LIBRARY of Shampoo Bowl Parts

LIBRARY of Shampoo Bowl Parts
Fixtures - Parts - Accessories to shampoo bowls
Page 1
??? - For what brand of bowl do you need parts ???
Find out by looking on the bottom of the bowl, between the front and strainer,
where molded in the bottom is the brand and model number. For example,
"Marble Products #10"
*******************************************
Belvedere
*******************************************
622c Fixture
by Belvedere
Can be used also to replace the #112 two handle fixture that
came with Belvedere Shampoo Bowls for years prior to 1990.
The # 112 fixture is discontinued but we have most parts
available as seen below.
Note:
If you are replacing a 2-handle fixture with the 622c,
then you may want to purchase the Cover Plate below to
Notice to Plumbers:
The OD diameter of the treads at the
point that this fixture goes through the
shampoo bowl is 1-1/8 inch
*******************************************
Fixtures - Parts - Accessories to shampoo bowls
Page 2
Handle for Belvedere #622c Single Lever
Fixture
* Handle Only *
* Replacement Handle for Belvedere # 622TC Single Handle
Fixture
* Crystal Clear Plastic Handle
* "Tear Drop Shape" when looking down from top
* Includes: Handle Cover, Handle Screw, Handle Washer and
Handle
******************************************
Flo-Temp Cover Plate
by Belvedere
Use with #622c and #528 Fixture
Includes:
1112-
Cover Plate
Gasket
Mounting Bracket
Screws
Place the Flo-Temp cover plate and gasket over
the 2 left-hand holes in the bowl fixture deck.
Then attach the mounting bracket on the bottom
side of the bowl with the 2 mounting screws
included.
*******************************************
Fixtures - Parts - Accessories to shampoo bowls
Page 3
622c Cartridge
by Belvedere
The only replacement part for the 622c Fixture
comes with clip as shown
*******************************************
522 Fixture
by Belvedere
Deck Mount Fixture
z
Chrome
z
Single Handle Control
z
Replacement Cartridge
sold below
Will NOT fit older Belvedere Bowls, Please See
the #622c (sold above) as a replacement fixture.
May Need Cover Plate for 2 of the 3 Holes in Bowl
(Sold Above)
*******************************************
Fixtures - Parts - Accessories to shampoo bowls
Page 4
*******************************************
528 Fixture with Spout
by Belvedere
Deck Mount Fixture
z
Fits Belvedere Bowls.
z
NEW! Deck Mount Fixture By BELVEDERE,
Chrome, Single Handle Control with Diverter
Spout
* Fits Belvedere Bowls.
* May Need Cover Plate for 2 of the 3 Holes in
Bowl * Sold Separately above.
* This Fixture Replaces the Discontinued 2
handle with Diverter Spout # 4228P Fixture
Replaces the Discontinued #4228P Spout Fixture
*******************************************
Fixtures - Parts - Accessories to shampoo bowls
Page 5
Vacuum Breaker
by Belvedere
# 403
Fits Only Belvedere Bowls
This is a one way valve that saves the
integrity of the fresh water system by NOT
allowing contaminate water (water
contaminated with perm solution,
neutralizer, hair color, etc.) from mixing
with the fresh water system that we drink.
Material: Plastic Plumbing Code: ASSE
#1001
Consult your local plumber and building
codes for need of this product.
*******************************************
Vacuum Breaker * ONLY
by Belvedere
# 403
Fits ONLY Belvedere Bowls
Includes: Vacuum Breaker only
* Material: Plastic
* Plumbing Code ASSE # 1001
* Shampoo Hose is sold separately.
This is a one way valve that saves the integrity of the
fresh water system by not allowing contaminate water
( water contaminated with perm solution, neutralizer,
hair color and etc.) from mixing with the fresh water
system that we all drink.
Consult your local plumber and building codes for
need of this product.
Fixtures - Parts - Accessories to shampoo bowls
Page 6
Hose Receiver Kit for Vacuum Breaker
by Belvedere
* Fits Belvedere Shampoo Bowls
* Vacuum Breaker Shampoo Hose Receiver
* Has 2 - 1/2" holes to the Left of the Hose Opening to
accommodate
Belvedere Vacuum Breaker's #403 or #503
* Complete with Clamp (Steel square and 4 screws) and Gasket
* Chrome (Plastic)
* Dimension of Receiver 2-7/8" x 2-5/8"
*******************************************
LA, CA Vacuum Breaker #503C
by Belvedere
This vacuum breaker is a MUST for areas below:
Oregon state, Wisconsin State, and Los Angeles County, CA
Includes: #503 Vacuum Breaker, Hose Receiver, and Hose from
Fixture to Breaker
* ASSE 1014 Approved
* Dimension of Receiver 2-7/8" x 2-5/8"
* Shampoo Hose is sold separately.
This is a one way valve that saves the integrity of the fresh
water system by Not allowing contaminate water ( water
contaminated with perm solution, neutralizer, hair color and
etc.) from mixing with the fresh water system that we all drink.
Consult your local plumber and building codes for need of this
product.
* Replaces #404 Vacuum Breaker *
*******************************************
Fixtures - Parts - Accessories to shampoo bowls
Page 7
Hose Receiver Kit * Plain
by Belvedere
* Plain Shampoo Hose Receiver * NOT for Vacuum Breaker
* Fits Belvedere Shampoo Bowls Only
* Complete with Clamp (Steel square and 4 screws) and Gasket
* Chrome (Plastic)
* Dimension of Receiver 2-7/8" x 2-5/8"
Whiz Spray Hose
by Belvedere
screws on to fixture
Length: 42 inches
*******************************************
Fixtures - Parts - Accessories to shampoo bowls
Page 8
Seats
by Belvedere
Fits # 112 Fixture
package contains: 2-brass seats
*******************************************
Gland Assemblies
by Belvedere
Fits # 112 Fixture
*** No Longer Available ***
package contains: 1-hot and 1-cold Gland Assemblies
*******************************************
Complete Strainer Assembly
by Belvedere
3-1/2"
The smaller 1-1/2" strainer assembly has been discontinued.
Package includes strainer cup ( 1 ) and items ( 2 ) thru ( 8 ) as
shown in illustration.
*******************************************
Strainer
by Belvedere
3-1/2"
Plastic strainer cup only
*******************************************
Fixtures - Parts - Accessories to shampoo bowls
Page 9
Mounting Bracket
Fits most Belvedere Bowls
(#3800, 3100, 8000, 8100, 8200, 9000, & 1980W)
&
Marble Products Fiber Glass Bowls #10 and #30
Bracket has 2 slots to accommodate 2-tongues on Back of
Bowl that is Parallel to Wall. Tongues are 9" Center
Package contains: Metal Bracket and 1-Camber Bolt
usually mounted with 4 wood screws ( not included )
Note: #3100 bowl needs shorter leveling bolt which is not included, but may be
*******************************************
Shampoo Bowl Bracket
by Belvedere
Fits Belvedere Bowls (Acrylic/ABS Plastic Bowls)
Package contains: Upper Metal Bracket and Lower Metal
Bracket
usually mounted with 4 wood screws (not included)
Shampoo Bowl Bracket * Fits Acrylic/ABS Bowls
*******************************************
Shampoo Bowl Mounting Bracket
Fits: Marble Bowls
Triangle Shape Metal Mounting Bracket Fits: Marble Products
Man made Marble Bowls
Has two taps turned out on top with holes to bolt into bottom of
Shampoo Bowl
Package contains: Metal Bracket and 1-Camber Bolt
usually mounted to wall with 4 wood screws ( not included )
Fits: Marble Products Model # 100, 200, 2000, 3000W and
4000 Marble Shampoo Bowls
Marble Shampoo Bowl Mounting Bracket
Fixtures - Parts - Accessories to shampoo bowls
Page 10
Koken Gypsy Bowl Bracket
Fits: Koken Gypsy Bowls( Picture on the left)
* Steel tube that has 2 - tubes that come from
back of bowl that fit under side lip of bowl, V Shape in back with 3 - Holes to mount to wall
with screws (screws Not included)
* Fits Only Koken Gypsy Bowl
* Note Gypsy bowl is a all thin plastic bowl
Koken Gypsy Bowl Mounting Bracket
This Bracket fits the shampoo bowl above.
********************************************************************
Koken / Takara Belmont Products
********************************************************************
Koken / Takara Belmont
Fixture
# 700 " Two Handle " Hot-Cold
Fits all older Belvedere & KOKEN Bowls
Replaces the Belvedere #112 fixture that is no longer made.
Chrome ( Solid Brass Workings )
Shampoo hoses sold separately on this page.
3" centers
Koken / Takara Belmont #700 Two Handle Fixture Chrome
Koken / Takara Belmont #900
same as above except Brass Plated Outside
Fixtures - Parts - Accessories to shampoo bowls
Page 11
*******************************************
Fixture/Part Handles (Set) Fits #700
* Fits Koken 2 - Handle Fixture
* Fits # 700 Fixture
* Crystal Clear Plastic Handles ( Hot and Cold )
* Includes Handles, Plastic Caps ( Hot and Cold ) and Screws
*******************************************
#550N Koken Single Lever Fixture
by Belmont
Single Lever Fixture
Fits Koken and Marble Shampoo Bowls.
Note: Fixture Opening in Bowl must be a Minimum
of 1-3/4" and a Maximum of 2" to accommodate
this fixture.
Fixtures - Parts - Accessories to shampoo bowls
Page 12
*******************************************
Marble Products
*******************************************
# 500 Fixture
The most advanced single control faucet made. Pull up for
exact pressure desired. Dial the temperature you like, left for
Hot, right for Cold. Turn water on or off without resetting. The
#500 "Dial-Flo" has only one moving part.
* Fits Marble, MPC & Koken Shampoo Bowls
Note: Fixture Opening in Bowl must be a Minimum
of 1-3/4" and a Maximum of 2" to accommodate
this fixture.
******************************************
Handle for Dial Flo #500 Fixture * Handle
Only * Before June 2005
* Fits: Marble 500 "Dial-Flo" Single Handle Fixture made
before June 2005
* Color: Crystal Clear
* Shape: Round Sides with Flat on top & Flat on Bottom
* Fastens on to fixture with Screw (included) under Cap
(button)
* Fits Fixture made before June 2005
* Has 9 ridges where it fits onto stem
******************************************
Fixtures - Parts - Accessories to shampoo bowls
Page 13
Fixture Dial Flo * Plug Button Only
* Plug Button "top to cover screw"
* Crystal Clear Plastic
* Fits #500 "Dial-Flo Faucet Handle
******************************************
Fixture Dial Flo #550 Fixture * Handle
Only *
After June 2005
Handle with Cap (button) and screw Only
* Fits: Marble 550 "Dial-Flo" Single Handle Fixture
* Color: Crystal Clear
* Shape: Round Sides with Flat on top & Flat on Bottom
* Fastens on to fixture with Screw (included) under Cap
(button)
* When looking into the bottom of handle where the handle
fastens onto the fixture it is "DIAMOND SHAPE"
* Fits Fixture made After June 2005
* This Fixture is turned on by pushing the handle backwards
and off by pulling handle forward
* Fits "DIAMOND SHAPE" stem
******************************************
Fixture Dial Flo Handle Cap * Only
* Plug Button "top to cover screw"
* Crystal Clear Plastic
* Fits #550 "Dial-Flo Faucet Handle
* Has "M P C" printed on button
Fixtures - Parts - Accessories to shampoo bowls
Page 14
******************************************
Fixture Dial Flo Cam (Stem) Only
* Before June 2005
* Fits: Marble 500 "Dial-Flo" Single Handle Fixture made
before June 2005
* Color: Gray Plastic
* Shape: 3/8" Round x 3-1/4" long with groves on one End for
Handle & Tapered on Bottom End
* Fits Fixture made before June 2005
* Has 8 ridges where it fits onto stem
Sold With Fixture Cartridge Kit Below
******************************************
Fixture Cartridge Kit & Dial Flo Cam
(Stem)
* Fits Marble #500 Dial-Flo Fixture
* "Leaky Faucet" this kit will replace the wore parts in the
#500 "Dial-Flo" Faucet by Marble Products Co.
* Fits "Pull Up" to turn on water Fixture ( #500 fixture)
* Includes: Cam (Stem), Sleeve, Cartridge and Gasket
Marble Cartridge Kit & Dial Flo Cam (Stem) for #500 Fixture
******************************************
Fixture Cartridge Kit
* Fits #550 Fixture
Fits #550 DIAL-FLO FAUCET BY Koken / MARBLE PRODUCTS
CO
* "Leaky Faucet" this kit will replace the wore parts in the
* Fits Push back to turn on & Pull forward to shut off Fixture
* Number printed on side of part "FL02GJ"
Fixtures - Parts - Accessories to shampoo bowls
Page 15
** Note Blue Cartridge is NO Longer Available
originally this fixture was made and sold with a BLUE color
cartridge
That fixture has been Discontinued because it was found to
be too tight, it was hard to turn on and off.
If you have a fixture with a blue cartridge you will need to buy
a
NEW FIXTURE.
*** The Green Cartridge shown here will
NOT fit your Blue Cartridge Fixture ***
******************************************
#400 Diverter Faucet Spout
* For use with #500 "Dial-Flo" or the Newer #550 Dial-Flo
single lever faucet and MPC # 1735 "Soft-Flo" Shampoo Hose
Spray.
* Faucet has 4-1/2" Swivel Spout with manual diverter knob.
* Pull up to divert water through spray hose, push down to
redirect through spout.
* Diverter Faucet Spout ONLY comes with hose to connect to
faucet
* Note: Opening in bowl must be a minimum of 1-5/16" and a
maximum of
1-7/16" to accommodate this fixture.
*******************************************
Vacuum Breaker
FITS: Marble # 10 Bowl & Collins Concept Bowl
Includes: Vacuum Breaker, Hose Receiver, and Hose to Fixture
to Breaker
* Dimension of Receiver 3-1/4" x 2-3/4"
This is a one way valve that saves the integrity of the fresh
water system by NOT allowing contaminate water (water
contaminated with perm solution, neutralizer, hair color, etc.)
from mixing with the fresh water system that we drink.
National Plumbing Code Number: ASSE 1001
Consult your local plumber and building codes for need of this
product.
Fixtures - Parts - Accessories to shampoo bowls
Page 16
******************************************
Marble Products Hose Receiver Kit for
Marble Vacuum Breaker
FITS: All Marble Product Shampoo Bowls & Collins Concept
Bowl
* Has 2 - 1/2" Holes just left of the hose to mount vacuum
breaker
* Fastens to shampoo bowl with steel bar with bolt & thumb
nut included
* Also included rubber gasket for receiver and vacuum breaker
* Dimension of Receiver 3-1/4" x 2-3/4"
* Material: CHROME PLASTIC
* Color: Chrome
***************** *************************
Marble Products Los Angeles Vacuum
Breaker
Includes: Los Angeles Vacuum Breaker Hose Receiver and 22"
Hose from Fixture to Breaker
* Dimension of Receiver: 3-1/4" x 2-3/4"
* TO BE USED FOR Los Angeles, California
Marble Los Angeles Vacuum Breaker
***************** *************************
Fixture Repair Kit Fits Marble Vacuum
Breaker
Marble Fixture Repair Kit fits marble Vacuum Breaker
* Includes: Black O-Ring and White Plastic Valve with Red
Rubber Washer
******************************************
Fixtures - Parts - Accessories to shampoo bowls
Page 17
Connecting Hose for Marble Vacuum
Breaker
This is the HOSE that connects the Vacuum Breaker to the
Fixture
The length is about 24" long with female couplings on each
end
The hose is 3/8" inside diameter (ID) 250 PSI
*******************************************
Soft-Flo Shampoo Hose
by Marble Products
Screws on to Fixture
Length: 42 inches
*******************************************
" Catch-All "
Hair Trap
Model #1701
z
z
Prevents hair from
clogging the shampoo
bowl drain.
Fits existing brand or
model of shampoo
bowl drain.
Fixtures - Parts - Accessories to shampoo bowls
Page 18
Shampoo Bowl Hole Cover Fits: Marble
Bowls
Hole Cover
Chrome Cover plate with rubber seal washer and bottom
washer with wing nut fastener.
Fits: Marble Products Man made Marble and Fiberglass
Shampoo Bowls
******************************************
Hose Receiver Kit for Jeffco Brand
Vacuum Breaker
* Has 2 - 1/2" Holes just left of the hose to mount vacuum
breaker
* Fastens to shampoo bowl with steel bar with bolt & thumb
nut included
* Also included rubber gasket for receiver and vacuum breaker
* Dimension of Receiver 3-1/4" x 2-3/4"
* Material: CHROME PLASTIC
* Color: Chrome
Fixtures - Parts - Accessories to shampoo bowls
Page 19
Marble Products Hose Receiver Kit For
Shampoo Bowl
* Fastens to shampoo bowl with steel bar with bolt & thumb
nut included
* Also included rubber gasket for receiver
* Dimension of Receiver 3-1/4" x 2-3/4"
* Material: CHROME PLASTIC
* Color: Chrome
Marble Hose Receiver Kit for Shampoo Bowl
******************************************
Marble Products Brand Complete
3 1/2" Strainer Assembly
Includes:
3-1/2" Hair Strainer Cup, Strainer Body, Cardboard Gasket,
Locknut,
1-1/2" Drain Tailpiece Tube, Tube Washer, Tube Slip Nut
* Fits All Marble Products Brand Shampoo Bowls
* Including: Fiberglass Bowls # 10 & # 30
* Cultured Marble Bowls #100, 200, 2000, 3000W, 4000, 300
& 2001
******************************************
Marble Products Shampoo Bowl Strainer
Cup
* 3-1/2" Diameter
Fits: Marble Products Shampoo Bowls
* 3-1/2" Diameter
* Material: Plastic
* Color: Black/Gray
Fixtures - Parts - Accessories to shampoo bowls
Page 20
Jeffco Fixture #570 Single Handle
Chrome
MODEL 570
Fits: Jeffco Shampoo Bowls and Marble Products
Chrome Lever -Handle
* Fixture Opening in Bowl must be a Minimum of 1-1/2" and a
Maximum of 2-1/4" to accommodate this fixture
* Height from sink to top of fixture when opened is 6"
Meets ASME A112.18.1-2003/ CSA B 125-01
******************************************
Jeffco Fixture Cartridge for #570 Single
Handle
Jefco Fixture Cartridge for #570 Single Handle
Fits: Jeffco Shampoo Bowls
Meets ASME A112.18.1-2003/ CSA B 125-01
******************************************
Jeffco Shampoo Bowl Vacuum
Breaker
Includes: Vacuum Breaker, Hose Receiver, and
Hose to Fixture to Breaker
* Dimension of Receiver 3-1/4" x 2-3/4"
* Jeffco Brand
* National Plumbing Code Number: ASSE 1001
This is a one way valve that saves the integrity of
the fresh water system by NOT allowing
contaminate water (water contaminated with perm
solution, neutralizer, hair color, etc.) from mixing
with the fresh water system that we drink.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement