Smart Grid Solutions Guide (Rev. N)

Smart Grid Solutions Guide (Rev. N)
Smart Grid Solutions
For Power Infrastructure & Industrial Energy Systems
•Grid Infrastructure
•Smart Meters for Electricity, Gas, Water and Heat
•Smart Energy Management for Homes and Buildings
•Wired and Wireless Communication
www.ti.com/smartgrid2014
Smart Grid Solutions Guide
Introduction
Table of Contents
Engineering a Smarter Grid
2-3
Engineering a Smarter Grid
Dedicated Silicon + Optimized Software + Global
Support = The Power of TI
Today’s solutions for tomorrow’s power infrastructure
and industrial energy systems
• Grid Infrastructure
• Smart Meters for Electricity, Gas, Water and Heat
• Smart Energy Management for Homes and Buildings
• Wired and Wireless Communication
Smart Grid Infrastructure
With millions of energy-meter ICs shipped over the past
decade, Texas Instruments is the global systems provider
for innovative, secure, economical and future-proof
semiconductor solutions for the worldwide smart grid.
TI offers the industry’s broadest smart grid portfolio of
metrology expertise, application ­processors, communication
systems and analog components in readily ­available
silicon. Advanced software, tools and support are also
available to meet the needs of the world’s smart energy grid.
6
7
4-5
Data Concentrator Solutions
Power Line Communications (PLC)
5
System Block Diagram and Recommended Products
Smart Electricity Meter
Recommended Products
System Block Diagram and Recommended Products
Flow Meter
8-9
9
Smart Gas/Water/Heat/Heat Cost Allocator
Wireless M-Bus Solutions
Smart Energy Management for Homes and Buildings
10
11
System Solutions
Recommended Products
Wireless Connectivity
11
Sub-1 GHz, ZigBee®, 6LoWPAN, wM-Bus
and Wi-Fi® Solutions
Signal Chain and Power Management
12
13
Analog Products
Power Management Products
Development Tools
14-17 Smart Grid Development Tools
2
|
Smart Grid Solutions Guide 2014
www.ti.com/smartgrid
Texas Instruments
Engineering a Smarter Grid
Dedicated Silicon + Optimized Software + Global Support = The Power of TI
Across the smart grid application spectrum, TI supports every stage of the design process, from device selection
and software development to tools and system solutions.
Electric Meter Metrology
Solutions that meet ANSI C12.20 and IEC
62053 standards, Class 0.2 and 0.5:
• Single-phase System on Chip (SoC):
MSP430F673x and MSP430AFE2xx
• Three-phase SoC: MSP430F677x
• Dedicated analog front ends: ADS13xx
Flow Meter Metrology
Dedicated Automatic Meter Reading (AMR)
solutions for increased accuracy and
ultra-low-power performance:
• Water/heat meter MCU (with Scan IF):
MSP430FW42x
Applications Processors
Industry standard microcontrollers and
microprocessors:
• Tiva™ C Series ARM® Cortex™-M4
microcontrollers: TM4C123x – 80 MHz,
up to 256KB flash
• Sitara™ processors: AM335x with
Cortex-A8 core, up to 1 GHz
• Powerful SoC DSP + ARM
• MSP430™ Microcontrollers:
MSP430F5xx/6xx – ultra-low-power,
up to 512KB
Power Line Communications (PLC)
Complete, certified and field-tested PLC
modems for all narrowband PLC
standards:
• PRIME, G3, IEEE-P1901.2, ITU G.9903
• TI PLC reference designs for both meter
end points and data concentrators
• CC3000: SimpleLink™ Wi-Fi®
module solution is self-contained and
integrates total Wi-Fi connectivity,
including Wi-Fi access point
• WiLink™ 8 solutions are highly
integrated and support Wi-Fi,
Bluetooth® on a single chip.
• Bluetooth/Bluetooth low energy:
CC256x dual-mode controller, CC254x
Bluetooth low energy devices.
TI wireless semiconductors are
complemented by protocol stacks and
application profiles supported by TI,
including ZigBee PRO and ZigBee/IP,
Smart Energy Profile, Wireless M-BUS
and 6LoWPAN.
Prepayment Systems
RFID technology supporting ISO
14443A/B, ISO 15693, MIFARE™
and Near-Field Communi­­cations (NFC)
provides complete silicon and software
stack solutions:
• TRF7970A transceiver
• RF430CL NFC smart interface tag
Power Management
TI provides optimized power-management
solutions for all smart grid applications
(including offline, isolated AC/DC to
non-isolated DC/DC) with the widest
range of integration and performance
options available.
See Power tables for AC/DC, DC/DC,
LDO, PMIC and more on page 13.
Wireless Connectivity
Development Tools
TI produces the best performing RF
solutions for wide-area and home-area
networks:
• CC112x: Narrowband transceivers
in the ISM band, down to 6.25-kHz
channels
• CC12xx: Broadband transceivers in the
ISM band, data rates up to 1 Mbps
• CC2538: SoC for ZigBee®, Smart
Energy with ARM Cortex-M3
Robust and fully tested solutions with
one-to-many approach—Industry-leading
smart-meter board for development,
ZigBee and power line communication
large-node network test—and more.
Quality
TI meets high-volume, high-quality
requirements with expertise in
manufacturing.
People
TI provides dedicated application teams
for hardware and software that support
complete analog and digital system
­solutions in grid infrastructure, metrology,
PLC and RF connectivity.
External Representation
TI maintains an active presence in global
regulatory bodies, including:
• Bluetooth SIG
• ETSI
• EcoNet Consortium
• Euridis
• EU-US Smart Grid Coordination Group
• G3-PLC Alliance
• IEEE 802.15.4/IEEE 802.15.4g Smart
Utility Network (SUN) wireless standard
• Home Plug Alliance
• IEEE P1901.2 narrowband PLC
standard
• IPSO Alliance (6LoWPAN)
• ISO/IEC JWG CI (PEV)
• ITU-T Focus Group on Smart Grid
• ITU-T G.9901, G.9902, G.9903, G.9904
narrowband PLC standard
• KNX Alliance
• PRIME Alliance
• SAE PHEV Committee
• Smart Grid Interoperability Panel (NIST)
• Wi-Fi Alliance
• ZigBee Alliance
• WiSUN
Logistics
Expertise with large-scale production
ramps—TI production, assembly and test
sites are auditable.
www.ti.com/smartgrid-blog
Texas Instrumentswww.ti.com/smartgrid
Smart Grid Solutions Guide 2014 | 3
Smart Grid Infrastructure
Data Concentrator Solutions
Automatic metering infrastructure (AMI) and
automatic meter reading (AMR) provide the
necessary means to measure, analyze, collect
energy usage and communicate that data
to a central database for billing, troubleshooting,
and analyzing. It would not be practical,
technically as well as economically, for all
meters to directly communicate with utility
servers. Data concentrator applications are
important nodes in the AMI and are networked
with several utility meters and central utility
servers. These nodes enable communication
of the data between the meters and the utility
servers. Data-concentrator nodes at several
points in the infrastructure securely aggregate
data from a manageable number of meters and
sends it to the utility servers.
Power
Lines
System
Power
PWM
AC/DC
Low-Power
RF Solutions
Antenna
CC11xx/CC430/
ISM-Band SoC
Radio
CC25xx
802.15.4 SoC
Radio, MCU
Range
Extender
SPI or UPP
UART/SDIO
Application Processor:
Network/MAC Manager/
Analytics
Clock
LCD
External
Modem
Sitara™
(ARM® Cortex™ -A8 AM335x)
or
Tiva™ C Series (Cortex-M4)
or
Microprocessors
Wi-Fi® and
Wi-Fi +
Bluetooth®
Ethernet
Digital
Isolation
I2C
Wired
Interface
USB
RS-232
or RS-485
Ports
LED Driver
SPI or UART
Power Line Communications (PLC)
Coupling
HV
Cap Transformer
AFE
+
+
TMS320F28xx
Flexible PLC
Modem 32-Bit MCU
-
Surge Protector
Data Concentrator System
Isolation to prevent damage
from high-voltage currents
Three-phase PLC module support
On-board 120-/240-V power supply
Supports control and data
communications:
2× Ethernet, 3-phase PLC
interface, sub-1-GHz
and 2.4-GHz RF,
2× RS-232, 3× RS-485
AM335x processor:
• SitaraTM processor for upper-level
data concentrator stack and
communications
• Full Linux BSP supported by TI
Temperature sensor
Sub-1-GHz and 2.4-GHz RF
Infrared receiver and transmitter
Designed to best practices
for high-speed systems:
Good reference for design
passing ESD system tests;
BOM and schematics
available
Clock
The communication mode largely
depends on the power infrastructure
and can be either wired or wireless.
Wired communication is comprised of
Power Line Communication (PLC) and
in some cases with serial or Ethernetbased communication where PLC is
not suited for the infrastructure. The
wireless mode is comprised of mainly
low-power RF (IEEE 802.15.4g protocol)
communication and in some cases the
existing cellular network. The communication from the concentrator to the
utility servers can be via Ethernet, GSM,
GPRS, WiMAX or telecom networks.
Hardware Features
Evaluate TI’s solutions for
data concentrator based
on ARM® technology.
Support up to 2000 nodes
G3-PLC standard,
PRIME standard,
IEEE-1901.2 standard
EEPROM
2× USB
2× Ethernet
2× RS-232
3× RS-485
Products for Data Concentrators
Description/Device
To Core
Network
Key Benefits
Tiva™ C Series ARM
Cortex-M4-Based MCUs
(TM4C123x Series)
• Up to 1-GHz Cortex-A8 32-bit RISC microprocessor
• Extensive peripheral set (2× Gbit-Ethernet, CAN, USB, 8× UARTs extended from PRU, ...)
• Flexible communication protocols
• Linux® community, Android®, Windows® Embedded CE, DSP/BIOS™ Real-Time Kernel
and RTOS ecosystem of development partners
• Up to 80-MHz core
• 256KB single-cycle flash, 32KB single-cycle SRAM
• Rich interface featuring 8× UARTs, USB, CAN, up to 43 GIPOs, etc.
• 2× 12-bit ADC with 12 analog input channels
C2000™ 32-bit real-time
MCUs Piccolo™
Floating-Point Series
• PLC accelerators
• Integrated real-time control peripherals
• Support multiple PLC modulations
Sitara™ processors
(AM335x Series)
AM335x
Processor
ARM®
Cortex™-A8
EMAC
RJ-45
EMAC
RJ-45
UART
To PLC Network
F28PLCxx
UART
MCU
AFE031
Get more information: www.ti.com/solution/data_concentrator
4
|
Smart Grid Solutions Guide 2014
www.ti.com/smartgrid
Texas Instruments
Smart Grid Infrastructure
Signal Chain and Power Products
Device
Description
SimpleLink™ CC1200 Low-power, high-performance RF transceiver
SimpleLink CC1120
High-performance RF transceiver for narrowband systems
PWM controller with/without integrated 700-V startup switch. constant-voltage, constant-current controller with primary-side regulation, QR green mode, optocoupler
UCC28710/700
less feedback, very-low no-load power, high efficiency
LM3671
2.7-V to 5.5-V input, 600-mA output, 2-MHz step-down DC-DC converter optimized for powering low-voltage circuits
TLV62080
2.5-V to 5.5-V input, 1.2-A step-down converter in 2x2-mm package with high efficency over wide output-current range
ADS8558/7/6
12/14/16-bit, 6-channel, simultaneous-sampling SAR ADC, supports up to 730 kSPS in parallel interface mode, up to 91-dB SNR
ADS131E04/06/08
4/6/8-channel, up to 24-bit Δ∑, simultaneous sampling AFE for relay protection, power monitoring, power quality, up to 64 kSPS, 107-dB SNR
See more Signal Chain and Power recommendations on pages 12 and 13.
Power Line Communications (PLC)
Power Line Communications (PLC) technology is being adopted
by electric utilities around the world for their Advanced Metering
Infrastructure (AMI) and Home Area Networks (HANs). PLC offers
the advantage of reusing existing infrastructure to lower costs,
retain reliable performance and maintain scalability to larger
network sizes.
Modern PLC networks utilize OFDM modulation techniques to
increase data throughput and improve reliability in inherently noisy
environments such as electric grids. Texas Instruments has long
been a pioneer in developing OFDM communications technology.
TI’s PLC modems provide the best performing platform for today’s
Smart Grid networks due this legacy of OFDM expertise and TI’s
modems are being deployed by utilities around the world.
For smart meter OEMs, TI’s PLC solutions provide the flexibility of
a single hardware and software design that can support multiple
standards and therefore a single global platform. This will greatly
reduce research and development costs and speed time to market.
Integrated Analog Front End (AFE)
TI’s new AFE032 is a low-cost, integrated AFE device capable of
transformer-coupled connections in a PLC system and can be
controller by a digital signal processor (DSP) or microcontroller. This
AFE is suited for driving high-current, low-impedance lines with up
to 1.9 A into a reactive load.
PLC Standards Support
PLC Standard
Frequency Band
PRIME, G3 or IEEE-P1901.2
CENELEC
TMS320F28PLC83 + AFE03x
TI Chipset
G3
FCC, ARIB
TMS320F28M35 + AFE032
IEEE-P1901.2
FCC
TMS320F28M35 + AFE032
TMDSPLCKIT-V3 C2000™ Power Line
Modem Developer’s Kit
• Two PLC modems
• PRIME, G3 or IEEE P1901.2 PLC software
• Zero config GUI PLC diagnostic tool
• Built-in USB JTAG emulation
• Includes Code Composer Studio™
Integrated Development Environment
• Connect to TI Data
Concentrator Development
tool TMDSDC3359
• Plug-In System-OnModule (SOM) available
(See page 15)
Integrated Analog
Front End
C2000™
Processor
I2C
Power Line Communication Modem System
Texas Instrumentswww.ti.com/smartgrid
Learn more at www.ti.com/plc
Smart Grid Solutions Guide 2014
|
5
Smart Electricity Meter
Electric meter requirements around the world are rapidly evolving in response to market forces and governmental regulations that
mandate Smart Grid deployments in most areas of the globe. Smart Grid applications such as dynamic pricing, demand response,
remote connect and disconnect, outage management, network security and reduction of non-technical losses are driving the need
for increasing technological sophistication in today’s smart electric meters.
Metrology
Metrology Products
At the heart of any smart meter is the basic energy measurement
function. It is critical that utilities and consumers can rely on
the accuracy, security and reliability of this metering capability.
Energy-measurement products from Texas Instruments are
designed to meet all of the requirements of ANSI C12.20 and
IEC 62053 accuracy for Class 0.2 and Class 0.5 meters across
the entire temperature range and with a full 2000:1 dynamic
input range.
Protecting meter integrity is a key to reducing non-­technical
losses in the field. TI’s electric meter metrology solutions include
sophisticated anti-tampering protection.
Host Processors
Host processors for meters must be able to support the multiple
applications and external interfaces required in smart meters
today. Data management applications for meters such as DLMS/
COSEM and communication stacks such as ZigBee® Smart Energy
and wireless M-Bus are all evolving to require more memory and
increased processor performance.
Advanced Meter Infrastructure (AMI) Solutions
AMI networks require robust communications between the
individual meters and the data concentrators which aggregate
meter data in a neighborhood area before sending that information to the utility’s central office through a backhaul link. AMI
networks are either RF (mesh or star topology) or Power Line
Communications (PLC). The choice between RF or PLC networks
is usually driven by grid topology and geographical environment
because these factors have enormous influence on network performance and infrastructure cost. TI’s solutions for AMI networks
span both RF and PLC. These solutions also support most industry
standards, including IEEE-802.15.4g, PRIME, G3, IEEE-P1901.2
and ITU-G.990x.
RFID and NFC
RFID systems using Near Field Communication (NFC) are an
attractive way to deploy pre-payment. TI’s solutions cover the
entire NFC ecosystem that includes a complete line of ultra-lowpower transceiver devices and a broad offering of dynamic and
static tags. Low-cost, easy-to-use hardware and software solutions lower barriers to using NFC designs that can achieve added
connectivity, more flexibility and faster time to market. Learn more
at: www.ti.com/rfid and www.ti.com/nfc
6
|
Smart Grid Solutions Guide 2014
Device
MSP430F673x SoC
MSP430F677x SoC
MSP430AFE2xx
Key Benefits
Single-phase SoCs with 128KB flash, 320-segment LCD
controller, anti-tamper protection, standby power consumption
less than 500 nA, TI’s Energy Library firmware
Three-phase SoCs with 512KB flash, 320-segment LCD
controller, anti-tamper protection, standby power consumption
less than 500 nA, TI’s Energy Library firmware
Analog front end with six 24-bit sigma-delta channels, 103-dB
performance, integrated PGA and internal reference
Host Processors
Device
Tiva™ C Series LM4Fx
Cortex™-M4 MCUs
Sitara™ AM335x
Processors
Key Benefits
80-MHz, 256KB flash, low-power RTC, TivaWare™ for
C-Series driver library pre-loaded into every device
Up to 1 GHz, three-level cache memory, DDR2 and low-power
DDR, complete Linux® board support package
Wireless Connectivity Products
Device
SimpleLink™
CC1120
SimpleLink
CC1200
SimpleLink
CC2538 SoC and
CC2520 2.4-GHz
Transceiver
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Key Benefits
Ultra-low-power transceiver for narrowband systems
Channel spacing down to 12.5 kHz
170/315/433/868/915/950-MHz ISM/SRD bands
IEEE 802.15.4g, ETSI, FCC and ARIB regulatory compliance
Excellent receiver sensitivity: –123 dBm at 1.2 kbps,
–110 dBm at 50 kbps
64-dB adjacent channel selectivity at 12.5-kHz offset
Only 2-mA consumption in RX Sniff Mode
High-performance transceiver for broadband systems
Up to 1 Mbps in transmit and receive
169/433/868/915/920-MHz ISM/SRD bands
Dedicated package handling for 802.15.4g
ETSI, FCC and ARIB regulatory compliance
Excellent receiver sensitivity: –123 dBm at 1.2 kbps,
–110 dBm at 50 kbps
60-dB adjacent channel selectivity at 12.5-kHz offset
Only 2-mA consumption in RX Sniff Mode
Complete 2.4-GHz ISM SoC with ZigBee® PRO/SE
application profile software
Robust link budget and best-in-class selectivity for
noisy RF environments
Improve range with CC259X PA/LNA front end
RFID and NFC
Device
Key Benefits
RF430CL NFC Smart
Interface Tag
Dynamic NFC transponder for service interface
• ISO14443B RF compliant and NFC Tag Type-4 compliant
• Up to 848-kbps transfer rate with serial interface to MCU
TRF7970A Transceiver
Multi-protocol fully integrated 13.56-MHz RFID/NFC
transceiver IC for prepayment
• ISO 14443A/B, ISO 15963 support and NFCIP-1, NFCIP-2
• Peer-to-peer, card emulation, reader/writer functionality
• TI-supported firmware stack for MIFARE™, NFC
www.ti.com/smartgrid
Texas Instruments
Smart Electricity Meter
Smart Meter Board (SMB)
NL
PWM
AC/DC
System
Power
Metrology
External Options for Micro
External Ref
SVS/Reset IC
ISENSE
MSP430™
E-Meter SoC
MCU, RTC, LCD
Isolation
Amplifier
VSENSE
External RTC
Home Area Network (HAN)
Wireless Communication
2.4-GHz Solution
WLAN Solution
Antenna
Application
Processor
Antenna
SimpleLink™
CC25xx
802.15.4 SoC
Radio, MCU
Application Processor
Stellaris® Cortex™ M4/
Sitara™ MPU
Power Line Communication (PLC)
PWM
TX
ADC
RX
ESD
SimpleLink
CC3000
RF Mesh
SimpleLink
CC112x/CC1200
ISM-Band
Radio
TMS320F28PLC
PLC Processor
Auxiliary Options
Relay
Driver
Range
Extender
The SMB is a modular development platform
incorporating key TI Smart Grid devices to
demonstrate the capabilities of a smart meter.
SMB is a unique tool that performs energy
or electricity metering and it also has the
capability of transferring key metering data
via wired PLC and wireless (Wi-Fi®, ZigBee®,
Sub-1 GHz). It is designed to showcase a
simple system for automatic meter reading
(AMR) and automatic metering infrastructure
(AMI). Watch video at www.ti.com/smb3
Antenna
Matching
Circuit
Other Options
Digital
Isolation
Wired
Interface
(RS485)
GSM/GPRS
Module
Pre-Payment
(Wireless)
Smart E-Meter System
Analog Products
Device
UCC28910
TPS5401
TPS54227/327
Description
Application
PWM HV switcher with 700-V integrated power FET and primary-side regulation. The UCC28910 is
dedicated to flyback power supplies and provides isolated output voltage and current regulation without
the use of an optical coupler
Cost-optimized 42-V, 0.5-A step-down DC/DC converter; cap-drop off-line power supplies
4.5-V to 18-V input, 2-A and 3-A output respectively; DC/DC step-down converter, adaptive on-time
D-CAP2™ enables high efficiency over load range, fast transient response, allows use of low ESR caps,
adjustable soft start
AC/DC supply
Step-down regulator
Step-down regulator
SN65HVD3082/85/88
200-kbps/1-Mbps/20-Mbps capable, half-duplex transceivers, operate with very-low supply current
RS485 interface
ISO7131
3-channel, small-footprint, digital isolators provide galvanic isolation up to 2500 VRMS for 1 minute per
UL and 4242 VPK
Digital isolation
Optimized Solution
E-meter, data concentrator,
grid infrastructure
Low-cost cap-drop solution
E-meter, data concentrator,
grid infrastructure, general
system supply
E-meter, data concentrator,
grid infrastructure
E-meter, data concentrator,
grid infrastructure
See more Power and Signal Chain recommendations on pages 12 and 13.
TI Designs Reference
Design Library
www.ti.com/tidesigns
www.ti.com/smartgrid-blog
Texas Instrumentswww.ti.com/smartgrid
Smart Grid Solutions Guide 2014
|
7
Flow Meter
Smart Metering for Gas/Water/Heat/Heat Cost Allocator
A
B
C
D
E TESTCUM
Sensors and Signal Chain
Communications
MAX
GAL
Sub-1-GHz Solutions
Sub-1 GHz
Flow Sensors
Microcontroller
Temp. Sensors
2.4-GHz Solutions
2.4 GHz
Pressure Sensors
Range
Extender
Range
Extender
Other Solutions
Prepayment
RFID/NFC
Valve Control
(Motor Driver)
System Power
Battery
RS-485/RS-232
GSM/GPRS
Wired M-Bus
Optional Functionalities
Power Management
Smart Flow Meter System
Smart Gas/Water/Heat Meter Products
Function
Part Number
Key Features
Category
Ultra-Low-Power Microcontrollers
MSP430F448/F449
(48/60-KB Flash)
MSP430F417
MSP430F448
32KB flash, 96-seg LCD
48/60KB flash, 160-seg LCD, 2 USARTs, hardware multiplier, temp sensor
60KB flash, LCD, scan interface peripheral for rotation detection under low-power mode
(supports multiple types of sensors)
Next-generation MCU platform with embedded FRAM
128KB flash, 320-seg LCD, RTC with battery backup, power management
256KB flash, 160-seg LCD, RTC with battery backup
512KB flash, 320 segment LCD, RTC with battery back-up power management
Sub-1-GHz SoC, LCD; CC1101 transceiver, MSP430™ MCU
MSP430FW429
MSP430FR5969
MSP430F6736
Apps Processor
MSP430F6638
MSP430F6779
MCU + RF System-on-Chip (SoC) CC430F6147
General Purpose
Dedicated Flow-Meter
Devices
Embedded FRAM
High Performance
MCU + RF SoC
Connectivity
Sub-1 GHz
2.4 GHz
SimpleLink™ CC1101
SimpleLink CC1120
SimpleLink CC1175
SimpleLink CC110L
SimpleLink CC1190
SimpleLink CC2510
SimpleLink CC2520
SimpleLink CC2530
SimpleLink CC2538
SimpleLink CC2590
SimpleLink CC2591
WL18xx
Wired M-Bus
SimpleLink CC3000
TSS721A
Transceiver; low cost, low power; –116-dBm sensitivity
Transceiver; high performance, narrowband, –123-dBm sensitivity
Transmitter; high performance, narrowband, 16-dBm TX power
Transceiver; cost-optimized, –116-dBm sensitivity
RF front end; 27-dBm (0.5-W) TX power
Low-cost SoC; 8051 MCU (up to 32KB flash), –103-dBm sensitivity
Transceiver; 8051 MCU (up to 256KB flash), –98-dBm sensitivity
SoC; 8051 MCU (up to 256KB flash), –97-dBm sensitivity
SoC; Cortex™-M3 MCU (up to 512K flash, 32K RAM)
RF front end; cost-effective, for low-power apps, 14-dBm TX power
RF front end; cost-effective, for low-power apps, 22-dBm TX power
Transceiver module, integrated Wi-Fi® + dual-mode Bluetooth®, MIMO, extended range, Wi-Fi
direct concurrent operation
Transceiver module, self-contained Wi-Fi network processor, one-step configuration for Internet
Meter-Bus (M-Bus) transceiver; meets EN1434-3 standard
Proprietary RF
wM-Bus
Range Extender
Proprietary RF
ZigBee®/IEEE 802.15.4
Range Extender
Wi-Fi
Wired M-Bus
Power Management
PMIC
Step-Down Regulator
TPS65290
TPS65250
TPS62730
TPS62740
Power management IC for gas/water meters
Power management IC with “last gasp” storage and release circuit
Step-down converter with Bypass Mode for ultra-low-power wireless applications
Ultra-low IQ, step-down converter for low-power wireless applications
For other Analog and Power Management Solutions, see pp 12-13.
Gas/Water Meter
E-Meter
Flow (Gas/Water) Meters
Flow (Gas/Water) Meters
Additional Smart Functionalities
TRF7960A
Prepayment (RFID/NFC)
Valve Control (Motor Driver)
8
|
TRF7970A
DRV8830
DRV8832
DRV8833
DRV8835
DRV8836
DRV8837
Smart Grid Solutions Guide 2014
RFID/NFC reader/writer IC; fully integrated protocol handling
RFID/NFC transceiver IC (supports reader/writer, peer-to-peer and card-emulation modes);
fully integrated protocol handling; compliant to NFC standards NFCIP-1 and NFCIP-2
Secure I2C control interface; up to 1-A continuous current with inrush protection
Speed regulation: Constant speed over lifetime of battery
Up to 3-A continuous current with inrush protection
Up to 3-A continuous current in a 2 x 3-mm package; split VM/VCC supplies
Tiny 2 x 3-mm package; dedicated sleep pin; 40-nA sleep current
Up to 1.8-A continuous current in a 2 x 2-mm package; split VM/VCC supplies
www.ti.com/smartgrid
RFID/NFC
Brushed
Brushed/Stepper
Brushed
Texas Instruments
Flow Meter
Smart Metering for Gas/Water/Heat/Heat Cost Allocator
Complete system solution for battery lifetime optimization:
Sensing, MCU, Power, Communication and Software
TI Flow Sensing Solutions
Sensing Techniques
Sensor Type
TI Solution
Benefits
Rotation Detection
• LC sensors
• Magnetic Sensors (Resistor
ladder, GMR sensors)
• Optical sensors
flow measurement in low
Flexible solution based on • Continuous
power mode
AFE + TDC + MCU + SW
• 5X less power consumption compared to
optimized combo
equivalent software implementation
Ultrasonic Time of
Flight (ToF)
Piezzo ceramic PMUT, CMUT
Ultra-low-noise signal chain:
• Offers customizable system to meet
Flexible solution based on
various system requirement
AFE + TDC + MCU + SW • Enables system differentiation for
optimized combo
developers
• Provides optimized combination for accuracy and low power
Others
Magneto Inductive (MID)
ADC tuned for MID
•
•
•
•
Actions
High input impedance
24-bit dynamic range
Fast wake-up
Ultra-low standby current
Wireless M-Bus Solutions
Hardware and Software Support for Both 169 MHz and 868 MHz
Key Features
• Best blocking and selectivity
performance for a robust and costoptimized solution
• Packet loss reduction mechanism to
improve battery lifetime
• “RX Sniff” mode maintains best RF
performance in RX while reducing
power consumption
• Optimized DC/DC energy management
solution for extending battery lifetime
• Analog, digital, software evaluation kits
immediately available
• See TI’s wM-Bus Guide
www.ti.com/wmbus
• wM-Bus tool page
www.ti.com/tool/wmbus
wM-Bus Hardware and Software Kits
Radio
Frequency
Band
Microcontroller
Option 1: General
Option 2: High Transmit Power Software
868 MHz
SimpleLink™ (CC1120): CC1120DK
Includes TrxEB (MCU, USB I/F, LCD, accelerometer, light sensor)
SimpleLink
(CC1120 + CC1190):
CC1120-CC1190EMK868
169 MHz
(MSP430F5438):
MSP-EXP430F5438
or
(MSP430FG4618):
MSP-EXP430FG4618
SimpleLink (CC110L):
CC1101EMK868-915
or
(CC1101): CC110LEM-868-915-RD
or
(CC1120): CC1120EMK-868-915
SimpleLink (CC1120 + PA):
CC1120 Skyworks EM +
30 dBm
Other
Solutions
(CC430F6147): EM430F6137RF900
wM-Bus
Stack
—
Power Management EVMs for wM-Bus
Issue to Address
Efficient power supply from primary batteries (Supports all MCU+RF
kits listed above)
High-power supply (RFPA)
Capacitor-based battery assistance
Texas Instrumentswww.ti.com/smartgrid
Solution
Evaluation Tool
TPS62730
TPS62730EVM
TPS62065/67
TPS62065-67EVM-347
TPS61251
TPS61251EVM-517
Smart Grid Solutions Guide 2014
|
9
Smart Energy Management for Homes and Buildings
TI offers complete system solutions for measurement, management
and communication of energy systems for smart homes and buildings
Smart Energy Gateway/Hub Solution
• Large software foundation for base-line validation
• Enable seamless profile integration for smart energy,
lighting and building automation
• Easier coexistence validation
USB Host/Device
USB
Power
Switch
USB Hosts
USB
USB
Hub
Controller
DC
Power Jack
Switch
DDR3
Memory
NAND
Flash
Clock
PMIC
TPS65217D
DDR IF
GPMC
Clock
Power GPIO I2C
Reference Design
USB
AM3352
ARM CortexTM A8 Processor
EMAC
(RMII)
®
DP83848J
10/100
Ethernet PHY
POE
PSE
RJ-45
MMC
Wi-Fi®
JTAG
GPIO
UART
Range
Extender
UART GPIO
2.4 GHz
ZigBee®:
CC2538, CC2530
BLE: CC2540, CC2541
GPIO SPI
SPI
NFC Module
RF430CL330H
Boot
Flash
EEPROM
(Config)
2
I C
3.3 V
DC/DC
TI Designs Reference Design Library
www.ti.com/tidesigns
Sensor Network
TI provides connectivity solutions for
sensors:
Longevity: High idle-power consumption
and frequent “listening” reduce lifetime of
device battery
• TI implements 802.15.4e to increase
battery life to >10 years
Reliability: Noise and instability in
wireless channels and slow recovery
• TI implements TSCH and compensated
RF with PLC >99.999% data reliability
Coverage: Many “hops” needed to cross
large area or long distance inside building
for “flat” network
• TI implements PLC/RF combo nodes
for seamless hybrid communications
Scalability: Extend network size from
100s to 1000s with “plug and play”
• TI implements standard IPv6 with RPL
for complete mesh formation in less
than one second
10
|
Smart Grid Solutions Guide 2014
Sub-Meter Class 0.5 Single-Phase Metrology, AnalogFront-End Evaluation Module
• Single-phase, Class 0.5 electricity meter/sub meter
• 24-bit sensor input with AMI capability and RF interface:
ZigBee®, wM-Bus/<1 Ghz and Wi-Fi®/PLC via UART
• Software features: 1-phase 0.5% energy library and
anti-tampering
(Read more on page 14)
Sub-Metering/Smart Plug Solutions
• Sub-0.5% accuracy metrology solution
• Easy wireless
Line
Power
connection
• Reference design
L N
VCC
V–
RShunt
VCC
V+
VSense
ADC
MCU
I+
ISense
I–
MSP430AFE2xx
Energy Measurement IC
ZigBee®
or
Wi-Fi®
CC2530/CC2591
or
CC3000
Load
Smart Plug Solution
www.ti.com/smartgrid
Texas Instruments
Smart Energy Management for Homes and Buildings
Smart Home and Building Products
Device
Wireless Communication
Description
Host Processors
AM335x Cortex™-A8
MSP430F543xA
Powerful and scalable host-processor for home gateways and high-end in-home displays
Host processor with up to 256KB flash for applications such as a simple in-home display
Energy Measurement ICs
MSP430AFE2xx
MSP430F471xx
Single-phase energy measurement IC for sub-meters
Poly-phase energy measurement IC that can also be used for multi-outlet smart power strips and PDUs
TI’s wireless solutions for Smart
Grid communication include more
options to create infrastructure,
smart meters, and home automation systems.
Communication
SimpleLink™ CC2520/2538/2530 2.4-GHz transceivers and SoCs for ZigBee® and 802.15.4-based communications
SimpleLink CC11xx
Sub-1-GHz transceivers for backhaul and proprietary HAN communication
High-peformance, power-optimized 8.02.11 b/g/n and dual-mode Bluetooth® on a single chip;
WiLink™ 8 WL18xx
extended range, high throughput and multi-channel, multi-role features
SimpleLink CC3000
802.11 b/g solution for Wi-Fi® implementation without previous Wi-Fi or RF experience
SimpleLink CC1200
SimpleLink CC1200 low power, high performance RF transceiver
SimpleLink CC1120
High performance RF transceiver for narrowband systems
SimpleLink CC2591
Radio PA/LNA for extended range
TPS650250
Low-cost power-management IC for the AM335x processor
DP83848J
Ethernet PHY (10/100 Mbps) for home-gateway application
Get more information:
www.ti.com/connectmore
Wireless Connectivity Solutions for Smart Grid
Sub-1 GHz
6LoWPAN www.ti.com/6lowpan
www.ti.com/rfperformanceline
• CC1200: Broadband transceivers,
sub-1 GHz with data rates up to 1 Mbps
• CC1120: High-performance RF
transceiver for Narrow-band systems
• CC110L: Low-cost RF transceiver for
cost-sensitive systems
• CC430: Enables smarter RF solutions
with MSP430™ MCU plus low-power
RF IC
• Sub-1 GHz enables long-range
communications that support communication distances of several kilometers
• Gateway for remote, low-cost wireless sensors to connect to the Internet
and a wireless extension of wired IPv6
infrastructures
• Sub-1-GHz product family includes the
CC1180 network processor, CC430
complete system-on-chip (SoC),
CC1101/MSP430F5xxx platform and
6LoWPAN software stacks
• Supports large-scale mesh networks
and applications such as smart grid,
security, building automation, street
lighting and other wireless sensor
networks
• Available range extender for CC1190
ZigBee® (IEEE 802.15.4/
ZigBee PRO) www.ti.com/zigbee
• Complete hardware and software for
the ZigBee-Compliant Platform (ZCP),
certified by a ZigBee alliance-approved
test house
• Free IEEE 802.15.4 MAC software
and golden unit status Z-Stack™
protocol stack
• High-performance CC253x radio offers
excellent coexistence with WLAN,
Bluetooth® and other 2.4-GHz solutions
• Smart-energy and home-automation
application profiles and support
• Range extenders available for CC2590
and CC2591
• Development kits and tools
Bluetooth/Bluetooth Low Energy
www.ti.com/bluetoothsolutions
• Portable, battery-powered devices
• Ultra-low power consumption enables
sensor applications to operate for >1
year on a coin-cell battery
• Leading RF performance – Up to
+97-dB link budget for long range
and excellent coexistence with other
2.4-GHz devices
• One-chip integrated solution –
Controller, host and application on
one 6 x 6-mm device, which reduces
required PCB area; applications can
be written directly onto the CC254x,
Texas Instrumentswww.ti.com/smartgrid
which supports both analog and
digital peripherals
• Other Bluetooth options: CC256x
Bluetooth/Bluetooth low-energy
dual mode for short-range, portable
applications; WiLink™ Wi-Fi® plus
Bluetooth/Bluetooth low-energy dual
mode for high performance WLAN
Wi-Fi www.ti.com/wifi
• SimpleLink™ CC3000: Self-contained
802.11 b/g solution enables easyto-implement Internet connectivity
with SmartConfig™ technology;
embedded Wi-Fi and networking
software including drivers, stack and
supplicant; allows Wi-Fi implementation quickly without previous Wi-Fi
or RF experience
• WiLink combo solutions: WL18xx
modules integrate high-performance
802.11 b/g/n and dual-mode Bluetooth
platform on a single chip with bestin-class coexistence technology and
power optimization
• TI’s WLAN technology allows secure,
high-throughput, extended-range,
multi-channel and multi-role performance and reliable Wi-Fi connectivity
of electronic devices to each other, the
Internet and wired networks
(See wireless development tools on page 16.)
Smart Grid Solutions Guide 2014
|
11
Signal Chain and Power Management Solutions
Analog Products
Device
Description
Type
Application
Digital Isolation
E-Meter, Data Concentrator.
Grid Infrastructure
E-Meter, Data Concentrator,
Grid Infrastructure
Digital Isolation
ISO7131
ISO7140/41
3-channel, small-footprint digital isolators provide galvanic isolation up to 2500 VRMS for 1 minute per
UL and 4242 VPK
4-channel, small-footprint digital isolators provide galvanic isolation up to 2500 VRMS for 1 minute per
UL and 4242 VPK
Digital Isolation
RS485 (Isolated & Non-Isolated)
SN65HVD3082/85/88
200-kbps/1-Mbps/20-Mbps capable, half-duplex transceivers, operate with very low supply current
RS485 Interface
SN65HVD3080/83/86
200-kbps to 20-Mbps capable, full-duplex transceivers, operate with very low supply current
RS485 Interface
ISO3080/82/86/88
Isolated 5-V full- and half-duplex RS485 transceivers, provide 2500 VRMS of isolation for 60 s
Isolated
RS485 I/F
E-Meter, Data Concentrator,
Grid Infrastructure
E-Meter, Data Concentrator,
Grid Infrastructure
E-Meter, Data Concentrator,
Grid Infrastructure
External RTC
BQ32000
Real-time clock
RTC
E-Meter
E-Meter, Flow Meter, Grid
Infrastructure
E-Meter, Flow Meter, Grid
Infrastructure
E-Meter, Flow Meter, Grid
Infrastructure
Relay/Actuator Drivers
ULN2003
Family of relay drivers
Relay
DRV777
7 low-output-impedance drivers minimize power dissipation; 140 mA/channel, 1 A when tied together,
20-V-capable output pins
Low-voltage motor/actuator driver with serial interface. The device has one H-bridge driver which can drive 1-A
peak output current
Relay
DRV8830/60
Relay
Ethernet PHY
TLK105L
10/100 Ethernet PHY, error free to 150 meters, cable diagnostics, Auto-MIDX, supports MII and RMII
Interface
DP83848K
10/100 Ethernet PHY, error free to 130 meters, Auto-MIDX, supports MII and RMII
Interface
DP83640
IEEE 1588 precision-time-protocol transceiver for real-time industrial connectivity. Packet time stamps for clock
synchronization
Interface
Data Concentrator, Home
Area Network
Data Concentrator, Home
Area Network
Data Concentrator, Home
Area Network
12/14/16-bit, 6-channel simultaneous-sampling ADC, up to 730 kSPS in parallel interface mode, up to 91-dB SNR
12/14/16-bit ,8-channel simultaneous-sampling ADC, up to 650 kSPS in parallel interface mode, up to 91-dB SNR
Interface
Interface
E-Meter, Grid Infrastructure
E-Meter, Grid Infrastructure
4/6/8-channel, up to 24-bit, simultaneous-sampling AFE for relay protection, power monitoring, power quality,
up to 64 kSPS, 107-dB SNR
1/4/8-channel, up to 24-bit, simultaneous-sampling AFE for power monitoring, quality and protection,
up to 144 kSPS, 111-dB SNR
Interface
E-Meter, Data Concentrator
Interface
E-Meter, Data Concentrator
Fully-differential isolation amplifier for energy metering; SiO2 barrier up to 4250 VPK and resistant to magnetic
interference
20-MHz, second-order, isolated delta-sigma modulator for current-shunt measurement, SiO2 barrier up to 4250 VPK
Analog Isolation
E-Meter, Grid Infrastructure
Analog Isolation
E-Meter, Grid Infrastructure
Wide VS: +4.0 V to +36 V (±2 V to ±18 V), low offset voltage, near-zero drift, low IQ, high input impedance and
rail-to-rail output swing
VS operates from ±2 V to ±18 V, ultra-low offset and drift, low IQ
Interface
Grid Infrastructure
Interface
Grid Infrastructure
SAR ADC
ADS8558/7/6
ADS8528/48/68
Delta-Sigma (Δ∑) ADC
ADS131E04/06/08
ADS1271/4/8
Analog Isolation
AMC1100
AMC1204/B
Op Amps
OPA4188/71/40
OPA4277
External Reference
LM4050
LMV431
Precision micropower, shunt-voltage reference, external stabilizing capacitor
1.24-V shunt regulators capable of adjustment to 30 V
Voltage Reference E-Meter, Grid Infrastructure
Voltage Reference E-Meter, Grid Infrastructure
ESD
TPD1E10B06/B09
TPD4E1U06
TPD2E007
Single channel ESD protection in small 0402 package, ±30-kV IEC air-gap, over ±30-kV contact, bipolar or
bidirectional signal support
Quad-channel, ultra-low-cap ESD device, offers ±15-kV IEC air-gap and ±15-kV, suitable for multiple
applications like USB
2-channel ESD protection offers system-level ESD solutions for wide range of industrial applications like RS485, RS232
ESD Protection
E-Meter, Grid Infrastructure
ESD Protection
E-Meter, Grid Infrastructure
ESD Protection
E-Meter, Grid Infrastructure
Temperature Sensors
TMP275
TMP108
TMP75/LM75A
12
|
±0.5°C accurate from −20°C to +100°C, serial output, SMBus and two-wire interface
±0.75°C accurate from –20°C to +85°C, ±1°C from –40°C to +125°C, features SMBus and two-wire interface
±1.5°C to ±3°C accuracy depending on temperature range, features SMBus and two-wire interface
Smart Grid Solutions Guide 2014
www.ti.com/smartgrid
Temperature Sensor E-Meter, Grid Infrastructure
Temperature Sensor E-Meter, Grid Infrastructure
Temperature Sensor E-Meter, Grid Infrastructure
Texas Instruments
Signal Chain and Power Management Solutions
Power Management Products
Device
Description
Type
Application
Isolated AC/DC Power Solutions
UCC28710/700
PWM HV switcher with 700-V integrated power FET and primary-side regulation. The UCC28910 is dedicated to flyback
power supplies and provides isolated output voltage and current regulation without the use of an optical coupler
PWM controller with/without integrated 700-V startup switch. Constant-voltage, constant-current controller with
primary-side regulation, QR green mode, optocoupler-less feedback, very-low no-load power and high efficiency
UCC28600/610
QR/DCM PWM controller, excellent efficiency at full load, low power consumption at no load; small footprint
UCC28910
AC/DC Supply
AC/DC Supply
AC/DC Supply
E-meter, Data Concentrator,
Grid Infrastructure
E-meter, Data Concentrator,
Grid Infrastructure
E-meter, Data Concentrator,
Grid Infrastructure
Cap-Drop Power Solutions
TPS5401
TPS54060/
160/260
LM5017
Cost-optimized, 42-V, 0.5-A step-down DC/DC converter; cap-drop off-line power supplies
DC/DC switching power supply: 60-V, 0.5-A/1.5-A/2.5-A step-down DC/DC converters with Eco-mode™ for light
load efficiency and very low IQ
100-V, 600-mA, constant on-time, synchronous buck regulator. Can also be configured in flybuck mode
Step-Down Regulator Low-Cost ,Cap-Drop Solution
Step-Down Regulator 60-V, Cap-Drop Solution
Step-Down Regulator E-Meters (Low Cost)
DC/DC Solutions
TPS54478
TPS5432
TLV62065
LM3671
TLV62080
TPS62560
TPS62240
TPS54227/
327/427/627
TPS62730
LMR12010
TPS63030/1
TPS63060/1
LM2733
LM5001
Grid Infrastructure,
Step-Down Regulator E-Meter,
Processor Power
Grid Infrastructure,
2.95- to 6-V input, 3-A output, value concious, 700-kHz synchronous step-down converter
Step-Down Regulator E-Meter,
Processor power
Grid Infrastructure,
2.9- to 5.5-V with 2-A output, 2x2-mm footprint, synchronous DC/DC step-down converter, up to 97% efficient
Step-Down Regulator E-Meter,
Processor power
2.7- to 5.5-V input, 600-mA output, 2-MHz step-down DC/DC converter, optimized for powering low-voltage circuits Step-Down Regulator E-Meter (1-Phase or 3-Phase)
2.5- to 5.5-V input, 1.2-A step-down converter in 2x2-mm package, high efficency over wide output-current range Step-Down Regulator E-Meter, Grid Infrastructure
2.5- to 5.5-V input with up to 600-mA output, synchronous step-down converter, optimized for low power
Grid Infrastructure,
Step-Down Regulator E-Meter,
or battery applications
Processor power
2- to 6-V input with 300-mA output, 2.25-MHz buck in 2x2 SON/SOT23; offers high efficiency and power-save
Grid Infrastructure,
Step-Down Regulator E-Meter,
mode at light loads
Processor power
Data concentrator, Grid
4.5- to 18-V input, 2-, 3-, 4- and 6-A output respectively; DC/DC step-down converter, adaptive on-time D-CAP2™
Step-Down Regulator Infrastructure, General
enables high efficiency over load range, fast transient response, allows use of low ESR caps; adjustable soft start
System Supply
For battery-powered applications. Companion power supply for low power RF devices; bypass mode saves 20-30%
Step-Down Regulator Flow Meters (Gas/Water)
battery current without compromising on transmit power; DCS-Control™ topology provides low output-voltage ripple
20-VIN, 1-A buck regulator, 30-nA low-shutdown IQ and switching up to 3 MHz. Offers internal soft start, currentStep-Down Regulator Data Concentrator
mode PWM control
General System Supply
DC/DC buck-boost regulators, 0.8 A, low IQ with up to 96% efficiency
Buck-Boost, Regulator (Battery Operated), Home
Area Network
General System Supply
DC/DC buck-boost regulators: 2.5- to 12-V input voltage with 93% efficiency and 2.25-A switch-current limit
Buck-Boost Regulator (Battery Operated), Home
Area Network
Step-Up/Boost
0.6/1.6-MHz boost converter with 40-V integrated FET switch and low RDS(on). Offers cycle-by-cycle current limiting
Data Concentrator
Regulator
Step-Up/Boost
75-V integrated MOSFET with a 1-A peak current limit for boost and SEPIC implementation
Data Concentrator
Regulator
2.95- to 6-V input, 4-A output, DC/DC switching power supply, 2-MHz synchronous step-down converter
Linear Regulators
TLV71310/11/
12/15/18
LP38691
TLV70710/11/
12/15
LP5907
PMICs
TPS65290
TPS650250
TPS65250
Capacitor-free, 150-mA, LDO with 1.5% regulation over temperature range. This next generation LDO was designed
to be stable without an output cap
500-mA, low-dropout, CMOS linear regulator with tight output tolerance and excellent AC performance with ultralow ESR ceramic caps
LDO
E-Meter, Data Concentrator,
Grid Infrastructure, Flow Meter
LDO
Data Concentrator
200-mA LDO with low IQ, tight output regulation (2% typ). Offers excellent line- and load-transient performance
LDO
Data Concentrator
250-mA LDO for RF and analog circuits, provides low noise, high PSRR, low IQ and low transient response
LDO
Data Concentrator
Power-management IC for gas/water meters
Low-cost PMU for AM335x
Power-management IC for e-meters with “last gasp” storage and release circuit
PMU
PMU
PMU
Gas/Water Meter
Grid Infrastructure
E-Meter
Voltage Supervisor and Reset ICs
TPS3831/9
TPS3700
TLV803/809/810
TPS3808
Chargers
Ultra-low power, 150-nA, ultra-small voltage supervisor
UV, OV voltage monitor; wide input voltage
Low-cost voltage supervisor with 200-ms reset delay
Highly-accurate (0.5% typ) supervisor with low IQ and adjustable reset delay
Voltage Supervisor
Voltage Supervisor
Voltage Supervisor
Voltage Supervisor
E-Meter, Grid Infrastructure
E-Meter, Grid Infrastructure
E-Meter, Grid Infrastructure
E-Meter, Grid Infrastructure
BQ24171
Highly-integrated 1- to 3-cell Li-ion/Li-polymer charger with battery detection, pre-conditioning, charge
monitoring and termination
Battery Charger
Home Area Network,
Flow Meter
BQ25504
Ultra-low-power boost converter with battery management for energy-harvester applications
Boost Controller,
Battery Charger,
MPPT Controller
Home Area Network, Wireless
Sensor Node
Texas Instrumentswww.ti.com/smartgrid
Smart Grid Solutions Guide 2014
|
13
Smart Grid Development Tools
Metrology: Single-Phase
Tool Identification
Description
Resources
Class 0.2 Single-Phase
Metrology, Analog-FrontEnd Evaluation Module
(EVM430-AFE253)
Single-phase, Class 0.2 electricity-meter/sub-meter (3 sigma-delta 24-bit sensor
inputs, 16KB flash, 0.5KB RAM) evaluation board. Comes with application note,
energy library and schematics. Features MSP430AFE253, the industry’s first
programmable analog front end microcontroller.
Get Started: Watch video at www.ti.com/afe-video
Contact TI representative
Support: MSP430™ Energy Library at
www.ti.com/tool/msp430-energy-library
Read application report at www.ti.com/lit/slaa494
Class 0.5 Single-Phase
Metrology, Analog-FrontEnd Evaluation Module
(EVM430-i2040)
Single-phase, Class 0.5 electricity-meter/sub-meter (4 sigma-delta 24-bit sensor
inputs, 32KB flash, 2KB RAM), evaluation board with application notes, energy
library and schematics. Features the next-generation MSP430i2040 ultra-lowpower metrology analog front end.
AMI Capability: RF interface: ZigBee®, wM-Bus/<1 GHz, Wi-Fi®/PLC via UART.
Software Features: 1-phase 0.5% energy library, anti-tampering.
Get Started: Contact TI representative
Support: MSP430 Energy Library at
www.ti.com/tool/msp430-energy-library
Metrology Front End
EVM430-Sub-Metering
Server Power, SinglePhase Metrology solution
Hardware based on the next-generation MSP430i2040, metrology analog
front end (4 SD24, 32KB flash, 2KB RAM), works across supply AC/DC input
90 – 220 VAC, 100 – 200 VDC.
Get Started: Contact TI representative
Software: Server power libary, power library for VRMS, IRMS, active, reactive
and apparent powers, THD for current/voltage, fundamental voltage/current,
Support: MSP430 Server Power Library
readings update every four AC cycles, capable of AC and DC supply measurement, Read white paper at www.ti.com/lit/slay020
automatic switching between AC and DC, EMI filter capacitor compensation
capabilities, no separate DC calibration required, serial port command reading and
calibration interface.
Metrology SoC
Class 0.5, Low-End
Single-Phase E-Meter SoC
Evaluation Module
(EVM430-FE4272)
Low-end single-phase, Class 0.5 electricity meter (32KB flash, 2 sigma-delta
sensor inputs + segment LCD) evaluation board. Comes with application notes,
energy library and schematics; features ultra-low-power MSP430FE4272
metrology SoC.
Get Started: Orderable at
www.ti.com/tool/evm430-fe4272
Support: Read white paper at
www.ti.com/lit/slaa203
Class 0.5, Low-End
Single-Phase E-Meter SoC
(+ Anti-Tamper) Evaluation
Module
(EVM430-FE427A)
Low-end single-phase, Class 0.5 electricity-meter plus anti-tamper (32KB flash,
3 sigma-delta sensor inputs + segment LCD) evaluation board with application
notes, energy library and schematics. Features MSP430FE427A ultra-low-power
metrology SoC.
Get Started: Orderable at
www.ti.com/tool/evm430-fe427a
Support: Read white paper at
www.ti.com/lit/slaa203
Class 0.1, Single-Phase
Smart E-Meter SoC
(+ Anti-Tamper +
Communication)
Evaluation Module
(EVM430-MSP430F6736)
Optimized smart meter SoC, Class 0.1 electricity meter (128KB flash, 8KB
RAM, 3 sigma-delta 24-bit sensor inputs, anti-tamper, 320-segment LCD +
communications ports). Support for CT/shunt.
AMI capability: RF interface: ZigBee, wM-Bus/<1 GHz, Wi-Fi/PLC via UART.
Software features: 1-phase 0.1% energy library, THD and fundamental, antitampering, temperature compensation and DLMS.
Get Started: Orderable at
www.ti.com/tool/EVM430-F6736
Support: Watch video at www.ti.com/f6736video
Metrology: Poly-Phase
Tool Identification
Description
Resources
Metrology SoC
Three-phase, Class 0.5 electricity meter plus anti-tamper (128KB flash, 3 sigmadelta sensor inputs + 160-segment LCD) evaluation board with application notes,
Class 0.5 Three-Phase
energy library and schematicsl. Features MSP430F67641.
SoC E-Metering Evaluation
AMI Capability: RF interface: ZigBee, wM-Bus/<1 GHz, Wi-Fi®.
Module (EVM430-F67641)
Software Features: 3-phase 0.1% energy library, THD and fundamental, antitampering, temperature compensation and DLMS.
Class 0.1 Three-Phase SoC
E-Meter (Anti-Tamper)
Evaluation Module
(EVM430-F47197)
Get Started: Orderable at
Three-phase electricity-meter, Class 0.1 with anti-tamper (120KB flash, 4KB RAM, www.ti.com/tool/evm430-f47197
7 sigma-delta 24-bit sensor inputs, 120-segment LCD controller) evaluation board Buy on TI e-store at www.ti.com/e-F47197
with application notes, software and schematics. Features MSP430F47197 ultraSupport: Read application report at
low-power metrology SoC.
www.ti.com/lit/slaa409
Three-phase electricity-meter, Class 0.1 with anti-tamper (512KB flash, 32KB
RAM, 7 sigma-delta 24-bit sensor inputs, 360-segment LCD controller) evaluation
Class 0.1 Three-Phase SoC
board with application notes, software and schematics. Features MSP430F6779
E-Meter (+ Anti-Tamper)
ultra-low-power metrology SoC.
evaluation module
AMI Capability: RF interface: ZigBee, wM-Bus/<1 GHz, Wi-Fi/PLC via UART.
(EVM430-F6779)
Software Features: 3-phase 0.1% energy library, anti-tampering, THD and
fundamental, temperature compensation and DLMS.
14
|
Smart Grid Solutions Guide 2014
Get Started: Contact TI representative
Support: MSP430™ Energy Library at
www.ti.com/tool/msp430-energy-library
www.ti.com/smartgrid
Get Started: Orderable at
www.ti.com/tool/EVM430-F6779
Contact TI representative
Support: Watch video at
www.ti.com/F6779
Texas Instruments
Smart Grid Development Tools
Flow Meter Solutions
Tool Identification
Description
Resources
SCAN IF Flow Meter
Scan-Interface-Based
Flow Meter
Features MSP430FW429, manual wheel spin to simulate flow rate, real-time
update to LCD and legacy design improved to showcase our scan interface.
Get Started: Sampling now
Contact TI representative
Support: www.ti.com/scan_interface
SCAN IF + FRAM Flow Meter
Scan Interface + FRAM
Flow Meter
Features MSP430FR689 based on FRAM device, uses enhanced scan interface to
measure flow, motor control board to simulate flow rate, real-time update to LCD Get Started: Sampling now
Contact TI representative
and RF modules.
Software Features: Extended scan-interface water measurement library for GMR, Support: www.ti.com/scan_interface
LC, optical sensor, integration to wireless M-Bus using CC1120 + Steinbeis stack.
Ultrasonic for Flow Meter
Ultrasonic Time Of Flight
Hardware Features: TPL7200 with discrete AFE + TDC + MCU and interface to
RF modules.
Software Features: Time-of-Flight technique and <100-ps resolution for
ultrasonic flow library.
Get Started: Sampling now
Contact TI representative
Support: www.ti.com/scan_interface
Power Line Communications (PLC)
Tool Identification
TMDSPLCKIT-V3 C2000™
Power Line Modem
Developer’s Kit
SOMPLC-PLC83 System
On Module (SOM) for
CENELEC Power Line
Communication (SFSK/
PRIME/G3/P1901.2)
SOMPLC-PLCM35 System
On Module (SOM)
for FCC Power Line
Communication (G3-FCC,
G3-ARIB, P1901.2 FCC)
Power Line
Communication
Docking Station
(TMDSPLCKIT-V4)
Description
Resources
The PLC developer’s kit enables easy development of software-based PLC
modems. The kit includes two PLC modems based on the C2000 TMS320F28069 Get Started: Orderable at
controlCARD™ and TI’s advanced PLC analog front end (AFE031). The included
www.ti.com/tool/tmdsplckit-v3
plcSUITE™ software supports several communication techniques, including OFDM
(PRIME/G3 and P1901.2) and is SFSK-capable. The kit includes onboard USB JTAG Support: www.ti.com/plc
emulation and Code Composer Studio™.
The SOMPLC-PLC83 is a self-contained hardware SOM for PLC that includes an
analog front end (AFE031) and a digital modem (F28PLC83) on one single PCB.
It is the ideal plug-in tool for developers to easily and quickly evaluate the most
popular narrowband CENELEC PLC standards like SFSK/PRIME/G3/P1901.2 in
their application environment. Plugs onto the TI PLC docking station.
Get Started: Orderable at www.ti.com/SOMPLC
Support: www.ti.com/plc
The SOMPLC-PLCM35 is a self-contained hardware SOM for PLC that includes
an analog front end (AFE032) and a digital modem (F28M35) on one single PCB.
The plug-in tool is for developers to easily and quickly evaluate the most popular
narrowband FCC PLC standards like G3-FCC, G3-ARIB, P1901.2 FCC in their
application environment. It also plugs onto the TI PLC docking station.
Get Started: Sampling now
Contact TI representative
Support: www.ti.com/plc
The TI PLC docking station is the new TI PLC kit compatible with CENELEC and
FCC PLC standards. Developers can plug TI PLC SOM modules to support the
various narrowband standards.
Hardware Features: Single hardware can support multiple modulation and
standards interface to RF modules to support ZigBee®, wM-Bus, Wi-Fi®, USB to
PC, RJ45 Ethernet connector.
Software Features: plcSUITE library, zero-configuration GUI, service-node
software for PRIME, G3, P1901.2. Up to FCC/ARIB bands, automated testing and
firmware upgrade.
Get Started: Sampling now
Contact TI representative
Support: www.ti.com/plc
TI Designs Reference
Design Library
www.ti.com/tidesigns
Texas Instrumentswww.ti.com/smartgrid
Smart Grid Solutions Guide 2014
|
15
Smart Grid Development Tools
Wireless Connectivity
Tool Identification
Description
Resources
Wide-Area Network
SimpleLink™
Sub-1-GHz PerformanceLine Development Kit
(CC1120DK)
Kit provides a complete hardware-performance-testing and software-development
Get Started: Orderable at
platform for TI’s sub-1-GHz performance-line devices. It can test power
www.ti.com/tool/cc1120dk
consumption and RF range/robustness with different settings (supports
868/915 MHz). Additional kits can be purchased separately to support other
Support: www.ti.com/lit/swru290
frequencies.
ZigBee® Home-Area Network
SimpleLink
CC2538 Development
Kit for ZigBee® and the
Internet of Things (IoT)
(CC2538DK)
SimpleLink
CC2530 Development Kit
(CC2530DK)
The CC2538DK development kit is a 2.4-GHz IEEE 802.15.4-compliant SoC
for ZigBee and the Internet of Things. The CC2538DK contains all hardware,
software, and tools necessary to build a 802.15.4-compliant product. It includes
CC2538-based evaluation modules, development boards, a USB interface dongle,
cables, antennas and documentation. It features a 2.4-GHz transceiver and ARM®
Cortex™-M3 MCU.
The CC2530DK development kit supports TI’s second generation 2.4-GHz IEEE
802.15.4-compliant SoC (CC2530) and contains all hardware, software and
tools necessary to build your 802.15.4-compliant product. It includes CC2530based evaluation modules, development boards, a USB interface dongle, cables,
antennas and documentation. The CC2530EM evaluation modules can be plugged
into SmartRF05EB boards, which are included.
Get Started: Orderable at
www.ti.com/tool/cc2538dk
Support: www.ti.com/lit/swrs096
Get Started: Orderable at
www.ti.com/tool/cc2530dk
Support: www.ti.com/lit/swrs081b
Secure Prepayment
RFID/NFC Transceiver
Evaluation Module Kit
(TRF7960AEVM/
TRF7970AEVM)
Self contained development platform which can be used to independently
evaluate/test the performance of the TRF7960A or TRF7970A RFID/near-fieldcommunications transceiver IC, custom firmware, customer designed antennas
and/or potential transponders for a customer defined RFID/NFC application.
TRF7970AEVM NFC Modes: Reader/writer, peer to peer and card emulation.
TRF7960AEVM NFC Modes: Reader/writer.
Get Started: Orderable at
www.ti.com/tool/trf7970aevm
Support: www.ti.com/lit/slos743
RF430CL330HTB
Target Board for NFC
Development
The RF430CL330H target board enables simplified BT + Wi-Fi® paring and the
evaluation of the dynamic NFC transponder with SPI/I2C interface for short-range
wireless communication with the NFC-enabled smart phones. The target board
also features an on-board PCB antenna and can be used with many different TI
microcontroller platforms.
Get Started: Orderable at
www.ti.com/tool/rf430cl330htb
Support: www.ti.com/lit/slas916a
The SimpleLink Wi-Fi CC3000 Booster Pack (CC3000BOOST) is an add-on board
designed to bring Wi-Fi to the MCU LaunchPad, based on TI’s SimpleLink Wi-Fi
CC3000 module. The CC3000 module enables simplified Wi-Fi connectivity for
Internet-of-Things MCU-based applications and comes with a full suite of support
tools. Additionally through its unique SmartConfig™ technology, the CC3000
delivers an easy one-click network set up for end-users. It is also compatible with
the MSP430 LaunchPad as well as the Tiva™ C Series TM4C123G LaunchPad.
Get Started: Orderable at
www.ti.com/msplaunchpad-cc3000boost
Contact TI representative
Support: www.ti.com/cc3000wiki
NFC Interface
Internet of Things (IoT)
MSP-EXP430G2CC3000BOOST –
SimpleLink™ Wi-Fi
CC3000 BoosterPack and
MSP430™ LaunchPad™
Bundle
16
|
Smart Grid Solutions Guide 2014
www.ti.com/smartgrid
Texas Instruments
Smart Grid Development Tools
Grid Infrastructure
Tool Identification
TMDSDC3359 Smart Data
Concentrator Evaluation
Module (EVM)
Description
Smart data concentrator evaluation module (EVM) with accompanying power
line communication (PLC) system-on-module and supporting software for smart
grid developers. Featuring the AM3359, the highly integrated TMDSDC3359
EVM provides the ultimate level of flexibility and scalability with numerous
performance, cost and connectivity options so developers can create dataconcentrator designs that can adapt to many worldwide smart grid standards
Hardware Support: Sitara™ AM335x processor with Cortex™ A8, interface to
all PLC SOM modules, interface to all RF modules (CC1101, CC1120, CC25xx),
Ethernet, USB and CAN.
Software Support: MAC layers and Library plcSUITE™, showcase a full network
solution, single base board offers multiple RF technologies and PLC standards,
usable for e-meter and flow meter networks, third party provides full DC solution.
PLC: PRIME, G3, P1901.2, PLC lite, proprietary
RF: ZigBee®, wM-Bus, Wi-Fi, 802.15.4g, proprietary
Resources
Get Started: Orderable at
www.ti.com/tool/TMDSDC3359
Support: Watch demo videos at
www.ti.com/dc_demo
Overview: www.ti.com/dc_overview
Smart Building/Internet of Things (IoT)
Tool Identification
Linux Based Gateway/
Smart Hub Reference
Design
Description
The IoT Gateway reference design creates a bridge between ZigBee® and Wi-Fi®
or Ethernet and enables applications such as real-time energy monitoring or
interaction with Wi-Fi-enabled smart appliances or smart plugs. It features the
AM3359 and aggregates data from wireless sensor networks and can provide
additional functions like security and monitoring. Additional communications
interfaces like NFC for smart phone pairing or prepayment and Bluetooth® can
also be used. The Linux®-based IoT Gateway manages communications, data
processing and applications locally instead of relying on intelligence in the cloud.
Hardware Support: Sitara™ AM335x processor with Cortex™ A8, TI ZigBee
CC2530 SoC, TI Combo Wi-Fi+ Bluetooth, TI NFC RF430 and interfaces available
for PLC.
Software Support: TI Linux SDK, TI Wi-Fi Drivers, TI ZigBee library (HA and SE
profile), TI NFC.
Resources
Get Started: Sampling today; schematics
available
Contact TI representative
Support: Watch video at
www.ti.com/solution/iot_gateway
Full System Solution Demo
Tool Identification
Smart Meter Board
(SMB)
Description
The SMB is a modular development platform incorporating key TI Smart Grid
devices to demonstrate the capabilities of a smart meter. SMB is a unique tool
with multiple features. It performs energy or electricity metering and has the
capability of transferring key metering data via PLC and wireless (Wi-Fi®, ZigBee®,
Sub-1 GHz) communication to showcase a simple automatic meter reading
(AMR) and automatic metering infrastructure (AMI) system. The development
platform takes advantage of TI Smart Grid software libraries to implement key
communication standards and typical utility-meter functions. A feature of the
platform is that the tool allows developers to choose the development tool
matching their project needs.
AMI: CC3000 for Wi-Fi, CC2530 for ZigBee and SE 1.x, CC2538 for ZigBee IP and
SE2.0, TRF7970 for NFC and C2000™ for PLC.
Resources
Get Started: www.ti.com/smartgrid
Contact TI representative for demonstration
Support: Watch video at
www.ti.com/smb3
TI Designs Reference
Design Library
www.ti.com/tidesigns
Texas Instrumentswww.ti.com/smartgrid
Smart Grid Solutions Guide 2014
|
17
Smart Grid Solutions www.ti.com/smartgrid
Today’s solutions for tomorrow’s power
infrastructure and industrial energy systems
• Grid Infrastructure
• Smart Meters for Electricity, Gas, Water and Heat
• Smart Energy Management for Homes and Buildings
• Wired and Wireless Communication
The power of TI saves you time to market.
• Globally deployed metering know-how and products
• Comprehensive end-to-end System-on-Chip (SoC) solutions
• Innovation and expertise across a robust portfolio
Speed your design cycle with TI’s flexible solutions.
• Hardware, software and SoCs tailored to functional
requirements
• Upgradable, in-system programmable flash memory to
support evolving worldwide standards
• Available standards include IEC, ANSI, ZigBee®,
Wireless M-Bus (wM-Bus), PLC and 6LoWPAN
• Scalable for optimization of system requirements
and future deployments
Outsmart the competition with smarter solutions.
• Optimized electricity-meter SoC (MSP430™)
• Flexible applications-processor SoC (LM4F1x)
• Dedicated MCU peripheral for flow meter rotation detection
• High performance for graphical user interfaces (Sitara™ AM335x
MPU and LM4F1x)
• Optimized, low-power radio SoC (CC1101/CC1120 ISM)
• Flexible power line communication processors (TMS320F28PLCxx)
• Secure RFID and NFC prepayment options (TRF79xx, TMS37xx)
• Complementary interface and power management
• Cost-effective integration and volume manufacturing
• Compliance with wM-Bus and
802.15.4g
• Compliance with future worldwide security requirements
• Multiple Wi-Fi® offerings from
easy configuration, extended range, more throughput
and simultaneous streaming
(CC3000, WL18xx modules)
TI Worldwide Technical Support
Internet
Asia
TI Semiconductor Product Information Center Home Page
support.ti.com
TI E2E™ Community Home Page
e2e.ti.com
Product Information Centers
Americas
Brazil
Mexico
Phone
+1(512) 434-1560
Phone0800-891-2616
Phone0800-670-7544
Fax
+1(972) 927-6377
Internet/Emailsupport.ti.com/sc/pic/americas.htm
Europe, Middle East, and Africa
Phone
European Free Call
00800-ASK-TEXAS
(00800 275 83927)
International
+49 (0) 8161 80 2121
Russian Support
+7 (4) 95 98 10 701
Note: The European Free Call (Toll Free) number is not active in all c­ ountries.
If you have technical difficulty calling the free call number, please use the i­nternational
number above.
Fax
+(49) (0) 8161 80 2045
Internetwww.ti.com/asktexas
Direct Email
[email protected]
Japan
PhoneDomestic 0120-92-3326
Fax
International+81-3-3344-5317
Domestic0120-81-0036
Internet/Email
Internationalsupport.ti.com/sc/pic/japan.htm
Domesticwww.tij.co.jp/pic
© 2014 Texas Instruments Incorporated
Printed in U.S.A. by (Printer, City, State)
Phone
International +91-80-41381665
Domestic
Toll-Free Number
Note: Toll-free numbers do not support mobile and IP phones.
Australia 1-800-999-084
Malaysia 1-800-80-3973
China
800-820-8682
New Zealand0800-446-934
Hong Kong 800-96-5941
Philippines 1-800-765-7404
India
1-800-425-7888
Singapore 800-886-1028
Indonesia 001-803-8861-1006 Taiwan
0800-006800
Korea
080-551-2804
Thailand 001-800-886-0010
Fax+8621-23073686
[email protected] or [email protected]
Internetsupport.ti.com/sc/pic/asia.htm
Important Notice: The products and services of Texas Instruments Incorporated and
its subsidiaries described herein are sold subject to TI’s standard terms and conditions
of sale. Customers are advised to obtain the most current and complete information
about TI products and services before placing orders. TI assumes no liability for
applications assistance, customer’s applications or product designs, software
performance, or infringement of patents. The publication of information regarding any
other company’s products or services does not constitute TI’s approval, warranty or
endorsement thereof.
B011314
The platform bar, C2000, Code Composer Studio, controlCARD, D-CAP2, DCS-Control, DSP/
BIOS, E2E, Eco-mode, LaunchPad, MSP430, OMAP, Piccolo, plcSUITE, SimpleLink, Sitara,
SmartConfig, Tiva, Tivaware, WiLink and Z-Stack are trademarks of Texas Instruments. The
Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc., and any use of
such marks by Texas Instruments is under license. Android is a registered trademark of
Google, Inc. ARM9 and Cortex are trademarks and ARM is a registered trademark of ARM
Limited. Linux is a registered trademark of Linus Torvalds. MIFARE is a trademark of NXP
Semiconductors. Wi-Fi is a registered trademark of the Wi-Fi Alliance. ZigBee is a
­registered trademark of the ZigBee Alliance. All other trademarks are the property of their
respective owners.
SLYM071N
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement