ROUSH Mustang GT Charger Kit Supercharger Kit Installation instructions
Below you will find brief information for Supercharger Kit Mustang GT ROUSHCharger Kit. The Supercharger Kit Mustang GT ROUSHCharger Kit is designed to increase horsepower and torque in the 2009 Ford Mustang GT 4.6L 3-Valve. The kit includes a ROUSHCharger, intercooler, and all necessary hardware for installation. The ROUSHCharger features a bypass system that allows the supercharger to operate at low RPMs for reduced noise and heat buildup, while still providing full boost when needed. The intercooler helps keep the air charge temperature cool for maximum performance.
Advertisement
Advertisement
PREMIUM FUEL REQUIRED
2009 Ford Mustang GT ROUSHCharger Kit
P/Ns: 13096066M90 (Black) & 13096066M90C (Chrome)
EO#: D-418-13
Installation Instructions
Applications:
2009 Ford Mustang GT 4.6L 3-Valve (w/ Manual & Automatic Transmissions).
Important Notes:
;
Before installing your Mustang ROUSHCharger Kit, please read the installation manual and verify that all items are present. Contact ROUSH Customer Service at 1-800-59-ROUSH, 9:00
AM to 5:00 PM EST weekdays, for any questions regarding fit or instructions that are unclear to you.
;
Premium fuel (91 octane or higher) is required to prevent “spark-knock” or detonation under certain operating conditions.
;
The use of fuel additives (ie. octane boosters) is not recommended. There is a possibility that these chemicals can damage your engine and cause drivability issues with your vehicle.
;
Operating your engine without the ROUSH PCM recalibration will result in engine damage or failure and will void your warranty.
13096066M90IM-AB_20090921PS Page 1 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
TABLE OF CONTENTS
PACKAGING LIST FOR COMPLETE ROUSHCHARGER KIT................................................ 3
EQUIPMENT AND SUPPLIES REQUIRED ........................................................................... 18
GLOSSARY OF TERMS ........................................................................................................ 19
INFORMATION ABOUT THE SUPERCHARGER BYPASS OPERATION ............................ 19
LIMIT OF LIABILITY STATEMENT ........................................................................................ 20
SAFETY PRECAUTIONS ...................................................................................................... 20
SECTION A – DISASSEMBLY............................................................................................... 21
SECTION B – MODIFICATIONS ........................................................................................... 31
Alternator Modification........................................................................................................ 31
Airbox Modification ............................................................................................................. 32
Heater Tube Assembly Modification ................................................................................... 34
Wiring Harness Modifications ............................................................................................. 35
SECTION C – SUBASSEMBLY ............................................................................................. 41
Intake Manifold Build Up..................................................................................................... 41
Fuel Rail Assembly............................................................................................................. 42
Alternator ............................................................................................................................ 43
SECTION D – INSTALLATION .............................................................................................. 45
Radiator Hose and Thermostat........................................................................................... 45
Intercooler Reservoir Mounting........................................................................................... 47
Intercooler Radiator Assembly Mounting ............................................................................ 50
Electric Water Pump Bracket Mounting .............................................................................. 53
Electric Water Pump Harness............................................................................................. 56
Intake Manifold and ROUSHCharger Installation ............................................................... 60
FEAD Assembly ................................................................................................................. 65
Air Intake System ............................................................................................................... 71
Coolant Hoses .................................................................................................................... 73
Air Induction System........................................................................................................... 75
Battery and Tray ................................................................................................................. 76
Vacuum System Connections............................................................................................. 76
Coolant Fill and Final Assembly ......................................................................................... 78
CARE AND MAINTENANCE OF OPTIONAL POLISHED ROUSHCHARGER...................... 81
WARRANTY........................................................................................................................... 81
13096066M90IM-AB_20090921PS Page 2 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
PACKAGING LIST FOR COMPLETE ROUSHCHARGER KIT
1
2 3 4 5
6 7 8 9
Part Ref Description
Induction Kit
1
Clean Air Tube
2
Coupler - Throttle Body End
3
#72 Hose Clamp (Throttle Body)
4
Hump Hose – Air Box End
5
6
#56 Hose Clamp (Tube side)
#52 Hose Clamp (Air Box side)
7
8
9
10
11
12
SAE Fitting - PCV Insert
Rubber Grommet - PCV Insert
1/4 20 X 5/8 Screw (Support Bracket)
1/4 Washers (Support Bracket)
#8 Washers (MAF)
8/32 Screws (MAF)
10 11 12
RPP Part Number
R07060059
R07060026
R07060029
----
R07060030
----
----
----
----
----
----
----
----
2
2
2
2
1
1
1
1
Qty
1
1
1
2
1
13096066M90IM-AB_20090921PS Page 3 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
14
13
15
Part Ref Description
Hardware Kit A - Air Box Modifications
13
14
15
Air Inlet
Bellmouth Insert
Adhesive - Loctite 4210 (3gm Tube)
16
17
18
Part Ref Description
Hardware Kit B - Induction
16
17
18
MAF Block-Off Plate w/ Gasket
Bracket- Tube Support
Bolts - Support Bracket to Intake (M6 x 1.0 x 13)
RPP Part Number
R07060060
R07060061
R07060062
R18090001
Qty
1
1
1
1
RPP Part Number
R07060064
R07060065
R07060066
N605771-S309
Qty
1
1
1
2
13096066M90IM-AB_20090921PS Page 4 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
NOTE: The Fuel Charging Assembly (R07060083) is shown above. It has been preassembled by ROUSH to ensure quality and simplify installation. It consists of parts 19
thru 34 which are shown individually below for reference only.
19 20
21
Part Ref Description
Fuel Charging Assembly
19
Upper Intake Manifold
20
Lower Intake Manifold
21
RPP Part Number Qty
R07060083 1
R07060034 1
R07060039 1
13096066M90IM-AB_20090921PS Page 5 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
26 27 28
29 30 31
32 33 34
Part Ref Description
Fuel Charging Assembly…Continued
22
23
24
25
26
27
28
29
ACT Sensor
Fitting - 90 deg. IPTS Reference (1/4")
Fitting - 90 deg. PCV Bubbler (3/8")
Gasket - Upper to Lower
Gasket - Intake Manifold Ports
Gasket - Water Crossover Right
Gasket - Water Crossover Left
Billet Tube - Intercooler Floating Tubes
30
31
O-Ring - Floating Tube
Bolt - Intercooler to Intake (M5 x 0.8 x 16)
32
33
34
Bolt - Upper to Lower Intake (M6 x 1.0 x 33)
Dowel - Intake to Supercharger
Washer - Intercooler to Intake
RPP Part Number Qty
R07060083 1
F6SF-12A697-AB 1
53525K11
391273-S100
G1ZE-9461-BB
R07060045
1
1
1
8
R07070001
R07070002
G1ZE-9L442-AA
2-115
SCS-05016-YZ
N808429-S437
388192-S
11-452-0033
1
1
2
4
11
12
2
11
13096066M90IM-AB_20090921PS Page 6 of 81 1-800-59-ROUSH
35
PREMIUM FUEL REQUIRED
36
37
Part Ref Description
35
Throttle Spacer
36
ROUSHCharger – Black
Optional
ROUSHCharger – Chrome
37
Fuel Rail
RPP Part Number Qty
R07060041 1
R07050086 1
R07050120 1
R07110001 1
13096066M90IM-AB_20090921PS Page 7 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
38
39
40
41
45
42 43
Part Ref Description
Hardware Kit C - Intake
38
39
40
41
Fuel Injectors
Gasket - Intake to Supercharger
Gasket - Supercharger to Spacer
Bolt - Heater Supply Tube Mounting (M6 x 1.0 x 13)
42
43
Bolt - Spacer to Supercharger (M8 x 1.25 x 33)
Bolt - Supercharger to Intake (M8 x 1.25 x 38)
44
45
Bolt - Throttle Body (M6 x 1.0 x 33)
Bolt - Intake to Cylinder Heads (M6 x 1.0 x 40)
44
RPP Part Number Qty
R07060046 1
R14010001 8
G1ZE-9H486-BA
G1ZE-9L437-BA
N605771-S309
1
1
2
N808920-S309
W705128-S437
N808429-S437
R18020004
6
6
4
11
13096066M90IM-AB_20090921PS Page 8 of 81 1-800-59-ROUSH
46
PREMIUM FUEL REQUIRED
49
48
47
51
52
53
55
56
54
57
58
50
Part Ref Description
46
Alternator Bracket
47
Serpentine FEAD Belt
48
49
50
Hardware Kit D - FEAD
Pulley - Idler B/S 76mm Flanged
Bracket - Intake to Alternator Rear
Bracket - Supercharger Studs to Alternator Bracket
51
52
Bolt – Rear Alternator Support (M5 x 0.8 x 10)
Nut – Rear Alternator Support (M5)
53
54
55
56
57
58
Bolt – Idler (M8 x 1.25 x 28 large washer)
Bolt – Alternator Support Brkts to Intk & FEAD Brkt (M8 x 1.25 x 25)
Bolt – FEAD Bracket to Intake (M8 x 1.25 x 38)
Bolt – Alternator (M8 x 1.25 x 55)
Nut – Supercharger to Alternator Support Bracket Front (M6)
Nut – Alternator (M8)
RPP Part Number
R07020013
R07020063
13096066M90HKD
R07020049
R07020056
R07020018
R18020059
R07020053
R18020060
W500224-S309
W705128-S437
N808130-S309
W520412-S309
W520413-S309
13096066M90IM-AB_20090921PS Page 9 of 81 1-800-59-ROUSH
2
2
2
2
1
2
2
2
2
Qty
1
1
1
2
1
PREMIUM FUEL REQUIRED
59
60
61
Part Ref Description
Hardware Kit E - PCV & Vacuum
59
60
61
PCV Purge
Vacuum Hose - Supercharger Bypass Circuit
Vacuum Cap – Throttle Spacer
RPP Part Number
R07040005
R07040006
R18140001
R07040040
Qty
1
1
1
1
13096066M90IM-AB_20090921PS Page 10 of 81 1-800-59-ROUSH
62
PREMIUM FUEL REQUIRED
A
B
63
C
64
D
Part Ref Description
Hardware Kit F - Wiring
62
Electrical Jumper - Intercooler Pump
63
64
Electrical Jumper - ACT
Alternator Charge Harness
A
B
C
D
Bolt – I/C Jumper Mounting (M6 x 1.0 x 13)
Nut – I/C Jumper Mounting (M6)
Bolt – Ground Strap to Cowl (M6 x 1.0 x 18)
Zip Tie – Ground Strap Bolt
RPP Part Number
13096066M90HKF
Qty
1
R07080016 1
1104-12B637-BA 1
R07080034 1
N605771 1
W520412 1
N605891 1
R18080003 1
13096066M90IM-AB_20090921PS Page 11 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
65
67 69
66
68 70
Part Ref Description
65
Box- PCM Return
66
Installation Manual
Hardware Kit G - Decals
67
68
69
70
Decal - Premium Fuel Only (IP Cluster)
Decal - Premium Fuel Only (Fuel Door)
Decal - 2005 Mustang Supercharged Belt Routing Diagram
E.O. Decal (2005-09 Models)
Warranty Card
RPP Part Number Qty
R07140023 1
13096066M90IM 1
R07040052 1
R07110004 1
R07110003 1
13106E072 1
R09000009 1
131019A505 1
13096066M90IM-AB_20090921PS Page 12 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
71
72
73
102
74
Part Ref Description
Hardware Kit I - Hose, Tubing, and Clamps
71
72
73
74
102
Bypass Circuit Radiator Hose
Clamps - 1.25" Radiator Hose
Tube Assembly - Intercooler
Tube - Heater Supply
Upper Radiator Hose
RPP Part Number Qty
R07010001 1
R07070004
R07070005
R07070014
R07070022
1
1
1
2
1
13096066M90IM-AB_20090921PS Page 13 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
75
76
77
78
79
80
81
83
Part Ref Description
Hardware Kit I - Hose, Tubing, and Clamps…Continued
75
3/4" Hose - LTR Outlet
76
77
3/4" Hose - Degas Outlet
3/4" Hose - Degas Inlet
78
79
80
81
82
83
3/4" Hose - LTR Inlet & I/C Outlet
3/4" Hose - Intercooler Inlet
3/4" Hose - Heater Supply
Clamps - 3/4" Hoses (Constant Tension)
Clamps - PCV Bubbler
PCV Bubbler Hose
82
RPP Part Number
R07010001
R07040007
83
Qty
1
1
1
1
2
1
1
14
2
1
13096066M90IM-AB_20090921PS Page 14 of 81 1-800-59-ROUSH
84
PREMIUM FUEL REQUIRED
85
86
87
88
Part Ref Description
84
Degas Bottle
85
Degas Bottle Cap
86
Intercooler Electric Water Pump
87
Bracket - Intercooler Pump Mounting
88
Intercooler Low Temp Radiator (LTR)
RPP Part Number
R07070007
XL3Z-8100-AA
F8YZ-8501-AA
R07070015
R07070047
Qty
1
1
1
1
1
13096066M90IM-AB_20090921PS Page 15 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
89
90 91
92
94
93
96
95 97
Part Ref Description
Hardware Kit J - Intercooler Circuit Fasteners
89
J-Clip - Degas Bottle & Pump Bracket Mounting (M6 Short)
90
Double-Sided Tape - Degas Bottle Mounting
91
Cap Screw - Degas Bottle Mounting (M6 x 1.0 x 8)
92
Washer - M6
93
Bolt - Pump Bracket (2) & I/C Tube Assembly Mounting (1) (M6 x 18)
94
95
Bolt - Degas Bottle Mounting (M6 x 1.0 x 33)
Bolt - Long Bumper Bolts (M8 x 1.25 x 35)
96
97
Bolt - 9N491 Tube Assembly Mounting (M16 x 40)
Nut - LTR Mounting (4) & Pump Bracket (1) (M8)
RPP Part Number Qty
R07070016 1
N623332-S301
R07030002
4
1
R18020010
R18030002
N605891-S437
1
1
3
N808429-S437
R18020007
R18020006
W520413-S309
2
4
1
5
13096066M90IM-AB_20090921PS Page 16 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
98
100
99
101
Part Ref Description
Hardware Kit K – 07+ Specific Hardware Kit
98
99
100
101
Bracket - Thermostat Support
Bracket - PS Pulley/Lower Radiator Hose Shield
Plug – Water Crossover w/ O-Ring Seal
Nut – PS Pulley Shield Bracket Mounting
RPP Part Number
13076066M90HKK
R07070025
R07070027
R07070026
W520412
If you are missing any items, please call us toll free at 1-800-59-ROUSH.
Qty
1
1
1
1
2
13096066M90IM-AB_20090921PS Page 17 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
EQUIPMENT AND SUPPLIES REQUIRED
• 1/4” and 3/8” Drive Ratchets with Extensions
• Metric and Standard Socket Sets (short and deep recommended)
• 1/2” Drive Ratchet or Breaker Bar
• Metric and Standard Wrench Sets
• 3/8” Drive Torque Wrench (7-35 ft-lb range)
• Short Phillips-head Screwdriver
• Hex Key Set
• Teflon pipe sealing tape or equivalent
• 5/8” Fuel Line Removal Tool
• T-20 Torx Bit Screwdriver or Socket
• Soldering Iron and Solder
• Wire Crimpers “W” type for OEM-style wiring connectors
• 1/8”, 9/64”, and ¼” Drill Bits and Drill motor
• Coolant (meeting G-05 specification)
• 6” Scale, Tape Measure, or Other Measuring Device
• Brake Parts Cleaner
• Assembly Lubricant (White Lithium Grease or Petroleum Jelly)
• Sharp Knife or Razor Blade
• Tie Straps (Zip Ties)
• Trim Pad Tool (for pushpin removal)
• Fender Cover (2)
• Medium Strength Thread Locker – Loctite 242 (blue) or equivalent
13096066M90IM-AB_20090921PS Page 18 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
GLOSSARY OF TERMS
ACT Air Charge Temperature Sensor (From the factory, this function is integrated into the
MAF sensor. With this kit, a separate ACT sensor is installed into the intake manifold)
CMCV Charge Motion Control Valve (Located on the back of the base intake manifold. This feature is not used with the ROUSHcharger)
ETC
IPTS
MAFS
PCM
PCV
SCBP
Electronic Throttle Control
Injection Pressure and Temperature Sensor
Mass Air Flow Sensor
Powertrain Control Module (a.k.a. ECM, ECU, PCU, EEC)
Positive Crankcase Ventilation
Supercharger Control Bypass Solenoid (A 3-way electronic vacuum control solenoid that allows the PCM to control the ROUSHcharger bypass to reduce heat buildup and noise during low throttle operation)
TPS
VMV
Throttle Position Sensor
Vapor Management Valve (Located on driver side strut tower)
Breakout Point A place in an electrical harness where the wiring for an individual component leaves
(breaks out of) the main harness to attach to an individual component.
INFORMATION ABOUT THE SUPERCHARGER BYPASS OPERATION
There is a great deal of misinformation about the function of supercharger bypass systems. The supercharger is a positive-displacement pump; that is, so long as it is rotating, it is always pumping air.
During low demand or high vacuum operation (i.e. idle, deceleration, and light throttle cruise), the pumping action is undesirable as it creates unwanted heat and noise. The bypass circuit, when open, prevents any pressure buildup across the supercharger and allows air to circulate through the rotors, allowing the supercharger to “idle” freely during these conditions. This results in reduced noise, and by reducing heat buildup in the intake, significantly improves street and strip performance. As throttle demand increases, the bypass circuit is closed, resulting in full performance from the supercharger. The bypass circuit is never used to limit or control boost during full-throttle operation and defeating or altering the bypass function will not result in improved performance in any condition, and will result in poor drivability.
13096066M90IM-AB_20090921PS Page 19 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
LIMIT OF LIABILITY STATEMENT
The information contained in this publication was accurate and in effect at the time the publication was approved for printing and is subject to change without notice or liability. Roush Performance Products
(RPP) reserves the right to revise the information presented herein or to discontinue the production of parts described at any time.
SAFETY PRECAUTIONS
STOP!
CAREFULLY READ THE IMPORTANT SAFETY PRECAUTIONS AND WARNINGS
BEFORE PROCEEDING WITH THE INSTALLATION!
Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety of the individual performing the kit installation. Improper installation due to the failure to correctly follow these instructions could cause personal injury or death. Read each step of the installation manual carefully before starting the installation.
1. Always wear safety glasses for eye protection.
2. Place the ignition switch in the OFF position.
3. Always apply the parking brake when working on the vehicle.
4. Block the front and rear tire surfaces to prevent unexpected vehicle movement.
5. Operate the engine only in well-ventilated areas to avoid exposure to carbon monoxide.
6. Do not smoke or use flammable items near or around the fuel system.
7. Use chemicals and cleaners only in well-ventilated areas.
8. Batteries can produce explosive hydrogen gas which can cause personal injury. Do not allow flames, sparks or flammable sources to come near the battery.
9. Keep hands and any other objects away from the radiator fan blades.
10. Keep yourself and your clothing away from moving parts when the engine is running.
11. Do not wear loose clothing or jewelry that can be caught in rotating or moving parts.
WORK SAFELY!
Perform this installation on a good clean level surface for maximum safety and with the engine turned off.
13096066M90IM-AB_20090921PS Page 20 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
SECTION A – DISASSEMBLY
The following section will guide you through the disassembly of the stock components. Special care should be taken to label fasteners and parts that are taken off during this procedure since many will be reused:
1.
Cover both fenders with fender covers to protect the vehicle finish.
2.
Release the fuel system pressure (NOTE: The following procedure is taken directly from the Ford
Service Manual).
WARNING: Fuel in the fuel system remains under high pressure even
when the engine is not running. Before working on or disconnecting any of the fuel lines or fuel system components, the fuel system pressure must be relieved. Failure to do so can result in personal injury.
WARNING: Do not smoke or carry lighted tobacco or open flame of
any type when working on or near any fuel-related components. Highly flammable mixtures are always present and can be ignited, resulting in personal injury.
a. Remove the fuel pump module fuse.
NOTE: The fuel pump module fuse is located in the underhood fuse box, location F41.
13096066M90IM-AB_20090921PS Page 21 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED b. Start the engine and allow it to idle until it stalls. c. After the engine stalls, crank the engine for approximately 10 seconds to make sure the fuel injector supply manifold pressure has been released. d. Turn the ignition switch to the OFF position. e. Reinstall the fuse that was removed in step a.
3.
Using an 8mm wrench, disconnect the (-) negative & (+) positive connections to the battery.
Remove the battery hold down bolt using an 8mm socket wrench. Remove the hold down & battery. With an 8mm socket wrench, remove the 3 bolts holding the battery tray to the vehicle.
Remove the battery tray.
Battery Tray Bolts
13096066M90IM-AB_20090921PS Page 22 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
4.
Disconnect the 3 PCM (Powertrain Control Module) connectors by lifting the grey levers over the connector back shell and lifting the connectors from their sockets. Remove the PCM by removing two 10mm bolts and pulling the PCM forward and lifting out of the engine compartment. Follow the instructions on the next page as soon as possible to help minimize the amount of time you are without a PCM.
Connector
Locations
Retaining Bolts
Important: Be sure to write your VIN number and phone number (in case we need to contact you for additional vehicle information) on the PCM using a permanent marker.
13096066M90IM-AB_20090921PS Page 23 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
INSTRUCTIONS FOR RETURNING THE PCM TO ROUSH FOR CALIBRATION
Outlined below are the instructions for returning your stock powertrain control module (PCM) to Roush
Performance Products so we can install our calibration to make the engine run properly with the new components. Please complete the “Warranty Registration Card” and include it, along with the
PCM, in the prepaid shipping box. The prepaid shipping box is set-up for next day delivery to us.
Once we receive your PCM, we will reprogram and return it back to you the same day for next-day delivery. Operating your engine without our calibration will result in engine damage or failure and
will void all warranty.
Note: It is important to reinstall the PCM in the vehicle it came from to prevent setting a trouble code and having to relearn the anti-theft code which can only be performed using specialized Ford Service Bay tools.
• If you haven’t already done so, write your vehicle identification number (VIN) and phone number
• on the PCM using a permanent marker.
• Remove the bubble wrap from inside the supplied shipping box and wrap it around the PCM to help prevent it from being damaged during shipping.
Place the wrapped PCM in the shipping box (R07140023).
• Complete the “Warranty Registration Card” (131019A505) and include it in the shipping
box along with the PCM.
• Fill in your name and address in the FROM area of the shipping label that is located inside the box. Follow the instructions on the box for sealing it shut.
• Peel the right label off and attach to the box where indicated.
• Retain the left side label for your records.
• Schedule directly to an agent. DO NOT use the automated option to schedule a pick up.
• Inform the agent you have a Prepaid FEDEX billable stamp package and you need a pick-up.
• If there are any issues with the shipping box we supply and you want to ship the PCM to us another way, the address for the PCM re-flash only is: Roush Powertrain Development, Building
57 – attn: PCM Flash, 777 Republic Drive, Allen Park, MI 48101
2009 Mustang ROUSHCharger Kit
Customer Name: ________________________ Contact Number: ________________________
VIN: ________________________
13096066M90IM-AB_20090921PS Page 24 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
5.
With the engine cool, remove the cap on the engine coolant degas bottle and drain the coolant using the petcock located on the lower passenger side of the radiator.
TIP: Connect 3/8” hose to the drain fitting next to the petcock and run into a clean drain pan or bottle. Use a ¾” wrench to open petcock and allow coolant to drain out of the fitting.
Drain Petcock
6.
Disconnect the PCV vent tube from the right-hand cam cover and clean air tube. Using an 8mm nut driver, loosen the 2 clamps at either end of the clean air tube. Remove the clean air tube from the throttle body and airbox.
Clamps
PCV Vent
Tube
13096066M90IM-AB_20090921PS Page 25 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
7.
Remove the MAF (mass air flow) connector by pulling the red locking tab back and pressing the black release tab. With a 10mm socket wrench, remove the airbox hold down bolt. Firmly grasp the airbox and pull up to remove it from the vehicle.
Hold down bolt
MAF Connector
8.
Disconnect ETC (electronic throttle control) & TPS (throttle position sensor) connectors from the throttle body (Pull the red locking tab back; press the black release tab to disengage the lock).
Remove the throttle body using an 8mm socket wrench (for the top two bolts) and a 10mm socket wrench (for the bottom two nuts). Remove the throttle body and the throttle body gasket from the intake manifold. Wipe the seal clean and dry and install it into the machined groove in the new throttle body spacer (P/N R07060041).
13096066M90IM-AB_20090921PS Page 26 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
9.
Remove the PCV line from the intake manifold and left-hand cam cover. Remove the VMV line from the intake manifold and position out of the way. Remove the vacuum line and electrical connector from the IPTS on the fuel rail and save for reuse. Remove the black safety clip from the fuel line connection. Place rags under the fuel rail, using a 5/8” fuel line tool (wrap additional rags around the tool) and disconnect the fuel line from the fuel rail. There will be some release of pressurized fuel, so be careful and proceed slowly.
VMV Line
IPTS
Fuel Rail Disconnect
PCV Line
10.
Disconnect the alternator harness from the positive battery terminal and remove the harness clips from the fuel rail studs.
.
13096066M90IM-AB_20090921PS Page 27 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
11.
Disconnect the wiring connectors from the fuel injectors (8). Remove the four 8mm stud bolts holding the fuel rail to the intake manifold and remove the fuel rail assembly with injectors. There may be some additional fuel leakage around the injectors. Clean all excess fuel before proceeding. Remove injectors and retainer clips from the fuel rail. Save the retainer clips for reuse.
Fuel Rail Holdown Studs
Retainer Clip
12.
Disconnect the CMCV connector located in the center rear of the intake manifold. Remove the brake booster vacuum line from the intake manifold. Pull the wiring harness off of the stud bolt on the driver side rear of intake manifold. Remove the ten fasteners which used to bolt the intake manifold to the cylinder heads. Save the rear stud for reuse. Remove the intake manifold. Use tape or equivalent to cover the cylinder head ports to prevent engine contamination.
Brake Booster Hose
Intake Manifold Bolts
Stud
CMCV Connector
Wire Harness hold down
13096066M90IM-AB_20090921PS Page 28 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
13.
Release the accessory drive belt by rotating the tensioner clockwise with a ½ “ breaker bar or ratchet and slip the belt off the water pump pulley and remove the belt completely. Disconnect the regulator connector and the battery cable from the alternator. Using a 10mm socket wrench, remove the four upper support bracket bolts. Remove the two 15mm alternator nuts and remove the alternator.
14.
Completely remove the upper radiator hose. Remove the two (2) Constant Tension Hose
Clamps from this hose for reuse. On the back side of the water crossover, disconnect the heater hose. Remove the water crossover using a 10mm socket wrench.
Crossover Tube Bolts
Upper Rad. Hose
Heater Hose
13096066M90IM-AB_20090921PS Page 29 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
15.
Disconnect the rubber portion of the heater hoses from the metal tubes at the rear of the righthand cylinder head. Remove the heater tube assembly from the engine by removing the stud on the back side of the passenger cylinder head and sliding off the water pump fitting in the block.
Disconnect Heater Hoses Here
Stud Bolt
16.
Completely remove the lower radiator hose assembly from the engine, radiator, and degas bottle.
17.
Remove the lower radiator hose retainer. Remove the clip on stud for the hose retainer.
Remove
13096066M90IM-AB_20090921PS Page 30 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
SECTION B – MODIFICATIONS
The following section will guide you through the required modifications of existing components and build up of the assemblies used to complete the installation. With the exception of the wiring modifications and intercooler pump bracket mounting, all of this work can be performed away from the vehicle.
Alternator Modification
1.
In order for the alternator to be installed in its new location, two of the original mounting ears must be removed. Using a band saw or similar cutting tool, remove the mounting ears shown. Be very careful to avoid getting debris inside of the alternator when removing these features. Use tape to cover any areas that lead into the alternator. Any debris that may get inside the alternator can lead to premature failure.
Before
After
13096066M90IM-AB_20090921PS Page 31 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
Airbox Modification
1.
Remove the MAF sensor from the stock airbox cover and install into the new clean air tube
(R07060026) using the two #8-32 screws and #8 washers provided in the induction kit. Install the rubber grommet and the SAE-style PCV fitting into the clean air tube. Install the tube support bracket (R07060066) in Hardware Kit B with the ¼-20x3/4” bolts and washers in the Induction Kit.
2.
Using the take out screws from the MAF, install the MAF block off plate w/gasket (R07060065) from Hardware Kit B onto the cover of the airbox. Torque the screws to 1.8 – 2.5 Nm.
13096066M90IM-AB_20090921PS Page 32 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
3.
Remove the dirty air inlet from the airbox. Install the supplied larger cross-section dirty air inlet
(R07060061). It may be necessary to clip off the top of the hook to ease installation. Be careful not to crack or damage the new dirty air inlet during installation.
Clip along the line shown to ease assembly
4.
Remove the airbox cover and stock air filter. Thoroughly clean the inside of the airbox cover with brake clean or equivalent. Spray brake clean on a shop rag and clean the bellmouth insert
(R07060062) on the rear face. Allow both parts to fully dry. Carefully install the bellmouth insert into the airbox cover using the supplied adhesive (Loctite 4210). Apply the adhesive generously to the bellmouth and apply pressure for approximately one hour to allow the glue to set up. Do not attempt to move the bellmouth once it sets as the adhesive takes a full twenty four hours to fully cure and must not be disturbed. Reinstall the air filter and reassemble the airbox.
13096066M90IM-AB_20090921PS Page 33 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
Heater Tube Assembly Modification
1.
The upper tube and hose on the heater tube assembly is not used (a new tube is supplied in the kit). Using a die grinder or air saw, cut the brackets that connect the two tubes together and deburr all sharp edges. Retain the lower tube which connects to the water pump and the mounting bracket for reinstallation.
Discard this tube
Cut
Save
13096066M90IM-AB_20090921PS Page 34 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
Wiring Harness Modifications
The following details the modifications to the factory engine harness which are necessary to complete the installation of this kit. These modifications should be done without removing the harness from the engine as it will be easier to verify final locations of the break out points. Extreme care must be taken to insure that wiring and/or its insulation is not accidentally damaged while removing the convoluted tubing. All of the convoluted tubing and various clips that are removed while making these changes are intended to be reinstalled in the same place unless otherwise noted.
TPS
ETC
MAF
Connectors for Wiring Circuits that will need to be modified
13096066M90IM-AB_20090921PS Page 35 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
1.
Make a note of the locations of the harness retaining clips and breakout points. With the harness still fastened to the engine with the factory retainers, carefully cut the tape off of the convoluted tubing and wiring harness on the drivers side of the engine (where the MAF & ETC branch out of the main harness) using a razor or utility knife. This area is highlighted in the following diagram.
The convoluted tubing is split from the factory so follow the split. Lift the wiring out of the convoluted tubing without disturbing the factory retainers wherever possible. Expose all of the internal wiring from the MAF/ETC split all the way around to the rear of the passenger side cam cover and past the rear retainer.
Pull wiring out from this section.
2.
Locate the 6-wire MAF sensor connector. Looking into the face of the connector with the release tab positioned up, the first two wires in the connector (IAT) from the right are grey and grey w/ red tracer. Cut both of these wires approximately 5 to 6 inches from the back of the connector.
MAF Connector
13096066M90IM-AB_20090921PS Page 36 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
3.
Seal the connector side of both cut IAT wires with pieces of heat shrink provided in the ACT electrical jumper (R07080010) in Hardware Kit F. Place two pieces of heatshrink tubing halfway onto the ends of the wires to be sealed and heat with a heat gun until it stops shrinking and sealant flows out from the open end of the tubing.
Sealing cut wire ends with Heat Shrink tubing
4.
Drag the 2 IAT wires out of the harness back from the MAF connector so that they break out with the #7 Coil Connector. Strip a ¼ inch of insulation from the end of each wire. Slide a short length of heat shrink tubing over both wires. Now using the Electrical Jumper (ACT) from the kit
(R07080010) lay the striped end of the Gray (IAT) wire into one side of the provided splice connector. From the Electrical Jumper (ACT) slide the ACT SIGNAL wire into the other side of the splice connector, and crimp using a W type crimping tool. Using a clean hot soldering iron, heat the wires (not the solder) in the splice connector until they are hot enough to melt the solder touched to them. Repeat the above for the IATRTN – ACT GROUND. Slide the heat shrink tubing over the solder joints and heat to shrink with a heat gun. Wrap ACT harness with tape.
#7 Coil
ACT Wire breakout point
13096066M90IM-AB_20090921PS Page 37 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
5.
Drag the remaining MAF wiring/connector out of the harness and back toward the dash panel, moving the MAF breakout point to before the driver side rear intake harness retainer. Remove the driver side rear intake harness retainer and turn it backwards. Wrap MAF harness with tape.
This will provide additional length to reach the new MAF position in the clean air tube.
Location before
Location after
6.
Pull the 2-wire ETC (electronic throttle control) wiring loose from the main harness and drag it back to the middle rear of the engine (same location as the MAF wiring in the previous step). At the middle rear of the engine, fold the ETC wiring back onto the still covered portion of the harness and route the ETC wiring with the harness over the breakout point near the #3 coil.
Wrap the ETC harness to the existing harness with electrical tape.
#3 Coil
13096066M90IM-AB_20090921PS Page 38 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
7.
Slide the driver side of the harness back into its convoluted tubing and re-tape.
8.
Locate the TPS (Throttle position sensor) connector and harness at the front of the passenger side valve cover. Remove the harness retainer for the timing cover bolt.
TPS wiring/connector
Harness Retainer
9.
Starting at the factory breakout point for the TPS, remove the electrical tape and convoluted tubing back to the #1 coil breakout point.
#1 Coil
Strip off this section of tape and convoluted tubing
13096066M90IM-AB_20090921PS Page 39 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
10.
Pull the 4-wire TPS wiring/connector to near the #1 Coil breakout point.
11.
Fold back the TPS leads to the break from the main harness near the #3 coil and tape onto existing still taped harness. Reinstall any convoluted tubing and re-tape the rest of the harness.
12.
Make sure there is at least 10” of free hanging lead for the TPS and ETC branches and wrap each with electrical tape.
13096066M90IM-AB_20090921PS Page 40 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
SECTION C – SUBASSEMBLY
Intake Manifold Build Up
1.
Remove Fuel Charging Assembly (R07060083) from packaging.
2.
Install the 3” long ¾” Heater Supply Hose and (1) ¾” Constant Tension Clamp (81) onto the heater Supply Tube (R07070014) from the Intercooler Hose Kit (R07010001). Place (1) ¾” CT clamp (81) over the intake manifold heater fitting. Install the Heater Supply Tube using (2) M6 x
1.0 x 13 mm bolts (N605771) from Hardware Kit C and torque to 8 – 12 Nm. Position the remaining loose hose clamp onto the hose and orient clamps as shown.
Heater Supply Tube Bolts
Intake Heater
Fitting
3.
Attach PCV Bubbler Hose (R07040007) to the bubbler fitting and install PCV Bubbler Clamps to each end of the hose (all parts are from Intercooler Hose Kit).
PCV Bubbler Hose
13096066M90IM-AB_20090921PS Page 41 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
4. Lube the O-ring on the Coolant Fill Plug (R07070026) from Hardware Kit K and install it into the new upper intake manifold. Torque to 12 – 18 Nm.
Fuel Rail Assembly
1.
Install the take off injector clips onto the new Fuel Injectors (R14010001) from Hardware Kit C.
Apply assembly lube to the injector O-rings and install them into the new Fuel Rail
(R07110001). Verify that the injector clips are properly seated onto the fuel rail injector cups.
13096066M90IM-AB_20090921PS Page 42 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
Alternator
1. Remove the (2) nuts shown from the back of the modified alternator
.
2. Install (2) hex nuts (R07020053) in place of the (2) nuts removed in the previous step. Torque hex nuts to 5 – 7 Nm. BE CAREFUL NOT TO OVERTIGHTEN THESE NUTS.
13096066M90IM-AB_20090921PS Page 43 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
3. Secure the Rear Alternator Bracket (R07020056) to the rear of the alternator using (2) M5 x 0.8 x
10mm bolts (R18020059). Torque bolts to 5 – 7 Nm. BE CAREFUL NOT TO OVERTIGHTEN
THESE BOLTS.
13096066M90IM-AB_20090921PS Page 44 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
SECTION D – INSTALLATION
The following section will guide you through the final installation of the kit into the vehicle. If you need to stop during any part of the installation, make sure you cover any open ports in the cylinder heads or intake manifold to prevent foreign material from contaminating your engine.
Radiator Hose and Thermostat
1. Install the Power Steering Pulley Bracket (R07070027) found in Hardware Kit K over the upper power steering pump studs. Retain with two M6 nuts (W520412) and torque to 8 – 12 Nm.
2. Remove the driver side noise filter retaining nut. Install the thermostat housing brace
(R07070025) over the noise filter stud. Replace the nut and torque to 20 – 30 Nm.
13096066M90IM-AB_20090921PS Page 45 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
3. Maneuver the long arched 1½” hose that exits the side of the Thermostat/Radiator Hose
Assembly (R07070029) under the power steering reservoir hoses, over the power steering pump, then down to the water inlet. Secure it at the engine with the supplied clamp. Secure the hose to the Power Steering Pulley Bracket using a zip tie through the holes in the bracket.
4. Route the 1 ½” hose that is connected to the bottom of the thermostat housing down to the radiator outlet. Check to ensure that the hose does not contact the A/C lines. Secure with the supplied clamp.
5. Route the ¾” hose that enters the side of the thermostat housing and expand to 1” near the open end to the Degas Bottle and connect to the bottom port. Secure with the clamp provided.
To Degas Bottle
To Engine Inlet
Bypass (no hose)
To Lower Radiator Outlet
13096066M90IM-AB_20090921PS Page 46 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
Intercooler Reservoir Mounting
1.
Using the Intercooler Degas Bottle (R07070007) with Degas Bottle Cap (XL3Z-8100-AA) as a template, place the bottle on the flat part of the electric fan shroud between the power steering reservoir and the engine coolant degas bottle. With the edge of the bottle at the edge of the electric fan shroud, mark the two mounting holes with a paint pen and drill two 5/16” holes through the fan shroud.
Mark and Drill here
13096066M90IM-AB_20090921PS Page 47 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
2.
Cut out the following template and use it to mark the third mounting hole and drill to 5/16”.
Mark and drill to 5/16”
3.
Clean the mating surfaces of the degas bottle and fan shroud with brake cleaner or rubbing alcohol. Peel and stick one side of the Double-Sided Tape (R07030002) provided in Hardware
Kit J, to the underside of the degas bottle.
Double-Sided Tape
13096066M90IM-AB_20090921PS Page 48 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
4.
Remove the upper fan shroud bolts and force the shroud toward the rear of the vehicle. Install
(2) J-Clips (N623332) from Hardware Kit J. Peel the second side of the double-sided tape and set the bottle on the fan shroud. Secure the intercooler degas bottle using (2) M6 x 1.0 x 33 mm bolts (N808429), and (1) M6 x 1.0 x 8 mm cap screw (R18020010) with washer
(R18030002) from Hardware Kit J and torque to 8 – 12 Nm. Reinstall the upper fan shroud bolts and torque to 8 – 12 Nm.
13096066M90IM-AB_20090921PS Page 49 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
Intercooler Radiator Assembly Mounting
1.
Remove the six push pin retainers highlighted below by pulling the center pin and remove the radiator trim cover.
Push Pin retainers
2.
Raise the vehicle and remove both front tires. Remove the three forward Phillips-head screws from each front wheel liner. Using a Phillips-head screwdriver, turn the five inner fender push pins ¼ turn to release the centers. Remove the pushpins and then remove the forward inner fenders.
Inner Fender Push Pin Locations
3 Phillips head screws
13096066M90IM-AB_20090921PS Page 50 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
3.
Remove the three lower close-out to radiator support screws (7mm). Remove the two upper bumper cover screws near the headlights (10mm). Remove the four front fender to bumper cover nuts inside the forward wheel well (10mm).
Upper Bumper
Cover Screws
Close-out screws
Fender to Bumper
Cover Nuts
4.
Reach inside the front wheel wells and unplug the front turn signals (there are four connectors total). Lift the front bumper cover slightly and pull partially off of the vehicle. Unplug the fog lights and set the front bumper cover aside.
5.
Remove the four push pins that retain the impact absorber to the front bumper beam and set the absorber aside.
Push Pins
13096066M90IM-AB_20090921PS Page 51 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
6.
Remove the four inner front bumper beam bolts. Save one bolt for reuse later.
Inner Bumper Bolts
7.
Install (4) Long Bumper Bolts (R18020007) from Hardware kit J in place of the four which were just removed and torque to 20 – 30 Nm. Install the Intercooler Radiator Assembly (R07060084) behind the bumper onto the new long bumper bolts. Install (4) LTR Mounting Nuts (W520413) from Hardware Kit J on the exposed end of the long bumper bolts and torque to 20 – 30 Nm.
Retaining Nut
Intercooler Radiator Assembly
Inner Bumper Bolt
13096066M90IM-AB_20090921PS Page 52 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
8.
Reinstall the impact absorber onto the front bumper beam using the take out pushpins.
9. Install the 12 ½” LTR Inlet Hose on the driver side of LTR with (1) ¾” constant tension clamp (81) and leave hanging. Install the 33 ¾” LTR Outlet Hose on the passenger side of the LTR with (1)
¾” constant tension clamp (81) and route up through the fender and into the engine compartment as illustrated below.
Electric Water Pump Bracket Mounting
1.
Cut out the following template. Line up the template with the tie down bracket inside the driver side wheel well. Center punch the “X”s marked on the template into the frame rail of the vehicle.
Drill two ¼” holes through the frame rail and de-burr the holes.
Cut this out and use as a template to locate holes
13096066M90IM-AB_20090921PS Page 53 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
This page left intentionally blank
.
13096066M90IM-AB_20090921PS Page 54 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
2.
Install (2) J-Clips (N623332) from Hardware Kit J and mount the Intercooler Pump Mounting
Bracket (R07070015) using (2) M6 x 1.0 x 18 mm bolts (N605891) onto the body. Torque bolts to
8 – 12 Nm
.
Slide the Intercooler Pump (F8YZ-8501-AA) into the bracket and secure using the bumper bolt removed earlier and a M8 nut (W520413) from Hardware Kit J. Torque the nut and bolt to 8 – 12 Nm.
Use take off bumper bolt in this location
3.
Connect the 12 ½” LTR Inlet Hose (previously installed to LTR) to the outlet of the pump with (1)
¾” constant tension clamp (81). Install the 31” Degas Bottle Outlet Hose onto the pump inlet with
(1) ¾” constant tension clamp (81). Route the Degas Bottle Outlet Hose up through the fender to the Degas Bottle as illustrated. Connect this hose to the bottom outlet of the Degas bottle using
(1) ¾” constant tension clamp (81).
Note: Route all intercooler hoses very carefully. It is critical to the performance of the intercooler that these hoses are not kinked once installed into the vehicle.
13096066M90IM-AB_20090921PS Page 55 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
Electric Water Pump Harness
1.
Disconnect the positive battery leads from the main positive battery cable at the fuse box.
Note: The bolt will remain retained by the cable’s terminal end.
2.
Locate the fuse holder branch of the Intercooler Pump Harness (R07080016). Run the short lead with the eyelet from the fuse holder to the Fuse box battery terminal.
3.
Reinstall the battery cable bolt through the I/C fuse lead and the main battery cable. Torque the bolt to 10 Nm (7.5 lb-ft).
4.
Secure the fuse holder to the strut tower using a 6mm bolt (N605771-S309) from Hardware kit F threaded into the tapped hole in the strut tower across from the fuse box’s main battery terminal.
5.
Route the rest of the I/C pump harness with the vehicle harness around the driver side of the
PCM bracket to the space ahead of the PCM connectors.
13096066M90IM-AB_20090921PS Page 56 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
6.
Locate the 6mm bolt threads protruding from the core support into the engine compartment ahead of the PCM brackets. Slide the I/C pump relay’s bracket over this stud and secure with a
6mm nut (W520412-S309). Torque the nut to 10 Nm (7.5 lb-ft).
6mm Bolt threads
Front of Vehicle
7.
Route the ground wire branch of the harness up to the ground screw directly above the relay.
Remove the ground screw and install the I/C Pump ground wire with all the factory grounds that were already in place with the bolt. Torque the bolt to 10 Nm (7.5 lb-ft).
13096066M90IM-AB_20090921PS Page 57 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
8.
Locate the square 16-pin connector on the driver side of the PCM bracket. Unplug the connector and remove the short section of convoluted tubing and electrical tape from the harness immediately behind the engine side (rearward half as mounted) of the connector. Locate the red w/yellow stripe wire in pin location #16. Cut this red wire about 1 inch back from the connector.
16-pin connector
Red/yellow stripe - #16
9.
Seal the connector end of the red wire using one piece of heat shrink provided with the
Intercooler Pump Wiring Harness Kit (R07080006).
Sealing cut wire ends with Heat Shrink tubing
13096066M90IM-AB_20090921PS Page 58 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
10.
Strip approximately 3/8” of insulation off the harness side of the red w/yellow wire. Place a piece of supplied heat shrink tubing over the remaining, non-terminated end of the Intercooler Pump
Wiring Harness. Strip approximately 3/8” of insulation off the end of the intercooler wire and connect to the red wire using the provided splice connector from the Intercooler Pump Wiring
Harness Kit and crimp using a W-type crimping tool. Using a clean, hot soldering iron, heat the wires (not the solder) in the splice connector until they are hot enough to melt the solder touched to them. Slide the heat shrink tubing over the solder joint and heat to shrink with a heat gun.
Reinstall the convoluted tubing and tape removed from the factory harness.
11.
Plug the connector back together. Route the remainder of the Intercooler Pump Wiring Harness over the radiator (following the existing harness) behind the headlamp on the driver side and into the inner fender area where the water pump bracket is mounted. Remove the top water pump bracket mounting bolt and install the wiring harness ground eyelet and re-torque the fastener.
Connect the wiring harness to the electric water pump.
Ground the pump wiring harness to the body in this location.
13096066M90IM-AB_20090921PS Page 59 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
Intake Manifold and ROUSHCharger Installation
1.
Install the modified heater tube assembly using the take out stud bolt. Be sure to lube the Orings with assembly lube before installing the heater tube to the water pump fitting in the block.
Torque the stud to 8 – 12 Nm.
2.
Remove the tape from the cylinder heads and clean the cylinder head to intake manifold mating surfaces using brake clean or rubbing alcohol.
3.
Set the intake manifold assembly down onto the cylinder heads. Be careful not to damage your sealing surfaces or gaskets during this step. Insert (2) intake mounting bolts (R18020004) from
Hardware Kit C into Holes A and B (shown below) and start the threads by hand. Do NOT tighten these fasteners. The intake must remain free to move along the cylinder head surfaces.
Hole B
Hole A
13096066M90IM-AB_20090921PS Page 60 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
4.
Install the Alternator Bracket (R07020013) onto the studs previously used to mount the alternator to the cylinder block and temporarily secure the bracket using the stock nuts.
5.
Use the FEAD bracket rear mounting bosses to properly align the intake manifold on the cylinder head surfaces by shifting the manifold from front to back and side to side. When you are finished, these features should be aligned in both the for-aft and side-to-side directions.
13096066M90IM-AB_20090921PS Page 61 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
6.
Once aligned, fasten the intake manifold using (11) M6 x 1.0 x 40mm bolts (R18020004) from
Hardware Kit C and the stock driver side rear stud (used to retain the wiring harness). Install these fasteners in the positions shown below and torque to 8 – 12 Nm in the sequence shown.
Remove the alternator bracket from the engine as it will be installed in a later step.
Stud
7.
Install the Intercooler Tube Assembly (R07070005) from Kit I onto the passenger side cylinder head using the M16 x 40mm Tube Mounting Bolt (R18020006) for the rear and (1) M6 x 1.0 x 18 mm I/C Tube Mounting Bolt (N605891) for the front from Hardware Kit J. Torque the M16 bolt to
45 Nm and the M6 bolt to 8 – 12 Nm. Carefully manipulate the wiring harness in the area shown.
Route the engine wiring harness between the tube assembly and coil #4 in
this area.
Route the engine wiring harness along the tube assembly in this area and zip tie to prevent damage to wiring. Pull the retainer clip from the
PCM bracket and secure the harness using zip ties away from all body-
mounted components.
M6x18 Bolt
M16x40 Bolt
13096066M90IM-AB_20090921PS Page 62 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
8.
Install intake to ROUSHcharger gasket (G1ZE-9H486-BA) over the dowels in the upper intake.
Remove the ROUSHcharger (R07050036) from the packaging and install using (6) M8 x 1.25 x
38mm bolts (W705128) provided in Hardware Kit C. Torque to 20 – 30 Nm in the sequence shown.
9.
Lube the fuel injector o-rings with assembly lube. Install the fuel rail and injectors into the intake manifold using the take off stud bolts and torque to 8 – 12 Nm. Be sure each injector is properly seated into the intake manifold.
13096066M90IM-AB_20090921PS Page 63 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
10.
Connect the IPTS, ACT, and all eight fuel injector and coil connectors. Route the MAF wiring across the manifold on the driver side between the valve cover and the fuel rail.
Fuel Injector Connection
(Coils similar)
ACT Connection
IPS Connection
13096066M90IM-AB_20090921PS Page 64 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
FEAD Assembly
1.
Install the Alternator Bracket (R07020013) onto the studs previously used to mount the alternator. Position the bracket onto alternator studs and loosely secure with the take-off M8 nuts. Use (2) M8 x 1.25 x 38mm bolts (W705128) from Hardware Kit D and to secure the alternator bracket to the intake manifold. Torque all nuts and bolts to 20 – 30 Nm.
2.
Install the Supercharger Studs to Alternator Bracket (R07020018) from Hardware Kit D using
(2) M6 nuts (W520412) and (1) M8 x 1.25 x 25mm bolt (W500224) also from Hardware Kit D.
Torque the nuts to 8 – 12 Nm and the bolt to 20 – 30 Nm.
13096066M90IM-AB_20090921PS Page 65 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
3.
Push the Alternator Charge Harness (R07080034) retainers onto the driver side fuel rail studs as shown below.
4.
Insert two M8 x 1.25 x 55mm bolts (N808130) and two M8 nuts (W520413), from Hardware Kit
D, through the alternator bracket. Be sure to leave enough room to insert the alternator.
Loosely secure the alternator charge harness eyelet to the alternator using the take off M8 nut.
Slide the alternator onto the bolts and route the charge harness under the rear alternator bracket (refer to picture in step #5 on next page). Torque M8 bolts to 20 – 30 Nm.
13096066M90IM-AB_20090921PS Page 66 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
5.
Secure the alternator to the intake using (1) M8 x 1.25 x 25mm Bolt (W500224). Torque to 20
Nm. Torque the nut securing the charge harness to the alternator to 15 – 20 Nm. Plug in smart charge connector to alternator. Take special care to make sure the charge harness is not pinched anywhere.
Route charge harness under the bracket in this area
W500224
6.
Remove the (2) plastic fasteners that hold the cowl grill in place. Lift the cowl grill for easier access to replace the factory screw that secures the grounding strap to the cowl with (1) M6 x
1.0 x 18.5mm bolt (N605891) at the arrow shown. Torque bolt to 8 – 12Nm and replace plastic fasteners.
Insert new bolt here
Remove plastic fasteners
13096066M90IM-AB_20090921PS Page 67 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
7.
Route the alternator charge harness through the grounding strap and secure it to the dash using (1) Stud Mount Zip Tie (R18080003). Push the Zip Tie onto the M6 Bolt from the previous step then wrap the zip tie around the cable.
8.
Secure the alternator charge harness to the dash by pushing the retainer (Christmas tree) to the factory dash panel tab.
13096066M90IM-AB_20090921PS Page 68 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
9.
Run the remaining smart charge section of the charge harness with the battery harness that runs along passenger side strut tower and secure it using the zip ties that have been preinstalled on the charge harness. Route wires under the main wiring harness bundle and plug into the connector.
Route wires along here
Route wires under main bundle
10.
Install FEAD Pulleys (R07020049) to the alternator bracket using (2) M8 x 1.25 x 28mm Idler bolts (R18020060). All parts can be found in Hardware Kit D. Torque bolts to 20 – 30 Nm.
13096066M90IM-AB_20090921PS Page 69 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
11.
Install the FEAD belt (R07020063) as shown. Using a ½ inch drive breaker bar or ratchet, rotate the belt tensioner clockwise and install the supplied belt.
13096066M90IM-AB_20090921PS Page 70 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
Air Intake System
1.
Install the S/C to Spacer Gasket (G1ZE-9L437-BA) from Hardware Kit C and Throttle Body
Spacer (R07060041) using (6) Spacer to S/C Bolts (N808920) from Hardware Kit C. Torque bolts to 20 – 30 Nm in sequence.
5
3
1
6
2
4
2.
Install the throttle body to the throttle spacer (the gasket was installed earlier when removing it from the stock intake manifold) using (4) M6 x 1.0 x 33mm Throttle Body Bolts (N808429).
Torque bolts to 8 – 12 Nm.
Note:
Mount the Throttle Body so that Electronic Throttle Control Motor is on the driver side.
13096066M90IM-AB_20090921PS Page 71 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
3.
Connect the newly relocated throttle body wiring.
13096066M90IM-AB_20090921PS Page 72 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
Coolant Hoses
1.
Reconnect the stock heater hoses at the back of the passenger side cylinder head using the original clamps. Install the 8” Intercooler Inlet hose and the 12 ½” Intercooler Outlet hoses using (4) ¾” constant tension clamps (81) from the intercooler hose kit.
Note: Ensure that the alternator charge harness installed in step #5 on page #57 is routed
over both intercooler hoses once installed.
2.
Connect the LTR Outlet hose routed from behind the passenger side headlamp to the lower
Intercooler tube using (1) ¾” constant tension clamp (81). Install the 17 ½” Degas Inlet hose from the upper intercooler tube to the upper degas bottle fitting using (2) ¾” constant tension clamps (81) from the intercooler hose kit. Install the new Bypass Circuit Radiator Hose
(R07070004) using (2) 1 ½” worm drive clamps from the intercooler hose kit.
13096066M90IM-AB_20090921PS Page 73 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
3.
Install the upper radiator hose (R07070022) between the intake manifold and the radiator.
Secure with the two (2) constant tension clamps removed from the factory upper radiator hose.
13096066M90IM-AB_20090921PS Page 74 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
Air Induction System
1.
Install the airbox assembly by reversing the removal instructions. Torque retaining bolt to 8 –
12 Nm.
2.
Install the throttle body end coupler (R07060029) with (1) #72 hose clamp from the Air
Induction Kit. Install the hump hose (R07060030) on the airbox (round) end of the clean air tube using (1) #56 hose clamp. Place the #52 hose clamp over the end of the hump hose and the second #72 hose clamp over the throttle body end of the tube. Slide the hose ends into place and start the (2) M6 x 1.0 x 13mm support bracket bolts (N605771) from Hardware
Kit B into the manifold. Position the couplers and tighten the clamps to 2 – 4Nm. Torque the support bracket bolts to 8 – 12 Nm. Plug in the MAF sensor.
3.
Connect the factory crankcase vent tube from the valve cover (near the oil fill) to the clean air tube. It is necessary to rotate the end fittings to achieve the desired routing illustrated below.
13096066M90IM-AB_20090921PS Page 75 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
Battery and Tray
1.
Install the battery tray by reversing the removal instructions. Torque the battery tray bolts to 8 –
12Nm.
2.
Place the battery in the tray and secure with battery hold down. Torque the battery hold down bolt to 8 – 12 Nm. Reinstall the heat protecting battery wrap over the battery.
Vacuum System Connections
1.
Connect the bubbler hose from the lower intake manifold to the throttle spacer (lower right 3/8” fitting) and secure 3/8” hose clamp from Hardware Kit I.
2.
Remove the 1/8” IPTS hose from the stock brake booster hose (at the plastic junction point).
Install the 1/8” take-off IPTS hose onto the IPTS (fuel rail sensor) and vacuum/boost 90 degree fitting on the manifold as shown below and insert the retaining clip onto the rear fuel rail stud bolt.
13096066M90IM-AB_20090921PS Page 76 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
3.
Install the new PCV purge tube (R07040006) from Hardware Kit E to the 5/8” SAE-style fitting on the throttle body spacer (lower left fitting). Reinstall the stock VMV hose to the upper front
3/8” SAE-style fitting.
4.
Install the fuel line to the fuel rail and secure using the safety clip.
5.
Install the 3/8” Vacuum Cap (R07040040) over the rear- most nipple on the throttle Spacer.
13096066M90IM-AB_20090921PS Page 77 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
6.
Connect the brake booster hose to the last open throttle body spacer fitting (top center port).
Connect the supplied vacuum hose (R18140001) between the upper port on the bypass actuator and the open tee fitting on the brake hose.
Coolant Fill and Final Assembly
1.
Fill the engine cooling system (using a proper G-05 coolant mixture) to the marked level on the radiator degas bottle.
2.
Using the same coolant mixture, fill the intercooler system. The coolant should be approximately one inch below the top of the cap.
Important:
Both coolant systems can trap a large amount of air. It is very important to verify that the air is purged and that coolant is flowing properly through both systems.
ROUSH Performance recommends vacuum filling both systems to properly evacuate the trapped air.
3.
Reinstall front bumper cover and inner fenders by reversing the removal instructions.
4.
Reinstall the front wheels/tires.
5.
Reinstall the newly flashed PCM by reversing the removal instructions.
6.
Reinstall the battery connections. Connect the positive cable first. Connect the battery end of the alternator charge harness using the same stud and nut which retained the factory harness.
Connect the negative cable to the battery.
7.
Inspect all underhood wiring harnesses for potential interference issues. Use zip ties to safely position the harness away from any areas of concern.
8.
Start the vehicle and check for fluid leaks, unusual noises, dash service lights, and unusual operation. If problems are detected, immediately stop the engine or vehicle, diagnose and repair the problem.
13096066M90IM-AB_20090921PS Page 78 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
9.
The “Premium Fuel” clear decal with white lettering (R07110004) is to be installed on the instrument cluster bezel, on the flat area below the small center gauges.
Tachometer Speedometer
Place Decal Here
10.
The “Premium Fuel” white decal with black lettering (R07110003) is to be placed on the lower half of the inside of the fuel filler door.
Place Decal Here
13096066M90IM-AB_20090921PS Page 79 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
11.
The Belt Routing Diagram (13106E072) is to be placed on the underside of the hood, on the driver side, opposite of the factory Vehicle Emission Control Information decal.
Place Decal Here
12.
The E.O. Decal is to be placed on driver side strut tower, adjacent to the air filter assembly.
Place Decal Here
13096066M90IM-AB_20090921PS Page 80 of 81 1-800-59-ROUSH
PREMIUM FUEL REQUIRED
CARE AND MAINTENANCE OF OPTIONAL POLISHED ROUSHCHARGER
The optional polished ROUSHCharger unit is uncoated, polished aluminum. As such, it will occasionally require polishing using a quality aluminum polishing compound to maintain its luster.
Many “spray-on” aluminum cleaners contain caustic chemicals and may discolor or damage the finish of the ROUSHcharger and, as such, are not recommended.
WARRANTY
All retail parts carry a 90-day warranty from the date of purchase. This warranty covers defects in materials or workmanship, and does not include (i) normal wear and tear, environmental conditions, improper installation; (ii) road hazards, misuse, abuse, neglect, accidents, collision, fire, theft, freezing, vandalism, riot, explosion, or objects striking the vehicle; (iii) misusing the vehicle, such as driving over curbs, overloading, racing, or using the vehicle as a stationary power source; (iv) altering, disassembling or modifying the parts; (v) defects caused or induced by failures, breakdowns, or damage by other parts, components or the vehicle; (vi) subjecting the parts to excessive moisture or water or any motor vehicle fluids (e.g.: oil, anti-freeze, battery acid, brake fluid, etc.); (vii) acts of God, natural disasters and other similar causes beyond the reasonable control of ROUSH; or (viii) application of chemicals that affect the parts. This Limited
Warranty does not cover surface deterioration of paint, trim, and appearance items that result from use and/or exposure to the elements, such as stone chips, scratches, bird droppings, lightning, hail, windstorm, dings, dents, earthquake, road salt, tree sap, water or flood.
ROUSH SHALL NOT BE LIABLE TO REIMBURSE CUSTOMER/DEALER FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES RESULTING FROM THE INSTALLATION OR USE OF
ANY PRODUCT SOLD THROUGH THIS CATALOG OR ARISING OUT OF ANY BREACH OF
WARRANTY. EXCEPT AS MAY BE STATED IN THIS CATALOG, ROUSH DISCLAIMS ALL
EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL
ROUSH’S LIABILITY EXCEED THE PRICE PAID BY CUSTOMER/DEALER FOR PRODUCTS
SOLD REGARDLESS IF ROUSH HAS BEEN ADVISED IN ADVANCE OF ANY POTENTIAL
PROBLEM OR IF A CLAIM IS BASED ON CONTRACT, TORT, STRICT LIABILITY, PRODUCT
LIABILITY OR OTHERWISE. SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF IMPLIED WARRANTIES OR THEIR DURATION, OR LIABILITY FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSIONS OR
LIMITATIONS MAY NOT APPLY.
This ROUSH Supercharger kit is designed and tested to function properly only on vehicles as they are equipped from the factory (completely stock powertrain). The use of aftermarket parts and equipment such as: cams, headers, nitrous oxide systems, other bolt-on performance parts, or any other performance parts not sold by, manufactured by, or approved of in writing by
ROUSH, will result in powertrain and supercharger kit damage and will not be the responsibility of ROUSH in any way.
If you have any questions or concerns please call 1-800-59-ROUSH.
13096066M90IM-AB_20090921PS Page 81 of 81 1-800-59-ROUSH

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Increased horsepower and torque
- ROUSHCharger with bypass system
- Intercooler for maximum performance
- All necessary hardware for installation
- Easy to install
- Premium fuel required