Advertisement
Advertisement
FCC Warning
The equipment has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with instructions, may cause harmful interference with radio communications. However, there is no guarantee that radio interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to contact the dealer or an experienced Radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
Owner’s Record
The model and warranty numbers are located on the top of the unit. Record the warranty (serial) number in the space provided below. Refer to these numbers whenever you call upon your
Blaupunkt dealer regarding this product.
Warranty Number _____________
Attach Sales Receipt Here
2
Table of Contents
English
FCC Warning .................................................... 2
Owner’s Record ................................................ 2
Features ............................................................ 4
Precautions ....................................................... 4
Detachable Face .............................................. 5
Electrical Connections and Installation ............ 6
Installation ........................................................ 8
Maintenance ................................................... 10
Specifications ................................................. 11
Location of Controls ....................................... 12
Instructions—General Operation ................... 13
Audio Operation .............................................. 14
Radio Operation ............................................. 14
Cassette Player Operation ............................. 16
Auxiliary Input Jack ........................................ 17
Changer Control ............................................. 17
Changer TPM ................................................. 19
Direct Software Control Menu ........................ 20
Wireless Remote Control .............................. 22
Troubleshooting Guide ................................... 23
Français
Avertissement de la FCC ............................... 24
Archive du Propriétaire ................................... 24
Caractéristiques .............................................. 25
Précautions à Prendre .................................... 25
Face Avant Amovible ..................................... 26
Raccordements Électriques et Installation .... 27
Installation ...................................................... 29
Entretien ......................................................... 31
Spécifications ................................................. 32
Emplacements des Commandes ................... 33
Mode d’Emploi/Fonctionnement Général ...... 34
Fonctionnement de la Audio .......................... 35
Fonctionnement de la Radio .......................... 35
Fonctionnement du Lecteur de Cassette ....... 37
Prise Auxiliare ................................................. 38
Commande du Changeur ............................... 39
Mémoire de Programme des plages du
Changeur ................................................ 41
Menu ............................................................... 42
Guide de Dépannage ..................................... 46
Español
Advertencias FCC ........................................ 47
Registro del Propietario ................................ 47
Características .............................................. 48
Precauciones ................................................ 48
Panel Frontal Desmontable (Carátula) ........ 49
Conexiones Eléctricas e Instalación ............ 50
Instalación .................................................... 52
Mantenimiento .............................................. 54
Especificaciones ........................................... 55
Ubicación de los Controles .......................... 56
Instrucciones de Funcionamiento ................ 57
Funcionamiento de Audio ............................ 58
Funcionamiento de la Radio ........................ 59
Funcionamiento del Cassette ...................... 60
Toma de Entrada Auxiliar ............................. 61
Control de Cambiador ................................. 62
Memoria de Programación de Pistas del
Cambiador ........................................... 64
Menu ............................................................. 65
Guía para la Solución de Problemas ........... 69
Portuguese
Aviso da FCC ............................................... 71
Registro do Proprietário ............................... 71
Características .............................................. 72
Precauções ................................................... 72
Painel Removível .......................................... 73
Conexões Eléctricas e Instalação ................ 74
Instalação ..................................................... 76
Manutenção .................................................. 78
Especificações .............................................. 79
Posição dos Controles ................................. 80
Instruções-Funcionamento Geral ................. 81
Funcionamento do Audio ............................. 82
Funcionamento do Rádio ............................. 83
Funcionamento do Toca-Fitas ..................... 84
Tomada para en Trada Auxilier ................... 85
Controle de Cambiador ............................... 86
Memória de Programação de Faixas do
Cambiador ........................................... 88
Menu ............................................................. 89
Guia para Solução de Problemas ................ 93
3
ENGLISH
Features
Congratulations on your purchase of this Blaupunkt Cassette Receiver. Its Codem III-US FM/AM
Tuner and Full-Logic, Soft-Touch Cassette Player provide the ultimate in sound reproduction. Its high-power amplifier and 4-Channel RCA preamp output provide you with tremendous system configuration flexibility. It’s auxiliary input jack lets you easily incorporate portable audio equipment, such as a CD or DAT player, into your car’s sound system.
• Codem III-US Tuner Features:
– Multipath Management
– ASU Electrical Impulse Noise Reduction
– Superior AM Frequency Response
– 18 FM/6 AM Presets, Including 6 FM &
6 AM Travelstore Presets
– Station & Preset Scans
– Station Naming
– Tuner Timer
– Local/Distant Seek & Manual Tuning
• Audio Features:
– 35 Watts x 4 Channel Integrated Amplifier
– Dual-Level Fader
– Over 3 Volts of Distortion-Free Output
4-Channel, Low Impendance (200
Ω
) Preamplifier
– 2-Channel RCA Preamp Output Harness Included
– Bass,Treble, Balance, Fader Controls
– Source Tone & Loudness-Level Memory
– Adjustable Maximum Turn-On Volume & Mute
– Auxiliary Input
• Cassette Player Features:
– Full-Logic Autoreverse Cassette Mechanism
– 9-Track Super CPS Cassette Program Search
– Accelerated Fast-Forward and Rewind
– Radio Monitor with Radio Preset Acess
• Other Features:
– 21 Direct Software Control Menu Options
– Detachable Face with Hardshell Case
– Green Illumination
– Source Display Priority
– Track Up, Down, Scan, Repeat, and Pause
– Adjustable Blank Skip
– Clock/Ignition-Off Clock Recall
– 180 x 50 x 155 mm (7 x 2 x 6 1 /
8
in.)
– Hard Permalloy Tape Head
– Pinch Roller Release
– Dolby B Noise Reduction
– Metal Tape Equalization
DIN/ISO Chassis
– Detachable Wire Harness w/Bullet Connectors
– Snap-In DIN Sleeve & Mounting Hardware
– Side-Bracket Compatible
• CD Changer-Control Features:
– CDC-A05 or CDC-A071 Changer Control
– Disc Naming, Disc Select-by-Name, Disc List
– Disc/Track Up/Down
– Disc/Track Scan, Repeat, Track Mix 1 & 2
• Optional RC-06H or Thummer™ Steering Wheel
Mounted Wireless Remote Control
Your unit’s fully-detachable front faceplate makes the unit useless to would-be thieves.
– Track Program Memory (TPM)
– Cue/Review, Pause/Play
– Last Position Memory
Designed, Engineered and Manufactured by Blaupunkt
Traffic Safety and Precautions
• Do not adjust your unit in difficult driving conditions that demand your full attention.
• As the driver of a motor vehicle, it is your responsibility to pay attention to the traffic situation at all times. Never use your unit in a way that could distract you.
• Always make sure that you are still able to hear any warning signals coming from outside of the vehicle, such as police or fire engine sirens, so that you can react accordingly.
• If your vehicle was parked in direct sunlight resulting in a considerable rise in temperature inside the vehicle, allow the unit to cool off before operating your unit.
• You are cautioned that any changes or modifications not expressly approved in this manual could void your warranty.
• Car Wash precaution - If you have a motorized antenna, make sure to turn off the unit – not just the tuner – so that the antenna is lowered and antenna damage is prevented!
4
Detachable Face
Detaching & Attaching the Face:
The face of this unit can be detached and taken with you to prevent it from being stolen.
Detaching the Face:
Before detaching the face, be sure to press the PWR Button first. Then press the REL (Release)
Button and detach the face by gently pulling it off as illustrated.
Note: Do not pull it straight out from the chassis. Be sure not to drop the face when detaching it from the chassis.
Attaching the Face:
Apply the right hand side of the face to the chassis by sliding (part B) of the face to (part A) at the front of the chassis. Gently push the left side of the face against the front of the chassis until it snaps into place.
Note: Make sure that the face is inserted right side up. Do not press against the display window.
Do not press hard against the face when attaching it to the chassis, it may be easily attached with gentle pressure. When carrying the face with you, put it in the carrying case. Do not expose the face to direct sunlight, heat sources such as hot air ducts or leave it in a humid place. Never leave it on the dash board of a vehicle parked in direct sunlight, where there may be a considerable rise in temperature inside the vehicle.
Affixing Faceplate For Retail Display:
The faceplate can be affixed to the unit’s chassis, which is desirable for a retail display, for example.
To affix the faceplate:
Insert the black bolt into the hole at the left front of the top of the radio. See* below.
S
I
H
G
L
E
N
*
B
A
5
Electrical Connections and Installation
@/<?#&*>@! To avoid the aggravation of costly mistakes and serious damage that could make you feel this way, please carefully read all of the instructions before you begin. Carefully follow all instructions. You’ll be glad you did!
GENERAL RECOMMENDATIONS
• If you’re not confident that you can install the unit correctly, have it installed by a qualified
Blaupunkt installation technician.
• Use this unit only with negative ground 12 Volt (11-16 Volt) direct current (DC).
• Be sure to detach the faceplate before you start to connect or install the unit.
• Don’t assume that a seemingly matching wire harness in the vehicle has leads that match the leads of the unit’s wire harness.
• We recommend making and testing all electrical connections before installing the unit. Connect the leads (wires) according to instructions and diagram below.
ELECTRICAL CONNECTION INSTRUCTIONS
1.
Disconnect the vehicle battery’s negative terminal before making connections.
2.
Connect the speakers and/or external amplifiers (if you have any) following the guidelines in the SPEAKER CONNECTION section below.
3.
Connect the blue (trigger output) lead to an antenna motor trigger switch input terminal (if you have one). (Maximum amperage required must not exceed 150mA.)
4.
If you have an external amplifier, connect the blue/white lead to the amplifier’s trigger switch terminal. DO NOT connect the blue/white lead to the antenna’s power supply input. (Maximum amperage required must not exceed 150mA.)
5.
If you have a cellular telephone set that has a mute lead (lead that supplies constant ground when telephone is in use), connect it to the dark green lead.
6.
Connect the black (power ground) lead to a grounded metal part on the vehicle. We recommend grounding all audio system black ground leads (receiver, external amplifier, etc.) to a common grounding point, preferably a non-painted surface under the instrument panel.
7.
Connect the yellow (constant power) input lead to a source of constant battery power, preferably a terminal to an appropriate slot in the fuse box.
8.
Connect the red (turn-on power) input lead only after the other leads are connected. Be sure to connect the red lead to a positive (+) 12 Volt power terminal that is energized only when the ignition key is set to the on position or accessory position.
9.
Cover the ends of any unused leads with electrical tape. This will prevent them from touching the vehicle or each other and causing a short-circuit and damage to the unit or vehicle.
10. Reconnect the vehicle’s battery.
11. Verify that no fuses have blown.
12. Plug the harness into the unit.
13. Attach the faceplate and test the unit.
Once the connections have been successfully made, you can begin to mount the unit.
SPEAKER CONNECTIONS
The unit’s Dual-Level Fader allows you to fade between the front and the rear channels using either the front and/or rear speaker leads and/or the rear preamp outputs, providing you tremendous flexibility in configuring your speaker arrangement:
• You can connect a speaker (regular, co-axial or tri-axial speakers or component speaker system, all hereafter referred to simply as “speaker”) to each of the units’ four pairs of speaker leads.
• You can connect the 2 RCA preamp outputs to multiple external amplifiers and power multiple speakers or speaker systems through the amplifiers. (Blaupunkt amplifiers and speakers available separately). To add front preamp output, purchase Blaupunkt part 8634494218, which is included in the CDC-A05 and CDC-A071 changers’ harnesses.
• You can use a either or both of these two methods.
6
Connecting the Speaker Leads
To prevent short circuits or serious damage to the unit and/or speakers:
• Connect the speaker leads only as indicated in the wiring diagram. Disconnect the vehicle battery’s negative terminal before making connections.
• Only use speakers that have impedance ratings of 4 ohms or higher and have power-handling capabilities greater than the receiver’s stated power level.
• The unit’s internal amplifier is designed to handle a 4-ohm load on each pair of speaker leads.
• DON’T connect two speakers to a single pair of speaker leads (“in parallel”) unless both speakers each have at least 8 ohms impedance.
• DON’T connect the left and right speaker leads to each other or to the same speakers.
• DON’T connect the front and rear speaker leads to each other or to the same speakers.
• DON’T connect the negative speaker leads to each other.
• DON’T connect the positive speaker leads to each other.
• DON’T connect any active speakers (with built-in amplifiers) to the speaker leads unless their owner’s manuals specifically state that this is O.K.
• Cover the ends of any unused leads with electrical tape. This will prevent them from touching the vehicle or each other and causing a short-circuit and damage to the receiver or vehicle.
Connecting the Pre-Amp Outputs to External Amplifier(s)
To prevent short circuits or serious damage to the receiver, amplifier, and/or speakers:
• Follow the amplifier’s instructions on how to connect the unit’s preamp outputs to the amplifier(s) and connect the speaker(s) directly to the amplifier.
ANTENNA MOTOR
TRIGGER SWITCH
SWITCH
7
Installation
Recommendations
• Carefully choose the mounting location so that the unit won’t interfere with normal driving.
• Avoid mounting locations where the unit would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or where it would subject to dust, dirt or excessive vibration.
• The illustration below shows a typical installation, however, you may need to adjust the installation, depending on the unit. If you have questions or need additional installation hardware, consult your Blaupunkt dealer.
• Make sure the unit is firmly anchored (preferably at both front and back) and does not vibrate.
Mounting Hardware
(1)
Sleeve
(2)
Mounting Strap and Screw
(3)
Release Keys
Mounting The Unit in Most Dashboards
1 Install the Sleeve (1) in the dashboard.
2 Select and bend the appropriate tabs to hold the sleeve firmly in place.
3 A. Attach the Mounting Strap (2) to the underside of the dashboard, using screw.
B. Attach the back of the unit to the mounting strap using the support stem bolt and hardware.
Dashboard
Bend these tabs
8
Mounting the Unit in a Japanese Car
You may have difficulty mounting this unit in some Japanese cars that have ISO mounting features
(side-bracket mounting systems). In this case, consult your Blaupunkt dealer.
1 Run a blade along the slits on the back of the front trim ring and separate it from the unit.
Save the trim ring and related hardware in case you ever in case you ever want to install the unit in another vehicle.
2 Use the vehicle’s own mounting hardware to attach the unit.
1
2
TOYOTA
max. size M5x8
Slit to dashboard/center console max. size
M5x8
Bracket
Support
2
NISSAN
max. size M5x8 to dashboard/center console max. size
M5x8
Bracket
Support
9
Maintenance
Removing the Unit
Use the Release Keys as shown below. Keep them in a safe place in case you need them in the future.
Fuse Replacement
When replacing the fuse, be sure to use one with the correct amperage, which will be stated on the fuse case. Never use a fuse that has a stated amperage exceeding the one supplied for this unit, as this could cause malfunction and serious damage to the unit.
Cleaning the Connectors
The unit may not operate properly if the connectors between the unit and the face are contaminated with dirt. In order to prevent this from happening, remove the face from the unit by pressing the REL
(Release Button), then detach it and clean the connectors from time to time. Clean the connectors with a cotton swab and isoprophyl alcohol (90% or higher). Be sure to clean them with a vertical motion. Never clean them horizontally, because this could damage the contact points.
10
Specifications
Audio Power Specifications
Power Output and Total Harmonic Distortion: 13.5 watts per channel minimum continuous average output into 4 ohms, 4 channels driven, from 30-15,000 Hz with no more than 1% total harmonic distortion.
Other Specifications
Tuner
FM
Tuning Range:
Intermediate Frequency:
FM Mono Sensitivity:
Seek lo sensitivity:
Seek sensitivity
Selectivity:
Signal-to-Noise Ratio:
Harmonic distortion at 1 kHz:
Separation:
Frequency Response:
AM
Tuning Range:
Seek LO (Local) sensitivity
Seek DX (Distant) sensitivity:
Intermediate Frequency:
Signal-to-Noise Ratio:
Frequency Response:
Cassette
Signal-to-Noise Ratio:
Tape Wow and Flutter:
Tape Frequency Response:
Audio
Speaker Impedance:
Maximum Amp Power:
RMS Power:
Bass Control:
Treble Control:
Loud1:
Loud2:
Preamp Outputs:
Preamp Output Voltage:
General
Dimensions (w/o projecting parts/controls):
Mass:
Power Requirement (neg. grnd.):
Operating Temperature:
Supplied Accessories:
Optional Accessories:
87.5 - 107.9 MHz
10.7 MHz
13 dBf
51 dBf
31 dBf
80 dB at 400kHz
65 dB (stereo), 70 dB (mono)
0.7% (stereo), 0.5% (mono)
30 dB
30-15,000 Hz
±
3 dB
530 - 1,710 kHz
50 dB
µ
V
25 dB
µ
V
450 kHz
50 dB
30-5,000 Hz + 3dB
55 dB with Dolby B Noise Reduction
0.10% dB
30-18,000 Hz
±
3 dB
4-8 ohms
4 X 35 Watts (at 4 ohms)
4 X 13.5 Watts (at 4 ohms) <1% THD
±
10 dB @ 100 Hz
±
10 dB @ 10 kHz
+ 8 dB @ 60 Hz & + 2 dB @ 8 kHz
+ 12 dB @ 60Hz & + 4 dB @ 8 khz
4-Channel, Low-Impendance (200
Ω
) Preamplifier
Over 3 Volts of Distortion-Free Preamp Output
180 x 50 x 155 mm
7 x 2 x 6
1
/
8
in.
Approx. 1.4 kg (3.0 lb.)
12 V DC car battery (11-16 V DC allowable)
15
°
F to 120
°
F, –10
°
C to 50
°
C
• Unit
• Faceplate
• Wire Harness, including 2-Channel RCA Preamp Output
Harness
• DIN Sleeve
• Mounting Hardware
• Owner’s Manual in English, French, Spanish and Portuguese
•
RC-06H Wireless Remote Control
• CDC-A05 or A071 CD Changer
• 4-Channel Preamp Output Harness-Part No. 8634494218
• Thummer™ Steering Wheel Mounted Wireless Remote
11
Location of Controls
1.
REL (Release) Button
2.
Mute/Audio Button
Mute, Bass, Treble, Balance/Fade Access
Name Storing/Deletion/Exit
Minute: 00
3.
Lens Receiving for Wireless Remote Controls
4.
SCA (Scan) Button
Station Scan,Preset Scan,Track Scan,Disc Scan
5.
DIS (Display)/MENU Button
Display Change
Menu Access
Demo Message Off/On (8 second press)
6.
Cassette Insertion Slot
7.
Cassette Program (Direction) Change
8.
Dolby B Noise Reduction
9.
Eject
10. Metal Tape Equalization
11. SRC (Source)/LIST Button
Source Change
Disc Name List Access
12. Volume +
13. Volume –
14. PWR (Power) Button
15. <<
Manual Tuning Down
Menu Feature Adjust
Fast Rewind
Changer Track Up
Review
List Mode Disc Select
Balance To Left
Name Character Position
16. >>
Manual Tuning Up
Menu Feature Adjust
Fast Forward
Changer Track Down
Cue
List Mode Disc Select
Balance to Right
Name Character Position
17. /\
Seek Tuning Up
Menu Feature Select
Cassette Program Search Up
Changer Disc Up
Bass, Treble Increase
Fade to Front
Name Character Select
18. V Button
Manual Tuning Down
Menu Feature Adjust
Cassette Program Search Down
Changer Disc Down
Bass, Treble Decrease
Fade to Rear
Name Character Select
19. Display
20. RPT (Repeat) Track Repeat & Disc Repeat
21. FM/FMT Button
FM Band Access, FM Travel Store
22. MIX Button (MIX 1 and 2)
23. AM/AMT Button
AM Band Access, AM Travel Store
24. Pause Button
25. LD (Loud)/SENS Button
Loudness On/Off
26. FM/AM Preset Buttons
27. TPM (Track Program Memory) Button
TPM Store, TPM Play, TPM Delete
12
Instructions — General Operation
See Traffic Safety & Precautions on page 4.
“Press” means a momentary press of less than 1/2 second. All presses requiring more than 1/2 second are followed by beep. (Beep for all button presses available through Direct Software
Control Menu.)
“Time Out” When additional button presses are anticipated to complete a procedure, the unit will automatically exit the procedure after 4 seconds of inactivity. (8 for Menu mode.)
Ignition-Off Clock Recall
Any button press while ignition off displays time for 8 seconds.
Ignition-On
Unit lights up and clock is displayed.
Demo Mode
The unit is programmed to scroll some key features across the display if no button is presses for one minute . (You may have seen this at the store where you purchased your radio.) TO TURN THIS OFF, turn the unit on and press DIS for 8 seconds until “DEMO OFF” appears. (Pressing DIS for 8 seconds again will re-activate this feature.)
Release for Detachable Faceplate
Push REL to detach face. Already-inserted cassette remains in unit. Current settings and source mode are stored, except when detach occurs during Menu mode, new Menu settings are not stored. If power was not switched off before face removed, unit will automatically power-on when face is reattached.
Power (PWR) On
When ignition on, press PWR or insert a tape to turn unit on. Last-used source becomes active, unless unit is turned on by inserting cassette, in which case cassette player becomes active.
Display sequence at Power-On:
1. Turn-On Message (To turn message off or modify message, see Menu, page 20.)
2. “RADIO”,“TAPE”, CHANGER”, or “AUX IN”.
3. Functional information sequence (See Display Options, below.)
4. Priority display for active source.
Display Options
Press DIS to change information shown at times when no manual or automatic activity takes place.
Choice of priority display is separate for each audio source:
Radio: Station Name (if named) —> Frequency —> Clock
Cassette: “TAPE” (1 or 2) –> Clock
CDC:
AUX :
Disc Name (if named) or Disc No.–>Disc No./Track No.–>Track No./Elapsed Play
Time–>Clock
“AUX IN” —> Clock
After a change in source, radio station or changer discs, the current source’s non-clock displays are shown in sequence, then display returns to current source’s priority display.
Source (SRC)
Use SRC to select source - radio or cassette (if already inserted,) CD Changer (if connected) and/ or auxiliary input (even if no input on aux in line) as per model’s features.
Power Off
Press PWR for more than 1/2 second to turn unit off. Unit stores current settings for source, station or track, etc. Antenna and amplifier trigger wires shut off voltage. (If faceplate still attached, display switches to clock.)
13
Audio Operation
Volume Control Buttons (+/–)
Press + and - to increase/decrease volume from 0 to 63, in increments of 1.25 dB/step. Volume control is accessible from all modes except Name Access and Edit modes.
Mute & Cellular Mute
Press Mute to temporarily reduce volume to level set under Menu. “MUTE” appears. (Same mute level is also activated by cellular mute (if connected). “TEL MUTE” appears.) Mute or cellular mute is terminated by pressing any button. (Cellular mute is also ended by ending cellular telephone use.) If volume level lower than mute level, lower volume level is maintained, even though “MUTE” appears.
Automatic Source Tone Memory
Bass and treble adjustments made are source specific, allowing different settings for each source
(FM, AM, Cassette, Auxiliary and/or Changer), as is loudness.
Bass, Treble, Balance and Fade
Press Mute/AUDIO for more than 1/2 second to access Bass. Subsequent presses access Treble mode, then Balance/Fader mode.
Bass -Adjust from +7 to -7 at 2 dB/step using >> or /\ to increase bass, << or V to decrease.
Treble - Adjust from +7 to -7 at 2 dB/step using >> or /\ to increase treble, << or V to decrease.
Balance/Fade (“BAL/FADE”) Adjust balance from L9 (all the way left) using << to R9 (all the way right) using >>. Adjust fader from F9 (sound only from the front) using /\ to R9 (sound only from the rear) using V.
Loudness (LD)
Press LD to increase sound of low and high frequencies. Loudness level set under Menu and is source dependent. LD icon appears. To cancel, press LD again.
Radio Operation
Once tuning is complete, radio display sequence follows.
Last Station Memory
Each FM bank and AM band has its own last station memory which holds last-tuned frequency for that band or bank irrespective of whether that frequency is stored into a preset.
14
FM and AM Buttons
Press FM to access last active FM bank. When in FM radio mode, press of FM advances to next
FM band, FM1, FM2, or FM3/FMT. When in AM mode or other source, pressing FM button returns to last-tuned FM band. Press AM to access AM/AMT Band.
Seek Tuning
Press /\ or V to seek next receivable frequency. Tuning stops at frequency that fulfills sensitivity requirements predetermined by sensitivity set through SENS/LD button. Press of /\ or V buttons for more than 1/2 second seeks next receivable frequency after button is released.
Tuning Sensitivity (SENS)
Press SENS/LD for more that 2 seconds to switch between LO (Local) and DX (Distant) search sensitivity
Radio Reception Hints
• When listening to weak or distant AM stations, adjusting the Treble to minimum (-7) will reduce
noise and improve sound.
• In general, set SENS to DX if in rural areas or where stations tend to be weak and distant, and to
LO when in metropolitan areas or where stations tend to be strong and local.
Stereo Symbol
Stereo symbol turns on if a stereo station with an incoming signal of 20 dB
µ
V is received. The unit gradually switches between mono to stereo automatically.
Manual Tuning
Press << or >> and frequency will go one channel/step in direction pressed. Press and hold causes continuous manual tuning.
Preset Station Storage
After tuning desired frequency on desired band, press and hold a Preset Button for more than 2 seconds to store current frequency. Audio is muted during storage, preset number appears, and beep acknowledges storage. No preset storage during seek, scan or Travel Store.
Preset Station Selection
Press desired Preset Button.
Travel Store
This feature allows you to automatically store stations onto all 6 preset buttons and is especially useful when traveling outside your normal listening area. In any FM Bank, press FM Button for 2 seconds to activate FM Travel Store. (In AM Bank, press AM Button for 2 seconds to activate AM
Travel Store.) T STORE appears, followed by seek-type display of frequency and preset numbers.
Beginning at the bottom of the band, TS stores six strongest stations, one on each of the six preset buttons, in decreasing order of signal strength, and returns to preset 1. Pressing any presets FM, or AM Button scan cancels search operation. When source is changed during Travel Store, operation completes itself, despite source change.
Station Scan Tuning
Press SCA. “STA SCAN” appears, then frequency blinks (along with preset number if appropriate) during scanning. Unit stops at receivable stations for scan time set under Menu. Unit continuously scans until user stops scan by pressing SCA, another tuning button, SRC, or MENU button.
Preset Scan Tuning
Press PS/SCA for more than 2 seconds. “PS SCAN” appears, then frequency and preset number blink during scanning. Unit starts at FM1/Preset 1 (or AM/Preset 1) and proceeds through all presets (in FM all three banks) and returns to frequency tuned prior to PS activation and stops.
Stops earlier if user presses another tuning button, SCA, SRC, or MENU button. Unit skips past preset frequencies that do not meet minimal seek-tuning threshold.
Tuner Timer and Station Naming (See pages 20 and 21)
15
Cassette Tape Player Operation
Once playback location change is complete, tape display sequence follows.
Cassette Insertion & Eject
“LOADING” appears upon insert and cassette play follows. Press Eject for a motorized eject.
“EJECT” appears and radio plays. The following indicates what happens with insert and eject under various conditions:
Activity Ignition off Ignition On/
Unit Off
Ignition On/
Power On/
Non-Tape Source
Insert
Eject
No Reaction
OK
Turns Unit On
OK
Tape becomes active source
OK
Cassette Direction/Program Selection
∆ ∆
“TAPE 1” indicates top side of tape is in play; “TAPE 2”, bottom side. Press to reverse tape direction during playback. Tape automatically changes direction at end of tape.
Cassette Fast Wind
Press << to activate fast rewind (“FAST REW”) or >> to activate fast forward, (“FAST FWD”).
To stop FF, press /\, V, << or >> buttons. To stop FR, press /\, V, << or >>.
Super-Cassette Program Search
Press /\ or V once for each track you wish to advance or go back. Display will blink SEARCH plus the number of tracks, e.g. “SEARCH 4” or “SEARCH-4”. If V is pressed more times than current track value, tape will fast-rewind and begin play at first track. If /\ is pressed more times than there are tracks, tape will advance to end of tape, autoreverse and begin play. To stop CPS up function, press << or >> or V. To stop CPS down, press << or >> or /\.
Radio Monitor
Radio can be heard during tape winding modes (FF, FR, Tape Scan, Track Repeat, Cassette
Program Search and Blank Skip). When activated (through Menu), RM icon appears during cassette play. Preset stations on last-heard band available during tape winding.
16
Tape Track Repeat
To play currently-selected track repeatedly, press RPT. While automatically rewinding to beginning of track, “FAST REW” appears. To cancel, press again. If tape manually advanced, RPTI remains active for new track.
Tape Scan
Press SCA to start. “TRCKSCAN” blinks during scanning operation. Unit stops at each track for scan time set under Menu. If radio monitor feature is activated, the radio monitor is heard while advancing to next track, and preset frequencies for most recently heard band are available. At end of tape, unit reverses and continues to scan new side. Unit continuously scans until SCA, SRC, FM,
AM , EJECT, or MENU is pressed.
Pause
To pause, press II . To cancel, press again or press a playback-related button.
Pinch Roller Release
During tape pause, or during change to another source, or during power off, unit’s pinch feature automatically activates, protecting tape and tape head.
Blank Skip - See page 21.
Dolby B Noise Reduction
Press Dolby button when playing tapes recorded with the Dolby B noise reduction system to eliminate hissing noise. The Dolby symbol appears in the display. To cancel, press again.
Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
Metal and CR02 Tapes
During tape mode (but not RM mode), press MTL to activate or deactivate MTL.
Auxiliary Input Jack
Connect other audio equipment, such as a portable CD or DAT player, through the 500 mV/3.5
mm pigtail connector. Access auxiliary equipment output by pressing SRC until “AUX IN” appears.
Adjust volume, bass, and treble settings through receiver.
Changer Control
(When optional CD changer is connected.)
Your radio is ready to control a Blaupunkt CD Changer with the DISC Management System, such as the CDC-A05 or CDC-A071. See your Blaupunkt dealer for more information.
Once changer playback adjustment is complete, CD Changer display sequence follows.
Track Up/Down
Press << and >> to select tracks. Disc No. and Track No. appear. Pressing << will restart current track if less more than 1 second of track has been played. If less than 1 second has been played, unit goes to beginning of previous track. Pressing >> in last track will select next disc.
Track Cue and Review
Press and hold >> or << for audible cue or review.
Naming Discs- See page 22
Disc Select By Name (Disc Up/Down)
Press /\ / V controls to select discs. For easy identification of discs, the disc name appears immediately (or disc number if disc not named and identified since magazine was inserted. See
Disc Name Table, below.)
17
Disc Name List
Allows you to scroll through names of discs in changer without leaving currently-playing disc.
1.
Press SRC for more than 1/2 second to enter LIST mode. Small “L” appears in left-most position of display.
2.
Use /\ and V to scroll though names. (Disc number appears if disc has not been named and identified since magazine was inserted. See Disc Name Table, below.)
3.
If you find name of a disc that you want to hear, press < or > and changer automatically goes to that disc. If no new disc is selected, the LIST mode automatically ends after 5 seconds.
Disc Name Table
Until the changer has the chance to identify the discs in a newly-inserted magazine, the names of any named discs are not available. When a new magazine is inserted, the changer reads and identifies the discs’ names at the earliest of the following opportunities: Disc Select (automatic or manual), Disc Scan, or Disc Select during Disc Naming mode. Or, if you switch to another source before the discs have been read, the changer automatically reads and identifies the names of the unread discs in a background scan that lasts at most about 2 minutes, making the names readily available as soon as possible!
Track Repeat
To play current track repeatedly, press RPT as needed until RPTI appears. If track manually advanced, RPTI remains active for new track.
Disc Repeat
To play current disc repeatedly, press RPT as needed until RPTII appears. Once all tracks on disc are played, disc is repeated. If disc manually advanced, RPTII remains active for new disc.
To cancel RPT feature, press as needed until RPT indicator disappears.
Track Mix
Press MIX as needed until MIXI icon appears. This also cancels repeat, scan, and TPM features, if previously active. A track will not be played a second time until all tracks have been played. Once all tracks have been played, next disc is selected.
Disc Mix
Press MIX as needed until MIXII appears. MIXII behaves per software in CD changer. Press of /\ /
V during MIXII mode returns unit to regular play. To cancel MIXII, press as needed until MIX indicator disappears.
Permissible combinations of MIX and RPT
Press of MIX during RPTII mixes all of tracks within one disc continuously.
Pause
To pause, press ll . To resume playback, press again or press other playback button.
Track Scan
Press SCA to start Track Scan. “TRCKSCAN” appears, then Track No. and Elapsed Play Time blink during scanning operation. Unit stops at each track for scan time set under Menu. After
18
scanning all tracks on disc, unit advances to next disc. Unit continuously scans until user stops scan by pressing a source control, SCA or MENU. SCA deactivates any MIX or RPT modes.
Disc Scan
Press SCA for more than 2 seconds to start Disc Scan. “DISCSCAN” appears, then Disc Names (or if unnamed, Disc Nos.) blink during scanning operation. Unit stops at each disc as per CD scan time set under Menu. Unit continuously scans until user stops scan by pressing a source control,
SCA or MENU. Disc Scan also deactivates any active previously-active MIX or RPT modes.
Changer Reset
In unlikely case of CD changer trouble, reset CD changer by turning unit’s power and/or ignition off, and then power on unit. (See TROUBLESHOOTING on page 23.)
Changer Track Program Memory
(Skip/Play/Memory)
Allows you to play only those tracks you want to hear.
Programming a Disc
1. In CD changer mode, select CD disc you want to program.
2. During regular (non-TPM) play only, select track to be added to program.
3. Press and hold TPM for more than 2 seconds. “TPMSTORE” appears. The plus symbol (+) will appear in left-most character position of name display. This indicates the disc is programmed.
4. Select next selection to be programmed, using << and >> buttons. Repeat step 3 as desired.
5. Select other discs as desired using /\ / V controls and repeat steps 2-4 to program other discs.
Running Track Program
Press TPM to activate program. TPM appears. (If TPM pressed when no programming has been entered for discs currently in magazine, “NO PROG” appears.)
TPM Track Up/Down
To advance and go back within program, use << and >> buttons. (To access tracks that are skipped, you must exit TPM play mode.) Note: Pressing MIX or RPT within TPM play ends TPM play mode and starts MIX or RPT modes.
TPM Disc Up/Down
Press of /\ or V during TPM play advances to next disc that has been programmed.
TPM Scan
Press TPM to start TPM play. Press SCA. Track No. and Elapsed Play Time blink during scanning operation. Programmed tracks will be scanned in order starting with first programmed track.
Press SCA to end scan and listen to desired track.
Clearing Track Programming
To delete a single track:
1. First, press TPM to start TPM play.
2. Select track you want to delete from program
3. Press and hold TPM Button. Beep sounds after 2 seconds. When button released between 2 and 4 seconds “TPMCLEAR” appears and one track is deleted from program.
To delete ALL tracks from ONE Disc:
1. First, press TPM to start TPM play.
2. Select DISC you want to delete from program.
3. Press and hold TPM Button. Beep sounds at 2 seconds and 4 seconds. When button released between 4 and 8 seconds, “TPMCLEAR” appears and all tracks on that disc are deleted from program. When name re-appears, ”+” programming symbol will no longer appear.
To delete ALL Track Programming from ALL Discs WHETHER OR NOT IN MAGAZINE:
1. First, press TPM to start TPM play.
2. Press and hold TPM Button. Beep sounds at 2 seconds, 4 seconds, and 8 seconds. When released after 8 seconds, “TPMCLEAR” appears and ALL programming on ALL discs is
19
deleted. When name reappears “+” programming symbol will no longer appear.
Direct Software Control Menu
Blaupunkt’s exclusive Direct Software Control Menu has many unique features that allow you to customize the unit to your needs and preferences. All Menu options (except timer and naming options) are available regardless of which source is in use: AM, FM, Cassette, Changer, Auxiliary.
Using the Menu (See Traffic Safety & Precautions on page 4)
1.
Press DIS/MENU for 2 seconds to enter Menu mode.
2.
Press /\ / V controls to scroll through Menu.
3.
Use << or >> to change Menu setting (or to enter the following modes: Turn-on Message,
Clock Adjustment, Timer Set, Station Name Access/Edit and Disc Name Access/Edit.)
4.
Exiting Menu: Press of DIS (or after 8 seconds), unit exits from Menu. Changes are stored upon manual or automatic time-out of Menu or turn-off by PWR button — but not stored if exit caused by panel release or ignition off.
Turn-On Message Activation (“MSG ON”/”MSG OFF”)
Press << or >> to turn message on or off.
Turn-On Message Programming (“MSG ENTR”)
The unit can scroll a 40-character message across the display at the time of turn-on. To create your own message:
1.
Press >> button. Eight characters appear with the first one blinking.
2.
Press /\ / V to select desired characters. If you want to put a blank space in name, select “__”.
3.
Press << or >> to locate next character.
4.
After eighth character (the farthest right character) is completed, first (left-most) character of next group of eight characters begins to flash. After fifth group of eight characters, pressing >> will access first group again.
5.
Press Mute to store turn-on message and return to Menu.
Clock Adjustment (“CLOCKSET”)
Pressing << or >> shows blinking time. Subsequent press of << advances the hour; >> advances the minutes. (To change minute indicator to nearest hour (:00), press Mute button). Unit begins keeping the time when /\ or V is pressed or when Menu mode ends.)
Tuner Timer Set Mode (“TMR SET”)
1.
Before entering Menu, tune in the radio frequency to be activated by timer.
2.
Enter Menu mode and scroll to “TMR SET” by pressing /\ or V.
3.
Press << or >> to enter timer adjustment mode.
4.
Select time that unit should switch to this station by pressing << to adjust hours, >> to adjust minutes. Press Mute to adjust minutes to :00.
5.
To store station and time, press /\ / V or DIS.
Tuner Timer On/Off (“TMR ON”/“TMR OFF”)
Tuner timer allows unit to go to a certain frequency at a certain time — from any source. When
20
ignition on and unit off, the timer even turns the unit on and goes to the specified frequency. Press
<< or >> to turn Tuner Timer on or off.
Radio Monitor (“RM ON” & RM OFF”)
Allows radio to play during tape winding or scan. If this feature has been activated, RM icon appears when tape is in use.
Blank Skip Time (“BSKPTIME”)
When unit reaches a blank section of tape, it can automatically fast-forward to next recorded section. Use << and >> to choose minimum amount of blank time before blank skip begins from between 1 to 16 seconds. SUGGESTION: Classical music listeners may want to specify a longer blank, so that the unit doesn’t mistake soft passages for blank spots.
Blank Skip Activation
Press << or >> to turn Blankskip on or off.
Scan Times
You can set different scan times for Radio (“RD SCNTM”), Cassette (“TP SCNTM”), and Changer
(“CD SCNTM”) between 1 and 16 seconds. Press << or >> to adjust scan time.
Confirmation Beep On/Off (“BTTNBEEP”)
To activate or defeat beep for all button presses, press << or >>. (Button presses requiring more than 1/2 second always have confirmation beep.)
Adjustable Mute Level (“MUTE LVL”)
The unit’s mute level can be adjusted to any volume level. This mute level also applies to cellular mute. During Menu mode, once “MUTE LVL” appears, actual mute level is heard. Adjust the mute level volume by using <</>>, NOT + and –. (If mute is activated when unit volume level is lower than mute level, unit volume level is maintained, even though “MUTE” appears.
Maximum Turn-On Volume Level (“MAXONVOL”)
Sets maximum volume that is heard when unit is turned on. (Once “MAXONVOL” appears, actual
MAXONVOL level is heard.) Adjust the MAXONVOL volume by using <</>>, NOT + and –. If unit is turned off while volume is louder than MAXONVOL, turn-on volume will be at MAXONVOL level.
However, if unit is turned off when volume level is lower than MAXONVOL, turn-on volume will be at level it was when unit was turned off.
Loudness Levels
You can choose between two loudness settings for each audio source: “LOUD TAPE”, “LOUD
AUX”, “LOUD CD”, (for CD Changer) “LOUD AM” and “LOUD FM”. “LOUD 1” provides up to 8 dB boost in bass (centered at 60 Hz) and up to a 2 dB boost in treble (centered at 8 KHz). “LOUD 2” provides up to 12 dB boost in bass (centered at 60 Hz) and up to a 4 dB boost in treble (centered at
8 KHz). To set the loudness level for each source, use << and >>.
Radio Station Naming (“STN NAME”)
Available only while radio is active source. One name per frequency, 8 characters per name.
(Names can be assigned to any frequency, preset or not.) If you try to enter more than 30 names,
“**FULL**” appears. You can then enter new names after erasing some of existing names.
To store station names:
5.
6.
7.
8.
1.
2.
3.
4.
Press DIS for more than 2 seconds to enter Menu mode.
Scroll to Radio Station Naming feature by pressing /\ / V .
Enter Station Name Access mode by pressing << or >> button.
Tune to desired station using AM, FM, presets or /\ / V buttons. If previously named, name appears.
Press << or >> buttons to enter Station Name Edit mode.
Press /\ / V to select character. Select “__“ for a blank space.
Press << or >> buttons to select next character position.
Press Mute to store name. Display blinks STORING twice before return to Station Access mode.
9.
To name another station, repeat steps 4-8.
10.
To return to Menu, press Mute again.
(There is no time-out from Station Name Access & Edit modes.)
Display Priority & Radio Station Names- See Display Options on page 13.
21
Changing a Radio Station Name
Repeat steps 1 to 10 in Radio Station Naming, changing only those characters that you wish to change.
Erasing ONE Radio Station Name
Access Station Access mode (See Radio Station Naming, above.) Choose station with name to be deleted. When name appears, press Mute for 2 seconds. Beep sounds. Release now to delete this name. “NAME” and “DELETED” blink alternately.
Erasing ALL Radio Station Names
Access Station Access mode under Menu. When a name appears, press Mute for 8 seconds.
“ALLNAMES” appears for 2 seconds, then “DELETED” until deletion completed.
Disc Naming (“DISCNAME”)
Assigning a name to a disc makes it much easier to locate the desired disc. You can enter and store names of up to 99 discs (one name per disc, maximum of 7 characters per name). If you try to enter more than 99 names, ***FULL*** indication will appear. You can then enter new names after erasing some of existing names.
To name a disc:
1.
2.
3.
Press DIS for more than 2 seconds to enter the Menu mode.
Scroll to Disc Naming function by pressing /\ / V
Enter Disc Access mode by pressing << or >> button.
4.
5.
6.
7.
Select desired disc using the /\ / V buttons. If previously named, name appears.
Press << or >> to enter Disc Name Edit Mode.
Press /\ / V to select characters. Select “_” for a blank space.
Press << or >> buttons to select next character position.
8.
9.
Press Mute to store name. Display blinks “STORING” twice. Unit returns to Disc Access mode.
To name another disc, repeat steps 4-8.
10.
Press Mute to return to Menu.
(There is no time-out from Disc Name Access & Edit modes.)
Display Priority & Disc Names: (See Display Options on page 13.)
Changing a Disc Name
Repeat steps 1 to 10 in Disc Naming, changing only those characters that you wish to change.
Erasing One Disc Name
Access Disc Access mode under Menu (See Disc Naming). Choose disc that has name to be deleted. When name appears, press Mute for 2 seconds. Beep sounds. Release now to delete the name. “NAME” and “DELETED” alternately blink.
Erasing ALL Disc Names
Warning: THIS FEATURE ERASES ALL NAMES AND ASSOCIATED TRACK PROGRAM
MEMORY FOR ALL DISCS, INCLUDING DISCS NOT PRESENTLY IN MAGAZINE.
Access Disc Access mode under Menu. (See Disc Naming.) When a name appears, press Mute for 8 seconds. “ALLNAMES” appears for 2 seconds, then “DELETED” until deletion completed.
22
Wireless Remote Control
For added convenience you can control key features of your Blaupunkt 5 Series Receiver with either of two Blaupunkt wireless remote controls, the RC-06H (included with the Aspen CM147) or the Thummer™.
The unique Thummer mounts to the inside of the steering wheel rim and allows you to control the receiver without taking your hand off the steering wheel. The RC-06H is a credit card-sized remote control. To receive wireless commands, your receiver is equipped with a built-in infrared sensor (or “eye”) on the faceplate.
Both of remote controls have the following buttons: SRC, SCA, +/- /\, V, << and >>. You can use them to activate all of the same features as you would using the corresponding buttons on front of the unit itself.
See your Blaupunkt dealer for details.
23
Troubleshooting Guide
The following check will assist in the correction of most problems which you may encounter with your unit. Before going through the check list below, refer back to the connection and operating procedures.
General
Trouble
No sound.
Cause/Solution
• Adjust the volume with the + button.
• With a two-speaker system set the fader control to the center position.
Indications do not appear on the display window.
• Remove the front panel and clean the connectors. See
“Cleaning the Connectors’’ of “Maintenance’’ for details.
Radio reception
Trouble
Preset stations are not receivable.
Automatic tuning is not possible.
Travel Store feature does not complete storing of six stations.
Cause/Solution
• The broadcast is too weak.
• The broadcast is too weak. —> Use manual tuning.
• Not enough broadcast frequencies are receivable.
* Also make sure that antenna is connected, extended and dry inside.
CD Changer operation
Trouble
CD play does not start.
Cause/Solution
• Dusty or defective disc.
• The ambient temperature is more than 50
°
C (120
°
F).
• The disc is inserted with the printed side downwards.
The disc cannot be loaded or is automatically ejected.
The sound skips due to vibration.
• The changer is installed at an angle of more than 20
°
.
• The changer is not installed on the sturdy part of a car.
• Dusty or defective disc.
Error Displays
Display Cause Solution
“CD ERROR” A disc problem such as an upside Insert the disc correctly.
down or dirty disc, or a CD-ROM Clean the disc.
(computer) disc.
“NO DISC” No magazine or disc in changer Take out the magazine and insert the discs.
If the above mentioned solutions do not help to improve the situation, consult your nearest Blaupunkt dealer or in the United States call 1-800-266-2528.
24
German Headquarters:
Blaupunkt-Werke GmbH
Postfach 77 77 77
D-31132 Hildesheim
Germany
Robert Bosch Corporation
Sales Group — Blaupunkt Division
2800 South 25th Avenue, Broadview, Illinois 60153
1-800-950-BLAU
Robert Bosch, SA., DE, C. V.
Dr. Lucio 270
Cols. Doctores, Mexico 06720
Made in Malaysia
Fabrique en Malasie
Hecho en Malasia
Fabricado en Malaysia
Copyright 1997 by the Robert Bosch Corporation
No portion of this work may be reproduced in any form without the written consent of the Robert Bosch Corporation.
25
Notes / Notas
26
Advertisement