensus....................................................... 74
421
12 Alphabetical Index
Service position....................................... 366
Steering force level, see Steering force... 259
Service programme................................. 346
Steering lock............................................ 267
Set time interval....................................... 213
Steering wheel........................................... 82
keypad.................................................. 82
steering wheel adjustment.................... 82
Side airbag SIPS.................................. 35, 39
SIPS airbag................................................ 35
Skidding........................................... 293, 294
slippery driving conditions....................... 294
Soot filter................................................. 299
SOOT FILTER FULL................................. 299
12
Storage spaces
driver's side........................................ 145
glovebox............................................. 146
tunnel console.................................... 145
spare wheel..................................... 317, 318
installation........................................... 320
taking out............................................ 318
Storage spaces in the passenger compartment.................................................. 143
Speed limiter............................................ 189
alarm for speed exceeded.................. 192
deactivation........................................ 193
getting started............................ 190, 191
temporary deactivation....................... 191
Symbols
indicator symbols..................... 62, 64, 66
warning symbols............................. 62, 64
Speed ratings, tyres................................. 317
Spin control............................................. 183
Stability and traction control system....... 183
Stability system....................................... 183
Stains....................................................... 388
Start/Stop................................................ 277
function and operation....................... 278
the engine does not stop.................... 279
Steering force, speed related.................. 259
422
Stone chips and scratches...................... 389
Switching off the engine.......................... 267
Symbols and messages
Adaptive Cruise Control..................... 211
Collision Warning with Auto
Brake.......................................... 222, 231
Driver Alert Control............................. 234
LKA..................................................... 240
System
tripping.................................................. 39
T
Tailgate
Locking/unlocking.............................. 173
Temperature
actual temperature............................. 122
Temperature control................................ 131
Total airing function......................... 121, 173
Towbar
detachable, attachment...................... 304
detachable, removal........................... 306
Towbar, see Towing equipment.............. 303
Towbar - detachable
attachment/removal.................... 304, 306
Towing..................................................... 308
towing eye.......................................... 309
Towing bracket........................................ 303
specifications...................................... 304
Towing capacity and towball load........... 396
Towing eye.............................................. 309
TPMS - Tyre Pressure Monitoring.... 324,
325, 326
Traction control........................................ 183
Trailer....................................................... 300
cable........................................... 300, 301
driving with a trailer............................ 300
snaking............................................... 307
12 Alphabetical Index
Trailer stability assist............................... 183
Tyre load index........................................ 316
Trailer Stability Assist.............................. 307
Tyre pressure label.................................. 322
Transmission............................................ 269
Tyre pressure monitoring. 324, 325, 326, 329
Adjust.................................................. 326
arming................................................. 327
deactivate........................................... 327
driveable punctured tyres (SST)......... 328
low tyre pressure................................ 329
recommendations............................... 328
Transmission oil
volume and grade............................... 403
Transponder.............................................. 19
Tread depth............................................. 315
Tread wear indicators.............................. 314
Trip computer.................. 109, 114, 118, 119
analogue instrument panel................. 110
Trip meter.................................................. 70
Trip meter, resetting........................ 112, 116
Troubleshooting
Adaptive Cruise Control..................... 210
TSA - trailer stability assist ............. 183, 307
Tunnel console........................................
12 V socket.........................................
armrest................................................
cigarette lighter and ashtray...............
145
147
145
146
Tunnel detection........................................ 86
Type approval
radar system....................................... 259
remote control key system................. 181
tyre pressure monitoring..................... 339
Type designations................................... 392
Tyres
direction of rotation............................ 312
maintenance....................................... 312
pressure...................................... 322, 412
puncture repair................................... 331
specifications...................................... 412
tread depth......................................... 315
tread wear indicators.......................... 314
tyre pressure monitoring..... 324, 325,
326,
329
winter tyres......................................... 315
U
V
Vanity mirror...................................... 92, 147
Ventilation................................................ 125
Vibration damper..................................... 303
Volvo ID..................................................... 20
Volvo Sensus............................................. 74
W
Warning lamp
Adaptive Cruise Control..................... 199
collision warning system.................... 227
stability and traction control system.. 183
12
Warning lamps
Airbags – SRS....................................... 68
alternator not charging......................... 68
Fault in brake system........................... 68
Low oil pressure................................... 68
Parking brake applied........................... 68
seatbelt reminder............................ 28, 68
Warning................................................ 68
Unlocking
from the inside.................................... 172
from the outside................................. 170
Warning sound
collision warning system.................... 227
Unlocking with the key blade................... 169
Warning triangle....................................... 323
Warning symbols........................... 62, 64, 68
Tyre dimension........................................ 316
423
12 Alphabetical Index
Washer fluid
volume................................................ 404
Washer fluid, filling................................... 369
Washers
rear window.......................................... 98
washer fluid, filling.............................. 369
windscreen........................................... 98
Water and dirt-repellent coating.............. 387
Water-repellent surface, cleaning............ 387
Waxing..................................................... 386
12
Weights
kerb weight......................................... 395
Wheel bolts.............................................. 314
lockable.............................................. 314
Wheel rim, dimensions............................ 316
Wheel rims
cleaning.............................................. 386
Wheels
removal............................................... 319
snow chains........................................ 315
spare wheel........................................ 317
Wheels and tyres..................................... 317
Whiplash injury, WHIPS............................. 37
WHIPS
child seat/booster cushion................... 38
seating position.................................... 38
whiplash protection........................ 37, 39
424
Windows, rearview and door mirrors....... 387
Windscreen
heating........................................ 102, 132
Windscreen washing.................................. 98
Windscreen wiper...................................... 97
rain sensor............................................ 97
Winter driving........................................... 293
Winter tyres.............................................. 315
Wiper blades............................................
changing.............................................
Cleaning..............................................
replacing, rear window.......................
Service position..................................
366
367
368
368
366
Wipers and washing.................................. 97
TP 17522 (English), AT 1420, MY15, Printed in Sweden, Göteborg 2014, Copyright © 2000-2014 Volvo Car Corporation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement