0127F - 2575 Manual - Thoroughbred Diesel
Page 20 of 20 Form 0127F 02/04/2004
Superchips Inc.
Page 1 of 20 Form 0127F 02/04/2004
Superchips Inc.
Superchips 2575 MAX Micro Tuner
General Motors 01-02 GM CK 4.3L V-6 Gasoline Engine
Trucks & SUV Series
Vehicle Programming Instructions – Section A
PLEASE READ THIS ENTIRE
INSTRUCTION SHEET
BEFORE YOU PROCEED
Thank you for choosing the
Superchips Model 2575 MAX
Micro Tuner, a remarkable
instrument that allows you to
install a Superchips performance
program specifically tuned for
your GM vehicle. You can
optionally remove the vehicle
speed limiter. Later model
vehicles also allow speedometer
correction to compensate for tire
height and/or gear changes. The
2575 MAX Micro Tuner is
intended for use on unmodified
stock engines.
Use High Octane Fuel
The Superchips performance program requires that you use at least 91 octane fuel. Using a
lower octane fuel while the performance program is installed may cause detonation that can
be harmful to your engine.
About Maximum Trailer Weight
The original manufacturer of your vehicle has specified a Maximum Trailer Weight for
your vehicle. It may be found in your vehicle owner’s manual.
This Superchips product is designed to increase your engine power and
performance. It does not change the engine, suspension or drive train characteristics
that limit the maximum trailer weight your vehicle is designed to tow. Towing trailer
weights above the maximum trailer weight specified by the vehicle manufacturer may
cause transmission or other damage.
If you wish to tow greater than the maximum trailer weight for your vehicle,
modifications to your vehicle may need to be made. Consult your performance auto
mechanic for the proper vehicle modifications.
Damage caused by towing weights greater than the maximum trailer weight specified
for your vehicle shall not be the responsibility of Superchips, Inc.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Page 2 of 20 Form 0127F 02/04/2004
Superchips Inc.
Page 19 of 20 Form 0127F 02/04/2004
Superchips Inc.
Superchips Inc. Return Policy
If for any reason during the first 30 days after purchase you are dissatisfied with the quality of this
product you may return it for a full refund of the purchase price (up to MSRP) less the shipping costs.
You will be asked to provide a copy of a Proof of Purchase. Put the product back in its original
packaging and return the product to the place of purchase. Your refund will be made as soon as possible
and in the same manner as your payment was made.
If these goods must be returned for repair or replacement according to the terms of this Limited
Warranty, you must first contact Superchips Customer Service at the number shown below to request a
Return Authorization (RA) number. You will be asked to provide a copy of a Proof of Purchase from an
authorized dealer and the reason for return. This RA number must be prominently displayed on the
outside of the shipping package. Put the goods back in their original packaging and return the goods
freight prepaid to Superchips at the address shown below. Goods received without an RA number will be
refused.
DO NOT ATTEMPT TO INSTALL THIS PRODUCT UNLESS YOU HAVE READ AND AGREE WITH THE
FOLLOWING:
Most Superchips Inc. products have the speed limiters increased. It is the buyer’s responsibility to
ensure that the vehicle is not driven faster than the speed rating of the tires on the vehicle in which the
Superchips Inc. product is installed and that the maximum speed rating of the engine is not exceeded. In
no case will Superchips Inc. be held liable if the Buyer exceeds these limits.
SUPERCHIPS INC. LIMITED WARRANTY
Superchips Inc., a Florida corporation, having its principle place of business at 1790 East Airport Blvd.,
Sanford, FL 32773, warrants this Superchips Inc. product (“Product”) as follows:
1.
Limited Warranty - Superchips Inc. warrants to the original purchaser (Buyer) that the Product
sold hereunder will be free from defects in material and workmanship for the lifetime of the Product. If the
Product does not conform to this Limited Warranty, the Buyer must notify Superchips Inc. in writing of the
claimed defects and demonstrate to Superchips Inc.’s satisfaction that said defects are covered by the
Limited Warranty. If the defects are properly reported to Superchips Inc., and the defects are of such
type and nature as to be covered by this Limited Warranty, Superchips Inc. shall at its own expense
furnish a replacement Product or, at Superchips Inc.’s option, replacement parts for the defective
Product. Shipping and installation of the replacement Product or parts shall be at the Buyer’s expense.
This Limited Warranty applies only to the original purchaser and is not transferable.
2.
Other Limits - THE FOREGOING IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURCHASE. Superchips Inc. does not warrant against damages
or defects arising out of improper or abnormal use or handling of the Product; against defects or
damages arising from improper installation (where installation is by persons other than Superchips Inc.
employees), against defects in products or components not manufactured by Superchips Inc., or against
damages resulting from such non-Superchips Inc. made products or components. Superchips Inc.
passes on to the Buyer the warranty it receives (if any) from the maker thereof of such non-Superchips
Inc. made products or components. This warranty also does not apply to Products upon which repairs
have been affected or attempted by persons other than employees of Superchips Inc. unless such
repairs are authorized in writing by Superchips Inc.
3.
Exclusive Obligation - THIS LIMITED WARRANTY IS EXCLUSIVE. The sole and exclusive
obligation of Superchips Inc. shall be to repair or replace the defective Product in the manner and for the
period provided above. Superchips Inc shall not have any other obligation with respect to the Product or
any part thereof, whether based on contract, strict liability or otherwise. Under no circumstances,
whether based on the Limited Warranty or otherwise, shall Superchips Inc be liable for incidental, special
or consequential damages.
4.
Other Statements - ORAL OR WRITTEN STATEMENTS BY SUPERCHIPS INC.’S EMPLOYEES
OR REPRESENTATIVES DO NOT CONSTITUTE WARRANTIES, shall not be relied upon by the Buyer,
and are not part of the contract for sale or this Limited Warranty.
5.
Entire Obligation - The Limited Warranty states the entire obligation of Superchips Inc. with
respect to the Product. If any part of the Limited Warranty is determined to be void or illegal, the
remainder shall remain in full force and effect.
Superchips Inc. Customer Service (407) 585-7000
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Superchips Inc.
Page 18 of 20 Form 0127F 02/04/2004
Code Interpretation
P1626
P1627
P1628
P1629
P1630
P1631
P1632
P1633
P1634
P1635
P1636
P1637
P1638
P1639
P1873
P1874
P1875
P1884
P1886
P1887
P1890
P1890
P1891
P1892
P1893
P1894
P1895
P1640
P1641
P1642
P1643
P1644
P1645
P1646
P1647
P1650
P1651
P1652
P1653
P1644
P1645
P1654
P1655
P1656
P1657
P1658
P1660
P1661
P1662
P1663
P1664
P1665
P1666
P1667
P1669
P1670
P1671
P1672
P1673
P1674
P1675
P1676
P1677
P1680
P1681
P1682
P1683
P1684
P1685
P1686
P1687
P1689
P1690
P1691
P1692
P1693
P1694
P1695
P1696
P1873
P1874
P1875
P1884
Theft Deterrent System Fuel Enable Circuit
A/D Performance
ECT Pull-Up Resistor
Theft Deterrent Sys - Cranking Signal
Theft Deterrent Sys - PCM In Learn Mode
Theft Deterrent Sys - Password Incorrect
Theft Deterrent System - Fuel disabled
Ignition Supply Power Circuit Lo Voltage
Ignition 1 Power Circuit Lo Voltage
5 Volt Reference Lo
PCM Stack Overrun
Generator L-Terminal Circuit
Generator F-Terminal Circuit
5 Volt Reference 2 Circuit
TCC Stator Temp Switch Circ Low
TCC Stator Temp Switch Circ High
4WD Low Switch Circ Electrical
TCC Enable/Shift Light Circ
Shift Timing Solenoid
TCC Release Switch Circ
ECM Data Input Circ
Throttle Pos Signal Input
Throttle Pos Sensor PWM Signal Low
Throttle Pos Sensor PWM Signal High
Eng Torque Signal Low Volts
Eng Torque Signal High Volts
TCM to ECM Torque Reduction Circuit
Driver 1 - Input Hi Voltage
FC Relay 1 Control Circuit
FC Relay 2 and 3 Control Circuit
Engine Speed Output Circuit
Traction Ctrl Delivered Torque Output Circ
EVAP Emission (EVAP) Vent Solenoid Control Circ
Driver 1 Line 6
Driver 1 Line 7
Driver 2 - Input Hi Voltage
Fan 1 Relay Control Circuit
VSS Output Circuit
Oil Level Lamp Control Circuit
TP Output Circuit
EVAP Solenoid Output Circuit
Service Throttle Soon Lamp Control Circuit
EVAP Purge Solenoid Control Circuit
Driver 2 Line 6
1-4 Up shift Solenoid Control Circuit
Starter Enable Relay Control Circuit
Cooling Fans Control Circuit
MIL Control Circuit
Cruise Control Inhibit Control Circuit
Oil Life Lamp Control Circuit
1-4 Up shift Lamp Control Circuit
Driver 3 Line 5
Driver 3 Line 6
Reverse Inhibit Solenoid Control Circuit
ABS Unit Expected
Driver 4
Driver 4 Line 1
Lo Engine Oil Level Lamp Control Circuit
Engine Hot Lamp Control Circuit
Tachometer Control Circuit
EVAP Vent Solenoid Control Circuit
Driver 4 Line 6
Driver 4 Line 7
Driver 5
Driver 5 Line 1
Driver 5 Line 2
Driver 5 Line 3
Driver 5 Line 4
Driver 5 Line 5
Driver 5 Line 6
Driver 5 Line 7
Delivered Torque Circuit Fault
ECM Loop Overrun
Coolant Gage Circuit Lo Voltage
Coolant Gage Circuit Hi Voltage
Tachometer Circuit Lo Voltage
Tachometer Circuit Hi Voltage
Remote Keyless Entry Circuit Lo
Remote Keyless Entry Voltage Hi
TCC Stator Temp Switch Circ Low
TCC Stator Temp Switch Circ High
4WD Low Switch Circ Electrical
TCC Enable/Shift Light Circ
Superchips Inc.
Code Interpretation
P1886
P1887
P1890
P1890
P1891
P1892
P1893
P1894
P1895
P1700
P1701
P1705
P1740
P1743
P1760
P1779
P1780
P1781
P1790
P1791
P1792
P1792
P1793
P1795
P1800
P1801
P1804
P1810
P1811
P1812
P1813
P1814
P1815
P1816
P1817
P1818
P1819
P1820
P1822
P1823
P1825
P1826
P1831
P1833
P1835
P1836
P1837
P1842
P1843
P1844
P1845
P1847
P1850
P1851
P1852
P1853
P1860
P1864
P1868
P1870
P1871
Shift Timing Solenoid
TCC Release Switch Circ
ECM Data Input Circ
Throttle Pos Signal Input
Throttle Pos Sensor PWM Signal Low
Throttle Pos Sensor PWM Signal High
Eng Torque Signal Low Volts
Eng Torque Signal High Volts
TCM to ECM Torque Reduction Circuit
Trans. MIL Request
Trans. MIL Request Circuit
P/N Signal Output Circuit
Torque Reduction Signal Circ
TP Signal from ECM
TCM Supply Volts Interrupted
Eng Torque Delivered to TCM Signal
Park/Neutral Pos [PNP] Switch Circ
Eng Torque Signal Circ
Trans Ctrl Module Checksum
Trans Ctrl Module Loop
Trans Ctrl Module Reprogrammable Memory
ECM to TCM Eng Coolant Signal
Trans Ctrl Module Stack Overrun
CAN Bus - Throttle Body Pos
TCM Power Relay Ctrl Circ
Perf Selector Switch Failure
Gnd Ctrl Relay
TFP Valve Pos Switch Circ
Maximum Adapt and Long Shift
Trans Over Temp Condition
Torque Ctrl
Torque Converter Overstressed
Trans Range Switch - Start In Wrong Range
TFP Valve Pos Sw. - Park/Neutral With Drive Ratio
TFP Valve Pos Sw. - Reverse With Drive Ratio
TFP Valve Pos Sw. - Drive Without Drive Ratio
Internal Mode Switch - No Start\Wrong Range
Internal Mode Switch Circ A Low
Internal Mode Switch Circ B High
Internal Mode Switch Circ P Low
Internal Mode Switch - Invalid Range
Internal Mode Switch Circ C - High
PC Solenoid Power Circ - Low Volts
A/T Solenoids Power Circ - Low Volts
Kick-Down Switch Circ
Kick-Down Switch Failed Open
Kick-Down Switch Failed Short
1-2 Shift Solenoid Circ Low Volts
1-2 Shift Solenoid Circ High Volts
Torque Reduction Signal Circ Desired By TCM
2-3 Shift Solenoid Circ Low Volts
2-3 Shift Solenoid Circ High Volts
Brake Band Apply Solenoid Circ
Brake Band Apply Solenoid Perf
Brake Band Apply Solenoid Low Volts
Brake Band Apply Solenoid High Volts
TCC PWM Solenoid Circ Electrical
Torque Converter Clutch Circ
Trans Fluid Life
Trans Component Slipping
Undefined Gear Ratio
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Page 3 of 20 Form 0127F 02/04/2004
Superchips Inc.
Your Vehicle’s STOCK Program
The MAX MicroTuner stores a copy of your vehicle’s original stock computer program. Your
vehicle computer must contain the manufacturer’s STOCK factory program. If you have used
a programmer from another aftermarket company you must use their product to return your
computer back to STOCK condition before proceeding. If you have a performance enhancing
chip installed, it must be removed.
Your Vehicle and Service Centers
If you need to return your vehicle to a service center, restore the vehicle program to its STOCK
program as described below at Step 3. The service center might reprogram your vehicle with an
updated program without your knowledge. If your vehicle has not been returned to its STOCK
program prior to service, the Superchips MAX Micro Tuner will no longer be able to program your
vehicle. Such a failure is not covered by the Superchips warranty.
Vehicle Preparation
Before connecting the MAX Micro Tuner to your vehicle, make sure that all power
draining accessories are turned off. Radio, lights, cell phones, etc., all need to be turned
off as the MAX Micro Tuner needs full battery voltage to program. Ensure your vehicle
battery is fully charged and not connected to a battery charger. Do not leave the MAX
Micro Tuner connected and unattended for any length of time to prevent unnecessary
battery drain.
Do not remove the programming cable during any programming sequence.
Important Note Regarding Storage of Your MAX Micro Tuner
It is recommended that you not store your MAX Micro Tuner in your vehicle if ambient
temperatures in your area fall below 32oF. Excessively low temperatures can cause
malfunction or damage to the MAX Micro Tuner that is not warranted by the Superchips, Inc.
1.
Connecting the MAX Micro Tuner to your vehicle
With the ignition switch in the OFF position, locate the diagnostic
connector under the dash near the steering wheel or under the
Glove box and connect the MAX Micro Tuner cable to the
diagnostic connector. (See Figure 1)
When connected, the MAX Micro Tuner will run a self-test,
displaying several start-up messages. Following the start up
messages, if the MAX Micro Tuner has been previously used to
program a vehicle, it will beep and display:
MICRO TUNER HAS
PROGRAMMED
VIN : XXXXXXXXXX
XXXXXX
Figure 1
This indicates the MAX Micro Tuner has been previously
used to program a vehicle and cannot program another. The
MAX Micro Tuner will continue to operate normally on the
original vehicle and may be used as a DTC Reader on other
GM vehicles.
2.
Selecting Tune Vehicle / Diagnostics
A= TUNE VEHICLE
B= DIAGNOSTICS
Turn the ignition switch to the RUN position. DO NOT START THE ENGINE.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Page 4 of 20 Form 0127F 02/04/2004
Superchips Inc.
Press the ‘A’ key on the keypad to continue with the tuning process.
Press the ‘B’ key to read and/or clear any Diagnostic Trouble Codes from the vehicle. See
DTC Reader Instructions and Interpretation in Section B starting on page 9.
3.
Vehicle Programming
If the ‘A’ key has been pressed, the MAX Micro Tuner will beep and display the message:
PRESS “A” TO
MODIFY OPTIONS
PRESS “YES” TO
PROGRAM PCM
Press ‘A’ to make changes as shown in Editing the Custom Options Settings at Step 7 that
follows.
Press ‘YES’ to install the Superchips Performance Program with or without user options
selected. The MAX Micro Tuner beeps and displays several screens as follows:
DO NOT REMOVE
CABLE
TURN OFF AND DO
NOT USE ANY
POWER CONSUMING
DEVICES
PRESS “YES” TO
ACKNOWLEDGE
Press the ‘Yes’ Key to acknowledge the warning. The MAX Micro Tuner continues with:
DO NOT REMOVE
CABLE UNTIL TOLD
PRESS “YES” TO
ACKNOWLEDGE
Press the ‘Yes’ key again to acknowledge the warning. The MAX Micro Tuner will then
begin establishing communications with the PCM.
Once the MAX Micro Tuner has established communications, if it has been previously
used to program your vehicle it will display:
PCM WAS ALREADY
MODIFIED!
PRESS “A” TO
REDOWNLOAD MODS
PRESS “YES” TO
DOWNLOAD STOCK
Press ‘YES’ to install the Original Stock Program.
Press ‘A’ to select user options as described in Editing the Custom Options
Settings at Step 7 below.
If the MAX Micro Tuner should fail to establish communications with the vehicle PCM, it
will beep and display the following prompts:
NO RESPONSE
FROM PCM
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Superchips Inc.
Page 17 of 20 Form 0127F 02/04/2004
Code Interpretation
P1352
P1353
P1354
P1355
P1356
P1357
P1358
P1359
P1360
P1361
P1362
P1363
P1364
P1365
P1366
P1367
P1368
P1370
P1371
P1372
P1374
P1375
P1376
P1377
P1380
P1381
P1390
P1391
P1392
P1393
P1394
P1395
P1396
P1397
P1398
P1399
P1403
P1404
P1405
P1406
P1407
P1408
P1409
P1410
P1415
P1416
P1418
P1420
P1421
P1423
P1431
P1432
P1433
P1441
P1442
P1450
P1451
P1460
P1480
P1481
P1483
P1500
P1501
P1501
P1502
P1503
P1504
P1508
P1509
P1510
P1511
P1514
P1515
P1516
P1517
P1518
P1519
P1520
P1521
P1522
P1523
P1524
P1525
IC Output Hi/Pulse Detected when GND Cyl. 2
IC Output Hi/Pulse Detected when GND Cyl. 3
IC Output Hi/Pulse Detected when GND Cyl. 4
IC Output Hi/Pulse Detected when GND Cyl. 5
IC Output Hi/Pulse Detected when GND Cyl. 6
IC Output Hi/Pulse Detected when GND Cyl. 7
IC Output Hi/Pulse Detected when GND Cyl. 8
Ign Coil Group 1 Ctrl Circ
Ign Coil Group 2 Ctrl Circ
Ign Coil Ctrl Circ Lo Volts
IC Cylinder 2 Not Toggling After Enable
IC Cylinder 3 Not Toggling After Enable
IC Cylinder 4 Not Toggling After Enable
IC Cylinder 5 Not Toggling After Enable
IC Cylinder 6 Not Toggling After Enable
IC Cylinder 7 Not Toggling After Enable
IC Cylinder 8 Not Toggling After Enable
IC 4X Ref Circ Too Many Pulses
IC 4X Ref Circ Too Few Pulses
Crankshaft Pos (CKP) Sensor A-B Correlation
3X Ref Circ
IC 24X Ref Circ Hi Volts
Ignition Gnd Circuit
IC Cam Pulse To 4X Ref Pulse
Misfire Detected - Rough Road Data Not Available
Misfire Detected - No Comm with Brake Ctrl Module
Wheel Speed Sensor1 - G - Sensor Circ
Wheel Speed Sensor1 - G - Sensor Circ Perf
Wheel Speed Sensor1 - G - Sensor Circ Lo Volts
Wheel Speed Sensor1 - G - Sensor Circ Hi Volts
Wheel Speed Sensor1 - G - Sensor Circ Intermittent
Wheel Speed Sensor2 - G - Sensor Circ
Wheel Speed Sensor2 - G - Sensor Circ Perf
Wheel Speed Sensor2 - G - Sensor Circ Lo Volts
Wheel Speed Sensor2 - G - Sensor Circ Hi Volts
Wheel Speed Sensor2 - G - Sensor Circ Intermittent
Exhaust Gas Recirc Sys Valve 1
Exhaust Gas Recirc (EGR) Closed Pos Perf
Exhaust Gas Recirc Sys Valve 3
EGR Valve Pintle Pos Circ
EGR Air Intrusion in Exhaust Supply to EGR Valve
Intake Manifold Press Sensor Circ
EGR Vacuum Sys Leak
Fuel Tank Press Sys
Sec Air Inject (AIR) Sys Bank1
Sec Air Inject (AIR) Sys Bank2
Sec Air Inject Sys Relay A Ctrl Circ Hi
Intake Air Lo Press Switch Circ Lo Volts
Intake Air Lo Press Switch Circ Hi Volts
Intake Air Hi Press Switch Circ Hi Volts
Fuel Level Sensor2 Circ Perf
Fuel Level Sensor2 Circ Lo Volts
Fuel Level Sensor2 Circ Hi Volts
EVAP Emission Sys Flow During Non-Purge
EVAP Vacuum Sw. Hi Volts During Ignition. On
Barometric Press Sensor Circ
Barometric Press Sensor Perf
Cooling Fan Control System
Fan Secondary Lo With Lo Fan On
Fan Secondary Lo With Hi Fan On
Eng Cooling Sys Perf
Starter Sig Circ
Theft Deterrent Sys
Vehicle Speed Sensor Circ Intermittent
Theft Deterrent Fuel Enable Sig Not Received
Theft Deterrent System - Password Incorrect
Vehicle Speed Output Circuit
IAC System Lo RPM
IAC System Hi RPM
Back Up Power Supply
Throttle Control System - Backup System Performance
Air Flow to TP Sensor Correlation Hi
Electronic Throttle System Throttle Position
Electronic Throttle Module Throttle Position
Electronic Throttle Module
Electronic Throttle Module to PCM Communication
Electronic Throttle Module Lo Volts Comm. Disable
Gear Indicator System
Transmission Engaged at Hi Throttle Angle
Park/Neutral to Drive/Reverse at Hi RPM
Elec. Throttle Control Throttle Return
TP Sen. Learned Cl. Throttle. Angle ß Out of Range
Throttle Body Service Required
Superchips Inc.
Code Interpretation
P1526
P1527
P1528
P1529
P1530
P1531
P1532
P1533
P1534
P1535
P1536
P1537
P1538
P1539
P1540
P1541
P1542
P1543
P1544
P1545
P1546
P1547
P1548
P1554
P1555
P1558
P1559
P1560
P1561
P1562
P1563
P1564
P1565
P1566
P1567
P1568
P1569
P1570
P1571
P1572
P1573
P1574
P1575
P1576
P1577
P1578
P1579
P1580
P1581
P1582
P1583
P1584
P1585
P1586
P1587
P1588
P1599
P1600
P1601
P1602
P1603
P1604
P1605
P1606
P1607
P1608
P1609
P1610
P1611
P1612
P1613
P1614
P1615
P1617
P1619
P1620
P1621
P1622
P1623
P1624
P1625
TP Sensor Learn Not Complete
Trans. Range/Pressure Switch Comparison
Governor
Heated Windshield Request Problem
Ignition Timing Adjustment Switch Circuit
A/C Lo Side Temperature Sensor Fault
A/C Evaporator Temp Sensor Circ Lo Voltage
A/C Evaporator Temp Sensor Circ Hi Voltage
A/C Hi Side Temp. Sensor Lo Voltage
A/C Hi Side Temperature Sensor Circuit
A/C System - ECT Over temperature
A/C Request Circuit Lo Voltage
A/C Request Circuit Hi Voltage
A/C Clutch Status Circ High Volts
A/C System Hi Pressure
A/C Hi Side Over Temperature
A/C System Hi Pressure Hi Temperature
A/C System Performance
A/C Refrigerant Condition Very Lo
A/C Clutch Relay Control Circuit
A/C Clutch Status Circuit Lo Voltage
A/C System Performance Degraded
A/C Recirculation Circuit
Cruise Engaged Circuit Hi Voltage
Electronic Variable Orifice Output
Cruise Control Servo Indicates Lo
Cruise Control Power Management Mode
Cruise Control Sys - Transaxle Not In Drive
Cruise Vent Solenoid
Cruise Vacuum Solenoid
Cruise Vehicle Speed/Set Speed Difference Too Hi
Cruise Control System - Vehicle Accel Too Hi
Cruise Servo Position Sensor
Cruise Control System - Engine RPM Too Hi
Cruise Control System - Active Braking Control Active
Cruise Servo Stroke Greater than Commanded in Cruise
Cruise Servo Stroke Hi While not in Cruise
Cruise Control Sys - Traction Control Active
TCS PWM Circuit No Frequency
ASR Active Circuit Lo Too Long
PCM/EBTCM Serial Data Circuit
EBTCM System - Stop Lamp Switch Circ Hi Volts
Extended Travel Brake Sw. Circ Hi Volts
BBV Sensor Circ Hi Voltage
BBV Sensor Circ Lo Voltage
BBV Sensor Circ Lo Vacuum
P/N to D/R At Hi Throttle Angle
Cruise Move Circuit Lo Voltage
Cruise Move Circuit Hi Voltage
Cruise Direction Circuit Lo Voltage
Cruise Direction Circ Hi Voltage
Cruise Control Disabled
Cruise Inhibit Control Circuit
Cruise Control Brake Switch 2 Circuit
Cruise Control Clutch Control Circuit Lo
Cruise Control Clutch Control Circuit Hi
Eng Stall or Near Stall Detected
PCM Battery/TCM Watchdog
Serial Comm. Problem With Device 1
Loss Of EBTCM Serial Data
Loss Of SDM Serial Data
Loss Of IPC Serial Data
Loss Of HVAC Serial Data
Serial Communication Problem With Device 6
Serial Communication Problem With Device 7
Serial Communication Problem With Device 8
Loss Of TCS Serial Data
Loss Of PZM Serial Data
Loss Of CVRTD Serial Data
Loss of IPM Serial Data
Loss of DIM Serial Data
Loss of RIM Serial Data
Loss of VTD Serial Data
Engine Oil Level Switch Circuit
Engine Oil Life Monitor Reset Circuit
Lo Coolant Circuit
PCM Memory Performance
Cylinder Select
Transmission Temp Pull-Up Resistor
Customer Snapshot Data Available
PCM System Reset
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Figure 2
Superchips Inc.
Page 16 of 20 Form 0127F 02/04/2004
Code Interpretation
P0794P0795P0796P0797P0798
P0799
P0801
P0803
P0804
P0805
P0806
P0807
P0808
P0809
P0810
P0811
P0812
P0813
P0814
P0815
P0816
P0817
P0818
P0820
P0821
P0822
P0823
P0824
P0825
P0830
P0831
P0832
P0833
P0834
P0835
P0836
P0837
P0838
P0839
P0840
P0841
P0842
P0843
P0844
P0845
P0846
P0847
P0848
P0849
P1000
P1031
P1032
P1105
P1106
P1107
P1108
P1109
P1111
P1112
P1113
P1114
P1115
P1116
P1117
P1118
P1119
P1120
P1121
P1122
P1125
P1130
P1131
P1132
P1133
P1134
P1135
P1136
P1137
P1138
P1139
P1140
P1141
P1143
P1144
Intermediate Shaft Speed Sensor Circ Intermittent
Pres Ctrl Solenoid C
Pres Ctrl Solenoid C Perf/Stuck Off
Pres Ctrl Solenoid C Stuck On
Pres Ctrl Solenoid C Electrical
Pres Ctrl Solenoid C Intermittent
Reverse Inhibit Ctrl Circuit Error
1-4 Up shift (Skip Shift) Solenoid Ctrl Circuit Error
1-4 Up shift (Skip Shift) Lamp Ctrl Circuit Error
Clutch Pos Sensor Circuit
Clutch Pos Sensor Circuit Range/Perf
Clutch Pos Sensor Circuit Lo
Clutch Pos Sensor Circuit Hi
Clutch Pos Sensor Circuit Intermittent
Clutch Pos Ctrl Error
Excessive Clutch Slippage
Reverse Input Circuit
Reverse Output Circuit
Tran Range Display Circuit
Up Shift Switch Circuit
Down shift Switch Circuit
Starter Disable Circuit
Driveline Disconnect Switch Input Circuit
Gear Lever X-Y Pos Sensor Circuit
Gear Lever X Pos Sensor Circuit
Gear Lever Y Pos Sensor Circuit
Gear Lever X Pos Sensor Circuit Intermittent
Gear Lever Y Pos Sensor Circuit Intermittent
Gear Lever Push/Pull Switch Circuit (Shift Anticipate)
Clutch Pedal Switch A Circuit
Clutch Pedal Switch A Circuit Lo
Clutch Pedal Switch A Circuit Hi
Clutch Pedal Switch B Circuit
Clutch Pedal Switch B Circuit Lo
Clutch Pedal Switch B Circuit Hi
4WD Switch Circuit
4WD Switch Circuit Range/Perf
4WD Switch Circuit Lo
4WD Switch Circuit Hi
Tran Fluid Pres Sensor/Switch A Circuit
Tran Fluid Pres Sensor/Switch A Circuit Range/Perf
Tran Fluid Pres Sensor/Switch A Circuit Lo
Tran Fluid Pres Sensor/Switch A Circuit Hi
Tran Fluid Pres Sensor/Switch A Circuit Intermittent
Tran Fluid Pres Sensor/Switch B Circuit
Tran Fluid Pres Sensor/Switch B Circuit Range/Perf
Tran Fluid Pres Sensor/Switch B Circuit Lo
Tran Fluid Pres Sensor/Switch B Circuit Hi
Tran Fluid Pres Sensor/Switch B Circuit Intermittent
Monitor Checks Not Complete-More Driving Required
HO2S Heater Current Monitor Ctrl Circ(Bank1&2,Sens1)
HO2S Heater Warm Up Ctrl Circ (Bank1&2, Sens1)
Sec Vacuum Sensor Circuit
Manif Abs Press (MAP) Sens Circ Intermittent Hi Volts
Manif Abs Press (MAP) Sens Circ Intermittent Lo Volts
BARO to MAP Sens Comparison Too Hi
Sec Port Throttle Sys
Intake Air Temp (IAT) Sens Circ Intermittent Hi Volts
Intake Air Temp (IAT) Sens Circ Intermittent Lo Volts
Intake Resonance Switchover Solenoid Ctrl Circ
Eng Coolant Temp (ECT) Sens Circ Intermittent Lo Volts
Eng Coolant Temp (ECT) Sens Circ Intermittent Hi Volts
ECT Sig Unstable or Intermittent
Eng Coolant Temp Sig Out-Of-Range Lo
Eng Coolant Temp Sig Out-Of-Range Hi
ECT Sig Out-Of-Range With TFT Sens
Throttle Pos (TP) Sens1 Circ
Throttle Pos (TP) Sens Circ Intermittent Hi Volts
Throttle Pos (TP) Sens Circ Intermittent Lo Volts
APP Sys
HO2S Circ Lo Variance Bank1 Sens1
HO2S Circ Lo Variance Bank1 Sens2
HO2S Circ Lo Variance Bank2 Sens1
HO2S Insufficient Switching Bank1 Sens1
HO2S Transition Time Ratio Bank1 Sens1
HO2S Lean Mean Bank1 Sens1
HO2S Rich Mean Bank1 Sens1
HO2S Bank1 Sens2 Lean Sys or Lo Volts
HO2S Bank1 Sens2 Rich or Hi Volts
HO2S Insuff Switching Bank1 Sens2
HO2S Transition Time Ratio Bank1 Sens2
HO2S Heater Ctrl Circ Bank1 Sens2
HO2S Bank1 Sens3 Lean Sys or Lo Volts
HO2S Bank1 Sens3 Rich or Hi Volts
Superchips Inc.
Page 5 of 20 Form 0127F 02/04/2004
Code Interpretation
P1145
P1153
P1154
P1155
P1156
P1157
P1158
P1159
P1161
P1163
P1164
P1165
P1170
P1171
P1185
P1186
P1187
P1188
P1189
P1190
P1191
P1200
P1201
P1202
P1203
P1211
P1212
P1214
P1215
P1216
P1217
P1218
P1219
P1220
P1221
P1222
P1225
P1228
P1231
P1234
P1237
P1240
P1243
P1245
P1250
P1257
P1258
P1260
P1270
P1271
P1272
P1273
P1274
P1275
P1276
P1277
P1278
P1280
P1281
P1282
P1283
P1285
P1286
P1287
P1288
P1300
P1305
P1310
P1315
P1320
P1321
P1322
P1323
P1324
P1335
P1336
P1345
P1346
P1350
P1351
HO2S Cross Counts Bank1 Sens3
HO2S Insufficient Switching Bank2 Sens1
HO2S Transition Time Ratio Bank2 Sens1
HO2S Lean Mean Bank2 Sens1
HO2S Rich Mean Bank2 Sens1
HO2S Bank2 Sens2 Lean Sys or Lo Volts
HO2S Bank2 Sens2 Rich or Hi Volts
HO2S Cross Counts Bank2 Sens2
HO2S Heater Ctrl Circ Bank2 Sens2
HO2S Bank2 Sens3 Lean Sys or Lo Volts
HO2S Bank2 Sens3 Rich or Hi Volts
HO2S Cross Counts Bank2 Sens3
Bank to Bank Fuel Trim Offset
Fuel Sys Lean During Acceleration
Eng Oil Temp Circ
EOT Circ Perf
EOT Sens Circ Lo Volts
EOT Sens Circ Hi Volts
Eng Oil Press (EOP) Switch Circ
Eng Vacuum Leak
Intake Air Duct Air Leak
Injector Ctrl Circ
(Alt. Fuel) Gas Mass Sens Circ Range/Perf
(Alt. Fuel) Gas Mass Sens Circ Lo Freq
(Alt. Fuel) Gas Mass Sens Circ Hi Freq
Mass Air Flow Circ Intermittent Hi
Mass Air Flow Circ Intermittent Lo
Inject Pump Timing Offset
Gnd Fault Detection Indicated
Fuel Solenoid Response Time Too Short
Fuel Solenoid Response Time Too Long
Inject Pump Calibration Circ
Throttle Pos Sens Ref Volts
Throttle Pos (TP) Sens2 Circ
Fuel Pump Sec Circ Lo
Injector Ctrl Circ Intermittent
Injector Circ Cylinder 2 Intermittent
Injector Circ Cylinder 3 Intermittent
Injector Circ Cylinder 4 Intermittent
Injector Circ Cylinder 5 Intermittent
Injector Circ Cylinder 6 Intermittent
Injector Circ Cylinder 7 Intermittent
Injector Circ Cylinder 8 Intermittent
Intake Plenum Switchover Valve
Early Fuel Evaporation Heater Circ
Supercharger Sys Over boost
Eng Coolant Over Temp - Protection Mode Active
Last Test Failed SCC ENTER More Info.
Accelerator Pedal Pos Sens A/D Converter Error
Accelerator Pedal Pos (APP) Sens1-2 Correlation
Accelerator Pedal Pos Sens2
Accelerator Pedal Pos Sens1
Injectors Wired Incorrectly
Accelerator Pedal Pos (APP) Sens1 Circ
Accelerator Pedal Pos Sens1 Circ Perf
Accelerator Pedal Pos Sens1 Circ Lo Volts
Accelerator Pedal Pos Sens1 Circ Hi Volts
Accelerator Pedal Pos (APP) Sens2 Circ
Accelerator Pedal Pos Sens2 Circ Perf
Accelerator Pedal Pos Sens2 Circ Lo Volts
Accelerator Pedal Pos Sens2 Circ Hi Volts
Accelerator Pedal Pos Sens3 Circ
Accelerator Pedal Pos Sens3 Circ Perf
Accelerator Pedal Pos Sens3 Circ Lo Volts
Accelerator Pedal Pos Sens3 Circ Hi Volts
Igniter Circ
Ign Coil 2 Pri Feedback Circ
Ign Coil 3 Pri Feedback Circ
Ign Coil 4 Pri Feedback Circ
C 4X Ref Circ Intermittent
Electronic Ign Sys Fault Line
EI Sys or Ign Ctrl Extra or Missing
IC 24X Ref Circ Lo Freq
Crank RPM Too Lo
CKP Circ
Crankshaft Pos (CKP) Sys Variation Not Learned
Crankshaft Pos (CKP)-Camshaft Pos (CMP) Correlation
Intake Camshaft Pos [CMP] Sens Sys Perf
Ign Ctrl Sys
Ign Coil Ctrl Circ Hi Volts
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Superchips Inc.
CHECK CABLE
TURN IGN ON
If the cable has not been connected properly or the ignition is not turned on, you will
need to disconnect the MAX Micro Tuner from the vehicle, turn the ignition OFF and
start over.
4.
Saving the Original STOCK Program for the Vehicle
If the vehicle PCM contains the manufacturer’s original STOCK program, it is first saved in
the MAX Micro Tuner to allow the vehicle to be reprogrammed to STOCK condition if
necessary. The MAX Micro Tuner will beep and display the message:
SAVING PCM
CALIBRATIONS
Upon completion of saving the stock program, the process of programming the vehicle with
the Superchips Performance Program begins. The MAX Micro Tuner will display:
PROGRAMMING…
*****
The bottom line of the displays shows the progress of programming.
Before programming can be completed, the MAX Micro Tuner will display a series of
messages that need to be followed carefully:
TURN IGN OFF
PRESS “YES” WHEN
IGN TURNED OFF
When ‘Yes’ has been pressed the Micro Tuner will display:
IMPORTANT NOTE
Do not interrupt the MAX Micro Tuner programming cycle or disconnect it from your vehicle
until the programming cycle is complete. The entire programming cycle can take several
minutes.
DO NOT START
UNTIL TOLD
This message will be displayed for 15 seconds. DO NOT START YOUR VEHICLE during
this time. After 15 seconds the Micro Tuner will display:
PROGRAMMING
COMPLETE
TURN IGN OFF
REMOVE CABLE
You may now disconnect the MAX Micro Tuner cable from the diagnostic port and start your
vehicle.
5. End of Programming Sequence
The programming sequence is now complete. Once the programming sequence has been
successfully accomplished on a vehicle, the MAX Micro Tuner becomes LOCKED to that
vehicle. The MAX Micro Tuner may not be used to tune any other vehicle. The MAX Micro
Tuner may be used on other GM vehicles as a DTC Reader.
6. Recovering the PCM
Occasionally during programming the MAX Micro Tuner will not be able to finish
programming. This can be caused by an interrupt in communications, removal of the
programming cable, power fluctuations, etc. These errors can cause a vehicle not to start.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Page 6 of 20 Form 0127F 02/04/2004
Superchips Inc.
The MAX Micro Tuner is equipped with a recovery mode to restore the vehicle to its stock
program in most situations if the following instructions are followed exactly.
It is very important to follow the recovery sequence described below precisely. It can be very
costly to repair or replace your PCM if the MAX Micro Tuner could have recovered your
vehicle and this sequence was not followed!
If an error occurs and the cable is still plugged into the connector under the dash, the MAX
Micro Tuner will automatically attempt to recover the PCM. If the cable has been removed or
dislodged, reconnect the cable to the connector. The MAX Micro Tuner will automatically go
into recovery mode when next powered on.
To recover your vehicle it will be necessary to start in a known condition, therefore the MAX
Micro Tuner will prompt you to:
TURN IGN OFF
PRESS “YES” WHEN
IGN TURNED OFF
MICRO TUNER WILL
NOW ATTEMPT TO
RECOVER PCM
TURN IGN ON
PRESS “YES” WHEN
IGN TURNED ON
After the ‘YES’ is pressed, the MAX Micro Tuner will attempt to determine if the PCM can be
recovered. If it cannot recover the PCM, the MAX Micro Tuner will then prompt you to do the
sequence above again. It will do this three times before prompting:
ERROR!
CALL SUPERCHIPS
If the MAX Micro Tuner can recover your PCM it will display the warning messages to turn off
and not use power consuming devices, and to not remove cable until told. The MAX Micro
Tuner will then display:
RECOVERING…
**
The bottom line of the displays shows the progress of recovery.
When recovery has been completed, the MAX Micro Tuner will display:
RECOVERY
SUCCESSFUL
RETURNED
TO STOCK
REMOVE CABLE
START VEHICLE
You may now disconnect the MAX Micro Tuner cable from the diagnostic port and start your
vehicle.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Page 15 of 20 Form 0127F 02/04/2004
Code Interpretation
P0600
P0601
P0602
P0603P0604
P0605
P0606
P0607
P0608
P0609
P0610
P0611
P0612
P0615
P0616
P0617
P0618
P0619
P0620
P0621
P0622
P0623
P0624
P0630
P0631
P0635
P0636
P0637
P0638
P0639
P0640
P0645
P0646
P0647
P0648
P0649
P0650
P0654
P0655
P0656
P0660P0661P0662P0663
P0664
P0665
P0666
P0667
P0668
P0669
P0670
P0671P0672P0673P0674P0675P0676P0677P0678P0679
P0680
P0681
P0682
P0683P0684P0700
P0701
P0702P0703
P0704P0705P0706P0707P0708P0709
P0710P0711P0712P0713P0714
P0715P0716
P0717
P0718-
Serial Comm Link Error
Internal Ctrl Mod Memory Check Sum Error
Ctrl Mod Programming Error
Internal Ctrl Mod KAM Error
Internal Ctrl Mod RAM Error
Internal Ctrl Mod ROM Error
PCM Processor Fault
Powertrain Ctrl Mod Perf
Powertrain Ctrl Mod VSS Output “A” Error
Powertrain Ctrl Mod VSS Output “B” Error
Powertrain Ctrl Mod Vehicle Options Error
Fuel Injector Ctrl Mod Perf
Fuel Injector Ctrl Mod Ctrl Circuit
Starter Relay Circuit
Starter Relay Circuit Lo
Starter Relay Circuit Hi
Alternative Fuel Ctrl Mod KAM Error
Alternative Fuel Ctrl Mod RAM/ROM Error
Generator Ctrl Circuit Error
Generator Lamp “L” Ctrl Circuit Error
Generator Field “F” Ctrl Circuit Error
Generator Lamp Ctrl Circuit Error
Fuel Cap Lamp Ctrl Circuit Error
VIN Not Programmed/Mismatch - ECM/PCM
VIN Not Programmed/Mismatch - TCM
Power Steering Ctrl Circuit
Power Steering Ctrl Circuit Lo
Power Steering Ctrl Circuit Hi
Throttle Actuator Ctrl Range/Perf bank1
Throttle Actuator Ctrl Range/Perf bank2
Manifold Intake Air Heater Ctrl Circuit
A/C Clutch Relay Ctrl Circuit
A/C Clutch Relay Ctrl Circuit Lo
A/C Clutch Relay Ctrl Circuit Hi
Immobilizer Lamp Ctrl Circuit
Cruise Ctrl Lamp Ctrl Circuit
Error Indicator Lamp (MIL) Ctrl Circuit Error
Eng RPM Output Circuit Error
Eng Hot Lamp Output Ctrl Circuit Malfunction
Fuel Level Output Circuit Error
Intake Manif Tuning Valve Ctrl Circuit bank1
Intake Manif Tuning Valve Ctrl Circ Lo bank1
Intake Manif Tuning Valve Ctrl Circ Hi bank1
Intake Manif Tuning Valve Ctrl Circuit bank2
Intake Manif Tuning Valve Ctrl Circuit Lo bank2
Intake Manif Tuning Valve Ctrl Circuit Hi bank2
Cruise 'On” Signal Error
Cruise 'Resume' Signal Error
Cruise “Set' Signal Error
Cruise “Coast' Signal Error
Glow plug Ctrl Circuit Error
Glow plug #1 Circuit failure
Glow plug #2 Circuit failure
Glow plug #3 Circuit failure
Glow plug #4 Circuit failure
Glow plug #5 Circuit failure
Glow plug #6 Circuit failure
Glow plug #7 Circuit failure
Glow plug #8 Circuit failure
Reserve for future Glow plug #9
Reserve for future Glow plug #10
Reserve for future Glow plug #11
Reserve for future Glow plug #12
Glow Plug Ctrl Mod to PCM Comm Circuit
Glow Plug Ctrl Mod to PCM Comm Circ Range/Perf
Tran Ctrl Sys Error
Tran Ctrl Sys Range/Perf
Tran Ctrl Sys Electrical
Brake Switch B Circuit Error
Clutch Pedal Pos Switch Input Circuit Error
Tran Range Sensor Circuit Error
Tran Range Sensor Circuit Range/Perf
Tran Range Sensor Circuit Lo Input
Tran Range Sensor Circuit Hi Input
Tran Range Sensor Circuit Intermittent
Tran Fluid Temp Sensor Circuit Error
Tran Fluid Temp Sensor Circuit Range/Perf
Tran Fluid Temp Sensor CKT Lo Input
Tran Fluid Temp Sensor CKT Hi Input
Tran Fluid Temp Sensor Circuit Intermittent
Input/Turbine Speed Sensor Circuit Error
Input/Turbine Speed Sensor Circuit Range/Perf
Input/Turbine Speed Sensor Circuit No Signal
Input/Turbine Speed Sensor Circuit Intermittent
Superchips Inc.
Superchips Inc.
Code Interpretation
P0719
P0720P0721P0722
P0723
P0724
P0725
P0726
P0727
P0728
P0730
P0731P0732P0733P0734P0735P0736
P0737
P0738
P0739
P0740P0741P0742P0743P0744
P0745P0746P0747
P0748
P0749
P0750P0751P0752P0753P0754
P0755P0756P0757P0758P0759
P0760P0761P0762P0763P0764
P0765P0766P0767P0768P0769
P0770P0771P0772P0773P0774
P0775P0776
P0777
P0778
P0779
P0780
P0781P0782P0783P0784P0785
P0786
P0787
P0788
P0789
P0790
P0791
P0792
P0793
Torque Converter/Brake Switch B Circuit Lo
Output Speed Sensor Circuit Error
Output Speed Sensor Range/Perf
Output Speed Sensor No Signal
Output Speed Sensor Intermittent
Torque Converter/Brake Switch B Circuit Hi
Eng Speed input Circuit Error
Eng Speed Input Circuit Range/Perf
Eng Speed Input Circuit No Signal
Eng Speed Input Circuit Intermittent
Incorrect Gear Ratio
Gear One Ratio Error
Gear Two Ratio Error
Gear Three Ratio Error
Gear Four Ratio Error
Gear Five Ratio Error
Reverse Gear Ratio Error
TCM Eng Speed Output Circuit
TCM Eng Speed Output Circuit Lo
TCM Eng Speed Output Circuit Hi
Torque Converter Clutch Circuit Malfunction
Torque Converter Clutch Circuit Perf/Stuck Off
Torque Converter Clutch Circuit Stuck On
Torque Converter Clutch Sys Electrical Failure
Torque Converter Clutch Circuit Intermittent
Pres Ctrl Solenoid Error
Pres Ctrl Solenoid Perf/Stuck Off
Pres Ctrl Solenoid Stuck On
Pres Ctrl Solenoid Electrical
Pres Ctrl Solenoid Intermittent
Shift Solenoid A Error
Shift Solenoid A Perf/Stuck Off
Shift Solenoid A Stuck On
Shift Solenoid A Electrical
Shift Solenoid A Intermittent
Shift Solenoid B Error
Shift Solenoid B Perf/Stuck Off
Shift Solenoid B Stuck On
Shift Solenoid B Electrical
Shift Solenoid B Intermittent
Shift Solenoid C Error
Shift Solenoid C Perf/Stuck Off
Shift Solenoid C Stuck On
Shift Solenoid C Electrical
Shift Solenoid C Intermittent
Shift Solenoid D Error
Shift Solenoid D Perf/Stuck Off
Shift Solenoid D Stuck On
Shift Solenoid D Electrical
Shift Solenoid D Intermittent
Shift Solenoid E Error
Shift Solenoid E Perf/Stuck Off
Shift Solenoid E Stuck On
Shift Solenoid E Electrical
Shift Solenoid E Intermittent
Pres Ctrl Solenoid B
Pres Ctrl Solenoid B Perf/Stuck Off
Pres Ctrl Solenoid B Stuck On
Pres Ctrl Solenoid B Electrical
Pres Ctrl Solenoid B Intermittent
Shift Error
1-2 Shift Error
2-3 Shift Error
3-4 Shift Error
4-5 Shift Error
Shift/Timing Solenoid Error
Shift/Timing Solenoid Range/Perf
Shift/Timing Solenoid Lo
Shift/Timing Solenoid Hi
Shift/Timing Solenoid Intermittent
Normal/Perf Switch Circuit Error
Intermediate Shaft Speed Sensor Circuit
Intermediate Shaft Speed Sensor Circuit Range/Perf
Intermediate Shaft Speed Sensor Circuit No Signal
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Page 14 of 20 Form 0127F 02/04/2004
Code Interpretation
P0379
P0380P0381P0382
P0385P0386
P0389
P0387
P0388
P0390
P0391
P0392
P0393
P0394
P0400P0401P0402P0403P0404
P0405
P0406
P0407
P0408
P0409
P0410
P0411P0412P0413P0414P0415
P0416P0417P0418
P0419
P0420P0421P0422
P0423
P0424
P0425
P0426
P0427
P0428
P0429
P0430P0431P0432
P0433
P0434
P0435
P0436P0437P0438P0439
P0440P0441P0442P0443P0444P0445P0446P0447
P0448
P0449
Error
P0450
P0451P0452P0453P0454
P0455P0456P0457
P0460P0461P0462
P0463
P0464
P0465
P0466
P0467
P0468
P0469
P0470
Timing Ref Hi Res Signal B No Pulses
Glow Plug Circuit Error Circuit A
Glow Plug Indicator Circuit Error
Glow Plug Circuit Error Circuit B
Crankshaft Pos Sensor B Circuit Error
Crankshaft Pos Sensor B Circuit Range/Perf
Crankshaft Pos Sensor B Circuit Intermittent
Crankshaft Pos Sensor B Circuit Lo Input
Crankshaft Pos Sensor B Circuit Hi Input
Crankshaft Pos Sensor B Circuit Error (bank2)
Crankshaft Pos Sensor B Circuit Range/Perf (bank2)
Crankshaft Pos Sensor B Circuit Lo Input (bank2)
Crankshaft Pos Sensor B Circuit Hi Input (bank2)
Crankshaft Pos Sensor B Circuit Intermittent (bank2)
Exhaust Gas Recirculation Flow Error
Exhaust Gas Recirculation Flow Insuff Detected
Exhaust Gas Recirculation Flow Excessive Detected
Exhaust Gas Recirculation Circuit Error
Exhaust Gas Recirculation Circuit Range/Perf
Exhaust Gas Recirculation Sensor A Circuit Lo
Exhaust Gas Recirculation Sensor A Circuit Hi
Exhaust Gas Recirculation Sensor B Circuit Lo
Exhaust Gas Recirculation Sensor B Circuit Hi
Exhaust Gas Recirculation Sensor A Circuit
Sec Air Injection Sys Error
Sec Air Injection Sys Incorrect Flow Detected
Sec Air Injection Sys Switching Valve A Circ Error
Sec Air Injection Sys Switching Valve A Circ Open
Sec Air Injection Sys Switching Valve A Circ Shorted
Sec Air Injection Sys Switching Valve B Circuit Error
Sec Air Injection Sys Switching Valve B Circ Open
Sec Air Injection Sys Switching Valve B Circ Shorted
Sec Air Injection Sys Relay “A” Circuit Error
Sec Air Injection Sys Relay “B” Circuit Error
Catalyst Sys Efficiency Below Threshold (bank1)
Warm Up Catalyst Efficiency Below Thresh (bank1)
Main Catalyst Efficiency Below Threshold (bank1)
Heated Catalyst Efficiency Below Threshold (bank1)
Heated Catalyst Temp Below Threshold (bank1)
Catalyst Temp Sensor (bank1)
Catalyst Temp Sensor Range/Perf (bank1)
Catalyst Temp Sensor Lo Input (bank1)
Catalyst Temp Sensor Hi Input (bank1)
Catalyst Heater Ctrl Circuit (bank1)
Catalyst Sys Efficiency Below Threshold (bank2)
Warm Up Catalyst Efficiency Below Thresh (bank2)
Main Catalyst Efficiency Below Threshold (bank2)
Heated Catalyst Efficiency Below Threshold (bank2)
Heated Catalyst Temp Below Threshold (bank2)
Catalyst Temp Sensor (bank2)
Catalyst Temp Sensor Range/Perf (bank2)
Catalyst Temp Sensor Lo Input (bank2)
Catalyst Temp Sensor Hi Input (bank2)
Catalyst Heater Ctrl Circuit (bank2)
Evap Emission Ctrl Sys Error
Evap Emission Ctrl Sys Incorrect Purge Flow
Evap Emission Ctrl Sys Leak Detected (small leak)
Evap Emission Ctrl Sys Purge Ctrl Valve Circ Error
Evap Emission Ctrl Sys Purge Ctrl Valve Circ Open
Evap Emission Ctrl Sys Purge Ctrl Valve Circ Shorted
Evap Emission Ctrl Sys Vent Ctrl Circuit Error
Evap Emission Ctrl Sys Vent Ctrl Circuit Open
Evap Emission Ctrl Sys Vent Ctrl Circuit Shorted
Evap Emission Ctrl Sys Vent Valve/Solenoid Circ
Evap Emission Ctrl Sys Pres Sensor Error
Evap Emission Ctrl Sys Pres Sensor Range/Perf
Evap Emission Ctrl Sys Pres Sensor Lo Input
Evap Emission Ctrl Sys Pres Sensor Hi Input
Evap Emission Ctrl Sys Pres Sensor Intermittent
Evap Emission Ctrl Sys Gross Leak Detected
Evap Emission Ctrl Sys Very Small Leak Detected)
Evap Emission Ctrl Sys Leak (fuel cap loose/off)
Fuel Tank Level Indicator Circuit Error
Fuel Level Sensor Circuit Range/Perf
Fuel Level Sensor Circuit Lo Input
Fuel Level Sensor Circuit Hi Input
Fuel Level Sensor Circuit Intermittent
EVAP Purge Flow Sensor Circuit
EVAP Purge Flow Sensor Circuit Range/Perf
EVAP Purge Flow Sensor Circuit Lo Input
EVAP Purge Flow Sensor Circuit Hi Input
EVAP Purge Flow Sensor Circuit Intermittent
Exhaust Back Pres Sensor Circuit Error
Superchips Inc.
Superchips Inc.
Code Interpretation
P0471P0472P0473P0474
P0475P0476
P0477
P0478P0479
P0480
P0481
P0482
P0483
P0484
P0485
P0486
P0487
P0488
P0491
P0492
P0500P0501P0502
P0503P0505P0506P0507P0508
P0509
P0510
P0512
P0513
P0515
P0516
P0517
P0520
P0521
P0522
P0523
P0524
P0530
P0531
P0532
P0533
P0534
P0540
P0541
P0542
P0544
P0545
P0546
P0547
P0548
P0549
P0550
P0551P0552
P0553
P0554
P0560P0561
P0562P0563
P0564
P0565
P0566
P0567
P0568
P0569
P0570
P0571P0572
P0573
P0574
P0575
P0576
P0577
Exhaust Back Pres Sensor Circuit Perf
Exhaust Back Pres Sensor Circuit Lo Input
Exhaust Back Pres Sensor Circuit Hi Input
Exhaust Back Pres Sensor Intermittent
Exhaust Pres Ctrl Valve Error
Exhaust Pres Ctrl Valve Range/Perf
Exhaust Pres Ctrl Valve Lo Output
Exhaust Pres Ctrl Valve Hi Input
Exhaust Pres Ctrl Valve Intermittent
Cooling Fan 1 Ctrl Circuit Error
Cooling Fan 2 Ctrl Circuit Error
Cooling Fan 3 Ctrl Circuit Error
Cooling Fan Rationality Check Error
Cooling Fan Circuit Over Current
Cooling Fan Power/Ground Circuit Error
EGR Sensor B Circuit
EGR Throttle Pos Ctrl Circuit
EGR Throttle Pos Ctrl Range/Perf
Sec Air Injection Sys (bank1)
Sec Air Injection Sys (bank2)
Vehicle Speed Sensor (VSS) Error
Vehicle Speed Sensor Range/Perf
Vehicle Speed Sensor Lo Input
Vehicle Speed Sensor Noisy
Idle Ctrl Sys Error
Idle Ctrl Sys RPM Lower Than Expected
Idle Ctrl Sys RPM Higher Than Expected
Idle Ctrl Sys Circuit Lo
Idle Ctrl Sys Circuit Hi
Closed Throttle Pos Switch Error
Starter Request Circuit
Incorrect Immobilizer Key
Battery Temp Sensor Circuit
Battery Temp Sensor Circuit Lo
Battery Temp Sensor Circuit Hi
Eng Oil Pres Sensor/Switch Circuit Error
Eng Oil Pres Sensor/Switch Circuit Range/Perf
Eng Oil Pres Sensor/Switch Circuit Lo Voltage
Eng Oil Pres Sensor/Switch Circuit Hi Voltage
Eng Oil Pres Too Lo
A/C Refrigerant Pres Sensor Circuit Error
A/C Refrigerant Pres Sensor Circuit Range/Perf
A/C Refrigerant Pres Sensor Circuit Lo Input
A/C Refrigerant Pres Sensor Circuit Hi Input
Air Conditioner Refrigerant Charge Loss
Manifold Intake Air Heater Circuit
Manifold Intake Air Heater Circuit Lo
Manifold Intake Air Heater Circuit Hi
EGT Sensor Circuit bank1
EGT Sensor Circuit Lo bank1
EGT Sensor Circuit Hi bank1
EGT Sensor Circuit bank2
EGT Sensor Circuit Lo bank2
EGT Sensor Circuit Hi bank2
Power Steering Pres Sensor Circuit Error
Power Steering Pres Sensor Circuit Range/Perf
Power Steering Pres Sensor Circuit Lo Input
Power Steering Pres Sensor Circuit Hi Input
Power Steering Pres Sensor Circuit Intermittent
Sys Voltage Error
Sys Voltage Unstable
Sys Voltage Lo
Sys Voltage Hi
Cruise Ctrl Multi-Function Input Signal
Cruise Ctrl ON Signal Error
Cruise Ctrl OFF Signal Error
Cruise Ctrl RESUME Signal Error
Cruise Ctrl SET Signal Error
Cruise Ctrl COAST Signal Error
Cruise Ctrl ACCEL Signal Error
Cruise Ctrl/Brake Switch A Circuit Fail
Cruise Ctrl/Brake Switch A Circuit Lo
Cruise Ctrl/Brake Switch A Circuit Hi
Cruise Ctrl Sys Vehicle Speed Too Hi
Cruise Ctrl Input Circuit
Cruise Ctrl Input Circuit Lo
Cruise Ctrl Input Circuit Hi
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Page 7 of 20 Form 0127F 02/04/2004
Superchips Inc.
No Start after Programming? Don’t Panic!
In some vehicles equipped with the passive Vehicle Anti-Theft System or VATS, once the
MAX Micro Tuner begins saving the factory stock program, the THEFT light begins blinking
rapidly and may even blink in short and long pulses to alert the user to a problem. Since the
Superchips Max Micro Tuner is communicating directly with the PCM, no other devices may
interrupt. As a result, the VATS module flags this as an error or theft condition and goes into
‘THEFT’ mode. After the MAX Micro Tuner has completed the programming cycle, the PCM
is still fully able to communicate and appears normal. However, the vehicle may be in a No
Start Condition and the THEFT light will be blinking rapidly.
Corrective Procedure
This procedure should recover the vehicle and allow it to be started. Therefore, it is
recommended that the MAX Micro Tuner programming cycle be completed prior to recovery.
i.e. The user should allow the MAX Micro Tuner to upload the stock program and should
select their choice of performance files and any user options, if available. Following
instructions, they should complete the programming process.
Once the vehicle has been programmed with the selected performance program, complete
the following steps to reset the VATS THEFT condition if necessary.
Disconnect the Superchips MAX Micro Tuner & cable from the vehicle computer interface
connector.
If the vehicle will not start and the Theft Light is blinking rapidly
1.
Remove the Ground (-) cable from the battery post for a period of thirty minutes to
allow the vehicle DTC codes and Theft codes to clear.
2.
Re-attach the Ground cable to the battery and start the vehicle as you normally would.
Error Notification
In the event recovery is successful and you are able to start your vehicle, you may now
attempt to use the MAX Micro Tuner to program your vehicle again. Follow the on-screen
prompts. If recovery is unsuccessful, or for any reason the MAX Micro Tuner fails to
complete its programming cycle, an error message will be displayed on the unit. Please
make note of the message displayed and contact Superchips Customer Service. If you
need assistance please contact your local dealer or call Superchips Customer Service at
407-585-7000 M-F 8:00 AM till 5:00 PM. EST.
7.
Editing the Custom Options Settings
Editing the Speed Limiter Option Setting
The Speed Limiter option allows the user to remove the vehicle Speed Limiter. The MAX
Micro Tuner will beep and display the message:
REMOVE SPEED
LIMITER? Y OR N
If the “Yes” key is pressed, the MAX Micro Tuner will beep and display:
Z RATED TIRES ON
VEHICLE? Y OR N
Press ‘YES’ if the vehicle has high speed “Z-Rated” tires installed. If ‘NO’ is pressed, the
stock speed limiter will NOT be removed! The MAX Micro Tuner will respond with either:
SPEED LIMIT
DISABLED
or
STOCK SPEED
LIMIT USED
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Page 8 of 20 Form 0127F 02/04/2004
Superchips Inc.
Editing the Gear Ratio Option Setting
The Gear Ratio Option allows you to correct the Speedometer/Odometer when other than
stock gears are installed. You may leave the gear ratio at STOCK or use one of the following
optional ratios:
3.08, 3.42, 3.73, 4.10
Note: The Gear Ratio option is NOT supported for all vehicles.
The MAX Micro Tuner will beep and display the message:
DIFFERENT GEAR
RATIO? Y OR N
If you have a different gear ratio than what is stock for your vehicle, press “Yes”. The MAX
Micro Tuner will beep and display the message:
SELECT 3.08 GEAR
RATIO? Y OR N
If you are using a 3.08 gear ratio, press “Yes”, otherwise press “No” to display the next gear
ratio supported by the MAX Micro Tuner. The MAX Micro Tuner will cycle through the list of
gear ratios, returning to the Different Gear Ratio? prompt after the last.
When the desired gear ratio is selected by pressing “Yes”, or “No” is entered in response to
the Different Gear Ratio? prompt, the MAX Micro Tuner then displays the prompt:
DIFFERENT TIRE
HEIGHT? Y OR N
Editing the Tire Height Option Setting
If you are using other than the stock tire size for your vehicle, press “Yes”. The MAX Micro
Tuner will beep and display the messages:
PRESS > TO ADJUST
TIRE HEIGHT
PRESS “YES” TO
SELECT
26.00
The tire height can be increased in .25” increments by using the “>” key to 38.00”. Measure
your tire height from the ground to the top of the tire. For example, if your measured tire
height is 27.25 inches, you would press the “>” key five times.
The screen would change with each key press as shown below:
26.25
26.50
26.75
27.00
27.25
When you reach the desired tire height (in this example 27.25 inches) press “Yes” to select.
Attempting to increase tire height past 38.00” will cause the MAX Micro Tuner to return to the
Different Tire Height? Prompt.
When the desired tire height is selected by pressing “Yes”, or “No” is entered in response to
the Different Tire Height? prompt, the MAX Micro Tuner then beeps and displays the prompt:
CHANGES STORED
FOR DOWNLOADING
The MAX Micro Tuner then beeps and returns to Vehicle Programming at Step 3 above.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Page 13 of 20 Form 0127F 02/04/2004
Code Interpretation
P0204
P0205
P0206
P0207
P0208
P0209
P0210
P0211
P0212
P0213
P0214
P0215
P0216
P0217
P0218
P0219
P0220
P0221
P0222
P0223
P0224
P0225
P0226
P0227
P0228
P0229
P0230
P0231
P0232
P0233
P0234
P0235
P0236
P0237
P0238
P0239
P0240
P0241
P0242
P0243
P0244
P0245
P0246
P0247
P0248
P0249
P0250
P0251
P0252
P0253
P0254
P0255
P0256
P0257
P0258
P0259
P0260
P0261P0262
P0263
P0264P0265
P0266
P0267P0268
P0269
P0270P0271
P0272
P0273P0274
P0275
P0276P0277
P0278
P0279P0280
P0281
P0282P0283
P0284
P0285P0286
P0287
Injector Circuit Error - Cylinder 4
Injector Circuit Error - Cylinder 5
Injector Circuit Error - Cylinder 6
Injector Circuit Error - Cylinder 7
Injector Circuit Error - Cylinder 8
Injector Circuit Error - Cylinder 9
Injector Circuit Error - Cylinder 10
Injector Circuit Error - Cylinder 11
Injector Circuit Error - Cylinder 12
Cold Start Injector 1 Error
Cold Start Injector 2 Error
Eng Shutoff Solenoid Error
Injection Timing Ctrl Circuit Error
Eng Over temp Condition
Tran Over temp Condition
Throttle Sw B Circ Error/Eng Over speed Condition
Throttle Pos Sensor/Switch B Circuit Error
Throttle Pos Sensor/Switch B Circuit Range/Perf
Throttle Pos Sensor/Switch B Circuit Lo Input
Throttle Pos Sensor/Switch B Circuit Hi Input
Throttle Pos Sensor/Switch B Circuit Intermittent
Throttle Pos Sensor/Switch C Circuit Error
Throttle Pos Sensor/Switch C Circuit Range/Perf
Throttle Pos Sensor/Switch C Circuit Lo Input
Throttle Pos Sensor/Switch C Circuit Hi Input
Throttle Pos Sensor/Switch C Circuit Intermittent
Fuel Pump Relay Dvr Fail
Fuel Pump Relay Dvr Circuit Fail On
Fuel Pump Relay Dvr Circuit Fail Off
Fuel Pump Relay Dvr Intermittent
Eng Over boost Condition
Turbo Boost Sensor A Circuit Error
Turbo Boost Sensor A Circuit Perf
Turbo Boost Sensor A Circuit Lo Input
Turbo Boost Sensor A Circuit Hi Input
Turbo Boost Sensor B Circuit Error
Turbo Boost Sensor B Circuit Perf
Turbo Boost Sensor B Circuit Lo Input
Turbo Boost Sensor B Circuit Hi Input
Turbo Wastegate Solenoid A Error
Turbo Wastegate Solenoid A Range/Perf
Turbo Wastegate Solenoid A Lo
Turbo Wastegate Solenoid A Hi
Turbo Wastegate Solenoid A Error
Turbo Wastegate Solenoid A Range/Perf
Turbo Wastegate Solenoid A Lo
Turbo Wastegate Solenoid A Hi
Injection Pump Fuel Metering Ctrl A Error
Injection Pump Fuel Metering Ctrl A Range/Perf
Injection Pump Fuel Metering Ctrl A Lo
Injection Pump Fuel Metering Ctrl A Hi
Injection Pump Fuel Metering Ctrl A Intermittent
Injection Pump Fuel Metering Ctrl A Error
Injection Pump Fuel Metering Ctrl A Range/Perf
Injection Pump Fuel Metering Ctrl A Lo
Injection Pump Fuel Metering Ctrl A Hi
Injection Pump Fuel Metering Ctrl A Intermittent
Injector Circuit Lo - Cylinder 1
Injector Circuit Hi - Cylinder 1
Cylinder 1 Contribution/Balance Fault
Injector Circuit Lo - Cylinder 2
Injector Circuit Hi - Cylinder 2
Cylinder 2 Contribution/Balance Fault
Injector Circuit Lo - Cylinder 3
Injector Circuit Hi - Cylinder 3
Cylinder 3 Contribution/Balance Fault
Injector Circuit Lo - Cylinder 4
Injector Circuit Hi - Cylinder 4
Cylinder 4 Contribution/Balance Fault
Injector Circuit Lo - Cylinder 5
Injector Circuit Hi - Cylinder 5
Cylinder 5 Contribution/Balance Fault
Injector Circuit Lo - Cylinder 6
Injector Circuit Hi - Cylinder 6
Cylinder 6 Contribution/Balance Fault
Injector Circuit Lo - Cylinder 7
Injector Circuit Hi - Cylinder 7
Cylinder 7 Contribution/Balance Fault
Injector Circuit Lo - Cylinder 8
Injector Circuit Hi - Cylinder 8
Cylinder 8 Contribution/Balance Fault
Injector Circuit Lo - Cylinder 9
Injector Circuit Hi - Cylinder 9
Cylinder 9 Contribution/Balance Fault
Superchips Inc.
Superchips Inc.
Code Interpretation
P0288P0289
P0290
P0291P0292
P0293
P0294P0295
P0296
P0298P0300
P0301P0302P0303P0304P0305P0306P0307P0308P0309P0310P0311P0312P0313
P0314
P0320P0321P0322P0323
P0324
P0325
P0326P0327P0328P0329
P0330
P0331P0332P0333P0334
P0335
P0336P0337
P0338
P0339
P0340P0341P0342
P0343
P0344P0345
P0346
P0347
P0348
P0349
P0350
P0351P0352P0353P0354P0355P0356P0357P0358P0359P0360P0361
P0362
P0365
P0366
P0367
P0368
P0369
P0370
P0371
P0372
P0373
P0374
P0375
P0376
P0377
P0378
Injector Circuit Lo - Cylinder 10
Injector Circuit Hi - Cylinder 10
Cylinder 10 Contribution/Balance Fault
Injector Circuit Lo - Cylinder 11
Injector Circuit Hi - Cylinder 11
Cylinder 11 Contribution/Balance Fault
Injector Circuit Lo - Cylinder 12
Injector Circuit Hi - Cylinder 12
Cylinder 12 Contribution/Balance Fault
Eng Oil Over temp Condition
Random/Multiple Cylinder Misfire Detected
Fault Cylinder A-Misfire Detected (CYLINDER 1)
Fault Cylinder B-Misfire Detected (CYLINDER 2)
Fault Cylinder D-Misfire Detected (CYLINDER 3)
Fault Cylinder E-Misfire Detected (CYLINDER 4)
Fault Cylinder F-Misfire Detected (CYLINDER 5)
Fault Cylinder G-Misfire Detected (CYLINDER 6)
Fault Cylinder C-Misfire Detected (CYLINDER 7)
Fault Cylinder H-Misfire Detected (CYLINDER 8)
Fault Cylinder I-Misfire Detected (CYLINDER 9)
Fault Cylinder J-Misfire Detected (CYLINDER 10)
Fault Cylinder K-Misfire Detected (CYLINDER 11)
Fault Cylinder L-Misfire Detected (CYLINDER 12)
Misfire Detected with Lo Fuel
1 Cylinder Misfire (Cylinder not specific)
Ign/Distributor Eng Speed Input Circuit Error
Ign/Distributor Eng Speed Input Circ Range/Perf
Ign/Distributor Eng Speed Input Circuit No Signal
Ign/Distributor Eng Speed Input Circuit Intermittent
Knock Ctrl Sys Error
Knock Sensor1 Circuit Error (bank1/1 Sensor)
Knock Sensor1 Circuit Range/Perf (bank1/1 Sensor)
Knock Sensor1 Circuit Lo Input (bank1/1 Sensor)
Knock Sensor1 Circuit Hi Input (bank1/1 Sensor)
Knock Sensor1 Circuit Intermittent (bank1/1 Sensor)
Knock Sensor2 Circuit Error (bank2)
Knock Sensor2 Circuit Range/Perf (bank2)
Knock Sensor2 Circuit Lo Input (bank2)
Knock Sensor2 Circuit Hi Input (bank2)
Knock Sensor2 Circuit Intermittent (bank2)
Crankshaft Pos Sensor A Circuit Error
Crankshaft Pos Sensor A Circuit Range/Perf
Crankshaft Pos Sensor A Circuit Lo Input
Crankshaft Pos Sensor A Circuit Hi Input
Crankshaft Pos Sensor A Circuit Intermittent
Camshaft Pos Sensor Circuit Error (bank1/1 Sensor)
Camshaft Pos Sensor Circuit Perf (bank1/1 Sensor)
Camshaft Pos Sensor Circuit Lo Input (bank1/1 Sensor)
Camshaft Pos Sensor Circuit Hi Input (bank1/1 Sensor)
Camshaft Pos Sensor Circuit Intermittent (bank1/1 Sens)
Camshaft Pos Sensor Circuit Error (bank2)
Camshaft Pos Sensor Circuit Perf (bank2)
Camshaft Pos Sensor Circuit Lo Input (bank2)
Camshaft Pos Sensor Circuit Hi Input (bank2)
Camshaft Pos Sensor Circuit Intermittent (bank2)
Ignition Coil Primary/Sec Circuit Error
Ignition Coil A Primary/Sec Circuit Error
Ignition Coil B Primary/Sec Circuit Error
Ignition Coil C Primary/Sec Circuit Error
Ignition Coil D Primary/Sec Circuit Error
Ignition Coil E Primary/Sec Circuit Error
Ignition Coil F Primary/Sec Circuit Error
Ignition Coil G Primary/Sec Circuit Error
Ignition Coil H Primary/Sec Circuit Error
Ignition Coil I Primary/Sec Circuit Error
Ignition Coil J Primary/Sec Circuit (Glow Plug) Error
Ignition Coil K Pri/Sec Circuit (Glow Plug Indicator) Error
Ignition Coil L Primary/Sec Circuit Error
Crankshaft Pos Sensor B Circuit Error (bank1)
Crankshaft Pos Sensor B Circuit Range/Perf (bank1)
Crankshaft Pos Sensor B Circuit Lo Input (bank1)
Crankshaft Pos Sensor B Circuit Hi Input (bank1)
Crankshaft Pos Sensor B Circuit Intermittent (bank1)
Timing Ref Hi Res Signal A Error
Timing Ref Hi Res Signal A Too Many Pulses
Timing Ref Hi Res Signal A Too Few Pulses
Timing Ref Hi Res Signal A Intermittent/Erratic Pulses
Timing Ref Hi Res Signal A No Pulses
Timing Ref Hi Res Signal B Error
Timing Ref Hi Res Signal B Too Many Pulses
Timing Ref Hi Res Signal B Too Few Pulses
Timing Ref Hi Res Signal B Intermittent/Erratic Pulses
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Superchips Inc.
Page 12 of 20 Form 0127F 02/04/2004
Code Interpretation
P0010
P0011P0012P0013P0014
P0015
P0020
P0021
P0022
P0023
P0024
P0025
P0030
P0031P0032P0033
P0034
P0035
P0036
P0037P0038P0042
P0043
P0044
P0050
P0051P0052P0056
P0057P0058P0062
P0063
P0064
P0065P0066P0067
P0070
P0071
P0072
P0073
P0074
P0075
P0076
P0077
P0078
P0079
P0080
P0081
P0082
P0083
P0084
P0085
P0086
P0087
P0088
P0089
P0090
P0091
P0092
P0093
P0094
P0100
P0101
P0102P0103P0104
P0105P0106P0107P0108P0109P0110
P0111
P0112P0113P0114
P0115
P0116P0117P0118P0119
P0120P0121P0122-
A Camshaft Pos Actuator Circuit (bank1)
A Camshaft Pos Timing - Over-Advanced bank1)
A Camshaft Pos Timing - Over-Retarded (bank1)
B Camshaft Pos Actuator Circuit (bank1)
B Camshaft Pos Timing - Over-Advanced (bank1)
B Camshaft Pos Timing - Over-Retarded (bank1)
A Camshaft Pos Actuator Circuit (bank2)
A Camshaft Pos Timing - Over-Advanced (bank2)
A Camshaft Pos Timing - Over-Retarded (bank2)
B Camshaft Pos Actuator Circuit (bank2)
B Camshaft Pos Timing - Over-Advanced (bank2)
B Camshaft Pos Timing - Over-Retarded (bank2)
HO2S Heater Ctrl Circuit (bank1, Sensor1)
HO2S Heater Ctrl Circuit Lo (bank1, Sensor1)
HO2S Heater Ctrl Circuit Hi (bank1, Sensor1)
Turbo Charger Bypass Valve Ctrl Circuit
Turbo Charger Bypass Valve Ctrl Circuit Lo
Turbo Charger Bypass Valve Ctrl Circuit Hi
HO2S Heater Ctrl Circuit (bank1, Sensor2)
HO2S Heater Ctrl Circuit Lo (bank1, Sensor2)
HO2S Heater Ctrl Circuit Hi (bank1, Sensor2)
HO2S Heater Ctrl Circuit (bank1, Sensor 3)
HO2S Heater Ctrl Circuit Lo (bank1, Sensor 3)
HO2S Heater Ctrl Circuit Hi (bank1, Sensor 3)
HO2S Heater Ctrl Circuit (bank2, Sensor1)
HO2S Heater Ctrl Circuit Lo (bank2, Sensor1)
HO2S Heater Ctrl Circuit Hi (bank2, Sensor1)
HO2S Heater Ctrl Circuit (bank2, Sensor2)
HO2S Heater Ctrl Circuit Lo (bank2, Sensor2)
HO2S Heater Ctrl Circuit Hi (bank2, Sensor2)
HO2S Heater Ctrl Circuit (bank2, Sensor 3)
HO2S Heater Ctrl Circuit Lo (bank2, Sensor 3)
HO2S Heater Ctrl Circuit Hi (bank2, Sensor 3)
Air Assisted Injector Ctrl Range/Perf
Air Assisted Injector Ctrl Circuit/Circuit Lo
Air Assisted Injector Ctrl Circuit Hi
Ambient Air Temp Sensor Circuit
Ambient Air Temp Sensor Range/Perf
Ambient Air Temp Sensor Circuit Lo Input
Ambient Air Temp Sensor Circuit Hi Input
Ambient Air Temp Sensor Circuit Intermittent
Intake Valve Ctrl Circuit (bank1)
Intake Valve Ctrl Circuit Lo (bank1)
Intake Valve Ctrl Circuit Hi (bank1)
Exhaust Valve Ctrl Circuit (bank1)
Exhaust Valve Ctrl Circuit Lo (bank1)
Exhaust Valve Ctrl Circuit Hi (bank1)
Intake Valve Ctrl Circuit (bank2)
Intake Valve Ctrl Circuit Lo (bank2)
Intake Valve Ctrl Circuit Hi (bank2)
Exhaust Valve Ctrl Circuit (bank2)
Exhaust Valve Ctrl Circuit Lo (bank2)
Exhaust Valve Ctrl Circuit Hi (bank2)
Fuel Rail/Sys Pres - Too Lo
Fuel Rail/Sys Pres - Too Hi
Fuel Pres Regulator Perf
Fuel Pres Regulator Ctrl Circuit
Fuel Pres Regulator Ctrl Circuit Lo
Fuel Pres Regulator Ctrl Circuit Hi
Fuel Sys Leak Detected - Large Leak
Fuel Sys Leak Detected - Small Leak
Mass/Volume Air Flow Circuit Error
Mass/Volume Air Flow Circuit Range/Perf
Mass/Volume Air Flow Circuit Lo Input
Mass/Volume Air Flow Circuit Hi Input
Mass/Volume Air Flow Circuit Intermittent
Manifold Abs Pres/Baro Pres Circuit Error
Manifold Abs Pres/Baro Pres Circuit Range/Perf
Manifold Abs Pres/Baro Pres Circuit Lo Input
Manifold Abs Pres/Baro Pres Circuit Hi Input
Manifold Abs Pres/Baro Pres Circuit Intermittent
Intake Air Temp Circuit Error
Intake Air Temp Circuit Range/Perf
Intake Air Temp Circuit Lo Input
Intake Air Temp Circuit Hi Input
Intake Air Temp Circuit Intermittent
Eng Coolant Temp Circuit Error
Eng Coolant Temp Circuit Range/Perf
Eng Coolant Temp Circuit Lo Input
Eng Coolant Temp Hi Input
Eng Coolant Temp Intermittent
Throttle Pos Sensor/Switch A Circuit Error
Throttle Pos Sensor/Switch A Circuit Range/Perf
Throttle Pos Sensor/Switch A Circuit Lo Input
Superchips Inc.
Page 9 of 20 Form 0127F 02/04/2004
Code Interpretation
P0123P0124P0125P0126
P0127
P0128P0130
P0131P0132P0133P0134P0135P0136P0137P0138P0139
P0140P0141
P0142
P0143
P0144
P0145
P0146
P0147
P0148
P0149
P0150
P0151
P0152
P0153
P0154
P0155
P0156
P0157
P0158
P0159
P0160
P0161
P0162
P0163
P0164
P0165
P0166
P0167
P0168
P0169
P0170
P0171
P0172
P0173
P0174
P0175
P0176
P0177
P0178
P0179
P0180
P0181
P0182
P0183
P0184
P0185
P0186
P0187
P0188
P0189
P0190
P0191
P0192
P0193
P0194
P0195
P0196
P0197
P0198
P0199
P0200
P0201
P0202
P0203
Throttle Pos Sensor/Switch A Circuit Hi Input
Throttle Pos Sensor/Switch A Circuit Intermittent
Insuff Coolant Temp for Closed Loop Fuel Ctrl
Insuff Coolant Temp Stable Operation
Intake Air Temp Too Hi
Coolant Temp Below Thermostat
Oxy Sensor Circuit (bank1, Sensor1)
Oxy Sensor Circuit Lo Voltage (bank1, Sensor1)
Oxy Sensor Circuit Hi Voltage (bank1, Sensor1)
Oxy Sensor Circuit Slow Response (bank1, Sens1)
Oxy Sens Circ No Activity Detected (bank1 Sens1)
Oxy Sensor Heater Circuit (bank1, Sensor1)
Oxy Sensor Circuit (bank1, Sensor2)
Oxy Sensor Circuit Lo Voltage (bank1, Sensor2)
Oxy Sensor Circuit Hi Voltage (bank1, Sensor2)
Oxy Sensor Circuit Slow Response (bank1, Sensor2)
Oxy Sens Circ No Activity Detected (bank1 Sens2)
Oxy Sensor Heater Circuit (bank1, Sensor2)
Oxy Sensor Circuit (bank1, Sensor 3)
Oxy Sensor Circuit Lo Voltage (bank1, Sensor 3)
Oxy Sensor Circuit Hi Voltage (bank1, Sensor 3)
Oxy Sensor Circuit Slow Response (bank1, Sensor 3)
Oxy Sensor Circuit No Activity Detected (bank1 Sens3)
Oxy Sensor Heater Circuit (bank1, Sensor 3)
Fuel Delivery Error
Fuel Timing Error
Oxy Sensor Circuit (bank2, Sensor1)
Oxy Sensor Circuit Lo Voltage (bank2, Sensor1)
Oxy Sensor Circuit Hi Voltage (bank2, Sensor1)
Oxy Sensor Circuit Slow Response (bank2, Sensor1)
Oxy Sensor Circuit No Activity Detected (bank2 Sens1)
Heated Oxy Sensor Heater Circuit (bank2, Sensor1)
Oxy Sensor Circuit (bank2, Sensor2)
Oxy Sensor Circuit Lo Voltage (bank2, Sensor2)
Oxy Sensor Circuit Hi Voltage (bank2, Sensor2)
Oxy Sensor Circuit Slow Response (bank2, Sensor2)
Oxy Sensor Circuit No Activity Detected (bank2 Sens2)
Heated Oxy Sensor Heater Circuit (bank2, Sensor2)
Oxy Sensor Circuit (bank2, Sensor 3)
Oxy Sensor Circuit Lo Voltage (bank2, Sensor 3)
Oxy Sensor Circuit Hi Voltage (bank2, Sensor 3)
Oxy Sensor Circuit Slow Response (bank2, Sensor 3)
Oxy Sensor Circuit No Activity Detected (bank2 Sens3)
Heated Oxy Sensor Heater Circuit (bank2, Sensor 3)
Eng Fuel Temp Hi
Incorrect Fuel Composition
Fuel Trim Error (bank1)
Sys too Lean (bank1)
Sys too Rich (bank1)
Fuel Trim Error (bank2)
Sys too Lean (bank2)
Sys too Rich (bank2)
Fuel Composition Sensor Circuit Error
Fuel Composition Sensor Circuit Range/Perf
Fuel Composition Sensor Circuit Lo Input
Fuel Composition Sensor Circuit Hi Input
Fuel Temp Sensor A Circuit Error
Fuel Temp Sensor A Circuit Range/Perf
Fuel Temp Sensor A Circuit Lo Input
Fuel Temp Sensor A Circuit Hi Input
Fuel Temp Sensor A Circuit Intermittent
Fuel Temp Sensor B Circuit Error
Fuel Temp Sensor B Circuit Range/Perf
Fuel Temp Sensor B Circuit Lo Input
Fuel Temp Sensor B Circuit Hi Input
Fuel Temp Sensor B Circuit Intermittent
Fuel Rail Pres Sensor Circuit Error
Fuel Rail Pres Sensor Circuit Range/Perf
Fuel Rail Pres Sensor Circuit Lo Input
Fuel Rail Pres Sensor Circuit Hi Input
Fuel Rail Pres Sensor Circuit Intermittent
Eng Oil Temp Sensor Error
Eng Oil Temp Sensor Range/Perf
Eng Oil Temp Sensor Circuit Lo Input
Eng Oil Temp Sensor Circuit Hi Input
Eng Oil Temp Sensor Intermittent
Injector Circuit Error
Injector Circuit Error - Cylinder 1
Injector Circuit Error - Cylinder 2
Injector Circuit Error - Cylinder 3
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Superchips Inc.
Superchips 2575 MAX Micro Tuner
GM DTC Reader Instructions – Section B
Do not leave the MAX Micro Tuner connected and unattended for any length of time
to prevent unnecessary battery drain.
PLEASE READ THIS ENTIRE INSTRUCTION SHEET BEFORE YOU PROCEED
DTC CODE READER OPERATION
The Superchips Model 2575 MAX Micro Tuner is equipped to function as a Diagnostic
Trouble Code Reader for all GM OBDII equipped vehicles. Using the keypad on the MAX
Micro Tuner, you can read and reset logged DTCs. Using the chart of DTCs that follows, you
can interpret each of the DTCs.
IMPORTANT NOTE
This Superchips 2575 MAX Micro Tuner & DTC Reader is intended for use on GM
vehicles only. Do NOT attempt to use the DTC reader on other than a GM vehicle
as damage to the vehicle PCM or the MAX Micro Tuner may occur that is not
covered by the Superchips, Inc. warranty.
1.
Connecting the Superchips MAX Micro Tuner to Your Vehicle
With the Ignition Switch in the OFF Pos, locate the diagnostic connector under the dash near
the steering wheel or under the glove box and connect the MAX Micro Tuner cable to the
diagnostic connector. (See Figure 2) Turn the ignition switch to the RUN position (See page 3).
Do not start the engine.
When connected, the MAX Micro Tuner will run a self-test.
When the self-test is finished the MAX Micro Tuner will
display the message:
A=Tune Vehicle
B=Diagnostics
2. Selecting Tune Vehicle / Diagnostics
Press ‘B’ to select the DTC Reader Functions. The MAX
Micro Tuner will beep and display the message:
Read the DTCs?
YES or NO
Figure 2
Press ‘NO’ to go directly to the DTC Clearing DTCs at Step 4
Below.
Press ‘YES’ to first read currently stored DTCs.
3.
Reading the DTCs
The MAX Micro Tuner will beep and read the vehicle stored DTCs. If no DTCs have been
logged by the vehicle the MAX Micro Tuner will display the following message:
No DTCs Exist
Press >...
Press the ‘>’ key on the keypad. The MAX Micro Tuner will go back to Select Tune Vehicle /
Diagnostics at Step 2 above.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Superchips Inc.
Page 10 of 20 Form 0127F 02/04/2004
Page 11 of 20 Form 0127F 02/04/2004
If less than 16 DTCs have been logged by the vehicle, the MAX Micro Tuner will display the
following message:
Superchips Inc.
GM 2575 MAX Micro Tuner
Diagnostic Trouble Code Interpretations
DTC # nn – Pxxxx
>= Next B= Done
Please Note
The DTC Reader functions provided as part of the Superchips Micro Tuners are
for convenience purposes only. Industry standard interpretation tables are
supplied Below. Superchips, Inc. makes no warranty of the correctness of the
interpretations. Superchips Customer Service will not provide DTC interpretation
assistance or support.
nn is the DTC sequence.
Pxxxx is the DTC number.
Use the following DTC chart to find the DTC interpretation.
Press the ‘>’ key on the keypad to cycle through the DTCs logged by the vehicle.
Press the ‘B’ key on the keypad when you are finished viewing the logged DTCs.
The MAX Micro Tuner will go to Clearing DTCs at Step 4 Below.
If more than 15 DTCs have been logged by the vehicle, the MAX Micro Tuner will display the
following message:
Too Many DTCs
Press >...
Notes Regarding DTC Interpretation
1.
SAE Code Sections
§
P00xx
Fuel & Air Metering, Auxiliary Emission Controls
§
P01xx
Fuel & Air Metering
§
P02xx
Fuel & Air Metering
§
P03xx
Ignition & Firing Sys
§
P04xx
Auxiliary Emission Controls
§
P05xx
Vehicle Speed, Idle Control & Auxiliary Inputs
§
P06xx
Computer & Auxiliary Outputs
§
P07xx
Transmission
§
P08xx
Transmission
§
P09xx
Transmission
2.
Manufacturer Code Sections
§
P10xx
Fuel & Air Metering, Auxiliary Emission Controls
§
P11xx
Fuel & Air Metering
§
P12xx
Fuel & Air Metering
§
P13xx
Ignition & Firing Sys
§
P14xx
Auxiliary Emission Controls
§
P15xx
Vehicle Speed, Idle Control & Auxiliary Inputs
§
P16xx
Computer & Auxiliary Outputs
§
P17xx
Transmission
§
P18xx
Transmission
§
P19xx
Transmission
3.
All codes are not used in every vehicle model.
4.
P Codes shown with a - symbol may cause a dashboard indicator lamp to light.
5.
Many logged codes are transitory in nature and are automatically reset.
6.
Codes shown Below are for GM vehicles only. Do not attempt to use the MAX Micro
Tuner DTC Reader on other than a GM vehicle as damage to the vehicle PCM or MAX
Micro Tuner may occur that is not covered by the Superchips, Inc. warranty.
7.
DTC P1000 is an indication that the vehicle needs to be driven for a period so that the
vehicle can “learn” certain operating characteristics. This code cannot be cleared using
the DTC Reader clear function.
Press the ‘>’ key on the keypad, the MAX Micro Tuner will go to Clearing DTCs.
4. Clearing the DTCs
The MAX Micro Tuner will beep and display the message:
Clear the DTCs?
YES or NO
Press ‘NO’ to go back to Select Tune Vehicle / Diagnostics at Step 2 above.
Press the ‘YES’ key on the keypad to clear ALL logged DTCs.
The MAX Micro Tuner will beep and display the message:
DTCs Cleared
After clearing all the DTCs, the MAX Micro Tuner will go back to Select Tune Vehicle /
Diagnostics at Step 2 above.
Error Notification
If you need assistance please contact your local dealer/call Superchips Customer
Service at 407-585-7000 M-F 8:00 AM-5:00 PM. EST. Customer Service will not
provide DTC interpretation assistance or support.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 407 585-7000 www.superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement