Teldat bintec WI1040n Datasheet

Add to my manuals
9 Pages

advertisement

Teldat bintec WI1040n Datasheet | Manualzz

Industry access point

bintec WI1040n

• WLAN according IEEE 802.11n, compatible with .11agbh

• With one radio module, dual band radio

• Operation as access point, bridge, WDS, client

• PoE, optional with fiber optic WAN interface

• Protection class IP40, extended temperature operating

• Approval for usage in vehicles (E1)

bintec WI1040n

Industry access point

The WI1040n is an industrial (IP40) 11n access point with a dual-band radio module. The stable, dustproof metal housing and large operating temperature range allow the device to be used under extreme environmental conditions.

Product description

Power supply optionally via 24V DC or PoE

WAN optionally via Ethernet or optical fiber cable

Tested to EN50121 for operation in railroad vehicles

Operation is medical institutions permissible in accordance with

EN60601

Operation as fat AP or as controller based AP via bintec WLAN controller

The bintec WIx040n series devices are industry-proof access points with protection class IP40, which can be deployed in industry or other harsh application scenarios. The stable, dustproof metal casing and the wide temperature range also allow deployment under extreme environmental conditions. Depending on the model, the devices have one or two IEEE 802.11agbn standard wireless modules and allow PHY rates of up to 300 Mbps per wireless module.

WIx040n for wireless networking of moving machines Besides the access point mode, the

WIx040n can also be operated as a WLAN client. In this mode you can connect machines and devices wireless to your infrastructure. Here it is irrelevant whether your machines have an

Ethernet or a serial interface. The bintecWIx040n devices support both connection options.

WIx040 in vehicles

The E1 approval provided means that the WIx040 series devices may be installed in vehicles and powered directly from the vehicle’s 24 Volt on-board network. Numerous applications arise in public transportation for example – from updating passenger information through to automatic exchange of passenger data on entry in the bus depot or on arrival at stops.

WIx040n in warehouse management

If you have to supply a large warehouse with WLAN, e.g. to connect your wireless hand scanner to your enterprise resource management system, the bintec WIx040n series devices help you overcome many obstacles.

In this scenario and in conjunction with sound wireless cell planning, the WI devices’ IAPP protocol provides for optimized roaming behavior of the terminal devices. The optional optical fiber WAN interface spans up to 2 km thus also allowing access points at remote parts of the plant site to also be operated.

Management

Here you have the choice between several solutions.

To configure individual devices you only need you Internet browser. The web server integrated in the device allows fast configuration and monitoring via the graphical user interface.

Teldat GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany

Phone: +49 - 911 9673-0 - Telefax: +49 - 911 688 07 25

E-Mail: [email protected] - www.teldat.org

bintec WI1040n

11.12.2013

Subject to technical alterations

Page 2 / 9

For larger installations, the complimentary DIME Manager assists in automatically finding unconfigured devices in the network and enables specific configuration of devices.

WLAN Controller

Optimize your WLAN network by using a bintec WLAN controller. The bintec WLAN controller allows configuration of your customers WLAN network in lesser than 30 minutes ... and this without deeper WLAN know-how! The automatic RF management system relieves you the time killing search for free WLAN channels and selects the best channels for the system.

For smaller WLAN networks up to 6 APs bintec access points (W1002n,

WI series) are able to take over the function of the WLAN controller by themself and work as quasi master APs. For networks with more than 6 up to 72 APs you will need a bintec R1202 as WLAN controller hardware. You are able to manage bigger WLANs with up to 150 AP by using a bintec RXL12x00 as WLAN controller hardware.

Variants

bintec WI1040n (5010590006) Ruggedized .11a/b/g/h/n indoor WLAN Accesspoint/Bridge/Client, single radio, 3

RTNC antennas, 2xEth, 1xSFP, 1 x serial, 1 x relay, IP 40, power supply not included in delivery

Features

Operation Modes

WLAN disabled

WLAN access point

WLAN bridge

WLAN client

In this operation mode the device is a powerful 2-port VPN router

WLAN access point with VPN router functionalities

Point-to-point and point-to-multipoint mode (up to 8 links)

Transparent client for direct connection of Ethernet devices

Wireless LAN

WLAN standards

Frequency bands 2.4 GHz indoor/outdoor (EU)

Frequency bands 5 GHz indoor

(EU)

802.11n (Mimo 2x3); 802.11b; 802.11g; 802.11a; 802.11h

2.4 GHz Indoor/Outdoor (2412-2472 MHz) max. 100 mW EiRP. This information is related to the permitted transmission power in Germany. The permitted transmission power may vary in other countries.

5 GHz indoor (5150-5350 MHz) max. 200 mW EiRP allowed. This information is related to the permitted transmission power in Germany. The permitted transmission power may vary in other countries.

Teldat GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany

Phone: +49 - 911 9673-0 - Telefax: +49 - 911 688 07 25

E-Mail: [email protected] - www.teldat.org

bintec WI1040n

11.12.2013

Subject to technical alterations

Page 3 / 9

Wireless LAN

Frequency bands 5 GHz outdoor

(EU)

Frequency bands 5.8 GHz BFWA

(Germany)

WLAN modes

Automatic Rate Selection (ARS)

Transmission rate

Data rates for 802.11b,g (2.4

GHz)

Data rates for 802.11a,h (5 GHz)

Data rates for 802.11n (2.4 / 5

GHz)

Receiver Sensitivity @ 2.4 GHz

802.11b/g

Receiver Sensitivity @ 2.4 GHz

802.11n 20 MHz

Receiver Sensitivity @ 2.4 GHz

802.11n 40 MHz

Receiver Sensitivity @ 5 GHz

802.11a/h

Receiver Sensitivity @ 5 GHz

802.11n 20 MHz

Receiver Sensitivity @ 5 GHz

802.11n 40 MHz

Output power (without antenna gain)

Tx Power @ 2.4 GHz 802.11b/g

Tx Power @ 2.4 GHz 802.11n 20

MHz/40 MHz

5 GHz outdoor (5470-5725 MHz) max. 1000 mW EiRP allowed. This information is related to the permitted transmission power in Germany. The permitted transmission power may vary in other countries.

5.8 GHz BFWA (5755-5875 MHz) max. 4000 mW EiRP allowed. This information is related to the permitted transmission power in Germany. For the usage in other countries, please contact the location regulation authorities.

2.4 GHz operation: 802.11b only; 802.11g only, 802.11b/g/n mixed; 802.11b/g/n mixed long;

802.11b/g/b mixed short; 802.11b/g/n; 802.11g/n; 802.11n only; 5 GHz Operation: 802.11a only;

802.11a/n; 802.11n only

Available

Automatic fallback or fixed transmission rate selectable

11, 5.5, 2 und 1 Mbps (DSSS modulation); 54, 48, 36, 24, 18, 12, 9 and 6 Mbps (OFDM modulation)

54, 48, 36, 24, 18, 12, 9 and 6 Mbps (OFDM modulation)

MSC0-15 enables physical rates up to 150 Mbps at 20 MHz channels bandwidth, 2 streams, short guard interval; MSC0-15 enables physical data rates up to 300 Mbps at 40 MHz channels bandwidth, 2 streams, short guard interval

1 Mbps -91 dBm; 2 Mbps -90 dBm; 5.5 Mbps -89 dBm; 11 Mbps -88 dBm; 6 Mbps -90 dBm;9 Mbps

-89 dBm; 12 Mbps -88 dBm; 18 Mbps -86 dBm; 24 Mbps -83 dBm; 36 Mbps -80 dBm; 48 Mbps -76 dBm; 54 Mbps -74 dBm

MSC0 -89 dBm; MSC1 -87 dBm; MCS2 -85 dBm; MCS3 -82 dBm; MCS4 -79 dBm; MSC5 -75 dBm;

MCS6 -73 dBm; MCS7 -70 dBm; MCS8 -83 dBm; MCS9 -84 dBm; MCS10 -81 dBm; MCS11 -79 dBm;

MCS12 -80 dBm; MCS13 -72 dBm; MCS14 -68 dBm; MCS15 -67 dBm

MSC0 -87 dBm; MSC1 -84 dBm; MCS2 -82 dBm; MCS3 -79 dBm; MCS4 -75 dBm; MSC5 -71 dBm;

MCS6 -69 dBm; MCS7 -67 dBm; MCS8 -86 dBm; MCS9 -83 dBm; MCS10 -79 dBm; MCS11 -77 dBm;

MCS12 -74 dBm; MCS13 -69 dBm; MCS14 -67 dBm; MCS15 -65 dBm

6 Mbps -88 dBm; 9 Mbps -87 dBm; 12 Mbps -86 dBm; 18 Mbps -84 dBm; 24 Mbps -82 dBm; 36

Mbps -78 dBm; 48 Mbps -74 dBm; 54 Mbps -73 dBm

MSC0 -88 dBm; MSC1 -85 dBm; MCS2 -83 dBm; MCS3 -81 dBm; MCS4 -78 dBm; MSC5 -74 dBm;

MCS6 -72 dBm; MCS7 -70 dBm; MCS8 -88 dBm; MCS9 -85 dBm; MCS10 -83 dBm; MCS11 -80 dBm;

MCS12 -77 dBm; MCS13 -72 dBm; MCS14 -70 dBm; MCS15 -68 dBm

MSC0 -84 dBm; MSC1 -82 dBm; MCS2 -79 dBm; MCS3 -77 dBm; MCS4 -74 dBm; MSC5 -69 dBm;

MCS6 -67 dBm; MCS7 -66 dBm; MCS8 -83 dBm; MCS9 -82 dBm; MCS10 -79 dBm; MCS11 -76 dBm;

MCS12 -72 dBm; MCS13 -68 dBm; MCS14 -66 dBm; MCS15 -64 dBm

Adjustable in following steps: 5, 8,11,14,16 und 17.5 dBm. Maximal power varies depending on data rate and frequency band.

1 Mbps 16 dBm; 2 Mbps 16 dBm; 5.5 Mbps 16 dBm; 11 Mbps 16 dBm; 6 Mbps 17,5 dBm; 9 Mbps

17,5 dBm; 12 Mbps 17 dBm; 18 Mbps 17 dBm; 24 Mbps 15 dBm; 36 Mbps 15 dBm; 48 Mbps 13 dBm; 54 Mbps 13 dBm

MSC0 17.5 dBm; MSC1 17,5 dBm; MCS2 17 dBm; MCS3 17 dBm; MCS4 15 dBm; MSC5 15 dBm;

MCS6 13 dBm; MCS7 13 dBm; MCS8 17.5 dBm; MCS9 17.5 dBm; MCS10 17 dBm; MCS11 17 dBm;

MCS12 15 dBm; MCS13 15 dBm; MCS14 13 dBm; MCS15 13 dBm

Teldat GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany

Phone: +49 - 911 9673-0 - Telefax: +49 - 911 688 07 25

E-Mail: [email protected] - www.teldat.org

bintec WI1040n

11.12.2013

Subject to technical alterations

Page 4 / 9

Wireless LAN

Tx Power @ 5 GHz 802.11b/g

Tx Power @ 5 GHz 802.11n 20

MHz/40 MHz

Number of spatial streams

(802.11n)

Bandwidth (802.11n)

Short guard interval (802.11n)

DTIM Period

Multi SSID

Broadcast SSID

Clients (Pwr. Managmt./max number)

Country-specific settings

TPC

DFS

RTS/CTS

1 Mbps 16 dBm; 2 Mbps 16 dBm; 5.5 Mbps 16 dBm; 11 Mbps 16 dBm; 6 Mbps 17.5 dBm; 9 Mbps

17.5 dBm; 12 Mbps 17 dBm; 18 Mbps 17 dBm; 24 Mbps 15 dBm; 36 Mbps 15 dBm; 48 Mbps 13 dBm; 54 Mbps 13 dBm

MSC0 17.5 dBm; MSC1 17.5 dBm; MCS2 17 dBm; MCS3 17 dBm; MCS4 15 dBm; MSC5 15 dBm;

MCS6 13 dBm; MCS7 13 dBm; MCS8 17.5 dBm; MCS9 17.5 dBm; MCS10 17 dBm; MCS11 17 dBm;

MCS12 15 dBm; MCS13 15 dBm; MCS14 13 dBm; MCS15 13 dBm

1 or 2

20/40 MHz (bundling of two adjoining 20 MHz channels to one 40 MHz channel)

On/off switchable; increase of throughput by reduction of the guard intervals from 800ns to 400ns

Adjustable

Depending on the complexity of configuration up to 8 service sets per radio module, with virtual access points and own MAC address per SSID.

On/off switchable

Registering of up to 250 clients per radio module simultaneously in access point mode. Default value is 32 clients.

Channel settings according regulatory domain (802.11d) permitted.

TPC (transmission power control): For 5 GHz, automatic reduction of transmission power according

EN301893

DFS (dynamic frequency selection): For 2.4 and 5 GHz, channels are dynamically used depending on operating grade. DFS is implemented in bridge links master and slave.

RTS/CTS threshold adjustable

Security

Encryption WEP/WPA

IEEE802.11i authentication and encryption

Access control list (ACL)

VLAN

Inter cell repeating

NAT/PAT

VPN - IPSec

VPN - IPSec

VPN - IPSec DPD

VPN - PPTP

WEP64 (40 Bit key), WEP128 (104 Bit key), WPA personal, WPA enterprise, WPA2 personal, WPA2 enterprise

802.1x/EAP-MD5, 802.1x/EAP-TLS, 802.1x/EAP-TTLS, 802.1x/EAP-PEAP, key management, PSK/TKIP encryption, AES encryption, 802.1x/EAP

MAC address filter for WLAN clients

Network segments on layer2 possible. Per SSID one VLAN ID available. Static VLAN configuration according IEEE 802.1q; up to 32 VLANs supported.

Inter traffic blocking for public hot spot (PHS) applications for preventing of communication radio client to radio client in a single radio cell.

Network & Port Address Translation / Stateful Packet Inspection: Isolation of complete network from public access

10 tunnels inclusive, 100 more via separate license

Powerful encryption up to 256 bits (AES, 3DES, DES, CAST, Blowfish, Twofish)

Dead Peer Detection for IPSec tunnels

Integrated

Teldat GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany

Phone: +49 - 911 9673-0 - Telefax: +49 - 911 688 07 25

E-Mail: [email protected] - www.teldat.org

bintec WI1040n

11.12.2013

Subject to technical alterations

Page 5 / 9

Security

VPN - PPTP

DynDNS / DynVPN

IKE for IPSec

X.509

QoS for IPSec

PKI Support for IPSec

NAT Traversal for IPSec

IPCOMP

IPSec / RADIUS

IPSec redesign

L2TP

GRE

Hardware encryption

Strong encryption up to 128 bits (MPPE), up to 168 bits (DES/3DES, Blowfish)

Router can still be reached over the Internet in spite of dyn. IP address

Pre-Shared Keys and X.509 certificate support

X.509 v1/v3 certificates (PKCS#7/8/10, 12, CLRs, SCEP)

Available

Available

Available

IP compression

Available

Policy manager and interface concept

Layer 2 tunnelling protocol for ATM, Ethernet, PPP; user authentication

V.0 according RFC 2784 for common encapsulation

3DES, AES and RC4

Software

Roaming (access point mode)

Fast roaming 802.1x (access point mode)

Roaming behaviour (client mode)

WDS

Bridge: point-to-point / point-to-multipoint

Bridge

Bridge link test

Bridge link encryption

Client mode

Buffer pool

WMM 802.11e QoS

WMM Power Save (U-APSD)

Internet dialup

Load balancing

Seamless roaming with IAPP (artem Inter Access Point Protocol)

Pre authentication and PMK caching allows fast roaming by 802.1x encryption

Adjustable (no, slow, normal, fast, customized roaming). Adaptable for fast movable client (i.e.

vehicle), to guarantee a roaming without interruption. This is achieved by scanning of the relevant channels in the background.

Wireless Distribution System: Include high security TKIP and AES, interoperable with W1002n,

WIx40, WIx65n, RS120wu, RS232aw, RS232bw and RS232jw

Point-to-point connection between two access points, point-to-multipoint connection between up to eight partners access points

Full remote configuration: Protocol with encrypted transmission. RTS/CTS threshold adjustable.

Operating channels: According to the regulatory domain. Transmit speed: Auto fallback or selectable fixed rate.

Via the link test the quality of a bridge link can be measured.

With high security TKIP and AES possible

Routing or bridge mode possible. In bridge mode multiple IP based end devices can be operated simultaneously and additionally one non-IP-based end device

For cushioning of peaks

Data prioritization for TOS data, 802.11e/WMM

Support of active WLAN clients, which support 802.11e power save

PPPoE, PPTP

Session-round-robin, load-dependent bandwidth

Teldat GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany

Phone: +49 - 911 9673-0 - Telefax: +49 - 911 688 07 25

E-Mail: [email protected] - www.teldat.org

bintec WI1040n

11.12.2013

Subject to technical alterations

Page 6 / 9

Software

BLD

NTP

DNS

DHCP

Broken Link Detection (BLD) per SSID possible.

NTP client, NTP server, manually

DNS client, DNS server, DNS relay

DHCP client, DHCP server, DHPC relay

Maintenance

Configuration a. maintenance:

Device configuration via

Configuration a. maintenance:

SNMP

Configuration a. maintenance:

SNMP configuration

Configuration a. maintenance:

SSH Login

Configuration a. maintenance:

HTTP/HTTPS

Configuration a. maintenance:

Secure configuration

Configuration a. maintenance:

Configuration export and import

Configuration a. maintenance:

On the fly configuration

Configuration a. maintenance:

Software update

External reporting: Syslog

External reporting: eMail alert

External reporting: SNMP traps

External reporting: Activity monitor

Monitoring: Internal Log

Monitoring: IPSec

Monitoring: Interfaces

Monitoring: WLAN

Monitoring: Configurable scheduler

Telnet, SSH, HTTP, HTTPS, SNMP

SNMP (v1, v2, v3), USM model, VACM views, SNMP traps (v1, v2, v3) configurable, SNMP IP access list configurable

Complete management with MIB-II, MIB 802.11, enterprise MIB

Supports SSH V1.5 and SSH V2.0, for secure connections of terminal applications

Web-based configuration (FCI). The user interface is identical with almost all bintec elmeg products.

SSH available, HTTPS, Telnet protected against 'bruce force attacks'

Load and save of configurations; save configuration optionally encrypted; optional, automatic controlled via scheduler

No restart is required after the configuration has been changed.

Software updates free of charge; loadable via file, HTTP or via direct access to the bintec elmeg server; optional, automatic controlled via scheduler

Syslog client, with different levels of messaging.

Automatic eMail alert by definable events

Supported

Sending of information to a PC on which Brickware is installed

Output via web-based configuration interface (http/https); filter: subsystem, level, message

Displayed: IPSec tunnels and IPSec statistics; output via web-based configuration interface

(http/https)

Statistic information of all physical and logical interfaces (ETH0, ETH1, SSIDx, ...)

Detailed displays for radio, VSS, WDS link, bridge links, client links. Displayed are per link: MAC address, IP address, TX packets, RX packets, signal strength for every receiving aerial, signal-to-noise ratio, data rate

Following events can be scheduled: Reboot device, activate/deactivate interface, activate/deactivate WLAN, initiate 5 GHz band scan, trigger SW update, trigger configuration backup

Teldat GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany

Phone: +49 - 911 9673-0 - Telefax: +49 - 911 688 07 25

E-Mail: [email protected] - www.teldat.org

bintec WI1040n

11.12.2013

Subject to technical alterations

Page 7 / 9

Maintenance

Management: Supported management systems

Management: Discovery function bintec WLAN Controller, DIME Manager, XAdmin

Management: Discovery Protocol

Documentation

Guarantee

Protocols: Madge Discovery Protocol (MDP), bintec elmeg discovery protocol (ADP), works also across subnets

CAPWAP DHCP option according RFC1517

German and English documentation on CD and in the Internet for download

2-year manufacturer's guarantee, Online RMA handling

Hardware

Certifications

Standards and certifications

Medical standards and certifications (only WIx040n)

Railway and automotive standards and certifications

(only WIx040n)

Wifi Certification

LAN / WAN

Optical WAN/LAN Interface

Serielle Schnittstelle

WAN

Antenna

Temperature Sensor

Alarm relay

Real time clock

Power supply

PoE

Status LEDs

Montage

Theft protection

Protection class

Dimensions

Weight

Wi-Fi Certified according 802.11abgn (Rel.7.9.4)

R&TTE Directive 1999/5/EG; EN 60950-1 (IEC60950); EN 60950-22; EN 301489-1; EN301489-17; EN

55022; EN 300328-1; EN 301893; EN 302502; EN 50371

EN 60601-1; EN 60601-2; EN 55011

EN 50121-3-2; ISO 7637-1; ISO 7637-2, E1-mark

Wifi Certified product according IEEE 802.11abgn under preparation

2 x 10/100 Mbps Ethernet twisted pair, autosensing, auto MDI/MDI-X

SFP slot for 100 Mbps Fibre Transceiver. Only one ETH interface is activated, if SFP module is plugged

V.24 interface with D-Sub9 jack for configuration and for data transmission over IP

IEEE 802.11a/b/g/n; 1 radio module, 2.4 und 5 GHz band, 3 external antennas

Three antenna connectors with RTNC jacks; delivered incl. three 2 dBi omni-directional antennas

Temperature supervision and software controlled interaction. Controlling of the radio module heading at temperature below -10°C.

Controlled by software i.e. for alarm, overtemperature, undertemperature; 1A 42V AC / 2A 30V DC

Even at power loss the system time will be available for several hours.

Power requirements: 24V +/-30% max. 1 A; Operation with two redundant power supplies supported; Operation is indepent of the Polarity of the power supply; Power supply unit is not include in the delivery

Power-over-Ethernet according IEEE 802.3af

Status + activity for WLAN, Ethernet 1, Ethernet 2; SFP, Failure

Wall mounting include; DIN Rail mounting as an option available

Theft protection optional available

IP40 protected for indoor usage

215mm x 40mm x 165mm (width x height x depth)

Approx. 1200g

Teldat GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany

Phone: +49 - 911 9673-0 - Telefax: +49 - 911 688 07 25

E-Mail: [email protected] - www.teldat.org

bintec WI1040n

11.12.2013

Subject to technical alterations

Page 8 / 9

Hardware

Environment Temperature operating: -25°C to +65°C; storage: -40°C to 85°C; rel. humidity 10 to 95% (non condensing)

Accessoires

Industry Products

bintec WI-Client (5510000169) WLAN Client adaptor for industrial applications, IEEE802.11a/b/g/h, 1 x ETH, RS232 data interface. 2 ext. RSMA antenna sockets, WPA, WPA2, 802.1x, 2 x standard omni antennas, DIN-Rail and wall mounting

WLAN Controller

WI-License WLAN Contr. 6AP (5500000942) WI series license WLAN Controller for 6 AP

Pick-up Service / Warranty Extension

Service Package 'large' (5500000811) Warranty extension of 3 years to a total of 5 years, including advanced replacement for Teldat products of the category 'large'. Please find a detailed description as well as an overview of the categories on www.teldat.de/servicepackages.

Antennas, Cables and Adapters

Module SFP-100 (5510000163) SFP-100 Module Fiber extension for WI-Series; multimode, extended temperature range

Add-ons

Ascom i62 VoWiFi Basic Talker

(5530000044)

Theft Protection WI-40 Series (5020590400)

DIN Rail adaptor WI-40 Series (5000592600) i62 VoWifi telephone, 802.11abgn, battery included, 18 months warranty

Anti-Theft Protection and Wall Mounting Kit for WI-40 Series APs

DIN Rail adaptor for WI-40 Series

Teldat GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany

Phone: +49 - 911 9673-0 - Telefax: +49 - 911 688 07 25

E-Mail: [email protected] - www.teldat.org

bintec WI1040n

11.12.2013

Subject to technical alterations

Page 9 / 9

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement